MIBs Depot

MOXA-NP6000-MIB

Registered at
1.3.6.1.4.1.8691.2
Last updated
2006-07-12 00:00
Organization
Moxa Technologies Co.
Namespace
moxa
Source file
MOXA-NP6000-MIB
Digest
sha256:52dab56ec8aba387bd8f4fac81ab7b39bfeacfaff8a841d56926ad4f84952e83

Description

The MIB module for Moxa NPort 6000 series specific information.

Contact

Email: support@moxa.com.tw Tel : +886 2 89191230 ext.300

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIIpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

MOXA-NP6000-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
PortList
TEXTUAL-CONVENTION
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
current

Objects

NameOIDSyntaxAccessStatus
moxa
OBJECT-IDENTITY
1.3.6.1.4.1.8691
nport
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2
swMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1
overview
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.1
modelName
OBJECT-TYPE
The model name of the NPort. The possible values of this parameter are: 'NP6150' for NPort 6150, 'NP6250' for NPort 6250, 'NP6250-S-SC' for NPort 6250-S-SC, 'NP6250-M-SC' for NPort NPort 6250-M-SC, 'NP6450' for NPort 6450, 'NP6650-8' for NPort 6650-8, and 'NP6650-16' for NPort 6650-16.
1.3.6.1.4.1.8691.2.8.1.1.1DisplayStringread-onlycurrent
serialNumber
OBJECT-TYPE
The serial number of the NPort. Every NPort 6000 series device server is assigned a unique serial number before it is shipped.
1.3.6.1.4.1.8691.2.8.1.1.2INTEGERread-onlycurrent
firmwareVersion
OBJECT-TYPE
The version of the firmware currently running on the NPort.
1.3.6.1.4.1.8691.2.8.1.1.3DisplayStringread-onlycurrent
macAddress
OBJECT-TYPE
The MAC address of the NPort's Ethernet interface.
1.3.6.1.4.1.8691.2.8.1.1.4MacAddressread-onlycurrent
viewLanSpeed
OBJECT-TYPE
The current speed and link status of the NPort's built-in LAN port. The possible values are 'No link', '10M/Link,' or '100M/Link.'
1.3.6.1.4.1.8691.2.8.1.1.5DisplayStringread-onlycurrent
viewLanModuleSpeed
OBJECT-TYPE
The current speed and link status of the the network module's LAN ports, if the module is installed. The value includes two parts. Each part indicates the status of one of the LAN ports. The possible values are 'No link', '10M/Link,' '100M/Link,' or continunous dashes to indicate that the LAN module is not installed.
1.3.6.1.4.1.8691.2.8.1.1.6DisplayStringread-onlycurrent
upTime
OBJECT-TYPE
The time (in human-readable notation) since the system was was last re-initialized.
1.3.6.1.4.1.8691.2.8.1.1.7DisplayStringread-onlycurrent
moduleType
OBJECT-TYPE
The module name currently plugged into the NPort.
1.3.6.1.4.1.8691.2.8.1.1.8DisplayStringread-onlycurrent
basicSetting
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.2
serverSetting
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.2.1
serverName
OBJECT-TYPE
A text string used to identify the NPort.
1.3.6.1.4.1.8691.2.8.1.2.1.1DisplayStringread-writecurrent
serverLocation
OBJECT-TYPE
A text string used to identify the location of the NPort. This option is useful for specifying the location or application of different NPort device servers.
1.3.6.1.4.1.8691.2.8.1.2.1.2DisplayStringread-writecurrent
timeSetting
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.2.2
timeZone
OBJECT-TYPE
The time-zone index of the NPort.
1.3.6.1.4.1.8691.2.8.1.2.2.1INTEGERread-writecurrent
localTime
OBJECT-TYPE
The system time in seconds since 1970/1/1.
1.3.6.1.4.1.8691.2.8.1.2.2.2DateAndTimeread-writecurrent
timeServer
OBJECT-TYPE
The NPort 6000 series device server uses SNTP (RFC-1769) for auto time calibration. Input the correct 'Time server' IP address or domain name. Once the NPort 6000 series device server is configured with the correct Time server address, it will request time information from the Time server every 10 minutes.
1.3.6.1.4.1.8691.2.8.1.2.2.3DisplayStringread-writecurrent
networkSetting
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.3
ipConfiguration
OBJECT-TYPE
The IP configuration mode of the NPort. You can choose from four possible IP configuration modes: Static, DHCP, DHCP/BOOTP, BOOTP, and PPPoE.
1.3.6.1.4.1.8691.2.8.1.3.1INTEGER {static(0), dhcp(1), dhcp-BOOTP(2), bootp(3), pppoe(4)}read-writecurrent
sysIpAddress
OBJECT-TYPE
An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP address to identify and talk to each other over the network. Choose a proper IP address that is unique and valid in your network environment.
1.3.6.1.4.1.8691.2.8.1.3.2IpAddressread-writecurrent
netMask
OBJECT-TYPE
A subnet mask represents all of the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort 6000 series device server will use the subnet mask to check whether the TCP/IP host specified in the packet is on the local network segment. If the address is on the same network segment as the NPort 6000 series device server, a connection is established directly from the NPort 6000 series device server. Otherwise, the connection is established through the given default gateway.
1.3.6.1.4.1.8691.2.8.1.3.3IpAddressread-writecurrent
defaultGateway
OBJECT-TYPE
A gateway is a network computer that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort 6000 series device server needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult with the network administrator.
1.3.6.1.4.1.8691.2.8.1.3.4IpAddressread-onlycurrent
dnsServer1IpAddr
OBJECT-TYPE
The first DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website¡¦s correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection.
1.3.6.1.4.1.8691.2.8.1.3.5IpAddressread-writecurrent
dnsServer2IpAddr
OBJECT-TYPE
The second DNS server address. When the user wants to visit a particular website, the computer asks a Domain Name System (DNS) server for the website¡¦s correct IP address, and then the computer uses the response to connect to the web server. DNS is the way that Internet domain names are identified and translated into IP addresses. A domain name is an alphanumeric name, such as moxa.com, that it is usually easier to remember. A DNS server is a host that translates this kind of text-based domain name into the numeric IP address used to establish a TCP/IP connection.
1.3.6.1.4.1.8691.2.8.1.3.6IpAddressread-writecurrent
pppoeUserAccount
OBJECT-TYPE
The user account used by the NPort to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username and password that they received from their ISP to establish a network connection.
1.3.6.1.4.1.8691.2.8.1.3.7DisplayStringread-writecurrent
pppoePassword
OBJECT-TYPE
The password used by the NPort to access the Internet using PPPoE. For dynamic broad band networks such as xDSL or Cable Modem, users must enter the username and password that they received from their ISP to establish a network connection.
1.3.6.1.4.1.8691.2.8.1.3.8DisplayStringread-writecurrent
winsFunction
OBJECT-TYPE
Enable or disable the WINS server.
1.3.6.1.4.1.8691.2.8.1.3.9INTEGER {disable(0), enable(1)}read-writecurrent
winsServer
OBJECT-TYPE
If a WINS Server is connected to the network, use this field to record the WINS Server¡¦s IP address. TCP/IP uses IP addresses to identify hosts, but users often use symbolic names, such as computer names. The WINS Server, which uses NetBIOS over TCP/IP, contains a dynamic database to map computer names to IP addresses.
1.3.6.1.4.1.8691.2.8.1.3.10IpAddressread-writecurrent
lan1Speed
OBJECT-TYPE
IEEE802.3 Ethernet supports the auto negotiation speed function to get suitable speeds. However, for connecting to some switches/hubs, the communication speed must be fixed at 100 Mbps or 10 Mbps. Users can use this function to fix the communication speed.
1.3.6.1.4.1.8691.2.8.1.3.11INTEGER {auto-Negation(0), tenMbps-Half(1), tenMbps-Full(2), hundredMbps-Half(3), hundredMbps-Full(4)}read-writecurrent
routingProtocol
OBJECT-TYPE
The routing protocol used by the NPort. This value could be none, RIP-1, or RIP-2.
1.3.6.1.4.1.8691.2.8.1.3.12INTEGER {none(0), rip-1(1), rip-2(2)}read-writecurrent
gratuitousArp
OBJECT-TYPE
Enable or disable the gratuitous ARP function. For some applications, users need the NPort 6000 series device server to send broadcast packets to update the ARP table on the server. If the customer enables this function and sets the send period, the NPort 6000 series device server will send broadcast packets periodically.
1.3.6.1.4.1.8691.2.8.1.3.13INTEGER {disable(0), enable(1)}read-writecurrent
gratuitousArpSendPeriod
OBJECT-TYPE
The send period of the gratuitous ARP function.
1.3.6.1.4.1.8691.2.8.1.3.14INTEGERread-writecurrent
portSetting
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4
opModeSetting
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1
opMode
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.1
opModePortTable
OBJECT-TYPE
The serial ports' operation mode table.
1.3.6.1.4.1.8691.2.8.1.4.1.1.1not-accessiblecurrent
opModePortEntry
OBJECT-TYPE
The serial port's operation mode entry.
1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1not-accessiblecurrent
portIndex
OBJECT-TYPE
The serial port index.
1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.1INTEGERread-onlycurrent
portApplication
OBJECT-TYPE
The application of the serial port. Note that changing this setting may also change the operation mode.
1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.2INTEGER {disable(0), dial-InOut(1), terminal(2), reverse-Terminal(3), device-Control(4), printer(6), socket(11), ethernet-Modem(12), pair-Connection(13)}read-writecurrent
portMode
OBJECT-TYPE
The operation mode of the serial port. Note that changing this setting may also change the application.
1.3.6.1.4.1.8691.2.8.1.4.1.1.1.1.3INTEGER {pair-Slave(0), pair-Master(1), aspp(2), raw-PRN(3), slip(4), slipd(5), ppp(6), disable(7), telnetd(8), dynamic(9), tcp-Server(10), lpd-PRN(11), ethernet-Modem(12), tcp-Client(13), udp(14), pppd(15), term-ASC(16), term-BIN(17), reverse-SSH(18), ssh(19), rfc-2217(20)}read-writecurrent
application
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2
deviceControl
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2.1
deviceControlTable
OBJECT-TYPE
The Device Control application table.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1not-accessiblecurrent
deviceControlEntry
OBJECT-TYPE
The Device Control application entry.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1not-accessiblecurrent
deviceControlTcpAliveCheck
OBJECT-TYPE
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.1INTEGERread-writecurrent
deviceControlMaxConnection
OBJECT-TYPE
Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort 6000 series device server, and the Real COM driver on that host will have full control over the port. Max. connection = 1: Allows only a single host¡¦s Real COM driver to open the specific NPort 6000 series device server¡¦s serial port. Max connection = 2 to 8: Allows 2 to 8 hosts¡¦ Real COM drivers to open the specific NPort 6000 series device server¡¦s serial port, at the same time. When multiple hosts¡¦ Real COM drivers open the serial port at the same time, the COM driver only provides a pure data tunnel without control ability. The serial port parameter will use the firmware settings instead of getting the settings from your application program (AP).
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.2INTEGERread-writecurrent
deviceControlIgnoreJammedIp
OBJECT-TYPE
Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.3INTEGER {no(0), yes(1)}read-writecurrent
deviceControlAllowDriverControl
OBJECT-TYPE
If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort 6000 series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.4INTEGER {no(0), yes(1)}read-writecurrent
deviceControlSecure
OBJECT-TYPE
If 'Secure' is enabled, the data on the Ethernet will be encrypted with SSL.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.5INTEGER {no(0), yes(1)}read-writecurrent
deviceControlTcpPort
OBJECT-TYPE
The 'TCP port' is the TCP port that the NPort 6000 series device server uses to listen to connections, and that other devices must use to contact the NPort 6000 series device server.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.6INTEGERread-writecurrent
deviceControlConnectionDownRTS
OBJECT-TYPE
For some applications, serial devices must obtain the Ethernet link status by reading the RTS signal from the NPort 6000 series device server. If this setting is set to 'goes low,' RTS will change its state to low if the Ethernet link is off.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.7INTEGER {always-high(0), goes-low(1)}read-writecurrent
deviceControlConnectionDownDTR
OBJECT-TYPE
For some applications, serial devices must obtain the Ethernet link status by reading the DTR signal from the NPort 6000 series device server. If this setting is set to 'goes low,' DTR will change its state to low if the Ethernet link is off.
1.3.6.1.4.1.8691.2.8.1.4.1.2.1.1.1.8INTEGER {always-high(0), goes-low(1)}read-writecurrent
socket
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2.2
socketTable
OBJECT-TYPE
The Socket application table.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1not-accessiblecurrent
socketEntry
OBJECT-TYPE
The Socket application entry.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1not-accessiblecurrent
socketTcpAliveCheck
OBJECT-TYPE
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection is idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.1INTEGERread-writecurrent
socketInactivityTime
OBJECT-TYPE
0 ms: TCP connection is not closed when the serial line is idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.2INTEGERread-writecurrent
socketMaxConnection
OBJECT-TYPE
Max connection is usually used when the user needs to receive data from different hosts simultaneously. The factory default is 1. In this case, only one specific host can access this port of the NPort 6000 series device server, and the Real COM driver on that host will have full control over the port. Max. connection 1: Allows only a single host¡¦s Real COM driver to open the specific NPort 6000 series device server¡¦s serial port. Max connection 2 to 8: Allows 2 to 8 hosts¡¦ Real COM drivers to open the specific NPort 6000 series device server¡¦s serial port, at the same time. When multiple hosts¡¦ Real COM drivers open the serial port at the same time, the COM driver only provides a pure data tunnel without control ability. The serial port parameter will use the firmware settings instead of depending on your application program (AP).
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.3INTEGERread-writecurrent
socketIgnoreJammedIp
OBJECT-TYPE
Previously, when Max connection was set to a value greater than 1, and the serial device was transmitting data, if any one of the connected hosts stopped responding, the serial device would wait until the data had been transmitted successfully before transmitting the second group of data to all hosts. Currently, if you select Yes for 'Ignore jammed IP,' the host that is not responding will be ignored, but the data will still be transmitted to the other hosts.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.4INTEGER {no(0), yes(1)}read-writecurrent
socketAllowDriverControl
OBJECT-TYPE
If Max connection is greater than 1, NPort will ignore driver control commands from all connected hosts. However, if you set Allow driver control to YES, control commands will be accepted. Note that since the NPort 6000 series device server may get configuration changes from multiple hosts, the most recent command received will take precedence.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.5INTEGER {no(0), yes(1)}read-writecurrent
socketSecure
OBJECT-TYPE
If Secure is enabled, data sent over the Ethernet will be encrypted with SSL.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.6INTEGER {no(0), yes(1)}read-writecurrent
socketTcpPort
OBJECT-TYPE
The 'TCP port' is the TCP port that the NPort 6000 series device server uses to listen to connections, and that other devices must use to contact the NPort 6000 series device server.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.7INTEGERread-writecurrent
socketCmdPort
OBJECT-TYPE
The 'Command port' is a TCP port used to listen for IP-Serial Lib commands from the host. In order to prevent a TCP port conflict with other applications, the user can set the Command port to another port if needed. IP-Serial Lib will automatically check the Command Port on the NPort 6000 series device server to avoid the need for the user to configure the program.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.8INTEGERread-writecurrent
socketTcpServerConnectionDownRTS
OBJECT-TYPE
For some applications, serial devices must obtain the Ethernet link status from the RTS signal sent by the NPort 6000 series device server. If this setting is set to 'goes low,' RTS will change the state to low if the Ethernet link is off.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.9INTEGER {always-high(0), goes-low(1)}read-writecurrent
socketTcpServerConnectionDownDTR
OBJECT-TYPE
For some applications, serial devices must obtain the Ethernet link status from the DTR signal sent by the NPort 6000 series device server. If this setting is set to 'goes low,' DTR will change the state to low if the Ethernet link is off.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.10INTEGER {always-high(0), goes-low(1)}read-writecurrent
socketTcpClientDestinationAddress1
OBJECT-TYPE
The NPort 6000 series device server can connect actively to a remote host that has this IP address.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.11DisplayStringread-writecurrent
socketTcpClientDestinationPort1
OBJECT-TYPE
The NPort 6000 series device server can connect actively to a remote host that has this TCP port number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.12INTEGERread-writecurrent
socketTcpClientDestinationAddress2
OBJECT-TYPE
The NPort 6000 series device server can connect actively to a remote host that has this IP address.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.13DisplayStringread-writecurrent
socketTcpClientDestinationPort2
OBJECT-TYPE
The NPort 6000 series device server can connect actively to a remote host that has this TCP port number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.14INTEGERread-writecurrent
socketTcpClientDestinationAddress3
OBJECT-TYPE
The NPort 6000 series device server can connect actively to a remote host that has this IP address.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.15DisplayStringread-writecurrent
socketTcpClientDestinationPort3
OBJECT-TYPE
The NPort 6000 series device server can connect actively to a remote host that has this port number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.16INTEGERread-writecurrent
socketTcpClientDestinationAddress4
OBJECT-TYPE
The NPort 6000 series device server can connect actively to a remote host that has this IP address.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.17DisplayStringread-writecurrent
socketTcpClientDestinationPort4
OBJECT-TYPE
The NPort 6000 series device server can connect actively to a remote host that has this port number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.18INTEGERread-writecurrent
socketTcpClientDesignatedLocalPort1
OBJECT-TYPE
The local TCP port used to connect actively to the remote host.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.19INTEGERread-writecurrent
socketTcpClientDesignatedLocalPort2
OBJECT-TYPE
The local TCP port used to connect actively to the remote host.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.20INTEGERread-writecurrent
socketTcpClientDesignatedLocalPort3
OBJECT-TYPE
The local TCP port used to connect actively to the remote host.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.21INTEGERread-writecurrent
socketTcpClientDesignatedLocalPort4
OBJECT-TYPE
The local TCP port used to connect actively to the remote host.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.22INTEGERread-writecurrent
socketTcpClientConnectionControl
OBJECT-TYPE
Events that cause the TCP client to drop the connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.23INTEGER {startup-None(257), anyCharacter-None(258), dsrOn-None(260), dcdOn-None(264), anyCharacter-InactivityTime(514), dsrOn-DSR-Off(1028), dcdOn-DCD-Off(2056)}read-writecurrent
socketUdpDestinationAddress1Begin
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress1End.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.24IpAddressread-writecurrent
socketUdpDestinationAddress1End
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress1Begin and this parameter.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.25IpAddressread-writecurrent
socketUdpDestinationPort1
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts that have this port number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.26INTEGERread-writecurrent
socketUdpDestinationAddress2Begin
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress2End.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.27IpAddressread-writecurrent
socketUdpDestinationAddress2End
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to the remote hosts whose IP addresses are in the range between socketUdpDestinationAddress2Begin and this parameter.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.28IpAddressread-writecurrent
socketUdpDestinationPort2
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to the remote hosts that have this TCP port number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.29INTEGERread-writecurrent
socketUdpDestinationAddress3Begin
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress3End.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.30IpAddressread-writecurrent
socketUdpDestinationAddress3End
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress3Begin and this parameter.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.31IpAddressread-writecurrent
socketUdpDestinationPort3
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts that have this TCP port number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.32INTEGERread-writecurrent
socketUdpDestinationAddress4Begin
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between this parameter and socketUdpDestinationAddress4End.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.33IpAddressread-writecurrent
socketUdpDestinationAddress4End
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts whose IP addresses are in the range between socketUdpDestinationAddress4Begin and this parameter.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.34IpAddressread-writecurrent
socketUdpDestinationPort4
OBJECT-TYPE
The NPort 6000 series device server can actively send UDP packets to remote hosts that have this TCP port number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.35INTEGERread-writecurrent
socketUdpLocalListenPort
OBJECT-TYPE
The UDP port that the NPort 6000 series device server listens to and that other devices must use to contact the NPort 6000 series device server.
1.3.6.1.4.1.8691.2.8.1.4.1.2.2.1.1.36INTEGERread-writecurrent
pairConnection
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2.3
pairConnectionTable
OBJECT-TYPE
The Pair Connection table.
1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1not-accessiblecurrent
pairConnectionEntry
OBJECT-TYPE
The Pair Connection entry.
1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1not-accessiblecurrent
pairConnectionTcpAliveCheck
OBJECT-TYPE
The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.1INTEGERread-writecurrent
pairConnectionSecure
OBJECT-TYPE
If Secure is enabled, the Ethernet data will be encrypted using SSL.
1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.2INTEGER {no(0), yes(1)}read-writecurrent
pairConnectionDestinationAddress
OBJECT-TYPE
The Pair Connection 'Master' will contact the network host that has the specified IP address.
1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.3DisplayStringread-writecurrent
pairConnectionDestinationPort
OBJECT-TYPE
Data will be transmitted through the specified port number. Note that you must configure the same TCP port number for the device server acting as the Pair Connection 'Slave.'
1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.4INTEGERread-writecurrent
pairConnectionTcpPort
OBJECT-TYPE
This port number must be the same port number that was set up for the Pair Connection 'Master' device server.
1.3.6.1.4.1.8691.2.8.1.4.1.2.3.1.1.5INTEGERread-writecurrent
ethernetModem
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2.4
ethernetModemTable
OBJECT-TYPE
The Ethernet Modem table.
1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1not-accessiblecurrent
ethernetModemEntry
OBJECT-TYPE
The Ethernet Modem entry.
1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1not-accessiblecurrent
ethernetModemTcpAliveCheck
OBJECT-TYPE
The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.1INTEGERread-writecurrent
ethernetModemTcpPort
OBJECT-TYPE
The local TCP port used to listen for incoming calls from a remote ethernet modem.
1.3.6.1.4.1.8691.2.8.1.4.1.2.4.1.1.2INTEGERread-writecurrent
terminal
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2.5
terminalTable
OBJECT-TYPE
The Terminal Application table.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1not-accessiblecurrent
terminalEntry
OBJECT-TYPE
The Terminal Application entry.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1not-accessiblecurrent
terminalTcpAliveCheck
OBJECT-TYPE
The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection from another host.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.1INTEGERread-writecurrent
terminalInactivityTime
OBJECT-TYPE
0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another host's TCP connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.2INTEGERread-writecurrent
terminalAutoLinkProtocol
OBJECT-TYPE
If Auto-Link protocol is set to 'None,' the NPort 6000 series device server will not connect to the host automatically. If Auto-Link protocol is set to 'Telnet,' the NPort 6000 series device server will connect to the host automatically using Telnet. If Auto-Link protocol is set to 'Rlogin,' the NPort 6000 series device server will connect to the host automatically using rlogin.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.3INTEGER {none(0), telnet(1), rlogin(2)}read-writecurrent
terminalPrimaryHostAddress
OBJECT-TYPE
If specified, designates a 'permanent' host to which the terminal will always be connected.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.4DisplayStringread-writecurrent
terminalSecondHostAddress
OBJECT-TYPE
If specified, designates a 'permanent' host to which the terminal will always be connected.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.5DisplayStringread-writecurrent
terminalTelnetTcpPort
OBJECT-TYPE
By default, the Telnet TCP port number is set to 23, which is the default TCP port number for Telnet. If you need to telnet to this NPort 6000 series device server's serial port, set the Telnet TCP port to a different number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.6INTEGERread-writecurrent
terminalSshTcpPort
OBJECT-TYPE
By default, the SSH TCP port number is set to 22, which is the default TCP port number for SSH. If you need to use SSH to connect to this NPort 6000 series device server's serial port, set the Telnet TCP port to a different number.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.7INTEGERread-writecurrent
terminalType
OBJECT-TYPE
Defines the terminal type for outgoing connections.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.8DisplayStringread-writecurrent
terminalMaxSessions
OBJECT-TYPE
Configure the max. number of sessions.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.9INTEGERread-writecurrent
terminalChangeSession
OBJECT-TYPE
Defines the control character used to change the terminal session.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.10DisplayStringread-writecurrent
terminalQuit
OBJECT-TYPE
Defines the control character used to quit a terminal session.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.11DisplayStringread-writecurrent
terminalBreak
OBJECT-TYPE
Defines the control character used to send a Telnet BREAK message.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.12DisplayStringread-writecurrent
terminalInterrupt
OBJECT-TYPE
Defines the control character used to send a Telnet INTERRUPT message.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.13DisplayStringread-writecurrent
terminalAuthenticationType
OBJECT-TYPE
The terminal authentication type.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.14INTEGER {none(0), local(1), radius(2)}read-writecurrent
terminalAutoLoginPrompt
OBJECT-TYPE
The prompt string for the automatic login ID. When the NPort 6000 series device server receives this string from a remote telnet/rlogin server, it will automatically reply with the user ID.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.15DisplayStringread-writecurrent
terminalPasswordPrompt
OBJECT-TYPE
The prompt string for the automatic login password. When the NPort 6000 series device server receives this string from a remote telnet/rlogin server, it will automatically reply with the user password.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.16DisplayStringread-writecurrent
terminalLoginUserName
OBJECT-TYPE
Terminal login ID for automatic login.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.17DisplayString (SIZE(0..16))read-writecurrent
terminalLoginPassword
OBJECT-TYPE
Terminal login password for automatic login.
1.3.6.1.4.1.8691.2.8.1.4.1.2.5.1.1.18DisplayString (SIZE(0..16))read-writecurrent
reverseTerminal
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2.6
reverseTerminalTable
OBJECT-TYPE
The Reverse Terminal Application table.
1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1not-accessiblecurrent
reverseTerminalEntry
OBJECT-TYPE
The Reverse Terminal Application entry.
1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1not-accessiblecurrent
reverseTerminalTcpAliveCheck
OBJECT-TYPE
The TCP alive check time. 0 min: TCP connection will not be closed when the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.1INTEGERread-writecurrent
reverseTerminalInactivityTime
OBJECT-TYPE
0 min: TCP connection will not be closed if the serial line becomes idle. 0-99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.2INTEGERread-writecurrent
reverseTerminalTcpPort
OBJECT-TYPE
Each of the NPort 6000 series device server's serial ports are mapped to a TCP port.
1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.3INTEGERread-writecurrent
reverseTerminalAuthenticationType
OBJECT-TYPE
The reverse terminal authentication type.
1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.4INTEGER {none(0), local(1), radius(2)}read-writecurrent
reverseTerminalMapKeys
OBJECT-TYPE
If data received through NPort 6000 series device server's Ethernet port is sent using the 'enter' command, the data will be transmitted out through the serial port with an added 1. 'carriage return + line feed' if you select the 'cr-lf' option (i.e., the cursor will jump to the next line, and return to the first character of the line) 2. 'carriage return' if you select the 'cr' option (i.e., the cursor will return to the first character of the line 3. 'line feed' if you select the 'lf' option. (i.e., the cursor will jump to the next line, but not move horizontally)
1.3.6.1.4.1.8691.2.8.1.4.1.2.6.1.1.5INTEGER {cr-lf(0), cr(1), lf(2)}read-writecurrent
printer
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2.7
printerTable
OBJECT-TYPE
The Printer Application table.
1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1not-accessiblecurrent
printerEntry
OBJECT-TYPE
The Printer Application entry.
1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1not-accessiblecurrent
printerTcpAliveCheck
OBJECT-TYPE
The TCP alive check time. 0 min: TCP connection will not be closed if the TCP connection becomes idle. 1 to 99 min: The NPort 6000 series device server automatically closes the TCP connection if there is no TCP activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another Real COM driver Connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.1INTEGERread-writecurrent
printerTcpPort
OBJECT-TYPE
The host uses this value to determine the Group to which the printer attached to this serial port belongs. These values are fixed, and cannot be changed by the user.
1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.2INTEGERread-onlycurrent
printerGroup
OBJECT-TYPE
Groups printers attached to different ports. Printers in the same group will share the printing load for printing requests to that group of printers. E.g., setting the NPort 6000 series device server's serial ports 1, 3, and 6 for 'Group01' will allow the printers attached to these three ports to act essentially as one printer.
1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.3INTEGER {group1(0), group2(1), group3(2), group4(3), group5(4), group6(5), group7(6), group8(7), group9(8), group10(9), group11(10), group12(11), group13(12), group14(13), group15(14), group16(15)}read-writecurrent
printerQueueNameRaw
OBJECT-TYPE
Specify the name of the print queue (in RAW mode).
1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.4DisplayStringread-writecurrent
printerQueueNameASCII
OBJECT-TYPE
Specify the name of the print queue (in ASCII mode).
1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.5DisplayStringread-writecurrent
printerAppendFromFeed
OBJECT-TYPE
Specify paging.
1.3.6.1.4.1.8691.2.8.1.4.1.2.7.1.1.6INTEGER {disable(0), enable(1)}read-writecurrent
dial
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.2.8
dialTable
OBJECT-TYPE
The Dial In/Out table.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1not-accessiblecurrent
dialEntry
OBJECT-TYPE
The Dial In/Out entry.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1not-accessiblecurrent
dialTERMBINMode
OBJECT-TYPE
Select Yes to enable a Binary Terminal connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.1INTEGER {no(0), yes(1)}read-writecurrent
dialPPPDMode
OBJECT-TYPE
Select Yes to enable a PPPD connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.2INTEGER {no(0), yes(1)}read-writecurrent
dialSLIPDMode
OBJECT-TYPE
Select Yes to enable a SLIPD Terminal connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.3INTEGER {no(0), yes(1)}read-writecurrent
dialAuthType
OBJECT-TYPE
The dial in/out authentication type.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.4INTEGER {none(0), local(1), radius(2)}read-writecurrent
dialDisconnectBy
OBJECT-TYPE
If this field is set to 'dcd-off,' the connection will be disconnected when the DCD signal is off. If this field is set to 'dsr-off,' the connection will be disconnected when the DSR signal is off.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.5INTEGER {none(0), dcd-off(2), dsr-off(4)}read-writecurrent
dialDestinationIpAddress
OBJECT-TYPE
Destination IP address is the IP address of the remote dial-in/dial-out server.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.6IpAddressread-writecurrent
dialSourceIpAddress
OBJECT-TYPE
Source IP address is IP address of this serial port. The NPort 6000 series device server will automatically assign an IP address for the port. We recommend leaving this field blank.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.7IpAddressread-writecurrent
dialIpNetmask
OBJECT-TYPE
The IP netmask used for dial-in/dial-out networks (PPP or SLIP).
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.8IpAddressread-writecurrent
dialTcpIpCompression
OBJECT-TYPE
Depends on whether the remote user's application requests compression.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.9INTEGER {no(0), yes(1)}read-writecurrent
dialInactivityTime
OBJECT-TYPE
0 ms: TCP connection will not be closed if the serial line becomes idle. 1-65535 ms: The NPort 6000 series device server automatically closes the TCP connection if there is no serial data activity for the given time. After the connection is closed, the NPort 6000 series device server starts listening for another TCP connection.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.10INTEGERread-writecurrent
dialLinkQualityReport
OBJECT-TYPE
Choose YES if you are using software to collect Link quality information.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.11INTEGER {no(0), yes(1)}read-writecurrent
dialOutgoingPAPID
OBJECT-TYPE
Dial-out user ID account.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.12DisplayStringread-writecurrent
dialPAPPassword
OBJECT-TYPE
Dial-out user password.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.13DisplayStringread-writecurrent
dialIncomingPAPCheck
OBJECT-TYPE
The Dial in/out incoming PAP check type.
1.3.6.1.4.1.8691.2.8.1.4.1.2.8.1.1.14INTEGER {none(0), local(1), radius(2)}read-writecurrent
dataPacking
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.1.3
dataPackingPortTable
OBJECT-TYPE
The Data Packing table.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1not-accessiblecurrent
dataPackingPortEntry
OBJECT-TYPE
The Data Packing entry.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1not-accessiblecurrent
portPacketLength
OBJECT-TYPE
If the value is 0, the Delimiter Process will be used, regardless of the length of the data packet. If the data length (in bytes) matches the configured value, the data will be forced out. The data length can be configured from 0 to 1024 bytes. Set to 0 if you do not need to limit the length.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.1INTEGERread-writecurrent
portDelimiter1Enable
OBJECT-TYPE
Enable the first delimiter character.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.2INTEGER {disable(0), enable(1)}read-writecurrent
portDelimiter1
OBJECT-TYPE
The first delimiter character, in hex decimal.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.3DisplayString (SIZE(0..2))read-writecurrent
portDelimiter2Enable
OBJECT-TYPE
Enable the second delimiter character.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.4INTEGER {disable(0), enable(1)}read-writecurrent
portDelimiter2
OBJECT-TYPE
The second delimiter character, in hex decimal.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.5DisplayString (SIZE(0..2))read-writecurrent
portDelimiterProcess
OBJECT-TYPE
'delimiterAddOne' or 'delimiterAddTwo': The data will be transmitted when an additional byte (for 'delimiterAddOne'), or an additional 2 bytes (for 'delimiterAddTwo') of data is received after receiving the Delimiter. 'stripDelimiter': When the delimiter is received, the Delimiter is deleted (i.e., stripped), and the remaining data is transmitted. 'doNothing': The data will be transmitted when the delimiter is received.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.6INTEGER {doNothing(1), delimiterAddOne(2), delimiterAddTwo(4), stripDelimiter(8)}read-writecurrent
portForceTransmit
OBJECT-TYPE
0: Disable the force transmit timeout. 1 to 65535: Forces the NPort 6000 series device server's TCP/IP protocol software to try to pack serial data received during the specified time into the same data frame.
1.3.6.1.4.1.8691.2.8.1.4.1.3.1.1.7INTEGERread-writecurrent
comParamSetting
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.2
comParamPortTable
OBJECT-TYPE
The Communication Parameters table.
1.3.6.1.4.1.8691.2.8.1.4.2.1not-accessiblecurrent
comParamPortEntry
OBJECT-TYPE
The Communication Parameters entry.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1not-accessiblecurrent
portAlias
OBJECT-TYPE
Port alias is included to allow easy identification of the serial devices that are connected to NPort 6000 series device server's serial port.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.1DisplayString (SIZE(0..16))read-writecurrent
portInterface
OBJECT-TYPE
The serial interface that the port works on.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.2INTEGER {rs-232(0), rs-422(1), rs-485-2-wire(2), rs-485-4-wire(3)}read-writecurrent
portBaudRate
OBJECT-TYPE
The port's speed in bits per second. You can choose a standard baud rate by indexing.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.3INTEGER {b50(0), b75(1), b110(2), b134(3), b150(4), b300(5), b600(6), b1200(7), b1800(8), b2400(9), b4800(10), b7200(11), b9600(12), b19200(13), b38400(14), b57600(15), b115200(16), b230400(17), b460800(18), b921600(19)}read-writecurrent
portBaudRateManual
OBJECT-TYPE
The port's speed in bits per second. You can specify a baud rate manually.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.4INTEGERread-writecurrent
portDataBits
OBJECT-TYPE
The number of bits in a character for the port.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.5INTEGER {d5(0), d6(1), d7(2), d8(3)}read-writecurrent
portStopBits
OBJECT-TYPE
The number of stop bits for the port.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.6INTEGER {s1(0), s15(1), s2(2)}read-writecurrent
portParity
OBJECT-TYPE
The parity bit for the port.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.7INTEGER {none(0), odd(1), even(2), mark(3), space(4)}read-writecurrent
portFlowControl
OBJECT-TYPE
The flow-control method for the port.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.8INTEGER {none(0), rts-cts(1), xon-xoff(2), dtr-dsr(3)}read-writecurrent
portFIFO
OBJECT-TYPE
Enable or disable the port's FIFO.
1.3.6.1.4.1.8691.2.8.1.4.2.1.1.9INTEGER {disable(0), enable(1)}read-writecurrent
dataBuffering
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.3
dataBufferingPortTable
OBJECT-TYPE
The Data Buffering/Log table.
1.3.6.1.4.1.8691.2.8.1.4.3.1not-accessiblecurrent
dataBufferingPortEntry
OBJECT-TYPE
The Data Buffering/Log entry.
1.3.6.1.4.1.8691.2.8.1.4.3.1.1not-accessiblecurrent
portBufferingEnable
OBJECT-TYPE
Enable off-line port buffering.
1.3.6.1.4.1.8691.2.8.1.4.3.1.1.1INTEGER {no(0), yes(1)}read-writecurrent
portBufferingLocation
OBJECT-TYPE
The location of off-line port buffering.
1.3.6.1.4.1.8691.2.8.1.4.3.1.1.2INTEGER {memory(0), sdCard(1)}read-writecurrent
portBufferingSDFileSize
OBJECT-TYPE
The maximum file size of off-line port buffering, in MBytes, if the location is set to 'sdCard.'
1.3.6.1.4.1.8691.2.8.1.4.3.1.1.3INTEGERread-writecurrent
portSerialDataLoggingEnable
OBJECT-TYPE
Enable or disable serial data logging for the port.
1.3.6.1.4.1.8691.2.8.1.4.3.1.1.4INTEGER {no(0), yes(1)}read-writecurrent
modemSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.4
modemSettingsPortTable
OBJECT-TYPE
The Modem Settings table.
1.3.6.1.4.1.8691.2.8.1.4.4.1not-accessiblecurrent
modemSettingsPortEntry
OBJECT-TYPE
The Modem Settings entry.
1.3.6.1.4.1.8691.2.8.1.4.4.1.1not-accessiblecurrent
portEnableModem
OBJECT-TYPE
Enable or disable modem for this port.
1.3.6.1.4.1.8691.2.8.1.4.4.1.1.1INTEGER {disable(0), enable(1)}read-writecurrent
portInitialString
OBJECT-TYPE
Set the modem's initial string to establish the connection. E.g., 'AT&S0=1' for auto-answer.
1.3.6.1.4.1.8691.2.8.1.4.4.1.1.2DisplayString (SIZE(0..24))read-writecurrent
portDialUp
OBJECT-TYPE
Set the modem's dial-up AT command string.
1.3.6.1.4.1.8691.2.8.1.4.4.1.1.3DisplayString (SIZE(0..8))read-writecurrent
portPhoneNumber
OBJECT-TYPE
Set the number used to dial out.
1.3.6.1.4.1.8691.2.8.1.4.4.1.1.4DisplayString (SIZE(0..16))read-writecurrent
welcomeMessage
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.4.5
portEnableWelcomeMessage
OBJECT-TYPE
Enable or disable the welcome message.
1.3.6.1.4.1.8691.2.8.1.4.5.1INTEGER {disable(0), enable(1)}read-writecurrent
portMessage
OBJECT-TYPE
Set up a welcome message to greet dial-in users.
1.3.6.1.4.1.8691.2.8.1.4.5.2DisplayString (SIZE(0..1280))read-writecurrent
sysManagement
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5
miscNetworkSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1
accessibleIp
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1.1
enableAccessibleIpList
OBJECT-TYPE
Enable or disable the entire accessible IP list.
1.3.6.1.4.1.8691.2.8.1.5.1.1.1INTEGER {disable(0), enable(1)}read-writecurrent
accessibleIpListTable
OBJECT-TYPE
Accessible IP List table.
1.3.6.1.4.1.8691.2.8.1.5.1.1.2not-accessiblecurrent
accessibleIpListEntry
OBJECT-TYPE
Accessible IP List entry.
1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1not-accessiblecurrent
accessibleIpListIndex
OBJECT-TYPE
Accessible IP List index.
1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.1INTEGERread-onlycurrent
activeAccessibleIpList
OBJECT-TYPE
Enable or disable this accessible IP entry.
1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.2INTEGER {disable(0), enable(1)}read-writecurrent
accessibleIpListAddress
OBJECT-TYPE
Accessible IP address. This value can be the IP address of a single host if the netmask is set to '255.255.255.255,' or it can be a network address.
1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.3IpAddressread-writecurrent
accessibleIpListNetmask
OBJECT-TYPE
Accessible IP address netmask. The IP address and netmask are used to specify a group of remote hosts.
1.3.6.1.4.1.8691.2.8.1.5.1.1.2.1.4IpAddressread-writecurrent
snmpAgentSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1.2
snmpEnable
OBJECT-TYPE
Enable or disable SNMP agent.
1.3.6.1.4.1.8691.2.8.1.5.1.2.1INTEGER {disable(0), enable(1)}read-writecurrent
snmpContactName
OBJECT-TYPE
The SNMP contact information usually includes an emergency contact name and telephone or pager number.
1.3.6.1.4.1.8691.2.8.1.5.1.2.2DisplayString (SIZE(0..40))read-writecurrent
snmpLocation
OBJECT-TYPE
Specify the location string for SNMP agents, such as the NPort 6000 series device server. This string is usually set to the street address where the NPort 6000 series device server is physically located.
1.3.6.1.4.1.8691.2.8.1.5.1.2.3DisplayString (SIZE(0..40))read-writecurrent
dDNS
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1.3
dDNSEnable
OBJECT-TYPE
Enable or disable the DDNS function.
1.3.6.1.4.1.8691.2.8.1.5.1.3.1INTEGER {disable(0), enable(1)}read-writecurrent
dDNSServerAddress
OBJECT-TYPE
The DDNS server address. The DDNS is serviced by a 3-party provider. To use the DDNS function, you may need to obtain a user account from the server.
1.3.6.1.4.1.8691.2.8.1.5.1.3.2INTEGER {dynDns_org(0)}read-writecurrent
dDNSHostName
OBJECT-TYPE
The host name of the machine to be registered to the DDNS server.
1.3.6.1.4.1.8691.2.8.1.5.1.3.3DisplayString (SIZE(0..60))read-writecurrent
dDNSUserName
OBJECT-TYPE
The user account provided by the DDNS server.
1.3.6.1.4.1.8691.2.8.1.5.1.3.4DisplayString (SIZE(0..60))read-writecurrent
dDNSPassword
OBJECT-TYPE
The user password provided by the DDNS server.
1.3.6.1.4.1.8691.2.8.1.5.1.3.5DisplayString (SIZE(0..60))read-writecurrent
hostTable
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1.4
hostTableTable
OBJECT-TYPE
Host Table.
1.3.6.1.4.1.8691.2.8.1.5.1.4.1not-accessiblecurrent
hostTableEntry
OBJECT-TYPE
Host Table entry.
1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1not-accessiblecurrent
hostTableIndex
OBJECT-TYPE
The Host Table index.
1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.1INTEGERread-onlycurrent
hostName
OBJECT-TYPE
The host name of the host table entry.
1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.2DisplayString (SIZE(0..16))read-writecurrent
hostIpAddress
OBJECT-TYPE
Related IP address of the host table entry.
1.3.6.1.4.1.8691.2.8.1.5.1.4.1.1.3IpAddressread-writecurrent
routeTable
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1.5
routeTableTable
OBJECT-TYPE
Route Table.
1.3.6.1.4.1.8691.2.8.1.5.1.5.1not-accessiblecurrent
routeTableEntry
OBJECT-TYPE
Route Table entry.
1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1not-accessiblecurrent
routeTableIndex
OBJECT-TYPE
The Route Table index.
1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.1INTEGERread-onlycurrent
gatewayRouteTable
OBJECT-TYPE
The gateway property of the route table entry.
1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.2IpAddressread-writecurrent
destinationRouteTable
OBJECT-TYPE
The destination IP address of the route table entry. This value can be the IP address of a single host if the netmask set to '255.255.255.255,' or it can be a network address.
1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.3IpAddressread-writecurrent
netmaskRouteTable
OBJECT-TYPE
The destination netmask of the route table entry.
1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.4IpAddressread-writecurrent
metricRouteTable
OBJECT-TYPE
The routing metric for this route. The semantics of this metric are determined by the routing-protocol. Normally, it represents the cost for the destination.
1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.5INTEGERread-writecurrent
interfaceRouteTable
OBJECT-TYPE
The value that identifies the local interface through which the next hop of this route should be reached.
1.3.6.1.4.1.8691.2.8.1.5.1.5.1.1.6INTEGER {port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), lan(256)}read-writecurrent
userTable
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1.6
userTableTable
OBJECT-TYPE
User Table.
1.3.6.1.4.1.8691.2.8.1.5.1.6.1not-accessiblecurrent
userTableEntry
OBJECT-TYPE
User Table entry.
1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1not-accessiblecurrent
userTableIndex
OBJECT-TYPE
The User Table index.
1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.1INTEGERread-onlycurrent
userNameUserTable
OBJECT-TYPE
The user name of this entry.
1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.2DisplayString (SIZE(0..16))read-writecurrent
passwordUserTable
OBJECT-TYPE
The password of this user entry.
1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.3DisplayString (SIZE(0..16))read-writecurrent
phoneNumberUserTable
OBJECT-TYPE
The phone number of this user entry.
1.3.6.1.4.1.8691.2.8.1.5.1.6.1.1.4DisplayString (SIZE(0..16))read-writecurrent
authenticationServer
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1.7
radiusServerIp
OBJECT-TYPE
The IP address or domain name of the RADIUS server.
1.3.6.1.4.1.8691.2.8.1.5.1.7.1DisplayStringread-writecurrent
radiusKey
OBJECT-TYPE
RADIUS password. Must be the same as in the RADIUS server.
1.3.6.1.4.1.8691.2.8.1.5.1.7.2DisplayString (SIZE(0..16))read-writecurrent
udpPortAuthenticationServer
OBJECT-TYPE
The UDP port of the RADIUS server.
1.3.6.1.4.1.8691.2.8.1.5.1.7.3INTEGER {port1645(1645), port1812(1812)}read-writecurrent
radiusAccounting
OBJECT-TYPE
Enable or disable RADIUS accounting.
1.3.6.1.4.1.8691.2.8.1.5.1.7.4INTEGER {disable(0), enable(1)}read-writecurrent
sysLogSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.1.8
sysLocalLog
OBJECT-TYPE
Log the following events to the system log: System Cold Start, System Warm Start.
1.3.6.1.4.1.8691.2.8.1.5.1.8.1INTEGER {disable(0), enable(1)}read-writecurrent
networkLocalLog
OBJECT-TYPE
Log the following events to the system log: DHCP/BOOTP/PPPoE Get IP/Renew, NTP, Mail Fail, NTP Connect Fail, DHCP Fail, IP Conflict, Ethernet Link Down.
1.3.6.1.4.1.8691.2.8.1.5.1.8.2INTEGER {disable(0), enable(1)}read-writecurrent
configLocalLog
OBJECT-TYPE
Log the following events to the system log: Login Fail, IP Changed, Password Changed, Config Changed, Firmware Upgrade, SSL Key Import, Config Import, Config Export.
1.3.6.1.4.1.8691.2.8.1.5.1.8.3INTEGER {disable(0), enable(1)}read-writecurrent
opModeLocalLog
OBJECT-TYPE
Log the following op-mode events to the system log: Connect, Disconnect, Authentication Fail, Restart.
1.3.6.1.4.1.8691.2.8.1.5.1.8.4INTEGER {disable(0), enable(1)}read-writecurrent
autoWarningSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.2
eventSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.2.1
mailWarningColdStart
OBJECT-TYPE
Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatically issue an auto warning message by e-mail after booting up.
1.3.6.1.4.1.8691.2.8.1.5.2.1.1INTEGER {disable(0), enable(1)}read-writecurrent
mailWarningWarmStart
OBJECT-TYPE
Refers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send an e-mail after rebooting.
1.3.6.1.4.1.8691.2.8.1.5.2.1.2INTEGER {disable(0), enable(1)}read-writecurrent
mailWarningAuthFailure
OBJECT-TYPE
The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately send an e-mail.
1.3.6.1.4.1.8691.2.8.1.5.2.1.3INTEGER {disable(0), enable(1)}read-writecurrent
mailWarningIpChanged
OBJECT-TYPE
The user has changed the NPort 6000 series device server's IP address. When the IP address changes, the NPort 6000 series device server will send an e-mail with the new IP address before it reboots. If the NPort 6000 series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning.
1.3.6.1.4.1.8691.2.8.1.5.2.1.4INTEGER {disable(0), enable(1)}read-writecurrent
mailWarningPasswordChanged
OBJECT-TYPE
The user has changed the NPort 6000 series device server's password. When the password changes, the NPort 6000 series device server will send an e-mail with the password changed notice before it reboots. If the NPort 6000 series device server is unable to send an e-mail message to the mail server within 15 seconds, it will reboot anyway, and abort the e-mail auto warning.
1.3.6.1.4.1.8691.2.8.1.5.2.1.5INTEGER {disable(0), enable(1)}read-writecurrent
trapServerColdStart
OBJECT-TYPE
Refers to starting the system from power off (contrast this with warm start). When performing a cold start, the NPort 6000 series device server will automatically issue an auto warning message by sending an SNMP trap after booting up.
1.3.6.1.4.1.8691.2.8.1.5.2.1.6INTEGER {disable(0), enable(1)}read-writecurrent
trapServerWarmStart
OBJECT-TYPE
Refers to restarting the NPort 6000 without turning the power off. When performing a warm start, the NPort 6000 series device server will automatically send an SNMP trap after rebooting.
1.3.6.1.4.1.8691.2.8.1.5.2.1.7INTEGER {disable(0), enable(1)}read-writecurrent
trapServerAuthFailure
OBJECT-TYPE
The user inputs a wrong password from the Console or Administrator. When authentication failure occurs, the NPort 6000 series device server will immediately send an SNMP trap.
1.3.6.1.4.1.8691.2.8.1.5.2.1.8INTEGER {disable(0), enable(1)}read-writecurrent
alarmServerEthernet1LinkDown
OBJECT-TYPE
When the built-in link1 port is off, the NPort 6000 series device server will automatically raise a d-out alarm.
1.3.6.1.4.1.8691.2.8.1.5.2.1.9INTEGER {disable(0), enable(1)}read-writecurrent
alarmServerEthernet2LinkDown
OBJECT-TYPE
The NPort 6000 series device server can provide an extra Ethernet port via the network module. When the first port on the network module is off, the NPort 6000 series device server will automatically raise a d-out alarm.
1.3.6.1.4.1.8691.2.8.1.5.2.1.10INTEGER {disable(0), enable(1)}read-writecurrent
alarmServerEthernet3LinkDown
OBJECT-TYPE
The NPort 6000 series device server can provide an extra Ethernet port via the network module. When the second port on the network module is off, the NPort 6000 series device server will automatically raise a d-out alarm.
1.3.6.1.4.1.8691.2.8.1.5.2.1.11INTEGER {disable(0), enable(1)}read-writecurrent
serialEventSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.2.2
portEventSettingsTable
OBJECT-TYPE
Port Event Settings Table.
1.3.6.1.4.1.8691.2.8.1.5.2.2.1not-accessiblecurrent
portEventSettingsEntry
OBJECT-TYPE
Port Event Settings entry.
1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1not-accessiblecurrent
mailDCDchange
OBJECT-TYPE
A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately send an e-mail message.
1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.1INTEGER {disable(0), enable(1)}read-writecurrent
trapDCDchange
OBJECT-TYPE
A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately send an SNMP trap.
1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.2INTEGER {disable(0), enable(1)}read-writecurrent
alarmDCDchange
OBJECT-TYPE
A change in the DCD (Data Carrier Detect) signal indicates that the modem connection status has changed. For example, if the DCD signal changes to low, it indicates that the connection line is down. When the DCD signal changes to low, the NPort 6000 series device server will immediately raise a d-out alarm.
1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.3INTEGER {disable(0), enable(1)}read-writecurrent
mailDSRchange
OBJECT-TYPE
A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately send an e-mail message.
1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.4INTEGER {disable(0), enable(1)}read-writecurrent
trapDSRchange
OBJECT-TYPE
A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately send an SNMP trap.
1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.5INTEGER {disable(0), enable(1)}read-writecurrent
alarmDSRchange
OBJECT-TYPE
A change in the DSR (Data Set Ready) signal indicates that the data communication equipment is powered off. For example, if the DSR signal changes to low, it indicates that the data communication equipment is powered down. When the DSR signal changes to low, the NPort 6000 series device server will immediately raise a d-out alarm.
1.3.6.1.4.1.8691.2.8.1.5.2.2.1.1.6INTEGER {disable(0), enable(1)}read-writecurrent
emailAlert
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.2.3
emailWarningMailServer
OBJECT-TYPE
The e-mail server's IP address or domain name of the e-mail warning function.
1.3.6.1.4.1.8691.2.8.1.5.2.3.1DisplayStringread-writecurrent
emailRequiresAuthentication
OBJECT-TYPE
Set if the mail server requires user login.
1.3.6.1.4.1.8691.2.8.1.5.2.3.2INTEGER {non-require(0), require(1)}read-writecurrent
emailWarningUserName
OBJECT-TYPE
The user name used to log into the mail server if authentication is required.
1.3.6.1.4.1.8691.2.8.1.5.2.3.3DisplayStringread-writecurrent
emailWarningPassword
OBJECT-TYPE
The password used to log into the mail server if authentication is required.
1.3.6.1.4.1.8691.2.8.1.5.2.3.4DisplayStringread-writecurrent
emailWarningFromEmail
OBJECT-TYPE
The e-mail address to be filled in the 'From' field of the auto-warning e-mail.
1.3.6.1.4.1.8691.2.8.1.5.2.3.5DisplayStringread-writecurrent
emailWarningFirstEmailAddr
OBJECT-TYPE
The first email address to where the auto-warning e-mail is to be sent.
1.3.6.1.4.1.8691.2.8.1.5.2.3.6DisplayStringread-writecurrent
emailWarningSecondEmailAddr
OBJECT-TYPE
The second email address to where the auto-warning e-mail is to be sent.
1.3.6.1.4.1.8691.2.8.1.5.2.3.7DisplayStringread-writecurrent
emailWarningThirdEmailAddr
OBJECT-TYPE
The third email address to where the auto-warning e-mail is to be sent.
1.3.6.1.4.1.8691.2.8.1.5.2.3.8DisplayStringread-writecurrent
emailWarningFourthEmailAddr
OBJECT-TYPE
The fourth email address to where the auto-warning e-mail is to be sent.
1.3.6.1.4.1.8691.2.8.1.5.2.3.9DisplayStringread-writecurrent
snmpTrap
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.2.4
snmpTrapReceiverIp
OBJECT-TYPE
SNMP trap receiver IP address or domain name.
1.3.6.1.4.1.8691.2.8.1.5.2.4.1DisplayStringread-writecurrent
trapVersion
OBJECT-TYPE
SNMP trap version used for the auto-warning function.
1.3.6.1.4.1.8691.2.8.1.5.2.4.2INTEGER {v1(0), v2c(1)}read-writecurrent
maintenance
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.3
consoleSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.3.1
httpConsole
OBJECT-TYPE
Enable or disable HTTP console.
1.3.6.1.4.1.8691.2.8.1.5.3.1.1INTEGER {enable(0), disable(1)}read-writecurrent
httpsConsole
OBJECT-TYPE
Enable or disable HTTPS console.
1.3.6.1.4.1.8691.2.8.1.5.3.1.2INTEGER {enable(0), disable(1)}read-writecurrent
telnetConsole
OBJECT-TYPE
Enable or disable Telnet console.
1.3.6.1.4.1.8691.2.8.1.5.3.1.3INTEGER {enable(0), disable(1)}read-writecurrent
sshConsole
OBJECT-TYPE
Enable or disable SSH console.
1.3.6.1.4.1.8691.2.8.1.5.3.1.4INTEGER {enable(0), disable(1)}read-writecurrent
lcmReadOnlyProtect
OBJECT-TYPE
Enable or disable LCM read-only protection. If the LCM panel is under read-only protection, users can only view the configurations from the LCM panel. Otherwise, by default, users can modify the settings directly on the LCM panel.
1.3.6.1.4.1.8691.2.8.1.5.3.1.5INTEGER {writable(0), readonly(1)}read-writecurrent
resetButtonFunction
OBJECT-TYPE
Enable or disable reset button protection. You can disable the hardware reset button after the NPort 6000 series device server has been restarted for 60 seconds.
1.3.6.1.4.1.8691.2.8.1.5.3.1.6INTEGER {always-enable(0), disable-after-60-sec(1)}read-writecurrent
loadFactoryDefault
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.5.3.2
loadFactoryDefaultSetting
OBJECT-TYPE
This function will reset all of the NPort 6000 series device server's settings to the factory default values. Be aware that previous settings will be lost. Selecting Reset to factory default (excluding IP configuration) will reset all settings except the IP configuration to factory defaults. Selecting Reset to factory default will reset all settings including the IP configuration to factory defaults.
1.3.6.1.4.1.8691.2.8.1.5.3.2.1INTEGER {resetToFactoryDefault-ExcludingIpConfiguration(0), resetToFactoryDefault(1)}write-onlycurrent
sysStatus
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.6
s2eConnections
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.6.1
monitorRemoteIpTable
OBJECT-TYPE
Serial to Network Connections Remote IP table.
1.3.6.1.4.1.8691.2.8.1.6.1.1not-accessiblecurrent
monitorRemoteIpEntry
OBJECT-TYPE
Serial to Network Connections Remote IP entry.
1.3.6.1.4.1.8691.2.8.1.6.1.1.1not-accessiblecurrent
remoteIpIndex
OBJECT-TYPE
Serial to Network Connections Remote IP index.
1.3.6.1.4.1.8691.2.8.1.6.1.1.1.1INTEGERread-onlycurrent
monitorRemoteIp
OBJECT-TYPE
The remote IP currently connecting to this port.
1.3.6.1.4.1.8691.2.8.1.6.1.1.1.2IpAddressread-onlycurrent
serialPortStatus
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.6.2
monitorSerialPortStatusTable
OBJECT-TYPE
Serial Port Status table.
1.3.6.1.4.1.8691.2.8.1.6.2.1not-accessiblecurrent
monitorSerialPortStatusEntry
OBJECT-TYPE
Serial Port Status entry.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1not-accessiblecurrent
monitorTxCount
OBJECT-TYPE
View the number of bytes transmitted from the port since the last time the port was initialized.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.1INTEGERread-onlycurrent
monitorRxCount
OBJECT-TYPE
View the number of bytes received by the port since the last time the port was initialized.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.2INTEGERread-onlycurrent
monitorTxTotalCount
OBJECT-TYPE
View the number of bytes transmitted from the port since the last time the system was initialized.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.3INTEGERread-onlycurrent
monitorRxTotalCount
OBJECT-TYPE
View the number of bytes received by the port since the last time the system was initialized.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.4INTEGERread-onlycurrent
monitorDSR
OBJECT-TYPE
View the current DSR status of this port.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.5INTEGER {off(0), on(1)}read-onlycurrent
monitorDTR
OBJECT-TYPE
View the current DTR status of this port.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.6INTEGER {off(0), on(1)}read-onlycurrent
monitorRTS
OBJECT-TYPE
View the current RTS status of this port.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.7INTEGER {off(0), on(1)}read-onlycurrent
monitorCTS
OBJECT-TYPE
View the current CTS status of this port.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.8INTEGER {off(0), on(1)}read-onlycurrent
monitorDCD
OBJECT-TYPE
View the current DCD status of this port.
1.3.6.1.4.1.8691.2.8.1.6.2.1.1.9INTEGER {off(0), on(1)}read-onlycurrent
serialPortErrorCount
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.6.3
monitorSerialPortErrorCountTable
OBJECT-TYPE
Serial Port Error Count table.
1.3.6.1.4.1.8691.2.8.1.6.3.1not-accessiblecurrent
monitorSerialPortErrorCountEntry
OBJECT-TYPE
Serial Port Error Count entry.
1.3.6.1.4.1.8691.2.8.1.6.3.1.1not-accessiblecurrent
monitorErrorCountFrame
OBJECT-TYPE
View the number of 'Frame' errors for this port.
1.3.6.1.4.1.8691.2.8.1.6.3.1.1.1INTEGERread-onlycurrent
monitorErrorCountParity
OBJECT-TYPE
View the number of 'Parity' errors for this port.
1.3.6.1.4.1.8691.2.8.1.6.3.1.1.2INTEGERread-onlycurrent
monitorErrorCountOverrun
OBJECT-TYPE
View the number of 'Overrun' errors for this port.
1.3.6.1.4.1.8691.2.8.1.6.3.1.1.3INTEGERread-onlycurrent
monitorErrorCountBreak
OBJECT-TYPE
View the number of 'Break' errors for this port.
1.3.6.1.4.1.8691.2.8.1.6.3.1.1.4INTEGERread-onlycurrent
serialPortSettings
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.6.4
monitorSerialPortSettingsTable
OBJECT-TYPE
Serial Port Settings table.
1.3.6.1.4.1.8691.2.8.1.6.4.1not-accessiblecurrent
monitorSerialPortSettingsEntry
OBJECT-TYPE
Serial Port Settings entry.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1not-accessiblecurrent
monitorBaudRate
OBJECT-TYPE
View the current baudrate of the port.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.1INTEGERread-onlycurrent
monitorDataBits
OBJECT-TYPE
View the number of bits per byte for the port.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.2INTEGERread-onlycurrent
monitorStopBits
OBJECT-TYPE
View the number of stop bits for the port.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.3DisplayStringread-onlycurrent
monitorParity
OBJECT-TYPE
View the parity bit for the port.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.4INTEGER {none(0), odd(8), even(24), mark(40), space(56)}read-onlycurrent
monitorRTSCTSFlowControl
OBJECT-TYPE
View if the port is using RTS/CTS flow control.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.5INTEGER {off(0), on(1)}read-onlycurrent
monitorXONXOFFFlowControl
OBJECT-TYPE
View if the port is using XON/XOFF flow control.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.6INTEGER {off(0), on(1)}read-onlycurrent
monitorDTRDSRFlowControl
OBJECT-TYPE
View if the port is using DTR/DSR flow control.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.7INTEGER {off(0), on(1)}read-onlycurrent
monitorFIFO
OBJECT-TYPE
View FIFO status of this port.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.8INTEGER {disable(0), enable(1)}read-onlycurrent
monitorInterface
OBJECT-TYPE
View the serial interface that the port is using.
1.3.6.1.4.1.8691.2.8.1.6.4.1.1.9INTEGER {rs-232(0), rs-422(1), rs-485-2-wire(2), rs-485-4-wire(3)}read-onlycurrent
relayOutputStatus
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.6.5
relayOutputEthernet1LinkDown
OBJECT-TYPE
The relay dout status of the event that the built- in LAN port is off.
1.3.6.1.4.1.8691.2.8.1.6.5.1INTEGER {none(0), alarm(1), alarm-Acked(2)}read-onlycurrent
ethernet1LinkDownAcknowledge
OBJECT-TYPE
Acknowledge the event that the built-in LAN port is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem.
1.3.6.1.4.1.8691.2.8.1.6.5.2INTEGER {acked(0)}write-onlycurrent
relayOutputEthernet2LinkDown
OBJECT-TYPE
The relay dout status of the event that the first LAN port of the network module is off.
1.3.6.1.4.1.8691.2.8.1.6.5.3INTEGER {none(0), alarm(1), alarm-Acked(2)}read-onlycurrent
ethernet2LinkDownAcknowledge
OBJECT-TYPE
Acknowledge the event that the first LAN port of the network module is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem.
1.3.6.1.4.1.8691.2.8.1.6.5.4INTEGER {acked(0)}write-onlycurrent
relayOutputEthernet3LinkDown
OBJECT-TYPE
The relay dout status of the event that the second LAN port of the network module is off.
1.3.6.1.4.1.8691.2.8.1.6.5.5INTEGER {none(0), alarm(1), alarm-Acked(2)}read-onlycurrent
ethernet3LinkDownAcknowledge
OBJECT-TYPE
Acknowledge the event that the second LAN port of the network module is off. Acknowledgement will clear the d-out alarm before you can actually fix the problem.
1.3.6.1.4.1.8691.2.8.1.6.5.6INTEGER {acked(0)}write-onlycurrent
portDCDChangedStatusTable
OBJECT-TYPE
DCD changed table.
1.3.6.1.4.1.8691.2.8.1.6.5.7not-accessiblecurrent
portDCDChangedStatusEntry
OBJECT-TYPE
DCD changed entry.
1.3.6.1.4.1.8691.2.8.1.6.5.7.1not-accessiblecurrent
portDCDChangedStatus
OBJECT-TYPE
The relay dout status of the event that the DCD signal of the port is changed.
1.3.6.1.4.1.8691.2.8.1.6.5.7.1.1INTEGER {none(0), alarm(1), alarm-Acked(2)}read-onlycurrent
portDCDChangedAcknowledge
OBJECT-TYPE
Acknowledge the event that the DCD signal of the port is changed. Acknowledgement will clear the d-out alarm before you can actually fix the problem.
1.3.6.1.4.1.8691.2.8.1.6.5.7.1.2INTEGER {acked(0)}write-onlycurrent
portDSRChangedStatusTable
OBJECT-TYPE
DSR changed Table.
1.3.6.1.4.1.8691.2.8.1.6.5.8not-accessiblecurrent
portDSRChangedStatusEntry
OBJECT-TYPE
DSR changed entry.
1.3.6.1.4.1.8691.2.8.1.6.5.8.1not-accessiblecurrent
portDSRChangedStatus
OBJECT-TYPE
The relay dout status of the event that the DSR signal of the port is changed.
1.3.6.1.4.1.8691.2.8.1.6.5.8.1.1INTEGER {none(0), alarm(1), alarm-Acked(2)}read-onlycurrent
portDSRChangedAcknowledge
OBJECT-TYPE
Acknowledge the event that the DSR signal of the port is changed. Acknowledgement will clear the d-out alarm before you can actually fix the problem.
1.3.6.1.4.1.8691.2.8.1.6.5.8.1.2INTEGER {acked(0)}write-onlycurrent
saveConfiguration
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.7
saveConfig
OBJECT-TYPE
Save the applied configuration to the NPort 6000 series device server.
1.3.6.1.4.1.8691.2.8.1.7.1INTEGER {save(1)}write-onlycurrent
restart
OBJECT-IDENTITY
1.3.6.1.4.1.8691.2.8.1.8
restartPorts
OBJECT-TYPE
Restart serial port. Restarting will cause port reseting.
1.3.6.1.4.1.8691.2.8.1.8.1INTEGER {port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15)}write-onlycurrent
restartSystem
OBJECT-TYPE
Restart the NPort 6000 series device server. Be sure to save all of your configuration changes before you restart the system. Otherwise, all of the changes will be lost.
1.3.6.1.4.1.8691.2.8.1.8.2INTEGER {restart(1)}write-onlycurrent