PROXIM-MIB

TEXTUAL-CONVENTION

The DisplayString20 textual convention is used to define a string that can consist of 0 - 20 alphanumeric characters.

TEXTUAL-CONVENTION

The DisplayString32 textual convention is used to define a string that can consist of 0 - 32 alphanumeric characters.

TEXTUAL-CONVENTION

The DisplayString32 textual convention is used to define a string that can consist of 0 - 55 alphanumeric characters this textual convention is used for Temperature log messages.

TEXTUAL-CONVENTION

The DisplayString80 textual convention is used to define a string that can consist of 0 - 80 alphanumeric characters.

TEXTUAL-CONVENTION

An Interface Bitmask used to enable or disable access or functionality of an interface in the system. Each bit in this object represents a network interface in the system consistent with the ifIndex object in MIB-II. The value for this object is interpreted as a bitfield, where the value of 1 means enabled. Examples of Usage: 1. For a system with the following interfaces : - Ethernet If = 1 - Loopback If = 2 - Wireless If 0 VAP 0 = 3 - Wireless If 0 VAP 1 = 4 - Wireless If 0 VAP 2 = 5 - Wireless If 0 VAP 3 = 6 - Wireless If 1 VAP 0 = 7 - Wireless If 1 VAP 1 = 8 - Wireless If 1 VAP 2 = 9 - Wireless If 1 VAP 3 = 10 Interface Bitmask usage: - 00000000 (0x00): All Interfaces disabled - 00000001 (0x01): Ethernet If enabled - 00000010 (0x02): Wireless If 0 VAP 0 enabled - 00000100 (0x03): Wireless If 0 VAP 1 enabled - 00001000 (0x04): Wireless If 0 VAP 2 enabled - 00010000 (0x06): Wireless If 0 VAP 3 enabled TBD: This has to be re-considered Note: The software loopback interface bit is ignored in the usage of the interface bitmask object.

TEXTUAL-CONVENTION

The status textual convention is used to enable or disable functionality or a feature.

TEXTUAL-CONVENTION

The status textual convention is used to activate, deactivate, and delete a table row.

TEXTUAL-CONVENTION

This represents a textual convention for password feilds.

TEXTUAL-CONVENTION

This represents a textual convention for password feilds.

TEXTUAL-CONVENTION

A 12-bit VLAN ID used in the VLAN Tag header.

TEXTUAL-CONVENTION

The WEPKeyType textual convention is used to define the object type used to configured WEP Keys.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table contains information on the properties and capabilities of the wireless interface(s) present in the device.

OBJECT-TYPE

This parameter represents the entry in the wireless interface properties table.

OBJECT-TYPE

This parameter represents a unique value for each Wireless interface in the system and is used as index to this table.

OBJECT-TYPE

This parameter is used to provide the status of the Wireless Radio interface. Select (1) to enable the wireless interface and (2) to disable the wireless interface.

OBJECT-TYPE

This parameter is used to set the wireless NIC Operational mode. Depending on the wireless NIC in the device different wireless operational modes can be configured. The object wirelessIfSupportedOperationalMode shows the supported modes and the possible supported modes for AP products: dot11b(1), dot11g(2), dot11ng(3), dot11a(4), dot11na(5)

OBJECT-TYPE

This parameter is used to set the wireless supported Operational mode.

OBJECT-TYPE

This parameter represents the current bandwidth that Wireless is currently operating on. It is represented in MHz

OBJECT-TYPE

This parameter represents the channel bandwidths that a wireless can support.

OBJECT-TYPE

This parameter is used to configure the auto channel selection for wireless interface. Select (1) to enable the auto channel selection and (2) to disable the auto channel selection.

OBJECT-TYPE

This parameter represents the user configured channel that the radio is configured to operate in. Note: It is possible that the currently active channel is different. To find the current active/operational channel refer to wirelessIfCurrentActiveChannel.

OBJECT-TYPE

This parameter represents the channels that wireless can support.

OBJECT-TYPE

This parameter is used to configure the value for Auto Rate Selection for the wireless interface. Select (1) to enable the Auto Rate selection and (2) to disable the Auto Rate selection.

OBJECT-TYPE

This parameter represents the number of rates transmitted for wireless.

OBJECT-TYPE

This parameter represents the number of rates supported for wireless.

OBJECT-TYPE

This parameter represents the maximum threshold for VAP RTS (Request To Send). The maximum threshold can be configured up to 2346.

OBJECT-TYPE

This parameter represents the time interval that a beacon takes for getting transmitted for wireless VAP. By default, the value is set to 100 ms.

OBJECT-TYPE

This parameter represents the cell size that the transmitted power controls. It is measured in dBm. Please check the wirelessIfActiveTPC for current active TPC.

OBJECT-TYPE

This parameter represents the cell size of the wireless. By default, the cell size is configured to large. Select (1) for Small cell size, (2) for Medium cell size and (3) for Large cell size.

OBJECT-TYPE

This parameter represents the delivery traffic indication map period. This is the interval between the transmission of multicast frames on the wireless inteface. It is expressed in the Beacon messages. The recommended default value for this parameter is 1.

OBJECT-TYPE

This parameter is used to configure the antenna gain.

OBJECT-TYPE

This parameter represents the current active channel that wireless radio is operating on. It may be different from the configured channel represented by wirelessIfCurrentOperatingChannel.

OBJECT-TYPE

This parameter represents the density of the satellites for the BSU. It configures the BSU to accomodate the satellites for the specified range.

OBJECT-TYPE

This parameter is used to set the wireless NIC Operational mode for Tsunami Multi Point Products.

OBJECT-TYPE

This parameter is used to configure the DFS channel wait time.

OBJECT-TYPE

This parameter shows the active cell size that the transmitted power controls. It is measured in dBm

OBJECT-TYPE

This parameter represents the minimum number of satellites reporting RADAR for BSU to switch to a new best channel/frequency. The default value is (0) that indicates BSU to never switch to a new best channel/frequency for any number of satellites reporting RADAR.

OBJECT-TYPE

This parameter is used to configure the status of the DFS for SU. Configuring this parameter for BSU will not affecte BSU Status. 1 to enable the DFS, 2 to disable the DFS.

OBJECT-TYPE

This table holds the wireless11n configurations.

OBJECT-TYPE

This parameter represents the entry for wireless11n properties table.

OBJECT-TYPE

This parameter represents index to the wireless interface 11n table and this represents the wireless radios.

OBJECT-TYPE

This parameter is used define the AMPDU status for wireless 11n interface. Select 1 to enable and 2 to disable the AMPDU status.

OBJECT-TYPE

This parameter represents the Agregated MAC Protocol Data Unit (AMPDU) frames that are transmitted. It can be configured up to 64 frames.

OBJECT-TYPE

This parameter is used to configure the maximum AMPDU frame size (in bytes) that can be transmitted.

OBJECT-TYPE

This parameter is used define the AMSDU status for wireless 11n interface. Select 1 to enable and 2 to disable the AMSDU status.

OBJECT-TYPE

This parameter shows the maximum AMSDU frame size (in bytes) that can be transmitted.

OBJECT-TYPE

This parameter is used to configure the frequency extension for the wireless interface. Select 1 to configure the UpperExtensionChannel and 2 to configure the LowerExtensionChannel.

OBJECT-TYPE

This parameter is used to configure the guard interval for the wireless interface. Select 1 for short guard interval as 400 nano seconds and 2 for full guard interval as 800 nano seconds.

OBJECT-TYPE

This parameter enables the transmission antennas. This is configured as bit-mask. Eg: 3 - 011 (binary value) - first and second antennas are enabled. 7 - 111 (binary value) - all three are enabled.

OBJECT-TYPE

This parameter enables the receiving antennas. This is configured as bit-mask. Eg: 3 - 011 (binary value) - first and second antennas are enabled. 7 - 111 (binary value) - all three are enabled.

OBJECT-TYPE

This parameter is used to select the number of spatial streams for 11n.

OBJECT-TYPE

This parameter shows the number of supported Tx antennas.

OBJECT-TYPE

This parameter shows the number of supported Rx antennas.

OBJECT-TYPE

This table holds the wireless VAP (virtual access point) configurations.

OBJECT-TYPE

This parameter represents the entry for the wireless VAP table.

OBJECT-TYPE

This parameter is used to configure the wireless VAP table. Select 1 represents Wifi0 (radio-0) and 2 represents Wifi1 (radio-1).

OBJECT-TYPE

This parameter represents the VAPs and used as secondary index to this table.

OBJECT-TYPE

This parameter is used to configure the type of VAP. Select 1 for AP.

OBJECT-TYPE

This parameter is used to represent the wireless card SSID name (wireless network name).

OBJECT-TYPE

This parameter represents the MAC address for the VAP BSSID.

OBJECT-TYPE

This parameter is used to configure the status of the broadcast wireless VAP SSID. A single entry in the SSID table can be enabled to broadcast SSID in beacon messages. Select 1 to enable, 2 to disable

OBJECT-TYPE

This parameter is used to configure the fragmentation threshold for the wireless VAP. By default, the value is set to 2346.

OBJECT-TYPE

This parameter allows you to configure the Security profile name for Wireless VAP.

OBJECT-TYPE

This parameter allows you to configure the RADIUS profile name for Wireless VAP.

OBJECT-TYPE

This parameter is used to represent the VLAN ID for the wireless VAP. Select any value between 1 - 4094 to tag the VLAN ids and -1 to untag the VLAN ids.

OBJECT-TYPE

This parameter is used to configure the VLAN priority for Wireless VAP. By default the value is set to 0.

OBJECT-TYPE

This parameter is used to configure the profile name for the Wireless VAP QoS.

OBJECT-TYPE

This parameter is used to enable or disable the MAC access control list.

OBJECT-TYPE

This parameter is used to enable or disable the MAC ACL for Radius Profiles

OBJECT-TYPE

This parameter is used to enable or disable the Radius Accounting Stats capture.

OBJECT-TYPE

This parameter is used to configure the status of the VAP. Select 1 to enable the VAP, 2 to disable the VAP and 3 to delete the VAP.

OBJECT-TYPE

This table holds the wireless WORP protocol configurations

OBJECT-TYPE

This object represents the entry for the wireless WORP table

OBJECT-TYPE

This parameter represents the radio for which the WORP is enabled and index to the wirelessIfWORPTable.

OBJECT-TYPE

This parameter displays the worp mode of operation.

OBJECT-TYPE

This parameter represents the name of the BSU for which it can register. This configuration is valid only on SU. If this field is empty then SU is allowed to register with any BSU.

OBJECT-TYPE

This parameter represents the name of the Network of the WORP Interface.

OBJECT-TYPE

This parameter represents the maximum number of SUs allowed to register on this BSU. This configuration is valid only on BSU.

OBJECT-TYPE

This parameter represents to maximum size of a frame sent from the WORP interface.

OBJECT-TYPE

This parameter represents the status of bundling multiple ethernet frames in one single WORP Jumbo frame

OBJECT-TYPE

This parameter represents the status of sleep mode. This Configuration is valid only on BSU. If there is no data available to transfer b/w BSU & SU, BSU will keep the SU state in sleep state and polls that particular SU for every 4 seconds to just to maintain the WORP link.

OBJECT-TYPE

This parameter enables WORP protocol to allow each side, BSU or SU, to send a burst of multiple data messages instead of a single data message.

OBJECT-TYPE

This parameter represents the registration procedure timeout period for WORP interface.

OBJECT-TYPE

This parameter represents the number of times the same worp frame need to be re-Transmitted, if it is not acknowledged by the peer.

OBJECT-TYPE

This parameter represents the WORP interface transmission rate. Please check the object wirelessIfWORPSupportedTxRate for supported rates.

OBJECT-TYPE

This parameter displays the supported transmission rate based on Channel Bandwdith, Guard Interval and Number of Spacial Streams configuration.

OBJECT-TYPE

This parameters represents the Bandwidth limit on Input direction. Default limit & maximum limit are based on the license file.

OBJECT-TYPE

This parameter represents the Bandwidth limit on Output direction. Default limit & maximum limit are based on the license file.

OBJECT-TYPE

This parameter represents the bandwidth limit type - shaping or policing.

OBJECT-TYPE

This parameter allows to configure the Security profile for the WORP interface based on the index of the profile name and this is Valid only on BSU.

OBJECT-TYPE

This parameter allows to configure the Radius profile for the WORP interface based on the index of the profile name and this is Valid only on BSU..

OBJECT-TYPE

This parameter is used to enable or disable the MAC access control list. This configuration is Valid only on BSU.

OBJECT-TYPE

This parameter is used to enable or disable the MAC ACL for Radius Profiles. This configuration is Valid only on BSU.

OBJECT-TYPE

This parameter is used to enable or disable the Radius Accounting Stats capture. This configuration is Valid only on BSU and currently this is not accessible.

OBJECT-TYPE

This parameter represents the MAC address of the wireless interface card.

OBJECT-TYPE

This parameter enables WORP protocol to allow each side, BSU or SU, to send a burst of multiple data messages based on QOS priority instead of a single data message.

OBJECT-TYPE

This table holds the WORP DDRS (Dynamic Data Rate Selection) feature configurations.

OBJECT-TYPE

This parameter represents the entry for DDRS table.

OBJECT-TYPE

This parameter represents the index for the DDRS table and indirectly represent the wireless interface index.

OBJECT-TYPE

This parameter is used to enable/disable the DDRS feature for the interface.

OBJECT-TYPE

This default data rate shall be used as WORP default data rate only when the DDRS is enabled. The rates defined in wirelessIfWORPTxRate are used as default.

OBJECT-TYPE

This parameter is used to limit the maximum possible data rate that is set by DDRS.

OBJECT-TYPE

This parameter is used to specify the average SNR threshold for data rate increase. The value should be in dB and in the range of 0..50 dB.

OBJECT-TYPE

This parameter is to specify minimum required SNR threshold for data rate increase. The value should be in dB and in the range 0..50 dB.

OBJECT-TYPE

This parameter is to specify minimum required SNR threshold for data rate decrease. The value should be in dB and in the range 0..50 dB.

OBJECT-TYPE

This object specifies the threshold percentage of retransmissions for DDRS data rate increase.

OBJECT-TYPE

This object specifies the threshold percentage of retransmissions for DDRS data rate decrease.

OBJECT-TYPE

This object specifies the aggressiveness of the ddrs algorithm.

OBJECT-TYPE

This object specifies the Mimo Chain Balance threshold.

OBJECT-TYPE

This object specifies the Rate Backoff Interval.

OBJECT-TYPE

This object specifies the Rate Blacklist Interval.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-IDENTITY

OBJECT-TYPE

This table shows the ethernet interface(s) properties for the device.

OBJECT-TYPE

This parameter represents the entry for the Ethernet Interface Properties table.

OBJECT-TYPE

This parameter represents the physical interface and used as index to this table.

OBJECT-TYPE

This parameter represents the MAC address for the ethernet interface.

OBJECT-TYPE

This parameter shows the supported speeds for the ethernet interface.

OBJECT-TYPE

This parameter shows the supported transmit modes of the ethernet interface.

OBJECT-TYPE

This parameter is used to configure the Transmit Mode and speed of the ethernet interface.

OBJECT-TYPE

This parameter is used to display the supported modes on ethernet interface.

OBJECT-TYPE

This parameter is used to configure the admin status for the ethernet interface.

OBJECT-TYPE

This parameter is used to configure AutoShutDown for the ethernet interface. i.e. Ethernet interface will be automatically UP/DOWN depending upon the wireless link

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to specify the security configuration for the wireless interface(s) in the access point.

OBJECT-TYPE

This parameter represents an entry in the wireless security configuration table. This table supports up to 8 entries.

OBJECT-TYPE

This parameter is used as index to the wireless security configuration table.

OBJECT-TYPE

This paramater represents user defined profile name for security configuration.

OBJECT-TYPE

This parameter is used to configure the security authentication mode for wireless. Select (1) - None (no security), (2) - WEP (Wired Equivalent Privacy), (3) - PSK (Pre-shared key), (4) - dotlx (802.1x authentication) and (5) - worp (Wireless Outdoor Router Protocol).

OBJECT-TYPE

This parameter represents the encryption key index that is used to encrypt data that is sent via wireless interface(s).

OBJECT-TYPE

This parameter represents the key 1 used for wireless security configuration. The key lengths 5/13/16 in ASCII or 10/26/32 in HEXADECIMAL configures the WEP(64/128/152-bit) encryption respectively. The key lengths 16 in ASCII or 32 in HEXADECIMAL configures the TKIP(128-bit) or AES-CCM(128-bit) encryption.

OBJECT-TYPE

This parameter is used configure the length of the security key. Select WEP64 if you want to have a security key for 64 characters or WEP128 for security key length of 128 characters.

OBJECT-TYPE

This parameter is used to configure the encryption key type for wireless security. Select 0 for no security 1 for WEP, 2 for WPA (TKIP), 3 for WPA2(AES), 4 for WPA/WPA2 (AES-TKIP) 5 for WPA2 (AES-CCM). 6 for TKIP -- Used only for TMP/QB products 7 for AES-CCM -- Used only for TMP/QB products.

OBJECT-TYPE

This parameter is used to configure the pre-share key. The default key is 123456789. This parameter is logically write-only. Reading this variable shall return astericks

OBJECT-TYPE

This parameter represents the key re-negotiation time in case of dynamic WEP, WPA/WPA-2 (personal/enterprise) security mechanisms.

OBJECT-TYPE

This parameter is used to configure the entry status of wireless security configuration table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This parameter represents a secret password of an SU that tallies with the BSU's password for authentic registration.

OBJECT-TYPE

This parameter represents the key 2 used for wireless security configuration. The key lengths 5/13/16 in ASCII or 10/26/32 in HEXADECIMAL configures the WEP(64/128/152-bit) encryption respectively. The key lengths 16 in ASCII or 32 in HEXADECIMAL configures the TKIP(128-bit) or AES-CCM(128-bit) encryption.

OBJECT-TYPE

This parameter represents the key 3 used for wireless security configuration. The key lengths 5/13/16 in ASCII or 10/26/32 in HEXADECIMAL configures the WEP(64/128/152-bit) encryption respectively. The key lengths 16 in ASCII or 32 in HEXADECIMAL configures the TKIP(128-bit) or AES-CCM(128-bit) encryption.

OBJECT-TYPE

This parameter represents the key 4 used for wireless security configuration. The key lengths 5/13/16 in ASCII or 10/26/32 in HEXADECIMAL configures the WEP(64/128/152-bit) encryption respectively. The key lengths 16 in ASCII or 32 in HEXADECIMAL configures the TKIP(128-bit) or AES-CCM(128-bit) encryption.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains the radius server configuration profiles.

OBJECT-TYPE

This parameter represents the entry for the radius server profile table.

OBJECT-TYPE

This parameter represents the user defined profiles for RADIUS Server.

OBJECT-TYPE

This parameter represents the user defined secondary profiles for RADIUS server. Maximum profiles are 4.

OBJECT-TYPE

This parameter represents the RADIUS Server profile type. Select (1) for Primary Authentication Server, (2) for Secondary Authentication Server, (3) for Primary Accounting Server, and (4) for Secondary Accounting Server.

OBJECT-TYPE

This parameter is used to specify the RADIUS Server IP Address. Its default value is 169.254.128.133.

OBJECT-TYPE

This parameter represents the RADIUS server authentication port and the default value is 1812.

OBJECT-TYPE

This parameter represents the shared secret between the RADIUS server and client. It is logically treated as write-only and should return the information in asterisks.

OBJECT-TYPE

This parameter is used to configure the entry status of RADIUS server profile table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This table contains the radius support profile table configurations.

OBJECT-TYPE

This parameter represents the entry for the radius support profile table.

OBJECT-TYPE

This parameter represents the index for the radius support profile table. Each index corresponds to the one profile name in the radius server profile table

OBJECT-TYPE

This parameter represents the RADIUS profile name, only one profile is supported.

OBJECT-TYPE

This parameter represents the number of times the radius request message to be sent to RADIUS server after the expiry of response time.

OBJECT-TYPE

This parameter represents the wait time in the RADIUS client for the response message from RADIUS server.

OBJECT-TYPE

The parameter represents the time interval within which the reauthentication of the 802.1x enabled station happens.

OBJECT-TYPE

This parameter is used to configure the entry status of RADIUS supported profile table. It can be configured as active(enable) -1, notInService(disable) - 2

OBJECT-IDENTITY

OBJECT-TYPE

This table contains the MAC access control profile configurations.

OBJECT-TYPE

This parameter represents the entry for the MAC access control profile table.

OBJECT-TYPE

User defined profiles for MAC Access Control List. Max. number of profiles are 16.

OBJECT-TYPE

This parameter represents the unique name MAC ACL profile.

OBJECT-TYPE

This parameter is used o configure the type of MAC ACL profile. Select (1) to allow and (2) to deny.

OBJECT-TYPE

This parameter is used to configure the status of the security MAC ACL profile. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This table holds MAC access control list addresses.

OBJECT-TYPE

This parameter represents the entry for the MAC access control list address table.

OBJECT-TYPE

This parameter represents the user defined profiles for MAC ACL Address. Max. profiles are 16 profiles.

OBJECT-TYPE

This parameter represents the user defined secondary profiles for MAC ACL Address. Maximum entries are 64 -- one entry per station

OBJECT-TYPE

This parameter represents the valid MAC address for MAC ACL.

OBJECT-TYPE

This parameter displays a valid comment for MAC ACL Address.

OBJECT-TYPE

This parameter is used to configure the status of the security MAC ACL Address. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This table holds the various profiles for QOS (quality of service) configuration.

OBJECT-TYPE

This parameter represents the entry for the qos profile table.This table supports one entry.

OBJECT-TYPE

This parameter represents user defined profiles for Quality of Service (QoS).

OBJECT-TYPE

This parameter displays the name of the QoS profile that has been assigned.

OBJECT-TYPE

This parameter displays the QoS Policy profile name.

OBJECT-TYPE

This parameter displays the name for QoS EDCA profile.

OBJECT-TYPE

This parameter is used to configure the status of the QoS profile ACK.

OBJECT-TYPE

This table contains the QOS policy configurations.

OBJECT-TYPE

This parameter represents the entry for the qos policy table.

OBJECT-TYPE

This parameter represents user defined profiles for QoS Policy list.

OBJECT-TYPE

This parameter represents user defined secondary profiles. They are inbound layer2 -1, inbound layer3 -2, outbound layer2 -3 and outbound layer3 -4

OBJECT-TYPE

This parameter displays the QoS policy name.

OBJECT-TYPE

This parameter configures the QoS Policy type. They can be configured as the following: inbound layer2(1), inbound layer3(2), outbound layer2(3) and outbound layer3(4)

OBJECT-TYPE

This parameter is used as the primary index to the QoS 802.1D to 802.1p mapping table.

OBJECT-TYPE

This parameter is used to enable or disable QoS Policy markings. Select (1) to enable, (2) to disable, and (3) for not supported option.

OBJECT-TYPE

The parameter is used to configure the QoS Policy Table status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This table holds the wireless QOS EDCA (enhanced distributed channel access) configurations.

OBJECT-TYPE

This parameter represents the entry for the wireless QOS EDCA table.

OBJECT-TYPE

This parameter is user defined profiles for Wireless QoS EDCA. Max profile that user can define is 1.

OBJECT-TYPE

This parameter represents the user defined secondary profiles for Wireless QoS EDCA. Maximum profiles are 4. BK -1 (back ground), BE -2 (best effort), VI -3 (video), VO -4 (voice)

OBJECT-TYPE

This parameter displays the name for the Wireless QoS EDCA profile.

OBJECT-TYPE

This parameter is used to configure the CW(Contention Window) min value for the wireless QoS EDCA profile. It can be configured up to 255 value. If this value is configured lower, then this increases the priority of the access category.

OBJECT-TYPE

This parameter is used to configure the CW(Contention window) Max value for the wireless QoS EDCA profile. This value can be configured up to 65535. If this value id confiured to a lower value, then this increases the priority of access category.

OBJECT-TYPE

This parameter is used to configure the AIFSN (Arbitrary Inter Frame Space Number) value for the wireless QoS EDCA profile. It can be configured up to 15. If this value is configured lower,then this increases the priority of the access category.

OBJECT-TYPE

This parameter is used to configure TXOP(transmission oppurtunities) value for Wireless QoS EDCA. The values can be configured up to 65535. If this value for this parameter is configured lower, then this decreases the priority of the access category.

OBJECT-TYPE

This parameter is used to enable or disable the value for Addmission Control Mandatory. If ACM value is set to enable for a particular access category, then certain procedures needs to followed for using that access category.

OBJECT-TYPE

This parameter is used to configure the minimum value for APCWmin. It can be configured upto 32767.

OBJECT-TYPE

This parameter is used to configure the maximum value for APCWmax. It can be configured upto 32767.

OBJECT-TYPE

This parameter is used to configure the value fo APAIFSN(Arbitration Inter-Frame Space Number). The value for the APAIFSN can be configured up to 15

OBJECT-TYPE

This parameter is used to configure the APTXOP (transmission oppurtunities) for the QoS EDCA profile. If the value is set to 0, then only one MPDU or MSDU can be transmitted

OBJECT-TYPE

This parameter is used to configure the APACM for the QoS EDCA profile. Select (1) to enable the profile and (2) to disable it.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure Quality of Service mappings between 802.1D and 802.1p priorities.

OBJECT-TYPE

This parameter represents entries in the QoS 802.1D to 802.1p Mapping Table.

OBJECT-TYPE

This parameter is used as the primary index to the QoS 802.1D to 802.1p mapping table. This is based on the QoS profile.

OBJECT-TYPE

This parameter is used to specify the 802.1d priority and is used as the secondary index to the 802.1D to 802.1p mapping table.

OBJECT-TYPE

This parameter is used to specify the 802.1D priority to be mapped to a 802.1p priority

OBJECT-TYPE

This table is used to configure Quality of Service mappings between 802.1D to IP DSCP (Differentiated Services Code Point) priorities.

OBJECT-TYPE

This parameter represents entries in the 802.1D to IP DSCP Mapping Table.

OBJECT-TYPE

This parameter is used as the primary index to the 802.1D to IP DSCP mapping table.

OBJECT-TYPE

This parameter is used to specify the 802.1D priority and is used as the secondary index to the 802.1D to IP DSCP mapping table.

OBJECT-TYPE

This parameter is used to specify IP DSCP lower limit.

OBJECT-TYPE

This parameter is used to specify IP DSCP upper limit.

OBJECT-IDENTITY

OBJECT-TYPE

This Table holds the MAC Address details for Packet Identification Rule Clasification.

OBJECT-TYPE

This parameter represents the entry for the worpQoSPIRMacTable.

OBJECT-TYPE

This parameter specifies the index number of the entry in the table.

OBJECT-TYPE

This parameter specifies the MAC Address which can be used for PIR classification.

OBJECT-TYPE

This parameter specifies the MAC Address mask for the worpQoSPIRMacAddr.

OBJECT-TYPE

This parameter specifies the comment for the mac entry.

OBJECT-TYPE

This parameter is used to configure the worpQoSPIRMacTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This Table holds the IP Address details for PIR (Packet Identification Rule) Clasification.

OBJECT-TYPE

This parameter represents the entry for the worpQoSPIRIPTable.

OBJECT-TYPE

This parameter specifies the index number of the entry in the table.

OBJECT-TYPE

This parameter specifies the IP Address which can be used for PIR classification.

OBJECT-TYPE

This parameter specifies the Subnet Mask for the worpQoSPIRIPAddr.

OBJECT-TYPE

This parameter specifies the comment for the IP Address entry.

OBJECT-TYPE

This parameter is used to configure the worpQoSPIRIPTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This Table holds the TCP/UDP Port details for PIR (Packet Identification Rule) Clasification.

OBJECT-TYPE

This parameter represents the entry for the worpQoSPIRPortTable.

OBJECT-TYPE

This parameter specifies the index number of the entry in the table.

OBJECT-TYPE

This parameter specifies the Starting TCP/UDP Port Number which can be used for PIR classification.

OBJECT-TYPE

This parameter specifies the Ending TCP/UDP Port Number which can be used for PIR classification.

OBJECT-TYPE

This parameter specifies the comment for the TCP/UDP Port entry.

OBJECT-TYPE

This parameter is used to configure the worpQoSPIRPortTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6.

OBJECT-TYPE

This Table holds the Mapping information between PIR MAC Table entries, PIR IP Table entries, PIR Port Table entries with PIR Table.

OBJECT-TYPE

This table represents the entry for the worpQoSPIRMapTable.

OBJECT-TYPE

This parameter specifies the index number of the entry in the table.

OBJECT-TYPE

This parameter specifies the PIR Rule name corresponds to this index.

OBJECT-TYPE

This parameter specifies the Source MAC Address Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.

OBJECT-TYPE

This parameter specifies the Destination MAC Address Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.

OBJECT-TYPE

This parameter specifies the Source IP Address Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.

OBJECT-TYPE

This parameter specifies the Destination IP Address Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.

OBJECT-TYPE

This parameter specifies the Source TCP/UDP Port Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.

OBJECT-TYPE

This parameter specifies the Destination TCP/UDP Port Classification for the PIR Rule. This is a display string consists of index number of the PIR MAC Table entries with comma seperated. Value 0 indicates that this list is disabled.

OBJECT-TYPE

This Table holds the Packet Identification Rule(PIR) information for QoS feature.

OBJECT-TYPE

This parameter represents the entry for the worpQoSPIRTable.

OBJECT-TYPE

This parameter specifies the index number of the entry in the table.

OBJECT-TYPE

This parameter specifies the Packet Identification Rule(PIR) Name.

OBJECT-TYPE

This parameter specifies which Packet classification rules are enabled. It is a Bit Mask field. Bits are defined as follows Bit0 - Dst MAC rule Enabled. Bit1 - Src MAC rule Enabled. Bit2 - Prity rule Enabled. Bit3 - Vlan ID rule Enabled. Bit4 - Ether value rule Enabled. Bit5 - ToS rule Enabled. Bit6 - IP PROTOCOL rule Enabled. Bit7 - Dst IP Addr rule Enabled. Bit8 - Src IP Addr rule Enabled. Bit9 - Dst Port rule Enabled. Bit10 - Src Port rule Enabled. Bit11 - PPPoE Encapsulation rule Enabled.

OBJECT-TYPE

This Parameter specifies the lower limit for the ToS (Types Of Service) classification.

OBJECT-TYPE

This Parameter specifies the higher limit for the ToS classification.

OBJECT-TYPE

This Parameter specifies The ToS Mask which will be used to perform bitwise and operation with incoming Packet's ToS values and it will be checked again Lower & Hight limit the ToS Low, ToS High configuraiton.

OBJECT-TYPE

This Parameter specifies the Protocol Classification for the incoming packet.

OBJECT-TYPE

This parameter specifies the lower limit for the 802.1p classificaiton for the incoming packet.

OBJECT-TYPE

This parameter specifies the Higher limit for the 802.1p classificaiton for the incoming packet.

OBJECT-TYPE

This parameter specifies the VLAN classification for the incoming packet.

OBJECT-TYPE

This parameter specifies the Ether type classification for the incoming ethernet frame.

OBJECT-TYPE

This parameter specifies the Ether Value classificaiton for the incoming ethernet frame.

OBJECT-TYPE

This parameter specifies the PPPoE (Point-to-point Protocol Over Ethernet) Encapsulation status for the incoming ethernet frame.

OBJECT-TYPE

This parameter specifies the protocol id inside the PPPoE Encapsulation data for the incoming ethernet frame.

OBJECT-TYPE

This parameter specifies the index of the worpQoSPIRMapTable.

OBJECT-TYPE

This parameter is used to configure the worpQoSPIRTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This Table holds the Service Flow Classification (SFC) information for QoS feature.

OBJECT-TYPE

This parameter represents the entry for the worpQoSSFClassTable.

OBJECT-TYPE

This parameter specifies the index number of the entry in the worpQoSSFClassTable.

OBJECT-TYPE

This parameter specifies the Service Flow Class Name.

OBJECT-TYPE

This parameter specifies the type of Scheduler to be used for this Service Flow. Select 1 for rtps - Real Time Polling Service 2 for be - Best Effort.

OBJECT-TYPE

This parameter specifies the Direction of the Service Flow.

OBJECT-TYPE

This parameter specifies the Status of the Service Flow.

OBJECT-TYPE

This parameter specifies the Maximum Information Rate(MIR) for this Service Flow. This value is represented in Kbps.

OBJECT-TYPE

This parameter specifies the Comitted Information Rate(CIR) for this Service Flow. This value is represented in Kbps.

OBJECT-TYPE

This parameter specifies the Latency for this Service Flow. This is represented in milliseconds.

OBJECT-TYPE

This parameter specifies the Jitter for this Service Flow. This is represented in milliseconds.

OBJECT-TYPE

This parameter specifies the priority of execution of the Service Flow inside a QoS Class.

OBJECT-TYPE

This parameter specifies the Number of maximum messages can be sent in a single burst.

OBJECT-TYPE

This parameter is used to configure the worpQoSSFClassTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This Table holds the Class information for QoS feature.

OBJECT-TYPE

This parameter represents the entry for the worpQoSClassTable.

OBJECT-TYPE

This parameter specifies the QoS Class index.

OBJECT-TYPE

This parameter specifies the SFC index within the QoS Class index.

OBJECT-TYPE

This parameter specifies the PIR index within the QoS SFC index.

OBJECT-TYPE

This parameter specifies the reference index of the QoS SFC Table index.

OBJECT-TYPE

This parameter specifies the reference index of the QoS PIR Table index.

OBJECT-TYPE

This parameter specifies the QoS Class Name.

OBJECT-TYPE

This parameter specifies the PIR Execution priority within a QoS Class

OBJECT-TYPE

This parameter is used to configure the worpQoSClassTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This Table holds the SU/End Point B entries for QoS feature.

OBJECT-TYPE

This parameter represents the entry for the worpQoSSUTable.

OBJECT-TYPE

This parameter specifies the index number of the entry in the table

OBJECT-TYPE

This parameter specifies the wireless MAC Address of the SU or End Point B

OBJECT-TYPE

This parameter specifies the reference index of the QoS Class Table index.

OBJECT-TYPE

This parameter specifies the comment for this entry.

OBJECT-TYPE

This parameter is used to configure the worpQoSSUTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This parameter specifies the QoS Class need to be used by the SU/End Point B connected to BSU/End Point A but not listed in the worpQoSSUTable.

OBJECT-TYPE

This parameter specifies the QoS Class need to be used for the Layer 2 Broadcast traffic on the Downlink direction.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure the network IP parameters.

OBJECT-TYPE

This table represents the entry for the network IP configuration table

OBJECT-TYPE

This parameter represents the index for the network IP configuration table and interface number.

OBJECT-TYPE

This parameter is used to configure the IP Address for the ethernet interface.

OBJECT-TYPE

This parameter is used to configure the subnet mask for the ethernet interface.

OBJECT-TYPE

This parameter is used to set the IP address of the gateway or router of the device. This parameter is deprecated and please use the object netCfgAllIntfDefaultRouterIpAddr to set the gateway IP address.

OBJECT-TYPE

This parameter is used to specify whether the device network paramenters are to be configured through a dhcp client or to be assigned statically. If the value is set to 1, then the device is configured as static. If the value is set to 2, then the device is set to dynamic.

OBJECT-TYPE

This table is used to configure the wireless network IP parameters in routing mode.

OBJECT-TYPE

This table represents the entry for the network IP configuration table

OBJECT-TYPE

This parameter is user defined index or interface number in the network IP wireless configuration table.

OBJECT-TYPE

This parameter is used to configure the IP Address for the wireless interface.

OBJECT-TYPE

This parameter is used to configure the subnet mask for the wireless interface.

OBJECT-TYPE

This table is used to configure the static routes in routing mode.

OBJECT-TYPE

This parameter represents the entry status for the netIpStaticRouteTable and this table holds upto 256 entries.

OBJECT-TYPE

This parameter represents the index of the netIpStaticRouteTable.

OBJECT-TYPE

This parameter is used to enter the destination IP address for which the static route is to be made.

OBJECT-TYPE

This parameter is used to enter the mask for the destination address.

OBJECT-TYPE

This parameter represents the next reachable hop using which route is made to the destination IP address.

OBJECT-TYPE

This parameter represents the Metric, i.e.,the 'distance' to the target (usually counted in hops).

OBJECT-TYPE

This parameter is used to configure the netIpStaticRouteTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to clear the wired/wireless interface statistics.

OBJECT-TYPE

Default Router Address that applies to all interfaces.

OBJECT-TYPE

This parameter shows the names of supported interfaces depending on the network mode.

OBJECT-TYPE

This parameter is used to enable/disable the static routes option.

OBJECT-TYPE

This parameter is used to monitor the wireless interface for every specified number of minutes. The value 0 disables monitoring.

OBJECT-TYPE

This parameter is used to monitor the ethernet interface for every specified number of minutes. The value 0 disables monitoring.

OBJECT-TYPE

This parameter is to configure the Primary DNS IP Address to be used by this product.

OBJECT-TYPE

This parameter is to configure the Secondary DNS IP Address to be used by this product.

OBJECT-TYPE

This parameter is used to monitor the wireless interface for every specified number of seconds. The value 0 disables monitoring. It can be configured from 5 to 600 seconds.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to configure the NAT(Network Address Translation) status.

OBJECT-TYPE

This parameter is used to enable or disable static bind entries on the NAT device.

OBJECT-TYPE

This table is used to configure NAT Port bind specific information.

OBJECT-TYPE

This parameter represents an entry in the NAT Static Port Bind Table.

OBJECT-TYPE

This parameter is used as the index for the NAT static Port bind table.

OBJECT-TYPE

This parameter represents the local IP address for this NAT Static Port bind Table entry.

OBJECT-TYPE

This parameter represents the port type for this NAT Static Port bind Table entry.

OBJECT-TYPE

This parameter represents the start port number for this NAT Static Port bind Table entry.

OBJECT-TYPE

This parameter represents the end port number for this NAT Static Port bind Table entry.

OBJECT-TYPE

This parameter is used to configure the natStaticPortBindTable status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to configure the RIP configuration status.

OBJECT-TYPE

This table is used to configure the RIP configuration information.

OBJECT-TYPE

This parameter represents the entry for the ripConfigTable.

OBJECT-TYPE

This parameter represents the index for ripConfigTable.

OBJECT-TYPE

This parameter shows the available interfaces for which the rip can be configured.

OBJECT-TYPE

This parameter is used to enable/disable the rip for the particular interface.

OBJECT-TYPE

This parameter represents the authentication type used for rip configuration.

OBJECT-TYPE

This parameter is used to configure the authentication key for the authentication type.

OBJECT-TYPE

This parameters allows to configure the rip version verion.

OBJECT-TYPE

This parameter allows to configure the interface to receive only RIP version 1 and/or RIP verison 2 packets.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to configure the VLAN functionality. Select 1 to enable the VLAN functionality and 2 to disable the VLAN functionality.

OBJECT-TYPE

This parameter represents the management VLAN Identifier (ID).

OBJECT-TYPE

This parameter represents the management VLAN priority, giving eight (2^3) priority levels with the highest priority as seven.

OBJECT-TYPE

This table is used to configure the VLAN parameters for the ethernet interface.

OBJECT-TYPE

This parameter represents the entry for the Vlan Configuration table.

OBJECT-TYPE

This parameter represents the physical interface and used as index to this table.

OBJECT-TYPE

This parameter is used to set the VLAN Mode for the physical interface.

OBJECT-TYPE

This parameter is used to set the access VlanId for the physical interface.

OBJECT-TYPE

This parameter is used to set the access Vlan priority, which varies from 0 to 7 with 7 having highest priority.

OBJECT-TYPE

This parameter is used to set the option to allow the untagged frames.

OBJECT-TYPE

This table is used to configure the VLAN trunk parameters for ethernet interface.

OBJECT-TYPE

This parameter represents the entry for the Vlan Trunk Configuration table.

OBJECT-TYPE

This parameter represents the vlan trunk table index and also represents the ethernet interface.

OBJECT-TYPE

This parameter represents the trunk table secondary index.

OBJECT-TYPE

This parameter is used to set the trunk id.

OBJECT-TYPE

This parameter is used to configure the vlan trunk table status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This parameter stores the information whether the Global Filterng is Enabled or Disabled. If this parameter is set to enabled, then the filtering is enabled. If this parameter is disabled, then filtering will be disabled. Select 1 to enable this parameter and 2 to disable this parameter.

OBJECT-TYPE

This parameter controls the wireless to wireless communication. If this parameter is set to enabled, then wireless to wireless communication is not allowed. If this parameter is set disabled, then wireless to wireless communication is allowed. Select 1 to enable the wireless to wireless communication and 2 to disable wireless to wireless communication.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to configure the interface. By default, the parameter is set to disabled. The filter can be enabled either for Ethernet, Wireless or All Interface. Select 1 for ethernet, 2 for wireless, 3 for all interfaces and 4 for disable.

OBJECT-TYPE

If the specific protocol is not available in the ethernet protocol table, then this parameter specifies the action that needs to be taken on the packet. If this parameter is set to passthru (1), then specific protocol will be allowed. If this parameter is set to block (2), then specific protocol will be denied.

OBJECT-TYPE

This table contains the two byte hexadecimal values of the protocols. The packets whose protocol field matches with any of the entries in this table will be forwarded or dropped.

OBJECT-TYPE

This parameter represents an entry in the protocol filter table. This table supports upto 64 entries.

OBJECT-TYPE

This parameter represents the index of the ethernet protocol Filtering table.

OBJECT-TYPE

This parameter represents a two byte hexadecimal value for the Ethernet protocol to be filtered.

OBJECT-TYPE

This parameter represents the value in the protocol field of the Ethernet packet. The value is of 4-digit Hex format. Example: The value of IP protocol is 0800. The value of ARP protocol is 0806.

OBJECT-TYPE

This parameter is used to configure the status of the ethernet protocol filtering. Select 1 to block, 2 to passthru.

OBJECT-TYPE

This parameter is used to configure the ethernet protocol filtering table status. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This table provides the MAC address of the stations on the wired and the wireless interface; the MAC addresses will be given in pairs. Stations listed in the Static MAC Address filter will have no traffic forwarded by the device. This way Multicast traffic exchanged between stations or servers can be prevented, from being transmitted over the wireless medium when both stations are actually located on the wired backbone.

OBJECT-TYPE

This parameter identifies the entry in the Static MAC address filter table. This table support upto 200 entries.

OBJECT-TYPE

This parameter is user defined that represents the index of the Static MAC Filtering table.

OBJECT-TYPE

This parameter represents the MAC address of the station on the wired interface of the device.

OBJECT-TYPE

This parameter represents the MAC address of the filter wired MASK.

OBJECT-TYPE

This parameter represents the MAC address for the wireless interface.

OBJECT-TYPE

This parameter represents the mask for the wireless interface MAC address.

OBJECT-TYPE

This parameter is used for an optional comment associated to the staticMACAddrFilter entry.

OBJECT-TYPE

This parameter is used to configure the status of the staticMACAddrFilterTable. Select It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure the advanced filtering using protocol name and direction.

OBJECT-TYPE

This parameter represents the entry for advancedFilterTable. This table supports up to 5 entries.

OBJECT-TYPE

This parameter represents the index of the advanced filtering table.

OBJECT-TYPE

This parameter represents the protocol name to be filtered. (DenyIPX RIP, Deny IPX SAP, Deny IPX LSP, Deny IP Broadcasts, Deny IP Multicasts)

OBJECT-TYPE

This parameter represents the direction of the individual entry in the advanced filter table. The direction can be enabled either for Ethernet to Wireless, Wireless to Ethernet or both. Select 1 for ethernet2wireless, 2 for wireless2ethernet, 3 for both.

OBJECT-TYPE

This parameter is used to configure the row status of the advanced filtering table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to configure the Tcp Udp Port Filtering. Select 1 to enable and 2 to disable the Tcp Udp Port Filtering.

OBJECT-TYPE

This table contains the configurations for the Tcp Udp Port Filtering table.

OBJECT-TYPE

This parameter represents the entry for tcpudpPortFilterTable. This table supports up to 64 entries.

OBJECT-TYPE

This parameter is used as index for the TcpUdp port filter table.

OBJECT-TYPE

This parameter represents the protocol name for the tcpudpPortFilter.

OBJECT-TYPE

This parameter represents the Port number for the tcpudpPortFilter.

OBJECT-TYPE

This parameter represents the port type for this TcpUdp Port filter table. The parameter can be either TCP or UDP or TCP/UDP. Select 1 for TCP, 2 for UDP and 3 for both.

OBJECT-TYPE

This parameter is used to configure the interface. By default, the parameter is set to All Interfaces. The filter can be enabled either for Ethernet, Wireless or All Interface. Select 1 for only Ethernet, 2 for only Wireless and 3 for allInterfaces.

OBJECT-TYPE

The parameter indicates the status of the TCP/UDP portfilter table entry. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6)

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to enable/disable IntraCell Blocking/Filtering.

OBJECT-TYPE

The MAC table entries for IntraCell Blocking filters. This table can hold up to a maximum of 250 entries.

OBJECT-TYPE

This parameter represents the entry in the IntraCell Blocking MAC Table.

OBJECT-TYPE

This parameter is used as the index to the IntraCell Blocking MAC Table.

OBJECT-TYPE

This parameter represents the MAC address of the SU which is allowed to communicate with other SUs with the same group ID.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter enables to segregate the SUs for intra/ inter cell communications.

OBJECT-TYPE

This parameter is used to configure the row status for the worp Intra cell blocking MAC table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This table holds the group entries for IntraCell Blocking.

OBJECT-TYPE

This parameter represents the entry in the IntraCell Blocking Group Table. This table can contain a maximum of 16 entries.

OBJECT-TYPE

This parameter is used as the index to the IntraCell Blocking Group Table.

OBJECT-TYPE

This parameter represents the group name.

OBJECT-TYPE

This parameter is used to enable, disable the IntraCell Blocking Group Table.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to enable or disable security gateway feature.

OBJECT-TYPE

This parameter represents the security Gateway MAC Address to which all frames will be forwarded by the device.

OBJECT-TYPE

STP Frame forward status will block/allow the IEEE 802.1D and 802.1Q reserved MAC addresses (01:80:C2:00:00:00 to 01:80:C2:00:00:0F) Select 1 to enable this parameter and 2 to disable this parameter.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains information on the threshold value of the multicast and brodcast packects that can be processed for interface(s) present in the device .

OBJECT-TYPE

This parameter represents the entry in the storm threshold table.

OBJECT-TYPE

This parameter is used as index for the storm Threshold Table.

OBJECT-TYPE

This parameter is used to configure the interface.The filter can be enabled either for Ethernet or Wireless. 1 for Ethernet 2 for Wireless

OBJECT-TYPE

This parameter is used to provide the threshold value of the multicast packets to be processed for the interface. If threshold value for multicast packets is set to '0', no filtering will take place (filtering will be disabled).Excess packets will be dropped if packets are more than threshold value.To disable MultiCast packets filtering for this interface this variable should be set to '0'(zero).

OBJECT-TYPE

This parameter is used to provide the threshold value of the broadcast packets to be processed for interface.If threshold value for broadcast packets is set to '0', no filtering will take place (filtering will be disabled). Excess packets will be dropped if packets are more than threshold value.To disable Broadcast wireless packets filtering,this variable should be set to '0' (Zero).

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This parameter indicates if the DHCP server/relay is enabled or disabled in the device.

OBJECT-TYPE

This parameter represents the maximum lease time in 100th seconds for the IP address assigned by the DHCP server to the DHCP client.

OBJECT-TYPE

This table is used to configure the DHCP server for a particular interface.

OBJECT-TYPE

This parameter represents the entry for the dhcpServerIfTable.

OBJECT-TYPE

This parameter represents the index for the dhcpServerIfTable.

OBJECT-TYPE

This parameter shows the list of interfaces for which the DHCP can be configured.

OBJECT-TYPE

This parameter is used to configure the mask for the interface shown.

OBJECT-TYPE

This parameter represents the IP Address of the gateway or router that the DHCP Server will assign to the DHCP client.

OBJECT-TYPE

This parameter represents the primary DNS Server IP Address to be assinged to a DHCP Client.

OBJECT-TYPE

This parameter represents the secondary DNS Server IP Address to be assinged to a DHCP Client.

OBJECT-TYPE

This parameter represents the default lease time, in 100th seconds, for the IP address assigned by the DHCP server to the DHCP client.

OBJECT-TYPE

This parameter represents an optional comment for this table entry.

OBJECT-TYPE

This parameter is used to configure the row status for the dhcpServerIfTable. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This table contains the pools of IP Addresses that the DHCP server will assign to the DHCP clients.

OBJECT-TYPE

This parameter represents entries in the dhcpServerIpPoolTable.

OBJECT-TYPE

This parameter is used as the index for the IP Address Pool table.

OBJECT-TYPE

This parameter shows the list of interfaces for which the DHCP server can be configured.

OBJECT-TYPE

This parameter represents the start IP address for this DHCP IP Address IP Pool Table entry.

OBJECT-TYPE

This parameter represents the end IP address for this DHCP IP Address IP Pool Table entry.

OBJECT-TYPE

This parameter is used to configure the row status for the dhcpServerIpPoolTable. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This table contains a list of DHCP servers to which the DHCP Agent will communicate with.

OBJECT-TYPE

This parameter represents and entry in the DHCP Server table.

OBJECT-TYPE

This parameter is used as the index to this dhcpRelayServerTable.

OBJECT-TYPE

This parameter represents the IP address of the DHCP server that shall receive DHCP requests from the device.

OBJECT-TYPE

This parameter is used to configure the row status for the dhcpRelayServerTable. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This table holds the information about the supported and current modes of the device.

OBJECT-TYPE

This parameter represents the entry status for the sysTypeTable. It can hold one entry.

OBJECT-TYPE

This parameter represents the physical interface (radio) and index for the sysType Table.

OBJECT-TYPE

This parameter is used to configure the mode of the radio(s). Please refer the sysTypeSupportedMode object for the supported modes. The modes are represented in numbers as follows: AP (1), CLIENT (2), WDS (3), BSU (4), *Applies in TMP(tsunamiMP) mode - please refer sysFeatureProductFamily* EndPointA (4), *Applies in QB(tsunamiQuickBridge) mode - please refer sysFeatureProductFamily* SU (5) *Applies in TMP(tsunamiMP) mode - please refer sysFeatureProductFamily* EndPointB (5) *Applies in QB(tsunamiQuickBridge) mode - please refer sysFeatureProductFamily*

OBJECT-TYPE

This parameter shows the active mode of the radio(s). The configured mode will take effect after the reboot. The modes are represented in numbers as follows: AP (1), CLIENT (2), WDS (3), BSU (4), *Applies in TMP(tsunamiMP) mode - please refer sysFeatureProductFamily* EndPointA (4), *Applies in QB(tsunamiQuickBridge) mode - please refer sysFeatureProductFamily* SU (5) *Applies in TMP(tsunamiMP) mode - please refer sysFeatureProductFamily* EndPointB (5) *Applies in QB(tsunamiQuickBridge) mode - please refer sysFeatureProductFamily*

OBJECT-TYPE

This parameter displays the supported modes of operations complying with the license.

OBJECT-TYPE

This parameter displays the supported frequency domains.

OBJECT-TYPE

This parameter is used to configure the frequency domain. The following list shows in detail: - United States All: 5.3 + 5.4 with DFS and 5.8 without DFS - United States Adhoc: 5.8 without DFS only - United States 2.4 GHz - World All - World 4.9 GHz (4.940 – 4.990 GHz) - World 2.4 GHz (2.400 – 2.472 GHz) - World 2.3 GHz - World 2.5 GHz - Canada 5 GHz (5.250 – 5.350 & 5.470 – 5.600 & 5.650 – 5.725 GHz all bands with DFS) - Europe 5.8 GHz (5.725 – 5.850 GHz with DFS) - Europe 5.4 GHz (5.470 – 5.600 & 5.650 – 5.725 GHz both with DFS) - Europe 2.4 GHz (2.400 – 2.4825 GHz) - Russia 5 GHz (5.150 – 6.080 GHz without DFS) - Taiwan 5 GHz (5.500 – 5.700 with DFS & 5.725 – 5.825 GHz without DFS) - United State 5 GHz (5.250 – 5.350 & 5.470 – 5.725 GHz with DFS & 5.725 – 5.850 GHz without DFS) - Canada 5.8 GHz. - Russia Frequency Convertor. - Japan 2.4 GHz (2412 - 2472 MHz) - Japan 4.9 GHz (4920 - 4980 MHz and 5040 - 5080 MHz). - UK 5.8 GHz (5725 - 5795 MHz and 5825 - 5850 MHz) - World 5.9GHz - United States 5.3 and 5.8 GHz - India 5.8GHz.

OBJECT-TYPE

This parameter shows the active frequency domain. The following list shows in detail: - United States All: 5.3 + 5.4 with DFS and 5.8 without DFS - United States Adhoc: 5.8 without DFS only - United States 2.4 GHz - World All - World 4.9 GHz (4.940 – 4.990 GHz) - World 2.4 GHz (2.400 – 2.472 GHz) - World 2.3 GHz - World 2.5 GHz - Canada 5 GHz (5.250 – 5.350 & 5.470 – 5.600 & 5.650 – 5.725 GHz all bands with DFS) - Europe 5.8 GHz (5.725 – 5.850 GHz with DFS) - Europe 5.4 GHz (5.470 – 5.600 & 5.650 – 5.725 GHz both with DFS) - Europe 2.4 GHz (2.400 – 2.4825 GHz) - Russia 5 GHz (5.150 – 6.080 GHz without DFS) - Taiwan 5 GHz (5.500 – 5.700 with DFS & 5.725 – 5.825 GHz without DFS) - United State 5 GHz (5.250 – 5.350 & 5.470 – 5.725 GHz with DFS & 5.725 – 5.850 GHz without DFS) - Canada 5.8 GHz. - Russia Frequency Convertor - Japan 2.4 GHz (2412 - 2472 MHz) - Japan 4.9 GHz (4920 - 4980 MHz and 5040 - 5080 MHz). - UK 5.8 GHz (5725 - 5795 MHz and 5825 - 5850 MHz) - World 5.9GHz - United States 5.3 and 5.8 GHz - India 5.8GHz.

OBJECT-TYPE

This parameter is used to configure the network mode of the device.

OBJECT-TYPE

This parameter is shows the network mode of the device. This can be configured in the sysNetworkMode.

OBJECT-TYPE

This attribute identifies the country in which the station is operating to set the frequency band. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. This object is not supported for the current products, please refer sysTypeFreqDomain for configuring the Frequency band. Below is the list of mapping of country codes to country names. A5 - ALL5GHz AL - ALBANIA DZ - ALGERIA AR - ARGENTINA AM - ARMENIA AU - AUSTRALIA AT - AUSTRIA AZ - AZERBAIJAN BH - BAHRAIN BY - BELARUS BE - BELGIUM BZ - BELIZE BO - BOLIVIA BR - BRAZIL BN - BRUNEI DARUSSALAM BG - BULGARIA CA - CANADA CL - CHILE CN - CHINA CO - COLOMBIA CR - COSTA RICA HR - CROATIA CY - CYPRUS CZ - CZECH REPUBLIC DK - DENMARK DO - DOMINICAN REPUBLIC EC - ECUADOR EG - EGYPT EE - ESTONIA EU - EUROPEAN UNION FI - FINLAND FR - FRANCE GE - GEORGIA DE - GERMANY GR - GREECE GT - GUATEMALA HK - HONG KONG HU - HUNGARY IS - ICELAND IN - INDIA ID - INDONESIA IR - IRAN IE - IRELAND I1 - IRELAND - 5.8GHz IL - ISRAEL IT - ITALY JP - JAPAN J2 - JAPAN2 JM - JAMAICA JO - JORDAN KZ - KAZAKHSTAN KP - NORTH KOREA KR - KOREA REPUBLIC K2 - KOREA REPUBLIC2 KW - KUWAIT LV - LATVIA LB - LEBANON LI - LIECHTENSTEIN LT - LITHUANIA LU - LUXEMBOURG MO - MACAU MK - MACEDONIA MT - MALTA MY - MALAYSIA MX - MEXICO MC - MONACO MA - MOROCCO NL - NETHERLANDS NZ - NEW ZEALAND NO - NORWAY OM - OMAN PK - PAKISTAN PA - PANAMA PE - PERU PH - PHILIPPINES PL - POLAND PT - PORTUGAL PR - PUERTO RICO QA - QATAR RO - ROMANIA RU - RUSSIA SA - SAUDI ARABIA CS - SERBIA & MONTENEGRO SG - SINGAPORE SK - SLOVAK REPUBLIC SI - SLOVENIA ZA - SOUTH AFRICA ES - SPAIN SE - SWEDEN CH - SWITZERLAND SY - SYRIA TW - TAIWAN TH - THAILAND TR - TURKEY UA - UKRAINE AE - UNITED ARAB EMIRATES GB - UNITED KINGDOM G1 - UNITED KINGDOM - 5.8GHz US - UNITED STATES UW - UNITED STATES - World U1 - UNITED STATES - DFS UY - URUGUAY VE - VENEZUELA VN - VIETNAM

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to enable/disable the IGMP snooping. Only passive snooping is supported. This feature is supported only in bridge mode.

OBJECT-TYPE

This parameter represents the time after which the IGMP multicast group age-outs/elapses.

OBJECT-TYPE

This parameter represents the time after which the IGMP router port age-outs/elapses.

OBJECT-TYPE

If this paramter is set with Yes, all unregistered multicast traffic and membership reports will be flooded to all ports.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This attribute identifies the country in which the station is operating. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. Below is the list of mapping of country codes to country names. This object is deprecated and please use sysConfCountryCode to set the country code. AL - ALBANIA DZ - ALGERIA AR - ARGENTINA AM - ARMENIA AU - AUSTRALIA AT - AUSTRIA AZ - AZERBAIJAN BH - BAHRAIN BY - BELARUS BE - BELGIUM BZ - BELIZE BO - BOLIVIA BR - BRAZIL BN - BRUNEI DARUSSALAM BG - BULGARIA CA - CANADA CL - CHILE CN - CHINA CO - COLOMBIA CR - COSTA RICA HR - CROATIA CY - CYPRUS CZ - CZECH REPUBLIC DK - DENMARK DO - DOMINICAN REPUBLIC EC - ECUADOR EG - EGYPT EE - ESTONIA EU - EUROPEAN UNION FI - FINLAND FR - FRANCE GE - GEORGIA DE - GERMANY GR - GREECE GT - GUATEMALA HK - HONG KONG HU - HUNGARY IS - ICELAND IN - INDIA ID - INDONESIA IR - IRAN IE - IRELAND I1 - IRELAND - 5.8GHz IL - ISRAEL IT - ITALY JP - JAPAN J2 - JAPAN2 JM - JAMAICA JO - JORDAN KZ - KAZAKHSTAN KP - NORTH KOREA KR - KOREA REPUBLIC K2 - KOREA REPUBLIC2 KW - KUWAIT LV - LATVIA LB - LEBANON LI - LIECHTENSTEIN LT - LITHUANIA LU - LUXEMBOURG MO - MACAU MK - MACEDONIA MT - MALTA MY - MALAYSIA MX - MEXICO MC - MONACO MA - MOROCCO NL - NETHERLANDS NZ - NEW ZEALAND NO - NORWAY OM - OMAN PK - PAKISTAN PA - PANAMA PE - PERU PH - PHILIPPINES PL - POLAND PT - PORTUGAL PR - PUERTO RICO QA - QATAR RO - ROMANIA RU - RUSSIA SA - SAUDI ARABIA CS - SERBIA & MONTENEGRO SG - SINGAPORE SK - SLOVAK REPUBLIC SI - SLOVENIA ZA - SOUTH AFRICA ES - SPAIN SE - SWEDEN CH - SWITZERLAND SY - SYRIA TW - TAIWAN TH - THAILAND TR - TURKEY UA - UKRAINE AE - UNITED ARAB EMIRATES GB - UNITED KINGDOM G1 - UNITED KINGDOM - 5.8GHz US - UNITED STATES UW - UNITED STATES - World U1 - UNITED STATES - DFS UY - URUGUAY VE - VENEZUELA VN - VIETNAM

OBJECT-IDENTITY

OBJECT-TYPE

This table holds the system's inventory management component features.

OBJECT-TYPE

This parameter represents the entry for the sysInvmgmtComponentTable

OBJECT-TYPE

This parameter represents the index for sysInvMgmtCompTable.

OBJECT-TYPE

This parameter identifies the system component serial number

OBJECT-TYPE

This parameter identifies the system component name.

OBJECT-TYPE

This parameter shows the identifier for the component.

OBJECT-TYPE

This parameter identifies the system component variant number.

OBJECT-TYPE

This parameter identifies the system component release version number.

OBJECT-TYPE

This parameter identifies the system component major version number.

OBJECT-TYPE

This parameters identifies the system component minor version number.

OBJECT-TYPE

This parameter represents the system's Security ID.

OBJECT-TYPE

This parameter shows the availability of the daughter card.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to represent the control ID for the system feature.

OBJECT-TYPE

This parameter shows the number of radios supported. This is based on the license file.

OBJECT-TYPE

This parameter shows the supported frequency bands. This is based on the license file.

OBJECT-TYPE

This parameter represents the outward bandwidth in multiples of 1Mbps. This is based on the license file

OBJECT-TYPE

This parameter represents the inward bandwidth in multiples of 1Mbps. This is based on the license file.

OBJECT-TYPE

This parameter represents the current operational mode of the device. This is based on the license file.

OBJECT-TYPE

This table contains a list of features that the current image supports and indicates if this feature is licensed or not. Each row represents a supported feature. Supported indicates if the current image supports the image while licensed indicates that a license is available to use this feature. Based on the license information in this table, some MIB groups/subgroups/tables are enabled or disabled.

OBJECT-TYPE

This table parameter represents the entry for the sysLicFeatureTable. This table can hold a maximum of 50 entries.

OBJECT-TYPE

This parameter represents the index for the sysLicFeatureTable.

OBJECT-TYPE

This parameter represents the feature type and shows the code of the feature.

OBJECT-TYPE

This parameter represents feature value i.e., enabled or disabled.

OBJECT-TYPE

This parameter represents the cumulative bandwidth of the device. This is based on the license file.

OBJECT-TYPE

This parameter represents the number of ethernet interfaces supported. This is based on the license file.

OBJECT-TYPE

This parameter represents the bit map for the features enabled/disabled. The value for this parameter is interpreted as a bitfield and the respective modules are shown below: BRIDGE_MODE_ONLY = 0, WORP = 1, Intra Cell Blocking = 2, Intra BSS Blocking = 3, VLAN = 4, STATIC_ROUTING = 5, NAT = 6, FILTERING = 7. This is based on the license file.

OBJECT-TYPE

This parameter represents the max number of satellites supported. This is based on the license file.

OBJECT-TYPE

This parameter represents the product family. This is based on the license file.

OBJECT-TYPE

This parameter represents the product class. This is based on the license file.

OBJECT-TYPE

This table holds the license file parameters for the radio(s).

OBJECT-TYPE

This table parameter represents the entry for the sysLicRadioInfoTable.

OBJECT-TYPE

This parameter represents the index for the sysLicRadioInfoTable.

OBJECT-TYPE

This parameter represents the component ID for the radio(s).

OBJECT-TYPE

This parameter represents the variant ID for the radio(s).

OBJECT-TYPE

This parameter represents the Antenna type supported for the radio(s).

OBJECT-TYPE

This parameter represents the Antenna MIMO type for the radio(s).

OBJECT-IDENTITY

OBJECT-TYPE

This parameter represents the number of successful commits that has taken place since the system was rebooted last.

OBJECT-TYPE

This parameter is used to apply the changed configurations to the device. Always this should be SET with value '1'. The values available on GET or the read values are defined as follows: 200 : Commit Successful 201 : Commit Successful and reboot the device. Please check the object sysMgmtCfgErrorMsg for Commit status and other information on errors. P.S: Usual commit operation needs atleast 3 seconds and changes in wireless parameters needs upto 60 seconds time interval before sending the response.

OBJECT-TYPE

This parameter is used to restore the device to last working configuration

OBJECT-TYPE

This parameter displays the latest error message occured in configuration.

OBJECT-TYPE

This parameter is used to reboot device. Select 1 to reboot.

OBJECT-TYPE

This parameter is used to reset the device to factory settings.

OBJECT-TYPE

This parameter is used to load the configurations from the Text Based Configuration File.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to identify the email address of the contact person for a device. The length of the email address should be between 6 to 32

OBJECT-TYPE

This parameter is used to identify the phone number of the contact person for a device.

OBJECT-TYPE

This parameter is used to store the location of the system.

OBJECT-TYPE

This parameter is used to represent Longitude.

OBJECT-TYPE

This parameter is used to represent Latitude.

OBJECT-TYPE

This parameter is used to display the elevation of an access point from a known level.

OBJECT-TYPE

A textual description of the entity. This value should includes the full name and version identification of the system's hardware type, software operating-system, and networking software.

OBJECT-TYPE

An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used for the SNMP password and represents the read-only community name used in the SNMP protocol.It is used for reading objects from the SNMP agent. The password should be treated as write-only and would be returned as asterisks. User is not allowed to set since it is same as mgmtSnmpReadWritePassword

OBJECT-TYPE

This parameter is used to represent the read-write community name used in the SNMP protocol. This parameter is used for reading and writing objects to the SNMP agent. This parameter should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This table holds the objects of the mgmtSnmpAccessTable.

OBJECT-TYPE

This parameter represents the entry for the mgmtSnmpAccessTable.

OBJECT-TYPE

This parameter represents the index for the mgmtSnmpAccessTable and this is not-accessible.

OBJECT-TYPE

This table contains the destination IP address and community password for the trap delivery.

OBJECT-TYPE

This parameter represents the entry for the mgmtSnmpTrapHostTable.

OBJECT-TYPE

This parameter represents the index for SNMP Trap Host table. This table supports upto 5 rows.

OBJECT-TYPE

This parameter is used to represent the IP address of the management station that will receive SNMP traps from the device.

OBJECT-TYPE

This parameter is used to represent the password that is sent with the SNMP trap messages to allow the host to accept or reject the traps. The trap host will accept SNMP traps if the sent password matches the host's password. This parameter returns asterisks on get. This is not allowed to set because it is same as mgmtSnmpReadWritePassword.

OBJECT-TYPE

This parameter represents the comment for the row in the SNMP Trap Host Table.

OBJECT-TYPE

This parameter is used to configure the row status for the SNMP Trap Host table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-TYPE

This parameter is used to configure the SNMP Version. The version v2c provides the security by means of community passwords and the version v3 provides highest security with authentication and encryption.

OBJECT-TYPE

This parameter allows to select the security level for SNMPV3. The level noAuthNoPriv is not supported.

OBJECT-TYPE

This parameter allows to configure the authentication protocol in SNMPV3. Select 2 for MD5 and 3 for SHA.

OBJECT-TYPE

This parameter allows to configure the authentication password for the authentication protocol.

OBJECT-TYPE

This parameter allows to configure the privacy (encryption) protocol in SNMPV3. Select 2 for DES and 3 for AES-128.

OBJECT-TYPE

This parameter allows to configure the privacy (encryption) password for the privacy protocol.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter represents the system access password for the HTTP interface to manage the device via a web browser.This parameter would return the value in asterisks.

OBJECT-TYPE

This parameter is used to configure the port on which HTTP is accessed.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter represents the system access password for the Telnet interface. This parameter would return the value in asterisks.

OBJECT-TYPE

This parameter is used to configure the port on which the Telnet is accessed.

OBJECT-TYPE

This parameter is used to configure the number of telnet sessions. A total of 10 sessions (Telnet + SSH) are available

OBJECT-IDENTITY

OBJECT-TYPE

This parameter represents the IP address of the TFTP server.

OBJECT-TYPE

This parameter represents the filename that is to upload or download from the TFTP server.

OBJECT-TYPE

This parameter informs the device about the type of file that is being uploaded or downloaded. Select (1) if it is config file (2) if it is an image file and (3) if it is an eventlog file. (4) if it is a templog file. (5) if it is a Text Based Config File. (6) if it is a eventlog File.

OBJECT-TYPE

This parameter represents the type of TFTP operation that is to be executed. The upload functionality will transfer the specified file from the device to the TFTP server. The download functionality will transfer the specified file from the TFTP server to the device. The download and reboot functionality will download the file from the TFTP server and then reboots the device. Select (1) to upload the image, (2) to download the image and (3) to Download & Reboot the device. (4) none

OBJECT-TYPE

This parameter represents the TFTP operation status. 1 - Idle, 2 - Download in progress 3 - Download Success 4 - Download Failure 5 - Signature check in progress 6 - Signature check failed 7 - Write on flash is in progress 8 - Write on flash is failed 9 - Upload in progress 10 - Upload success 11 - Upload failed

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to provide additional information on traps.

OBJECT-TYPE

This parameter is used to enable or disable the configuration related traps and this is not allowed to set.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter allows to control all management interface accesses. Select 1 - enable and 2 - disable Alert: Disabling this parameter disables all interfaces. Only serial console can be accessed for device management.

OBJECT-TYPE

This parameter allows to enable or disable the HTTP access. Select 1 - enable and 2 - disable

OBJECT-TYPE

This parameter allows to enable or disable the HTTPS access. Select 1 - enable and 2 - disable

OBJECT-TYPE

This parameter allows to enable or disable the SNMP access. Select 1 - enable and 2 - disable

OBJECT-TYPE

This parameter allows to enable or disable the TELNET access. Select 1 - enable and 2 - disable

OBJECT-TYPE

This parameter allows to enable or disable the SSH access. Select 1 - enable and 2 - disable

OBJECT-TYPE

This parameter allows to enable or disable the Management Access Table. Enabling this parameter allows the traffic from only the IP address specified in the Management Access Table. Select 1 - enable and 2 - disable

OBJECT-TYPE

This table provides the facility to allow the traffic from a particular machine identified by the IP address.

OBJECT-TYPE

This parameter represents the entry for the Management Access Table. It can hold a maximum of 5 entries.

OBJECT-TYPE

This parameter represents the index of the Management Access Table.

OBJECT-TYPE

This parameter holds the IP address of the machine to which traffic need to be allowed.

OBJECT-TYPE

This parameter represents the entry status for the Management Access Table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to configure the port on which SSH is accessed.

OBJECT-TYPE

This parameter is used to set the number of concurrent SSH sessions.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to configure the status for the sysLog. Select 1 to enable the Syslog status and 2 to disable the syslog status.

OBJECT-TYPE

This parameter is used to configure the priority for the syslog. Select 1 for emergency, 2 for alert, 3 for critical, 4 for error, 5 for warning, 6 for notice, 7 for info and 8 for debug.

OBJECT-TYPE

This parameter is used to reset or clear the syslog. Select 1 - to reset or clear 2 - none.

OBJECT-TYPE

This table contains the syslog configurations.

OBJECT-TYPE

This parameter represents the entry for the syslogHostTable.

OBJECT-TYPE

This parameter is used to index the syslogHostTable.

OBJECT-TYPE

This parameter is used to represent the IP address for which syslog messages to be sent.

OBJECT-TYPE

This parameter is used to represents the host port number for which the syslog messages are sent.

OBJECT-TYPE

This parameter displays the comment for the host port of the syslog table.

OBJECT-TYPE

This parameter is used to configue the status of the Syslog host entry table. A maximum of 5 entries can be added to this table. It can be configured as active(enable) -1, notInService(disable) - 2, createAndGo(create row) -4, destroy(delete) - 6

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to configure the priority for the event log table. Select 1 for Emergency, 2 for alert, 3 for critical, 4 for error, 5 for warning, 6 for notice, 7 for info and 8 for debug.

OBJECT-TYPE

This parameter is used to reset/clear the event log table. When this parameter is set, then all enteries in the event log table are deleted/cleared. Select (1) to reset the table.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to enable or disable the SNTP functionality. Select 1 to enable SNTP and 2 to Disable the SNTP functionality.

OBJECT-TYPE

This parameter is used for the primary SNTP server name.

OBJECT-TYPE

This parameter is used for the secondary SNTP server name.

OBJECT-TYPE

This parameter is used to specify the appropriate time zone. dateline(1), samoa(2), hawaii(3), alaska(4), pacific-us(5), mountain-us(6), arizona(7), central-us(8), mexico-city(9), eastern-us(10), indiana(11), atlantic-canada(12), santiago(13), ewfoundland(14), brasilia(15), buenos-aires(16), mid-atlantic(17), azores(18), london(19), western-europe(20), eastern-europe(21), cairo(22), russia-iraq(23), iran(24), arabian(25), afghanistan(26), pakistan(27), india(28), bangladesh(29), burma(30), bangkok(31), australia-wt(32), hong-kong(33), beijing(34), japan-korea(35), australia-ct(36), australia-et(37), central-pacific(38), new-zealand(39), tonga(40), western-samoa(41)

OBJECT-TYPE

This parameter is used to indicate the number of hours to adjust for Daylight Saving Time. plus-two(1), plus-one(2), unchanged(3), minus-one(4), minus-two(5)

OBJECT-TYPE

This parameter displays the current time got from the SNTP server

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table contains wireless stations statistics.

OBJECT-TYPE

This parameter represents the entry for wirelessIfStaStatsTable. This is indexed by interface and VAP numbers.

OBJECT-TYPE

This parameter represents the index for the wirelessIfStaStatsTable.

OBJECT-TYPE

This parameter is user defined represents the index of the stations statistics wireless interface table. This table is limited to 255 entries.

OBJECT-TYPE

This parameter represents the number of the station statistics for wireless interface table. You can configure up to 2 entries.

OBJECT-TYPE

The parameter represents the VAP that can be configured for wireless interface. You can configure up to 4.

OBJECT-TYPE

This parameter represents the MAC address of the station for wireless interface for which the statistics are gathered.

OBJECT-TYPE

This parameter represents the Management frames that are recevied..

OBJECT-TYPE

This parameter represnets the control frames that are recevied.

OBJECT-TYPE

This parameter represents the unicast frames that are recevied.

OBJECT-TYPE

This parameter represents the multicast frames that are recevied.

OBJECT-TYPE

This parameter represents the number of bytes received.

OBJECT-TYPE

This parameter represents the number of beacons received.

OBJECT-TYPE

This parameter represents the number of probe requests recevied.

OBJECT-TYPE

This parameter represents the duplicate frames recevied.

OBJECT-TYPE

This parameter represents the no privacy information recevied.

OBJECT-TYPE

This parameter represents the failed WEP information recevied.

OBJECT-TYPE

This parameter represents the failed deMIC information recevied.

OBJECT-TYPE

This parameter represents the failed decapulation information recevied.

OBJECT-TYPE

This parameter represents the failed defragmentation information recevied.

OBJECT-TYPE

This parameter represents the disassociated frames that are recevied.

OBJECT-TYPE

This parameter represents the deauthenticated frames that are recevied.

OBJECT-TYPE

This parameter represents the decrypt information failed on CRC recevied.

OBJECT-TYPE

This parameter represents the unauthorized port information recevied.

OBJECT-TYPE

This parameter represents the unencrypted information recevied.

OBJECT-TYPE

This parameter represents the data frames that are transmitted.

OBJECT-TYPE

This parameter represents the management frames that are transmitted.

OBJECT-TYPE

This parameter represents the number of unicast frames from the station that are further transmitted either by the bridge/router or by the internal host.

OBJECT-TYPE

This parameter represents the number of multicast frames from the station that are further transmitted either by the bridge/router or by the internal host.

OBJECT-TYPE

This parameter represents the number of bytes from the station that are further transmitted either by the bridge/router or by the internal host.

OBJECT-TYPE

This parameter represents the number of transmitted probe request from the station either by the bridge/router or by internal host.

OBJECT-TYPE

This parameter represents the end of service period.

OBJECT-TYPE

This parameter displays the power save mode.

OBJECT-TYPE

This parameter represents the number of associated frames transmitted.

OBJECT-TYPE

This parameter represents the number of the failed associated frames transmitted.

OBJECT-TYPE

This parameter represents the number of the authentication frames transmitted.

OBJECT-TYPE

This parameter represents the failed authentication frames.

OBJECT-TYPE

This parameter represents the deauthorized frames transmitted.

OBJECT-TYPE

This parameter represents the deauthorized code transmitted.

OBJECT-TYPE

This parameter represents the disassociation information transmitted.

OBJECT-TYPE

This parameter representd the disassociation code transmitted.

OBJECT-TYPE

This parameter represents the frequency on which the station is operating.

OBJECT-TYPE

This parameter represents the present state of the station.

OBJECT-TYPE

This parameter represents the RSSI (received signal strength) of the station.

OBJECT-TYPE

This parameter represents the transmission rate of the station.

OBJECT-TYPE

This parameter represents the authentication alogorithm used for the station.

OBJECT-TYPE

This parameter represents the association ID of the station.

OBJECT-TYPE

This parameter represents the VLAN tag of the station.

OBJECT-TYPE

This parameter represents the association time of the station.

OBJECT-TYPE

This parameter represents the transmission power of the station.

OBJECT-TYPE

This parameter represents the inactivity time of the station.

OBJECT-TYPE

This parameter represents the wireless operating mode of station.

OBJECT-TYPE

This parameter represents the HT (high throughput) capability in 11n mode.

OBJECT-TYPE

This table contains WORP stations statistics.

OBJECT-TYPE

This parameter represents an entry in the WORP Interface Satellite Statistics Table.

OBJECT-TYPE

This parameter represents the table index for Station Stats Table.

OBJECT-TYPE

This parameter represents the MAC address of the satellite for which the statistics are gathered.

OBJECT-TYPE

This parameter identifies the name of the base unit being tested with.

OBJECT-TYPE

The current signal level calculated over all inbound packets. This variable indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current noise level calculated over all inbound packets. This variable indicates the running average of the local noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current remote signal level calculated over the inbound packets send by this station. This variable indicates the running average over all registered stations of the remote signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current average remote noise level calculated over the inbound packets send by this station. This variable indicates the running average over all registered stations of the remote noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The number of requests for service sent (satellite) or received (base).

OBJECT-TYPE

The number of polls with data sent (base) or received (satellite).

OBJECT-TYPE

The number of polls with no data sent (base) or received (satellite).

OBJECT-TYPE

The number of poll replies with data sent (satellite) or received (base). This counter does not include replies with the MoreData flag set (see ReplyMoreData).

OBJECT-TYPE

The number of poll replies with no data sent (satellite) or received (base).

OBJECT-TYPE

The number of data packets sent that were acknowledged and did not need a retransmit.

OBJECT-TYPE

The number of data packets sent that needed retransmition but were finally received succesfully by the remote partner.

OBJECT-TYPE

The number of data packets sent that were (finally) not received succesfully by the remote partner.

OBJECT-TYPE

The number of data packets received that were acknowledged and did not need a retransmit of the remote partner.

OBJECT-TYPE

The number of data packets received that needed retransmition by the remote partner but were finally received succesfully.

OBJECT-TYPE

The number of data packets that were (finally) not received succesfully.

OBJECT-TYPE

The number of times a poll was sent but no reply was received. This parameter only applies to the base.

OBJECT-TYPE

This parameter represents the Transmit Data Rate of the BSU.

OBJECT-TYPE

This parameter represents the Transmit Data Rate of the SU which is registered to this SU.

OBJECT-TYPE

This parameter represents the port number of the bridge for which this station is connected.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

When this parameter indicates the local chain balance status.

OBJECT-TYPE

When this parameter indicates the remote chain balance status.

OBJECT-TYPE

This parameter represents the number of stations connected.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to monitor the statistics of interfaces that run WORP.

OBJECT-TYPE

This parameter represents an entry in the WORP Interface Statistics Table.

OBJECT-TYPE

This parameter represents the radio interface for which the WORP statistics are gathered and index to the wirelessIfWORPStats table.

OBJECT-TYPE

This parameter displays the current signal level calculated over all inbound packets.

OBJECT-TYPE

This parameter displays the current noise level calculated over all inbound packets.

OBJECT-TYPE

This parameter displays the current signal level calculated over the inbound packets received at the peer end.

OBJECT-TYPE

This parameter displays the current noise level calculated over the inbound packets received at the peer end.

OBJECT-TYPE

This parameter displays the number of remote partners. For a satellite, this parameter will always be zero or one.

OBJECT-TYPE

This parameter displays the number of Announcement messages sent (base) or received (satellite) on WORP interface

OBJECT-TYPE

This parameter displays the number of requests for service messages sent (satellite) or received (base).

OBJECT-TYPE

This parameter displays the number of registration request messages sent (satellite) or received (base) on WORP interface.

OBJECT-TYPE

This parameter displays the number of registration reject messages sent (base) or received (satellite) on WORP interface.

OBJECT-TYPE

This parameter displays the number of authentication request messages sent (satellite) or received (base) on WORP interface.

OBJECT-TYPE

This parameter displays the number of authentication confirm messages sent (base) or received (satellite) on WORP interface.

OBJECT-TYPE

This parameter represents the number of times a Registration Attempt has been initiated.

OBJECT-TYPE

This parameter represents the number of registration attempts that is not completed yet.

OBJECT-TYPE

This parameter represents the number of times the registration procedure timed out.

OBJECT-TYPE

This parameter represents the reason for why the last registration was aborted or failed.

OBJECT-TYPE

This parameter represents the number of polls with data messages sent (base) or received (satellite).

OBJECT-TYPE

This parameter represents the number of polls with no data messages sent (base) or received (satellite).

OBJECT-TYPE

This parameter represents the number of poll replies with data messages sent (satellite) or received (base).

OBJECT-TYPE

This parameter represents the number of poll replies with more data messages sent (satellite) or received (base).

OBJECT-TYPE

This parameter represents the number of poll replies with no data messages sent (satellite) or received (base).

OBJECT-TYPE

This parameter represents the number of times a poll messages were sent but no reply was received. The parameter in valid only on BSU.

OBJECT-TYPE

This parameter displays the number of data messages sent and acknowledged by the peer successfully.

OBJECT-TYPE

This parameter displays the number of data messages that are re-transmitted and acknowledged by the peer successfully.

OBJECT-TYPE

This parameter displays the number of data messages that requires re-transmission. These frames are not acknowledged by the peer.

OBJECT-TYPE

This parameter displays the number of data messages received and acknowledged successfully.

OBJECT-TYPE

This parameter displays the number of successfully received re-transmitted data messages.

OBJECT-TYPE

This parameter displays the number of data messages that were not received successfully.

OBJECT-TYPE

This parameter provides information about the total assigned (provisioned) uplink Committed Information Rate(CIR) including all SUs.

OBJECT-TYPE

This parameter provides information about the total assigned (provisioned) downlink Commtied Information Rate(CIR) including all SUs.

OBJECT-TYPE

This parameter provides information about the total assigned (provisioned) uplink Maximum Information Rate(MIR) including all SUs.

OBJECT-TYPE

This parameter provides information about the total assigned (provisioned) downlink Maximum Information Rate(MIR) including all SUs.

OBJECT-TYPE

This parameter provides information about the total active uplink Committed Information Rate(CIR).

OBJECT-TYPE

This parameter provides information about the total active downlink Committed Information Rate(CIR).

OBJECT-TYPE

This parameter provides information about the total active uplink Maximum Information Rate(MIR).

OBJECT-TYPE

This parameter provides information about the total active downlink Maximum Information Rate(MIR).

OBJECT-TYPE

This parameter provides information about the current bandwidth utilization on the uplink direction.

OBJECT-TYPE

This parameter provides information about the current bandwidth utilization on the downlink direction.

OBJECT-IDENTITY

OBJECT-TYPE

This table shows the blacklisted channel information.

OBJECT-TYPE

This parameter represents an entry in the wireless interface blacklisted info table.

OBJECT-TYPE

This parameter is used as index to the wirelessIfBlacklistInfoTable and represents the radio number.

OBJECT-TYPE

This parameter is used as secondary index to the wirelessIfBlacklistInfoTable and represents the channel blacklisted.

OBJECT-TYPE

This parameter shows the blacklisted channel number.

OBJECT-TYPE

This parameter shows the reason for the channel blacklisting.

OBJECT-TYPE

This parameter shows the time since the channel is blacklisted.

OBJECT-IDENTITY

OBJECT-TYPE

This table holds the WORP link test configuration parameters.

OBJECT-TYPE

This parameter represents the WORP link test conf table entry status.

OBJECT-TYPE

This parameter represents the index for the WORP link test conf table.

OBJECT-TYPE

This parameter is used to start/stops WORP link test.

OBJECT-TYPE

This parameter shows the progress of the WORP link test.

OBJECT-TYPE

The value of this parameter determines the time (in seconds) that a link test will continue without any SNMP requests for a Link Test Table entry. When the time expires the Link Test Table is cleared.

OBJECT-TYPE

This table contains the information for the stations currently associated with the access point.

OBJECT-TYPE

This parameter represents the entry in the Remote Link Test table.

OBJECT-TYPE

This parameter represents a unique value for each station. The value for each station must remain constant at least from one explore to the next.

OBJECT-TYPE

This parameter represents a unique value for each station. The value for each station must remain constant at least from one explore to the next.

OBJECT-TYPE

When this parameter is set to 2 the device will initiate a link test sequence with this station.

OBJECT-TYPE

This parameter identifies the name of the station whom which the link test is being performed.

OBJECT-TYPE

This parameter represents the MAC address that will be mapped to the IP Address of the station.

OBJECT-TYPE

This parameter shows the link status of WORP connectivity.

OBJECT-TYPE

The current signal level (in dB) for the link test from this station. This parameter indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current noise level (in dB) for the link test to this station. This parameter indicates the running average of the local noise level.

OBJECT-TYPE

The current signal to noise ratio for the link test to this station.

OBJECT-TYPE

The minimum signal level during the link test to this station.

OBJECT-TYPE

The minimum noise level during the link test to this station.

OBJECT-TYPE

The minimum signal to noise ratio during the link test to this station.

OBJECT-TYPE

The maximum signal level during the link test to this station.

OBJECT-TYPE

The maximum noise level during the link test to this station.

OBJECT-TYPE

The maximum signal to noise ratio during the link test to this station.

OBJECT-TYPE

The current signal level for the link test to the remote station or access point.

OBJECT-TYPE

The current noise level for the link test to the remote station or access point device.

OBJECT-TYPE

The current signal to noise ratio for the link test to the remote station or access point device.

OBJECT-TYPE

The minimum signal level during the link test to the remote station or access point device.

OBJECT-TYPE

The minimum noise level during the link test to the remote station or access point device.

OBJECT-TYPE

The minimum signal to noise ratio during the link test to the remote station or access point device.

OBJECT-TYPE

The maximum signal level during the link test to the remote station or access point device.

OBJECT-TYPE

The maximum noise level during the link test to the remote station or access point device.

OBJECT-TYPE

The maximum signal to noise ratio during the link test to the remote station or access point device.

OBJECT-IDENTITY

OBJECT-TYPE

This table holds the statistics for the wireless interface(s).

OBJECT-TYPE

This parameter represents the entry for the wirelessIfStatsTable.

OBJECT-TYPE

This parameter represents the index for the wirelessIfStatsTable.

OBJECT-TYPE

This parameter shows the number of transmitted packets from the wireless interface.

OBJECT-TYPE

This parameter shows the number of transmitted bytes from the wireless interface.

OBJECT-TYPE

This parameter shows the number of received packets from the wireless interface.

OBJECT-TYPE

This parameter shows the number of received bytes from the wireless interface.

OBJECT-TYPE

This parameter shows the number of packets received with decryption errors on the wireless interface.

OBJECT-TYPE

This parameter shows the number of packets received with CRC errors on the wireless interface

OBJECT-TYPE

This parameter shows the control RSSI for the chain/antenna 0.

OBJECT-TYPE

This parameter shows the control RSSI for the chain/antenna 1.

OBJECT-TYPE

This parameter shows the control RSSI for the chain/antenna 2.

OBJECT-TYPE

This parameter shows the Extension RSSI for the chain/antenna 0.

OBJECT-TYPE

This parameter shows the Extension RSSI for the chain/antenna 1

OBJECT-TYPE

This parameter shows the Extension RSSI for the chain/antenna 2

OBJECT-TYPE

This parameter shows the combined RSSI of the control and extension.

OBJECT-TYPE

This parameter shows the Physical layer errors.

OBJECT-TYPE

This parameter shows the Number of times the radio is re-tuned.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to store RADIUS Authentication Client Statistics for the configured profiles.

OBJECT-TYPE

This parameter represents an entry in the radiusClientAuthStatsTable. Note this table is indexed by VAP and Radius Pri/Sec servers

OBJECT-TYPE

This parameter is user defined parameter and used as an index for Radius client Authorization status.

OBJECT-TYPE

This parameter is secondary index to Radius client Authorisation status, 1 represents the primary server and 2 represents the secondary server.

OBJECT-TYPE

This parameter represents the round trip time for messages exchanged between radius client and authentication server since system startup.

OBJECT-TYPE

This parameter represents the number of RADIUS Access Requests messages transmitted from the client to the server since client startup.

OBJECT-TYPE

This parameter represents the number of RADIUS Access Requests retransmitted by the client to the server since system startup.

OBJECT-TYPE

This parameter indicates the number of RADIUS Access Accept messages received since system startup.

OBJECT-TYPE

This parameter represents the number of RADIUS Access Rejects messages received since system startup.

OBJECT-TYPE

This parameter represents the number of RADIUS Access Challenges messages received since system startup.

OBJECT-TYPE

This parameter represents the total number of RADIUS Access messages received from the authentication server since system startup.

OBJECT-TYPE

This parameter represents the number of malformed RADIUS Access Response messages received since system startup.

OBJECT-TYPE

This parameter represents the number of malformed RADIUS Access Response messages containing invalid authenticators received since system startup.

OBJECT-TYPE

This parameters represents the total number of timeouts for RADIUS Access Request messages since system startup.

OBJECT-TYPE

This parameter represents the number of messages with unknown Radius Message Code since system startup.

OBJECT-TYPE

This parameter represents the number of Radius messages which do not contain any EAP payloads or EAP State machine do not have any valid EAP state data since system startup.

OBJECT-TYPE

This table is used to store RADIUS Accounting Client Statistics for the configured profiles.

OBJECT-TYPE

This parameter represents an entry in the radiusClientAccStatsTable. Note this table is indexed by VAP and Radius Pri/Sec servers.

OBJECT-TYPE

This parameter is used as an index to the RADIUS Accounting Client Statistics Table.

OBJECT-TYPE

This parameter is used as secondary index to the RADIUS Accounting Client Statistics Table, which is used to indicate primary and secondary/backup server statistics, 1 represents the Primary server and 2 represents the Secondary server.

OBJECT-TYPE

This parameter represents the round trip time for messages exchanged between radius client and authentication server since system startup .

OBJECT-TYPE

This parameter represents the number of RADIUS Accounting Requests messages transmitted from the client to the server since client startup.

OBJECT-TYPE

This parameter represents the number of RADIUS Accounting Requests retransmitted by the client to the server since system startup.

OBJECT-TYPE

This parameter indicates the number of RADIUS Accounting Response messages received since system startup.

OBJECT-TYPE

This parameter represents the number of malformed RADIUS Access Response messages received since system startup.

OBJECT-TYPE

This parameter represents the total number of timeouts for RADIUS Accounting Response messages since the system startup.

OBJECT-TYPE

This parameter represents the number of messages with unknown Radius Message Code since system startup.

OBJECT-TYPE

This parameter represents the number of Radius messages which do not contain any EAP payloads or EAP State machine do not have any valid EAP state data since system startup.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table contains the information about all the BSU which all are visible for this SU.

OBJECT-TYPE

This parameter represents the entry in the worpSiteSurvey operation table.

OBJECT-TYPE

This parameter represents the index to the worpSiteSurveyOperationTable.

OBJECT-TYPE

This parameter shows the wireless interface name for which site survey parameters are shown.

OBJECT-TYPE

This parameter is used enable/disable the site survey operation.

OBJECT-TYPE

This table contains the information about all the BSU which all are visible for this SU.

OBJECT-TYPE

This parameter represents the entry in the worpSiteSurvey table.

OBJECT-TYPE

This parameter represents te index to the worpSiteSurveyTable.

OBJECT-TYPE

This parameter represents te index to the worpSiteSurveyTable.

OBJECT-TYPE

This parameter represents the MAC address of the BSU.

OBJECT-TYPE

This parameter represents the name of the BSU.

OBJECT-TYPE

This parameter represents the maximum number of satellites allowed to register with this BSU.

OBJECT-TYPE

This parameter represents the number of satellites currently registered on this BSU.

OBJECT-TYPE

This parameter represents the registration status of this satellite on the BSU.

OBJECT-TYPE

This parameter represents the transmission rate of the SU. This field is not valid if the registration status is Not-Registered

OBJECT-TYPE

This parameter represents the transmission rate of the BSU. This field is not valid if the registration status is Not-Registered

OBJECT-TYPE

This parameter displays the current signal level of the incoming wireless frames from this BSU.

OBJECT-TYPE

This parameter displays the current noise level of the incoming wireless frames from this BSU.

OBJECT-TYPE

This parameter represents the current Local SNR.

OBJECT-TYPE

This parameter displays the current signal level of the incoming wireless frames at BSU. This field is not valid if the registration status is Not-Registered

OBJECT-TYPE

This parameter displays the current noise level of the incoming wireless frames at BSU. This field is not valid if the registration status is Not-Registered.

OBJECT-TYPE

This parameter represents the current SNR at BSU. This field is not valid if the registration status is Not-Registered

OBJECT-TYPE

This parameter represents the channel at which the BSU is operating.

OBJECT-TYPE

This parameter represents the BSU channel bandwidth.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the SU's Bridge port for which BSU is connected.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

This parameter represents the Rx rate of BSU.

OBJECT-TYPE

When this parameter indicates the local chain balance status.

OBJECT-TYPE

When this parameter indicates the remote chain balance status.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used for the internal unit temperature in degrees celsius. The range of the temperature is -30 to 60 degrees celsius.

OBJECT-TYPE

This parameter is used set the high temperature threshold by the user.

OBJECT-TYPE

This parameter is used set the low temperature threshold by the user.

OBJECT-TYPE

This parameter is used for logging interval. The valid values are 1,5,10,15,20,25,30,35,40,45,50,55,and 60.

OBJECT-TYPE

This parameter is used for reset/clear the temperature log.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter shows the present CPU usage.

OBJECT-TYPE

This parameter shows the present RAM usage.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table holds the IGMP multicast IP and MAC address details for the ethernet interface 1

OBJECT-TYPE

This parameter represents the entry for this table.

OBJECT-TYPE

This parameter represents the index for this table.

OBJECT-TYPE

This parameter indicates the IP multicast address of ethernet interface 1 learned by IGMP snooping.

OBJECT-TYPE

This parameter indicates the Mac multicast address of ethernet interface 1 learned by IGMP snooping.

OBJECT-TYPE

This parameter specifies the aging time for multicast entries for the ethernet interface 1.

OBJECT-TYPE

This table holds the IGMP multicast IP and MAC address details for the ethernet interface 2

OBJECT-TYPE

This parameter represents the entry for this table.

OBJECT-TYPE

This parameter represents the index for this table.

OBJECT-TYPE

This parameter indicates the IP multicast address of ethernet interface 2 learned by IGMP snooping.

OBJECT-TYPE

This parameter indicates the Mac multicast address of ethernet interface 2 learned by IGMP snooping.

OBJECT-TYPE

This parameter specifies the aging time for multicast entries for the ethernet interface 2.

OBJECT-IDENTITY

OBJECT-TYPE

This table holds the IGMP multicast IP and MAC address details for the wireless interface 1.

OBJECT-TYPE

This parameter represents the entry for the wireless multicast table.

OBJECT-TYPE

This parameter represents the index for this table.

OBJECT-TYPE

This parameter indicates the IP multicast address of wireless interface 1 learned by IGMP snooping.

OBJECT-TYPE

This parameter indicates the Mac multicast address of wireless interface 1 learned by IGMP snooping.

OBJECT-TYPE

This parameter specifies the aging time for multicast entries for the wireless interface 1.

OBJECT-TYPE

This table shows the IGMP router port stats for all interfaces.

OBJECT-TYPE

This parameter represents the entry for the router port list table.

OBJECT-TYPE

This paramter represents the interface number or index to this table.

OBJECT-TYPE

This parameter represents the router port number on which IGMP snooping/listening is done.

OBJECT-TYPE

This parameter represents the time elapsed since snooping is started on the router port.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter specifies which debug levels are enabled. It is Bit Mask field. Bits are defined as follows Bit0 - WORP general debug level. Bit1 - DDRS debug level one. Bit2 - DDRS debug level two. Bit3 - DDRS debug level three.

OBJECT-TYPE

This parameter is used to reset/clear the debug log messages. When this parameter is set, then all enteries in the event log table are deleted/cleared. Select (1) to reset the table.

OBJECT-TYPE

This parameter represents number line present in the debuglog file.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY