SAFEGUARD-ENGINE-MIB
- Registered at
- 1.3.6.1.4.1.171.12.19
- Last updated
- 2006-01-16 00:00
- Organization
- Namespace
- dlink
- Source file
SAFEGUARD-ENGINE-MIB- Digest
sha256:bf5663804b5be1726ba168b06292ce090002e3326897584c98529a42094b640a
Description
The MIB module for managing CPU protection.
Imports
| From | Symbols |
|---|---|
| DLINK-ID-REC-MIB | dlink-common-mgmt |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
DLINK-ID-REC-MIB SAFEGUARD-ENGINE-MIB SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| swSafeGuardGblMgmt OBJECT-IDENTITY | 1.3.6.1.4.1.171.12.19.1 | |||
| swSafeGuardAdminState OBJECT-TYPE This object indicates the Safe Guard state of the switch. | 1.3.6.1.4.1.171.12.19.1.1 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swSafeGuardctrl OBJECT-IDENTITY | 1.3.6.1.4.1.171.12.19.2 | |||
| swSafeGuardRisingThreshold OBJECT-TYPE The object indicates CPU protection rising threshold in percentage. the range is between 20%-100% , if the CPU utilization is over the rising threshold, the switch enters exhausted mode. | 1.3.6.1.4.1.171.12.19.2.1 | INTEGER (20..100) | read-write | current |
| swSafeGuardFallingThreshold OBJECT-TYPE The object indicates CPU protection falling threshold in percentage. the range is between 20%-100% , if the CPU utilization is lower than the falling threshold, the switch enters normal mode. | 1.3.6.1.4.1.171.12.19.2.2 | INTEGER (20..100) | read-write | current |
| swSafeGuardmode OBJECT-TYPE determine the controlling method of broadcast traffic. Here are two modes (strict and fuzzy). In strict, the Switch will stop receiving all 'ARP not to me' packets (the protocol address of target in ARP packet is the Switch itself). That means no matter what reasons cause the high CPU utilization (may not caused by ARP storm), the Switch reluctantly processes any 'ARP not to me' packets in exhausted mode. In fuzzy mode, the Switch will adjust the bandwidth dynamically depend on some reasonable algorithm. | 1.3.6.1.4.1.171.12.19.2.3 | INTEGER {strict(1), fuzzy(2)} | read-write | current |
| swSafeGuardAlarmAdminState OBJECT-TYPE This object indicates the state of cpu protection related trap/log mechanism (enable or disable). If set to enable, trap and log will be active while cpu protection current mode changed.If set to disable, current mode change will not trigger trap and log events. | 1.3.6.1.4.1.171.12.19.2.4 | INTEGER {other(1), disabled(2), enabled(3)} | read-write | current |
| swSafeGuardCurrentStatus OBJECT-TYPE This object indicates current operation mode of Safe Guard | 1.3.6.1.4.1.171.12.19.2.5 | INTEGER {normal(1), exhausted(2)} | read-only | current |
| swSafeGuardInterval OBJECT-TYPE The object indicates CPU utilization monitor interval in seconds. The range is between 5 to 10, default value is 5. | 1.3.6.1.4.1.171.12.19.2.6 | INTEGER (0..65535) | read-only | current |
| swSafeGuardNotify OBJECT-IDENTITY | 1.3.6.1.4.1.171.12.19.4 | |||
| swSafeGuardNotification OBJECT-IDENTITY | 1.3.6.1.4.1.171.12.19.4.1 | |||
| swSafeGuardNotifyPrefix OBJECT-IDENTITY | 1.3.6.1.4.1.171.12.19.4.1.0 |
Notifications
| Name | OID | Status |
|---|---|---|
| swSafeGuardChgToExhausted NOTIFICATION-TYPE This trap indicates System change operation mode from normal to exhausted. | 1.3.6.1.4.1.171.12.19.4.1.0.1 | current |
| swSafeGuardChgToNormal NOTIFICATION-TYPE This trap indicates System change operation mode from exhausted to normal. | 1.3.6.1.4.1.171.12.19.4.1.0.2 | current |