ORiNOCO-MIB

TEXTUAL-CONVENTION

The DisplayString32 textual convention is used to define a string that can consist of 0 - 32 alphanumeric characters.

TEXTUAL-CONVENTION

The DisplayString55 textual convention is used to define a string that can consist of 0 - 55 alphanumeric characters this textual convention is used for Temperature log messages.

TEXTUAL-CONVENTION

The DisplayString80 textual convention is used to define a string that can consist of 0 - 80 alphanumeric characters.

TEXTUAL-CONVENTION

An Interface Bitmask used to enable or disable access or functionality of an interface in the system. Each bit in this object represents a network interface in the system consistent with the ifIndex object in MIB-II. The value for this object is interpreted as a bitfield, where the value of 1 means enabled. Examples of Usage: 1. For a system with the following interfaces (AP-2000 & AP-4000): - Ethernet If = 1 - Loopback If = 2 - Wireless If A = 3 - Wireless If B = 4 Interface Bitmask usage: - 00000000 (0x00): All Interfaces disabled - 00000001 (0x01): Ethernet If enabled - 00000010 (0x02): All Interfaces disabled - 00000011 (0x03): Ethernet If enabled - 00000100 (0x04): Wireless If A enabled - 00000110 (0x06): Wireless If A enabled - 00001000 (0x08): Wireless If B enabled - 00001010 (0x0A): Wireless If B enabled - 00001101 (0x0D): All Interfaces enabled - 00001111 (0x0F): All Interfaces enabled (see Note) Note: The software loopback interface bit is ignored in the usage of the interface bitmask object. 2. For a system with the following interfaces (AP-600, AP-700 & Tsunami Multipoint Devices): - Ethernet If = 1 - Loopback If = 2 - Wireless If A = 3 Interface Bitmask usage: - 00000000 (0x00): All Interfaces disabled - 00000001 (0x01): Ethernet If enabled - 00000010 (0x02): All Interfaces disabled - 00000011 (0x03): Ethernet If enabled - 00000100 (0x04): Wireless If A enabled - 00000101 (0x05): All Interfaces enabled - 00000110 (0x06): Wireless If A enabled - 00000111 (0x07): All Interfaces enabled (see Note) Note: The software loopback interface bit is ignored in the usage of the interface bitmask object. 3. For a system with the following interfaces (BG-2000): - Ethernet WAN If = 1 - Ethernet LAN If = 2 - Wireless If A = 3 Inteface Bitmask usage: - 00000000 (0x00): all Interfaces disabled - 00000001 (0x01): Ethernet WAN If enabled - 00000010 (0x02): Ethernet LAN If enabled - 00000011 (0x03): Ethernet WAN and LAN If enabled - 00000100 (0x04): Wireless If A enabled - 00000101 (0x05): Ethernet WAN and Wireless If A enabled - 00000110 (0x06): Ethernet LAN and Wireless If A enabled - 00000111 (0x07): All Interfaces enabled

TEXTUAL-CONVENTION

The status textual convention is used to enable or disable functionality or a feature.

TEXTUAL-CONVENTION

The status textual convention is used to activate, deactivate, and delete a table row.

TEXTUAL-CONVENTION

A 12-bit VLAN ID used in the VLAN Tag header.

TEXTUAL-CONVENTION

The WEPKeyType textual convention is used to define the object type used to configured WEP Keys.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table contains the inventory management objects for the system components.

OBJECT-TYPE

This object represents an entry in the system inventory management component table.

OBJECT-TYPE

This object represents the table index.

OBJECT-TYPE

This object identifies the system component serial number.

OBJECT-TYPE

This object identifies the system component name.

OBJECT-TYPE

This object identifies the system component identification.

OBJECT-TYPE

This object identifies the system component variant number.

OBJECT-TYPE

This object identifies the system component release version number.

OBJECT-TYPE

This object identifies the system component major version number.

OBJECT-TYPE

This object identifies the system component minor version number.

OBJECT-TYPE

This table contains the inventory management objects for the system components. This table has been deprecated.

OBJECT-TYPE

This object represents an entry in the system component interface table. This object has been deprecated.

OBJECT-TYPE

This object identifies the interface table index. This object has been deprecated.

OBJECT-TYPE

This object identifies the system component interface identification. This object has been deprecated.

OBJECT-TYPE

This object identifies the system component interface role. This object has been deprecated.

OBJECT-TYPE

This object identifies the system component's interface variant number. This object has been deprecated.

OBJECT-TYPE

This object identifies the system component's interface bottom number. This object has been deprecated.

OBJECT-TYPE

This object identifies the system component's interface top number. This object has been deprecated.

OBJECT-TYPE

This object is used to reboot the device. The value assigned to this object is the number of seconds until the next reboot.

OBJECT-TYPE

This object is used to identify the email address of the contact person for this managed device.

OBJECT-TYPE

This object is used to identify the phone number of the contact person for this managed device.

OBJECT-TYPE

When this variable is set, all the objects that are to be comitted to flash will be written to flash. This will be done immediately after the value is set, regardless of the value set.

OBJECT-TYPE

This object is used for the backup time interval for flash memory to be udpated.

OBJECT-TYPE

This object is used to reset the device to factory default values. When this variable is set to 1, all the objects shall be set to factory default values. The default value for this object should be 0.

OBJECT-TYPE

This object represents the mode the system is configured to operate in, either bridge or gateway/router mode.

OBJECT-TYPE

This table contains system event log information that can include events, errors, and informational messages. This is a circular buffer with a limit 100 entries.

OBJECT-TYPE

This object represents an entry in the system event log table.

OBJECT-TYPE

This object is used to store system event log information. This is also used as the index to the table.

OBJECT-TYPE

This object is used to reset/clear the event log table. When this object is the set all entries in the event log table are deleted/cleared.

OBJECT-TYPE

This object is used to control what events will be logged by the event log facility. It is a mask, each bit is used to enable/disable a corresponding set of log messages. The OR2000 uses the standard syslog priorities and facilities. The Mask should only be set to mask specific facilities. The facilities are: LOG_KERN (0<<3) kernel messages LOG_USER (1<<3) random user-level messages LOG_MAIL (2<<3) mail system LOG_DAEMON (3<<3) system daemons LOG_AUTH (4<<3) authorization messages LOG_SYSLOG (5<<3) messages generated internally by syslogd LOG_LPR (6<<3) line printer subsystem LOG_NEWS (7<<3) network news subsystem LOG_UUCP (8<<3) UUCP subsystem LOG_CRON (9<<3) clock daemon LOG_AUTHPRIV (10<<3) authorization messages (private) LOG_FTP (11<<3) ftp daemon LOG_NTP (12<<3) NTP subsystem LOG_SECURITY (13<<3) security subsystems (firewalling, etc.) LOG_CONSOLE (14<<3) /dev/console output - other codes through 15 reserved for system use LOG_LOCAL0 (16<<3) reserved for local use LOG_LOCAL1 (17<<3) reserved for local use LOG_LOCAL2 (18<<3) reserved for local use LOG_LOCAL3 (19<<3) reserved for local use LOG_LOCAL4 (20<<3) reserved for local use LOG_LOCAL5 (21<<3) reserved for local use LOG_LOCAL6 (22<<3) reserved for local use LOG_LOCAL7 (23<<3) reserved for local use On the BG2000: Each nibble (4 bits == 1 hex digit == a nibble) represents a category of log messages. There are 4 levels of messages per category (1 bit per level per category). The least significant bit is a higher priority message. As follows: security - nibble 1, bits 1-4 errors - nibble 2, bits 5-8 system startup - nibble 3, bits 9-12 warnings - nibble 4, bits 13-16 information - nibble 5, bits 17-20 0x00000 - No events will be logged. 0x000F0 - Only errors will be logged. 0x0F0F0 - Warnings and errors will be logged. 0xFFFFF - All events will be logged.

OBJECT-TYPE

This object represents the system access user name for the supported management interfaces (Telnet and HTTP).

OBJECT-TYPE

This object represents the system access password for the supported management interfaces (Telnet and HTTP). This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents the login timeout in seconds. The default value should be 60 seconds (1 minute).

OBJECT-TYPE

This object represents the inactivity or idle timeout in seconds. The default value should be 900 seconds (15 minutes).

OBJECT-TYPE

This object represents the number of messages currently stored in the event log table.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains a list of features that the current image supports and indicates if this features is licensed (enabled) or not (disabled). Each row represents a supported and/or licensed feature. Supported indicates if the current image supports the image while Licensed indicates that a license is available to use this feature. Based on the license information in this table, some MIB groups/subgroups/tables will be enabled or disabled.

OBJECT-TYPE

This object represents an entry in the system feature license table.

OBJECT-TYPE

This object identifies the code for the licensed feature and is used as index for this table.

OBJECT-TYPE

This object represents the maximum value for the feature as supported by the current image. For boolean features zero means not supported, non-zero value means supported.

OBJECT-TYPE

This object represents the maximum value for the feature as enforced by the license(s). For boolean features zero means not licensed, non-zero value means licensed.

OBJECT-TYPE

This object represents a textual description for the licensed feature.

OBJECT-TYPE

This object controls the maximum number of simultaneous telnet, http, and serial managmenent sessions.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the syslog feature.

OBJECT-TYPE

This object represents the UDP destination port number for syslog services. The standard syslog port is 514.

OBJECT-TYPE

This object represents the lowest message priority to be logged by the syslog service.

OBJECT-TYPE

This object is used to enable or disable logging of heartbeat messages by the syslog service.

OBJECT-TYPE

This object is used to configure interval (in seconds) for which heartbeat messages will be logged.

OBJECT-TYPE

This table is used to configure syslog hosts.

OBJECT-TYPE

This object represents an entry for the syslog host table.

OBJECT-TYPE

This object represents an index in the syslog host table.

OBJECT-TYPE

This object represents the IP address of the host running the syslog daemon.

OBJECT-TYPE

This object represents an optional comment for the syslog host, for example the host name or a reference.

OBJECT-TYPE

This object is used to enable, disable, delete, or create an entry in the syslog host table.

OBJECT-TYPE

This attribute identifies the country in which the station is operating. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. Below is the list of mapping of country codes to country names. AL - ALBANIA DZ - ALGERIA AR - ARGENTINA AM - ARMENIA AU - AUSTRALIA AT - AUSTRIA AZ - AZERBAIJAN BH - BAHRAIN BY - BELARUS BE - BELGIUM BZ - BELIZE BO - BOLIVIA BR - BRAZIL BN - BRUNEI DARUSSALAM BG - BULGARIA CA - CANADA CL - CHILE CN - CHINA CO - COLOMBIA CR - COSTA RICA HR - CROATIA CY - CYPRUS CZ - CZECH REPUBLIC DK - DENMARK DO - DOMINICAN REPUBLIC EC - ECUADOR EG - EGYPT EE - ESTONIA FI - FINLAND FR - FRANCE GE - GEORGIA DE - GERMANY GR - GREECE GT - GUATEMALA HK - HONG KONG HU - HUNGARY IS - ICELAND IN - INDIA ID - INDONESIA IR - IRAN IE - IRELAND I1 - IRELAND - 5.8GHz IL - ISRAEL IT - ITALY JP - JAPAN J2 - JAPAN2 JO - JORDAN KZ - KAZAKHSTAN KP - NORTH KOREA KR - KOREA REPUBLIC K2 - KOREA REPUBLIC2 KW - KUWAIT LV - LATVIA LB - LEBANON LI - LIECHTENSTEIN LT - LITHUANIA LU - LUXEMBOURG MO - MACAU MK - MACEDONIA MY - MALAYSIA MX - MEXICO MC - MONACO MA - MOROCCO NL - NETHERLANDS NZ - NEW ZEALAND NO - NORWAY OM - OMAN PK - PAKISTAN PA - PANAMA PE - PERU PH - PHILIPPINES PL - POLAND PT - PORTUGAL PR - PUERTO RICO QA - QATAR RO - ROMANIA RU - RUSSIA SA - SAUDI ARABIA SG - SINGAPORE SK - SLOVAK REPUBLIC SI - SLOVENIA ZA - SOUTH AFRICA ES - SPAIN SE - SWEDEN CH - SWITZERLAND SY - SYRIA TW - TAIWAN TH - THAILAND TR - TURKEY UA - UKRAINE AE - UNITED ARAB EMIRATES GB - UNITED KINGDOM G1 - UNITED KINGDOM - 5.8GHz US - UNITED STATES UW - UNITED STATES - World U1 - UNITED STATES - DFS UY - URUGUAY VE - VENEZUELA VN - VIETNAM

OBJECT-IDENTITY

OBJECT-TYPE

This object is used for the internal unit temperature in degrees celsius. The range of the temperature is -30 to 60 degrees celsius.

OBJECT-TYPE

This object is used for logging interval. The valid values are 1,5,10,15,20,25,30,35,40,45,50,55,and 60.

OBJECT-TYPE

This table contains temperature log information. This is a circular buffer with a limit 576 entries.

OBJECT-TYPE

This object represents an entry in the temperature log table.

OBJECT-TYPE

This object is used to store temperature log information. This is also used as the index to the table.

OBJECT-TYPE

This object is used for resetting the temperature log table.

OBJECT-TYPE

This attribute identifies the type of TMP11 hardware i.e. Indoor or Outdoor.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table contains information on the properties and capabilities of the wireless interface(s) present in the device.

OBJECT-TYPE

This object represents the entry in the wireless interface properties table.

OBJECT-TYPE

This object represents a unique value for each interface in the system and is used as index to this table.

OBJECT-TYPE

This object represents the network name (SSID) for this wireless interface.

OBJECT-TYPE

This object represents the medium reservation value. The range for this parameter is 0 - 2347. The medium reservation specifies the number of octects in a frame above which a RTS/CTS handshake is performed. The default value should be 2347, which disables RTS/CTS mode.

OBJECT-TYPE

This object enables or disables the interference robustness feature. The default value for this object should be disable.

OBJECT-TYPE

This object represents the delivery traffic indication map period. This is the interval between the transmission of multicast frames on the wireless inteface. It is expressed in the Beacon messages. The recommended default value for this object is 1.

OBJECT-TYPE

This object represents the radio frequency channel for this wireless interface. The default value for the channel is based on the regulatory domain.

OBJECT-TYPE

This object identifies the distance between access points. The default value for this parameter should be large.

OBJECT-TYPE

This object is used to configure the multicast rate, but it is dependent on the type of wireless NIC. The value of this object is given in 500 Kbps units. This object can be configured to one of the values defined by the supported multicast rates objects (oriWirelessIfSupportedMulticastRates). For 802.11b Wireless NICs: This object identifies multicast rate of the wireless interface. This is dependent on the distance between APs. When the distance between APs object is set to small, minicell, or microcell the multicast rates can be set to 11 Mbit/s (22 in 500 Kbps units), 5.5 Mbit/s (11), 2 Mbit/s (4), and 1 Mbit/s (2). When this object is set to medium, the allowed rates are 5.5 Mbit/s (11), 2 Mbit/s (4), 1 Mbit/s (2). When this object is set to large, then the multicast rates can be set to 2 Mbits/s (4) or 1 Mbits/s (2). The default value for this object should be 2 Mbits/sec (4). For 802.11a, g, and a/g Wireless NICs: This object is used to set the multicast rate for beacons, frames used for protection mechanism (CTS), and other multicast and broadcast frames.

OBJECT-TYPE

This object is used as a flag which identifies whether the device will accept association requests to this interface, for client stations configured with a network name of 'ANY'. When this object is disabled, it will accept association requests from client stations with a network name of 'ANY'. If this object is set to enable then the interface will only accept association requests that match the interface's network name (SSID). The default value for this object should be disable.

OBJECT-TYPE

This object reflects the transmit rates supported by the wireless interface. The values of this object are given in units of 500 kbps. Examples for supported data rates: - 802.11b PHY (DSSS - 2.4 GHz) - 0 = Auto Fallback - 2 = 1 Mbps - 4 = 2 Mbps - 11 = 5.5 Mbps - 22 = 11 Mbps - 802.11a PHY (OFDM - 5 GHz) - 0 = Auto Fallback - 12 = 6 Mbps - 18 = 9 Mbps - 24 = 12 Mbps - 36 = 18 Mbps - 48 = 24 Mbps - 72 = 36 Mbps - 96 = 48 Mbps - 108 = 54 Mbps - 802.11a PHY (OFDM - 5 GHz) with Turbo Mode Enabled - 0 = Auto Fallback - 24 = 12 Mbps - 36 = 18 Mbps - 48 = 24 Mbps - 72 = 36 Mbps - 96 = 48 Mbps - 144 = 72 Mbps - 192 = 96 Mbps - 216 = 108 Mbps - 802.11g PHY (ERP) in 802.11g only mode - 0 = Auto Fallback - 12 = 6 Mbps - 18 = 9 Mbps - 24 = 12 Mbps - 36 = 18 Mbps - 48 = 24 Mbps - 72 = 36 Mbps - 96 = 48 Mbps - 108 = 54 Mbps - 802.11g PHY (ERP) in 802.11b/g mode - 0 = Auto Fallback - 2 = 1 Mbps - 4 = 2 Mbps - 11 = 5.5 Mbps - 12 = 6 Mbps - 18 = 9 Mbps - 22 = 11 Mbps - 24 = 12 Mbps - 36 = 18 Mbps - 48 = 24 Mbps - 72 = 36 Mbps - 96 = 48 Mbps - 108 = 54 Mbps

OBJECT-TYPE

This object specifies a single regulatory domain (not a list) which is supported by the wireless interface.

OBJECT-TYPE

This object reflects the radio frequency channels that the interface supports.

OBJECT-TYPE

This object represents the MAC address of the wireless interface present in the device. This object has been deprecated.

OBJECT-TYPE

This object is used to configure the load balancing feature for the wireless interface.

OBJECT-TYPE

This object is used to configure the medium density distribution feature for the wireless interface.

OBJECT-TYPE

This object is used to configure the transmit rate for unicast traffic for the wireless interface. This object is dependent on the transmit rates supported by the wireless interface (refer to MIB object - oriWirelessIfAllowedSupportedDataRates and dot11PHYType). The values of this object are given in units of 500 kbps. A value of zero (0) is interpreted as auto fallback. Examples for configuring this object: - 802.11b PHY (DSSS - 2.4 GHz) - 0 = Auto Fallback - 2 = 1 Mbps - 4 = 2 Mbps - 11 = 5.5 Mbps - 22 = 11 Mbps - 802.11a PHY (OFDM - 5 GHz) - 0 = Auto Fallback - 12 = 6 Mbps - 18 = 9 Mbps - 24 = 12 Mbps - 36 = 18 Mbps - 48 = 24 Mbps - 72 = 36 Mbps - 96 = 48 Mbps - 108 = 54 Mbps - 802.11a PHY (OFDM - 5 GHz) with Turbo Mode Enabled - 0 = Auto Fallback - 24 = 12 Mbps - 36 = 18 Mbps - 48 = 24 Mbps - 72 = 36 Mbps - 96 = 48 Mbps - 144 = 72 Mbps - 192 = 96 Mbps - 216 = 108 Mbps - 802.11g PHY (ERP) in 802.11g only mode - 0 = Auto Fallback - 12 = 6 Mbps - 18 = 9 Mbps - 24 = 12 Mbps - 36 = 18 Mbps - 48 = 24 Mbps - 72 = 36 Mbps - 96 = 48 Mbps - 108 = 54 Mbps - 802.11g PHY (ERP) in 802.11b/g mode - 0 = Auto Fallback - 2 = 1 Mbps - 4 = 2 Mbps - 11 = 5.5 Mbps - 12 = 6 Mbps - 18 = 9 Mbps - 22 = 11 Mbps - 24 = 12 Mbps - 36 = 18 Mbps - 48 = 24 Mbps - 72 = 36 Mbps - 96 = 48 Mbps - 108 = 54 Mbps The default value for this object should be zero (0) auto fallback.

OBJECT-TYPE

This object is used to configure the automatic frequency channel feature for the wireless interface. If this object is enabled, the frequency channel object can not be set, but the frequency channel selected will be given in that object. The default value for this object should be enable.

OBJECT-TYPE

This object represents the input bandwidth limit of the interface in increments of 64 kbps. The value can be limited by a previous written value, the negotiation process during registration or by a license. A written value will only take effect after reboot.

OBJECT-TYPE

This object represents the output bandwidth limit of the interface in increments of 64 kbps. The value can be limited by a previous written value, the negotiation process during registration or by a license. A written value will only take effect after reboot.

OBJECT-TYPE

This object is used to enable or disable turbo mode support. Turbo mode is only supported for 802.11a PHY (OFDM - 5 GHz) and 802.11g (ERP - 2.4 GHz) wireless NICs and can only be enabled when super mode is enabled. When Turbo mode is enabled the data rates will be doubled (refer to oriWirelessIfAllowedSupportedDataRates object description).

OBJECT-TYPE

This object provides information on the wireless operational modes supported by the NIC. Depending on the wireless NIC in the device different wireless operational modes can be configured. The possible supported modes can be: - 802.11b only - 802.11g only - 802.11b/g - 802.11a only - 802.11g-wifi

OBJECT-TYPE

This object is used to set the wireless NIC Operational mode. Depending on the wireless NIC in the device different wireless operational modes can be configured. The supported modes are: - 802.11b only - 802.11g only - 802.11b/g - 802.11a only - 802.11g-wifi

OBJECT-TYPE

This object identifies the wireless interface preamble type based on the wireless operational mode configured.

OBJECT-TYPE

This object indicates if protection mechanism is enabled or not based on the wireless operational mode configured.

OBJECT-TYPE

This object represents the multicast rates supported by the wireless NIC and the operational mode configured.

OBJECT-TYPE

This object provides information on the wireless capabilities and features supported by the wireless NIC. Each bit in this object defines a capability/feature supported by the wireless NIC. If the bit is set, the capability/feature is supported, otherwise it is not. The following list provides a definition of the bits in this object: b0 - Distance Between APs b1 - Multicast Rate b2 - Closed System b3 - Load Balancing b4 - Medium Density Distribution b5 - Auto Channel Select b6 - Turbo Mode b7 - Interference Robustness b8 - Wireless Distribution System (WDS) b9 - Transmit Power Control (TPC) b10 - Multiple SSIDs b11 - SpectraLink VoIP b12 - Remote Link Test b13 to b255 - Reserved

OBJECT-TYPE

Maximum allowed Tx processing time, in mS, where Tx processing time is measured from time a packet enters AP from the DS to the time it successfully leaves the AP's Radio.

OBJECT-TYPE

Maximum allowed difference in mS between adjacent AP's Tx processing time.

OBJECT-TYPE

This object is used to configure the frequency bands that the auto channel select algorithm will scan through. Each bit in this object represents a band or subset of channels in the 5 GHz or 2.4 GHz space. The value of this object is interpreted as a bitfield, where the value of 1 means enable ACS scan for that band. The following list provides a definition of the bits in this object: b0 - U-NII Lower Band = 5.15 - 5.25 GHz (36, 40, 44, 48) b1 - U-NII Middle Band = 5.25 - 5.35 GHz (52, 56, 60, 64) b2 - U-NII Upper Band = 5.725 - 5.825 GHz (149, 153, 157, 161) b3 - H Band = 5.50 - 5.700 GHz (100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140) b4 - 5 GHz ISM Band = 5.825 GHz (165) b5 to b255 - Reserved

OBJECT-TYPE

This object is used to enable or disable the security per SSID feature. Once this object is enabled, the administrator should use the Wireless Interface SSID table (oriWirelessIfSSIDTable to configure the security related management objects.

OBJECT-TYPE

This object is used to enable/disable dynamic frequency selection. This functionality is dependent on the regulatory domain of the wireless NIC.

OBJECT-TYPE

This object is used to configure the antenna. The administrator can select controllable, external, internal, or disable the antenna.

OBJECT-TYPE

This object is used to configure the transmit power control of the wireless NIC. The transmit power is defined in dBm and can be configured in increments 3 dBms.

OBJECT-TYPE

This object is used to enable/disable super mode support. Super Mode increases the overall throughput of the wireless interface by implementing fast frame, bursting, and compression. When super mode is enabled, the channels that can be used in the 2.4 GHz and 5.0 GHz spectrum are limited (refer to oriWirelessIfAllowedChannels for the allowed channels). The super mode feature is only supported for 802.11a (OFDM - 5 GHz) and 802.11g (ERP - 2.4 GHz) wireless NICs.

OBJECT-TYPE

This object is used for the Wireless System Shutdown feature. This feature allows an administrator to shut down wireless services to clients. When this object is set to down wireless client services will be shutdown/disabled, but WDS links will still remain up.

OBJECT-TYPE

This object is used to provide information on the authentication modes supported by the wireless interface. The possible authentication modes are: - none: no authentication mode - dot1x: 802.1x authentication mode - psk: psk authentication mode

OBJECT-TYPE

This object is used to provide information on the cipher modes/types supported by the wireless interface. The possible cipher modes/types are: - none: no cipher/encryption mode - wep: wep encryption mode - tkip: tkip encryption mode - aes: aes encryption mode

OBJECT-TYPE

This object is used to enable/disable Quality of Service (QoS) on the wireless interface.

OBJECT-TYPE

This object is used to specify the QoS admission control maximum medium threshold. The maximum medium threshold will apply to all access categories and is given in a percentage of the medium.

OBJECT-TYPE

This object represents Antenna Gain value (including cable loss) that will be added to the radar detetection parameters.

OBJECT-TYPE

This table contains information on the security management objects for the wireless interface(s) present in the device.

OBJECT-TYPE

This object represents an entry in the wireless interface security table.

OBJECT-TYPE

This object represents a unique value for each interface in the system and is used as index to this table.

OBJECT-TYPE

This object sets the wireless interface's security capabilities (such as WEP and other standard and proprietary security features). AES encryption is only for 802.11a and supports only OCB mode integrity check.

OBJECT-TYPE

This object is used to enable or disable WEP encryption for the wireless interface.

OBJECT-TYPE

This object represents Encryption Key 1. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents Encryption Key 2. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents Encryption Key 3. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents Encryption Key 4. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object indicates which encryption key is used to encrypt data that is sent via the wireless interfaces. When this object is configured to 0, then Encryption Key 1 will be used. When this object is configured to 1, then Encryption Key 2 will be used. When this object is configured to 2, then Encryption Key 3 will be used. When this object is configured to 3, then Encryption Key 4 will be used. The default value for this object should be key 0.

OBJECT-TYPE

This parameter indicates if this interface will accept or deny non-encrypted data. The default value for this parameters is disabled.

OBJECT-TYPE

The object represents the profile code of the wirelesss interface. This information is comprised of a vendor indication and a capability indication (example: bronze or gold card).

OBJECT-TYPE

This table is used to configure the SSIDs for the wireless interface in the device.

OBJECT-TYPE

This object represents an entry in the respective table. In this case each table entry represents a VLAN ID.

OBJECT-TYPE

This object represents the index to the SSID Table.

OBJECT-TYPE

This object represents the wireless card SSID string (wireless network name).

OBJECT-TYPE

This object represents the VLAN Identifier (ID).

OBJECT-TYPE

This object represents the wireless SSID table row/entry status.

OBJECT-TYPE

This object is used to configure the security mode for this table entry (SSID). This object is deprecated.

OBJECT-TYPE

This object is used to enable/disable a broadcast SSID in the SSID table. A single entry in the SSID table can be enabled to broadcast SSID in beacon messages.

OBJECT-TYPE

This object is used to enable/disable the closed system feature for this table entry (SSID).

OBJECT-TYPE

This object is used to provide information on the supported security modes by the wireless interface(s). The possible security modes can be: - None: no security mode enabled. - dot1x: 802.1x authentication enabled. - mixed: mixed WEP and 802.1x. - wpa: WiFi Protected Access enabled. - wpa-psk: WiFi Protected Access with Preshared Keys enabled. - wep: WEP Encryption enabled (no authentication) This object is deprecated.

OBJECT-TYPE

This object represents Encryption Key 0. This object should be treated as write-only and returned as asterisks. This object is deprecated.

OBJECT-TYPE

This object represents Encryption Key 1. This object should be treated as write-only and returned as asterisks. This object is deprecated.

OBJECT-TYPE

This object represents Encryption Key 2. This object should be treated as write-only and returned as asterisks. This object is deprecated.

OBJECT-TYPE

This object represents Encryption Key 3. This object should be treated as write-only and returned as asterisks. This object is deprecated.

OBJECT-TYPE

This object indicates which encryption key is used to encrypt data that is sent via the wireless interfaces. The default value for this object should be key 0. This object is deprecated.

OBJECT-TYPE

This object represents the encryption key length, the supported key lengths are 64 bits (40 + 24 for IV), 128 bits (104 + 24 for IV), and 152 bits (128 + 24 for IV). This object is deprecated.

OBJECT-TYPE

This object represents the encryption rekeying interval. if this object is configured to zero (0) rekeying is disabled. The units of this object is seconds.

OBJECT-TYPE

The Pre-Shared Key (PSK) for when RSN in PSK mode is the selected authentication suite. In that case, the PMK will obtain its value from this object. This object is logically write-only. Reading this variable shall return unsuccessful status or null or zero. This object is deprecated.

OBJECT-TYPE

The PSK, for when RSN in PSK mode is the selected authentication suite, is configured by oriWirelessIfSSIDTablePSKValue. An alternative manner of setting the PSK uses the password-to-key algorithm defined in the standard. This variable provides a means to enter a pass phrase. When this object is written, the RSN entity shall use the password-to-key algorithm specified in the standard to derive a pre-shared and populate oriWirelessIfSSIDTablePSKValue with this key. This object is logically write-only. Reading this variable shall return unsuccessful status or null or zero. This object is deprecated.

OBJECT-TYPE

This object is used to enable/disable deny non encrypted data. This function is only supported when the security mode is configured to WEP or Mixed Mode; it is not supported for 802.1x, WPA, and WPA-PSK security modes. This object is deprecated.

OBJECT-TYPE

This object is used to enable or disable SSID Authorization.

OBJECT-TYPE

This object is used to enable or disable MAC Access Control feature/filter for this SSID.

OBJECT-TYPE

This object is used to enables RADIUS Access Control based on wireless stations MAC Address.

OBJECT-TYPE

This object is used to configure the security profile that will be used for this SSID. The security profile is defined in the Security Profile Table in the orinocoSecurity group.

OBJECT-TYPE

This object is used to configure the RADIUS server profile that will be used for 802.1x authentication for this SSID. The RADIUS profile is defined in the RADIUS Server Table in the orinocoRADIUSSvrProfile group.

OBJECT-TYPE

This object is used to configure the RADIUS server profile that will be used for MAC based RADIUS authentication for this SSID. The RADIUS profile is defined in the RADIUS Server Table in the orinocoRADIUSSvrProfile group.

OBJECT-TYPE

This object is used to enable or disable the RADIUS Accounting service per SSID.

OBJECT-TYPE

This object is used to configure the RADIUS server profile that will be used for Accounting for this SSID. The RADIUS profile is defined in the RADIUS Server Table in the orinocoRADIUSSvrProfile group.

OBJECT-TYPE

This object is used to configure the QoS policy that will be used for this SSID. The QoS profile is defined in the QoS Policy Table in the orinocoQoS group.

OBJECT-TYPE

This object is used to enable or disable Transmit (Tx) Power Control feature.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure the ethernet interface(s) for the device.

OBJECT-TYPE

This object represents an entry in the ethernet interface configuration table.

OBJECT-TYPE

This object represents the index of the ethernet configuraiton table.

OBJECT-TYPE

This object is used to configure the Ethernet interface's speed. Some devices support all the configuration options listed above, while others support only a subset of the configuration options.

OBJECT-TYPE

This object represents the input bandwidth limit of the interface in increments of 64 kbps. The value can be limited by a previous written value, the negotiation process during registration, or by a license. A written value will only take effect after reboot.

OBJECT-TYPE

This object represents the output bandwidth limit of the interface in increments of 64 kbps. The value can be limited by a previous written value, the negotiation process during registration, or by a license. A written value will only take effect after reboot.

OBJECT-TYPE

This object represents the MAC address of the WAN interface.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure the mode, time-outs, and protocol objects for wireless interface(s) that are configured to run WORP.

OBJECT-TYPE

This object represents an entry in the WORP Interface Configuration Table.

OBJECT-TYPE

The running mode of this interface: - If set to disabled, the interface is disabled. - If set to AP, the interface will run in standard IEEE802.11 mode. - If set to Base, the interface will be a WORP master interface and be able to connect to multiple WORP satellites. - If set to Satellite, the interface will be a WORP slave interface.

OBJECT-TYPE

The name of the base station. For a base this name will default to the MIB-II sysName; for a satellite to empty (if not registered to any base) or the name it is registered to. When a name is set for a satellite, the satellite will only register on a base with this name.

OBJECT-TYPE

The maximum of remotes allowed on this interface. Please note that this value will also be limited by the image and the license.

OBJECT-TYPE

This object represents the Timeout of regristration and authentication, configurable between 1sec and 10sec.

OBJECT-TYPE

The number of times a data message will be retransmitted, configurable between 0 and 10. The value 0 allows unreliable operation for streaming applications.

OBJECT-TYPE

The NetworkSecret is a string that must be the same for all stations in a certain network. If a station has another secret configured as the base, the base will not allow the station to register. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object is used to enable or disable sleep mode. If this object is enabled, a subscriber unit will not go into sleep mode when they have no data to send.

OBJECT-TYPE

This table is used to monitor the statistics of interfaces that run WORP.

OBJECT-TYPE

This object represents an entry in the WORP Interface Statistics Table.

OBJECT-TYPE

The number of remote partners. For a satellite, this parameter will always be zero or one.

OBJECT-TYPE

The current signal level calculated over all inbound packets. This variable indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current noise level calculated over all inbound packets. This variable indicates the running average of the local noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current remote signal level calculated over the inbound packets send by this station. This variable indicates the running average over all registered stations of the remote signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current average remote noise level calculated over the inbound packets send by this station. This variable indicates the running average over all registered stations of the remote noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The number of Base Station Announces Broadcasts (BSAB) sent (base) or received (satellite) on this interface.

OBJECT-TYPE

The number of Registration Requests (RREQ) sent (satellite) or received (base) on this interface.

OBJECT-TYPE

The number of Registration Rejects (RREJ) sent (base) or received (satellite) on this interface.

OBJECT-TYPE

The number of Authentication Requests (AREQ) sent (satellite) or received (base) on this interface.

OBJECT-TYPE

The number of Authentication Confirms (ACFM) sent (base) or received (satellite) on this interface.

OBJECT-TYPE

The number of times a Registration Attempt has been initiated.

OBJECT-TYPE

The number of registration attempts that is not completed yet. For a satellite this parameters will always be zero or one.

OBJECT-TYPE

The number of times the registration procedure timed out.

OBJECT-TYPE

The reason for why the last registration was aborted or failed.

OBJECT-TYPE

The number of polls with data sent (base) or received (satellite).

OBJECT-TYPE

The number of polls with no data sent (base) or received (satellite).

OBJECT-TYPE

The number of poll replies with data sent (satellite) or received (base). This counter does not include replies with the MoreData flag set (see ReplyMoreData).

OBJECT-TYPE

The number of poll replies with data sent (satellite) or received (base) with the MoreData flag set (see also ReplyData).

OBJECT-TYPE

The number of poll replies with no data sent (satellite) or received (base).

OBJECT-TYPE

The number of requests for service sent (satellite) or received (base).

OBJECT-TYPE

The number of data packets sent that were acknowledged and did not need a retransmit.

OBJECT-TYPE

The number of data packets sent that needed retransmition but were finally received succesfully by the remote partner.

OBJECT-TYPE

The number of data packets sent that were (finally) not received succesfully by the remote partner.

OBJECT-TYPE

The number of data packets received that were acknowledged and did not need a retransmit of the remote partner.

OBJECT-TYPE

The number of data packets received that needed retransmition by the remote partner but were finally received succesfully.

OBJECT-TYPE

The number of data packets that were (finally) not received succesfully.

OBJECT-TYPE

The number of times a poll was sent but no reply was received. This object only applies to the base.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the per-satellite config from the base device.

OBJECT-TYPE

This table contains wireless stations statistics.

OBJECT-TYPE

This object represents an entry in the WORP Interface Satellite Statistics Table.

OBJECT-TYPE

This object is used to index the protocol filter table.

OBJECT-TYPE

This object is used to enable, disable, delete, create the Ethernet protocols in this table.

OBJECT-TYPE

This object represents the MAC address of the satellite for which the statistics are gathered.

OBJECT-TYPE

This object represents the minimum input bandwidth limit of the interface in increments of 64 kbps. The value can be limited by a previous written value, the negotiation process during registration or by a license. A written value will only take effect after reboot.

OBJECT-TYPE

This object represents the maximum input bandwidth limit of the interface in increments of 64 kbps. The value can be limited by a previous written value, the negotiation process during registration or by a license. A written value will only take effect after reboot.

OBJECT-TYPE

This object represents the minimum output bandwidth limit of the interface in increments of 64 kbps. The value can be limited by a previous written value, the negotiation process during registration or by a license. A written value will only take effect after reboot.

OBJECT-TYPE

This object represents the maximum output bandwidth limit of the interface in increments of 64 kbps. The value can be limited by a previous written value, the negotiation process during registration or by a license. A written value will only take effect after reboot.

OBJECT-TYPE

This object is used for an optional comment associated to the per Satellite config Table entry.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains wireless stations statistics.

OBJECT-TYPE

This object represents an entry in the WORP Interface Satellite Statistics Table.

OBJECT-TYPE

This object represents the table index for SatStat Table.

OBJECT-TYPE

This object represents the MAC address of the satellite for which the statistics are gathered.

OBJECT-TYPE

The current signal level calculated over all inbound packets. This variable indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current noise level calculated over all inbound packets. This variable indicates the running average of the local noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current remote signal level calculated over the inbound packets send by this station. This variable indicates the running average over all registered stations of the remote signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current average remote noise level calculated over the inbound packets send by this station. This variable indicates the running average over all registered stations of the remote noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The number of polls with data sent (base) or received (satellite).

OBJECT-TYPE

The number of polls with no data sent (base) or received (satellite).

OBJECT-TYPE

The number of poll replies with data sent (satellite) or received (base). This counter does not include replies with the MoreData flag set (see ReplyMoreData).

OBJECT-TYPE

The number of poll replies with no data sent (satellite) or received (base).

OBJECT-TYPE

The number of requests for service sent (satellite) or received (base).

OBJECT-TYPE

The number of data packets sent that were acknowledged and did not need a retransmit.

OBJECT-TYPE

The number of data packets sent that needed retransmition but were finally received succesfully by the remote partner.

OBJECT-TYPE

The number of data packets sent that were (finally) not received succesfully by the remote partner.

OBJECT-TYPE

The number of data packets received that were acknowledged and did not need a retransmit of the remote partner.

OBJECT-TYPE

The number of data packets received that needed retransmition by the remote partner but were finally received succesfully.

OBJECT-TYPE

The number of data packets that were (finally) not received succesfully.

OBJECT-TYPE

The number of times a poll was sent but no reply was received. This object only applies to the base.

OBJECT-TYPE

This object represents the Transmit Data Rate of the BSU.

OBJECT-TYPE

This object represents the Transmit Data Rate of the SU which is registered to this SU.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the site survey mode. The site survey is going to show user the wireless signal level, noise level and SNR value.

OBJECT-TYPE

This table contains the information for the stations currently associated with the access point.

OBJECT-TYPE

This object represents the entry in the Remote Link Test table.

OBJECT-TYPE

This object represents a unique entry in the table.

OBJECT-TYPE

This object represents the MAC address of the base unit being tested with.

OBJECT-TYPE

This object identifies the name of the base unit being tested with..

OBJECT-TYPE

This object identifies the maximum number of satellites is allowed to be registered with the base unit being tested with.

OBJECT-TYPE

This object identifies the maximum number of satellites is allowed to be registered with the base unit being tested with.

OBJECT-TYPE

This object identifies the maximum number of satellites is allowed to be registered with the base unit being tested with.

OBJECT-TYPE

The current signal level (in dB) for the Site Survey from this station. This object indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current noise level (in dB) for the Site Survey to this station. This object indicates the running average of the local noise level.

OBJECT-TYPE

The current signal to noise ratio for the Site Survey to this station.

OBJECT-TYPE

The current signal level (in dB) for the Site Survey from the base with which the current satellite is registered. This object indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current noise level (in dB) for the Site Survey from the base with which the current satellite is registered.

OBJECT-TYPE

The current SNR (in dB) for the Site Survey from the base with which the current satellite is registered.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable/disable Roaming between BSUs.

OBJECT-TYPE

This object specifies the threshold for initiating slow scanning procedure. The units of this object is dBs.

OBJECT-TYPE

This object specifies the threshold for initiating fast scanning procedure. The units of this object is dBs.

OBJECT-TYPE

This object specifies the threshold for roaming threshold. The units of this object is dBs.

OBJECT-TYPE

This object specifies the threshold percentage of retransmissions for initiating slow scanning procedure.

OBJECT-TYPE

This object specifies the threshold percentage of retransmissions for initiating fast scanning procedure.

OBJECT-IDENTITY

OBJECT-TYPE

This is object is used to enable/disable the WORP DDRS feature on the BSU.

OBJECT-TYPE

This is the data rate that shall be used only when DDRS is enabled. This is to specify default data rate on BSU. The possible values of the variable shall be: 1. 802.11a normal mode 6Mbps 2. 802.11a normal mode 9Mbps 3. 802.11a normal mode 12Mbps 4. 802.11a normal mode 18Mbps 5. 802.11a normal mode 24Mbps 6. 802.11a normal mode 36Mbps 7. 802.11a normal mode 48Mbps 8. 802.11a normal mode 54Mbps 9. 802.11a turbo mode 12Mbps 10. 802.11a turbo mode 18Mbps 11. 802.11a turbo mode 24Mbps 12. 802.11a turbo mode 36Mbps 13. 802.11a turbo mode 48Mbps 14. 802.11a turbo mode 72Mbps 15. 802.11a turbo mode 96Mbps 16. 802.11a turbo mode 108Mbps

OBJECT-TYPE

This is the data rate that shall be used only when DDRS is enabled. This is to limit maximum possible data rate that is set by DDRS on BSU. The possible values of the variable shall be: 1. 802.11a normal mode 6Mbps 2. 802.11a normal mode 9Mbps 3. 802.11a normal mode 12Mbps 4. 802.11a normal mode 18Mbps 5. 802.11a normal mode 24Mbps 6. 802.11a normal mode 36Mbps 7. 802.11a normal mode 48Mbps 8. 802.11a normal mode 54Mbps 9. 802.11a turbo mode 12Mbps 10. 802.11a turbo mode 18Mbps 11. 802.11a turbo mode 24Mbps 12. 802.11a turbo mode 36Mbps 13. 802.11a turbo mode 48Mbps 14. 802.11a turbo mode 72Mbps 15. 802.11a turbo mode 96Mbps 16. 802.11a turbo mode 108Mbps

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 6Mbps on 802.11a radio, normal mode. The value should be in dB and in the range 0..50 dB. The default value should be 6dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 9Mbps on 802.11a radio, normal mode. The value should be in dB and in the range 0..50 dB. The default value should be 7dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 12Mbps on 802.11a radio, normal mode. The value should be in dB and in the range 0..50 dB. The default value should be 9dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 18Mbps on 802.11a radio, normal mode. The value should be in dB and in the range 0..50 dB. The default value should be 11dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 24Mbps on 802.11a radio, normal mode. The value should be in dB and in the range 0..50 dB. The default value should be 14dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 36Mbps on 802.11a radio, normal mode. The value should be in dB and in the range 0..50 dB. The default value should be 18dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 48Mbps on 802.11a radio, normal mode. The value should be in dB and in the range 0..50 dB. The default value should be 22dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 54Mbps on 802.11a radio, normal mode. The value should be in dB and in the range 0..50 dB. The default value should be 25dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 12Mbps on 802.11a radio, turbo mode. The value should be in dB and in the range 0..50 dB. The default value should be 6dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 18Mbps on 802.11a radio, turbo mode. The value should be in dB and in the range 0..50 dB. The default value should be 7dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 24Mbps on 802.11a radio, turbo mode. The value should be in dB and in the range 0..50 dB. The default value should be 9dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 36Mbps on 802.11a radio, turbo mode. The value should be in dB and in the range 0..50 dB. The default value should be 11dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 48Mbps on 802.11a radio, turbo mode. The value should be in dB and in the range 0..50 dB. The default value should be 14dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 72Mbps on 802.11a radio, turbo mode. The value should be in dB and in the range 0..50 dB. The default value should be 18dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 96Mbps on 802.11a radio, turbo mode. The value should be in dB and in the range 0..50 dB. The default value should be 22dB.

OBJECT-TYPE

This is to specify the minimum required SNR for data rate of 108Mbps on 802.11a radio, turbo mode. The value should be in dB and in the range 0..50 dB. The default value should be 25dB.

OBJECT-TYPE

This is to specify average SNR threshold for data rate increase. The value should be in dB and in the range 0..50 dB. The default value should be 4 dB.

OBJECT-TYPE

This is to specify average SNR threshold for data rate decrease. The value should be in dB and in the range 0..50 dB. The default value should be 6 dB.

OBJECT-TYPE

This is to specify SNRreq threshold for data rate reduction. The value should be in dB and in the range 0..50 dB. The default value should be 3 dB.

OBJECT-TYPE

This object specifies the threshold percentage of retransmissions for DDRS data rate increase.

OBJECT-TYPE

This object specifies the threshold percentage of retransmissions for DDRS data rate decrease.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object represents the MAC address of BSU to which the SU is registered.

OBJECT-TYPE

This object represents the Transmit Data Rate of the SU.

OBJECT-TYPE

This object represents the Transmit Data Rate of the BSU to which the SU is registered.

OBJECT-TYPE

The current signal level calculated over all inbound packets. This variable indicates the running average of the SU's local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current noise level calculated over all inbound packets. This variable indicates the running average of the SU's local noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current remote signal level calculated over the inbound packets received at SU, sent by the BSU. This variable indicates the running average of the SU's Rx Signal level(i.e. BSU's Tx Signal level) all registered stations of the remote signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current remote noise level calculated over the inbound packets received at SU, sent by the BSU. This variable indicates the running average of the SU's Rx Noise level(i.e. BSU's Tx Noise level) all registered stations of the remote noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table contains the Network IP configuration for the network interface(s) of the device. For bridge mode, only the address assigned to the Ethernet interface (index 1) will be used.

OBJECT-TYPE

This object represents an entry for the network IP configuration for each interface in the system.

OBJECT-TYPE

This object represents an index or interface number in the network IP configuration table.

OBJECT-TYPE

This object represents the IP Address of the network interface.

OBJECT-TYPE

This object represents the subnet mask of the network interface.

OBJECT-TYPE

This object represents the IP address of the gateway or router of the device.

OBJECT-TYPE

The default value inserted into the Time-To-Live (TTL) field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.

OBJECT-TYPE

This object identifies if the device is configured to be assigned a static or dynamic IP address using a DHCP client.

OBJECT-IDENTITY

OBJECT-TYPE

This object represents the read-only community name used in the SNMP protocol. This object is used for reading objects from the SNMP agent. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This objecgt represents the read-write community name used in the SNMP protocol. This object is used for reading and writing objects to and from the SNMP Agent. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object reflects the number of entries in the Management IP Access Table.

OBJECT-TYPE

This table is used configure management stations that are authorized to manage the device. This table applies to the supported management services/interfaces (SNMP, HTTP, and Telnet). This table is limited to 20 entries.

OBJECT-TYPE

This object identifies an entry in the Management IP Access Table.

OBJECT-TYPE

This object represents the index for the Management IP Access Table.

OBJECT-TYPE

This object represents the IP address of the management station authorized to manage the device.

OBJECT-TYPE

This object represents the IP subnet mask. This object can be used to grant access to a complete subnet.

OBJECT-TYPE

This object is used to control the interface access for each table entry in the Management IP Access Table.

OBJECT-TYPE

This object is used for an optional comment associated to the Management IP Access Table entry.

OBJECT-TYPE

This object is used to enable, disable, delete, or create an entry in the Management IP Access Table.

OBJECT-TYPE

This table contains the information regarding the trap host that will receive SNMP traps sent by the device. This table is limited 10 entries.

OBJECT-TYPE

This object identifies an entry in the SNMP Trap Host Table.

OBJECT-TYPE

This object is used as an index for the SNMP Trap Host Table.

OBJECT-TYPE

This object represents the IP address of the management station that will receive SNMP Traps from the device.

OBJECT-TYPE

This object represents the password that is sent with the SNMP trap messages to allow the host to accept or reject the traps. The trap host will only accept SNMP traps if this password matches the host's password. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object is used for an optional comment associated to the SNMP Trap Host Table entry.

OBJECT-TYPE

This object is used to enable, disable, delete, create an entry in the SNMP Trap Host Table.

OBJECT-TYPE

This object is used to control the interface access for SNMP based management (not HTTP and Telnet).

OBJECT-TYPE

This object is used to provide additional information in case of an SNMP error.

OBJECT-TYPE

This object is used to enable or disable the Management IP Access Table. If this object is disabled, the check based on source IP address for the enteries in the Management IP Access Table will not be performed.

OBJECT-TYPE

This object is used to configure the SNMP trap/notification type that will be generated.

OBJECT-TYPE

This object is used to enable or disable the secure Management feature for the Access Point. With this object enabled, view based access control will be enforced on all forms of management including SNMPv1/v2c, HTTP, WEB, HTTPS, SSH, serial, and Telnet. Also SNMPv3 user security model will be enabled. The default SNMPv3 user is defined as userName 'administrator', with SHA authentication and DES privacy protocols.

OBJECT-TYPE

This object represents the SNMPv3 administrator authentication password. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents the SNMPv3 administrator privacy password. This object should be treated as write-only and returned as asterisks.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to passthru (allow) or block (deny) packets with protocols in the protocol filter table.

OBJECT-TYPE

This table contains the two byte hexadecimal values of the protocols. The packets whose protocol field matches with any of the entries in this table will be forwarded or dropped based on value of oriProtocolFilterFlag. This table is limited to 256 ethernet protocols (enteries).

OBJECT-TYPE

This object represents an entry in the protocol filter table.

OBJECT-TYPE

This object is used to index the protocol filter table.

OBJECT-TYPE

This object represents a two byte hexadecimal value for the Ethernet protocol to be filtered (the protocol field of the Ethernet packet).

OBJECT-TYPE

This object is used as an optional comment for the ethernet protocol to be filtered.

OBJECT-TYPE

This object is used to enable, disable, delete, create the Ethernet protocols in this table.

OBJECT-TYPE

This object is isued to control protocol filtering per interface for each entry in this table.

OBJECT-TYPE

This object represents the value in the protocol field of the Ethernet packet. The value is of 4-digit Hex format. Example: The value of IP protocol is 0800. The value of ARP protocol is 0806.

OBJECT-TYPE

This object is isued to control protocol filtering per interface for the table.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable MAC Access Control feature/filter in the device.

OBJECT-TYPE

This flag determines whether the stations with MAC addresses listed in the access control table will be allowed or denied access. This flag is used only if oriAccessControlStatus is enabled. This table is limited to 1000 MAC Address entries.

OBJECT-TYPE

This table contains the information about MAC addresses of the wireless stations that are either allowed or disallowed access (based on oriAccessControlOperation) through this device. This table is used only if oriAccessControlStatus is enabled.

OBJECT-TYPE

This object represents the entry in the access control table.

OBJECT-TYPE

This object is used as an index for the access control table.

OBJECT-TYPE

This object represents the MAC address of the wireless station that can access the device.

OBJECT-TYPE

This object is used as an optional comment associated to the access control table entry.

OBJECT-TYPE

This object is used to enable, disable, delete, create the entries in the Access Control Table.

OBJECT-IDENTITY

OBJECT-TYPE

This table provides the MAC address of the stations on the wired and the wireless interface; the MAC addresses will be given in pairs. Stations listed in the Static MAC Address filter will have no traffic forwarded by the device. This way Multicast traffic exchanged between stations or servers can be prevented, from being transmitted over the wireless medium when both stations are actually located on the wired backbone. This table is limited to 200 entries.

OBJECT-TYPE

This object identifies the entry in the Static MAC address filter table.

OBJECT-TYPE

This object is used as an index for the Static MAC address filter table.

OBJECT-TYPE

This object represents the MAC address of the station on the wired interface of the device.

OBJECT-TYPE

This mask determines the presence of wildcard characters in the MAC address of the station on the wired interface. The value F (hex digit) in the mask indicates the presence of a wildcard character and the value 0 indicates its absence.

OBJECT-TYPE

This object represents the MAC address of the station on the wireless interface.

OBJECT-TYPE

The mask that determines the presence of wildcard characters in the MAC address of the station on the wireless side. The value F (hex digit) indicates the presence of a wildcard character and the hex digit 0 indicates its absense.

OBJECT-TYPE

This object is used to enable, disable, delete, create an entry in the Static MAC Address Table.

OBJECT-TYPE

This object is used for an optional comment associated to the access control table entry.

OBJECT-IDENTITY

OBJECT-TYPE

If broadcast rate from any device (identified by its MAC address) exceeds the limit specified by this value, the device will ignore all subsequent messages issued by the particular network device, or ignore all messages of that type. Valid values for address threshold is between 0 - 255 frames per second. Initial Value is 0 (Disable Storm Threshold Protection).

OBJECT-TYPE

If multicast rate from any device (identified by its MAC address) exceeds the limit specified by this value, the device will ignore all subsequent messages issued by the particular network device, or ignore all messages of that type. Valid values for address threshold is between 0 - 255 frames per second. Initial Value is 0 (Disable Storm Threshold Protection).

OBJECT-TYPE

The table containing broadcast and multicast threshold values for each interface.

OBJECT-TYPE

This object represents an entry in the storm threshold filter table.

OBJECT-TYPE

This parameter specifies a set of Broadcast Storm thresholds for each interface/port of the device, identifying separate values for the number of Broadcast messages/second. Default value is zero, which means disabled.

OBJECT-TYPE

This parameter specifies a set of Multicast Storm thresholds for each interface/port of the device, identifying separate values for the number of Multicast messages/second. Default value is zero, which means disabled.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable port filtering.

OBJECT-TYPE

This object determines whether the stations with ports listed in the port filter table must be allowed (passthru) or denied (block) to access the device. This object is used only if oriPacketFilterStatus is enabled.

OBJECT-TYPE

This table contains the Port number of packets to be filtered. The packets whose port field matches with any of the enabled entries in this table will be blocked (dropped). This table is limited to 256 entries.

OBJECT-TYPE

This parameter represents the entry in the port filter table.

OBJECT-TYPE

This object is used as the index for the port filter table. This table supports up to 256 entries.

OBJECT-TYPE

This object represents the port number of the packets to be filtered.

OBJECT-TYPE

This object specifies the port type.

OBJECT-TYPE

This object is used to control port filtering per interface for each entry in the table.

OBJECT-TYPE

This object is used for an optional comment associated to the port filter table entry.

OBJECT-TYPE

This object is used to enable, disable, delete, create an entry in the Port Filter Table.

OBJECT-IDENTITY

OBJECT-TYPE

The table entries for broadcast filters. This table shall contain 5 entries.

OBJECT-TYPE

This object represents an entry in the broadcast filtering table.

OBJECT-TYPE

This object represents the index of the Broadcast Filtering table.

OBJECT-TYPE

This object represents the broadcast protocol name to be filtered.

OBJECT-TYPE

This object represents the direction of the broadcast filter. The filter can be enabled for Ethernet to Wireless, Wireless to Ethernet, or both directions.

OBJECT-TYPE

This object is used to enable or disable the broadcast filter table enteries.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the Packet Forwarding feature.

OBJECT-TYPE

This object represents the MAC Address to which all frames will be forwarded by the device.

OBJECT-TYPE

This object is used to configure the interface or port that frames will be forwarded to. If this object is not configured, value set to zero, then the bridge will forward the packets on the interface or port the MAC address was learned on. If this object is not configured, value set to zero, and the bridge has not yet learned the MAC address then the frames will be forwarded on all interfaces and ports.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to control IntraBSS Traffic. If this object is set to the passthru, then IBSS traffic will be allowed; if this object is set to block, then IBSS traffic will be denied.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable/disable IntraCell Blocking/Filtering.

OBJECT-TYPE

The MAC table entries for IntraCell Blocking filters. This table can contain up to a maximum of 250 entries.

OBJECT-TYPE

This object represents the entry in the IntraCell Blocking MAC Table.

OBJECT-TYPE

This object is used as the index to the IntraCell Blocking MAC Table.

OBJECT-TYPE

This object represents the MAC address of the SU which is allowed to communicate with other SUs with the same group ID.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 1.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 2.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 3.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 4.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 5.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 6.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 7.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 8.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 9.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 10.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 11.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 12.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 13.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 14.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 15.

OBJECT-TYPE

This object is used to activate/deactivate Group ID 16.

OBJECT-TYPE

This object is used to enable, disable, delete, create the entries in the IntraCell Blocking MAC Table.

OBJECT-TYPE

The Group table entries for IntraCell Blocking Group IDs. This table can contain a maximum of 16 entries.

OBJECT-TYPE

This object represents the entry in the IntraCell Blocking Group Table.

OBJECT-TYPE

This object is used as the index to the IntraCell Blocking Group Table.

OBJECT-TYPE

This object represents the group name.

OBJECT-TYPE

This object is used to enable, disable, delete, create the entries in the IntraCell Blocking Group Table.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable/disable the Security Gateway feature.

OBJECT-TYPE

This object represents the Security Gateway MAC Address to which all frames will be forwarded by the device.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table represents the RADIUS servers that the device will communicated with for client authentication. Usually this table should have two members representing the primary and secondary (backup) RADIUS Authentication Servers.

OBJECT-TYPE

This object represents an entry in the RADIUS Authentication Server Table.

OBJECT-TYPE

This object is used as an index to the RADIUS Authentication Server Table.

OBJECT-TYPE

This object indicates if the RADIUS server will provide Authentication service, Accounting service, or both.

OBJECT-TYPE

This object identifies if the RADIUS server entry is enabled or disabled.

OBJECT-TYPE

This object represents the IP address of the RADIUS server.

OBJECT-TYPE

This object represents the RADIUS server authentication port - the default value is 1812.

OBJECT-TYPE

This object represents the shared secret between the RADIUS server and client. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents the time (in seconds) for which the RADIUS client will wait, until another authentication request is sent to the server.

OBJECT-TYPE

This object represents the number of retransmissions of authentication requests by the RADIUS Client to the Server.

OBJECT-TYPE

This object represents the number of RADIUS Access Requests messages transmitted from the client to the server since client startup.

OBJECT-TYPE

This object represents the number of RADIUS Access Requests retransmitted by the client to the server since system startup.

OBJECT-TYPE

This object indicates the number of RADIUS Access Accept messages received since system startup.

OBJECT-TYPE

This object represents the number of RADIUS Access Challenges messages received since system startup.

OBJECT-TYPE

This object represents the number of RADIUS Access Rejects messages received since system startup.

OBJECT-TYPE

This object represents the number of malformed RADIUS Access Response messages received since system startup.

OBJECT-TYPE

This object represents the number of malformed RADIUS Access Response messages containing invalid authenticators received since system startup.

OBJECT-TYPE

This object represents the total number of timeouts for RADIUS Access Request messages since system startup.

OBJECT-TYPE

This object is used to specify the RADIUS Server host name or IP Address.

OBJECT-TYPE

This object is used to specify the addressing format for configuring the RADIUS Server. If this object is configured to IP Address, then IP address should be used to specify the server. If this object is configured to name, then the host name should be specified.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the RADIUS Accounting service. This object has been deprecated.

OBJECT-TYPE

This parameter represents the inactivity or idle timeout in minutes after which an Accounting Stop request is sent to the RADIUS Accounting server - the default value is 5 minutes. This object has been deprecated.

OBJECT-TYPE

This table represents the RADIUS servers that the device will communicated with for accounting. Usually this table should have two members representing the primary and secondary (backup) RADIUS Accounting Servers. This object has been deprecated.

OBJECT-TYPE

This object represents an entry into the RADIUS Accouting Server Table. This object has been deprecated.

OBJECT-TYPE

This object is used as the index to the RADIUS Server Accounting table. This object has been deprecated.

OBJECT-TYPE

This object indicates if the RADIUS server will provide Authentication service, Accounting service, or both. This object has been deprecated.

OBJECT-TYPE

This object identifies if the RADIUS server entry is enabled or disabled. This object has been deprecated.

OBJECT-TYPE

This object represents the IP address of the RADIUS server. This object has been deprecated.

OBJECT-TYPE

This object represents the RADIUS server accounting port - the default value is 1813. This object has been deprecated.

OBJECT-TYPE

This object represents the shared secret between the RADIUS server and client. This object should be treated as write-only and returned as asterisks. This object has been deprecated.

OBJECT-TYPE

This object represents the time (in seconds) for which the RADIUS client will wait, until another accounting request is sent to the server. This object has been deprecated.

OBJECT-TYPE

This object represents the number of retransmissions of accounting requests by the RADIUS Client to the Server. This object has been deprecated.

OBJECT-TYPE

This object represents the number of Accounting Requests messages sent since system startup. This object has been deprecated.

OBJECT-TYPE

This object represents the number of Accounting Requests messages retransmitted sent since system startup. This object has been deprecated.

OBJECT-TYPE

This object represents the number of Accounting Response messages received since system startup. This object has been deprecated.

OBJECT-TYPE

This object represents the number of Accounting Response messages which contain invalid authenticators received since system startup. This object has been deprecated.

OBJECT-TYPE

This object is used to specify the RADIUS Server host name or the IP Address. This object has been deprecated.

OBJECT-TYPE

This object is used to specify the addressing format for configuring the RADIUS Server. If this object is configured to IP Address, then IP address should be used to specify the server. If this object is configured to name, then the host name should be specified. This object has been deprecated.

OBJECT-TYPE

This object is used to specify the interval in seconds at which RADIUS accounting update messages will be sent. This object has been deprecated.

OBJECT-TYPE

This counter represents the total number of RADIUS access-response messages received from an unknown address since system startup.

OBJECT-TYPE

This object is used to enables RADIUS Access Control based on wireless stations MAC Address.

OBJECT-TYPE

This object represents the authorization lifetime for a certain MAC based RADIUS authenticated client. A value of zero (0) means that re-authorization is disabled. The units for this object is seconds.

OBJECT-TYPE

This object is used to configure the MAC Address format that is to be used for communication with the RADIUS Server. Examples of MAC Address Format are: - Dash Delimited: 00-11-22-AA-BB-CC - Colon Delimited: 00:11:22:AA:BB:CC - Single Dash Delimited: 001122-AABBCC - No Delimiter: 001122AABBCC

OBJECT-TYPE

This object is used to enable/disable local user support when RADIUS based management is enabled.

OBJECT-TYPE

This object is the password to access the device when using the local username - root. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object is used to configure the RADIUS Server profile that will be used for RADIUS based management access. The RADIUS profile is defined in the RADIUS Server Table in the orinocoRADIUSSvrProfile group.

OBJECT-IDENTITY

OBJECT-TYPE

This table represents the RADIUS server profile that the device will communicated with for client authentication and/or accounting. This table has two indices - the first index indicates the profile number and the second index indicates primary and secondary/backup servers.

OBJECT-TYPE

This object represents an entry in the RADIUS Server Table.

OBJECT-TYPE

This object represents the RADIUS Server profile index.

OBJECT-TYPE

This object is a second index to the RADIUS Server table, which identifies a server bein primary or secondary/backup.

OBJECT-TYPE

This object is used to specify a unique name for the RADIUS server profile.

OBJECT-TYPE

This object is used to specify the addressing format for configuring the RADIUS Server. If this object is configured to IP Address, then IP address should be used to specify the server. If this object is configured to name, then the host name should be specified.

OBJECT-TYPE

This object is used to specify the RADIUS Server host name or IP Address.

OBJECT-TYPE

This object represents the RADIUS server authentication port - the default value is 1812.

OBJECT-TYPE

This object represents the shared secret between the RADIUS server and client. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents the time (in seconds) for which the RADIUS client will wait, until another authentication request is sent to the server.

OBJECT-TYPE

This object represents the number of retransmissions of authentication requests by the RADIUS Client to the Server.

OBJECT-TYPE

This object represents the VLAND ID that will be used to tag RADIUS messages from the client to the server.

OBJECT-TYPE

This object is used to configure the MAC Address format that is to be used for communication with the RADIUS Server. Examples of MAC Address Format are: - Dash Delimited: 00-11-22-AA-BB-CC - Colon Delimited: 00:11:22:AA:BB:CC - Single Dash Delimited: 001122-AABBCC - No Delimiter: 001122AABBCC

OBJECT-TYPE

This object represents the authorization lifetime for a certain MAC based RADIUS authenticated client. A value of zero (0) means that re-authorization is disabled. The units for this object is seconds.

OBJECT-TYPE

This parameter represents the client idle timeout in minutes. Once this timer has expired an Accounting Stop request is sent to the RADIUS Accounting Server.

OBJECT-TYPE

This object is used to specify the interval in seconds at which RADIUS accounting update messages will be sent. This object is defined in minutes; a value of zero (0) disables the accouting updates.

OBJECT-TYPE

This object represents the status of the RADIUS Server profile.

OBJECT-TYPE

This counter represents the total number of RADIUS access-response messages received from an unknown address since system startup.

OBJECT-TYPE

This table is used to store RADIUS Authentication Client Statistics for the configured profiles.

OBJECT-TYPE

This object represents an entry, primary and secondary/backup, in the RADIUS Authentication Client Statistics table.

OBJECT-TYPE

This object is used as an index to the RADIUS Authentication Client Statistics Table.

OBJECT-TYPE

This object is used as an secondary index to the RADIUS Authentication Client Statistics Table, which is used to indicate primary and secondary/backup server statistics.

OBJECT-TYPE

This object represents the number of RADIUS Access Requests messages transmitted from the client to the server since client startup.

OBJECT-TYPE

This object represents the number of RADIUS Access Requests retransmitted by the client to the server since system startup.

OBJECT-TYPE

This object indicates the number of RADIUS Access Accept messages received since system startup.

OBJECT-TYPE

This object represents the number of RADIUS Access Challenges messages received since system startup.

OBJECT-TYPE

This object represents the number of RADIUS Access Rejects messages received since system startup.

OBJECT-TYPE

This object represents the number of malformed RADIUS Access Response messages received since system startup.

OBJECT-TYPE

This object represents the number of malformed RADIUS Access Response messages containing invalid authenticators received since system startup.

OBJECT-TYPE

This object represents the total number of timeouts for RADIUS Access Request messages since system startup.

OBJECT-TYPE

This table is used to store RADIUS Accounting Client Statistics for the configured profiles.

OBJECT-TYPE

This object represents an entry, primary and secondary/backup, in the RADIUS Accounting Client Statistics table.

OBJECT-TYPE

This object is used as an index to the RADIUS Accounting Client Statistics Table.

OBJECT-TYPE

This object is used as an secondary index to the RADIUS Accounting Client Statistics Table, which is used to indicate primary and secondary/backup server statistics.

OBJECT-TYPE

This object represents the number of RADIUS Accounting Requests messages transmitted from the client to the server since client startup.

OBJECT-TYPE

This object represents the number of RADIUS Accounting Requests retransmitted by the client to the server since system startup.

OBJECT-TYPE

This object indicates the number of RADIUS Accounting Response messages received since system startup.

OBJECT-TYPE

This object represents the number of malformed RADIUS Access Response messages containing invalid authenticators received since system startup.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable telnet access and to specify the maximum number of active telnet sessions. When this object is set to 0, telnet access is disabled. When this object is set to something greater than 0, then it specifies the maximum number of active telnet sessions. This object has been deprecated.

OBJECT-TYPE

This object is the password to access the device via the telnet interface. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents the TCP/IP port for which the telnet daemon/server will be accessible.

OBJECT-TYPE

This object represents the telnet login timeout in seconds.

OBJECT-TYPE

This object represents the telnet inactivity/idle timeout in seconds.

OBJECT-TYPE

This object is used to control interface access for telnet based management.

OBJECT-TYPE

This object is used to enable or disable CLI access configuration using secure shell.

OBJECT-TYPE

This object is used create or delete the SSH Public Host key of the device.

OBJECT-TYPE

This object gives the fingerprint of the SSH Public Host key stored on the device.

OBJECT-TYPE

This object is used to enable/disable RADIUS Based Authentication for telnet based management.

OBJECT-IDENTITY

OBJECT-TYPE

This object represents the IP address of the TFTP server.

OBJECT-TYPE

This object represents the filename to upload or download to the TFTP server.

OBJECT-TYPE

This object is used for the device to know what type of file is being uploaded or downloaded.

OBJECT-TYPE

This object represents the TFTP operation to be executed. The upload function shall transfer the specified file from the device to the TFTP server. The download function shall transfer the specified file from the TFTP server to the device. The download and reboot option, will perform the download and then reboot the device.

OBJECT-TYPE

This objects represents the file transfer mode for the TFTP protocol.

OBJECT-TYPE

This object represents the TFTP operation status. When a TFTP operation is idle (not in progress) this object will be set to 1. When a TFTP operation is in progress this object will be set to 2. When a TFTP operation has been successful this object will be set to 3. When a TFTP operation has failed this object will be set to 4.

OBJECT-TYPE

This objects is used to enable/disable the Auto Configuration feature. This feature allows for a configuration file to be downloaded from a TFTP server so the AP can be configured via a config file.

OBJECT-TYPE

This object is used to configure the name of the configuration file to be downloaded using the Auto Configuration feature. This filename can be configured directly via the end user or can be retrieved in the DHCP response message when the AP is configured for dynamic IP address assignment type.

OBJECT-TYPE

This object is used to configure the TFTP server IP Address. This object can be configured directly via the end user or can be retrieved in the DHCP response message when the AP is configured for dynamic IP address assignment type.

OBJECT-TYPE

On selection of this option, the software will downgrade the configuration file to the specified release from the current release

OBJECT-IDENTITY

OBJECT-TYPE

This object represents the baud rate for the serial interface - the default value is 9600.

OBJECT-TYPE

This object represents the serial interface data bits - the default value is 8.

OBJECT-TYPE

This object is used for the serial interface parity check - the default value is none.

OBJECT-TYPE

This object indicates the serial interface stop bits - the default value is 1.

OBJECT-TYPE

This object is used for the serial interface flow control - the default value is none.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the IAPP feature.

OBJECT-TYPE

This object represents interval in seconds for performing an IAPP announce operation by the device.

OBJECT-TYPE

This object indicates the amount of time in seconds the device waits to send an IAPP announce response after an announce request message is sent.

OBJECT-TYPE

This object represents the time in milliseconds the device waits before it resends a handover response message. This object is originally given in kuseconds, but has been converted to milliseconds.

OBJECT-TYPE

This object indicates the maximum amount of retransmission sent by the device for a handover request message.

OBJECT-TYPE

This object represents the total number of IAPP Announce Request Messages sent since system startup.

OBJECT-TYPE

This object represents the total number of IAPP Announce Request Messages received since system startup.

OBJECT-TYPE

This object represents the total number of IAPP Announce Response Messages sent since system startup.

OBJECT-TYPE

This object represents the total number of IAPP Announce Response Messages received since system startup.

OBJECT-TYPE

This object represents the total number of IAPP Handover Request messages sent since system startup.

OBJECT-TYPE

This object represents the total number of IAPP Handover Request messages received since system startup.

OBJECT-TYPE

This object represents the total number of IAPP Handover Request retransmissions since system startup.

OBJECT-TYPE

This object represents the total number of IAPP Handover Response messages sent since system startup.

OBJECT-TYPE

This object represents the total number of IAPP Handover Response messages received since system startup.

OBJECT-TYPE

This object represents the total number of IAPP packets dropped due to erroneous information within the packet since system startup.

OBJECT-TYPE

This object represents the total number of client that have roamed from one device to another. This parameter is per device and not a total counter of all the roaming clients for all devices on the network.

OBJECT-TYPE

This table contains a list of devices on the network that support IAPP and have the feature enabled.

OBJECT-TYPE

This object represents an entry in the IAPP table, which essentially is a device that supports IAPP and has the feature enabled.

OBJECT-TYPE

This object is used as the index for the IAPP MAC-IP table.

OBJECT-TYPE

This object represents the System Name of the IAPP enabled device.

OBJECT-TYPE

This object represents the IP Address of the IAPP enabled device.

OBJECT-TYPE

This object represents the BSSID (MAC address of wireless interface) of the IAPP enabled device.

OBJECT-TYPE

This object represents the ESSID (network name) of the IAPP enabled device.

OBJECT-TYPE

This object is used to determine whether to send announce request on start.

OBJECT-IDENTITY

OBJECT-TYPE

The value of this object determines the time (in seconds) that a link test will continue without any SNMP requests for a Link Test Table entry. When the time expires the Link Test Table is cleared.

OBJECT-TYPE

This object indicates the interval (in milliseconds) between sending link test frames to a station.

OBJECT-TYPE

When this object is set to 2, the device will send out an explore request on all 802.11 interfaces and from the results build the Link Test table. This table is valid only while this object is set to 3.

OBJECT-TYPE

This table contains the information for the stations currently associated with the access point.

OBJECT-TYPE

This object represents the entry in the Remote Link Test table.

OBJECT-TYPE

This object represents a unique value for each station. The value for each station must remain constant at least from one explore to the next.

OBJECT-TYPE

When this object is set to 2 the device will initiate a link test sequence with this station.

OBJECT-TYPE

This object identifies the name of the station whom which the link test is being performed.

OBJECT-TYPE

This object represents the MAC address that will be mapped to the IP Address of the station.

OBJECT-TYPE

This object represents the profile/capabilities for this station.

OBJECT-TYPE

The current signal level (in dB) for the link test from this station. This object indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

The current noise level (in dB) for the link test to this station. This object indicates the running average of the local noise level.

OBJECT-TYPE

The current signal to noise ratio for the link test to this station.

OBJECT-TYPE

The minimum signal level during the link test to this station.

OBJECT-TYPE

The minimum noise level during the link test to this station.

OBJECT-TYPE

The minimum signal to noise ratio during the link test to this station.

OBJECT-TYPE

The maximum signal level during the link test to this station.

OBJECT-TYPE

The maximum noise level during the link test to this station.

OBJECT-TYPE

The maximum signal to noise ratio during the link test to this station.

OBJECT-TYPE

The total number of frames sent at 1 Mbit/s speed during the link test to this station.

OBJECT-TYPE

The total number of frames sent at 2 Mbit/s speed during the link test to this station.

OBJECT-TYPE

The total number of frames sent at 5.5 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to this station.

OBJECT-TYPE

The total number of frames sent at 11 Mbit/s (for Turbo-8, it is 8 Mbit/s) speed during the link test to this station.

OBJECT-TYPE

The current signal level for the link test to the remote station or access point.

OBJECT-TYPE

The current noise level for the link test to the remote station or access point device.

OBJECT-TYPE

The current signal to noise ratio for the link test to the remote station or access point device.

OBJECT-TYPE

The minimum signal level during the link test to the remote station or access point device.

OBJECT-TYPE

The minimum noise level during the link test to the remote station or access point device.

OBJECT-TYPE

The minimum signal to noise ratio during the link test to the remote station or access point device.

OBJECT-TYPE

The maximum signal level during the link test to the remote station or access point device.

OBJECT-TYPE

The maximum noise level during the link test to the remote station or access point device.

OBJECT-TYPE

The maximum signal to noise ratio during the link test to the remote station or access point device.

OBJECT-TYPE

The total number of frames sent at 1 Mbit/s speed during the link test to the remote station or access point device.

OBJECT-TYPE

The total number of frames sent at 2 Mbit/s speed during the link test to the remote station or access point device.

OBJECT-TYPE

The total number of frames sent at 5.5 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to the remote station or access point device.

OBJECT-TYPE

The total number of frames sent at 11 Mbit/s (for Turbo-8, it is 5 Mbit/s) speed during the link test to the remote station or access point device.

OBJECT-TYPE

This object represents the wireless interface number to which the Client has sent the Explore Response Message.

OBJECT-TYPE

The Wireless Standard for example IEEE 802.11, 802.11b, 802.11a, or 802.11g being used by the remote station.

OBJECT-TYPE

This table contains counters for the data rates for the stations currently associated to the access point.

OBJECT-TYPE

This object represents the entry in the Remote Link Test data rate counter table.

OBJECT-TYPE

This object is the second index to the Link Test Data Rate Counter Table. The data rates negotiated by the access point and client station will represent an index into this table. The data rates are defined in units of 500 Kbps.

OBJECT-TYPE

The total number of frames sent at the data rate value of the index during the link test to the remote station or access point device.

OBJECT-TYPE

The total number of frames sent at the data rate value of the index (oriLinkTestDataRateTableindex) during the link test to the client station indenfied by the index (oriLinkTestTableIndex).

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the link integrity functionality.

OBJECT-TYPE

This object is used to set the poll interval (in milliseconds) for the link integrity check. The valid values for this objects are multiples of 500 milliseconds, a value of zero is not supported.

OBJECT-TYPE

This object is used to set the number of retransmissions for the link integrity check.

OBJECT-TYPE

This table contains the target IP addresses in order to perform the link integrity check. This table is limited to 5 entries.

OBJECT-TYPE

This object identifies the entry in the link integrity target table.

OBJECT-TYPE

This object is used as an index for the link integrity target table.

OBJECT-TYPE

This object represents the IP address of the target machine for the link integrity check.

OBJECT-TYPE

This object is used as an optional comment associated to the link integrity table entry.

OBJECT-TYPE

This object is used to enable, disable, or delete an entry in the link integrity table.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to set the interval of GPR message (in 5ms step), 0 = disable GPR.

OBJECT-TYPE

This object is used to set the maximum actived SU per AP.

OBJECT-TYPE

This object is used to set the bandwidth allocated for E911calls.

OBJECT-TYPE

This object is used to set the bandwidth allocated for roaming SU.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure Quality of Service policies to be used in the Access Point.

OBJECT-TYPE

This object represents entries in the QoS Policy Table.

OBJECT-TYPE

This object is used as the primary index to the QoS Policy Table.

OBJECT-TYPE

This object is used as the secondary index to the QoS Policy Table.

OBJECT-TYPE

This object is used to specify a name for the QoS Policy.

OBJECT-TYPE

This object is used to specify the QoS policy type.

OBJECT-TYPE

This object is used to configure the QoS priority mapping. The index from either the QoS 802.1D to 802.1p mapping table or the index from the 802.1D to IP DSCP mapping table should be specified depending on the policy type. For Layer 2 polices, an index from the QoS 802.1D to 802.1p mapping table should be specified. For Layer 3 policies, an index from the QoS 802.1D to IP DSCP mapping table should be specified. If a spectralink policy is configured, then this object is not used.

OBJECT-TYPE

This object is used to enable or disable QoS markings.

OBJECT-TYPE

The object is used to configure the QoS Policy Table row status.

OBJECT-TYPE

This table is used to configure Quality of Service mappings between 802.1D and 802.1p priorities.

OBJECT-TYPE

This object represents entries in the QoS 802.1D to 802.1p Mapping Table.

OBJECT-TYPE

This object is used as the primary index to the QoS 802.1D to 802.1p mapping table.

OBJECT-TYPE

This object is used to specify the 802.1d priority and is used as the secondary index to the 802.1D to 802.1p mapping table.

OBJECT-TYPE

This object is used to specify the 802.1D priority to be mapped to a 802.1p priority.

OBJECT-TYPE

The object is used to configure the QoS 802.1D to 802.1p mapping table row status.

OBJECT-TYPE

This table is used to configure Quality of Service mappings between 802.1D to IP DSCP priorities.

OBJECT-TYPE

This object represents entries in the 802.1D to IP DSCP Mapping Table.

OBJECT-TYPE

This object is used as the primary index to the 802.1D to IP DSCP mapping table.

OBJECT-TYPE

This object is used to specify the 802.1D priority and is used as the secondary index to the 802.1D to IP DSCP mapping table.

OBJECT-TYPE

This object is used to specify IP DSCP lower limit.

OBJECT-TYPE

This object is used to specify IP DSCP upper limit.

OBJECT-TYPE

The object is used to configure the 802.1D to IP DSCP mapping table row status.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates if the DHCP server is enabled or disabled in the device.

OBJECT-TYPE

This table contains the pools of IP Addresses that the DHCP server will assign to the DHCP clients. This table is limited to 20.

OBJECT-TYPE

This object represents entries in the DHCP IP Address Pool Table.

OBJECT-TYPE

This object is used as the index for the IP Address Pool table.

OBJECT-TYPE

This object represents the start IP address for this DHCP IP Address IP Pool Table entry.

OBJECT-TYPE

This object represents the end IP address for this DHCP IP Address IP Pool Table entry.

OBJECT-TYPE

This object represents the width or number of IP Address in the DHCP IP Address Pool table entry.

OBJECT-TYPE

This object represents the default lease time, in seconds, for the IP address assigned by the DHCP server to the DHCP client.

OBJECT-TYPE

This object represents the maximum lease time in seconds for the IP address assigned by the DHCP server to the DHCP client.

OBJECT-TYPE

This object represents an optional comment for this table entry.

OBJECT-TYPE

The object indicates the status of the DHCP IP Address Pool Table entry.

OBJECT-TYPE

This object represents the IP Address of the gateway or router that the DHCP Server will assign to the DHCP client.

OBJECT-TYPE

This object represents the subnet mask to be provided to DHCP clients. This object is the same as the subnet mask for the device.

OBJECT-TYPE

This object represents the number of entries in the DHCP IP Address Pool Table.

OBJECT-TYPE

This object represents the primary DNS Server IP Address to be assinged to a DHCP Client.

OBJECT-TYPE

This object represents the secondary DNS Server IP Address to be assinged to a DHCP Client.

OBJECT-IDENTITY

OBJECT-TYPE

This object represents the DHCP client ID.

OBJECT-TYPE

This object indicates to which interface a DHCP Request in sent when the unit is in routing mode

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable and disable the DHCP Relay functionality.

OBJECT-TYPE

This table contains a list of DHCP servers to which the DHCP Agent will communicate with.

OBJECT-TYPE

This object represents and entry in the DHCP Server table.

OBJECT-TYPE

This object is used as the index to this table. This table is limited to 10 entries.

OBJECT-TYPE

This object represents the IP address of the DHCP server that shall receive DHCP requests from the device.

OBJECT-TYPE

This object represents an optional comment in order to provide additional information or a unique identifier for the DHCP server (for example the server system name).

OBJECT-TYPE

This object is used to enable, disable, delete or create an entry in the DHCP Server Table.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to control interface access for HTTP based management.

OBJECT-TYPE

This object represents the login password in order to manage the device via a standard web browser. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents the TCP/IP port by which the HTTP server will be accessible.

OBJECT-TYPE

This table is used to store the different website interfaces stored in the device. Different interfaces can be used to support multiple languages, user levels (novice, expert), etc.

OBJECT-TYPE

This object represents an entry is the HTTP website name table.

OBJECT-TYPE

This objects represents the index to the website interface table.

OBJECT-TYPE

This object represents the filename under which the website interface is stored in the device.

OBJECT-TYPE

This object represents the language of the website interface.

OBJECT-TYPE

This object provides a description for the website interface.

OBJECT-TYPE

This object is used to enable, disable, or delete a website interface file.

OBJECT-TYPE

This object is used for the automatic refresh delay for the website pages.

OBJECT-TYPE

This object is used to configure the link in the web interface for where help information can be retrieved.

OBJECT-TYPE

This object is used to enable or disable SSL on HTTP based management.

OBJECT-TYPE

This object is used to specify the SSL certificate passphrase on HTTP based management. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object is used to enable or disable the HTT setup wizard. The user can manually disable this functionality or when the setup wizard completes it process successfully it sets this object to disable.

OBJECT-TYPE

This object is used to enable/disable RADIUS Based Authentication for HTTP based management.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used in to configure the WDS feature in the device.

OBJECT-TYPE

This object represents an entry in the WDS table. Note this table is index by ifIndex and WDS table index.

OBJECT-TYPE

This object represents the WDS port number.

OBJECT-TYPE

This object is used to enable or disable a WDS table entry (link).

OBJECT-TYPE

This object represents the partner MAC address for a WDS table entry (link).

OBJECT-TYPE

This table is used in to configure the WDS security modes for all entries in the WDS table.

OBJECT-TYPE

This object represents an entry in the WDS security table. Note this table is index by ifIndex since the security configuration will apply for all the WDS links per interface.

OBJECT-TYPE

This object is used to configure the WDS security mode. Currently the supported WDS security modes are none and wep.

OBJECT-TYPE

This object represents the WDS Encryption Key 0. When the WDS security mode is configured to wep, this object must be configured to a valid value. This object should be treated as write-only and returned as asterisks.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to provide additional information on traps.

OBJECT-TYPE

This object is used to store the MAC address of the device that has sent a trap.

OBJECT-TYPE

This object is used to store the IP Address of the TFTP server.

OBJECT-TYPE

This object is used to store the name of the file on which the TFTP operation has occurred.

OBJECT-TYPE

This object is used to store the TFTP operation that failed, either download or upload.

OBJECT-TYPE

This object is used to store the IP address of the unauthorized manager that has attempted to manage the device.

OBJECT-TYPE

This trap variable is used to specify the client authentication method/type that failed. The authentication methods/types are dependant on the device and can range from the following: - MAC Access Control Table - RADIUS MAC Authentication - 802.1x Authentication specifying the EAP-Type - WORP Mutual Authentication - SSID Authorization Failure specifying the SSID - VLAN ID Authorization Failure specifying the VLAN ID

OBJECT-TYPE

This object represents a counter for the number of unauthorized SNMP managers that have attempted to modify and/or view the devices setup. When this number is incremented a trap should be sent out notifying the trap host(s) that an unauthorized station has attempted to configure or monitor the device the count should also be sent out in the trap message.

OBJECT-TYPE

This object is used to inform what task has been suspended on the device.

OBJECT-TYPE

This object is used to enable or disable the configuration related traps.

OBJECT-TYPE

This object is used to enable or disable the security related traps.

OBJECT-TYPE

This object is used to enable or disable the wireless interface/card related traps.

OBJECT-TYPE

This object is used to enable or disable the operational related traps.

OBJECT-TYPE

This object is used to enable or disable the flash memory related traps.

OBJECT-TYPE

This object is used to enable or disable the TFTP related traps.

OBJECT-TYPE

This object is used to enable or disable the Image related traps.

OBJECT-TYPE

This object is used to store the MAC Address of an unauthorized client station.

OBJECT-TYPE

This object is used to determine on which Wireless Card, PC Card A or PC Card B, a wireless TRAP has occured on.

OBJECT-TYPE

This object is used to enable or disable the ADSL interface related traps.

OBJECT-TYPE

This object is used to enable or disable the WORP related traps.

OBJECT-TYPE

This object is used to store the interface number.

OBJECT-TYPE

This object is used to store filename used for Batch CLI execution.

OBJECT-TYPE

This object is used to store message from Batch CLI execution.

OBJECT-TYPE

This object is used to store line number of command executed in Batch CLI.

OBJECT-TYPE

This object is used to store the DHCP Server IP Address from which the access point has received an IP address as a result of the a DHCP client request.

OBJECT-TYPE

This object is a trap variable/object to store an IP address.

OBJECT-TYPE

This object is a trap variable/object to store a subnet mask.

OBJECT-TYPE

This object is a trap variable/object to store a default router or gateway IP address.

OBJECT-IDENTITY

This is the configuration related trap/notification group.

OBJECT-IDENTITY

This is the security related trap/notification group.

OBJECT-IDENTITY

This is the wireless interface or wireless card related trap/notification group.

OBJECT-IDENTITY

This is the operational related trap group group.

OBJECT-IDENTITY

This is the flash memory related trap group.

OBJECT-IDENTITY

This is the TFTP related trap group.

OBJECT-IDENTITY

This is the miscellaneous trap group.

OBJECT-IDENTITY

This is the image related trap group.

OBJECT-IDENTITY

This is the WORP related trap group.

OBJECT-IDENTITY

This is the System Feature based License related trap group.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable/disable the Proxy ARP functionality in the device.

OBJECT-TYPE

This object is used to enable/disable the IP/ARP functionality in the device.

OBJECT-TYPE

This object is used to specify the IP/ARP Filtering address in the device.

OBJECT-TYPE

This object is used to specify the IP/ARP Subnet Mask in the device.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable/disable the spanning tree protocol in the device.

OBJECT-IDENTITY

OBJECT-TYPE

This object represents the supported security configuration options. This object has been deprecated.

OBJECT-TYPE

This table is used to specify the encryption key length for the wireless interface(s). This table has been deprecated.

OBJECT-TYPE

This object represents an entry in the encryption key length table. This object has been deprecated.

OBJECT-TYPE

This object represents the encryption key length, the supported key lengths are 64 bits (40 + 24 for IV), and 128 bits (104 + 24 for IV). This object has been deprecated.

OBJECT-TYPE

This object represents the encryption rekeying interval in seconds. This object has been deprecated.

OBJECT-IDENTITY

OBJECT-TYPE

This object allows to enable or disable the RAD service in the device.

OBJECT-TYPE

This object is used to identify the interval at which the RAD feature will initialize. The units of this object is minutes.

OBJECT-TYPE

This object is used to configure the interface(s) on which the RAD feature will operate on.

OBJECT-TYPE

This object is the number of seconds that have elapsed since the last successful RAD scan since the AP has started up.

OBJECT-TYPE

This object represents the number of access points that were discovered since the last RAD scan.

OBJECT-TYPE

This table is used to store the RAD scan results. Each entry represents an access point scanned in the network.

OBJECT-TYPE

This object represents an entry in the RAD scan results table.

OBJECT-TYPE

This object is used as the index to the scan results table.

OBJECT-TYPE

This object represents the MAC address of the access point detected during a RAD scan.

OBJECT-TYPE

This object represents the frequency channel of the access point.

OBJECT-TYPE

This table is used to specify the security configuration for the wireless interface(s) in the access point.

OBJECT-TYPE

This object represents an entry in the security configuration table.

OBJECT-TYPE

This object is used to provide information on the supported security modes by the wireless interface(s). The possible security modes can be: - None: no security mode enabled. - dot1x: 802.1x authentication enabled. - mixed: mixed WEP and 802.1x. - wpa: WiFi Protected Access enabled. - wpa-psk: WiFi Protected Access with Preshared Keys enabled.

OBJECT-TYPE

This object is used to configure the security mode. The supported security modes are: - None: no security mode enabled. - dot1x: 802.1x authentication enabled. - mixed: mixed WEP and 802.1x. - wpa: WiFi Protected Access enabled. - wpa-psk: WiFi Protected Access with Preshared Keys enabled.

OBJECT-TYPE

This object represents the encryption rekeying interval in seconds.

OBJECT-TYPE

This object represents the encryption key length, the supported key lengths are 64 bits (40 + 24 for IV), 128 bits (104 + 24 for IV), and 152 bits (128 + 24 for IV).

OBJECT-TYPE

This object is used to enable/disable the status of configuration reset using the hardware reset button.

OBJECT-TYPE

This object represents the configuration reset password. This object should be treated as write-only and returned as asterisks.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to configure the Rogue Scan feature per wireless network interface card.

OBJECT-TYPE

This object represents an entry in the Rogue Scan Config Table.

OBJECT-TYPE

This object is used to configure the scan mode for the wireless NIC.

OBJECT-TYPE

This object is used to configure the rogue scan cycle time for the wireless NIC.

OBJECT-TYPE

This object is used to enable/disable rogue scan on the wireless NIC.

OBJECT-TYPE

This object represents the number of stations that were discovered/detected on the device's wireless NIC A.

OBJECT-TYPE

This object represents the number of stations that were discovered/detected on the device's wireless NIC B.

OBJECT-TYPE

This object represents the aging time for the entries in RogueScanResultsTable, after which the entries are removed from RogueScanResultsTable.

OBJECT-TYPE

This object is used to remove the content/entries of RogueScanResultsTable. When this object is set, the content of the table shall be cleared.

OBJECT-TYPE

This object is used to configure the trap/notification mode for detected stations during Rogue Scan.

OBJECT-TYPE

This object is used to configure the trap/notification report type for detected stations during Rogue Scan.

OBJECT-TYPE

This table is used to store the rogue scan results. Each entry represents a rogue wireless station detected in the network.

OBJECT-TYPE

This object represents an entry in the rogue scan results table.

OBJECT-TYPE

This object is used as the index to the rogue scan results table.

OBJECT-TYPE

This object represents the type of station detected during a rogue scan.

OBJECT-TYPE

This object represents the MAC address of the station detected during a rogue scan.

OBJECT-TYPE

This object represents the frequency channel on which the rogue wireless stations was detected.

OBJECT-TYPE

This object represents the signal to noise ration (SNR) for the station detected during a rogue scan.

OBJECT-TYPE

This object represents BSSID of the station detected during a rogue scan.

OBJECT-TYPE

This table is used to configure a security profile. A security profile can consist of single or muliple security modes.

OBJECT-TYPE

This object represents an entry in the security profile table. This table is index by two indices - the first/primary index defines the security profile, the second index defines a single or multiple security policies per profile. The primary index is used in the wireless interface SSID table to specify which security profile to use per SSID. The admin/user can configure policies for different wireless station types by specifying a authentication and cipher mode/type. Below are examples of how to configure different STA types. STA Type Authentication Mode Cipher Mode ======== =================== =========== Non Secure None None WEP None WEP (64, 128, 152) 802.1x 802.1x WEP (64, 128) WPA 802.1x TKIP WPA-PSK PSK TKIP 802.11i 802.1x AES 802.11i-PSK PSK AES In the case of None, WEP, WPA-PSK, and 802.11i-PSK, MAC Access Control Table/List and RADIUS based MAC access control can be used to authenticate the wireless STA.

OBJECT-TYPE

This object represents the primary index of the Security Policy Table. This index is used to specify which security policy will be used per SSID, in the Wireless Interface SSID Table. A security policy can consist of a single or multiple security modes.

OBJECT-TYPE

This object is the secondary index to the Security Policy Table. This index will represent the different security modes per security profile.

OBJECT-TYPE

This object is used to specify the authentication mode for the security mode.

OBJECT-TYPE

This object is used to specify the cipher mode/type for the security mode.

OBJECT-TYPE

This object represents Encryption Key 0. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents Encryption Key 1. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents Encryption Key 2. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents Encryption Key 3. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object indicates which encryption key is used to encrypt data that is sent via the wireless interfaces. The default value for this object should be key 0.

OBJECT-TYPE

This object represents the encryption key length, the supported key lengths are 64 bits (40 + 24 for IV), 128 bits (104 + 24 for IV), and 152 bits (128 + 24 for IV).

OBJECT-TYPE

The Pre-Shared Key (PSK) for when RSN in PSK mode is the selected authentication suite. In that case, the PMK will obtain its value from this object. This object is logically write-only. Reading this variable shall return unsuccessful status or null or zero.

OBJECT-TYPE

The PSK, for when RSN in PSK mode is the selected authentication suite, is configured by oriWirelessIfSSIDTablePSKValue. An alternative manner of setting the PSK uses the password-to-key algorithm defined in the standard. This variable provides a means to enter a pass phrase. When this object is written, the RSN entity shall use the password-to-key algorithm specified in the standard to derive a pre-shared and populate oriWirelessIfSSIDTablePSKValue with this key. This object is logically write-only. Reading this variable shall return unsuccessful status or null or zero.

OBJECT-TYPE

This object represents the Table row status.

OBJECT-TYPE

This object is used to configure the security profile to use with four WEP keys. Currently only one security profile can be active which supports four WEP keys. Therefore this object is used to specify which profile will be using four WEP keys. The purpose of this object is to support legacy products/users that are still using four WEP keys.

OBJECT-IDENTITY

OBJECT-TYPE

This object allows to enable or disable the PPPoE service in the device.

OBJECT-TYPE

This object represents the maximum number of PPPoE sessions.

OBJECT-TYPE

This object represents the number of active PPPoE sessions.

OBJECT-TYPE

This table is used to configure the PPPoE session information.

OBJECT-TYPE

This object represents an entry in the PPPoE session table.

OBJECT-TYPE

This object is used as the index to the PPPoE Session Table.

OBJECT-TYPE

This object represents the WAN connect mode.

OBJECT-TYPE

This object is used as a timeout for the PPPoE session to be disconnected from public side if idle for specified amount of time.

OBJECT-TYPE

This object identifies the PPPoE session connect time.

OBJECT-TYPE

This object represents the maximum connection time per session.

OBJECT-TYPE

This object represents the time in seconds between PADI retries from the Host.

OBJECT-TYPE

This object represents the number of times the Host sends a PADI.

OBJECT-TYPE

This object represents the number of PPPoE PADI transmitted.

OBJECT-TYPE

This object represents the number of PPPoE PADT transmitted.

OBJECT-TYPE

This object represents the number of PPPoE Service-Name-Error tags received/transmitted.

OBJECT-TYPE

This object represents the number of PPPoE AC-System-Error tags received/transmitted.

OBJECT-TYPE

This object represents the number of PPPoE Generic-Error tags received.

OBJECT-TYPE

This object represents the number of PPPoE Generic Error tags transmitted.

OBJECT-TYPE

This object represents teh number of malformed PPPoE packets received.

OBJECT-TYPE

This object represents the number of PPPoE multiple PADO's received after a PADI request.

OBJECT-TYPE

This object represents the PPPoE user name.

OBJECT-TYPE

This object represents the PPPoE user name password. This object should be treated as write-only and returned as asterisks.

OBJECT-TYPE

This object represents the PPPoE service name.

OBJECT-TYPE

This object represents the PPPoE ISP name.

OBJECT-TYPE

This object represents the PPPoE ISP table entry status.

OBJECT-TYPE

This object is used to connect of disconnect the PPPoE session when the connect mode is set to manual.

OBJECT-TYPE

This object represents the state of the PPPoE WAN connection interface.

OBJECT-TYPE

This table is used to map client MAC address to PPPoE Session information for an ISP.

OBJECT-TYPE

This object represents an entry in the PPPoE MAC to Session table.

OBJECT-TYPE

This object is used as the index to the PPPoE Session Table.

OBJECT-TYPE

This object represents the client MAC address.

OBJECT-TYPE

This object represents the ISP name.

OBJECT-TYPE

This object represents the PPPoE MAC to Session table entry status.

OBJECT-IDENTITY

OBJECT-TYPE

This object represents the quickstart modes that the device can be configured in.

OBJECT-TYPE

This table contains the current configuration files stored in the device. This table is used to manage the different configuration files.

OBJECT-TYPE

This object represents an entry in the configuration file table.

OBJECT-TYPE

This object represents the index to the configuration file table.

OBJECT-TYPE

This object represents the configuration file name.

OBJECT-TYPE

This object represents the status of the configuration file. The possible options are: - Enable: active configuration file - Disable: inactive configuration file - Delete: in order to delete the configuration file

OBJECT-TYPE

This object saves the configuration to the specified name.

OBJECT-TYPE

This object is used to identify the last know good configuration file used. Setting a value of 1 to this objecgt saves the current configuration as the known good configuration.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the DNS Redirect functionality.

OBJECT-TYPE

This object represents the maximum response wait time for DNS redirect. The units for this object is seconds.

OBJECT-TYPE

This object represents the Primary DNS IP Address.

OBJECT-TYPE

This object represents the Secondary DNS IP Address.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the DNS Client feature.

OBJECT-TYPE

This object represents the Primary Server DNS IP Address.

OBJECT-TYPE

This object represents the Secondary Server DNS IP Address.

OBJECT-TYPE

This object represents the default domain name for the DNS Client.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable/disable the AOL NAT Application Level Gateway (ALG) support.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable/disable the NAT feature.

OBJECT-TYPE

A Bit Mask documenting the NAT device's actual configuration according to natTypeMask above. Its value may be one and only one of the options below: - Basic-NAT (Bit 0) - NAPT (Bit 1) - Bi-directional-NAT (Bit 2) - Twice-NAT (Bit 3) - RSA-IP-Server (Bit 4) - RSAP-IP-Server (Bit 5) - Bit 0, if set, indicates that Basic-NAT is configured. - Bit 1, if set, indicates that NAPT is configured. - Bit 2, if set, indicates that Bi-directional-NAT is configured. - Bit 3, if set, indicates that Twice-NAT is configured. - Bit 4, if set, indicates that RSA-IP-Server is configured. - Bit 5, if set, indicates that RSAP-IP-Server is configured.

OBJECT-TYPE

This object is used to enable or disable static bind entries on the NAT device.

OBJECT-TYPE

This object is used to provide information on the NAT public IP Address.

OBJECT-TYPE

This table contains NAT IP bind specific information.

OBJECT-TYPE

This object is an entry in the NAT Static IP Bind Table.

OBJECT-TYPE

This object is used as the index for the NAT static IP bind table.

OBJECT-TYPE

This object represents the local IP address for this NAT Static IP bind Table entry.

OBJECT-TYPE

This object represents the remote IP address for this NAT Static IP bind Table entry.

OBJECT-TYPE

The object indicates the status of the NAT Static IP Bind Table entry.

OBJECT-TYPE

This table is used to configure NAT Port bind specific information.

OBJECT-TYPE

This object represents an entry in the NAT Static Port Bind Table.

OBJECT-TYPE

This object is used as the index for the NAT static Port bind table.

OBJECT-TYPE

This object represents the local IP address for this NAT Static Port bind Table entry.

OBJECT-TYPE

This object represents the start port number for this NAT Static Port bind Table entry.

OBJECT-TYPE

This object represents the end port number for this NAT Static Port bind Table entry.

OBJECT-TYPE

This object represents the port type for this NAT Static Port bind Table entry.

OBJECT-TYPE

The object indicates the status of the NAT Static Port Bind Table entry.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the SpectraLink VoIP feature.

OBJECT-TYPE

This object is used to enable/disable SpectraLink VoIP support for legacy SpectraLink devices/phones.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the VLAN feature.

OBJECT-TYPE

This object represents the VLAN management Identifier (ID).

OBJECT-TYPE

This table is used to configure the VLAN IDs for the device. This table has been deprecated.

OBJECT-TYPE

This object represents an entry in the respective table. In this case each table entry represents a VLAN ID. This object has been deprecated.

OBJECT-TYPE

This object represents the index to the VLAN ID Table. This object has been deprecated.

OBJECT-TYPE

This object represents the VLAN Identifier (ID). This object has been deprecated.

OBJECT-IDENTITY

OBJECT-TYPE

A table containing DMZ host IP information. Only if the system is in Gateway mode, and the NAT is enabled, and this table has valid 'enabled' entry, the DMZ takes effect.

OBJECT-TYPE

This object represents an entry in the DMZ host IP Table.

OBJECT-TYPE

This object is used as the index for the DMZ host IP Table.

OBJECT-TYPE

This object represents the DMZ host IP address.

OBJECT-TYPE

This objecgt is used for an optional comment associated to the DMZ host IP Table entry.

OBJECT-TYPE

The object indicates the status of the DMZ host IP Table entry.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to specify the OEM name.

OBJECT-TYPE

This object is used to specify the OEM home URL.

OBJECT-TYPE

This object represents the product name. It is the same name as shown in all management Web pages.

OBJECT-TYPE

This object represents the product model.

OBJECT-TYPE

This object represents the name of logo image file.

OBJECT-TYPE

This object represents the name of no nav. logo image file.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains wireless stations statistics.

OBJECT-TYPE

This object represents an entry in the respective table. In this case each table entry represents a wireless station.

OBJECT-TYPE

This object represents the index of the stations statistics table. This table is limited to 500 entries.

OBJECT-TYPE

This object represents the MAC address of the station for which the statistics are gathered.

OBJECT-TYPE

This object represents the IP address of the stations for which the statistics are gathered. If the IP address is not known, 0.0.0.0 will be returned.

OBJECT-TYPE

This object represents the number of the interface on which the station is last seen.

OBJECT-TYPE

This object represents the name of the station. If the name is not known, an empty string will be returned.

OBJECT-TYPE

This object represents the type of station.

OBJECT-TYPE

This object represents the MAC protocol for this station.

OBJECT-TYPE

This object represents the administrative state for the station. The testing(3) state indicates that no operational packets can be passed.

OBJECT-TYPE

This object represents the current operational state of the interface. The testing(3) state indicates that no operational packets can be passed.

OBJECT-TYPE

This object represents the value of sysUpTime at the time the station entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value.

OBJECT-TYPE

This object represents the last state of this station.

OBJECT-TYPE

The total number of octets received from the station, including framing characters.

OBJECT-TYPE

This object represents the number of unicast packets from the station that are further processed by either by the bridge/router or by the internal host.

OBJECT-TYPE

This object represents the number of non-unicast packets (i.e. broadcast or multicast) from the station that are further processed by either by the bridge/router or by the internal host.

OBJECT-TYPE

This object represents the number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to the internal bridge/router or the internal host. One possible reason for discarding such a packet could be to lack of buffer space.

OBJECT-TYPE

This object represents the total number of octets send to the station, including framing characters.

OBJECT-TYPE

This object represents the number of packets that the internal bridge/router or the internal host requested be transmitted to the station, including those that were discarded or not sent.

OBJECT-TYPE

This object represents the number of packets that the internal bridge/router or the internal host requested be transmitted to a non-unicast (i.e. broadcast or multicast) address that includes the station. This counter includes those packets that were discarded or not sent.

OBJECT-TYPE

This object represents the number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to the internal bridge/router or the internal host. One possible reason for discarding such a packet could be to lack of buffer space.

OBJECT-TYPE

This object represents the current signal level calculated over the inbound packets from this station. This variable indicates the running average of the local signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

This object represents the current noise level calculated over the inbound packets from this station. This variable indicates the running average of the local noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

This object represents the current remote signal level calculated over the inbound packets from this station on the remote station. This variable indicates the running average of the remote signal level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

This object represents the current remote noise level calculated over the inbound packets from this station on the remote station. This variable indicates the running average of the remote noise level using the algorithm (3/4*oldvalue + 1/4*newvalue).

OBJECT-TYPE

This object represents the value of sysUpTime at the time the last packet from the remote station was received.

OBJECT-TYPE

This object is used to enable or disable the monitoring of the wireless station statistics.

OBJECT-TYPE

This object represents the number of active wireless clients associated to the access point.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used to enable or disable the SNTP functionality.

OBJECT-TYPE

This object represents the primary SNTP server IP address or host name.

OBJECT-TYPE

This object represents the secondary SNTP server IP address or host name.

OBJECT-TYPE

This parameter is used for the device to know how to adjust GMT for local time.

OBJECT-TYPE

This object represents the Date and Time. The format of this object is the same as the DateAndTime textual convention.

OBJECT-TYPE

This parameter indicates the number of hours to adjust for Daylight Saving Time.

OBJECT-TYPE

This object represents the year. This object can be used to manually configure the year in case the Date and Time is not retrieved from an SNTP server.

OBJECT-TYPE

This object represents the month. This object can be used to manually configure the month in case the Date and Time is not retrieved from an SNTP server.

OBJECT-TYPE

This object represents the day of the month. This object can be used to manually configure the year in case the Date and Time is not retrieved from an SNTP server.

OBJECT-TYPE

This object represents the hour of day. This object can be used to manually configure the hour in case the Date and Time is not retrieved from an SNTP server.

OBJECT-TYPE

This object represents the minutes. This object can be used to manually configure the minutes in case the Date and Time is not retrieved from an SNTP server.

OBJECT-TYPE

This object represents the number of seconds. This object can be used to manually configure the seconds in case the Date and Time is not retrieved from an SNTP server.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY