MIBs Depot

SLE-MPLS-TP-TUNNEL-MIB

Registered at
1.3.6.1.4.1.6296.101.16.14
Last updated
2015-10-07 00:00
Organization
Multiprotocol Label Switching (MPLS) Working Group
Revisions
2004-06-03 00:00
Namespace
dasan
Source file
SLE-MPLS-TP-TUNNEL-MIB
Digest
sha256:ede29e13feb4f5916422ca1449c9eb132bd93f3defd06294e4f1853e3d80b270

Description

Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212, January 2002 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, [RFC2702], September 1999

Contact

Gyerok Kwon Dasan Networks Email: grkwon@dasannetworks.com Kantharaj B M Dasan Networks Email: kanth@dasannetworks.com DongChel Shin (Chris) Dasan Networks Email: dchshin@dasannetworks.com Comments about this document should be emailed directly to the Dasan support email ID at support@dasannetworks.com.

Imports

FromSymbols
DASAN-SMIsleMgmt
IF-MIBInterfaceIndexOrZero, ifCounterDiscontinuityGroup, ifGeneralInformationGroup
MPLS-TC-EXT-STD-MIBMplsCcId, MplsIccId
MPLS-TC-STD-MIBMplsLabel, mplsStdMIB
SLE-TC-MIBSleControlRequestResultType, SleControlStatusType
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIGauge32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso, zeroDotZero
SNMPv2-TCDisplayString, MacAddress, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DASAN-SMI
IANAifType-MIB
IF-MIB
MPLS-TC-EXT-STD-MIB
MPLS-TC-STD-MIB
SLE-MPLS-TP-TUNNEL-MIB
SLE-TC-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
sleMpls
OBJECT-IDENTITY
SLE MPLS.
1.3.6.1.4.1.6296.101.16current
sleMplsTpTunnelCfg
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.16.14.1
sleMplsTpTunnelCfgInfoTable
OBJECT-TYPE
The mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that only point-to-point tunnel segments are supported, although multipoint-to-point and point- to-multipoint connections are supported by an LSR acting as a cross-connect. Each MPLS tunnel can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR.
1.3.6.1.4.1.6296.101.16.14.1.1not-accessiblecurrent
sleMplsTpTunnelCfgInfoEntry
OBJECT-TYPE
An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signalling protocol. Whenever a new entry is created with mplsTunnelIsIf set to true(1), then a corresponding entry is created in ifTable as well (see RFC 2863). The ifType of this entry is mplsTunnel(150). A tunnel entry needs to be uniquely identified across a MPLS network. Indices mplsTunnelIndex and mplsTunnelInstance uniquely identify a tunnel on the LSR originating the tunnel. To uniquely identify a tunnel across an MPLS network requires index mplsTunnelIngressLSRId. The last index mplsTunnelEgressLSRId is useful in identifying all instances of a tunnel that terminate on the same egress LSR.
1.3.6.1.4.1.6296.101.16.14.1.1.1not-accessiblecurrent
sleMplsTpTunnelCfgInfoIndex
OBJECT-TYPE
A unique value which identify an entry in this table.
1.3.6.1.4.1.6296.101.16.14.1.1.1.1Unsigned32 (0..65535)not-accessiblecurrent
sleMplsTpTunnelCfgInfoName
OBJECT-TYPE
The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to mplsTunnelName. Also see the description of ifName in RFC 2863.
1.3.6.1.4.1.6296.101.16.14.1.1.1.2OCTET STRING (SIZE(0..16))read-onlycurrent
sleMplsTpTunnelCfgInfoId
OBJECT-TYPE
Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2) this value SHOULD be equal to the value signaled in the Tunnel Id of the Session object. When the MPLS signalling protocol is crldp(3) this value SHOULD be equal to the value signaled in the LSP ID.
1.3.6.1.4.1.6296.101.16.14.1.1.1.3Unsigned32 (1..65535)read-onlycurrent
sleMplsTpTunnelCfgInfoSrcIdType
OBJECT-TYPE
This object is used to set the ietf or itut type.
1.3.6.1.4.1.6296.101.16.14.1.1.1.4INTEGER {ietf(1), itut(2)}read-onlycurrent
sleMplsTpTunnelCfgInfoSrcGId
OBJECT-TYPE
This Object is used to display the GlobalID of IETF
1.3.6.1.4.1.6296.101.16.14.1.1.1.5Unsigned32 (1..4294967295)read-onlycurrent
sleMplsTpTunnelCfgInfoSrcCc
OBJECT-TYPE
This Object is used to display the Source CC-ID of ITUT
1.3.6.1.4.1.6296.101.16.14.1.1.1.6MplsCcIdread-onlycurrent
sleMplsTpTunnelCfgInfoSrcIcc
OBJECT-TYPE
This Object is used to set the Source ICC-ID of ITUT
1.3.6.1.4.1.6296.101.16.14.1.1.1.7MplsIccIdread-onlycurrent
sleMplsTpTunnelCfgInfoSrcNodeId
OBJECT-TYPE
This Object is used to display the Source Node ID of IETF and ITUT
1.3.6.1.4.1.6296.101.16.14.1.1.1.8IpAddressread-onlycurrent
sleMplsTpTunnelCfgInfoDestIdType
OBJECT-TYPE
This object is used to set the ietf or itut type.
1.3.6.1.4.1.6296.101.16.14.1.1.1.9INTEGER {ietf(1), itut(2)}read-onlycurrent
sleMplsTpTunnelCfgInfoDestGId
OBJECT-TYPE
This Object is used to set the Destination GlobalID of IETF
1.3.6.1.4.1.6296.101.16.14.1.1.1.10Unsigned32 (1..4294967295)read-onlycurrent
sleMplsTpTunnelCfgInfoDestCc
OBJECT-TYPE
This Object is used to display the Destination CC-ID of ITUT
1.3.6.1.4.1.6296.101.16.14.1.1.1.11MplsCcIdread-onlycurrent
sleMplsTpTunnelCfgInfoDestIcc
OBJECT-TYPE
This Object is used to set the Destination ICC-ID of ITUT
1.3.6.1.4.1.6296.101.16.14.1.1.1.12MplsIccIdread-onlycurrent
sleMplsTpTunnelCfgInfoDestNodeId
OBJECT-TYPE
This Object is used to display the Destination Node ID of IETF and ITUT
1.3.6.1.4.1.6296.101.16.14.1.1.1.13IpAddressread-onlycurrent
sleMplsTpTunnelCfgInfoMode
OBJECT-TYPE
This object is used to set the Tunnel Mode
1.3.6.1.4.1.6296.101.16.14.1.1.1.14INTEGER {none(0), unidirectional(1), bidirectional(2), corouted(3), associate(4)}read-onlycurrent
sleMplsTpTunnelCfgInfoFwdInLabel
OBJECT-TYPE
This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575.. The default value 1048576 is invalid label
1.3.6.1.4.1.6296.101.16.14.1.1.1.15MplsLabelread-onlycurrent
sleMplsTpTunnelCfgInfoFwdInIfIndex
OBJECT-TYPE
This object is used to set the Forward IN Interface index
1.3.6.1.4.1.6296.101.16.14.1.1.1.16InterfaceIndexOrZeroread-onlycurrent
sleMplsTpTunnelCfgInfoFwdOperation
OBJECT-TYPE
This object is used to set the Forward Ilm OPeration .
1.3.6.1.4.1.6296.101.16.14.1.1.1.17INTEGER {none(0), push(1), pop(2), swap(3)}read-onlycurrent
sleMplsTpTunnelCfgInfoFwdOutLabel
OBJECT-TYPE
This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label
1.3.6.1.4.1.6296.101.16.14.1.1.1.18MplsLabelread-onlycurrent
sleMplsTpTunnelCfgInfoFwdOutIfIndex
OBJECT-TYPE
This object is used to set the Forward OUT Interface index
1.3.6.1.4.1.6296.101.16.14.1.1.1.19InterfaceIndexOrZeroread-onlycurrent
sleMplsTpTunnelCfgInfoFwdOutMac
OBJECT-TYPE
This object is used to display the Forward OUT MAC ADDRESS
1.3.6.1.4.1.6296.101.16.14.1.1.1.20MacAddressread-onlycurrent
sleMplsTpTunnelCfgInfoRevInLabel
OBJECT-TYPE
This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label
1.3.6.1.4.1.6296.101.16.14.1.1.1.21MplsLabelread-onlycurrent
sleMplsTpTunnelCfgInfoRevInIfIndex
OBJECT-TYPE
This object is used to set the Reverse IN Interface index
1.3.6.1.4.1.6296.101.16.14.1.1.1.22InterfaceIndexOrZeroread-onlycurrent
sleMplsTpTunnelCfgInfoRevOperation
OBJECT-TYPE
This object is used to set the Reverse Ilm OPeration .
1.3.6.1.4.1.6296.101.16.14.1.1.1.23INTEGER {none(0), push(1), pop(2), swap(3)}read-onlycurrent
sleMplsTpTunnelCfgInfoRevOutLabel
OBJECT-TYPE
This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label
1.3.6.1.4.1.6296.101.16.14.1.1.1.24MplsLabelread-onlycurrent
sleMplsTpTunnelCfgInfoRevOutIfIndex
OBJECT-TYPE
This object is used to set the Reverse OUT Interface index
1.3.6.1.4.1.6296.101.16.14.1.1.1.25InterfaceIndexOrZeroread-onlycurrent
sleMplsTpTunnelCfgInfoRevOutMac
OBJECT-TYPE
This object is used to display the Forward OUT MAC ADDRESS .
1.3.6.1.4.1.6296.101.16.14.1.1.1.26MacAddressread-onlycurrent
sleMplsTpTunnelCfgInfoState
OBJECT-TYPE
This object is to display status of the tunnel.
1.3.6.1.4.1.6296.101.16.14.1.1.1.27INTEGER {up(1), down(2)}read-onlycurrent
sleMplsTpTunnelCfgInfoRole
OBJECT-TYPE
This object is to display Role of the tunnel.
1.3.6.1.4.1.6296.101.16.14.1.1.1.28INTEGER {source(0), transist(1), destination(2)}read-onlycurrent
sleMplsTpTunnelCfgInfoAssociateTnlName
OBJECT-TYPE
This object to display associate of reverse tunnel.
1.3.6.1.4.1.6296.101.16.14.1.1.1.29OCTET STRINGread-onlycurrent
sleMplsTpTunnelCfgInfoDescription
OBJECT-TYPE
Description.
1.3.6.1.4.1.6296.101.16.14.1.1.1.30OCTET STRINGread-onlycurrent
sleMplsTpTunnelCfgInfoHlspRole
OBJECT-TYPE
This object is used to set the Hlsp Tunnel. whether the tunnel is Server or client. server (1) :- To set the Server Tunnel client(2) :- To set the Client Tunnel .
1.3.6.1.4.1.6296.101.16.14.1.1.1.31INTEGER {server(1), client(2)}read-onlycurrent
sleMplsTpTunnelCfgInfoHlspServerTunnelName
OBJECT-TYPE
This object is used to set the server TunnelName, when sleMplsTpTunnelCfgControlHlspOption as a client .
1.3.6.1.4.1.6296.101.16.14.1.1.1.32OCTET STRINGread-onlycurrent
sleMplsTpTunnelCfgInfoQosPolicyName
OBJECT-TYPE
This object is used to set the Qos Policy name.
1.3.6.1.4.1.6296.101.16.14.1.1.1.33OCTET STRINGread-onlycurrent
sleMplsTpTunnelCfgControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.16.14.1.2
sleMplsTpTunnelCfgControlRequest
OBJECT-TYPE
This object holds the possible read-write columns that can be modified in the Tunnel table. For each read-write column of Tunnel table, a Set Operation controlvalue is added in this object.
1.3.6.1.4.1.6296.101.16.14.1.2.1INTEGER {createMplsTpTunnelEntry(1), deleteMplsTpTunnelEntry(2), setMplsTpTunnelMode(3), setNhlfe(4), setIlmPop(5), setIlmSwap(6), setAssociateTunnel(7), unsetNhlfe(8), unsetIlmPop(9), unsetIlmSwap(10), unsetAssociateTunnel(11), setDescription(12), setHlspServerLsp(13), setHlspClientLsp(14), unsetHlspServerLsp(15), unsetHlspClientLsp(16), setTunnelQosPolicyName(17), unsetTunnelQosPolicyName(18)}read-writecurrent
sleMplsTpTunnelCfgControlStatus
OBJECT-TYPE
This object displays the status of the configuration done.
1.3.6.1.4.1.6296.101.16.14.1.2.2SleControlStatusTyperead-onlycurrent
sleMplsTpTunnelCfgControlTimer
OBJECT-TYPE
This object is based on the SLE style where a timer is configured for every control table.
1.3.6.1.4.1.6296.101.16.14.1.2.3Gauge32read-writecurrent
sleMplsTpTunnelCfgControlTimeStamp
OBJECT-TYPE
This object specifies the time at which the configuration is done.
1.3.6.1.4.1.6296.101.16.14.1.2.4TimeTicksread-onlycurrent
sleMplsTpTunnelCfgControlReqResult
OBJECT-TYPE
The standard result of the SET operation is stored here.
1.3.6.1.4.1.6296.101.16.14.1.2.5SleControlRequestResultTyperead-onlycurrent
sleMplsTpTunnelCfgControlName
OBJECT-TYPE
The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to SlemplsTunnelName. Also see the description of ifName in RFC 2863.
1.3.6.1.4.1.6296.101.16.14.1.2.6OCTET STRING (SIZE(0..16))read-writecurrent
sleMplsTpTunnelCfgControlId
OBJECT-TYPE
This object is used to set the tunnel Id .
1.3.6.1.4.1.6296.101.16.14.1.2.7Unsigned32 (1..65535)read-writecurrent
sleMplsTpTunnelCfgControlSrcIdType
OBJECT-TYPE
This object is used to set the ietf or itut type.
1.3.6.1.4.1.6296.101.16.14.1.2.8INTEGER {ietf(1), itut(2)}read-writecurrent
sleMplsTpTunnelCfgControlSrcGId
OBJECT-TYPE
This object is used to set the source Global-Id for IETF .
1.3.6.1.4.1.6296.101.16.14.1.2.9Unsigned32 (1..4294967295)read-writecurrent
sleMplsTpTunnelCfgControlSrcCc
OBJECT-TYPE
This object is used to set the source CC-ID for ITUT.
1.3.6.1.4.1.6296.101.16.14.1.2.10MplsCcIdread-writecurrent
sleMplsTpTunnelCfgControlSrcIcc
OBJECT-TYPE
This object is used to set the Source ICC-ID for ITUT.
1.3.6.1.4.1.6296.101.16.14.1.2.11MplsIccIdread-writecurrent
sleMplsTpTunnelCfgControlSrcNodeId
OBJECT-TYPE
This object is used to set the Source Node-Id for IETF and ITUT
1.3.6.1.4.1.6296.101.16.14.1.2.12IpAddressread-writecurrent
sleMplsTpTunnelCfgControlDestIdType
OBJECT-TYPE
This object is used to set the ietf or itut type.
1.3.6.1.4.1.6296.101.16.14.1.2.13INTEGER {ietf(1), itut(2)}read-writecurrent
sleMplsTpTunnelCfgControlDestGId
OBJECT-TYPE
This object is used to set the Destination Global-Id for IETF .
1.3.6.1.4.1.6296.101.16.14.1.2.14Unsigned32 (1)read-writecurrent
sleMplsTpTunnelCfgControlDestCc
OBJECT-TYPE
This object is used to set the Destination CC-ID for ITUT.
1.3.6.1.4.1.6296.101.16.14.1.2.15MplsCcIdread-writecurrent
sleMplsTpTunnelCfgControlDestIcc
OBJECT-TYPE
This object is used to set the Destination ICC-ID for ITUT.
1.3.6.1.4.1.6296.101.16.14.1.2.16MplsIccIdread-writecurrent
sleMplsTpTunnelCfgControlDestNodeId
OBJECT-TYPE
This object is used to set the Destination NodeID for IETF and ITUT.
1.3.6.1.4.1.6296.101.16.14.1.2.17IpAddressread-writecurrent
sleMplsTpTunnelCfgControlMode
OBJECT-TYPE
This object is used to set the Tunnel mode .
1.3.6.1.4.1.6296.101.16.14.1.2.18INTEGER {unidirectional(1), bidirectional(2)}read-writecurrent
sleMplsTpTunnelCfgControlPath
OBJECT-TYPE
This object is used to Set the forward path and reverse path tunnel.
1.3.6.1.4.1.6296.101.16.14.1.2.19INTEGER {forwardPath(1), reversePath(2)}read-writecurrent
sleMplsTpTunnelCfgControlInLabel
OBJECT-TYPE
This object is used to set the Inlabel.
1.3.6.1.4.1.6296.101.16.14.1.2.20MplsLabelread-writecurrent
sleMplsTpTunnelCfgControlInInterface
OBJECT-TYPE
This object is used to set the Ininterface index.
1.3.6.1.4.1.6296.101.16.14.1.2.21InterfaceIndexOrZeroread-writecurrent
sleMplsTpTunnelCfgControlOperation
OBJECT-TYPE
This object is used to set the operation of Tuunel
1.3.6.1.4.1.6296.101.16.14.1.2.22INTEGER {push(1), pop(2), swap(3)}read-writecurrent
sleMplsTpTunnelCfgControlOutLabel
OBJECT-TYPE
This object is used to set the outlabel.
1.3.6.1.4.1.6296.101.16.14.1.2.23MplsLabelread-writecurrent
sleMplsTpTunnelCfgControlOutInterface
OBJECT-TYPE
This object is used to set the outerinterface index.
1.3.6.1.4.1.6296.101.16.14.1.2.24InterfaceIndexOrZeroread-writecurrent
sleMplsTpTunnelCfgControlOutMacAddress
OBJECT-TYPE
This object is used to Set the Out MacAddress .
1.3.6.1.4.1.6296.101.16.14.1.2.25MacAddressread-writecurrent
sleMplsTpTunnelCfgControlAssociateTnlName
OBJECT-TYPE
This object is used to Associated Forward tunnel and reverse tunnel with reverse tunnel name .
1.3.6.1.4.1.6296.101.16.14.1.2.26OCTET STRINGread-writecurrent
sleMplsTpTunnelCfgControlDescription
OBJECT-TYPE
Description.
1.3.6.1.4.1.6296.101.16.14.1.2.27OCTET STRINGread-writecurrent
sleMplsTpTunnelCfgControlHlspSeverTunnelName
OBJECT-TYPE
This object is used to set the server Tunnel name for associating server and client.
1.3.6.1.4.1.6296.101.16.14.1.2.28OCTET STRINGread-writecurrent
sleMplsTpTunnelCfgControlQosPolicyName
OBJECT-TYPE
This object is used to set the Qos Policy name.
1.3.6.1.4.1.6296.101.16.14.1.2.29OCTET STRINGread-writecurrent