MIBs Depot

SLE-MLSQOS-MIB

Registered at
1.3.6.1.4.1.6296.101.28
Last updated
2013-10-04 09:03
Organization
Revisions
2013-08-04 09:03
Namespace
dasan
Source file
SLE-MLSQOS-MIB
Digest
sha256:4db4acf9fa134938dc4199241973932f6a2e7b143aca57c3d820e885eb34ef99

Description

This MIB contains all informations about ML QOS supported features.

Imports

FromSymbols
DASAN-SMIsleMgmt
SLE-TC-MIBSleControlRequestResultType, SleControlStatusType
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter64, Gauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DASAN-SMI
SLE-MLSQOS-MIB
SLE-TC-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
ACLEtherType
TEXTUAL-CONVENTION
WORD Ethertype value - (0x600-0xffff) ip4 IPv4 Ethertype - 0x0800 ip6 IPv6 Ethertype - 0x86dd mpls MPLS Ethertype - 0x8847
current
ACLIpType
TEXTUAL-CONVENTION
src(1) Src Mac dst(2) Dst Mac srcWildcard(3) Src Wildcard bits dstWildcard(4) Dst Wildcard Bits host(5) any(6)
current
ACLMacType
TEXTUAL-CONVENTION
src(1) Src Mac dst(2) Dst Mac srcWildcard(3) Src Wildcard bits dstWildcard(4) Dst Wildcard Bits
current
ACLMatchActionType
TEXTUAL-CONVENTION
deny(0) deny the packets permit(1) permit. remark(2) mark the packets
current
ACLMatchType
TEXTUAL-CONVENTION
ACL Match Types mac (1), EthType (2) L3Proto(3)
current
AclTcpUdpPortActionType
TEXTUAL-CONVENTION
eq(1) Equals to neq(2) Not equals to lt(3) Lower Than gt(4) Greather Than
current
ClassMapMatchRangeType
TEXTUAL-CONVENTION
tcpSrcPort (1), tcpDstPort (2), udpSrcPort (3), udpDstPort (4), VlanId (5), layer4SrcPort (6), layer4DstPort (7)
current
ClassMapMatchType
TEXTUAL-CONVENTION
cos (1) , innerCos(2), ipDscp (3), ipPrecedence (4), ip6Dscp (5), ip6Precedence (6), tcpSrcPort (7), tcpDstPort (8), udpSrcPort (9), udpDstPort (10), VlanId (11), innerVlanId (12), layer4SrcPort (13) layer4DstPort (14)
current
MlsQosInterfaceMapingType
TEXTUAL-CONVENTION
cos (1) Configure interface default CoS values cos-cos (2) Specify cos-cos cos-queue (3) Specify cos-queue map dscp (4) Set the default DSCP vlaue dscp-dscp(5) Specify dscp-dscp dscp-queue (6) DSCP-to-QUEUE exp-exp(7) Specify exp-exp trust (8) Configure port trust state trust-passthrough (9) COnfigure port trust pass-through state cosToClass (10) configure cos to class dscpToClass (11) configure dscp to class
current
MlsQosIntfQueProfilingType
TEXTUAL-CONVENTION
shaping (1), wrrQWt (2), wrrRandomDetect (3), tailDrop (4), strictQ (5)
current
MlsQosIntfTrustState
TEXTUAL-CONVENTION
cos (1) dscp (2)
current
MlsQosMappingType
TEXTUAL-CONVENTION
CosToCos(1) : CosToQueue(2) : DscpToDscp(3) : DscpToQueue(4) : ExpToExp(5) : ExpToQueue(6) :
current
MlsQosStatusType
TEXTUAL-CONVENTION
Enable(1) : enabled in the system. Disable(0) : Disable in system.
current
PmapExceedActionType
TEXTUAL-CONVENTION
none (0) drop (1) set-dscp-transmit (2) set-tos-transmit (3) set-cos-transmit (4) transmit (7)
current
PmapPoliceType
TEXTUAL-CONVENTION
srtcm(1) trtcm(2)
current
PmapPriorityType
TEXTUAL-CONVENTION
low(0) medium(1) high(2) highest(3)
current
PmapSetActionType
TEXTUAL-CONVENTION
cos (1), cpu-cos (2), ip-dscp (3), ip-precedence (4), redirect-to-port (5), mirror-to-port (6), vlan (7), ip6-dscp (8), ip6-precedence (9), cpu-copy (10), deny (11), qos-group(12), none(13), queue(14), vlan-cos(15)
current
PmapViolateActionType
TEXTUAL-CONVENTION
none(0) drop(1) set-dscp-transmit(2) set-cos-transmit(3) set-tos-transmit(4) transmit (5)
current
PolMapClassMatchPrioType
TEXTUAL-CONVENTION
high(1) : highest(2) : low(3) : medium(4) :
current
PoliceExceedActionType
TEXTUAL-CONVENTION
drop(1) : set-cos-transmit(2) : set-dscp-transmit(3) : set-tos-transmit(4) : transmit (5)
current

Objects

NameOIDSyntaxAccessStatus
sleMlsQosGlobal
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.1
sleMlsQosGlobalInfo
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.1.1
sleMlsQosStatus
OBJECT-TYPE
Enable / Disable MlQos enable (1) disable (0)
1.3.6.1.4.1.6296.101.28.1.1.1MlsQosStatusTyperead-onlycurrent
sleMlsQosMapCosToCos
OBJECT-TYPE
Global incoming Cos to outgoing Cos mapping.
1.3.6.1.4.1.6296.101.28.1.1.2OCTET STRINGread-onlycurrent
sleMlsQosMapCosToQueue
OBJECT-TYPE
Global incoming Cos to outgoing queue mapping.
1.3.6.1.4.1.6296.101.28.1.1.3OCTET STRINGread-onlycurrent
sleMlsQosMapDscpToDscp
OBJECT-TYPE
Global incoming dscp to outgoing dscp mapping.
1.3.6.1.4.1.6296.101.28.1.1.4OCTET STRINGread-onlycurrent
sleMlsQosMapDscpToQueue
OBJECT-TYPE
Global incoming dscp to outgoing queue mapping.
1.3.6.1.4.1.6296.101.28.1.1.5OCTET STRINGread-onlycurrent
sleMlsQosMapExpToExp
OBJECT-TYPE
Global incoming exp to outgoing exp mapping.
1.3.6.1.4.1.6296.101.28.1.1.6OCTET STRINGread-onlycurrent
sleMlsQosMapExpToQueue
OBJECT-TYPE
Global incoming exp to outgoing queue mapping.
1.3.6.1.4.1.6296.101.28.1.1.7OCTET STRINGread-onlycurrent
sleMlsQosMapStrictQueueId
OBJECT-TYPE
Queues with Strict scheduling
1.3.6.1.4.1.6296.101.28.1.1.8OCTET STRINGread-onlycurrent
sleMlsQosMapWrrQueueWeight
OBJECT-TYPE
Queue weight for Weighted round robin scheduling. If the queue wt is given 0, then the queue becomes strict queue
1.3.6.1.4.1.6296.101.28.1.1.9OCTET STRINGread-onlycurrent
sleMlsQosMapCpuMaxPpsRate
OBJECT-TYPE
Rate limiting for CPU. Defines Max packets per second to CPU
1.3.6.1.4.1.6296.101.28.1.1.10OCTET STRINGread-onlycurrent
sleMlsQosMapCpuQueueWeight
OBJECT-TYPE
weight for Cpu Queues
1.3.6.1.4.1.6296.101.28.1.1.11OCTET STRINGread-onlycurrent
sleMlsQosMapNodeCpuMaxPpsRate
OBJECT-TYPE
node Rate limiting for CPU. Defines Max packets per second to CPU
1.3.6.1.4.1.6296.101.28.1.1.12OCTET STRINGread-onlycurrent
sleMlsQosMapNodeCpuQueueWeight
OBJECT-TYPE
node weight for Cpu Queues
1.3.6.1.4.1.6296.101.28.1.1.13OCTET STRINGread-onlycurrent
sleMlsQosMapExpToClass
OBJECT-TYPE
Exp - to - class mapping
1.3.6.1.4.1.6296.101.28.1.1.14OCTET STRINGread-onlycurrent
sleHQosStatistics
OBJECT-TYPE
Hqos has feature to disable or enable statistics so this object is only applicable when hqos is enabled
1.3.6.1.4.1.6296.101.28.1.1.15MlsQosStatusTyperead-onlycurrent
sleQosPhbPriorityColor
OBJECT-TYPE
qos phb-priority-color Ex: PHB Name | Priority Color ------------------------------------------- be | 0 red cs0 | 0 green cs1 | 1 green af11 | 1 yellow af12 | 1 red af13 | 0 green cs2 | 2 green af21 | 2 green af22 | 2 yellow af23 | 2 red cs3 | 3 green af31 | 4 red af32 | 3 green af33 | 3 yellow cs4 | 4 green af41 | 5 yellow af42 | 5 red af43 | 4 green cs5 | 5 green ef | 6 red cs6 | 6 yellow cs7 | 7 green
1.3.6.1.4.1.6296.101.28.1.1.16OCTET STRINGread-onlycurrent
sleHQosDefaultClassToDscp
OBJECT-TYPE
Default Class to DSCP Ex: QoS PHB map to DSCP: PHB Name | dscp ------------------------------------------- be | 0 be | 0 cs1 | 9 af11 | 10 af12 | 12 af13 | 14 cs2 | 16 af21 | 18 af22 | 20 af23 | 22 cs3 | 24 af31 | 26 af32 | 28 af33 | 30 cs4 | 32 af41 | 34 af42 | 35 af43 | 38 cs5 | 40 ef | 46 cs6 | 48 cs7 | 56
1.3.6.1.4.1.6296.101.28.1.1.17OCTET STRINGread-onlycurrent
sleQosDefaultCosToClassTrust
OBJECT-TYPE
qos default cos to class trust Ex:QoS Cos+Cfi/DEI to CLASS: COS CFI/DEI | CLASS ------------------------------------------- 0 0 | cs0 0 1 | cs0 1 0 | cs1 1 1 | cs1 2 0 | cs2 2 1 | cs2 3 0 | cs3 3 1 | cs3 4 0 | cs4 4 1 | cs4 5 0 | cs5 5 1 | cs5 6 0 | cs6 6 1 | cs6 7 0 | cs7 7 1 | cs7
1.3.6.1.4.1.6296.101.28.1.1.18OCTET STRINGread-onlycurrent
sleQosDefaultCosToClassNoTrust
OBJECT-TYPE
qos Default cos to class no trust Ex: QoS Cos+Cfi/DEI to CLASS: COS CFI/DEI | CLASS ------------------------------------------- 0 0 | be 0 1 | be 1 0 | be 1 1 | be 2 0 | be 2 1 | be 3 0 | be 3 1 | be 4 0 | be 4 1 | be 5 0 | be 5 1 | be 6 0 | be 6 1 | be 7 0 | be 7 1 | be
1.3.6.1.4.1.6296.101.28.1.1.19OCTET STRINGread-onlycurrent
sleQosDefaultDscpToClassTrust
OBJECT-TYPE
qos default dscp to class trust Ex: QoS Dscp to CLASS: DSCP | CLASS ------------------------------------------- 0 | be 1 | be 2 | be 3 | be 4 | be 5 | be 6 | be 7 | be 8 | cs1 9 | be 10 | af11 11 | be 12 | af12 13 | be 14 | af13 15 | be 16 | cs2 17 | be 18 | af21 19 | be 20 | af22 21 | be 22 | af23 23 | be 24 | cs3 25 | be 26 | af31 27 | be 28 | af32 29 | be 30 | af33 31 | be 32 | cs4 33 | be 34 | af41 35 | be 36 | af42 37 | be 38 | af43 39 | be 40 | cs5 41 | be 42 | be 43 | be 44 | be 45 | be 46 | ef 47 | be 48 | cs6 49 | be 50 | be 51 | be 52 | be 53 | be 54 | be 55 | be 56 | cs7 57 | be 58 | be 59 | be 60 | be 61 | be 62 | be 63 | be
1.3.6.1.4.1.6296.101.28.1.1.20OCTET STRINGread-onlycurrent
sleQosDefaultDscpToClassNoTrust
OBJECT-TYPE
qos defualt dscp to class no trust Ex: QoS Dscp to CLASS: DSCP | CLASS ------------------------------------------- 0 | be 1 | be 2 | be 3 | be 4 | be 5 | be 6 | be 7 | be 8 | be 9 | be 10 | be 11 | be 12 | be 13 | be 14 | be 15 | be 16 | be 17 | be 18 | be 19 | be 20 | be 21 | be 22 | be 23 | be 24 | be 25 | be 26 | be 27 | be 28 | be 29 | be 30 | be 31 | be 32 | be 33 | be 34 | be 35 | be 36 | be 37 | be 38 | be 39 | be 40 | be 41 | be 42 | be 43 | be 44 | be 45 | be 46 | be 47 | be 48 | be 49 | be 50 | be 51 | be 52 | be 53 | be 54 | be 55 | be 56 | be 57 | be 58 | be 59 | be 60 | be 61 | be 62 | be 63 | be
1.3.6.1.4.1.6296.101.28.1.1.21OCTET STRINGread-onlycurrent
sleMlsQosGlobalControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.1.2
sleMlsQosGlobalControlRequest
OBJECT-TYPE
The configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.1.2.1INTEGER {setMlQosStatus(1), setMlsQosMapping(2), unSetMlsQosMapping(3), setMlsQosStrictQueue(4), unSetMlsQosStrictQueue(5), setMlsQosWrr(6), unSetMlsQosWrr(7), setMlsQosCpuRate(8), setMlsQosCpuQueueWt(9), setMlsQosNodeCpuRate(10), setMlsQosNodeCpuQueueWt(11), setHQosStatistics(12), unsetHQosStatistics(13)}read-writecurrent
sleMlsQosGlobalControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.1.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosGlobalCtrlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.1.2.3Gauge32read-writecurrent
sleMlsQosGlobalControlTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.1.2.4TimeTicksread-onlycurrent
sleMlsQosGlobalControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.1.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosCtrlGlobalStatus
OBJECT-TYPE
Enable / Disable MlQos enable (1) disable (0)
1.3.6.1.4.1.6296.101.28.1.2.6MlsQosStatusTyperead-writecurrent
sleMlsQosGlobalControlMappingType
OBJECT-TYPE
Below Mapping Types can be configured cosToCos(1), cosToQueue(2), dscpToDscp(3), dscpToQueue(4), expToExp(5), expToQueue(6) expToClass(7)
1.3.6.1.4.1.6296.101.28.1.2.7MlsQosMappingTyperead-writecurrent
sleMlsQosGlobalControlMappingIngValue
OBJECT-TYPE
Ingress or incoming mapping values. Based on sleMlsQosGlobalControlMappingType, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = cosToCos, then sleMlsQosGlobalControlMappingIngValue = Incoming or ingress COS value
1.3.6.1.4.1.6296.101.28.1.2.8Integer32read-writecurrent
sleMlsQosGlobalControlMappingEgrValue
OBJECT-TYPE
Egress or outgoing mapping values. Based on sleMlsQosGlobalControlMappingType, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = cosToCos, then sleMlsQosGlobalControlMappingEgrValue = outgoing or egress COS value
1.3.6.1.4.1.6296.101.28.1.2.9Integer32read-writecurrent
sleMlsQosGlobalControlQueueId
OBJECT-TYPE
Queue Id
1.3.6.1.4.1.6296.101.28.1.2.10INTEGERread-writecurrent
sleMlsQosGlobalControlWrrQueueWeight
OBJECT-TYPE
Queue weight for weighted round robin scheduling. This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId
1.3.6.1.4.1.6296.101.28.1.2.11INTEGERread-writecurrent
sleMlsQosGlobalControlCpuMaxPpsRate
OBJECT-TYPE
Rate limiting for CPU. Defines Max packets per second to CPU This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId
1.3.6.1.4.1.6296.101.28.1.2.12INTEGERread-writecurrent
sleMlsQosGlobalControlCpuQueueWt
OBJECT-TYPE
Weight for CPU Queue. This value is set for the Queue Id configured via sleMlsQosGlobalControlQueueId
1.3.6.1.4.1.6296.101.28.1.2.13INTEGERread-writecurrent
sleMlsQosGlobalControlNodeId
OBJECT-TYPE
Node Id
1.3.6.1.4.1.6296.101.28.1.2.14INTEGER (0..4)read-writecurrent
sleMlsQosGlobalControlMappingEgrClassValue
OBJECT-TYPE
Egress or outgoing mapping value is only for exp to class Diffserv class alias, eg: be, ef, af11 etc. If sleMlsQosGlobalControlMappingType is exp-to-class, this value has to be set. Ex. If sleMlsQosGlobalControlMappingType = exp-to-class, then sleMlsQosGlobalControlMappingEgrValue = outgoing or egress class value
1.3.6.1.4.1.6296.101.28.1.2.15OCTET STRINGread-writecurrent
sleMlsQosAggPolice
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.2
sleMlsQosAggPoliceTable
OBJECT-TYPE
Aggrgegate Policy Table
1.3.6.1.4.1.6296.101.28.2.1not-accessiblecurrent
sleMlsQosAggPoliceEntry
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.2.1.1not-accessiblecurrent
sleMlsQosAggPoliceIndex
OBJECT-TYPE
Police index
1.3.6.1.4.1.6296.101.28.2.1.1.1Integer32 (1..65535)not-accessiblecurrent
sleMlsQosAggPoliceName
OBJECT-TYPE
Police Name
1.3.6.1.4.1.6296.101.28.2.1.1.2OCTET STRINGread-onlycurrent
sleMlsQosAggPoliceTrafficRate
OBJECT-TYPE
Traffic Rate configured for the Aggregate police profile
1.3.6.1.4.1.6296.101.28.2.1.1.3Integer32read-onlycurrent
sleMlsQosAggPoliceBurstSize
OBJECT-TYPE
Burst Size configured for the Aggregate police profile
1.3.6.1.4.1.6296.101.28.2.1.1.4Integer32read-onlycurrent
sleMlsQosAggPoliceControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.2.2
sleMlsQosAggPoliceCtrlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.2.2.1INTEGER {createAggrPolice(1), deleteAggrPolice(2)}read-writecurrent
sleMlsQosAggPoliceCtrlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.2.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosAggPoliceConfigCtrlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.2.2.3Gauge32read-writecurrent
sleMlsQosAggPoliceCtrlTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.2.2.4TimeTicksread-onlycurrent
sleMlsQosAggPoliceCtrlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.2.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosAggPoliceCtrlName
OBJECT-TYPE
Aggregator Police Name
1.3.6.1.4.1.6296.101.28.2.2.6OCTET STRINGread-writecurrent
sleMlsQosAggPoliceCtrlTrafficRate
OBJECT-TYPE
Traffic Rate configured for the Aggrgegate Police profile
1.3.6.1.4.1.6296.101.28.2.2.7Integer32read-writecurrent
sleMlsQosAggPoliceCtrlBurstSize
OBJECT-TYPE
Traffic Rate configured for the Aggrgegate Police profile
1.3.6.1.4.1.6296.101.28.2.2.8Integer32read-writecurrent
sleMlsQosACL
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.3
sleMlsQosACLTable
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.3.1not-accessiblecurrent
sleMlsQosACLEntry
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.3.1.1not-accessiblecurrent
sleMlsQosACLIndex
OBJECT-TYPE
Index for the table. This is a running index number, which will be generated internally
1.3.6.1.4.1.6296.101.28.3.1.1.1Integer32 (1..65535)not-accessiblecurrent
sleMlsQosACLFilterIndex
OBJECT-TYPE
Filter Index for the table. This is a running index number, which will be generated internally
1.3.6.1.4.1.6296.101.28.3.1.1.2Integer32 (1..65535)not-accessiblecurrent
sleMlsQosACLName
OBJECT-TYPE
Access Control List Num. <1-99> standard access list <100-199> extended access list <1300-1999> standard access list (expanded range) <2000-2699> extended access list (expanded range) <WORD> Name of the access list
1.3.6.1.4.1.6296.101.28.3.1.1.3OCTET STRINGread-onlycurrent
sleMlsQosACLMatchType
OBJECT-TYPE
ACL MATCH Type mac (1), EthType(2), l3Proto (3)
1.3.6.1.4.1.6296.101.28.3.1.1.4ACLMatchTyperead-onlycurrent
sleMlsQosACLMatchAction
OBJECT-TYPE
ACL Actions deny(0) deny the packets permit(1) permit. remark(2) mark the packets
1.3.6.1.4.1.6296.101.28.3.1.1.5ACLMatchActionTyperead-onlycurrent
sleMlsQosACLEtherType
OBJECT-TYPE
ACL ethertype to be matched. ip4(0) ipv4 packets ip6(1) ipv6 packets. mpls(3) mpls packets
1.3.6.1.4.1.6296.101.28.3.1.1.6ACLEtherTyperead-onlycurrent
sleMlsQosACLL3Protocol
OBJECT-TYPE
ACL protocols to be matched. 0-255 : IANA protocol numbers 256 - any Some important protocol Numbers GRE - 47 IGMP -2 IPV4 - 4 IPComp - 108 OSPF - 89 RSVP - 46 PIM - 103 VRRP - 112
1.3.6.1.4.1.6296.101.28.3.1.1.7Integer32 (0..256)read-onlycurrent
sleMlsQosACLSrcIpAddress
OBJECT-TYPE
Src Ip Address
1.3.6.1.4.1.6296.101.28.3.1.1.8OCTET STRINGread-onlycurrent
sleMlsQosACLDstIpAddress
OBJECT-TYPE
DST Address
1.3.6.1.4.1.6296.101.28.3.1.1.9OCTET STRINGread-onlycurrent
sleMlsQosACLSrcIpAddrMask
OBJECT-TYPE
SRC Address Mask
1.3.6.1.4.1.6296.101.28.3.1.1.10OCTET STRINGread-onlycurrent
sleMlsQosACLDstIpAddrMask
OBJECT-TYPE
DST Address Mask
1.3.6.1.4.1.6296.101.28.3.1.1.11OCTET STRINGread-onlycurrent
sleMlsQosACLSrcMacAddress
OBJECT-TYPE
Src MAC Address
1.3.6.1.4.1.6296.101.28.3.1.1.12OCTET STRINGread-onlycurrent
sleMlsQosACLDstMacAddress
OBJECT-TYPE
DST MAC Address
1.3.6.1.4.1.6296.101.28.3.1.1.13OCTET STRINGread-onlycurrent
sleMlsQosACLSrcMacAddrMask
OBJECT-TYPE
SRC Address Mask
1.3.6.1.4.1.6296.101.28.3.1.1.14OCTET STRINGread-onlycurrent
sleMlsQosACLDstMacAddrMask
OBJECT-TYPE
DST Address Mask
1.3.6.1.4.1.6296.101.28.3.1.1.15OCTET STRINGread-onlycurrent
sleMlsQosACLTcpUdpSrcPortAction
OBJECT-TYPE
TCP/UDP Src port action 0 - no-action 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range
1.3.6.1.4.1.6296.101.28.3.1.1.16AclTcpUdpPortActionTyperead-onlycurrent
sleMlsQosACLTcpUdpDstPortAction
OBJECT-TYPE
TCP/UDP Dst port action 0 - no-action 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range
1.3.6.1.4.1.6296.101.28.3.1.1.17AclTcpUdpPortActionTyperead-onlycurrent
sleMlsQosACLTcpUdpSrcPort
OBJECT-TYPE
TCP/UDP Src port .
1.3.6.1.4.1.6296.101.28.3.1.1.18Integer32read-onlycurrent
sleMlsQosACLTcpUdpDstPort
OBJECT-TYPE
TCP/UDP Dst port .
1.3.6.1.4.1.6296.101.28.3.1.1.19Integer32read-onlycurrent
sleMlsQosACLNameSrcIpExactMatch
OBJECT-TYPE
Exact Match
1.3.6.1.4.1.6296.101.28.3.1.1.20Integer32read-onlycurrent
sleMlsQosACLActionRemarkDesc
OBJECT-TYPE
Remark Description
1.3.6.1.4.1.6296.101.28.3.1.1.21OCTET STRINGread-onlycurrent
sleMlsQosACLIcmpType
OBJECT-TYPE
The object is used to display the ICMP type of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1
1.3.6.1.4.1.6296.101.28.3.1.1.22Integer32read-onlycurrent
sleMlsQosACLIcmpCode
OBJECT-TYPE
The object is used to display the ICMP code of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1
1.3.6.1.4.1.6296.101.28.3.1.1.23Integer32read-onlycurrent
sleMlsQosACLTcpUdpSrcPortEnd
OBJECT-TYPE
End port for TCP/UDP source port range.
1.3.6.1.4.1.6296.101.28.3.1.1.24Integer32read-onlycurrent
sleMlsQosACLTcpUdpDstPortEnd
OBJECT-TYPE
End port for TCP/UDP destination port range.
1.3.6.1.4.1.6296.101.28.3.1.1.25Integer32read-onlycurrent
sleMlsQosACLControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.3.2
sleMlsQosACLControlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.3.2.1INTEGER {setStandAclMatchSrcIp(1), unSetStandAclMatchSrcIp(2), setExtenAclMatchMac(3), unSetExtenAclMatchMac(4), setExtenAclMatchEthType(5), unSetExtenAclMatchEthType(6), setExtenAclMatchL3Proto(7), unSetExtenAclMatchL3Proto(8), setExtenAclMatchTcpUdp(9), unSetExtenAclMatchTcpUdp(10), setAclNameSrcIp(11), unSetAclNameSrcIp(12), setAclWithActionRemark(13), unSetAclWithActionRemark(14)}read-writecurrent
sleMlsQosACLControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.3.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosACLConfigControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.3.2.3Gauge32read-writecurrent
sleMlsQosACLControlTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.3.2.4TimeTicksread-onlycurrent
sleMlsQosACLControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.3.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosACLCtrlName
OBJECT-TYPE
Access Control List Name. <1-99> standard access list <100-199> extended access list <1300-1999> standard access list (expanded range) <2000-2699> extended access list (expanded range) <word> Name for the access list
1.3.6.1.4.1.6296.101.28.3.2.6OCTET STRINGread-writecurrent
sleMlsQosACLCtrlMatchType
OBJECT-TYPE
ACL Match Types mac (1), EthType(2), l3Proto (3)
1.3.6.1.4.1.6296.101.28.3.2.7ACLMatchTyperead-writecurrent
sleMlsQosACLCtrlMatchAction
OBJECT-TYPE
ACL Actions deny(0) deny the packets permit(1) Permit packets remark(2) mark the packets
1.3.6.1.4.1.6296.101.28.3.2.8ACLMatchActionTyperead-writecurrent
sleMlsQosACLCtrlEtherType
OBJECT-TYPE
ACL MAC ethertype to be matched. WORD Ethertype value - (0x600-0xffff) ip4 IPv4 Ethertype - 0x0800 ip6 IPv6 Ethertype - 0x86dd mpls MPLS Ethertype - 0x8847
1.3.6.1.4.1.6296.101.28.3.2.9ACLEtherTyperead-writecurrent
sleMlsQosACLCtrlL3Protocol
OBJECT-TYPE
ACL protocols to be matched. 0-255 : IANA protocol numbers 256 - any Some important protocol Numbers GRE - 47 IGMP -2 IPV4 - 4 IPComp - 108 OSPF - 89 RSVP - 46 PIM - 103 VRRP - 112
1.3.6.1.4.1.6296.101.28.3.2.10Integer32 (0..256)read-writecurrent
sleMlsQosACLCtrlSrcAddress
OBJECT-TYPE
ACL SrcAddress. 1. MAC address 2. IP Address 3. Any
1.3.6.1.4.1.6296.101.28.3.2.11OCTET STRINGread-writecurrent
sleMlsQosACLCtrlDstAddress
OBJECT-TYPE
ACL SrcAddress. 1. MAC address 2. IP Address 3. Any
1.3.6.1.4.1.6296.101.28.3.2.12OCTET STRINGread-writecurrent
sleMlsQosACLCtrlSrcAddrMask
OBJECT-TYPE
ACL Src Addr Mask. 1. MAC address 2. IP Address
1.3.6.1.4.1.6296.101.28.3.2.13OCTET STRINGread-writecurrent
sleMlsQosACLCtrlDstAddrMask
OBJECT-TYPE
ACL dst Addr Mask. 1. MAC address 2. IP Address
1.3.6.1.4.1.6296.101.28.3.2.14OCTET STRINGread-writecurrent
sleMlsQosACLCtrlTcpUdpSrcPortAction
OBJECT-TYPE
TCP/UDP Port Action to be matched. 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range
1.3.6.1.4.1.6296.101.28.3.2.15AclTcpUdpPortActionTyperead-writecurrent
sleMlsQosACLCtrlTcpUdpDstPortAction
OBJECT-TYPE
TCP/UDP Port Action to be matched. 1 - equal 2 - not-equal 3 - less-than 4 - Greater-than 5 - Range
1.3.6.1.4.1.6296.101.28.3.2.16AclTcpUdpPortActionTyperead-writecurrent
sleMlsQosACLCtrlTcpUdpSrcPort
OBJECT-TYPE
TCP/UDP Src port to be matched.
1.3.6.1.4.1.6296.101.28.3.2.17Integer32read-writecurrent
sleMlsQosACLCtrlTcpUdpDstPort
OBJECT-TYPE
TCP/UDP Dst port to be matched.
1.3.6.1.4.1.6296.101.28.3.2.18Integer32read-writecurrent
sleMlsQosACLCtrlAclNameExactMatch
OBJECT-TYPE
Configure Exact Match for Name
1.3.6.1.4.1.6296.101.28.3.2.19Integer32read-writecurrent
sleMlsQosACLCtrlActionRemarkDesc
OBJECT-TYPE
Configure remark description
1.3.6.1.4.1.6296.101.28.3.2.20OCTET STRINGread-writecurrent
sleMlsQosACLCtrlIcmpType
OBJECT-TYPE
The object is used to set the ICMP type of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1
1.3.6.1.4.1.6296.101.28.3.2.21Integer32read-writecurrent
sleMlsQosACLCtrlIcmpCode
OBJECT-TYPE
The object is used to set the ICMP code of control message Description Type Code echo-reply 0 0 net-unreachable 3 0 host-unreachable 3 1 protocol-unreachable 3 2 port-unreachable 3 3 packet-too-big 3 4 source-route-failed 3 5 network-unknown 3 6 host-unknown 3 7 host-isolated 3 8 dod-net-prohibited 3 9 dod-host-prohibited 3 10 net-tos-unreachable 3 11 host-tos-unreachable 3 12 administratively-prohibited 3 13 host-precedence-unreachable 3 14 precedence-unreachable 3 15 source-quench 4 0 net-redirect 5 0 host-redirect 5 1 net-tos-redirect 5 2 host-tos-redirect 5 3 alternate-address 6 -1 echo 8 0 router-advertisement 9 0 router-solicitation 10 0 time-exceeded 11 -1 ttl-exceeded 11 0 reassembly-timeout 11 1 parameter-problem 12 -1 no-room-for-option 12 0 option-missing 12 1 timestamp-request 13 0 timestamp-reply 14 0 information-request 15 0 information-reply 16 0 mask-request 17 0 mask-reply 18 0 traceroute 30 -1 conversion-error 31 -1 mobile-redirect 32 -1
1.3.6.1.4.1.6296.101.28.3.2.22Integer32read-writecurrent
sleMlsQosACLCtrlTcpUdpSrcPortEnd
OBJECT-TYPE
End port for TCP/UDP Src port range to be matched.
1.3.6.1.4.1.6296.101.28.3.2.23Integer32read-writecurrent
sleMlsQosACLCtrlTcpUdpDstPortEnd
OBJECT-TYPE
End port for TCP/UDP Dst port range to be matched.
1.3.6.1.4.1.6296.101.28.3.2.24Integer32read-writecurrent
sleMlsQosACLNotification
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.3.3
sleMlsQosClassMap
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.4
sleMlsQosClassMapTable
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.4.1not-accessiblecurrent
sleMlsQosClassMapEntry
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.4.1.1not-accessiblecurrent
sleMlsQosClassMapName
OBJECT-TYPE
Index for the table. Class Map name
1.3.6.1.4.1.6296.101.28.4.1.1.1OCTET STRINGnot-accessiblecurrent
sleMlsQosClassMapMatchCosValue
OBJECT-TYPE
Class map Match criteria : Cos value
1.3.6.1.4.1.6296.101.28.4.1.1.2Integer32read-onlycurrent
sleMlsQosClassMapMatchInnerCosValue
OBJECT-TYPE
Class map Match criteria : Inner Cos value
1.3.6.1.4.1.6296.101.28.4.1.1.3Integer32read-onlycurrent
sleMlsQosClassMapMatchEgressInterface
OBJECT-TYPE
Class map Match criteria : Engress Interface
1.3.6.1.4.1.6296.101.28.4.1.1.4OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchEtherType
OBJECT-TYPE
Class map Match criteria : Eth Type
1.3.6.1.4.1.6296.101.28.4.1.1.5OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchSrcIpAddr
OBJECT-TYPE
Class map Match criteria : Src Ip Address
1.3.6.1.4.1.6296.101.28.4.1.1.6OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchDstIpAddr
OBJECT-TYPE
Class map Match criteria : dst Ip Address
1.3.6.1.4.1.6296.101.28.4.1.1.7OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchSrcIpMaskLen
OBJECT-TYPE
Class map Match criteria : Src Ip Mask Length
1.3.6.1.4.1.6296.101.28.4.1.1.8Integer32read-onlycurrent
sleMlsQosClassMapMatchDstIpMaskLen
OBJECT-TYPE
Class map Match criteria : Dst Ip Mask Length
1.3.6.1.4.1.6296.101.28.4.1.1.9Integer32read-onlycurrent
sleMlsQosClassMapMatchSrcIpV6Addr
OBJECT-TYPE
Class map Match criteria : Src Ip Address
1.3.6.1.4.1.6296.101.28.4.1.1.10OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchDstIpV6Addr
OBJECT-TYPE
Class map Match criteria : dst Ip Address
1.3.6.1.4.1.6296.101.28.4.1.1.11OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchSrcIpV6MaskLen
OBJECT-TYPE
Class map Match criteria : Src Ip Mask Length
1.3.6.1.4.1.6296.101.28.4.1.1.12Integer32read-onlycurrent
sleMlsQosClassMapMatchDstIpV6MaskLen
OBJECT-TYPE
Class map Match criteria : Dst Ip Mask Length
1.3.6.1.4.1.6296.101.28.4.1.1.13Integer32read-onlycurrent
sleMlsQosClassMapMatchIpDscp
OBJECT-TYPE
Class map Match criteria : DSCP value
1.3.6.1.4.1.6296.101.28.4.1.1.14Integer32read-onlycurrent
sleMlsQosClassMapMatchIpPrecedence
OBJECT-TYPE
Class map Match criteria : Ip Precedence
1.3.6.1.4.1.6296.101.28.4.1.1.15Integer32read-onlycurrent
sleMlsQosClassMapMatchIp6Dscp
OBJECT-TYPE
Class map Match criteria : Ip6 DSCP value
1.3.6.1.4.1.6296.101.28.4.1.1.16Integer32read-onlycurrent
sleMlsQosClassMapMatchIp6Precedence
OBJECT-TYPE
Class map Match criteria : ip6 Precedence value
1.3.6.1.4.1.6296.101.28.4.1.1.17Integer32read-onlycurrent
sleMlsQosClassMapMatchTcpSrcPort
OBJECT-TYPE
Class map Match criteria : TCP src Port
1.3.6.1.4.1.6296.101.28.4.1.1.18OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchTcpDstPort
OBJECT-TYPE
Class map Match criteria : TCP Dst Port
1.3.6.1.4.1.6296.101.28.4.1.1.19OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchTcpSrcPortRange
OBJECT-TYPE
Class map Match criteria : TCP src Port Range
1.3.6.1.4.1.6296.101.28.4.1.1.20OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchTcpDstPortRange
OBJECT-TYPE
Class map Match criteria : TCP Dst Port Range
1.3.6.1.4.1.6296.101.28.4.1.1.21OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchUdpSrcPort
OBJECT-TYPE
Class map Match criteria : UDP src Port
1.3.6.1.4.1.6296.101.28.4.1.1.22OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchUdpDstPort
OBJECT-TYPE
Class map Match criteria : UDP Dst Port
1.3.6.1.4.1.6296.101.28.4.1.1.23OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchUdpSrcPortRange
OBJECT-TYPE
Class map Match criteria : UDP src Port
1.3.6.1.4.1.6296.101.28.4.1.1.24OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchUdpDstPortRange
OBJECT-TYPE
Class map Match criteria : UDP Dst Port
1.3.6.1.4.1.6296.101.28.4.1.1.25OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchSrcMacAddr
OBJECT-TYPE
Class map Match criteria : Src MAC Addr
1.3.6.1.4.1.6296.101.28.4.1.1.26OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchSrcMacMask
OBJECT-TYPE
Class map Match criteria : Src MAC Addr Mask
1.3.6.1.4.1.6296.101.28.4.1.1.27OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchDstMacAddr
OBJECT-TYPE
Class map Match criteria : Dst MAC Addr
1.3.6.1.4.1.6296.101.28.4.1.1.28OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchDstMacMask
OBJECT-TYPE
Class map Match criteria : Dst MAC Addr Mask
1.3.6.1.4.1.6296.101.28.4.1.1.29OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchVlanId
OBJECT-TYPE
Class map Match criteria : Vlan Id
1.3.6.1.4.1.6296.101.28.4.1.1.30OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchVlanIdRange
OBJECT-TYPE
Class map Match criteria : Vlan Id Range
1.3.6.1.4.1.6296.101.28.4.1.1.31OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchInnerVlanId
OBJECT-TYPE
Class map Match criteria : Inner Vlan Id
1.3.6.1.4.1.6296.101.28.4.1.1.32Integer32read-onlycurrent
sleMlsQosClassMapMatchVlanTpid
OBJECT-TYPE
Class map Match criteria : Vlan TPID
1.3.6.1.4.1.6296.101.28.4.1.1.33OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchAccessGroup
OBJECT-TYPE
Class map Match criteria : Acl Name
1.3.6.1.4.1.6296.101.28.4.1.1.34OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchLayer4SrcPort
OBJECT-TYPE
Class map Match criteria : Layer4 Any Src Port
1.3.6.1.4.1.6296.101.28.4.1.1.35OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchLayer4DstPort
OBJECT-TYPE
Class map Match criteria : Layer4 Any Dst Port
1.3.6.1.4.1.6296.101.28.4.1.1.36OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchLayer4SrcPortRange
OBJECT-TYPE
Class map Match criteria : Layer4 Any src Port range
1.3.6.1.4.1.6296.101.28.4.1.1.37OCTET STRINGread-onlycurrent
sleMlsQosClassMapMatchLayer4DstPortRange
OBJECT-TYPE
Class map Match criteria : Layer4 Any Dst Port range
1.3.6.1.4.1.6296.101.28.4.1.1.38OCTET STRINGread-onlycurrent
sleMplsQosClassMapMatchCriteria
OBJECT-TYPE
This object is used to set the Class map match criteria, to map the matchAll or MatchAny for HQS.
1.3.6.1.4.1.6296.101.28.4.1.1.39INTEGER {noMatch(0), matchAll(1), matchAny(2)}read-writecurrent
sleMlsQosClassMapControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.4.2
sleMlsQosClassMapControlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.4.2.1INTEGER {createClassMap(1), deleteClassMap(2), setClassMapMatch(3), unSetClassMapMatch(4), setClassMapMatchRange(5), unSetClassMapMatchRange(6), setClassMapMatchEtherType(7), unSetClassMapMatchEtherType(8), setClassMapMatchIpAddr(9), unSetClassMapMatchIpAddr(10), setClassMapMatchMac(11), unSetClassMapMatchMac(12), setClassMapMatchVlanTpid(13), unSetClassMapMatchVlanTpid(14), setClassMapMatchAccessGroup(15), unSetClassMapMatchAccessGroup(16), setClassMapMatchEgressIntf(17), unSetClassMapMatchEgressIntf(18)}read-writecurrent
sleMlsQosClassMapControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.4.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosClassMapControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.4.2.3Gauge32read-writecurrent
sleMlsQosClassMapontrolTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.4.2.4TimeTicksread-onlycurrent
sleMlsQosClassMapControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.4.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosClassMapCtrlName
OBJECT-TYPE
Class Map name
1.3.6.1.4.1.6296.101.28.4.2.6OCTET STRINGread-writecurrent
sleMlsQosClassMapCtrlMatchType
OBJECT-TYPE
Class Map Type cos (1) , innerCos(2), ipDscp (3), ipPrecedence (4), ip6Dscp (5), ip6Precedence (6), tcpSrcPort (7), tcpDstPort (8), udpSrcPort (9), udpDstPort (10), VlanId (11), innerVlanId (12), layer4SrcPort (13), layer4DstPort (14)
1.3.6.1.4.1.6296.101.28.4.2.7ClassMapMatchTyperead-writecurrent
sleMlsQosClassMapCtrlMatchVal
OBJECT-TYPE
Class Map match Value
1.3.6.1.4.1.6296.101.28.4.2.8Integer32read-writecurrent
sleMlsQosClassMapCtrlMatchRangeType
OBJECT-TYPE
Class Map Type tcpSrcPort (1), tcpDstPort (2), udpSrcPort (3), udpDstPort (4), VlanId (5), layer4SrcPort (6), layer4DstPort (7)
1.3.6.1.4.1.6296.101.28.4.2.9ClassMapMatchRangeTyperead-writecurrent
sleMlsQosClassMapCtrlMatchRangeLow
OBJECT-TYPE
Class Map match Value: Low
1.3.6.1.4.1.6296.101.28.4.2.10Integer32read-writecurrent
sleMlsQosClassMapCtrlMatchRangeHigh
OBJECT-TYPE
Class Map match Value : High
1.3.6.1.4.1.6296.101.28.4.2.11Integer32read-writecurrent
sleMlsQosClassMapCtrlMatchEtherType
OBJECT-TYPE
Class map Match criteria : Eth Type
1.3.6.1.4.1.6296.101.28.4.2.12OCTET STRINGread-writecurrent
sleMlsQosClassMapCtrlMatchSrcType
OBJECT-TYPE
Class Map Src Type 1. IPv4 2. IPv6 3. Mac
1.3.6.1.4.1.6296.101.28.4.2.13INTEGER {ipv4(1), ipv6(2), mac(3)}read-writecurrent
sleMlsQosClassMapCtrlMatchSrcAddr
OBJECT-TYPE
Class map Match criteria : Src Address. It can be IPV4 / IPV6 / MAC
1.3.6.1.4.1.6296.101.28.4.2.14OCTET STRINGread-writecurrent
sleMlsQosClassMapCtrlMatchDstAddr
OBJECT-TYPE
Class map Match criteria : dst Ip Address it can be IPV4 / IPV6 / MAC
1.3.6.1.4.1.6296.101.28.4.2.15OCTET STRINGread-writecurrent
sleMlsQosClassMapCtrlMatchSrcIpMaskLen
OBJECT-TYPE
Class map Match criteria : Src Ip Mask Length
1.3.6.1.4.1.6296.101.28.4.2.16Integer32read-writecurrent
sleMlsQosClassMapCtrlMatchDstIpMaskLen
OBJECT-TYPE
Class map Match criteria : Dst Ip Mask Length
1.3.6.1.4.1.6296.101.28.4.2.17Integer32read-writecurrent
sleMlsQosClassMapCtrlMatchSrcMacMask
OBJECT-TYPE
Class map Match criteria : Src MAC Addr Mask
1.3.6.1.4.1.6296.101.28.4.2.18OCTET STRINGread-writecurrent
sleMlsQosClassMapCtrlMatchDstMacMask
OBJECT-TYPE
Class map Match criteria : Dst MAC Addr Mask
1.3.6.1.4.1.6296.101.28.4.2.19OCTET STRINGread-writecurrent
sleMlsQosClassMapCtrlMatchAcessGroup
OBJECT-TYPE
Class map Match criteria : ACL Group List
1.3.6.1.4.1.6296.101.28.4.2.20OCTET STRINGread-writecurrent
sleMlsQosClassMapCtrlMatchVlanTpid
OBJECT-TYPE
Class map Match criteria : vlan TDID
1.3.6.1.4.1.6296.101.28.4.2.21OCTET STRINGread-writecurrent
sleMlsQosClassMapCtrlMatchEgressInterface
OBJECT-TYPE
Class map Match criteria : egress interface. This can be CPU, interface Name, Vlan Interface
1.3.6.1.4.1.6296.101.28.4.2.22OCTET STRINGread-writecurrent
sleMplsQosClassMapCtrlMatchCriteria
OBJECT-TYPE
This object is used to set the Class map match criteria, to map the matchAll or MatchAny for HQS.
1.3.6.1.4.1.6296.101.28.4.2.23INTEGER {matchAll(1), matchAny(2)}read-writecurrent
sleMlsQosClassMapNotification
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.4.3
sleMlsQosPolicyMap
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.5
sleMlsQosPolicyMapTable
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.5.1not-accessiblecurrent
sleMlsQosPolicyMapEntry
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.5.1.1not-accessiblecurrent
sleMlsQosPmapName
OBJECT-TYPE
Policy Map name
1.3.6.1.4.1.6296.101.28.5.1.1.1OCTET STRINGread-onlycurrent
sleMlsQosPmapClassName
OBJECT-TYPE
Class map Name
1.3.6.1.4.1.6296.101.28.5.1.1.2OCTET STRINGread-onlycurrent
sleMlsQosPmapClassMatchPriority
OBJECT-TYPE
Priority low(0) medium(1) high(2) highest(3)
1.3.6.1.4.1.6296.101.28.5.1.1.3PmapPriorityTyperead-onlycurrent
sleMlsQosPmapClassOperMode
OBJECT-TYPE
Operation Mode
1.3.6.1.4.1.6296.101.28.5.1.1.4INTEGER {none(0), allow(1), deny(2)}read-onlycurrent
sleMlsQosPmapClassPoliceType
OBJECT-TYPE
Police Type srtcm(1) trtcm(2)
1.3.6.1.4.1.6296.101.28.5.1.1.5PmapPoliceTyperead-onlycurrent
sleMlsQosPmapClassPoliceCIR
OBJECT-TYPE
Police CIR (committed ingress rate) value
1.3.6.1.4.1.6296.101.28.5.1.1.6Integer32read-onlycurrent
sleMlsQosPmapClassPolicePIR
OBJECT-TYPE
Police PIR (peak ingress rate) value
1.3.6.1.4.1.6296.101.28.5.1.1.7Integer32read-onlycurrent
sleMlsQosPmapClassPoliceCBS
OBJECT-TYPE
Police CBS (committed burst size) value
1.3.6.1.4.1.6296.101.28.5.1.1.8Integer32read-onlycurrent
sleMlsQosPmapClassPoliceEBS
OBJECT-TYPE
Police EBS (Excess burst size) value
1.3.6.1.4.1.6296.101.28.5.1.1.9Integer32read-onlycurrent
sleMlsQosPmapClassPoliceExdAction
OBJECT-TYPE
Exceed Action Type none (0) drop (1) set-dscp-transmit (2) set-tos-transmit (3) set-cos-transmit (4) transmit (7)
1.3.6.1.4.1.6296.101.28.5.1.1.10PmapExceedActionTyperead-onlycurrent
sleMlsQosPmapClassPoliceExdActionCos
OBJECT-TYPE
Exceed Action COS
1.3.6.1.4.1.6296.101.28.5.1.1.11Integer32read-onlycurrent
sleMlsQosPmapClassPoliceExdActionDscp
OBJECT-TYPE
Exceed Action DSCP
1.3.6.1.4.1.6296.101.28.5.1.1.12Integer32read-onlycurrent
sleMlsQosPmapClassPoliceExdActionTos
OBJECT-TYPE
Exceed Action TOS
1.3.6.1.4.1.6296.101.28.5.1.1.13Integer32read-onlycurrent
sleMlsQosPmapClassPoliceExdActionViolateAction
OBJECT-TYPE
Violate Action Type none(0) drop(1) set-dscp-transmit(2) set-cos-transmit(3) set-tos-transmit(4) transmit(5)
1.3.6.1.4.1.6296.101.28.5.1.1.14PmapViolateActionTyperead-onlycurrent
sleMlsQosPmapClassPoliceExdActionViolateValue
OBJECT-TYPE
Violate Action Value
1.3.6.1.4.1.6296.101.28.5.1.1.15Integer32read-onlycurrent
sleMlsQosPmapClassPoliceAggregateName
OBJECT-TYPE
Agrregate Police name:
1.3.6.1.4.1.6296.101.28.5.1.1.16OCTET STRINGread-onlycurrent
sleMlsQosPmapClassSetActionDeny
OBJECT-TYPE
Action Type: deny
1.3.6.1.4.1.6296.101.28.5.1.1.17Integer32read-onlycurrent
sleMlsQosPmapClassSetActionCos
OBJECT-TYPE
Cos value
1.3.6.1.4.1.6296.101.28.5.1.1.18Integer32read-onlycurrent
sleMlsQosPmapClassSetActionCpuCos
OBJECT-TYPE
cpy Cos value.
1.3.6.1.4.1.6296.101.28.5.1.1.19Integer32read-onlycurrent
sleMlsQosPmapClassSetActionIpDscp
OBJECT-TYPE
Ip DSCP value .
1.3.6.1.4.1.6296.101.28.5.1.1.20Integer32read-onlycurrent
sleMlsQosPmapClassSetActionIp6Dscp
OBJECT-TYPE
Ip6 DSCP value to be set.
1.3.6.1.4.1.6296.101.28.5.1.1.21Integer32read-onlycurrent
sleMlsQosPmapClassSetActionIpPrecedence
OBJECT-TYPE
Ip precedence value to be set.
1.3.6.1.4.1.6296.101.28.5.1.1.22Integer32read-onlycurrent
sleMlsQosPmapClassSetActionIp6Precedence
OBJECT-TYPE
Ip6 precedence value to be set.
1.3.6.1.4.1.6296.101.28.5.1.1.23Integer32read-onlycurrent
sleMlsQosPmapClassSetActionMirrorToPortVal
OBJECT-TYPE
Mirror to Port value.
1.3.6.1.4.1.6296.101.28.5.1.1.24OCTET STRINGread-onlycurrent
sleMlsQosPmapClassSetActionRedirectToPortVal
OBJECT-TYPE
redirect to Port value.
1.3.6.1.4.1.6296.101.28.5.1.1.25OCTET STRINGread-onlycurrent
sleMlsQosPmapClassSetActionVlanId
OBJECT-TYPE
Vlan Id value.
1.3.6.1.4.1.6296.101.28.5.1.1.26Integer32read-onlycurrent
sleMlsQosPmapClassSetActionVlanCos
OBJECT-TYPE
Vlan COS value
1.3.6.1.4.1.6296.101.28.5.1.1.27Integer32read-onlycurrent
sleMlsQosPmapClassSetActionQosGroup
OBJECT-TYPE
Heirarchical qos policy-map qos-group. Max range is 1 to 2000.
1.3.6.1.4.1.6296.101.28.5.1.1.28INTEGERread-onlycurrent
sleMplsQosPmapClassSetActionQueue
OBJECT-TYPE
Internal Queue Priority.
1.3.6.1.4.1.6296.101.28.5.1.1.29INTEGER (0..7)read-onlycurrent
sleMplsQosPmapClassSetActionCopyCpu
OBJECT-TYPE
Copy to CPU.
1.3.6.1.4.1.6296.101.28.5.1.1.30INTEGERread-onlycurrent
sleMlsQosPolicyMapControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.5.2
sleMlsQosPolicyMapControlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.5.2.1INTEGER {createPolicyMapClass(1), deletePolicyMapClass(2), setPolicyMapClassMatchPriority(3), setPolicyMapClassOperMode(4), unSetPolicyMapClassOperMode(5), setPolicyMapClassPolicer(6), unSetPolicyMapClassPolicer(7), setPolicyMapClassPolicerAggregate(8), unSetPolicyMapClassPolicerAggregate(9), setPolicyMapClassSet(10), unSetPolicyMapClassSet(11), deletePolicyMap(12)}read-writecurrent
sleMlsQosPolicyMapControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.5.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosPolicyMapControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.5.2.3Gauge32read-writecurrent
sleMlsQosPolicyMapontrolTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.5.2.4TimeTicksread-onlycurrent
sleMlsQosPolicyMapControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.5.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosPolicyMapCtrlName
OBJECT-TYPE
Index for the table. Class Map name
1.3.6.1.4.1.6296.101.28.5.2.6OCTET STRINGread-writecurrent
sleMlsQosPolicyMapCtrlClassName
OBJECT-TYPE
Class map Name
1.3.6.1.4.1.6296.101.28.5.2.7OCTET STRINGread-writecurrent
sleMlsQosPolicyMapCtrlClassMatchPriority
OBJECT-TYPE
Priority low(0) medium(1) high(2) highest(3)
1.3.6.1.4.1.6296.101.28.5.2.8PmapPriorityTyperead-writecurrent
sleMlsQosPolicyMapCtrlClassOperMode
OBJECT-TYPE
Operation Mode
1.3.6.1.4.1.6296.101.28.5.2.9INTEGER {none(0), allow(1), deny(2)}read-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceType
OBJECT-TYPE
Police Type srtcm(1) trtcm(2)
1.3.6.1.4.1.6296.101.28.5.2.10PmapPoliceTyperead-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceCIR
OBJECT-TYPE
Police CIR (committed ingress rate) value
1.3.6.1.4.1.6296.101.28.5.2.11Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassPolicePIR
OBJECT-TYPE
Police PIR (Peak ingress rate) value
1.3.6.1.4.1.6296.101.28.5.2.12Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceCBS
OBJECT-TYPE
Police CBS (Committed Burst size) value
1.3.6.1.4.1.6296.101.28.5.2.13Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceEBS
OBJECT-TYPE
Police EBS (Excess Burst size) value
1.3.6.1.4.1.6296.101.28.5.2.14Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceExdAction
OBJECT-TYPE
Exceed Action Type none (0) drop (1) set-dscp-transmit (2) set-tos-transmit (3) set-cos-transmit (4) transmit (7)
1.3.6.1.4.1.6296.101.28.5.2.15PmapExceedActionTyperead-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceExdActionCos
OBJECT-TYPE
Exceed Action COS
1.3.6.1.4.1.6296.101.28.5.2.16Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceExdActionDscp
OBJECT-TYPE
Exceed Action DSCP
1.3.6.1.4.1.6296.101.28.5.2.17Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceExdActionTos
OBJECT-TYPE
Exceed Action TOS
1.3.6.1.4.1.6296.101.28.5.2.18Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceExdActionViolateAction
OBJECT-TYPE
Exceed Action Violate none(0) drop(1) set-dscp-transmit(2) set-cos-transmit(3) set-tos-transmit(4) transmit(5)
1.3.6.1.4.1.6296.101.28.5.2.19PmapViolateActionTyperead-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceExdActionViolateValue
OBJECT-TYPE
Exceed Action Violate Value
1.3.6.1.4.1.6296.101.28.5.2.20Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassPoliceAggregateName
OBJECT-TYPE
Aggregate Policy name: this is configured via sleMlsQosAggPoliceTable
1.3.6.1.4.1.6296.101.28.5.2.21OCTET STRINGread-writecurrent
sleMlsQosPolicyMapCtrlClassSetAction
OBJECT-TYPE
Action Types: cos (1), cpu-cos (2), ip-dscp (3), ip-precedence (4), redirect-to-port (5), mirror-to-port (6), vlan (7), ip6-dscp (8), ip6-precedence (9), cpu-copy (10), deny (11), qos-group(12), none(13), queue(14), vlan-cos(15)
1.3.6.1.4.1.6296.101.28.5.2.22PmapSetActionTyperead-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionCos
OBJECT-TYPE
Cos value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as cos
1.3.6.1.4.1.6296.101.28.5.2.23Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionCpuCos
OBJECT-TYPE
cpy Cos value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as cpu-cos
1.3.6.1.4.1.6296.101.28.5.2.24Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionIpDscp
OBJECT-TYPE
Ip DSCP value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip-dscp
1.3.6.1.4.1.6296.101.28.5.2.25Integer32read-onlycurrent
sleMlsQosPolicyMapCtrlClassSetActionIp6Dscp
OBJECT-TYPE
Ip6 DSCP value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip6-dscp
1.3.6.1.4.1.6296.101.28.5.2.26Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionIpPrecedence
OBJECT-TYPE
Ip precedence value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip-precedence
1.3.6.1.4.1.6296.101.28.5.2.27Integer32read-onlycurrent
sleMlsQosPolicyMapCtrlClassSetActionIp6Precedence
OBJECT-TYPE
Ip6 precedence value to be set. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as ip6-precedence
1.3.6.1.4.1.6296.101.28.5.2.28Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionMirrorToPort
OBJECT-TYPE
Mirror to Port value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To setthis value, sleMlsQosPolicyMapCtrlClassSetAction should be set as mirror-to-port
1.3.6.1.4.1.6296.101.28.5.2.29OCTET STRINGread-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionRedirectToPort
OBJECT-TYPE
redirect to Port value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To setthis value, sleMlsQosPolicyMapCtrlClassSetAction should be set as redirect-to-port
1.3.6.1.4.1.6296.101.28.5.2.30OCTET STRINGread-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionVlanId
OBJECT-TYPE
Vlan Id value. This object is dependent on sleMlsQosPolicyMapCtrlClassSetAction. To set this value, sleMlsQosPolicyMapCtrlClassSetAction should be set as vlan
1.3.6.1.4.1.6296.101.28.5.2.31Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionVlanCos
OBJECT-TYPE
Vlan COS value
1.3.6.1.4.1.6296.101.28.5.2.32Integer32read-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionQosGroup
OBJECT-TYPE
Heirarchical qos policy-map qos-group. Max range is 1 to 2000.
1.3.6.1.4.1.6296.101.28.5.2.33INTEGERread-writecurrent
sleMlsQosPolicyMapCtrlClassSetActionQueue
OBJECT-TYPE
Internal Queue Priority.
1.3.6.1.4.1.6296.101.28.5.2.34INTEGER (0..7)read-writecurrent
sleMlsQosInterface
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.6
sleMlsQosInterfaceTable
OBJECT-TYPE
Interface table
1.3.6.1.4.1.6296.101.28.6.1not-accessiblecurrent
sleMlsQosInterfaceEntry
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.6.1.1not-accessiblecurrent
sleMlsQosInterfaceIndex
OBJECT-TYPE
This Index is based on Max entries i.e. 64 (dscp)
1.3.6.1.4.1.6296.101.28.6.1.1.1Integer32 (1..64)not-accessiblecurrent
sleMlsQosInterfaceName
OBJECT-TYPE
Index for the table. Interface Name
1.3.6.1.4.1.6296.101.28.6.1.1.2OCTET STRINGread-onlycurrent
sleMlsQosInterfaceTrustState
OBJECT-TYPE
Interface trust state none (0) cos (1) dscp (2)
1.3.6.1.4.1.6296.101.28.6.1.1.3MlsQosIntfTrustStateread-onlycurrent
sleMlsQosInterfaceCos
OBJECT-TYPE
Interface Cos value
1.3.6.1.4.1.6296.101.28.6.1.1.4Integer32read-onlycurrent
sleMlsQosInterfaceCosOverride
OBJECT-TYPE
Interface Cos override value
1.3.6.1.4.1.6296.101.28.6.1.1.5Integer32read-onlycurrent
sleMlsQosInterfaceCosToCos
OBJECT-TYPE
Interface Cos to cos mapping
1.3.6.1.4.1.6296.101.28.6.1.1.6OCTET STRINGread-onlycurrent
sleMlsQosInterfaceCosToQueue
OBJECT-TYPE
Interface Cos to queue mapping
1.3.6.1.4.1.6296.101.28.6.1.1.7OCTET STRINGread-onlycurrent
sleMlsQosInterfaceDscp
OBJECT-TYPE
Interface DSCP values
1.3.6.1.4.1.6296.101.28.6.1.1.8Integer32read-onlycurrent
sleMlsQosInterfaceDscpToDscp
OBJECT-TYPE
Interface dscp to dscp mapping
1.3.6.1.4.1.6296.101.28.6.1.1.9OCTET STRINGread-onlycurrent
sleMlsQosInterfaceDscpToQueue
OBJECT-TYPE
Interface dscp to queue mapping
1.3.6.1.4.1.6296.101.28.6.1.1.10OCTET STRINGread-onlycurrent
sleMlsQosInterfaceExpToExp
OBJECT-TYPE
Interface exp to exp mapping
1.3.6.1.4.1.6296.101.28.6.1.1.11OCTET STRINGread-onlycurrent
sleMlsQosInterfaceTrafficShapeRate
OBJECT-TYPE
Interface Traffic Shaping rate
1.3.6.1.4.1.6296.101.28.6.1.1.12Integer32read-onlycurrent
sleMlsQosInterfaceTrafficShapeBurst
OBJECT-TYPE
Interface traffic shaping burst
1.3.6.1.4.1.6296.101.28.6.1.1.13Integer32read-onlycurrent
sleMlsQosInterfaceInputPolicyMap
OBJECT-TYPE
Interface policy map mapping
1.3.6.1.4.1.6296.101.28.6.1.1.14OCTET STRINGread-onlycurrent
sleMlsQosInterfaceOutputPolicyMap
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.6.1.1.15OCTET STRINGread-onlycurrent
sleMlsQosInterfaceTrustPassthroughCos
OBJECT-TYPE
Interface trust pass-through COS enabled
1.3.6.1.4.1.6296.101.28.6.1.1.16Integer32read-onlycurrent
sleMlsQosInterfaceTrustPassthroughDscp
OBJECT-TYPE
Interface trust pass-through DSCP enabled
1.3.6.1.4.1.6296.101.28.6.1.1.17Integer32read-onlycurrent
sleHQosInterfaceCosToClass
OBJECT-TYPE
Interface cos to class mapping in no truct mode It represnet COS <VALUE> - CNG <VALUE> - CLASS <VALUE>
1.3.6.1.4.1.6296.101.28.6.1.1.18OCTET STRINGread-onlycurrent
sleHQosInterfaceDscpToClass
OBJECT-TYPE
Interface dscp to class mapping in no truct mode It represnet DSCP <VALUE> - CLASS <VALUE>
1.3.6.1.4.1.6296.101.28.6.1.1.19OCTET STRINGread-onlycurrent
sleHQosInterfaceReplace
OBJECT-TYPE
To rewite the dscp/cos at egress in uniform mode.
1.3.6.1.4.1.6296.101.28.6.1.1.20INTEGER {none(0), cos(1), dscp(2)}read-onlycurrent
sleMlsQosInterfaceTrafficIfgExclude
OBJECT-TYPE
Interface traffic IFG exclude 0 - No 1 - Yes
1.3.6.1.4.1.6296.101.28.6.1.1.21Integer32read-onlycurrent
sleMlsQosInterfaceTrafficPolicingRate
OBJECT-TYPE
Interface traffic policing rate <8-1000000> in kbps
1.3.6.1.4.1.6296.101.28.6.1.1.22Integer32read-onlycurrent
sleMlsQosInterfaceTrafficPolicingBurst
OBJECT-TYPE
Interface traffic policing burst <2-2000>
1.3.6.1.4.1.6296.101.28.6.1.1.23Integer32read-onlycurrent
sleMlsQosInterfaceControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.6.2
sleMlsQosInterfaceControlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.6.2.1INTEGER {setInterfaceQosMapping(1), unSetInterfaceQosMapping(2), setInterfaceTrafficShaping(3), unSetInterfaceTrafficShaping(4), setInterfaceInputPolicyMap(5), unSetInterfaceInputPolicyMap(6), setInterfaceOutputPolicyMap(7), unSetInterfaceOutputPolicyMap(8), setInterfaceOveride(9), unsetInterfaceOveride(10), setInterfaceReplace(11), unsetInterfaceReplace(12), setInterfaceTrafficIfgExclude(13), unsetInterfaceTrafficIfgExclude(14), setInterfaceTrafficPolicingDot3x(15), unsetInterfaceTrafficPolicingDot3x(16)}read-writecurrent
sleMlsQosInterfaceControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.6.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosInterfaceControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.6.2.3Gauge32read-writecurrent
sleMlsQosInterfaceontrolTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.6.2.4TimeTicksread-onlycurrent
sleMlsQosInterfaceControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.6.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosInterfaceCtrlIndex
OBJECT-TYPE
Class map Name
1.3.6.1.4.1.6296.101.28.6.2.6Integer32read-writecurrent
sleMlsQosInterfaceCtrlMapingType
OBJECT-TYPE
Mapping Type: cos (1) Configure interface default CoS values cos-cos (2) Specify cos-cos cos-queue (3) Specify cos-queue map dscp (4) Set the default DSCP vlaue dscp-dscp(5) Specify dscp-dscp dscp-queue (6) DSCP-to-QUEUE exp-exp(7) Specify exp-exp trust (8) Configure port trust state trust-passthrough (9) COnfigure port trust pass-through state cosToClass (10) configure cos to class dscpToClass (11) configure dscp to class
1.3.6.1.4.1.6296.101.28.6.2.7MlsQosInterfaceMapingTyperead-writecurrent
sleMlsQosInterfaceCtrlMapingIngVal
OBJECT-TYPE
Ingress or incoming mapping values. Based on sleMlsQosInterfaceCtrlMapingType, this value has to be set. Ex. If sleMlsQosInterfaceCtrlMapingType = cosToCos, then sleMlsQosInterfaceCtrlMapingIngVal = Incoming or ingress COS value
1.3.6.1.4.1.6296.101.28.6.2.8Integer32read-writecurrent
sleMlsQosInterfaceCtrlMapingEgrVal
OBJECT-TYPE
Egress or outgoing mapping values. Based on sleMlsQosInterfaceCtrlMapingType, this value has to be set. Ex. If sleMlsQosInterfaceCtrlMapingType = cosToCos, then sleMlsQosInterfaceCtrlMapingIngVal = Egress COS value
1.3.6.1.4.1.6296.101.28.6.2.9Integer32read-writecurrent
sleMlsQosInterfaceCtrlMapingCosOverride
OBJECT-TYPE
Interface COS override value
1.3.6.1.4.1.6296.101.28.6.2.10Integer32read-writecurrent
sleMlsQosInterfaceCtrlMapingTrustState
OBJECT-TYPE
Interface trust state Trust: cos (1) dscp (2) Trust pass-through: pass-through cos (1) pass-through dscp (2)
1.3.6.1.4.1.6296.101.28.6.2.11MlsQosIntfTrustStateread-writecurrent
sleMlsQosInterfaceCtrlTrafficShapeRate
OBJECT-TYPE
Interface Traffic shape rate
1.3.6.1.4.1.6296.101.28.6.2.12Integer32read-writecurrent
sleMlsQosInterfaceCtrlTrafficShapeBurst
OBJECT-TYPE
Interface Traffic shape burst
1.3.6.1.4.1.6296.101.28.6.2.13Integer32read-writecurrent
sleMlsQosInterfaceCtrlInputPolicyMap
OBJECT-TYPE
Interface Policy Map mapping
1.3.6.1.4.1.6296.101.28.6.2.14OCTET STRINGread-writecurrent
sleMlsQosInterfaceCtrlOutputPolicyMap
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.6.2.15OCTET STRINGread-writecurrent
sleMlsQosInterfaceCtrlMapingCNGValue
OBJECT-TYPE
Specify CNG value <0-1>
1.3.6.1.4.1.6296.101.28.6.2.16Integer32 (0..1)read-writecurrent
sleMlsQosInterfaceCtrlMapingEgrClassVal
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.6.2.17OCTET STRINGread-writecurrent
sleMlsQosInterfaceCtrlReplace
OBJECT-TYPE
rewite the dscp/cos at egress in uniform mode.
1.3.6.1.4.1.6296.101.28.6.2.18INTEGER {none(0), cos(1), dscp(2)}read-writecurrent
sleMlsQosIntfQue
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.7
sleMlsQosIntfQueTable
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.7.1not-accessiblecurrent
sleMlsQosIntfQueEntry
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.7.1.1not-accessiblecurrent
sleMlsQosIntfQueIntfIndex
OBJECT-TYPE
This Index is based on no of Queues
1.3.6.1.4.1.6296.101.28.7.1.1.1Integer32 (1..65535)not-accessiblecurrent
sleMlsQosIntfQueId
OBJECT-TYPE
This Index is based on no of Queues
1.3.6.1.4.1.6296.101.28.7.1.1.2Integer32 (0..7)not-accessiblecurrent
sleMlsQosIntfQueShapeQueueRate
OBJECT-TYPE
Interface Queue Shape rate
1.3.6.1.4.1.6296.101.28.7.1.1.3Integer32read-onlycurrent
sleMlsQosIntfQueWrrQueueWeight
OBJECT-TYPE
Interface Queue WRR queue weight
1.3.6.1.4.1.6296.101.28.7.1.1.4Integer32read-onlycurrent
sleMlsQosIntfQueWrrRandomDetectMinThr
OBJECT-TYPE
Interface Queue WRR random detect min threshold
1.3.6.1.4.1.6296.101.28.7.1.1.5Integer32read-onlycurrent
sleMlsQosIntfQueWrrRandomDetectMaxThr
OBJECT-TYPE
Interface Queue WRR random detect max threshold
1.3.6.1.4.1.6296.101.28.7.1.1.6Integer32read-onlycurrent
sleMlsQosIntfQueWrrRandomDetectExpWt
OBJECT-TYPE
Interface Queue WRR random detect exp weight
1.3.6.1.4.1.6296.101.28.7.1.1.7Integer32read-onlycurrent
sleMlsQosIntfQueTailDropThr
OBJECT-TYPE
Interface Queue TailDrop threshold
1.3.6.1.4.1.6296.101.28.7.1.1.8Integer32read-onlycurrent
sleMlsQosIntfQueStrictQueue
OBJECT-TYPE
Interface Strict Queue Config
1.3.6.1.4.1.6296.101.28.7.1.1.9Integer32read-onlycurrent
sleMlsQosIntfQueRandomDetectDropStart
OBJECT-TYPE
WRR Random Detect Drop Start
1.3.6.1.4.1.6296.101.28.7.1.1.10Integer32read-onlycurrent
sleMlsQosIntfQueRandomDetectDropSlope
OBJECT-TYPE
WRR Random Detect Drop Slope
1.3.6.1.4.1.6296.101.28.7.1.1.11Integer32read-onlycurrent
sleMlsQosIntfQueRandomDetectColor
OBJECT-TYPE
WRR Random Detect Color
1.3.6.1.4.1.6296.101.28.7.1.1.12INTEGER {yellow(1), red(2)}read-onlycurrent
sleMlsQosIntfQueReservedBandwidth
OBJECT-TYPE
Interface Queue Shape rate (minimum)
1.3.6.1.4.1.6296.101.28.7.1.1.13Integer32 (8..1000000)read-onlycurrent
sleMlsQosIntfQueControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.7.2
sleMlsQosIntfQueControlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.7.2.1INTEGER {setQueueProfile(1), unSetQueueProfile(2)}read-writecurrent
sleMlsQosIntfQueControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.7.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosIntfQueControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.7.2.3Gauge32read-writecurrent
sleMlsQosIntfQueontrolTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.7.2.4TimeTicksread-onlycurrent
sleMlsQosIntfQueControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.7.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosIntfQueCtrlInterfaceIndex
OBJECT-TYPE
Queue Id
1.3.6.1.4.1.6296.101.28.7.2.6Integer32read-writecurrent
sleMlsQosIntfQueCtrlQueueId
OBJECT-TYPE
Queue Id
1.3.6.1.4.1.6296.101.28.7.2.7Integer32read-writecurrent
sleMlsQosIntfQueCtrlProfileType
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.7.2.8MlsQosIntfQueProfilingTyperead-writecurrent
sleMlsQosIntfQueCtrlShapeQueueRate
OBJECT-TYPE
Interface Queue Rate
1.3.6.1.4.1.6296.101.28.7.2.9Integer32read-writecurrent
sleMlsQosIntfQueCtrlWrrQueueWeight
OBJECT-TYPE
Interface Queue WRR Queue weight
1.3.6.1.4.1.6296.101.28.7.2.10Integer32read-writecurrent
sleMlsQosIntfQueCtrlWrrRandomDetectMinThr
OBJECT-TYPE
Interface Queue WRR random detect Min Threshold
1.3.6.1.4.1.6296.101.28.7.2.11Integer32read-writecurrent
sleMlsQosIntfQueCtrlWrrRandomDetectMaxThr
OBJECT-TYPE
Interface Queue WRR random detect Max Threshold
1.3.6.1.4.1.6296.101.28.7.2.12Integer32read-writecurrent
sleMlsQosIntfQueCtrlWrrRandomDetectExpWt
OBJECT-TYPE
Interface Queue WRR random detect exp weight
1.3.6.1.4.1.6296.101.28.7.2.13Integer32read-writecurrent
sleMlsQosIntfQueCtrlTailDropThr
OBJECT-TYPE
Interface Queue Taildrop Threshold
1.3.6.1.4.1.6296.101.28.7.2.14Integer32read-writecurrent
sleMlsQosIntfQueCtrlRandomDetectDropStart
OBJECT-TYPE
Interface Queue WRR Random Detect Drop Start
1.3.6.1.4.1.6296.101.28.7.2.15Integer32read-writecurrent
sleMlsQosIntfQueCtrlRandomDetectDropSlope
OBJECT-TYPE
Interface Queue WRR Random Detect Drop Slope
1.3.6.1.4.1.6296.101.28.7.2.16Integer32read-writecurrent
sleMlsQosIntfQueCtrlRandomDetectColor
OBJECT-TYPE
Interface Queue WRR Random Detect Color
1.3.6.1.4.1.6296.101.28.7.2.17INTEGER {yellow(1), red(2)}read-writecurrent
sleMlsQosIntfQueCtrlReservedBandwidth
OBJECT-TYPE
Interface Queue Rate(minimum)
1.3.6.1.4.1.6296.101.28.7.2.18Integer32 (8..1000000)read-writecurrent
sleMlsQosQStats
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.8
sleMlsQosQStatsTable
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.8.1not-accessiblecurrent
sleMlsQosQStatsEntry
OBJECT-TYPE
1.3.6.1.4.1.6296.101.28.8.1.1not-accessiblecurrent
sleMlsQosQstatsIfIndex
OBJECT-TYPE
Index for the table. QStats Name
1.3.6.1.4.1.6296.101.28.8.1.1.1Integer32 (1..65535)not-accessiblecurrent
sleMlsQosQId
OBJECT-TYPE
This Index is based on Max entries i.e. 64 (dscp)
1.3.6.1.4.1.6296.101.28.8.1.1.2Integer32 (1..8)not-accessiblecurrent
sleMlsQosWredGreenDropPkts
OBJECT-TYPE
Wred Green drop packet counter
1.3.6.1.4.1.6296.101.28.8.1.1.3Counter64read-onlycurrent
sleMlsQosWredYellowDropPkts
OBJECT-TYPE
Wred yellow drop packet counter
1.3.6.1.4.1.6296.101.28.8.1.1.4Counter64read-onlycurrent
sleMlsQosWredRedDropPkts
OBJECT-TYPE
Wred red drop packet counter
1.3.6.1.4.1.6296.101.28.8.1.1.5Counter64read-onlycurrent
sleMlsQosTailDropPkts
OBJECT-TYPE
Taildrop drop packet counter
1.3.6.1.4.1.6296.101.28.8.1.1.6Counter64read-onlycurrent
sleMlsQosTailDropBytes
OBJECT-TYPE
Taildrop drop bytes counter
1.3.6.1.4.1.6296.101.28.8.1.1.7Counter64read-onlycurrent
sleMlsQosQStatsOutPkts
OBJECT-TYPE
Total out packets in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.8Counter64read-onlycurrent
sleMlsQosQStatsOutBytes
OBJECT-TYPE
Total out bytes in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.9Counter64read-onlycurrent
sleMlsQosQStatsMcastOutPkts
OBJECT-TYPE
Total mcast out packets in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.10Counter64read-onlycurrent
sleMlsQosQStatsMcastOutBytes
OBJECT-TYPE
Total mcast out bytes in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.11Counter64read-onlycurrent
sleMlsQosQStatsDropPkts
OBJECT-TYPE
Total drop packets in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.12Counter64read-onlycurrent
sleMlsQosQStatsDropBytes
OBJECT-TYPE
Total drop bytes in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.13Counter64read-onlycurrent
sleMlsQosQStatsMcastDropPkts
OBJECT-TYPE
Total mcast drop packets in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.14Counter64read-onlycurrent
sleMlsQosQStatsMcastDropBytes
OBJECT-TYPE
Total mcast drop bytes in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.15Counter64read-onlycurrent
sleMlsQosQStatsEnqueuedPkts
OBJECT-TYPE
Total Enqueued packets in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.16Counter64read-onlycurrent
sleMlsQosQStatsEnqueuedBytes
OBJECT-TYPE
Total Enqueued bytes in the Queue
1.3.6.1.4.1.6296.101.28.8.1.1.17Counter64read-onlycurrent
sleMlsQosQStatsControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.8.2
sleMlsQosQStatsControlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.8.2.1INTEGER {clearWredStats(1), clearTailDropStats(2), clearQueueStats(3)}read-writecurrent
sleMlsQosQStatsControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.8.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosQStatsControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.8.2.3Gauge32read-writecurrent
sleMlsQosQStatsontrolTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.8.2.4TimeTicksread-onlycurrent
sleMlsQosQStatsControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.8.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosQstatsCtrlIfIndex
OBJECT-TYPE
Index for the table. Class Map name
1.3.6.1.4.1.6296.101.28.8.2.6Integer32read-writecurrent
sleMlsQosQstatsCtrlQId
OBJECT-TYPE
Class map Name
1.3.6.1.4.1.6296.101.28.8.2.7Integer32read-writecurrent
sleHqosClassMapQueue
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.9
sleHqosClassMapQueueInfoTable
OBJECT-TYPE
This Table is used to show the information for Class Map queueing Table
1.3.6.1.4.1.6296.101.28.9.1read-onlycurrent
sleHqosClassMapQueueInfoEntry
OBJECT-TYPE
This Table is used to show the information for Class Map queueing Table
1.3.6.1.4.1.6296.101.28.9.1.1read-onlycurrent
sleHqosClassMapQueueInfoName
OBJECT-TYPE
Class Map queue name. An unique object identify an entry of this table.
1.3.6.1.4.1.6296.101.28.9.1.1.1OCTET STRINGnot-accessiblecurrent
sleHqosClassMapQueueInfoMatchGroup
OBJECT-TYPE
This object is used to show the match group of the class map queueing.
1.3.6.1.4.1.6296.101.28.9.1.1.2INTEGERread-onlycurrent
sleHqosClassMapQueueControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.9.2
sleHqosClassMapQueueControlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.9.2.1INTEGER {createSleHqosClassMapQueueControlEntry(1), deleteSleHqosClassMapQueueControlEntry(2), setSleHqosClassMapQueueControlMatchGroup(3), unsetSleHqosClassMapQueueControlMatchGroup(4)}read-writecurrent
sleHqosClassMapQueueControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.9.2.2SleControlStatusTyperead-onlycurrent
sleHqosClassMapQueueControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.9.2.3Gauge32read-writecurrent
sleHqosClassMapQueueControlTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.9.2.4TimeTicksread-onlycurrent
sleHqosClassMapQueueControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.9.2.5SleControlRequestResultTyperead-onlycurrent
sleHqosClassMapQueueControlName
OBJECT-TYPE
This Object is used to the set the control name for the Class map queue Table
1.3.6.1.4.1.6296.101.28.9.2.6OCTET STRINGread-writecurrent
sleHqosClassMapQueueControlMatchGroup
OBJECT-TYPE
This object is used to set the match group of the class map queueing
1.3.6.1.4.1.6296.101.28.9.2.7INTEGERread-writecurrent
sleHqosPolicyMapQueue
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.10
sleHqosPolicyMapQueueInfoTable
OBJECT-TYPE
This table is used to show the Policy mapping queue information of the policy map queueing
1.3.6.1.4.1.6296.101.28.10.1read-onlycurrent
sleHqosPolicyMapQueueInfoEntry
OBJECT-TYPE
This table is used to show the Policy mapping queue information of the policy map queueing
1.3.6.1.4.1.6296.101.28.10.1.1read-onlycurrent
sleHqosPolicyMapQueueInfoName
OBJECT-TYPE
This object identify an entry in this table.
1.3.6.1.4.1.6296.101.28.10.1.1.1OCTET STRINGnot-accessiblecurrent
sleHqosPolicyMapQueueInfoShape
OBJECT-TYPE
This object is used to show the shape for the policy map queue Types: 1)average 1-1000000000(bps|kbps|mbps|gbps) 2)percent 1-100
1.3.6.1.4.1.6296.101.28.10.1.1.2SnmpAdminString (SIZE(1..48))read-onlycurrent
sleHqosPolicyMapQueueInfoBandwidth
OBJECT-TYPE
This object is used to show the bandwidth for the policy map queue average 1-1000000000(bps|kbps|mbps|gbps) percent 1-100
1.3.6.1.4.1.6296.101.28.10.1.1.3SnmpAdminString (SIZE(1..48))read-onlycurrent
sleHqosPolicyMapQueueInfoBandwidthRemainingPercent
OBJECT-TYPE
This object is used to show the remained bandwidth for the policy map queue
1.3.6.1.4.1.6296.101.28.10.1.1.4INTEGER (1..100)read-onlycurrent
sleHqosPolicyMapQueueInfoQueueLimit
OBJECT-TYPE
This object is used to show the queue limit for the policy map queue
1.3.6.1.4.1.6296.101.28.10.1.1.5SnmpAdminString (SIZE(1..48))read-onlycurrent
sleHqosPolicyMapQueueInfoServicePolicyName
OBJECT-TYPE
This object is used to show the service name for the policy map queue
1.3.6.1.4.1.6296.101.28.10.1.1.6SnmpAdminString (SIZE(1..48))read-onlycurrent
sleHqosPolicyMapQueueInfoPriority
OBJECT-TYPE
This object is used to show the priority for the policy map queue Always value is 1
1.3.6.1.4.1.6296.101.28.10.1.1.7INTEGERread-onlycurrent
sleHqosPolicyMapQueueInfoRDMinThreshold
OBJECT-TYPE
This object is used to show the random detuct minimum threshold for the policy map queue
1.3.6.1.4.1.6296.101.28.10.1.1.8SnmpAdminString (SIZE(1..48))read-onlycurrent
sleHqosPolicyMapQueueInfoRDMaxThreshold
OBJECT-TYPE
This object is used to show the random detuct maximum threshold for the policy map queue
1.3.6.1.4.1.6296.101.28.10.1.1.9SnmpAdminString (SIZE(1..48))read-onlycurrent
sleHqosPolicyMapQueueControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.10.2
sleHqosPolicyMapQueueControlRequest
OBJECT-TYPE
the configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.10.2.1INTEGER {createPolicyMapQueueEntry(1), deletePolicyMapQueueEntry(2), setPolicyMapQueueParameters(3), unsetPolicyMapQueueParameters(4), setPolicyMapQueueServicePolicy(5), unsetPolicyMapQueueServicePolicy(6), setPolicyMapQueueRandomDetect(7), unsetPolicyMapQueueRandomDetect(8)}read-writecurrent
sleHqosPolicyMapQueueControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.10.2.2SleControlStatusTyperead-onlycurrent
sleHqosPolicyMapQueueControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.10.2.3Gauge32read-writecurrent
sleHqosPolicyMapQueueControlTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.10.2.4TimeTicksread-onlycurrent
sleHqosPolicyMapQueueControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.10.2.5SleControlRequestResultTyperead-onlycurrent
sleHqosPolicyMapQueueControlName
OBJECT-TYPE
This object is used to set the name for the policy map queue
1.3.6.1.4.1.6296.101.28.10.2.6OCTET STRINGread-writecurrent
sleHqosPolicyMapQueueControlClassMapQueueName
OBJECT-TYPE
This object is used to set the name for the policy map queue
1.3.6.1.4.1.6296.101.28.10.2.7OCTET STRINGread-writecurrent
sleHqosPolicyMapQueueControlParams
OBJECT-TYPE
This object is used to set 1)shape: the shape for the policy map queue is to configure shaping on an egress queue to impose a maximum rate on it 2)queue-limit: the Queue Limit is to configure tail drop by setting queue limits on both ingress and egress queues 3)bandwidth: To allocate a minimum percentage of the interface bandwidth to a queue 4)bandwidth-Remain: To configures the bandwidth remaining on the interface in a queue 5)Priority: To configure a single output queuing class as the priority queue average 1-1000000000(bps|kbps|mbps|gbps) limit 1-131072 (packets | bytes | kbytes) percent 1-100
1.3.6.1.4.1.6296.101.28.10.2.8INTEGER {shape(1), queueLimit(2), bandwidth(3), bandwidthRemain(4), priority(5)}read-writecurrent
sleHqosPolicyMapQueueControlParamsValue
OBJECT-TYPE
This object is used to set 1)shape: the shape for the policy map queue is to configure shaping on an egress queue to impose a maximum rate on it 2)queue-limit: the Queue Limit is to configure tail drop by setting queue limits on both ingress and egress queues 3)bandwidth: To allocate a minimum percentage of the interface bandwidth to a queue 4)bandwidth-Remain: To configures the bandwidth remaining on the interface in a queue 5)Priority: To configure a single output queuing class as the priority queue average 1-1000000000(bps|kbps|mbps|gbps) limit 1-131072 (packets | bytes | kbytes) percent 1-100
1.3.6.1.4.1.6296.101.28.10.2.9INTEGERread-writecurrent
sleHqosPolicyMapQueueControlUnits
OBJECT-TYPE
This object is used to set the units for the specified objects
1.3.6.1.4.1.6296.101.28.10.2.10INTEGER {bps(1), kbps(2), mbps(3), gbps(4), packets(5), bytes(6), kbytes(7), average(8), percent(9)}read-writecurrent
sleHqosPolicyMapQueueControlRDMiniThreshold
OBJECT-TYPE
his object is used to set the Minimum random threashold
1.3.6.1.4.1.6296.101.28.10.2.11INTEGER (1..131072)read-writecurrent
sleHqosPolicyMapQueueControlRDMaxThreshold
OBJECT-TYPE
This object is used to set the Maximum random threashold
1.3.6.1.4.1.6296.101.28.10.2.12INTEGER (1..131072)read-writecurrent
sleHqosPolicyMapQueueControlRDMinimumUnits
OBJECT-TYPE
This object is used to set the units for Random Minimum
1.3.6.1.4.1.6296.101.28.10.2.13INTEGER {bytes(1), kbytes(2), packets(3), percent(4)}read-writecurrent
sleHqosPolicyMapQueueControlRDMaximumUnits
OBJECT-TYPE
This object is used to set the units for Random Maximum
1.3.6.1.4.1.6296.101.28.10.2.14INTEGER {bytes(1), kbytes(2), packets(3), percent(4)}read-writecurrent
sleHqosPolicyMapQueueControlServicePolicyName
OBJECT-TYPE
This object is used to set the service name, to attach a child policy onto a parent policy
1.3.6.1.4.1.6296.101.28.10.2.15SnmpAdminString (SIZE(1..48))read-writecurrent
sleMlsQosAclGlobal
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.11
sleMlsQosAclGlobalInfo
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.11.1
sleMlsQosAclGlobalInfoMaxAccessList
OBJECT-TYPE
Max accessList suported
1.3.6.1.4.1.6296.101.28.11.1.1Unsigned32read-onlycurrent
sleMlsQosAclGlobalControl
OBJECT-IDENTITY
1.3.6.1.4.1.6296.101.28.11.2
sleMlsQosAclGlobalControlRequest
OBJECT-TYPE
The configuration commands, and user can configure functions via setting this entry as proper value.
1.3.6.1.4.1.6296.101.28.11.2.1INTEGER {setMaxAccessList(1), unsetMaxAccessList(2)}read-writecurrent
sleMlsQosAclGlobalControlStatus
OBJECT-TYPE
status of user command. User have to check this value as .busy. or .idle. before do setRequest.
1.3.6.1.4.1.6296.101.28.11.2.2SleControlStatusTyperead-onlycurrent
sleMlsQosAclGlobalControlTimer
OBJECT-TYPE
the wait-time until setRequest end. In case of short-time command, this value is 0
1.3.6.1.4.1.6296.101.28.11.2.3Gauge32read-writecurrent
sleMlsQosAclGlobalControlTimeStamp
OBJECT-TYPE
the time stamp of the last command. (don.t care)
1.3.6.1.4.1.6296.101.28.11.2.4TimeTicksread-onlycurrent
sleMlsQosAclGlobalControlReqResult
OBJECT-TYPE
Result of the last command.
1.3.6.1.4.1.6296.101.28.11.2.5SleControlRequestResultTyperead-onlycurrent
sleMlsQosAclGlobalControlMaxAccessList
OBJECT-TYPE
Max accessList suported
1.3.6.1.4.1.6296.101.28.11.2.6Unsigned32read-writecurrent

Conformance

NameOIDStatus
sleMlsQosGroup
OBJECT-GROUP
Description.
1.3.6.1.4.1.6296.101.28.12current