NETGEAR-SMART-SWITCHING-MIB

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0' When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports.

TEXTUAL-CONVENTION

This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.

TEXTUAL-CONVENTION

This data type is used to model IPv6 address interface identifiers. This is a binary string of up to 8 octets in network byte-order.

TEXTUAL-CONVENTION

This data type is used to model IPv6 address prefixes. This is a binary string of up to 16 octets in network byte-order.

TEXTUAL-CONVENTION

A unique value, greater than zero for each internetwork-layer interface in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each internetwork-layer interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.

TEXTUAL-CONVENTION

This textual convention is an extension of the Ipv6IfIndex convention. The latter defines a greater than zero value used to identify an IPv6 interface in the managed system. This extension permits the additional value of zero. The value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced.

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered vlan, and the least significant bit represents the highest numbered vlan. Thus, each vlan supported is represented by a single bit within the value of this object. If that bit has a value of '1' then the associated port is in that vlan; the port is not included if the vlans bit has a value of '0'.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The switch's Inventory system description.

OBJECT-TYPE

Type of the Machine used in the Switch

OBJECT-TYPE

The switch's Machine Model.

OBJECT-TYPE

Serial number of the switch.

OBJECT-TYPE

FRU Number of the switch

OBJECT-TYPE

The switch's Inventory Maintenance Level

OBJECT-TYPE

The switch's Inventory Part Number

OBJECT-TYPE

Name of the Manufacturer of this unit

OBJECT-TYPE

Burned-In MAC Address

OBJECT-TYPE

Operating System running on this unit

OBJECT-TYPE

Network Processing Device for this unit

OBJECT-TYPE

Lists additional functional packages available on this unit.

OBJECT-TYPE

Lists the version of software loaded on this unit.

OBJECT-IDENTITY

OBJECT-TYPE

The total number of traps sent since last reset.

OBJECT-TYPE

The number of traps sent since last viewed.

OBJECT-TYPE

Agent Trap Log

OBJECT-TYPE

Agent trap log entry

OBJECT-TYPE

Unique index of trap entry

OBJECT-TYPE

System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.

OBJECT-TYPE

Description of the trap sent.

OBJECT-TYPE

Supported MIB table

OBJECT-TYPE

Supported MIB entry

OBJECT-TYPE

Unique index of the Supported MIB entry

OBJECT-TYPE

The name of the MIB (RFC or IEEE) that is supported.

OBJECT-TYPE

Description of the MIB (RFC or IEEE) that is supported.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table of the switch's login session

OBJECT-TYPE

Login Session Entry

OBJECT-TYPE

Agent Login Session Index of the switch

OBJECT-TYPE

Agent Login Session UserName of the switch

OBJECT-TYPE

Agent Login Session IP Address of the switch

OBJECT-TYPE

Agent Login Session Connection Type of the switch

OBJECT-TYPE

Agent Login Session Idle Time of the switch

OBJECT-TYPE

Agent Login Session Time of the switch

OBJECT-TYPE

Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.

OBJECT-TYPE

Type of address agentLoginSessionInetAddress is returning. Can be either unknown(0), ipv4(1), or ipv6 (2). Will return unknown(0) in the case of a serial login.

OBJECT-TYPE

Inet Address of the connecting the user is logging in with. Will return a zero-length string in the case of a serial login.

OBJECT-IDENTITY

OBJECT-TYPE

Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 1 to 160. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.

OBJECT-TYPE

Maximum number of Telnet Sessions Config telnet maxsessions is an integer value from 0 to 5 that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.

OBJECT-TYPE

Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.

OBJECT-IDENTITY

OBJECT-TYPE

Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).

OBJECT-TYPE

User Config Table

OBJECT-TYPE

User Config Entry

OBJECT-TYPE

Agent User Config Index

OBJECT-TYPE

Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters).

OBJECT-TYPE

Agent User Password This object will return an empty string even if a password is set.

OBJECT-TYPE

Agent User Access Mode

OBJECT-TYPE

SNMPv3 User Authentication. The user passsword must be set to a string greater than or equal to 8 characters for this to be set to anything but none(1). none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication

OBJECT-TYPE

SNMPv3 User Encryption Can not be set to des(2) if agentUserAuthenticationType is set to none(1). none(1) - no encryption used des(2) - DES encryption used

OBJECT-TYPE

SNMPv3 User Encryption Password This object will return an empty string even if a password is set. agentUserEncryptionType must be set to des(2) before this object can be configured. This object will return an empty string even if a password is set.

OBJECT-TYPE

Displays whether the user account is locked due to excessive failed login attempts.

OBJECT-TYPE

Date and time when the user's password expires (past or present). Only valid when password aging is enabled.

OBJECT-IDENTITY

OBJECT-TYPE

agentSerialTimeout specifies the maximum connect time(in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely. The time range is 0 to 160.

OBJECT-TYPE

agentSerialBaudrate specifies the current baud rate at which the serial port will try to connect. The available values are 1200, 2400, 4800, 9600, 19200, 38400,57600, and 115200 baud.

OBJECT-TYPE

agentSerialCharacterSize specifies the number of bits in a character. The number of bits is always 8.

OBJECT-TYPE

agentSerialHardwareFlowControl specifies whether hardware flow-control is enabled or disabled. Hardware Flow Control is always disabled.

OBJECT-TYPE

agentSerialStopBits specifies the number of Stop bits per character. The number of Stop bits is always 1.

OBJECT-TYPE

agentSerialParityType specifies the Parity Method used on the Serial Port. The Parity Method is always None.

OBJECT-IDENTITY

OBJECT-TYPE

Minimum length for user passwords All new local user passwords must be at least this many characters in length.

OBJECT-TYPE

The number of previous passwords to store for prevention of password reuse. This ensures that each user does not reuse passwords often. A value of 0 indicates that no previous passwords will be stored.

OBJECT-TYPE

The maximum time that user passwords are valid, in days, from the time the password is set. Once a password expires, the user will be required to enter a new password following the first login after password expiration. A value of 0 indicates that passwords never expire.

OBJECT-TYPE

The number of allowable failed local authentication attempts before the user's account is locked. A value of 0 indicates that user accounts will never be locked.

OBJECT-IDENTITY

OBJECT-TYPE

Agent LAG Create. When this object is set with a non-empty string, a new LAG will be created if possible with the entered string as its name.

OBJECT-TYPE

A summary table of the switch's LAG config entries

OBJECT-TYPE

Switch's LAG config entry

OBJECT-TYPE

Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable.

OBJECT-TYPE

Agent LAG Name. The associated name of the LAG used during creation.

OBJECT-TYPE

Agent LAG FlushTimer.

OBJECT-TYPE

Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down.

OBJECT-TYPE

Agent LAG AdminMode. Administratively enables or disables this LAG interface.

OBJECT-TYPE

Agent LAG StpMode If Dot1d is enabled, the valid values are: dot1d(1), fast(2), and off(3) If Dot1s is enabled, the valid values are: off(3) and dot1s(4)

OBJECT-TYPE

Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.

OBJECT-TYPE

Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable.

OBJECT-TYPE

Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG.

OBJECT-TYPE

Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained.

OBJECT-TYPE

Agent LAG Static Capability enable(1) - Static capability is enabled for this LAG interface disable(2) - Static capability is disabled for this LAG interface

OBJECT-TYPE

A detailed table of the switch's LAG config entries

OBJECT-TYPE

Switch's LAG config entry

OBJECT-TYPE

LAG index

OBJECT-TYPE

LAG port index

OBJECT-TYPE

LAG port speed. See agentPortType for a description and list of valid values.

OBJECT-TYPE

LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG.

OBJECT-TYPE

Agent LAG Static Capability. Configures whether Static LAGs are supported on this device.

OBJECT-IDENTITY

OBJECT-TYPE

The switch's network ip address

OBJECT-TYPE

The switch's network subnet mask

OBJECT-TYPE

The switch's network default gateway

OBJECT-TYPE

The switch's network Burned-In MAC address

OBJECT-TYPE

The switch's network locally administered MAC address

OBJECT-TYPE

The switch's network Mac Address Type

OBJECT-TYPE

The switch's network config protocol

OBJECT-TYPE

The switch's network config protocol on next bootup

OBJECT-TYPE

Configures the use of the Java interface through the Web.

OBJECT-TYPE

The VLAN ID through which the switch can be managed using the agentNetworkIPAddress

OBJECT-TYPE

The network port IPv6 administrative state

OBJECT-TYPE

The network port IPv6 Gateway Address

OBJECT-TYPE

The list of IPv6 address prefixes for the network port.

OBJECT-TYPE

An interface entry containing objects of a particular IPv6 address prefix

OBJECT-TYPE

The service port IPv6 Address Prefix

OBJECT-TYPE

The service port IPv6 Address Prefix Length

OBJECT-TYPE

The service port IPv6 Eui Flag

OBJECT-TYPE

OBJECT-IDENTITY

OBJECT-TYPE

The switch's ServicePort ip address

OBJECT-TYPE

The switch's ServicePort subnet mask

OBJECT-TYPE

The switch's ServicePort default gateway

OBJECT-TYPE

The switch's ServicePort Burned-In MAC address

OBJECT-TYPE

The switch's ServicePort config protocol

OBJECT-TYPE

The service port IPv6 administrative state

OBJECT-TYPE

The service port IPv6 Gateway Address

OBJECT-TYPE

The list of IPv6 address prefixes for the service port.

OBJECT-TYPE

An interface entry containing objects of a particular IPv6 address prefix

OBJECT-TYPE

The service port IPv6 Address Prefix

OBJECT-TYPE

The service port IPv6 Address Prefix Length

OBJECT-TYPE

The service port IPv6 Eui Flag

OBJECT-TYPE

OBJECT-IDENTITY

OBJECT-TYPE

Creates a new SNMP Community entry. Defaults: IPAddress 0.0.0.0 IpMask 0.0.0.0 AccessMode read-only Status config

OBJECT-TYPE

A table of the switch's SNMP Config entries

OBJECT-TYPE

Switch's SNMP Config entry

OBJECT-TYPE

The switch's Snmp Community Index

OBJECT-TYPE

The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored.

OBJECT-TYPE

The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.

OBJECT-TYPE

The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255.

OBJECT-TYPE

The switch's Snmp Community Access Mode Access Mode - This value can be read-only or read/write. A community with a read-only access allows for switch information to be displayed. A community with a read/write access allows for configuration changes to be made and for information to be displayed.

OBJECT-TYPE

The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP managers associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent.

OBJECT-TYPE

Creates a new trap receiver entry. Defaults: IPAddress 0.0.0.0 status config

OBJECT-TYPE

Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.

OBJECT-TYPE

Switch's Snmp Trace Receiver Config entry

OBJECT-TYPE

The switch's Snmp Trap Receiver Index

OBJECT-TYPE

The switch's Snmp Trap Receiver Community Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case-sensitive.

OBJECT-TYPE

IP Address - Each IP address parameter is four integer numbers. The numbers range from 0 to 255.

OBJECT-TYPE

The switch's Snmp Trap Reciever Status. active(1) - This trap receiver is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap reciever is not active; no SNMP Traps will be sent to this reciever until it's set back to active(1). config(3) - The trap reciever Status must be set to this value in order to configure it. When creating a new trap receiver entry, the Status will initially be set to this value. Note: agentSnmpTrapReceiverIPAddress must be set to non-zero before changing to active(1) or notInService(2). destroy(4) - Set to this value to remove the trap receiver entry from the agent.

OBJECT-TYPE

The version of trap sent to this Reciever. snmpv1(1) - This will send a SNMPv1 trap. snmpv2c(2) - This will send a SNMPv2c trap.

OBJECT-TYPE

IPv6 Address for SNMP receiver.

OBJECT-IDENTITY

OBJECT-TYPE

Authentication Flag - Enable/Disable authentication Flag.

OBJECT-TYPE

Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.

OBJECT-TYPE

Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session.

OBJECT-TYPE

Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.

OBJECT-TYPE

Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery.

OBJECT-IDENTITY

OBJECT-TYPE

The switch's Spanning Tree Switch Status

OBJECT-IDENTITY

OBJECT-TYPE

The switch's address aging timeout table

OBJECT-TYPE

Aging information about a specific Filtering Database.

OBJECT-TYPE

The FDB entry's address aging timeout (in seconds)

OBJECT-TYPE

The switch's static Mac filtering table

OBJECT-TYPE

Per-port ingress/egress filter configuration based on VLAN Id and MAC address.

OBJECT-TYPE

The Static MAC Filter Vlan Id

OBJECT-TYPE

The Static MAC Filter MAC address

OBJECT-TYPE

The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table. Configuring destination port mask for a unicast MAC filter is not supported on some platforms.

OBJECT-TYPE

The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP/MLD Snooping Global configuration entries.

OBJECT-TYPE

Represents entry for Snooping switch Configuration.

OBJECT-TYPE

The protocol type of network protocol in use.

OBJECT-TYPE

This enables or disables Snooping on the system.

OBJECT-TYPE

IGMP/MLD Snooping Port Mask. This allows configuration of IGMP/MLD Snooping on selected ports. IGMP Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a port which has IGMP Snooping enabled becomes enabled for routing, or is enlisted as a member of a LAG, IGMP Snooping functionality will be disabled on that port. IGMP Snooping functionality will be subsequently be reenabled if routing is disabled or LAG membership is removed from an interface that had previously had IGMP Snooping enabled. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU.

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP Snooping Interface configuration entries.

OBJECT-TYPE

Represents entry for a IGMP Snooping Interface.

OBJECT-TYPE

The port number to be selected. Each port maps to an interface.

OBJECT-TYPE

This enables or disables IGMP Snooping on a selected interface.

OBJECT-TYPE

The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime.

OBJECT-TYPE

The amount of time in seconds a switch will wait after sending a query on the selected interface because it did not receive a report for a particular group in that interface. This value must be less than agentSwitchIGMPSnoopingIntfGroupMembershipInterval.

OBJECT-TYPE

The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of interfaces with multicast routers attached.

OBJECT-TYPE

This enables or disables IGMP Snooping on the selected interface.

OBJECT-TYPE

This enables or disables Multicast Routing on the selected interface.

OBJECT-TYPE

This field lists all the VlanIDs which include the selected interface.

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP Snooping Vlan configuration entries.

OBJECT-TYPE

Represents entry for a IGMP Snooping Vlan.

OBJECT-TYPE

This enables or disables IGMP Snooping on a selected Vlan interface.

OBJECT-TYPE

The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in the vlan from the entry. This value must be greater than agentSwitchIGMPSnoopingIntfMaxResponseTime.

OBJECT-TYPE

The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This value must be less than agentSwitchIGMPSnoopingIntfGroupMembershipInterval.

OBJECT-TYPE

This enables or disables IGMP Snooping on the selected vlan.

OBJECT-TYPE

The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is removed from the list of interfaces with multicast routers attached. This parameter is configurable only for exisiting Vlans.

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP Static Mrouter Configuration parameters.

OBJECT-TYPE

Represents entry for a IGMP Static Mrouter.

OBJECT-TYPE

This enables or disables IGMP Mrouter on a per-interface per-vlan basis.

OBJECT-IDENTITY

OBJECT-TYPE

The Multicast Forwarding Database table

OBJECT-TYPE

Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User.

OBJECT-TYPE

Vlan Index for which this entry is associated with.

OBJECT-TYPE

A multicast MAC address for which the switch has forwarding and or filtering information.

OBJECT-TYPE

The component that is responsible for this entry in the Multicast Forwarding Database.

OBJECT-TYPE

This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol

OBJECT-TYPE

Text description of this multicast table entry.

OBJECT-TYPE

BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

The Multicast Forwarding Database Summary table

OBJECT-TYPE

Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address.

OBJECT-TYPE

Vlan Index for which this entry is associated with.

OBJECT-TYPE

A multicast MAC address for which the switch has forwarding and or filtering information.

OBJECT-TYPE

Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table.

OBJECT-TYPE

This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark.

OBJECT-TYPE

This displays the current number of entries in the Multicast Forwarding Database table.

OBJECT-IDENTITY

OBJECT-TYPE

Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports.

OBJECT-TYPE

The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the broadcast traffic.

OBJECT-TYPE

Configures the broadcast storm recovery threshold for this port as a percentage of port speed.

OBJECT-TYPE

The switch config multicast allows you to enable or disable multicast storm recovery mode. When you specify Enable for multicast Storm Recovery and the multicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the multicast traffic.

OBJECT-TYPE

Configures the multicast storm recovery threshold for this port as a percentage of port speed.

OBJECT-TYPE

The switch config unicast allows you to enable or disable unicast storm recovery mode. When you specify Enable for unicast Storm Recovery and the unknown unicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the unknown unicast traffic.

OBJECT-TYPE

Configures the unicast storm recovery threshold for this port as a percentage of port speed.

OBJECT-IDENTITY

OBJECT-TYPE

Dhcp Filtering mode: enable - enable dhcp filtering mode disable - disable dhcp filtering mode.

OBJECT-TYPE

A table that contains the configuration objects for the with each port.

OBJECT-TYPE

The configuration information for Dhcp Filtering.

OBJECT-TYPE

Port's DHCP mode. It can be either trusted or untrusted default will be untrusted.

OBJECT-IDENTITY

OBJECT-TYPE

The switch's protected port mapping table

OBJECT-TYPE

Protected ports assigned to groups.

OBJECT-TYPE

The group that this port belongs to

OBJECT-TYPE

The name of the group

OBJECT-TYPE

The set of ports that are protected in this group

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP/MLD Snooping Querier Global configuration entries.

OBJECT-TYPE

Represents entry for Snooping Querier Configuration.

OBJECT-TYPE

This enables or disables Snooping Querier on the system.

OBJECT-TYPE

This specifies the multicast protocol versions that are supported by the system.

OBJECT-TYPE

This specifies the default source ip address to be used while generating general queries.

OBJECT-TYPE

This specified the timer interval after which the system generates general queries.

OBJECT-TYPE

This specified the timer interval after which the detected other querier information is no longer valid.

OBJECT-TYPE

A table of the Snooping Querier Vlan configuration entries.

OBJECT-TYPE

Represents entry for a Snooping Querier configurable Vlan.

OBJECT-TYPE

This enables or disables Snooping Querier on a selected Vlan interface.

OBJECT-TYPE

This specifies the current state of the Snooping Querier on a selected vlan interface

OBJECT-TYPE

This enables or disables the Snooping Querier Election Participation mode. When enabled snooping querier switch will participate in querier election up on discovering another querier in the specified vlan. When disabled, up on discovering another querier, snooping querier moves to non-querier state.

OBJECT-TYPE

This specifies the default source ip address to be used while generating general queries on the specified vlan.

OBJECT-TYPE

This specifies the multicast protocol version that is currently being used by the snooping switch for the specified vlan while generating query messages.

OBJECT-TYPE

The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This object is valid only when agentSwitchSnoopingQuerierOperVersion object is valid.

OBJECT-TYPE

This specifies the last querier's ip address for the specified vlan. It represents the detected other multicast querier in the vlan.

OBJECT-TYPE

This specifies the multicast protocol version that is currently being used by the detected other multicast querier for the specified vlan.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port. SFTP and SCP are only allowed if the SSH feature is present.

OBJECT-TYPE

Transfer upload server IP configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP, or SCP. The address is 4 integer bytes ranging from 0 to 255. This object is deprecated in favour of agentTransferUploadServerAddress and agentTransferUploadServerAddressType.

OBJECT-TYPE

Transfer upload path configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.

OBJECT-TYPE

Transfer upload filename configures the file name for the file being uploaded from the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP.

OBJECT-TYPE

Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - Message log - Trap log - Banner File

OBJECT-TYPE

Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.

OBJECT-TYPE

Indicates the current status of an upload transfer.

OBJECT-TYPE

The type of the serverip address, as defined in the InetAddress MIB. The agentTransferUploadServerAddress object is intepreted within the context of agentTransferUploadServerAddressType

OBJECT-TYPE

Transfer upload serverip configures the IP address of the server where the file is to be uploaded to.It is valid only when the Transfer Mode is TFTP, SFTP or SCP. The type of this address is determined by the value of the agentTransferUploadServerAddressType object. The values for agentTransferUploadServerAddressType and agentTransferUploadServerAddress must be consistent.

OBJECT-TYPE

Transfer upload image name. Sets the image to be uploaded as the specified name Note: Imagename, File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP.

OBJECT-TYPE

Username applicable only to secure upload types, i.e., SFTP or SCP.

OBJECT-TYPE

Password applicable only to secure upload types, i.e. SFTP or SCP.

OBJECT-IDENTITY

OBJECT-TYPE

Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port. SFTP and SCP are only allowed if the SSH feature is present.

OBJECT-TYPE

Transfer download serverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP or SCP. The address is 4 integer bytes ranging from 0 to 255. This object is deprecated in favour of agentTransferDownloadServerAddress and agentTransferDownloadServerAddressType.

OBJECT-TYPE

Transfer download path configures the directory path where the file is located. The switch remembers the last file path used.

OBJECT-TYPE

Transfer download filename configures the file name for the file being downloaded to the switch. It can be up to 32 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 33 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\code\ and File Name set to e1r1v1.opr. Note: Imagename, File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP.

OBJECT-TYPE

Transfer download datatype configures the type of file to download to the switch. The types for download are: code - Code File config - Configuration File sshkey-rsa1 - SSH-1 RSA Key File sshkey-rsa2 - SSH-2 RSA Key PEM File sshkey-dsa - SSH-2 DSA Key PEM File sslpem-root - SSL Trusted Root Certificate PEM File sslpem-server - SSL Server Certificate PEM File sslpem-dhweak - SSL DH Weak Encryption Parameter PEM File sslpem-dhstrong - SSL DH Strong Encryption Parameter PEM File cli-banner - CLI Banner File kernel - Kernel File Note: SSH Key files can only be downloaded if SSH Server is administratively disabled, and there are no active SSH sessions. Kernel file can be downloaded only on raptor platform and linux operating system.

OBJECT-TYPE

Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.

OBJECT-TYPE

Indicates the current status of an download transfer.

OBJECT-TYPE

The type of the serverip address, as defined in the InetAddress MIB. The agentTransferDownloadServerAddress object is intepreted within the context of agentTransferDownloadServerAddressType

OBJECT-TYPE

Transfer download serverip configures the IP address of the server where the file is to be downloaded from.It is valid only when the Transfer Mode is TFTP, SFTP, or SCP. The type of this address is determined by the value of the agentTransferDownloadServerAddressType object. The values for agentTransferDownloadServerAddressType and agentTransferDownloadServerAddress must be consistent.

OBJECT-TYPE

Transfer download image name. Sets the downloaded image as the specified name Note: Imagename, File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP.

OBJECT-TYPE

Username applicable only to secure download types, i.e., SFTP or SCP.

OBJECT-TYPE

Password applicable only to secure download types, i.e. SFTP or SCP.

OBJECT-IDENTITY

OBJECT-TYPE

The image1 softwate version .

OBJECT-TYPE

The image2 software version.

OBJECT-TYPE

The active image name. image1 or image2.

OBJECT-TYPE

The next active image name. user assigns either image1 or image2.

OBJECT-IDENTITY

OBJECT-TYPE

IfIndex of the mirrored port

OBJECT-TYPE

IfIndex of the probe port

OBJECT-TYPE

Port mirroring mode: enable - enable mirroring mode disable - disable mirroring mode delete - clear MirroredPort and Probe Port configuration

OBJECT-TYPE

This table includes entries for each Port Mirroring session.

OBJECT-TYPE

Provides configuration of a Port Mirroring session specifying the destination port, and the source Port Mask, providing a many-to-one mapping.

OBJECT-TYPE

The Session number of this mirroring entry. The number of sessions is fixed, and is platform dependant.

OBJECT-TYPE

The port which traffic from the mirrored ports will be sent to.

OBJECT-TYPE

The ports from which traffic will be sent to the destination port. The destination port can not be included in this list of ports.

OBJECT-TYPE

The status of this port mirroring session. enable(1) - This session is active and all traffic from the source ports will be mirrored to the destination port. disable(2) - This session is not active. delete(3) - Remove the configuration for this Session

OBJECT-TYPE

This table includes entries for each source port's direction of port mirroring.

OBJECT-TYPE

Provides configuration of a Port Mirroring direction specifying the session of the port mirroring and source port

OBJECT-TYPE

The port from which traffic will be sent to the destination port. This port should be a source port in the corresponding session

OBJECT-TYPE

The direction of the data to be mirrored on this source port. tx(1) - The data that is transmitted from the source port. rx(2) - The data that is received on the source port. txrx(3) - The data that is transmitted/received from/on the source port

OBJECT-TYPE

This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.

OBJECT-TYPE

Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port.

OBJECT-TYPE

ifIndex of this physical port

OBJECT-TYPE

Enable/disable 802.3ad LACP on this port

OBJECT-TYPE

A table of the switch's physical port config entries

OBJECT-TYPE

Switch's physical port config entry

OBJECT-TYPE

The port number of this port.

OBJECT-TYPE

The switch's Port IfIndex

OBJECT-TYPE

The switch's Port Type

OBJECT-TYPE

The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port This object is only supported when the Dot1d Protocol is enabled.

OBJECT-TYPE

The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled.

OBJECT-TYPE

The switch's Port Admin Mode

OBJECT-TYPE

The switch's Port Speed Mode. This is the configured physical mode. This object is read-only for gigabit ports

OBJECT-TYPE

The switch's Port Physical Speed Status. This is the current actual speed.

OBJECT-TYPE

If enabled, link up and link down traps will be sent for this port.

OBJECT-TYPE

clear stats for this port only

OBJECT-TYPE

This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. The set of possible values for this object is the same as the set defined for the agentPortType object. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType10GBaseSX

OBJECT-TYPE

This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object agentPortDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object agentPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType10GBaseSX

OBJECT-TYPE

This object identifies the administration status of auto negotiation for this port.

OBJECT-TYPE

Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports.

OBJECT-TYPE

This object identifies the largest value that can be configured for agentPortMaxFrameSize

OBJECT-TYPE

This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of agentPortMaxFrameSizeLimit. For Ethernet ports which support 802.1Q vlan tagging, the minimum value that this object can be set to is 1522

OBJECT-TYPE

If enabled, broadcast storm recovery will function on this port. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the broadcast traffic.

OBJECT-TYPE

Configures the broadcast storm recovery threshold for this port as a percentage of port speed.

OBJECT-TYPE

If enabled, multicast storm recovery will function on this port. When you specify Enable for Multicast Storm Recovery and the multicast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the multicast traffic.

OBJECT-TYPE

Configures the multicast storm recovery threshold for this port as a percentage of port speed.

OBJECT-TYPE

If enabled, unicast storm recovery will function on this port. When you specify Enable for Unicast Storm Recovery and the unknown unicast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the unknown unicast traffic.

OBJECT-TYPE

Configures the unicast storm recovery threshold for this port as a percentage of port speed.

OBJECT-IDENTITY

OBJECT-TYPE

The MST configuration digest key.

OBJECT-TYPE

The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard.

OBJECT-TYPE

The MST configuration name of at most 32 characters.

OBJECT-TYPE

The MST configuration revision. The default value is 1.

OBJECT-TYPE

The MST configuration force protocol version. The default version is dot1s.

OBJECT-TYPE

The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational status on the switch. The default status is disabled.

OBJECT-TYPE

The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status is disabled.

OBJECT-TYPE

The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Filter Mode on the switch. The default status is disabled.

OBJECT-TYPE

STP port table.

OBJECT-TYPE

STP port entry.

OBJECT-TYPE

The administrative STP state for the port. enable(1) - enables STP on the port. disable(2) - disables STP on the port. The default port STP state is enabled for the first 4095 ports and disabled for any ports beyond.

OBJECT-TYPE

The MSTP BPDUs received on a specific port.

OBJECT-TYPE

The MSTP BPDUs sent from a specific port.

OBJECT-TYPE

The RSTP BPDUs received on a specific port.

OBJECT-TYPE

The RSTP BPDUs sent from a specific port.

OBJECT-TYPE

The STP BPDUs received on a specific port.

OBJECT-TYPE

The STP BPDUs sent from a specific port.

OBJECT-TYPE

Time since port was reset. It is displayed in days, hours, minutes, and seconds.

OBJECT-TYPE

Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A non-zero value indicates that BPDUs are to be sent on the specified port.

OBJECT-TYPE

Hello time for the STP port. The default value is 2.

OBJECT-IDENTITY

OBJECT-TYPE

The MSTP root port hello time for the CIST.

OBJECT-TYPE

The MSTP root port max age for the CIST.

OBJECT-TYPE

The MSTP regional root identifier for the CIST.

OBJECT-TYPE

The MSTP regional root path cost for the CIST.

OBJECT-TYPE

The MSTP root port forward delay for the CIST.

OBJECT-TYPE

The MSTP bridge forward delay for the CIST. The default value is 15.

OBJECT-TYPE

The MSTP bridge hello time for the CIST. The default value is 2. According to IEEE 802.1Q-REV 2005 updating hello time is disallowed

OBJECT-TYPE

The MSTP bridge hold time for the CIST.

OBJECT-TYPE

The MSTP bridge max age for the CIST. The default value is 20.

OBJECT-TYPE

The MSTP bridge max hops for the CIST. The default value is 20.

OBJECT-TYPE

The MSTP bridge priority for the CIST. The default value is 32768.

OBJECT-TYPE

The MSTP bridge hold count for the CIST. This command sets the value of maximum bpdus that a bridge is allowed to send within a hello time window. The default value is 6.

OBJECT-TYPE

The MSTP time since the last topology change for the CIST.

OBJECT-TYPE

The MSTP count of topology changes for the CIST.

OBJECT-TYPE

CIST port table.

OBJECT-TYPE

CIST port entry.

OBJECT-TYPE

The MSTP operational status of a specific port for the CIST.

OBJECT-TYPE

The MSTP operational point to point mac of a specific port for the CIST.

OBJECT-TYPE

The MSTP topology change acknowledge for a specific port in the CIST.

OBJECT-TYPE

The administrative state of a specific port in CIST. enable(1) - enables the port. disable(2) - disables the port. The default port state is disabled.

OBJECT-TYPE

The MSTP forwarding state of a specific port in CIST.

OBJECT-TYPE

The MSTP port identifier of a specific port in CIST.

OBJECT-TYPE

The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.

OBJECT-TYPE

The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128.

OBJECT-TYPE

The MSTP designated bridge ID of a specific port in CIST.

OBJECT-TYPE

The MSTP designated cost of a specific port in CIST.

OBJECT-TYPE

The MSTP designated port ID of a specific port in CIST.

OBJECT-TYPE

The MSTP external port path cost in CIST. The default value varies depending upon the link speed.

OBJECT-TYPE

BPDU Guard Mode effect on the port. enable(1) - BPDU Guard Mode is enabled on the port. disable(2) - BPDU Guard Mode is disabled on the port.

OBJECT-TYPE

This command sets BPDU Filter mode on the port. enable(1) - BPDU Filter Mode is enabled on the port. disable(2) - BPDU Filter Mode is disabled on the port.

OBJECT-TYPE

This command sets BPDU Flood mode on the port. enable(1) - BPDU Flood Mode is enabled on the port. disable(2) - BPDU Flood Mode is disabled on the port.

OBJECT-TYPE

This command sets the auto-edge mode of the port which enables it to become an edge port if it does not see BPDUs for some duration. enable(1) - enables the auto-edge mode for the port. disable(2) - disables the auto-edge mode for the port. The default auto-edge mode is disabled.

OBJECT-TYPE

This command sets a port to discard any superior information received by the port and thus protect against root of the device from changing.The port gets put into discarding state and does not forward any packets. enable(1) - enables the root-guard mode for the port. disable(2) - disables the root-guard mode for the port. The default root-guard mode is disabled.

OBJECT-TYPE

This command restricts the port from propagating any topology change information received through that port. enable(1) - enables the tcn-guard mode for the port. disable(2) - disables the tcn-guard mode for the port. The default tcn-guard mode is disabled.

OBJECT-TYPE

MST table.

OBJECT-TYPE

MST entry.

OBJECT-TYPE

The MSTP instance ID.

OBJECT-TYPE

The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768.

OBJECT-TYPE

The MSTP bridge identifier in a specific instance.

OBJECT-TYPE

The MSTP designated root bridge identifier in a specific instance.

OBJECT-TYPE

The MSTP root path cost in a specific instance.

OBJECT-TYPE

The MSTP root port ID in a specific instance.

OBJECT-TYPE

The MSTP time since the last topology change in a specific instance.

OBJECT-TYPE

The MSTP count of topology changes in a specific instance.

OBJECT-TYPE

The MSTP topology change parameter in a specific instance.

OBJECT-TYPE

The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance.

OBJECT-TYPE

MST port table.

OBJECT-TYPE

MST port entry.

OBJECT-TYPE

The MSTP forwarding state of a specific port in a specific instance.

OBJECT-TYPE

The MSTP port identifier of a specific port in a specific instance.

OBJECT-TYPE

The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.

OBJECT-TYPE

The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128.

OBJECT-TYPE

The MSTP designated bridge ID of a specific port in a specific instance.

OBJECT-TYPE

The MSTP designated cost of a specific port in a specific instance.

OBJECT-TYPE

The MSTP designated port ID of a specific port in a specific instance.

OBJECT-TYPE

MST VLAN table.

OBJECT-TYPE

MST VLAN entry.

OBJECT-TYPE

The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN.

OBJECT-IDENTITY

OBJECT-TYPE

Authentication List Create If set to a non empty string, creates a new Authentication List for configuration.

OBJECT-TYPE

MST VLAN table.

OBJECT-TYPE

MST VLAN entry.

OBJECT-TYPE

Authenticaiton List Index Unique number used for indexing into this table.

OBJECT-TYPE

Authenticaiton List Name Unique name used to identify the Authentication List from other tables.

OBJECT-TYPE

Authenticion List Method 1 Configures the first authentication method to use when this list is specified.

OBJECT-TYPE

Authenticion List Method 2 Configures the second authentication method to use when this list is specified.

OBJECT-TYPE

Authenticion List Method 3 Configures the third authentication method to use when this list is specified.

OBJECT-TYPE

The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List destroy(6) - removes the Authentication List.

OBJECT-TYPE

Authenticion List Method 4 Configures the fourth authentication method to use when this list is specified.

OBJECT-TYPE

Default Authentication List This object configures which authentication list to use for users which do not have an Authentication List configured. The list must be configured before setting.

OBJECT-TYPE

User Authentication Config Table

OBJECT-TYPE

User Authentication Config Entry

OBJECT-TYPE

User Authentication List This object configures which authentication list to use for this user. The list must be configured before setting.

OBJECT-TYPE

User Port Config Table

OBJECT-TYPE

User Port Config Entry

OBJECT-TYPE

User Port Port Security This object configures which ports the user has access to. Ports are indexed based on dot1dBasePort entries in dot1dBasePortTable.

OBJECT-IDENTITY

OBJECT-TYPE

A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port.

OBJECT-TYPE

A 802.1p priority mapped to a traffic class priority queue.

OBJECT-TYPE

The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port.

OBJECT-TYPE

Traffic class priority queue the received frame is mapped to.

OBJECT-IDENTITY

OBJECT-TYPE

Configures the HTTP server admin mode

OBJECT-TYPE

Configures the use of the Java interface through Web connections.

OBJECT-TYPE

Configures the maximum number of allowable HTTP sessions. The default value is 16.

OBJECT-TYPE

Configures the hard timeout for HTTP sessions in hours. The default value is 24 hours. A value of 0 gives an infinite timeout.

OBJECT-TYPE

Configures the soft (activity) timeout for HTTP sessions in minutes. The default value is 5 minutes. A value of 0 gives an infinite timeout.

OBJECT-IDENTITY

OBJECT-TYPE

enable(1) will initiate an configuration save to nvram. Status is returned by the object agentSaveConfigStatus.

OBJECT-TYPE

clear config to factory defaults

OBJECT-TYPE

clear lag configuration

OBJECT-TYPE

close all telnet sessions

OBJECT-TYPE

reset passwords

OBJECT-TYPE

clear all port statistics

OBJECT-TYPE

clear all switch statistics

OBJECT-TYPE

clear trap log

OBJECT-TYPE

clear vlan entries

OBJECT-TYPE

Resets the switch. This object is not valid for stacking platforms.

OBJECT-TYPE

Indicates the current status of an save configuration request.

OBJECT-IDENTITY

OBJECT-TYPE

Status of the Virtual Cable Tester active(1) - cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set.

OBJECT-TYPE

Determines on which port to perform the cable test. Limited to copper based ports.

OBJECT-TYPE

Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress.

OBJECT-TYPE

The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.

OBJECT-TYPE

The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.

OBJECT-TYPE

The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if agentCableTesterStatus is not success(2).