MIBs Depot

PM-MIB

Registered at
1.3.6.1.4.1.10418.17
Last updated
2010-11-24 00:00
Organization
Avocent Corporation
Revisions
2010-11-24 00:00, 2010-09-24 00:00, 2010-04-14 00:00, 2009-05-21 00:00
Namespace
avocent
Source file
PM-MIB
Digest
sha256:ef247a2066101ef76b5a249e78c9573dab4dd99258168573df526cf8c42b279b

Description

This module defines the Avocent MIB extensions to PM-PDU products.

Contact

postal : Avocent Corporation 47281 Bayside Parkway Fremont, CA 94538, USA e-mail : Technical Support techsupport@avocent.com

Imports

FromSymbols
IF-MIBInterfaceIndex, InterfaceIndexOrZero
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIInteger32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

IANAifType-MIB
IF-MIB
PM-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
pmProducts
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1
pm1024
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.1
pm2003
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.2
pm2006
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.3
pm2024
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.4
pm3003
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.5
pm3006
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.6
pm3024
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.7
pm1010
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.8
pm2010
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.9
pm3010
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.10
pm1020
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.11
pm2020
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.12
pm3020
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.1.13
pmManagement
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.2
pmAppliance
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.2.1
pmHostName
OBJECT-TYPE
The appliance name
1.3.6.1.4.1.10418.17.2.1.1DisplayString (SIZE(0..32))read-onlycurrent
pmProductModel
OBJECT-TYPE
The appliance product model
1.3.6.1.4.1.10418.17.2.1.2DisplayString (SIZE(0..50))read-onlycurrent
pmPartNumber
OBJECT-TYPE
The part number of this appliance as shown on the label attached or imprinted on the appliance.
1.3.6.1.4.1.10418.17.2.1.3DisplayString (SIZE(0..32))read-onlycurrent
pmSerialNumber
OBJECT-TYPE
The serial number of this appliance as shown on the label attached or imprinted on the appliance.
1.3.6.1.4.1.10418.17.2.1.4DisplayString (SIZE(0..32))read-onlycurrent
pmEIDNumber
OBJECT-TYPE
The electronic ID number (EID) of this appliance as shown on the label attached or imprinted on the appliance.
1.3.6.1.4.1.10418.17.2.1.5DisplayString (SIZE(0..32))read-onlycurrent
pmBootcodeVersion
OBJECT-TYPE
The version of the bootcode of this appliance.
1.3.6.1.4.1.10418.17.2.1.6DisplayString (SIZE(0..32))read-onlycurrent
pmFirmwareVersion
OBJECT-TYPE
The version of the firmware of this appliance.
1.3.6.1.4.1.10418.17.2.1.7DisplayString (SIZE(0..32))read-onlycurrent
pmReboot
OBJECT-TYPE
A set value of reboot(2) will reboot the appliance. noAction(1) = always returned in a GET. Does nothing if SET. reboot(2) = when SET the appliance immediately reboots.
1.3.6.1.4.1.10418.17.2.1.9INTEGER {noAction(1), reboot(2)}read-writecurrent
pmSessions
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.2.2
pmActiveSessionsNumberOfSession
OBJECT-TYPE
Number of active sessions.
1.3.6.1.4.1.10418.17.2.2.1Integer32read-onlycurrent
pmActiveSessionsTable
OBJECT-TYPE
This table contains the list of active sessions.
1.3.6.1.4.1.10418.17.2.2.2not-accessiblecurrent
pmActiveSessionsTableEntry
OBJECT-TYPE
each entry has the information about the active session
1.3.6.1.4.1.10418.17.2.2.2.1not-accessiblecurrent
pmActiveSessionsTableIndex
OBJECT-TYPE
A unique index representing an entry in this table.
1.3.6.1.4.1.10418.17.2.2.2.1.1InterfaceIndexOrZeroread-onlycurrent
pmActiveSessionsTableUser
OBJECT-TYPE
The name of the user that opens this session.
1.3.6.1.4.1.10418.17.2.2.2.1.2DisplayString (SIZE(0..32))read-onlycurrent
pmActiveSessionsTableGroup
OBJECT-TYPE
The name of the group that the user belongs to.
1.3.6.1.4.1.10418.17.2.2.2.1.3DisplayString (SIZE(0..32))read-onlycurrent
pmActiveSessionsTableType
OBJECT-TYPE
The session type.
1.3.6.1.4.1.10418.17.2.2.2.1.4DisplayString (SIZE(0..32))read-onlycurrent
pmActiveSessionsTableConnection
OBJECT-TYPE
Connection type.
1.3.6.1.4.1.10418.17.2.2.2.1.5DisplayString (SIZE(0..32))read-onlycurrent
pmActiveSessionsTableSessionTime
OBJECT-TYPE
Time of the session
1.3.6.1.4.1.10418.17.2.2.2.1.6DisplayString (SIZE(0..32))read-onlycurrent
pmActiveSessionsTableFrom
OBJECT-TYPE
The source IP address of the session.
1.3.6.1.4.1.10418.17.2.2.2.1.7DisplayString (SIZE(0..32))read-onlycurrent
pmActiveSessionsTableKill
OBJECT-TYPE
A set value of killSession(2) will kill the session. noAction(1) = always returned in a GET. Does nothing if SET. killSession(2)= when SET the appliance immediately kills the session.
1.3.6.1.4.1.10418.17.2.2.2.1.8INTEGER {noAction(1), killSession(2)}read-writecurrent
pmPowerMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.2.5
pmPowerMgmtNumSerialPorts
OBJECT-TYPE
The number of Serial Ports that has PDU connected on the appliance.
1.3.6.1.4.1.10418.17.2.5.1Integer32read-onlycurrent
pmPowerMgmtSerialTable
OBJECT-TYPE
Information about each serial port thas has PDU connect.
1.3.6.1.4.1.10418.17.2.5.2not-accessiblecurrent
pmPowerMgmtSerialTableEntry
OBJECT-TYPE
Information about each serial port thas has PDU connect.
1.3.6.1.4.1.10418.17.2.5.2.1not-accessiblecurrent
pmPowerMgmtSerialTableIndex
OBJECT-TYPE
The index of the register.
1.3.6.1.4.1.10418.17.2.5.2.1.1InterfaceIndexread-onlycurrent
pmPowerMgmtSerialTablePortNumber
OBJECT-TYPE
The number of the serial port when the PDU is connected.
1.3.6.1.4.1.10418.17.2.5.2.1.2Integer32read-onlycurrent
pmPowerMgmtSerialTableDeviceName
OBJECT-TYPE
The device name of this serial port.
1.3.6.1.4.1.10418.17.2.5.2.1.3DisplayStringread-onlycurrent
pmPowerMgmtSerialTableNumberPDUs
OBJECT-TYPE
Total number of units connected in this serial port.
1.3.6.1.4.1.10418.17.2.5.2.1.4Integer32read-onlycurrent
pmPowerMgmtSerialTableBuzzer
OBJECT-TYPE
set/get buzzer(s) on or off for the chain. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.2.1.10Integer32read-writecurrent
pmPowerMgmtSerialTableSyslog
OBJECT-TYPE
set/get syslog on or off for the chain. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.2.1.11Integer32read-writecurrent
pmPowerMgmtSerialTableOverCurrent
OBJECT-TYPE
set/get over current proctection on or off for the chain. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.2.1.12Integer32read-writecurrent
pmPowerMgmtSerialTableCycleInterval
OBJECT-TYPE
set/get cycle interval for the chain in whole seconds. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.2.1.13Integer32read-writecurrent
pmPowerMgmtSerialTablePollRate
OBJECT-TYPE
set/get the poll rate for the chain in whole seconds. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.2.1.14Integer32read-writecurrent
pmPowerMgmtSerialTablePassWord
OBJECT-TYPE
set the global password for admin user
1.3.6.1.4.1.10418.17.2.5.2.1.15DisplayStringread-writecurrent
pmPowerMgmtSerialTableSave
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. save(2) = when SET the save command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.2.1.20INTEGER {noAction(1), save(2)}read-writecurrent
pmPowerMgmtSerialTableRestore
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. restore(2) = when SET the restore command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.2.1.21INTEGER {noAction(1), restore(2)}read-writecurrent
pmPowerMgmtPDUTable
OBJECT-TYPE
This table contains the list of detected PDUs.
1.3.6.1.4.1.10418.17.2.5.3not-accessiblecurrent
pmPowerMgmtPDUTableEntry
OBJECT-TYPE
each entry has the information about the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1not-accessiblecurrent
pmPowerMgmtPDUTablePortNumber
OBJECT-TYPE
Number of serial port when the PDU is connected.
1.3.6.1.4.1.10418.17.2.5.3.1.1InterfaceIndexread-onlycurrent
pmPowerMgmtPDUTablePduIndex
OBJECT-TYPE
A PDU position in the chain.
1.3.6.1.4.1.10418.17.2.5.3.1.2InterfaceIndexOrZeroread-onlycurrent
pmPowerMgmtPDUTablePduId
OBJECT-TYPE
PDU identification.
1.3.6.1.4.1.10418.17.2.5.3.1.3DisplayStringread-writecurrent
pmPowerMgmtPDUTablePortName
OBJECT-TYPE
Name of serial port when the PDU is connected.
1.3.6.1.4.1.10418.17.2.5.3.1.4DisplayStringread-onlycurrent
pmPowerMgmtPDUTableModel
OBJECT-TYPE
Model of the PDU. Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.3.1.5DisplayStringread-onlycurrent
pmPowerMgmtPDUTableVendor
OBJECT-TYPE
Vendor of the PDU. Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.3.1.6DisplayStringread-onlycurrent
pmPowerMgmtPDUTableFirmwareVersion
OBJECT-TYPE
Version of the PDU firmware. Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.3.1.7DisplayStringread-onlycurrent
pmPowerMgmtPDUTableNumberOfOutlets
OBJECT-TYPE
Number of outlets of the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.8Integer32read-onlycurrent
pmPowerMgmtPDUTableCurrentNOS
OBJECT-TYPE
Number of current sensors in the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.9Integer32read-onlyobsolete
pmPowerMgmtPDUTableCurrent1Value
OBJECT-TYPE
Current of the sensor 1 in this PDU unit in AMP. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.). This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentValue, pmPowerMgmtPhasesTableCurrentValue, or pmPowerMgmtOutletsTableCurrentValue
1.3.6.1.4.1.10418.17.2.5.3.1.10Integer32read-onlyobsolete
pmPowerMgmtPDUTableCurrent1Max
OBJECT-TYPE
Maximum current of the sensor 1 in this PDU unit in AMP. When the PDU does not have support for maximum value, the value will be 0. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.) Clear this value, set it with Zero value. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentMax, pmPowerMgmtPhasesTableCurrentMax, or pmPowerMgmtOutletsTableCurrentMax
1.3.6.1.4.1.10418.17.2.5.3.1.11Integer32read-writeobsolete
pmPowerMgmtPDUTableCurrent2Value
OBJECT-TYPE
Current of the sensor 2 in this PDU unit in AMP. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.). This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentValue, pmPowerMgmtPhasesTableCurrentValue, or pmPowerMgmtOutletsTableCurrentValue
1.3.6.1.4.1.10418.17.2.5.3.1.12Integer32read-onlyobsolete
pmPowerMgmtPDUTableCurrent2Max
OBJECT-TYPE
Maximum current of the sensor 2 in this PDU unit in AMP. When the PDU does not have support for maximum value, the value will be 0. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.) Clear this value, set it with Zero value. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentMax, pmPowerMgmtPhasesTableCurrentMax, or pmPowerMgmtOutletsTableCurrentMax
1.3.6.1.4.1.10418.17.2.5.3.1.13Integer32read-writeobsolete
pmPowerMgmtPDUTableCurrent3Value
OBJECT-TYPE
Current of the sensor 3 in this PDU unit in AMP. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.) This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentValue, pmPowerMgmtPhasesTableCurrentValue, or pmPowerMgmtOutletsTableCurrentValue
1.3.6.1.4.1.10418.17.2.5.3.1.14Integer32read-onlyobsolete
pmPowerMgmtPDUTableCurrent3Max
OBJECT-TYPE
Maximum current of the sensor 3 in this PDU unit in AMP. When the PDU does not have support for maximum value, the value will be 0. The value of this object is the actual current in AMP * 10. You need to translate the readed value (Ex. : value is 5, the current is 0.5 AMP.) Clear this value, set it with Zero value. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableCurrentMax, pmPowerMgmtPhasesTableCurrentMax, or pmPowerMgmtOutletsTableCurrentMax
1.3.6.1.4.1.10418.17.2.5.3.1.15Integer32read-writeobsolete
pmPowerMgmtPDUTableTemperatureNOS
OBJECT-TYPE
Number of temperature sensors in the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.16Integer32read-onlyobsolete
pmPowerMgmtPDUTableTemperature1Value
OBJECT-TYPE
Temperature of this PM unit in Celsius degrees. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius).
1.3.6.1.4.1.10418.17.2.5.3.1.17Integer32read-onlyobsolete
pmPowerMgmtPDUTableTemperature1Max
OBJECT-TYPE
Maximum temperature detected in this PM unit in Celsius degrees. The value will be Zero when the PDU does not have support for maximum value. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius). Set with Zero value to clear the max. temperature.
1.3.6.1.4.1.10418.17.2.5.3.1.18Integer32read-writeobsolete
pmPowerMgmtPDUTableTemperature2Value
OBJECT-TYPE
Temperature of this PM unit in Celsius degrees. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius).
1.3.6.1.4.1.10418.17.2.5.3.1.19Integer32read-onlyobsolete
pmPowerMgmtPDUTableTemperature2Max
OBJECT-TYPE
Maximum temperature detected in this PM unit in Celsius degrees. The value will be Zero when the PDU does not have support for maximum value. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius). Set with Zero value to clear the max. temperature.
1.3.6.1.4.1.10418.17.2.5.3.1.20Integer32read-writeobsolete
pmPowerMgmtPDUTableTemperature3Value
OBJECT-TYPE
Temperature of this PM unit in Celsius degrees. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius).
1.3.6.1.4.1.10418.17.2.5.3.1.21Integer32read-onlyobsolete
pmPowerMgmtPDUTableTemperature3Max
OBJECT-TYPE
Maximum temperature detected in this PM unit in Celsius degrees. The value will be Zero when the PDU does not have support for maximum value. The value of this object is the actual temperature in degrees C * 10. You need to translate the readed value (Ex. : value is 240, the temperature is 24 Celsius.) If the temperature measurement is not installed this value will be 0. Valid values are 5 to 999 ( 0.5 to 99.9 Celsius). Set with Zero value to clear the max. temperature.
1.3.6.1.4.1.10418.17.2.5.3.1.22Integer32read-writeobsolete
pmPowerMgmtPDUTableHumidityNOS
OBJECT-TYPE
Number of humidity sensors in the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.23Integer32read-onlyobsolete
pmPowerMgmtPDUTableHumidity1Value
OBJECT-TYPE
Humidity of this PM unit . If the humidity measurement is not installed this value will be 0.
1.3.6.1.4.1.10418.17.2.5.3.1.24Integer32read-onlyobsolete
pmPowerMgmtPDUTableHumidity1Max
OBJECT-TYPE
Maximum humidity detected in this PM unit. If the humidity measurement is not installed or the PDU does not have support for maximum value this value will be 0. Set with Zero value to clear the max. temperature.
1.3.6.1.4.1.10418.17.2.5.3.1.25Integer32read-writeobsolete
pmPowerMgmtPDUTableHumidity2Value
OBJECT-TYPE
Humidity of this PM unit . If the humidity measurement is not installed this value will be 0.
1.3.6.1.4.1.10418.17.2.5.3.1.26Integer32read-onlyobsolete
pmPowerMgmtPDUTableHumidity2Max
OBJECT-TYPE
Maximum humidity detected in this PM unit. If the humidity measurement is not installed or the PDU does not have support for maximum value this value will be 0. Set with Zero value to clear the max. temperature.
1.3.6.1.4.1.10418.17.2.5.3.1.27Integer32read-writeobsolete
pmPowerMgmtPDUTableHumidity3Value
OBJECT-TYPE
Humidity of this PM unit . If the humidity measurement is not installed this value will be 0.
1.3.6.1.4.1.10418.17.2.5.3.1.28Integer32read-onlyobsolete
pmPowerMgmtPDUTableHumidity3Max
OBJECT-TYPE
Maximum humidity detected in this PM unit. If the humidity measurement is not installed or the PDU does not have support for maximum value this value will be 0. Set with Zero value to clear the max. temperature.
1.3.6.1.4.1.10418.17.2.5.3.1.29Integer32read-writeobsolete
pmPowerMgmtPDUTableVoltageNOS
OBJECT-TYPE
Number of voltage sensors in the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.30Integer32read-onlyobsolete
pmPowerMgmtPDUTableVoltage1Value
OBJECT-TYPE
Voltage of this sensor in this PDU unit. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageValue, pmPowerMgmtPhasesTableVoltageValue, or pmPowerMgmtOutletsTableVoltageValue
1.3.6.1.4.1.10418.17.2.5.3.1.31Integer32read-onlyobsolete
pmPowerMgmtPDUTableVoltage1Max
OBJECT-TYPE
Maximum voltage of this sensor in this PDU unit. Set with Zero value to clear the maximum voltage. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageMax, pmPowerMgmtPhasesTableVoltageMax, or pmPowerMgmtOutletsTableVoltageMax
1.3.6.1.4.1.10418.17.2.5.3.1.32Integer32read-writeobsolete
pmPowerMgmtPDUTableVoltage2Value
OBJECT-TYPE
Voltage of this sensor in this PDU unit. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageValue, pmPowerMgmtPhasesTableVoltageValue, or pmPowerMgmtOutletsTableVoltageValue
1.3.6.1.4.1.10418.17.2.5.3.1.33Integer32read-onlyobsolete
pmPowerMgmtPDUTableVoltage2Max
OBJECT-TYPE
Maximum voltage of this sensor in this PDU unit. Set with Zero value to clear the maximum voltage. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageMax, pmPowerMgmtPhasesTableVoltageMax, or pmPowerMgmtOutletsTableVoltageMax
1.3.6.1.4.1.10418.17.2.5.3.1.34Integer32read-writeobsolete
pmPowerMgmtPDUTableVoltage3Value
OBJECT-TYPE
Voltage of this sensor in this PDU unit. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageValue, pmPowerMgmtPhasesTableVoltageValue, or pmPowerMgmtOutletsTableVoltageValue
1.3.6.1.4.1.10418.17.2.5.3.1.35Integer32read-onlyobsolete
pmPowerMgmtPDUTableVoltage3Max
OBJECT-TYPE
Maximum voltage of this sensor in this PDU unit. Set with Zero value to clear the maximum voltage. This OID is obsoleted. The value can be retrieved from pmPowerMgmtPDUTableVoltageMax, pmPowerMgmtPhasesTableVoltageMax, or pmPowerMgmtOutletsTableVoltageMax
1.3.6.1.4.1.10418.17.2.5.3.1.36Integer32read-writeobsolete
pmPowerMgmtPDUTableNumberOfPhases
OBJECT-TYPE
Number of phases of the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.37Integer32read-onlycurrent
pmPowerMgmtPDUTableNumberOfBanks
OBJECT-TYPE
Number of banks in the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.38Integer32read-onlycurrent
pmPowerMgmtPDUTableNumberOfSensors
OBJECT-TYPE
Number of sensors in the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.40Integer32read-onlycurrent
pmPowerMgmtPDUTableFactoryDefault
OBJECT-TYPE
A set value of 2 will set the PDU to factory default settings. noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the factory default command is sent to the PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.41INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPDUTableColdStartDelay
OBJECT-TYPE
PDUs cold start delay in whole seconds (0-60). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.42Integer32read-writecurrent
pmPowerMgmtPDUTableReboot
OBJECT-TYPE
A set value of power*(2) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. reboot(2) = when SET the reboot command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.43INTEGER {noAction(1), reboot(2)}read-writecurrent
pmPowerMgmtPDUTableMaxCurrent
OBJECT-TYPE
Maximum value of current allowed in the PDU (A x 10).
1.3.6.1.4.1.10418.17.2.5.3.1.44Integer32read-onlycurrent
pmPowerMgmtPDUTableAlarm
OBJECT-TYPE
Show the PDU alarm status. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.45INTEGER {normal(1), blow-fuse(2), hw-ocp(3), high-critical(4), high-warning(5), low-warning(6), low-critical(7)}read-onlycurrent
pmPowerMgmtPDUTableCurrentValue
OBJECT-TYPE
Actual value of current in the PDU (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.50Integer32read-onlycurrent
pmPowerMgmtPDUTableCurrentMax
OBJECT-TYPE
Maximum value of current in the PDU (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.51Integer32read-onlycurrent
pmPowerMgmtPDUTableCurrentMin
OBJECT-TYPE
Minimum value of current in the PDU (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.52Integer32read-onlycurrent
pmPowerMgmtPDUTableCurrentAvg
OBJECT-TYPE
Average value of current in the PDU (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.53Integer32read-onlycurrent
pmPowerMgmtPDUTableCurrentReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.54INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPDUTablePowerValue
OBJECT-TYPE
Actual value of power in the PDU (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.60Integer32read-onlycurrent
pmPowerMgmtPDUTablePowerMax
OBJECT-TYPE
Maximum value of power in the PDU (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.61Integer32read-onlycurrent
pmPowerMgmtPDUTablePowerMin
OBJECT-TYPE
Minimum value of power in the PDU (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.62Integer32read-onlycurrent
pmPowerMgmtPDUTablePowerAvg
OBJECT-TYPE
Average value of power in the PDU (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.63Integer32read-onlycurrent
pmPowerMgmtPDUTablePowerReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.64INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPDUTablePowerType
OBJECT-TYPE
Type of power values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.65INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtPDUTableVoltageValue
OBJECT-TYPE
Actual value of voltage in the PDU (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.70Integer32read-onlycurrent
pmPowerMgmtPDUTableVoltageMax
OBJECT-TYPE
Maximum value of voltage in the PDU (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.71Integer32read-onlycurrent
pmPowerMgmtPDUTableVoltageMin
OBJECT-TYPE
Minimum value of voltage in the PDU (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.72Integer32read-onlycurrent
pmPowerMgmtPDUTableVoltageAvg
OBJECT-TYPE
Average value of voltage in the PDU (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.73Integer32read-onlycurrent
pmPowerMgmtPDUTableVoltageReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.74INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPDUTableVoltageType
OBJECT-TYPE
Type of voltage values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.75INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtPDUTablePowerFactorValue
OBJECT-TYPE
Actual value of power factor in the PDU (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.80Integer32read-onlycurrent
pmPowerMgmtPDUTablePowerFactorMax
OBJECT-TYPE
Maximum value of power factor in the PDU (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.81Integer32read-onlycurrent
pmPowerMgmtPDUTablePowerFactorMin
OBJECT-TYPE
Minimum value of power factor in the PDU (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.82Integer32read-onlycurrent
pmPowerMgmtPDUTablePowerFactorAvg
OBJECT-TYPE
Average value of power factor in the PDU (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.83Integer32read-onlycurrent
pmPowerMgmtPDUTablePowerFactorReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.84INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPDUTablePowerFactorType
OBJECT-TYPE
Type of power values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.85INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtPDUTablePowerControl
OBJECT-TYPE
A set value of power*(2-4) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. powerOn(2) = when SET the power On command is sent to PDU. powerOff(3) = when SET the power Off command is sent to PDU. powerCycle(4)=when SET the power cycle command is sent to PDU. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.90INTEGER {noAction(1), powerOn(2), powerOff(3), powerCycle(4)}read-writecurrent
pmPowerMgmtPDUTableResetOCP
OBJECT-TYPE
A set value of power*(2) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.91INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPDUTableCurrentHighCritical
OBJECT-TYPE
outlet high critical (alarm) current threshold (A x 10). Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.100Integer32read-writecurrent
pmPowerMgmtPDUTableCurrentHighWarning
OBJECT-TYPE
outlet high warning current threshold (A x 10). Set fails if value is higher than CurrentHighCritical or lower than CurrentLowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.101Integer32read-writecurrent
pmPowerMgmtPDUTableCurrentLowWarning
OBJECT-TYPE
outlet low warning current threshold (A x 10). Set fails if value is higher than CurrentHighWarning or lower than CurrentLowCritical. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.102Integer32read-writecurrent
pmPowerMgmtPDUTableCurrentLowCritical
OBJECT-TYPE
outlet low critical current threshold (A x 10). Set fails if value is higher than CurrentLowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.103Integer32read-writecurrent
pmPowerMgmtPDUTableEnergyValue
OBJECT-TYPE
pdu energy value (Wh). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.3.1.105Integer32read-onlycurrent
pmPowerMgmtPDUTableEnergyStartTime
OBJECT-TYPE
time at which energy calculation commenced (ISO8601 format). Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.3.1.106DisplayStringread-onlycurrent
pmPowerMgmtPDUTableEnergyReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.3.1.107INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtTotalNumberOfOutlets
OBJECT-TYPE
Number of outlets managed by the appliance.
1.3.6.1.4.1.10418.17.2.5.4Integer32read-onlycurrent
pmPowerMgmtOutletsTable
OBJECT-TYPE
This table contains the information about outlets.
1.3.6.1.4.1.10418.17.2.5.5not-accessiblecurrent
pmPowerMgmtOutletsTableEntry
OBJECT-TYPE
each entry has the information about the outlet.
1.3.6.1.4.1.10418.17.2.5.5.1not-accessiblecurrent
pmPowerMgmtOutletsTablePortNumber
OBJECT-TYPE
Serial Port number.
1.3.6.1.4.1.10418.17.2.5.5.1.1InterfaceIndexread-onlycurrent
pmPowerMgmtOutletsTablePduNumber
OBJECT-TYPE
Index.
1.3.6.1.4.1.10418.17.2.5.5.1.2InterfaceIndexread-onlycurrent
pmPowerMgmtOutletsTableNumber
OBJECT-TYPE
Number of the outlet in the PDU.
1.3.6.1.4.1.10418.17.2.5.5.1.3InterfaceIndexread-onlycurrent
pmPowerMgmtOutletsTableName
OBJECT-TYPE
Name of the outlet.
1.3.6.1.4.1.10418.17.2.5.5.1.4DisplayStringread-writecurrent
pmPowerMgmtOutletsTableStatus
OBJECT-TYPE
Status of the outlet. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.5INTEGER {off(1), on(2), offLocked(3), onLocked(4), offCycle(5), onPendingOff(6), offPendingOn(7), onPendingCycle(8), notSet(9), onFixed(10), offShutdown(11), tripped(12)}read-onlycurrent
pmPowerMgmtOutletsTablePowerControl
OBJECT-TYPE
A set value of power*(2-6) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. powerOn(2) = when SET the power On command is sent to PDU. powerOff(3) = when SET the power Off command is sent to PDU. powerCycle(4)=when SET the power cycle command is sent to PDU. powerLock(5)= when SET the power lock command is sent to PDU. powerUnlock(6)=when SET the power unlock command is sent to PDU. The powerLock and powerUnlock are valid only for Cyclades-PM PDUs
1.3.6.1.4.1.10418.17.2.5.5.1.6INTEGER {noAction(1), powerOn(2), powerOff(3), powerCycle(4), powerLock(5), powerUnlock(6)}read-writecurrent
pmPowerMgmtOutletsTablePortName
OBJECT-TYPE
Serial Port Name where the PDU is connected.
1.3.6.1.4.1.10418.17.2.5.5.1.7DisplayStringread-onlycurrent
pmPowerMgmtOutletsTablePduId
OBJECT-TYPE
PDU identification.
1.3.6.1.4.1.10418.17.2.5.5.1.8DisplayStringread-onlycurrent
pmPowerMgmtOutletsTablePostOnDelay
OBJECT-TYPE
post on delay for the outlet (seconds x 10) Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.9Integer32read-writecurrent
pmPowerMgmtOutletsTablePostOffDelay
OBJECT-TYPE
post off delay for the outlet (seconds x 10) Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.10Integer32read-writecurrent
pmPowerMgmtOutletsTableAlarm
OBJECT-TYPE
Show the outlet alarm status. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.45INTEGER {normal(1), blow-fuse(2), hw-ocp(3), high-critical(4), high-warning(5), low-warning(6), low-critical(7)}read-onlycurrent
pmPowerMgmtOutletsTableCurrentValue
OBJECT-TYPE
Actual value of current in the outlet (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.50Integer32read-onlycurrent
pmPowerMgmtOutletsTableCurrentMax
OBJECT-TYPE
Maximum value of current in the outlet (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.51Integer32read-onlycurrent
pmPowerMgmtOutletsTableCurrentMin
OBJECT-TYPE
Minimum value of current in the outlet (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.52Integer32read-onlycurrent
pmPowerMgmtOutletsTableCurrentAvg
OBJECT-TYPE
Average value of current in the outlet (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.53Integer32read-onlycurrent
pmPowerMgmtOutletsTableCurrentReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.5.1.54INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtOutletsTablePowerValue
OBJECT-TYPE
Actual value of power in the outlet (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.60Integer32read-onlycurrent
pmPowerMgmtOutletsTablePowerMax
OBJECT-TYPE
Maximum value of power in the outlet (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.61Integer32read-onlycurrent
pmPowerMgmtOutletsTablePowerMin
OBJECT-TYPE
Minimum value of power in the outlet (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.62Integer32read-onlycurrent
pmPowerMgmtOutletsTablePowerAvg
OBJECT-TYPE
Average value of power in the outlet (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.63Integer32read-onlycurrent
pmPowerMgmtOutletsTablePowerReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.5.1.64INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtOutletsTablePowerType
OBJECT-TYPE
Type of power values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.65INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtOutletsTableVoltageValue
OBJECT-TYPE
Actual value of voltage in the outlet (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.70Integer32read-onlycurrent
pmPowerMgmtOutletsTableVoltageMax
OBJECT-TYPE
Maximum value of voltage in the outlet (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.71Integer32read-onlycurrent
pmPowerMgmtOutletsTableVoltageMin
OBJECT-TYPE
Minimum value of voltage in the outlet (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.72Integer32read-onlycurrent
pmPowerMgmtOutletsTableVoltageAvg
OBJECT-TYPE
Average value of voltage in the outlet (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.73Integer32read-onlycurrent
pmPowerMgmtOutletsTableVoltageReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.5.1.74INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtOutletsTableVoltageType
OBJECT-TYPE
Type of voltage values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.75INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtOutletsTablePowerFactorValue
OBJECT-TYPE
Actual value of power factor in the outlet (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.80Integer32read-onlycurrent
pmPowerMgmtOutletsTablePowerFactorMax
OBJECT-TYPE
Maximum value of power factor in the outlet (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.81Integer32read-onlycurrent
pmPowerMgmtOutletsTablePowerFactorMin
OBJECT-TYPE
Minimum value of power factor in the outlet (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.82Integer32read-onlycurrent
pmPowerMgmtOutletsTablePowerFactorAvg
OBJECT-TYPE
Average value of power factor in the outlet (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.83Integer32read-onlycurrent
pmPowerMgmtOutletsTablePowerFactorReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.5.1.84INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtOutletsTablePowerFactorType
OBJECT-TYPE
Type of power factor values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.85INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtOutletsTableCurrentHighCritical
OBJECT-TYPE
outlet high critical (alarm) current threshold (A x 10). Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.100Integer32read-writecurrent
pmPowerMgmtOutletsTableCurrentHighWarning
OBJECT-TYPE
outlet high warning current threshold (A x 10). Set fails if value is higher than CurrentHighCritical or lower than CurrentLowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.101Integer32read-writecurrent
pmPowerMgmtOutletsTableCurrentLowWarning
OBJECT-TYPE
outlet low warning current threshold (A x 10). Set fails if value is higher than CurrentHighWarning or lower than CurrentLowCritical. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.102Integer32read-writecurrent
pmPowerMgmtOutletsTableCurrentLowCritical
OBJECT-TYPE
outlet low critical current threshold (A x 10). Set fails if value is higher than CurrentLowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.103Integer32read-writecurrent
pmPowerMgmtOutletsTableEnergyValue
OBJECT-TYPE
outlet energy value (Wh). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.5.1.105Integer32read-onlycurrent
pmPowerMgmtOutletsTableEnergyStartTime
OBJECT-TYPE
time at which energy calculation commenced (ISO8601 format). Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.5.1.106DisplayStringread-onlycurrent
pmPowerMgmtOutletsTableEnergyReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.5.1.107INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtNumberOfOutletGroup
OBJECT-TYPE
Number of configured group of outlets.
1.3.6.1.4.1.10418.17.2.5.6Integer32read-onlycurrent
pmPowerMgmtGroupTable
OBJECT-TYPE
This table contains the information about group of outlets.
1.3.6.1.4.1.10418.17.2.5.7not-accessiblecurrent
pmPowerMgmtGroupTableEntry
OBJECT-TYPE
each entry has the information about group of outlets.
1.3.6.1.4.1.10418.17.2.5.7.1not-accessiblecurrent
pmPowerMgmtGroupTableIndex
OBJECT-TYPE
Index of the group.
1.3.6.1.4.1.10418.17.2.5.7.1.1InterfaceIndexOrZeroread-onlycurrent
pmPowerMgmtGroupTableName
OBJECT-TYPE
Name of the group of outlets.
1.3.6.1.4.1.10418.17.2.5.7.1.2DisplayStringread-onlycurrent
pmPowerMgmtGroupTableStatus
OBJECT-TYPE
Status of the group of outlet.
1.3.6.1.4.1.10418.17.2.5.7.1.3INTEGER {off(1), on(2)}read-onlycurrent
pmPowerMgmtGroupTablePowerControl
OBJECT-TYPE
A set value of power*(2-4) will send command to PDU. noAction(1) = always returned in a GET. Does nothing if SET. powerOn(2) = when SET the power On command is sent to PDU. powerOff(3) = when SET the power Off command is sent to PDU. powerCycle(4)=when SET the power cycle command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.7.1.4INTEGER {noAction(1), powerOn(2), powerOff(3), powerCycle(4)}read-writecurrent
pmPowerMgmtTotalNumberOfPhases
OBJECT-TYPE
Number of phases managed by the appliance.
1.3.6.1.4.1.10418.17.2.5.8Integer32read-onlycurrent
pmPowerMgmtPhasesTable
OBJECT-TYPE
This table contains the information about phases.
1.3.6.1.4.1.10418.17.2.5.9not-accessiblecurrent
pmPowerMgmtPhasesTableEntry
OBJECT-TYPE
each entry has the information about the phases.
1.3.6.1.4.1.10418.17.2.5.9.1not-accessiblecurrent
pmPowerMgmtPhasesTablePortNumber
OBJECT-TYPE
Serial Port number.
1.3.6.1.4.1.10418.17.2.5.9.1.1InterfaceIndexread-onlycurrent
pmPowerMgmtPhasesTablePduNumber
OBJECT-TYPE
Index.
1.3.6.1.4.1.10418.17.2.5.9.1.2InterfaceIndexread-onlycurrent
pmPowerMgmtPhasesTableNumber
OBJECT-TYPE
Number of the phase in the PDU.
1.3.6.1.4.1.10418.17.2.5.9.1.3InterfaceIndexread-onlycurrent
pmPowerMgmtPhasesTableName
OBJECT-TYPE
Name of the phase. Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.9.1.4DisplayStringread-onlycurrent
pmPowerMgmtPhasesTablePortName
OBJECT-TYPE
Serial Port Name where the PDU is connected.
1.3.6.1.4.1.10418.17.2.5.9.1.5DisplayStringread-onlycurrent
pmPowerMgmtPhasesTablePduId
OBJECT-TYPE
PDU identification.
1.3.6.1.4.1.10418.17.2.5.9.1.6DisplayStringread-onlycurrent
pmPowerMgmtPhasesTableAlarm
OBJECT-TYPE
Show the phase alarm status. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.45INTEGER {normal(1), blow-fuse(2), hw-ocp(3), high-critical(4), high-warning(5), low-warning(6), low-critical(7)}read-onlycurrent
pmPowerMgmtPhasesTableCurrentValue
OBJECT-TYPE
Actual value of current in the phase (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.50Integer32read-onlycurrent
pmPowerMgmtPhasesTableCurrentMax
OBJECT-TYPE
Maximum value of current in the phase (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.51Integer32read-onlycurrent
pmPowerMgmtPhasesTableCurrentMin
OBJECT-TYPE
Minimum value of current in the phase (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.52Integer32read-onlycurrent
pmPowerMgmtPhasesTableCurrentAvg
OBJECT-TYPE
Average value of current in the phase (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.53Integer32read-onlycurrent
pmPowerMgmtPhasesTableCurrentReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.9.1.54INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPhasesTablePowerValue
OBJECT-TYPE
Actual value of power in the phase (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.60Integer32read-onlycurrent
pmPowerMgmtPhasesTablePowerMax
OBJECT-TYPE
Maximum value of power in the phase (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.61Integer32read-onlycurrent
pmPowerMgmtPhasesTablePowerMin
OBJECT-TYPE
Minimum value of power in the phase (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.62Integer32read-onlycurrent
pmPowerMgmtPhasesTablePowerAvg
OBJECT-TYPE
Average value of power in the phase (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.63Integer32read-onlycurrent
pmPowerMgmtPhasesTablePowerReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.9.1.64INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPhasesTablePowerType
OBJECT-TYPE
Type of power values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.65INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtPhasesTableVoltageValue
OBJECT-TYPE
Actual value of voltage in the phase (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.70Integer32read-onlycurrent
pmPowerMgmtPhasesTableVoltageMax
OBJECT-TYPE
Maximum value of voltage in the phase (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.71Integer32read-onlycurrent
pmPowerMgmtPhasesTableVoltageMin
OBJECT-TYPE
Minimum value of voltage in the phase (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.72Integer32read-onlycurrent
pmPowerMgmtPhasesTableVoltageAvg
OBJECT-TYPE
Average value of voltage in the phase (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.73Integer32read-onlycurrent
pmPowerMgmtPhasesTableVoltageReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.9.1.74INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPhasesTableVoltageType
OBJECT-TYPE
Type of voltage values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.75INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtPhasesTablePowerFactorValue
OBJECT-TYPE
Actual value of power factor in the phase (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.80Integer32read-onlycurrent
pmPowerMgmtPhasesTablePowerFactorMax
OBJECT-TYPE
Maximum value of power factor in the phase (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.81Integer32read-onlycurrent
pmPowerMgmtPhasesTablePowerFactorMin
OBJECT-TYPE
Minimum value of power factor in the phase (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.82Integer32read-onlycurrent
pmPowerMgmtPhasesTablePowerFactorAvg
OBJECT-TYPE
Average value of power factor in the phase (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.83Integer32read-onlycurrent
pmPowerMgmtPhasesTablePowerFactorReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.9.1.84INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtPhasesTablePowerFactorType
OBJECT-TYPE
Type of power factor values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.85INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtPhasesTableCurrentHighCritical
OBJECT-TYPE
phase high critical (alarm) current threshold (A x 10). Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.100Integer32read-writecurrent
pmPowerMgmtPhasesTableCurrentHighWarning
OBJECT-TYPE
phase high warning current threshold (A x 10). Set fails if value is higher than CurrentHighCritical or lower than CurrentLowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.101Integer32read-writecurrent
pmPowerMgmtPhasesTableCurrentLowWarning
OBJECT-TYPE
phase low warning current threshold (A x 10). Set fails if value is higher than CurrentHighWarning or lower than CurrentLowCritical. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.102Integer32read-writecurrent
pmPowerMgmtPhasesTableCurrentLowCritical
OBJECT-TYPE
phase low critical current threshold (A x 10). Set fails if value is higher than CurrentLowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.9.1.103Integer32read-writecurrent
pmPowerMgmtTotalNumberOfBanks
OBJECT-TYPE
Number of banks managed by the appliance.
1.3.6.1.4.1.10418.17.2.5.10Integer32read-onlycurrent
pmPowerMgmtBanksTable
OBJECT-TYPE
This table contains the information about banks.
1.3.6.1.4.1.10418.17.2.5.11not-accessiblecurrent
pmPowerMgmtBanksTableEntry
OBJECT-TYPE
each entry has the information about the banks.
1.3.6.1.4.1.10418.17.2.5.11.1not-accessiblecurrent
pmPowerMgmtBanksTablePortNumber
OBJECT-TYPE
Serial Port number.
1.3.6.1.4.1.10418.17.2.5.11.1.1InterfaceIndexread-onlycurrent
pmPowerMgmtBanksTablePduNumber
OBJECT-TYPE
Index.
1.3.6.1.4.1.10418.17.2.5.11.1.2InterfaceIndexread-onlycurrent
pmPowerMgmtBanksTableNumber
OBJECT-TYPE
Number of the bank in the PDU.
1.3.6.1.4.1.10418.17.2.5.11.1.3InterfaceIndexread-onlycurrent
pmPowerMgmtBanksTableName
OBJECT-TYPE
Name of the bank.
1.3.6.1.4.1.10418.17.2.5.11.1.4DisplayStringread-onlycurrent
pmPowerMgmtBanksTablePortName
OBJECT-TYPE
Serial Port Name where the PDU is connected.
1.3.6.1.4.1.10418.17.2.5.11.1.5DisplayStringread-onlycurrent
pmPowerMgmtBanksTablePduId
OBJECT-TYPE
PDU identification.
1.3.6.1.4.1.10418.17.2.5.11.1.6DisplayStringread-onlycurrent
pmPowerMgmtBanksTableAlarm
OBJECT-TYPE
Show the bank alarm status. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.45INTEGER {normal(1), blow-fuse(2), hw-ocp(3), high-critical(4), high-warning(5), low-warning(6), low-critical(7)}read-onlycurrent
pmPowerMgmtBanksTableCurrentValue
OBJECT-TYPE
Actual value of current in the bank (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.50Integer32read-onlycurrent
pmPowerMgmtBanksTableCurrentMax
OBJECT-TYPE
Maximum value of current in the bank (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.51Integer32read-onlycurrent
pmPowerMgmtBanksTableCurrentMin
OBJECT-TYPE
Minimum value of current in the bank (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.52Integer32read-onlycurrent
pmPowerMgmtBanksTableCurrentAvg
OBJECT-TYPE
Average value of current in the bank (A x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.53Integer32read-onlycurrent
pmPowerMgmtBanksTableCurrentReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.11.1.54INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtBanksTablePowerValue
OBJECT-TYPE
Actual value of power in the bank (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.60Integer32read-onlycurrent
pmPowerMgmtBanksTablePowerMax
OBJECT-TYPE
Maximum value of power in the bank (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.61Integer32read-onlycurrent
pmPowerMgmtBanksTablePowerMin
OBJECT-TYPE
Minimum value of power in the bank (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.62Integer32read-onlycurrent
pmPowerMgmtBanksTablePowerAvg
OBJECT-TYPE
Average value of power in the bank (W x 10). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.63Integer32read-onlycurrent
pmPowerMgmtBanksTablePowerReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.11.1.64INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtBanksTablePowerType
OBJECT-TYPE
Type of power values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.65INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtBanksTableVoltageValue
OBJECT-TYPE
Actual value of voltage in the bank (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.70Integer32read-onlycurrent
pmPowerMgmtBanksTableVoltageMax
OBJECT-TYPE
Maximum value of voltage in the bank (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.71Integer32read-onlycurrent
pmPowerMgmtBanksTableVoltageMin
OBJECT-TYPE
Minimum value of voltage in the bank (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.72Integer32read-onlycurrent
pmPowerMgmtBanksTableVoltageAvg
OBJECT-TYPE
Average value of voltage in the bank (V). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.73Integer32read-onlycurrent
pmPowerMgmtBanksTableVoltageReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.11.1.74INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtBanksTableVoltageType
OBJECT-TYPE
Type of voltage values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.75INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtBanksTablePowerFactorValue
OBJECT-TYPE
Actual value of power factor in the bank (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.80Integer32read-onlycurrent
pmPowerMgmtBanksTablePowerFactorMax
OBJECT-TYPE
Maximum value of power factor in the bank (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.81Integer32read-onlycurrent
pmPowerMgmtBanksTablePowerFactorMin
OBJECT-TYPE
Minimum value of power factor in the bank (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.82Integer32read-onlycurrent
pmPowerMgmtBanksTablePowerFactorAvg
OBJECT-TYPE
Average value of power factor in the bank (Pf x 100). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.83Integer32read-onlycurrent
pmPowerMgmtBanksTablePowerFactorReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.11.1.84INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtBanksTablePowerFactorType
OBJECT-TYPE
Type of power factor values. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.85INTEGER {none-sensor(0), estimated(1), measured(2)}read-onlycurrent
pmPowerMgmtBanksTableCurrentHighCritical
OBJECT-TYPE
bank high critical (alarm) current threshold (A x 10). Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.100Integer32read-writecurrent
pmPowerMgmtBanksTableCurrentHighWarning
OBJECT-TYPE
bank high warning current threshold (A x 10). Set fails if value is higher than CurrentHighCritical or lower than CurrentLowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.101Integer32read-writecurrent
pmPowerMgmtBanksTableCurrentLowWarning
OBJECT-TYPE
bank low warning current threshold (A x 10). Set fails if value is higher than CurrentHighWarning or lower than CurrentLowCritical. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.102Integer32read-writecurrent
pmPowerMgmtBanksTableCurrentLowCritical
OBJECT-TYPE
bank low critical current threshold (A x 10). Set fails if value is higher than CurrentLowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.103Integer32read-writecurrent
pmPowerMgmtBanksTableEnergyValue
OBJECT-TYPE
bank energy value (Wh). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.11.1.105Integer32read-onlycurrent
pmPowerMgmtBanksTableEnergyStartTime
OBJECT-TYPE
time at which energy calculation commenced (ISO8601 format). Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.11.1.106DisplayStringread-onlycurrent
pmPowerMgmtBanksTableEnergyReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to PDU.
1.3.6.1.4.1.10418.17.2.5.11.1.107INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtTotalNumberOfSensors
OBJECT-TYPE
Number of Sensors managed by the appliance.
1.3.6.1.4.1.10418.17.2.5.12Integer32read-onlycurrent
pmPowerMgmtSensorsTable
OBJECT-TYPE
This table contains the information about sensors.
1.3.6.1.4.1.10418.17.2.5.13not-accessiblecurrent
pmPowerMgmtSensorsTableEntry
OBJECT-TYPE
each entry has the information about the sensors.
1.3.6.1.4.1.10418.17.2.5.13.1not-accessiblecurrent
pmPowerMgmtSensorsTablePortNumber
OBJECT-TYPE
Serial Port number.
1.3.6.1.4.1.10418.17.2.5.13.1.1InterfaceIndexread-onlycurrent
pmPowerMgmtSensorsTablePduNumber
OBJECT-TYPE
Index.
1.3.6.1.4.1.10418.17.2.5.13.1.2InterfaceIndexread-onlycurrent
pmPowerMgmtSensorsTableNumber
OBJECT-TYPE
Number of the sensor in the PDU.
1.3.6.1.4.1.10418.17.2.5.13.1.3InterfaceIndexread-onlycurrent
pmPowerMgmtSensorsTableName
OBJECT-TYPE
Name of the sensor.
1.3.6.1.4.1.10418.17.2.5.13.1.4DisplayStringread-writecurrent
pmPowerMgmtSensorsTablePortName
OBJECT-TYPE
Serial Port Name where the PDU is connected.
1.3.6.1.4.1.10418.17.2.5.13.1.5DisplayStringread-onlycurrent
pmPowerMgmtSensorsTablePduId
OBJECT-TYPE
PDU identification.
1.3.6.1.4.1.10418.17.2.5.13.1.6DisplayStringread-onlycurrent
pmPowerMgmtSensorsTableType
OBJECT-TYPE
The type of environmental monitor. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.7INTEGER {temp-internal(1), temperature(2), humidity(3), air-flow(4), smoke(5), dry-concact(6), water-level(7), motion(8), unplugged(9), unknown(10)}read-onlycurrent
pmPowerMgmtSensorsTableStatus
OBJECT-TYPE
Status of digital sensors: Dry-Contact, Water level, Smoke sensor, Motion sensor. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.8INTEGER {normal(1), triggered(2), not-applicable(3), opened(4), closed(5)}read-onlycurrent
pmPowerMgmtSensorsTableValue
OBJECT-TYPE
Actual value of the sensor. Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.13.1.20DisplayStringread-onlycurrent
pmPowerMgmtSensorsTableValueMax
OBJECT-TYPE
Maximum value of the sensor. Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.13.1.21DisplayStringread-onlycurrent
pmPowerMgmtSensorsTableValueMin
OBJECT-TYPE
Minimum value of the sensor. Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.13.1.22DisplayStringread-onlycurrent
pmPowerMgmtSensorsTableValueAvg
OBJECT-TYPE
Average value of the sensor. Returns N/A if not applicable.
1.3.6.1.4.1.10418.17.2.5.13.1.23DisplayStringread-onlycurrent
pmPowerMgmtSensorsTableValueInt
OBJECT-TYPE
Actual value of the sensor. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.25Integer32read-onlycurrent
pmPowerMgmtSensorsTableValueMaxInt
OBJECT-TYPE
Maximum value of the sensor. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.26Integer32read-onlycurrent
pmPowerMgmtSensorsTableValueMinInt
OBJECT-TYPE
Minimum value of the sensor. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.27Integer32read-onlycurrent
pmPowerMgmtSensorsTableValueAvgInt
OBJECT-TYPE
Average value of the sensor. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.28Integer32read-onlycurrent
pmPowerMgmtSensorsTableValueReset
OBJECT-TYPE
noAction(1) = always returned in a GET. Does nothing if SET. reset(2) = when SET the reset command is sent to sensor.
1.3.6.1.4.1.10418.17.2.5.13.1.30INTEGER {noAction(1), reset(2)}read-writecurrent
pmPowerMgmtSensorsTableHighCritical
OBJECT-TYPE
sensor high critical (alarm) threshold (unit x 10) - use unit as returned by pmPowerMgmtSensorsTableUnit. Set fails if value is lower that CurrentHighWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.40Integer32read-writecurrent
pmPowerMgmtSensorsTableHighWarning
OBJECT-TYPE
sensor high warning threshold (unit x 10) - use unit as returned by pmPowerMgmtSensorsTableUnit. Set fails if value is higher than HighCritical or lower than LowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.41Integer32read-writecurrent
pmPowerMgmtSensorsTableLowWarning
OBJECT-TYPE
sensor low warning threshold (unit x 10) - use unit as returned by pmPowerMgmtSensorsTableUnit. Set fails if value is higher than HighWarning or lower than LowCritical. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.42Integer32read-writecurrent
pmPowerMgmtSensorsTableLowCritical
OBJECT-TYPE
sensor low critical threshold (unit x 10) - use unit as returned by pmPowerMgmtSensorsTableUnit. Set fails if value is higher than LowWarning. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.43Integer32read-writecurrent
pmPowerMgmtSensorsTableUnit
OBJECT-TYPE
sensor unit. Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.45INTEGER {undefined(1), fahrenheit(2), celsius(3), percent(4), afu(5)}read-writecurrent
pmPowerMgmtSensorsTableHighCriticalC
OBJECT-TYPE
sensor high critical (alarm) threshold (Celcius x 10). to SET: use pmPowerMgmtSensorsTableHighCritical in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.50Integer32read-onlycurrent
pmPowerMgmtSensorsTableHighWarningC
OBJECT-TYPE
sensor high warning threshold (Celcius x 10). to SET: use pmPowerMgmtSensorsTableHighWarning in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.51Integer32read-onlycurrent
pmPowerMgmtSensorsTableLowWarningC
OBJECT-TYPE
sensor low warning threshold (Celcius x 10). to SET: use pmPowerMgmtSensorsTableLowWarning in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.52Integer32read-onlycurrent
pmPowerMgmtSensorsTableLowCriticalC
OBJECT-TYPE
sensor low critical threshold (Celcius x 10). to SET: use pmPowerMgmtSensorsTableLowCritical in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.53Integer32read-onlycurrent
pmPowerMgmtSensorsTableHighCriticalF
OBJECT-TYPE
sensor high critical (alarm) threshold (Fahrenheit x 10). to SET: use pmPowerMgmtSensorsTableHighCritical in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.60Integer32read-onlycurrent
pmPowerMgmtSensorsTableHighWarningF
OBJECT-TYPE
sensor high warning threshold (Fahrenheit x 10). to SET: use pmPowerMgmtSensorsTableHighWarning in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.61Integer32read-onlycurrent
pmPowerMgmtSensorsTableLowWarningF
OBJECT-TYPE
sensor low warning threshold (Fahrenheit x 10). to SET: use pmPowerMgmtSensorsTableLowWarning in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.62Integer32read-onlycurrent
pmPowerMgmtSensorsTableLowCriticalF
OBJECT-TYPE
sensor low critical threshold (Fahrenheit x 10). to SET: use pmPowerMgmtSensorsTableLowCritical in proper units (pmPowerMgmtSensorsTableUnit). Returns 0 if not supported.
1.3.6.1.4.1.10418.17.2.5.13.1.63Integer32read-onlycurrent
pmTrapObject
OBJECT-IDENTITY
1.3.6.1.4.1.10418.17.2.6