MIBs Depot

RS-XX9-DVBT2-MIB

Registered at
1.3.6.1.4.1.2566.127.1.2.216.5.0
1.3.6.1.4.1.2566.127.1.2.216.5.1
1.3.6.1.4.1.2566.127.1.2.216.5.2
1.3.6.1.4.1.2566.149.1.216.5
Last updated
2015-08-25 11:00
Organization
Rohde&Schwarz GmbH & Co. KG
Revisions
2015-08-25 11:00, 2014-12-22 16:00, 2014-12-03 11:00, 2014-11-03 16:00, 2014-05-15 15:00, 2014-01-14 17:00, 2011-09-12 12:00
Namespace
rs
Source file
RS-XX9-DVBT2-MIB
Digest
sha256:efc864b952878d1aef12f68537deb670c884544ff6d089932d72f2ef48400111

Description

This MIB defines DVB-T2 specific objects of XX9000 transmitting systems from Rohde & Schwarz. The following MIBs are related to this: - RS-COMMON-MIB - mandatory for this MIB. - RS-XX9-SMI-MIB - mandatory for this MIB. - RS-XX9-TC-MIB - mandatory for this MIB. - RS-XX9-COMMON-MIB - mandatory for this MIB.

Contact

Rohde & Schwarz GmbH & Co. KG Broadcasting Division Muehldorfstrasse 15 81671 Munich Germany customersupport@rohde-schwarz.com

Imports

FromSymbols
RS-XX9-COMMON-MIBcommonNotificationAlarmClass
RS-XX9-SMI-MIBrsXx9DvbT2, rsXx9MibModule
RS-XX9-TC-MIBIndexAB, IndexTransmitter, NotificationMask, NotificationPriority, NotificationState, SwitchOnOff
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIInteger32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ENTITY-MIB
IANA-ENTITY-MIB
INET-ADDRESS-MIB
RS-COMMON-MIB
RS-XX9-COMMON-MIB
RS-XX9-DVBT2-MIB
RS-XX9-SMI-MIB
RS-XX9-TC-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
UUID-TC-MIB

Textual conventions

NameOIDSyntaxAccessStatus
Dvbt2BasebandMode
TEXTUAL-CONVENTION
highEfficiency(4) - certain normally unused bytes in the data stream are used for data transmission. This mode may not be supported by some devices.
current
Dvbt2CellIdSource
TEXTUAL-CONVENTION
The Cell ID enables the receiver to identify a DVB-T2 cell. manual(1) - from dvbt2LocalizationCellIdManual l1(2) - from the L1 frame information of the DVB-T2 gateway stream ia(3) - from the individual addressing data of the DVB-T2 gateway stream
current
Dvbt2ChannelBandwidth
TEXTUAL-CONVENTION
mhz1p7(3) - 1.7 MHz mhz5(4) - 5 MHz mhz6(5) - 6 MHz mhz7(6) - 7 MHz mhz8(7) - 8 MHz
current
Dvbt2CodeRate
TEXTUAL-CONVENTION
PLP code rate.
current
Dvbt2FEC
TEXTUAL-CONVENTION
PLP FEC type.
current
Dvbt2FftSize
TEXTUAL-CONVENTION
FFT size.
current
Dvbt2GuardInterval
TEXTUAL-CONVENTION
Guard interval of the super-frame. oneDiv32(2) -> 1/32 oneDiv16(3) -> 1/16 oneDiv8(4) -> 1/8 oneDiv4(5) -> 1/4 oneDiv128(6) -> 1/128 nineteenDiv128(7) -> 19/128 nineteenDiv256(8) -> 19/256
current
Dvbt2IndividualAddressingSource
TEXTUAL-CONVENTION
dataNotAnnounced(1) - individual addressing information not available viaBroadcast(2) - all transmitters of the network got the same information via broadcast txSpecific(3) - a special information was given for this TX identifier
current
Dvbt2L1FrequencySource
TEXTUAL-CONVENTION
Source of L1 frequency shift. If a T2-MI interface is used, you usually select l1(2), but for testing manual(1) may be selected. If TS feed is used, only manual(1) is possible.
current
Dvbt2Layer1CodeRate
TEXTUAL-CONVENTION
Coding of the layer 1 post signalling data block.
current
Dvbt2Layer1FEC
TEXTUAL-CONVENTION
Layer 1 FEC used for the layer 1 post signalling data block.
current
Dvbt2Layer1Modulation
TEXTUAL-CONVENTION
Constellation of the layer 1 post signalling data block.
current
Dvbt2Modulation
TEXTUAL-CONVENTION
PLP modulation.
current
Dvbt2OnOff
TEXTUAL-CONVENTION
On / Off information for certain DVB-T2 values.
current
Dvbt2PaprReduction
TEXTUAL-CONVENTION
PAPR (Peak to Average Power Ratio) reduction used, if any. ace(4) - Active Constellation Extension tr(5) - Tone Reservation aceTr(6) - ACE and TR combined
current
Dvbt2PilotPattern
TEXTUAL-CONVENTION
The scattered pilot pattern used for the data OFDM symbols.
current
Dvbt2PlpType
TEXTUAL-CONVENTION
PLP type.
current
Dvbt2T2Version
TEXTUAL-CONVENTION
v111(3) - version 1.1.1 v121(4) - version 1.2.1 v131(5) - version 1.3.1
current
Dvbt2TimeInterleaverType
TEXTUAL-CONVENTION
Type of time-interleaving.
current
Dvbt2TransmissionSystem
TEXTUAL-CONVENTION
t2Miso(2) is an approach to improve the link throughput using two antennas on transmitter site while using a single receiver antenna.
current
Dvbt2TxDelayOffsetSource
TEXTUAL-CONVENTION
Source for transmitter specific transmitting delay. If a T2-MI interface is used, you may choose: ia(2) - take from IA parameters off(1) - deactivated If TS feed is used, no choice is possible.
current

Objects

NameOIDSyntaxAccessStatus
rsXx9Dvbt2Notifications
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.0
rsXx9Dvbt2Objects
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.1
dvbt2Status
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.1.1
dvbt2StatusNotificationTable
OBJECT-TYPE
The context information/configuration for the DVB-T2 status notifications.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1not-accessiblecurrent
dvbt2StatusNotificationEntry
OBJECT-TYPE
An entry in the dvbt2StatusNotificationTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1.1not-accessiblecurrent
dvbt2StatusNotificationTxIdx
OBJECT-TYPE
The transmitter index.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1.1.1IndexTransmitternot-accessiblecurrent
dvbt2StatusNotificationExcIdx
OBJECT-TYPE
This index distinguishes the exiters. Necessary if you have dual drive transmitters.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1.1.2IndexABnot-accessiblecurrent
dvbt2StatusNotificationIdx
OBJECT-TYPE
The notification number as below rsXx9Dvbt2Notifications. This is a helper column and therefore not-accessible.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1.1.3Unsigned32 (1..12)not-accessiblecurrent
dvbt2StatusNotificationName
OBJECT-TYPE
The notification number as an enumeration. The enumeration correlates with the notifications under rsXx9Dvbt2Notifications.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1.1.4INTEGER {dvbt2L1State(1), dvbt2IaState(2), dvbt2ConfigurationValid(5), dvbt2ConfigurationSupported(6), dvbt2ConfigurationMatched(7), dvbt2EncoderSummary(8), dvbt2Test(9), dvbt2SupportedPlps(10), dvbt2SupportedTrIterations(11), dvbt2T2MiTimeInterleaverBuffer(12), dvbt2CompositeSummary(100), dvbt2CompositeProfiles(101), dvbt2CompositeFrameLength(102), dvbt2SubIaState(202), dvbt2SubConfigurationValid(205), dvbt2SubConfigurationSupported(206), dvbt2SubConfigurationMatched(207)}read-writecurrent
dvbt2StatusNotificationMask
OBJECT-TYPE
See TextualConvention for details.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1.1.5NotificationMaskread-writecurrent
dvbt2StatusNotificationPriority
OBJECT-TYPE
See TextualConvention for details.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1.1.6NotificationPriorityread-writecurrent
dvbt2StatusNotificationState
OBJECT-TYPE
See TextualConvention for details.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.1.1.7NotificationStateread-onlycurrent
dvbt2StateTable
OBJECT-TYPE
DVB-T2 state information.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2not-accessiblecurrent
dvbt2StateEntry
OBJECT-TYPE
An entry for a specific exciter.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2.1not-accessiblecurrent
dvbt2StInputDetected
OBJECT-TYPE
The current input state. internal(3) represents the test generator. unlocked(2), mpeg(4), t2mi(5): the status of the active input.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2.1.1INTEGER {off(1), unlocked(2), internal(3), mpeg(4), t2mi(5)}read-onlycurrent
dvbt2StInputMatched
OBJECT-TYPE
Result of comparison of dvbt2StInputDetected and dvbt2StInputRequired.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2.1.2INTEGER {off(2), no(4), yes(5)}read-onlycurrent
dvbt2StInputRequired
OBJECT-TYPE
The current required input state. off(1) is startup value, only. internal(3) is the test generator. mpeg(4), t2mi(5): the requirement towards an active input.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2.1.3INTEGER {off(1), internal(3), mpeg(4), t2mi(5)}read-onlycurrent
dvbt2StConfigAdaptionState
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2.1.4INTEGER {undefined(1), notUsed(2), wrongConfig(4), ok(5)}read-onlycurrent
dvbt2StDejitterBufDelay
OBJECT-TYPE
This displays the delay of the T2MI stream within the dejitter buffer. The value varies after the transmission has started due to conditions on the input network. This value should be positive. A negative value may impose transmission interrupts.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2.1.5Integer32 (-1000000..1000000)read-onlycurrent
dvbt2StResidualDelay
OBJECT-TYPE
Delay of the signal controlled by the SFN Synchronization to meet the desired transmission time. The value is fix after transmission has started. To achieve a higher robustness against input jitter, this value can be reduced by increasing the dejitter buffer delay.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2.1.6Unsigned32 (0..500000)read-onlycurrent
dvbt2StConfigurationMsg
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.1.2.1.7SnmpAdminString (SIZE(0..160))read-onlycurrent
dvbt2Setup
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.1.2
dvbt2ConfigurationTable
OBJECT-TYPE
DVB-T2 configuration.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1not-accessiblecurrent
dvbt2ConfigurationEntry
OBJECT-TYPE
An entry in the dvbt2ConfigurationTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1.1not-accessiblecurrent
dvbt2ConfigurationTxIdx
OBJECT-TYPE
The transmitter index.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1.1.1IndexTransmitternot-accessiblecurrent
dvbt2ConfigurationExcIdx
OBJECT-TYPE
This index distinguishes the exiters. Necessary if you have dual drive transmitters.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1.1.2IndexABnot-accessiblecurrent
dvbt2ConfigurationT2MiInterface
OBJECT-TYPE
on(1) - Uses the incoming T2-MI stream from a DVB-T2 gateway to configure the Modulator. off(2) - Uses the incoming MPEG transport stream directly as payload for single PLP.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1.1.3INTEGER {on(1), off(2), composite(3)}read-writecurrent
dvbt2ConfigurationT2MiPID
OBJECT-TYPE
Only if dvbt2ConfigurationT2MiInterface is on(1): the packet ID of the T2-MI elementary stream.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1.1.4Unsigned32 (0..8191)read-writecurrent
dvbt2ConfigurationT2MiSID
OBJECT-TYPE
Only if dvbt2FsT2Version is at least v131(5):
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1.1.5Unsigned32 (0..7)read-writecurrent
dvbt2ConfigurationT2ConfigAdaption
OBJECT-TYPE
Defines adaptation of the processing to the configuration at the input. None: This setting can always be used; it does, however, lead to a high processing delay through the transmitter. Static single PLP: This setting can only be used if the data stream only contains one PLP (Physical Layer Pipe). It decreases the processing delay through the exciter. staticMultiPLP(3) is not supported anymore.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1.1.6INTEGER {none(1), staticSinglePLP(2), staticMultiPLP(3)}read-writecurrent
dvbt2ConfigurationT2MiDejitterBufDelay
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.1.1.7Unsigned32 (0..1000)read-writecurrent
dvbt2LocalizationTable
OBJECT-TYPE
DVB-T2 localization.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2not-accessiblecurrent
dvbt2LocalizationEntry
OBJECT-TYPE
An entry in the dvbt2LocalizationTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1not-accessiblecurrent
dvbt2LocalizationTxIdentifier
OBJECT-TYPE
Used to address a TV transmitter within a DVB-T2 network.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.3Unsigned32 (0..65535)read-writecurrent
dvbt2LocalizationCellIdSource
OBJECT-TYPE
Source for the cell ID.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.4Dvbt2CellIdSourceread-writecurrent
dvbt2LocalizationCellIdManual
OBJECT-TYPE
The cell ID used when dvbt2LocalizationCellIdSource is manual(1). The cell ID can be changed without signal interruption.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.5Unsigned32 (0..65535)read-writecurrent
dvbt2LocalizationMisoGroupSource
OBJECT-TYPE
The MISO group can be configured either manually directly on the transmitter or automatically using the Individual Addressing (IA) data via the DVB_T2 gateway. The group can be switched at any time without signal interruption. manual(2) - from dvbt2LocalizationMisoGroupManual ia(3) - from the individual addressing data of the DVB-T2 gateway stream
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.6INTEGER {off(1), manual(2), ia(3)}read-writecurrent
dvbt2LocalizationMisoGroupManual
OBJECT-TYPE
The MISO group used when dvbt2LocalizationMisoGroupSource is manual(1). The MISO group can be changed without signal interruption.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.7INTEGER {group1(4), group2(5)}read-writecurrent
dvbt2LocalizationNetworkIdManual
OBJECT-TYPE
The network ID uniquely defines the current DVB-T2 network. If a T2-MI interface is used, this value is specified from the DVB-T2 gateway. Otherwise it is defined here.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.8Unsigned32 (0..65535)read-writecurrent
dvbt2LocalizationSystemIdManual
OBJECT-TYPE
The system ID uniquely identifies a T2 system within the DVB-T2 network.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.9Unsigned32 (0..65535)read-writecurrent
dvbt2LocalizationL1FrequencySource
OBJECT-TYPE
See textual convention. If you select manual(1), the value is given with dvbt2LocalizationL1FrequencyManual.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.10Dvbt2L1FrequencySourceread-writecurrent
dvbt2LocalizationL1FrequencyManual
OBJECT-TYPE
Presetting of L1 frequency shift.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.11Unsigned32 (0..2000000000)read-writecurrent
dvbt2LocalizationTxDelayOffsetSource
OBJECT-TYPE
See textual convention.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.12Dvbt2TxDelayOffsetSourceread-writecurrent
dvbt2LocalizationPaprTrSource
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.2.1.13INTEGER {off(1), manual(2), ia(3), supported(4)}read-writecurrent
dvbt2IndividualAddressingTable
OBJECT-TYPE
DVB-T2 individual addressing.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.3not-accessiblecurrent
dvbt2IndividualAddressingEntry
OBJECT-TYPE
An entry in the dvbt2IndividualAddressingTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.3.1not-accessiblecurrent
dvbt2IaTimeOffset
OBJECT-TYPE
Shows the transmitting delay for this transmitter in relation to other transmitters in the DVB-T2 network. This value is defined from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.3.1.3Integer32 (-32768..32767)read-onlycurrent
dvbt2IaTimeOffsetSource
OBJECT-TYPE
Shows the source for the time offset. txSpecific(2) - a special time offset was given for this TX identifier viaBroadcast(3) - all transmitters of the network got the same time offset via broadcast
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.3.1.4Dvbt2IndividualAddressingSourceread-onlycurrent
dvbt2IaFrequencyOffset
OBJECT-TYPE
Shows the frequency shift for this transmitter in relation to other transmitters in the DVB-T2 network. This value is defined from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.3.1.5Integer32read-onlycurrent
dvbt2IaFrequencyOffsetSource
OBJECT-TYPE
Shows the source for the frequency shift. txSpecific(2) - a special frequency shift was given for this TX identifier viaBroadcast(3) - all transmitters of the network got the same frequency shift via broadcast
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.3.1.6Dvbt2IndividualAddressingSourceread-writecurrent
dvbt2IaCellID
OBJECT-TYPE
Shows the cell ID that is given with the individual addressing information. This value is defined from the DVB-T2 gateway. The actual cell ID depends on the setting of dvbt2LocalizationCellIdSource.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.3.1.7Unsigned32 (0..65535)read-onlycurrent
dvbt2IaCellIdSource
OBJECT-TYPE
Shows the source for the cell ID. txSpecific(2) - a special cell ID was given for this TX identifier viaBroadcast(3) - all transmitters of the network got the same cell ID via broadcast
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.3.1.8Dvbt2IndividualAddressingSourceread-onlycurrent
dvbt2ChannelTable
OBJECT-TYPE
DVB-T2 channel parameters.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4not-accessiblecurrent
dvbt2ChannelEntry
OBJECT-TYPE
An entry in the dvbt2ChannelTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4.1not-accessiblecurrent
dvbt2ChnTransmissionSystem
OBJECT-TYPE
Allows to connect several transmitters to a MISO system. Only applicable if a T2-MI interface is used. A change of this value is possible anytime without signal interruption.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4.1.3INTEGER {t2SISO(3), t2MISO(4)}read-writecurrent
dvbt2ChnBandwidth
OBJECT-TYPE
The channel bandwidth that the DVB-T2 signal allocates in the frequency spectrum. For safety reasons it is always set manually.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4.1.4Dvbt2ChannelBandwidthread-writecurrent
dvbt2ChnFFT
OBJECT-TYPE
If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4.1.5Dvbt2FftSizeread-writecurrent
dvbt2ChnFftExtended
OBJECT-TYPE
If this field is set to on(1), the extended carrier mode is used. If this field is set to off(2), the normal carrier mode is used. Only for 8K, 16K or 32K FFT size. If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4.1.6SwitchOnOffread-writecurrent
dvbt2ChnGuardInterval
OBJECT-TYPE
see textual convention If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4.1.7Dvbt2GuardIntervalread-writecurrent
dvbt2ChnPilotPattern
OBJECT-TYPE
see textual convention If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4.1.8Dvbt2PilotPatternread-writecurrent
dvbt2ChnPaprReduction
OBJECT-TYPE
see textual convention If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.4.1.9Dvbt2PaprReductionread-writecurrent
dvbt2FrameStructureTable
OBJECT-TYPE
DVB-T2 frame structure.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.5not-accessiblecurrent
dvbt2FrameStructureEntry
OBJECT-TYPE
An entry in the dvbt2FrameStructureTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.5.1not-accessiblecurrent
dvbt2FsDataSymbolsPerT2Frame
OBJECT-TYPE
The total number of symbols in a frame (excluding P1). If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.5.1.3Unsigned32 (1..4095)read-writecurrent
dvbt2FsT2FramesPerSuperFrame
OBJECT-TYPE
The number of T2-frames in a super-frame is a configurable parameter. If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.5.1.4Unsigned32 (1..255)read-writecurrent
dvbt2FsT2Version
OBJECT-TYPE
The T2 version used. If no T2-MI interface is used, only version 1.1.1 is supported.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.5.1.5Dvbt2T2Versionread-writecurrent
dvbt2L1Table
OBJECT-TYPE
DVB-T2 layer 1 parameters.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.6not-accessiblecurrent
dvbt2L1Entry
OBJECT-TYPE
An entry in the dvbt2L1Table.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.6.1not-accessiblecurrent
dvbt2L1Modulation
OBJECT-TYPE
The constellation of the L1-post signalling data block. If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.6.1.3Dvbt2Layer1Modulationread-writecurrent
dvbt2L1CodeRate
OBJECT-TYPE
The coding of the L1-post signalling data block. If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.6.1.4Dvbt2Layer1CodeRateread-writecurrent
dvbt2L1FEC
OBJECT-TYPE
The type of the L1 FEC used for the L1-post signalling data block. If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.6.1.5Dvbt2Layer1FECread-writecurrent
dvbt2L1Repetition
OBJECT-TYPE
Repetition of L1-post dynamic data. If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.6.1.6SwitchOnOffread-writecurrent
dvbt2Plp1Table
OBJECT-TYPE
Changeable parameters of the only physical layer pipe in case of single PLP mode.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7not-accessiblecurrent
dvbt2Plp1Entry
OBJECT-TYPE
An entry in the dvbt2PlpTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1not-accessiblecurrent
dvbt2Plp1ID
OBJECT-TYPE
uniquely identifies a PLP within a T2 system
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.3Unsigned32 (0..255)read-writecurrent
dvbt2Plp1GroupID
OBJECT-TYPE
identifies with which PLP group within the T2 system the current PLP is associated. This can be used by a receiver to link the data PLP to its associated common PLP, which will have the same PLP Group ID.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.4Unsigned32 (0..255)read-writecurrent
dvbt2Plp1Type
OBJECT-TYPE
Indicates the set Physical Layer Pipe type.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.5Dvbt2PlpTyperead-writecurrent
dvbt2Plp1Constellation
OBJECT-TYPE
Indicates the set modulation mode. QPSK is extremely fail-safe, but has only a low data rate. 256QAM can transmit very high data rates and is recommended if few faults are expected on the transmission link. The setting can be changed here.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.6Dvbt2Modulationread-writecurrent
dvbt2Plp1Rotation
OBJECT-TYPE
Constellation rotation.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.7SwitchOnOffread-writecurrent
dvbt2Plp1CodeRate
OBJECT-TYPE
Indicates the set code rate. The code rate is used to set the ratio of information data to <error correction values + information data>. 1/2 provides the greatest error correction and the lowest data transfer rate; 5/6 provides the lowest error correction and the greatest data transfer rate. The setting can be changed here.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.8Dvbt2CodeRateread-writecurrent
dvbt2Plp1FEC
OBJECT-TYPE
Indicates the set error correction algorithm (FEC). If a T2-MI interface is used, this value is fixed by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.9Dvbt2FECread-writecurrent
dvbt2Plp1TimeInterleaverType
OBJECT-TYPE
single(1) - Maps each interleaving frame directly to a T2 frame. multi(2) - Maps each interleaving frame to more than one T2 frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.10Dvbt2TimeInterleaverTyperead-writecurrent
dvbt2Plp1TimeInterleaverLength
OBJECT-TYPE
Defines the number of time interleaver blocks (TIB) within the time interleaving frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.11Unsigned32 (0..255)read-writecurrent
dvbt2Plp1BasebandMode
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.7.1.12Dvbt2BasebandModeread-writecurrent
dvbt2TestTable
OBJECT-TYPE
Configures the test mode of the exciter.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.9not-accessiblecurrent
dvbt2TestEntry
OBJECT-TYPE
An entry in the dvbt2TestTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.9.1not-accessiblecurrent
dvbt2TestGeneration
OBJECT-TYPE
Switches test signal generation on or off. A test signal enables measurements for the transmitter if no valid DVB-T2 input exists or the DVB-T2 option is not active.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.9.1.3SwitchOnOffread-writeobsolete
dvbt2TestMode
OBJECT-TYPE
Indicates which test signal is generated. off: Switches off test signal generation. PRBS:Generates a PRBS sequence instead of the payload. Mute 1st P1 Symbol: Suppresses the first symbol of each T2 frame. This function can be used to measure the time of signal transmission. Single Carrier: Generates an unmodulated single carrier. The frequency of the single carrier is at the center of the band and therefore deviates from the vision carrier frequency. This test signal can be used to measure the phase noise of the synthesizer. The phase noise must be measured via the RF Monitor Out connector (X61). The cable connected to RF Out (X60) must be removed. In order to protect the amplifiers, this test signal is only generated if the output of the exciter is open.
1.3.6.1.4.1.2566.127.1.2.216.5.1.2.9.1.4INTEGER {off(1), prbs(2), singleCarrier(3), mute1P1SymOfSuperFrame(6)}read-writecurrent
dvbt2Output
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.1.3
dvbt2OutLocalizationTable
OBJECT-TYPE
DVB-T2 localization as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2not-accessiblecurrent
dvbt2OutLocalizationEntry
OBJECT-TYPE
An entry in the dvbt2OutLocalizationTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1not-accessiblecurrent
dvbt2OutLocalizationCellIdSource
OBJECT-TYPE
See textual convention.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.1Dvbt2CellIdSourceread-onlycurrent
dvbt2OutLocalizationCellId
OBJECT-TYPE
The cell ID that is actually transmitted.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.3Unsigned32read-onlycurrent
dvbt2OutLocalizationMisoGroupSource
OBJECT-TYPE
Source for the MISO group: manual(2) - from dvbt2LocalizationMisoGroupManual ia(3) - from the individual addressing data of the DVB-T2 gateway stream
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.4INTEGER {off(1), manual(2), ia(3)}read-onlycurrent
dvbt2OutLocalizationMisoGroup
OBJECT-TYPE
The actual MISO group for the transmitter. In a MISO system the two transmitters have to be assigned different groups. In a SFN system several transmitters may belong to one group.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.5INTEGER {unused(3), group1(4), group2(5)}read-onlycurrent
dvbt2OutLocalizationNetworkId
OBJECT-TYPE
The actual network ID for the transmitter.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.6Unsigned32read-onlycurrent
dvbt2OutLocalizationSystemId
OBJECT-TYPE
The actual system ID for the transmitter.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.7Unsigned32read-onlycurrent
dvbt2OutLocalizationL1FrequencySource
OBJECT-TYPE
See textual convention.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.8Dvbt2L1FrequencySourceread-onlycurrent
dvbt2OutLocalizationL1Frequency
OBJECT-TYPE
Currently used L1 frequency with index 0.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.9Unsigned32read-onlycurrent
dvbt2OutLocalizationTxDelayOffsetSource
OBJECT-TYPE
See textual convention.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.10Dvbt2TxDelayOffsetSourceread-onlycurrent
dvbt2OutLocalizationTxDelayOffset
OBJECT-TYPE
Transmitter specific transmitting delay.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.11Integer32read-onlycurrent
dvbt2OutLocalizationPaprTrSource
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.2.1.12INTEGER {off(1), manual(2), ia(3), supported(4)}read-writecurrent
dvbt2OutChannelTable
OBJECT-TYPE
DVB-T2 channel parameters as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4not-accessiblecurrent
dvbt2OutChannelEntry
OBJECT-TYPE
An entry in the dvbt2OutChannelTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1not-accessiblecurrent
dvbt2OutChnTransmissionSystem
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.3Dvbt2TransmissionSystemread-onlycurrent
dvbt2OutChnBandwidth
OBJECT-TYPE
The channel bandwidth as signalled by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.4Dvbt2ChannelBandwidthread-onlycurrent
dvbt2OutChnFFT
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.5Dvbt2FftSizeread-onlycurrent
dvbt2OutChnFftExtended
OBJECT-TYPE
When this field is on(1), the extended carrier mode is used. If this field is off(2), the normal carrier mode is used. Only for 8K, 16K or 32K FFT size.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.6Dvbt2OnOffread-onlycurrent
dvbt2OutChnGuardInterval
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.7Dvbt2GuardIntervalread-onlycurrent
dvbt2OutChnPilotPattern
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.8Dvbt2PilotPatternread-onlycurrent
dvbt2OutChnPaprReduction
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.9Dvbt2PaprReductionread-onlycurrent
dvbt2OutChnT2BaseLite
OBJECT-TYPE
Shows whether the sent out T2-Base profile is compatible with a T2-LITE profile.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.10Dvbt2OnOffread-onlycurrent
dvbt2OutChnPreamble
OBJECT-TYPE
Indicates whether the preambles are all of the same type or not: notMixed(3) - all preambles in the current transmission are of the same type mixed(4) - preambles of different types are transmitted
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.11INTEGER {undefined(1), notMixed(3), mixed(4)}read-writecurrent
dvbt2OutChnInputStreamTypes
OBJECT-TYPE
The types of the Tx input streams carried within the T2 super-frame: tsOnly(3) - transport stream (TS) only gsOnly(4) - generic stream, but not TS tsAndGs(5) - both TS and generic stream
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.12INTEGER {undefined(1), tsOnly(3), gsOnly(4), tsAndGs(5)}read-onlycurrent
dvbt2OutChnRegenerationFlag
OBJECT-TYPE
Indicates how many times the DVB-T2 signal has been re-generated. Value 0 indicates that no regeneration has been done. Each time the DVB-T2 signal is regenerated this field is increased by one.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.13Unsigned32read-onlycurrent
dvbt2OutChnT2Profile
OBJECT-TYPE
The T2-profile used. The standard profile is T2-Base, while T2-Lite has been introduced in T2 version 1.3.1. T2-Lite is intended for mobile applications. The T2-Base-Lite option is the intersection between T2-Base and T2-Lite, i.e. a signal that is valid for both T2-Base and T2-Lite profiles. The T2-Base-Lite profile will be signalled as a normal T2-Base signal, but with the T2_BASE_LITE flag set in the L1-Pre signaling.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.4.1.14INTEGER {undefined(1), base(3), baseLite(4), lite(5)}read-onlycurrent
dvbt2OutFrameStructureTable
OBJECT-TYPE
DVB-T2 frame structure as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.5not-accessiblecurrent
dvbt2OutFrameStructureEntry
OBJECT-TYPE
An entry in the dvbt2OutFrameStructureTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.5.1not-accessiblecurrent
dvbt2OutFsDataSymbolsPerT2Frame
OBJECT-TYPE
The total number of symbols in a frame (excluding P1). If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.5.1.3Unsigned32read-onlycurrent
dvbt2OutFsT2FramesPerSuperFrame
OBJECT-TYPE
The number of T2-frames in a super-frame is a configurable parameter. If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.5.1.4Unsigned32read-onlycurrent
dvbt2OutFsT2Version
OBJECT-TYPE
If no T2-MI interface is used only version 1.1.1 is supported.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.5.1.5Dvbt2T2Versionread-onlycurrent
dvbt2OutFsSubSlicesPerFrame
OBJECT-TYPE
The total number of sub-slices for the type 2 data PLPs across all RF channels in one T2-frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.5.1.6Unsigned32read-onlycurrent
dvbt2OutFsNumOfPLP
OBJECT-TYPE
The number of PLPs carried within the super-frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.5.1.7Unsigned32read-onlycurrent
dvbt2OutFsNumOfAux
OBJECT-TYPE
number of auxiliary streams
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.5.1.8Unsigned32read-onlycurrent
dvbt2OutL1Table
OBJECT-TYPE
DVB-T2 layer 1 parameters as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.6not-accessiblecurrent
dvbt2OutL1Entry
OBJECT-TYPE
An entry in the dvbt2OutL1Table.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.6.1not-accessiblecurrent
dvbt2OutL1Modulation
OBJECT-TYPE
The constellation of the L1-post signalling data block.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.6.1.3Dvbt2Layer1Modulationread-onlycurrent
dvbt2OutL1CodeRate
OBJECT-TYPE
The coding of the L1-post signalling data block.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.6.1.4Dvbt2Layer1CodeRateread-onlycurrent
dvbt2OutL1FEC
OBJECT-TYPE
The type of the L1 FEC used for the L1-post signalling data block.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.6.1.5Dvbt2Layer1FECread-onlycurrent
dvbt2OutL1Repetition
OBJECT-TYPE
Repetition of L1-post dynamic data.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.6.1.6Dvbt2OnOffread-onlycurrent
dvbt2OutL1PostScrambled
OBJECT-TYPE
Shows whether signalling of L1-post is scrambled.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.6.1.7Dvbt2OnOffread-onlycurrent
dvbt2OutL1PostExtension
OBJECT-TYPE
Indicates the presence of the L1-post extension field.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.6.1.8Dvbt2OnOffread-onlycurrent
dvbt2OutPlpTable
OBJECT-TYPE
DVB-T2 PLP parameters as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7not-accessiblecurrent
dvbt2OutPlpEntry
OBJECT-TYPE
An entry in the dvbt2OutPlpTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1not-accessiblecurrent
dvbt2OutPlpIdx
OBJECT-TYPE
The PLP number. This is a helper column and therefore not-accessible.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.2Unsigned32 (1..8)not-accessiblecurrent
dvbt2OutPlpID
OBJECT-TYPE
uniquely identifies a PLP within a T2 system
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.3Unsigned32read-onlycurrent
dvbt2OutPlpGroupID
OBJECT-TYPE
identifies with which PLP group within the T2 system the current PLP is associated. This can be used by a receiver to link the data PLP to its associated common PLP, which will have the same PLP Group ID.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.4Unsigned32read-onlycurrent
dvbt2OutPlpType
OBJECT-TYPE
Indicates the set Physical Layer Pipe type.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.5Dvbt2PlpTyperead-onlycurrent
dvbt2OutPlpPayloadType
OBJECT-TYPE
Each input PLP may take one of the following formats: gfps(3) - Generic Fixed-length Packetized Stream This form is retained for compatibility with DVB-S2, but it is expected that GSE would now be used instead. gcs(4) - Generic Continuous Stream A variable length packet stream where the modulator is not aware of the packet boundaries. gse(5) - Generic Encapsulated Stream ts(6) - Transport Stream
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.6INTEGER {reserved(2), gfps(3), gcs(4), gse(5), ts(6)}read-onlycurrent
dvbt2OutPlpConstellation
OBJECT-TYPE
Indicates the set modulation mode. QPSK is extremely fail-safe, but has only a low data rate. 256QAM can transmit very high data rates and is recommended if few faults are expected on the transmission link.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.7Dvbt2Modulationread-onlycurrent
dvbt2OutPlpRotation
OBJECT-TYPE
Constellation rotation.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.8Dvbt2OnOffread-onlycurrent
dvbt2OutPlpCodeRate
OBJECT-TYPE
Indicates the set code rate. The code rate is used to set the ratio of information data to <error correction values + information data>. 1/2 provides the greatest error correction and the lowest data transfer rate; 5/6 provides the lowest error correction and the greatest data transfer rate.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.9Dvbt2CodeRateread-onlycurrent
dvbt2OutPlpFEC
OBJECT-TYPE
Indicates the set error correction algorithm (FEC). If a T2-MI interface is used, this value is fixed by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.10Dvbt2FECread-onlycurrent
dvbt2OutPlpFecBlocks
OBJECT-TYPE
Displays the received number of maximum FEC blocks per interleaving frame. obsoleted
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.11Unsigned32read-onlyobsolete
dvbt2OutPlpTimeInterleaverType
OBJECT-TYPE
single(1) - Maps each interleaving frame directly to a T2 frame. multi(2) - Maps each interleaving frame to more than one T2 frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.12Dvbt2TimeInterleaverTyperead-onlycurrent
dvbt2OutPlpTimeInterleaverLength
OBJECT-TYPE
Defines the number of time interleaver blocks (TIB) within the time interleaving frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.13Unsigned32read-onlycurrent
dvbt2OutPlpBasebandMode
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.14Dvbt2BasebandModeread-onlycurrent
dvbt2OutPlpFrameInterval
OBJECT-TYPE
Indicates the T2-frame interval within the super-frame for the associated PLP.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.15Unsigned32read-onlycurrent
dvbt2OutPlpBasebandPayloadPadding
OBJECT-TYPE
Shows whether frame padding is used in base band for achieving constant length of base band frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.16Dvbt2OnOffread-onlycurrent
dvbt2OutPlpNullPacketDeletion
OBJECT-TYPE
Shows whether null packets (PID=8191) including the optional ISSY field are deleted.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.17Dvbt2OnOffread-onlycurrent
dvbt2OutPlpNumOfOtherPlpInBand
OBJECT-TYPE
If equal 0, the relevant PLP carries only its own in-band L1 dynamic information. If greater 0, it carries L1 dynamic information of other PLPs as well as its own information, for shorter channel switching time.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.18Unsigned32read-onlycurrent
dvbt2OutPlpCmType
OBJECT-TYPE
Coding and modulation type: Code rate, constellation and rotation aCM(3) - may be different for different PLPs cCM(4) - are equal for all PLPs
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.19INTEGER {undefined(1), aCM(3), cCM(4)}read-onlycurrent
dvbt2OutPlpISSY
OBJECT-TYPE
Input stream synchronization: shows whether ISSY information is included off(3) - no ISSY information short(4) - 16 bit ISSY information long(5) - 24 bit ISSY information obsoleted
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.20INTEGER {undefined(1), off(3), short(4), long(5)}read-onlyobsolete
dvbt2OutPlpInBandFlag
OBJECT-TYPE
Indicates whether the padding carries in-band signalling information. (Available with T2-Version 1.1.1)
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.21Dvbt2OnOffread-onlycurrent
dvbt2OutPlpInBandASig
OBJECT-TYPE
Indicates whether the padding carries in-band signalling information of type A. (Available with T2-Version 1.2.1 or higher)
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.22Dvbt2OnOffread-onlycurrent
dvbt2OutPlpInBandBSig
OBJECT-TYPE
Indicates whether the padding carries in-band signalling information of type B. (Available with T2-Version 1.2.1 or higher)
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.7.1.23Dvbt2OnOffread-onlycurrent
dvbt2OutPaprTrTable
OBJECT-TYPE
PAPR (Peak to Average Power Ratio) reduction using tone reservation parameters.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.8not-accessiblecurrent
dvbt2OutPaprTrEntry
OBJECT-TYPE
An entry in the dvbt2OutPaprTrTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.8.1not-accessiblecurrent
dvbt2OutPaprTrIterations
OBJECT-TYPE
Indicates the maximum number of tone reservation repetitions that are supported by the currently selected Bandwidth, FFT and Guard Interval settings.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.8.1.1Unsigned32read-onlycurrent
dvbt2OutPaprTrClippingThreshold
OBJECT-TYPE
Indicates the limit up to which the PAPR-TR algorithm operates. The displayed value divided by 100 roughly corresponds to the desired crest factor in dB.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.8.1.2Unsigned32read-onlycurrent
dvbt2OutPaprTrIterationsSupported
OBJECT-TYPE
Maximum number of iterations of tone reservation that are supported for the adjusted bandwidth, FFT and guard interval.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.8.1.3Unsigned32read-onlycurrent
dvbt2OutPaprTrIterationsIA
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.8.1.4Unsigned32read-onlycurrent
dvbt2OutPaprTrIterationsReduced
OBJECT-TYPE
The number of iterations signalled by IA is too high. The number of active iterations is reduced to the number of supported iterations.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.8.1.5TruthValueread-onlycurrent
dvbt2OutPaprTrIterationsActive
OBJECT-TYPE
Number of iterations of tone reservations per symbol.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.8.1.6Unsigned32read-onlycurrent
dvbt2OutFefTable
OBJECT-TYPE
FEF (future extension frame) values.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.9not-accessiblecurrent
dvbt2OutFefEntry
OBJECT-TYPE
An entry in the dvbt2OutFefTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.9.1not-accessiblecurrent
dvbt2OutFefOn
OBJECT-TYPE
Indicates whether future extension frames are used.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.9.1.1Dvbt2OnOffread-onlycurrent
dvbt2OutFefType
OBJECT-TYPE
Indicates the type of the associated FEF part as a digit.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.9.1.2Unsigned32read-onlycurrent
dvbt2OutFefLength
OBJECT-TYPE
Indicates the length of the used FEF part as the number of periods T from the beginning of the P1 symbol of the FEF part to the beginning of the P1 symbol of the next T2 frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.9.1.3Unsigned32read-onlycurrent
dvbt2OutFefInterval
OBJECT-TYPE
Indicates the number of T2-frames between two FEF parts.
1.3.6.1.4.1.2566.127.1.2.216.5.1.3.9.1.4Unsigned32read-onlycurrent
dvbt2CoderSub
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.1.10
dvbt2SubStatus
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.1
dvbt2SubStateTable
OBJECT-TYPE
DVB-T2 Coder-Sub state information.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.1.2not-accessiblecurrent
dvbt2SubStateEntry
OBJECT-TYPE
An entry in the dvbt2SubStateTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.1.2.1not-accessiblecurrent
dvbt2SubStInputDetected
OBJECT-TYPE
The current input state. internal(3) represents the test generator. unlocked(2), mpeg(4), t2mi(5): the status of the active input.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.1.2.1.1INTEGER {off(1), unlocked(2), internal(3), mpeg(4), t2mi(5)}read-onlycurrent
dvbt2SubStInputMatched
OBJECT-TYPE
Result of comparison of dvbt2StInputDetected and dvbt2StInputRequired.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.1.2.1.2INTEGER {off(2), no(4), yes(5)}read-onlycurrent
dvbt2SubStConfigurationMsg
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.1.2.1.7SnmpAdminString (SIZE(0..160))read-onlycurrent
dvbt2SubSetup
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2
dvbt2SubConfigurationTable
OBJECT-TYPE
DVB-T2 Coder-Sub configuration.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.1not-accessiblecurrent
dvbt2SubConfigurationEntry
OBJECT-TYPE
An entry in the dvbt2SubConfigurationTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.1.1not-accessiblecurrent
dvbt2SubConfigurationT2MiInterface
OBJECT-TYPE
on(1) - Uses the incoming T2-MI stream from a DVB-T2 gateway to configure the Modulator. off(2) - Uses the incoming MPEG transport stream directly as payload for single PLP.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.1.1.3INTEGER {on(1), off(2), composite(3)}read-onlycurrent
dvbt2SubConfigurationT2MiPID
OBJECT-TYPE
Only if dvbt2ConfigurationT2MiInterface is on(1): the packet ID of the T2-MI elementary stream.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.1.1.4Unsigned32 (0..8191)read-writecurrent
dvbt2SubConfigurationT2MiSID
OBJECT-TYPE
Only if dvbt2FsT2Version is at least v131(5):
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.1.1.5Unsigned32 (0..7)read-writecurrent
dvbt2SubLocalizationTable
OBJECT-TYPE
DVB-T2 Coder-Sub localization.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2not-accessiblecurrent
dvbt2SubLocalizationEntry
OBJECT-TYPE
An entry in the dvbt2SubLocalizationTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2.1not-accessiblecurrent
dvbt2SubLocalizationTxIdentifier
OBJECT-TYPE
Used to address a TV transmitter within a DVB-T2 network.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2.1.3Unsigned32 (0..65535)read-writecurrent
dvbt2SubLocalizationCellIdSource
OBJECT-TYPE
Source for the cell ID.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2.1.4Dvbt2CellIdSourceread-writecurrent
dvbt2SubLocalizationCellIdManual
OBJECT-TYPE
The cell ID used when dvbt2LocalizationCellIdSource is manual(1). The cell ID can be changed without signal interruption.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2.1.5Unsigned32 (0..65535)read-writecurrent
dvbt2SubLocalizationMisoGroupSource
OBJECT-TYPE
The MISO group can be configured either manually directly on the transmitter or automatically using the Individual Addressing (IA) data via the DVB_T2 gateway. The group can be switched at any time without signal interruption. manual(2) - from dvbt2LocalizationMisoGroupManual ia(3) - from the individual addressing data of the DVB-T2 gateway stream
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2.1.6INTEGER {off(1), manual(2), ia(3)}read-writecurrent
dvbt2SubLocalizationMisoGroupManual
OBJECT-TYPE
The MISO group used when dvbt2LocalizationMisoGroupSource is manual(1). The MISO group can be changed without signal interruption.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2.1.7INTEGER {group1(4), group2(5)}read-writecurrent
dvbt2SubLocalizationL1FrequencySource
OBJECT-TYPE
See textual convention. If you select manual(1), the value is given with dvbt2LocalizationL1FrequencyManual.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2.1.10Dvbt2L1FrequencySourceread-writecurrent
dvbt2SubLocalizationL1FrequencyManual
OBJECT-TYPE
Presetting of L1 frequency shift.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.2.2.1.11Unsigned32 (0..2000000000)read-writecurrent
dvbt2SubOutput
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3
dvbt2SubOutLocalizationTable
OBJECT-TYPE
DVB-T2 Coder-Sub localization as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2not-accessiblecurrent
dvbt2SubOutLocalizationEntry
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1not-accessiblecurrent
dvbt2SubOutLocalizationCellIdSource
OBJECT-TYPE
See textual convention.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1.1Dvbt2CellIdSourceread-onlycurrent
dvbt2SubOutLocalizationCellId
OBJECT-TYPE
The cell ID that is actually transmitted.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1.3Unsigned32read-onlycurrent
dvbt2SubOutLocalizationMisoGroupSource
OBJECT-TYPE
Source for the MISO group: manual(2) - from dvbt2LocalizationMisoGroupManual ia(3) - from the individual addressing data of the DVB-T2 gateway stream
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1.4INTEGER {off(1), manual(2), ia(3)}read-onlycurrent
dvbt2SubOutLocalizationMisoGroup
OBJECT-TYPE
The actual MISO group for the transmitter. In a MISO system the two transmitters have to be assigned different groups. In a SFN system several transmitters may belong to one group.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1.5INTEGER {unused(3), group1(4), group2(5)}read-onlycurrent
dvbt2SubOutLocalizationNetworkId
OBJECT-TYPE
The actual network ID for the transmitter.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1.6Unsigned32read-onlycurrent
dvbt2SubOutLocalizationSystemId
OBJECT-TYPE
The actual system ID for the transmitter.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1.7Unsigned32read-onlycurrent
dvbt2SubOutLocalizationL1Frequency
OBJECT-TYPE
Currently used L1 frequency with index 0.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1.9Unsigned32read-onlycurrent
dvbt2SubOutLocalizationPaprTrSource
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.2.1.12INTEGER {off(1), manual(2), ia(3), supported(4)}read-writecurrent
dvbt2SubOutChannelTable
OBJECT-TYPE
DVB-T2 Coder-Sub channel parameters as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4not-accessiblecurrent
dvbt2SubOutChannelEntry
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1not-accessiblecurrent
dvbt2SubOutChnTransmissionSystem
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1.3Dvbt2TransmissionSystemread-onlycurrent
dvbt2SubOutChnBandwidth
OBJECT-TYPE
The channel bandwidth as signalled by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1.4Dvbt2ChannelBandwidthread-onlycurrent
dvbt2SubOutChnFFT
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1.5Dvbt2FftSizeread-onlycurrent
dvbt2SubOutChnFftExtended
OBJECT-TYPE
When this field is on(1), the extended carrier mode is used. If this field is off(2), the normal carrier mode is used. Only for 8K, 16K or 32K FFT size.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1.6Dvbt2OnOffread-onlycurrent
dvbt2SubOutChnGuardInterval
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1.7Dvbt2GuardIntervalread-onlycurrent
dvbt2SubOutChnPilotPattern
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1.8Dvbt2PilotPatternread-onlycurrent
dvbt2SubOutChnPaprReduction
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1.9Dvbt2PaprReductionread-onlycurrent
dvbt2SubOutChnT2Profile
OBJECT-TYPE
The T2-profile used. The standard profile is T2-Base, while T2-Lite has been introduced in T2 version 1.3.1. T2-Lite is intended for mobile applications. The T2-Base-Lite option is the intersection between T2-Base and T2-Lite, i.e. a signal that is valid for both T2-Base and T2-Lite profiles. The T2-Base-Lite profile will be signalled as a normal T2-Base signal, but with the T2_BASE_LITE flag set in the L1-Pre signaling.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.4.1.14INTEGER {undefined(1), base(3), baseLite(4), lite(5)}read-onlycurrent
dvbt2SubOutFrameStructureTable
OBJECT-TYPE
DVB-T2 Coder-Sub frame structure as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.5not-accessiblecurrent
dvbt2SubOutFrameStructureEntry
OBJECT-TYPE
An entry in the dvbt2SubOutFrameStructureTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.5.1not-accessiblecurrent
dvbt2SubOutFsDataSymbolsPerT2Frame
OBJECT-TYPE
The total number of symbols in a frame (excluding P1). If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.5.1.3Unsigned32read-onlycurrent
dvbt2SubOutFsT2FramesPerSuperFrame
OBJECT-TYPE
The number of T2-frames in a super-frame is a configurable parameter. If a T2-MI interface is used, this value is read-only. In this case it is specified by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.5.1.4Unsigned32read-onlycurrent
dvbt2SubOutFsT2Version
OBJECT-TYPE
If no T2-MI interface is used only version 1.1.1 is supported.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.5.1.5Dvbt2T2Versionread-onlycurrent
dvbt2SubOutFsNumOfPLP
OBJECT-TYPE
The number of PLPs carried within the super-frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.5.1.7Unsigned32read-onlycurrent
dvbt2SubOutFsNumOfAux
OBJECT-TYPE
number of auxiliary streams
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.5.1.8Unsigned32read-onlycurrent
dvbt2SubOutL1Table
OBJECT-TYPE
DVB-T2 Coder-Sub layer 1 parameters as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.6not-accessiblecurrent
dvbt2SubOutL1Entry
OBJECT-TYPE
An entry in the dvbt2SubOutL1Table.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.6.1not-accessiblecurrent
dvbt2SubOutL1Modulation
OBJECT-TYPE
The constellation of the L1-post signalling data block.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.6.1.3Dvbt2Layer1Modulationread-onlycurrent
dvbt2SubOutL1CodeRate
OBJECT-TYPE
The coding of the L1-post signalling data block.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.6.1.4Dvbt2Layer1CodeRateread-onlycurrent
dvbt2SubOutL1Repetition
OBJECT-TYPE
Repetition of L1-post dynamic data.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.6.1.6Dvbt2OnOffread-onlycurrent
dvbt2SubOutL1PostScrambled
OBJECT-TYPE
Shows whether signalling of L1-post is scrambled.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.6.1.7Dvbt2OnOffread-onlycurrent
dvbt2SubOutPlpTable
OBJECT-TYPE
DVB-T2 Coder-Sub PLP parameters as signalled from the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7not-accessiblecurrent
dvbt2SubOutPlpEntry
OBJECT-TYPE
An entry in the dvbt2SubOutPlpTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1not-accessiblecurrent
dvbt2SubOutPlpIdx
OBJECT-TYPE
The PLP number. This is a helper column and therefore not-accessible.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.2Unsigned32 (1..8)not-accessiblecurrent
dvbt2SubOutPlpID
OBJECT-TYPE
uniquely identifies a PLP within a T2 system
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.3Unsigned32read-onlycurrent
dvbt2SubOutPlpGroupID
OBJECT-TYPE
identifies with which PLP group within the T2 system the current PLP is associated. This can be used by a receiver to link the data PLP to its associated common PLP, which will have the same PLP Group ID.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.4Unsigned32read-onlycurrent
dvbt2SubOutPlpType
OBJECT-TYPE
Indicates the set Physical Layer Pipe type.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.5Dvbt2PlpTyperead-onlycurrent
dvbt2SubOutPlpPayloadType
OBJECT-TYPE
Each input PLP may take one of the following formats: gfps(3) - Generic Fixed-length Packetized Stream This form is retained for compatibility with DVB-S2, but it is expected that GSE would now be used instead. gcs(4) - Generic Continuous Stream A variable length packet stream where the modulator is not aware of the packet boundaries. gse(5) - Generic Encapsulated Stream ts(6) - Transport Stream
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.6INTEGER {reserved(2), gfps(3), gcs(4), gse(5), ts(6)}read-onlycurrent
dvbt2SubOutPlpConstellation
OBJECT-TYPE
Indicates the set modulation mode. QPSK is extremely fail-safe, but has only a low data rate. 256QAM can transmit very high data rates and is recommended if few faults are expected on the transmission link.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.7Dvbt2Modulationread-onlycurrent
dvbt2SubOutPlpRotation
OBJECT-TYPE
Constellation rotation.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.8Dvbt2OnOffread-onlycurrent
dvbt2SubOutPlpCodeRate
OBJECT-TYPE
Indicates the set code rate. The code rate is used to set the ratio of information data to <error correction values + information data>. 1/2 provides the greatest error correction and the lowest data transfer rate; 5/6 provides the lowest error correction and the greatest data transfer rate.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.9Dvbt2CodeRateread-onlycurrent
dvbt2SubOutPlpFEC
OBJECT-TYPE
Indicates the set error correction algorithm (FEC). If a T2-MI interface is used, this value is fixed by the DVB-T2 gateway.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.10Dvbt2FECread-onlycurrent
dvbt2SubOutPlpTimeInterleaverType
OBJECT-TYPE
single(1) - Maps each interleaving frame directly to a T2 frame. multi(2) - Maps each interleaving frame to more than one T2 frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.12Dvbt2TimeInterleaverTyperead-onlycurrent
dvbt2SubOutPlpTimeInterleaverLength
OBJECT-TYPE
Defines the number of time interleaver blocks (TIB) within the time interleaving frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.13Unsigned32read-onlycurrent
dvbt2SubOutPlpBasebandMode
OBJECT-TYPE
see textual convention
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.7.1.14Dvbt2BasebandModeread-onlycurrent
dvbt2SubOutPaprTrTable
OBJECT-TYPE
Coder-Sub PAPR (Peak to Average Power Ratio) reduction using tone reservation parameters.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.8not-accessiblecurrent
dvbt2SubOutPaprTrEntry
OBJECT-TYPE
An entry in the dvbt2SubOutPaprTrTable.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.8.1not-accessiblecurrent
dvbt2SubOutPaprTrIterations
OBJECT-TYPE
Indicates the maximum number of tone reservation repetitions that are supported by the currently selected Bandwidth, FFT and Guard Interval settings.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.8.1.1Unsigned32read-onlycurrent
dvbt2SubOutPaprTrClippingThreshold
OBJECT-TYPE
Indicates the limit up to which the PAPR-TR algorithm operates. The displayed value divided by 100 roughly corresponds to the desired crest factor in dB.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.8.1.2Unsigned32read-onlycurrent
dvbt2SubOutPaprTrIterationsSupported
OBJECT-TYPE
Maximum number of iterations of tone reservation that are supported for the adjusted bandwidth, FFT and guard interval.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.8.1.3Unsigned32read-onlycurrent
dvbt2SubOutPaprTrIterationsIA
OBJECT-TYPE
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.8.1.4Unsigned32read-onlycurrent
dvbt2SubOutPaprTrIterationsReduced
OBJECT-TYPE
The number of iterations signalled by IA is too high. The number of active iterations is reduced to the number of supported iterations.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.8.1.5TruthValueread-onlycurrent
dvbt2SubOutPaprTrIterationsActive
OBJECT-TYPE
Number of iterations of tone reservations per symbol.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.8.1.6Unsigned32read-onlycurrent
dvbt2SubOutFefTable
OBJECT-TYPE
Coder-Sub FEF (future extension frame) values.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.9not-accessiblecurrent
dvbt2SubOutFefEntry
OBJECT-TYPE
An entry in the dvbt2SubOutFefTable
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.9.1not-accessiblecurrent
dvbt2SubOutFefOn
OBJECT-TYPE
Indicates whether future extension frames are used.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.9.1.1Dvbt2OnOffread-onlycurrent
dvbt2SubOutFefType
OBJECT-TYPE
Indicates the type of the associated FEF part as a digit.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.9.1.2Unsigned32read-onlycurrent
dvbt2SubOutFefLength
OBJECT-TYPE
Indicates the length of the used FEF part as the number of periods T from the beginning of the P1 symbol of the FEF part to the beginning of the P1 symbol of the next T2 frame.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.9.1.3Unsigned32read-onlycurrent
dvbt2SubOutFefInterval
OBJECT-TYPE
Indicates the number of T2-frames between two FEF parts.
1.3.6.1.4.1.2566.127.1.2.216.5.1.10.3.9.1.4Unsigned32read-onlycurrent
rsXx9Dvbt2Conformance
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.2
rsXx9Dvbt2Compliances
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.2.1
rsXx9Dvbt2Groups
OBJECT-IDENTITY
1.3.6.1.4.1.2566.127.1.2.216.5.2.2

Notifications

NameOIDStatus
dvbt2L1State
NOTIFICATION-TYPE
When using a T2 MI interface this status shows, how the values from the L1 frame information are used: Possible values: undefined(1) off(2) - L1 frame information values not used fault(3) - L1 framing is not supported by this software version, please update the TCE software ok(5) - L1 frame information values are correct and are used for modulation Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.1current
dvbt2IaState
NOTIFICATION-TYPE
Shows usage of the 'individual addressing' parameters of the data stream. Possible values: undefined(1) off(2) - not used warning(4) - in use, but not available ok(5) - in use and available Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.2current
dvbt2ConfigurationValid
NOTIFICATION-TYPE
Shows whether the configuration of DVB-T2 parameters is coherent. Possible values: off(2) - unchecked warning(4) - invalid configuration ok(5) - valid configuration Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.5current
dvbt2ConfigurationSupported
NOTIFICATION-TYPE
Indicates whether the selected modualtion mode is supported by this exciter. Possible values: off(2) - unchecked warning(4) - unsupported configuration ok(5) - supported configuration Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.6current
dvbt2ConfigurationMatched
NOTIFICATION-TYPE
Indicates whether the configuration of the channel bandwidth is consistent. If not, an error message is output. Possible values: off(2) - warning(4) - invalid configuration ok(5) - valid configuration Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.7current
dvbt2EncoderSummary
NOTIFICATION-TYPE
Encoder summary state. Possible values: off(2) warning(4) ok(5) Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.8current
dvbt2Test
NOTIFICATION-TYPE
Possible values: off(2) - no test signal generation warning(4) - test signal generation is activated Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.9current
dvbt2SupportedPlps
NOTIFICATION-TYPE
Possible values: off(2) warning(4) ok(5) Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.10current
dvbt2SupportedTrIterations
NOTIFICATION-TYPE
Possible values: off(2) warning(4) ok(5) Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.11current
dvbt2T2MiTimeInterleaverBuffer
NOTIFICATION-TYPE
obsolete Possible values: undefined(1) off(2) - not used warning(4) - underflow ok(5) - ok
1.3.6.1.4.1.2566.127.1.2.216.5.0.12obsolete
dvbt2CompositeSummary
NOTIFICATION-TYPE
Description. Possible values: off(2) - warning(4) - ok(5) -
1.3.6.1.4.1.2566.127.1.2.216.5.0.100current
dvbt2CompositeProfiles
NOTIFICATION-TYPE
Description. Possible values: off(2) - warning(4) - ok(5) -
1.3.6.1.4.1.2566.127.1.2.216.5.0.101current
dvbt2CompositeFrameLength
NOTIFICATION-TYPE
Description. Possible values: off(2) - warning(4) - ok(5) -
1.3.6.1.4.1.2566.127.1.2.216.5.0.102current
dvbt2SubIaState
NOTIFICATION-TYPE
Shows usage of the 'individual addressing' parameters of the data stream. Possible values: undefined(1) off(2) - not used warning(4) - in use, but not available ok(5) - in use and available Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.202current
dvbt2SubConfigurationValid
NOTIFICATION-TYPE
Shows whether the configuration of DVB-T2 parameters is coherent. Possible values: off(2) - unchecked warning(4) - invalid configuration ok(5) - valid configuration Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.205current
dvbt2SubConfigurationSupported
NOTIFICATION-TYPE
Indicates whether the selected modualtion mode is supported by this exciter. Possible values: off(2) - unchecked warning(4) - unsupported configuration ok(5) - supported configuration Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.206current
dvbt2SubConfigurationMatched
NOTIFICATION-TYPE
Indicates whether the configuration of the channel bandwidth is consistent. If not, an error message is output. Possible values: off(2) - warning(4) - invalid configuration ok(5) - valid configuration Notification class: warning
1.3.6.1.4.1.2566.127.1.2.216.5.0.207current

Conformance

NameOIDStatus
dvbt2BasicCompliance
MODULE-COMPLIANCE
The compliance statement for XX9000 DVB-T2 exciters.
1.3.6.1.4.1.2566.127.1.2.216.5.2.1.1current
dvbt2ObjBasic
OBJECT-GROUP
Basic objects group.
1.3.6.1.4.1.2566.127.1.2.216.5.2.2.1current
dvbt2NotifyBasic
NOTIFICATION-GROUP
Basic notifications group.
1.3.6.1.4.1.2566.127.1.2.216.5.2.2.2current
dvbt2ObjObsoleted
OBJECT-GROUP
Obsoleted objects group.
1.3.6.1.4.1.2566.127.1.2.216.5.2.2.3obsolete
dvbt2ObjSubBasic
OBJECT-GROUP
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.2.2.4current
dvbt2NotifySubBasic
NOTIFICATION-GROUP
Description.
1.3.6.1.4.1.2566.127.1.2.216.5.2.2.5current
dvbt2NotifObsoleted
NOTIFICATION-GROUP
Obsoleted notifications group.
1.3.6.1.4.1.2566.127.1.2.216.5.2.2.6obsolete