MITEL-LOGICAL-MIB
- Registered at
- 1.3.6.1.4.1.1027.4.8.1.4
- Last updated
- 2003-03-24 09:47
- Organization
- MITEL Corporation
- Revisions
- 2003-03-24 09:47, 1999-03-01 00:00
- Namespace
- mitel
- Source file
MITEL-LOGICAL-MIB- Digest
sha256:b4f98acbec181d41bc4eac56ba20783a08ed8330b297234e73c51bad173f928e
Description
The MITEL Logical MIB module.
Contact
Standards Group, Postal: MITEL Corporation 350 Legget Drive, PO Box 13089 Kanata, Ontario Canada K2K 1X3 Tel: +1 613 592 2122 Fax: +1 613 592 4784 E-mail: std@mitel.com
Imports
| From | Symbols |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso |
| SNMPv2-TC | DisplayString, RowStatus, TEXTUAL-CONVENTION |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
MITEL-LOGICAL-MIB SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| mitel OBJECT-IDENTITY | 1.3.6.1.4.1.1027 | |||
| mitelIdentification OBJECT-IDENTITY | 1.3.6.1.4.1.1027.1 | |||
| mitelIdCallServers OBJECT-IDENTITY | 1.3.6.1.4.1.1027.1.2 | |||
| mitelIdCsIpera1000 OBJECT-IDENTITY | 1.3.6.1.4.1.1027.1.2.4 | |||
| mitelProprietary OBJECT-IDENTITY | 1.3.6.1.4.1.1027.4 | |||
| mitelPropIpNetworking OBJECT-IDENTITY | 1.3.6.1.4.1.1027.4.8 | |||
| mitelIpNetRouter OBJECT-IDENTITY | 1.3.6.1.4.1.1027.4.8.1 | |||
| mitelLogGrpLogicalTable OBJECT-TYPE A table containing information about logical LAN destinations. | 1.3.6.1.4.1.1027.4.8.1.4.1 | not-accessible | current | |
| mitelLogGrpLogicalEntry OBJECT-TYPE Each entry of this table contains information about a specific logical interface to a local area network. Each logical LAN can support routing functions, these are considered virtual interfaces. The logical LAN can be permanently attached to a physical port (LAN or WAN) or it can float among available physical resources (WAN's only). | 1.3.6.1.4.1.1027.4.8.1.4.1.1 | not-accessible | current | |
| mitelLogicalTblIndex OBJECT-TYPE This object identifies the instance of this entry in the table. | 1.3.6.1.4.1.1027.4.8.1.4.1.1.1 | Integer32 | read-only | current |
| mitelLogicalTblDestName OBJECT-TYPE The Ascii string associated with this logical destination LAN. Default is Net N (N is mitelLogicalTblIndex). | 1.3.6.1.4.1.1027.4.8.1.4.1.1.2 | DisplayString (SIZE(1..16)) | read-write | current |
| mitelLogicalTblType OBJECT-TYPE This object determines whether this network interface is locally connected to a LAN or is connected to a LAN via a WAN. If this object is set to local(1) then this interface is associated with one of the physical LAN interfaces via the ifIndex. If this object indicates remote(2) then this network is reachable through a wide area network (WAN) as described in mitelLogGrpLogicalWanTable. | 1.3.6.1.4.1.1027.4.8.1.4.1.1.3 | INTEGER {local(1), remote(2)} | read-only | current |
| mitelLogicalTblAdminStatus OBJECT-TYPE The current desired state of this sub-layer. Default is down. | 1.3.6.1.4.1.1027.4.8.1.4.1.1.4 | INTEGER {up(1), down(2)} | read-write | current |
| mitelLogGrpLogicalWanTable OBJECT-TYPE A table containing configuration parameters for wide area network connections to logical LAN destinations that are accessible via interfaces. Each entry is logically tied to a logical LAN destination entry via mitelLogicalTblIndex. | 1.3.6.1.4.1.1027.4.8.1.4.2 | not-accessible | current | |
| mitelLogGrpLogicalWanEntry OBJECT-TYPE Each entry of this table contains information about a specific logical interface to a REMOTELY connected local area network. The instance of mitelLogicalTblIndex used to index into this table is the same instance value used to index into the grLogicalTable. | 1.3.6.1.4.1.1027.4.8.1.4.2.1 | not-accessible | current | |
| mitelLogWanTblCmprsn OBJECT-TYPE This object indicates whether or not this interface is to perform data compression. Default is none. | 1.3.6.1.4.1.1027.4.8.1.4.2.1.1 | INTEGER {none(1), any(2), gandalf(3), stac(4)} | read-write | current |
| mitelLogWanTblCmprsnStatus OBJECT-TYPE This object describes the type of compression used on this destination. | 1.3.6.1.4.1.1027.4.8.1.4.2.1.2 | INTEGER {none(1), fza(2), fzap(3), concryption(4), encryption(5), stacNoCheckMode(6), stacLCBCheckMode(7), stacCRCCheckMode(8), stacSeqNumbers(9), stacExtendedMode(10), stacAscendLCBMode(11)} | read-only | current |
| mitelLogWanTblEncryptn OBJECT-TYPE This object describes whether or not PPP encryption is proposed to the peer. Default is disabled. | 1.3.6.1.4.1.1027.4.8.1.4.2.1.3 | INTEGER {enabled(1), disabled(2)} | read-write | current |
| mitelLogWanTblBackupOvrflow OBJECT-TYPE This object determines if this interface is to attempt to bring up another link to the same destination if the traffic over the primary link exceeds a pre-determined threshold, in the case of overflow(3). Otherwise, if backup(2) is selected the interface will bring up an alternate link to the same destination in the case that the primary link fails. Default is disabled(1). | 1.3.6.1.4.1.1027.4.8.1.4.2.1.4 | INTEGER {disabled(1), backup(2), overflow(3)} | read-write | current |
| mitelLogWanTblThshld OBJECT-TYPE This object determines the transmit threshold which when exceeded will cause an attempt to bring up another path. The returned value of this object has no meaning when threshold overflow is not enabled. Default is 80. | 1.3.6.1.4.1.1027.4.8.1.4.2.1.5 | INTEGER (0..100) | read-write | current |
| mitelLogWanTblConnTimer OBJECT-TYPE When threshold overflow is enabled this object determines the amount of time in seconds that the average threshold must be exceeded (or below) before another link is established (or disconnected). Default is 30. | 1.3.6.1.4.1.1027.4.8.1.4.2.1.6 | INTEGER (1..3600) | read-write | current |
| mitelLogWanTblDiscTimer OBJECT-TYPE The time a non-permanent link will remain connected without traffic. Default is 30. | 1.3.6.1.4.1.1027.4.8.1.4.2.1.7 | INTEGER (0..3600) | read-write | current |
| mitelLogWanTblProtocolType OBJECT-TYPE The protocol type that this destination is over. Default is ppp. | 1.3.6.1.4.1.1027.4.8.1.4.2.1.8 | INTEGER {ppp(1), framerelay(2), x25(3)} | read-write | current |
| mitelLogGrpLogicalWanPortTable OBJECT-TYPE This configuration table identifies the characteristics of each potential transportation pipe to a remote site. Each entry in this table is associated with an entry in the grLogWanTable via its mitelLogicalTblIndex. Multiple entries can be associated with a single entry in the mitelLogGrpLogicalWanTable. | 1.3.6.1.4.1.1027.4.8.1.4.3 | not-accessible | current | |
| mitelLogGrpLogicalWanPortEntry OBJECT-TYPE Each entry of this table contains information about a single WAN resource used by a logical interface to a remote local area network. The instance of mitelLogicalTblIndex used to index into this table is the same instance value used to index into the mitelLogicalTable. Multiple entries in this table having the same mitelLogicalTblIndex usually indicates backup or multi-linking functionality. | 1.3.6.1.4.1.1027.4.8.1.4.3.1 | not-accessible | current | |
| mitelLogWanPortTblIndex OBJECT-TYPE Identifies the port index associated with this entry. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.1 | Integer32 | read-only | current |
| mitelLogWanPortTblWanType OBJECT-TYPE Indicates whether or not this link is to be used as a permanent or ondemand link. Default is ondemand | 1.3.6.1.4.1.1027.4.8.1.4.3.1.2 | INTEGER {permanent(1), ondemand(2), incomming(3), outgoing(4)} | read-write | current |
| mitelLogWanPortTblTransType OBJECT-TYPE The transport type that this destination is over. Default is HDLC. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.3 | INTEGER {hdlc(1), modem(2), ethernet(3)} | read-write | current |
| mitelLogWanPortTblRetry OBJECT-TYPE Determines the retry count for dial up WAN circuits. Default is 10. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.4 | INTEGER (0..99) | read-write | current |
| mitelLogWanPortTblRetryPeriod OBJECT-TYPE Determines the retry period in seconds for dial up WAN circuits. Default is 10 seconds. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.5 | INTEGER (0..99) | read-write | current |
| mitelLogWanPortTblPrepend OBJECT-TYPE Indicates in most cases an Ascii string that will be prepended to the destination address. Default is NULL. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.6 | OCTET STRING (SIZE(3)) | read-write | current |
| mitelLogWanPortTblDestAddr OBJECT-TYPE Indicates the destination address that this interface will call (ie: phone number). Default is NULL. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.7 | DisplayString (SIZE(1..20)) | read-write | current |
| mitelLogWanPortTblNextDestAddr OBJECT-TYPE Indicates the next destination address that this interface will call (ie: phone number). Default is NULL. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.8 | DisplayString (SIZE(1..20)) | read-write | current |
| mitelLogWanPortTblChId OBJECT-TYPE This object is a unique identifier for this network channel. e.g. DLCI for frame-relay. The value must be within the defined range or if not used the DEFAULT value should be 0. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.9 | INTEGER (0..65535) | read-write | current |
| mitelLogWanPortTblDialback OBJECT-TYPE Enables/disables dialback option. If enabled the system will drop the link and then dial the user back using the configured dial string or a dial string reported from an authentication server. Default is disabled. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.10 | INTEGER {enable(1), disable(2)} | read-write | current |
| mitelLogWanPortTblAdminStatus OBJECT-TYPE The current desired state of this sub-layer. Default is down. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.11 | INTEGER {up(1), down(2)} | read-write | current |
| mitelLogWanPortTblOperStatus OBJECT-TYPE The current active state of this sub-layer. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.12 | INTEGER {connecting(1), connected(2), disconnecting(3), disconnected(4), retryExhausted(5)} | read-only | current |
| mitelLogWanPortTblStatus OBJECT-TYPE The current status of this entry. | 1.3.6.1.4.1.1027.4.8.1.4.3.1.13 | RowStatus | read-create | current |
Notifications
| Name | OID | Status |
|---|---|---|
| mitelWanRetryThreshold NOTIFICATION-TYPE The mitelWanRetryThreshold trap is generated by the router whenever the maximum number of retries have been exhausted when attempting to contact a remote site on a specific serial interface. The mitelLogicalTblIndex will provided in the variable bindings for this trap type. | 1.3.6.1.4.1.1027.1.2.4.0.403 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| mitelIpera1000Notifications NOTIFICATION-GROUP Notifications for Call Server IPera 1000. | 1.3.6.1.4.1.1027.1.2.4.0 | current |