MIBs Depot

OPT-IF-MIB

Registered at
1.3.6.1.2.1.10.133
Last updated
2003-08-13 00:00
Organization
IETF AToM MIB Working Group
Revisions
2003-08-13 00:00
Namespace
standard
Source file
OPT-IF-MIB
Digest
sha256:03054f8c7605311b078042a0fc94282fed56d2105822844515d464d550610654

Description

The MIB module to describe pre-OTN and OTN interfaces. Copyright (C) The Internet Society (2003). This version of this MIB module is part of RFC 3591; see the RFC itself for full legal notices.

Contact

WG charter: http://www.ietf.org/html.charters/atommib-charter.html Mailing Lists: General Discussion: atommib@research.telcordia.com To Subscribe: atommib-request@research.telcordia.com Editor: Hing-Kam Lam Postal: Lucent Technologies, Room 4C-616 101 Crawfords Corner Road Holmdel, NJ 07733 Tel: +1 732 949 8338 Email: hklam@lucent.com

Imports

FromSymbols
IF-MIBifIndex
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIGauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso, transmission
SNMPv2-TCDisplayString, RowPointer, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

IANAifType-MIB
IF-MIB
OPT-IF-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
OptIfAcTI
TEXTUAL-CONVENTION
The trace identifier (TI) accepted at the receiver.
current
OptIfBitRateK
TEXTUAL-CONVENTION
Indicates the index 'k' that is used to represent a supported bit rate and the different versions of OPUk, ODUk and OTUk. Allowed values of k are defined in ITU-T G.709. Currently allowed values in G.709 are: k=1 represents an approximate bit rate of 2.5 Gbit/s, k=2 represents an approximate bit rate of 10 Gbit/s, k=3 represents an approximate bit rate of 40 Gbit/s.
current
OptIfDEGM
TEXTUAL-CONVENTION
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if OptIfDEGM consecutive bad PM Seconds are detected.
current
OptIfDEGThr
TEXTUAL-CONVENTION
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to OptIfDEGThr.
current
OptIfDirectionality
TEXTUAL-CONVENTION
Indicates the directionality of an entity.
current
OptIfExDAPI
TEXTUAL-CONVENTION
The Destination Access Point Identifier (DAPI) expected by the receiver.
current
OptIfExSAPI
TEXTUAL-CONVENTION
The Source Access Point Identifier (SAPI) expected by the receiver.
current
OptIfIntervalNumber
TEXTUAL-CONVENTION
Uniquely identifies a 15-minute interval. The interval identified by 1 is the most recently completed interval, and the interval identified by n is the interval immediately preceding the one identified by n-1.
current
OptIfSinkOrSource
TEXTUAL-CONVENTION
Indicates the directionality of an entity that is allowed only to be a source or sink.
current
OptIfTIMDetMode
TEXTUAL-CONVENTION
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
current
OptIfTxTI
TEXTUAL-CONVENTION
The trace identifier (TI) transmitted.
current

Objects

NameOIDSyntaxAccessStatus
optIfObjects
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1
optIfOTMn
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.1
optIfOTMnTable
OBJECT-TYPE
A table of OTMn structure information.
1.3.6.1.2.1.10.133.1.1.1not-accessiblecurrent
optIfOTMnEntry
OBJECT-TYPE
A conceptual row that contains the OTMn structure information of an optical interface.
1.3.6.1.2.1.10.133.1.1.1.1not-accessiblecurrent
optIfOTMnOrder
OBJECT-TYPE
This object indicates the order of the OTM, which represents the maximum number of wavelengths that can be supported at the bit rate(s) supported on the interface.
1.3.6.1.2.1.10.133.1.1.1.1.1Unsigned32 (1..900)read-onlycurrent
optIfOTMnReduced
OBJECT-TYPE
This object indicates whether a reduced or full functionality is supported at the interface. A value of true means reduced. A value of false means full.
1.3.6.1.2.1.10.133.1.1.1.1.2TruthValueread-onlycurrent
optIfOTMnBitRates
OBJECT-TYPE
This attribute is a bit map representing the bit rate or set of bit rates supported on the interface. The meaning of each bit position is as follows: bitRateK1(0) is set if the 2.5 Gbit/s rate is supported bitRateK2(1) is set if the 10 Gbit/s rate is supported bitRateK3(2) is set if the 40 Gbit/s rate is supported Note that each bit position corresponds to one possible value of the type OptIfBitRateK. The default value of this attribute is system specific.
1.3.6.1.2.1.10.133.1.1.1.1.3Bits {bitRateK1(0), bitRateK2(1), bitRateK3(2)}read-onlycurrent
optIfOTMnInterfaceType
OBJECT-TYPE
This object identifies the type of interface. The value of this attribute will affect the behavior of the OTM with respect to presence/absence of OTM Overhead Signal (OOS) processing and TCM activation. For an IrDI interface, there is no OOS processing and TCM activation is limited to n levels as specified by a TCM level threshold. This object contains two fields that are separated by whitespace. The possible values are: field 1: one of the 4-character ASCII strings 'IrDI' or 'IaDI' field 2: free-form text consisting of printable UTF-8 encoded characters Note that field 2 is optional. If it is not present then there is no requirement for trailing whitespace after field 1. The default values are as follows: field 1: 'IaDI' field 2: an empty string.
1.3.6.1.2.1.10.133.1.1.1.1.4SnmpAdminStringread-onlycurrent
optIfOTMnTcmMax
OBJECT-TYPE
This object identifies the maximum number of TCM levels allowed for any Optical Channel contained in this OTM. A new TCM activation will be rejected if the requested level is greater than the threshold. If InterfaceType object specifies a type of 'IaDI' for this OTM, then this attribute is irrelevant. Possible values: unsigned integers in the range from 0 to 6 inclusive. Default value: 3.
1.3.6.1.2.1.10.133.1.1.1.1.5Unsigned32 (0..6)read-writecurrent
optIfOTMnOpticalReach
OBJECT-TYPE
This object indicates the length the optical signal may travel before requiring termination or regeneration. The meaning of the enumeration are: intraOffice(1) - intra-office (as defined in ITU-T G.957) shortHaul(2) - short haul (as defined in ITU-T G.957) longHaul(3) - long haul (as defined in ITU-T G.957) veryLongHaul(4) - very long haul (as defined in ITU-T G.691) ultraLongHaul(5)- ultra long haul (as defined in ITU-T G.691)
1.3.6.1.2.1.10.133.1.1.1.1.6INTEGER {intraOffice(1), shortHaul(2), longHaul(3), veryLongHaul(4), ultraLongHaul(5)}read-onlycurrent
optIfPerfMon
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.2
optIfPerfMonIntervalTable
OBJECT-TYPE
A table of 15-minute performance monitoring interval information.
1.3.6.1.2.1.10.133.1.2.1not-accessiblecurrent
optIfPerfMonIntervalEntry
OBJECT-TYPE
A conceptual row that contains 15-minute performance monitoring interval information of an interface.
1.3.6.1.2.1.10.133.1.2.1.1not-accessiblecurrent
optIfPerfMonCurrentTimeElapsed
OBJECT-TYPE
Number of seconds elapsed in the current 15-minute performance monitoring interval. If, for some reason, such as an adjustment in the NE's time-of-day clock, the number of seconds elapsed exceeds the maximum value, then the maximum value will be returned.
1.3.6.1.2.1.10.133.1.2.1.1.1Gauge32 (0..900)read-onlycurrent
optIfPerfMonCurDayTimeElapsed
OBJECT-TYPE
Number of seconds elapsed in the current 24-hour interval performance monitoring period. If, for some reason, such as an adjustment in the NE's time-of-day clock, the number of seconds elapsed exceeds the maximum value, then the maximum value will be returned.
1.3.6.1.2.1.10.133.1.2.1.1.2Gauge32 (0..86400)read-onlycurrent
optIfPerfMonIntervalNumIntervals
OBJECT-TYPE
The number of 15-minute intervals for which performance monitoring data is available. The number is the same for all the associated sub layers of the interface. An optical interface must be capable of supporting at least n intervals, where n is defined as follows: The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value of this object will be n unless performance monitoring was (re-)started for the interface within the last (n*15) minutes, in which case the value will be the number of complete 15-minute intervals since measurement was (re-)started.
1.3.6.1.2.1.10.133.1.2.1.1.3Unsigned32 (0..96)read-onlycurrent
optIfPerfMonIntervalNumInvalidIntervals
OBJECT-TYPE
The number of intervals in the range from 0 to optIfPerfMonIntervalNumIntervals for which no performance monitoring data is available and/or the data is invalid.
1.3.6.1.2.1.10.133.1.2.1.1.4Unsigned32 (0..96)read-onlycurrent
optIfOTSn
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.3
optIfOTSnConfigTable
OBJECT-TYPE
A table of OTSn configuration information.
1.3.6.1.2.1.10.133.1.3.1not-accessiblecurrent
optIfOTSnConfigEntry
OBJECT-TYPE
A conceptual row that contains OTSn configuration information of an interface.
1.3.6.1.2.1.10.133.1.3.1.1not-accessiblecurrent
optIfOTSnDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.2.1.10.133.1.3.1.1.1OptIfDirectionalityread-onlycurrent
optIfOTSnAprStatus
OBJECT-TYPE
This attribute indicates the status of the Automatic Power Reduction (APR) function of the entity. Valid values are 'on' and 'off'.
1.3.6.1.2.1.10.133.1.3.1.1.2SnmpAdminStringread-onlycurrent
optIfOTSnAprControl
OBJECT-TYPE
This object is a UTF-8 encoded string that specifies Automatic Power Reduction (APR) control actions requested of this entity (when written) and that returns the current APR control state of this entity (when read). The values are implementation-defined. Any implementation that instantiates this object must document the set of values that it allows to be written, the set of values that it will return, and what each of those values means.
1.3.6.1.2.1.10.133.1.3.1.1.3SnmpAdminStringread-writecurrent
optIfOTSnTraceIdentifierTransmitted
OBJECT-TYPE
The trace identifier transmitted. This object is applicable when optIfOTSnDirectionality has the value source(2) or bidirectional(3). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI'). If no value is ever set by a management entity for the object optIfOTSnTraceIdentifierTransmitted, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
1.3.6.1.2.1.10.133.1.3.1.1.4OptIfTxTIread-writecurrent
optIfOTSnDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect if optIfOTSnTIMDetMode has the value off(1) or sapi(3). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI').
1.3.6.1.2.1.10.133.1.3.1.1.5OptIfExDAPIread-writecurrent
optIfOTSnSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect if optIfOTSnTIMDetMode has the value off(1) or dapi(2). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI').
1.3.6.1.2.1.10.133.1.3.1.1.6OptIfExSAPIread-writecurrent
optIfOTSnTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier received. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). Its value is unspecified if optIfOTSnCurrentStatus has either or both of the losO(5) and los(6) bits set. This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI').
1.3.6.1.2.1.10.133.1.3.1.1.7OptIfAcTIread-onlycurrent
optIfOTSnTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). The default value is off(1). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI'). The default value of this object is off(1).
1.3.6.1.2.1.10.133.1.3.1.1.8OptIfTIMDetModeread-writecurrent
optIfOTSnTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). It has no effect when the value of optIfOTSnTIMDetMode is off(1). This object does not apply to reduced-capability systems (i.e., those for which optIfOTMnReduced has the value true(1)) or at IrDI interfaces (i.e., when optIfOTMnInterfaceType field 1 has the value 'IrDI'). The default value of this object is false(2).
1.3.6.1.2.1.10.133.1.3.1.1.9TruthValueread-writecurrent
optIfOTSnCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is applicable when optIfOTSnDirectionality has the value sink(1) or bidirectional(3). In reduced-capability systems or at IrDI interfaces the only bit position that may be set is los(6).
1.3.6.1.2.1.10.133.1.3.1.1.10Bits {bdiP(0), bdiO(1), bdi(2), tim(3), losP(4), losO(5), los(6)}read-onlycurrent
optIfOTSnSinkCurrentTable
OBJECT-TYPE
A table of OTSn sink performance monitoring information for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.2not-accessiblecurrent
optIfOTSnSinkCurrentEntry
OBJECT-TYPE
A conceptual row that contains OTSn sink performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.2.1not-accessiblecurrent
optIfOTSnSinkCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.3.2.1.1TruthValueread-onlycurrent
optIfOTSnSinkCurrentInputPower
OBJECT-TYPE
The optical power monitored at the input.
1.3.6.1.2.1.10.133.1.3.2.1.2Integer32read-onlycurrent
optIfOTSnSinkCurrentLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.2.1.3Integer32read-onlycurrent
optIfOTSnSinkCurrentHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.2.1.4Integer32read-onlycurrent
optIfOTSnSinkCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on input power. If optIfOTSnSinkCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.3.2.1.5Integer32read-writecurrent
optIfOTSnSinkCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on input power. If optIfOTSnSinkCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.3.2.1.6Integer32read-writecurrent
optIfOTSnSinkCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.2.1.10.133.1.3.2.1.7Integer32read-onlycurrent
optIfOTSnSinkCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.2.1.8Integer32read-onlycurrent
optIfOTSnSinkCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.2.1.9Integer32read-onlycurrent
optIfOTSnSinkCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If optIfOTSnSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.3.2.1.10Integer32read-writecurrent
optIfOTSnSinkCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If optIfOTSnSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.3.2.1.11Integer32read-writecurrent
optIfOTSnSinkIntervalTable
OBJECT-TYPE
A table of historical OTSn sink performance monitoring information.
1.3.6.1.2.1.10.133.1.3.3not-accessiblecurrent
optIfOTSnSinkIntervalEntry
OBJECT-TYPE
A conceptual row that contains OTSn sink performance monitoring information of an interface during a particular historical interval.
1.3.6.1.2.1.10.133.1.3.3.1not-accessiblecurrent
optIfOTSnSinkIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.2.1.10.133.1.3.3.1.1OptIfIntervalNumbernot-accessiblecurrent
optIfOTSnSinkIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.3.3.1.2TruthValueread-onlycurrent
optIfOTSnSinkIntervalLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.3.3.1.3Integer32read-onlycurrent
optIfOTSnSinkIntervalLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.3.3.1.4Integer32read-onlycurrent
optIfOTSnSinkIntervalHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.3.3.1.5Integer32read-onlycurrent
optIfOTSnSinkIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.3.3.1.6Integer32read-onlycurrent
optIfOTSnSinkIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.3.3.1.7Integer32read-onlycurrent
optIfOTSnSinkIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.3.3.1.8Integer32read-onlycurrent
optIfOTSnSinkCurDayTable
OBJECT-TYPE
A table of OTSn sink performance monitoring information for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.4not-accessiblecurrent
optIfOTSnSinkCurDayEntry
OBJECT-TYPE
A conceptual row that contains OTSn sink performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.4.1not-accessiblecurrent
optIfOTSnSinkCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.3.4.1.1TruthValueread-onlycurrent
optIfOTSnSinkCurDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.4.1.2Integer32read-onlycurrent
optIfOTSnSinkCurDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.4.1.3Integer32read-onlycurrent
optIfOTSnSinkCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.4.1.4Integer32read-onlycurrent
optIfOTSnSinkCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.4.1.5Integer32read-onlycurrent
optIfOTSnSinkPrevDayTable
OBJECT-TYPE
A table of OTSn sink performance monitoring information for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.5not-accessiblecurrent
optIfOTSnSinkPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OTSn sink performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.5.1not-accessiblecurrent
optIfOTSnSinkPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.3.5.1.1TruthValueread-onlycurrent
optIfOTSnSinkPrevDayLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.5.1.2Integer32read-onlycurrent
optIfOTSnSinkPrevDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.5.1.3Integer32read-onlycurrent
optIfOTSnSinkPrevDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.5.1.4Integer32read-onlycurrent
optIfOTSnSinkPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.5.1.5Integer32read-onlycurrent
optIfOTSnSinkPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.5.1.6Integer32read-onlycurrent
optIfOTSnSinkPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.5.1.7Integer32read-onlycurrent
optIfOTSnSrcCurrentTable
OBJECT-TYPE
A table of OTSn source performance monitoring information for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.6not-accessiblecurrent
optIfOTSnSrcCurrentEntry
OBJECT-TYPE
A conceptual row that contains OTSn source performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.6.1not-accessiblecurrent
optIfOTSnSrcCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.3.6.1.1TruthValueread-onlycurrent
optIfOTSnSrcCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.2.1.10.133.1.3.6.1.2Integer32read-onlycurrent
optIfOTSnSrcCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.6.1.3Integer32read-onlycurrent
optIfOTSnSrcCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.6.1.4Integer32read-onlycurrent
optIfOTSnSrcCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If optIfOTSnSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.3.6.1.5Integer32read-writecurrent
optIfOTSnSrcCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If optIfOTSnSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.3.6.1.6Integer32read-writecurrent
optIfOTSnSrcCurrentInputPower
OBJECT-TYPE
The optical power monitored at the input.
1.3.6.1.2.1.10.133.1.3.6.1.7Integer32read-onlycurrent
optIfOTSnSrcCurrentLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.6.1.8Integer32read-onlycurrent
optIfOTSnSrcCurrentHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.3.6.1.9Integer32read-onlycurrent
optIfOTSnSrcCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on input power. If optIfOTSnSrcCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.3.6.1.10Integer32read-writecurrent
optIfOTSnSrcCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on input power. If optIfOTSnSrcCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.3.6.1.11Integer32read-writecurrent
optIfOTSnSrcIntervalTable
OBJECT-TYPE
A table of historical OTSn source performance monitoring information.
1.3.6.1.2.1.10.133.1.3.7not-accessiblecurrent
optIfOTSnSrcIntervalEntry
OBJECT-TYPE
A conceptual row that contains OTSn source performance monitoring information of an interface during a particular historical interval.
1.3.6.1.2.1.10.133.1.3.7.1not-accessiblecurrent
optIfOTSnSrcIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.2.1.10.133.1.3.7.1.1OptIfIntervalNumbernot-accessiblecurrent
optIfOTSnSrcIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.3.7.1.2TruthValueread-onlycurrent
optIfOTSnSrcIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.3.7.1.3Integer32read-onlycurrent
optIfOTSnSrcIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.3.7.1.4Integer32read-onlycurrent
optIfOTSnSrcIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.3.7.1.5Integer32read-onlycurrent
optIfOTSnSrcIntervalLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.3.7.1.6Integer32read-onlycurrent
optIfOTSnSrcIntervalLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.3.7.1.7Integer32read-onlycurrent
optIfOTSnSrcIntervalHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.3.7.1.8Integer32read-onlycurrent
optIfOTSnSrcCurDayTable
OBJECT-TYPE
A table of OTSn source performance monitoring information for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.8not-accessiblecurrent
optIfOTSnSrcCurDayEntry
OBJECT-TYPE
A conceptual row that contains OTSn source performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.8.1not-accessiblecurrent
optIfOTSnSrcCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.3.8.1.1TruthValueread-onlycurrent
optIfOTSnSrcCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.8.1.2Integer32read-onlycurrent
optIfOTSnSrcCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.8.1.3Integer32read-onlycurrent
optIfOTSnSrcCurDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.8.1.4Integer32read-onlycurrent
optIfOTSnSrcCurDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.3.8.1.5Integer32read-onlycurrent
optIfOTSnSrcPrevDayTable
OBJECT-TYPE
A table of OTSn source performance monitoring information for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.9not-accessiblecurrent
optIfOTSnSrcPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OTSn source performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.9.1not-accessiblecurrent
optIfOTSnSrcPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.3.9.1.1TruthValueread-onlycurrent
optIfOTSnSrcPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.9.1.2Integer32read-onlycurrent
optIfOTSnSrcPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.9.1.3Integer32read-onlycurrent
optIfOTSnSrcPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.9.1.4Integer32read-onlycurrent
optIfOTSnSrcPrevDayLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.9.1.5Integer32read-onlycurrent
optIfOTSnSrcPrevDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.9.1.6Integer32read-onlycurrent
optIfOTSnSrcPrevDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.3.9.1.7Integer32read-onlycurrent
optIfOMSn
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.4
optIfOMSnConfigTable
OBJECT-TYPE
A table of OMSn configuration information.
1.3.6.1.2.1.10.133.1.4.1not-accessiblecurrent
optIfOMSnConfigEntry
OBJECT-TYPE
A conceptual row that contains OMSn configuration information of an interface.
1.3.6.1.2.1.10.133.1.4.1.1not-accessiblecurrent
optIfOMSnDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.2.1.10.133.1.4.1.1.1OptIfDirectionalityread-onlycurrent
optIfOMSnCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is applicable only to full capability systems whose interface type is IaDI and for which optIfOMSnDirectionality has the value sink(1) or bidirectional(3).
1.3.6.1.2.1.10.133.1.4.1.1.2Bits {ssfP(0), ssfO(1), ssf(2), bdiP(3), bdiO(4), bdi(5), losP(6)}read-onlycurrent
optIfOMSnSinkCurrentTable
OBJECT-TYPE
A table of OMSn sink performance monitoring information for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.2not-accessiblecurrent
optIfOMSnSinkCurrentEntry
OBJECT-TYPE
A conceptual row that contains OMSn sink performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.2.1not-accessiblecurrent
optIfOMSnSinkCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.4.2.1.1TruthValueread-onlycurrent
optIfOMSnSinkCurrentAggregatedInputPower
OBJECT-TYPE
The aggregated optical power of all the DWDM input channels.
1.3.6.1.2.1.10.133.1.4.2.1.2Integer32read-onlycurrent
optIfOMSnSinkCurrentLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.2.1.3Integer32read-onlycurrent
optIfOMSnSinkCurrentHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.2.1.4Integer32read-onlycurrent
optIfOMSnSinkCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on aggregated input power. If optIfOMSnSinkCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.4.2.1.5Integer32read-writecurrent
optIfOMSnSinkCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on aggregated input power. If optIfOMSnSinkCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.4.2.1.6Integer32read-writecurrent
optIfOMSnSinkCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.2.1.10.133.1.4.2.1.7Integer32read-onlycurrent
optIfOMSnSinkCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.2.1.8Integer32read-onlycurrent
optIfOMSnSinkCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.2.1.9Integer32read-onlycurrent
optIfOMSnSinkCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If optIfOMSnSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.4.2.1.10Integer32read-writecurrent
optIfOMSnSinkCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If optIfOMSnSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.4.2.1.11Integer32read-writecurrent
optIfOMSnSinkIntervalTable
OBJECT-TYPE
A table of historical OMSn sink performance monitoring information.
1.3.6.1.2.1.10.133.1.4.3not-accessiblecurrent
optIfOMSnSinkIntervalEntry
OBJECT-TYPE
A conceptual row that contains OMSn sink performance monitoring information of an interface during a particular historical interval.
1.3.6.1.2.1.10.133.1.4.3.1not-accessiblecurrent
optIfOMSnSinkIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.2.1.10.133.1.4.3.1.1OptIfIntervalNumbernot-accessiblecurrent
optIfOMSnSinkIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.4.3.1.2TruthValueread-onlycurrent
optIfOMSnSinkIntervalLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power of all the DWDM input channels during the interval.
1.3.6.1.2.1.10.133.1.4.3.1.3Integer32read-onlycurrent
optIfOMSnSinkIntervalLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels during the interval.
1.3.6.1.2.1.10.133.1.4.3.1.4Integer32read-onlycurrent
optIfOMSnSinkIntervalHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels during the interval.
1.3.6.1.2.1.10.133.1.4.3.1.5Integer32read-onlycurrent
optIfOMSnSinkIntervalLastOutputPower
OBJECT-TYPE
The last optical power at the output during the interval.
1.3.6.1.2.1.10.133.1.4.3.1.6Integer32read-onlycurrent
optIfOMSnSinkIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power at the output during the interval.
1.3.6.1.2.1.10.133.1.4.3.1.7Integer32read-onlycurrent
optIfOMSnSinkIntervalHighOutputPower
OBJECT-TYPE
The highest optical power at the output during the interval.
1.3.6.1.2.1.10.133.1.4.3.1.8Integer32read-onlycurrent
optIfOMSnSinkCurDayTable
OBJECT-TYPE
A table of OMSn sink performance monitoring information for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.4not-accessiblecurrent
optIfOMSnSinkCurDayEntry
OBJECT-TYPE
A conceptual row that contains OMSn sink performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.4.1not-accessiblecurrent
optIfOMSnSinkCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.4.4.1.1TruthValueread-onlycurrent
optIfOMSnSinkCurDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.4.1.2Integer32read-onlycurrent
optIfOMSnSinkCurDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.4.1.3Integer32read-onlycurrent
optIfOMSnSinkCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.4.1.4Integer32read-onlycurrent
optIfOMSnSinkCurDayHighOutputPower
OBJECT-TYPE
The highest optical power at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.4.1.5Integer32read-onlycurrent
optIfOMSnSinkPrevDayTable
OBJECT-TYPE
A table of OMSn sink performance monitoring information for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.5not-accessiblecurrent
optIfOMSnSinkPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OMSn sink performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.5.1not-accessiblecurrent
optIfOMSnSinkPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.4.5.1.1TruthValueread-onlycurrent
optIfOMSnSinkPrevDayLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.5.1.2Integer32read-onlycurrent
optIfOMSnSinkPrevDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.5.1.3Integer32read-onlycurrent
optIfOMSnSinkPrevDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.5.1.4Integer32read-onlycurrent
optIfOMSnSinkPrevDayLastOutputPower
OBJECT-TYPE
The last optical power at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.5.1.5Integer32read-onlycurrent
optIfOMSnSinkPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.5.1.6Integer32read-onlycurrent
optIfOMSnSinkPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.5.1.7Integer32read-onlycurrent
optIfOMSnSrcCurrentTable
OBJECT-TYPE
A table of OMSn source performance monitoring information for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.6not-accessiblecurrent
optIfOMSnSrcCurrentEntry
OBJECT-TYPE
A conceptual row that contains OMSn source performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.6.1not-accessiblecurrent
optIfOMSnSrcCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.4.6.1.1TruthValueread-onlycurrent
optIfOMSnSrcCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.2.1.10.133.1.4.6.1.2Integer32read-onlycurrent
optIfOMSnSrcCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.6.1.3Integer32read-onlycurrent
optIfOMSnSrcCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.6.1.4Integer32read-onlycurrent
optIfOMSnSrcCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If optIfOMSnSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.4.6.1.5Integer32read-writecurrent
optIfOMSnSrcCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If optIfOMSnSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.4.6.1.6Integer32read-writecurrent
optIfOMSnSrcCurrentAggregatedInputPower
OBJECT-TYPE
The aggregated optical power at the input.
1.3.6.1.2.1.10.133.1.4.6.1.7Integer32read-onlycurrent
optIfOMSnSrcCurrentLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.6.1.8Integer32read-onlycurrent
optIfOMSnSrcCurrentHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.4.6.1.9Integer32read-onlycurrent
optIfOMSnSrcCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on aggregated input power. If optIfOMSnSrcCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.4.6.1.10Integer32read-writecurrent
optIfOMSnSrcCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on aggregated input power. If optIfOMSnSrcCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.4.6.1.11Integer32read-writecurrent
optIfOMSnSrcIntervalTable
OBJECT-TYPE
A table of historical OMSn source performance monitoring information.
1.3.6.1.2.1.10.133.1.4.7not-accessiblecurrent
optIfOMSnSrcIntervalEntry
OBJECT-TYPE
A conceptual row that contains OMSn source performance monitoring information of an interface during a particular historical interval.
1.3.6.1.2.1.10.133.1.4.7.1not-accessiblecurrent
optIfOMSnSrcIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.2.1.10.133.1.4.7.1.1OptIfIntervalNumbernot-accessiblecurrent
optIfOMSnSrcIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.4.7.1.2TruthValueread-onlycurrent
optIfOMSnSrcIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.4.7.1.3Integer32read-onlycurrent
optIfOMSnSrcIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.4.7.1.4Integer32read-onlycurrent
optIfOMSnSrcIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.4.7.1.5Integer32read-onlycurrent
optIfOMSnSrcIntervalLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power at the input during the interval.
1.3.6.1.2.1.10.133.1.4.7.1.6Integer32read-onlycurrent
optIfOMSnSrcIntervalLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power at the input during the interval.
1.3.6.1.2.1.10.133.1.4.7.1.7Integer32read-onlycurrent
optIfOMSnSrcIntervalHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power at the input during the interval.
1.3.6.1.2.1.10.133.1.4.7.1.8Integer32read-onlycurrent
optIfOMSnSrcCurDayTable
OBJECT-TYPE
A table of OMSn source performance monitoring information for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.8not-accessiblecurrent
optIfOMSnSrcCurDayEntry
OBJECT-TYPE
A conceptual row that contains OMSn source performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.8.1not-accessiblecurrent
optIfOMSnSrcCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.4.8.1.1TruthValueread-onlycurrent
optIfOMSnSrcCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.8.1.2Integer32read-onlycurrent
optIfOMSnSrcCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.8.1.3Integer32read-onlycurrent
optIfOMSnSrcCurDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.8.1.4Integer32read-onlycurrent
optIfOMSnSrcCurDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.4.8.1.5Integer32read-onlycurrent
optIfOMSnSrcPrevDayTable
OBJECT-TYPE
A table of OMSn source performance monitoring information for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.9not-accessiblecurrent
optIfOMSnSrcPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OMSn source performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.9.1not-accessiblecurrent
optIfOMSnSrcPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.4.9.1.1TruthValueread-onlycurrent
optIfOMSnSrcPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.9.1.2Integer32read-onlycurrent
optIfOMSnSrcPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.9.1.3Integer32read-onlycurrent
optIfOMSnSrcPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.9.1.4Integer32read-onlycurrent
optIfOMSnSrcPrevDayLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.9.1.5Integer32read-onlycurrent
optIfOMSnSrcPrevDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.9.1.6Integer32read-onlycurrent
optIfOMSnSrcPrevDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.4.9.1.7Integer32read-onlycurrent
optIfOChGroup
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.5
optIfOChGroupConfigTable
OBJECT-TYPE
A table of OChGroup configuration information.
1.3.6.1.2.1.10.133.1.5.1not-accessiblecurrent
optIfOChGroupConfigEntry
OBJECT-TYPE
A conceptual row that contains OChGroup configuration information of an interface.
1.3.6.1.2.1.10.133.1.5.1.1not-accessiblecurrent
optIfOChGroupDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.2.1.10.133.1.5.1.1.1OptIfDirectionalityread-onlycurrent
optIfOChGroupSinkCurrentTable
OBJECT-TYPE
A table of OChGroup sink performance monitoring information for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.2not-accessiblecurrent
optIfOChGroupSinkCurrentEntry
OBJECT-TYPE
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.2.1not-accessiblecurrent
optIfOChGroupSinkCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.5.2.1.1TruthValueread-onlycurrent
optIfOChGroupSinkCurrentAggregatedInputPower
OBJECT-TYPE
The aggregated optical power of all the DWDM input channels in the OChGroup.
1.3.6.1.2.1.10.133.1.5.2.1.2Integer32read-onlycurrent
optIfOChGroupSinkCurrentLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.2.1.3Integer32read-onlycurrent
optIfOChGroupSinkCurrentHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.2.1.4Integer32read-onlycurrent
optIfOChGroupSinkCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on aggregated input power. If optIfOChGroupSinkCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.5.2.1.5Integer32read-writecurrent
optIfOChGroupSinkCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on aggregated input power. If optIfOChGroupSinkCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.5.2.1.6Integer32read-writecurrent
optIfOChGroupSinkCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output in the OChGroup.
1.3.6.1.2.1.10.133.1.5.2.1.7Integer32read-onlycurrent
optIfOChGroupSinkCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output in the OChGroup during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.2.1.8Integer32read-onlycurrent
optIfOChGroupSinkCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output in the OChGroup during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.2.1.9Integer32read-onlycurrent
optIfOChGroupSinkCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on the output power. If optIfOChGroupSinkCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.5.2.1.10Integer32read-writecurrent
optIfOChGroupSinkCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on the output power. If optIfOChGroupSinkCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.5.2.1.11Integer32read-writecurrent
optIfOChGroupSinkIntervalTable
OBJECT-TYPE
A table of historical OChGroup sink performance monitoring information.
1.3.6.1.2.1.10.133.1.5.3not-accessiblecurrent
optIfOChGroupSinkIntervalEntry
OBJECT-TYPE
A conceptual row that contains OChGroup sink performance monitoring information of an interface during a particular historical interval.
1.3.6.1.2.1.10.133.1.5.3.1not-accessiblecurrent
optIfOChGroupSinkIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.2.1.10.133.1.5.3.1.1OptIfIntervalNumbernot-accessiblecurrent
optIfOChGroupSinkIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.5.3.1.2TruthValueread-onlycurrent
optIfOChGroupSinkIntervalLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
1.3.6.1.2.1.10.133.1.5.3.1.3Integer32read-onlycurrent
optIfOChGroupSinkIntervalLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
1.3.6.1.2.1.10.133.1.5.3.1.4Integer32read-onlycurrent
optIfOChGroupSinkIntervalHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the interval.
1.3.6.1.2.1.10.133.1.5.3.1.5Integer32read-onlycurrent
optIfOChGroupSinkIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output in the OChGroup during the interval.
1.3.6.1.2.1.10.133.1.5.3.1.6Integer32read-onlycurrent
optIfOChGroupSinkIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output in the OChGroup during the interval.
1.3.6.1.2.1.10.133.1.5.3.1.7Integer32read-onlycurrent
optIfOChGroupSinkIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output in the OChGroup during the interval.
1.3.6.1.2.1.10.133.1.5.3.1.8Integer32read-onlycurrent
optIfOChGroupSinkCurDayTable
OBJECT-TYPE
A table of OChGroup sink performance monitoring information for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.4not-accessiblecurrent
optIfOChGroupSinkCurDayEntry
OBJECT-TYPE
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.4.1not-accessiblecurrent
optIfOChGroupSinkCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.5.4.1.1TruthValueread-onlycurrent
optIfOChGroupSinkCurDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.4.1.2Integer32read-onlycurrent
optIfOChGroupSinkCurDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.4.1.3Integer32read-onlycurrent
optIfOChGroupSinkCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output in the OChGroup during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.4.1.4Integer32read-onlycurrent
optIfOChGroupSinkCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output in the OChGroup during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.4.1.5Integer32read-onlycurrent
optIfOChGroupSinkPrevDayTable
OBJECT-TYPE
A table of OChGroup sink performance monitoring information for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.5not-accessiblecurrent
optIfOChGroupSinkPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OChGroup sink performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.5.1not-accessiblecurrent
optIfOChGroupSinkPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.5.5.1.1TruthValueread-onlycurrent
optIfOChGroupSinkPrevDayLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.5.1.2Integer32read-onlycurrent
optIfOChGroupSinkPrevDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.5.1.3Integer32read-onlycurrent
optIfOChGroupSinkPrevDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power of all the DWDM input channels in the OChGroup during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.5.1.4Integer32read-onlycurrent
optIfOChGroupSinkPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output in the OChGroup during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.5.1.5Integer32read-onlycurrent
optIfOChGroupSinkPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output in the OChGroup during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.5.1.6Integer32read-onlycurrent
optIfOChGroupSinkPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output in the OChGroup during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.5.1.7Integer32read-onlycurrent
optIfOChGroupSrcCurrentTable
OBJECT-TYPE
A table of OChGroup source performance monitoring information for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.6not-accessiblecurrent
optIfOChGroupSrcCurrentEntry
OBJECT-TYPE
A conceptual row that contains OChGroup source performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.6.1not-accessiblecurrent
optIfOChGroupSrcCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.5.6.1.1TruthValueread-onlycurrent
optIfOChGroupSrcCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.2.1.10.133.1.5.6.1.2Integer32read-onlycurrent
optIfOChGroupSrcCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.6.1.3Integer32read-onlycurrent
optIfOChGroupSrcCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.6.1.4Integer32read-onlycurrent
optIfOChGroupSrcCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If optIfOChGroupSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.5.6.1.5Integer32read-writecurrent
optIfOChGroupSrcCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If optIfOChGroupSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.5.6.1.6Integer32read-writecurrent
optIfOChGroupSrcCurrentAggregatedInputPower
OBJECT-TYPE
The aggregated optical power monitored at the input.
1.3.6.1.2.1.10.133.1.5.6.1.7Integer32read-onlycurrent
optIfOChGroupSrcCurrentLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power monitored at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.6.1.8Integer32read-onlycurrent
optIfOChGroupSrcCurrentHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power monitored at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.5.6.1.9Integer32read-onlycurrent
optIfOChGroupSrcCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on input power. If optIfOChGroupSrcCurrentAggregatedInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.5.6.1.10Integer32read-writecurrent
optIfOChGroupSrcCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on input power. If optIfOChGroupSrcCurrentAggregatedInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.5.6.1.11Integer32read-writecurrent
optIfOChGroupSrcIntervalTable
OBJECT-TYPE
A table of historical OChGroup source performance monitoring information.
1.3.6.1.2.1.10.133.1.5.7not-accessiblecurrent
optIfOChGroupSrcIntervalEntry
OBJECT-TYPE
A conceptual row that contains OChGroup source performance monitoring information of an interface during a particular historical interval.
1.3.6.1.2.1.10.133.1.5.7.1not-accessiblecurrent
optIfOChGroupSrcIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.2.1.10.133.1.5.7.1.1OptIfIntervalNumbernot-accessiblecurrent
optIfOChGroupSrcIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.5.7.1.2TruthValueread-onlycurrent
optIfOChGroupSrcIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.5.7.1.3Integer32read-onlycurrent
optIfOChGroupSrcIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.5.7.1.4Integer32read-onlycurrent
optIfOChGroupSrcIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.5.7.1.5Integer32read-onlycurrent
optIfOChGroupSrcIntervalLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.5.7.1.6Integer32read-onlycurrent
optIfOChGroupSrcIntervalLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.5.7.1.7Integer32read-onlycurrent
optIfOChGroupSrcIntervalHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.5.7.1.8Integer32read-onlycurrent
optIfOChGroupSrcCurDayTable
OBJECT-TYPE
A table of OChGroup source performance monitoring information for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.8not-accessiblecurrent
optIfOChGroupSrcCurDayEntry
OBJECT-TYPE
A conceptual row that contains OChGroup source performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.8.1not-accessiblecurrent
optIfOChGroupSrcCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.5.8.1.1TruthValueread-onlycurrent
optIfOChGroupSrcCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.8.1.2Integer32read-onlycurrent
optIfOChGroupSrcCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.8.1.3Integer32read-onlycurrent
optIfOChGroupSrcCurDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power monitored at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.8.1.4Integer32read-onlycurrent
optIfOChGroupSrcCurDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power monitored at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.5.8.1.5Integer32read-onlycurrent
optIfOChGroupSrcPrevDayTable
OBJECT-TYPE
A table of OChGroup source performance monitoring information for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.9not-accessiblecurrent
optIfOChGroupSrcPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OChGroup source performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.9.1not-accessiblecurrent
optIfOChGroupSrcPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.5.9.1.1TruthValueread-onlycurrent
optIfOChGroupSrcPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.9.1.2Integer32read-onlycurrent
optIfOChGroupSrcPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.9.1.3Integer32read-onlycurrent
optIfOChGroupSrcPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.9.1.4Integer32read-onlycurrent
optIfOChGroupSrcPrevDayLastAggregatedInputPower
OBJECT-TYPE
The last aggregated optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.9.1.5Integer32read-onlycurrent
optIfOChGroupSrcPrevDayLowAggregatedInputPower
OBJECT-TYPE
The lowest aggregated optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.9.1.6Integer32read-onlycurrent
optIfOChGroupSrcPrevDayHighAggregatedInputPower
OBJECT-TYPE
The highest aggregated optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.5.9.1.7Integer32read-onlycurrent
optIfOCh
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.6
optIfOChConfigTable
OBJECT-TYPE
A table of OCh configuration information.
1.3.6.1.2.1.10.133.1.6.1not-accessiblecurrent
optIfOChConfigEntry
OBJECT-TYPE
A conceptual row that contains OCh configuration information of an interface.
1.3.6.1.2.1.10.133.1.6.1.1not-accessiblecurrent
optIfOChDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.2.1.10.133.1.6.1.1.1OptIfDirectionalityread-onlycurrent
optIfOChCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is applicable when optIfOChDirectionality has the value sink(1) or bidirectional(3). In full-capability systems the bit position los(1) is not used. In reduced-capability systems or at IrDI interfaces only the bit positions los(1) and ssfP(3) are used.
1.3.6.1.2.1.10.133.1.6.1.1.2Bits {losP(0), los(1), oci(2), ssfP(3), ssfO(4), ssf(5)}read-onlycurrent
optIfOChSinkCurrentTable
OBJECT-TYPE
A table of OCh sink performance monitoring information for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.6.2not-accessiblecurrent
optIfOChSinkCurrentEntry
OBJECT-TYPE
A conceptual row that contains OCh sink performance monitoring information for an interface for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.6.2.1not-accessiblecurrent
optIfOChSinkCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.6.2.1.1TruthValueread-onlycurrent
optIfOChSinkCurrentInputPower
OBJECT-TYPE
The optical power monitored at the input.
1.3.6.1.2.1.10.133.1.6.2.1.2Integer32read-onlycurrent
optIfOChSinkCurrentLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.6.2.1.3Integer32read-onlycurrent
optIfOChSinkCurrentHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.6.2.1.4Integer32read-onlycurrent
optIfOChSinkCurrentLowerInputPowerThreshold
OBJECT-TYPE
The lower limit threshold on input power. If optIfOChSinkCurrentInputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.6.2.1.5Integer32read-writecurrent
optIfOChSinkCurrentUpperInputPowerThreshold
OBJECT-TYPE
The upper limit threshold on input power. If optIfOChSinkCurrentInputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.6.2.1.6Integer32read-writecurrent
optIfOChSinkIntervalTable
OBJECT-TYPE
A table of historical OCh sink performance monitoring information.
1.3.6.1.2.1.10.133.1.6.3not-accessiblecurrent
optIfOChSinkIntervalEntry
OBJECT-TYPE
A conceptual row that contains OCh sink performance monitoring information of an interface during a particular historical interval.
1.3.6.1.2.1.10.133.1.6.3.1not-accessiblecurrent
optIfOChSinkIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.2.1.10.133.1.6.3.1.1OptIfIntervalNumbernot-accessiblecurrent
optIfOChSinkIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.6.3.1.2TruthValueread-onlycurrent
optIfOChSinkIntervalLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.6.3.1.3Integer32read-onlycurrent
optIfOChSinkIntervalLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.6.3.1.4Integer32read-onlycurrent
optIfOChSinkIntervalHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the interval.
1.3.6.1.2.1.10.133.1.6.3.1.5Integer32read-onlycurrent
optIfOChSinkCurDayTable
OBJECT-TYPE
A table of OCh sink performance monitoring information for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.6.4not-accessiblecurrent
optIfOChSinkCurDayEntry
OBJECT-TYPE
A conceptual row that contains OCh sink performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.6.4.1not-accessiblecurrent
optIfOChSinkCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.6.4.1.1TruthValueread-onlycurrent
optIfOChSinkCurDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.6.4.1.2Integer32read-onlycurrent
optIfOChSinkCurDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.6.4.1.3Integer32read-onlycurrent
optIfOChSinkPrevDayTable
OBJECT-TYPE
A table of OCh sink performance monitoring information for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.5not-accessiblecurrent
optIfOChSinkPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OCh sink performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.5.1not-accessiblecurrent
optIfOChSinkPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.6.5.1.1TruthValueread-onlycurrent
optIfOChSinkPrevDayLastInputPower
OBJECT-TYPE
The last optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.5.1.2Integer32read-onlycurrent
optIfOChSinkPrevDayLowInputPower
OBJECT-TYPE
The lowest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.5.1.3Integer32read-onlycurrent
optIfOChSinkPrevDayHighInputPower
OBJECT-TYPE
The highest optical power monitored at the input during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.5.1.4Integer32read-onlycurrent
optIfOChSrcCurrentTable
OBJECT-TYPE
A table of OCh source performance monitoring information for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.6.6not-accessiblecurrent
optIfOChSrcCurrentEntry
OBJECT-TYPE
A conceptual row that contains OCh source performance monitoring information of an interface for the current 15-minute interval.
1.3.6.1.2.1.10.133.1.6.6.1not-accessiblecurrent
optIfOChSrcCurrentSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.6.6.1.1TruthValueread-onlycurrent
optIfOChSrcCurrentOutputPower
OBJECT-TYPE
The optical power monitored at the output.
1.3.6.1.2.1.10.133.1.6.6.1.2Integer32read-onlycurrent
optIfOChSrcCurrentLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.6.6.1.3Integer32read-onlycurrent
optIfOChSrcCurrentHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 15-minute interval.
1.3.6.1.2.1.10.133.1.6.6.1.4Integer32read-onlycurrent
optIfOChSrcCurrentLowerOutputPowerThreshold
OBJECT-TYPE
The lower limit threshold on output power. If optIfOChSrcCurrentOutputPower drops to this value or below, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.6.6.1.5Integer32read-writecurrent
optIfOChSrcCurrentUpperOutputPowerThreshold
OBJECT-TYPE
The upper limit threshold on output power. If optIfOChSrcCurrentOutputPower reaches or exceeds this value, a Threshold Crossing Alert (TCA) should be sent.
1.3.6.1.2.1.10.133.1.6.6.1.6Integer32read-writecurrent
optIfOChSrcIntervalTable
OBJECT-TYPE
A table of historical OCh source performance monitoring information.
1.3.6.1.2.1.10.133.1.6.7not-accessiblecurrent
optIfOChSrcIntervalEntry
OBJECT-TYPE
A conceptual row that contains OCh source performance monitoring information of an interface during a particular historical interval.
1.3.6.1.2.1.10.133.1.6.7.1not-accessiblecurrent
optIfOChSrcIntervalNumber
OBJECT-TYPE
Uniquely identifies the interval.
1.3.6.1.2.1.10.133.1.6.7.1.1OptIfIntervalNumbernot-accessiblecurrent
optIfOChSrcIntervalSuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.6.7.1.2TruthValueread-onlycurrent
optIfOChSrcIntervalLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.6.7.1.3Integer32read-onlycurrent
optIfOChSrcIntervalLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.6.7.1.4Integer32read-onlycurrent
optIfOChSrcIntervalHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the interval.
1.3.6.1.2.1.10.133.1.6.7.1.5Integer32read-onlycurrent
optIfOChSrcCurDayTable
OBJECT-TYPE
A table of OCh source performance monitoring information for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.6.8not-accessiblecurrent
optIfOChSrcCurDayEntry
OBJECT-TYPE
A conceptual row that contains OCh source performance monitoring information of an interface for the current 24-hour interval.
1.3.6.1.2.1.10.133.1.6.8.1not-accessiblecurrent
optIfOChSrcCurDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.6.8.1.1TruthValueread-onlycurrent
optIfOChSrcCurDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.6.8.1.2Integer32read-onlycurrent
optIfOChSrcCurDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the current 24-hour interval.
1.3.6.1.2.1.10.133.1.6.8.1.3Integer32read-onlycurrent
optIfOChSrcPrevDayTable
OBJECT-TYPE
A table of OCh source performance monitoring information for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.9not-accessiblecurrent
optIfOChSrcPrevDayEntry
OBJECT-TYPE
A conceptual row that contains OCh source performance monitoring information of an interface for the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.9.1not-accessiblecurrent
optIfOChSrcPrevDaySuspectedFlag
OBJECT-TYPE
If true, the data in this entry may be unreliable.
1.3.6.1.2.1.10.133.1.6.9.1.1TruthValueread-onlycurrent
optIfOChSrcPrevDayLastOutputPower
OBJECT-TYPE
The last optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.9.1.2Integer32read-onlycurrent
optIfOChSrcPrevDayLowOutputPower
OBJECT-TYPE
The lowest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.9.1.3Integer32read-onlycurrent
optIfOChSrcPrevDayHighOutputPower
OBJECT-TYPE
The highest optical power monitored at the output during the previous 24-hour interval.
1.3.6.1.2.1.10.133.1.6.9.1.4Integer32read-onlycurrent
optIfOTUk
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.7
optIfOTUkConfigTable
OBJECT-TYPE
A table of OTUk configuration information.
1.3.6.1.2.1.10.133.1.7.1not-accessiblecurrent
optIfOTUkConfigEntry
OBJECT-TYPE
A conceptual row that contains OTUk configuration information of an interface.
1.3.6.1.2.1.10.133.1.7.1.1not-accessiblecurrent
optIfOTUkDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.2.1.10.133.1.7.1.1.1OptIfDirectionalityread-onlycurrent
optIfOTUkBitRateK
OBJECT-TYPE
Indicates the bit rate of the entity.
1.3.6.1.2.1.10.133.1.7.1.1.2OptIfBitRateKread-onlycurrent
optIfOTUkTraceIdentifierTransmitted
OBJECT-TYPE
The trace identifier transmitted. This object is applicable when optIfOTUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value sink(1). If no value is ever set by a management entity for this object, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
1.3.6.1.2.1.10.133.1.7.1.1.3OptIfTxTIread-writecurrent
optIfOTUkDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). This object has no effect when optIfOTUkTIMDetMode has the value off(1).
1.3.6.1.2.1.10.133.1.7.1.1.4OptIfExDAPIread-writecurrent
optIfOTUkSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). This object has no effect when optIfOTUkTIMDetMode has the value off(1).
1.3.6.1.2.1.10.133.1.7.1.1.5OptIfExSAPIread-writecurrent
optIfOTUkTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The value of this object is unspecified when optIfOTUkCurrentStatus indicates a near-end defect (i.e., ssf(3), lof(4), ais(5), lom(6)) that prevents extraction of the trace message.
1.3.6.1.2.1.10.133.1.7.1.1.6OptIfAcTIread-onlycurrent
optIfOTUkTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is off(1).
1.3.6.1.2.1.10.133.1.7.1.1.7OptIfTIMDetModeread-writecurrent
optIfOTUkTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). This object has no effect when optIfOTUkTIMDetMode has the value off(1). The default value of this object is false(2).
1.3.6.1.2.1.10.133.1.7.1.1.8TruthValueread-writecurrent
optIfOTUkDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfOTUkDEGThr. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
1.3.6.1.2.1.10.133.1.7.1.1.9OptIfDEGThrread-writecurrent
optIfOTUkDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfOTUkDEGM consecutive bad PM Seconds are detected. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is 7 (See ITU-T G.7710).
1.3.6.1.2.1.10.133.1.7.1.1.10OptIfDEGMread-writecurrent
optIfOTUkSinkAdaptActive
OBJECT-TYPE
Indicates whether the sink adaptation function is activated or not. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is false(2).
1.3.6.1.2.1.10.133.1.7.1.1.11TruthValueread-writecurrent
optIfOTUkSourceAdaptActive
OBJECT-TYPE
Indicates whether the source adaptation function is activated or not. This object is only applicable to the source function, i.e., only when optIfOTUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value sink(1). The default value of this object is false(2).
1.3.6.1.2.1.10.133.1.7.1.1.12TruthValueread-writecurrent
optIfOTUkSinkFECEnabled
OBJECT-TYPE
If Forward Error Correction (FEC) is supported, this object indicates whether FEC at the OTUk sink adaptation function is enabled or not. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2). The default value of this object is true(1).
1.3.6.1.2.1.10.133.1.7.1.1.13TruthValueread-writecurrent
optIfOTUkCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is only applicable to the sink function, i.e., only when optIfOTUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfOTUkDirectionality has the value source(2).
1.3.6.1.2.1.10.133.1.7.1.1.14Bits {tim(0), deg(1), bdi(2), ssf(3), lof(4), ais(5), lom(6)}read-onlycurrent
optIfGCC0ConfigTable
OBJECT-TYPE
A table of GCC0 configuration information.
1.3.6.1.2.1.10.133.1.7.2not-accessiblecurrent
optIfGCC0ConfigEntry
OBJECT-TYPE
A conceptual row that contains GCC0 configuration information of an interface. Each instance must correspond to an instance of optIfOTUkConfigEntry. Separate source and/or sink instances may exist for a given ifIndex value, or a single bidirectional instance may exist, but a bidirectional instance may not coexist with a source or sink instance. Instances of this conceptual row persist across agent restarts.
1.3.6.1.2.1.10.133.1.7.2.1not-accessiblecurrent
optIfGCC0Directionality
OBJECT-TYPE
Indicates the directionality of the entity. The values source(2) and bidirectional(3) are not allowed if the corresponding instance of optIfOTUkDirectionality has the value sink(1). The values sink(1) and bidirectional(3) are not allowed if the corresponding instance of optIfOTUkDirectionality has the value source(2).
1.3.6.1.2.1.10.133.1.7.2.1.1OptIfDirectionalitynot-accessiblecurrent
optIfGCC0Application
OBJECT-TYPE
Indicates the application transported by the GCC0 entity. Example applications are ECC, User data channel. The value of this object may not be changed when optIfGCC0RowStatus has the value active(1).
1.3.6.1.2.1.10.133.1.7.2.1.2SnmpAdminStringread-createcurrent
optIfGCC0RowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the optIfGCC0 config table. It is used to model the addGCC0Access and removeGCC0Access operations of an OTUk_TTP for GCC0 access control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies addGCC0Access. Setting RowStatus to destroy implies removeGCC0Access.
1.3.6.1.2.1.10.133.1.7.2.1.3RowStatusread-createcurrent
optIfODUk
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.8
optIfODUkConfigTable
OBJECT-TYPE
A table of ODUk configuration information.
1.3.6.1.2.1.10.133.1.8.1not-accessiblecurrent
optIfODUkConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUk configuration information of an interface.
1.3.6.1.2.1.10.133.1.8.1.1not-accessiblecurrent
optIfODUkDirectionality
OBJECT-TYPE
Indicates the directionality of the entity.
1.3.6.1.2.1.10.133.1.8.1.1.1OptIfDirectionalityread-onlycurrent
optIfODUkBitRateK
OBJECT-TYPE
Indicates the bit rate of the entity.
1.3.6.1.2.1.10.133.1.8.1.1.2OptIfBitRateKread-onlycurrent
optIfODUkTcmFieldsInUse
OBJECT-TYPE
Indicates the TCM field(s) that are currently in use. The positions of the bits correspond to the TCM fields. A bit that is set to 1 means that the corresponding TCM field is used. This object will be updated when rows are created in or deleted from the optIfODUkTConfigTable, or the optIfODUkTNimConfigTable.
1.3.6.1.2.1.10.133.1.8.1.1.3Bits {tcmField1(0), tcmField2(1), tcmField3(2), tcmField4(3), tcmField5(4), tcmField6(5)}read-onlycurrent
optIfODUkPositionSeqCurrentSize
OBJECT-TYPE
This variable indicates the current size of the position sequence (i.e., number of TCM function and/or GCC12 access that have been created in the ODUk interface). When the value of this variable is greater than zero, it means that one or more TCM function and/or GCC12 access have been created in the ODUk interface. In this case, there will be as many rows in the optIfODUkPositionSeqTable as the value of optIfODUkPositionSeqCurrentSize corresponding to this ODUk interface, one row for each TCM function or GCC12 access. The position of the TCM function and/or GCC12 access within the sequence is indicated by the optIfODUkPositionSeqPosition variable in optIfODUkPositionSeqTable. The optIfODUkPositionSeqTable also provides pointers to the corresponding TCM function (optIfODUkT) and GCC12 access (optIfGCC12) entities.
1.3.6.1.2.1.10.133.1.8.1.1.4Unsigned32read-onlycurrent
optIfODUkTtpPresent
OBJECT-TYPE
This object has the value true(1) if the ifEntry under which it is instantiated contains an ODUk Trail Termination Point, i.e., is the endpoint of an ODUk path. In that case there will be a corresponding row in the ODUk TTP config table and it will not be possible to create corresponding rows in the ODUk NIM config table. This object has the value false(2) if the ifEntry under which it is instantiated contains an intermediate ODUk Connection Termination Point. In that case there is no corresponding row in the ODUk TTP config table, but it will be possible to create corresponding rows in the ODUk NIM config table. This object also affects the allowable options in rows created in the GCC12 config table and in the ODUkT config table, as specified in the DESCRIPTION clauses of the columns in those tables.
1.3.6.1.2.1.10.133.1.8.1.1.5TruthValueread-onlycurrent
optIfODUkTtpConfigTable
OBJECT-TYPE
A table of ODUk TTP configuration information.
1.3.6.1.2.1.10.133.1.8.2not-accessiblecurrent
optIfODUkTtpConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUk TTP configuration information of an interface.
1.3.6.1.2.1.10.133.1.8.2.1not-accessiblecurrent
optIfODUkTtpTraceIdentifierTransmitted
OBJECT-TYPE
The trace identifier transmitted. This object is applicable when optIfODUkDirectionality has the value source(2) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value sink(1). If no value is ever set by a management entity for this object, system-specific default value will be used. Any implementation that instantiates this object must document the system-specific default value or how it is derived.
1.3.6.1.2.1.10.133.1.8.2.1.1OptIfTxTIread-writecurrent
optIfODUkTtpDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). This object has no effect when optIfODUkTtpTIMDetMode has the value off(1).
1.3.6.1.2.1.10.133.1.8.2.1.2OptIfExDAPIread-writecurrent
optIfODUkTtpSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). This object has no effect when optIfODUkTtpTIMDetMode has the value off(1).
1.3.6.1.2.1.10.133.1.8.2.1.3OptIfExSAPIread-writecurrent
optIfODUkTtpTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). The value of this object is unspecified when optIfODUkTtpCurrentStatus indicates a near-end defect (i.e., oci(0), lck(1), ssf(5)) that prevents extraction of the trace message.
1.3.6.1.2.1.10.133.1.8.2.1.4OptIfAcTIread-onlycurrent
optIfODUkTtpTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). The default value of this object is off(1).
1.3.6.1.2.1.10.133.1.8.2.1.5OptIfTIMDetModeread-writecurrent
optIfODUkTtpTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). This object has no effect when optIfODUkTtpTIMDetMode has the value off(1). The default value of this object is false(2).
1.3.6.1.2.1.10.133.1.8.2.1.6TruthValueread-writecurrent
optIfODUkTtpDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfODUkDEGThr. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
1.3.6.1.2.1.10.133.1.8.2.1.7OptIfDEGThrread-writecurrent
optIfODUkTtpDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfODUkDEGM consecutive bad PM Seconds are detected. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2). The default value of this object is 7 (See ITU-T G.7710).
1.3.6.1.2.1.10.133.1.8.2.1.8OptIfDEGMread-writecurrent
optIfODUkTtpCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is only applicable to the sink function, i.e., only when optIfODUkDirectionality has the value sink(1) or bidirectional(3). It must not be instantiated in rows where optIfODUkDirectionality has the value source(2).
1.3.6.1.2.1.10.133.1.8.2.1.9Bits {oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)}read-onlycurrent
optIfODUkPositionSeqTable
OBJECT-TYPE
A table of ODUk Position Sequence information.
1.3.6.1.2.1.10.133.1.8.3not-accessiblecurrent
optIfODUkPositionSeqEntry
OBJECT-TYPE
A conceptual row that contains ODUk position sequence information of an ODUk interface. The ODUk interface is identified by the ifIndex. Associated with each ODUk interface there may be one of more conceptual rows in the optIfODUkPositionSeqTable. Each row represents a TCM or GCC12 access function within the associated ODUk interface. Rows of the optIfODUkPositionSeqTable table are created/deleted as the result of the creation/deletion of the optIfODUkT or optIfGCC12 entities.
1.3.6.1.2.1.10.133.1.8.3.1not-accessiblecurrent
optIfODUkPositionSeqIndex
OBJECT-TYPE
This variable identifies a row in the optIfODUkPositionSeqTable Table. Each row of the optIfODUkPositionSeqTable Table represents a TCM or GCC12 access function within the associated ODUk interface.
1.3.6.1.2.1.10.133.1.8.3.1.1Unsigned32 (1..4294967295)not-accessiblecurrent
optIfODUkPositionSeqPosition
OBJECT-TYPE
This variable indicates the position of the TCM or GCC12 access function within the sequence of TCMs & GCC12 access functions of the associated ODUk interface. The TCM or GCC12 presented by this row is referenced by the optIfODUkPositionSeqPointer variable.
1.3.6.1.2.1.10.133.1.8.3.1.2Unsigned32read-onlycurrent
optIfODUkPositionSeqPointer
OBJECT-TYPE
This variable identifies the TCM or GCC12 access function by pointing to the corresponding optIfODUkT or optIfGCC12 entity.
1.3.6.1.2.1.10.133.1.8.3.1.3RowPointerread-onlycurrent
optIfODUkNimConfigTable
OBJECT-TYPE
A table of ODUkNim configuration information.
1.3.6.1.2.1.10.133.1.8.4not-accessiblecurrent
optIfODUkNimConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUkNim configuration information of an interface. Each instance must correspond to an instance of optIfODUkConfigEntry for which optIfODUkTtpPresent has the value false(2). Instances of this conceptual row persist across agent restarts, and read-create columns other than the status column may be modified while the row is active.
1.3.6.1.2.1.10.133.1.8.4.1not-accessiblecurrent
optIfODUkNimDirectionality
OBJECT-TYPE
Specifies the monitor point for the ODUk Path non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of optIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of optIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of optIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction path signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP. Monitoring the source direction of an ODUk CTP is necessary in those cases where the ODUk CTP is at an SNCP (Subnetwork Connection Protection) end (e.g., see Figure I.1.2/G.874.1). If one would like to get the performance of the protected connection, one cannot use the NIM function at both ODUk CTP sinks (before the matrix), instead one should monitor the signal at the source ODUk CTP after the matrix.
1.3.6.1.2.1.10.133.1.8.4.1.1OptIfSinkOrSourcenot-accessiblecurrent
optIfODUkNimDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object has no effect if optIfODUkNimTIMDetMode has the value off(1) or sapi(3).
1.3.6.1.2.1.10.133.1.8.4.1.2OptIfExDAPIread-createcurrent
optIfODUkNimSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object has no effect if optIfODUkNimTIMDetMode has the value off(1) or dapi(2).
1.3.6.1.2.1.10.133.1.8.4.1.3OptIfExSAPIread-createcurrent
optIfODUkNimTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. The value of this object is unspecified if optIfODUkNimCurrentStatus has any of the bit positions oci(0), lck(1), or ssf(5) set or if optIfODUkNimRowStatus has any value other than active(1).
1.3.6.1.2.1.10.133.1.8.4.1.4OptIfAcTIread-onlycurrent
optIfODUkNimTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
1.3.6.1.2.1.10.133.1.8.4.1.5OptIfTIMDetModeread-createcurrent
optIfODUkNimTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled.
1.3.6.1.2.1.10.133.1.8.4.1.6TruthValueread-createcurrent
optIfODUkNimDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfODUkNimDEGThr.
1.3.6.1.2.1.10.133.1.8.4.1.7OptIfDEGThrread-createcurrent
optIfODUkNimDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfODUkNimDEGM consecutive bad PM Seconds are detected.
1.3.6.1.2.1.10.133.1.8.4.1.8OptIfDEGMread-createcurrent
optIfODUkNimCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. The value of this object is unspecified if optIfODUkNimRowStatus has any value other than active(1).
1.3.6.1.2.1.10.133.1.8.4.1.9Bits {oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)}read-onlycurrent
optIfODUkNimRowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the optIfODUkNim config table. It is used to model the activateNim and deactivateNim operations of an OTUk_CTP for non-intrusive monitoring control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies activateNim. Setting RowStatus to destroy implies deactivateNim.
1.3.6.1.2.1.10.133.1.8.4.1.10RowStatusread-createcurrent
optIfGCC12ConfigTable
OBJECT-TYPE
A table of GCC12 configuration information. The GCC function processes the GCC overhead bytes passing through them but leave the remainder of the ODUk overhead and payload data alone.
1.3.6.1.2.1.10.133.1.8.5not-accessiblecurrent
optIfGCC12ConfigEntry
OBJECT-TYPE
A conceptual row that contains GCC12 configuration information of an interface. Each instance must correspond to an instance of optIfODUkConfigEntry. Separate instances providing GCC1-only access and GCC2-only access may exist for a given ifIndex value, or a single instance providing GCC1 + GCC2 may exist, but a GCC1 + GCC2 instance may not coexist with a GCC1-only or GCC2-only instance. Instances of this conceptual row persist across agent restarts.
1.3.6.1.2.1.10.133.1.8.5.1not-accessiblecurrent
optIfGCC12Codirectional
OBJECT-TYPE
Indicates the directionality of the GCC12 termination with respect to the associated ODUk CTP. The value true(1) means that the sink part of the GCC12 extracts COMMS data from the signal at the input to the ODUk CTP sink and the source part of the GCC12 inserts COMMS data into the signal at the output of the ODUk CTP source. The value false(2) means that the sink part of the GCC12 extracts COMMS data from the signal at the output of the ODUk CTP source and the source part of the GCC12 inserts COMMS data into the signal at the input of the ODUk CTP sink. This attribute may assume either value when the corresponding instance of optIfODUkTtpPresent has the value false(2). When the value of the corresponding instance of optIfODUkTtpPresent is true(1) then the only value allowed for this attribute is true(1).
1.3.6.1.2.1.10.133.1.8.5.1.1TruthValuenot-accessiblecurrent
optIfGCC12GCCAccess
OBJECT-TYPE
Indicates the GCC access represented by the entity.
1.3.6.1.2.1.10.133.1.8.5.1.2INTEGER {gcc1(1), gcc2(2), gcc1and2(3)}not-accessiblecurrent
optIfGCC12GCCPassThrough
OBJECT-TYPE
Controls whether the selected GCC overhead bytes are passed through or modified. The value true(1) means that the selected GCC overhead bytes are passed through unmodified from the ODUk CTP input to the ODUk CTP output. The value false(2) means that the selected GCC overhead bytes are set to zero at the ODUk CTP output after the extraction of the COMMS data. This object has no effect if the corresponding instance of optIfODUkTtpPresent has the value true(1). The value of this object may not be changed when optIfGCC12RowStatus has the value active(1).
1.3.6.1.2.1.10.133.1.8.5.1.3TruthValueread-createcurrent
optIfGCC12Application
OBJECT-TYPE
Indicates the application transported by the GCC12 entity. Example applications are ECC, User data channel. The value of this object may not be changed when optIfGCC12RowStatus has the value active(1).
1.3.6.1.2.1.10.133.1.8.5.1.4SnmpAdminStringread-createcurrent
optIfGCC12RowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the optIfGCC12 config table. It is used to model the addGCC12Access and removeGCC12Access operations of an ODUk_CTP or ODUk_TTP for GCC12 access control as defined in G.874.1. Setting RowStatus to createAndGo or createAndWait implies addGCC12Access. Setting RowStatus to destroy implies removeGCC12Access. Successful addition/removal of the GCC12 access function will result in updating the optIfODUkPositionSeqCurrentSize variable and the optIfODUkPositionSeqTable table of the associated ODUk entry in the optIfODUkConfigTable.
1.3.6.1.2.1.10.133.1.8.5.1.5RowStatusread-createcurrent
optIfODUkT
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.1.9
optIfODUkTConfigTable
OBJECT-TYPE
A table of ODUkT configuration information.
1.3.6.1.2.1.10.133.1.9.1not-accessiblecurrent
optIfODUkTConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUkT configuration information of an interface. Each instance must correspond to an instance of optIfODUkConfigEntry. Rows in this table are mutually exclusive with rows in the ODUkT NIM config table -- in other words, this row object may not be instantiated for a given pair of ifIndex and TCM field values if a corresponding instance of optIfODUkTNimConfigEntry already exists. Instances of this conceptual row persist across agent restarts. Except where noted otherwise, read-create columns other than the status column may be modified while the row is active.
1.3.6.1.2.1.10.133.1.9.1.1not-accessiblecurrent
optIfODUkTTcmField
OBJECT-TYPE
Indicates the tandem connection monitoring field of the ODUk OH. Valid values are integers from 1 to 6.
1.3.6.1.2.1.10.133.1.9.1.1.1Unsigned32 (1..6)not-accessiblecurrent
optIfODUkTCodirectional
OBJECT-TYPE
Indicates the directionality of the ODUkT termination point with respect to the associated ODUk CTP. The value true(1) means that the sink part of the ODUkT TP extracts TCM data from the signal at the input to the ODUk CTP sink and the source part of the ODUkT TP inserts TCM data into the signal at the output of the ODUk CTP source. The value false(2) means that the sink part of the ODUkT TP extracts TCM data from the signal at the output of the ODUk CTP source and the source part of the ODUkT TP inserts TCM data into the signal at the input of the ODUk CTP sink. This attribute may assume either value when the corresponding instance of optIfODUkTtpPresent has the value false(2). When the value of the corresponding instance of optIfODUkTtpPresent is true(1) then the only value allowed for this attribute is true(1).
1.3.6.1.2.1.10.133.1.9.1.1.2TruthValuenot-accessiblecurrent
optIfODUkTTraceIdentifierTransmitted
OBJECT-TYPE
The trace identifier transmitted. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value false(2), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value true(1). It must not be instantiated in rows for all other cases.
1.3.6.1.2.1.10.133.1.9.1.1.3OptIfTxTIread-createcurrent
optIfODUkTDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when optIfODUkTTIMDetMode has the value off(1).
1.3.6.1.2.1.10.133.1.9.1.1.4OptIfExDAPIread-createcurrent
optIfODUkTSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when optIfODUkTTIMDetMode has the value off(1).
1.3.6.1.2.1.10.133.1.9.1.1.5OptIfExSAPIread-createcurrent
optIfODUkTTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The value of this object is unspecified when optIfODUkTCurrentStatus indicates a near-end defect (i.e., oci(0), lck(1), ssf(5)) that prevents extraction of the trace message.
1.3.6.1.2.1.10.133.1.9.1.1.6OptIfAcTIread-onlycurrent
optIfODUkTTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is off(1).
1.3.6.1.2.1.10.133.1.9.1.1.7OptIfTIMDetModeread-createcurrent
optIfODUkTTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. This object has no effect when optIfODUkTTIMDetMode has the value off(1). The default value of this object is false(2).
1.3.6.1.2.1.10.133.1.9.1.1.8TruthValueread-createcurrent
optIfODUkTDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfODUkTDEGThr. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is Severely Errored Second (SES) Estimator (See ITU-T G.7710).
1.3.6.1.2.1.10.133.1.9.1.1.9OptIfDEGThrread-createcurrent
optIfODUkTDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfODUkTDEGM consecutive bad PM Seconds are detected. This object is applicable only to the following three cases. (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases. The default value of this object is 7 (See ITU-T G.7710).
1.3.6.1.2.1.10.133.1.9.1.1.10OptIfDEGMread-createcurrent
optIfODUkTSinkMode
OBJECT-TYPE
This variable specifies the TCM mode at the entity. The value operational(1) means that TCM Overhead (TCMOH) processes (see ITU-T G.798) shall be performed and consequent actions for AIS, Trail Signal Fail (TSF), Trail Signal Degraded (TSD) shall be initiated in case of defects. The value monitor(2) means that TCMOH processes shall be performed but consequent actions for AIS, Trail Server Failure (TSF), Trail Server Degraded (TSD) shall _not_ be initiated in case of defects. This object is applicable only when the value of optIfODUkTtpPresent is false(2) and also either one of the following three cases holds: (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
1.3.6.1.2.1.10.133.1.9.1.1.11INTEGER {operational(1), monitor(2)}read-createcurrent
optIfODUkTSinkLockSignalAdminState
OBJECT-TYPE
Provides the capability to provision the LOCK signal, which is one of the ODUk maintenance signals, at the ODUKT sink. When a Tandem Connection endpoint is set to admin state locked, it inserts the ODUk-LCK signal in the sink direction. This object is applicable only when the value of optIfODUkTtpPresent is false(2) and also either one of the following three cases holds: (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
1.3.6.1.2.1.10.133.1.9.1.1.12INTEGER {locked(1), normal(2)}read-createcurrent
optIfODUkTSourceLockSignalAdminState
OBJECT-TYPE
Provides the capability to provision the LOCK signal, which is one of the ODUk maintenance signals, at the source. When a Tandem Connection endpoint is set to admin state locked, it inserts the ODUk-LCK signal in the source direction. This object is applicable only when either one of the following three cases holds: (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value false(2), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value true(1). It must not be instantiated in rows for all other cases.
1.3.6.1.2.1.10.133.1.9.1.1.13INTEGER {locked(1), normal(2)}read-createcurrent
optIfODUkTCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. This object is applicable only when either one of the following three cases holds: (i) optIfODUkDirectionality has the value bidirectional(3), or (ii) optIfODUkDirectionality has the value sink(1) and optIfODUkTCodirectional has the value true(1), or (iii) optIfODUkDirectionality has the value source(3) and optIfODUkTCodirectional has the value false(2). It must not be instantiated in rows for all other cases.
1.3.6.1.2.1.10.133.1.9.1.1.14Bits {oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)}read-onlycurrent
optIfODUkTRowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the optIfODUkT config table. It is used to model the addTCM and removeTCM operations of an ODUk_CTP or ODUk_TTP for Tandem connection monitoring as defined in ITU-T G.874.1. Setting RowStatus to createAndGo or createAndWait implies addTCM. Setting RowStatus to destroy implies removeTCM. Successful addition/removal of TCM will result in updating the optIfODUkTcmFieldsInUse and optIfODUkPositionSeqCurrentSize variables and the optIfODUkPositionSeqTable table of the associated ODUk entry in the optIfODUkConfigTable.
1.3.6.1.2.1.10.133.1.9.1.1.15RowStatusread-createcurrent
optIfODUkTNimConfigTable
OBJECT-TYPE
A table of ODUkTNim configuration information.
1.3.6.1.2.1.10.133.1.9.2not-accessiblecurrent
optIfODUkTNimConfigEntry
OBJECT-TYPE
A conceptual row that contains ODUkTNim configuration information of an interface. Each instance must correspond to an instance of optIfODUkConfigEntry. Rows in this table are mutually exclusive with rows in the ODUkT config table -- in other words, this row object may not be instantiated for a given pair of ifIndex and TCM field values if a corresponding instance of optIfODUkTConfigEntry already exists. Instances of this conceptual row persist across agent restarts, and read-create columns other than the status column may be modified while the row is active.
1.3.6.1.2.1.10.133.1.9.2.1not-accessiblecurrent
optIfODUkTNimTcmField
OBJECT-TYPE
Indicates the tandem connection monitoring field of the ODUk OH on which non-intrusive monitoring is performed. Valid values are integers from 1 to 6.
1.3.6.1.2.1.10.133.1.9.2.1.1Unsigned32 (1..6)not-accessiblecurrent
optIfODUkTNimDirectionality
OBJECT-TYPE
Specifies the monitor point for the ODUk TCM non-intrusive monitoring function. The value source(2) is not allowed if the corresponding instance of optIfODUkDirectionality has the value sink(1), and the value sink(1) is not allowed if the corresponding instance of optIfODUkDirectionality has the value source(2). Either the value sink(1) or source(2) is allowed if the corresponding instance of optIfODUkDirectionality has the value bidirectional(3). The value sink(1) means monitoring at the sink direction TCM signal of the ODUk CTP. The value source(2) means monitoring at the source direction path signal of the ODUk CTP.
1.3.6.1.2.1.10.133.1.9.2.1.2OptIfSinkOrSourcenot-accessiblecurrent
optIfODUkTNimDAPIExpected
OBJECT-TYPE
The DAPI expected by the receiver. This object has no effect if optIfODUkTNimTIMDetMode has the value off(1) or sapi(3).
1.3.6.1.2.1.10.133.1.9.2.1.3OptIfExDAPIread-createcurrent
optIfODUkTNimSAPIExpected
OBJECT-TYPE
The SAPI expected by the receiver. This object has no effect if optIfODUkTNimTIMDetMode has the value off(1) or dapi(2).
1.3.6.1.2.1.10.133.1.9.2.1.4OptIfExSAPIread-createcurrent
optIfODUkTNimTraceIdentifierAccepted
OBJECT-TYPE
The actual trace identifier accepted. The value of this object is unspecified if optIfODUkTNimCurrentStatus has any of the bit positions oci(0), lck(1), or ssf(5) set or if optIfODUkTNimRowStatus has any value other than active(1).
1.3.6.1.2.1.10.133.1.9.2.1.5OptIfAcTIread-onlycurrent
optIfODUkTNimTIMDetMode
OBJECT-TYPE
Indicates the mode of the Trace Identifier Mismatch (TIM) Detection function.
1.3.6.1.2.1.10.133.1.9.2.1.6OptIfTIMDetModeread-createcurrent
optIfODUkTNimTIMActEnabled
OBJECT-TYPE
Indicates whether the Trace Identifier Mismatch (TIM) Consequent Action function is enabled.
1.3.6.1.2.1.10.133.1.9.2.1.7TruthValueread-createcurrent
optIfODUkTNimDEGThr
OBJECT-TYPE
Indicates the threshold level for declaring a performance monitoring (PM) Second to be bad. A PM Second is declared bad if the percentage of detected errored blocks in that second is greater than or equal to optIfODUkTNimDEGThr.
1.3.6.1.2.1.10.133.1.9.2.1.8OptIfDEGThrread-createcurrent
optIfODUkTNimDEGM
OBJECT-TYPE
Indicates the threshold level for declaring a Degraded Signal defect (dDEG). A dDEG shall be declared if optIfODUkTNimDEGM consecutive bad PM Seconds are detected.
1.3.6.1.2.1.10.133.1.9.2.1.9OptIfDEGMread-createcurrent
optIfODUkTNimCurrentStatus
OBJECT-TYPE
Indicates the defect condition of the entity, if any. The value of this object is unspecified if optIfODUkTNimRowStatus has any value other than active(1).
1.3.6.1.2.1.10.133.1.9.2.1.10Bits {oci(0), lck(1), tim(2), deg(3), bdi(4), ssf(5)}read-onlycurrent
optIfODUkTNimRowStatus
OBJECT-TYPE
This columnar object is used for creating and deleting a conceptual row of the optIfODUkTNim config table. It is used to model the addTCM and removeTCM operations of an ODUk_CTP or ODUk_TTP for non-intrusive Tandem connection monitoring as defined in ITU-T G.874.1. Setting RowStatus to createAndGo or createAndWait implies addTCM. Setting RowStatus to destroy implies removeTCM. Successful addition/removal of Nim TCM will result in updating the optIfODUkPositionSeqCurrentSize variable and the optIfODUkPositionSeqTable table of the associated ODUk entry in the optIfODUkConfigTable.
1.3.6.1.2.1.10.133.1.9.2.1.11RowStatusread-createcurrent
optIfConfs
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.2
optIfGroups
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.2.1
optIfCompl
OBJECT-IDENTITY
1.3.6.1.2.1.10.133.2.2

Conformance

NameOIDStatus
optIfOTMnGroup
OBJECT-GROUP
A collection of OTMn structure information objects.
1.3.6.1.2.1.10.133.2.1.1current
optIfPerfMonGroup
OBJECT-GROUP
A collection of performance monitoring interval objects.
1.3.6.1.2.1.10.133.2.1.2current
optIfOTSnCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OTSn interfaces.
1.3.6.1.2.1.10.133.2.1.3current
optIfOTSnSourceGroupFull
OBJECT-GROUP
A collection of configuration objects applicable to full-functionality/IaDI OTSn interfaces that support source functions.
1.3.6.1.2.1.10.133.2.1.4current
optIfOTSnAPRStatusGroup
OBJECT-GROUP
A collection of objects applicable to OTSn interfaces that support Automatic Power Reduction functions.
1.3.6.1.2.1.10.133.2.1.5current
optIfOTSnAPRControlGroup
OBJECT-GROUP
A collection of objects applicable to OTSn interfaces that provide Automatic Power Reduction control functions.
1.3.6.1.2.1.10.133.2.1.6current
optIfOTSnSinkGroupBasic
OBJECT-GROUP
A collection of configuration objects applicable to all OTSn interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.7current
optIfOTSnSinkGroupFull
OBJECT-GROUP
A collection of configuration objects applicable to full-functionality/IaDI OTSn interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.8current
optIfOTSnSinkPreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OTSn interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.9current
optIfOTSnSinkPreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OTSn interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.10current
optIfOTSnSourcePreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OTSn interfaces that support source functions.
1.3.6.1.2.1.10.133.2.1.11current
optIfOTSnSourcePreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OTSn interfaces that support source functions.
1.3.6.1.2.1.10.133.2.1.12current
optIfOMSnCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OMSn interfaces.
1.3.6.1.2.1.10.133.2.1.13current
optIfOMSnSinkGroupBasic
OBJECT-GROUP
A collection of configuration objects applicable to all OMSn interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.14current
optIfOMSnSinkPreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OMSn interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.15current
optIfOMSnSinkPreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OMSn interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.16current
optIfOMSnSourcePreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OMSn interfaces that support source functions.
1.3.6.1.2.1.10.133.2.1.17current
optIfOMSnSourcePreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OMSn interfaces that that support source functions.
1.3.6.1.2.1.10.133.2.1.18current
optIfOChGroupCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OChGroup interfaces.
1.3.6.1.2.1.10.133.2.1.19current
optIfOChGroupSinkPreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OChGroup interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.20current
optIfOChGroupSinkPreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OChGroup interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.21current
optIfOChGroupSourcePreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OChGroup interfaces that support source functions.
1.3.6.1.2.1.10.133.2.1.22current
optIfOChGroupSourcePreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OChGroup interfaces that that support source functions.
1.3.6.1.2.1.10.133.2.1.23current
optIfOChCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OCh interfaces.
1.3.6.1.2.1.10.133.2.1.24current
optIfOChSinkGroupBasic
OBJECT-GROUP
A collection of configuration objects applicable to all OCh interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.25current
optIfOChSinkPreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OCh interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.26current
optIfOChSinkPreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OCh interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.27current
optIfOChSourcePreOtnPMGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring objects applicable to OCh interfaces that support source functions.
1.3.6.1.2.1.10.133.2.1.28current
optIfOChSourcePreOtnPMThresholdGroup
OBJECT-GROUP
A collection of pre-OTN performance monitoring threshold objects applicable to OCh interfaces that support source functions.
1.3.6.1.2.1.10.133.2.1.29current
optIfOTUkCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all OTUk interfaces.
1.3.6.1.2.1.10.133.2.1.30current
optIfOTUkSourceGroup
OBJECT-GROUP
A collection of configuration objects applicable to OTUk interfaces that support source functions.
1.3.6.1.2.1.10.133.2.1.31current
optIfOTUkSinkGroup
OBJECT-GROUP
A collection of configuration objects applicable to OTUk interfaces that support sink functions.
1.3.6.1.2.1.10.133.2.1.32current
optIfGCC0Group
OBJECT-GROUP
A collection of GCC0 configuration objects.
1.3.6.1.2.1.10.133.2.1.33current
optIfODUkGroup
OBJECT-GROUP
A collection of configuration objects applicable to all ODUk interfaces.
1.3.6.1.2.1.10.133.2.1.34current
optIfODUkTtpSourceGroup
OBJECT-GROUP
A collection of configuration objects applicable to all interfaces that support ODUk trail termination source functions.
1.3.6.1.2.1.10.133.2.1.35current
optIfODUkTtpSinkGroup
OBJECT-GROUP
A collection of ODUk configuration objects applicable to all interfaces that support ODUk trail termination sink functions.
1.3.6.1.2.1.10.133.2.1.36current
optIfODUkNimGroup
OBJECT-GROUP
A collection of ODUk Nim configuration objects.
1.3.6.1.2.1.10.133.2.1.37current
optIfGCC12Group
OBJECT-GROUP
A collection of GCC12 configuration objects.
1.3.6.1.2.1.10.133.2.1.38current
optIfODUkTCommonGroup
OBJECT-GROUP
A collection of configuration objects applicable to all ODUkT instances.
1.3.6.1.2.1.10.133.2.1.39current
optIfODUkTSourceGroup
OBJECT-GROUP
A collection of configuration objects applicable to all ODUkT instances that provide source functions.
1.3.6.1.2.1.10.133.2.1.40current
optIfODUkTSinkGroup
OBJECT-GROUP
A collection of configuration objects applicable to all ODUkT instances that provide sink functions.
1.3.6.1.2.1.10.133.2.1.41current
optIfODUkTSinkGroupCtp
OBJECT-GROUP
A collection of configuration objects applicable to ODUkT instances not colocated with an ODUk TTP that provide sink functions.
1.3.6.1.2.1.10.133.2.1.42current
optIfODUkTNimGroup
OBJECT-GROUP
A collection of ODUkT Nim configuration objects.
1.3.6.1.2.1.10.133.2.1.43current
optIfOtnConfigCompl
MODULE-COMPLIANCE
Implementation requirements for the OTN configuration functions defined in this MIB module.
1.3.6.1.2.1.10.133.2.2.1current
optIfPreOtnPMCompl
MODULE-COMPLIANCE
Implementation requirements for Pre-OTN performance monitoring functions defined in this MIB module.
1.3.6.1.2.1.10.133.2.2.2current