MIBs Depot

PERLE-MCR-MGT-MIB

Registered at
1.3.6.1.4.1.1966
Last updated
2014-09-03 00:00
Organization
Perle Systems Limited
Revisions
2014-09-03 00:00, 2013-03-02 00:00, 2012-11-15 00:00, 2012-02-01 00:00, 2011-01-20 00:00, 2011-01-12 00:00, 2010-09-10 00:00
Namespace
perle
Source file
PERLE-MCR-MGT-MIB
Digest
sha256:4a5571ab3bdf3d6b6029fc4162c82f1fffe04b9ee8978e2cd2897d8cd9a66913

Description

The private MIB module for the Perle Managed Media Converters

Contact

Postal: Perle Systems Limited 60 Renfrew Drive Markham, Ontario Canada L3R 0E1 http://www.perle.com/

Imports

FromSymbols
SNMP-FRAMEWORK-MIBSnmpEngineID
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter32, Counter64, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

PERLE-MCR-MGT-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
AlertSeverityLevel
TEXTUAL-CONVENTION
The alert severity level of an event.
current
ContainerStatus
TEXTUAL-CONVENTION
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module. 6-Indicates that the changes in the container folder are to be discarded.
current
EnableDisableValue
TEXTUAL-CONVENTION
Represents an ON or OFF value.
current
GenericTableIndex
TEXTUAL-CONVENTION
An arbitrary value that uniquely identifies the entity. The value should be a small, positive integer. Index values for different entities are not necessarily contiguous.
current
Ipv4v6Address
TEXTUAL-CONVENTION
An IPv4 or IPv6 address
current
OnOffValue
TEXTUAL-CONVENTION
Represents an ON or OFF value.
current
SlotNumber
TEXTUAL-CONVENTION
Chassis slot number. Valid values are 1 to the highest slot number the chassis supports. For example a MCR-1900 chassis the valid slot numbers are 1 to 19
current
YesNoValue
TEXTUAL-CONVENTION
Represents a YES or NO value.
current

Objects

NameOIDSyntaxAccessStatus
perle
OBJECT-IDENTITY
1.3.6.1.4.1.1966
productId
OBJECT-IDENTITY
1.3.6.1.4.1.1966.20
mediaConverter
OBJECT-IDENTITY
1.3.6.1.4.1.1966.20.1
mcrMGT
OBJECT-IDENTITY
1.3.6.1.4.1.1966.20.1.1
productMIB
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21
mediaconverterMIB
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1
mcrMGTMIBNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.0
mcrMGTMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1
mcrChassisGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1
mcrChassisTable
OBJECT-TYPE
Table of chassis diagnostic type information.
1.3.6.1.4.1.1966.21.1.1.1.1.1not-accessiblecurrent
mcrChassisEntry
OBJECT-TYPE
Entries of the table, each relating to a separate chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.1.1not-accessiblecurrent
mcrChassisIndex
OBJECT-TYPE
This object identifies the chassis number.
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.1Unsigned32accessible-for-notifycurrent
chassisModelName
OBJECT-TYPE
This object identifies the name of the chassis model. For the 2-slot chassis, this is the product model.
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.2DisplayStringread-onlycurrent
chassisModelDesc
OBJECT-TYPE
This object identifies a static description of the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.3DisplayStringread-onlycurrent
chassisSerialNumber
OBJECT-TYPE
This object identifies the chassis serial number. For the 2-slot chassis, this is writeable (and user-defined). For other chassis, this is read-only (and reflects the chassis' actual serial number).
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.4DisplayString (SIZE(0..16))read-writecurrent
chassisBootloaderVersion
OBJECT-TYPE
This object identifies the chassis bootloader version. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.5DisplayStringread-onlycurrent
chassisFirmwareVersion
OBJECT-TYPE
This object identifies the chassis firmware version. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.6DisplayStringread-onlycurrent
chassisOutStandWarnAlarms
OBJECT-TYPE
This object identifies the number of outstanding warnings and alarms for this chassis. If this value is not zero then user intervention is needed to resolve the outstanding warnings and alarms. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.7Unsigned32read-onlycurrent
chassisDiagStatus
OBJECT-TYPE
This object identifies the chassis self-test diagnostics result. It will return zero if it passed and non-zero error code if it failed. The following are possible non-zero error codes: 1 - Firmware download required 2 - Temperature sensor not functional (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.8Unsigned32read-onlycurrent
chassisTemperature
OBJECT-TYPE
This object identifies the current temperature of the chassis. The temperature returned will be either Celsius or Fahrenheit based on your current regional display settings. If the temperature returned is -1 then a problem with the temperature sensor has occurred and the current temperature is unknown. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.9Integer32read-onlycurrent
chassisCfgHighTempThreshold
OBJECT-TYPE
This object identifies the chassis temperature high threshold. If the chassis temperature exceeds this threshold then an alert will be generated. The value read/written will be either Celsius or Fahrenheit based on your current regional display settings. The valid range for this threshold is 0 to 70 degrees Celsius or 32 to 158 degrees Fahrenheit. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.10Integer32read-writecurrent
chassisReset
OBJECT-TYPE
This object allows the resetting of the chassis (all modules). Reading this object always returns 0.
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.11YesNoValueread-writecurrent
chassisCfgMgmtSlot
OBJECT-TYPE
For the 2-slot chassis, this is the configured slot index of the management module. This value only needs to be changed if the management module is physically installed in slot 2, rather than slot 1. The management module should be restarted after changing this value.
1.3.6.1.4.1.1966.21.1.1.1.1.1.1.12Unsigned32 (1..2)read-writecurrent
mcrPsmuTable
OBJECT-TYPE
Table of PSMU (Power Supply Monitoring Unit) diagnostic type information. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.2not-accessiblecurrent
mcrPsmuEntry
OBJECT-TYPE
Entries of the table, each relating to a separate PSMU.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1not-accessiblecurrent
mcrPsmuIndex
OBJECT-TYPE
This object identifies the PSMU bay as either A or B.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.2INTEGER {a(1), b(2)}accessible-for-notifycurrent
mcrPsmuModelName
OBJECT-TYPE
This object identifies the PSMU model.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.3DisplayStringread-onlycurrent
mcrPsmuModelDesc
OBJECT-TYPE
This object identifies a static description of the power supply model present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.4DisplayStringread-onlycurrent
mcrPsmuPsuSerialNumber
OBJECT-TYPE
This object identifies the PSU serial number.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.5DisplayString (SIZE(0..16))read-onlycurrent
mcrPsmuBootloaderVersion
OBJECT-TYPE
This object identifies the PSMU bootloader version.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.6DisplayStringread-onlycurrent
mcrPsmuFirmwareVersion
OBJECT-TYPE
This object identifies the PSMU firmware version.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.7DisplayStringread-onlycurrent
mcrPsmuOutStandWarnAlarms
OBJECT-TYPE
This object identifies the number of outstanding warnings and alarms for this chassis. If this value is not zero then user intervention is needed to resolve the outstanding warnings and alarms
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.8Unsigned32read-onlycurrent
mcrPsmuPsuStatus
OBJECT-TYPE
This object identifies if the PSMU power supply unit (PSU) status.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.9INTEGER {notPresent(0), good(1), fail(2)}read-onlycurrent
mcrPsmuPsuVoltage
OBJECT-TYPE
This object identifies the current PSU voltage being supplied.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.10DisplayStringread-onlycurrent
mcrPsmuPsuPowerUsage
OBJECT-TYPE
This object identifies power currently being supplied to the chassis, in milliwatts. A value of 0 indicate that the power supply is not in use
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.11DisplayStringread-onlycurrent
mcrPsmuFanStatus
OBJECT-TYPE
This object identifies the fan status.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.12INTEGER {notPresent(0), good(1), fail(2)}read-onlycurrent
mcrPsmuFanSpeed
OBJECT-TYPE
This object identifies the speed of the fan in RPM.
1.3.6.1.4.1.1966.21.1.1.1.1.2.1.13Unsigned32read-onlycurrent
mcrChassisSlotTable
OBJECT-TYPE
Table of chassis slot configuration, status and diagnostic type information.
1.3.6.1.4.1.1966.21.1.1.1.1.3not-accessiblecurrent
mcrChassisSlotEntry
OBJECT-TYPE
Entries of the table, each relating to a separate slot in a chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1not-accessiblecurrent
mcrChassisSlotIndex
OBJECT-TYPE
This object identifies the chassis slot number.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.2SlotNumberaccessible-for-notifycurrent
mcrUserDefinedModuleName
OBJECT-TYPE
This object identifies the user defined name of the module inserted in the slot. The default name is the model name of the media converter module
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.3DisplayStringread-onlycurrent
mcrModuleModelName
OBJECT-TYPE
This object identifies the model name of the module inserted in the slot.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.4DisplayStringread-onlycurrent
mcrUnManagedModuleSlotName
OBJECT-TYPE
This object identifies the user defined name for an unmanaged module inserted in the slot. Unmanaged modules include all perle C-1000, C-100, C-1110 and c-110 type modules.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.5DisplayStringread-writecurrent
mcrModuleSerialNumber
OBJECT-TYPE
This object identifies the serial number of the module inserted in the slot.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.6DisplayString (SIZE(0..16))read-onlycurrent
mcrModuleBootloaderVersion
OBJECT-TYPE
This object identifies the bootloader version of the module inserted in the slot.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.7DisplayStringread-onlycurrent
mcrModuleFirmwareVersion
OBJECT-TYPE
This object identifies the firmware version of the module inserted in the slot.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.8DisplayStringread-onlycurrent
mcrModuleoOutStandWarnAlarms
OBJECT-TYPE
This object identifies the number of outstanding warnings and alarms for this module. If this value is not zero then user intervention is needed to resolve the outstanding warnings and alarms
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.9Unsigned32read-onlycurrent
mcrModuleDiagStatus
OBJECT-TYPE
This object identifies the module's self-test diagnostics result. It will return zero if it passed and non-zero error code if the module has failed.The following are possible non-zero error codes: 1 - Media converter module's PHY is not functional. 2 - Firmware download required
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.10Integer32read-onlycurrent
mcrModuleTypeInserted
OBJECT-TYPE
This object identifies the module type inserted for this chassis slot.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.11INTEGER {unManaged(-3), mcrMgt(-2), unknown(-1), empty(0), cm1000Fixed(1), cm100Fixed(2), cm1110RateConv(3), cm110RateConv(4), cm100mmFixed(5), cm1000mmFixed(6), cm10gFixed(7), exCM(8), cm10gt(9), cm4gpt(10)}read-onlycurrent
mcrMediaConfigBackupRestore
OBJECT-TYPE
This object is applicable to media converter modules only. It identifies whether the media configuration will be automatically backed up to or restored from the management card's non-volatile memory
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.12INTEGER {disable(0), enable(1), notApplicable(2)}read-writecurrent
mcrMediaBackedupModuleType
OBJECT-TYPE
This object identifies the media converter module type of the configuration that was backed up for the slot on the management card's non-volatile memory when the mcrMediaConfigBackupRestore object was enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.13INTEGER {none(0), cm1000Fixed(1), cm100Fixed(2), cm1110RateConv(3), cm110RateConv(4), cm100mmFixed(5), cm1000mmFixed(6), cm10gFixed(7), exCM(8), cm10gt(9), cm4gpt(10)}read-onlycurrent
mcrChassisPwrUpSlotPwrState
OBJECT-TYPE
This object identifies the default power state of the slot when the chassis is initially powered up. The current power state of the slot can be manually changed by writing to mcrCurrentPowerState object or dynamically changed via slot power schedule configuration. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.14OnOffValueread-writecurrent
mcrCurrentPowerState
OBJECT-TYPE
Writing this object allows the current power state of the slot to be turned on or off. This object is not writable for management modules or the 2-slot chassis. Reading this object will return the current slot power state.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.15OnOffValueread-writecurrent
mcrPowerScheduleEnable
OBJECT-TYPE
This object is not applicable to management modules. It identifies if power schedule is enabled for the slot. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.16INTEGER {no(0), yes(1), notApplicable(2)}read-writecurrent
mcrModuleReset
OBJECT-TYPE
This object allows you to reset the module inserted in the slot.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.17INTEGER {no(0), yes(1), notApplicable(2)}read-writecurrent
mcrModuleResetToFactory
OBJECT-TYPE
This object allows you to reset to factory the module inserted in the slot.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.18INTEGER {no(0), yes(1), notApplicable(2)}read-writecurrent
mcrModuleModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the slot.
1.3.6.1.4.1.1966.21.1.1.1.1.3.1.19DisplayStringread-onlycurrent
mcrModuleTypes
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4
cm1000Fixed
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.1
cm1000FixedTable
OBJECT-TYPE
Table of CM-1000 type media converter module's status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1not-accessiblecurrent
cm1000FixedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1000 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1not-accessiblecurrent
cm1000SlotIndex
OBJECT-TYPE
The Slot number the CM-1000 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.2SlotNumbernot-accessiblecurrent
cm1000Modelname
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.3DisplayStringread-onlycurrent
cm1000ModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.4DisplayStringread-onlycurrent
cm1000HwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware jumper J5 on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media converter module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm1000HwSw1FiberAutoNeg
OBJECT-TYPE
Media converter module's current switch setting for fiber Auto-Negotiation.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.6INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm1000HwSw2LinkMode
OBJECT-TYPE
Media converter module's current switch setting for Link Mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.7INTEGER {swDownSmartLinkPassthrough(0), swUpStandard(1)}read-onlycurrent
cm1000HwSw3FiberFaultAlert
OBJECT-TYPE
Media converter module's current switch setting for Fiber Fault Alert.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.8INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm1000HwSw4Duplex
OBJECT-TYPE
Media converter module's current switch setting for copper duplex.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.9INTEGER {swDownHalf(0), swUpAuto(1)}read-onlycurrent
cm1000HwSw5Pause
OBJECT-TYPE
Media converter module's current switch setting for copper pause (flow control).
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.10INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm1000HwSw6Loopback
OBJECT-TYPE
Media converter module's current switch setting for fiber loopback mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.11INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
cm1000FiberLinkStatus
OBJECT-TYPE
Media converter module's current fiber link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.12INTEGER {down(0), up(1)}read-onlycurrent
cm1000FiberConnType
OBJECT-TYPE
Media converter module's fiber port connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.13INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6)}read-onlycurrent
cm1000FiberAutoNegState
OBJECT-TYPE
Media converter module's current fiber auto-negotiation state.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.14INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm1000FiberSpeed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.15INTEGER {speed1000Mbps(2)}read-onlycurrent
cm1000FiberDuplex
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.16INTEGER {half(0), full(1)}read-onlycurrent
cm1000FiberPauseEnh
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.17INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm1000FiberLPRFStatus
OBJECT-TYPE
Media converter module's fiber Link Partner Remote Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.18INTEGER {ok(0), offline(1), linkFault(2), autoNegError(3)}read-onlycurrent
cm1000FiberReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.19INTEGER {fault(0), ok(1)}read-writecurrent
cm1000FiberLoopBack
OBJECT-TYPE
Media converter module's current fiber loopback mode setting. Writing to this object will change the current settings. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.20EnableDisableValueread-writecurrent
cm1000CopperLinkStatus
OBJECT-TYPE
Media converter module's current copper link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.21INTEGER {down(0), up(1)}read-onlycurrent
cm1000CopperConnType
OBJECT-TYPE
Media converter module's copper connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.22INTEGER {rj45(0)}read-onlycurrent
cm1000CopperAutoNegState
OBJECT-TYPE
Media converter module's current copper auto-negotiation state.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.23INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm1000CopperSpeed
OBJECT-TYPE
Media converter module's copper port speed in megabits per second.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.24INTEGER {speed1000Mbps(2)}read-onlycurrent
cm1000CopperDuplex
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.25INTEGER {half(0), full(1)}read-onlycurrent
cm1000CopperCrossOver
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated MDI/MDI-X setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.26INTEGER {mdi(0), mdix(1)}read-onlycurrent
cm1000CopperPauseEnh
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.27INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm1000CopperLPRFStatus
OBJECT-TYPE
Media converter module's copper Link Partner Remote Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.1.1.28INTEGER {ok(0), remoteFault(1)}read-onlycurrent
cm1000ConfigTable
OBJECT-TYPE
Table of CM-1000 type media converter module's configuration type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2not-accessiblecurrent
cm1000ConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1000 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1not-accessiblecurrent
cm1000ConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-1000 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.2SlotNumbernot-accessiblecurrent
cm1000ConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.3ContainerStatusread-writecurrent
cm1000ConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm1000ConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.5INTEGER {standard(0), smartLinkPassthrough(1)}read-writecurrent
cm1000ConfigFiberFaultAlert
OBJECT-TYPE
This object identifies the Fiber Fault Alert setting for the media module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.6EnableDisableValueread-writecurrent
cm1000ConfigJumboPackets
OBJECT-TYPE
This object identifies the Jumbo Packet setting for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.7EnableDisableValueread-writecurrent
cm1000ConfigFiberPortName
OBJECT-TYPE
This object identifies a user definable name for the fiber port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.8DisplayString (SIZE(0..8))read-writecurrent
cm1000ConfigFiberPortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.9YesNoValueread-writecurrent
cm1000ConfigFiberAutoNeg
OBJECT-TYPE
This object identifies the wither fiber auto-negotiation is enabled. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.10EnableDisableValueread-writecurrent
cm1000ConfigCopperPortName
OBJECT-TYPE
This object identifies a user definable name for the copper port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.11DisplayString (SIZE(0..8))read-writecurrent
cm1000ConfigCopperPortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.12YesNoValueread-writecurrent
cm1000ConfigCopperDuplex
OBJECT-TYPE
This object identifies the duplex settings for the copper port. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.13INTEGER {half(1), auto(2)}read-writecurrent
cm1000ConfigCopperPauseEnh
OBJECT-TYPE
This object identifies the copper pause (flow control) setting that is a advertised. The settings can be disabled, advertise symmetrical, advertise asymmetrical TX or advertise symmetrical and asymmetrical RX. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.14INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), symmAsymRx(3)}read-writecurrent
cm1000ConfigCopperLowPower
OBJECT-TYPE
This object identifies the copper low power setting for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.2.1.15OnOffValueread-writecurrent
cm1000LedTable
OBJECT-TYPE
Table of CM-1000 type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.3not-accessiblecurrent
cm1000LedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1000 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.3.1not-accessiblecurrent
cm1000LedSlotIndex
OBJECT-TYPE
The Slot number the CM-1000 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.3.1.2SlotNumbernot-accessiblecurrent
cm1000LedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Fiber loopback enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm1000LedLKF
OBJECT-TYPE
This object identifies the status of the link copper (LKC) LED on the media converter module. Possible status values are: off(0) - No fiber link on(1) - Fiber link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.3.1.4INTEGER {off(0), on(1)}read-onlycurrent
cm1000LedLKC
OBJECT-TYPE
This object identifies the status of the link copper (LKC) LED on the media converter module. Possible status values are: off(0) - No copper link on(1) - Copper link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.1.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
cm100Fixed
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.2
cm100FixedTable
OBJECT-TYPE
Table of CM-100 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1not-accessiblecurrent
cm100FixedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1000 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1not-accessiblecurrent
cm100SlotIndex
OBJECT-TYPE
The Slot number the CM-100 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.2SlotNumbernot-accessiblecurrent
cm100ModelName
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.3DisplayStringread-onlycurrent
cm100ModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.4DisplayStringread-onlycurrent
cm100HwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware switch on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm100HwJmp6AutoMDI
OBJECT-TYPE
This object identifies the media converter module's hardware Auto MDIX jumper settings.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.6INTEGER {mdi(0), auto(1)}read-onlycurrent
cm100HwSw1AutoNegotiation
OBJECT-TYPE
Media converter module's current switch setting for fiber Auto-Negotiation.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.7INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm100HwSw2LinkMode
OBJECT-TYPE
Media converter module's current switch setting for Link Mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.8INTEGER {swDownStandardMode(0), swUpLinkPassthroughMode(1)}read-onlycurrent
cm100HwSw3FarEndFault
OBJECT-TYPE
Media converter module's current switch setting for Far End Fault.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.9INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm100HwSw5Pause
OBJECT-TYPE
Media converter module's current switch setting for copper pause (flow control).
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.10INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm100HwSw6Loopback
OBJECT-TYPE
Media converter module's current switch setting for fiber loopback mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.11INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
cm100FiberLinkStatus
OBJECT-TYPE
Media converter module's current fiber link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.12INTEGER {down(0), up(1)}read-onlycurrent
cm100FiberConnType
OBJECT-TYPE
Media converter module's fiber port connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.13INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6)}read-onlycurrent
cm100FiberSpeed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.14INTEGER {speed100Mbps(1)}read-onlycurrent
cm100FiberFarEndFault
OBJECT-TYPE
Media converter module's current fiber Far End Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.15INTEGER {disable(0), ok(1), receivingFEF(2), sendingFEF(3)}read-onlycurrent
cm100FiberReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.16INTEGER {fault(0), ok(1)}read-writecurrent
cm100FiberLoopBack
OBJECT-TYPE
This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.17EnableDisableValueread-writecurrent
cm100CopperLinkStatus
OBJECT-TYPE
Media converter module's current copper link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.18INTEGER {down(0), up(1)}read-onlycurrent
cm100CopperConnType
OBJECT-TYPE
Media converter module's copper connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.19INTEGER {rj45(0)}read-onlycurrent
cm100CopperAutoNegState
OBJECT-TYPE
Media converter module's current copper auto-negotiation state.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.20INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm100CopperSpeed
OBJECT-TYPE
This object identifies the copper port speed in megabits per second.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.21INTEGER {speed100Mbps(1)}read-onlycurrent
cm100CopperDuplex
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.22INTEGER {half(0), full(1)}read-onlycurrent
cm100CopperCrossOver
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated MDI/MDI-X setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.23INTEGER {mdi(0), mdix(1)}read-onlycurrent
cm100CopperPause
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated pause (flow control) setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.24INTEGER {disabled(0), symmetrical(1)}read-onlycurrent
cm100CopperLPRFStatus
OBJECT-TYPE
Media converter module's copper Link Partner Remote Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.1.1.25INTEGER {ok(0), remoteFault(1)}read-onlycurrent
cm100ConfigTable
OBJECT-TYPE
Table of CM-100 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2not-accessiblecurrent
cm100ConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1000 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1not-accessiblecurrent
cm100ConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-1000 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.2SlotNumbernot-accessiblecurrent
cm100ConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.3ContainerStatusread-writecurrent
cm100ConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm100ConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.5INTEGER {standard(0), linkPassthrough(1)}read-writecurrent
cm100ConfigFiberFarEndFault
OBJECT-TYPE
This object identifies the fiber Far End Fault setting for the media module. This setting is always enabled if Link Mode is set to linkPassthrough. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.6EnableDisableValueread-writecurrent
cm100ConfigFiberPortName
OBJECT-TYPE
This object identifies a user definable name for the fiber port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.7DisplayString (SIZE(0..8))read-writecurrent
cm100ConfigFiberPortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.8YesNoValueread-writecurrent
cm100ConfigCopperPortName
OBJECT-TYPE
This object identifies a user definable name for the copper port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.9DisplayString (SIZE(0..8))read-writecurrent
cm100ConfigCopperPortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.10YesNoValueread-writecurrent
cm100ConfigCopperAutoNegotiation
OBJECT-TYPE
This object identifies the whether copper auto-negotiation is enabled. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.11EnableDisableValueread-writecurrent
cm100ConfigCopperCrossOver
OBJECT-TYPE
This object identifies the copper MDI/MDI-X setting.This object is read-only if the media converter module's ConfigMode jumper is set to
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.12INTEGER {auto(0), mdi(1), mdix(2)}read-writecurrent
cm100ConfigCopperPause
OBJECT-TYPE
This object identifies the copper's port pause (flow control) settings. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.2.1.13INTEGER {disabled(0), symmetrical(1)}read-writecurrent
cm100LedTable
OBJECT-TYPE
Table of CM-100 type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.3not-accessiblecurrent
cm100LedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-100 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.3.1not-accessiblecurrent
cm100LedSlotIndex
OBJECT-TYPE
The Slot number the CM-100 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.3.1.2SlotNumbernot-accessiblecurrent
cm100LedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Fiber loopback enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm100LedLKF
OBJECT-TYPE
This object identifies the status of the link fiber (LKF) LED on the media converter module. Possible status values are: off(0) - No fiber link on(1) - Fiber link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.3.1.4INTEGER {off(0), on(1)}read-onlycurrent
cm100LedLKC
OBJECT-TYPE
This object identifies the status of the link copper (LKC) LED on the media converter module. Possible status values are: off(0) - No copper link on(1) - Copper link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.2.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
cm1110RateConv
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.3
cm1110RateConvTable
OBJECT-TYPE
Table of CM-1110 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1not-accessiblecurrent
cm1110RateConvEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1not-accessiblecurrent
cm1110SlotIndex
OBJECT-TYPE
The Slot number the CM-1110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.2SlotNumbernot-accessiblecurrent
cm1110ModelName
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.3DisplayStringread-onlycurrent
cm1110ModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.4DisplayStringread-onlycurrent
cm1110HwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware switch on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm1110HwJmp6AutoMDIX
OBJECT-TYPE
This object identifies the media converter module's hardware Auto MDIX jumper settings.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.6INTEGER {mdix(0), auto(1)}read-onlycurrent
cm1110HwSw1TpAutoNegotiation
OBJECT-TYPE
Media converter module's current switch setting for copper Auto-Negotiation.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.7INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm1110HwSw2LinkMode
OBJECT-TYPE
Media converter module's current switch setting for Link Mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.8INTEGER {swDownNormalMode(0), swUpSmartLinkPassthroughMode(1)}read-onlycurrent
cm1110HwSw3FiberFaultAlert
OBJECT-TYPE
Media converter module's current switch setting for Fiber Fault Alert.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.9INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm1110HwSw4TpDuplex
OBJECT-TYPE
Media converter module's current switch setting for copper duplex.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.10INTEGER {swDownHalf(0), swUpFull(1)}read-onlycurrent
cm1110HwSw5TpSpeed
OBJECT-TYPE
Media converter module's current switch setting for Link Mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.11INTEGER {swDown10Mbps(0), swUp100Mbps(1)}read-onlycurrent
cm1110HwSw6FiberAutoNegotiation
OBJECT-TYPE
Media converter module's current switch setting for fiber Auto-Ngotiation. This object is not applicable if there is a 100 Mbps SFP modules inserted.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.12INTEGER {swDownDisabled(0), swUpEnabled(1), notApplicable(2)}read-onlycurrent
cm1110HwSw6FiberSfp100Duplex
OBJECT-TYPE
Media converter module's current switch setting for fiber duplex if a 100 Mbps SFP module is inserted. Otherwise this object is not applicable.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.13INTEGER {swDownHalfDuplex(0), swUpFullDuplex(1), notApplicable(2)}read-onlycurrent
cm1110HwSw7Loopback
OBJECT-TYPE
Media converter module's current switch setting for fiber loopback mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.14INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
cm1110FiberLinkStatus
OBJECT-TYPE
Media converter module's current fiber link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.15INTEGER {down(0), up(1)}read-onlycurrent
cm1110FiberConnType
OBJECT-TYPE
Media converter module's fiber port connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.16INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6)}read-onlycurrent
cm1110FiberAutoNegState
OBJECT-TYPE
Media converter module's current fiber auto-negotiation state. This object is not applicable if the fiber connector type is a 100 Mbps SFP module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.17INTEGER {disabled(0), complete(1), inProgress(2), notApplicable(99)}read-onlycurrent
cm1110FiberSpeed
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.18INTEGER {speed100Mbps(1), speed1000Mbps(2)}read-onlycurrent
cm1110FiberDuplex
OBJECT-TYPE
This object identifies the current fiber port duplex state.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.19INTEGER {half(0), full(1)}read-onlycurrent
cm1110FiberPauseEnh
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.20INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm1110FiberLPRFStatus
OBJECT-TYPE
Media converter module's fiber Link Partner Remote Fault status. This object is not applicable if there is a 100 Mbps SFP module inserted.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.21INTEGER {ok(0), offline(1), linkFault(2), autoNegError(3), notApplicable(99)}read-onlycurrent
cm1110FiberSfp100FarEndFault
OBJECT-TYPE
Media converter module's current fiber Far End Fault status if a 100 Mbps SFP module is inserted. Otherwise this object is not applicable.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.22INTEGER {disable(0), ok(1), receivingFEF(2), sendingFEF(3), notApplicable(99)}read-onlycurrent
cm1110FiberReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.23INTEGER {fault(0), ok(1)}read-writecurrent
cm1110FiberLoopBack
OBJECT-TYPE
This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.24EnableDisableValueread-writecurrent
cm1110CopperLinkStatus
OBJECT-TYPE
Media converter module's current copper link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.25INTEGER {down(0), up(1)}read-onlycurrent
cm1110CopperConnType
OBJECT-TYPE
Media converter module's copper connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.26INTEGER {rj45(0)}read-onlycurrent
cm1110CopperAutoNegState
OBJECT-TYPE
Media converter module's current copper auto-negotiation state.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.27INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm1110CopperSpeed
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated speed setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.28INTEGER {speed10Mbs(0), speed100Mbps(1), speed1000Mbps(2)}read-onlycurrent
cm1110CopperDuplex
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.29INTEGER {half(0), full(1)}read-onlycurrent
cm1110CopperCrossOver
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated MDI/MDI-X setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.30INTEGER {mdi(0), mdix(1)}read-onlycurrent
cm1110CopperPauseEnh
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.31INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm1110CopperLPRFStatus
OBJECT-TYPE
Media converter module's copper Link Partner Remote Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.32INTEGER {ok(0), remoteFault(1)}read-onlycurrent
cm1110CopperAutoSpeedDownshift
OBJECT-TYPE
This object identifies the status of the copper auto speed downshift feature. noDownshift indicates that an automatic downshift of the copper speed has not occurred.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.1.1.33INTEGER {noDownshift(0), downshift(1)}read-onlycurrent
cm1110ConfigTable
OBJECT-TYPE
Table of CM-1110 type media converter module's configuration type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2not-accessiblecurrent
cm1110ConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1not-accessiblecurrent
cm1110ConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-1110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.2SlotNumbernot-accessiblecurrent
cm1110ConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.3ContainerStatusread-writecurrent
cm1110ConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm1110ConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.5INTEGER {standard(0), smartLinkPassthrough(1)}read-writecurrent
cm1110ConfigFiberFaultAlert
OBJECT-TYPE
This object identifies the Fiber Fault Alert setting for the media module. For 100 Mbps SFP modules, this setting is always effectively enabled if Link Mode is set to smartLinkPassthrough. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.6EnableDisableValueread-writecurrent
cm1110ConfigMaxPacketsSize
OBJECT-TYPE
This object identifies the media converter module's maximum packet size setting This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.7INTEGER {maxPacket1522(0), maxPacket2048(1), maxPacket10240(2)}read-writecurrent
cm1110ConfigFiberPortName
OBJECT-TYPE
This object identifies a user definable name for the fiber port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.8DisplayString (SIZE(0..8))read-writecurrent
cm1110ConfigFiberPortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.9YesNoValueread-writecurrent
cm1110ConfigFiberAutoNegotiation
OBJECT-TYPE
This object identifies whether fiber auto-negotiation is enabled. This object does not apply if the fiber connector type is a 100 Mbps SFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.10EnableDisableValueread-writecurrent
cm1110ConfigFiberSfp100duplex
OBJECT-TYPE
If the fiber connector type is SFP and it is a 100 Mbps fiber module then this object identifies the duplex setting for the 100 Mbps fiber port. Duplex for 1000 Mbps has to be auto negotiated. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.11INTEGER {full(0), half(1)}read-writecurrent
cm1110ConfigCopperPortName
OBJECT-TYPE
This object identifies a user definable name for the copper port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.12DisplayString (SIZE(0..8))read-writecurrent
cm1110ConfigCopperPortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.13YesNoValueread-writecurrent
cm1110ConfigCopperAutoNegotiation
OBJECT-TYPE
This object identifies the whether copper auto-negotiation is enabled. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.14EnableDisableValueread-writecurrent
cm1110ConfigCopperAutoNegAdv10HDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 10Mbps, half duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.15YesNoValueread-writecurrent
cm1110ConfigCopperAutoNegAdv10FDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 10Mbps, full duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.16YesNoValueread-writecurrent
cm1110ConfigCopperAutoNegAdv100HDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 100Mbps, half duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.17YesNoValueread-writecurrent
cm1110ConfigCopperAutoNegAdv100FDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 100Mbps, full duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.18YesNoValueread-writecurrent
cm1110ConfigCopperAutoNegAdv1000FDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 1000Mbps, full duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.19YesNoValueread-writecurrent
cm1110ConfigCopperSpeed
OBJECT-TYPE
If copper auto-negotiation is disabled then this object identifies the configured cooper speed. 1000 Mbps speed can only be auto negotiated. If copper auto-negotiation is enabled then this object is ignored. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.20INTEGER {speed10Mbs(0), speed100Mbps(1)}read-writecurrent
cm1110ConfigCopperDuplex
OBJECT-TYPE
If copper auto-negotiation is disabled then this object identifies the duplex setting for 10 & 100 Mbps for the copper port. Duplex for 1000 Mbps has to be auto negotiated. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.21INTEGER {full(0), half(1)}read-writecurrent
cm1110ConfigCopperCrossOver
OBJECT-TYPE
This object identifies the copper MDI/MDI-X setting.This object is read-only if the media converter module's ConfigMode jumper is set to
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.22INTEGER {auto(0), mdi(1), mdix(2)}read-writecurrent
cm1110ConfigCopperPauseEnh
OBJECT-TYPE
This object identifies the copper pause (flow control) setting that is a advertised. The settings can be disabled, advertise symmetrical, advertise asymmetrical TX or advertise symmetrical and asymmetrical RX. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.23INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), symmAsymRx(3)}read-writecurrent
cm1110ConfigCopperAutoSpeedDownshift
OBJECT-TYPE
This object identifies the number of times the PHY attempts to establish a Gigabit link before the PHY downshift to the next highest speed. A value of 0 indicates the auto downshift is disabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.24INTEGER (0..8)read-writecurrent
cm1110ConfigCopper10BaseTDistance
OBJECT-TYPE
When using cable exceeding 100 meters in 10BASE-T mode this feature should be set to extended(1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.25INTEGER {normal(0), extended(1)}read-writecurrent
cm1110ConfigUnidirectionalEthernet
OBJECT-TYPE
Restrict the flow of Ethernet traffic to a single direction. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.26INTEGER {notApplicable(-1), disabled(0), copperToFiber(1), fiberToCopper(2)}read-writecurrent
cm1110ConfigPriorityToEgressQueueMap0
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.27INTEGER (0..3)read-writecurrent
cm1110ConfigPriorityToEgressQueueMap1
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.28INTEGER (0..3)read-writecurrent
cm1110ConfigPriorityToEgressQueueMap2
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.29INTEGER (0..3)read-writecurrent
cm1110ConfigPriorityToEgressQueueMap3
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.30INTEGER (0..3)read-writecurrent
cm1110ConfigPriorityToEgressQueueMap4
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.31INTEGER (0..3)read-writecurrent
cm1110ConfigPriorityToEgressQueueMap5
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.32INTEGER (0..3)read-writecurrent
cm1110ConfigPriorityToEgressQueueMap6
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.33INTEGER (0..3)read-writecurrent
cm1110ConfigPriorityToEgressQueueMap7
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.34INTEGER (0..3)read-writecurrent
cm1110ConfigCopper8021pPriority
OBJECT-TYPE
Use 802.1p tag priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.35OnOffValueread-writecurrent
cm1110ConfigCopperIpTosPriority
OBJECT-TYPE
Use IP TOS priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.36OnOffValueread-writecurrent
cm1110ConfigCopperPriorityPrecedence
OBJECT-TYPE
Configure priority precedence. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.37INTEGER {notApplicable(-1), priority8021p(0), priorityIpTos(1)}read-writecurrent
cm1110ConfigCopperCongestionPolicy
OBJECT-TYPE
Configure priority congestion policy. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.38INTEGER {notApplicable(-1), strict(0), weighted(1)}read-writecurrent
cm1110ConfigCopperPriorityMap0
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.39INTEGER (0..7)read-writecurrent
cm1110ConfigCopperPriorityMap1
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.40INTEGER (0..7)read-writecurrent
cm1110ConfigCopperPriorityMap2
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.41INTEGER (0..7)read-writecurrent
cm1110ConfigCopperPriorityMap3
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.42INTEGER (0..7)read-writecurrent
cm1110ConfigCopperPriorityMap4
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.43INTEGER (0..7)read-writecurrent
cm1110ConfigCopperPriorityMap5
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.44INTEGER (0..7)read-writecurrent
cm1110ConfigCopperPriorityMap6
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.45INTEGER (0..7)read-writecurrent
cm1110ConfigCopperPriorityMap7
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.46INTEGER (0..7)read-writecurrent
cm1110ConfigCopperIngressLimit
OBJECT-TYPE
Set a limit on the rate of incoming packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.47INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26), rate100mbps(27), rate200mbps(28), rate300mbps(29), rate400mbps(30), rate500mbps(31), rate600mbps(32), rate700mbps(33), rate800mbps(34), rate900mbps(35)}read-writecurrent
cm1110ConfigCopperEgressLimit
OBJECT-TYPE
Set a limit on the rate of outgoing packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.48INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26), rate100mbps(27), rate200mbps(28), rate300mbps(29), rate400mbps(30), rate500mbps(31), rate600mbps(32), rate700mbps(33), rate800mbps(34), rate900mbps(35)}read-writecurrent
cm1110ConfigCopperDiscardTaggedFrames
OBJECT-TYPE
Enable discarding of tagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.49OnOffValueread-writecurrent
cm1110ConfigCopperDiscardUntaggedFrames
OBJECT-TYPE
Enable discarding of untagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.50OnOffValueread-writecurrent
cm1110ConfigCopperDefaultVlanId
OBJECT-TYPE
Set the default VLAN ID to insert when tagging frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.51INTEGER (0..4095)read-writecurrent
cm1110ConfigCopperDefaultPriority
OBJECT-TYPE
Set the default frame priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.52INTEGER (0..7)read-writecurrent
cm1110ConfigCopperVlanTaggingAction
OBJECT-TYPE
Set the default tagging action. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.53INTEGER {notApplicable(-1), none(0), untag(1), tag(2), doubleTag(3)}read-writecurrent
cm1110ConfigCopperFilterUnknownMulticast
OBJECT-TYPE
Enable filtering of multicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.54OnOffValueread-writecurrent
cm1110ConfigCopperFilterUnknownUnicast
OBJECT-TYPE
Enable filtering of unicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.55OnOffValueread-writecurrent
cm1110ConfigFiber8021pPriority
OBJECT-TYPE
Use 802.1p tag priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.56OnOffValueread-writecurrent
cm1110ConfigFiberIpTosPriority
OBJECT-TYPE
Use IP TOS priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.57OnOffValueread-writecurrent
cm1110ConfigFiberPriorityPrecedence
OBJECT-TYPE
Configure priority precedence. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.58INTEGER {notApplicable(-1), priority8021p(0), priorityIpTos(1)}read-writecurrent
cm1110ConfigFiberCongestionPolicy
OBJECT-TYPE
Configure priority congestion policy. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.59INTEGER {notApplicable(-1), strict(0), weighted(1)}read-writecurrent
cm1110ConfigFiberPriorityMap0
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.60INTEGER (0..7)read-writecurrent
cm1110ConfigFiberPriorityMap1
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.61INTEGER (0..7)read-writecurrent
cm1110ConfigFiberPriorityMap2
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.62INTEGER (0..7)read-writecurrent
cm1110ConfigFiberPriorityMap3
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.63INTEGER (0..7)read-writecurrent
cm1110ConfigFiberPriorityMap4
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.64INTEGER (0..7)read-writecurrent
cm1110ConfigFiberPriorityMap5
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.65INTEGER (0..7)read-writecurrent
cm1110ConfigFiberPriorityMap6
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.66INTEGER (0..7)read-writecurrent
cm1110ConfigFiberPriorityMap7
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.67INTEGER (0..7)read-writecurrent
cm1110ConfigFiberIngressLimit
OBJECT-TYPE
Set a limit on the rate of incoming packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.68INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26), rate100mbps(27), rate200mbps(28), rate300mbps(29), rate400mbps(30), rate500mbps(31), rate600mbps(32), rate700mbps(33), rate800mbps(34), rate900mbps(35)}read-writecurrent
cm1110ConfigFiberEgressLimit
OBJECT-TYPE
Set a limit on the rate of outgoing packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.69INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26), rate100mbps(27), rate200mbps(28), rate300mbps(29), rate400mbps(30), rate500mbps(31), rate600mbps(32), rate700mbps(33), rate800mbps(34), rate900mbps(35)}read-writecurrent
cm1110ConfigFiberDiscardTaggedFrames
OBJECT-TYPE
Enable discarding of tagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.70OnOffValueread-writecurrent
cm1110ConfigFiberDiscardUntaggedFrames
OBJECT-TYPE
Enable discarding of untagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.71OnOffValueread-writecurrent
cm1110ConfigFiberDefaultVlanId
OBJECT-TYPE
Set the default VLAN ID to insert when tagging frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.72INTEGER (0..4095)read-writecurrent
cm1110ConfigFiberDefaultPriority
OBJECT-TYPE
Set the default frame priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.73INTEGER (0..7)read-writecurrent
cm1110ConfigFiberVlanTaggingAction
OBJECT-TYPE
Set the default tagging action. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.74INTEGER {notApplicable(-1), none(0), untag(1), tag(2), doubleTag(3)}read-writecurrent
cm1110ConfigFiberFilterUnknownMulticast
OBJECT-TYPE
Enable filtering of multicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.75OnOffValueread-writecurrent
cm1110ConfigFiberFilterUnknownUnicast
OBJECT-TYPE
Enable filtering of unicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.76OnOffValueread-writecurrent
cm1110ConfigFiberSgmiiInterface
OBJECT-TYPE
This object identifies whether fiber SGMII interface is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.2.1.77EnableDisableValueread-writecurrent
cm1110LedTable
OBJECT-TYPE
Table of CM-1110 type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3not-accessiblecurrent
cm1110LedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3.1not-accessiblecurrent
cm1110LedSlotIndex
OBJECT-TYPE
The Slot number the CM-1110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3.1.2SlotNumbernot-accessiblecurrent
cm1110LedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Fiber loopback enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm1110LedFDF
OBJECT-TYPE
This object identifies the status of the Full Duplex Fiber (FDF) LED on the media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3.1.4INTEGER {offHalfDuplex(0), onFullDuplex(1)}read-onlycurrent
cm1110LedLKF
OBJECT-TYPE
This object identifies the status of the link fiber (LKF) LED on the media converter module. Possible status values are: off(0) - No fiber link on(1) - Fiber link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
cm1110LedCopperSpeed
OBJECT-TYPE
This object identifies the status of the link copper speed (100/1000) LED on the management module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3.1.6INTEGER {off10Mbps(0), onYellow100Mbps(1), onGreen1000Mbps(2)}read-onlycurrent
cm1110LedFDC
OBJECT-TYPE
This object identifies the status of the Full Duplex Copper (FDC) LED on the media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3.1.7INTEGER {offHalfDuplex(0), onFullDuplex(1)}read-onlycurrent
cm1110LedLKC
OBJECT-TYPE
This object identifies the status of the link copper (LKC) LED on the media converter module. Possible status values are: off(0) - No copper link on(1) - Copper link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.3.1.8INTEGER {off(0), on(1)}read-onlycurrent
cm1110RateConvStatsTable
OBJECT-TYPE
Table of CM-1110 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4not-accessiblecurrent
cm1110RateConvStatsEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1not-accessiblecurrent
cm1110StatsSlotIndex
OBJECT-TYPE
The Slot number the CM-1110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.2SlotNumbernot-accessiblecurrent
cm1110MediaPortIndex
OBJECT-TYPE
Media converter module port index indicating which media port the statistical counters are associated with.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.3INTEGER {copper(1), fiber(2)}not-accessiblecurrent
cm1110PortInDiscards
OBJECT-TYPE
A counter that counts the number of good, non-filtered frames that normally would have been forwarded, but could not due to lack of buffer space.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.4Counter32read-onlycurrent
cm1110PortInFiltered
OBJECT-TYPE
A counter that counts the number of good frames that were filtered due to ingress switch policy rules.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.5INTEGER (0..65535)read-onlycurrent
cm1110PortInGoodOctets
OBJECT-TYPE
An ingress counter that is the sum of lengths of all good Ethernet frames received on the media port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.6Counter32read-onlycurrent
cm1110PortHCInGoodOctets
OBJECT-TYPE
An ingress counter that is the sum of lengths of all good Ethernet frames received on the media port. This object is a 64-bit version of cm1110PortInGoodOctets.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.7Counter64read-onlycurrent
cm1110PortInBadOctets
OBJECT-TYPE
An ingress counter that is the sum of lengths of all bad Ethernet frames received on the media port..
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.8Counter32read-onlycurrent
cm1110PortInUnicasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Unicast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.9Counter32read-onlycurrent
cm1110PortInBroadcasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Broadcast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.10Counter32read-onlycurrent
cm1110PortInMulticasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Multicast destination MAC address. This count does not include frames counted in the cm1110PortInPauses or the cm1110PortInBroadcasts objects.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.11Counter32read-onlycurrent
cm1110PortInPauses
OBJECT-TYPE
An ingress counter that counts the number of good frames reachieved that have a Pause destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.12Counter32read-onlycurrent
cm1110PortInUnderSizes
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length less that 64 octets but with a valid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.13Counter32read-onlycurrent
cm1110PortInFragments
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length less that 64 octets and an invalid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.14Counter32read-onlycurrent
cm1110PortInOversizes
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length more than the maximum packet size but with a valid FCS. The maximum packet size can be set using the cm1110ConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.15Counter32read-onlycurrent
cm1110PortInJabbers
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length more than the maximum packet size but with a invalid FCS. The maximum packet size can be set using the cm1110ConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.16Counter32read-onlycurrent
cm1110PortInRxErrs
OBJECT-TYPE
An ingress counter that counts the number of frames received with an RxErr signal from the PHY.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.17Counter32read-onlycurrent
cm1110PortInFcsErrs
OBJECT-TYPE
An ingress counter that counts the number of frames received with a CRC error not counted in the cm1110PortInFragments, cm1110PortInFcsErr, or the cm1110PortInRxErr objects.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.18Counter32read-onlycurrent
cm1110PortPkts64Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of exactly 64 Octets, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.19Counter32read-onlycurrent
cm1110PortPkts65to127Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 65 and 127 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.20Counter32read-onlycurrent
cm1110PortPkts128to255Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 128 and 255 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.21Counter32read-onlycurrent
cm1110PortPkts256to511Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 256 and 511 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.22Counter32read-onlycurrent
cm1110PortPkts512to1023Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 512 and 1023 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.23Counter32read-onlycurrent
cm1110PortPkts1024toMaxOctets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 1024 and maximum packet size octets inclusive, including those with errors. The maximum packet size can be set using the cm1110ConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.24Counter32read-onlycurrent
cm1110PortOutOctets
OBJECT-TYPE
An Egress counter that is the sum of lengths of all good Ethernet frames sent on the media port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.25Counter32read-onlycurrent
cm1110PortHCOutOctets
OBJECT-TYPE
An Egress counter that is the sum of lengths of all good Ethernet frames sent on the media port. This object is a 64-bit version of cm1110PortOutOctets.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.26Counter64read-onlycurrent
cm1110PortOutFiltered
OBJECT-TYPE
A counter that counts the number of good frames that were filtered due to egress switch policy rules.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.27INTEGER (0..65535)read-onlycurrent
cm1110PortOutUnicasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Unicast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.28Counter32read-onlycurrent
cm1110PortOutBroadcasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Broadcast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.29Counter32read-onlycurrent
cm1110PortOutMulticasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Multicast destination MAC address. This count does not include frames counted in the cm1110PortOutPauses or the cm1110PortOutBroadcasts objects.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.30Counter32read-onlycurrent
cm1110PortOutPauses
OBJECT-TYPE
An Egress counter that counts the number of good frames reachieved that have a Pause destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.31Counter32read-onlycurrent
cm1110PortDeferreds
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced no collisions but are delayed because the medium was busy during the first attempt. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.32Counter32read-onlycurrent
cm1110PortCollisions
OBJECT-TYPE
An Egress counter that counts the number of collision events seen by the MAC not including those counted in cm1110PortSingles, cm1110PortMultiple , cm1110PortExcessives or cm1110PortLates objects. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.33Counter32read-onlycurrent
cm1110PortSingles
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced exactly one collision. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.34Counter32read-onlycurrent
cm1110PortMultiples
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced more than one collision. This counter is aplicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.35Counter32read-onlycurrent
cm1110PortExcessives
OBJECT-TYPE
An Egress counter that counts the number frames dropped in the transmit MAC because the frame experienced 16 consecutive collisions. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.36Counter32read-onlycurrent
cm1110PortLates
OBJECT-TYPE
An Egress counter that counts the number times a collision is detected later than 512 bits-times into the transmission of a frame. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.37Counter32read-onlycurrent
cm1110PortOutFcsErrs
OBJECT-TYPE
An Egress counter that counts the number frames transmitted with an invalid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.38Counter32read-onlycurrent
cm1110PortResetCounters
OBJECT-TYPE
Allows the resetting of all cm1110RateConvStats statistical counters for this port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.4.1.39YesNoValueread-writecurrent
cm1110RateConvAvctTable
OBJECT-TYPE
Table of CM-1110 type media converter module's
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5not-accessiblecurrent
cm1110RateConvAvctEntry
OBJECT-TYPE
Entries of the table, each relating to a separate fiber or copper port on the CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1not-accessiblecurrent
cm1110AvctSlotIndex
OBJECT-TYPE
The Slot number the CM-1110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.2SlotNumbernot-accessiblecurrent
cm1110AvctStart
OBJECT-TYPE
Set this self-clearing variable to yes initiate the Advanced Virtual Cable Test. Note: During the test, no network data will be passed.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.3YesNoValueread-writecurrent
cm1110AvctStatus
OBJECT-TYPE
This object identifies the state of the Advanced Virtual Cable Tester.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.4INTEGER {notStarted(0), inProgress(1), testComplete(2)}read-onlycurrent
cm1110AvctTxRxPair1Results
OBJECT-TYPE
Test result code returned from Virtual Cable Test of the Tx/Rx pair one.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.5INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
cm1110AvctTxRxPair1Amplitude
OBJECT-TYPE
Amplitude of Tx/Rx pair one in millivolts when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.6DisplayString (SIZE(0..20))read-onlycurrent
cm1110AvctTxRxPair1Distance
OBJECT-TYPE
Distance in meters to fault when test result codes for Tx/Rx pair one is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.7DisplayString (SIZE(0..20))read-onlycurrent
cm1110AvctTxRxPair2Results
OBJECT-TYPE
Test result code returned from Virtual Cable Test of the Tx/Rx pair two.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.8INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
cm1110AvctTxRxPair2Amplitude
OBJECT-TYPE
Amplitude of Tx/Rx pair two in millivolts when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.9DisplayString (SIZE(0..20))read-onlycurrent
cm1110AvctTxRxPair2Distance
OBJECT-TYPE
Distance in meters to fault when test result codes for Tx/Rx pair two is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.10DisplayString (SIZE(0..20))read-onlycurrent
cm1110AvctTxRxPair3Results
OBJECT-TYPE
Test result code returned from Virtual Cable Test of the Tx/Rx pair three.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.11INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
cm1110AvctTxRxPair3Amplitude
OBJECT-TYPE
Amplitude of Tx/Rx pair three in millivolts when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.12DisplayString (SIZE(0..20))read-onlycurrent
cm1110AvctTxRxPair3Distance
OBJECT-TYPE
Distance in meters to fault when test result codes for Tx/Rx pair three is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.13DisplayString (SIZE(0..20))read-onlycurrent
cm1110AvctTxRxPair4Results
OBJECT-TYPE
Test result code returned from Virtual Cable Test of Tx/Rx pair four.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.14INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
cm1110AvctTxRxPair4Amplitude
OBJECT-TYPE
Amplitude of Tx/Rx pair four in millivolts when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.15DisplayString (SIZE(0..20))read-onlycurrent
cm1110AvctTxRxPair4Distance
OBJECT-TYPE
Distance in meters to fault when test result codes for Tx/Rx pair four is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.3.5.1.16DisplayString (SIZE(0..20))read-onlycurrent
cm110RateConv
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.4
cm110RateConvTable
OBJECT-TYPE
Table of CM-110 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1not-accessiblecurrent
cm110RateConvEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1not-accessiblecurrent
cm110SlotIndex
OBJECT-TYPE
The Slot number the CM-110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.2SlotNumbernot-accessiblecurrent
cm110Modelname
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.3DisplayStringread-onlycurrent
cm110ModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.4DisplayStringread-onlycurrent
cm110HwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware switch on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm110HwJmp6AutoMDIX
OBJECT-TYPE
This object identifies the media converter module's hardware Auto MDIX jumper settings.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.6INTEGER {mdix(0), auto(1)}read-onlycurrent
cm110HwSw1TpAutoNegotiation
OBJECT-TYPE
Media converter module's current switch setting for copper auto-negotiation.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.7INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm110HwSw2LinkMode
OBJECT-TYPE
Media converter module's current switch setting for Link Mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.8INTEGER {swDownNormalMode(0), swUpSmartLinkPassthroughMode(1)}read-onlycurrent
cm110HwSw3FarEndFault
OBJECT-TYPE
Media converter module's current switch setting for Far End Fault.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.9INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm110HwSw4TpDuplex
OBJECT-TYPE
Media converter module's current switch setting for copper duplex.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.10INTEGER {swDownHalf(0), swUpFull(1)}read-onlycurrent
cm110HwSw5TpSpeed
OBJECT-TYPE
Media converter module's current switch setting for Link Mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.11INTEGER {swDown10Mbps(0), swUp100Mbps(1)}read-onlycurrent
cm110HwSw6FiberDuplex
OBJECT-TYPE
Media converter module's current switch setting for fiber duplex.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.12INTEGER {swDownHalf(0), swUpFull(1)}read-onlycurrent
cm110HwSw7Loopback
OBJECT-TYPE
Media converter module's current switch setting for fiber loopback mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.13INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
cm110FiberLinkStatus
OBJECT-TYPE
Media converter module's current fiber link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.14INTEGER {down(0), up(1)}read-onlycurrent
cm110FiberConnType
OBJECT-TYPE
Media converter module's fiber port connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.15INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6)}read-onlycurrent
cm110FiberSpeed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.16INTEGER {speed100Mbps(1)}read-onlycurrent
cm110FiberFarEndFault
OBJECT-TYPE
Media converter module's current fiber Far End Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.17INTEGER {disable(0), ok(1), receivingFEF(2), sendingFEF(3)}read-onlycurrent
cm110FiberReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.18INTEGER {fault(0), ok(1)}read-writecurrent
cm110FiberLoopBack
OBJECT-TYPE
This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.19EnableDisableValueread-writecurrent
cm110CopperLinkStatus
OBJECT-TYPE
Media converter module's current copper link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.20INTEGER {down(0), up(1)}read-onlycurrent
cm110CopperConnType
OBJECT-TYPE
Media converter module's copper connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.21INTEGER {rj45(0)}read-onlycurrent
cm110CopperAutoNegState
OBJECT-TYPE
Media converter module's current copper auto-negotiation state.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.22INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm110CopperSpeed
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated speed setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.23INTEGER {speed10Mbs(0), speed100Mbps(1)}read-onlycurrent
cm110CopperDuplex
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.24INTEGER {half(0), full(1)}read-onlycurrent
cm110CopperCrossOver
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated MDI/MDI-X setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.25INTEGER {mdi(0), mdix(1)}read-onlycurrent
cm110CopperPause
OBJECT-TYPE
If copper auto-negotiation state is complete then this object indicates the media converter module's current copper auto-negotiated pause (flow control) setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.26INTEGER {disabled(0), symmetrical(1)}read-onlycurrent
cm110CopperLPRFStatus
OBJECT-TYPE
Media converter module's fiber Link Partner Remote Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.1.1.27INTEGER {ok(0), remoteFault(1)}read-onlycurrent
cm110ConfigTable
OBJECT-TYPE
Table of CM-110 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2not-accessiblecurrent
cm110ConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1not-accessiblecurrent
cm110ConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.2SlotNumbernot-accessiblecurrent
cm110ConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.3ContainerStatusread-writecurrent
cm110ConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm110ConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.5INTEGER {standard(0), linkPassthrough(1)}read-writecurrent
cm110ConfigFiberFarEndFault
OBJECT-TYPE
This object identifies the Fiber Fault Alert setting for the media module. This setting is always enabled if Link Mode is set to linkPassthrough. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.6INTEGER {disable(0), enable(1)}read-writecurrent
cm110ConfigMaxPacketSize
OBJECT-TYPE
This object identifies the media converter module's maximum packet size setting This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.7INTEGER {maxpacket1522(0), maxpacket2048(1)}read-writecurrent
cm110ConfigFiberPortName
OBJECT-TYPE
This object identifies a user definable name for the fiber port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.8DisplayString (SIZE(0..8))read-writecurrent
cm110ConfigFiberPortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.9YesNoValueread-writecurrent
cm110ConfigFiberDuplex
OBJECT-TYPE
This object identifies the fiber port duplex setting.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.10INTEGER {full(0), half(1)}read-onlycurrent
cm110ConfigCopperPortName
OBJECT-TYPE
This object identifies a user definable name for the copper port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.11DisplayString (SIZE(0..8))read-writecurrent
cm110ConfigCopperPortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.12YesNoValueread-writecurrent
cm110ConfigCopperAutoNegotiation
OBJECT-TYPE
This object identifies the whether copper auto-negotiation is enabled. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.13INTEGER {disable(0), enable(1)}read-writecurrent
cm110ConfigCopperAutoNegAdv10HDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 10Mbps, half duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.14YesNoValueread-writecurrent
cm110ConfigCopperAutoNegAdv10FDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 10Mbps, full duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.15YesNoValueread-writecurrent
cm110ConfigCopperAutoNegAdv100HDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 100Mbps, half duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.16YesNoValueread-writecurrent
cm110ConfigCopperAutoNegAdv100FDX
OBJECT-TYPE
This object controls whether or the copper port advertises willingness to connect at 100Mbps, full duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.17YesNoValueread-writecurrent
cm110ConfigCopperSpeed
OBJECT-TYPE
This object identifies the current copper speed in megabits per second. This object is ignored if auto-negotiation is enabled. This object is ignored if auto-negotiation is enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.18INTEGER {speed10Mbs(0), speed100Mbps(1)}read-writecurrent
cm110ConfigCopperDuplex
OBJECT-TYPE
This object identifies the copper duplex setting. This object is ignored if auto-negotiation is enabled This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.19INTEGER {full(0), half(1)}read-writecurrent
cm110ConfigCopperCrossOver
OBJECT-TYPE
This object identifies the copper MDI/MDI-X setting.This object is read-only if the media converter module's ConfigMode jumper is set to
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.20INTEGER {auto(0), mdi(1), mdix(2)}read-writecurrent
cm110ConfigCopperPause
OBJECT-TYPE
This object identifies the copper's pause (flow control) settings. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.21INTEGER {disabled(0), enable(1)}read-writecurrent
cm110ConfigCopperExtendDistance
OBJECT-TYPE
When using cable exceeding 100 meters, the 10BASE-T this feature should be enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.22EnableDisableValueread-writecurrent
cm110ConfigUnidirectionalEthernet
OBJECT-TYPE
Restrict the flow of Ethernet traffic to a single direction. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.23INTEGER {notApplicable(-1), disabled(0), copperToFiber(1), fiberToCopper(2)}read-writecurrent
cm110ConfigPriorityToEgressQueueMap0
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.24INTEGER (0..3)read-writecurrent
cm110ConfigPriorityToEgressQueueMap1
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.25INTEGER (0..3)read-writecurrent
cm110ConfigPriorityToEgressQueueMap2
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.26INTEGER (0..3)read-writecurrent
cm110ConfigPriorityToEgressQueueMap3
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.27INTEGER (0..3)read-writecurrent
cm110ConfigPriorityToEgressQueueMap4
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.28INTEGER (0..3)read-writecurrent
cm110ConfigPriorityToEgressQueueMap5
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.29INTEGER (0..3)read-writecurrent
cm110ConfigPriorityToEgressQueueMap6
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.30INTEGER (0..3)read-writecurrent
cm110ConfigPriorityToEgressQueueMap7
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.31INTEGER (0..3)read-writecurrent
cm110ConfigCopper8021pPriority
OBJECT-TYPE
Use 802.1p tag priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.32OnOffValueread-writecurrent
cm110ConfigCopperIpTosPriority
OBJECT-TYPE
Use IP TOS priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.33OnOffValueread-writecurrent
cm110ConfigCopperPriorityPrecedence
OBJECT-TYPE
Configure priority precedence. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.34INTEGER {notApplicable(-1), priority8021p(0), priorityIpTos(1)}read-writecurrent
cm110ConfigCopperCongestionPolicy
OBJECT-TYPE
Configure priority congestion policy. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.35INTEGER {notApplicable(-1), strict(0), weighted(1)}read-writecurrent
cm110ConfigCopperPriorityMap0
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.36INTEGER (0..7)read-writecurrent
cm110ConfigCopperPriorityMap1
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.37INTEGER (0..7)read-writecurrent
cm110ConfigCopperPriorityMap2
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.38INTEGER (0..7)read-writecurrent
cm110ConfigCopperPriorityMap3
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.39INTEGER (0..7)read-writecurrent
cm110ConfigCopperPriorityMap4
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.40INTEGER (0..7)read-writecurrent
cm110ConfigCopperPriorityMap5
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.41INTEGER (0..7)read-writecurrent
cm110ConfigCopperPriorityMap6
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.42INTEGER (0..7)read-writecurrent
cm110ConfigCopperPriorityMap7
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.43INTEGER (0..7)read-writecurrent
cm110ConfigCopperIngressLimit
OBJECT-TYPE
Set a limit on the rate of incoming packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.44INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26)}read-writecurrent
cm110ConfigCopperEgressLimit
OBJECT-TYPE
Set a limit on the rate of outgoing packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.45INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26)}read-writecurrent
cm110ConfigCopperDiscardTaggedFrames
OBJECT-TYPE
Enable discarding of tagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.46OnOffValueread-writecurrent
cm110ConfigCopperDiscardUntaggedFrames
OBJECT-TYPE
Enable discarding of untagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.47OnOffValueread-writecurrent
cm110ConfigCopperDefaultVlanId
OBJECT-TYPE
Set the default VLAN ID to insert when tagging frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.48INTEGER (0..4095)read-writecurrent
cm110ConfigCopperDefaultPriority
OBJECT-TYPE
Set the default frame priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.49INTEGER (0..7)read-writecurrent
cm110ConfigCopperVlanTaggingAction
OBJECT-TYPE
Set the default tagging action. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.50INTEGER {notApplicable(-1), none(0), untag(1), tag(2), doubleTag(3)}read-writecurrent
cm110ConfigCopperFilterUnknownMulticast
OBJECT-TYPE
Enable filtering of multicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.51OnOffValueread-writecurrent
cm110ConfigCopperFilterUnknownUnicast
OBJECT-TYPE
Enable filtering of unicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.52OnOffValueread-writecurrent
cm110ConfigFiber8021pPriority
OBJECT-TYPE
Use 802.1p tag priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.53OnOffValueread-writecurrent
cm110ConfigFiberIpTosPriority
OBJECT-TYPE
Use IP TOS priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.54OnOffValueread-writecurrent
cm110ConfigFiberPriorityPrecedence
OBJECT-TYPE
Configure priority precedence. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.55INTEGER {notApplicable(-1), priority8021p(0), priorityIpTos(1)}read-writecurrent
cm110ConfigFiberCongestionPolicy
OBJECT-TYPE
Configure priority congestion policy. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.56INTEGER {notApplicable(-1), strict(0), weighted(1)}read-writecurrent
cm110ConfigFiberPriorityMap0
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.57INTEGER (0..7)read-writecurrent
cm110ConfigFiberPriorityMap1
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.58INTEGER (0..7)read-writecurrent
cm110ConfigFiberPriorityMap2
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.59INTEGER (0..7)read-writecurrent
cm110ConfigFiberPriorityMap3
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.60INTEGER (0..7)read-writecurrent
cm110ConfigFiberPriorityMap4
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.61INTEGER (0..7)read-writecurrent
cm110ConfigFiberPriorityMap5
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.62INTEGER (0..7)read-writecurrent
cm110ConfigFiberPriorityMap6
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.63INTEGER (0..7)read-writecurrent
cm110ConfigFiberPriorityMap7
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.64INTEGER (0..7)read-writecurrent
cm110ConfigFiberIngressLimit
OBJECT-TYPE
Set a limit on the rate of incoming packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.65INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26)}read-writecurrent
cm110ConfigFiberEgressLimit
OBJECT-TYPE
Set a limit on the rate of outgoing packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.66INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26)}read-writecurrent
cm110ConfigFiberDiscardTaggedFrames
OBJECT-TYPE
Enable discarding of tagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.67OnOffValueread-writecurrent
cm110ConfigFiberDiscardUntaggedFrames
OBJECT-TYPE
Enable discarding of untagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.68OnOffValueread-writecurrent
cm110ConfigFiberDefaultVlanId
OBJECT-TYPE
Set the default VLAN ID to insert when tagging frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.69INTEGER (0..4095)read-writecurrent
cm110ConfigFiberDefaultPriority
OBJECT-TYPE
Set the default frame priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.70INTEGER (0..7)read-writecurrent
cm110ConfigFiberVlanTaggingAction
OBJECT-TYPE
Set the default tagging action. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.71INTEGER {notApplicable(-1), none(0), untag(1), tag(2), doubleTag(3)}read-writecurrent
cm110ConfigFiberFilterUnknownMulticast
OBJECT-TYPE
Enable filtering of multicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.72OnOffValueread-writecurrent
cm110ConfigFiberFilterUnknownUnicast
OBJECT-TYPE
Enable filtering of unicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.2.1.73OnOffValueread-writecurrent
cm110LedTable
OBJECT-TYPE
Table of CM-110 type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3not-accessiblecurrent
cm110LedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3.1not-accessiblecurrent
cm110LedSlotIndex
OBJECT-TYPE
The Slot number the CM-110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3.1.2SlotNumbernot-accessiblecurrent
cm110LedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Fiber loopback enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm110LedFDF
OBJECT-TYPE
This object identifies the status of the Full Duplex Fiber (FDF) LED on the media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3.1.4INTEGER {offHalfDuplex(0), onFullDuplex(1)}read-onlycurrent
cm110LedLKF
OBJECT-TYPE
This object identifies the status of the link fiber (LKF) LED on the media converter module. Possible status values are: off(0) - No fiber link on(1) - Fiber link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
cm110LedCopperSpeed
OBJECT-TYPE
This object identifies the status of the link copper speed (100/1000) LED on the media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3.1.6INTEGER {off10Mbps(0), onGreen100Mbps(1)}read-onlycurrent
cm110LedFDC
OBJECT-TYPE
This object identifies the status of the Full Duplex Copper (FDC) LED on the media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3.1.7INTEGER {offHalfDuplex(0), onFullDuplex(1)}read-onlycurrent
cm110LedLKC
OBJECT-TYPE
This object identifies the status of the link copper (LKC) LED on the media converter module. Possible status values are: off(0) - No copper link on(1) - Copper link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.3.1.8INTEGER {off(0), on(1)}read-onlycurrent
cm110RateConvStatsTable
OBJECT-TYPE
Table of CM-110 media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4not-accessiblecurrent
cm110RateConvStatsEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1not-accessiblecurrent
cm110StatsSlotIndex
OBJECT-TYPE
The Slot number the CM-110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.2SlotNumbernot-accessiblecurrent
cm110MediaPortIndex
OBJECT-TYPE
Media converter module port index indicating which media port the statistical counters are associated with.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.3INTEGER {copper(1), fiber(2)}not-accessiblecurrent
cm110PortRxErrors
OBJECT-TYPE
Total number of bad frames received.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.4INTEGER (0..65535)read-onlycurrent
cm110PortTxCollisions
OBJECT-TYPE
Total number of TX collisions encountered.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.5INTEGER (0..65535)read-onlycurrent
cm110PortInFiltered
OBJECT-TYPE
A counter that counts the number of good frames that were filtered due to ingress switch policy rules.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.6INTEGER (0..65535)read-onlycurrent
cm110PortInGoodOctets
OBJECT-TYPE
An ingress counter that is the sum of lengths of all good Ethernet frames received on the media port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.7Counter32read-onlycurrent
cm110PortInBadOctets
OBJECT-TYPE
An ingress counter that is the sum of lengths of all bad Ethernet frames received on the media port..
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.8Counter32read-onlycurrent
cm110PortInUnicasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Unicast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.9Counter32read-onlycurrent
cm110PortInBroadcasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Broadcast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.10Counter32read-onlycurrent
cm110PortInMulticasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Multicast destination MAC address. This count does not include frames counted in the cm1110PortInPauses or the cm1110PortInBroadcasts objects.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.11Counter32read-onlycurrent
cm110PortInPauses
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Pause destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.12Counter32read-onlycurrent
cm110PortInUnderSizes
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length less that 64 octets but with a valid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.13Counter32read-onlycurrent
cm110PortInFragments
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length less that 64 octets and an invalid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.14Counter32read-onlycurrent
cm110PortInOversizes
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length more than the maximum packet size but with a valid FCS. The maximum packet size can be set using the cm110ConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.15Counter32read-onlycurrent
cm110PortInJabbers
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length more than the maximum packet size but with a invalid FCS. The maximum packet size can be set using the cm110ConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.16Counter32read-onlycurrent
cm110PortInMACRcvErrs
OBJECT-TYPE
An ingress counter of the number of Rx errors on the receive side of the MAC
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.17Counter32read-onlycurrent
cm110PortInFcsErrs
OBJECT-TYPE
An ingress counter of the number of FCS Errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.18Counter32read-onlycurrent
cm110PortPkts64Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of exactly 64 Octets, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.19Counter32read-onlycurrent
cm110PortPkts65to127Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 65 and 127 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.20Counter32read-onlycurrent
cm110PortPkts128to255Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 128 and 255 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.21Counter32read-onlycurrent
cm110PortPkts256to511Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 256 and 511 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.22Counter32read-onlycurrent
cm110PortPkts512to1023Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 512 and 1023 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.23Counter32read-onlycurrent
cm110PortPkts1024toMaxOctets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 1024 and maximum packet size octets inclusive, including those with errors. The maximum packet size can be set using the cm1110ConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.24Counter32read-onlycurrent
cm110PortOutOctets
OBJECT-TYPE
An Egress counter that is the sum of lengths of all good Ethernet frames sent on the media port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.25Counter32read-onlycurrent
cm110PortOutUnicasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Unicast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.26Counter32read-onlycurrent
cm110PortOutBroadcasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Broadcast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.27Counter32read-onlycurrent
cm110PortOutMulticasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Multicast destination MAC address. This count does not include frames counted in the cm1110PortOutPauses or the cm1110PortOutBroadcasts objects.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.28Counter32read-onlycurrent
cm110PortOutPauses
OBJECT-TYPE
An Egress counter that counts the number of good frames received that have a Pause destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.29Counter32read-onlycurrent
cm110PortDeferreds
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced no collsions but are delayed because the medium was busy during the first attempt. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.30Counter32read-onlycurrent
cm110PortCollisions
OBJECT-TYPE
An Egress counter that counts the number of collision events seen by the MAC not including those counted in cm110PortSingles, cm110PortMultiple , cm1110PortExcessives or cm110PortLates objects. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.31Counter32read-onlycurrent
cm110PortSingles
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced exactly one collision. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.32Counter32read-onlycurrent
cm110PortMultiples
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced more than one collision. This counter is aplicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.33Counter32read-onlycurrent
cm110PortExcessives
OBJECT-TYPE
An Egress counter that counts the number frames dropped in the transmit MAC because the frame experienced 16 consecutive collisions. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.34Counter32read-onlycurrent
cm110PortLates
OBJECT-TYPE
An Egress counter that counts the number times a collision is detected later than 512 bits-times into the transmission of a frame. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.35Counter32read-onlycurrent
cm110PortOutFcsErrs
OBJECT-TYPE
An Egress counter that counts the number frames transmitted with an invalid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.36Counter32read-onlycurrent
cm110PortResetCounters
OBJECT-TYPE
Allows the resetting of all cm110RateConvStats statistical counters for this port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.4.1.37YesNoValueread-writecurrent
cm110RateConvVctTable
OBJECT-TYPE
Table of CM-110 type media converter module's
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5not-accessiblecurrent
cm110RateConvVctEntry
OBJECT-TYPE
Entries of the table, each relating to a separate fiber or copper port on the CM-110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1not-accessiblecurrent
cm110VctSlotIndex
OBJECT-TYPE
The Slot number the CM-1110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.2SlotNumbernot-accessiblecurrent
cm110VctStart
OBJECT-TYPE
Set this self-clearing variable to yes initiate the Advanced Virtual Cable Test. Note: During the test, no network data will be passed.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.3YesNoValueread-writecurrent
cm110VctStatus
OBJECT-TYPE
This object identifies the stat of the Advanced Virtual Cable Test.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.4INTEGER {notStarted(0), inProgress(1), testComplete(2)}read-onlycurrent
cm110VctTxPairResults
OBJECT-TYPE
Test result code returned from Virtual Cable Test of the Tx pair.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.5INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
cm110VctTxPairAmplitude
OBJECT-TYPE
Amplitude of Tx pair in Volts.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.6DisplayString (SIZE(0..20))read-onlycurrent
cm110VctTxPairDistance
OBJECT-TYPE
Distance in meters to fault when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.7DisplayString (SIZE(0..20))read-onlycurrent
cm110VctRxPairResults
OBJECT-TYPE
Test result code returned from Virtual Cable Test of the Rx pair.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.8INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
cm110VctRxPairAmplitude
OBJECT-TYPE
Amplitude of Rx pair in Volts.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.9DisplayString (SIZE(0..20))read-onlycurrent
cm110VctRxPairDistance
OBJECT-TYPE
Distance in meters to fault when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.4.5.1.10DisplayString (SIZE(0..20))read-onlycurrent
mcrMgt
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.5
mcrMgtTable
OBJECT-TYPE
Table of MCR-MGT management module status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.1not-accessiblecurrent
mcrMgtEntry
OBJECT-TYPE
Entries of the table, each relating to a separate MCR-MGT type management module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.1.1not-accessiblecurrent
mcrMgtSlotIndex
OBJECT-TYPE
The Slot number the MCR-MGT module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.1.1.2SlotNumbernot-accessiblecurrent
mcrMgtModelName
OBJECT-TYPE
This object identifies the model name of management module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.1.1.3DisplayStringread-onlycurrent
mcrMgtModelDesc
OBJECT-TYPE
This object identifies a static description of the management module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.1.1.4DisplayStringread-onlycurrent
mcrMgtFailSafeBootLoaderVer
OBJECT-TYPE
This object identifies the fail-safe bootloader version of the management module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.1.1.5DisplayStringread-onlycurrent
mcrMgtUpTime
OBJECT-TYPE
This object identifies the time (in hundredths of a second) since the management module was last re-initialized.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.1.1.6TimeTicksread-onlycurrent
mcrMgtConsoleDSR
OBJECT-TYPE
This object identifies the current status of the DSR signal, (active or inactive)
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.1.1.7OnOffValueread-onlycurrent
mcrMgtConfigTable
OBJECT-TYPE
Table of MCR-MGT management module Hardware configuration type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2not-accessiblecurrent
mcrMgtConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate MCR-MGT type management module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1not-accessiblecurrent
mcrMgtConfigSlotIndex
OBJECT-TYPE
The Slot number the MCR-MGT module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.2SlotNumbernot-accessiblecurrent
mcrMgtConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.3ContainerStatusread-writecurrent
mcrMgtConfigEthSpeedDuplex
OBJECT-TYPE
Define the Ethernet connection speed/duplex of the twisted pair interface.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.4INTEGER {auto(0), speed10Half(1), speed10Full(2), speed100Half(3), speed100Full(4), speed1000(7)}read-writecurrent
mcrMgtConfigEthCrossover
OBJECT-TYPE
Define the Ethernet connection crossover TX/RX Pair orientation of the twisted pair interface as auto(0), mdi(1) (straight through) or mdix(2) (crossed over).
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.5INTEGER {auto(0), mdi(1), mdix(2)}read-writecurrent
mcrMgtConfigConsolePortEnabled
OBJECT-TYPE
Determines whether the management module's console port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.6YesNoValueread-writecurrent
mcrMgtConfigConsoleSpeed
OBJECT-TYPE
Specifies the baud rate of the console port; keep in mind that speed is affected by the length of the cable.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.7INTEGER {b9600(13), b19200(14), b38400(15), b57600(16), b115200(17)}read-writecurrent
mcrMgtConfigConsoleDataBits
OBJECT-TYPE
Specifies the number of bits in a byte.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.8INTEGER {d7(2), d8(3)}read-writecurrent
mcrMgtConfigConsoleParity
OBJECT-TYPE
Specifies if you are using Even, Odd, or No parity on the console.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.9INTEGER {none(0), odd(1), even(2)}read-writecurrent
mcrMgtConfigConsoleStopBits
OBJECT-TYPE
Specifies the number of stop bits that follow a byte.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.10INTEGER {s1(0), s2(1)}read-writecurrent
mcrMgtConfigConsoleFlowControl
OBJECT-TYPE
Defines whether the data flow is handled by the software (Soft), hardware (Hard), both or None.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.11INTEGER {none(0), soft(1), hard(2), both(3)}read-writecurrent
mcrMgtConfigConsoleMonitorDSR
OBJECT-TYPE
Specifies whether the RS-232 signal DSR (Data Set Ready) should be monitored, for the console port. When DSR is monitored and the management module detects the DSR signal go inactive then the current console management session will be reset.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.2.1.12OnOffValueread-writecurrent
mcrMgtLedTable
OBJECT-TYPE
Table of MCR-MGT management module LED information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.3not-accessiblecurrent
mcrMgtLedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate MCR-MGT type management module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.3.1not-accessiblecurrent
mcrMgtLedSlotIndex
OBJECT-TYPE
The Slot number the MCR-MGT module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.3.1.2SlotNumbernot-accessiblecurrent
mcrMgtLedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the management module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.3.1.3INTEGER {off(0), onGreen(1)}read-onlycurrent
mcrMgtLedALM
OBJECT-TYPE
This object identifies the status of the alarm (ALM) LED on the management module. Possible status values are: offNoAlarms(0) - Normal operating condition onRedAlarmsPresent(1) - System hardware or software alarms present
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.3.1.4INTEGER {offNoAlarms(0), onRedAlarmsPresent(1)}read-onlycurrent
mcrMgtLedLKC
OBJECT-TYPE
This object identifies the status of the link copper (LKC) LED on the management module. Possible status values are: offLinkDown(0) - Copper link status is DOWN onGreenLinkUp(1) - Copper link status is UP
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.3.1.5INTEGER {offLinkDown(0), onGreenLinkUp(1)}read-onlycurrent
mcrMgtLedCopperSpeed
OBJECT-TYPE
This object identifies the status of the link copper speed (100/1000) LED on the management module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.3.1.6INTEGER {off10Mbps(0), onYellow100Mbps(1), onGreen1000Mbps(2)}read-onlycurrent
mcrMgtEthStatsTable
OBJECT-TYPE
Table of MCR-MGT management module Ethernet status and statistics information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4not-accessiblecurrent
mcrMgtEthStatsEntry
OBJECT-TYPE
An entry in the Ethernet statistics table, each relating to an Ethernet interface.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1not-accessiblecurrent
mgtEthSlotIndex
OBJECT-TYPE
The Slot number the MCR-MGT module is currently inserted.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.2SlotNumbernot-accessiblecurrent
mgtEthStatsIfIndex
OBJECT-TYPE
The Ethernet interface number.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.3GenericTableIndexnot-accessiblecurrent
mgtEthStatsName
OBJECT-TYPE
Displays Ethernet interface name.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.4DisplayStringread-onlycurrent
mgtEthStatsMacAddress
OBJECT-TYPE
Displays the MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.5MacAddressread-onlycurrent
mgtEthStatsStatus
OBJECT-TYPE
Displays the Ethernet link status - down(0) or up(1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.6INTEGER {down(0), up(1)}read-onlycurrent
mgtEthStatsSpeedDuplex
OBJECT-TYPE
Current status of the Ethernet connection speed/duplex twisted pair interface. When the management module does not know the pair speed/duplex, this variable has the value unknown(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.7INTEGER {unknown(0), speed10Half(1), speed10Full(2), speed100Half(3), speed100Full(4), speed1000Half(5), speed1000Full(6)}read-onlycurrent
mgtEthStatsBroadcast
OBJECT-TYPE
The management module's Ethernet Broadcast Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.8YesNoValueread-onlycurrent
mgtEthStatsDebug
OBJECT-TYPE
The management module's Ethernet Debug Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.9YesNoValueread-onlycurrent
mgtEthStatsLoopback
OBJECT-TYPE
The management module's Ethernet Loopback Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.10YesNoValueread-onlycurrent
mgtEthStatsPointtoPoint
OBJECT-TYPE
The management module's Ethernet Point to Point Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.11YesNoValueread-onlycurrent
mgtEthStatsNoTrailers
OBJECT-TYPE
The management module's Ethernet No Trailers Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.12YesNoValueread-onlycurrent
mgtEthStatsRunning
OBJECT-TYPE
The management module's Ethernet Running Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.13YesNoValueread-onlycurrent
mgtEthStatsNoArp
OBJECT-TYPE
The management module's Ethernet No Arp Protocol Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.14YesNoValueread-onlycurrent
mgtEthStatsPromiscuous
OBJECT-TYPE
The management module's Ethernet Promiscuous Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.15YesNoValueread-onlycurrent
mgtEthStatsRxMulticast
OBJECT-TYPE
The management module's Ethernet Receive all Multicast Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.16YesNoValueread-onlycurrent
mgtEthStatsMasterLoadBalancer
OBJECT-TYPE
The management module's Ethernet Master Load Balancer Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.17YesNoValueread-onlycurrent
mgtEthStatsSlaveLoadBalancer
OBJECT-TYPE
The management module's Ethernet Slave Load Balancer Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.18YesNoValueread-onlycurrent
mgtEthStatsMulticast
OBJECT-TYPE
The management module's Ethernet Multicast Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.19YesNoValueread-onlycurrent
mgtEthStatsSetMedia
OBJECT-TYPE
The management module's Ethernet Set Media Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.20YesNoValueread-onlycurrent
mgtEthStatsAutoMedia
OBJECT-TYPE
The management module's Ethernet Auto Media Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.21YesNoValueread-onlycurrent
mgtEthStatsDynamic
OBJECT-TYPE
The management module's Ethernet Dynamic Flags status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.22YesNoValueread-onlycurrent
mgtEthStatsLocalAddress
OBJECT-TYPE
The management module's Ethernet local IPv4 address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.23IpAddressread-onlycurrent
mgtEthStatsSubnetMask
OBJECT-TYPE
The management module's Ethernet IPv4 subnet mask.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.24IpAddressread-onlycurrent
mgtEthStatsBroadcastAddress
OBJECT-TYPE
The management module's Ethernet Broadcast address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.25IpAddressread-onlycurrent
mgtEthStatsMtu
OBJECT-TYPE
The management module's Ethernet MTU.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.26Unsigned32read-onlycurrent
mgtEthStatsTxQLen
OBJECT-TYPE
The management module's Ethernet TX Queue Length.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.27Unsigned32read-onlycurrent
mgtEthStatsRxBytes
OBJECT-TYPE
The management module's Ethernet RX Bytes count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.28Counter32read-onlycurrent
mgtEthStatsTxBytes
OBJECT-TYPE
The management module's Ethernet TX Bytes count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.29Counter32read-onlycurrent
mgtEthStatsRxPackets
OBJECT-TYPE
The management module's Ethernet RX Packets count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.30Counter32read-onlycurrent
mgtEthStatsTxPackets
OBJECT-TYPE
The management module's Ethernet TX Packets count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.31Counter32read-onlycurrent
mgtEthStatsRxErrors
OBJECT-TYPE
The management module's Ethernet RX Packets Errors count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.32Counter32read-onlycurrent
mgtEthStatsTxPktErrors
OBJECT-TYPE
The management module's Ethernet TX Packets Errors count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.33Counter32read-onlycurrent
mgtEthStatsRxDroppedPkts
OBJECT-TYPE
The management module's Ethernet RX Dropped packets count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.34Counter32read-onlycurrent
mgtEthStatsTxDroppedPkts
OBJECT-TYPE
The management module's Ethernet TX Dropped packets count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.35Counter32read-onlycurrent
mgtEthStatsRxOverruns
OBJECT-TYPE
The management module's Ethernet RX Overruns count
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.36Counter32read-onlycurrent
mgtEthStatsTxOverruns
OBJECT-TYPE
The management module's Ethernet TX Overruns count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.37Counter32read-onlycurrent
mgtEthStatsRxFrameErrs
OBJECT-TYPE
The management module's Ethernet RX Frame Errors count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.38Counter32read-onlycurrent
mgtEthStatsTxCarrierErrs
OBJECT-TYPE
The management module's Ethernet TX Carrier Errors count
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.39Counter32read-onlycurrent
mgtEthStatsCollisions
OBJECT-TYPE
The management module's Ethernet Collisions count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.5.4.1.40Counter32read-onlycurrent
cm1000mmFixed
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.6
cm1000mmFixedTable
OBJECT-TYPE
Table of CM-1000MM type media converter module's status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1not-accessiblecurrent
cm1000mmFixedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1000MM type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1not-accessiblecurrent
cm1000mmSlotIndex
OBJECT-TYPE
The Slot number the CM-1000MM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.2SlotNumbernot-accessiblecurrent
cm1000mmModelname
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.3DisplayStringread-onlycurrent
cm1000mmModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.4DisplayStringread-onlycurrent
cm1000mmHwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware jumper J5 on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media converter module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm1000mmHwSw1FiberAutoNeg
OBJECT-TYPE
Media converter module's current switch setting for fiber Auto-Negotiation.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.6INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm1000mmHwSw2LinkMode
OBJECT-TYPE
Media converter module's current switch setting for Link Mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.7INTEGER {swDownSmartLinkPassthrough(0), swUpStandard(1)}read-onlycurrent
cm1000mmHwSw3FiberFaultAlert
OBJECT-TYPE
Media converter module's current switch setting for Fiber Fault Alert.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.8INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm1000mmHwSw4Loopback1
OBJECT-TYPE
Media converter module's current switch setting for loopback (fiber port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.9INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
cm1000mmHwSw5Loopback2
OBJECT-TYPE
Media converter module's current switch setting for loopback (fiber port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.10INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
cm1000mmFiber1LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.12INTEGER {down(0), up(1)}read-onlycurrent
cm1000mmFiber1ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.13INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6)}read-onlycurrent
cm1000mmFiber1AutoNegState
OBJECT-TYPE
Media converter module's current fiber auto-negotiation state (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.14INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm1000mmFiber1Speed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.15INTEGER {speed1000Mbps(2)}read-onlycurrent
cm1000mmFiber1Duplex
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.16INTEGER {half(0), full(1)}read-onlycurrent
cm1000mmFiber1PauseEnh
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.17INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm1000mmFiber1LPRFStatus
OBJECT-TYPE
Media converter module's fiber Link Partner Remote Fault status (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.18INTEGER {ok(0), offline(1), linkFault(2), autoNegError(3)}read-onlycurrent
cm1000mmFiber1ReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port (port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.19INTEGER {fault(0), ok(1)}read-writecurrent
cm1000mmFiber2LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.20INTEGER {down(0), up(1)}read-onlycurrent
cm1000mmFiber2ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.21INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6)}read-onlycurrent
cm1000mmFiber2AutoNegState
OBJECT-TYPE
Media converter module's current fiber auto-negotiation state (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.22INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm1000mmFiber2Speed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.23INTEGER {speed1000Mbps(2)}read-onlycurrent
cm1000mmFiber2Duplex
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.24INTEGER {half(0), full(1)}read-onlycurrent
cm1000mmFiber2PauseEnh
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.25INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm1000mmFiber2LPRFStatus
OBJECT-TYPE
Media converter module's fiber Link Partner Remote Fault status (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.26INTEGER {ok(0), offline(1), linkFault(2), autoNegError(3)}read-onlycurrent
cm1000mmFiber2ReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port (port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.27INTEGER {fault(0), ok(1)}read-writecurrent
cm1000mmFiberLoopBack
OBJECT-TYPE
Media converter module's current fiber loopback mode setting. Writing to this object will change the current settings. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.1.1.28INTEGER {disabled(0), port1(1), port2(2)}read-writecurrent
cm1000mmConfigTable
OBJECT-TYPE
Table of CM-1000MM type media converter module's configuration type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2not-accessiblecurrent
cm1000mmConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1000MM type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1not-accessiblecurrent
cm1000mmConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-1000MM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.2SlotNumbernot-accessiblecurrent
cm1000mmConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.3ContainerStatusread-writecurrent
cm1000mmConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm1000mmConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.5INTEGER {standard(0), smartLinkPassthrough(1)}read-writecurrent
cm1000mmConfigFiberFaultAlert
OBJECT-TYPE
This object identifies the Fiber Fault Alert setting for the media module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.6EnableDisableValueread-writecurrent
cm1000mmConfigJumboPackets
OBJECT-TYPE
This object identifies the Jumbo Packet setting for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.7EnableDisableValueread-writecurrent
cm1000mmConfigFiberAutoNeg
OBJECT-TYPE
This object identifies the wither fiber auto-negotiation is enabled for both ports. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.8EnableDisableValueread-writecurrent
cm1000mmConfigFiber1PortName
OBJECT-TYPE
This object identifies a user definable name for the fiber port (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.9DisplayString (SIZE(0..8))read-writecurrent
cm1000mmConfigFiber1PortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.10YesNoValueread-writecurrent
cm1000mmConfigFiber2PortName
OBJECT-TYPE
This object identifies a user definable name for the fiber port (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.11DisplayString (SIZE(0..8))read-writecurrent
cm1000mmConfigFiber2PortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.2.1.12YesNoValueread-writecurrent
cm1000mmLedTable
OBJECT-TYPE
Table of CM-1000MM type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.3not-accessiblecurrent
cm1000mmLedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1000MM type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.3.1not-accessiblecurrent
cm1000mmLedsSlotIndex
OBJECT-TYPE
The Slot number the CM-1000 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.3.1.2SlotNumbernot-accessiblecurrent
cm1000mmLedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Fiber loopback enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm1000mmLedLK1
OBJECT-TYPE
This object identifies the status of the link fiber port 1 (LK1) LED on the media converter module. Possible status values are: off(0) - No fiber link on(1) - Fiber link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.3.1.4INTEGER {off(0), on(1)}read-onlycurrent
cm1000mmLedLK2
OBJECT-TYPE
This object identifies the status of the link fiber port 2 (LK2) LED on the media converter module. Possible status values are: off(0) - No fiber link on(1) - Fiber link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.6.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
cm100mmFixed
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.7
cm100mmFixedTable
OBJECT-TYPE
Table of CM-100MM type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1not-accessiblecurrent
cm100mmFixedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-100MM type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1not-accessiblecurrent
cm100mmSlotIndex
OBJECT-TYPE
The Slot number the CM-100MM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.2SlotNumbernot-accessiblecurrent
cm100mmModelName
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.3DisplayStringread-onlycurrent
cm100mmModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.4DisplayStringread-onlycurrent
cm100mmHwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware switch on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm100mmHwSw1LinkPassthrough
OBJECT-TYPE
Media converter module's current switch setting for Link Passthrough.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.6INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm100mmHwSw2FarEndFault
OBJECT-TYPE
Media converter module's current switch setting for Far-End Fault.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.7INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm100mmHwSw3Loopback1
OBJECT-TYPE
Media converter module's current switch setting for Loopback (fiber port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.8INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
cm100mmHwSw4Loopback2
OBJECT-TYPE
Media converter module's current switch setting for Loopback (fiber port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.9INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
cm100mmFiber1LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.12INTEGER {down(0), up(1)}read-onlycurrent
cm100mmFiber1ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.13INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6)}read-onlycurrent
cm100mmFiber1Speed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.14INTEGER {speed100Mbps(1)}read-onlycurrent
cm100mmFiber1FarEndFault
OBJECT-TYPE
Media converter module's current fiber Far End Fault status (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.15INTEGER {disable(0), ok(1), receivingFEF(2), sendingFEF(3)}read-onlycurrent
cm100mmFiber1ReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port (port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.16INTEGER {fault(0), ok(1)}read-writecurrent
cm100mmFiber2LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.17INTEGER {down(0), up(1)}read-onlycurrent
cm100mmFiber2ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.18INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6)}read-onlycurrent
cm100mmFiber2Speed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.19INTEGER {speed100Mbps(1)}read-onlycurrent
cm100mmFiber2FarEndFault
OBJECT-TYPE
Media converter module's current fiber Far End Fault status (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.20INTEGER {disable(0), ok(1), receivingFEF(2), sendingFEF(3)}read-onlycurrent
cm100mmFiber2ReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port (port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.21INTEGER {fault(0), ok(1)}read-writecurrent
cm100mmFiberLoopBack
OBJECT-TYPE
This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.1.1.22INTEGER {disabled(0), port1(1), port2(2)}read-writecurrent
cm100mmConfigTable
OBJECT-TYPE
Table of CM-100MM type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2not-accessiblecurrent
cm100mmConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-100MM type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1not-accessiblecurrent
cm100mmConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-100MM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.2SlotNumbernot-accessiblecurrent
cm100mmConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.3ContainerStatusread-writecurrent
cm100mmConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm100mmConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.5INTEGER {standard(0), linkPassthrough(1)}read-writecurrent
cm100mmConfigFiberFarEndFault
OBJECT-TYPE
This object identifies the fiber Far End Fault setting for the media module. This setting is always enabled if Link Mode is set to linkPassthrough. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.6EnableDisableValueread-writecurrent
cm100mmConfigFiber1PortName
OBJECT-TYPE
This object identifies a user definable name for the fiber port (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.7DisplayString (SIZE(0..8))read-writecurrent
cm100mmConfigFiber1PortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.8YesNoValueread-writecurrent
cm100mmConfigFiber2PortName
OBJECT-TYPE
This object identifies a user definable name for the fiber port (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.9DisplayString (SIZE(0..8))read-writecurrent
cm100mmConfigFiber2PortEnable
OBJECT-TYPE
This object identifies whether the fiber port is enabled (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.2.1.10YesNoValueread-writecurrent
cm100mmLedTable
OBJECT-TYPE
Table of CM-100MM type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.3not-accessiblecurrent
cm100mmLedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-100MM type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.3.1not-accessiblecurrent
cm100mmLedSlotIndex
OBJECT-TYPE
The Slot number the CM-100MM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.3.1.2SlotNumbernot-accessiblecurrent
cm100mmLedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Fiber loopback enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm100mmLedLK1
OBJECT-TYPE
This object identifies the status of the link fiber port 1 (LK1) LED on the media converter module. Possible status values are: off(0) - No fiber link on(1) - Fiber link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.3.1.4INTEGER {off(0), on(1)}read-onlycurrent
cm100mmLedLK2
OBJECT-TYPE
This object identifies the status of the link fiber port 2 (LK2) LED on the media converter module. Possible status values are: off(0) - No fiber link on(1) - Fiber link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.7.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
cm10gFixed
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.8
cm10gFixedTable
OBJECT-TYPE
Table of CM-10G type media converter module's status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1not-accessiblecurrent
cm10gFixedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-10G type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1not-accessiblecurrent
cm10gSlotIndex
OBJECT-TYPE
The Slot number the CM-10G type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.2SlotNumbernot-accessiblecurrent
cm10gModelname
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.3DisplayStringread-onlycurrent
cm10gModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.4DisplayStringread-onlycurrent
cm10gHwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware jumper J5 on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media converter module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm10gHwSw1OperationMode
OBJECT-TYPE
Media converter module's current switch setting for operation mode. Data mode is for normal data transmission.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.6INTEGER {test(0), data(1)}read-onlycurrent
cm10gHwSw2LinkMode
OBJECT-TYPE
Media converter module's current switch setting for Link Mode. If the Operation switch is set to Test, then this object indicates whether the port is in loopback or performing the build in link-test.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.7INTEGER {swDownSmartLinkPassthrough(0), swUpStandard(1)}read-onlycurrent
cm10gHwSw3FiberFaultAlert
OBJECT-TYPE
Media converter module's current switch setting for Fiber Fault Alert. If the Operation switch is set to Test, then this object indicates which port is in test mode
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.8INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm10gHwSw4Port1EdcMode
OBJECT-TYPE
This oject indicates the current switch setting for EDC auto mode for port 1. This object only applies to SFP moudles.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.9INTEGER {disabled(0), enabled(1)}read-onlycurrent
cm10gHwSw5Port2EdcMode
OBJECT-TYPE
This oject indicates the current switch setting for EDC auto mode for port 2. This object only applies to SFP moudles.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.10INTEGER {disabled(0), enabled(1)}read-onlycurrent
cm10gPort1LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.11INTEGER {down(0), up(1), shutdown(2)}read-onlycurrent
cm10gPort1ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.12INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6), xfp(7), sfpPlus(8)}read-onlycurrent
cm10gPort1AutoNegState
OBJECT-TYPE
Media converter module's current fiber auto-negotiation state (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.13INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm10gPort1Speed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.14INTEGER {speed10Mbps(0), speed100Mbps(1), speed1000Mbps(2), speed10Gbps(3)}read-onlycurrent
cm10gPort1Duplex
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.15INTEGER {half(0), full(1)}read-onlycurrent
cm10gPort1PauseEnh
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.16INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm10gPort1ReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port (port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.17INTEGER {fault(0), ok(1)}read-onlycurrent
cm10gPort2LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.18INTEGER {down(0), up(1), shutdown(2)}read-onlycurrent
cm10gPort2ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.19INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6), xfp(7), sfpPlus(8)}read-onlycurrent
cm10gPort2AutoNegState
OBJECT-TYPE
Media converter module's current fiber auto-negotiation state (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.20INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm10gPort2Speed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.21INTEGER {speed10Mbps(0), speed100Mbps(1), speed1000Mbps(2), speed10Gbps(3)}read-onlycurrent
cm10gPort2Duplex
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.22INTEGER {half(0), full(1)}read-onlycurrent
cm10gPort2PauseEnh
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.23INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm10gPort2ReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port (port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.24INTEGER {fault(0), ok(1)}read-onlycurrent
cm10gPortLoopBack
OBJECT-TYPE
Media converter module's current port loopback mode setting. Writing to this object will change the current settings. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.25INTEGER {disabled(0), port1(1), port2(2)}read-writecurrent
cm10gPortTestMode
OBJECT-TYPE
Media converter module's current port test mode setting.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.1.1.26INTEGER {disabled(0), port1(1), port2(2)}read-onlycurrent
cm10gConfigTable
OBJECT-TYPE
Table of CM-10G type media converter module's configuration type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2not-accessiblecurrent
cm10gConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-10G type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1not-accessiblecurrent
cm10gConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-10G type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.2SlotNumbernot-accessiblecurrent
cm10gConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.3ContainerStatusread-writecurrent
cm10gConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm10gConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.5INTEGER {standard(0), smartLinkPassthrough(1)}read-writecurrent
cm10gConfigFiberFaultAlert
OBJECT-TYPE
This object identifies the Fiber Fault Alert setting for the media module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.6EnableDisableValueread-writecurrent
cm10gConfigFiberAutoNeg
OBJECT-TYPE
This object identifies the wither fiber auto-negotiation is enabled for both ports. This only applies if 1G SFP modules are in use. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.7EnableDisableValueread-writecurrent
cm10gConfigPort1Name
OBJECT-TYPE
This object identifies a user definable name for port 1.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.8DisplayString (SIZE(0..8))read-writecurrent
cm10gConfigPort1Enable
OBJECT-TYPE
This object identifies whether port 1 is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.9YesNoValueread-writecurrent
cm10gConfigPort1EdcMode
OBJECT-TYPE
This object identifies the EDC mode for this port. This config option only applies for an SFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.10INTEGER {auto(0), alternate(1), linear(2), limiting(3), cx1(4)}read-writecurrent
cm10gConfigPort1FecEnable
OBJECT-TYPE
This object identifies the whether FEC control is enabled for this port. This config option only applies for an XFP module. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.11YesNoValueread-writecurrent
cm10gConfigPort1FecAmplitude
OBJECT-TYPE
This object identifies the FEC Amplitude value for this port. This config option only applies for an XFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.12INTEGER (-128..127)read-writecurrent
cm10gConfigPort1FecPhase
OBJECT-TYPE
This object identifies the FEC phase value for this port. This config option only applies for an XFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.13INTEGER (-128..127)read-writecurrent
cm10gConfigPort1WavelengthEnable
OBJECT-TYPE
This object identifies whether Wavelength fine tuning is enabled for this port. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.14YesNoValueread-writecurrent
cm10gConfigPort1WavelengthValue
OBJECT-TYPE
This object identifies Wavelength fine tuning value for this port. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.15INTEGER (0..65535)read-writecurrent
cm10gConfigPort1ChannelEnable
OBJECT-TYPE
This object identifies whether channel number fine tuning is enabled for this port. This config option only applies for an XFP module. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.16YesNoValueread-writecurrent
cm10gConfigPort1ChannelNumber
OBJECT-TYPE
This object identifies the channel number fine tuning value for this port. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.17INTEGER (1..65535)read-writecurrent
cm10gConfigPort1TxDitherEnable
OBJECT-TYPE
This object identifies the whether TX Dither control is enabled on this port. If not enabled the default TX Dither value will be used. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.18YesNoValueread-writecurrent
cm10gConfigPort1TxDitherValue
OBJECT-TYPE
This object identifies the whether TX Dither is enabled for this port. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.19EnableDisableValueread-writecurrent
cm10gConfigPort2Name
OBJECT-TYPE
This object identifies a user definable name for port 2.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.20DisplayString (SIZE(0..8))read-writecurrent
cm10gConfigPort2Enable
OBJECT-TYPE
This object identifies whether port 2 is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.21YesNoValueread-writecurrent
cm10gConfigPort2EdcMode
OBJECT-TYPE
This object identifies the EDC mode for this port. This config option only applies for an SFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.22INTEGER {auto(0), alternate(1), linear(2), limiting(3), cx1(4)}read-writecurrent
cm10gConfigPort2FecEnable
OBJECT-TYPE
This object identifies the whether FEC control is enabled for this port. This config option only applies for an XFP module. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.23YesNoValueread-writecurrent
cm10gConfigPort2FecAmplitude
OBJECT-TYPE
This object identifies the FEC Amplitude value for this port. This config option only applies for an XFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.24INTEGER (-128..127)read-writecurrent
cm10gConfigPort2FecPhase
OBJECT-TYPE
This object identifies the FEC phase value for this port. This config option only applies for an XFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.25INTEGER (-128..127)read-writecurrent
cm10gConfigPort2WavelengthEnable
OBJECT-TYPE
This object identifies whether Wavelength fine tuning is enabled for this port. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.26YesNoValueread-writecurrent
cm10gConfigPort2WavelengthValue
OBJECT-TYPE
This object identifies Wavelength fine tuning value for this port. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.27INTEGER (0..65535)read-writecurrent
cm10gConfigPort2ChannelEnable
OBJECT-TYPE
This object identifies whether channel number fine tuning is enabled for this port. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.28YesNoValueread-writecurrent
cm10gConfigPort2ChannelNumber
OBJECT-TYPE
This object identifies the channel number fine tuning value for this port. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.29INTEGER (1..65535)read-writecurrent
cm10gConfigPort2TxDitherEnable
OBJECT-TYPE
This object identifies the whether TX Dither control is enabled on this port. If not enabled the default TX Dither value will be used. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.30YesNoValueread-writecurrent
cm10gConfigPort2TxDitherValue
OBJECT-TYPE
This object identifies the whether TX Dither is enabled for this port. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.2.1.31EnableDisableValueread-writecurrent
cm10gLedTable
OBJECT-TYPE
Table of CM-10G type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.3not-accessiblecurrent
cm10gLedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-10G type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.3.1not-accessiblecurrent
cm10gLedsSlotIndex
OBJECT-TYPE
The Slot number the CM-10G type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.3.1.2SlotNumbernot-accessiblecurrent
cm10gLedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Loopback or Link-Test enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm10gLedLK1
OBJECT-TYPE
This object identifies the status of the port 1 link (LK1) LED on the media converter module. Possible status values are: off(0) - No link on(1) - Port link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.3.1.4INTEGER {off(0), on(1)}read-onlycurrent
cm10gLedLK2
OBJECT-TYPE
This object identifies the status of the port 2 link (LK2) LED on the media converter module. Possible status values are: off(0) - No link on(1) - Port link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.8.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
exCM
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.9
exCMTable
OBJECT-TYPE
Table of CM-1110 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1not-accessiblecurrent
exCMEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1not-accessiblecurrent
exCMSlotIndex
OBJECT-TYPE
The Slot number the CM-1110 type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.2SlotNumbernot-accessiblecurrent
exCMModelName
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.3DisplayStringread-onlycurrent
exCMModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.4DisplayStringread-onlycurrent
exCMHwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware switch on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
exCMHwSw1AutoLocalRemote
OBJECT-TYPE
Media converter module's current switch setting for VDSL role.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.6INTEGER {swDownRemote(0), swUpAutoLocal(1)}read-onlycurrent
exCMHwSw2Rate
OBJECT-TYPE
Media converter module's current switch setting for VDSL rate/reach.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.7INTEGER {swDownLongRange(0), swUpHighSpeed(1)}read-onlycurrent
exCMHwSw3SymmetricAsymmetric
OBJECT-TYPE
Media converter module's current switch setting for VDSL band plan.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.8INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
exCMHwSw4SnrRatio
OBJECT-TYPE
Media converter module's current switch setting for VDSL signal-to-noise ratio.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.9INTEGER {swDown6db(0), swUp9db(1)}read-onlycurrent
exCMHwSw5Loopback
OBJECT-TYPE
Media converter module's current switch setting for VDSL loopback.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.10INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
exCMHwSw6EthAutoNeg
OBJECT-TYPE
Media converter module's current switch setting for ethernet auto-negotiation.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.11INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
exCMHwSw7EthSpeed
OBJECT-TYPE
Media converter module's current switch setting for ethernet speed (when auto-negotiation is disabled).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.12INTEGER {swDown10Mbps(0), swUp100Mbps(1)}read-onlycurrent
exCMHwSw8EthDuplex
OBJECT-TYPE
Media converter module's current switch setting for ethernet duplex (when auto-negotiation is disabled).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.13INTEGER {swDownHalf(0), swUpFull(1)}read-onlycurrent
exCMHwSw9LinkMode
OBJECT-TYPE
Media converter module's current switch setting for link mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.14INTEGER {swDownLinkPassthrough(0), swUpStandard(1)}read-onlycurrent
exCMHwSw10InterlinkFaultFeedback
OBJECT-TYPE
Media converter module's current switch setting for interlink fault feedback.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.15INTEGER {swDownEnabled(0), swUpDisabled(1)}read-onlycurrent
exCMVdslLinkStatus
OBJECT-TYPE
Media converter module's current VDSL link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.16INTEGER {idle(0), handshake(1), training(2), up(3), upLogicallyDown(4)}read-onlycurrent
exCMVdslConnType
OBJECT-TYPE
Media converter module's VDSL port connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.17INTEGER {rj45(9), terminalBlock(10), bnc(11)}read-onlycurrent
exCMVdslLoopBack
OBJECT-TYPE
This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.18EnableDisableValueread-writecurrent
exCMVdslRole
OBJECT-TYPE
This object identifies the VDSL port's current role.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.19INTEGER {local(0), remote(1)}read-onlycurrent
exCMVdslProfile
OBJECT-TYPE
This object identifies the VDSL port's current profile. This value has no meaning when the VDSL role is remote.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.20INTEGER {notApplicable(0), profile1-AnnexA-R-POTS-D-32-EU-32-30a(1), profile2-AnnexA-R-POTS-D-32-EU-32-17a(2), profile3-AnnexA-R-POTS-D-32-EU-32-12b(3), profile4-AnnexA-R-POTS-D-32-EU-32-12a(4), profile5-AnnexA-R-POTS-D-32-EU-32-8a(5), profile6-AnnexA-R-POTS-D-32-EU-32-8b(6), profile7-AnnexA-R-POTS-D-32-EU-32-8c(7), profile8-AnnexA-R-POTS-D-32-EU-32-8d(8), profile9-AnnexA-R-POTS-D-64-EU-64-30a-NUS0(9), profile10-AnnexA-R-POTS-D-64-EU-64-17a(10), profile11-AnnexB-B7-3-997-M1x-M(11), profile12-AnnexB-B7-4-997-M2x-M-8(12), profile13-AnnexB-B7-5-997-M2x-A(13), profile14-AnnexB-B7-6-997-M2x-M(14), profile15-AnnexB-B7-9-997E17-M2x-A(15), profile16-AnnexB-B7-10-997E30-M2x-NUS0(16), profile17-AnnexB-B8-1-998-M1x-A(17), profile18-AnnexB-B8-2-998-M1x-B(18), profile19-AnnexB-B8-4-998-M2x-A(19), profile20-AnnexB-B8-5-998-M2x-M(20), profile21-AnnexB-B8-6-998-M2x-B(21), profile22-AnnexB-B8-8-998E17-M2x-NUS0(22), profile23-AnnexB-B8-9-998E17-M2x-NUS0-M(23), profile24-AnnexB-B8-10-998ADE17-M2x-NUS0-M(24), profile25-AnnexB-B8-11-998E17-M2x-A(25), profile26-AnnexB-B8-12-998E17-M2x-B(26), profile27-AnnexB-B8-13-998E30-M2x-NUS0(27), profile28-AnnexB-B8-14-998E30-M2x-NUS0-M(28), profile29-AnnexB-B8-15-998ADE30-M2x-NUS0-M(29), profile30-AnnexB-B8-16-998ADE30-M2x-NUS0-A(30), profile31-AnnexC-POTS-25-138-b(31), profile32-AnnexC-POTS-25-276-b(32), profile33-AnnexC-TMC-ISDN(33)}read-onlycurrent
exCMVdslBitswapping
OBJECT-TYPE
This object identifies the VDSL port's current bitswapping status. This value has no meaning when the VDSL role is remote.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.21INTEGER {notApplicable(-1), off(0), on(1)}read-onlycurrent
exCMVdslStatusAttainableDataRateUp
OBJECT-TYPE
This object identifies the VDSL port's attainable data rate (upstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.22Integer32read-onlycurrent
exCMVdslStatusAttainableDataRateDown
OBJECT-TYPE
This object identifies the VDSL port's attainable data rate (downstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.23Integer32read-onlycurrent
exCMVdslStatusActualDataRateUp
OBJECT-TYPE
This object identifies the VDSL port's actual data rate (upstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.24Integer32read-onlycurrent
exCMVdslStatusActualDataRateDown
OBJECT-TYPE
This object identifies the VDSL port's actual data rate (downstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.25Integer32read-onlycurrent
exCMVdslStatusPrevDataRateUp
OBJECT-TYPE
This object identifies the VDSL port's previous data rate (upstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.26Integer32read-onlycurrent
exCMVdslStatusPrevDataRateDown
OBJECT-TYPE
This object identifies the VDSL port's previous data rate (downstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.27Integer32read-onlycurrent
exCMVdslStatusActualSnrUp
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (upstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.28Integer32read-onlycurrent
exCMVdslStatusActualSnrDown
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (downstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.29Integer32read-onlycurrent
exCMVdslStatusActualSnrUs0
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (upstream 0) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.30Integer32read-onlycurrent
exCMVdslStatusActualSnrUs1
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (upstream 1) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.31Integer32read-onlycurrent
exCMVdslStatusActualSnrDs1
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (downstream 1) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.32Integer32read-onlycurrent
exCMVdslStatusActualSnrUs2
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (upstream 2) in 0.2 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.33Integer32read-onlycurrent
exCMVdslStatusActualSnrDs2
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (downstream 2) in 0.2 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.34Integer32read-onlycurrent
exCMVdslStatusActualSnrUs3
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (upstream 3) in 0.3 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.35Integer32read-onlycurrent
exCMVdslStatusActualSnrDs3
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (downstream 3) in 0.3 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.36Integer32read-onlycurrent
exCMVdslStatusActualSnrUs4
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (upstream 4) in 0.4 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.37Integer32read-onlycurrent
exCMVdslStatusActualSnrDs4
OBJECT-TYPE
This object identifies the VDSL port's actual signal-to-noise ratio (downstream 4) in 0.4 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.38Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationUp
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (upstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.39Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationDown
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (downstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.40Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationUs0
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (upstream 0) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.41Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationUs1
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (upstream 1) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.42Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationDs1
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (downstream 1) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.43Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationUs2
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (upstream 2) in 0.2 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.44Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationDs2
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (downstream 2) in 0.2 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.45Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationUs3
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (upstream 3) in 0.3 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.46Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationDs3
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (downstream 3) in 0.3 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.47Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationUs4
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (upstream 4) in 0.4 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.48Integer32read-onlycurrent
exCMVdslStatusActualSignalAttenuationDs4
OBJECT-TYPE
This object identifies the VDSL port's actual signal attenuation (downstream 4) in 0.4 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.49Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationUp
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (upstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.50Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationDown
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (downstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.51Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationUs0
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (upstream 0) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.52Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationUs1
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (upstream 1) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.53Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationDs1
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (downstream 1) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.54Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationUs2
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (upstream 2) in 0.2 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.55Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationDs2
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (downstream 2) in 0.2 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.56Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationUs3
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (upstream 3) in 0.3 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.57Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationDs3
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (downstream 3) in 0.3 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.58Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationUs4
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (upstream 4) in 0.4 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.59Integer32read-onlycurrent
exCMVdslStatusActualLineAttenuationDs4
OBJECT-TYPE
This object identifies the VDSL port's actual line attenuation (downstream 4) in 0.4 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.60Integer32read-onlycurrent
exCMVdslStatusActualInterleaveDelayUp
OBJECT-TYPE
This object identifies the VDSL port's actual interleave delay (upstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.61Integer32read-onlycurrent
exCMVdslStatusActualInterleaveDelayDown
OBJECT-TYPE
This object identifies the VDSL port's actual interleave delay (downstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.62Integer32read-onlycurrent
exCMVdslStatusActualInpUp
OBJECT-TYPE
This object identifies the VDSL port's actual INP (impulse noise protection) (upstream).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.63Integer32read-onlycurrent
exCMVdslStatusActualInpDown
OBJECT-TYPE
This object identifies the VDSL port's actual INP (impulse noise protection) (downstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.64Integer32read-onlycurrent
exCMVdslStatusActualInterleavingDepthUp
OBJECT-TYPE
This object identifies the VDSL port's actual interleaving depth (upstream).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.65Integer32read-onlycurrent
exCMVdslStatusActualInterleavingDepthDown
OBJECT-TYPE
This object identifies the VDSL port's actual interleaving depth (impulse noise protection) (downstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.66Integer32read-onlycurrent
exCMVdslStatusActualInterleavingBlockUp
OBJECT-TYPE
This object identifies the VDSL port's actual interleaving block (upstream).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.67Integer32read-onlycurrent
exCMVdslStatusActualInterleavingBlockDown
OBJECT-TYPE
This object identifies the VDSL port's actual interleaving block (impulse noise protection) (downstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.68Integer32read-onlycurrent
exCMVdslStatusActualTransmitPowerUp
OBJECT-TYPE
This object identifies the VDSL port's actual transmit power (upstream) in 0.1 dBm.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.69Integer32read-onlycurrent
exCMVdslStatusActualTransmitPowerDown
OBJECT-TYPE
This object identifies the VDSL port's actual transmit power (downstream) in 0.1 dBm.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.70Integer32read-onlycurrent
exCMVdslStatusMaxDataRateUp
OBJECT-TYPE
This object identifies the VDSL port's maximum data rate (upstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.71Integer32read-onlycurrent
exCMVdslStatusMaxDataRateDown
OBJECT-TYPE
This object identifies the VDSL port's maximum data rate (downstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.72Integer32read-onlycurrent
exCMVdslStatusMinDataRateUp
OBJECT-TYPE
This object identifies the VDSL port's minimum data rate (upstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.73Integer32read-onlycurrent
exCMVdslStatusMinDataRateDown
OBJECT-TYPE
This object identifies the VDSL port's minimum data rate (downstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.74Integer32read-onlycurrent
exCMVdslStatusTargetSnrUp
OBJECT-TYPE
This object identifies the VDSL port's target signal-to-noise ratio (upstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.75Integer32read-onlycurrent
exCMVdslStatusTargetSnrDown
OBJECT-TYPE
This object identifies the VDSL port's target signal-to-noise ratio (downstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.76Integer32read-onlycurrent
exCMVdslStatusMaxInterleaveDelayUp
OBJECT-TYPE
This object identifies the VDSL port's maximum interleave delay (upstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.77Integer32read-onlycurrent
exCMVdslStatusMaxInterleaveDelayDown
OBJECT-TYPE
This object identifies the VDSL port's maximum interleave delay (downstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.78Integer32read-onlycurrent
exCMVdslStatusMinInpUp
OBJECT-TYPE
This object identifies the VDSL port's minimum INP (impulse noise protection) (upstream).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.79Integer32read-onlycurrent
exCMVdslStatusMinInpDown
OBJECT-TYPE
This object identifies the VDSL port's minimum INP (impulse noise protection) (downstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.80Integer32read-onlycurrent
exCMVdslRemoteLoopback
OBJECT-TYPE
Write remoteLoopbackOff(1) or remoteLoopbackOn(2) to this object to set the loopback state of the remote VDSL peer. This object's value represents the last loopback command sent to the peer.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.81INTEGER {none(0), remoteLoopbackOff(1), remoteLoopbackOn(2)}read-writecurrent
exCMVdslRemoteReset
OBJECT-TYPE
Write resetRemotePeer(1) to this object to reset the remote VDSL peer. This object's value has no meaning
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.82INTEGER {notApplicable(0), resetRemotePeer(1)}read-writecurrent
exCMEthernetLinkStatus
OBJECT-TYPE
Media converter module's current Ethernet link status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.83INTEGER {down(0), up(1)}read-onlycurrent
exCMEthernetConnType
OBJECT-TYPE
Media converter module's Ethernet connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.84INTEGER {rj45(0)}read-onlycurrent
exCMEthernetAutoNegState
OBJECT-TYPE
Media converter module's current Ethernet auto-negotiation state.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.85INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
exCMEthernetSpeed
OBJECT-TYPE
If Ethernet auto-negotiation state is complete then this object indicates the media converter module's current Ethernet auto-negotiated speed setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.86INTEGER {speed10Mbs(0), speed100Mbps(1), speed1000Mbps(2)}read-onlycurrent
exCMEthernetDuplex
OBJECT-TYPE
If Ethernet auto-negotiation state is complete then this object indicates the media converter module's current Ethernet auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.87INTEGER {half(0), full(1)}read-onlycurrent
exCMEthernetCrossOver
OBJECT-TYPE
If Ethernet auto-negotiation state is complete then this object indicates the media converter module's current Ethernet auto-negotiated MDI/MDI-X setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.88INTEGER {mdi(0), mdix(1)}read-onlycurrent
exCMEthernetPauseEnh
OBJECT-TYPE
If Ethernet auto-negotiation state is complete then this object indicates the media converter module's current Ethernet auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.89INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
exCMEthernetLPRFStatus
OBJECT-TYPE
Media converter module's Ethernet Link Partner Remote Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.90INTEGER {ok(0), remoteFault(1)}read-onlycurrent
exCMEthernetAutoSpeedDownshift
OBJECT-TYPE
This object identifies the status of the Ethernet auto speed downshift feature. noDownshift indicates that an automatic downshift of the Ethernet speed has not occurred.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.91INTEGER {noDownshift(0), downshift(1)}read-onlycurrent
exCMEthernetMDI
OBJECT-TYPE
This object identifies the Ethernet port's crossover status: MDI or MDI-X.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.92INTEGER {mdi(0), mdix(1)}read-onlycurrent
exCMVdslFirmwareVersion
OBJECT-TYPE
This object identifies the version of the VDSL firmware.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.93DisplayStringread-onlycurrent
exCMVdslFirmwareDate
OBJECT-TYPE
This object identifies the date of the VDSL firmware
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.94DateAndTimeread-onlycurrent
exCMVdslFirmwareDateString
OBJECT-TYPE
This object identifies the version of the VDSL firmware, in human-readable format.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.1.1.95DisplayStringread-onlycurrent
exCMConfigTable
OBJECT-TYPE
Table of CM-1110 type media converter module's configuration type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2not-accessiblecurrent
exCMConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1not-accessiblecurrent
exCMConfigSlotIndex
OBJECT-TYPE
The Slot number the ex-CM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.2SlotNumbernot-accessiblecurrent
exCMConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.3ContainerStatusread-writecurrent
exCMConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.4DisplayString (SIZE(0..63))read-writecurrent
exCMConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.5INTEGER {standard(0), smartLinkPassthrough(1)}read-writecurrent
exCMConfigInterlinkFaultFeedback
OBJECT-TYPE
This object identifies the interlink fault feedback setting for the media module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.6EnableDisableValueread-writecurrent
exCMConfigVdslPortName
OBJECT-TYPE
This object identifies a user definable name for the VDSL port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.7DisplayString (SIZE(0..8))read-writecurrent
exCMConfigVdslPortEnable
OBJECT-TYPE
This object identifies whether the VDSL port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.8YesNoValueread-writecurrent
exCMConfigVdslProfileMode
OBJECT-TYPE
This object specifies how the VDSL profile is selected. Auto: select through exCMConfigVdslRate and exCMConfigVdslSymmetry Manual: select through exCMConfigVdslProfile.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.9INTEGER {auto(0), manual(1)}read-writecurrent
exCMConfigVdslRole
OBJECT-TYPE
This object specifies the VDSL role: auto, local (CO), or remote (CPE).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.10INTEGER {auto(0), local(1), remote(2)}read-writecurrent
exCMConfigVdslRate
OBJECT-TYPE
This object specifies the VDSL rate/reach.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.11INTEGER {highSpeed(0), longRange(1)}read-writecurrent
exCMConfigVdslSymmetry
OBJECT-TYPE
This object specifies the VDSL band plan or symmetry.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.12INTEGER {asymmetric(0), symmetric(1)}read-writecurrent
exCMConfigVdslProfile
OBJECT-TYPE
This object specifies the VDSL profile.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.13INTEGER {profile1-AnnexA-R-POTS-D-32-EU-32-30a(1), profile2-AnnexA-R-POTS-D-32-EU-32-17a(2), profile3-AnnexA-R-POTS-D-32-EU-32-12b(3), profile4-AnnexA-R-POTS-D-32-EU-32-12a(4), profile5-AnnexA-R-POTS-D-32-EU-32-8a(5), profile6-AnnexA-R-POTS-D-32-EU-32-8b(6), profile7-AnnexA-R-POTS-D-32-EU-32-8c(7), profile8-AnnexA-R-POTS-D-32-EU-32-8d(8), profile9-AnnexA-R-POTS-D-64-EU-64-30a-NUS0(9), profile10-AnnexA-R-POTS-D-64-EU-64-17a(10), profile11-AnnexB-B7-3-997-M1x-M(11), profile12-AnnexB-B7-4-997-M2x-M-8(12), profile13-AnnexB-B7-5-997-M2x-A(13), profile14-AnnexB-B7-6-997-M2x-M(14), profile15-AnnexB-B7-9-997E17-M2x-A(15), profile16-AnnexB-B7-10-997E30-M2x-NUS0(16), profile17-AnnexB-B8-1-998-M1x-A(17), profile18-AnnexB-B8-2-998-M1x-B(18), profile19-AnnexB-B8-4-998-M2x-A(19), profile20-AnnexB-B8-5-998-M2x-M(20), profile21-AnnexB-B8-6-998-M2x-B(21), profile22-AnnexB-B8-8-998E17-M2x-NUS0(22), profile23-AnnexB-B8-9-998E17-M2x-NUS0-M(23), profile24-AnnexB-B8-10-998ADE17-M2x-NUS0-M(24), profile25-AnnexB-B8-11-998E17-M2x-A(25), profile26-AnnexB-B8-12-998E17-M2x-B(26), profile27-AnnexB-B8-13-998E30-M2x-NUS0(27), profile28-AnnexB-B8-14-998E30-M2x-NUS0-M(28), profile29-AnnexB-B8-15-998ADE30-M2x-NUS0-M(29), profile30-AnnexB-B8-16-998ADE30-M2x-NUS0-A(30), profile31-AnnexC-POTS-25-138-b(31), profile32-AnnexC-POTS-25-276-b(32), profile33-AnnexC-TMC-ISDN(33)}read-writecurrent
exCMConfigVdslOverrideProfile
OBJECT-TYPE
This object specifies whether to override advanced VDSL profile settings (e.g exCMConfigVdslSignalToNoiseRatioUp).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.14EnableDisableValueread-writecurrent
exCMConfigVdslSignalToNoiseRatioUp
OBJECT-TYPE
This object represents the advanced VDSL profile setting signal-to-noise ratio (upstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.15Integer32 (30..240)read-writecurrent
exCMConfigVdslMinDataRateUp
OBJECT-TYPE
This object represents the advanced VDSL profile setting minimum data rate (upstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.16Integer32 (128..101064)read-writecurrent
exCMConfigVdslMaxDataRateUp
OBJECT-TYPE
This object represents the advanced VDSL profile setting maximum data rate (upstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.17Integer32 (128..101064)read-writecurrent
exCMConfigVdslMaxInterleaveDelayUp
OBJECT-TYPE
This object represents the advanced VDSL profile setting maximum delay (upstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.18Integer32 (0..16)read-writecurrent
exCMConfigVdslMinInpUp
OBJECT-TYPE
This object represents the advanced VDSL profile setting minimum INP (impulse noise protection) (upstream).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.19Integer32 (1..18)read-writecurrent
exCMConfigVdslSignalToNoiseRatioDown
OBJECT-TYPE
This object represents the advanced VDSL profile setting signal-to-noise ratio (downstream) in 0.1 dB.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.20Integer32 (30..240)read-writecurrent
exCMConfigVdslMinDataRateDown
OBJECT-TYPE
This object represents the advanced VDSL profile setting minimum data rate (downstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.21Integer32 (128..101064)read-writecurrent
exCMConfigVdslMaxDataRateDown
OBJECT-TYPE
This object represents the advanced VDSL profile setting maximum data rate (downstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.22Integer32 (128..101064)read-writecurrent
exCMConfigVdslMaxInterleaveDelayDown
OBJECT-TYPE
This object represents the advanced VDSL profile setting maximum delay (downstream) in ms.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.23Integer32 (0..16)read-writecurrent
exCMConfigVdslMinInpDown
OBJECT-TYPE
This object represents the advanced VDSL profile setting minimum INP (impulse noise protection) (downstream).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.24Integer32 (1..18)read-writecurrent
exCMConfigVdslBitswapping
OBJECT-TYPE
This object represents the advanced VDSL profile setting bitswapping.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.25EnableDisableValueread-writecurrent
exCMConfigVdslLowBandwidthAlarmUp
OBJECT-TYPE
This object represents the VDSL low bandwidth alarm threshold (upstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.26Integer32 (0..90000)read-writecurrent
exCMConfigVdslLowBandwidthAlarmDown
OBJECT-TYPE
This object represents the VDSL low bandwidth alarm threshold (downstream) in kbps.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.27Integer32 (0..90000)read-writecurrent
exCMConfigEthernetPortName
OBJECT-TYPE
This object identifies a user definable name for the ethernet port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.28DisplayString (SIZE(0..8))read-writecurrent
exCMConfigEthernetPortEnable
OBJECT-TYPE
This object identifies whether the VDSL port is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.29YesNoValueread-writecurrent
exCMConfigEthernetAutoNegotiation
OBJECT-TYPE
This object identifies the whether ethernet auto-negotiation is enabled. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.30EnableDisableValueread-writecurrent
exCMConfigEthernetAutoNegAdv10HDX
OBJECT-TYPE
This object controls whether or the ethernet port advertises willingness to connect at 10Mbps, half duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.31YesNoValueread-writecurrent
exCMConfigEthernetAutoNegAdv10FDX
OBJECT-TYPE
This object controls whether or the ethernet port advertises willingness to connect at 10Mbps, full duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.32YesNoValueread-writecurrent
exCMConfigEthernetAutoNegAdv100HDX
OBJECT-TYPE
This object controls whether or the ethernet port advertises willingness to connect at 100Mbps, half duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.33YesNoValueread-writecurrent
exCMConfigEthernetAutoNegAdv100FDX
OBJECT-TYPE
This object controls whether or the ethernet port advertises willingness to connect at 100Mbps, full duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.34YesNoValueread-writecurrent
exCMConfigEthernetAutoNegAdv1000FDX
OBJECT-TYPE
This object controls whether or the ethernet port advertises willingness to connect at 1000Mbps, full duplex. This setting is ignored when auto-negotiation is disabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.35YesNoValueread-writecurrent
exCMConfigEthernetSpeed
OBJECT-TYPE
If ethernet auto-negotiation is disabled then this object identifies the configured cooper speed. 1000 Mbps speed can only be auto negotiated. If ethernet auto-negotiation is enabled then this object is ignored. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.36INTEGER {speed10Mbs(0), speed100Mbps(1)}read-writecurrent
exCMConfigEthernetDuplex
OBJECT-TYPE
If ethernet auto-negotiation is disabled then this object identifies the duplex setting for 10 & 100 Mbps for the ethernet port. Duplex for 1000 Mbps has to be auto negotiated. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.37INTEGER {full(0), half(1)}read-writecurrent
exCMConfigEthernetCrossOver
OBJECT-TYPE
This object identifies the ethernet MDI/MDI-X setting.This object is read-only if the media converter module's ConfigMode jumper is set to
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.38INTEGER {auto(0), mdi(1), mdix(2)}read-writecurrent
exCMConfigEthernetPauseEnh
OBJECT-TYPE
This object identifies the ethernet pause (flow control) setting that is a advertised. The settings can be disabled, advertise symmetrical, advertise asymmetrical TX or advertise symmetrical and asymmetrical RX. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.39INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), symmAsymRx(3)}read-writecurrent
exCMConfigEthernetAutoSpeedDownshift
OBJECT-TYPE
This object identifies the number of times the PHY attempts to establish a Gigabit link before the PHY downshift to the next highest speed. A value of 0 indicates the auto downshift is disabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.40INTEGER (0..8)read-writecurrent
exCMConfigEthernet10BaseTDistance
OBJECT-TYPE
When using cable exceeding 100 meters in 10BASE-T mode this feature should be set to extended(1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.41INTEGER {normal(0), extended(1)}read-writecurrent
exCMConfigUnidirectionalEthernet
OBJECT-TYPE
Restrict the flow of Ethernet traffic to a single direction. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.42INTEGER {notApplicable(-1), disabled(0), ethernetToVdsl(1), vdslToEthernet(2)}read-writecurrent
exCMConfigPriorityToEgressQueueMap0
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.43INTEGER (0..3)read-writecurrent
exCMConfigPriorityToEgressQueueMap1
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.44INTEGER (0..3)read-writecurrent
exCMConfigPriorityToEgressQueueMap2
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.45INTEGER (0..3)read-writecurrent
exCMConfigPriorityToEgressQueueMap3
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.46INTEGER (0..3)read-writecurrent
exCMConfigPriorityToEgressQueueMap4
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.47INTEGER (0..3)read-writecurrent
exCMConfigPriorityToEgressQueueMap5
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.48INTEGER (0..3)read-writecurrent
exCMConfigPriorityToEgressQueueMap6
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.49INTEGER (0..3)read-writecurrent
exCMConfigPriorityToEgressQueueMap7
OBJECT-TYPE
Set the egress queue of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.50INTEGER (0..3)read-writecurrent
exCMConfigEthernet8021pPriority
OBJECT-TYPE
Use 802.1p tag priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.51OnOffValueread-writecurrent
exCMConfigEthernetIpTosPriority
OBJECT-TYPE
Use IP TOS priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.52OnOffValueread-writecurrent
exCMConfigEthernetPriorityPrecedence
OBJECT-TYPE
Configure priority precedence. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.53INTEGER {notApplicable(-1), priority8021p(0), priorityIpTos(1)}read-writecurrent
exCMConfigEthernetCongestionPolicy
OBJECT-TYPE
Configure priority congestion policy. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.54INTEGER {notApplicable(-1), strict(0), weighted(1)}read-writecurrent
exCMConfigEthernetPriorityMap0
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.55INTEGER (0..7)read-writecurrent
exCMConfigEthernetPriorityMap1
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.56INTEGER (0..7)read-writecurrent
exCMConfigEthernetPriorityMap2
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.57INTEGER (0..7)read-writecurrent
exCMConfigEthernetPriorityMap3
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.58INTEGER (0..7)read-writecurrent
exCMConfigEthernetPriorityMap4
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.59INTEGER (0..7)read-writecurrent
exCMConfigEthernetPriorityMap5
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.60INTEGER (0..7)read-writecurrent
exCMConfigEthernetPriorityMap6
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.61INTEGER (0..7)read-writecurrent
exCMConfigEthernetPriorityMap7
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.62INTEGER (0..7)read-writecurrent
exCMConfigEthernetIngressLimit
OBJECT-TYPE
Set a limit on the rate of incoming packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.63INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26)}read-writecurrent
exCMConfigEthernetEgressLimit
OBJECT-TYPE
Set a limit on the rate of outgoing packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.64INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26)}read-writecurrent
exCMConfigEthernetDiscardTaggedFrames
OBJECT-TYPE
Enable discarding of tagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.65OnOffValueread-writecurrent
exCMConfigEthernetDiscardUntaggedFrames
OBJECT-TYPE
Enable discarding of untagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.66OnOffValueread-writecurrent
exCMConfigEthernetDefaultVlanId
OBJECT-TYPE
Set the default VLAN ID to insert when tagging frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.67INTEGER (0..4095)read-writecurrent
exCMConfigEthernetDefaultPriority
OBJECT-TYPE
Set the default frame priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.68INTEGER (0..7)read-writecurrent
exCMConfigEthernetVlanTaggingAction
OBJECT-TYPE
Set the default tagging action. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.69INTEGER {notApplicable(-1), none(0), untag(1), tag(2), doubleTag(3)}read-writecurrent
exCMConfigEthernetFilterUnknownMulticast
OBJECT-TYPE
Enable filtering of multicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.70OnOffValueread-writecurrent
exCMConfigEthernetFilterUnknownUnicast
OBJECT-TYPE
Enable filtering of unicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.71OnOffValueread-writecurrent
exCMConfigVdsl8021pPriority
OBJECT-TYPE
Use 802.1p tag priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.72OnOffValueread-writecurrent
exCMConfigVdslIpTosPriority
OBJECT-TYPE
Use IP TOS priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.73OnOffValueread-writecurrent
exCMConfigVdslPriorityPrecedence
OBJECT-TYPE
Configure priority precedence. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.74INTEGER {notApplicable(-1), priority8021p(0), priorityIpTos(1)}read-writecurrent
exCMConfigVdslCongestionPolicy
OBJECT-TYPE
Configure priority congestion policy. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.75INTEGER {notApplicable(-1), strict(0), weighted(1)}read-writecurrent
exCMConfigVdslPriorityMap0
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 0. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.76INTEGER (0..7)read-writecurrent
exCMConfigVdslPriorityMap1
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 1. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.77INTEGER (0..7)read-writecurrent
exCMConfigVdslPriorityMap2
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 2. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.78INTEGER (0..7)read-writecurrent
exCMConfigVdslPriorityMap3
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 3. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.79INTEGER (0..7)read-writecurrent
exCMConfigVdslPriorityMap4
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 4. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.80INTEGER (0..7)read-writecurrent
exCMConfigVdslPriorityMap5
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 5. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.81INTEGER (0..7)read-writecurrent
exCMConfigVdslPriorityMap6
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 6. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.82INTEGER (0..7)read-writecurrent
exCMConfigVdslPriorityMap7
OBJECT-TYPE
Change the priority of frames tagged with 802.1p priority 7. A value of -1 signifies that this feature is not supported by the current media converter module firmware. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.83INTEGER (0..7)read-writecurrent
exCMConfigVdslIngressLimit
OBJECT-TYPE
Set a limit on the rate of incoming packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.84INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26)}read-writecurrent
exCMConfigVdslEgressLimit
OBJECT-TYPE
Set a limit on the rate of outgoing packets. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.85INTEGER {notApplicable(-1), rateUnlimited(0), rate64kbps(1), rate128kbps(2), rate192kbps(3), rate256kbps(4), rate320kbps(5), rate384kbps(6), rate512kbps(7), rate768kbps(8), rate1mbps(9), rate2mbps(10), rate3mbps(11), rate4mbps(12), rate5mbps(13), rate6mbps(14), rate7mbps(15), rate8mbps(16), rate9mbps(17), rate10mbps(18), rate20mbps(19), rate30mbps(20), rate40mbps(21), rate50mbps(22), rate60mbps(23), rate70mbps(24), rate80mbps(25), rate90mbps(26)}read-writecurrent
exCMConfigVdslDiscardTaggedFrames
OBJECT-TYPE
Enable discarding of tagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.86OnOffValueread-writecurrent
exCMConfigVdslDiscardUntaggedFrames
OBJECT-TYPE
Enable discarding of untagged frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.87OnOffValueread-writecurrent
exCMConfigVdslDefaultVlanId
OBJECT-TYPE
Set the default VLAN ID to insert when tagging frames. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.88INTEGER (0..4095)read-writecurrent
exCMConfigVdslDefaultPriority
OBJECT-TYPE
Set the default frame priority. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.89INTEGER (0..7)read-writecurrent
exCMConfigVdslVlanTaggingAction
OBJECT-TYPE
Set the default tagging action. (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.90INTEGER {notApplicable(-1), none(0), untag(1), tag(2), doubleTag(3)}read-writecurrent
exCMConfigVdslFilterUnknownMulticast
OBJECT-TYPE
Enable filtering of multicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.91OnOffValueread-writecurrent
exCMConfigVdslFilterUnknownUnicast
OBJECT-TYPE
Enable filtering of unicast frames with an unknown destination (This feature may require a media converter module firmware upgrade).
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.92OnOffValueread-writecurrent
exCMConfigVdslFastMode
OBJECT-TYPE
This object represents the VDSL fast mode setting.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.2.1.93EnableDisableValueread-writecurrent
exCMLedTable
OBJECT-TYPE
Table of CM-1110 type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.3not-accessiblecurrent
exCMLedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.3.1not-accessiblecurrent
exCMLedSlotIndex
OBJECT-TYPE
The Slot number of the module
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.3.1.2SlotNumbernot-accessiblecurrent
exCMLedILNK
OBJECT-TYPE
This object identifies the status of the ILNK (InterLink) LED on the media converter module. Possible status values are: slowBlinkingGreen(1) - ILNK port is idle or handshaking fastBlinkingGreen(2) - ILNK port is training green(3) - ILNK port is up
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.3.1.3INTEGER {off(0), slowBlinkingGreen(1), fastBlinkingGreen(2), green(3)}read-onlycurrent
exCMLedLOC
OBJECT-TYPE
This object identifies the status of the Local (LOC) LED on the media converter module. When this LED is green, it indicates that the InterLink port's VDSL role is local.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.3.1.4INTEGER {off(0), green(1)}read-onlycurrent
exCMLedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - InterLink loopback enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.3.1.5INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
exCMLedETH
OBJECT-TYPE
This object identifies the status of the ETH (Ethernet) LED on the media converter module. Possible status values are: off(0) - ETH port is down slowBlinkingGreen(1) - ETH port is down, due to the VDSL port or peer copper ethernet port being down green(2) - ETH port is up
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.3.1.6INTEGER {off(0), slowBlinkingGreen(1), green(2)}read-onlycurrent
exCMLedRMT
OBJECT-TYPE
This object identifies the status of the Remote (RMT) LED on the media converter module. When this LED is green, it indicates that the InterLink port's VDSL role is remote.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.3.1.7INTEGER {off(0), green(1)}read-onlycurrent
exCMStatsTable
OBJECT-TYPE
Table of CM-1110 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4not-accessiblecurrent
exCMStatsEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1not-accessiblecurrent
exCMStatsSlotIndex
OBJECT-TYPE
The Slot number the ex-1CM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.2SlotNumbernot-accessiblecurrent
exCMMediaPortIndex
OBJECT-TYPE
Media converter module port index indicating which media port the statistical counters are associated with.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.3INTEGER (1..2)not-accessiblecurrent
exCMPortInDiscards
OBJECT-TYPE
A counter that counts the number of good, non-filtered frames that normally would have been forwarded, but could not due to lack of buffer space.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.4Counter32read-onlycurrent
exCMPortInFiltered
OBJECT-TYPE
A counter that counts the number of good frames that were filtered due to ingress switch policy rules.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.5INTEGER (0..65535)read-onlycurrent
exCMPortInGoodOctets
OBJECT-TYPE
An ingress counter that is the sum of lengths of all good Ethernet frames received on the media port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.6Counter32read-onlycurrent
exCMPortHCInGoodOctets
OBJECT-TYPE
An ingress counter that is the sum of lengths of all good Ethernet frames received on the media port. This object is a 64-bit version of exCMPortInGoodOctets.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.7Counter64read-onlycurrent
exCMPortInBadOctets
OBJECT-TYPE
An ingress counter that is the sum of lengths of all bad Ethernet frames received on the media port..
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.8Counter32read-onlycurrent
exCMPortInUnicasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Unicast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.9Counter32read-onlycurrent
exCMPortInBroadcasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Broadcast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.10Counter32read-onlycurrent
exCMPortInMulticasts
OBJECT-TYPE
An ingress counter that counts the number of good frames received that have a Multicast destination MAC address. This count does not include frames counted in the exCMPortInPauses or the exCMPortInBroadcasts objects.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.11Counter32read-onlycurrent
exCMPortInPauses
OBJECT-TYPE
An ingress counter that counts the number of good frames reachieved that have a Pause destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.12Counter32read-onlycurrent
exCMPortInUnderSizes
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length less that 64 octets but with a valid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.13Counter32read-onlycurrent
exCMPortInFragments
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length less that 64 octets and an invalid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.14Counter32read-onlycurrent
exCMPortInOversizes
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length more than the maximum packet size but with a valid FCS. The maximum packet size can be set using the exCMConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.15Counter32read-onlycurrent
exCMPortInJabbers
OBJECT-TYPE
An ingress counter that counts the number of frames received with a length more than the maximum packet size but with a invalid FCS. The maximum packet size can be set using the exCMConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.16Counter32read-onlycurrent
exCMPortInRxErrs
OBJECT-TYPE
An ingress counter that counts the number of frames received with an RxErr signal from the PHY.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.17Counter32read-onlycurrent
exCMPortInFcsErrs
OBJECT-TYPE
An ingress counter that counts the number of frames received with a CRC error not counted in the exCMPortInFragments, exCMPortInFcsErr, or the exCMPortInRxErr objects.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.18Counter32read-onlycurrent
exCMPortPkts64Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of exactly 64 Octets, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.19Counter32read-onlycurrent
exCMPortPkts65to127Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 65 and 127 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.20Counter32read-onlycurrent
exCMPortPkts128to255Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 128 and 255 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.21Counter32read-onlycurrent
exCMPortPkts256to511Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 256 and 511 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.22Counter32read-onlycurrent
exCMPortPkts512to1023Octets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 512 and 1023 Octets inclusive, including those with errors.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.23Counter32read-onlycurrent
exCMPortPkts1024toMaxOctets
OBJECT-TYPE
A Histogram counter that counts the number of frames received and transmitted with a length of between 1024 and maximum packet size octets inclusive, including those with errors. The maximum packet size can be set using the exCMConfigMaxPacketsSize object.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.24Counter32read-onlycurrent
exCMPortOutOctets
OBJECT-TYPE
An Egress counter that is the sum of lengths of all good Ethernet frames sent on the media port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.25Counter32read-onlycurrent
exCMPortHCOutOctets
OBJECT-TYPE
An Egress counter that is the sum of lengths of all good Ethernet frames sent on the media port. This object is a 64-bit version of exCMPortOutOctets.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.26Counter64read-onlycurrent
exCMPortOutFiltered
OBJECT-TYPE
A counter that counts the number of good frames that were filtered due to egress switch policy rules.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.27INTEGER (0..65535)read-onlycurrent
exCMPortOutUnicasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Unicast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.28Counter32read-onlycurrent
exCMPortOutBroadcasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Broadcast destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.29Counter32read-onlycurrent
exCMPortOutMulticasts
OBJECT-TYPE
An Egress counter that counts the number of good frames sent that have a Multicast destination MAC address. This count does not include frames counted in the exCMPortOutPauses or the exCMPortOutBroadcasts objects.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.30Counter32read-onlycurrent
exCMPortOutPauses
OBJECT-TYPE
An Egress counter that counts the number of good frames reachieved that have a Pause destination MAC address.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.31Counter32read-onlycurrent
exCMPortDeferreds
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced no collisions but are delayed because the medium was busy during the first attempt. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.32Counter32read-onlycurrent
exCMPortCollisions
OBJECT-TYPE
An Egress counter that counts the number of collision events seen by the MAC not including those counted in exCMPortSingles, exCMPortMultiple , exCMPortExcessives or exCMPortLates objects. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.33Counter32read-onlycurrent
exCMPortSingles
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced exactly one collision. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.34Counter32read-onlycurrent
exCMPortMultiples
OBJECT-TYPE
An Egress counter that counts the number of successfully transmitted frames that experienced more than one collision. This counter is aplicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.35Counter32read-onlycurrent
exCMPortExcessives
OBJECT-TYPE
An Egress counter that counts the number frames dropped in the transmit MAC because the frame experienced 16 consecutive collisions. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.36Counter32read-onlycurrent
exCMPortLates
OBJECT-TYPE
An Egress counter that counts the number times a collision is detected later than 512 bits-times into the transmission of a frame. This counter is applicable in half-duplex only.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.37Counter32read-onlycurrent
exCMPortOutFcsErrs
OBJECT-TYPE
An Egress counter that counts the number frames transmitted with an invalid FCS.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.38Counter32read-onlycurrent
exCMPortResetCounters
OBJECT-TYPE
Allows the resetting of all exCMStats statistical counters for this port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.4.1.39YesNoValueread-writecurrent
exCMVdslStatsTable
OBJECT-TYPE
Table of CM-1110 type media converter module's configuration and status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5not-accessiblecurrent
exCMVdslStatsEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-1110 type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1not-accessiblecurrent
exCMVdslStatsSlotIndex
OBJECT-TYPE
The Slot number the ex-1CM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.2SlotNumbernot-accessiblecurrent
exCMVdslStatsMediaPortIndex
OBJECT-TYPE
Media converter module port index indicating which media port the statistical counters are associated with.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.3Unsigned32not-accessiblecurrent
exCMVdslStatsTimePeriod
OBJECT-TYPE
Media converter module port index indicating which media port the statistical counters are associated with.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.4INTEGER {sinceLinkup(1), current15Minutes(2), previous15Minutes(3), current24Hours(4), previous24Hours(5)}read-onlycurrent
exCMVdslStatsFullInitLocal
OBJECT-TYPE
The VDSL port's fully initialized (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.5Integer32read-onlycurrent
exCMVdslStatsCodeViolationLocal
OBJECT-TYPE
The VDSL port's code violation (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.6Integer32read-onlycurrent
exCMVdslStatsCorrectedLocal
OBJECT-TYPE
The VDSL port's corrected (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.7Integer32read-onlycurrent
exCMVdslStatsFecSecsLocal
OBJECT-TYPE
The VDSL port's forward error correction seconds (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.8Integer32read-onlycurrent
exCMVdslStatsErroredSecsLocal
OBJECT-TYPE
The VDSL port's errored seconds (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.9Integer32read-onlycurrent
exCMVdslStatsSeverelyErroredSecsLocal
OBJECT-TYPE
The VDSL port's severely errored seconds (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.10Integer32read-onlycurrent
exCMVdslStatsLossOfSignalSecsLocal
OBJECT-TYPE
The VDSL port's loss of signal seconds (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.11Integer32read-onlycurrent
exCMVdslStatsUnavailableSecsLocal
OBJECT-TYPE
The VDSL port's unavailable seconds (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.12Integer32read-onlycurrent
exCMVdslStatsTimeElapsedLocal
OBJECT-TYPE
The VDSL port's elapsed time in seconds (local) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.13Integer32read-onlycurrent
exCMVdslStatsFullInitRemote
OBJECT-TYPE
The VDSL port's fully initialized (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.14Integer32read-onlycurrent
exCMVdslStatsCodeViolationRemote
OBJECT-TYPE
The VDSL port's code violation (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.15Integer32read-onlycurrent
exCMVdslStatsCorrectedRemote
OBJECT-TYPE
The VDSL port's corrected (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.16Integer32read-onlycurrent
exCMVdslStatsFecSecsRemote
OBJECT-TYPE
The VDSL port's forward error correction seconds (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.17Integer32read-onlycurrent
exCMVdslStatsErroredSecsRemote
OBJECT-TYPE
The VDSL port's errored seconds (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.18Integer32read-onlycurrent
exCMVdslStatsSeverelyErroredSecsRemote
OBJECT-TYPE
The VDSL port's severely errored seconds (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.19Integer32read-onlycurrent
exCMVdslStatsLossOfSignalSecsRemote
OBJECT-TYPE
The VDSL port's loss of signal seconds (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.20Integer32read-onlycurrent
exCMVdslStatsUnavailableSecsRemote
OBJECT-TYPE
The VDSL port's unavailable seconds (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.21Integer32read-onlycurrent
exCMVdslStatsTimeElapsedRemote
OBJECT-TYPE
The VDSL port's elapsed time in seconds (remote) count.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.5.1.22Integer32read-onlycurrent
exCMAvctTable
OBJECT-TYPE
Table of ex-CM media converter modules.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6not-accessiblecurrent
exCMAvctEntry
OBJECT-TYPE
Entries of the table, each relating to a copper Ethernet port on the eX-CM type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1not-accessiblecurrent
exCMAvctSlotIndex
OBJECT-TYPE
The Slot number the eX-CM type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.2SlotNumbernot-accessiblecurrent
exCMAvctStart
OBJECT-TYPE
Set this self-clearing variable to yes initiate the Advanced Virtual Cable Test. Note: During the test, no network data will be passed.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.3YesNoValueread-writecurrent
exCMAvctStatus
OBJECT-TYPE
This object identifies the state of the Advanced Virtual Cable Tester.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.4INTEGER {notStarted(0), inProgress(1), testComplete(2)}read-onlycurrent
exCMAvctTxRxPair1Results
OBJECT-TYPE
Test result code returned from Virtual Cable Test of the Tx/Rx pair one.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.5INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
exCMAvctTxRxPair1Amplitude
OBJECT-TYPE
Amplitude of Tx/Rx pair one in millivolts when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.6DisplayString (SIZE(0..20))read-onlycurrent
exCMAvctTxRxPair1Distance
OBJECT-TYPE
Distance in meters to fault when test result codes for Tx/Rx pair one is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.7DisplayString (SIZE(0..20))read-onlycurrent
exCMAvctTxRxPair2Results
OBJECT-TYPE
Test result code returned from Virtual Cable Test of the Tx/Rx pair two.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.8INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
exCMAvctTxRxPair2Amplitude
OBJECT-TYPE
Amplitude of Tx/Rx pair two in millivolts when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.9DisplayString (SIZE(0..20))read-onlycurrent
exCMAvctTxRxPair2Distance
OBJECT-TYPE
Distance in meters to fault when test result codes for Tx/Rx pair two is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.10DisplayString (SIZE(0..20))read-onlycurrent
exCMAvctTxRxPair3Results
OBJECT-TYPE
Test result code returned from Virtual Cable Test of the Tx/Rx pair three.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.11INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
exCMAvctTxRxPair3Amplitude
OBJECT-TYPE
Amplitude of Tx/Rx pair three in millivolts when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.12DisplayString (SIZE(0..20))read-onlycurrent
exCMAvctTxRxPair3Distance
OBJECT-TYPE
Distance in meters to fault when test result codes for Tx/Rx pair three is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.13DisplayString (SIZE(0..20))read-onlycurrent
exCMAvctTxRxPair4Results
OBJECT-TYPE
Test result code returned from Virtual Cable Test of Tx/Rx pair four.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.14INTEGER {normal(0), shortDetected(1), openDetected(2), testFailed(3)}read-onlycurrent
exCMAvctTxRxPair4Amplitude
OBJECT-TYPE
Amplitude of Tx/Rx pair four in millivolts when test result codes is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.15DisplayString (SIZE(0..20))read-onlycurrent
exCMAvctTxRxPair4Distance
OBJECT-TYPE
Distance in meters to fault when test result codes for Tx/Rx pair four is short or open.
1.3.6.1.4.1.1966.21.1.1.1.1.4.9.6.1.16DisplayString (SIZE(0..20))read-onlycurrent
cm10gt
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.10
cm10gtTable
OBJECT-TYPE
Table of CM-10G type media converter module's status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1not-accessiblecurrent
cm10gtEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-10G type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1not-accessiblecurrent
cm10gtSlotIndex
OBJECT-TYPE
The Slot number the CM-10G type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.2SlotNumbernot-accessiblecurrent
cm10gtModelname
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.3DisplayStringread-onlycurrent
cm10gtModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.4DisplayStringread-onlycurrent
cm10gtHwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware jumper J5 on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media converter module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm10gtHwSw1OperationMode
OBJECT-TYPE
Media converter module's current switch setting for operation mode. Data mode is for normal data transmission.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.6INTEGER {test(0), data(1)}read-onlycurrent
cm10gtHwSw2LinkMode
OBJECT-TYPE
Media converter module's current switch setting for Link Mode. If the Operation switch is set to Test, then this object indicates whether the port is in loopback or performing the build in link-test.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.7INTEGER {swDownSmartLinkPassthrough(0), swUpStandard(1)}read-onlycurrent
cm10gtHwSw3FiberFaultAlert
OBJECT-TYPE
Media converter module's current switch setting for Fiber Fault Alert. If the Operation switch is set to Test, then this object indicates which port is in test mode
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.8INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm10gtHwSw4EnergyEfficentEthernet
OBJECT-TYPE
This object indicates the current switch setting for Energy Efficient Ethernet on port 2.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.9INTEGER {disabled(0), enabled(1)}read-onlycurrent
cm10gtHwSw5Unused
OBJECT-TYPE
This object indicates the current switch setting for dip switch 5, which is unused.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.10INTEGER {disabled(0), enabled(1)}read-onlycurrent
cm10gtPort1LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.11INTEGER {down(0), up(1), shutdown(2)}read-onlycurrent
cm10gtPort1ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.12INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6), xfp(7), sfpPlus(8)}read-onlycurrent
cm10gtPort1AutoNegState
OBJECT-TYPE
Media converter module's current fiber auto-negotiation state (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.13INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm10gtPort1Speed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.14INTEGER {speed10Mbps(0), speed100Mbps(1), speed1000Mbps(2), speed10Gbps(3)}read-onlycurrent
cm10gtPort1Duplex
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.15INTEGER {half(0), full(1)}read-onlycurrent
cm10gtPort1PauseEnh
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.16INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm10gtPort1ReceiveStatus
OBJECT-TYPE
This object identifies the status of whether light is being received on the fiber port (port 1)
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.17INTEGER {fault(0), ok(1)}read-onlycurrent
cm10gtPort1LPRFStatus
OBJECT-TYPE
Media converter module's Link Partner Remote Fault status (port 1). This object only applies to SFP modules running at 1G, with auto-negotiation enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.18INTEGER {notApplicable(-1), ok(0), offline(1), linkFault(2), autoNegError(3)}read-onlycurrent
cm10gtPort2LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.19INTEGER {down(0), up(1), shutdown(2)}read-onlycurrent
cm10gtPort2ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.20INTEGER {rj45(4)}read-onlycurrent
cm10gtPort2AutoNegState
OBJECT-TYPE
Media converter module's current fiber auto-negotiation state (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.21INTEGER {disabled(0), complete(1), inProgress(2)}read-onlycurrent
cm10gtPort2Speed
OBJECT-TYPE
Media converter module's fiber port speed in megabits per second (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.22INTEGER {speed10Mbps(0), speed100Mbps(1), speed1000Mbps(2), speed10Gbps(3)}read-onlycurrent
cm10gtPort2Duplex
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated duplex setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.23INTEGER {half(0), full(1)}read-onlycurrent
cm10gtPort2PauseEnh
OBJECT-TYPE
If fiber auto-negotiation state is complete then this object indicates the media converter module's current fiber auto-negotiated pause setting. If auto-negotiation is not complete then the value returned should be ignored. (Port 2)
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.24INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
cm10gtPort2LPRFStatus
OBJECT-TYPE
Media converter module's copper Link Partner Remote Fault status.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.25INTEGER {ok(0), remoteFault(1)}read-onlycurrent
cm10gtPortLoopBack
OBJECT-TYPE
Media converter module's current port loopback mode setting. Writing to this object will change the current settings. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.26INTEGER {disabled(0), port1(1), port2(2)}read-writecurrent
cm10gtPortTestMode
OBJECT-TYPE
Media converter module's current port test mode setting.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.1.1.27INTEGER {disabled(0), port1(1)}read-onlycurrent
cm10gtConfigTable
OBJECT-TYPE
Table of CM-10G type media converter module's configuration type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2not-accessiblecurrent
cm10gtConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-10G type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1not-accessiblecurrent
cm10gtConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-10G type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.2SlotNumbernot-accessiblecurrent
cm10gtConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.3ContainerStatusread-writecurrent
cm10gtConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm10gtConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.5INTEGER {standard(0), smartLinkPassthrough(1)}read-writecurrent
cm10gtConfigFiberFaultAlert
OBJECT-TYPE
This object identifies the Fiber Fault Alert setting for the media module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.6EnableDisableValueread-writecurrent
cm10gtConfigFiberAutoNeg
OBJECT-TYPE
This object identifies the wither fiber auto-negotiation is enabled for both ports. This only applies if 1G SFP modules are in use. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.7EnableDisableValueread-writecurrent
cm10gtConfigPort1Name
OBJECT-TYPE
This object identifies a user definable name for port 1.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.8DisplayString (SIZE(0..8))read-writecurrent
cm10gtConfigPort1Enable
OBJECT-TYPE
This object identifies whether port 1 is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.9YesNoValueread-writecurrent
cm10gtConfigPort1FecEnable
OBJECT-TYPE
This object identifies the whether FEC control is enabled for this port. This config option only applies for an XFP module. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.10YesNoValueread-writecurrent
cm10gtConfigPort1FecAmplitude
OBJECT-TYPE
This object identifies the FEC Amplitude value for this port. This config option only applies for an XFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.11INTEGER (-128..127)read-writecurrent
cm10gtConfigPort1FecPhase
OBJECT-TYPE
This object identifies the FEC phase value for this port. This config option only applies for an XFP module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.12INTEGER (-128..127)read-writecurrent
cm10gtConfigPort1WavelengthEnable
OBJECT-TYPE
This object identifies whether Wavelength fine tuning is enabled for this port. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.13YesNoValueread-writecurrent
cm10gtConfigPort1WavelengthValue
OBJECT-TYPE
This object identifies Wavelength fine tuning value for this port. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.14INTEGER (0..65535)read-writecurrent
cm10gtConfigPort1ChannelEnable
OBJECT-TYPE
This object identifies whether channel number fine tuning is enabled for this port. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.15YesNoValueread-writecurrent
cm10gtConfigPort1ChannelNumber
OBJECT-TYPE
This object identifies the channel number fine tuning value for this port. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.16INTEGER (1..65535)read-writecurrent
cm10gtConfigPort1TxDitherEnable
OBJECT-TYPE
This object identifies the whether TX Dither control is enabled on this port. If not enabled the default TX Dither value will be used. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.17YesNoValueread-writecurrent
cm10gtConfigPort1TxDitherValue
OBJECT-TYPE
This object identifies the whether TX Dither is enabled for this port. This object is read-only if the media module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.18EnableDisableValueread-writecurrent
cm10gtConfigPort2Name
OBJECT-TYPE
This object identifies a user definable name for port 2.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.19DisplayString (SIZE(0..8))read-writecurrent
cm10gtConfigPort2Enable
OBJECT-TYPE
This object identifies whether port 2 is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.20YesNoValueread-writecurrent
cm10gtConfigPort2CopperDuplex
OBJECT-TYPE
This object identifies the duplex settings for the copper port.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.21INTEGER {half(1), auto(2)}read-writecurrent
cm10gtConfigPort2CopperPauseEnh
OBJECT-TYPE
This object identifies the copper pause (flow control) setting that is a advertised. The settings can be disabled, advertise symmetrical, advertise asymmetrical TX or advertise symmetrical and asymmetrical RX.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.22INTEGER {disabled(0), symmetrical(1), asymmetricalTx(2), symmAsymRx(3)}read-writecurrent
cm10gtConfigPort2CopperEnergyEfficientEthernet
OBJECT-TYPE
This object identifies the copper Energy-Efficient Ethernet setting for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.2.1.23OnOffValueread-writecurrent
cm10gtLedTable
OBJECT-TYPE
Table of CM-10G type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.3not-accessiblecurrent
cm10gtLedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-10G type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.3.1not-accessiblecurrent
cm10gtLedsSlotIndex
OBJECT-TYPE
The Slot number the CM-10G type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.3.1.2SlotNumberread-onlycurrent
cm10gtLedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Loopback or Link-Test enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm10gtLedLK1
OBJECT-TYPE
This object identifies the status of the port 1 link (LK1) LED on the media converter module. Possible status values are: off(0) - No link on(1) - Port link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.3.1.4INTEGER {off(0), on(1)}read-onlycurrent
cm10gtLedLK2
OBJECT-TYPE
This object identifies the status of the port 2 link (LK2) LED on the media converter module. Possible status values are: off(0) - No link on(1) - Port link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.10.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
cm4gpt
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.1.4.11
cm4gptTable
OBJECT-TYPE
Table of CM-4GPT type media converter module's status type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1not-accessiblecurrent
cm4gptEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-4GPT type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1not-accessiblecurrent
cm4gptSlotIndex
OBJECT-TYPE
The Slot number the CM-4GPT type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.2SlotNumbernot-accessiblecurrent
cm4gptModelname
OBJECT-TYPE
This object identifies the model of media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.3DisplayStringread-onlycurrent
cm4gptModelDesc
OBJECT-TYPE
This object identifies a static description of the media converter module present in the chassis
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.4DisplayStringread-onlycurrent
cm4gptHwJmp5ConfigMode
OBJECT-TYPE
This object identifies the media converter module's ConfigMode, set by hardware jumper J5 on the media converter module. When this object is set to hardwareSwitches(0), the media converter module will disable configuration control from the management module's software and all configuration control comes from the media converter module's hardware switches or jumpers.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.5INTEGER {hardwareSwitches(0), auto(1)}read-onlycurrent
cm4gptHwSw1LinkMode
OBJECT-TYPE
Media converter module's current switch setting for Link Mode.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.6INTEGER {swDownSmartLinkPassthrough(0), swUpStandard(1)}read-onlycurrent
cm4gptHwSw2FiberFaultAlert
OBJECT-TYPE
Media converter module's current switch setting for Fiber Fault Alert.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.7INTEGER {swDownDisabled(0), swUpEnabled(1)}read-onlycurrent
cm4gptHwSw3RateSelect
OBJECT-TYPE
Media converter module's current switch setting for Rate Select.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.8INTEGER {swDownLow(0), swUpHigh(1)}read-onlycurrent
cm4gptHwSw4Unused
OBJECT-TYPE
This object indicates the current switch setting for the 4th, unused switch.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.9INTEGER {disabled(0), enabled(1)}read-onlycurrent
cm4gptPort1LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.10INTEGER {down(0), up(1)}read-onlycurrent
cm4gptPort1ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 1).
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.11INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6), xfp(7), sfpPlus(8)}read-onlycurrent
cm4gptPort2LinkStatus
OBJECT-TYPE
Media converter module's current fiber link status (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.12INTEGER {down(0), up(1)}read-onlycurrent
cm4gptPort2ConnType
OBJECT-TYPE
Media converter module's fiber port connector type (port 2).
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.1.1.13INTEGER {sc(0), lc(1), st(2), sfp(3), fc(5), mtrj(6), xfp(7), sfpPlus(8)}read-onlycurrent
cm4gptConfigTable
OBJECT-TYPE
Table of CM-4GPT type media converter module's configuration type information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2not-accessiblecurrent
cm4gptConfigEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-4GPT type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1not-accessiblecurrent
cm4gptConfigSlotIndex
OBJECT-TYPE
The Slot number the CM-4GPT type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.2SlotNumbernot-accessiblecurrent
cm4gptConfigStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module, verified and and saved to flash. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.3ContainerStatusread-writecurrent
cm4gptConfigModuleName
OBJECT-TYPE
This object identifies a user configurable name for the media converter module present in the chassis.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.4DisplayString (SIZE(0..63))read-writecurrent
cm4gptConfigLinkMode
OBJECT-TYPE
This object identifies the Link Mode for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.5INTEGER {standard(0), smartLinkPassthrough(1)}read-writecurrent
cm4gptConfigFiberFaultAlert
OBJECT-TYPE
This object identifies the Fiber Fault Alert setting for the media module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.6EnableDisableValueread-writecurrent
cm4gptConfigRateSelect
OBJECT-TYPE
This object identifies the Rate Select setting for the media converter module. This object is read-only if the media converter module's ConfigMode jumper is set to hardwareSwitches(0).
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.7INTEGER {low(0), high(1)}read-writecurrent
cm4gptConfigPort1Name
OBJECT-TYPE
This object identifies a user definable name for port 1.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.8DisplayString (SIZE(0..8))read-writecurrent
cm4gptConfigPort1Enable
OBJECT-TYPE
This object identifies whether port 1 is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.9YesNoValueread-writecurrent
cm4gptConfigPort2Name
OBJECT-TYPE
This object identifies a user definable name for port 2.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.10DisplayString (SIZE(0..8))read-writecurrent
cm4gptConfigPort2Enable
OBJECT-TYPE
This object identifies whether port 2 is enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.2.1.11YesNoValueread-writecurrent
cm4gptLedTable
OBJECT-TYPE
Table of CM-4GPT type media converter module's LED status information.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.3not-accessiblecurrent
cm4gptLedEntry
OBJECT-TYPE
Entries of the table, each relating to a separate CM-4GPT type media converter module.
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.3.1not-accessiblecurrent
cm4gptLedsSlotIndex
OBJECT-TYPE
The Slot number the CM-4GPT type module is currently inserted
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.3.1.2SlotNumbernot-accessiblecurrent
cm4gptLedPWR
OBJECT-TYPE
This object identifies the status of the power (PWR) LED on the media converter module. Possible status values are: off(0) - No power to the module onGreen(1) - Power being applied to module blinking(2) - Loopback or Link-Test enabled
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.3.1.3INTEGER {off(0), onGreen(1), blinking(2)}read-onlycurrent
cm4gptLedLK1
OBJECT-TYPE
This object identifies the status of the port 1 link (LK1) LED on the media converter module. Possible status values are: off(0) - No link on(1) - Port link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.3.1.4INTEGER {off(0), on(1)}read-onlycurrent
cm4gptLedLK2
OBJECT-TYPE
This object identifies the status of the port 2 link (LK2) LED on the media converter module. Possible status values are: off(0) - No link on(1) - Port link present
1.3.6.1.4.1.1966.21.1.1.1.1.4.11.3.1.5INTEGER {off(0), on(1)}read-onlycurrent
mcrSfpDmiModuleTable
OBJECT-TYPE
Table of SFP Diagnostic Monitoring Interface information for Optical Transceivers
1.3.6.1.4.1.1966.21.1.1.1.1.5not-accessiblecurrent
mcrSfpDmiModuleEntry
OBJECT-TYPE
Entries of the table, each relating to a separate SFP module.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1not-accessiblecurrent
sfpDmiSlotIndex
OBJECT-TYPE
The Slot number of the media converter module containing this SFP/XFP
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.2SlotNumbernot-accessiblecurrent
sfpDmiMediaPortIndex
OBJECT-TYPE
Media converter module port index.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.3Unsigned32not-accessiblecurrent
sfpDmiStatus
OBJECT-TYPE
This object identifies the status of the SFP module. If sfpCommFailed bit is set then the rest of the data in this entry is invalid
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.4Bits {sfpModuleInserted(24), sfpCommFailed(25), sfpDmiSupported(26)}read-onlycurrent
sfpDmiConnectorType
OBJECT-TYPE
This object identifies the SFP DMI connector type.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.5INTEGER {unknownUnspecified(0), sc(1), fiberChannelStyle1Copper(2), fiberChannelStyle2Copper(3), bncTnc(4), fiberChannelCoaxHeader(5), fiberJack(6), lc(7), mtrj(8), mu(9), sg(10), opticalPigtail(11), hssdcII(32), copperPigtail(33)}read-onlycurrent
sfpDmiNominalBitRate
OBJECT-TYPE
This object identifies the SFP DMI nominal bit rate of fiber interface, in megabits per second.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.6Unsigned32read-onlycurrent
sfpDmiLinkReach9125
OBJECT-TYPE
This object identifies the SFP DMI maximum length in meters of media supported by the fiber transceiver for 9 micron (125 micron jacket) single-mode fiber.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.7Integer32read-onlycurrent
sfpDmiLinkReach50125
OBJECT-TYPE
This object identifies the SFP DMI maximum length in meters of media supported by the fiber transceiver for 50 micron (125 micron jacket) multi-mode fiber.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.8Integer32read-onlycurrent
sfpDmiLinkReach625125
OBJECT-TYPE
This object identifies the SFP DMI maximum length in meters of media supported by the fiber transceiver for 62.5 micron (125 micron jacket) multi-mode fiber.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.9Integer32read-onlycurrent
sfpDmiFiberWaveLength
OBJECT-TYPE
This object identifies the wavelength of the fiber interface's optical transceiver, in nanometers.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.10Unsigned32read-onlycurrent
sfpDmiCurrentTempState
OBJECT-TYPE
This object identifies the current alarm status for SFP DMI internally measured temperature.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.11INTEGER {invalid(0), notSupported(1), normal(2), highWarn(3), highAlarm(4), lowWarn(5), lowAlarm(6)}read-onlycurrent
sfpDmiRealTimeTemp
OBJECT-TYPE
This object identifies the SFP DMI real time temperature. The value displayed will be either Celsius or Fahrenheit based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.12DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighTempWarn
OBJECT-TYPE
This object identifies the SFP DMI high temperature warning threshold. The value displayed will be either Celsius or Fahrenheit based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.13DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighTempAlarm
OBJECT-TYPE
This object identifies the SFP DMI high temperature warning threshold. The value displayed will be either Celsius or Fahrenheit based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.14DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowTempWarn
OBJECT-TYPE
This object identifies the SFP DMI high temperature warning threshold. The value displayed will be either Celsius or Fahrenheit based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.15DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowTempAlarm
OBJECT-TYPE
This object identifies the SFP DMI high temperature warning threshold. The value displayed will be either Celsius or Fahrenheit based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.16DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiCurrentVoltState
OBJECT-TYPE
This object identifies current alarm status for SFP DMI internally measured voltage.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.17INTEGER {invalid(0), notSupported(1), normal(2), highWarn(3), highAlarm(4), lowWarn(5), lowAlarm(6)}read-onlycurrent
sfpDmiRealTimeVolt
OBJECT-TYPE
This object identifies the SFP DMI real time voltage in Volts.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.18DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighVoltWarn
OBJECT-TYPE
This object identifies the SFP DMI high voltage warning threshold in Volts
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.19DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighVoltAlarm
OBJECT-TYPE
This object identifies the SFP DMI high voltage warning threshold in Volts
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.20DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowVoltWarn
OBJECT-TYPE
This object identifies the SFP DMI high voltage warning threshold in Volts
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.21DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowVoltAlarm
OBJECT-TYPE
This object identifies the SFP DMI high voltage warning threshold in Volts
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.22DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiCurrentTxBiasState
OBJECT-TYPE
This object identifies current alarm status for SFP DMI internally measured transmit bias current in milliamps.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.23INTEGER {invalid(0), notSupported(1), normal(2), highWarn(3), highAlarm(4), lowWarn(5), lowAlarm(6)}read-onlycurrent
sfpDmiRealTimeTxBias
OBJECT-TYPE
This object identifies the SFP DMI high TX Bias current in milliamps.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.24DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighTxBiasWarn
OBJECT-TYPE
This object identifies the SFP DMI high TX Bias current warning threshold in milliamps.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.25DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighTxBiasAlarm
OBJECT-TYPE
This object identifies the SFP DMI high TX Bias current alarm threshold in milliamps.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.26DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowTxBiasWarn
OBJECT-TYPE
This object identifies the SFP DMI low TX Bias current warning threshold in milliamps.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.27DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowTxBiasAlarm
OBJECT-TYPE
This object identifies the SFP DMI low TX Bias current alarm threshold in milliamps.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.28DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiCurrentTxPowerState
OBJECT-TYPE
This object identifies current alarm status for SFP DMI internally measured transmit power.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.29INTEGER {invalid(0), notSupported(1), normal(2), highWarn(3), highAlarm(4), lowWarn(5), lowAlarm(6)}read-onlycurrent
sfpDmiRealTimeTxPower
OBJECT-TYPE
This object identifies the SFP DMI real time TX output power. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.30DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighTxPowerWarn
OBJECT-TYPE
This object identifies the SFP DMI high TX output power warning threshold. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.31DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighTxPowerAlarm
OBJECT-TYPE
This object identifies the SFP DMI high TX output power alarm threshold. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.32DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowTxPowerWarn
OBJECT-TYPE
This object identifies the SFP DMI low TX output power warning threshold. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.33DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowTxPowerAlarm
OBJECT-TYPE
This object identifies the SFP DMI low TX output power alarm threshold. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.34DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiCurrentRxPowerState
OBJECT-TYPE
This object identifies current alarm status for SFP DMI internally measured receive power.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.35INTEGER {invalid(0), notSupported(1), normal(2), highWarn(3), highAlarm(4), lowWarn(5), lowAlarm(6)}read-onlycurrent
sfpDmiRealTimeRxPower
OBJECT-TYPE
This object identifies the SFP DMI real time RX received optical power. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.36DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighRxPowerWarn
OBJECT-TYPE
This object identifies the SFP DMI high RX received optical warning threshold. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.37DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiHighRxPowerAlarm
OBJECT-TYPE
This object identifies the SFP DMI high RX received optical alarm threshold. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.38DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowRxPowerWarn
OBJECT-TYPE
This object identifies the SFP DMI low RX received optical warning threshold. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.39DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiLowRxPowerAlarm
OBJECT-TYPE
This object identifies the SFP DMI low RX received optical alarm threshold. The value displayed will be either millwatts or Dbm based on your current regional display settings.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.40DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiStatus2
OBJECT-TYPE
This object identifies the status of the SFP module. If sfpCommFailed value is set then the rest of the data in this entry is invalid 0x80 - sfpModuleInserted 0x40 - sfpCommFailed 0x20 - sfpDmiSupported
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.41Unsigned32read-onlycurrent
sfpDmiVendorSerialNumber
OBJECT-TYPE
This object identifies the SFP DMI serial number.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.42DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiVendorName
OBJECT-TYPE
This object identifies the SFP DMI serial number.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.43DisplayString (SIZE(0..32))read-onlycurrent
sfpDmiVendorPartNumber
OBJECT-TYPE
This object identifies the SFP DMI serial number.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.44DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiAux1Type
OBJECT-TYPE
This object identifies the type of value that is being measured by the Auxillary 1 registers on the XFP
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.45INTEGER {notSupported(0), apdBiasVoltmv(1), tecCurrentma(3), laserTemperature(4), laserWavelength(5), p5Voltv(6), p33Voltv(7), p18Voltv(8), m52Voltv(9), p5vCurrentma(10), p33vCurrentma(13), p18vCurrentma(14), m52vCurrentma(15)}read-onlycurrent
xfpDmiAux1State
OBJECT-TYPE
This object identifies current alarm status for the XFP Aux1 registers
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.46INTEGER {invalid(0), notSupported(1), normal(2), highWarn(3), highAlarm(4), lowWarn(5), lowAlarm(6)}read-onlycurrent
xfpDmiRealTimeAux1
OBJECT-TYPE
This object identifies the XFP DMI real time values for the Aux1 registers
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.47DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiHighAux1Warn
OBJECT-TYPE
This object identifies the XFP DMI high warning threshold for Aux1
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.48DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiHighAux1Alarm
OBJECT-TYPE
This object identifies the XFP DMI alarm alarm threshold for Aux1
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.49DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiLowAux1Warn
OBJECT-TYPE
This object identifies the XFP DMI low warning threshold for Aux1
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.50DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiLowAux1Alarm
OBJECT-TYPE
This object identifies the XFP DMI low alarm threshold for Aux1
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.51DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiAux2Type
OBJECT-TYPE
This object identifies the type of value that is being measured by the Auxillary 1 registers on the XFP
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.52INTEGER {notSupported(0), apdBiasVoltmv(1), tecCurrentma(3), laserTemperature(4), laserWavelength(5), p5Voltv(6), p33Voltv(7), p18Voltv(8), m52Voltv(9), p5vCurrentma(10), p33vCurrentma(13), p18vCurrentma(14), m52vCurrentma(15)}read-onlycurrent
xfpDmiAux2State
OBJECT-TYPE
This object identifies current alarm status for the XFP Aux2 registers
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.53INTEGER {invalid(0), notSupported(1), normal(2), highWarn(3), highAlarm(4), lowWarn(5), lowAlarm(6)}read-onlycurrent
xfpDmiRealTimeAux2
OBJECT-TYPE
This object identifies the SFP DMI real time values for the Aux2 registers
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.54DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiHighAux2Warn
OBJECT-TYPE
This object identifies the XFP DMI high warning threshold for Aux2
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.55DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiHighAux2Alarm
OBJECT-TYPE
This object identifies the XFP DMI alarm alarm threshold for Aux2
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.56DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiLowAux2Warn
OBJECT-TYPE
This object identifies the XFP DMI low warning threshold for Aux2
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.57DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiLowAux2Alarm
OBJECT-TYPE
This object identifies the XFP DMI low alarm threshold for Aux2
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.58DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiMinBitRate
OBJECT-TYPE
This object specifies the XFP minimum bit rate.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.59Integer32read-onlycurrent
xfpDmiMaxBitRate
OBJECT-TYPE
This object specifies the XFP maximum bit rate.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.60Integer32read-onlycurrent
xfpDmiReachEBW50125
OBJECT-TYPE
This object specifies the link length that is supported by the fiber transceiver using extended bandwidth 50 micron core (125 micron jacket) multimode fiber
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.61Integer32read-onlycurrent
sfpDmiReachCopper
OBJECT-TYPE
This object identifies the maximum length in meters that is supported by the SFP/XFP interface using copper cable.
1.3.6.1.4.1.1966.21.1.1.1.1.5.1.62Integer32read-onlycurrent
mcrAlarmsWarningsTable
OBJECT-TYPE
Table of outstanding alarms and warnings.
1.3.6.1.4.1.1966.21.1.1.1.1.6not-accessiblecurrent
mcrAlarmsWarningsEntry
OBJECT-TYPE
Entries of the table, each relating to a separate alarm or warning.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1not-accessiblecurrent
alarmWarnSequenceIndex
OBJECT-TYPE
This object identifies the sequence in which the alarms or warnings were generated. Gaps in the sequence numbers are normal.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.2Unsigned32not-accessiblecurrent
alarmWarnType
OBJECT-TYPE
This object identifies the alert/Trap number associated with this alarm/warning.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.3Unsigned32read-onlycurrent
alarmWarnSeverity
OBJECT-TYPE
This object identifies the severity level of the alarm/warning. Value will be one of the top three levels.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.4Unsigned32read-onlycurrent
alarmWarnFlags
OBJECT-TYPE
This object identifies the flags defining the alarm/warning. 0x00000002 - chassis type alert 0x00000004 - Power Supply Monitoring Unit type alert 0x00000008 - PSMU power supply type alert 0x00000010 - PSMU fan type alert 0x00000020 - Management module type alert 0x00000040 - Media converter module type alert 0x00000080 - Media converter module SFP module type alert.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.5Unsigned32read-onlycurrent
alarmWarnChassisNum
OBJECT-TYPE
This object identifies the chassis number associated with this alarm/warning.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.6Unsigned32read-onlycurrent
alarmWarnDeviceNum
OBJECT-TYPE
This object identifies the Hardware slot/bay location of the hardware associated with this alarm or warning. - 0 indicates alarm/warning occurred on the chassis backplane. - If AlarmWarnFlags indicates a power supply then this value the power supply bay number. - Otherwise it is the chassis slot number.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.7Unsigned32read-onlycurrent
alarmWarnTimeStamp
OBJECT-TYPE
This object identifies the time stamp of when the alarm/warning was reported. (in seconds since the Epoch, defined as 0:00:00 UTC on the morning of January 1, 1970), that the alert was reported on the MCR-MGT.)
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.8TimeTicksread-onlycurrent
alarmWarnMessage
OBJECT-TYPE
This object identifies the alarm/warning message string which will contain any values of bound variables.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.9DisplayStringread-onlycurrent
alarmWarnPortNum
OBJECT-TYPE
This object identifies the location of the media port associated with this alarm or warning.
1.3.6.1.4.1.1966.21.1.1.1.1.6.1.10Unsigned32read-onlycurrent
mcrMediaPortTable
OBJECT-TYPE
Table of general port status information.
1.3.6.1.4.1.1966.21.1.1.1.1.7not-accessiblecurrent
mcrMediaPortEntry
OBJECT-TYPE
Entries of the table, each relating to a separate media converter module port.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1not-accessiblecurrent
mediaPortSlotIndex
OBJECT-TYPE
Slot number for the media converter module containing this port.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.2Unsigned32not-accessiblecurrent
mediaPortPortIndex
OBJECT-TYPE
Port number on media card. Valid values are 1 to the highest number of ports available on a media card. There are usually two ports
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.3Unsigned32not-accessiblecurrent
moduleModel
OBJECT-TYPE
This object identifies the model name of the module containing this port.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.4DisplayStringread-onlycurrent
portName
OBJECT-TYPE
This object identifies the name configured for this port.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.5DisplayStringread-onlycurrent
portEnable
OBJECT-TYPE
This object indicates whether the port has been enabled.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.6INTEGER {disabled(0), enable(1)}read-onlycurrent
portType
OBJECT-TYPE
The type of port (copper, fiber, etc.) .
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.7INTEGER {copper(0), fiber(1), sfp(2), xfp(3), sfpPlus(4)}read-onlycurrent
portLinkStatus
OBJECT-TYPE
The port's current link status.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.8INTEGER {down(0), up(1), shutdown(2)}read-onlycurrent
portConnType
OBJECT-TYPE
The port's connector type
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.9INTEGER {rj45(0), sc(1), lc(2), st(3), sfp(4), fc(5), mtrj(6), xfp(7), sfpPlus(8)}read-onlycurrent
portAutoNegState
OBJECT-TYPE
The port's auto-negotiation state
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.10INTEGER {notApplicable(-1), disabled(0), complete(1), inProgress(2)}read-onlycurrent
portSpeed
OBJECT-TYPE
If the port auto-negotiation state is complete then this object indicates the ports current auto-negotiated speed setting. If auto-negotiation is not complete then the value returned should be ignored
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.11INTEGER {notApplicable(-1), speed10Mbs(0), speed100Mbps(1), speed1000Mbps(2), speed10Gbps(3)}read-onlycurrent
portDuplex
OBJECT-TYPE
If port auto-negotiation state is complete then this object indicates the media converter module's current auto-negotiated duplex setting for this port. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.12INTEGER {notApplicable(-1), half(0), full(1)}read-onlycurrent
portPause
OBJECT-TYPE
If port auto-negotiation state is complete then this object indicates the media converter module's current auto-negotiated pause setting for this port. If auto-negotiation is not complete then the value returned should be ignored.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.13INTEGER {notApplicable(-1), disabled(0), symmetrical(1), asymmetricalTx(2), asymmetricalRx(3)}read-onlycurrent
portRemoteStatus
OBJECT-TYPE
This port's Link Partner Remote Fault status or Far End Fault status
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.14INTEGER {notApplicable(-1), ok(0), remoteFault(1), offline(2), linkFault(3), autoNegError(4), disable(5), receivingFEF(6), sendingFEF(7)}read-onlycurrent
portMediaType
OBJECT-TYPE
The type of port (copper, fiber, etc.) .
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.15INTEGER {unknown(-1), copper(0), fiber(1)}read-onlycurrent
portPhysicalProtocol
OBJECT-TYPE
The physical networking protocol used by the port.
1.3.6.1.4.1.1966.21.1.1.1.1.7.1.16INTEGER {unknown(0), ethernet(1), vdsl(2)}read-onlycurrent
mcrManagementGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2
mgtNetworkGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.1
systemGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.1.1
systemStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.1ContainerStatusread-writecurrent
systemName
OBJECT-TYPE
The name of the system management module.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.2DisplayString (SIZE(1..63))read-writecurrent
systemDomainName
OBJECT-TYPE
The domain name of the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.3DisplayString (SIZE(0..32))read-writecurrent
systemIpAddress
OBJECT-TYPE
The management module's unique IPv4 network IP address. If you are using the management module in an IPv6 network, this field can be left blank.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.4IpAddressread-writecurrent
systemSubnetBits
OBJECT-TYPE
The number of bits in the subnet mask. For example, a subnet mask of 255.255.0.0 has 16 subnet/prefix bits. Valid values are 0-32. The default is 0. When the value is 0, the correct value is determined based on the class of the IP Address.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.5Integer32 (0..32)read-writecurrent
systemDHCPUpdateDNS
OBJECT-TYPE
If enabled, the DNS system will be updated after the management module gets the IP address via DHCP.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.6OnOffValueread-writecurrent
systemAutoObtainDNS
OBJECT-TYPE
If on, the DNS server IP address will be obtained automatically automatically via DHCP.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.7OnOffValueread-writecurrent
systemAutoObtainGW
OBJECT-TYPE
If enabled, the default gateway IP address will be get automatically via DHCP.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.8OnOffValueread-writecurrent
systemDomainPrefix
OBJECT-TYPE
The domain prefix for primary Ethernet interface of the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.9DisplayString (SIZE(0..7))read-writecurrent
systemTFTPRetry
OBJECT-TYPE
The number of times the management module will attempt to transfer (using TFTP) a file to/from a host. Default is 5. A value of 0 (zero) means that the management module will not attempt a retry should TFTP fail.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.10Integer32 (0..5)read-writecurrent
systemTFTPTimeOut
OBJECT-TYPE
The time, in seconds, that the management module will wait for a successful transmit or receipt of TFTP packets before retrying a TFTP transfer. Default is 3 seconds.
1.3.6.1.4.1.1966.21.1.1.1.2.1.1.11Integer32 (3..10)read-writecurrent
gatewayTable
OBJECT-TYPE
Table of configured gateway.
1.3.6.1.4.1.1966.21.1.1.1.2.1.2not-accessiblecurrent
gatewayEntry
OBJECT-TYPE
Entries of the table, each relating to a separate configured gateway.
1.3.6.1.4.1.1966.21.1.1.1.2.1.2.1not-accessiblecurrent
gatewayIndex
OBJECT-TYPE
gatewayIndex
1.3.6.1.4.1.1966.21.1.1.1.2.1.2.1.1GenericTableIndexnot-accessiblecurrent
gatewayStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.2.1.2ContainerStatusread-writecurrent
gatewayHost
OBJECT-TYPE
You can specify up to twenty hosts to act as gateways in your network. Each gateway host must be defined in the management module host table.
1.3.6.1.4.1.1966.21.1.1.1.2.1.2.1.3DisplayString (SIZE(0..14))read-writecurrent
gatewayType
OBJECT-TYPE
Specify the type of gateway: Default-A gateway which provides general access beyond your local network. Host-A gateway reserved for accessing a specific host external to your local network. Network-A gateway reserved for accessing a specific network external to your local network.
1.3.6.1.4.1.1966.21.1.1.1.2.1.2.1.4INTEGER {host(0), network(1), default(2)}read-writecurrent
gatewayIpAddress
OBJECT-TYPE
When the gateway is a Host or Network gateway, you must specify the IP address of the target host machine/network.
1.3.6.1.4.1.1966.21.1.1.1.2.1.2.1.5Ipv4v6Addressread-writecurrent
gatewaySubnetBits
OBJECT-TYPE
When the gateway is a Network gateway, you must specify the subnet/prefix bits for that network. If the IP address is IPv4, then the Subnet/Prefix Bits range is 0-32. If the IP address is IPv6, then the Subnet/Prefix Bits range is 0-128.
1.3.6.1.4.1.1966.21.1.1.1.2.1.2.1.6Integer32 (0..128)read-writecurrent
gatewayInterface
OBJECT-TYPE
The interface that the management module is going to use to access the Remote Host.
1.3.6.1.4.1.1966.21.1.1.1.2.1.2.1.7DisplayString (SIZE(0..20))read-writecurrent
hostTable
OBJECT-TYPE
The hosts Group table.
1.3.6.1.4.1.1966.21.1.1.1.2.1.3not-accessiblecurrent
hostEntry
OBJECT-TYPE
An entry in the host table, each relating to a separate host.
1.3.6.1.4.1.1966.21.1.1.1.2.1.3.1not-accessiblecurrent
hostIndex
OBJECT-TYPE
The table entry number for this host.
1.3.6.1.4.1.1966.21.1.1.1.2.1.3.1.1GenericTableIndexnot-accessiblecurrent
hostStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.3.1.2ContainerStatusread-writecurrent
hostName
OBJECT-TYPE
The host name used for this host entry. To delete an entry, blank out this field. If blank, this entry is currently unused.
1.3.6.1.4.1.1966.21.1.1.1.2.1.3.1.3DisplayString (SIZE(0..14))read-writecurrent
hostIpAddr
OBJECT-TYPE
The host IP address used for this entry.
1.3.6.1.4.1.1966.21.1.1.1.2.1.3.1.4Ipv4v6Addressread-writecurrent
hostFqdn
OBJECT-TYPE
The host full qualified domain name for the host entry. If blank, this entry is currently unused.
1.3.6.1.4.1.1966.21.1.1.1.2.1.3.1.5DisplayString (SIZE(0..255))read-writecurrent
dnsTable
OBJECT-TYPE
Table of DNS hosts
1.3.6.1.4.1.1966.21.1.1.1.2.1.4not-accessiblecurrent
dnsEntry
OBJECT-TYPE
Entries of the table, each relating to a separate DNS host.
1.3.6.1.4.1.1966.21.1.1.1.2.1.4.1not-accessiblecurrent
dnsIndex
OBJECT-TYPE
DNS host index
1.3.6.1.4.1.1966.21.1.1.1.2.1.4.1.1GenericTableIndexnot-accessiblecurrent
dnsStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.4.1.2ContainerStatusread-writecurrent
dnsIpAddress
OBJECT-TYPE
You can specify the IP addresses for up to two DNS (Domain Name Servers) hosts in your network. The first DNS entry in the list is the primary DNS and the second DNS entry is the secondary server.
1.3.6.1.4.1.1966.21.1.1.1.2.1.4.1.3Ipv4v6Addressread-writecurrent
dnsActive
OBJECT-TYPE
Activates/deactivates a DNS entry.
1.3.6.1.4.1.1966.21.1.1.1.2.1.4.1.4OnOffValueread-writecurrent
dynamicDNSGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.1.5
dynamicDNSStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.1ContainerStatusread-writecurrent
dynamicDNS
OBJECT-TYPE
Enable/disable dynamic DNS.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.2OnOffValueread-writecurrent
dynamicDNSHostname
OBJECT-TYPE
Host name.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.3DisplayString (SIZE(1..14))read-writecurrent
dynamicDNSUserName
OBJECT-TYPE
User name.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.4DisplayString (SIZE(1..16))read-writecurrent
dynamicDNSPassword
OBJECT-TYPE
This object identifies the dynamic DNS password. Reading of this object will always return a blank string
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.5DisplayString (SIZE(1..16))read-writecurrent
dynamicDNSSystemType
OBJECT-TYPE
System type.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.6INTEGER {dynamic(0), static(1), custom(2)}read-writecurrent
dynamicDNSWildCard
OBJECT-TYPE
Specifies whether to add a alias such as * to your registered host name.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.7INTEGER {enable(0), disable(1), nochange(2)}read-writecurrent
dynamicDNSConnectionMethod
OBJECT-TYPE
Specifies how the management module is going to connection to the DynDNS.org server.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.8INTEGER {http(0), httpport8245(1), https(2)}read-writecurrent
dynamicDNSSSLVerifyPeerCertificate
OBJECT-TYPE
Enable this option when you want the Validation Criteria to match the Peer Certificate for authentication to pass. If you enable this option, you need to download an SSL/TLS certificate authority (CA) list file to the management module. Any values that are entered in the validation criteria must match the peer certificate for an SSL connection; any fields left blank will not be validated against the peer certificate.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.9OnOffValueread-writecurrent
dynamicDNSSSLCountry
OBJECT-TYPE
A two character country code; for example, US.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.10DisplayString (SIZE(0..2))read-writecurrent
dynamicDNSSSLStateProv
OBJECT-TYPE
Up to a 128 character entry for the state/province; for example, IL.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.11DisplayString (SIZE(0..128))read-writecurrent
dynamicDNSSSLLocality
OBJECT-TYPE
Up to a 128 character entry for the location; for example, a city.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.12DisplayString (SIZE(0..128))read-writecurrent
dynamicDNSSSLOrganisation
OBJECT-TYPE
Up to a 64 character entry for the organization; for example, Accounting.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.13DisplayString (SIZE(0..64))read-writecurrent
dynamicDNSSSLOrganisationUnit
OBJECT-TYPE
Up to a 64 character entry for the unit in the organization; for example, Payroll.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.14DisplayString (SIZE(0..64))read-writecurrent
dynamicDNSSSLCommonName
OBJECT-TYPE
Up to a 64 character entry for common name; for example, the host name or fully qualified domain name.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.15DisplayString (SIZE(0..64))read-writecurrent
dynamicDNSSSLEmail
OBJECT-TYPE
Up to a 64 character entry for an email address; for example, acct@anycompany.com.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.16DisplayString (SIZE(0..128))read-writecurrent
dynamicDNSStatusString
OBJECT-TYPE
Dynamic DNS statistics
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.17OCTET STRING (SIZE(0..1024))read-onlycurrent
dynamicDNSSSLCipherTable
OBJECT-TYPE
SSL Cipher.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18not-accessiblecurrent
dynamicDNSSSLCipherEntry
OBJECT-TYPE
An entry in the dynamicDNSSSLCipherTable, each relating to a cipher entry.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18.1not-accessiblecurrent
dynamicDNSSSLCipherPriority
OBJECT-TYPE
The cipher priority. 1- highest 5 - lowest.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18.1.1Integer32 (1..5)not-accessiblecurrent
dynamicDNSSSLCipherStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18.1.2ContainerStatusread-writecurrent
dynamicDNSSSLCipherEncryption
OBJECT-TYPE
SSL Encryption. None is not allowed for priority 1. Any will use the first encryption format that can be negotiated. The default is any.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18.1.3INTEGER {none(0), any(1), aes(2), tripledes(3), des(4), arctwo(5), arcfour(6)}read-writecurrent
dynamicDNSSSLCipherKeySizeMin
OBJECT-TYPE
The minimum key size value that will be used for the specified encryption type. The default is 40.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18.1.4INTEGER {min40(0), min56(1), min64(2), min128(3), min168(4), min256(5)}read-writecurrent
dynamicDNSSSLCipherKeySizeMax
OBJECT-TYPE
The maximum key size value that will be used for the specified encryption type. The default is 256.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18.1.5INTEGER {max40(0), max56(1), max64(2), max128(3), max168(4), max256(5)}read-writecurrent
dynamicDNSSSLCipherKeyExchange
OBJECT-TYPE
The type of key to exchange for the encryption format: Any-Any key exchange that is valid is used (this does not, however, include ADH keys). RSA-This is an RSA key exchange using an RSA key and certificate. EDHRSA-This is an EDH key exchange using an RSA key and certificate. EDHDSS-This is an EDH key exchange using a DSA key and certificate. ADH-This is an anonymous key exchange which does not require a private key or certificate. Choose this key if you do not want to authenticate the peer device, but you want the data encrypted on the SSL/TLS connection. The default is Any.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18.1.6INTEGER {any(0), rsa(1), edhrsa(2), edhdss(3), adh(4)}read-writecurrent
dynamicDNSSSLCipherHMAC
OBJECT-TYPE
Select the key-hashing for message authentication method for your encryption type: Any, MD5, or SHA1. The default is Any.
1.3.6.1.4.1.1966.21.1.1.1.2.1.5.18.1.7INTEGER {any(0), sha(1), md5(2)}read-writecurrent
ipv6Group
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.1.6
ipv6ServicesGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.1
ipv6serviceStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.1.1ContainerStatusread-writecurrent
serviceAutoDiscovery
OBJECT-TYPE
When on, the management module will send out a Router Solicitation message. If a Router Advertisement message is received, the management module will configure the IPv6 address(es) and configuration parameters based on the information contained in the advertisement. If no Router Advertisement message is received, the management module will attempt to connect to a DHCPv6 server to obtain IPv6 addresses and other configuration parameters. Default on.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.1.2OnOffValueread-writecurrent
serviceDHCPv6
OBJECT-TYPE
When on, requests IPv6 address(es) and configuration information from the DHCPv6 server. Default off.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.1.3OnOffValueread-writecurrent
serviceDHCPv6IPAddresses
OBJECT-TYPE
When on, the management module will accept IPv6 address(es) from the DHCPv6 server.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.1.4OnOffValueread-writecurrent
serviceDHCPv6NetworkPrefix
OBJECT-TYPE
When on, the management module will accept the network prefix from the DHCPv6 server.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.1.5OnOffValueread-writecurrent
serviceDHCPv6AutoObtainDNS
OBJECT-TYPE
If on, the DNS server IP address will be obtained automatically automatically via DHCP.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.1.6OnOffValueread-writecurrent
ipv6AddressTable
OBJECT-TYPE
IPv6 custom address table.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.2not-accessiblecurrent
ipv6AddressEntry
OBJECT-TYPE
IPv6 custom entry.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.2.1not-accessiblecurrent
ipv6AddressIndex
OBJECT-TYPE
Custom IPv6 address index.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.2.1.1GenericTableIndexnot-accessiblecurrent
ipv6AddressStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.2.1.2ContainerStatusread-writecurrent
ipv6AddressAddr
OBJECT-TYPE
Either enter a network prefix that the Device Server will use to derive an IPv6 address using the Device Server's MAC address (must turn ipv6AddressAuto1 on) or enter a specific IPv6 address.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.2.1.3Ipv4v6Addressread-writecurrent
ipv6AddressPrefixBits
OBJECT-TYPE
The IPv6 prefix bits of either the network or IPv6 address.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.2.1.4Integer32 (0..128)read-writecurrent
ipv6AddressAuto
OBJECT-TYPE
When on, the management module will derive an IPv6 address from the entered network prefix and the management module's MAC address.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.2.1.5OnOffValueread-writecurrent
ipv6AddressSendAdvertise
OBJECT-TYPE
When on, the management module will include the IPv6 address in router advertisements.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.2.1.6OnOffValueread-writecurrent
interfacev6StatsTable
OBJECT-TYPE
The interface IPv6 Group table.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.3not-accessiblecurrent
interfacev6StatsEntry
OBJECT-TYPE
An entry in the interface IPv6 table
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.3.1not-accessiblecurrent
interfacev6Index
OBJECT-TYPE
The IPv6 interface index.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.3.1.1GenericTableIndexnot-accessiblecurrent
interfacev6Name
OBJECT-TYPE
The IPv6 interface name.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.3.1.2DisplayStringread-onlycurrent
interfacev6Address
OBJECT-TYPE
The IPv6 interface IP address.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.3.1.3DisplayStringread-onlycurrent
interfacev6PrefixBits
OBJECT-TYPE
The IPv6 interface Prefix bits
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.3.1.4Integer32 (0..128)read-onlycurrent
interfacev6Scope
OBJECT-TYPE
The IPv6 interface scope.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.3.1.5INTEGER {global(0), host(1), link(2), site(3), compatv4(4), unknown(5)}read-onlycurrent
ipv6TunnelTable
OBJECT-TYPE
IPv6 tunnel table.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.4not-accessiblecurrent
ipv6TunnelEntry
OBJECT-TYPE
IPv6 tunnel entry.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.4.1not-accessiblecurrent
ipv6TunnelIndex
OBJECT-TYPE
The IPv6 tunnel index.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.4.1.1GenericTableIndexnot-accessiblecurrent
ipv6TunnelStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.4.1.2ContainerStatusread-writecurrent
ipv6TunnelName
OBJECT-TYPE
The name of the IPv6 tunnel. Maximum 16 alphanumeric characters.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.4.1.3DisplayStringread-writecurrent
ipv6TunnelMode
OBJECT-TYPE
The method or protocol that is used to create the IPv6 tunnel. o Manual-When specified, the management module will manually create the IPv6 tunnel to the specified Remote Host through the specified Interface. o ip6to4-When specified, the MCR-MGT will broadcast to the multicast address 192.88.99.1 through the specified Interface. When the closest ip6to4 router responds, it will create the IPv6 tunnel, encapsulating and decapsulating IPv6 traffic sent to and from the management module. o Teredo-When specified, the Teredo protocol encapsulates the IPv6 packet as an IPv4 UDP message, allowing it to pass through most network address translator (NAT) boxes and create an IPv6 tunnel to the specified Remote Host (a Teredo server) through the specified Interface. Default is Manual.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.4.1.4INTEGER {manual(0), ip6to4(1), teredo(2)}read-writecurrent
ipv6TunnelRemoteHost
OBJECT-TYPE
The IPv4 host that can access the IPv6 network when the Mode is Manual. The Teredo server when the Mode is Teredo.
1.3.6.1.4.1.1966.21.1.1.1.2.1.6.4.1.5DisplayStringread-writecurrent
mgtAccessGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.2
mgtAcessServicesGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.2.1
accessServicesStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.1ContainerStatusread-writecurrent
accessServicesSessInactTimeout
OBJECT-TYPE
The amount of time, in seconds, that the management session inactivity timer will run. When the timer expires, becuase no activity on the management session within the specified time, the management module will reset the management session. A value of 0 (zero), means that the inactivity timer will not expire (the session is open permanently, or until the user logs out).
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.2Integer32 (0..4294967)read-writecurrent
accessServiceHTTPD
OBJECT-TYPE
Turn on/off the HTTPD Service
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.3OnOffValueread-writecurrent
accessServiceHTTPSD
OBJECT-TYPE
Turn on/off the HTTPSD Service
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.4OnOffValueread-writecurrent
accessServiceTelnetD
OBJECT-TYPE
Turn on/off the TelnetD Service
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.5OnOffValueread-writecurrent
acessServiceSSHD
OBJECT-TYPE
Turn on/off the SSHD Service
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.6OnOffValueread-writecurrent
acessServiceSnmpD
OBJECT-TYPE
Turn on/off the SnmpD Service
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.7OnOffValueread-writecurrent
acessServiceSetIP
OBJECT-TYPE
Turn on/off the SetIP Service
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.8OnOffValueread-writecurrent
acessIncomingPings
OBJECT-TYPE
Allow incoming ping requests.
1.3.6.1.4.1.1966.21.1.1.1.2.2.1.9EnableDisableValueread-writecurrent
webManagerGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.2.2
webManagerStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.2.1ContainerStatusread-writecurrent
httpsPassphrase
OBJECT-TYPE
This object identifies the HTTPS SSL certificate passphrase. Reading of this object will always return a blank string
1.3.6.1.4.1.1966.21.1.1.1.2.2.2.2DisplayString (SIZE(1..16))read-writecurrent
sshServerGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.2.3
sshServerStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.1ContainerStatusread-writecurrent
sshServerAuthRSA
OBJECT-TYPE
When a client SSH session requests RSA authentication, the management module's SSH server will authenticate the user via RSA.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.2OnOffValueread-writecurrent
sshServerAuthDSA
OBJECT-TYPE
When a client SSH session requests DSA authentication, the management module's SSH server will authenticate the user via DSA
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.3OnOffValueread-writecurrent
sshServerAuthKeyboard
OBJECT-TYPE
The user types in a password for authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.4OnOffValueread-writecurrent
sshServerAuthPassword
OBJECT-TYPE
The user types in a password for authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.5OnOffValueread-writecurrent
sshServerCipher3Des
OBJECT-TYPE
The management module SSH server's 3DES encryption is enable/disabled.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.6OnOffValueread-writecurrent
sshServerCipherBlowfish
OBJECT-TYPE
The management module SSH server's Blowfish encryption is enabled/disabled.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.7OnOffValueread-writecurrent
sshServerCipherCipherAES
OBJECT-TYPE
The management module SSH server's AES encryption is enabled/disabled
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.8OnOffValueread-writecurrent
sshServerCipherCAST
OBJECT-TYPE
The management module SSH server's CAST encryption is enabled/disabled
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.9OnOffValueread-writecurrent
sshServerCipherArcfour
OBJECT-TYPE
The management module SSH server's Arcfour encryption is enabled/disabled.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.10OnOffValueread-writecurrent
sshServerVerbose
OBJECT-TYPE
Displays debug messages on the terminal.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.11OnOffValueread-writecurrent
sshServerCompression
OBJECT-TYPE
Requests compression of all data. Compression is desirable on slow connections, but will only slow down things on fast networks.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.12OnOffValueread-writecurrent
sshServerSSH1
OBJECT-TYPE
Enable/Disable SSH-1 on the server.
1.3.6.1.4.1.1966.21.1.1.1.2.2.3.13OnOffValueread-writecurrent
snmpAgentGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.2.4
snmpAgentStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.1ContainerStatusread-writecurrent
snmpContact
OBJECT-TYPE
The name and contract information of the person who manages this SMNP node.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.2DisplayString (SIZE(0..14))read-writecurrent
snmpLocation
OBJECT-TYPE
The physical location of the SNMP node.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.3DisplayString (SIZE(0..32))read-writecurrent
snmpCommunityTable
OBJECT-TYPE
Table of SNMP communities configured for the MCR-MGT agent
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.4not-accessiblecurrent
snmpCommunityEntry
OBJECT-TYPE
Entries of the table, each relating to a separate SNMP community definition
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.4.1not-accessiblecurrent
snmpCommunityIndex
OBJECT-TYPE
The MCR-MGT agent community index
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.4.1.1GenericTableIndexnot-accessiblecurrent
snmpCommunityStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.4.1.2ContainerStatusread-writecurrent
snmpCommunityName
OBJECT-TYPE
A name that will be sent to the management module from an SNMP manager. This name will define the permissions of the manager.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.4.1.3DisplayString (SIZE(0..14))read-writecurrent
snmpCommunityIpAddress
OBJECT-TYPE
The IP address of the SNMP manager that will send requests to the management module. If the address is 0.0.0.0, any SNMP manager with the Community Name can access the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.4.1.4Ipv4v6Addressread-writecurrent
snmpCommunityPermission
OBJECT-TYPE
Permits the management module to respond to SNMP requests by: None -There is no response to requests from SNMP. Readonly -Responds only to Read requests from SNMP. Readwrite -Responds to both Read and Write requests from SNMP.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.4.1.5INTEGER {none(0), readonly(1), readwrite(2)}read-writecurrent
snmpV3ReadOnlyUser
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.5
snmpV3ReadOnlyStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.5.1ContainerStatusread-writecurrent
snmpV3ReadOnlyUserName
OBJECT-TYPE
SNMP v3 read-only user name. This SNMP v3 user will have read-only S SNMP access permissions.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.5.2DisplayString (SIZE(0..16))read-writecurrent
snmpV3ReadOnlySecurityLevel
OBJECT-TYPE
Specifies the SNMP v3 read-only user security level.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.5.3INTEGER {none(0), authNoPriv(1), authPriv(2)}read-writecurrent
snmpV3ReadOnlyAuthAlgorithm
OBJECT-TYPE
Specifies the SNMP v3 read-only user authentication method.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.5.4INTEGER {md5(0), sha(1)}read-writecurrent
snmpV3ReadOnlyAuthPasswd
OBJECT-TYPE
Specifies the SNMP v3 read-only user authentication password.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.5.5DisplayString (SIZE(0..128))read-writecurrent
snmpV3ReadOnlyPrivacyAlgorithm
OBJECT-TYPE
Specifies the SNMP v3 read-only user privacy algorithm.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.5.6INTEGER {des(0), aes(1)}read-writecurrent
snmpV3ReadOnlyPrivacyPasswd
OBJECT-TYPE
Specifies the SNMP v3 read-only user privacy password.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.5.7DisplayString (SIZE(0..128))read-writecurrent
snmpV3ReadWriteUser
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.6
snmpV3ReadWriteStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.6.1ContainerStatusread-writecurrent
snmpV3ReadWriteUserName
OBJECT-TYPE
Specifies the SNMP v3 read-write user name. This SNMP v3 user will have read-write SNMP access permissions.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.6.2DisplayString (SIZE(0..16))read-writecurrent
snmpV3ReadWriteSecurityLevel
OBJECT-TYPE
Specifies the SNMP v3 read-write user security level.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.6.3INTEGER {none(0), authNoPriv(1), authPriv(2)}read-writecurrent
snmpV3ReadWriteAuthAlgorithm
OBJECT-TYPE
Specifies the SNMP v3 read-write user authentication method.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.6.4INTEGER {md5(0), sha(1)}read-writecurrent
snmpV3ReadWriteAuthPasswd
OBJECT-TYPE
Specifies the SNMP v3 read-write user authentication password.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.6.5DisplayString (SIZE(0..128))read-writecurrent
snmpV3ReadWritePrivacyAlgorithm
OBJECT-TYPE
Specifies the SNMP v3 read-write user privacy algorithm.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.6.6INTEGER {des(0), aes(1)}read-writecurrent
snmpV3ReadWritePrivacyPasswd
OBJECT-TYPE
Specifies the SNMP v3 read-write user privacy password.
1.3.6.1.4.1.1966.21.1.1.1.2.2.4.6.7DisplayString (SIZE(0..128))read-writecurrent
authorizedHostGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.2.5
authHostsStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.1ContainerStatusread-writecurrent
authHostOnly
OBJECT-TYPE
Determines whether only authorized hosts are allowed to access the management module. If set to yes then the management module will only respond to, and allow access to and from, the IP or MAC addresses of hosts configured in the authorized IP and MAC hosts tables.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.2YesNoValueread-writecurrent
authIpHostTable
OBJECT-TYPE
The hosts Group table.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.3not-accessiblecurrent
authIpHostEntry
OBJECT-TYPE
An entry in the AuthIpHostTable, each relating to a IP host.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.3.1not-accessiblecurrent
authHostIpIndex
OBJECT-TYPE
The table entry number for this host.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.3.1.1GenericTableIndexnot-accessiblecurrent
authHostIpStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.3.1.2ContainerStatusread-writecurrent
authHostIpAddr
OBJECT-TYPE
The host IP address used for this entry.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.3.1.3Ipv4v6Addressread-writecurrent
authHostIpDescr
OBJECT-TYPE
The host IP entry description.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.3.1.4DisplayString (SIZE(0..21))read-writecurrent
authMacHostTable
OBJECT-TYPE
The hosts Group table.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.4not-accessiblecurrent
authMacHostEntry
OBJECT-TYPE
An entry in the AuthIpHostTable, each relating to a host.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.4.1not-accessiblecurrent
authHostMacIndex
OBJECT-TYPE
The table entry number for this host.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.4.1.1GenericTableIndexnot-accessiblecurrent
authHostMacStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.4.1.2ContainerStatusread-writecurrent
authHostMacAddr
OBJECT-TYPE
The host MAC address used for this entry.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.4.1.3MacAddressread-writecurrent
authHostMacDescr
OBJECT-TYPE
The host MAC address entry description.
1.3.6.1.4.1.1966.21.1.1.1.2.2.5.4.1.4DisplayString (SIZE(0..21))read-writecurrent
mgtAlertGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.3
alertLocalEventGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.3.1
localEventLogStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.3.1.1ContainerStatusread-writecurrent
localEventLogEnabled
OBJECT-TYPE
Determines whether alert events are logged to the internal local event log.
1.3.6.1.4.1.1966.21.1.1.1.2.3.1.2YesNoValueread-writecurrent
localEventLogAlertLevel
OBJECT-TYPE
Choose the alert level that will trigger a local event being stored in the local event log. When you select an alert level, all alerts that appear above it in the list will also trigger a local event log message. For example, if you select oneTimeError, all oneTimeError, persistantError, moduleLevelFault, and systemLevelFault alert events will be generate a local event message.
1.3.6.1.4.1.1966.21.1.1.1.2.3.1.3AlertSeverityLevelread-writecurrent
localEventLogClear
OBJECT-TYPE
Writing a yes(1) to this object will clear the local event log on the management module. Reading of this object will always return 0
1.3.6.1.4.1.1966.21.1.1.1.2.3.1.4YesNoValueread-writecurrent
alertSyslogGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.3.2
syslogStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.3.2.1ContainerStatusread-writecurrent
syslogEnabled
OBJECT-TYPE
Determines whether syslog is enabled.
1.3.6.1.4.1.1966.21.1.1.1.2.3.2.2YesNoValueread-writecurrent
syslogSeverityLevel
OBJECT-TYPE
Choose the severity level that will trigger a syslog message: Emergency, Alert, Critical, Error, Warning, Notice, Info, Debug When you select a severity level, all the levels that appear above it in the list will also trigger a syslog message. For example, if you select Error, all Error, Critical, Alert, and Emergency events will generate a syslog message. NOTE: In addition to alert events, syslog message will also be generated for several non-alert system events
1.3.6.1.4.1.1966.21.1.1.1.2.3.2.3INTEGER {emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), informational(6), debug(7)}read-writecurrent
syslogPrimaryHost
OBJECT-TYPE
The first preconfigured host that the management module will attempt to send system log messages to; messages will be displayed on the host's monitor.
1.3.6.1.4.1.1966.21.1.1.1.2.3.2.4DisplayString (SIZE(0..14))read-writecurrent
syslogSecondaryHost
OBJECT-TYPE
If the management module cannot communicate with the primary host, then the management module will attempt to send system log messages to this preconfigured host; messages will be displayed on the host's monitor.
1.3.6.1.4.1.1966.21.1.1.1.2.3.2.5DisplayString (SIZE(0..14))read-writecurrent
alertSnmpTrapGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.3.3
snmpTrapStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.1ContainerStatusread-writecurrent
snmpTrapEnabled
OBJECT-TYPE
Determines whether SNMP Traps are enabled.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.2YesNoValueread-writecurrent
snmpTrapAlertLevel
OBJECT-TYPE
Choose the alert level that will trigger a SNMP trap message to be sent if SNMP traps is enabled. When you select an alert level, all alerts that appear above it in the list will also trigger a local event log message. For example, if you select oneTimeError, all oneTimeError, persistantError, moduleLevelFault, and systemLevelFault alert events will be generate a SNMP trap message.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.3AlertSeverityLevelread-writecurrent
snmpTrapHostTable
OBJECT-TYPE
Table of SNMP Trap Hosts information.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4not-accessiblecurrent
snmpTrapHostEntry
OBJECT-TYPE
Entries of the table, each relating to a separate SNMP trap host.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1not-accessiblecurrent
snmpTrapHostIndex
OBJECT-TYPE
This object identifies the SNMP trap host index.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1.1GenericTableIndexaccessible-for-notifycurrent
snmpTrapHostStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1.2ContainerStatusread-writecurrent
snmpTrapHostIpAddress
OBJECT-TYPE
Defines the hosts (by IP address) that will receive trap messages generated by the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1.3Ipv4v6Addressread-writecurrent
snmpTrapHostUdpPort
OBJECT-TYPE
Defines the UDP port number the SNMP trap host will listen on to receive trap messages generated by the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1.4Integer32 (1..65535)read-writecurrent
snmpTrapHostVersion
OBJECT-TYPE
Defines the SNMP version of the traps sent to this host. If snmpTrapV3 is selected then the SNMP trap v3 user
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1.5INTEGER {snmpTrapV1(0), snmpTrapV2c(1), snmpTrapV3(2)}read-writecurrent
snmpTrapHostType
OBJECT-TYPE
If set to snmpInform(1) the management module will send traps via an INFORM-PDU, expecting a response from the trap host, retransmitting if required. Otherwise it will send them via a TRAP-PDU or TRAP2-PDU. This object is ignored for for SNMP v1
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1.6INTEGER {snmpTrap(0), snmpInform(1)}read-writecurrent
snmpTrapHostCommunity
OBJECT-TYPE
An arbitrary trap community name. This object is ignored for SNMP v3
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1.7DisplayString (SIZE(0..14))read-writecurrent
snmpTrapHostEnable
OBJECT-TYPE
If set to No, the management module will not use this table entry to send traps.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.4.1.8YesNoValueread-writecurrent
snmpV3TrapUser
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.5
snmpV3TrapUserStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.5.1ContainerStatusread-writecurrent
snmpV3TrapUserUserName
OBJECT-TYPE
SNMP trap v3 user name. This user will be used for every SNMP trap host that is using snmpTrapHostVersion of snmpTrapV3(2)
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.5.2DisplayString (SIZE(0..16))read-writecurrent
snmpV3TrapUserSecurityLevel
OBJECT-TYPE
SNMP trap v3 user security level.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.5.3INTEGER {none(0), authNoPriv(1), authPriv(2)}read-writecurrent
snmpV3TrapUserAuthAlgorithm
OBJECT-TYPE
SNMP trap v3 user authentication method.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.5.4INTEGER {md5(0), sha(1)}read-writecurrent
snmpV3TrapUserAuthPasswd
OBJECT-TYPE
SNMP trap v3 user authentication password.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.5.5DisplayString (SIZE(0..128))read-writecurrent
snmpV3TrapUserPrivacyAlgorithm
OBJECT-TYPE
SNMP trap v3 user privacy algorithm.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.5.6INTEGER {des(0), aes(1)}read-writecurrent
snmpV3TrapUserPrivacyPasswd
OBJECT-TYPE
SNMP trap v3 user privacy password.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.5.7DisplayString (SIZE(0..128))read-writecurrent
snmpTrapGlbHostTimeout
OBJECT-TYPE
Defines the timeout in miliseconds between retries of sending the SNMP INFORM-PDU if no response is received for the trap host.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.6Integer32 (0..65535)read-writecurrent
snmpTapGlobHostRetries
OBJECT-TYPE
Defines the number of retries to send the SNMP INFORM-PDU trap if no response is received from the trap host.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.7Integer32 (0..65535)read-writecurrent
snmpV3LocalEngineID
OBJECT-TYPE
An SNMPv3 engine ID used by the MCR-MGT for identification when sending SNMP v3 traps.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.8SnmpEngineIDread-onlycurrent
snmpV3LocalEngineIDTextSuffix
OBJECT-TYPE
This configured text is used to build the suffix of the SNMPv3 engine ID
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.9DisplayString (SIZE(0..27))read-writecurrent
snmpTrapVarsGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10
mgtAccessMethod
OBJECT-TYPE
Defines the management protocol used to access the management module
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.1INTEGER {mgtConsole(1), mgtSnmp(2), mgtTelnet(3), mgtSSH(4), mgtHTTP(5), mgtHTTPS(6)}accessible-for-notifycurrent
remoteMgtIpAddress
OBJECT-TYPE
Defines the remote IP address accessing the management module
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.2DisplayStringaccessible-for-notifycurrent
remoteTftpHost
OBJECT-TYPE
Defines the remote TFTP server IP address or host name performing the TFP file transfer
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.3DisplayString (SIZE(0..64))accessible-for-notifycurrent
remoteTftpFileName
OBJECT-TYPE
Defines the remote TFTP file name
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.4DisplayString (SIZE(0..64))accessible-for-notifycurrent
networkIpAddress
OBJECT-TYPE
Defines the IP address assigned to the management module
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.5Ipv4v6Addressaccessible-for-notifycurrent
mcrMediaPortNum
OBJECT-TYPE
This object identifies the media converter module port number.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.6Unsigned32 (1..2)accessible-for-notifycurrent
mcrMediaPortDescr
OBJECT-TYPE
A description of the media port that consists of the user defined media port name, followed by the system name for the port.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.7DisplayStringaccessible-for-notifycurrent
eventSeverityLevel
OBJECT-TYPE
The severity level of the event that generated this trap.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.8AlertSeverityLevelaccessible-for-notifycurrent
xfpDmiRealTimeAux
OBJECT-TYPE
This object identifies the XFP DMI real time values for one of the auxillary register sets.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.9DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiHighAuxWarn
OBJECT-TYPE
This object identifies the XFP DMI high warning threshold for one of the auxillary register sets.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.10DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiHighAuxAlarm
OBJECT-TYPE
This object identifies the XFP DMI alarm alarm threshold for one of the auxillary register sets.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.11DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiLowAuxWarn
OBJECT-TYPE
This object identifies the XFP DMI low warning threshold for one of the auxillary register sets.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.12DisplayString (SIZE(0..32))read-onlycurrent
xfpDmiLowAuxAlarm
OBJECT-TYPE
This object identifies the XFP DMI low alarm threshold for one of the auxillary register sets.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.13DisplayString (SIZE(0..32))read-onlycurrent
mcrModuleSubTypeInserted
OBJECT-TYPE
This object identifies the module sub-type inserted in the slot.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.14INTEGER {blank(-1), sts(0), xts(1), xtsh(2), xtx(3), xtxh(4)}read-onlycurrent
mcrMediaBackedupModuleSubType
OBJECT-TYPE
This object identifies the module sub-type of the backup configuration.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.15INTEGER {blank(-1), sts(0), xts(1), xtsh(2), xtx(3), xtxh(4)}read-onlycurrent
mcrMediaPortBandwidth
OBJECT-TYPE
This object identifies the media converter module port's current bandwith in kbps.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.16Unsigned32accessible-for-notifycurrent
mcrMediaPortBandwidthThreshold
OBJECT-TYPE
This object identifies the media converter module port's bandwith threshold in kbps.
1.3.6.1.4.1.1966.21.1.1.1.2.3.3.10.17Unsigned32accessible-for-notifycurrent
alertEmailGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.3.4
emailStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.1ContainerStatusread-writecurrent
emailEnabled
OBJECT-TYPE
Determines whether or not email notification is turned on. Default is Off.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.2YesNoValueread-writecurrent
emailAlertLevel
OBJECT-TYPE
Choose the alert level that will trigger a email message to be sent if alert email is enabled. When you select an alert level, all alerts that appear above it in the list will also trigger a local event log message. For example, if you select oneTimeError, all oneTimeError, persistantError, moduleLevelFault, and systemLevelFault alert events will be generate a email message.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.3AlertSeverityLevelread-writecurrent
emailTo
OBJECT-TYPE
An email address or list of email addresses that will receive the email notification.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.4DisplayString (SIZE(0..64))read-writecurrent
emailFrom
OBJECT-TYPE
This field can contain an email address that might identify the management module name or some other value.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.5DisplayString (SIZE(0..32))read-writecurrent
emailSMTPHost
OBJECT-TYPE
The SMTP host (email server) that will process the email notification request. This can be either a host name defined in the management module host table or the SMTP host IP address.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.6DisplayString (SIZE(0..64))read-writecurrent
emailReply
OBJECT-TYPE
The email address to whom all replies to the email notification should go.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.7DisplayString (SIZE(0..32))read-writecurrent
emailSubject
OBJECT-TYPE
A text string, which can contain spaces, that will display in the Subject field of the email notification.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.8DisplayString (SIZE(0..48))read-writecurrent
emailSMTPUsername
OBJECT-TYPE
The user name for the SMTP server, if the server requires authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.9DisplayString (SIZE(0..64))read-writecurrent
emailSMTPPassword
OBJECT-TYPE
The password for the SMTP server, if the server requires authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.10DisplayString (SIZE(0..64))read-writecurrent
emailSMTPEncryption
OBJECT-TYPE
The encryption method for the SMTP server.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.11INTEGER {none(1), tls(2), ssl(3)}read-writecurrent
emailSMTPValidatePeerCertificate
OBJECT-TYPE
Validate peer SSL/TLS certificate, when SSL or TLS encryption is used.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.12OnOffValueread-writecurrent
emailSMTPTcpPort
OBJECT-TYPE
The TCP port used for communicating with the SMTP server. For no encryption or TLS encryption, use port 25. For SSL encryption, use port 465.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.13Integer32 (1..65535)read-writecurrent
emailSMTPDomain
OBJECT-TYPE
The domain for NTLM authentication with the SMTP server, if applicable.
1.3.6.1.4.1.1966.21.1.1.1.2.3.4.14DisplayString (SIZE(0..32))read-writecurrent
mgtUsersGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.4
mgtUsersStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.4.1ContainerStatusread-writecurrent
mgtUsersByPassLoginEnabled
OBJECT-TYPE
Indicates whether by pass login is enabled. When enable users will be automatically login as admin user. The will not be prompted for a user ID or password when accessing the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.4.2OnOffValueread-writecurrent
mgtUsersPrimaryAuthMethod
OBJECT-TYPE
The first authentication method that the management module attempts. Some type of authentication must be done by the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.4.3INTEGER {local(1), radius(2), kerberos(3), ldap(4), tacacs(5), securid(6), nis(7)}read-writecurrent
mgtUsersSecondaryAuthMethod
OBJECT-TYPE
If the Primary Authentication Method fails, the next authentication method that the management module attempts. You can choose to use authentication methods in combination. For example, you can specify the Primary Authentication Method as Local and the Secondary Authentication Method as RADIUS. Therefore, some users can be defined in the Device Server (Local) others in RADIUS.
1.3.6.1.4.1.1966.21.1.1.1.2.4.4INTEGER {none(1), local(2), radius(3), kerberos(4), ldap(5), tacacs(6), securid(7), nis(8)}read-writecurrent
mgtUsersAlwaysAttemptSecond
OBJECT-TYPE
If enabled, the secondary authentication method will always be used.
1.3.6.1.4.1.1966.21.1.1.1.2.4.5OnOffValueread-writecurrent
localUserAccountsTable
OBJECT-TYPE
Table of locally defined user information
1.3.6.1.4.1.1966.21.1.1.1.2.4.6not-accessiblecurrent
localUserAccountsEntry
OBJECT-TYPE
Entries of the table, each relating to separate user defined locally.
1.3.6.1.4.1.1966.21.1.1.1.2.4.6.1not-accessiblecurrent
userIndex
OBJECT-TYPE
The table entry number for this user.
1.3.6.1.4.1.1966.21.1.1.1.2.4.6.1.1GenericTableIndexnot-accessiblecurrent
userStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.4.6.1.2ContainerStatusread-writecurrent
userName
OBJECT-TYPE
The user name. To delete a user, set this field to blank. If blank, this entry is currently unused.
1.3.6.1.4.1.1966.21.1.1.1.2.4.6.1.3DisplayString (SIZE(0..16))read-writecurrent
userPassword
OBJECT-TYPE
The password for the local user.
1.3.6.1.4.1.1966.21.1.1.1.2.4.6.1.4DisplayString (SIZE(0..64))read-writecurrent
userLevel
OBJECT-TYPE
Admin: Total access to the management module. More than one admin user account can exist, but we recommend that you only have one. operator: Full read only access to configuration and limited control commands
1.3.6.1.4.1.1966.21.1.1.1.2.4.6.1.5INTEGER {admin(0), operator(1)}read-writecurrent
localUsersStatusTable
OBJECT-TYPE
Table of locally defined user information
1.3.6.1.4.1.1966.21.1.1.1.2.4.7not-accessiblecurrent
localUsersStatusEntry
OBJECT-TYPE
Entries of the table, each relating to separate user defined locally.
1.3.6.1.4.1.1966.21.1.1.1.2.4.7.1not-accessiblecurrent
userStatusIndex
OBJECT-TYPE
The table entry number for this user status.
1.3.6.1.4.1.1966.21.1.1.1.2.4.7.1.1GenericTableIndexnot-accessiblecurrent
userStatusName
OBJECT-TYPE
The user name. To delete a user, set this field to blank. If blank, this entry is currently unused.
1.3.6.1.4.1.1966.21.1.1.1.2.4.7.1.2DisplayString (SIZE(0..16))read-onlycurrent
userStatusMgtAccessType
OBJECT-TYPE
Defines the management protocol used to access the management module
1.3.6.1.4.1.1966.21.1.1.1.2.4.7.1.3INTEGER {mgtAccessHTTP(1), mgtAccessHTTPS(2), mgtAccessTelnet(3), mgtAccessSSH(4), mgtAccessConsole(5)}not-accessiblecurrent
userStatusRemoteIPAddress
OBJECT-TYPE
This object specifies the remote IP address user management session.
1.3.6.1.4.1.1966.21.1.1.1.2.4.7.1.4Ipv4v6Addressread-onlycurrent
userStatusStartTime
OBJECT-TYPE
This object identifies the date and time that the current user's management session started.
1.3.6.1.4.1.1966.21.1.1.1.2.4.7.1.5DisplayStringread-onlycurrent
userStatusLevel
OBJECT-TYPE
Admin: Total access to the management module. More than one admin user account can exist, but we recommend that you only have one. operator: Full read only access to configuration and limited control commands
1.3.6.1.4.1.1966.21.1.1.1.2.4.7.1.6INTEGER {admin(0), operator(1)}read-onlycurrent
radiusGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.4.8
radiusStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.1ContainerStatusread-writecurrent
radiusPrimaryAuthHost
OBJECT-TYPE
Primary Radius Authentication Host
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.2DisplayString (SIZE(0..14))read-writecurrent
radiusSecondaryAuthHost
OBJECT-TYPE
Secondary Radius Authentication Host
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.3DisplayString (SIZE(0..14))read-writecurrent
radiusAuthenticationPort
OBJECT-TYPE
The port that the RADIUS host listens to for authentication requests. The default port is 1812.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.4Integer32 (0..65535)read-writecurrent
radiusAccounting
OBJECT-TYPE
Radius Accounting
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.5OnOffValueread-writecurrent
radiusPrimaryAcctHost
OBJECT-TYPE
Name of the primary RADIUS authentication host.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.6DisplayString (SIZE(0..14))read-writecurrent
radiusSecondaryAcctHost
OBJECT-TYPE
Name of the secondary RADIUS authentication host.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.7DisplayString (SIZE(0..14))read-writecurrent
radiusAccountingPort
OBJECT-TYPE
The port that the RADIUS host listens to for accounting requests. The default port is 1813.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.8Integer32 (0..65535)read-writecurrent
radiusAcctAuth
OBJECT-TYPE
Radius Accounting Authenticator
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.9OnOffValueread-writecurrent
radiusRetryLimit
OBJECT-TYPE
The number of times the management module tries to connect to the RADIUS server before erroring out. Valid values are 0-255. The default is 5.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.10Integer32 (0..255)read-writecurrent
radiusTimeout
OBJECT-TYPE
The time, in seconds, that the management module waits to receive a reply after sending out a request to a RADIUS accounting or authentication host. If no reply is received before the timeout period expires, the management module will retry the same host up to and including the number of retry attempts. Valid values are 1-255. The default is 3 seconds.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.11Integer32 (1..255)read-writecurrent
radiusNasIdentifier
OBJECT-TYPE
The NAS identifier name. To delete this , set this field to blank.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.12DisplayString (SIZE(0..32))read-writecurrent
radiusNasIpAddress
OBJECT-TYPE
When on, the NAS Identifier obtains ipv4 address automatically. Default is on.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.13OnOffValueread-writecurrent
radiusNasSpecifyIpAddress
OBJECT-TYPE
Specify the unique IPv4 address that NAS Identifier will use
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.14IpAddressread-writecurrent
radiusNasIpv6Address
OBJECT-TYPE
When on, the NAS Identifier obtains ipv6 address automatically. Default is on.
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.15OnOffValueread-writecurrent
radiusNasSpecifyIpv6Address
OBJECT-TYPE
Specify the unique IPv6 address that NAS Identifier will use
1.3.6.1.4.1.1966.21.1.1.1.2.4.8.16DisplayStringread-writecurrent
kerberosGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.4.9
kerberosStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.4.9.1ContainerStatusread-writecurrent
kerberosRealm
OBJECT-TYPE
The Kerberos realm is the Kerberos host domain name, in upper-case letters.
1.3.6.1.4.1.1966.21.1.1.1.2.4.9.2DisplayString (SIZE(0..32))read-writecurrent
kerberosDomain
OBJECT-TYPE
The name of a host running the KDC (Key Distribution Center) for the specified realm. The host name that you specify must either be defined in the management module's host Table before the last reboot or be resolved by DNS.
1.3.6.1.4.1.1966.21.1.1.1.2.4.9.3DisplayString (SIZE(0..32))read-writecurrent
kerberosPort
OBJECT-TYPE
The port that the Kerberos server listens to for authentication requests. If no port is specified, the default port 88 is used.
1.3.6.1.4.1.1966.21.1.1.1.2.4.9.4Integer32 (0..65535)read-writecurrent
ldapGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.4.10
ldapStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.1ContainerStatusread-writecurrent
ldapHost
OBJECT-TYPE
The name or IP address of the LDAP host. If you use a host name, that host must either have been defined in the management module's Host Table before the last reboot or be resolved by DNS. If you are using TLS, you must enter the same string you used to create the LDAP certificate.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.2DisplayString (SIZE(0..64))read-writecurrent
ldapPort
OBJECT-TYPE
The port that the LDAP host listens to for authentication requests. The default port is 389.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.3Integer32 (0..65535)read-writecurrent
ldapBase
OBJECT-TYPE
The domain component (dc) that is the starting point for the search for user authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.4DisplayString (SIZE(0..64))read-writecurrent
ldapEnableTLS
OBJECT-TYPE
Enables/disables the Transport Layer Security (TLS) with the LDAP host.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.5OnOffValueread-writecurrent
ldapTLSPort
OBJECT-TYPE
Specify the port number that LDAP will use for TLS. The default is port 636.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.6Integer32 (0..65535)read-writecurrent
ldapUID
OBJECT-TYPE
LDAP user attribute. e.g. uid (OpenLDAP) sAMAccountName (Active Directory) The default is 'uid'.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.7DisplayString (SIZE(0..32))read-writecurrent
ldapPasswordEncryption
OBJECT-TYPE
LDAP password encryption method.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.8INTEGER {none(1), md5(2)}read-writecurrent
ldapClientAuth
OBJECT-TYPE
LDAP client authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.9OnOffValueread-writecurrent
ldapClientName
OBJECT-TYPE
LDAP client name. Identifies the unit to the LDAP server, when client authentication is .
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.10DisplayString (SIZE(0..64))read-writecurrent
ldapClientAppendBase
OBJECT-TYPE
Append base to LDAP client name.
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.11OnOffValueread-writecurrent
ldapClientPassword
OBJECT-TYPE
LDAP client password. Identifies the unit to the LDAP server, when client authentication is .
1.3.6.1.4.1.1966.21.1.1.1.2.4.10.12DisplayString (SIZE(0..64))read-writecurrent
tacacsGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.4.11
tacacsStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.1ContainerStatusread-writecurrent
tacacsPrimaryHost
OBJECT-TYPE
The primary TACACS+ host that is used for authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.2DisplayString (SIZE(0..14))read-writecurrent
tacacsSecondaryHost
OBJECT-TYPE
The secondary TACACS+ host that is used for authentication, should the primary TACACS+ host fail to respond.
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.3DisplayString (SIZE(0..14))read-writecurrent
tacacsPort
OBJECT-TYPE
The port number that TACACS+ listens to for authentication requests. The default port number is 49.
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.4Integer32 (0..65535)read-writecurrent
tacacsAccounting
OBJECT-TYPE
Enable/Disable TACACS+ accounting
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.5OnOffValueread-writecurrent
tacacsAccountingPrimaryHost
OBJECT-TYPE
The primary TACACS+ accounting host that is used for.
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.6DisplayString (SIZE(0..14))read-writecurrent
tacacsAccountingSecondaryHost
OBJECT-TYPE
The secondary TACACS+ accounting host that is used for , should the primary TACACS+ host fail to respond.
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.7DisplayString (SIZE(0..14))read-writecurrent
tacacsAccountingPort
OBJECT-TYPE
The port number that TACACS+ listens to for accounting requests. The default port number is 49.
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.8Integer32 (0..65535)read-writecurrent
tacacsAuthorization
OBJECT-TYPE
Enable/Disable TACACS+ authorization
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.9OnOffValueread-writecurrent
tacacsAlternateServiceNames
OBJECT-TYPE
Enable alternate service names for TACACS+.
1.3.6.1.4.1.1966.21.1.1.1.2.4.11.10OnOffValueread-writecurrent
securidGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.4.12
securidStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.4.12.1ContainerStatusread-writecurrent
securidMasterHost
OBJECT-TYPE
The first SecurID server that is tried for user authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.4.12.2DisplayString (SIZE(0..14))read-writecurrent
securidSlaveHost
OBJECT-TYPE
If the first SecurID server does not respond to an authentication request, this is the next SecurID server that is tried for user authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.4.12.3DisplayString (SIZE(0..14))read-writecurrent
securidPort
OBJECT-TYPE
The port number that SecurID listens to for authentication requests. The default port number is 5500.
1.3.6.1.4.1.1966.21.1.1.1.2.4.12.4Integer32 (0..65535)read-writecurrent
securidType
OBJECT-TYPE
You can specify either SDI or DES encryption for SecurID server communication. The default is SDI encryption.
1.3.6.1.4.1.1966.21.1.1.1.2.4.12.5INTEGER {des(1), sdi(2)}read-writecurrent
securidLegacy
OBJECT-TYPE
If you are running SecurID 3.x or 4.x, you need to run in Legacy Mode. If you are running SecurID 5.x or above, do not select Legacy Mode.
1.3.6.1.4.1.1966.21.1.1.1.2.4.12.6YesNoValueread-writecurrent
nisGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.4.13
nisStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.4.13.1ContainerStatusread-writecurrent
nisDomain
OBJECT-TYPE
The NIS domain name.
1.3.6.1.4.1.1966.21.1.1.1.2.4.13.2DisplayString (SIZE(0..32))read-writecurrent
nisPrimaryHost
OBJECT-TYPE
The primary NIS host that is used for authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.4.13.3DisplayString (SIZE(0..14))read-writecurrent
nisSecondaryHost
OBJECT-TYPE
The secondary NIS host that is used for authentication, should the primary NIS host fail to respond.
1.3.6.1.4.1.1966.21.1.1.1.2.4.13.4DisplayString (SIZE(0..14))read-writecurrent
mgtDateTimeGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.5
mgtDateTimeStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.5.1ContainerStatusread-writecurrent
systemDate
OBJECT-TYPE
The system date. Format dd/mm/yyyy.
1.3.6.1.4.1.1966.21.1.1.1.2.5.2DisplayStringread-writecurrent
systemTime
OBJECT-TYPE
The system time (local time). Format hh:mm:ss.
1.3.6.1.4.1.1966.21.1.1.1.2.5.3DisplayStringread-writecurrent
systemDateTimeAndOffset
OBJECT-TYPE
This read only object identifies the current system date, time and GMT offset. The date and time will be displayed in the regional time format configured.
1.3.6.1.4.1.1966.21.1.1.1.2.5.4DisplayStringread-onlycurrent
timeZoneListEnable
OBJECT-TYPE
When the time zone list is enabled then the time zone being use is the one selected form the predefined list of time zones. If not enabled then the customTimeZoneGroup will define the time zone being used
1.3.6.1.4.1.1966.21.1.1.1.2.5.5OnOffValueread-writecurrent
selectionFromTimeZoneList
OBJECT-TYPE
This object identifies the predefined time zone selected. This time zone will be used if timeZoneListEnable object is set to yes. configured.
1.3.6.1.4.1.1966.21.1.1.1.2.5.6INTEGER {tzAfricaAbidjan(0), tzAfricaAccra(1), tzAfricaAddisAbaba(2), tzAfricaAlgiers(3), tzAfricaAsmera(4), tzAfricaBamako(5), tzAfricaBangui(6), tzAfricaBanjul(7), tzAfricaBissau(8), tzAfricaBlantyre(9), tzAfricaBrazzaville(10), tzAfricaBujumbura(11), tzAfricaCairo(12), tzAfricaCasablanca(13), tzAfricaCeuta(14), tzAfricaConakry(15), tzAfricaDakar(16), tzAfricaDaresSalaam(17), tzAfricaDjibouti(18), tzAfricaDouala(19), tzAfricaElAaiun(20), tzAfricaFreetown(21), tzAfricaGaborone(22), tzAfricaHarare(23), tzAfricaJohannesburg(24), tzAfricaKampala(25), tzAfricaKhartoum(26), tzAfricaKigali(27), tzAfricaKinshasa(28), tzAfricaLagos(29), tzAfricaLibreville(30), tzAfricaLome(31), tzAfricaLuanda(32), tzAfricaLubumbashi(33), tzAfricaLusaka(34), tzAfricaMalabo(35), tzAfricaMaputo(36), tzAfricaMaseru(37), tzAfricaMbabane(38), tzAfricaMogadishu(39), tzAfricaMonrovia(40), tzAfricaNairobi(41), tzAfricaNdjamena(42), tzAfricaNiamey(43), tzAfricaNouakchott(44), tzAfricaOuagadougou(45), tzAfricaPortoNovo(46), tzAfricaSaoTome(47), tzAfricaTimbuktu(48), tzAfricaTripoli(49), tzAfricaTunis(50), tzAfricaWindhoek(51), tzAmericaAdak(52), tzAmericaAnchorage(53), tzAmericaAnguilla(54), tzAmericaAntigua(55), tzAmericaAraguaina(56), tzAmericaAruba(57), tzAmericaAsuncion(58), tzAmericaAtka(59), tzAmericaBarbados(60), tzAmericaBelem(61), tzAmericaBelize(62), tzAmericaBoaVista(63), tzAmericaBogota(64), tzAmericaBoise(65), tzAmericaBuenosAires(66), tzAmericaCambridgeBay(67), tzAmericaCancun(68), tzAmericaCaracas(69), tzAmericaCatamarca(70), tzAmericaCayenne(71), tzAmericaCayman(72), tzAmericaChicago(73), tzAmericaChihuahua(74), tzAmericaCordoba(75), tzAmericaCostaRica(76), tzAmericaCuiaba(77), tzAmericaCuracao(78), tzAmericaDanmarkshavn(79), tzAmericaDawson(80), tzAmericaDawsonCreek(81), tzAmericaDenver(82), tzAmericaDetroit(83), tzAmericaDominica(84), tzAmericaEdmonton(85), tzAmericaEirunepe(86), tzAmericaElSalvador(87), tzAmericaEnsenada(88), tzAmericaFortWayne(89), tzAmericaFortaleza(90), tzAmericaGlaceBay(91), tzAmericaGodthab(92), tzAmericaGooseBay(93), tzAmericaGrandTurk(94), tzAmericaGrenada(95), tzAmericaGuadeloupe(96), tzAmericaGuatemala(97), tzAmericaGuayaquil(98), tzAmericaGuyana(99), tzAmericaHalifax(100), tzAmericaHavana(101), tzAmericaHermosillo(102), tzAmericaIndianaIndianapolis(103), tzAmericaIndianaKnox(104), tzAmericaIndianaMarengo(105), tzAmericaIndianaVevay(106), tzAmericaIndianapolis(107), tzAmericaInuvik(108), tzAmericaIqaluit(109), tzAmericaJamaica(110), tzAmericaJujuy(111), tzAmericaJuneau(112), tzAmericaKentuckyLouisville(113), tzAmericaKentuckyMonticello(114), tzAmericaKnoxIN(115), tzAmericaLaPaz(116), tzAmericaLima(117), tzAmericaLosAngeles(118), tzAmericaLouisville(119), tzAmericaMaceio(120), tzAmericaManagua(121), tzAmericaManaus(122), tzAmericaMartinique(123), tzAmericaMazatlan(124), tzAmericaMendoza(125), tzAmericaMenominee(126), tzAmericaMerida(127), tzAmericaMexicoCity(128), tzAmericaMiquelon(129), tzAmericaMonterrey(130), tzAmericaMontevideo(131), tzAmericaMontreal(132), tzAmericaMontserrat(133), tzAmericaNassau(134), tzAmericaNewYork(135), tzAmericaNipigon(136), tzAmericaNome(137), tzAmericaNoronha(138), tzAmericaNorthDakotaCenter(139), tzAmericaPanama(140), tzAmericaPangnirtung(141), tzAmericaParamaribo(142), tzAmericaPhoenix(143), tzAmericaPortofSpain(144), tzAmericaPortauPrince(145), tzAmericaPortoAcre(146), tzAmericaPortoVelho(147), tzAmericaPuertoRico(148), tzAmericaRainyRiver(149), tzAmericaRankinInlet(150), tzAmericaRecife(151), tzAmericaRegina(152), tzAmericaRioBranco(153), tzAmericaRosario(154), tzAmericaSantiago(155), tzAmericaSantoDomingo(156), tzAmericaSaoPaulo(157), tzAmericaScoresbysund(158), tzAmericaShiprock(159), tzAmericaStJohns(160), tzAmericaStKitts(161), tzAmericaStLucia(162), tzAmericaStThomas(163), tzAmericaStVincent(164), tzAmericaSwiftCurrent(165), tzAmericaTegucigalpa(166), tzAmericaThule(167), tzAmericaThunderBay(168), tzAmericaTijuana(169), tzAmericaTortola(170), tzAmericaVancouver(171), tzAmericaVirgin(172), tzAmericaWhitehorse(173), tzAmericaWinnipeg(174), tzAmericaYakutat(175), tzAmericaYellowknife(176), tzAntarcticaCasey(177), tzAntarcticaDavis(178), tzAntarcticaDumontDUrville(179), tzAntarcticaMawson(180), tzAntarcticaMcMurdo(181), tzAntarcticaPalmer(182), tzAntarcticaSouthPole(183), tzAntarcticaSyowa(184), tzAntarcticaVostok(185), tzArcticLongyearbyen(186), tzAsiaAden(187), tzAsiaAlmaty(188), tzAsiaAmman(189), tzAsiaAnadyr(190), tzAsiaAqtau(191), tzAsiaAqtobe(192), tzAsiaAshgabat(193), tzAsiaAshkhabad(194), tzAsiaBaghdad(195), tzAsiaBahrain(196), tzAsiaBaku(197), tzAsiaBangkok(198), tzAsiaBeirut(199), tzAsiaBishkek(200), tzAsiaBrunei(201), tzAsiaCalcutta(202), tzAsiaChoibalsan(203), tzAsiaChongqing(204), tzAsiaChungking(205), tzAsiaColombo(206), tzAsiaDacca(207), tzAsiaDamascus(208), tzAsiaDhaka(209), tzAsiaDili(210), tzAsiaDubai(211), tzAsiaDushanbe(212), tzAsiaGaza(213), tzAsiaHarbin(214), tzAsiaHongKong(215), tzAsiaHovd(216), tzAsiaIrkutsk(217), tzAsiaIstanbul(218), tzAsiaJakarta(219), tzAsiaJayapura(220), tzAsiaJerusalem(221), tzAsiaKabul(222), tzAsiaKamchatka(223), tzAsiaKarachi(224), tzAsiaKashgar(225), tzAsiaKatmandu(226), tzAsiaKrasnoyarsk(227), tzAsiaKualaLumpur(228), tzAsiaKuching(229), tzAsiaKuwait(230), tzAsiaMacao(231), tzAsiaMagadan(232), tzAsiaManila(233), tzAsiaMuscat(234), tzAsiaNicosia(235), tzAsiaNovosibirsk(236), tzAsiaOmsk(237), tzAsiaPhnomPenh(238), tzAsiaPontianak(239), tzAsiaPyongyang(240), tzAsiaQatar(241), tzAsiaRangoon(242), tzAsiaRiyadh(243), tzAsiaSaigon(244), tzAsiaSakhalin(245), tzAsiaSamarkand(246), tzAsiaSeoul(247), tzAsiaShanghai(248), tzAsiaSingapore(249), tzAsiaTaipei(250), tzAsiaTashkent(251), tzAsiaTbilisi(252), tzAsiaTehran(253), tzAsiaTelAviv(254), tzAsiaThimbu(255), tzAsiaThimphu(256), tzAsiaTokyo(257), tzAsiaUjungPandang(258), tzAsiaUlaanbaatar(259), tzAsiaUlanBator(260), tzAsiaUrumqi(261), tzAsiaVientiane(262), tzAsiaVladivostok(263), tzAsiaYakutsk(264), tzAsiaYekaterinburg(265), tzAsiaYerevan(266), tzAtlanticAzores(267), tzAtlanticBermuda(268), tzAtlanticCanary(269), tzAtlanticCapeVerde(270), tzAtlanticFaeroe(271), tzAtlanticJanMayen(272), tzAtlanticMadeira(273), tzAtlanticReykjavik(274), tzAtlanticSouthGeorgia(275), tzAtlanticStHelena(276), tzAtlanticStanley(277), tzAustraliaACT(278), tzAustraliaAdelaide(279), tzAustraliaBrisbane(280), tzAustraliaBrokenHill(281), tzAustraliaCanberra(282), tzAustraliaDarwin(283), tzAustraliaHobart(284), tzAustraliaLHI(285), tzAustraliaLindeman(286), tzAustraliaLordHowe(287), tzAustraliaMelbourne(288), tzAustraliaNSW(289), tzAustraliaNorth(290), tzAustraliaPerth(291), tzAustraliaQueensland(292), tzAustraliaSouth(293), tzAustraliaSydney(294), tzAustraliaTasmania(295), tzAustraliaVictoria(296), tzAustraliaWest(297), tzAustraliaYancowinna(298), tzBrazilDeNoronha(299), tzBrazilEast(300), tzBrazilWest(301), tzCanadaAtlantic(302), tzCanadaCentral(303), tzCanadaEastSaskatchewan(304), tzCanadaEastern(305), tzCanadaMountain(306), tzCanadaNewfoundland(307), tzCanadaPacific(308), tzCanadaSaskatchewan(309), tzCanadaYukon(310), tzChileContinental(311), tzChileEasterIsland(312), tzCuba(313), tzEgypt(314), tzEire(315), tzEuropeAmsterdam(316), tzEuropeAndorra(317), tzEuropeAthens(318), tzEuropeBelfast(319), tzEuropeBelgrade(320), tzEuropeBerlin(321), tzEuropeBratislava(322), tzEuropeBrussels(323), tzEuropeBucharest(324), tzEuropeBudapest(325), tzEuropeChisinau(326), tzEuropeCopenhagen(327), tzEuropeDublin(328), tzEuropeGibraltar(329), tzEuropeHelsinki(330), tzEuropeIstanbul(331), tzEuropeKaliningrad(332), tzEuropeKiev(333), tzEuropeLisbon(334), tzEuropeLjubljana(335), tzEuropeLondon(336), tzEuropeLuxembourg(337), tzEuropeMadrid(338), tzEuropeMalta(339), tzEuropeMinsk(340), tzEuropeMonaco(341), tzEuropeMoscow(342), tzEuropeNicosia(343), tzEuropeOslo(344), tzEuropeParis(345), tzEuropePrague(346), tzEuropeRiga(347), tzEuropeRome(348), tzEuropeSamara(349), tzEuropeSanMarino(350), tzEuropeSarajevo(351), tzEuropeSimferopol(352), tzEuropeSkopje(353), tzEuropeSofia(354), tzEuropeStockholm(355), tzEuropeTallinn(356), tzEuropeTirane(357), tzEuropeTiraspol(358), tzEuropeUzhgorod(359), tzEuropeVaduz(360), tzEuropeVatican(361), tzEuropeVienna(362), tzEuropeVilnius(363), tzEuropeWarsaw(364), tzEuropeZagreb(365), tzEuropeZaporozhye(366), tzEuropeZurich(367), tzGreatBritainEire(368), tzGreatBritainGreatBritain(369), tzHongKong(370), tzIceland(371), tzIndianAntananarivo(372), tzIndianChagos(373), tzIndianChristmas(374), tzIndianCocos(375), tzIndianComoro(376), tzIndianKerguelen(377), tzIndianMahe(378), tzIndianMaldives(379), tzIndianMauritius(380), tzIndianMayotte(381), tzIndianReunion(382), tzIran(383), tzIsrael(384), tzJamaica(385), tzJapan(386), tzKwajalein(387), tzLibya(388), tzMexicoBajaNorte(389), tzMexicoBajaSur(390), tzMexicoGeneral(391), tzNavajo(392), tzNewZealandChatham(393), tzNewZealandNewZealand(394), tzPacificApia(395), tzPacificAuckland(396), tzPacificChatham(397), tzPacificEaster(398), tzPacificEfate(399), tzPacificEnderbury(400), tzPacificFakaofo(401), tzPacificFiji(402), tzPacificFunafuti(403), tzPacificGalapagos(404), tzPacificGambier(405), tzPacificGuadalcanal(406), tzPacificGuam(407), tzPacificHonolulu(408), tzPacificJohnston(409), tzPacificKiritimati(410), tzPacificKosrae(411), tzPacificKwajalein(412), tzPacificMajuro(413), tzPacificMarquesas(414), tzPacificMidway(415), tzPacificNauru(416), tzPacificNiue(417), tzPacificNorfolk(418), tzPacificNoumea(419), tzPacificPagoPago(420), tzPacificPalau(421), tzPacificPitcairn(422), tzPacificPonape(423), tzPacificPortMoresby(424), tzPacificRarotonga(425), tzPacificSaipan(426), tzPacificSamoa(427), tzPacificTahiti(428), tzPacificTarawa(429), tzPacificTongatapu(430), tzPacificTruk(431), tzPacificWake(432), tzPacificWallis(433), tzPacificYap(434), tzPoland(435), tzPortugal(436), tzSingapore(437), tzTurkey(438), tzUSAlaska(439), tzUSAleutian(440), tzUSArizona(441), tzUSCentral(442), tzUSEastIndiana(443), tzUSEastern(444), tzUSHawaii(445), tzUSIndianaStarke(446), tzUSMichigan(447), tzUSMountain(448), tzUSPacific(449), tzUSSamoa(450)}read-writecurrent
timeZoneAdjustForDST
OBJECT-TYPE
This object identifies if the time will be adjusted for DST (Daylight Savings Time) or not.
1.3.6.1.4.1.1966.21.1.1.1.2.5.7YesNoValueread-writecurrent
customTimeZoneGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.5.8
customTimeZoneStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.1ContainerStatusread-writecurrent
timeZoneName
OBJECT-TYPE
The name of the time zone when using standard time.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.2DisplayString (SIZE(0..4))read-writecurrent
timeOffset
OBJECT-TYPE
The offset of summer time from standard time in minutes.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.3Integer32 (-720..840)read-writecurrent
timeSummerName
OBJECT-TYPE
The name of the time zone when using summer time.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.4DisplayString (SIZE(0..4))read-writecurrent
timeSummerOffset
OBJECT-TYPE
The offset of summer time from standard time in minutes.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.5Integer32 (0..180)read-writecurrent
timeSummerMode
OBJECT-TYPE
You can configure the summer time to take effect: None-No summer time change. Fixed-The summer time change goes into effect at the specified time every year. For example, April 15 at 1:00 pm. Recurring-The summer time changes goes into effect every year at same relative time. For example, on the third week in April on a Tuesday at 1:00 pm.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.6INTEGER {disabled(0), fixed(1), recurring(2)}read-writecurrent
timeSummerRecStartMonth
OBJECT-TYPE
The recurring summer time start month.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.7INTEGER {january(0), february(1), march(2), april(3), may(4), june(5), july(6), august(7), september(8), october(9), november(10), december(11)}read-writecurrent
timeSummerRecStartWeek
OBJECT-TYPE
The recurring summer time start week.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.8INTEGER {first(0), second(1), third(2), fourth(3), last(4)}read-writecurrent
timeSummerRecStartDay
OBJECT-TYPE
The recurring summer time start day.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.9INTEGER {sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6)}read-writecurrent
timeSummerRecStartHour
OBJECT-TYPE
The recurring summer time start hour.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.10Integer32 (0..23)read-writecurrent
timeSummerRecStartMin
OBJECT-TYPE
The recurring summer time start minute
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.11Integer32 (0..59)read-writecurrent
timeSummerRecEndMonth
OBJECT-TYPE
The recurring summer time end month.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.12INTEGER {january(0), february(1), march(2), april(3), may(4), june(5), july(6), august(7), september(8), october(9), november(10), december(11)}read-writecurrent
timeSummerRecEndWeek
OBJECT-TYPE
The recurring summer time end week.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.13INTEGER {first(0), second(1), third(2), fourth(3), last(4)}read-writecurrent
timeSummerRecEndDay
OBJECT-TYPE
The recurring summer time end day.
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.14INTEGER {sunday(0), monday(1), tuesday(2), wednesday(3), thursday(4), friday(5), saturday(6)}read-writecurrent
timeSummerRecEndHour
OBJECT-TYPE
The recurring summer time end hour
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.15Integer32 (0..23)read-writecurrent
timeSummerRecEndMin
OBJECT-TYPE
The recurring summer time end minute
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.16Integer32 (0..59)read-writecurrent
timeSummerFixStartMonth
OBJECT-TYPE
The fixed summer time start month
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.17INTEGER {january(0), february(1), march(2), april(3), may(4), june(5), july(6), august(7), september(8), october(9), november(10), december(11)}read-writecurrent
timeSummerFixStartDay
OBJECT-TYPE
The fixed summer time start day
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.18Integer32 (1..31)read-writecurrent
timeSummerFixStartHour
OBJECT-TYPE
The fixed summer time start hour
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.19Integer32 (0..23)read-writecurrent
timeSummerFixStartMinute
OBJECT-TYPE
The fixed summer time start minute
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.20Integer32 (0..59)read-writecurrent
timeSummerFixEndMonth
OBJECT-TYPE
The fixed summer time End month
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.21INTEGER {january(0), february(1), march(2), april(3), may(4), june(5), july(6), august(7), september(8), october(9), november(10), december(11)}read-writecurrent
timeSummerFixEndDay
OBJECT-TYPE
The fixed summer time End day
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.22Integer32 (1..31)read-writecurrent
timeSummerFixEndHour
OBJECT-TYPE
The fixed summer time End hour
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.23Integer32 (0..23)read-writecurrent
timeSummerFixEndMinute
OBJECT-TYPE
The fixed summer time End minute
1.3.6.1.4.1.1966.21.1.1.1.2.5.8.24Integer32 (0..59)read-writecurrent
networkTimeGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.5.9
timeStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.1ContainerStatusread-writecurrent
timeSntpMode
OBJECT-TYPE
The SNTP client mode. Valid modes are Disabled, Unicast, Multicast or Anycast
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.2INTEGER {disabled(0), unicast(1), multicast(2), anycast(3)}read-writecurrent
timeSntpVersion
OBJECT-TYPE
The sntp client version.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.3INTEGER {version1(0), version2(1), version3(2), version4(3)}read-writecurrent
timeSntpHost1
OBJECT-TYPE
The first remote SNTP host name that the device server communicates with.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.4DisplayString (SIZE(0..14))read-writecurrent
timeSntpHost2
OBJECT-TYPE
The second remote SNTP host name that the device server communicates with.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.5DisplayString (SIZE(0..14))read-writecurrent
sntpStatGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6
sntpStatAddress
OBJECT-TYPE
The address of the remote SNMP host that updated the time.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6.1DisplayStringread-onlycurrent
sntpStatLastUpdate
OBJECT-TYPE
The time of the last update.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6.2DisplayStringread-onlycurrent
sntpStatLeapIndicator
OBJECT-TYPE
The leap year indicator.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6.3INTEGER {noWarning(0), minutes61(1), minutes59(2), alarm(3)}read-onlycurrent
sntpStatVersion
OBJECT-TYPE
The SNTP version.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6.4INTEGER {ipV4(3), ipv4ipv6osi(4)}read-onlycurrent
sntpStatMode
OBJECT-TYPE
The current SNTP mode
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6.5INTEGER {reserved(0), symmetricActive(1), symmetricPassive(2), client(3), server(4), broadcast(5), reservedNTP(6), reserved2(7)}read-onlycurrent
sntpStatStratum
OBJECT-TYPE
The SNTP stratum.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6.6Integer32 (0..15)read-onlycurrent
sntpStatRefId
OBJECT-TYPE
The SNTP reference ID.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6.7Unsigned32read-onlycurrent
sntpStatOffset
OBJECT-TYPE
The SNTP offset
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.6.8Unsigned32read-onlycurrent
timeSntpServerAuthentication
OBJECT-TYPE
Specifies whether to authenticate with the ntp time server.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.7INTEGER {off(1), on(2)}read-writecurrent
timeSntpKeyID
OBJECT-TYPE
Specifies the key ID to use for host 1 during server authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.8INTEGERread-writecurrent
timeSntpKeyID2
OBJECT-TYPE
Specifies the key ID to use for host 2 during server authentication.
1.3.6.1.4.1.1966.21.1.1.1.2.5.9.9INTEGERread-writecurrent
mgtFilesGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.6
mgtBootFilesGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.6.1
bootFileStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.6.1.1ContainerStatusread-writecurrent
fileFirmwareHost
OBJECT-TYPE
The host name or IP address of the server that contains the firmware file. If you use a host name, it must exist in the management module's host table or be resolved by DNS.
1.3.6.1.4.1.1966.21.1.1.1.2.6.1.2DisplayString (SIZE(0..46))read-writecurrent
fileFirmwareName
OBJECT-TYPE
The path and file name (do not use a drive letter), relative to the default path of your TFTP server software, of the update software for the management module that will be loaded when the management module is rebooted.
1.3.6.1.4.1.1966.21.1.1.1.2.6.1.3DisplayString (SIZE(0..64))read-writecurrent
fileConfigurationHost
OBJECT-TYPE
The host name or IP address of the server that contains the configuration file. If you use a host name, it must exist in the management module's host table or be resolved by DNS.
1.3.6.1.4.1.1966.21.1.1.1.2.6.1.4DisplayString (SIZE(0..46))read-writecurrent
fileConfigurationName
OBJECT-TYPE
The path and file name (do not use a drive letter), relative to the default path of your TFTP server software, of the new configuration file for the Device Server that will be loaded when the management module is rebooted.
1.3.6.1.4.1.1966.21.1.1.1.2.6.1.5DisplayString (SIZE(0..64))read-writecurrent
mgtfirmwareUpdatesGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.6.2
firmwareUpdateStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.1ContainerStatusread-writecurrent
firmwareUpdateAuto
OBJECT-TYPE
Enable automatic updates of installed media converter modules from firmware bundle on management module..
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.2OnOffValueread-writecurrent
firmwareUpdateBundleVersionCm100
OBJECT-TYPE
This object identifies the bundled firmware version for CM-100 modules.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.3DisplayStringread-onlycurrent
firmwareUpdateBundleVersionCm110
OBJECT-TYPE
This object identifies the bundled firmware version for CM-110 modules.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.4DisplayStringread-onlycurrent
firmwareUpdateBundleVersionCm1000OrCm1000Sfp
OBJECT-TYPE
This object identifies the bundled firmware version for CM-1000 or CM-1000-SFP modules.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.5DisplayStringread-onlycurrent
firmwareUpdateBundleVersionCm1110
OBJECT-TYPE
This object identifies the bundled firmware version for CM-1110 modules.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.6DisplayStringread-onlycurrent
firmwareUpdateBundleVersionCm1110Sfp
OBJECT-TYPE
This object identifies the bundled firmware version for CM-1110-SFP modules.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.7DisplayStringread-onlycurrent
firmwareUpdateBundleVersionCm100mm
OBJECT-TYPE
This object identifies the bundled firmware version for CM-100MM modules.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.8DisplayStringread-onlycurrent
firmwareUpdateBundleVersionCm1000mm
OBJECT-TYPE
This object identifies the bundled firmware version for CM-1000MM modules.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.9DisplayStringread-onlycurrent
firmwareUpdateBundleVersionCm10g
OBJECT-TYPE
This object identifies the bundled firmware version for CM-10G modules.
1.3.6.1.4.1.1966.21.1.1.1.2.6.2.10DisplayStringread-onlycurrent
nettxfrTable
OBJECT-TYPE
Table of snmp file transfer sessions.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3not-accessiblecurrent
nettxfrEntry
OBJECT-TYPE
Entries of the table, each relating to a SNMP file transfer session.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1not-accessiblecurrent
nettxfrSessionID
OBJECT-TYPE
This indicates if the net transfer is to be loaded to the management module or saved from the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.1Unsigned32not-accessiblecurrent
nettxfrStatus
OBJECT-TYPE
This field indicates the status of the nettxfr process. A value of start(1) should be written to this field to start the nettxfr process with the specified parameters in the rest of this group.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.2INTEGER {fileNotFound(-3), busy(-2), error(-1), idle(0), start(1), transferringFile(2), erassingFlash(3), programmingFlash(4), verifyingFlash(5), moduleReset(6), processingScriptFile(7), finished(8)}read-writecurrent
nettxfrDirection
OBJECT-TYPE
This indicates if the net transfer is to be loaded to the management module or saved from the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.3INTEGER {load(0), save(1)}read-writecurrent
nettxfrFileType
OBJECT-TYPE
This indicates the type of file to be transfered to/from the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.4INTEGER {configuration(0), firmware(1), media-converter(2), script(3), serialt-buf(4), ssh-server(5), ssl(6), text-config(7), diagnostic-file(8), sntp-keys(9)}read-writecurrent
nettxfrFileHost
OBJECT-TYPE
The host name or IP address of the server that contains the file to be transfered to/from the management module.. If you use a host name, it must exist in the management module's host table or be resolved by DNS.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.5DisplayString (SIZE(0..46))read-writecurrent
nettxfrFileName
OBJECT-TYPE
The path and file name (do not use a drive letter), relative to the default path of your TFTP server software, of the file to be transfered to/from the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.6DisplayString (SIZE(0..64))read-writecurrent
nettxfrMCSlotNumber
OBJECT-TYPE
Specifies the slot number of the Media Converter Module to which the firmware will be transfered.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.7SlotNumberread-writecurrent
nettxfrUserName
OBJECT-TYPE
Specifies the user login name who owns the ssh public key that is to be transfered to the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.8DisplayString (SIZE(0..64))read-writecurrent
nettxfrSSHKeyType
OBJECT-TYPE
Specifies the authentication method used by the ssh-server public key that is to be transfered to/from the management module
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.9INTEGER {dsa(0), rsa(1)}read-writecurrent
nettxfrSSLType
OBJECT-TYPE
Specifies the type of SSL file to be transfered to the management module. These files are needed if you are using the secure version of the WebManager (HTTPS), or LDAP authentication with TLS.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.10INTEGER {ca-list(0), certificate(1), private-key(2)}read-writecurrent
nettxfrSessionInUse
OBJECT-TYPE
Specifies whether this net transfer session entry is in use. If a manager tries to write a 1 to this field and the session is already in use, then an error is returned.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.11INTEGER {idle(0), in-use(1)}read-writecurrent
nettxfrTftpPort
OBJECT-TYPE
Specifies a UDP port number for the TFTP host server. Default is 69.
1.3.6.1.4.1.1966.21.1.1.1.2.6.3.1.12Unsigned32 (1..65536)read-writecurrent
mgtAdminGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.7
adminFunction
OBJECT-TYPE
Perform a specific function on the management module. If you want to save all the changes that have been submitted to the management module, you need to expand the adminGroup container folder and SET the adminFunction to 1 to write to FLASH. To make the configuration changes take effect, SET the adminFunction to 3 to reboot the management module.
1.3.6.1.4.1.1966.21.1.1.1.2.7.1INTEGER {writeToFlash(1), resetToFactoryDefaults(2), reboot(3), resetSecurIDNodeSecret(4)}read-writecurrent
adminLastFunction
OBJECT-TYPE
The last function requested
1.3.6.1.4.1.1966.21.1.1.1.2.7.2INTEGER {writeToFlash(1), resetToFactoryDefaults(2), reboot(3), resetSecurIDNodeSecret(4)}read-onlycurrent
adminStatus
OBJECT-TYPE
The status of the last function performed.
1.3.6.1.4.1.1966.21.1.1.1.2.7.3INTEGER {successful(0), error(1), inProgress(2)}read-onlycurrent
adminbootReason
OBJECT-TYPE
The reason(s) why the management module last rebooted.
1.3.6.1.4.1.1966.21.1.1.1.2.7.4Bits {bootCrash(29), bootWarmStart(30), bootNormal(31)}read-onlycurrent
adminDiagFileAvailable
OBJECT-TYPE
This object indicates that a diagnostic file is available.
1.3.6.1.4.1.1966.21.1.1.1.2.7.5YesNoValueread-onlycurrent
mgtDisplayFormatGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.8
displayFormatStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.8.1ContainerStatusread-writecurrent
cfgTemperatureUnits
OBJECT-TYPE
This object identifies the units to display any internally measured temperature. The units can be Celsius or Fahrenheit.
1.3.6.1.4.1.1966.21.1.1.1.2.8.2INTEGER {celsius(0), fahrenheit(1)}read-writecurrent
cfgSfpPowerUnits
OBJECT-TYPE
This object identifies the units to display any SFP DMI internally measured transmit/receive power. The units can be milliwatts (mW) or Decibel milliwatts (dBm).
1.3.6.1.4.1.1966.21.1.1.1.2.8.3INTEGER {milliwats(0), decibelmilliwatts(1)}read-writecurrent
cfgTimeFormat
OBJECT-TYPE
This object identifies the format to display the time.
1.3.6.1.4.1.1966.21.1.1.1.2.8.4INTEGER {time12HourFmt(0), time24HourFmt(1)}read-writecurrent
cfgDateFormat
OBJECT-TYPE
This object identifies the format to display date.
1.3.6.1.4.1.1966.21.1.1.1.2.8.5INTEGER {dateMonthDayYearFmt(0), dateDayMonthYearFmt(1), dateYearMonthDayFmt(2)}read-writecurrent
mgtChassisCfgGroup
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.1.2.9
mgtChassisSlotPowerScheduleTable
OBJECT-TYPE
Table of power schedule configuration for chassis slots. (Not applicable to 2-slot chassis.)
1.3.6.1.4.1.1966.21.1.1.1.2.9.1not-accessiblecurrent
mgtChassisSlotPowerScheduleEntry
OBJECT-TYPE
Entries of the table, each relating to a separate slot in a chassis.
1.3.6.1.4.1.1966.21.1.1.1.2.9.1.1not-accessiblecurrent
powerSchedSlotIndex
OBJECT-TYPE
This object identifies the chassis slot number.
1.3.6.1.4.1.1966.21.1.1.1.2.9.1.1.2SlotNumbernot-accessiblecurrent
powerSchedDayOfWeek
OBJECT-TYPE
This object identifies the day of the week.
1.3.6.1.4.1.1966.21.1.1.1.2.9.1.1.3INTEGER {sunday(1), monday(2), tuesday(3), wednesday(4), thursday(5), friday(6), saturday(7)}not-accessiblecurrent
powerSchedConifgStatus
OBJECT-TYPE
When you perform a GET on this variable, one of the following values will be returned: 1-Indicates that the container folder is active with no changes. 2-Indicates that the container folder is active with change(s). Once you have completed setting the variables in a folder, you will want to submit your changes to the management module. To do this, set the Status variable to 4. If you want to discard the changes, set the Status variable to 6. 4-Indicates that the changes in the container folder are to be submitted to the management module and verified. To save the changes to flash a write of writeToFlash(1) in the adminFunction object is required. 6-Indicates that the changes in the container folder are to be discarded.
1.3.6.1.4.1.1966.21.1.1.1.2.9.1.1.4ContainerStatusread-writecurrent
powerSchedOnHour
OBJECT-TYPE
This object identifies the hour (0-23) of the day to schedule a power on of the chassis slot
1.3.6.1.4.1.1966.21.1.1.1.2.9.1.1.5INTEGER (0..23)read-writecurrent
powerSchedOnMinute
OBJECT-TYPE
This object identifies the minute (0-59) of the hour to schedule a power on of the chassis slot
1.3.6.1.4.1.1966.21.1.1.1.2.9.1.1.6INTEGER (0..59)read-writecurrent
powerSchedOffHour
OBJECT-TYPE
This object identifies the hour (0-23) of the day to schedule a power off of the chassis slot
1.3.6.1.4.1.1966.21.1.1.1.2.9.1.1.7INTEGER (0..23)read-writecurrent
powerSchedOffMinute
OBJECT-TYPE
This object identifies the minute (0-59) of the hour to schedule a power off of the chassis slot
1.3.6.1.4.1.1966.21.1.1.1.2.9.1.1.8INTEGER (0..59)read-writecurrent
mcrMGTMIBConformance
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.2
mcrMGTMIBCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.2.1
mcrMGTMIBGroups
OBJECT-IDENTITY
1.3.6.1.4.1.1966.21.1.1.2.2

Notifications

NameOIDStatus
mcrMgtModuleInserted
NOTIFICATION-TYPE
Trap being sent indicates that a management module has been inserted int the chassis.
1.3.6.1.4.1.1966.21.1.1.0.1current
mcrMgtSystemBoot
NOTIFICATION-TYPE
Trap being sent indicates that the management module's system firmware is being booted up and has completed system initialization. In some case this alert will indicate a cold start like a user resetting the management module or warm start if the module automatically resets because of a detected crash.
1.3.6.1.4.1.1966.21.1.1.0.2current
mcrMgtReset
NOTIFICATION-TYPE
Trap being sent indicates that the management module has been manually reset via the reset button or one of the managers.
1.3.6.1.4.1.1966.21.1.1.0.3current
mcrMgtResetFactory
NOTIFICATION-TYPE
Trap being sent indicates that the management module has been manually reset to factory by holding the reset button for 3 or more seconds, or one of the managers. This means that any files downloaded to the management module will be erase and the management configuration file is reset back to the default configuration.
1.3.6.1.4.1.1966.21.1.1.0.4current
mcrMgtEtheLinkUp
NOTIFICATION-TYPE
Trap being sent indicates that the current link status of the Ethernet port on the management module is up.
1.3.6.1.4.1.1966.21.1.1.0.5current
mcrMgtEtheLinkDown
NOTIFICATION-TYPE
Trap being sent indicates that the current link status of the Ethernet port on the management module is down.
1.3.6.1.4.1.1966.21.1.1.0.6current
mcrMgtConMonDSRSigChg
NOTIFICATION-TYPE
Trap being sent indicates that monitor console DSR is configured and the status of one of these signal has changed on the console port.
1.3.6.1.4.1.1966.21.1.1.0.7current
mcrMgtAuthFail
NOTIFICATION-TYPE
Trap being sent indicates that a user failed authentication via Telnet, SSH, WebManager, SNMP or the serial console.
1.3.6.1.4.1.1966.21.1.1.0.8current
mcrMgtAuthSuccess
NOTIFICATION-TYPE
Trap being sent indicates that a user failed authentication via Telnet, SSH, WebManager or the serial console.
1.3.6.1.4.1.1966.21.1.1.0.9current
mcrMgtDateTimeChg
NOTIFICATION-TYPE
Trap being sent indicates that the system date and/or time has been changed.
1.3.6.1.4.1.1966.21.1.1.0.10current
mcrMgtSntpServFail
NOTIFICATION-TYPE
Trap being sent indicates that SNTP is configured and the management module can not communicate with the configured SNTP server.
1.3.6.1.4.1.1966.21.1.1.0.11current
mcrMgtSntpServRec
NOTIFICATION-TYPE
Trap being sent indicates that the SNTP is configured and the management module has recovered communications with the configured SNTP server.
1.3.6.1.4.1.1966.21.1.1.0.12current
mcrMgtSnmpTrapHostFail
NOTIFICATION-TYPE
Trap being sent indicates that SNMP traps is and the management module can not communicate with the configured SNMP trap host. This trap will only be sent for SNMP trap hosts configured for 'Inform' type traps.
1.3.6.1.4.1.1966.21.1.1.0.13current
mcrMgtSnmpTrapHostRec
NOTIFICATION-TYPE
Trap being sent indicates that SNMP traps is and the management module has recovered communications with the configured SNMP trap host.
1.3.6.1.4.1.1966.21.1.1.0.14current
mcrMgtEmailServFail
NOTIFICATION-TYPE
Trap being sent indicates that an alert email server is configured and the management module can not communicate with the configured email server.
1.3.6.1.4.1.1966.21.1.1.0.15current
mcrMgtEmailServRec
NOTIFICATION-TYPE
Trap being sent indicates that an alert email server is configured and the management module has recovered communications with the configured email server.
1.3.6.1.4.1.1966.21.1.1.0.16current
mcrMgtConfSavedFlash
NOTIFICATION-TYPE
Trap being sent indicates that the configuration has been saved to flash on the management module.
1.3.6.1.4.1.1966.21.1.1.0.17current
mcrMgtIpAddrDynChg
NOTIFICATION-TYPE
Trap being sent indicates that the system IP address has been dynamically changed.
1.3.6.1.4.1.1966.21.1.1.0.18current
mcrMgtTftpUploadFail
NOTIFICATION-TYPE
Trap being sent indicates that an attempt to transfer a file via TFTP, off the management module to a remote host has failed.
1.3.6.1.4.1.1966.21.1.1.0.19current
mcrMgtTftpUploadSuccess
NOTIFICATION-TYPE
Trap being sent indicates that an attempt to transfer a file via TFTP, off the management module to a remote host was successful.
1.3.6.1.4.1.1966.21.1.1.0.20current
mcrMgtTftpDownloadFail
NOTIFICATION-TYPE
Trap being sent indicates that an attempt to transfer a file via TFTP, from a remote host to the management module has failed.
1.3.6.1.4.1.1966.21.1.1.0.21current
mcrMgtTftpDownloadSuccess
NOTIFICATION-TYPE
Trap being sent indicates that an attempt to transfer a file via TFTP, from a remote host to the management module was successful.
1.3.6.1.4.1.1966.21.1.1.0.22current
mcrMgtChassisMismatch
NOTIFICATION-TYPE
Trap being sent indicates that the management module has been inserted into a chassis that does not match it's Backup media converter module configuration. Backup media module configurations will be reset to factory default.
1.3.6.1.4.1.1966.21.1.1.0.23current
mcrChassisAdd
NOTIFICATION-TYPE
Trap being sent indicates that a new chassis as been added to the chain of chassis.
1.3.6.1.4.1.1966.21.1.1.0.24current
mcrChassisRemove
NOTIFICATION-TYPE
Trap being sent indicates that that a chassis has been removed from the chain of chassis.
1.3.6.1.4.1.1966.21.1.1.0.25current
mcrChassisReset
NOTIFICATION-TYPE
Trap being sent indicates that the chassis back-plane has been manually reset by a user managing the unit.
1.3.6.1.4.1.1966.21.1.1.0.26current
mcrChassisTemperatureAlarm
NOTIFICATION-TYPE
Trap being sent indicates that the chassis temperature has exceeded the configured high temperature threshold temperature.
1.3.6.1.4.1.1966.21.1.1.0.27current
mcrChassisTemperatureRecover
NOTIFICATION-TYPE
Trap being sent indicates that the chassis temperature has recovered back to normal operating temperature.
1.3.6.1.4.1.1966.21.1.1.0.28current
mcrChassisSlotPoweredOn
NOTIFICATION-TYPE
Trap being sent indicates that the chassis slot has been powered off either manually or through the configured chassis slot power schedule.
1.3.6.1.4.1.1966.21.1.1.0.29current
mcrChassisSlotPoweredOff
NOTIFICATION-TYPE
Trap being sent indicates that the chassis slot has been powered on either manually or through the configured chassis slot power schedule.
1.3.6.1.4.1.1966.21.1.1.0.30current
mcrChassisFail
NOTIFICATION-TYPE
Trap being sent indicates that the management module has detected a failure condition in the chassis.
1.3.6.1.4.1.1966.21.1.1.0.31current
mcrChassisOk
NOTIFICATION-TYPE
Trap being sent indicates that the chassis has recovered from a failure and is now operating normally.
1.3.6.1.4.1.1966.21.1.1.0.32current
mcrPsmuInserted
NOTIFICATION-TYPE
Trap being sent indicates that a power supply has been inserted into the chassis.
1.3.6.1.4.1.1966.21.1.1.0.33current
mcrPsmuRemoved
NOTIFICATION-TYPE
Trap being sent indicates that a power supply's has been removed from the chassis.
1.3.6.1.4.1.1966.21.1.1.0.34current
mcrPsmuPsuFail
NOTIFICATION-TYPE
Trap being sent indicates that the power supply has failed it's self-test diagnostics.
1.3.6.1.4.1.1966.21.1.1.0.35current
mcrPsmuPsuOk
NOTIFICATION-TYPE
Trap being sent indicates that the power supply has passed it's self-test diagnostics.
1.3.6.1.4.1.1966.21.1.1.0.36current
mcrPsmuPsuVoltageFail
NOTIFICATION-TYPE
Trap being sent indicates that the voltage being supplied by the indicated power supply is insufficient.
1.3.6.1.4.1.1966.21.1.1.0.37current
mcrPsmuPsuVoltageOk
NOTIFICATION-TYPE
Trap being sent indicates that the voltage being supplied by the indicated power supply is now in the normal operating range.
1.3.6.1.4.1.1966.21.1.1.0.38current
mcrPsmuFanFail
NOTIFICATION-TYPE
Trap being sent indicates that the fan has failed.
1.3.6.1.4.1.1966.21.1.1.0.39current
mcrPsmuFanOk
NOTIFICATION-TYPE
Trap being sent indicates that the fan currently operating normally.
1.3.6.1.4.1.1966.21.1.1.0.40current
mcrMediaInserted
NOTIFICATION-TYPE
Trap being sent indicates that a media converter module has been inserted into the chassis.
1.3.6.1.4.1.1966.21.1.1.0.42current
mcrMediaRemoved
NOTIFICATION-TYPE
Trap being sent indicates that a media converter module has been removed from the chassis.
1.3.6.1.4.1.1966.21.1.1.0.43current
mcrMediaReset
NOTIFICATION-TYPE
Trap being sent indicates that the media converter module has been manually reset by a user managing the unit.
1.3.6.1.4.1.1966.21.1.1.0.44current
mcrMediaLostCommunication
NOTIFICATION-TYPE
Trap being sent indicates that the management module can no longer communicate with the media converter module
1.3.6.1.4.1.1966.21.1.1.0.45current
mcrMediaRecovCommunication
NOTIFICATION-TYPE
Trap being sent indicates that the management module recovered communication with a media converter module
1.3.6.1.4.1.1966.21.1.1.0.46current
mcrMediaFail
NOTIFICATION-TYPE
Trap being sent indicates that the media converter module has failed its self-test diagnostics
1.3.6.1.4.1.1966.21.1.1.0.47current
mcrMediaOk
NOTIFICATION-TYPE
Trap being sent indicates that the media converter module has passed its self-test diagnostics
1.3.6.1.4.1.1966.21.1.1.0.48current
mcrMediaLinkUp
NOTIFICATION-TYPE
Trap being sent indicates that the current link status of the Fiber or Copper port on the media converter module is up.
1.3.6.1.4.1.1966.21.1.1.0.49current
mcrMediaLinkDown
NOTIFICATION-TYPE
Trap being sent indicates that the current link status of the Fiber or Copper port on the media converter module is down.
1.3.6.1.4.1.1966.21.1.1.0.50current
mcrMediaConfUpdateFail
NOTIFICATION-TYPE
Trap being sent indicates that the configuration update on the media converter module has failed.
1.3.6.1.4.1.1966.21.1.1.0.51current
mcrMediaConfUpdateSuccess
NOTIFICATION-TYPE
Trap being sent indicates that the configuration update on the media converter module was successful. The media converter module configuration can be updated manually or automatically.
1.3.6.1.4.1.1966.21.1.1.0.52current
mcrMediaConfMismatch
NOTIFICATION-TYPE
Trap being sent indicates that a chassis slot is configured with Backup/Restore and the media converter module type configured for the slot does not match the media converter module type inserted into the slot.
1.3.6.1.4.1.1966.21.1.1.0.53current
mcrMediaConfMismatchResolv
NOTIFICATION-TYPE
Trap being sent indicates that a user has taken action to resolved media converter module configuration mismatch
1.3.6.1.4.1.1966.21.1.1.0.54current
mcrMediaFirmwareUpdateFail
NOTIFICATION-TYPE
Trap being sent indicates that an attempt to update a media converter module's firmware has Failed.
1.3.6.1.4.1.1966.21.1.1.0.55current
mcrMediaFirmwareUpdateSuccess
NOTIFICATION-TYPE
Trap being sent indicates that an attempt to update a media converter module's firmware was successful.
1.3.6.1.4.1.1966.21.1.1.0.56current
mcrSfpInserted
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module has been inserted into a media converter module
1.3.6.1.4.1.1966.21.1.1.0.57current
mcrSfpRemoved
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module has been removed from a media converter module
1.3.6.1.4.1.1966.21.1.1.0.58current
mcrSfpHighTempWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's temperature has exceeded the high temperature warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.59current
mcrSfpHighTempWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's temperature has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.60current
mcrSfpHighTempAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's temperature has exceeded the high temperature alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.61current
mcrSfpHighTempAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's temperature has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.62current
mcrSfpLowTempWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's temperature has gone below the low temperature warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.63current
mcrSfpLowTempWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's temperature has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.64current
mcrSfpLowTempAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's temperature has gone below the low temperature alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.65current
mcrSfpLowTempAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's temperature has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.66current
mcrSfpHighVoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's voltage has exceeded the high voltage warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.67current
mcrSfpHighVoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's voltage has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.68current
mcrSfpHighVoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's voltage has exceeded the high voltage alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.69current
mcrSfpHighVoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's voltage has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.70current
mcrSfpLowVoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's voltage has gone below the low voltage warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.71current
mcrSfpLowVoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's voltage has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.72current
mcrSfpLowVoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's voltage has gone below the low voltage alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.73current
mcrSfpLowVoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's voltage has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.74current
mcrSfpHighTxBiasWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX Bias current has exceeded the high TX Bias current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.75current
mcrSfpHighTxBiasWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX Bias current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.76current
mcrSfpHighTxBiasAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX Bias current has exceeded the high TX Bias current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.77current
mcrSfpHighTxBiasAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX Bias current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.78current
mcrSfpLowTxBiasWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX Bias current has gone below the low Tx Bias current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.79current
mcrSfpLowTxBiasWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX Bias current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.80current
mcrSfpLowTxBiasAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX Bias current has gone below the low Tx Bias current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.81current
mcrSfpLowTxBiasAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX Bias current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.82current
mcrSfpHighTxPowerWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX power has exceeded the high TX power warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.83current
mcrSfpHighTxPowerWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX power has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.84current
mcrSfpHighTxPowerAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX power has exceeded the high TX power alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.85current
mcrSfpHighTxPowerAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX power has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.86current
mcrSfpLowTxPowerWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX power has gone below the low TX power warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.87current
mcrSfpLowTxPowerWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX power has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.88current
mcrSfpLowTxPowerAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX power has gone below the low TX power alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.89current
mcrSfpLowTxPowerAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's TX power has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.90current
mcrSfpHighRxPowerWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's RX power has exceeded the high RX power warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.91current
mcrSfpHighRxPowerWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's RX power has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.92current
mcrSfpHighRxPowerAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's RX power has exceeded the high RX power alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.93current
mcrSfpHighRxPowerAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's RX power has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.94current
mcrSfpLowRxPowerWarn
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's RX power has gone below the low RX power warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.95current
mcrSfpLowRxPowerWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's RX power has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.96current
mcrSfpLowRxPowerAlarm
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's RX power has gone below the low RX power alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.97current
mcrSfpLowRxPowerAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that a SFP module's RX power has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.98current
mcrChassisCommTempSensorFail
NOTIFICATION-TYPE
Trap being sent indicates that communication with the chassis temperature sensor has failed. The current chassis temperature reading will be unknown
1.3.6.1.4.1.1966.21.1.1.0.99current
mcrChassisCommTempSensorRecov
NOTIFICATION-TYPE
Trap being sent indicates that communication with the chassis temperature sensor has recovered.
1.3.6.1.4.1.1966.21.1.1.0.100current
mcrMediaDetectFail
NOTIFICATION-TYPE
Trap being sent indicates that the indicated media card is being powered down due to the detection of a hardware failure.
1.3.6.1.4.1.1966.21.1.1.0.101current
mcrMediaBadImage
NOTIFICATION-TYPE
Trap being sent indicates that the CRC of the media converter module firmware is incorrect. This can be caused if there is no image on the module or the image is corrupt.
1.3.6.1.4.1.1966.21.1.1.0.102current
mcrSfpLostComm
NOTIFICATION-TYPE
Trap being sent indicates that the media converter module's microcode can no longer communicate with the SFP module.
1.3.6.1.4.1.1966.21.1.1.0.103current
mcrSfpRecovComm
NOTIFICATION-TYPE
Trap being sent indicates that the media converter module's microcode had previously lost communication with, but has now regained communication with the SFP module.
1.3.6.1.4.1.1966.21.1.1.0.104current
mcrModuleNotSupported
NOTIFICATION-TYPE
Trap being sent indicates that the media converter module is not fully supported by the management module. Update the management module firmware to rectify this issue.
1.3.6.1.4.1.1966.21.1.1.0.105current
mcrModuleFirmwareUpdate
NOTIFICATION-TYPE
Trap being sent indicates that the media converter module firmware is being updated.
1.3.6.1.4.1.1966.21.1.1.0.106current
mcrSfpPortShutdown
NOTIFICATION-TYPE
Trap being sent indicates that the Sfp/Xfp port has been shutdown due to high temperature.
1.3.6.1.4.1.1966.21.1.1.0.107current
mcrSfpPortShutdownRecov
NOTIFICATION-TYPE
Trap being sent indicates that the Sfp/Xfp port shutdown has recovered.
1.3.6.1.4.1.1966.21.1.1.0.108current
mcrXfpHighApdBiasWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's APD Bias Current has exceeded the high APD Bias warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.109current
mcrXfpHighApdBiasWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's APD Bias Current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.110current
mcrXfpHighApdBiasAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's APD Bias Current has exceeded the high APD Bias alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.111current
mcrXfpHighApdBiasAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's APD Bias Current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.112current
mcrXfpLowApdBiasWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's APD Bias Current has gone below the low APD Bias warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.113current
mcrXfpLowApdBiasWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's APD Bias Current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.114current
mcrXfpLowApdBiasAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's APD Bias Current has gone below the low APD Bias alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.115current
mcrXfpLowApdBiasAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's APD Bias Current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.116current
mcrXfpHighTecCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's TEC Current has exceeded the high TEC Current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.117current
mcrXfpHighTecCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's TEC Current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.118current
mcrXfpHighTecCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's TEC Current has exceeded the high TEC Current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.119current
mcrXfpHighTecCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's TEC Current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.120current
mcrXfpLowTecCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's TEC Current has gone below the low TEC Current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.121current
mcrXfpLowTecCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's TEC Current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.122current
mcrXfpLowTecCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's TEC Current has gone below the low TEC Current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.123current
mcrXfpLowTecCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's TEC Current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.124current
mcrXfpHighLaserTempWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Temperature has exceeded the high Laser Temperature warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.125current
mcrXfpHighLaserTempWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Temperature has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.126current
mcrXfpHighLaserTempAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Temperature has exceeded the high Laser Temperature alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.127current
mcrXfpHighLaserTempAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Temperature has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.128current
mcrXfpLowLaserTempWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Temperature has gone below the low Laser Temperature warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.129current
mcrXfpLowLaserTempWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Temperature has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.130current
mcrXfpLowLaserTempAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Temperature has gone below the low Laser Temperature alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.131current
mcrXfpLowLaserTempAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Temperature has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.132current
mcrXfpHighLaserWavelengthWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Wavelength has exceeded the high Laser Wavelength warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.133current
mcrXfpHighLaserWavelengthWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Wavelength has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.134current
mcrXfpHighLaserWavelengthAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Wavelength has exceeded the high Laser Wavelength alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.135current
mcrXfpHighLaserWavelengthAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Wavelength has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.136current
mcrXfpLowLaserWavelengthWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Wavelength has gone below the low Laser Wavelength warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.137current
mcrXfpLowLaserWavelengthWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Wavelength has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.138current
mcrXfpLowLaserWavelengthAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Wavelength has gone below the low Laser Wavelength alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.139current
mcrXfpLowLaserWavelengthAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's Laser Wavelength has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.140current
mcrXfpHigh5VoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has exceeded the high +5v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.141current
mcrXfpHigh5VoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.142current
mcrXfpHigh5VoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has exceeded the high +5v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.143current
mcrXfpHigh5VoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.144current
mcrXfpLow5VoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has gone below the low +5v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.145current
mcrXfpLow5VoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.146current
mcrXfpLow5VoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has gone below the low +5v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.147current
mcrXfpLow5VoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.148current
mcrXfpHigh33VoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has exceeded the high +3.3v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.149current
mcrXfpHigh33VoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.150current
mcrXfpHigh33VoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has exceeded the high +3.3v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.151current
mcrXfpHigh33VoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.152current
mcrXfpLow33VoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has gone below the low +3.3v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.153current
mcrXfpLow33VoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.154current
mcrXfpLow33VoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has gone below the low +3.3v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.155current
mcrXfpLow33VoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.156current
mcrXfpHigh18VoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has exceeded the high +1.8v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.157current
mcrXfpHigh18VoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.158current
mcrXfpHigh18VoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has exceeded the high +1.8v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.159current
mcrXfpHigh18VoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.160current
mcrXfpLow18VoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has gone below the low +1.8v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.161current
mcrXfpLow18VoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.162current
mcrXfpLow18VoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has gone below the low +1.8v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.163current
mcrXfpLow18VoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.164current
mcrXfpHighM52VoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has exceeded the high -5.2v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.165current
mcrXfpHighM52VoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.166current
mcrXfpHighM52VoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has exceeded the high -5.2v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.167current
mcrXfpHighM52VoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.168current
mcrXfpLowM52VoltWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has gone below the low -5.2v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.169current
mcrXfpLowM52VoltWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.170current
mcrXfpLowM52VoltAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has gone below the low -5.2v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.171current
mcrXfpLowM52VoltAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.172current
mcrXfpHigh5VCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply current has exceeded the high +5v supply current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.173current
mcrXfpHigh5VCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.174current
mcrXfpHigh5VCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply current has exceeded the high +5v supply current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.175current
mcrXfpHigh5VCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.176current
mcrXfpLow5VCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply current has gone below the low +5v supply current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.177current
mcrXfpLow5VCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.178current
mcrXfpLow5VCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply current has gone below the low +5v supply current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.179current
mcrXfpLow5VCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.180current
mcrXfpHigh33VCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply current has exceeded the high +3.3v supply current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.181current
mcrXfpHigh33VCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.182current
mcrXfpHigh33VCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply current has exceeded the high +3.3v supply current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.183current
mcrXfpHigh33VCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.184current
mcrXfpLow33VCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply current has gone below the low +3.3v supply current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.185current
mcrXfpLow33VCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.186current
mcrXfpLow33VCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply current has gone below the low +3.3v supply current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.187current
mcrXfpLow33VCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.188current
mcrXfpHigh18VCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply current has exceeded the high +1.8v supply current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.189current
mcrXfpHigh18VCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.190current
mcrXfpHigh18VCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply current has exceeded the high +1.8v supply current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.191current
mcrXfpHigh18VCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.192current
mcrXfpLow18VCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply current has gone below the low +1.8v supply current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.193current
mcrXfpLow18VCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.194current
mcrXfpLow18VCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply current has gone below the low +1.8v supply current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.195current
mcrXfpLow18VCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.196current
mcrXfpHighM52VCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply current has exceeded the high -5.2v supply current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.197current
mcrXfpHighM52VCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.198current
mcrXfpHighM52VCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply current has exceeded the high -5.2v supply current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.199current
mcrXfpHighM52VCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.200current
mcrXfpLowM52VCurrentWarn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply current has gone below the low -5.2v supply current warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.201current
mcrXfpLowM52VCurrentWarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.202current
mcrXfpLowM52VCurrentAlarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply current has gone below the low -5.2v supply current alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.203current
mcrXfpLowM52VCurrentAlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply current has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.204current
mcrXfpHighVCC5Warn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has exceeded the high +5v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.205current
mcrXfpHighVCC5WarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.206current
mcrXfpHighVCC5Alarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has exceeded the high +5v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.207current
mcrXfpHighVCC5AlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.208current
mcrXfpLowVCC5Warn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has gone below the low +5v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.209current
mcrXfpLowVCC5WarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.210current
mcrXfpLowVCC5Alarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has gone below the low +5v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.211current
mcrXfpLowVCC5AlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +5v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.212current
mcrXfpHighVCC3Warn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has exceeded the high +3.3v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.213current
mcrXfpHighVCC3WarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.214current
mcrXfpHighVCC3Alarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has exceeded the high +3.3v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.215current
mcrXfpHighVCC3AlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.216current
mcrXfpLowVCC3Warn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has gone below the low +3.3v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.217current
mcrXfpLowVCC3WarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.218current
mcrXfpLowVCC3Alarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has gone below the low +3.3v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.219current
mcrXfpLowVCC3AlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +3.3v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.220current
mcrXfpHighVCC2Warn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has exceeded the high +1.8v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.221current
mcrXfpHighVCC2WarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.222current
mcrXfpHighVCC2Alarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has exceeded the high +1.8v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.223current
mcrXfpHighVCC2AlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.224current
mcrXfpLowVCC2Warn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has gone below the low +1.8v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.225current
mcrXfpLowVCC2WarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.226current
mcrXfpLowVCC2Alarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has gone below the low +1.8v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.227current
mcrXfpLowVCC2AlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's +1.8v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.228current
mcrXfpHighVEE5Warn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has exceeded the high -5.2v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.229current
mcrXfpHighVEE5WarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.230current
mcrXfpHighVEE5Alarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has exceeded the high -5.2v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.231current
mcrXfpHighVEE5AlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.232current
mcrXfpLowVEE5Warn
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has gone below the low -5.2v supply warning threshold.
1.3.6.1.4.1.1966.21.1.1.0.233current
mcrXfpLowVEE5WarnRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.234current
mcrXfpLowVEE5Alarm
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has gone below the low -5.2v supply alarm threshold.
1.3.6.1.4.1.1966.21.1.1.0.235current
mcrXfpLowVEE5AlarmRecov
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's -5.2v supply has recovered to normal operating level.
1.3.6.1.4.1.1966.21.1.1.0.236current
mcrSfpSpeedMismatch
NOTIFICATION-TYPE
Trap being sent indicates that there is a speed mismatch between the two SFP modules installed in the media converter.
1.3.6.1.4.1.1966.21.1.1.0.237current
mcrSfpSpeedMismatchRecov
NOTIFICATION-TYPE
Trap being sent indicates that the speed mismatch between the two SFP modules has recovered.
1.3.6.1.4.1.1966.21.1.1.0.238current
mcrXfpPowerExceeded
NOTIFICATION-TYPE
Trap being sent indicates that an XFP module's power requirements has exceeded card capacity.
1.3.6.1.4.1.1966.21.1.1.0.239current
mcrXfpPowerExceededRecov
NOTIFICATION-TYPE
Trap being sent indicates that the XFP excessive power alarm has recovered.
1.3.6.1.4.1.1966.21.1.1.0.240current
mcrLinkTestError
NOTIFICATION-TYPE
Trap being sent indicates that the link test running on the media converter has detected errors.
1.3.6.1.4.1.1966.21.1.1.0.241current
mcrAlarmRelayEngaged
NOTIFICATION-TYPE
Trap being sent indicates that the chassis alarm relay has engaged
1.3.6.1.4.1.1966.21.1.1.0.242current
mcrAlarmRelayDisengaged
NOTIFICATION-TYPE
Trap being sent indicates that the chassis alarm relay has disengaged
1.3.6.1.4.1.1966.21.1.1.0.243current
mcrBandwidthLevelUpstreamLow
NOTIFICATION-TYPE
Trap being sent indicates the media port is in a low upstream bandwidth condition. This happens when the bandwidth is below the configured threshold.
1.3.6.1.4.1.1966.21.1.1.0.244current
mcrBandwidthLevelUpstreamRecov
NOTIFICATION-TYPE
Trap being sent indicates the media port has recovered from a low upstream bandwidth condition.
1.3.6.1.4.1.1966.21.1.1.0.245current
mcrBandwidthLevelDownstreamLow
NOTIFICATION-TYPE
Trap being sent indicates the media port is in a low downstream bandwidth condition. This happens when the bandwidth is below the configured threshold.
1.3.6.1.4.1.1966.21.1.1.0.246current
mcrBandwidthLevelDownstreamRecov
NOTIFICATION-TYPE
Trap being sent indicates the media port has recovered from a low downstream bandwidth condition.
1.3.6.1.4.1.1966.21.1.1.0.247current
mcrMediaRemoteReset
NOTIFICATION-TYPE
Trap being sent indicates that the media converter module's peer has been manually reset by a user managing the unit.
1.3.6.1.4.1.1966.21.1.1.0.248current

Conformance

NameOIDStatus
mcrMGTMIBCompliance
MODULE-COMPLIANCE
The compliance statement for mcrMGT which implement the Perle Managed Media Converters MIB.
1.3.6.1.4.1.1966.21.1.1.2.1.1current
mcrMGTMIBChassisGroup
OBJECT-GROUP
The group of objects for identifying and determining the configuration and current timeliness values of the Perle Managed Media Converters chassis.
1.3.6.1.4.1.1966.21.1.1.2.2.1current
mcrMGTMIBMediaGroup
OBJECT-GROUP
The group of objects for identifying and determining the configuration and current timeliness values of the Perle Managed Media Converters media converter modules
1.3.6.1.4.1.1966.21.1.1.2.2.2current
mcrMGTMIBMgtGroup
OBJECT-GROUP
The group of objects for identifying and determining the configuration and current timeliness values of the Perle Managed Media Converters media converter modules
1.3.6.1.4.1.1966.21.1.1.2.2.3current
mcrMGTMIBNotificationsGroup
NOTIFICATION-GROUP
The group of notifications (traps) which is implemented for the Perle Managed Media Converters.
1.3.6.1.4.1.1966.21.1.1.2.2.4current