MIBs Depot

ROSMGMT-OPTICAL-TRANSCEIVER-MIB

Registered at
1.3.6.1.4.1.8886.60.18
Last updated
2020-04-16 00:00
Organization
Raisecom, Inc.
Revisions
2020-04-16 00:00
Namespace
raisecom
Source file
ROSMGMT-OPTICAL-TRANSCEIVER-MIB
Digest
sha256:72950630127f9233bfeca392aa571d3b35d71c14ac20e22a56443b6184a3ebcf

Description

This MIB module defines objects to monitor optical characteristics on the optical interfaces in a network element.

Contact

Raise Systems Postal: Beijing, China Tel: 86-010-82884499 E-mail: chenyu@raisecom.com

Imports

FromSymbols
IF-MIBifIndex
RAISECOM-BASE-MIBrosMgmt
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIInteger32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

IANAifType-MIB
IF-MIB
RAISECOM-BASE-MIB
ROSMGMT-OPTICAL-TRANSCEIVER-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
EnableVar
TEXTUAL-CONVENTION
enable or disable a function.
current
OpticalPMPeriod
TEXTUAL-CONVENTION
This value indicates the time period over which performance monitoring data has been collected.
current
OpticalParameterType
TEXTUAL-CONVENTION
This value indicates the optical parameter that is being monitored. Valid values are -OpticalParameterType transceiverTemperature(1) :transceiver temperature txbiasCurrent(2) :TX bias current txPower(3) :TX output power rxPower(4) :RX received optical power laserTemperature(5) :laser temperature p5V0supplyVoltage(6) :+5V supply voltage p3V3supplyVoltage(7) :+3.3V supply voltage p1V8supplyVoltage(8) :+1.8V supply voltage n5V2supplyVoltage(9) :-5.2V supply voltage apdBiasVoltage(10) :APD bias voltage p5V0supplyCurrent(11) :+5V supply currnet p3V3supplyCurrent(12) :+3.3V supply currnet p1V8supplyCurrent(13) :+1.8V supply currnet n5V2supplyCurrent(14) :-5.2V supply currnet tecCurrent(15) :TEC currnet laserWavelength(16) :laser wavelength
current
OpticalParameterValue
TEXTUAL-CONVENTION
The value of the optical parameter that is being monitored. The range of values varies depending on the type of optical parameter being monitored, as identified by a corresponding object with syntax OpticalParameterType. When the optical parameter being monitored is 'XXTemperature',the supported range is from -40000 to 125000, in units of 1/1000 degrees centigrade. Example: A value of 23500 represents a temperature reading of 23.5 degrees C. The temperature is shown in unit of degrees centigrade, and the precision is 0.1. When the optical parameter being monitored is 'txbiasCurrent',the supported range is from 0 to 131000, in units of 1/1000 mA. Example: A value of 1000 represents a TX bias current reading of 1.0mA. The 'txbiasCurrent'is shown in unit of mA, and the precision is 0.1. When the optical parameter being monitored is 'txPower',the supported range is from -40000 to 8200, in units of 1/1000 dbm. Example: A value of 77800 represents a TX output power reading of 7.78 dBm. The 'txPower' is shown in unit of dBm, and the precision is 0.1. When the optical parameter being monitored is 'rxPower',the supported range is from -40000 to 8200, in units of 1/1000 dbm. Example: A value of 7780 represents a RX received optical power reading of 7.78 dBm. The 'rxPower' is shown in unit of dBm, and the precision is 0.1. When the optical parameter being monitored is 'XXsupplyVoltage',the supported range is from 0 to 6550, in units of 1/1000 V. Example: A value of 6000 represents a XX supply Voltage eading of 6.00V. The 'XXsupplyVoltage'is shown in unit of V, and the precision is 0.01. When the optical parameter being monitored is 'apdBiasVoltage,the supported range is from 0 to 655300 , in units of 1/1000 V . Example: A value of 600000 represents a APD BiasVoltage reading of 600.0V. The 'apdBiasVoltage' is shown in unit of V, and the precision is 0.1. When the optical parameter being monitored is 'XXsupplyCurrent',the supported range is from 0 to 6553600, in units of 1/1000 mA . Example: A value of 6000000 represents a XX supply current reading of 6000.0mA. The 'XXsupplyCurrent' is shown in unit of mA, and the precision is 0.1. When the optical parameter being monitored is 'tecCurrent',the supported range is from 0 to 6553600, in units of 1/1000 mA . Example: A value of 6000000 represents a TEC Current reading of 6000.0mA. The 'tecCurrent' is shown in unit of mA, and the precision is 0.1. When the optical parameter being monitored is 'laserWavelength,the supported range is from 0 to 3276750, in units of 1/1000 nm . Example: A value of 3000000 represents a laser wavelength reading of 3000.0nm. The 'laserWavelength'is shown in unit of nm, and the precision is 0.01.
current

Objects

NameOIDSyntaxAccessStatus
rosMgmtOpticalTransceiverNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.0
rosMgmtOpticalTransceiverObjects
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.1
rosMgmtOpticalTransceiverScalarGroup
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.1.1
rosMgmtOpticalTransceiverNotifyEnable
OBJECT-TYPE
This object specifies the generation of device notifications, enable or disable. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.1.1EnableVarread-writecurrent
rosMgmtOpticalTransceiverDDMEnable
OBJECT-TYPE
Enable or disable digitaldiagnotic on the device. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.1.2EnableVarread-writecurrent
rosMgmtOpticalTransceiverCheckPwdEnable
OBJECT-TYPE
This object specifies the status of password checking on the device, enable or disable. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.1.3EnableVarread-writecurrent
rosMgmtOpticalTransceiverPollInterval
OBJECT-TYPE
This object specifies the value of poll-interval on the device. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.1.4Integer32 (5..15)read-writecurrent
rosMgmtOpticalTransceiverCRCCheckEnable
OBJECT-TYPE
This object specifies the status of crc checking on the device, enable or disable. this object belongs to sfp and xfp.
1.3.6.1.4.1.8886.60.18.1.1.5EnableVarread-writecurrent
rosMgmtOpticalTransceiverCfgObjects
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.1.2
rosMgmtOpticalTransceiverInfoGroup
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.1.2.1
rosMgmtOpticalTransceiverInfoTable
OBJECT-TYPE
Trancetver information Table.
1.3.6.1.4.1.8886.60.18.1.2.1.1not-accessiblecurrent
rosMgmtOpticalTransceiverInfoEntry
OBJECT-TYPE
An entry in the rosMgmtOpticalTransceiverInfoTable.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1not-accessiblecurrent
rosMgmtOpticalTransceiverType
OBJECT-TYPE
This object specifies the physical type of the transceiver, such as xfp or sfp , and so on. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.1INTEGER {unknown(1), gbic(2), soldered(3), sfp(4), xbi(5), xenpak(6), xfp(7), xff(8), xfpe(9), xpak(10), x2(11), sfpj(12), qsfp(14), qsfp28(18)}read-onlycurrent
rosMgmtOpticalTransceiverConnectorType
OBJECT-TYPE
This object specifies the connector type of the transceiver, unknown, sc, db9, hssdc, bnc_tnc, fiber_coaxial_head, fiber_outlet, lc, mt_rj, mu, sg, fiber_pigtail, mpo_parallel_optic , hssdcII, copper, rj45. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.2INTEGER {unknown(1), sc(2), db9(3), hssdc(4), bnctnc(5), fibercoaxialhead(6), fiberjack(7), lc(8), mtrj(9), mu(10), sg(11), fiberpigtail(12), mpoparalleloptic(13), hssdcII(14), copper(15), rj45(16)}read-onlycurrent
rosMgmtOpticalTransceiverVendorName
OBJECT-TYPE
Vendor name of the interface. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.3OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverVendorPN
OBJECT-TYPE
Vendor part number of the interface. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.4OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverVendorSN
OBJECT-TYPE
Vendor serial number of the interface. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.5OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverMediaType
OBJECT-TYPE
Types of the fiber, single_mode, multi_modeE50, multi_mode50,multi_mode625,copper, single_modeKm,multi_modeOM3,multi_modeOM3Qsfp,multi_modeOM2Qsfp, multi_modeOM1Qsfp,multi_modeOM4Qsfp. this object belongs to xfp, sfp and qsfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.6INTEGER {singlemode(1), multimodeE50(2), multimode50(3), multimode625(4), copper(5), singlemodeKm(6), multimodeOM3(7), multimodeOM3Qsfp(8), multimodeOM2Qsfp(9), multimodeOM1Qsfp(10), multimodeOM4Qsfp(11)}read-onlycurrent
rosMgmtOpticalTransceiverTransmissionDistance
OBJECT-TYPE
The max distance which the interface could transmit, measured in meter. The object will be shown in unit of Km, and the precision is 0.001. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.7Integer32read-onlycurrent
rosMgmtOpticalTransceiverAbility
OBJECT-TYPE
This object specifies the ability of optical module digitaldiagnotic funtion. Currently, the digitaldiagnotic objects of our optical module inculde 16 parameters. this object has 32 bits, each bit represents a digital diagnotic parameter. if the bit value is 0, it means that the optical module does not provide digital diagnotic funtion for relative parameter.if the bit value is 1,it means that the optical module provides digital diagnotic funtion for relative parameter. this object belongs to xfp and sfp. The relation between parameters and bits is following: 32...16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1: The relation between parameters and bits is following: 32...16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1: | 1bit | 2bit | 3bit | 4bit | APD Bias voltage | 0(reserve) | TEC Current | Laser temperature | 5bit | 6bit |7bit | 8bit | Laser wavelength | +5V Supply voltage | +3.3V Supply voltage | +1.8V Supply voltage | 9bit | 10bit |11bit | 12bit | -5.2V Supply voltage | +5V Supply current | 0(None) | 0(None) | 13bit | 14bit | 15bit | 16bit | +3.3V Supply current | +1.8V Supply current | -5.2V Supply current | temperature | 17bit | 18bit | 19bit | 20bit ~ 32bit | Laser bias current | Rx power |Tx power | 0 But when the optical module is sfp, the 6 bit will represents the supplyVoltage of sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.8Unsigned32read-onlycurrent
rosMgmtOpticalTransceiverDDM
OBJECT-TYPE
This object specifies if the transceiver supports on digital diagnostic function, support or not support.To the xfp, the default value of this object is support. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.9INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverCalibrationType
OBJECT-TYPE
This object specifies the calibration type of the transceiver, internal, external, unknown. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.10INTEGER {unknown(1), internal(2), external(3)}read-onlycurrent
rosMgmtOpticalTransceiverRSSI
OBJECT-TYPE
This object specifies the calibration type of the transceiver, support or not support. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.11INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverVendorRev
OBJECT-TYPE
the version number of the transceiver. this object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.12OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverBRMax
OBJECT-TYPE
the min data rate of the transceiver,mesured in Mbps . this object belongs to xfp and sfp. The object will be shown in unit of Gbps, and the precision is 0.1.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.13Integer32read-onlycurrent
rosMgmtOpticalTransceiverBRMin
OBJECT-TYPE
the min data rate of the transceiver,mesured in Mbps. this object belongs to xfp and sfp.To the sfp, the min data rate value is equal to the max data rate value. The object will be shown in unit of Gbps, and the precision is 0.1.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.14Integer32read-onlycurrent
rosMgmtOpticalTransceiverWavelengthContrl
OBJECT-TYPE
if the transceiver supports on wavelength control support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.15INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverWavelength
OBJECT-TYPE
Wavelength of the interface, measured in pm(0.001nm). this object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.16Integer32read-onlycurrent
rosMgmtOpticalTransceiverWaveTolerance
OBJECT-TYPE
the range of laser wavelength from nominal wavelength,mesured in pm(0.001*nm). this object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.17Integer32read-onlycurrent
rosMgmtOpticalTransceiverCompatibility
OBJECT-TYPE
the compatibility type that the transceiver supports,such as 10GBASE-SR. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.18OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverPowerDissipation
OBJECT-TYPE
the max power dissipation of the transceiver, p1W5,p2W5,p3W5,exceed3W5. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.19INTEGER {p1W5(1), p2W5(2), p3W5(3), exceed(4)}read-onlycurrent
rosMgmtOpticalTransceiverCDR
OBJECT-TYPE
the optical module supports on CDR fundtion. support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.20INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverRefClock
OBJECT-TYPE
if the transceiver requires outside reference clock required,notrequired. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.21INTEGER {required(1), notrequired(2)}read-onlycurrent
rosMgmtOpticalTransceiverTransmitterType
OBJECT-TYPE
The transmitter type of the transceiver,such as 850 nm VCSEL. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.22INTEGER {vcsel850nm(1), vcsel1310nm(2), vcsel1550nm(3), fp1310nm(4), dfb1310nm(5), dfb1550nm(6), eml1310nm(7), eml1550nm(8), copperothers(9)}read-onlycurrent
rosMgmtOpticalTransceiverCooled
OBJECT-TYPE
The transmitter cooled type of the transceiver cooled,uncooled. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.24INTEGER {cooled(1), uncooled(2)}read-onlycurrent
rosMgmtOpticalTransceiverTunalbe
OBJECT-TYPE
The transmitter tunable type of the transceiver tunable,untunable. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.25INTEGER {tunable(1), untunable(2)}read-onlycurrent
rosMgmtOpticalTransceiverDetectorType
OBJECT-TYPE
The detector type of the transceiver pin, apd. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.26INTEGER {pin(1), apd(2)}read-onlycurrent
rosMgmtOpticalTransceiverLineLoopBack
OBJECT-TYPE
The transceiver support status of sideline loop-back control support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.27INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverXFILoopBack
OBJECT-TYPE
The transceiver support status of XFI loop-back control support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.28INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverVps
OBJECT-TYPE
This object specifies if the optical module supports on VPS support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.29INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverTxDis
OBJECT-TYPE
The transceiver support status of software control the transmitter status support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.30INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverStandby
OBJECT-TYPE
The transceiver support status of software control the standby mode. support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.31INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverInVpsLowPower
OBJECT-TYPE
The VPS in low power support status of the transceiver support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.32INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverOutVpsLowPower
OBJECT-TYPE
The VPS out low power support status of the transceiver support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.33INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverFEC
OBJECT-TYPE
The FEC support status of transceiver support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.34INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverCMU
OBJECT-TYPE
The CMU support status of transceiver support,notsupport. this object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.35INTEGER {support(1), notsupport(2)}read-onlycurrent
rosMgmtOpticalTransceiverBR
OBJECT-TYPE
This object specifies the Nominal bitrate of the transceiver, 125Mbps, 155Mbps, 622Mbps, 1.25Gbps, 2.5Gbps, 10Gbps, 100Gbps, 25Gbps. this object belongs to xfp and sfp and qsfp and qsfp28.
1.3.6.1.4.1.8886.60.18.1.2.1.1.1.36INTEGER {unknown(0), bitrate125Mbps(1), bitrate155Mbps(2), bitrate622Mbps(6), bitrate1250Mbps(12), bitrate1DOT25Gbps(13), bitrate2DOT5Gbps(19), bitrate10GbpsOr100Gbps1(103), bitrate100Gbps2(114), bitrate25Gbps(255)}read-onlycurrent
rosMgmtOpticalTransceiverDDMGroup
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.1.2.2
rosMgmtOpticalTransceiverDDMTable
OBJECT-TYPE
This table provides objects to monitor optical parameters in a network element.
1.3.6.1.4.1.8886.60.18.1.2.2.1not-accessiblecurrent
rosMgmtOpticalTransceiverDDMEntry
OBJECT-TYPE
An entry in the rosMgmtOpticalTransceiverMonTable provides objects to monitor an optical parameter at an optical interface.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1not-accessiblecurrent
rosMgmtOpticalTransceiverParameterType
OBJECT-TYPE
This object specifies the optical parameter that is being monitored in this entry. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.1OpticalParameterTypenot-accessiblecurrent
rosMgmtOpticalTransceiverParameterValue
OBJECT-TYPE
This object gives the value measured for the particular optical parameter specified by the rosMgmtOpticalMonParameterType object. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.2OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverParamHighAlarmThresh
OBJECT-TYPE
This object gives the high alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by rosMgmtOpticalParameterValue goes from below the value of this object to above the value of this object, or if the initial value of rosMgmtOpticalParameterValue exceeds the value of this object. This alarm will be indicated in the rosMgmtOpticalParamAlarmStatus object. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.3OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverParamHighWarningThresh
OBJECT-TYPE
This object is used to set a high warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by rosMgmtOpticalParameterValue goes from below the value of this object to above the value of this object, or if the initial value of rosMgmtOpticalParameterValue exceeds the value of this object. This alarm will be indicated in the rosMgmtOpticalParamAlarmStatus object. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.4OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverParamLowAlarmThresh
OBJECT-TYPE
This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by rosMgmtOpticalParameterValue goes from above the value of this object to below the value of this object, or if the initial value of rosMgmtOpticalParameterValue is lower than the value of this object. This alarm will be indicated in the rosMgmtOpticalParamAlarmStatus object .. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.5OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverParamLowWarningThresh
OBJECT-TYPE
This object is used to set a low warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by rosMgmtOpticalParameterValue goes from above the value of this object to below the value of this object, or if the initial value of rosMgmtOpticalParameterValue object is lower than the value of this object. For network elements in the status indications, this threshold violation will be indicated in the rosMgmtOpticalParamAlarmStatus object . This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.6OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverParamAlarmStatus
OBJECT-TYPE
This object is used to indicate the current status of the thresholds for the monitored optical parameter on the interface. If a threshold is currently being exceeded on the interface, the object will be set. Otherwise, the object will be set to 1. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.7INTEGER {normal(1), highalarm(2), highwarning(3), lowalarm(4), lowwarning(5)}read-onlycurrent
rosMgmtOpticalTransceiverParamAlarmLastValue
OBJECT-TYPE
This object indicates the optical parameter value at the last time a threshold related to a particular optical parameter was exceeded on the interface. If no threshold value is currently being exceeded, then the value '-1000000' is returned. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.8OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverParamAlarmLastChange
OBJECT-TYPE
This object specifies the value of sysUpTime at the last time a threshold related to a particular optical parameter was exceeded on the interface. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.9TimeTicksread-onlycurrent
rosMgmtOpticalTransceiverDDM15MinValidIntervals
OBJECT-TYPE
This object gives the number of previous 15 minute intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be n (where n is the maximum number of 15 minute intervals supported at this interface), unless the measurement was (re-)started within the last (nx15) minutes, in which case the value will be the number of previous 15 minute intervals for which the agent has some data. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.10Unsigned32 (0..96)read-onlycurrent
rosMgmtOpticalTransceiverDDM24HrValidIntervals
OBJECT-TYPE
This object gives the number of previous 24 hour intervals for which valid performance monitoring data has been stored on the interface. The max value of this object is 7, it means that the user can look up 7days history information. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.11Unsigned32 (0..7)read-onlycurrent
rosMgmtOpticalTransceiverDDMValidStatus
OBJECT-TYPE
This object indicates the parameter row is valid or invalid. The object value is 'valide' when the module is present and supporting digitaldiagnotic. The object value is 'invalid' when the module is absent, or when the module is present and not supporting digitaldiagnotic. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.12INTEGER {valid(1), invalid(2)}read-onlycurrent
rosMgmtOpticalTransceiverQsfpParameterValue
OBJECT-TYPE
This object gives the value measured for the particular optical parameter specified by the rosMgmtOpticalMonParameterType object. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.13OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpParamHighAlarmThresh
OBJECT-TYPE
This object gives the high alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by rosMgmtOpticalParameterValue goes from below the value of this object to above the value of this object, or if the initial value of rosMgmtOpticalParameterValue exceeds the value of this object. This alarm will be indicated in the rosMgmtOpticalParamAlarmStatus object. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.14OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpParamHighWarningThresh
OBJECT-TYPE
This object is used to set a high warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by rosMgmtOpticalParameterValue goes from below the value of this object to above the value of this object, or if the initial value of rosMgmtOpticalParameterValue exceeds the value of this object. This alarm will be indicated in the rosMgmtOpticalParamAlarmStatus object. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.15OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpParamLowAlarmThresh
OBJECT-TYPE
This object is used to set a low alarm threshold on the optical parameter being monitored. An alarm condition will be raised if the value given by rosMgmtOpticalParameterValue goes from above the value of this object to below the value of this object, or if the initial value of rosMgmtOpticalParameterValue is lower than the value of this object. This alarm will be indicated in the rosMgmtOpticalParamAlarmStatus object .. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.16OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpParamLowWarningThresh
OBJECT-TYPE
This object is used to set a low warning threshold on the optical parameter being monitored. A threshold crossing condition will be indicated if the value given by rosMgmtOpticalParameterValue goes from above the value of this object to below the value of this object, or if the initial value of rosMgmtOpticalParameterValue object is lower than the value of this object. For network elements in the status indications, this threshold violation will be indicated in the rosMgmtOpticalParamAlarmStatus object . This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.17OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpParamAlarmStatus
OBJECT-TYPE
This object is used to indicate the current status of the thresholds for the monitored optical parameter on the interface. If a threshold is currently being exceeded on the interface, the object will be set. Otherwise, the object will be set to 1. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.18OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpParamAlarmLastValue
OBJECT-TYPE
This object indicates the optical parameter value at the last time a threshold related to a particular optical parameter was exceeded on the interface. If no threshold value is currently being exceeded, then the value '-1000000' is returned. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.19OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpParamAlarmLastChange
OBJECT-TYPE
This object specifies the value of sysUpTime at the last time a threshold related to a particular optical parameter was exceeded on the interface. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.20OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpDDM15MinValidIntervals
OBJECT-TYPE
This object gives the number of previous 15 minute intervals for which valid performance monitoring data has been stored on the interface. The value of this object will be n (where n is the maximum number of 15 minute intervals supported at this interface), unless the measurement was (re-)started within the last (nx15) minutes, in which case the value will be the number of previous 15 minute intervals for which the agent has some data. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.21OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpDDM24HrValidIntervals
OBJECT-TYPE
This object gives the number of previous 24 hour intervals for which valid performance monitoring data has been stored on the interface. The max value of this object is 7, it means that the user can look up 7days history information. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.22OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpDDMValidStatus
OBJECT-TYPE
This object indicates the parameter row is valid or invalid. The object value is 'valide' when the module is present and supporting digitaldiagnotic. The object value is 'invalid' when the module is absent, or when the module is present and not supporting digitaldiagnotic. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.2.1.1.23OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverPMGroup
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.1.2.3
rosMgmtOpticalTransceiverPMCurrentTable
OBJECT-TYPE
This table contains performance monitoring data for the various optical parameters, collected over the current 15 minute or the current 24 hour interval.
1.3.6.1.4.1.8886.60.18.1.2.3.1not-accessiblecurrent
rosMgmtOpticalTransceiverPMCurrentEntry
OBJECT-TYPE
An entry in the rosMgmtOpticalTransceiverPMCurrentTable. It contains performance monitoring data for a monitored optical parameter at an interface, collected over the current 15 minute or the current 24 hour interval.
1.3.6.1.4.1.8886.60.18.1.2.3.1.1not-accessiblecurrent
rosMgmtOpticalTransceiverPMCurrentPeriod
OBJECT-TYPE
This object indicates whether the optical parameter values given in this entry are collected over the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.1.1.1OpticalPMPeriodnot-accessiblecurrent
rosMgmtOpticalTransceiverPMCurrentParamType
OBJECT-TYPE
This object specifies the optical parameter that is being monitored, in this entry. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.1.1.2OpticalParameterTypenot-accessiblecurrent
rosMgmtOpticalTransceiverPMCurrentMaxParam
OBJECT-TYPE
This object gives the maximum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.1.1.3OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverPMCurrentMinParam
OBJECT-TYPE
This object gives the minimum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.1.1.4OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverPMCurrentMeanParam
OBJECT-TYPE
This object gives the average value of the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.1.1.5OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverQsfpPMCurrentMaxParam
OBJECT-TYPE
This object gives the maximum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to Qsfp
1.3.6.1.4.1.8886.60.18.1.2.3.1.1.6OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpPMCurrentMinParam
OBJECT-TYPE
This object gives the minimum value measured for the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.3.1.1.7OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpPMCurrentMeanParam
OBJECT-TYPE
This object gives the average value of the monitored optical parameter, in the current 15 minute or the current 24 hour interval. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.3.1.1.8OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverPMIntervalTable
OBJECT-TYPE
This table stores performance monitoring data for the various optical parameters, collected over previous intervals. This table can have entries for one complete 24 hour interval and up to 96 complete 15 minute intervals. A system is required to store at least 4 completed 15 minute intervals. The number of valid 15 minute intervals in this table is indicated by the rosMgmtOpticalTransceiverDDM15MinValidIntervals object and the number of valid 24 hour intervals is indicated by the rosMgmtOpticalTransceiverDDM24HrValidIntervals object. when the optical module is removed from the device, the relative history records will be cleaned.
1.3.6.1.4.1.8886.60.18.1.2.3.2not-accessiblecurrent
rosMgmtOpticalTransceiverPMIntervalEntry
OBJECT-TYPE
An entry in the rosMgmtOpticalTransceiverPMIntervalTable. It contains performance monitoring data for an optical parameter, collected over a previous interval.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1not-accessiblecurrent
rosMgmtOpticalTransceiverPMIntervalPeriod
OBJECT-TYPE
This object indicates whether the optical parameter values, given in this entry, are collected over a period of 15 minutes or 24 hours. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.1OpticalPMPeriodnot-accessiblecurrent
rosMgmtOpticalTransceiverPMIntervalNumber
OBJECT-TYPE
A number between 1 and 96, which identifies the interval for which the set of optical parameter values is available. The interval identified by 1 is the most recently completed 15 minute or 24 hour interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.2Integer32 (1..96)not-accessiblecurrent
rosMgmtOpticalTransceiverPMIntervalParamType
OBJECT-TYPE
This object specifies the optical parameter that is being monitored, in this entry. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.3OpticalParameterTypenot-accessiblecurrent
rosMgmtOpticalTransceiverPMIntervalMaxParam
OBJECT-TYPE
This object gives the maximum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.4OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverPMIntervalMinParam
OBJECT-TYPE
This object gives the minimum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.5OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverPMIntervalMeanParam
OBJECT-TYPE
This object gives the average value of the measured optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.6OpticalParameterValueread-onlycurrent
rosMgmtOpticalTransceiverQsfpPMIntervalMaxParam
OBJECT-TYPE
This object gives the maximum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.7OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpPMIntervalMinParam
OBJECT-TYPE
This object gives the minimum value measured for the optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.8OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverQsfpPMIntervalMeanParam
OBJECT-TYPE
This object gives the average value of the measured optical parameter, in a particular 15 minute or 24 hour interval. This object belongs to Qsfp.
1.3.6.1.4.1.8886.60.18.1.2.3.2.1.9OCTET STRINGread-onlycurrent
rosMgmtOpticalTransceiverStatusGroup
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.1.2.4
rosMgmtOpticalTransceiverCurrentStatusTable
OBJECT-TYPE
This table stores the hard ware information and the information set by user of the transceiver. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1not-accessiblecurrent
rosMgmtOpticalTransceiverCurrentStatusEntry
OBJECT-TYPE
An entry in the rosMgmtOpticalTransceiverCurrentStatusTable. It contains performance monitoring data for an optical parameter, collected over a previous interval. This object belongs to xfp/sfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1not-accessiblecurrent
rosMgmtOpticalTransceiverHwInfoAbsStatus
OBJECT-TYPE
This object specifies if the optical module is absent present,absent. This object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.1INTEGER {absent(1), present(2)}read-onlycurrent
rosMgmtOpticalTransceiverHwInfoNRStatus
OBJECT-TYPE
This object specifies if the optical module is ready for operation. ready,notready. This object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.2INTEGER {ready(1), notready(2)}read-onlycurrent
rosMgmtOpticalTransceiverHwInfoRxLosStatus
OBJECT-TYPE
This object specifies if the optical module operation losses the receiving signal normal,loss. This object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.3INTEGER {normal(1), loss(2)}read-onlycurrent
rosMgmtOpticalTransceiverHwInfoStandby
OBJECT-TYPE
This object specifies if the optical module works under standby mode. normal,standby. This object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.4INTEGER {normal(1), standby(2)}read-writecurrent
rosMgmtOpticalTransceiverHwInfoLaser
OBJECT-TYPE
This object specifies if the optical module laser is turned on on,off. This object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.5INTEGER {on(1), off(2)}read-writecurrent
rosMgmtOpticalTransceiverWaveLengthError
OBJECT-TYPE
This object specifies error between the actual wavelength and the wavelength set by the user,measured in pm. This object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.001.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.6Integer32read-onlycurrent
rosMgmtOpticalTransceiverUserWaveLength
OBJECT-TYPE
This object specifies the wavelength value of the optical module set by user,measured in pm. This object belongs to xfp. The object will be shown in unit of nm, and the precision is 0.01.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.7Integer32 (0..3276800)read-writecurrent
rosMgmtOpticalTransceiverUserDataRate
OBJECT-TYPE
This object specifies the data rate of the optical module set by user,measured in Mbps. This object belongs to xfp. The object will be shown in unit of Gbps, and the precision is 0.1.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.8Integer32 (9500..12500)read-writecurrent
rosMgmtOpticalTransceiverUserLineLoopBack
OBJECT-TYPE
This object specifies if the sideline loop-back is tuned on , user can change the loop back mode through the object. normal,lineLoopback. This object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.9INTEGER {normal(1), lineLoopback(2)}read-writecurrent
rosMgmtOpticalTransceiverUserXFILoopBack
OBJECT-TYPE
This object specifies if the XFI loop-back is tuned on user can change the loop back mode through the object. normal,xfiLoopback. This object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.10INTEGER {normal(1), xfiLoopback(2)}read-writecurrent
rosMgmtOpticalTransceiverPortNotifyEnable
OBJECT-TYPE
This object specifies the generation of a port notifications, enable or disable. This object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.11EnableVarread-writecurrent
rosMgmtOpticalTransceiverPortDDMEnable
OBJECT-TYPE
This object specifies the status of digitaldiagnotic on a port, enable or disable. This object belongs to xfp and sfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.12EnableVarread-writecurrent
rosMgmtOpticalTransceiverPortCheckPwdEnable
OBJECT-TYPE
This object specifies the status of password checking on a port, enable or disable. This object belongs to xfp.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.13EnableVarread-writecurrent
rosMgmtOpticalTransceiverTxFaultCount
OBJECT-TYPE
This object specifies the number of tx-fault signals.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.14Integer32read-onlycurrent
rosMgmtOpticalTransceiverTxFaultCountClear
OBJECT-TYPE
This object specifies clear the statistcs of tx-fault signals.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.15TruthValueread-writecurrent
rosMgmtOpticalTransceiverSpecificationCheckStatus
OBJECT-TYPE
This object specifies the check status, accord(0)specifies the optical module accord with industrial. not-accord(2) specifies the optical module not accord with industrial.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.16INTEGER {none(0), accord(1), notaccord(2)}read-onlycurrent
rosMgmtOpticalTransceiverTxFaultStatus
OBJECT-TYPE
This object specifies the tx-fault status.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.17INTEGER {normal(1), txfault(2)}read-onlycurrent
rosMgmtOpticalTransceiverPortCRCCheckEnable
OBJECT-TYPE
This object specifies the status of CRC checking on a port, enable or disable. This object belongs to sfp and xfp
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.18EnableVarread-writecurrent
rosMgmtOpticalTransceiverBaseCRCCheckStatus
OBJECT-TYPE
This object specifies the result of base information crc checking.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.19INTEGER {none(0), pass(1), notpass(2)}read-onlycurrent
rosMgmtOpticalTransceiverStaticDdmCRCCheckStatus
OBJECT-TYPE
This object specifies the result of static ddm crc checking.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.20INTEGER {none(0), pass(1), notpass(2)}read-onlycurrent
rosMgmtOpticalTransceiverDynamicDdmCRCCheckStatus
OBJECT-TYPE
This object specifies the result of Dynamic ddm crc checking.
1.3.6.1.4.1.8886.60.18.1.2.4.1.1.21INTEGER {none(0), pass(1), notpass(2)}read-onlycurrent
rosMgmtOpticalTransceiverConformance
OBJECT-IDENTITY
1.3.6.1.4.1.8886.60.18.2

Notifications

NameOIDStatus
rosMgmtOpticalTransceiverAbsentTrap
NOTIFICATION-TYPE
This notification is sent when the optical module is removed from the device. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.1current
rosMgmtOpticalTransceiverPresentTrap
NOTIFICATION-TYPE
This notification is sent when the optical module is plugged into the device. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.2current
rosMgmtOpticalTransceiverNRAlarmTrap
NOTIFICATION-TYPE
This notification is sent when the transmitted or received data of optical module is invalid. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.3current
rosMgmtOpticalTransceiverNRNormalTrap
NOTIFICATION-TYPE
This notification is sent when the transmitted or received data of optical module is valid. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.4current
rosMgmtOpticalTransceiverRxLosAlarmTrap
NOTIFICATION-TYPE
This notification is sent when the optical module receiving signal is lost. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.5current
rosMgmtOpticalTransceiverRxLosNormaTrap
NOTIFICATION-TYPE
This notification is sent when the optical module receiving signal is back to normal. This notification may be suppressed under the following conditions: - depending on the value of the raisecomOpticalNotifyEnable and raisecomOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.6current
rosMgmtOpticalTransceiverParamAlarmTrap
NOTIFICATION-TYPE
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.7current
rosMgmtOpticalTransceiverParamAlarmNormalTrap
NOTIFICATION-TYPE
This notification is sent when the optical module parameter value dicrease to under the high alarm threshold or increase to above the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.8current
rosMgmtOpticalTransceiverParamWarningTrap
NOTIFICATION-TYPE
This notification is sent when the optical module parameter value increase to above the high warning threshold or dicrease to under the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.9current
rosMgmtOpticalTransceiverParamWarningNormalTrap
NOTIFICATION-TYPE
This notification is sent when the optical module parameter value dicrease to under the high warning threshold or increase to above the low warning threshold. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.10current
rosMgmtOpticalTransceiverLaserBackLightAlarmTrap
NOTIFICATION-TYPE
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.11current
rosMgmtOpticalTransceiverLaserBackLightAlarmNormalTrap
NOTIFICATION-TYPE
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.12current
rosMgmtOpticalTransceiverLaserLifeAlarmTrap
NOTIFICATION-TYPE
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.13current
rosMgmtOpticalTransceiverLaserLifeAlarmNormalTrap
NOTIFICATION-TYPE
This notification is sent when the optical module password cheching is successful. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.14current
rosMgmtOpticalTransceiverParamLowAlarmTrap
NOTIFICATION-TYPE
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.15current
rosMgmtOpticalTransceiverParamLowAlarmNormalTrap
NOTIFICATION-TYPE
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.16current
rosMgmtOpticalTransceiverParamLowWarningTrap
NOTIFICATION-TYPE
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.17current
rosMgmtOpticalTransceiverParamLowWarningNormalTrap
NOTIFICATION-TYPE
This notification is sent when the optical module parameter value increase to above the high alarm threshold or dicrease to under the low alarm threshold. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.18current
rosMgmtOpticalTransceiverTxFaultTrap
NOTIFICATION-TYPE
This notification is sent when the SFP optical module occures Tx-fault signal. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.19current
rosMgmtOpticalTransceiverTxNormalTrap
NOTIFICATION-TYPE
This notification is sent when the SFP optical module cancels the Tx-fault signal. This notification may be suppressed under the following conditions: - depending on the value of the rosMgmtOpticalNotifyEnable and rosMgmtOpticalPortNotifyEnable objects.
1.3.6.1.4.1.8886.60.18.0.20current