PDN-XDSL-INTERFACE-MIB
- Registered at
- 1.3.6.1.4.1.1795.2.24.9.21.3.6.1.4.1.1795.2.24.9.4
- Namespace
- zhone
- Source file
PDN-XDSL-INTERFACE-MIB- Digest
sha256:bed03161741c40cc3c216921b9904ba706d5e70e692bd93a30becfbfc98da7db
Imports
| From | Symbols |
|---|---|
| IF-MIB | ifIndex |
| PDN-HEADER-MIB | pdn-xdsl |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
IANAifType-MIB IF-MIB PDN-HEADER-MIB PDN-XDSL-INTERFACE-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| xdslIfConfigMIBObjects OBJECT-IDENTITY | 1.3.6.1.4.1.1795.2.24.9.2 | |||
| xdslDevGenericIfConfig OBJECT-IDENTITY | 1.3.6.1.4.1.1795.2.24.9.2.1 | |||
| xdslDevGenericIfConfigTable OBJECT-TYPE The xdslDevGenericIfConfigTable provides config information generic to a xDSL device, or system. The table is indexed by an object which corresponds to ifIndex. These ifIndex entries, themselves, denote and identify specific xdsl interfaces on the board or module. Also the configuration parameters are grouped into two broad categories, 'up' and 'down'. 'up' reflects the upstream direction (from the customer premises to the central office). 'Down' reflects the downstream direction (from the central office to the customer premises) | 1.3.6.1.4.1.1795.2.24.9.2.1.1 | not-accessible | mandatory | |
| xdslDevGenericIfConfigEntry OBJECT-TYPE Describes a specific xDSL interface entry. | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1 | not-accessible | mandatory | |
| xdslDevGenericIfConfigPortSpeedBehaviour OBJECT-TYPE The value of this object corresponds to the behaviour of the specified port. The default value for this object is fixed (1). | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.1 | INTEGER {fixed(1), adaptive(2)} | read-write | mandatory |
| xdslDevGenericIfConfigMarginThreshold OBJECT-TYPE The value of this object corresponds to the offset from the startup margin. The threshold margin is calculated by subtracting the offset from the startup margin. Permissible range of values are between -7 and 14. A value of -9999 disables the threshold check. The default value of this object is 3 | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.2 | INTEGER | read-write | mandatory |
| xdslDevGenericIfConfigPortID OBJECT-TYPE The value of this object corresponds to 40 character information only field that identifies what the DSL port is connected to (Circuit ID, MDF location, Customer name, etc.) | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.3 | DisplayString (SIZE(1..40)) | read-write | mandatory |
| xdslDevGenericIfConfigLinkUpDownTransitionThreshold OBJECT-TYPE The value of this object corresponds to the threshold value for link up-down transitions. If link up-down's exceed this threshold value a xdslLinkupDownTransitions trap is generated. This value would represent the number of link up-down transitions in a 15 minute interval. A value of -9999 disables the threshold check. The default value for this object is 0 | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.4 | INTEGER | read-write | mandatory |
| xdslDevGenericIfConfigLineEncodeType OBJECT-TYPE The value of this object corresponds to the line encoding technology used for data transmission over the the dsl link. | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.5 | INTEGER {other(1), cap(2), twoB1q(3), mvl(4), g-lite(5), dmt(6)} | read-only | mandatory |
| xdslDevGenericIfConfigLineRateMode OBJECT-TYPE The value of this object is used to choose the line rate list for data transmission over the dsl link. The default value is standard(1). | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.6 | INTEGER {standard(1), nx128(2)} | read-write | mandatory |
| xdslDevGenericIfConfigLinkEncapType OBJECT-TYPE The value of this object corresponds to the link encapsulation type. Following are valid settings: linkNone (1) ethernet (2) ppp (3) slip (4) frameRelay-PLL (5) x23PVC (6) x25SVC (7) hdlc (8) etherHDLC (9) rfc1483-MPOA (10) funi-MPOA (11) frf5 (12) frf8 (13) pppoAVC-Mux (14) pppoALLC (15) | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.7 | INTEGER {linkNone(1), ethernet(2), ppp(3), slip(4), frameRelay-PLL(5), x23PVC(6), x25SVC(7), hdlc(8), etherHDLC(9), rfc1483-MPOA(10), funi-MPOA(11), frf5(12), frf8(13), pppoAVC-Mux(14), pppoALLC(15)} | read-write | mandatory |
| xdslDevGenericIfConfigSnType OBJECT-TYPE The value of this object is used to choose a valid Service Node Type to be configured in the port. The configurable values are the object identifiers of the remote endpoints as defined in the xdsl-remote group of the pdn-xdsl-products. The following are examples of valid endpoints for the 8312 Reach port card: xdsl_6350, xdsl_6351, xdsl_6310 By default, this object will be set to the default service node associated with the portcard. | 1.3.6.1.4.1.1795.2.24.9.2.1.1.1.8 | OBJECT IDENTIFIER | read-write | mandatory |
| xdslDevRADSLSpecificIfConfig OBJECT-IDENTITY | 1.3.6.1.4.1.1795.2.24.9.2.2 | |||
| xdslDevRADSLSpecificIfConfigTable OBJECT-TYPE The xdslDevRADSLSpecificIfConfigTable provides config information specific to a xDSL device, or system. The table is indexed by an object which corresponds to ifIndex. These ifIndex entries, themselves, denote and identify specific xdsl interfaces on the board or module. Also the configuration parameters are grouped into two broad categories, 'up' and 'down'. 'up' reflects the upstream direction (from the customer premises to the central office). 'Down' reflects the downstream direction (from the central office to the customer premises) | 1.3.6.1.4.1.1795.2.24.9.2.2.1 | not-accessible | mandatory | |
| xdslDevRADSLSpecificIfConfigEntry OBJECT-TYPE Describes a specific xDSL interface entry. | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1 | not-accessible | mandatory | |
| xdslDevRADSLSpecificIfConfigUpFixedPortSpeed OBJECT-TYPE The value of this object corresponds to the upstream speed of the specified port for fixed port speed behaviour. All the speeds are in kbps. If the port speed behaviour is adaptive an error of noSuchName will be returned by the agent. | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.1 | INTEGER | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigDownFixedPortSpeed OBJECT-TYPE The value of this object corresponds to the downstream speed of the specified port for fixed port speed behaviour. All the speeds are in kbps. If the port speed behaviour is adaptive an error of noSuchName will be returned by the agent. | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.2 | INTEGER | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigUpAdaptiveUpperBoundPortSpeed OBJECT-TYPE The value of this object corresponds to the upper bound for the upstream port speed of the specified port for adaptive port speed behaviour. The speeds are measured in kbps. If the port speed behaviour is fixed an error of noSuchName will be returned by the agent. | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.3 | INTEGER | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigUpAdaptiveLowerBoundPortSpeed OBJECT-TYPE The value of this object corresponds to the lower bound for the upstream port speed of the specified port for adaptive port speed behaviour in kbps. If the port speed behaviour is fixed an error of noSuchName will be returned by the agent. The value -9999 should be used to disable the lower bound threshold check. The default value for this object is -9999 | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.4 | INTEGER | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigDownAdaptiveUpperBoundPortSpeed OBJECT-TYPE The value of this object corresponds to the upper bound allowed for the downstream port speed of the specified port for adaptive port speed behaviour. The speeds are measured in kbps. If the port speed behaviour is fixed an error of noSuchName will be returned by the agent. | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.5 | INTEGER | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigDownAdaptiveLowerBoundPortSpeed OBJECT-TYPE The value of this object corresponds to the Minimum lower bound allowed for the downstream port speed of the specified port for adaptive port speed behaviour. If the port speed behaviour is fixed an error of noSuchName will be returned by the agent. The speeds are measured in kbps. The value -9999 is used to disable the lower bound threshold check.The default value for this object is -9999 | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.6 | INTEGER | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigReedSolomonDownFwdErrCorrection OBJECT-TYPE The value of this object corresponds to the Reed-Solomon forward error correction in the downstream direction. The default value of this object should be minimizeError (1). | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.7 | INTEGER {minimizeError(1), minimizeDelay(2), reedSolomonNotSupported(3)} | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigStartUpMargin OBJECT-TYPE The value of this object corresponds to the startup value of the margin for a DSL interface (specified by ifIndex). The unit is db (decibels. The higher the margin the better the quality of the line. The default value of this object is 3. | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.8 | INTEGER (-3..9) | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigTxPowerAttenuation OBJECT-TYPE This value corresponds to the Transmitt Power Attenuation in dB for the access node. This value represents the downstream power level in dB. Permissible values are -6, -3 and 0. The default value of this object is 0 dB. The power levels +3 and +6 may be used in future. | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.9 | INTEGER | read-write | mandatory |
| xdslDevRADSLSpecificIfConfigSnTxPowerAttenuation OBJECT-TYPE This value corresponds to the Transmitt Power Attenuation in dB for the service node. This value represents the upstream power level in dB. Permissible values are -9, -6, -3 and 0. The default value of this object is -6 dB. | 1.3.6.1.4.1.1795.2.24.9.2.2.1.1.10 | INTEGER | read-write | mandatory |
| xdslDevMVLSpecificIfConfig OBJECT-IDENTITY | 1.3.6.1.4.1.1795.2.24.9.2.3 | |||
| xdslDevMVLSpecificIfConfigTable OBJECT-TYPE The xdslDevMVLSpecificIfConfigTable provides config information specific to a xDSL(MVL) device, or system. The table is indexed by an object which corresponds to ifIndex. These ifIndex entries, themselves, denote and identify specific xdsl(Mvl) interfaces on the board or module. | 1.3.6.1.4.1.1795.2.24.9.2.3.1 | not-accessible | mandatory | |
| xdslDevMVLSpecificIfConfigEntry OBJECT-TYPE Describes a specific xDSL(MVL) interface entry. | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1 | not-accessible | mandatory | |
| xdslDevMVLSpecificIfConfigMaxPortSpeed OBJECT-TYPE The value of this object corresponds to the upper bound port speed of the specified port. The speeds are measured in kbps. Prior to GrandSlam 2.3, this object was used for both upstream and downstream port speeds. Now there are 2 new objects created for downstream and upstream port speeds. Setting this value will also set the same value for the objects xdslDevMVLSpecificIfConfigMaxDownStreamPortSpeed and xdslDevMVLSpecificIfConfigMaxUpStreamPortSpeed. | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.1 | INTEGER | read-write | deprecated |
| xdslDevMVLSpecificIfConfigOnHookTxPowerAttenuation OBJECT-TYPE This value corresponds to the On-hook Transmitt Power Attenuation in dB for the access node and the service node. This value represents both downstream and upstream power level in dB while the phone is On-hook. Permissible values are -2, 1, 4, 7, 10, and +12. The default value of this object is 12 dB. | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.2 | INTEGER | read-write | mandatory |
| xdslDevMVLSpecificIfConfigOffHookTxPowerAttenuation OBJECT-TYPE This value corresponds to the Off-hook Transmitt Power Attenuation in dB for the access node and the service node. This value represents both downstream and upstream power level in dB while the phone is Off-hook. Permissible values are -11, -8, -5, -2, 1, 4, 7, 10 and +12. The default value of this object is 12 dB. | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.3 | INTEGER | read-write | mandatory |
| xdslDevMVLSpecificIfConfigOnHookPCVoltageDropThresholdValue OBJECT-TYPE This value correspond to the portcard Voltage Drop Threshold Value and valid settings are 0 and 6. If the corresponding value at the endpoint is set for Max (255) than only valid value for this object is 0. This only applies for MVL configuration If Reach configuration is used only valid value is 6 which is a default value. | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.4 | INTEGER | read-write | mandatory |
| xdslDevMVLSpecificIfConfigOnHookSNVoltageDropThresholdValue OBJECT-TYPE This corresponds to the endpoint Voltage Drop Threshold Value and valid settings are 17, 34 and 255(Max). If Reach is used than only valid value is 34 - default. | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.5 | INTEGER | read-write | mandatory |
| xdslDevMVLSpecificIfConfigMaxDownStreamPortSpeed OBJECT-TYPE The value of this object corresponds to the upper bound downstream port speed of the specified port. The speeds are measured in kbps. Setting the value of this object will also set the same value to the object xdslDevMVLSpecificIfConfigMaxPortSpeed. Prior to GrandSlam 2.3, the object xdslDevMVLSpecificIfConfigMaxPortSpeed was used for both upstream and downstream port speeds. Now there are two different objects for upstream and downstream port speeds. | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.6 | INTEGER | read-write | mandatory |
| xdslDevMVLSpecificIfConfigMaxUpStreamPortSpeed OBJECT-TYPE The value of this object corresponds to the upper bound upstream port speed of the specified port. The speeds are measured in kbps. Prior to GrandSlam 2.3, the object MaxPortSpeed was used for both upstream and downstream port speeds. Now there are two different objects for upstream and downstream port speeds. | 1.3.6.1.4.1.1795.2.24.9.2.3.1.1.7 | INTEGER | read-write | mandatory |
| xdslDevSDSLSpecificIfConfig OBJECT-IDENTITY | 1.3.6.1.4.1.1795.2.24.9.2.4 | |||
| xdslDevSDSLSpecificIfConfigTable OBJECT-TYPE The xdslDevSDSLSpecificIfConfigTable provides configuration specific to the SDSL link. | 1.3.6.1.4.1.1795.2.24.9.2.4.1 | not-accessible | mandatory | |
| xdslDevSDSLSpecificIfConfigEntry OBJECT-TYPE Describes a specific SDSL configuration entry. | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1 | not-accessible | mandatory | |
| xdslDevSDSLSpecificIfConfigFixedPortSpeed OBJECT-TYPE The value of this object corresponds to both upstream and downstream speed of the specified port. All the speeds are in kbps. The value of this object is used only when the port behaviour is fixed. | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.1 | INTEGER | read-write | mandatory |
| xdslDevSDSLSpecificIfConfigMaxPortSpeed OBJECT-TYPE The value of this object corresponds to the upper bound port speed of the specified port when the port behaviour is adaptive. The speeds are measured in kbps. | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.2 | INTEGER | read-write | mandatory |
| xdslDevSDSLSpecificIfConfigFixedPortSpeedNx128Mode OBJECT-TYPE The value of this object applies to both upstream and downstream speed of the specified port when the line rate mode is configured as Nx128 mode. All the speeds are in kbps. The value of this object is used only when the port behaviour is fixed and the line rate is Nx128 mode, and doesn't take effect in the standard mode. | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.3 | INTEGER (0..2147483647) | read-write | mandatory |
| xdslDevSDSLSpecificIfConfigMaxPortSpeedNx128Mode OBJECT-TYPE The value of this object corresponds to the upper bound port speed of the specified port when the port behaviour is adaptive and the line rate is Nx128 mode, and doesn't take effect in the standard mode. The speeds are measured in kbps. | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.4 | INTEGER (0..2147483647) | read-write | mandatory |
| xdslDevSDSLSpecificIfConfigMinSnrMargin OBJECT-TYPE Configured Minimum acceptable Signal/Noise Margin. | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.5 | INTEGER (0..15) | read-write | mandatory |
| xdslDevSDSLSpecificIfConfigTargetSnrMargin OBJECT-TYPE Configured Target Signal/Noise Margin. | 1.3.6.1.4.1.1795.2.24.9.2.4.1.1.6 | INTEGER (0..15) | read-write | mandatory |
| xdslDevIDSLSpecificIfConfig OBJECT-IDENTITY | 1.3.6.1.4.1.1795.2.24.9.2.5 | |||
| xdslDevIDSLSpecificIfConfigTable OBJECT-TYPE The xdslDevIDSLSpecificIfConfigTable provides configuration specific to the IDSL link. | 1.3.6.1.4.1.1795.2.24.9.2.5.1 | not-accessible | mandatory | |
| xdslDevIDSLSpecificIfConfigEntry OBJECT-TYPE Describes a specific IDSL configuration entry. | 1.3.6.1.4.1.1795.2.24.9.2.5.1.1 | not-accessible | mandatory | |
| xdslDevIDSLSpecificIfConfigPortSpeed OBJECT-TYPE The value of this object corresponds to both upstream and downstream speed of the specified port. All the speeds are in kbps. Allowed speeds are 64, 128 and 144 kbps. The default value for this object is 128 kbps. | 1.3.6.1.4.1.1795.2.24.9.2.5.1.1.1 | INTEGER | read-write | mandatory |
| xdslDevIDSLSpecificIfConfigTimingPortTransceiverMode OBJECT-TYPE The transceiver mode selected on the timing source port. Only one IDSL port can be set to NT mode. This timing will then be distributed to all other IDSL ports in the chassis that are set to LT. The selected xdslDevIDSLPrimaryTimingSourcePort provides clocking signals to the DSLAM when the transceiver mode is set to Network timing. The port selected for Network Timing mode will probably not used for customer data, but will receive a 2.048 Mhz Network clocking signal from a central office timing source and distribute this timing to other IDSL port cards. | 1.3.6.1.4.1.1795.2.24.9.2.5.1.1.2 | INTEGER {networkTiming(1), localTiming(2)} | read-write | mandatory |
| xdslDevIDSLSpecificChannel OBJECT-TYPE The channel type for 64 Kbps. Default value is B1. | 1.3.6.1.4.1.1795.2.24.9.2.5.1.1.3 | INTEGER {b1(1), b2(2), noOp(3)} | read-write | mandatory |
| xdslIfConfigMIBTraps OBJECT-IDENTITY | 1.3.6.1.4.1.1795.2.24.9.4 |
Notifications
| Name | OID | Status |
|---|---|---|
| xdslLinkUpDownTransitions NOTIFICATION-TYPE This trap signifies that the sending protocol entity recognizes that one of the xDSL communication links is in a fluctuating state. | 1.3.6.1.4.1.1795.2.24.9.4.0.1 |