MIBs Depot

Modem-MIB

Registered at
1.3.6.1.2.1.38
Last updated
1994-06-12 00:00
Organization
IETF Modem Management Working Group
Namespace
standard
Source file
Modem-MIB
Digest
sha256:f973a14cccd938bbb8944d4ff2610ebab85df760699f03be240ffe9a2e3095d1

Description

The MIB module for management of dial-up modems.

Contact

Steven Waldbusser Postal: Carnegie Mellon University 5000 Forbes Ave Pittsburgh, PA, 15213 US Tel: +1 412 268 6628 Fax: +1 412 268 4987 E-mail: waldbusser@cmu.edu

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso, mib-2
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

Modem-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
mdmMib
OBJECT-IDENTITY
1.3.6.1.2.1.38
mdmMIBObjects
OBJECT-IDENTITY
1.3.6.1.2.1.38.1.1
mdmNumber
OBJECT-TYPE
The number of modem rows in the modem table. This value defines the maximum value of the mdmIndex object.
1.3.6.1.2.1.38.1.1.1Integer32read-onlycurrent
mdmIDTable
OBJECT-TYPE
The base table for the modems managed by this MIB. The mdmLineTable, mdmDTEInterfaceTable, mdmCallControlTable, and mdmStatsTable all augment the rows defined in this table.
1.3.6.1.2.1.38.1.1.2not-accessiblecurrent
mdmIDEntry
OBJECT-TYPE
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
1.3.6.1.2.1.38.1.1.2.1not-accessiblecurrent
mdmIndex
OBJECT-TYPE
A unique number for each modem that ranges from 1 to mdmNumber. The value must remain constant at least from one re-initialization of the network management agent to the next.
1.3.6.1.2.1.38.1.1.2.1.1Integer32 (1..65535)not-accessiblecurrent
mdmIDManufacturerOID
OBJECT-TYPE
This value is intended to identify the manufacturer, model, and version of this modem. This may be used to identify the existance of enterprise-specific functions and behaviours.
1.3.6.1.2.1.38.1.1.2.1.2OBJECT IDENTIFIERread-onlycurrent
mdmIDProductDetails
OBJECT-TYPE
A textual description of this device, including the manufacturer's name, modem model name, hardware revision, firmware revision, and optionally, its serial number. The exact format of this description is defined by the vendor. This description may only contain characters from the NVT ASCII character set.
1.3.6.1.2.1.38.1.1.2.1.3DisplayString (SIZE(0..79))read-onlycurrent
mdmLineTable
OBJECT-TYPE
The modem Line Table augments the modem ID table.
1.3.6.1.2.1.38.1.1.3not-accessiblecurrent
mdmLineEntry
OBJECT-TYPE
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
1.3.6.1.2.1.38.1.1.3.1not-accessiblecurrent
mdmLineCarrierLossTime
OBJECT-TYPE
Duration in 10ths of a second the modem waits after loss of carrier before hanging up. If this value is set to `255', the modem will not hang up upon loss of carrier. This allows the modem to distinguish between a momentary lapse in line quality and a true disconnect and can be useful to tune the tolerance of the modem to lines of poor quality.
1.3.6.1.2.1.38.1.1.3.1.1Integer32 (1..255)read-writecurrent
mdmLineState
OBJECT-TYPE
Allows the inspection and alteration of the state of the modem. Management commands may change the state to `on- hook', `busied-out', or `reset' from any state. No other alterations are permitted from the management protocol. When this object is set to reset, the modem shall be reset and the value will change to the modem's new, implementation dependent state.
1.3.6.1.2.1.38.1.1.3.1.2INTEGER {unknown(1), onHook(2), offHook(3), connected(4), busiedOut(5), reset(6)}read-writecurrent
mdmLineCapabilitiesTable
OBJECT-TYPE
A list of protocol capabilities for this modem.
1.3.6.1.2.1.38.1.1.4not-accessiblecurrent
mdmLineCapabilitiesEntry
OBJECT-TYPE
A listing of the protocol(s) that this modem is capable of. Entries in this table are created only by the agent. One entry exists for each protocol that the modem is capable of, regardless of whether that protocol is enabled or not. This table is useful for providing an inventory of the capabilities on a modem, and allowing the manager to enable or disable capabilities from the menu of available possibilities. Row creation is not required to enable or disable capabilities.
1.3.6.1.2.1.38.1.1.4.1not-accessiblecurrent
mdmLineCapabilitiesIndex
OBJECT-TYPE
A unique index for this capabilities entry.
1.3.6.1.2.1.38.1.1.4.1.1Integer32not-accessiblecurrent
mdmLineCapabilitiesID
OBJECT-TYPE
An identifier for this capability. Standard protocol capabilities will have identifiers registered in this document or other companion standards documents. Proprietary protocol capabilities will be registered by their respective organization. All capabilities, standard or vendor-specific, shall be registered in this table.
1.3.6.1.2.1.38.1.1.4.1.2OBJECT IDENTIFIERread-onlycurrent
mdmLineCapabilitiesEnableRequested
OBJECT-TYPE
The requested configuration of this capability. If this value is 'disabled(1)', this is a request to disable this protocol. If this value is 'preferred(3)', this is a request to enable this protocol, and to prefer it in any negotiation over other appropriate protocols that have a value of 'optional(2)'.
1.3.6.1.2.1.38.1.1.4.1.3INTEGER {disabled(1), optional(2), preferred(3)}read-writecurrent
mdmLineCapabilitiesEnableGranted
OBJECT-TYPE
The actual configuration of this capability. The agent shall attempt to set this as close as possible to the associated mdmLineCapabilitiesEnableRequested value. The agent shall make this determination in an implementation- specific manner that may take into account the configuration of other capabilities or other considerations. The modem will choose in an implementation-specific manner between multiple mutually-exclusive capabilities that each have the same (non-disabled) value. However, the modem must prefer all capabilities with a value of 'preferred(3)' over all capabilities with a value of 'optional(2)'. In other words, if there are one or more mutually-exclusive capabilities (e.g. V.32 and V.32bis) that are set to `preferred', the agent must choose one in an implementation-specific manner. Otherwise, if there are one or more mutually-exclusive capabilities that are set to `optional', the agent must choose one in an implementation- specific manner.
1.3.6.1.2.1.38.1.1.4.1.4INTEGER {disabled(1), optional(2), preferred(3)}read-onlycurrent
mdmLineCapabilities
OBJECT-IDENTITY
1.3.6.1.2.1.38.1.1.5
mdmLineCapabilitiesV21
OBJECT-IDENTITY
ITU V.21
1.3.6.1.2.1.38.1.1.5.1current
mdmLineCapabilitiesV22
OBJECT-IDENTITY
ITU V.22
1.3.6.1.2.1.38.1.1.5.2current
mdmLineCapabilitiesV22bis
OBJECT-IDENTITY
ITU V.22bis
1.3.6.1.2.1.38.1.1.5.3current
mdmLineCapabilitiesV23CC
OBJECT-IDENTITY
ITU V.23CC
1.3.6.1.2.1.38.1.1.5.4current
mdmLineCapabilitiesV23SC
OBJECT-IDENTITY
ITU V.23SC
1.3.6.1.2.1.38.1.1.5.5current
mdmLineCapabilitiesV25bis
OBJECT-IDENTITY
ITU V.25bis
1.3.6.1.2.1.38.1.1.5.6current
mdmLineCapabilitiesV26bis
OBJECT-IDENTITY
ITU V.26bis
1.3.6.1.2.1.38.1.1.5.7current
mdmLineCapabilitiesV26ter
OBJECT-IDENTITY
ITU V.26ter
1.3.6.1.2.1.38.1.1.5.8current
mdmLineCapabilitiesV27ter
OBJECT-IDENTITY
ITU V.27ter
1.3.6.1.2.1.38.1.1.5.9current
mdmLineCapabilitiesV32
OBJECT-IDENTITY
ITU V.32
1.3.6.1.2.1.38.1.1.5.10current
mdmLineCapabilitiesV32bis
OBJECT-IDENTITY
ITU V.32bis
1.3.6.1.2.1.38.1.1.5.11current
mdmLineCapabilitiesV32terbo
OBJECT-IDENTITY
ITU V.32terbo
1.3.6.1.2.1.38.1.1.5.12current
mdmLineCapabilitiesVFC
OBJECT-IDENTITY
ITU V.FC
1.3.6.1.2.1.38.1.1.5.13current
mdmLineCapabilitiesV34
OBJECT-IDENTITY
ITU V.34
1.3.6.1.2.1.38.1.1.5.14current
mdmLineCapabilitiesV42
OBJECT-IDENTITY
ITU V.42
1.3.6.1.2.1.38.1.1.5.15current
mdmLineCapabilitiesV42bis
OBJECT-IDENTITY
ITU V.42bis
1.3.6.1.2.1.38.1.1.5.16current
mdmLineCapabilitiesMNP1
OBJECT-IDENTITY
MNP1
1.3.6.1.2.1.38.1.1.5.17current
mdmLineCapabilitiesMNP2
OBJECT-IDENTITY
MNP2
1.3.6.1.2.1.38.1.1.5.18current
mdmLineCapabilitiesMNP3
OBJECT-IDENTITY
MNP3
1.3.6.1.2.1.38.1.1.5.19current
mdmLineCapabilitiesMNP4
OBJECT-IDENTITY
MNP4
1.3.6.1.2.1.38.1.1.5.20current
mdmLineCapabilitiesMNP5
OBJECT-IDENTITY
MNP5
1.3.6.1.2.1.38.1.1.5.21current
mdmLineCapabilitiesMNP6
OBJECT-IDENTITY
MNP6
1.3.6.1.2.1.38.1.1.5.22current
mdmLineCapabilitiesMNP7
OBJECT-IDENTITY
MNP7
1.3.6.1.2.1.38.1.1.5.23current
mdmLineCapabilitiesMNP8
OBJECT-IDENTITY
MNP8
1.3.6.1.2.1.38.1.1.5.24current
mdmLineCapabilitiesMNP9
OBJECT-IDENTITY
MNP9
1.3.6.1.2.1.38.1.1.5.25current
mdmLineCapabilitiesMNP10
OBJECT-IDENTITY
MNP10
1.3.6.1.2.1.38.1.1.5.26current
mdmLineCapabilitiesV29
OBJECT-IDENTITY
ITU V.29
1.3.6.1.2.1.38.1.1.5.27current
mdmLineCapabilitiesV33
OBJECT-IDENTITY
ITU V.33
1.3.6.1.2.1.38.1.1.5.28current
mdmLineCapabilitiesBell208
OBJECT-IDENTITY
Bell 208
1.3.6.1.2.1.38.1.1.5.29current
mdmDTEInterfaceTable
OBJECT-TYPE
The modem DTE Interface Table augments the modem ID table.
1.3.6.1.2.1.38.1.1.6not-accessiblecurrent
mdmDTEInterfaceEntry
OBJECT-TYPE
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
1.3.6.1.2.1.38.1.1.6.1not-accessiblecurrent
mdmDTEActionDTROnToOff
OBJECT-TYPE
Defines the action the modem will take when DTR drops. If the value is set to ignore(1), the modem takes no action when DTR drops. Typically, mdmDTEActionDTROffToOn would also be set to ignore(1) if this object is set to ignore(1). If the value is escapeToCommandMode(2), the modem remains connected and enters command mode. If the value is disconnectCall(3), the current call (if any) is terminated and the modem will not auto-answer while DTR is off. If the value is resetModem(4), the current call (if any) is terminated and the modem is reset.
1.3.6.1.2.1.38.1.1.6.1.1INTEGER {ignore(1), escapeToCommandMode(2), disconnectCall(3), resetModem(4)}read-writecurrent
mdmDTEActionDTROffToOn
OBJECT-TYPE
Defines the action the modem will take when DTR is raised. If the value is set to ignore(1), the modem takes no action when DTR is raised. Typically, mdmDTEActionDTROnToOff would also be set to ignore(1) if this object is set to ignore(1). If the value is set to enableDial(2), the modem prepares to dial an outgoing call. If the value is set to autoAnswerEnable(3), the modem will be configured to answer any incoming call. If the value is set to establishConnection(4), the modem dials an implementation specific number. Immediately after any reset or power-on of the modem, if the DTR is high, the action specified here will be executed.
1.3.6.1.2.1.38.1.1.6.1.2INTEGER {ignore(1), enableDial(2), autoAnswerEnable(3), establishConnection(4)}read-writecurrent
mdmDTESyncTimingSource
OBJECT-TYPE
The clock source for synchronous transmissions. If set to internal(1), the modem is the clock source and sends the clock signals to the DTE. If set to external(2), the transmit clock signals are provided by the DTE. If loopback(3), the modem receiver clock is used for the transmit clock. If network(4), the clock signals are supplied by the DCE interface. If the modem is not in synchronous mode, setting this object will have no effect on the current operations of the modem.
1.3.6.1.2.1.38.1.1.6.1.3INTEGER {internal(1), external(2), loopback(3), network(4)}read-writecurrent
mdmDTESyncAsyncMode
OBJECT-TYPE
The operational mode of the modem. If the value is syncAfterDial(3), the modem will accept commands in asynchronous mode and change to synchronous mode to pass data after a dial sequence has been executed.
1.3.6.1.2.1.38.1.1.6.1.4INTEGER {async(1), sync(2), syncAfterDial(3)}read-writecurrent
mdmDTEInactivityTimeout
OBJECT-TYPE
The amount of idle time in minutes that the modem will wait before disconnecting a connection. When a call is connected and no data is transferred (continuous marking condition) on both circuits 103 and 104 for the specified time, the DCE disconnects the call. If the value is 0, no idle disconnect will occur. This function applies to asynchronous dial operations only and is intended for administrative control over idle connections.
1.3.6.1.2.1.38.1.1.6.1.5Integer32 (0..65535)read-writecurrent
mdmCallControlTable
OBJECT-TYPE
The modem Call Control Table augments the modem ID table.
1.3.6.1.2.1.38.1.1.7not-accessiblecurrent
mdmCallControlEntry
OBJECT-TYPE
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
1.3.6.1.2.1.38.1.1.7.1not-accessiblecurrent
mdmCCRingsBeforeAnswer
OBJECT-TYPE
Determines which ring the modem will wait to answer the phone on. If this value is `0', the modem will not go offhook and answer a call when a ring signal is detected.
1.3.6.1.2.1.38.1.1.7.1.1Integer32read-writecurrent
mdmCCCallSetUpFailTimer
OBJECT-TYPE
This parameter specifies the amount of time, in seconds, that the modem shall allow between either answering a call (automatically or manually) or completion of dialing, and establishment of a connection with the remote modem. If no connection is established during this time, the modem disconnects from the line and returns a result code indicating the cause of the disconnection. In TIA-602, this is controlled by the value in the S7 register.
1.3.6.1.2.1.38.1.1.7.1.2Integer32 (0..255)read-writecurrent
mdmCCResultCodeEnable
OBJECT-TYPE
When disabled, the DCE shall issue no 'result codes' of any kind to the DTE either in response to unsolicited events (eg. ring signal), or commands. In TIA-602, this is controlled by the ATQ command. When numericEnabled, the DCE shall issue result codes in numeric form. When verboseEnabled, the DCE shall issue result codes in a verbose, textual form.
1.3.6.1.2.1.38.1.1.7.1.3INTEGER {disabled(1), numericEnabled(2), verboseEnabled(3)}read-writecurrent
mdmCCEscapeAction
OBJECT-TYPE
The modem's action upon successfully recognizing the 'escape to command mode' character sequence.
1.3.6.1.2.1.38.1.1.7.1.4INTEGER {ignoreEscape(1), hangUp(2), enterCommandMode(3)}read-writecurrent
mdmCCCallDuration
OBJECT-TYPE
Present or last completed connection time in seconds. If there have been no previous connections, this value should be -1.
1.3.6.1.2.1.38.1.1.7.1.5Integer32read-onlycurrent
mdmCCConnectionFailReason
OBJECT-TYPE
Indicates the reason that the last connection or attempt failed. The meaning of each reason code is explained below. unknown: This code means the failure reason is unknown or there has been no previous call. other: This code used when no other code is applicable. Additional vendor information may be available elsewhere. managementCommand: A management command terminated the call. These commands include escaping to command mode, initiating dialing, restoring lines, and disconnecting. inactivityTimeout: The call was terminated because it was inactive for at the minimum duration specified. mnpIncompatibility: The modems are unable to resolve MNP protocol differences. protocolError: An error occured in one of protocol in use. Further information is required to determine in which protocol the error occurred, and the exact nature of the error. powerLoss: The modem lost power and disconnected the call. equipmentFailure: The modem equipment failed. dtrDrop: DTR has been turned off while the modem is to disconnect on DTR drop. (Ref: V.58 cct108TurnedOff) noDialTone: If the modem is to monitor for call progress tones, but the modem has failed to detect dial tone while attempting to dial a number. lineBusy: Busy signal is detected while busy signal detection is enabled, or while the 'W' or '@' dial modifier is used. (Ref: V.58 engagedTone) noAnswer: The call was not answered. voiceDetected: A voice was detected on the call. carrierLost: Indicates that the modem has disconnected due to detection of loss of carrier. In TIA-602, the S10 register determines the time that loss of carrier must be detected before the modem disconnects. trainingFailed: Indicates that the modems did not successfully train and reach data mode on the previous connection. faxDetected: A fax was detected on the call.
1.3.6.1.2.1.38.1.1.7.1.6INTEGER {unknown(1), other(2), managementCommand(3), inactivityTimeout(4), mnpIncompatibility(5), protocolError(6), powerLoss(10), equipmentFailure(11), dtrDrop(20), noDialTone(30), lineBusy(31), noAnswer(32), voiceDetected(33), carrierLost(40), trainingFailed(41), faxDetected(42)}read-onlycurrent
mdmCCStoredDialStringTable
OBJECT-TYPE
The table of stored dial strings.
1.3.6.1.2.1.38.1.1.8not-accessiblecurrent
mdmCCStoredDialStringEntry
OBJECT-TYPE
A stored dial string.
1.3.6.1.2.1.38.1.1.8.1not-accessiblecurrent
mdmCCStoredDialStringIndex
OBJECT-TYPE
The unique index of a particular dial string.
1.3.6.1.2.1.38.1.1.8.1.1Integer32 (0..65535)not-accessiblecurrent
mdmCCStoredDialString
OBJECT-TYPE
A dial string stored in the modem.
1.3.6.1.2.1.38.1.1.8.1.2DisplayString (SIZE(0..64))read-writecurrent
mdmECTable
OBJECT-TYPE
The modem error correcting table augments the modem ID table.
1.3.6.1.2.1.38.1.1.9not-accessiblecurrent
mdmECEntry
OBJECT-TYPE
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
1.3.6.1.2.1.38.1.1.9.1not-accessiblecurrent
mdmECErrorControlUsed
OBJECT-TYPE
Indicates the error control method used during the current or previous call. This shall be one of the values for error control protocols registered in the capabilities table for this modem. If no error control protocol is in use, this object shall have the value '{0 0}'.
1.3.6.1.2.1.38.1.1.9.1.1OBJECT IDENTIFIERread-onlycurrent
mdmDCTable
OBJECT-TYPE
The modem data compression table augments the modem ID table.
1.3.6.1.2.1.38.1.1.10not-accessiblecurrent
mdmDCEntry
OBJECT-TYPE
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
1.3.6.1.2.1.38.1.1.10.1not-accessiblecurrent
mdmDCCompressionTypeUsed
OBJECT-TYPE
Indicates the data compression method used during the current or previous call. This shall be one of the values for compression protocols registered in the capabilities table for this modem. If no compression protocol is in use, this object shall have the value '{0 0}'.
1.3.6.1.2.1.38.1.1.10.1.1OBJECT IDENTIFIERread-onlycurrent
mdmSCTable
OBJECT-TYPE
The modem signal convertor table augments the modem ID table.
1.3.6.1.2.1.38.1.1.11not-accessiblecurrent
mdmSCEntry
OBJECT-TYPE
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
1.3.6.1.2.1.38.1.1.11.1not-accessiblecurrent
mdmSCCurrentLineTransmitRate
OBJECT-TYPE
The current link transmit rate of a connection, or the last link transmit rate of the last connection in bits per second.
1.3.6.1.2.1.38.1.1.11.1.1Integer32read-onlycurrent
mdmSCCurrentLineReceiveRate
OBJECT-TYPE
The current link receive rate of a connection, or the last link receive rate of the last connection in bits per second.
1.3.6.1.2.1.38.1.1.11.1.2Integer32read-onlycurrent
mdmSCInitialLineTransmitRate
OBJECT-TYPE
The initial link transmit rate of the current connection, or the initial link transmit rate of the last connection in bits per second.
1.3.6.1.2.1.38.1.1.11.1.3Integer32read-onlycurrent
mdmSCInitialLineReceiveRate
OBJECT-TYPE
The initial link receive rate of the current connection, or the initial link receive rate of the last connection in bits per second.
1.3.6.1.2.1.38.1.1.11.1.4Integer32read-onlycurrent
mdmSCModulationSchemeUsed
OBJECT-TYPE
The modulation scheme of the current or previous call. This shall be one of the values for modulation protocols registered in the capabilities table for this modem.
1.3.6.1.2.1.38.1.1.11.1.5OBJECT IDENTIFIERread-onlycurrent
mdmStatsTable
OBJECT-TYPE
The modem statistics Table augments the modem ID table.
1.3.6.1.2.1.38.1.1.12not-accessiblecurrent
mdmStatsEntry
OBJECT-TYPE
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
1.3.6.1.2.1.38.1.1.12.1not-accessiblecurrent
mdmStatsRingNoAnswers
OBJECT-TYPE
The number of events in which ringing was detected but the call was not answered.
1.3.6.1.2.1.38.1.1.12.1.1Counter32read-onlycurrent
mdmStatsIncomingConnectionFailures
OBJECT-TYPE
The number of incoming connection requests that this modem answered in which it could not train with the other DCE.
1.3.6.1.2.1.38.1.1.12.1.2Counter32read-onlycurrent
mdmStatsIncomingConnectionCompletions
OBJECT-TYPE
The number of incoming connection requests that this modem answered and successfully trained with the other DCE.
1.3.6.1.2.1.38.1.1.12.1.3Counter32read-onlycurrent
mdmStatsFailedDialAttempts
OBJECT-TYPE
The number of call attempts that failed because the modem didn't go off hook, or there was no dialtone.
1.3.6.1.2.1.38.1.1.12.1.4Counter32read-onlycurrent
mdmStatsOutgoingConnectionFailures
OBJECT-TYPE
The number of outgoing calls from this modem which sucessfully went off hook and dialed, in which it could not train with the other DCE.
1.3.6.1.2.1.38.1.1.12.1.5Counter32read-onlycurrent
mdmStatsOutgoingConnectionCompletions
OBJECT-TYPE
The number of outgoing calls from this modem which resulted in successfully training with the other DCE.
1.3.6.1.2.1.38.1.1.12.1.6Counter32read-onlycurrent
mdmStatsRetrains
OBJECT-TYPE
The number of retrains experienced on connections on this line.
1.3.6.1.2.1.38.1.1.12.1.7Counter32read-onlycurrent
mdmStats2400OrLessConnections
OBJECT-TYPE
The number of connections initially established at a modulation speed of 2400 bits per second or less.
1.3.6.1.2.1.38.1.1.12.1.8Counter32read-onlycurrent
mdmStats2400To14400Connections
OBJECT-TYPE
The number of connections initially established at a modulation speed of greater than 2400 bits per second and less than 14400 bits per second.
1.3.6.1.2.1.38.1.1.12.1.9Counter32read-onlycurrent
mdmStatsGreaterThan14400Connections
OBJECT-TYPE
The number of connections initially established at a modulation speed of greater than 14400 bits per second.
1.3.6.1.2.1.38.1.1.12.1.10Counter32read-onlycurrent
mdmStatsErrorControlledConnections
OBJECT-TYPE
The number of established connections using an error control protocol.
1.3.6.1.2.1.38.1.1.12.1.11Counter32read-onlycurrent
mdmStatsCompressedConnections
OBJECT-TYPE
The number of established connections using a compression protocol.
1.3.6.1.2.1.38.1.1.12.1.12Counter32read-onlycurrent
mdmStatsCompressionEfficiency
OBJECT-TYPE
The number of bytes transferred into the compression encoder divided by the number of bytes transferred out of the encoder, multiplied by 100 for either the current or last call. If a data compression protocol is not in use, this value shall be `100'.
1.3.6.1.2.1.38.1.1.12.1.13Integer32 (0..65535)read-onlycurrent
mdmStatsSentOctets
OBJECT-TYPE
The number of octets presented to the modem by the DTE.
1.3.6.1.2.1.38.1.1.12.1.14Counter32read-onlycurrent
mdmStatsReceivedOctets
OBJECT-TYPE
The number of octets presented to the DTE by the modem.
1.3.6.1.2.1.38.1.1.12.1.15Counter32read-onlycurrent
mdmStatsSentDataFrames
OBJECT-TYPE
The number of data frames sent on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment.
1.3.6.1.2.1.38.1.1.12.1.16Counter32read-onlycurrent
mdmStatsReceivedDataFrames
OBJECT-TYPE
The number of data frames received on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment.
1.3.6.1.2.1.38.1.1.12.1.17Counter32read-onlycurrent
mdmStatsResentFrames
OBJECT-TYPE
The number of times this modem retransmits frames on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment.
1.3.6.1.2.1.38.1.1.12.1.18Counter32read-onlycurrent
mdmStatsErrorFrames
OBJECT-TYPE
The number of block errors received on the link. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment.
1.3.6.1.2.1.38.1.1.12.1.19Counter32read-onlycurrent
mdmConformance
OBJECT-IDENTITY
1.3.6.1.2.1.38.1.2
mdmCompliances
OBJECT-IDENTITY
1.3.6.1.2.1.38.1.2.1
mdmGroups
OBJECT-IDENTITY
1.3.6.1.2.1.38.1.2.2

Conformance

NameOIDStatus
mdmCompliance
MODULE-COMPLIANCE
The compliance statement for SNMPv2 entities which implement the modem MIB.
1.3.6.1.2.1.38.1.2.1.1current
mdmIDGroup
OBJECT-GROUP
A collection of objects that identify the manufacturer and model information for a modem.
1.3.6.1.2.1.38.1.2.2.1current
mdmLineInterfaceGroup
OBJECT-GROUP
A collection of objects that describe the configuration and state of the modem's line interface.
1.3.6.1.2.1.38.1.2.2.2current
mdmDTEInterfaceGroup
OBJECT-GROUP
A collection of objects that describe the configuration and state of the modem's DTE interface.
1.3.6.1.2.1.38.1.2.2.3current
mdmCallControlGroup
OBJECT-GROUP
A collection of objects that describe the configuration of call control capabilities on the modem and the status of calls placed with this modem.
1.3.6.1.2.1.38.1.2.2.4current
mdmErrorControlGroup
OBJECT-GROUP
A collection of objects that describe the configuration and state of error control on a modem.
1.3.6.1.2.1.38.1.2.2.5current
mdmDataCompressionGroup
OBJECT-GROUP
A collection of objects that describe the configuration and state of data compression on a modem.
1.3.6.1.2.1.38.1.2.2.6current
mdmSignalConvertorGroup
OBJECT-GROUP
A collection of objects that describe the configuration and state of error control on a modem.
1.3.6.1.2.1.38.1.2.2.7current
mdmStatisticsGroup
OBJECT-GROUP
A collection of objects that describe the state of calls on this modem.
1.3.6.1.2.1.38.1.2.2.8current