OMNITRON-MIB

OBJECT-TYPE

This a table of chassis and their modules.

OBJECT-TYPE

Chassis modules.

OBJECT-TYPE

The chassis where the module resides. Ranges in value from 1 - 19.

OBJECT-TYPE

The slot number of the module. For the 19 slot chassis it ranges in value from 1-22. For the 2 slot chassis it ranges in value from 1-2.

OBJECT-TYPE

Type of chassis: 1 = 19 module chassis 2 = 2 module chassis 3 = 5 module chassis 4 = 1 module chassis 5 = stand alone chassis 6 = 1-module redundant power chassis

OBJECT-TYPE

The product type of the module: 61 = iConverter NMM 64 = iConverter Power Supply (19 Module) 65 = iConverter 10FL/T Ethernet 66 = iConverter 100 Fx/Tx Ethernet 67 = iConverter Fiber/Fiber 68 = iConverter 10/100 Ethernet 70 = iConverter 2FXM slave 72 = iConverter GX/X 74 = iConverter Tx/2Tx Ethernet 75 = iConverter Gx Gigabit Ethernet 76 = iConverter Tx/2Fx Ethernet 77 = iConverter T1/E1 79 = iConverter 4Tx Ethernet 80 = iConverter 10/100M 81 = iConverter GX/T Ethernet 82 = iConverter Power Supply (5 Module) 83 = iConverter GX/F Ethernet 84 = iConverter 2FX Ethernet 85 = iConverter 10T/2 Ethernet 86 = iConverter 10/100VT Ethernet 87 = iConverter 4Tx VT 88 = iConverter RS 422/485 89 = iConverter T3/E3 90 = iConverter 10/100M slave 92 = iConverter RS 232 93 = iConverter GX/TM 94 = iConverter GX/TM slave 95 = iConverter 2GXM 96 = iConverter 2FXM 97 = iConverter GM3 2xSFP 98 = iConverter 2GXM slave 99 = iConverter GM3 2xUTP 100= iConverter 10/100M2 101= iConverter 2FXM2 102= iConverter GM3 SFP/2xUTP 103= iConverter 1-Module Redundant Powered Chassis 104= iConverter Gx AN 105= iConverter GX/TM2 106= iConverter 2GX/TM2 107= iConverter 4xT1/E1 Mux 108= iConverter GM3 2xSFP/UTP 109= iConverter GM3 3xSFP 110= iConverter X.21 112= iConverter GM3 3xUTP 113= iConverter GM3 FF/UTP or SFP/UTP 114= iConverter CWDM 115= iConverter XG 117= iConverter TM3 119= iConverter 4GT 120= iConverter GM4 2xSFP/TP 136= iConverter XGT+ 137= iConverter GM4 5-Port 142= iConverter GX/T2 143= iConverter GM4-HPoE or GM4-PoE+ 253= iConverter GM3 2XSFP 254= iConverter GM3 1xSFP/2xUTP 255= iConverter Unknown

OBJECT-TYPE

The name of the chassis. For the M2 modules the max size is 32 octets. For the GM3, GM4, XM5 the max size is 64 octets when a module is accessed directly through the serial port, or via its own IP address for Telnet, SSH, or SNMP. For the GM3, GM4, XM5 when the object is indirectly accessed via the backplane, through IP-less, or through 802.3ah peer-to-peer the value is truncated to 32 bytes.

OBJECT-TYPE

The part number of the module.

OBJECT-TYPE

The serial number of the module.

OBJECT-TYPE

The date the module was manufactured in form YYYYMMDD.

OBJECT-TYPE

The software revision of the module software.

OBJECT-TYPE

The product revision of the module.

OBJECT-TYPE

The status of any first 32 LEDs on the module, excluding the power LED. If an LED is missing its number is skipped. For an eight LED position device the following is the decoding: ledstat.7 is the top LED position ledstat.6 is the second LED position ledstat.5 is the third LED position ledstat.4 is the fourth LED position ledstat.3 is the fifth LED position ledstat.2 is the sixth LED position ledstat.1 is the seventh LED position ledstat.0 is the eighth and bottom LED position For devices that have 32 or less LEDs this object contains all the LEDs. For those devices that have more than 32 LEDs, LEDs 33 and above are only covered by the modExpLedStatus object.

OBJECT-TYPE

The status of any DIP switches on the module. DIP switch 1 is switchstat.0, DIP switch 2 is switchstat.1, DIP switch 3 is switchstat.2, etc. DIP switch bank 1 is switches 0-7 DIP switch bank 2 is switches 8-15 Front panel switches start at switchstat.7 for the top switch, switchstat.6 for the next switch, etc.

OBJECT-TYPE

General extended status for the module. Normally this is the actual setting of the DIP switch selection.

OBJECT-TYPE

General extended status for the module

OBJECT-TYPE

General extended status for the module

OBJECT-TYPE

General extended status for the module

OBJECT-TYPE

General extended status for the module

OBJECT-TYPE

General extended status for the module

OBJECT-TYPE

Writing to this variable resets the module. This variable is a write only. Writing a zero (0) will reboot to the current working application image Writing a one (1) will reboot to the backup application image if available

OBJECT-TYPE

Writing to this variable updates the module switch settings. See switchstat above for the explanation.

OBJECT-TYPE

The name of the module

OBJECT-TYPE

Holds the chassis number of the selected IP

OBJECT-TYPE

Holds the slot number of the selected IP

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The number of modules in the chassis table

OBJECT-TYPE

This a table of modules in the enhances chassis table. It contains as many entries as specified by moduleCount

OBJECT-TYPE

Chassis modules.

OBJECT-TYPE

The chassis where the module resides.

OBJECT-TYPE

The slot number within a chassis.

OBJECT-TYPE

The type of chassis in which the module resides.

OBJECT-TYPE

The chassis where the module resides.

OBJECT-TYPE

The modules software revision.

OBJECT-TYPE

The modules product revision.

OBJECT-TYPE

Writing to this variable resets the module. This variable is a write only. Writing a zero (0) will reboot to the current working application image Writing a one (1) will reboot to the backup application image if available

OBJECT-TYPE

The number of ports in this module.

OBJECT-TYPE

The name of the chassis in which the individual module resides in. For the M2 modules the max size is 32 octets. For the GM3, GM4, XM5 the max size is 64 octets when a module is accessed directly through the serial port, or via its own IP address for Telnet, SSH, or SNMP. For the GM3, GM4, XM5 when the object is indirectly accessed via the backplane, through IP-less, or through 802.3ah peer-to-peer the value is truncated to 32 bytes.

OBJECT-TYPE

The model of the individual module.

OBJECT-TYPE

The serial number of the individual module.

OBJECT-TYPE

The manufacturing date of the individual module.

OBJECT-TYPE

The name of the individual module.

OBJECT-TYPE

The portvlan map of an individual module. The low order bits encode the possible values. The following are the connection paths that exists between the ports on the module: Used on types 69, 72, 81, 83, 84, 86 bit0 - Port 1 to Port 2 bit1 - Port 1 to Backplane Port A bit2 - Port 1 to Backplane Port B bit3 - Port 2 to Backplane Port A bit4 - Port 2 to Backplane Port B bit5 - Backplane Port A to Backplane Port B Used on types 70, 80, 90, 93, 94, 95, 96, 98, 100, 101, 105, 106 bit0 - Port 1 to Port 2 bit1 - Port 1 to Backplane Port A bit2 - Port 1 to Backplane Port B bit3 - Port 2 to Backplane Port A bit4 - Port 2 to Backplane Port B bit5 - Backplane Port A to Backplane Port B bit6 - Port 1 to Mgt bit7 - Port 2 to Mgt bit8 - Backplane A to Mgt bit9 - Backplane B to Mgt Used on types 102, 108, 109, 112 bit0 - Port 1-2-3 interconnect bit1 - Port 1-2-3 to Backplane Port A bit2 - Port 1-2-3 to Backplane Port B bit3 - Backplane Port A to Backplane Port B bit4 - Port 1 to Mgt bit5 - Port 2 to Mgt bit6 - Port 3 to Mgt bit7 - Backplane A to Mgt bit8 - Backplane B to Mgt Used on types 97, 99, 113 bit0 - Port 1 to Port 2 bit1 - Port 1 to Backplane Port A bit2 - Port 1 to Backplane Port B bit3 - Port 2 to Backplane Port A bit4 - Port 2 to Backplane Port B bit5 - Backplane Port A to Backplane Port B bit6 - Port 1 to Mgt bit7 - Port 2 to Mgt bit8 - Backplane A to Mgt bit9 - Backplane B to Mgt Used on types 79, 87 bit0 - Port 1-2-3-4 interconnect bit1 - Port 1-2-3-4 to backplane A bit2 - Port 1-2-3-4 to backplane B bite 3 Backplane A to Backplane B Used on type 103 bit0 - Port A to Backplane A bit1 - Port A to Backplane B bit2 - Port B to Backplane A bit3 - Port B to Backplane B bit4 - Port A to Port B

OBJECT-TYPE

The module's extended features bits. The bit definitions are: bit0 - module is capable of being field upgradeable bit1 - module supports MIB Statistics bit2 - module supports Memory I/O extended registers bit3 - module supports Tag Vlan feature bit4 - module configured as Secure Slave bit5 - module configured as Secure Proxy bit6 - module configured as Secure Master bit7 - module supports 802.3ah OAM Client bit8 - module supports SFP parameters for port1 bit9 - module supports SFP parameters for port2 bit10 - module supports SFP parameters for port3 bit11 - module supports SFP parameters for port4 bit12 - module supports AH event notification bit13 - 1-module redundant power chassis supports contact closure status bit14 - 1-module redundant power chassis supports power over ethernet bit15 - 1-module redundant power chassis RJ45 connector is installed bit16 - 1-module redundant power chassis fan is installed bit17 - when this bit is on the module is a remote slave bit18 - module supports unidirectional on port1 bit19 - module supports unidirectional on port2 bit20 - module supports unidirectional on port3 bit21 - extended power supply bit22 - module supports SNMPv3 bit23 - module is NMM2 capable bit24 - fan is installed bit25 - generic module class supports 802.1ag/Y.1731 bit26 - module GM3 class supports 802.1ag/Y.1731 bit27 - module GM4 class bit28 - port 1 is an XFP port bit29 - port 2 is an XFP port

OBJECT-TYPE

The module's software build number.

OBJECT-TYPE

Enables or disables 802_1q processing. 0 = disable 1 = enable

OBJECT-TYPE

Enables or disables substitution of 802_1q tags. Currently not implemented by any supported module

OBJECT-TYPE

VLAN information is applied to the module and data saved to persistent storage. This variable is a write only.

OBJECT-TYPE

VLAN table for the module Vlan table to be cleared. This variable is a write only.

OBJECT-TYPE

Management module configuration information is applied to the module and data saved to persistent storage. This variable is a write only.

OBJECT-TYPE

8 bits each of PS1 Voltage(msB), PS2 Voltage, Total Voltage and an unused byte(lsB). 1-module redundant power chassis.

OBJECT-TYPE

8 bits each of PS1 Current(msB) (mA/10), PS2 Current, Total Current and an unused byte(lsB). 1-module redundant power chassis.

OBJECT-TYPE

8 bits each of Temperature(msB) .5C/bit and 2 unused byte(lsB). 1-module redundant power chassis.

OBJECT-TYPE

Management module configuration information is restored to factory defaults. This variable is a write only. Different types of restore defaults are supported: restoreFactoryDefaults(0,1) Restores factory defaults restoreLocalDefaults(2) Restores defaults from local file restorePreviousConfig(3) Restores the previously saved configuration. This is useful to regress to a known working setup. restoreFactoryDefaultsKeepIp(4) Restores factory defaults but keeps IP based settings restoreLocalDefaultsKeepIp(5) Restores defaults from local file but keeps IP based settings. restorePreviousConfigKeepIp(6) Restores the previously saved configuration but keeps IP based settings.

OBJECT-TYPE

Enable(1) or disable(0) Core Status Only.

OBJECT-TYPE

Sets the module global policy used to count bytes for bandwidth calculation purposes. This is available on the GM3 & GM4. This is not available on the XM5. 1 = L1 includes all bytes in frame, interframe gap and preamble 2 = L2 includes all bytes in frame, including Layer 2 header and CRC 3 = L3 includes Layer 3 information only, excludes Layer 2 header and CRC

OBJECT-TYPE

Value for service tag.

OBJECT-TYPE

Bit vector for default forwarding map where: bit0 - Port 1 bit1 - Port 2 bit2 - Port 3 bit3 - Port 4 bit4 - Port BPA bit5 - Port BPB

OBJECT-TYPE

The current revision of the FPGA.

OBJECT-TYPE

The expanded part number of the individual module. The modpartnum object indicates the compressed version of the part number name. If this field is not supported in a module it is left as a null length string.

OBJECT-TYPE

The expanded software revision of the individual module. This object allows for an enhanced version of the software revision that include a major and minor component. Major and Minor are always numeric values while the rev value can be a number or an alpha. For instance: 1.0, 1.1, 3.2A, 1.1.2. The two digit modsoftrev object includes the major and minor revision. A modsoftrev of '32' would be shown in this object as '3.2'. This object allows the minor number to be expanded beyond a single digit as shown above by '3.2A' above, even though modsoftrev would be '32'. The modswbuildnum is independent of this scheme, but the complete revision is sometimes referred together as a concatenated value. For instance is '3.2A' is the sofware rev and '1234' is the build number, the concatenated value is '3.2A.1234'.

OBJECT-TYPE

This object is the expanded LED status of the individual module. This object reflects the state, color, and blinking rate of each individual LED. Each LED is represented by a single octet. The first octet in the string is the first LED, the second octet in the string is the second LED, until the last LED. The length of the object indicates the number of LEDs of the modules. Non-installed (missing) LEDs return a value of all zeros. Each octet is encoded in the following way: Bits 0:1 indicate the LED color and state 0x0 = LED is off 0x1 = LED is amber 0x2 = LED is green 0x3 = LED is both amber and green (red) Bits 2:4 indicate the LED blinking frequency 0x0 = LED is solid 0x1 = LED is blinking at 10 Hz 0x2 = LED is blinking at 5 Hz 0x3 = LED is blinking at 2 Hz 0x4 = LED is blinking at 1 Hz 0x5 = LED is blinking at 1/2 Hz Bits 5:7 are currently undefined and return 0x0 for this product revision.

OBJECT-TYPE

The current hardware revision of the module.

OBJECT-TYPE

The current PCB revision of the module.

OBJECT-TYPE

This is a table of the management module configuration variables.

OBJECT-TYPE

Chassis modules.

OBJECT-TYPE

This variable provides the status for a management module's ability to make changes to the system. In backplane slave, a management module cannot make system modification. Modifications must be performed from a management module acting as a backplane master. 0 = read only (can only view configuration settings) 1 = read-write (can view and modify configuration settings).

OBJECT-TYPE

This variable provides the date and time in display format: nn/dd/yyyy hh:mm:ss where nn = 2 digit month, dd = 2 digit day, yyyy = 4 digit year hh - 2 digit hour 0-23, mm = 2 digit minutes 0-59, ss = 2 digit secs 0-59

OBJECT-TYPE

MAC address of the management module

OBJECT-TYPE

IP of the management module

OBJECT-TYPE

subnetmask for the management module

OBJECT-TYPE

IP address for the gateway the management module will use.

OBJECT-TYPE

SNMP read community name.

OBJECT-TYPE

SNMP set community name.

OBJECT-TYPE

NMMs chassis number.

OBJECT-TYPE

Management Modules chassis name. For the M2 modules the max size is 32 octets. For the GM3, GM4, XM5 the max size is 64 octets when a module is accessed directly through the serial port, or via its own IP address for Telnet, SSH, or SNMP. For the GM3, GM4, XM5 when the object is indirectly accessed via the backplane, through IP-less, or through 802.3ah peer-to-peer the value is truncated to 32 bytes.

OBJECT-TYPE

NMMs traphost1 IP address.

OBJECT-TYPE

NMMs traphost2 IP address.

OBJECT-TYPE

NMMs traphost3 IP address.

OBJECT-TYPE

NMMs traphost4 IP address.

OBJECT-TYPE

NMMs traphost5 IP address.

OBJECT-TYPE

NMMs traphost6 IP address.

OBJECT-TYPE

NMMs traphost7 IP address.

OBJECT-TYPE

NMMs traphost8 IP address.

OBJECT-TYPE

Management Modules system location. For the M2 modules the max size is 32 octets. For the GM3, GM4, XM5 the max size is 64 octets when a module is accessed directly through the serial port, or via its own IP address for Telnet, SSH, or SNMP. For the GM3, GM4, XM5 when the object is indirectly accessed via the backplane, through IP-less, or through 802.3ah peer-to-peer the value is truncated to 32 bytes.

OBJECT-TYPE

Management Modules system Contact information. For the M2 modules the max size is 32 octets. For the GM3, GM4, XM5 the max size is 64 octets when a module is accessed directly through the serial port, or via its own IP address for Telnet, SSH, or SNMP. For the GM3, GM4, XM5 when the object is indirectly accessed via the backplane, through IP-less, or through 802.3ah peer-to-peer the value is truncated to 32 bytes.

OBJECT-TYPE

NMMs serial interface password.

OBJECT-TYPE

NMMs telnet interface password.

OBJECT-TYPE

NMMs ftp password.

OBJECT-TYPE

This the interval used by the NMM to send out keep alive traps.

OBJECT-TYPE

Management module VLAN tagged packet ID.

OBJECT-TYPE

This variable defines the baud rate for the serial interface to the NMM. Where: 1 = 300 bps 2 = 1200 bps 3 = 2400 bps 4 = 4800 bps 5 = 9600 bps 6 = 19200 bps 7 = 38400 bps 8 = 57600 bps 9 = 115200 bps

OBJECT-TYPE

This variable defines which special functions are enabled at the NMM. Where: 0x01 = Keep Alive trap enabled 0x02 = Telnet enabled 0x04 = FTP enabled 0x08 = switch reload enabled 0x10 = VLAN enabled 0x20 = sw1 block enabled 0x40 = DHCP client enabled 0x80 = Trap 99 processing enabled

OBJECT-TYPE

This variable defines whether the SNMP Agent is enabled at the NMM. Where: 00 = SNMP disabled 01 = SNMP enabled

OBJECT-TYPE

This variable defines the state of the configuration changes made to the NMM. Where: 0x00 = No changes 0x02 = Changes Pending (not saved in Flash) 0x04 = Saved in Flash, Pending NMM reboot

OBJECT-TYPE

This variable defines the mode the Management module will operate in when configured for SECURE COMMUNICATIONS. Where: 0x00 = No Secure Communications 0x01 = Secure Proxy 0x02 = Secure Slave 0x03 = Secure Master

OBJECT-TYPE

This variable returns the secure connection state between the proxy and secure slave. Where: 0x00 = Not connected 0x01 = Connection Pending 0x02 = Connection established 0x03 = Connection terminating

OBJECT-TYPE

This variable defines whether the IP protocol is active or disabled. 0 = Active 1 = Disabled

OBJECT-TYPE

This variable defines the configuration value for IP protocol's desired state. 0 = ipActive 1 = ipDisabled

OBJECT-TYPE

Management module VLAN tagged packet priority.

OBJECT-TYPE

Permit SNMP SET operations.

OBJECT-TYPE

voltage input to cpu.

OBJECT-TYPE

Voltage out from the cpu.

OBJECT-TYPE

The ambient temperature of the CPU.

OBJECT-TYPE

The slot number of the secure slave in the remote chassis when configured for SECURE COMMUNICATIONS.

OBJECT-TYPE

IP of the management module as assigned by a DHCP server

OBJECT-TYPE

subnetmask of the management module as assigned by a DHCP server

OBJECT-TYPE

Gateway IP address of the management module as assigned by a DHCP Server

OBJECT-TYPE

This variable configures the protocol the Management module will use to communicate with remote chassis when operating in secure mode. Where: 0x01 = (OAM_OFF) No Secure Communications protocol 0x02 = (Auto SECURE_OAM) Use OST proprietary protocol, force remote to switch if not in the OAM_OFF mode 0x03 = (Auto AH_OAM) Use AH protocol, force remote to switch if not in the OAM_OFF mode 0x04 = (SECURE_OAM) Use OST proprietary protocol, remote is not forced to switch and must match modes to connect 0x05 = (AH_OAM) Use AH protocol, remote is not forced to switch and must match modes to connect

OBJECT-TYPE

Value for customer tag.

OBJECT-TYPE

Value for service tag.

OBJECT-TYPE

Controls whether the module is operating as a Cnode.

OBJECT-TYPE

Cnode CIR Where: 1 = 64 Kbps 2 = 128 Kbps 3 = 192 Kbps

OBJECT-TYPE

This variable defines whether the SNMPv3 Agent is enabled at the NMM. Where: 00 = SNMP disabled 01 = SNMP enabled

OBJECT-TYPE

This variable defines whether the module should be allowed to make configurations to itself when in the chassis slave mode. Where: 00 = slaveWrite disabled 01 = slaveWrite enabled

OBJECT-TYPE

This variable defines which version of SNMP traps are supported, where: 1 = SNMPv1 traps 2 = SNMPv2c traps 3 = SNMPv3 traps

OBJECT-TYPE

Capablility bits for this management module.

OBJECT-TYPE

This variable defines whether the module should be allowed to transmit traps out ethernet ports eventhough it is not a chassis master. Where: 00 = slaveTraps disabled 01 = slaveTraps enabled

OBJECT-TYPE

This variable defines whether the module should be allowed to forward traps to the chassis master when module is a chassis slave. Default is forward. Where: 00 = slaveTrapsForward disabled 01 = slaveTrapsForward enabled

OBJECT-TYPE

IP 2 of the management module

OBJECT-TYPE

subnetmask 2 for the management module

OBJECT-TYPE

IP address for the gateway 2 the management module will use.

OBJECT-TYPE

*** This object is deprecated *** EVC associated with ipaddr 1.

OBJECT-TYPE

*** This object is deprecated *** EVC associated with ipaddr 2.

OBJECT-TYPE

Enable or disable BOOTP.

OBJECT-TYPE

Enable or disable TFTP.

OBJECT-TYPE

TFTP server IP address.

OBJECT-TYPE

TFTP Server IP address as assigned by a DHCP Server

OBJECT-TYPE

Selects the TFTP file name.

OBJECT-TYPE

Sets the module Mode Type to normal, AP, or SP.

OBJECT-TYPE

Sets the DHCP port number. 2 port module: 1=None, 2=Port 1, 3=Port 2, 4=BP A, 5=BP B 3 port module: 1=None, 2=Port 1, 3=Port 2, 4=Port 3, 5=BP A, 6=BP B 5 ports and higher modules: 1=None, 2..n+1 = Port 1..n

OBJECT-TYPE

Sets the DHCP Tag VLAN ID.

OBJECT-TYPE

Selects the trap source address, IP1(1) or IP2(2).

OBJECT-TYPE

This object when written sets the Mux Grouping defaults for a management module. When read the value always returns 'false'. Writing this sets the Mux Group EVC and bandwidth profile configurations.

OBJECT-TYPE

This object enables forwarding of managment traffic from the selected ports only for M2 modules only. Management traffic from ports not defined is dropped. all(0) Management traffic forwarded from all ports port1(1) Management traffic forwarded from Port 1 only port2(2) Management traffic forwarded from Port 2 only backplaneA(3) Management traffic forwarded from BP A only backplaneB(4) Management traffic forwarded from BP B only

OBJECT-TYPE

This object enables forwarding of managment traffic from the selected ports only for M3, M4, and M5 modules only. Management traffic from ports not defined is dropped.

OBJECT-TYPE

This a table of Ports per module. There are as many entries as specified by modnumports in the moduleEntry

OBJECT-TYPE

Ports per module table.

OBJECT-TYPE

Used to get or set state of port.

OBJECT-TYPE

Used to get or set state of port.

OBJECT-TYPE

Used to get or set the port throughput limit selection. The following are the limits are enforced by module type: Used on types 80, 96, 70, 90, 86, 84, 87 (lower limit=0, upper limit=7) where: 0 = 100 Mbps 1 = 128 kbps 2 = 256 kbps 3 = 512 kbps 4 = 1 Mbps 5 = 2 Mbps 6 = 4 Mbps 7 = 8 Mbps Used on types 100, 101 (lower limit=1, upper limit=20) where: 1 = 64 kbps 2 = 128 kbps 3 = 256 kbps 4 = 512 kbps 5 = 768 kbps 6 = 1 Mbps 7 = 2 Mbps 8 = 3 Mbps 9 = 4 Mbps 10 = 5 Mbps 11 = 6 Mbps 12 = 7 Mbps 13 = 8 Mbps 14 = 9 Mbps 15 = 10 Mbps 16 = 20 Mbps 17 = 30 Mbps 18 = 40 Mbps 19 = 50 Mbps 20 = 100 Mbps Used on types 105, 106 (lower limit=1, upper limit=33) 1 = 64 kbps 2 = 128 kbps 3 = 256 kbps 4 = 512 kbps 5 = 768 kbps 6 = 1 Mbps 7 = 2 Mbps 8 = 3 Mbps 9 = 4 Mbps 10 = 5 Mbps 11 = 6 Mbps 12 = 7 Mbps 13 = 8 Mbps 14 = 9 Mbps 15 = 10 Mbps 16 = 20 Mbps 17 = 30 Mbps 18 = 40 Mbps 19 = 50 Mbps 20 = 60 Mbps 21 = 70 Mbps 22 = 80 Mbps 23 = 90 Mbps 24 = 100 Mbps 25 = 200 Mbps 26 = 300 Mbps 27 = 400 Mbps 28 = 500 Mbps 29 = 600 Mbps 30 = 700 Mbps 31 = 800 Mbps 32 = 900 Mbps 33 = 1000 Mbps Types 97, 99, 102, 108, 109, 112, 113 use numeric values in kpbs with a lower limit of 64 and an upper limit of 1,000,000. Types not listed have no limit.

OBJECT-TYPE

Used to get or set port user-priority.

OBJECT-TYPE

Used to get or set port cfi. Currently not used and defaulted to 0

OBJECT-TYPE

Used to get or set port VID.

OBJECT-TYPE

Used to get or set port membership criteria.

OBJECT-TYPE

Used to get or set port ingress security.

OBJECT-TYPE

Used to get or set port egress policy.

OBJECT-TYPE

Used to get or set the port throughput limit selection. The following are the limits are enforced by module type: Used on types 80, 96, 70, 90, 86, 84, 87 (lower limit=0, upper limit=7) where: 0 = 100 Mbps 1 = 128 kbps 2 = 256 kbps 3 = 512 kbps 4 = 1 Mbps 5 = 2 Mbps 6 = 4 Mbps 7 = 8 Mbps Used on types 100, 101 (lower limit=64, upper limit=100,000) Values are number of kbps per second, i.e. rate = value x 1000, units in bps Used on types 97, 99, 102, 105, 106, 108, 109, 112, 113 (lower limit=64, upper limit=1,000,000) Values are number of kbps per second, i.e. rate = value x 1000, units in bps Types not listed have no limit.

OBJECT-TYPE

Used to get the port speed. 0 = undefined 1 = speed10Mbps 2 = speed100Mbps 3 = speed1Gbps 4 = speed10Gbps

OBJECT-TYPE

Used to get/set the unidirectional support. 0 = uniDisabled 1 = uniEnabled

OBJECT-TYPE

Used to get/set behavior on overflow. 0 = undefined 1 = inDrop 2 = inPause

OBJECT-TYPE

Used to get or set the port throughput limit selection.

OBJECT-TYPE

Used to get or set the port L2Cp processing method. 0 = undefined 1 = inDrop 2 = inForward 3 = inTunnel

OBJECT-TYPE

Used to get or set the port egress QoS Policy. 0 = undefined 1 = fairWeight 2 = starving

OBJECT-TYPE

Used to get or set the port access type. 0 = undefined 1 = tunnel 2 = access 3 = trunk

OBJECT-TYPE

Used to clear the statistics table for this port

OBJECT-TYPE

Reports the link state of the port. 0 = No link 1 = Linked

OBJECT-TYPE

The object indcates the linked port duplex mode. undefined(0) Port is not linked or state of duplex is unknown halfDuplex(1) Port is linked at half duplex fullDuplex(2) Port is linked at full duplex

OBJECT-TYPE

MAC address of the port. If a MAC address doesn't exist on a port the value returned is all zeros.

OBJECT-TYPE

This a table of Statistics per port.

OBJECT-TYPE

extended module statitical information.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - Object name explains its usage.

OBJECT-TYPE

Statistics counter - packets of octet count in object name.

OBJECT-TYPE

Statistics counter - packets of octet count in object name.

OBJECT-TYPE

Statistics counter - packets of octet count in object name.

OBJECT-TYPE

Statistics counter - packets of octet count in object name.

OBJECT-TYPE

Statistics counter - packets of octet count in object name.

OBJECT-TYPE

Statistics counter - packets of octet count in object name.

OBJECT-TYPE

64 bit octet transmission counter.

OBJECT-TYPE

64 bit octet receive counter.

OBJECT-TYPE

This a table of VLAN entries per module. There is a maximum of 64 valid entries in the table

OBJECT-TYPE

VLAN module table.

OBJECT-TYPE

Used to get or set elements in the vlan table entry.

OBJECT-TYPE

Used to set or delete a VLAN table entry. 0 = entry does not exists or is to be deleted, 1 = entry to be created or re-activated (in the case the entry was modified, the module needs to be notified of the change. This would constitute a re-activation.

OBJECT-TYPE

Used to set or get the vlan identifier. valid settable range is 0-4095

OBJECT-TYPE

Used to set or get the port's membership in the specified vlan. 0 = not a member 1 = include in membership

OBJECT-TYPE

Used to set or get the port's membership in the specified vlan. 0 = not a member 1 = include in membership

OBJECT-TYPE

Used to set or get the port's membership in the specified vlan. 0 = not a member 1 = include in membership

OBJECT-TYPE

Used to set or get the port's membership in the specified vlan. 0 = not a member 1 = include in membership

OBJECT-TYPE

Used to set or get the port's membership in the specified vlan. 0 = not a member 1 = include in membership

OBJECT-TYPE

Used to set or get the port's membership in the specified vlan. 0 = not a member 1 = include in membership

OBJECT-TYPE

This is a table of AH parameter entries per port.

OBJECT-TYPE

AH port table.

OBJECT-TYPE

Used to get or set the state of the AH protocol over specified port. 0 = disable - this port is not actively using the AH protocol 1 = enabled - this port is actively using the AH protocol

OBJECT-TYPE

Used to get or set the state of the OAM remote loopback. 0 = off - remote loopback is not active 1 = on - remote loopback has been activated

OBJECT-TYPE

Used to get or set the mode AH OAM Client. 0 = PASSIVE - Does not initiate discovery or remote loopbacks 1 = ACTIVE - Initiates discovery process and may initiate remote loopbacks 2 = PASSIVE, PROTECTED - Same as PASSIVE but disallows configuration requests from link partner using AH extensions 3 = ACTIVE, PROTECTED - Same as ACTIVE but disallows configuration requests from link partner using AH extensions

OBJECT-TYPE

Used to get or set the mode AH OAM Client. 0 = PASSIVE - Does not initiate discovery or remote loopbacks 1 = ACTIVE - Initiates discovery process and may initiate remote loopbacks 2 = PASSIVE, PROTECTED - Same as PASSIVE but disallows configuration requests from link partner using AH extensions 3 = ACTIVE, PROTECTED - Same as ACTIVE but disallows configuration requests from link partner using AH extensions

OBJECT-TYPE

Used to get local multiplexer state. 0 = FWD - Multiplexer passes MAC client frames to subordinate sublayer 1 = DISCARD - Multiplexer discards MAC client frames

OBJECT-TYPE

Used to get remote multiplexer state. 0 = FWD - Multiplexer passes MAC client frames to subordinate sublayer 1 = DISCARD - Multiplexer discards MAC client frames

OBJECT-TYPE

Used to get local parser state. 0 = FWD - Parser passes received non-OAMPDUs to subordinate sublayer 1 = LOOPBACK - Parser passes received non-OAMPDUs to Multiplexer during remote loopback test 2 = DISCARD - Parser discards received non-OAMPDUs

OBJECT-TYPE

Used to get remote parser state. 0 = FWD - Parser passes received non-OAMPDUs to subordinate sublayer 1 = LOOPBACK - Parser passes received non-OAMPDUs to Multiplexer during remote loopback test 2 = DISCARD - Parser discards received non-OAMPDUs

OBJECT-TYPE

Used to get local configured features supported in bit encoded value. where: bit0 = OAM Mode bit1 = Unidirectional support bit2 = Loopback Support bit3 = interprets link events bit4 = Variable Retrieval bit5 = Critical Event

OBJECT-TYPE

Used to get Link Event status in bit encoded value. where: bit0 = Link Fault bit1 = Dying Gasp bit2 = Critical Event bit3 = Local Evaluating bit4 = Local Stable bit5 = Remote Evaluating bit6 = Remote Stable

OBJECT-TYPE

Used to get/set Remote Loopback timeout. Value is in seconds with range 0 - 300.

OBJECT-TYPE

Used to get remote configured features supported in bit encoded value. where: bit0 = OAM Mode bit1 = Unidirectional support bit2 = Loopback Support bit3 = interprets link events bit4 = Variable Retrieval bit5 = Critical Event

OBJECT-TYPE

Used to get Link Event status in bit encoded value. bit0 = Link Fault bit1 = Dying Gasp bit2 = Critical Event bit3 = Local Evaluating bit4 = Local Stable bit5 = Remote Evaluating bit6 = Remote Stable

OBJECT-TYPE

Used to get/set Remote Loopback timeout. Value is in seconds with range 0 - 300.

OBJECT-TYPE

Used to get the Organizational Unique ID of the local port.

OBJECT-TYPE

Used to get the Organizational Unique ID of the remote port.

OBJECT-TYPE

Used to get or set errored symbol period window for the local port.

OBJECT-TYPE

Used to get or set errored symbol period threshold for the local port.

OBJECT-TYPE

Used to get or set the errored symbol window for the local port.

OBJECT-TYPE

Used to get or set the errored symbol threshold for the local port.

OBJECT-TYPE

Used to get or set the errored frame period window for the local port.

OBJECT-TYPE

Used to get or set the errored frame period threshold for the local port.

OBJECT-TYPE

Used to get or set the errored frame seconds window for the local port.

OBJECT-TYPE

Used to get or set the errored frame seconds threshold for the local port.

OBJECT-TYPE

Used to get the port number of the remote partner. Value is in the Range 1-5. A zero port number indicates no connection or not supported

OBJECT-TYPE

This object indicates the 802.3ah Symbol Error Running Total value from the last OAM sublayer reset or clear operation. A value of zero indicates that no symbol errors have been detected since the last reset or clear. For each symbol error detected the value of the object increments.

OBJECT-TYPE

This object indicates the number of 802.3ah Errored Symbol Period Event TLVs that have been generated since the OAM sublayer was reset or the counters have been cleared. A value of zero indicates that no Errored Symbol Period Event TLVs have been generated. For each Errored Symbol Period Event TLV generated the value of the object increments.

OBJECT-TYPE

This object indicates the sum of the 802.3ah errored frames that have been detected since the OAM sublayer was reset or clear operation. A value of zero indicates that no errored frames have been detected since the last reset or clear. For each errored frame the value of the object increments.

OBJECT-TYPE

This object indicates the number of 802.3ah Errored Frame Event TLVs that have been generated since the OAM sublayer was reset or the counters have been cleared. A value of zero indicates that no Errored Frame Event TLVs have been generated. For each Errored Frame Event Event TLV generated the value of the object increments.

OBJECT-TYPE

This object indicates the sum of 802.3ah the frame errors that have been detected that have been since the OAM sublayer was reset or clear operation. A value of zero indicates that no errored frames have been detected since the last reset or clear. For each errored frame the value of the object increments.

OBJECT-TYPE

This object indicates the number of 802.3ah Errored Frame Period Event TLVs that have been generated since the OAM sublayer was reset or the counters have been cleared. A value of zero indicates that no Errored Frame Period Event TLVs have been generated. For each Errored Symbol Period Event TLV generated the value of the object increments.

OBJECT-TYPE

This object indicates the sum of the 802.3ah errored frame seconds that have been detected that have been since the OAM sublayer was reset or clear operation. A value of zero indicates that no errored frame seconds have been detected since the last reset or clear. For each errored frame the value of the object increments.

OBJECT-TYPE

This object indicates the number of 802.3ah Errored Frame Seconds Summary Event TLVs that have been generated since the OAM sublayer was reset or the counters have been cleared. A value of zero indicates that no Errored Frame Seconds Summary Event TLVs have been generated. For each Errored Symbol Period Event TLV generated the value of the object increments.

OBJECT-TYPE

This object when written clears the 802.3ah statistic counters associated with a specific port. When read the value always returns 'false'. Writing this value does not change any items in the configuration table.

OBJECT-TYPE

This object sets maximum 802.3ah PDU transmission rate. The default value is 10 (10 frames per second)

OBJECT-TYPE

Used to get or set the state of the local critical event mode. 0 = local critical events not enabled 1 = local critical events are enabled

OBJECT-TYPE

Used to the SNMP traps which will cause the generation of a local critical event. It is a list of zero or more trap numbers separated by a comma or range, '..'. Example values: 5 5,110,112 100..110 5,110,90..95,100..105 The default value is an emtpy string, no SNMP traps generate a local critical event.

OBJECT-TYPE

This is a table of AH parameter entries per port.

OBJECT-TYPE

SFP port table.

OBJECT-TYPE

Used to get present or absence of SFP device. 0 = undefined 1 = notPresent 2 = present

OBJECT-TYPE

Used to get SFP device EEPROM address A0

OBJECT-TYPE

Used to get SFP device EEPROM address A2

OBJECT-TYPE

SFP Bitrate in Mbps

OBJECT-TYPE

SFP Vendor Name

OBJECT-TYPE

SFP Vendor Name

OBJECT-TYPE

SFP Serial Number

OBJECT-TYPE

SFP Date Code

OBJECT-TYPE

SFP tempearture in degrees Centigrade

OBJECT-TYPE

SFP VCC in volts

OBJECT-TYPE

SFP Bias Current in millamps

OBJECT-TYPE

SFP Transmission power in dBm

OBJECT-TYPE

SFP Transmission power in dBm

OBJECT-TYPE

This is a table of SNMPv3 users.

OBJECT-TYPE

User table entry.

OBJECT-TYPE

User table index

OBJECT-TYPE

SNMPv3 user name.

OBJECT-TYPE

SNMPv3 security level 0 = undefined 1 = no authentication/no privacy 2 = authentication/no privacy 3 = authentication/privacy

OBJECT-TYPE

SNMPv3 user authentication password.

OBJECT-TYPE

SNMPv3 user privacy password.

OBJECT-TYPE

SNMPv3 User Type 0 = undefined 1 = admin 2 = read-write 3 = read-only 4 = deny

OBJECT-TYPE

This table supports the Serial, Telnet, FTP user session status.

OBJECT-TYPE

This is a user protocol table entry.

OBJECT-TYPE

An index that is used to identify a specific user protocol session. The index should remain constant until the session is closed.

OBJECT-TYPE

This object indicates the specific user protocol session identity state. serial (1) User protocol session type is the serial port telnet (2) User protocol session type is TELNET ftp (3) User protocol session type is FTP

OBJECT-TYPE

This object indicates the status of the specific user protocol session state. inactive(1) User is currently inactive (reserved value, not used) active(2) User is currently authenticated and active lockedout(3) User is currently locked out for authentication and cannot become active until the locked out timeout expires and the user status goes back to idle.

OBJECT-TYPE

This object indicates the status of the specific user protocol session state. It is not applicable to the 'serial' interface or to a session type that is locked out. In these cases the object is returned with a value of 'notDefined'. notDefined(1) Management port is unknown or undefined mgt1(2) Management Port 1 association mgt2(3) Management Port 2 association

OBJECT-TYPE

This object indicates the IP address of the specific user protocol session. It is not applicable to the 'serial' interface or to a session type that is locked out. In these cases this object is returned as '0.0.0.0'.

OBJECT-TYPE

The object indicates the time a specific user protocol session has been open or is locked out, in 0.01 seconds, based upon the value of ostProtocolStatusState.

OBJECT-TYPE

This table supports the module environmental status objects.

OBJECT-TYPE

This is an environmental table entry.

OBJECT-TYPE

This object indicates the status of Power Supply PS1 or PSA. notApplicable(0) Power Supply PS1/PSA is not supported notInstalled(1) Power Supply PS1/PSA is not installed installedNotPowered(2) Power Supply PS1/PSA is installed, but not powered installedPowered(3) Power Supply PS1/PSA is installed and powered

OBJECT-TYPE

This object indicates PS1/PSA voltage input in millivolts. A value of zero indicates that no voltage is applied or the power supply is incapable of supplying a voltage input reading.

OBJECT-TYPE

This object indicates PS1/PSA voltage output in millivolts. A value of zero indicates that no voltage is output or the power supply is incapable of supplying a voltage output reading.

OBJECT-TYPE

This object indicates PS1/PSA current output in millianmps. A value of zero indicates that no current is output or the power supply is incapable of supplying a current output reading.

OBJECT-TYPE

This object indicates the status of Power Supply PS2 or PSB. notApplicable(0) Power Supply PS2/PSB is not supported notInstalled(1) Power Supply PS2/PSB is not installed installedNotPowered(2) Power Supply PS2/PSB is installed, but not powered installedPowered(3) Power Supply PS2/PSB is installed and powered

OBJECT-TYPE

This object indicates PS2/PSB voltage input in millivolts. A value of zero indicates that no voltage is applied or the power supply is incapable of supplying a voltage input reading.

OBJECT-TYPE

This object indicates PS2/PSB voltage output in millivolts. A value of zero indicates that no voltage is output or the power supply is incapable of supplying a voltage output reading.

OBJECT-TYPE

This object indicates PS2/PSB current output in millianmps. A value of zero indicates that no current is output or the power supply is incapable of supplying a current output reading.

OBJECT-TYPE

This object indicates the module internal ambient temperature in degrees centigrade. A value of zero indicates that the current temperature is 0 degrees or the module incapable of supplying a temperature reading.

OBJECT-TYPE

This object indicates the status of Fan 1. notApplicable(0) Fan 1 is not supported notInstalled(1) Fan 1 is not installed installedNotPowered(2) Fan 1 is installed, but not powered installedPowered(3) Fan 1 is installed and powered

OBJECT-TYPE

This object indicates the speed of Fan 1 in RPM (revolutions per minute) A value of zero indicates that the current fan speed is 0 RPM or the fan is not supported or installed.

OBJECT-TYPE

This object indicates the status of Fan 2. notApplicable(0) Fan 2 is not supported notInstalled(1) Fan 2 is not installed installedNotPowered(2) Fan 2 is installed, but not powered installedPowered(3) Fan 2 is installed and powered

OBJECT-TYPE

This object indicates the speed of Fan 2 in RPM (revolutions per minute) A value of zero indicates that the current fan speed is 0 RPM or the fan is not supported or installed.

OBJECT-TYPE

This object indicates the status of Fan 3. notApplicable(0) Fan 3 is not supported notInstalled(1) Fan 3 is not installed installedNotPowered(2) Fan 3 is installed, but not powered installedPowered(3) Fan 3 is installed and powered

OBJECT-TYPE

This object indicates the speed of Fan 3 in RPM (revolutions per minute) A value of zero indicates that the current fan speed is 0 RPM or the fan is not supported or installed.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY