L2TP-MIB
- Registered at
- 1.3.6.1.2.1.10.95
- Last updated
- 2002-08-23 00:00
- Organization
- IETF L2TP Working Group
- Revisions
- 2002-08-23 00:00
- Namespace
- standard
- Source file
L2TP-MIB- Digest
sha256:69e0b0d674b6d8f04573e62aaff8b01b721291ec4a646cae4b393f13983bd955
Description
The MIB module that describes managed objects of general use by the Layer Two Transport Protocol.
Contact
Evan Caves Postal: Occam Networks 77 Robin Hill Road Santa Barbara, CA, 93117 Tel: +1 805692 2900 Email: evan@occamnetworks.com Pat R. Calhoun Postal: Black Storm Networks 110 Nortech Parkway San Jose, CA, 95143 Tel: +1 408 941-0500 Email: pcalhoun@bstormnetworks.com Ross Wheeler Postal: DoubleWide Software, Inc. 2953 Bunker Hill Lane Suite 101 Santa Clara, CA 95054 Tel: +1 6509260599 Email: ross@doublewidesoft.com Layer Two Tunneling Protocol Extensions WG Working Group Area: Internet Working Group Name: l2tpext General Discussion: l2tp@l2tp.net
Imports
| From | Symbols |
|---|---|
| IF-MIB | InterfaceIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Counter64, Gauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso, transmission |
| SNMPv2-TC | DisplayString, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
IANAifType-MIB IF-MIB L2TP-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| L2tpMilliSeconds TEXTUAL-CONVENTION A period of time measured in units of .001 of seconds when used in conjunction with the DISPLAY-HINT will show seconds and fractions of second with a resolution of .001 of a second. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| l2tpNotifications OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.0 | |||
| l2tpObjects OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.1 | |||
| l2tpScalar OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.1.1 | |||
| l2tpConfig OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.1.1.1 | |||
| l2tpAdminState OBJECT-TYPE This object defines the administrative state of the L2TP protocol. Setting this object to 'disabled' causes all tunnels to be immediately disconnected and no further tunnels to be either initiated or accepted. The value of this object must be maintained in non-volatile memory. | 1.3.6.1.2.1.10.95.1.1.1.1 | INTEGER {enabled(1), disabled(2)} | read-write | current |
| l2tpDrainTunnels OBJECT-TYPE Setting this object to 'true' will prevent any new tunnels and/or sessions to be either initiated or accepted but does NOT disconnect any active tunnels/sessions. Setting this object to true(1) causes all domains and their respective tunnels to transition to the draining state. Note that when this occurs the 'xxxDraining' status objects of the domains and their tunnels should reflect that they are 'draining'. Setting this object has no affect on the domains or their tunnels 'xxxDrainTunnels' configuration objects. To cancel a drain this object should be set to false(2). The object l2tpDrainingTunnels reflects the current L2TP draining state. The value of this object must be maintained in non-volatile memory. | 1.3.6.1.2.1.10.95.1.1.1.2 | TruthValue | read-write | current |
| l2tpStats OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.1.1.2 | |||
| l2tpProtocolVersions OBJECT-TYPE Vector of supported L2TP protocol version and revision numbers. Supported versions are identified via a two octet pairing where the first octet indicates the version and the second octet contains the revision. | 1.3.6.1.2.1.10.95.1.1.2.1 | OCTET STRING (SIZE(2..256)) | read-only | current |
| l2tpVendorName OBJECT-TYPE This object identifies the Vendor name of the L2TP protocol stack. | 1.3.6.1.2.1.10.95.1.1.2.2 | SnmpAdminString | read-only | current |
| l2tpFirmwareRev OBJECT-TYPE This object defines the firmware revision for the L2TP protocol stack. | 1.3.6.1.2.1.10.95.1.1.2.3 | Integer32 | read-only | current |
| l2tpDrainingTunnels OBJECT-TYPE This object indicates if the local L2TP is draining off sessions from all tunnels. | 1.3.6.1.2.1.10.95.1.1.2.4 | TruthValue | read-only | current |
| l2tpDomainConfigTable OBJECT-TYPE The L2TP Domain configuration table. This table contains objects that can be used to configure the operational characteristics of a tunnel domain. There is a 1-1 correspondence between conceptual rows of this table and conceptual rows of the l2tpDomainStatsTable. | 1.3.6.1.2.1.10.95.1.2 | not-accessible | current | |
| l2tpDomainConfigEntry OBJECT-TYPE An L2TP Domain configuration entry. An entry in this table may correspond to a single endpoint or a group of tunnel endpoints. | 1.3.6.1.2.1.10.95.1.2.1 | not-accessible | current | |
| l2tpDomainConfigId OBJECT-TYPE The identifier, usually in the form of a Domain Name (full or partial), describing a single tunnel endpoint or a domain of tunnel endpoints. This is typically used as a 'handle' to identify the tunnel configuration requirements for both incoming and outgoing tunnel connection attempts. Both the LAC and LNS could use information provided in the Host Name AVP attribute however the tunnel initiator could use other means not specified to identify the domain's tunnel configuration requirements. For example; three rows in this table have l2tpDomainConfigId values of 'lac1.isp.com', 'isp.com' and 'com'. A tunnel endpoint then identifies itself as 'lac1.isp.com' which would match the 'lac1.isp.com' entry in this table. A second tunnel endpoint then identifies itself as 'lac2.isp.com'. This endpoint is then associated with the 'isp.com' entry of this table. | 1.3.6.1.2.1.10.95.1.2.1.1 | SnmpAdminString (SIZE(1..80)) | not-accessible | current |
| l2tpDomainConfigAdminState OBJECT-TYPE This object defines the administrative state of this tunnel domain. Setting this object to disabled(2) causes all tunnels to be immediately disconnected and no further tunnels to be either initiated or accepted. Note that all columnar objects corresponding to this conceptual row cannot be modified when the administrative state is enabled EXCEPT those objects which specifically state otherwise. | 1.3.6.1.2.1.10.95.1.2.1.2 | INTEGER {enabled(1), disabled(2)} | read-create | current |
| l2tpDomainConfigDrainTunnels OBJECT-TYPE Setting this object to 'true' will prevent any new tunnels and/or sessions from being either initiated or accepted but does NOT disconnect any active tunnels/sessions for this tunnel domain. Setting this object to true(1) causes all tunnels within this domain to transition to the draining state. Note that when this occurs the l2tpTunnelStatsDrainingTunnel status objects of all of this domain's tunnels should reflect that they are 'draining'. Setting this object has no effect on this domain's associated tunnels l2tpTunnelConfigDrainTunnel configuration objects. To cancel a drain this object should be set to false(2). Setting this object to false(2) when the L2TP object l2tpDrainTunnels is true(1) has no affect, all domains and their tunnels will continue to drain. | 1.3.6.1.2.1.10.95.1.2.1.3 | TruthValue | read-create | current |
| l2tpDomainConfigAuth OBJECT-TYPE This object describes how tunnel peers belonging to this domain are to be authenticated. The value simple(2) indicates that peers are authenticated simply by their host name as described in the Host Name AVP. The value challenge(3) indicates that all peers are challenged to prove their identification. This mechanism is described in the L2TP protocol. | 1.3.6.1.2.1.10.95.1.2.1.4 | INTEGER {none(1), simple(2), challenge(3)} | read-create | current |
| l2tpDomainConfigSecret OBJECT-TYPE This object is used to configure the shared secret used during the tunnel authentication phase of tunnel establishment. This object MUST be accessible only via requests using both authentication and privacy. The agent MUST report an empty string in response to get, get-next and get-bulk requests. | 1.3.6.1.2.1.10.95.1.2.1.5 | SnmpAdminString (SIZE(0..255)) | read-create | current |
| l2tpDomainConfigTunnelSecurity OBJECT-TYPE This object defines whether this tunnel domain requires that all tunnels are to be secured. The value of ipsec(3) indicates that all tunnel packets, control and session, have IP Security headers. The type of IP Security headers (AH, ESP etc) and how they are further described is outside the scope of this document. | 1.3.6.1.2.1.10.95.1.2.1.6 | INTEGER {none(1), other(2), ipSec(3)} | read-create | current |
| l2tpDomainConfigTunnelHelloInt OBJECT-TYPE This object defines the interval in which Hello (or keep-alive) packets are to be sent by local peers belonging to this tunnel domain. The value zero effectively disables the sending of Hello packets. This object may be modified when the administrative state is enabled for this conceptual row. | 1.3.6.1.2.1.10.95.1.2.1.7 | Integer32 (0..3600) | read-create | current |
| l2tpDomainConfigTunnelIdleTO OBJECT-TYPE This object defines the period of time that an established tunnel belonging to this tunnel domain with no active sessions will wait before disconnecting the tunnel. A value of zero indicates that the tunnel will disconnect immediately after the last session disconnects. A value of -1 leaves the tunnel up indefinitely. This object may be modified when the administrative state is enabled for this conceptual row. | 1.3.6.1.2.1.10.95.1.2.1.8 | Integer32 (-1..86400) | read-create | current |
| l2tpDomainConfigControlRWS OBJECT-TYPE This object defines the control channel receive window size for tunnels belonging to this domain. It specifies the maximum number of packets the tunnel peer belonging to this domain can send without waiting for an acknowledgement from this peer. | 1.3.6.1.2.1.10.95.1.2.1.9 | Integer32 (1..65535) | read-create | current |
| l2tpDomainConfigControlMaxRetx OBJECT-TYPE This object defines the maximum number of retransmissions which the L2TP stack will attempt for tunnels belonging to this domain before assuming that the peer is no longer responding. | 1.3.6.1.2.1.10.95.1.2.1.10 | Integer32 (0..32) | read-create | current |
| l2tpDomainConfigControlMaxRetxTO OBJECT-TYPE This object defines the maximum retransmission timeout interval which the L2TP stack will wait for tunnels belonging to this domain before retransmitting a control packet that has not been acknowledged. | 1.3.6.1.2.1.10.95.1.2.1.11 | Integer32 (1..32) | read-create | current |
| l2tpDomainConfigPayloadSeq OBJECT-TYPE This object determines whether or not session payload packets will be requested to be sent with sequence numbers from tunnel peers belonging to this domain. The value onDemand(1) allows the L2TP implementation to initiate payload sequencing when necessary based on local information (e.g: during LCP/NCP negotiations or for CCP). The value never(2) indicates that L2TP will never initiate sequencing but will do sequencing if asked. The value always(3) indicates that L2TP will send the Sequencing Required AVP during session establishment. | 1.3.6.1.2.1.10.95.1.2.1.12 | INTEGER {onDemand(1), never(2), always(3)} | read-create | current |
| l2tpDomainConfigReassemblyTO OBJECT-TYPE This object defines the number of milliseconds that local peers of this tunnel domain will wait before processing payload packets that were received out of sequence (which are waiting for the packet(s) to put them in sequence). A low value increases the chance of delayed packets to be discarded (which MAY cause the PPP decompression engine to reset) while a high value may cause more queuing and possibly degrade throughput if packets are truly lost. The default value for this object is zero which will result in all delayed packets being lost. | 1.3.6.1.2.1.10.95.1.2.1.13 | L2tpMilliSeconds | read-create | current |
| l2tpDomainConfigProxyPPPAuth OBJECT-TYPE This object is used to configure the sending or acceptance of the PPP Proxy Authentication AVP's on the LAC or LNS. | 1.3.6.1.2.1.10.95.1.2.1.14 | TruthValue | read-create | current |
| l2tpDomainConfigStorageType OBJECT-TYPE The storage type for this conceptual row. Conceptual rows having the value 'permanent' must allow write-access at a minimum to: - l2tpDomainConfigAdminState and l2tpDomainConfigDrainTunnels at all times - l2tpDomainConfigSecret if l2tpDomainConfigAuth has been configured as 'challenge' It is an implementation issue to decide if a SET for a readOnly or permanent row is accepted at all. In some contexts this may make sense, in others it may not. If a SET for a readOnly or permanent row is not accepted at all, then a 'wrongValue' error must be returned. | 1.3.6.1.2.1.10.95.1.2.1.15 | StorageType | read-create | current |
| l2tpDomainConfigStatus OBJECT-TYPE The status of this Domain entry. Columnar objects corresponding to this conceptual row may be modified according to their description clauses when this RowStatus object is 'active'. | 1.3.6.1.2.1.10.95.1.2.1.16 | RowStatus | read-create | current |
| l2tpDomainStatsTable OBJECT-TYPE The L2TP Domain Status and Statistics table. This table contains objects that can be used to describe the current status and statistics of a tunnel domain. There is a 1-1 correspondence between conceptual rows of this table and conceptual rows of the l2tpDomainConfigTable. | 1.3.6.1.2.1.10.95.1.3 | not-accessible | current | |
| l2tpDomainStatsEntry OBJECT-TYPE An L2TP Domain Stats entry. An entry in this table may correspond to a single endpoint or a group of tunnel endpoints. | 1.3.6.1.2.1.10.95.1.3.1 | not-accessible | current | |
| l2tpDomainStatsTotalTunnels OBJECT-TYPE This object returns the total number of tunnels that have successfully reached the established state for this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.1 | Counter32 | read-only | current |
| l2tpDomainStatsFailedTunnels OBJECT-TYPE This object returns the number of tunnels that failed (eg: connection timeout, unsupported or malformed AVP's etc) to reach the established state for this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.2 | Counter32 | read-only | current |
| l2tpDomainStatsFailedAuths OBJECT-TYPE This object returns the number of failed tunnel connection attempts for this domain because the tunnel peer failed authentication. | 1.3.6.1.2.1.10.95.1.3.1.3 | Counter32 | read-only | current |
| l2tpDomainStatsActiveTunnels OBJECT-TYPE This object returns the number of tunnels that are currently active for this domain. | 1.3.6.1.2.1.10.95.1.3.1.4 | Gauge32 | read-only | current |
| l2tpDomainStatsTotalSessions OBJECT-TYPE This object returns the total number of sessions that have successfully reached the established state for this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.5 | Counter32 | read-only | current |
| l2tpDomainStatsFailedSessions OBJECT-TYPE This object returns the number of sessions that failed (eg: connection timeout, unsupported or malformed AVP's etc) to reach the established state for this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.6 | Counter32 | read-only | current |
| l2tpDomainStatsActiveSessions OBJECT-TYPE This object returns the number of sessions that are currently active for this domain. | 1.3.6.1.2.1.10.95.1.3.1.7 | Gauge32 | read-only | current |
| l2tpDomainStatsDrainingTunnels OBJECT-TYPE This object indicates if this domain is draining off sessions from all tunnels. | 1.3.6.1.2.1.10.95.1.3.1.8 | TruthValue | read-only | current |
| l2tpDomainStatsControlRxOctets OBJECT-TYPE This object returns the number of control channel octets received for this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.9 | Counter32 | read-only | current |
| l2tpDomainStatsControlRxPkts OBJECT-TYPE This object returns the number of control packets received for this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.10 | Counter32 | read-only | current |
| l2tpDomainStatsControlTxOctets OBJECT-TYPE This object returns the number of control channel octets that were transmitted to tunnel endpoints for this domain. | 1.3.6.1.2.1.10.95.1.3.1.11 | Counter32 | read-only | current |
| l2tpDomainStatsControlTxPkts OBJECT-TYPE This object returns the number of control packets that were transmitted to tunnel endpoints for this domain. | 1.3.6.1.2.1.10.95.1.3.1.12 | Counter32 | read-only | current |
| l2tpDomainStatsPayloadRxOctets OBJECT-TYPE This object returns the number of payload channel octets that were received for this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.13 | Counter32 | read-only | current |
| l2tpDomainStatsPayloadRxPkts OBJECT-TYPE This object returns the number of payload packets that were received for this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.14 | Counter32 | read-only | current |
| l2tpDomainStatsPayloadRxDiscs OBJECT-TYPE This object returns the number of received payload packets that were discarded by this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.15 | Counter32 | read-only | current |
| l2tpDomainStatsPayloadTxOctets OBJECT-TYPE This object returns the number of payload channel octets that were transmitted to tunnel peers within this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.16 | Counter32 | read-only | current |
| l2tpDomainStatsPayloadTxPkts OBJECT-TYPE This object returns the number of payload packets that were transmitted to tunnel peers within this tunnel domain. | 1.3.6.1.2.1.10.95.1.3.1.17 | Counter32 | read-only | current |
| l2tpDomainStatsControlHCRxOctets OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsControlRxOctets. | 1.3.6.1.2.1.10.95.1.3.1.18 | Counter64 | read-only | current |
| l2tpDomainStatsControlHCRxPkts OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsControlRxPkts. | 1.3.6.1.2.1.10.95.1.3.1.19 | Counter64 | read-only | current |
| l2tpDomainStatsControlHCTxOctets OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsControlTxOctets. | 1.3.6.1.2.1.10.95.1.3.1.20 | Counter64 | read-only | current |
| l2tpDomainStatsControlHCTxPkts OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsControlTxPkts. | 1.3.6.1.2.1.10.95.1.3.1.21 | Counter64 | read-only | current |
| l2tpDomainStatsPayloadHCRxOctets OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsPayloadRxOctets. | 1.3.6.1.2.1.10.95.1.3.1.22 | Counter64 | read-only | current |
| l2tpDomainStatsPayloadHCRxPkts OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsPayloadRxPkts. | 1.3.6.1.2.1.10.95.1.3.1.23 | Counter64 | read-only | current |
| l2tpDomainStatsPayloadHCRxDiscs OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsPayloadRxDiscs. | 1.3.6.1.2.1.10.95.1.3.1.24 | Counter64 | read-only | current |
| l2tpDomainStatsPayloadHCTxOctets OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsPayloadTxOctets. | 1.3.6.1.2.1.10.95.1.3.1.25 | Counter64 | read-only | current |
| l2tpDomainStatsPayloadHCTxPkts OBJECT-TYPE This object is a 64-bit version of l2tpDomainStatsPayloadTxPkts. | 1.3.6.1.2.1.10.95.1.3.1.26 | Counter64 | read-only | current |
| l2tpTunnelConfigTable OBJECT-TYPE The L2TP tunnel configuration table. This table contains objects that can be used to (re)configure the operational characteristics of a single L2TP tunnel. There is a 1-1 correspondence between conceptual rows of this table and conceptual rows of the l2tpTunnelStatsTable. Entries in this table have the same persistency characteristics as that of the tunnelConfigTable. | 1.3.6.1.2.1.10.95.1.4 | not-accessible | current | |
| l2tpTunnelConfigEntry OBJECT-TYPE A L2TP tunnel interface configuration entry. Entries in this table come and go as a result of protocol interactions or on management operations. The latter occurs when a row is instantiated in the tunnelConfigTable row and the encapsulation method is 'l2tp'. | 1.3.6.1.2.1.10.95.1.4.1 | not-accessible | current | |
| l2tpTunnelConfigIfIndex OBJECT-TYPE This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type L2TP. | 1.3.6.1.2.1.10.95.1.4.1.1 | InterfaceIndex | not-accessible | current |
| l2tpTunnelConfigDomainId OBJECT-TYPE The tunnel domain that this tunnel belongs to. A LNS tunnel endpoint will typically inherit this value from the endpoint domain table. A LAC may be provided with this information during tunnel setup. When a zero length string is returned this tunnel does not belong belong to any particular domain. | 1.3.6.1.2.1.10.95.1.4.1.2 | SnmpAdminString (SIZE(1..80)) | read-write | current |
| l2tpTunnelConfigAuth OBJECT-TYPE This object describes how L2TP tunnel peers are to be authenticated. The value 'simple' indicates that peers are authenticated simply by their host name as described in the Host Name AVP. The value 'challenge' indicates that all peers are challenged to prove their identification. This mechanism is described in the L2TP protocol. This object cannot be modified when the tunnel is in a connecting or connected state. | 1.3.6.1.2.1.10.95.1.4.1.3 | INTEGER {none(1), simple(2), challenge(3)} | read-write | current |
| l2tpTunnelConfigSecret OBJECT-TYPE This object is used to configure the shared secret used during the tunnel authentication phase of tunnel establishment. This object cannot be modified when the tunnel is in a connecting or connected state. This object MUST be accessible only via requests using both authentication and privacy. The agent MUST report an empty string in response to get, get-next and get-bulk requests. | 1.3.6.1.2.1.10.95.1.4.1.4 | SnmpAdminString (SIZE(0..255)) | read-write | current |
| l2tpTunnelConfigSecurity OBJECT-TYPE This object defines whether this tunnel is to be secured. The value of 'ipSec' indicates that all tunnel packets, control and session, have IP Security headers. The type of IP Security headers (AH, ESP etc) and how they are further described is outside the scope of this document. This object cannot be modified when the tunnel is in a connecting or connected state. | 1.3.6.1.2.1.10.95.1.4.1.5 | INTEGER {none(1), other(2), ipsec(3)} | read-write | current |
| l2tpTunnelConfigHelloInterval OBJECT-TYPE This object defines the interval in which Hello (or keep-alive) packets are to be sent to the tunnel peer. The value zero effectively disables the sending of Hello packets. Modifications to this object have immediate effect. | 1.3.6.1.2.1.10.95.1.4.1.6 | Integer32 (0..3600) | read-write | current |
| l2tpTunnelConfigIdleTimeout OBJECT-TYPE This object defines the period of time that an established tunnel with no sessions will wait before disconnecting the tunnel. A value of zero indicates that the tunnel will disconnect immediately after the last session disconnects. A value of -1 leaves the tunnel up indefinitely. Modifications to this object have immediate effect. | 1.3.6.1.2.1.10.95.1.4.1.7 | Integer32 (-1..86400) | read-write | current |
| l2tpTunnelConfigControlRWS OBJECT-TYPE This object defines the control channel receive window size. It specifies the maximum number of packets the tunnel peer can send without waiting for an acknowledgement from this peer. This object cannot be modified when the tunnel is in a con- necting or connected state. | 1.3.6.1.2.1.10.95.1.4.1.8 | Integer32 (1..65535) | read-write | current |
| l2tpTunnelConfigControlMaxRetx OBJECT-TYPE This object defines the number of retransmissions which the tunnel will attempt before assuming that the peer is no longer responding. A value of zero indicates that this peer will not attempt to retransmit an unacknowledged control packet. Modifications to this object have immediate effect. | 1.3.6.1.2.1.10.95.1.4.1.9 | Integer32 (0..32) | read-write | current |
| l2tpTunnelConfigControlMaxRetxTO OBJECT-TYPE This object defines the maximum retransmission timeout interval which the tunnel will wait before retrans- mitting a control packet that has not been acknowledged. Modifications to this object have immediate effect. | 1.3.6.1.2.1.10.95.1.4.1.10 | Integer32 (1..32) | read-write | current |
| l2tpTunnelConfigPayloadSeq OBJECT-TYPE This object determines whether or not session payload packets will be requested to be sent with sequence numbers from tunnel peers belonging to this domain. The value onDemand(1) allows the L2TP implementation to initiate payload sequencing when necessary based on local information (e.g: during LCP/NCP negotiations or for CCP). The value never(2) indicates that L2TP will never initiate sequencing but will do sequencing if asked. The value always(3) indicates that L2TP will send the Sequencing Required AVP during session establishment. Modifications to this object have immediate effect. | 1.3.6.1.2.1.10.95.1.4.1.11 | INTEGER {onDemand(1), never(2), always(3)} | read-write | current |
| l2tpTunnelConfigReassemblyTO OBJECT-TYPE This object defines the number of milliseconds that this tunnel will wait before processing payload packets that were received out of sequence (which are waiting for the packet(s) to put them in sequence). A low value increases the chance of delayed packets to be discarded (which MAY cause the PPP decompression engine to reset) while a high value may cause more queuing and possibly degrade throughput if packets are truly lost. The default value for this object is zero which will result in all delayed packets being lost. Modifications to this object have immediate effect. | 1.3.6.1.2.1.10.95.1.4.1.12 | L2tpMilliSeconds | read-write | current |
| l2tpTunnelConfigTransport OBJECT-TYPE This object defines the underlying transport media that is in use for this tunnel entry. Different tunnel transports may define MIB extensions to the L2TP tunnel table to realize the transport layer. For example if the value of this object is 'udpIp' then the value of ifIndex for this table may be used to determine state from the l2tpUdpStatsTable. This object cannot be modified when the tunnel is in a connecting or connected state. | 1.3.6.1.2.1.10.95.1.4.1.13 | INTEGER {other(1), none(2), udpIp(3), frameRelay(4), atm(5)} | read-write | current |
| l2tpTunnelConfigDrainTunnel OBJECT-TYPE Setting this object to 'true' will prevent any new session from being either initiated or accepted but does NOT disconnect any active sessions for this tunnel. Note that when this occurs the l2tpTunnelStatsDrainingTunnel status object of this tunnel should reflect that it is 'draining'. To cancel a drain this object should be set to false(2). Setting this object to false(2) when the L2TP objects l2tpDrainTunnels or l2tpDomainConfigDrainTunnels is true(1) has no affect, this tunnels will continue to drain. | 1.3.6.1.2.1.10.95.1.4.1.14 | TruthValue | read-write | current |
| l2tpTunnelConfigProxyPPPAuth OBJECT-TYPE This object is used to configure the sending or acceptance of the session PPP Proxy Authentication AVP's on the LAC or LNS. | 1.3.6.1.2.1.10.95.1.4.1.15 | TruthValue | read-write | current |
| l2tpTunnelStatsTable OBJECT-TYPE The L2TP tunnel status and statistics table. This table contains objects that can be used to describe the current status and statistics of a single L2TP tunnel. There is a 1-1 correspondence between conceptual rows of this table and conceptual rows of the l2tpTunnelConfigTable. | 1.3.6.1.2.1.10.95.1.5 | not-accessible | current | |
| l2tpTunnelStatsEntry OBJECT-TYPE An L2TP tunnel interface stats entry. | 1.3.6.1.2.1.10.95.1.5.1 | not-accessible | current | |
| l2tpTunnelStatsLocalTID OBJECT-TYPE This object contains the local tunnel Identifier. | 1.3.6.1.2.1.10.95.1.5.1.1 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsRemoteTID OBJECT-TYPE This object contains the remote tunnel Identifier. | 1.3.6.1.2.1.10.95.1.5.1.2 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsState OBJECT-TYPE This field contains the current state of the control tunnel. | 1.3.6.1.2.1.10.95.1.5.1.3 | INTEGER {tunnelIdle(1), tunnelConnecting(2), tunnelEstablished(3), tunnelDisconnecting(4)} | read-only | current |
| l2tpTunnelStatsInitiated OBJECT-TYPE This object indicates whether the tunnel was initiated locally or by the remote tunnel peer. | 1.3.6.1.2.1.10.95.1.5.1.4 | INTEGER {locally(1), remotely(2)} | read-only | current |
| l2tpTunnelStatsRemoteHostName OBJECT-TYPE This object contains the host name as discovered during the tunnel establishment phase (via the Host Name AVP) of the L2TP peer. If the tunnel is idle this object should maintain its value from the last time it was connected. | 1.3.6.1.2.1.10.95.1.5.1.5 | SnmpAdminString | read-only | current |
| l2tpTunnelStatsRemoteVendorName OBJECT-TYPE This object identifies the vendor name of the peer's L2TP implementation. If the tunnel is idle this object should maintain its value from the last time it was connected. | 1.3.6.1.2.1.10.95.1.5.1.6 | SnmpAdminString | read-only | current |
| l2tpTunnelStatsRemoteFirmwareRev OBJECT-TYPE This object contains the tunnel peer's firmware revision number. If the tunnel is idle this object should maintain its value from the last time it was connected. | 1.3.6.1.2.1.10.95.1.5.1.7 | Integer32 | read-only | current |
| l2tpTunnelStatsRemoteProtocolVer OBJECT-TYPE This object describes the protocol version and revision of the tunnel peers implementation. The first octet contains the protocol version. The second octet contains the protocol revision. | 1.3.6.1.2.1.10.95.1.5.1.8 | OCTET STRING (SIZE(2)) | read-only | current |
| l2tpTunnelStatsInitialRemoteRWS OBJECT-TYPE This object contains the initial remote peer's receive window size as indicated by the tunnel peer (in the RWS AVP) during the tunnel establishment phase. If the tunnel is idle this object should maintain its value from the last time it was connected. | 1.3.6.1.2.1.10.95.1.5.1.9 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsBearerCaps OBJECT-TYPE This object describes the Bearer Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connected. | 1.3.6.1.2.1.10.95.1.5.1.10 | INTEGER {none(1), digital(2), analog(3), digitalAnalog(4)} | read-only | current |
| l2tpTunnelStatsFramingCaps OBJECT-TYPE This object describes the Framing Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connected. | 1.3.6.1.2.1.10.95.1.5.1.11 | INTEGER {none(1), sync(2), async(3), syncAsync(4)} | read-only | current |
| l2tpTunnelStatsControlRxPkts OBJECT-TYPE This object contains the number of control packets received on the tunnel. | 1.3.6.1.2.1.10.95.1.5.1.12 | Counter32 | read-only | current |
| l2tpTunnelStatsControlRxZLB OBJECT-TYPE This object returns a count of the number of Zero Length Body control packet acknowledgement packets that were received. | 1.3.6.1.2.1.10.95.1.5.1.13 | Counter32 | read-only | current |
| l2tpTunnelStatsControlOutOfSeq OBJECT-TYPE This object returns a count of the number of control packets that were not received in the correct order (as per the sequence number) on this tunnel including out of window packets. | 1.3.6.1.2.1.10.95.1.5.1.14 | Counter32 | read-only | current |
| l2tpTunnelStatsControlOutOfWin OBJECT-TYPE This object contains the number of control packets that were received outside of the offered receive window. It is implementation specific as to whether these packets are queued or discarded. | 1.3.6.1.2.1.10.95.1.5.1.15 | Counter32 | read-only | current |
| l2tpTunnelStatsControlTxPkts OBJECT-TYPE This object contains the number of control packets that were transmitted to the tunnel peer. | 1.3.6.1.2.1.10.95.1.5.1.16 | Counter32 | read-only | current |
| l2tpTunnelStatsControlTxZLB OBJECT-TYPE This object contains the number of Zero Length Body control packets transmitted to the tunnel peer. | 1.3.6.1.2.1.10.95.1.5.1.17 | Counter32 | read-only | current |
| l2tpTunnelStatsControlAckTO OBJECT-TYPE This object returns a count of the number of control packet timeouts due to the lack of a timely acknowledgement from the tunnel peer. | 1.3.6.1.2.1.10.95.1.5.1.18 | Counter32 | read-only | current |
| l2tpTunnelStatsCurrentRemoteRWS OBJECT-TYPE This object contains the current remote receive window size as determined by the local flow control mechanism employed. | 1.3.6.1.2.1.10.95.1.5.1.19 | Gauge32 (0..65535) | read-only | current |
| l2tpTunnelStatsTxSeq OBJECT-TYPE This object contains the next send sequence number for the control channel. | 1.3.6.1.2.1.10.95.1.5.1.20 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsTxSeqAck OBJECT-TYPE This object contains the send sequence number that the tunnel peer has acknowledged for the control channel. The flow control state can be determined by subtracting the l2tpTunnelStatsTxSeq from l2tpTunnelStatsTxSeqAck and comparing this value to l2tpTunnelStatsCurrentRemoteRWS (taking into consideration sequence number wraps). | 1.3.6.1.2.1.10.95.1.5.1.21 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsRxSeq OBJECT-TYPE This object contains the next receive sequence number expected to be received on this control channel. | 1.3.6.1.2.1.10.95.1.5.1.22 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsRxSeqAck OBJECT-TYPE This object contains the last receive sequence number that was acknowledged back to the tunnel peer for the control channel. | 1.3.6.1.2.1.10.95.1.5.1.23 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsTotalSessions OBJECT-TYPE This object contains the total number of sessions that this tunnel has successfully connected through to its tunnel peer since this tunnel was created. | 1.3.6.1.2.1.10.95.1.5.1.24 | Counter32 | read-only | current |
| l2tpTunnelStatsFailedSessions OBJECT-TYPE This object contains the total number of sessions that were initiated but failed to reach the established phase. | 1.3.6.1.2.1.10.95.1.5.1.25 | Counter32 | read-only | current |
| l2tpTunnelStatsActiveSessions OBJECT-TYPE This object contains the total number of sessions in the established state for this tunnel. | 1.3.6.1.2.1.10.95.1.5.1.26 | Gauge32 | read-only | current |
| l2tpTunnelStatsLastResultCode OBJECT-TYPE This object contains the last value of the result code as described in the Result Code AVP which caused the tunnel to disconnect. | 1.3.6.1.2.1.10.95.1.5.1.27 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsLastErrorCode OBJECT-TYPE This object contains the last value of the error code as described in the Result Code AVP which caused the tunnel to disconnect. | 1.3.6.1.2.1.10.95.1.5.1.28 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelStatsLastErrorMessage OBJECT-TYPE This object contains the last value of the optional message as described in the Result Code AVP which caused the tunnel to disconnect. | 1.3.6.1.2.1.10.95.1.5.1.29 | SnmpAdminString | read-only | current |
| l2tpTunnelStatsDrainingTunnel OBJECT-TYPE This object indicates if this tunnel is draining off sessions. This object will return false(2) when the tunnel is not draining sessions or after the last session has disconnected when the tunnel is in the draining state. | 1.3.6.1.2.1.10.95.1.5.1.30 | TruthValue | read-only | current |
| l2tpSessionStatsTable OBJECT-TYPE The L2TP session status and statistics table. This table contains the objects that can be used to describe the current status and statistics of a single L2TP tunneled session. | 1.3.6.1.2.1.10.95.1.7 | not-accessible | current | |
| l2tpSessionStatsEntry OBJECT-TYPE An L2TP session interface stats entry. | 1.3.6.1.2.1.10.95.1.7.1 | not-accessible | current | |
| l2tpSessionStatsTunnelIfIndex OBJECT-TYPE This object identifies the session's associated L2TP tunnel ifIndex value. | 1.3.6.1.2.1.10.95.1.7.1.1 | InterfaceIndex | not-accessible | current |
| l2tpSessionStatsIfIndex OBJECT-TYPE This object identifies the ifIndex value of the interface from which PPP packets are being tunneled. For example this could be a DS0 ifIndex on a LAC or it would be the PPP ifIndex on the LNS. | 1.3.6.1.2.1.10.95.1.7.1.2 | InterfaceIndex | read-only | current |
| l2tpSessionStatsLocalSID OBJECT-TYPE This object contains the local assigned session identifier for this session. | 1.3.6.1.2.1.10.95.1.7.1.3 | Integer32 (1..65535) | not-accessible | current |
| l2tpSessionStatsRemoteSID OBJECT-TYPE This object contains the remote assigned session identifier for this session. When a session is starting this value may be zero until the remote tunnel endpoint has responded. | 1.3.6.1.2.1.10.95.1.7.1.4 | Integer32 (0..65535) | read-only | current |
| l2tpSessionStatsUserName OBJECT-TYPE This object identifies the peer session name on this interface. This is typically the login name of the remote user. If the user name is unknown to the local tunnel peer then this object will contain a null string. | 1.3.6.1.2.1.10.95.1.7.1.5 | SnmpAdminString | read-only | current |
| l2tpSessionStatsState OBJECT-TYPE This object contains the current state of the session. | 1.3.6.1.2.1.10.95.1.7.1.6 | INTEGER {sessionIdle(1), sessionConnecting(2), sessionEstablished(3), sessionDisconnecting(4)} | read-only | current |
| l2tpSessionStatsCallType OBJECT-TYPE This object indicates the type of call and the role this tunnel peer is providing for this session. For example, lacIncoming(1) indicates that this tunnel peer is acting as a LAC and generated a Incoming-Call-Request to the tunnel peer (the LNS). Note that tunnel peers can be both LAC and LNS simultaneously. | 1.3.6.1.2.1.10.95.1.7.1.7 | INTEGER {lacIncoming(1), lnsIncoming(2), lacOutgoing(3), lnsOutgoing(4)} | read-only | current |
| l2tpSessionStatsCallSerialNumber OBJECT-TYPE This object contains the serial number that has been assigned to this session. | 1.3.6.1.2.1.10.95.1.7.1.8 | Unsigned32 | read-only | current |
| l2tpSessionStatsTxConnectSpeed OBJECT-TYPE This object returns the last known transmit baud rate for this session. | 1.3.6.1.2.1.10.95.1.7.1.9 | Unsigned32 | read-only | current |
| l2tpSessionStatsRxConnectSpeed OBJECT-TYPE This object returns the last known receive baud rate for this session established. | 1.3.6.1.2.1.10.95.1.7.1.10 | Unsigned32 | read-only | current |
| l2tpSessionStatsCallBearerType OBJECT-TYPE This object describes the bearer type of this session. | 1.3.6.1.2.1.10.95.1.7.1.11 | INTEGER {none(1), digital(2), analog(3)} | read-only | current |
| l2tpSessionStatsFramingType OBJECT-TYPE This object describes the framing type of this session. | 1.3.6.1.2.1.10.95.1.7.1.12 | INTEGER {none(1), sync(2), async(3)} | read-only | current |
| l2tpSessionStatsPhysChanId OBJECT-TYPE This object contains the physical channel identifier for the session. | 1.3.6.1.2.1.10.95.1.7.1.13 | Unsigned32 | read-only | current |
| l2tpSessionStatsDNIS OBJECT-TYPE This object identifies the Dialed Number Information String that the LAC obtained from the network for the session. If no DNIS was provided then a null string will be returned. | 1.3.6.1.2.1.10.95.1.7.1.14 | SnmpAdminString | read-only | current |
| l2tpSessionStatsCLID OBJECT-TYPE This object identifies the Calling Line ID that the LAC obtained from the network for the session. If no CLID was provided then a null string will be returned. | 1.3.6.1.2.1.10.95.1.7.1.15 | SnmpAdminString | read-only | current |
| l2tpSessionStatsSubAddress OBJECT-TYPE This object identifies the Sub Address that the LAC obtained from the network for the session. If no Sub Address was provided then a null string will be returned. | 1.3.6.1.2.1.10.95.1.7.1.16 | SnmpAdminString | read-only | current |
| l2tpSessionStatsPrivateGroupID OBJECT-TYPE This object identifies the Private Group Identifier used for this tunneled session. If no Private Group Identifier was provided then a null string will be returned. | 1.3.6.1.2.1.10.95.1.7.1.17 | SnmpAdminString | read-only | current |
| l2tpSessionStatsProxyLcp OBJECT-TYPE Indicates whether the LAC performed proxy LCP for this session. | 1.3.6.1.2.1.10.95.1.7.1.18 | TruthValue | read-only | current |
| l2tpSessionStatsAuthMethod OBJECT-TYPE This object contains the proxy authentication method employed by the LAC for the session. If l2tpSessionProxyLcp is false(2) this object should not be interpreted. | 1.3.6.1.2.1.10.95.1.7.1.19 | INTEGER {none(1), text(2), pppChap(3), pppPap(4), pppEap(5), pppMsChapV1(6), pppMsChapV2(7), other(8)} | read-only | current |
| l2tpSessionStatsSequencingState OBJECT-TYPE This object defines which tunnel peers have requested payload sequencing. The value of both(4) indicates that both peers have requested payload sequencing. | 1.3.6.1.2.1.10.95.1.7.1.20 | INTEGER {none(1), remote(2), local(3), both(4)} | read-only | current |
| l2tpSessionStatsOutSequence OBJECT-TYPE This object returns the total number of packets received for this session which were received out of sequence. | 1.3.6.1.2.1.10.95.1.7.1.21 | Counter32 | read-only | current |
| l2tpSessionStatsReassemblyTO OBJECT-TYPE This object returns the number of reassembly timeouts that have occurred for this session. | 1.3.6.1.2.1.10.95.1.7.1.22 | Counter32 | read-only | current |
| l2tpSessionStatsTxSeq OBJECT-TYPE This object contains the next send sequence number for for this session. | 1.3.6.1.2.1.10.95.1.7.1.23 | Integer32 (0..65535) | read-only | current |
| l2tpSessionStatsRxSeq OBJECT-TYPE This object contains the next receive sequence number expected to be received on this session. | 1.3.6.1.2.1.10.95.1.7.1.24 | Integer32 (0..65535) | read-only | current |
| l2tpTunnelMapTable OBJECT-TYPE The L2TP Tunnel index mapping table. This table is intended to assist management applications to quickly determine what the ifIndex value is for a given local tunnel identifier. | 1.3.6.1.2.1.10.95.1.8 | not-accessible | current | |
| l2tpTunnelMapEntry OBJECT-TYPE An L2TP tunnel index map entry. | 1.3.6.1.2.1.10.95.1.8.1 | not-accessible | current | |
| l2tpTunnelMapLocalTID OBJECT-TYPE This object contains the local tunnel Identifier. | 1.3.6.1.2.1.10.95.1.8.1.1 | Integer32 (1..65535) | not-accessible | current |
| l2tpTunnelMapIfIndex OBJECT-TYPE This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type L2TP. | 1.3.6.1.2.1.10.95.1.8.1.2 | InterfaceIndex | read-only | current |
| l2tpSessionMapTable OBJECT-TYPE The L2TP Session index mapping table. This table is intended to assist management applications to map interfaces to a tunnel and session identifier. | 1.3.6.1.2.1.10.95.1.9 | not-accessible | current | |
| l2tpSessionMapEntry OBJECT-TYPE An L2TP Session index map entry. | 1.3.6.1.2.1.10.95.1.9.1 | not-accessible | current | |
| l2tpSessionMapIfIndex OBJECT-TYPE This object identifies the ifIndex value of the interface which is receiving or sending its packets over an L2TP tunnel. For example this could be a DS0 ifIndex on a LAC or a PPP ifIndex on the LNS. | 1.3.6.1.2.1.10.95.1.9.1.1 | InterfaceIndex | not-accessible | current |
| l2tpSessionMapTunnelIfIndex OBJECT-TYPE This object identifies the sessions associated L2TP tunnel ifIndex value. When this object is set it provides a binding between a particular interface identified by l2tpSessionMapIfIndex to a particular tunnel. | 1.3.6.1.2.1.10.95.1.9.1.2 | InterfaceIndex | read-create | current |
| l2tpSessionMapLocalSID OBJECT-TYPE This object contains the local assigned session identifier for this session. | 1.3.6.1.2.1.10.95.1.9.1.3 | Integer32 (1..65535) | read-only | current |
| l2tpSessionMapStatus OBJECT-TYPE The status of this session map entry. | 1.3.6.1.2.1.10.95.1.9.1.4 | RowStatus | read-create | current |
| l2tpTransports OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.3 | |||
| l2tpTransportIpUdp OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.3.1 | |||
| l2tpIpUdpObjects OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.3.1.1 | |||
| l2tpUdpStatsTable OBJECT-TYPE The L2TP UDP/IP transport stats table. This table contains objects that can be used to describe the current status and statistics of the UDP/IP L2TP tunnel transport. | 1.3.6.1.2.1.10.95.3.1.1.2 | not-accessible | current | |
| l2tpUdpStatsEntry OBJECT-TYPE An L2TP UDP/IP transport stats entry. | 1.3.6.1.2.1.10.95.3.1.1.2.1 | not-accessible | current | |
| l2tpUdpStatsIfIndex OBJECT-TYPE This value for this object is equal to the value of ifIndex of the Interfaces MIB for tunnel interfaces of type L2TP and which have a L2TP transport of UDP/IP. | 1.3.6.1.2.1.10.95.3.1.1.2.1.1 | InterfaceIndex | not-accessible | current |
| l2tpUdpStatsPeerPort OBJECT-TYPE This object reflects the peer's UDP port number used for this tunnel. When not known a value of zero should be returned. | 1.3.6.1.2.1.10.95.3.1.1.2.1.2 | Integer32 (0..65535) | read-only | current |
| l2tpUdpStatsLocalPort OBJECT-TYPE This object reflects the local UDP port number that this tunnel is bound to. | 1.3.6.1.2.1.10.95.3.1.1.2.1.3 | Integer32 (0..65535) | read-only | current |
| l2tpIpUdpTraps OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.3.1.2 | |||
| l2tpConformance OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.4 | |||
| l2tpGroups OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.4.1 | |||
| l2tpCompliances OBJECT-IDENTITY | 1.3.6.1.2.1.10.95.4.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| l2tpTunnelAuthFailure NOTIFICATION-TYPE A l2tpTunnelAuthFailure trap signifies that an attempt to establish a tunnel to a remote peer has failed authentication. | 1.3.6.1.2.1.10.95.0.1 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| l2tpConfigGroup OBJECT-GROUP A collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | 1.3.6.1.2.1.10.95.4.1.1 | current |
| l2tpStatsGroup OBJECT-GROUP A collection of objects providing status and statistics of the L2TP protocol, tunnels and sessions. | 1.3.6.1.2.1.10.95.4.1.2 | current |
| l2tpIpUdpGroup OBJECT-GROUP A collection of objects providing status and statistics of the L2TP UDP/IP transport layer. | 1.3.6.1.2.1.10.95.4.1.3 | current |
| l2tpDomainGroup OBJECT-GROUP A collection of objects providing configuration, status and statistics of L2TP tunnel domains. | 1.3.6.1.2.1.10.95.4.1.4 | current |
| l2tpMappingGroup OBJECT-GROUP A collection of objects providing index mapping. | 1.3.6.1.2.1.10.95.4.1.5 | current |
| l2tpSecurityGroup OBJECT-GROUP A collection of objects providing L2TP security configuration. | 1.3.6.1.2.1.10.95.4.1.6 | current |
| l2tpTrapGroup NOTIFICATION-GROUP A collection of L2TP trap events as specified in NOTIFICATION-TYPE constructs. | 1.3.6.1.2.1.10.95.4.1.7 | current |
| l2tpHCPacketGroup OBJECT-GROUP A collection of objects providing High Capacity 64-bit counter objects. | 1.3.6.1.2.1.10.95.4.1.8 | current |
| l2tpMIBFullCompliance MODULE-COMPLIANCE When this MIB is implemented with support for read-create and read-write, then such an implementation can claim full compliance. Such an implementation can then be both monitored and configured with this MIB. | 1.3.6.1.2.1.10.95.4.2.1 | current |
| l2tpMIBReadOnlyCompliance MODULE-COMPLIANCE When this MIB is implemented without support for read-create and read-write (i.e. in read-only mode), then such an implementation can claim read-only compliance. Such an implementation can then be monitored but can not be configured with this MIB. | 1.3.6.1.2.1.10.95.4.2.2 | current |