JUNIPER-SOAM-PM-MIB

TEXTUAL-CONVENTION

This enumeration data type defines the availability of a session, measured by a loss measurement session. The valid enumerated values associated with this type are: available(1) indicates the MEP is available. unavailable(2) indicates the MEP is unavailable. unknown(3) indicates the availability is not known, for instance because insufficient time has passed to make an availability calculation, the time has been excluded because of a maintenance interval, or because availability measurement is not enabled.

TEXTUAL-CONVENTION

This enumeration data type indicates the type of data pattern to be sent in an OAM PDU Data TLV. The valid enumerated values associated with this type are: zeroPattern(1) indicates the Data TLV contains all zeros onesPattern(2) indicates the Data TLV contains all ones

TEXTUAL-CONVENTION

This enumeration data type is used to distinguish between measurement bins for Frame Delay, Frame Delay Range, and Inter-frame Delay variation. The valid enumerated values associated with this type are: twoWayFrameDelay(1) indicates a measurement bin for two-way Frame Delay. forwardFrameDelay(2) indicates a measurement bin for one-way Frame Delay in the forward direction. backwardFrameDelay(3) indicates a measurement bin for one-way Frame Delay in the backward direction. twoWayIfdv(4) indicates a measurement bin for two-way Inter-frame Delay Variation. forwardIfdv(5) indicates a measurement bin for one-way Inter-frame Delay Variation in the forward direction. backwardIfdv(6) indicates a measurement bin for one-way Inter-frame Delay Variation in the backward direction. twoWayFrameDelayRange(7) indicates a measurement bin for two-way Frame Delay Range. forwardFrameDelayRange(8) indicates a measurement bin for one-way Frame Delay Range in the forward direction. backwardFrameDelayRange(9) indicates a measurement bin for one-way Frame Delay Range in the backward direction.

TEXTUAL-CONVENTION

This enumeration data type indicates the operation type start or end time to indicate when an OAM operation is initiated or stopped. The valid enumerated values associated with this type are: none(1) The operation is never started or is stopped immediately if used to indicate a start time, or the operation never ends if it is used to indicate an end time immediate(2) The operation is to begin immediately relative(3) The operation is to begin at a relative time from the current time or stop a relative time after it has started fixed(4) The operation is to begin/stop at the given UTC time/date

TEXTUAL-CONVENTION

This enumeration data type indicates the type of test pattern to be sent in an OAM PDU Test TLV. The valid enumerated values associated with this type are: null(1) Null signal without CRC-32 nullCrc32(2) Null signal with CRC-32 prbs(3) PRBS 2^31-1 without CRC-32 prbsCrc32(4) PRBS 2^31-1 with CRC-32

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This table is an extension of the dot1agCfmMepTable and rows are automatically added or deleted from this table based upon row creation and destruction of the dot1agCfmMepTable. This table represents the local MEP PM configuration table. The primary purpose of this table is provide local parameters for the SOAM PM function found in [Y.1731] and [MEF SOAM-PM] and instantiated at a MEP.

OBJECT-TYPE

The conceptual row of jnxSoamPmMepTable.

OBJECT-TYPE

This object contains an unused value for a PM session number on a MEP that can be used for either LM or DM sessions, or a zero to indicate that none exist. This value needs to be read in order to find an available index for row-creation of a PM session on a MEP and then used when a row is created. This value is automatically updated by the SNMP Agent after the row is created. Referential integrity is necessary, i.e., the index needs to be persistent upon a reboot or restart of a device. The index is never to be reused for other PM sessions on the same MEP while this session is active, or until it wraps to zero. The index value keeps increasing up to that time. This is to facilitate access control based on a fixed index for an EMS, since the index is not reused. This object is an extension of the dot1agCfmMepTable and the object is automatically added or deleted based upon row creation and destruction of the dot1agCfmMepTable.

OBJECT-TYPE

This object specifies whether the Loss Measurement (LMM) single-ended Responder is enabled. The value 'true' indicates the single-ended Loss Measurement Responder is enabled and if a LMM message is received a LMR will be sent in reply. The value 'false' indicates the single-ended Loss Measurement Responder is disabled. If a LMM message is received no response will be sent and the message will be discarded. This object needs to be persistent upon reboot or restart of a device. A MEP can be both a single-ended Responder and Controller simultaneously.

OBJECT-TYPE

This object specifies whether the Synthetic Loss Measurement (SLM) single-ended Responder is enabled. The value 'true' indicates the single-ended SLM Responder is enabled and if a SLM message is received a SLR will be sent in reply. The value 'false' indicates the single-ended SLM Responder is disabled. If a SLM message is received no response will be sent and the message will be discarded. This object needs to be persistent upon reboot or restart of a device. A MEP can be both a single-ended Responder and Controller simultaneously.

OBJECT-TYPE

This object specifies whether the Delay Measurement (DMM) single ended Responder is enabled. The value 'true' indicates the single-ended Delay Measurement Responder is enabled and if a DMM message is received a DMR will be sent in reply. The value 'false' indicates the single-ended Delay Measurement Responder is disabled. If a DMM message is received no response will be sent and the message will be discarded. This object needs to be persistent upon reboot or restart of a device. A MEP can be both a single-ended Responder and Controller simultaneously.

OBJECT-IDENTITY

OBJECT-TYPE

This table includes configuration objects and operations for the Frame Loss Measurement function defined in [Y.1731] and [MEF SOAM-PM]. Each row in the table represents a Loss Measurement session for the defined MEP. This table uses four indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific LM session on the selected MEP. A Loss Measurement session is created on an existing MEP by first accessing the jnxSoamPmMepOperNextIndex object and using this value as the jnxSoamLmCfgIndex in the row creation. Some writable objects in this table are only applicable in certain cases (as described under each object), and attempts to write values for them in other cases will be ignored. The writable objects in this table need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamLmCfgTable.

OBJECT-TYPE

An index to the Loss Measurement Configuration table which indicates the specific measurement session for the MEP. jnxSoamPmMepOperNextIndex needs to be inspected to find an available index for row-creation. Referential integrity is necessary, i.e., the index needs to be persistent upon a reboot or restart of a device. The index is never reused for other PM sessions on the same MEP while this session is active. The index value keeps increasing until it wraps to 0. This is to facilitate access control based on a fixed index for an EMS, since the index is not reused.

OBJECT-TYPE

This object specifies what type of Loss Measurement will be performed. lmLmm(1) LMM SOAM PDU generated and received LMR responses tracked lmSlm(2) SLM SOAM PDU generated and received SLR responses tracked lmCcm(3) CCM SOAM PDU generated and received CCM PDUs tracked The lmSlm value is required. The lmLmm and lmCcm values are optional. The lmCcm loss measurement values are only valid for a point-to-point MEG. Multipoint MEGs may give unreliable loss measurements. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object indicates the version of the PDUs used to perform Loss Measurement. The value is placed in the Version field of the PDU and indicates that the PDU format used is the format defined in Y.1731 with that version. The exact PDUs to use are specified by this object in combination with jnxSoamLmCfgType. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies whether the Loss Measurement session is enabled. The value 'true' indicates the Loss Measurement session is enabled and SOAM PDUs are sent and/or measurements are collected when the session is running according to the scheduling objects (start time, stop time, etc.). The value 'false' indicates the Loss Measurement session is disabled and SOAM PDUs are not sent and/or measurements collected. For a Loss Measurement session to be removed the row is deleted in order to release internal resources. This object can written/modified after row creation time. If the LM session is enabled it resumes after shutdown/restart. If the LM session is disabled the current Measurement Interval is stopped, if it in process at the time, and all the in process calculations for the partially completed Measurement Interval are finalized. This object does not affect whether the single-ended Responder is enabled or not, which is enabled or disabled by the jnxSoamPmMepLmSingleEndedResponder and jnxSoamPmMepSlmSingleEndedResponder objects.

OBJECT-TYPE

A vector of bits that indicates the type of SOAM LM counters found in the jnxSoamLmMeasuredStatsTable, jnxSoamLmCurrentStatsTable, jnxSoamLmHistoryStatsTable that are enabled. that are enabled. A bit set to '1' enables the specific SOAM LM counter. A bit set to '0' disables the SOAM LM counter. If a particular SOAM LM counter is not supported the BIT value is set to '0'. Not all SOAM LM counters are supported for all SOAM LM types. This object can only be written at row creation time and cannot be modified once it has been created. bForwardTransmitedFrames (0) Enables/disables the jnxSoamLmCurrentStatsForwardTransmittedFrames and jnxSoamLmHistoryStatsForwardTransmittedFrames counters. bForwardReceivedFrames(1) Enables/disables the jnxSoamLmCurrentStatsForwardReceivedFrames and jnxSoamLmHistoryStatsForwardReceivedFrames counters. bForwardMinFlr(2) Enables/disables the jnxSoamLmCurrentStatsForwardMinFlr and jnxSoamLmHistoryStatsForwardMinFlr counters. bForwardMaxFlr(3) Enables/disables the jnxSoamLmCurrentStatsForwardMaxFlr and jnxSoamLmHistoryStatsForwardMaxFlr counters. bForwardAvgFlr(4) Enables/disables the jnxSoamLmCurrentStatsForwardAvgFlr and jnxSoamLmHistoryStatsForwardAvgFlr counters. bBackwardTransmitedFrames(5) Enables/disables the jnxSoamLmCurrentStatsBackwardTransmittedFrames and jnxSoamLmHistoryStatsBackwardTransmittedFrames counters. bBackwardReceivedFrames(6) Enables/disables the jnxSoamLmCurrentStatsBackwardReceivedFrames and jnxSoamLmHistoryStatsBackwardReceivedFrames counters. bBackwardMinFlr(7) Enables/disables the jnxSoamLmCurrentStatsBackwardMinFlr and jnxSoamLmHistoryStatsBackwardMinFlr counters. bBackwardMaxFlr(8) Enables/disables the jnxSoamLmCurrentStatsBackwardMaxFlr and jnxSoamLmHistoryStatsBackwardMaxFlr counters. bBackwardAvgFlr(9) Enables/disables the jnxSoamLmCurrentStatsBackwardAvgFlr and jnxSoamLmHistoryStatsBackwardAvgFlr counters. bSoamPdusSent (10) Enables/disables the jnxSoamLmCurrentStatsSoamPdusSent and jnxSoamLmHistoryStatsSoamPdusSent counters. bSoamPdusReceivedbReceivedMeasurements (11) Enables/disables the jnxSoamLmCurrentStatsSoamPdusReceived and jnxSoamLmHistoryStatsSoamPdusReceived counters. bAvailForwardHighLoss(12) Enables/disables the jnxSoamLmCurrentAvailStatsForwardHighLoss and jnxSoamLmHistoryAvailStatsForwardHighLoss counters. bAvailForwardConsecutiveHighLoss(13) Enables/disables the jnxSoamLmCurrentAvailStatsForwardConsecutiveHighLoss and jnxSoamLmHistoryAvailStatsForwardConsecutiveHighLoss counters. bAvailForwardAvailable(14) Enables/disables the jnxSoamLmCurrentAvailStatsForwardAvailable and jnxSoamLmHistoryAvailStatsForwardAvailable counters. bAvailForwardUnavailable(15) Enables/disables the jnxSoamLmCurrentAvailStatsForwardUnavailable and jnxSoamLmHistoryAvailStatsForwardUnavailable counters. bAvailForwardMinFlr(16) Enables/disables the jnxSoamLmCurrentAvailStatsForwardMinFlr and jnxSoamLmHistoryAvailStatsForwardMinFlr counters. bAvailForwardMaxFlr(17) Enables/disables the jnxSoamLmCurrentAvailStatsForwardMaxFlr and jnxSoamLmHistoryAvailStatsForwardMaxFlr counters. bAvailForwardAvgFlr(18) Enables/disables the jnxSoamLmCurrentAvailStatsForwardAvgFlr and jnxSoamLmHistoryAvailStatsForwardAvgFlr counters. bAvailBackwardHighLoss(19) Enables/disables the jnxSoamLmCurrentAvailStatsBackwardHighLoss and jnxSoamLmHistoryAvailStatsBackwardHighLoss counters. bAvailBackwardConsecutiveHighLoss(20) Enables/disables the jnxSoamLmCurrentAvailStatsBackwardConsecutiveHighLoss and jnxSoamLmHistoryAvailStatsBackwardConsecutiveHighLoss counters. bAvailBackwardAvailable(21) Enables/disables the jnxSoamLmCurrentAvailStatsBackwardAvailable and jnxSoamLmHistoryAvailStatsBackwardAvailable counters. bAvailBackwardUnavailable(22) Enables/disables the jnxSoamLmCurrentAvailStatsBackwardUnavailable and jnxSoamLmHistoryAvailStatsBackwardUnavailable counters. bAvailBackwardMinFlr(23) Enables/disables the jnxSoamLmCurrentAvailStatsBackwardMinFlr and jnxSoamLmHistoryAvailStatsBackwardMinFlr counters. bAvailBackwardMaxFlr(24) Enables/disables the jnxSoamLmCurrentAvailStatsBackwardMaxFlr and jnxSoamLmHistoryAvailStatsBackwardMaxFlr counters. bAvailBackwardAvgFlr(25) Enables/disables the jnxSoamLmCurrentAvailStatsBackwardAvgFlr and jnxSoamLmHistoryAvailStatsBackwardAvgFlr counters. Enables/disables the jnxSoamLmCurrentStatsSoamPdusReceived and jnxSoamLmHistoryStatsSoamPdusReceived counters. bMeasuredStatsForwardMeasuredFlr(26) Enables/disables the jnxSoamLmMeasuredStatsForwardFlr counter. bMeasuredStatsBackwardMeasuredFlr(27) Enables/disables the jnxSoamLmMeasuredStatsBackwardFlr counter. bMeasuredStatsAvailForwardStatus(28) Enables/disables the jnxSoamLmMeasuredStatsAvailForwardStatus counter. bMeasuredStatsAvailBackwardStatus(29) Enables/disables the jnxSoamLmMeasuredStatsAvailBackwardStatus counter.

OBJECT-TYPE

This object specifies the interval between Loss Measurement OAM message transmission. For Loss Measurement monitoring applications the default value is 1 sec. This object is not applicable if jnxSoamLmCfgType is set to lmCcm and is ignored for that Loss Measurement Type. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the Loss Measurement OAM message priority as well as the priority of the service/OAM traffic to be monitored. Only frames of the same Class of Service are counted. The default value is to be the value which yields the lowest frame loss. This object is not applicable if jnxSoamLmCfgType is set to lmCcm. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the Loss Measurement frame size between 64 bytes and the maximum transmission unit of the EVC. The range of frame sizes from 64 through 2000 octets need to be supported, and the range of frame sizes from 2001 through 9600 octets is suggested be supported. The adjustment to the frame size of the standard frame size is accomplished by the addition of a Data or Test TLV. A Data or Test TLV is only added to the frame if the frame size is greater than 64 bytes. This object is only valid for the entity transmitting the Loss Measurement frames, type 'lmSlm', and is ignored by the entity receiving frames. It is not applicable for the 'lmCcm' or 'lmLmm' types. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the LM data pattern included in a Data TLV when the size of the LM frame is determined by the jnxSoamLmFrameSize object and jnxoamLmTestTlvIncluded is 'false'. If the frame size object does not define the LM frame size or jnxSoamLmTestTlvIncluded is 'true' the value of this object is ignored. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

Indicates whether a Test TLV or Data TLV is included when the size of the LM frame is determined by the jnxSoamLmFrameSize object. A value of 'true' indicates that the Test TLV is to be included. A value of 'false' indicates that the Data TLV is to be included. If the frame size object does not define the LM frame size the value of this object is ignored. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the type of test pattern to be sent in the LM frame Test TLV when the size of LM PDU is determined by the jnxSoamLmFrameSize object and jnxSoamLmTestTlvIncluded is 'true'. If the frame size object does not define the LM frame size or jnxSoamLmTestTlvIncluded is 'false' the value of this object is ignored. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the number of completed Measurement Intervals to store in the history statistic table (jnxSoamLmHistoryStatsTable) At least 32 completed Measurement Intervals need to be stored. 96 Measurement Intervals are recommended to be stored. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

The Maintenance Association End Point Identifier of another MEP in the same Maintenance Association to which the SOAM LM frame is to be sent. This address will be used if the value of the column jnxSoamLmDestIsMepId is 'true'. A value of zero means that the destination MEP ID has not been configured. This object is only valid for the entity transmitting the Loss Measurement frames, types 'lmLmm' and 'lmSlm'. It is not applicable for the 'lmCcm' type. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

A value of 'true' indicates that MEPID of the target MEP is used for SOAM LM frame transmission. A value of 'false' indicates that the MAC address of the target MEP is used for SOAM LM frame transmission. This object is only valid for the entity transmitting the Loss Measurement frames, types 'lmLmm' and 'lmSlm'. It is not applicable for the 'lmCcm' type. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the type of start time of the SOAM LM session. The start time can be disabled (none), immediate, relative, or fixed. The value of 'none' is illegal and a write error will be returned if this value is used. The value of 'immediate' starts the SOAM LM session when the jnxSoamLmCfgEnabled is true. The value of 'fixed' starts the SOAM LM session when the jnxSoamLmFixedStartDateAndTime is less than or equal to the current system date and time and jnxSoamLmCfgEnabled is true. This value is used to implement an On-Demand fixed time PM session. The value of 'relative' starts the SOAM LM session when the current system date and time minus the jnxSoamLmRelativeStartTime is greater than or equal to the system date and time when the jnxSoamLmStartTimeType object was written and jnxSoamLmCfgEnabled is true. This value is used to implement an On-Demand relative time PM session. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the fixed start date/time for the SOAM Loss Measurement session. This object is used only used if jnxSoamLmStartTimeType is 'fixed' and is ignored otherwise. The default value is year 0000, month 01, day 01, time 00:00:00.00. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the relative start time, from the current system time, for the SOAM LM session. This object is used only if jnxSoamLmStartTimeType is 'relative' and is ignored otherwise. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies a configurable repetition time between Measurement Intervals in a Loss Measurement session, in seconds. If the value is 0 (none), there is no time gap between the end of one Measurement Interval and the start of a new Measurement Interval. This is the normal usage case. If the value is greater than 0 but less than or equal to the measurement interval, an error is returned. If the value is greater than one Measurement Interval there is time gap between the end of one Measurement Interval and the start of the next Measurement Interval. The repetition time specifies the time between the start of consecutive Measurement Intervals; hence the gap between the end of one Measurement Interval and the start of the next is equal to the difference between the repetition time and the measurement interval. During this gap, no SOAM PDUs are sent for this session and no measurements are made. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies whether the Measurement Intervals for the Loss Measurement session are aligned with a zero offset to real time. The value 'true' indicates that each Measurement Interval starts at a time which is aligned to NE time source hour, if the repetition time (or the Measurement Interval, if the repetition time is 0) is a factor of an hour, i.e. 60min/15min = 4. For instance, a Measurement Interval/repetition time of 15 minutes would stop/start the Measurement Interval at 0, 15, 30, and 45 minutes of an hour. A Measurement Interval/Repetition Time of 7 minutes would not align to the hour since 7 minutes is NOT a factor of an hour, i.e. 60min/7min = 8.6. In this case the behavior is the same as if the object is set to 'false'. The value 'false' indicates that the first Measurement Interval starts at an arbitrary time and each subsequent Measurement Interval starts at a time which is determined by jnxSoamLmCfgRepetitionTime. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the offset in minutes from the time of day value if jnxSoamLmCfgAlignMeasurementIntervals is 'true' and the repetition time is a factor of 60 minutes. If not, the value of this object is ignored. If the Measurement Interval is 15 minutes and jnxSoamLmCfgAlignMeasurementIntervals is true and if this object was set to 5 minutes, the Measurement Intervals would start at 5, 20, 35, 50 minutes past each hour. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object indicates whether the current session is defined to be 'Proactive' or 'On-Demand'. A value of 'proactive' indicates the current session is 'Proactive'. A value of 'onDemand' indicates the current session is 'On-Demand'. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object indicates the current status of the LM session. A value of 'active' indicates the current LM session is active, i.e. the current time lies between the start time and the stop time, and jnxSoamLmCfgEnabled is true. A value of 'notActive' indicates the current LM session is not active, i.e. it has not started yet, has stopped upon reaching the stop time, or is disabled.

OBJECT-TYPE

This object when written clears the Loss Measurement history Table (jnxSoamLmHistoryStatsTable) - all rows are deleted. When read the value always returns 'false'. Writing this value does not change the current stat table, nor any of the items in the configuration table. Writing this value during row creation has no effect.

OBJECT-TYPE

The status of the row. The writable columns in a row cannot be changed if the row is active, except for jnxSoamLmCfgHistoryClear and jnxSoamLmCfgEnabled objects. All columns must have a valid value before a row can be activated.

OBJECT-TYPE

This object specifies the Measurement Interval for FLR statistics, in minutes. A Measurement Interval of 15 minutes needs to be supported, other intervals may be supported. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

The Target or Destination MAC Address Field to be transmitted. If jnxSoamLmCfgType is 'lmCcm', the destination MAC address is always a multicast address indicating the level of the MEG: 01-80-c2-00-00-3y, where y is the level of the MEG. An error is returned if this object is set to any other value. If jnxSoamLmCfgType is 'lmLmm' or 'lmSlm', the destination address is the unicast address of the destination MEP. An error is returned if this object is set to a multicast address. This address will be used if the value of the object mefSoamLmDestIsMepId is 'false'. This object is only valid for the entity transmitting the SOAM LM frames and is ignored by the entity receiving SOAM LM frames. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the type of stop time to terminate the SOAM LM session. The stop time can be forever (none), relative, or fixed. The value of 'none' indicates that the SOAM LM session never ends once it has started unless it the session is disabled. The value of 'immediate' is illegal and a write error will be returned if this value is used. The value of 'fixed' stops the SOAM LM session when the jnxSoamLmFixedStopDateAndTime is less than or equal to the current system date and time. This value is used to implement an On-Demand fixed time PM session. The value of 'relative' stops the SOAM LM session when the time indicated by jnxSoamLmRelativeStopTime has passed since the session start time as determined by the jnxSoamLmCfgStartTimeType, jnxSoamLmCfgFixedStartDateAndTime and jnxSoamLmCfgRelativeStartTime objects. This value is used to implement an On-Demand relative time PM session. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the fixed stop date/time for the SOAM Loss Measurement session. This object is used only used if jnxSoamLmStopTimeType is 'fixed' and is ignored otherwise. The default value is year 0000, month 01, day 01, time 00:00:00.00. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the relative stop time, from the session start time, to stop the SOAM LM session. This object is used only if jnxSoamLmStopTimeType is 'relative' and is ignored otherwise. object can only be written at row creation time 1922 and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the availability Measurement Interval in minutes. A Measurement Interval of 15 minutes is to be supported, other intervals can be supported. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies a configurable number of consecutive loss measurement PDUs to be used in evaluating the availability/unavailability status of each availability indicator per MEF 10.2.1. Loss Measurement PDUs (LMMs, CCMs or SLMs) are sent regularly with a period defined by jnxSoamLmCfgMessagePeriod. Therefore, this object, when multiplied by mefSoamLmCfgMessagePeriod, 2050 is equivalent to is equivalent to the Availability parameter of 'delta_t' as specified by MEF 10.2.1. If the jnxSoamLmCfgType is lmLMM or lmCCM, this object defines the number of LMM or CCM PDUs transmitted during each 'delta_t' period. The Availability flr for a given 'delta_t' can be calculated based on the counters in the last LMM/R or CCM during this 'delta_t' and the last LMM/R or CCM in the previous 'delta_t'. If the jnxSoamLmCfgType is lmSLM, this object defines the number of SLM PDUs transmitted during each 'delta_t' period. The Availability flr for a given 'delta_t' is calculated based on the number of those SLM PDUs that are lost. If the jnxSoamLmCfgType is lmLMM or lmCCM, the number range of 1 through 10 must be supported. The number range of 10 through 1000000 may be supported, but is not mandatory. If the jnxSoamLmCfgType is lmSLM, the number range of 10 through 100 must be supported. The number range of 100 through 1000000 may be supported, but is not mandatory. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies a configurable availability threshold to be used in evaluating the availability/unavailability status of an availability indicator per MEF 10.2.1. The availability threshold range of 0.00 (0) through 1.00 (100000) is supported. This parameter is equivalent to the Availability parameter of 'C' as specified by MEF 10.2.1. Units are in milli-percent, where 1 indicates 0.001 percent. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies a configurable number of consecutive availability indicators to be used to determine a change in the availability status as indicated by MEF 10.2.1. This parameter is equivalent to the Availability parameter of 'n' as specified by MEF 10.2.1. The number range of 1 through 10 must be supported. The number range of 1 through 1000 may be supported, but is not mandatory. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies a configurable number of consecutive availability indicators to be used for assessing CHLI. This parameter is equivalent to the Resilency parameter of 'p' as specified by MEF 10.2.1. jnxSoamLmCfgAvailabilityNumConsecutiveHighFlr must be strictly less than jnxSoamLmCfgAvailabilityNumConsecutiveIntervals. If not, the count of high loss intervals over time, jnxSoamLmAvailabilityHighLoss, and the count of consecutive high loss levels, jnxSoamLmAvailabilityConsecutiveHighLoss, is disabled. The number range of 1 through 10 must be supported. The number range of 1 through 1000 may be supported, but is not mandatory. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object contains the last measured results for a SOAM Loss Measurement session. Each row in the table represents a Loss Measurement session for the defined MEP. This table uses four indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific LM session on the selected MEP. Instances of this managed object are created automatically by the SNMP Agent when the Loss Measurement session is running. Each object in this table applies only if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable. The objects in this table do not need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamLmMeasuredStatsTable

OBJECT-TYPE

This object contains the last frame loss ratio in the forward direction calculated by this MEP. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the last frame loss ratio in the backward direction calculated by this MEP. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object indicates the availability status (the outcome of the last known availability indicator) in the forward direction. Note that the status of an availability indicator is not known until the loss for a number of subsequent availability indicators has been calculated (as determined by jnxSoamLmCfgAvailabilityNumConsecutiveIntervals)

OBJECT-TYPE

This object indicates the availability status (the outcome of the last availability indicator) in the backward direction. Note that the status of an availability indicator is not known until the loss for a number of subsequent availability indicators has been calculated (as determined by jnxSoamLmCfgAvailabilityNumConsecutiveIntervals)

OBJECT-TYPE

This object indicates the time of the last transition between available and unavailable in the forward direction. If there have been no transitions since the Loss Measurement Session was started, this is set to 0.

OBJECT-TYPE

This object indicates the time of the last transition between available and unavailable in the backward direction. If there have been no transitions since the Loss Measurement Session was started, this is set to 0.

OBJECT-TYPE

This table contains the results for the current Measurement Interval in a SOAM Loss Measurement session gathered during the interval indicated by iterator counts. A row in this table is created automatically by the SNMP Agent when the Loss Measurement session is configured. Each row in the table represents the current statistics for a Loss Measurement session for the defined MEP. This table uses four indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific LM session on the selected MEP. There may be more than one LM session per MEP. The main use case for this is to allow multiple CoS instances to be operating simultaneously for a MEP. The objects in this table apply regardless of the value of jnxSoamLmCfgType unless otherwise specified in the object description. Except for jnxSoamLmCurrentStatsIndex, jnxSoamLmCurrentStatsStartTime, jnxSoamLmCurrentStatsElapsedTime and jnxSoamLmCurrentStatsSuspect, each object in this table applies only if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable. The objects in this table do not need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamLmCurrentStatsTable

OBJECT-TYPE

The index for the current Measurement Interval for this PM session. This value will become the value for jnxSoamLmHistoryStatsIndex once the Measurement Interval is completed. Measurement Interval indexes are assigned sequentially by the SNMP Agent. The first Measurement Interval that occurs after the session is started is assigned index 1.

OBJECT-TYPE

The time that the current Measurement Interval started.

OBJECT-TYPE

The time that the current Measurement Interval has been running, in 0.01 seconds.

OBJECT-TYPE

Whether the Measurement Interval has been marked as suspect. The object is set to false at the start of a measurement interval. It is set to true when there is a discontinuity in the performance measurements during the Measurement Interval. Conditions for a discontinuity include, but are not limited to the following: 1 - The local time-of-day clock is adjusted by at least 10 seconds 2 - The conducting of a performance measurement is halted before the current Measurement Interval is completed 3 - A local test, failure, or reconfiguration that disrupts service

OBJECT-TYPE

This object contains the number of frames transmitted in the forward direction by this MEP. For a PM Session of types lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of type lmSlm this includes the count of SOAM ETH-SLM frames only.

OBJECT-TYPE

This object contains the number of frames received in the forward direction by this MEP. For a PM Session of types lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of types lmSlm this includes the count of SOAM ETH-SLM frames only.

OBJECT-TYPE

This object contains the minimum one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the maximum one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the average one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the number of frames transmitted in the backward direction by this MEP. For a PM Session of type lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of type lmSlm this includes the count of SOAM ETH-SLM frames only.

OBJECT-TYPE

This object contains the number of frames received in the backward direction by this MEP. For a PM Session of type lmLmm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of type lmSlm this includes the count of SOAM ETH-SLM frames only.

OBJECT-TYPE

This object contains the minimum one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the maximum one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the average one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the count of the number of SOAM PDUs sent during this Measurement Interval. This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames transmitted.

OBJECT-TYPE

This object contains the count of the number of SOAM PDUs PDUs received in this Measurement Interval. This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or lmCcm. This object indicates the number of LMR, CCM, or SLR SOAM frames received.

OBJECT-TYPE

This table contains the results for history Measurement Intervals in a SOAM Loss Measurement session. Rows of this table object are created automatically by the SNMP Agent when the Loss Measurement session is running and a Measurement Interval is completed. Each row in the table represents the history statistics for a Loss Measurement session Measurement Interval for the defined MEP. This table uses five indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific LM session on the selected MEP. The fifth index index the specific Measurement Interval. At least 32 completed Measurement Intervals are to be supported. 96 completed Measurement Intervals are recommended to be supported. If there are at least 32 rows in the table and a new Measurement Interval completes and a new row is to be added to the table, the oldest completed Measurement Interval may be deleted (row deletion). If the measurement interval is other than 15 minutes then a minimum of 8 hours of completed Measurement Intervals are to be supported and 24 hours are recommended to be supported. Except for jnxSoamLmHistoryStatsIndex, jnxSoamLmHistoryStatsEndTime, jnxSoamLmHistoryStatsElapsedTime and jnxSoamLmHistoryStatsSuspect, each object in this table applies only if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable. The rows and objects in this table are to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamLmHistoryStatsTable

OBJECT-TYPE

The index for the Measurement Interval within this PM session. Measurement Interval indexes are assigned sequentially by the SNMP Agent. The first Measurement Interval that occurs after the session is started is assigned index 1. Measurement Intervals for FLR (stored in this table) are based on iterator count and are indexed independently of Measurement Intervals for availability Referential integrity is necessary, i.e., the index needs to be persistent upon a reboot or restart of a device. The index is never reused while this session is active until it wraps to zero. The index value keeps increasing up to that time.

OBJECT-TYPE

The time that the Measurement Interval ended.

OBJECT-TYPE

The length of time that the Measurement Interval ran for, in 0.01 seconds.

OBJECT-TYPE

Whether the Measurement Interval has been marked as suspect. The object is set to true when there is a discontinuity in the performance measurements during the Measurement Interval. Conditions for a discontinuity include, but are not limited to the following: 1 - The local time-of-day clock is adjusted by at least 10 seconds 2 - The conducting of a performance measurement is halted before the current Measurement Interval is completed 3 - A local test, failure, or reconfiguration that disrupts service

OBJECT-TYPE

This object contains the number of frames transmitted in the forward direction by this MEP. For a PM Session of types lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of type lmSlm this includes the count of OAM ETH-SLM frames only.

OBJECT-TYPE

This object contains the number of frames received in the forward direction by this MEP. For a PM Session of types lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of type lmSlm this includes the count of OAM ETH-SLM frames only.

OBJECT-TYPE

This object contains the minimum one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the maximum one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the average one-way frame loss ratio in the forward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the number of frames transmitted in the backward direction by this MEP. For a PM Session of type lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of types lmSlm this includes the count of SOAM ETH-SLM frames only.

OBJECT-TYPE

This object contains the number of frames received in the backward direction by this MEP. For a PM Session of type lmLmm and lmCcm this includes Ethernet Service Frames and SOAM PDUs that are in a higher MEG level only. For a PM Session of types lmSlm this includes the count of SOAM ETH-SLM frames only.

OBJECT-TYPE

This object contains the minimum one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the maximum one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the average one-way frame loss ratio in the backward direction calculated by this MEP for this Measurement Interval. The FLR value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the count of the number of SOAM PDUs sent during this Measurement Interval. This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or lmCcm. It indicates the number of LMM, CCM, or SLM SOAM frames transmitted.

OBJECT-TYPE

This object contains the count of the number of SOAM PDUs received in this Measurement Interval. This object applies when jnxSoamLmCfgType is lmLmm, lmSlm, or lmCcm. This object indicates the number of LMR, CCM, or SLR SOAM frames received.

OBJECT-TYPE

This table contains the list of Loss Measurement configuration threshold values for LM Performance Monitoring. The main purpose of the threshold configuration table is to configure threshold alarm notifications indicating that a specific performance metric is not being met. Each row in the table represents a Loss Measurement session threshold set for the defined MEP. This table uses five indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific LM session on the selected MEP. The fifth index is the specific threshold set number. Rows in this table are not created automatically. A row is created in this table to set up a threshold set on a configured MEP that has a configured LM session. If two managers try to 'create' the same row at the same time, the first creation would succeed, the second creation attempt would result in an error. The second creation attempt would then need to select a new index value to successfully create a new row. An NE needs to support at least one threshold set for NE SOAM PM compliance. A second threshold set on the NE is desirable. More than two threshold sets can be configured on the NE if supported on the NE. All the objects in the row have a default value that disables the particular threshold measurement. In order to enable a threshold measurement the particular bit in the jnxSoamLmThresholdCfgEnable object is to be set to '1' and the selected threshold measurement is to have a threshold value configured. Non-configured threshold measurements are disabled by default. The writable objects in this table need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamLmThresholdCfgTable.

OBJECT-TYPE

The index of the threshold number for the specific LM threshold entry. An index value of '1' needs to be supported. Other index values can also be supported.

OBJECT-TYPE

A vector of bits that indicates the type of SOAM LM thresholds notifications that are enabled. A bit set to '1' enables the specific SOAM LM threshold notification and when the specific counter is enabled and the threshold is crossed a notification is generated. A bit set to '0' disables the specific SOAM LM threshold notification. If a particular SOAM LM threshold is not supported the BIT value is set to '0'. bJnxSoamLmMeasuredFlrForwardThreshold(0) Enables/disables measured frame loss forward ratio threshold notification. The notification is sent immediately when the jnxSoamLmMeasuredStatsForwardFlr value is greater than or equal to the threshold value. bJnxSoamLmMaxFlrForwardThreshold(1) Enables/disables maximum frame loss forward ratio threshold notification. The notification is sent immediately when the jnxSoamLmCurrentStatsForwardMaxFlr value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamLmAvgFlrForwardThreshold(2) Enables/disables average frame loss forward ratio threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamLmCurrentStatsForwardAvgFlr value is greater than or equal to the threshold value. bJnxSoamLmMeasuredFlrBackwardThreshold(3) Enables/disables measured frame loss backward ratio threshold notification. The notification is sent immediately when the jnxSoamLmMeasuredStatsBackwardFlr value is greater than or equal to the threshold value. bJnxSoamLmMaxFlrBackwardThreshold(4) Enables/disables maximum frame loss backward ratio threshold notification. The notification is sent immediately when the jnxSoamLmCurrentStatsBackwardMaxFlr value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamLmAvgFlrBackwardThreshold(5) Enables/disables average frame loss backward ratio threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamLmCurrentStatsBackwardAvgFlr value is greater than or equal to the threshold value.

OBJECT-TYPE

This object is used to set the average forward frame loss ratio threshold value that will be used to determine if a threshold notification is generated.

OBJECT-TYPE

This object is used to set the average backward frame loss ratio threshold value that will be used to determine if a threshold notification is generated.

OBJECT-TYPE

The status of the row. The writable columns in a row cannot be changed if the row is active. All columns are to have a valid value before a row can be activated.

OBJECT-TYPE

This object contains the current results for a SOAM Loss Measurement session for availability statistics gathered during the interval indicated by jnxSoamLmCfgAvailabilityMeasurementInterval. Each row in the table represents a Loss Measurement session for the defined MEP. This table uses four indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific LM session on the selected MEP. Instances of this managed object are created automatically by the SNMP Agent when the Loss Measurement session is running. The objects in this table apply regardless of the value of jnxSoamLmCfgType unless otherwise specified in the object description. Except for jnxSoamLmCurrentAvailStatsIndex, jnxSoamLmCurrentAvailStatsStartTime, jnxSoamLmCurrentAvailStatsElapsedTime and jnxSoamLmCurrentAvailStatsSuspect, each object in this table applies only if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable. The objects in this table may be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamLmCurrentAvailStatsTable

OBJECT-TYPE

The index for the current availability Measurement Interval for this PM session. This value will become the value for jnxSoamLmHistoryAvailStatsIndex once the Measurement Interval is completed. The duration of the Measurement Interval is specified by jnxSoamLmCfgAvailabilityMeasurementInterval. Measurement Interval indexes are assigned sequentially by the SNMP Agent. The first Measurement Interval that occurs after the session is started is assigned index 1.

OBJECT-TYPE

The time that the current Measurement Interval started.

OBJECT-TYPE

The time that the current Measurement Interval has been running, in 0.01 seconds.

OBJECT-TYPE

Whether the Measurement Interval has been marked as suspect. The object is set to false at the start of a measurement interval. It is set to true when there is a discontinuity in the performance measurements during the Measurement Interval. Conditions for a discontinuity include, but are not limited to the following: 1 - The local time-of-day clock is adjusted by at least 10 seconds 2 - The conducting of a performance measurement is halted before the current Measurement Interval is completed 3 - A local test, failure, or reconfiguration that disrupts service

OBJECT-TYPE

This object is the number of high loss intervals (HLI) over time in the forward direction. The value starts at 0 and increments for every HLI that occurs. This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.

OBJECT-TYPE

This object is the number of high loss intervals (HLI) over time in the backwards direction. The value starts at 0 and increments for every HLI that occurs. This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.

OBJECT-TYPE

This object is the number of consecutive high loss intervals (CHLI) over time in the forward direction. The value starts at 0 and increments for every HLI that occurs that is determined to fall within a CHLI. This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.

OBJECT-TYPE

This object is the number of consecutive high loss intervals (CHLI) over time in the backward direction. The value starts at 0 and increments for every HLI that occurs that is determined to fall within a CHLI. This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.

OBJECT-TYPE

This object contains the number of availability indicators evaluated as available in the forward direction by this MEP during this Measurement Interval.

OBJECT-TYPE

This object contains the number of availability indicators evaluated as available in the backward direction by this MEP during this Measurement Interval.

OBJECT-TYPE

This object contains the number of availability indicators evaluated as unavailable in the forward direction by this MEP during this Measurement Interval.

OBJECT-TYPE

This object contains the number of availability indicators evaluated as unavailable in the backward direction by this MEP during this Measurement Interval.

OBJECT-TYPE

This object contains the minimum one-way availability flr in the forward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 2626 0.001 percent.

OBJECT-TYPE

This object contains the maximum one-way availability flr in the forward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the average one-way availability flr in the forward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the minimum one-way availability flr in the backward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the maximum one-way availability flr in the backward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the average one-way availability flr in the backward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This table contains the results for availability history Measurement Intervals in a SOAM Loss Measurement session. Rows of this table object are created automatically by the SNMP Agent when the Loss Measurement session is running and a Measurement Interval is completed. Each row in the table represents the history statistics for a Loss Measurement session availability Measurement Interval for the defined MEP. This table uses five indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific LM session on the selected MEP. The fifth index index the specific Measurement Interval. At least 32 completed Measurement Intervals are to be supported. 96 completed Measurement Intervals are recommended to be supported. If there are at least 32 rows in the table and a new Measurement Interval completes and a new row is to be added to the table, the oldest completed Measurement Interval can be deleted (row deletion). If the availability Measurement Interval is other than 15 minutes then a minimum of 8 hours of completed Measurement Intervals are to be supported and 24 hours are recommended to be supported. Except for jnxSoamLmHistoryAvailStatsIndex, jnxSoamLmHistoryAvailStatsEndTime, jnxSoamLmHistoryAvailStatsElapsedTime and jnxSoamLmHistoryAvailStatsSuspect, each object in this table applies only if the corresponding bit is set in jnxSoamLmCfgMeasurementEnable. The rows and objects in this table are to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamLmHistoryAvailStatsTable

OBJECT-TYPE

The index for the availability Measurement Interval within this PM session. Measurement Interval indexes are assigned sequentially by the SNMP Agent. The first Measurement Interval that occurs after the session is started is assigned index 1. Measurement Intervals for availability (stored in this table) are based on jnxSoamLmCfgAvailabilityMeasurementInterval and are indexed independently of Measurement Intervals for FLR (stored in jnxSoamLmHistoryStatsTable). Referential integrity is necessary, i.e., the index needs to be persistent upon a reboot or restart of a device. The index is never reused while this session is active until it wraps to zero. The index value keeps increasing up to that time.

OBJECT-TYPE

The time that the Measurement Interval ended.

OBJECT-TYPE

The length of time that the Measurement Interval ran for, in 0.01 seconds.

OBJECT-TYPE

Whether the Measurement Interval has been marked as suspect. The object is set to true when there is a discontinuity in the performance measurements during the Measurement Interval. Conditions for a discontinuity include, but are not limited to the following: 1 - The local time-of-day clock is adjusted by at least 10 seconds 2 - The conducting of a performance measurement is halted before the current Measurement Interval is completed 3 - A local test, failure, or reconfiguration that disrupts service

OBJECT-TYPE

This object is the number of high loss intervals (HLI) over time in the forward direction. The value starts at 0 and increments for every HLI that occurs. This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.

OBJECT-TYPE

This object is the number of high loss intervals (HLI) over time in the backward direction. The value starts at 0 and increments for every HLI that occurs. This parameter is equivalent to 'L Sub T' found in MEF 10.2.1.

OBJECT-TYPE

This object is the number of consecutive high loss intervals (CHLI) over time in the forward direction. The value starts at 0 and increments for every HLI that occurs that is determined to fall within a CHLI. This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.

OBJECT-TYPE

This object is the number of consecutive high loss intervals (CHLI) over time in the forward direction. The value starts at 0 and increments for every HLI that occurs that is determined to fall within a CHLI. This parameter is equivalent to 'B Sub T' found in MEF 10.2.1.

OBJECT-TYPE

This object contains the number of availability indicators evaluated as available in the forward direction by this MEP during this Measurement Interval.

OBJECT-TYPE

This object contains the number of availability indicators evaluated as available in the backward direction by this MEP during this Measurement Interval.

OBJECT-TYPE

This object contains the number of availability indicators evaluated as unavailable in the forward direction by this MEP during this Measurement Interval.

OBJECT-TYPE

This object contains the number of availability indicators evaluated as unavailable in the backward direction by this MEP during this Measurement Interval.

OBJECT-TYPE

This object contains the minimum one-way availability flr in the forward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the maximum one-way availability flr in the forward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the average one-way availability flr in the forward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the minimum one-way availability flr in the backward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the maximum one-way availability flr in the backward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 0.001 percent.

OBJECT-TYPE

This object contains the average one-way availability flr in the backward direction, from among the set of availability flr values calculated by the MEP in this Measurement Interval. There is one availability flr value for each 'delta_t' time period within the Measurement Interval, as specified in MEF 10.2.1. The flr value is a ratio that is expressed as a percent with a value of 0 (ratio 0.00) through 100000 (ratio 1.00). Units are in milli-percent, where 1 indicates 3458 0.001 percent.

OBJECT-IDENTITY

OBJECT-TYPE

This table includes configuration objects and operations for the Delay Measurement function. Each row in the table represents a Delay Measurement session for the defined MEP. This table uses four indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific DM session on the selected MEP. A Delay Measurement session is created on an existing MEP by first accessing the jnxSoamDmOperNextIndex object and using this value as the jnxSoamDmCfgIndex in the row creation. Some writable objects in this table are only applicable in certain cases (as described under each object), and attempts to write values for them in other cases will be ignored. The writable objects in this table need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamDmCfgTable.

OBJECT-TYPE

An index to the Delay Measurement Configuration table which indicates the specific measurement session for the MEP. jnxSoamPmMepOperNextIndex needs to be inspected to find an available index for row-creation. Referential integrity is necessary, i.e., the index needs to be persistent upon a reboot or restart of a device. The index is never reused for other PM sessions on the same MEP while this session is active. The index value keeps increasing until it wraps to zero. This is to facilitate access control based on a fixed index for an EMS, since the index is not reused.

OBJECT-TYPE

This object indicates what type of Delay Measurement is to be performed. dmDmm(1) DMM SOAM PDU generated, DMR responses received (one-way or two-way measurements) dm1DmTx(2) 1DM SOAM PDU generated (one-way measurements are made by the receiver) dm1DmRx(3) 1DM SOAM PDU received and tracked (one-way measurements) The exact PDUs to use are specified by this object in combination with jnxSoamDmCfgVersion. The value dmDMM is required. The values dm1DmTx and dm1DmRx are optional. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object indicates the version of the PDUs used to perform Delay Measurement. Version 0 indicates the PDU formats defined in Y.1731-2008. Version 1 indicates the PDU formats defined in Y.1731-2011. The exact PDUs to use are specified by this object in combination with jnxSoamDmCfgType. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies whether the Delay Measurement session is enabled. The value 'true' indicates the Delay Measurement session is enabled AND SOAM PDUs are sent and/or measurements are collected when the session is running according to the scheduling objects (start time, stop time, etc.). The value 'false' indicates the Delay Measurement session is disabled AND SOAM PDUs are not sent and/or measurements collected. For a Delay Measurement session to be removed the row is deleted in order to release internal resources. This object can written/modified after row creation time. If the DM session is enabled it resumes after shutdown/restart. If the DM session is disabled the current Measurement Interval is stopped, if it in process at the time, and all the in process calculations for the partially completed Measurement Interval are finalized. This object does not affect whether the single-ended Responder is enabled or not, which is enabled or disabled by the jnxSoamPmMepDmSingleEndedResponder object.

OBJECT-TYPE

A vector of bits that indicates the type of SOAM DM counters that are enabled. A bit set to '1' enables the specific SOAM DM counter. A bit set to '0' disables the SOAM DM counter. If a particular SOAM DM counter is not supported the BIT value is set to '0'. Not all SOAM DM counters are supported for all SOAM DM types. This object can only be written at row creation time and cannot be modified once it has been created. bSoamPdusSent(0) Enables/disables the jnxSoamDmCurrentStatsSoamPdusSent and jnxSoamDmHistoryStatsSoamPdusSent counters. bSoamPdusReceived(1) Enables/disables the jnxSoamDmCurrentStatsSoamPdusReceived and jnxSoamDmHistoryStatsSoamPdusReceived counters. bFrameDelayTwoWayBins(2) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'twoWayFrameDelay'. bFrameDelayTwoWayMin(3) Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayMin and jnxSoamDmHistoryStatsFrameDelayTwoWayMin counters. bFrameDelayTwoWayMax(4) Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayMax and jnxSoamDmHistoryStatsFrameDelayTwoWayMax counters. bFrameDelayTwoWayAvg(5) Enables/disables the jnxSoamDmCurrentStatsFrameDelayTwoWayAvg and jnxSoamDmHistoryStatsFrameDelayTwoWayAvg counters. bFrameDelayForwardBins(6) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'forwardFrameDelay'. bFrameDelayForwardMin(7) Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardMin and jnxSoamDmHistoryStatsFrameDelayForwardMin counters. bFrameDelayForwardMax(8) Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardMax and jnxSoamDmHistoryStatsFrameDelayForwardMax counters. bFrameDelayForwardAvg(9) Enables/disables the jnxSoamDmCurrentStatsFrameDelayForwardAvg and jnxSoamDmHistoryStatsFrameDelayForwardAvg counters. bFrameDelayBackwardBins(10) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'backwardFrameDelay'. bFrameDelayBackwardMin(11) Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardMin and jnxSoamDmHistoryStatsFrameDelayBackwardMin counters. bFrameDelayBackwardMax(12) Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardMax and jnxSoamDmHistoryStatsFrameDelayBackwardMax counters. bFrameDelayBackwardAvg(13) Enables/disables the jnxSoamDmCurrentStatsFrameDelayBackwardAvg and jnxSoamDmHistoryStatsFrameDelayBackwardAvg counters. bIfdvForwardBins(14) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'forwardIfdv'. bIfdvForwardMin(15) Enables/disables the jnxSoamDmCurrentStatsIfdvForwardMin and jnxSoamDmHistoryStatsIfdvForwardMin counters. bIfdvForwardMax(16) Enables/disables the jnxSoamDmCurrentStatsIfdvForwardMax and jnxSoamDmHistoryStatsIfdvForwardMax counters. bIfdvForwardAvg(17) Enables/disables the jnxSoamDmCurrentStatsIfdvForwardAvg and jnxSoamDmHistoryStatsIfdvForwardAvg counters. bIfdvBackwardBins(18) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'backwardIfdv'. bIfdvBackwardMin(19) Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardMin and jnxSoamDmHistoryStatsIfdvBackwardMin counters. bIfdvBackwardMax(20) Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardMax and jnxSoamDmHistoryStatsIfdvBackwardMax counters. bIfdvBackwardAvg(21) Enables/disables the jnxSoamDmCurrentStatsIfdvBackwardAvg and jnxSoamDmHistoryStatsIfdvBackwardAvg counters. bIfdvTwoWayBins(22) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'twoWayIfdv'. bIfdvTwoWayMin(23) Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayMin and jnxSoamDmHistoryStatsIfdvTwoWayMin counters. bIfdvTwoWayMax(24) Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayMax and jnxSoamDmHistoryStatsIfdvTwoWayMax counters. bIfdvTwoWayAvg(25) Enables/disables the jnxSoamDmCurrentStatsIfdvTwoWayAvg and jnxSoamDmHistoryStatsIfdvTwoWayAvg counters. bFrameDelayRangeForwardBins(26) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'forwardFrameDelayRange'. bFrameDelayRangeForwardMax(27) Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeForwardMax and jnxSoamDmHistoryStatsFrameDelayRangeForwardMax counters. bFrameDelayRangeForwardAvg(28) Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg and jnxSoamDmHistoryStatsFrameDelayRangeForwardAvg counters. bFrameDelayRangeBackwardBins(29) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'backwardFrameDelayRange'. bFrameDelayRangeBackwardMax(30) Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax and jnxSoamDmHistoryStatsFrameDelayRangeBackwardMax counters. bFrameDelayRangeBackwardAvg(31) Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg and jnxSoamDmHistoryStatsFrameDelayRangeBackwardAvg counters. bFrameDelayRangeTwoWayBins(32) Enables/disables the jnxSoamDmCurrentStatsBinsEntry counter and the jnxSoamDmHistoryStatsBinsEntry counter when the jnxSoamDmCfgMeasBinType is 'twoWayFrameDelayRange'. bFrameDelayRangeTwoWayMax(33) Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax and jnxSoamDmHistoryStatsFrameDelayRangeTwoWayMax counters. bFrameDelayRangeTwoWayAvg(34) Enables/disables the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg and jnxSoamDmHistoryStatsFrameDelayRangeTwoWayAvg counters. bMeasuredStatsFrameDelayTwoWay(35) Enables/disables the jnxSoamDmMeasuredStatsFrameDelayTwoWay counter. bMeasuredStatsFrameDelayForward(36) Enables/disables the jnxSoamDmMeasuredStatsFrameDelayForward counter. bMeasuredStatsFrameDelayBackward(37) Enables/disables the jnxSoamDmMeasuredStatsFrameDelayBackward counter. bMeasuredStatsIfdvTwoWay(38) Enables/disables the jnxSoamDmMeasuredStatsIfdvTwoWay counter. bMeasuredStatsIfdvForward(39) Enables/disables the jnxSoamDmMeasuredStatsIfdvForward counter. bMeasuredStatsIfdvBackward(40) Enables/disables the jnxSoamDmMeasuredStatsIfdvBackward counter.

OBJECT-TYPE

This object specifies the interval between Delay Measurement OAM message transmission. For Delay Measurement monitoring applications, the default value is 100ms. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the priority of frames with Delay Measurement OAM message information. The default value is to be the value which yields the lowest frame loss. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the Delay Measurement frame size between 64 bytes and the maximum transmission unit of the EVC. The range of frame sizes from 64 through 2000 octets need to be supported, and the range of frame sizes from 2001 through 9600 octets is suggested to be supported. The adjustment to the frame size of the standard frame size is accomplished by the addition of a Data or Test TLV. A Data or Test TLV is only added to the frame if the frame size is greater than 64 bytes. This object is only valid for the entity transmitting the Delay Measurement frames (dmDmm, dm1DmTx) and is ignored by the entity receiving frames. In addition, this object is not valid when jnxSoamDmCfgVersion is 0. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the DM data pattern included in a Data TLV when the size of the DM frame is determined by the jnxSoamDmFrameSize object and jnxSoamDmTestTlvIncluded is 'false'. If the frame size object does not define the DM frame size or jnxSoamDmTestTlvIncluded is 'true' the value of this object is ignored. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

Indicates whether a Test TLV or Data TLV is included when the size of the DM frame is determined by the jnxSoamDmFrameSize object. A value of 'true' indicates that the Test TLV is to be included. A value of 'false' indicates that the Data TLV is to be included. If the frame size object does not define the DM frame size the value of this object is ignored. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the type of test pattern to be sent in the DM frame Test TLV when the size of DM PDU is determined by the jnxSoamDmFrameSize object and jnxSoamDmTestTlvIncluded is 'true'. If the frame size object does not define the DM frame size or jnxSoamDmTestTlvIncluded is 'false' the value of this object is ignored. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the number of completed Measurement Intervals to store in the history statistic table. At least 32 completed Measurement Intervals are to be stored. 96 Measurement Intervals are recommended to be stored. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

The Maintenance Association End Point Identifier of another MEP in the same Maintenance Association to which the SOAM DM frame is to be sent. This address will be used if the value of the column jnxSoamDmDestIsMepId is 'true'. A value of zero means that the destination MEP ID has not been configured. This object is only valid for the entity transmitting the Delay Measurement frames, types 'dmDmm' and 'dm1DmTx'. It is not applicable for the 'dm1DmRx' type. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

A value of 'true' indicates that MEPID of the target MEP is used for SOAM DM frame transmission. A value of 'false' indicates that the destination MAC address of the target MEP is used for SOAM DM frame transmission. This object is only valid for the entity transmitting the Delay Measurement frames, types 'dmDmm' and 'dm1DmTx'. It is not applicable for the 'dm1DmRx type. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the type of start time of the SOAM DM session. The start time can be disabled (none), immediate, relative, or fixed. The value of 'none' is illegal and a write error will be returned if this value is used. The value of 'immediate' starts the SOAM DM session when the jnxSoamDmCfgEnabled is true. The value of 'fixed' starts the SOAM DM session when the jnxSoamDmFixedStartDateAndTime is less than or equal to the current system date and time and jnxSoamDmCfgEnabled is true. This value is used to implement an On-Demand fixed time PM session. The value of 'relative' starts the SOAM DM session when the current system date and time minus the jnxSoamDmRelativeStartTime is greater than or equal to the system date and time when the jnxSoamDmStartTimeType object was written and jnxSoamDmCfgEnabled is true. This value is used to implement an On-Demand relative time PM session. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies a configurable repetition time between Measurement Intervals in a Delay Measurement session in seconds. If the value is 0 (none), there is no time gap between the end of one Measurement Interval and the start of a new Measurement Interval. This is the normal usage case. If the value is greater than one Measurement Interval there is time gap between the end of one Measurement Interval and the start of the next Measurement Interval. The repetition time specifies the time between the start of consecutive Measurement Intervals; hence the gap between the end of one Measurement Interval and the start of the next is equal to the difference between the repetition time and the measurement interval. During this gap, no SOAM PDUs are sent for this session and no measurements are made. If the value is greater 0 but less than or equal to the measurement interval, an error is returned. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies whether the Measurement Intervals for the Delay Measurement session are aligned with a zero offset to real time. The value 'true' indicates that each Measurement Interval starts at a time which is aligned to NE time source hour, if the repetition time (or the Measurement Interval, if the repetition time is 0) is a factor of an hour, i.e. 60min/15min = 4. For instance, a Measurement Interval/Repetition Time of 15 minutes would stop/start the Measurement Interval at 0, 15, 30, and 45 minutes of an hour. A Measurement Interval/Repetition Time of 7 minutes would not align to the hour since 7 minutes is NOT a factor of an hour, i.e. 60min/7min = 8.6. In this case the behavior is the same as if the object is set to 'false'. The value 'false' indicates that the first Measurement Interval starts at an arbitrary time and each subsequent Measurement Interval starts at a time which is determined by jnxSoamLmCfgRepetitionTime. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the selection offset for Inter-Frame Delay Variation measurements. If this value is set to n, then the IFDV is calculated by taking the difference in frame delay between frame F and frame (F+n). This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object indicates whether the current session is defined to be 'Proactive' or 'On-Demand'. A value of 'proactive' indicates the current session is 'Proactive'. A value of 'onDemand' indicates the current session is 'On-Demand'. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object indicates the current status of the DM session. A value of 'active' indicates the current DM session is active, i.e. the current time lies between the start time and the stop time, and jnxSoamDmCfgEnabled is true. A value of 'notActive' indicates the current DM session is not active, i.e. it has not started yet, has stopped upon reaching the stop time, or is disabled.

OBJECT-TYPE

This object when written clears the Delay Measurement history tables (jnxSoamDmHistoryStatsTable) - all rows are deleted. When read the value always returns 'false'. Writing this value does not change the current stat table, nor any of the items in the configuration table. Writing this object at row creation has no effect.

OBJECT-TYPE

The status of the row. The writable columns in a row cannot be changed if the row is active, except for jnxSoamDmCfgEnabled and jnxSoamDmCfgHistoryClear objects. All columns are to have a valid value before a row can be activated.

OBJECT-TYPE

This object specifies a Measurement Interval in minutes. A Measurement Interval 15 minutes needs to be supported, other intervals may be supported. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

The Target or Destination MAC Address Field to be transmitted. If mefSoamDmCfgType is 'dmDmm', the destination address is to be the unicast address of the destination MEP. An error is returned if this object is set to a multicast address. If mefSoamDmCfgType is 'dm1DmTx', the destination address is normally the unicast address of the destination MEP, but can be a multicast address indicating the level of the MEG: 01-80-c2-00-00-3y, where y is the level of the MEG. An error is returned if this object is set to any other multicast address. If mefSoamDmCfgType is 'dm1DmRx', this object is ignored. This address will be used if the value of the object mefSoamDmDestIsMepId is 'false'. This object is only valid for the entity transmitting the SOAM DM frames and is ignored by the entity receiving SOAM DM frames. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

The Source MAC Address Field of the received SOAM DM session PDUs. If mefSoamDmCfgType is dm1DmRx this object indicates the source address of the dm1DmTx DM session. This object is only valid for mefSoamDmCfgType set to dm1DmRx. It is ignored for mefSoamDmCfgType set to dmDmm or dm1DmTx. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the fixed start date/time for the SOAM Delay Measurement session. This object is used only used if mefSoamDmStartTimeType is 'fixed' and is ignored otherwise. The default value is year 0000, month 01, day 01, time 00:00:00.00. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the relative start time, from the current system time, for the SOAM DM session. This object is used only if mefSoamDmStartTimeType is 'relative' and is ignored otherwise. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the type of stop time to terminate the SOAM DM session. The stop time can be forever (none), relative, or fixed. The value of 'none' indicates that the SOAM DM session never ends once it has started unless the session is disabled. The value of 'immediate' is illegal and a write error will be returned if this value is used. The value of 'fixed' stops the SOAM DM session when the mefSoamDmFixedStopDateAndTime is less than or equal to the current system date. This value is used to implement an On-Demand fixed time PM session. The value of 'relative' stops the SOAM DM session when the time indicated by mefSoamDmRelativeStopTime has passed since the session start time as determined by the mefSoamDmCfgStartTimeType, mefSoamDmCfgFixedStartDateAndTime and mefSoamDmCfgRelativeStartTime objects. This value is used to implement an On-Demand relative time PM session. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the fixed stop date/time for the SOAM Delay Measurement session. This object is used only used if mefSoamDmStopTimeType is 'fixed' and is ignored otherwise. The default value is year 0000, month 01, day 01, time 00:00:00.00. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the relative stop time, from the session start time, to stop the SOAM DM session. This object is used only if mefSoamDmStopTimeType is 'relative' and is otherwise. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the offset in minutes from the time of day value if mefSoamDmCfgAlignMeasurementIntervals is 'true' and the repetition time is a factor of 60 minutes. If not, the value of this object is ignored. If the Measurement Interval is 15 minutes and mefSoamDmCfgAlignMeasurementIntervals is true and if this object was set to 5 minutes, the Measurement Intervals would start at 5, 20, 35, 50 minutes past each hour. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the number of measurement bins per Measurement Interval for Frame Delay measurements. At least 3 bins are to be supported; at least 10 bins are recommended to be supported. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the number of measurement bins per Measurement Interval for Inter-Frame Delay Variation measurements. The minimum number of measurement bins to be supported is 2. The supported is 10. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object specifies the number of measurement bins per Measurement Interval for Frame Delay Range measurements. At least 2 bins are to be supported; at least 10 bins are recommended to be supported. This object can only be written at row creation time and cannot be modified once it has been created.

OBJECT-TYPE

This object contains the last measured results for a SOAM Delay Measurement session. Each row in the table represents a Delay Measurement session for the defined MEP. This table uses four indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific DM session on the selected MEP. Instances of this managed object are created automatically by the SNMP Agent when the Delay Measurement session is running. Each object in this table applies only if the corresponding bit is set in jnxSoamDmCfgMeasurementEnable. The objects in this table do not need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamDmMeasuredStatsTable

OBJECT-TYPE

This object contains the two-way frame delay calculated by this MEP from the last received SOAM PDU. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the frame delay in the forward direction calculated by this MEP from the last received SOAM PDU. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the frame delay in the backward direction calculated by this MEP from the last received SOAM PDU. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the last two-way inter-frame delay interval calculated by this MEP. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the last one-way inter-frame delay interval in the forward direction calculated by this MEP. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the last one-way inter-frame delay interval in the backward direction calculated by this MEP. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This table contains the results for the current Measurement Interval in a SOAM Delay Measurement session gathered during the interval indicated by iterator count. A row in this table is created automatically by the SNMP Agent when the Delay Measurement session is configured. Each row in the table represents the current statistics for a Delay Measurement session for the defined MEP. This table uses four indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific DM session on the selected MEP. There can be more than one DM session per MEP. The objects in this table apply regardless of the value of jnxSoamDmCfgType unless otherwise specified in the object description. Backward and two-way statistic objects are undefined if jnxSoamDmCfgType is dm1DmRx. Except for jnxSoamDmCurrentStatsIndex, jnxSoamDmCurrentStatsStartTime jnxSoamDmCurrentStatsElapsedTime and jnxSoamDmCurrentStatsSuspect, each object in this table applies only if the corresponding bit is set in jnxSoamDmCfgMeasurementEnable. The objects in this table do not need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamDmCurrentStatsTable

OBJECT-TYPE

The index for the current Measurement Interval for this PM session. This value will become the value for jnxSoamDmHistoryStatsIndex once the Measurement Interval is completed. Measurement Interval indexes are assigned sequentially by the SNMP Agent. The first Measurement Interval that occurs after the session is started is assigned index 1.

OBJECT-TYPE

The time that the current Measurement Interval started.

OBJECT-TYPE

The time that the current Measurement Interval has been running, in 0.01 seconds.

OBJECT-TYPE

Whether the Measurement Interval has been marked as suspect. The object is to be set to false at the start of a measurement interval. It is set to true when there is a discontinuity in the performance measurements during the Measurement Interval. Conditions for a discontinuity include, but are not limited to the following: 1 - The local time-of-day clock is adjusted by at least 10 seconds 2 - The conducting of a performance measurement is halted before the current Measurement Interval is completed 3 - A local test, failure, or reconfiguration that disrupts service

OBJECT-TYPE

This object contains the minimum two-way frame delay calculated by this MEP for this Measurement Interval. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum two-way frame delay calculated by this MEP for this Measurement Interval. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average two-way frame delay calculated by this MEP for this Measurement Interval. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the minimum one-way frame delay in the forward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the maximum one-way frame delay in the forward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the average one-way frame delay in the forward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the minimum one-way frame delay in the backward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum one-way frame delay in the backward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average one-way frame delay in the backward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the minimum one-way inter-frame delay interval in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the maximum one-way inter-frame delay interval in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the average one-way inter-frame delay interval in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the minimum one-way inter-frame delay interval in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum one-way inter-frame delay interval in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average one-way inter-frame delay interval in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the minimum two-way inter-frame delay interval calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum two-way inter-frame delay interval calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average two-way inter-frame delay interval calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the count of the number of SOAM PDUs sent during this Measurement Interval. This object applies when jnxSoamDmCfgType is dmDmm or dm1DmTx and is undefined if jnxSoamDmCfgType is dm1DmRx. It indicates the number of DMM or 1DM SOAM frames transmitted.

OBJECT-TYPE

This object contains the count of the number of SOAM PDUs received in this Measurement Interval. This object indicates the number of DMR and 1DM SOAM frames received. This object applies when jnxSoamDmCfgTypeis dmDmm or dm1DmRx and is undefined if jnxSoamDmCfgTypeis dm1DmTx.

OBJECT-TYPE

This object contains the maximum one-way frame delay range in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the average one-way frame delay range in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the maximum one-way frame delay range in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average one-way frame delay range in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum two-way frame delay range calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average two-way frame delay range calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This table contains the results for history Measurement Intervals in a SOAM Delay Measurement session. Rows of this table are created automatically by the SNMP Agent when the Delay Measurement session is running and a Measurement Interval is completed. Each row in the table represents the Measurement Interval history statistics for a Delay Measurement session for the defined MEP. This table uses five indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific DM session on the selected MEP. The fifth index is the Measurement Interval. At least 32 completed Measurement Intervals are to be supported. 96 completed Measurement Intervals are recommended to be supported. If there are at least 32 rows in the table and a new Measurement Interval completes and a new row is to be added to the table, the oldest completed Measurement Interval can be deleted (row deletion). If the measurement interval is other than 15 minutes then a minimum of 8 hours of completed Measurement Intervals are to be supported and 24 hours are recommended to be supported. The objects in this table apply regardless of the value of jnxSoamDmCfgType unless otherwise specified in the object description. Backward and two-way statistic objects are undefined if jnxSoamDmCfgType is dm1DmRx. Except for jnxSoamDmHistoryStatsIndex, jnxSoamDmHistoryStatsEndTime, jnxSoamDmHistoryStatsElapsedTime and jnxSoamDmHistoryStatsSuspect, each object in this table applies only if the corresponding bit is set in jnxSoamDmCfgMeasurementEnable. The rows and objects in this table are to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamDmHistoryStatsTable

OBJECT-TYPE

The index for the Measurement Interval within this PM session. Measurement Interval indexes are assigned sequentially by the SNMP Agent. The first Measurement Interval that occurs after the session is started is assigned index 1. Referential integrity is necessary, i.e., the index needs to be persistent upon a reboot or restart of a device. The index is never reused while this session is active until it wraps to zero. The index value keeps increasing up to that time.

OBJECT-TYPE

The time that the Measurement Interval ended.

OBJECT-TYPE

The length of time that the Measurement Interval ran for, in 0.01 seconds.

OBJECT-TYPE

Whether the Measurement Interval has been marked as suspect. The object is set to true when there is a discontinuity in the performance measurements during the Measurement Interval. Conditions for a discontinuity include, but are not limited to the following: 1 - The local time-of-day clock is adjusted by at least 10 seconds 2 - The conducting of a performance measurement is halted before the current Measurement Interval is completed 3 - A local test, failure, or reconfiguration that disrupts service

OBJECT-TYPE

This object contains the minimum two-way frame delay calculated by this MEP for this Measurement Interval. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum two-way frame delay calculated by this MEP for this Measurement Interval. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average two-way frame delay calculated by this MEP for this Measurement Interval. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the minimum one-way frame delay in the forward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the maximum one-way frame delay in the forward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the average one-way frame delay in the forward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the minimum one-way frame delay in the backward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum one-way frame delay in the backward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average one-way frame delay in the backward direction calculated by this MEP for this Measurement Interval. The value of this object may not be accurate in the absence of sufficiently precise clock synchronization. This object is undefined is jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the minimum one-way inter-frame delay interval in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the maximum one-way inter-frame delay interval in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the average one-way inter-frame delay interval in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the minimum one-way inter-frame delay interval in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum one-way inter-frame delay interval in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average one-way inter-frame delay interval in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the minimum two-way inter-frame delay interval calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum two-way inter-frame delay interval calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average two-way inter-frame delay interval calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the count of the number of SOAM PDUs sent during this Measurement Interval. This object applies when jnxSoamDmCfgType is dmDmm or dm1DmTx and is undefined if jnxSoamDmCfgType is dm1DmRx. It indicates the number of DMM or 1DM SOAM frames transmitted.

OBJECT-TYPE

This object contains the count of the number of SOAM PDUs received in this Measurement Interval. This object indicates the number of DMR and 1DM SOAM frames received. This object applies when jnxSoamDmCfgType is dmDmm or dm1DmRx and is undefined if jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the maximum one-way Frame Delay Range in the forward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the average one-way Frame Delay Range in the forward direction calculated by this MEP for this Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx.

OBJECT-TYPE

This object contains the maximum one-way Frame Delay Range in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average one-way Frame Delay Range in the backward direction calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the maximum two-way Frame Delay Range calculated by this MEP for this Measurement Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This object contains the average two-way Frame Delay Range Interval. The value of this object is undefined when jnxSoamDmCfgType is dm1DmTx or dm1DmRx.

OBJECT-TYPE

This table contains the list of Delay Measurement threshold configuration values for DM Performance Monitoring. The main purpose of the threshold configuration table is to configure threshold alarm notifications indicating that a specific performance metric is not being met. Each row in the table represents a Delay Measurement session threshold set for the defined MEP. This table uses five indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific DM session on the selected MEP. The fifth index is the specific threshold set number. Rows in this table are not created automatically. A row is created in this table to set up a threshold set on a configured MEP that has a configured DM session. An NE needs to support at least one threshold set for NE SOAM PM compliance. A second threshold set on the NE is desirable. More than two threshold sets on the NE can be configured if supported on the NE. All the objects in the row have a default value that disables the particular threshold measurement. In order to enable a threshold measurement the particular bit in the jnxSoamDmThresholdCfgEnable object is to be set to '1' and the selected threshold measurement is to have a threshold value configured. Non-configured threshold measurements are disabled by default. The writable objects in this table need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamDmThresholdCfgTable.

OBJECT-TYPE

The index of the threshold number for the specific DM threshold entry. An index value of '1' is to be supported. Other index values can be supported.

OBJECT-TYPE

A vector of bits that indicates the type of SOAM DM threshold notifications that are enabled. A bit set to '1' enables the specific SOAM DM threshold notification and when the specific counter is enabled and the threshold is crossed a notification is generated. A bit set to '0' disables the specific SOAM DM threshold notification. If a particular SOAM DM threshold is not supported the BIT value is set to '0'. bJnxSoamDmMeasuredFrameDelayTwoWayThreshold(0) Enables/disables measured frame two-way delay threshold notification. The notification is sent immediately when the jnxSoamDmMeasuredStatsFrameDelayTwoWay value is greater than or equal to threshold value. bJnxSoamDmMaxFrameDelayTwoWayThreshold(1) Enables/disables maximum frame two-way delay threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsFrameDelayTwoWayMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgFrameDelayTwoWayThreshold(2) Enables/disables average frame two-way delay threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsFrameDelayTwoWayAvg value is greater than or equal to the threshold value. bJnxSoamDmMeasuredIfdvTwoWayThreshold(3) Enables/disables measured frame IFDV two-way threshold notification. The notification is sent immediately when the jnxSoamDmMeasuredStatsIfdvTwoWay value is greater than or equal to threshold value. bJnxSoamDmMaxIfdvTwoWayThreshold(4) Enables/disables maximum frame IFDV two-way threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsIfdvTwoWayMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgIfdvTwoWayThreshold(5) Enables/disables average frame IFDV two-way threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsIfdvTwoWayAvg value is greater than or equal to the threshold value. bJnxSoamDmMaxFrameDelayRangeTwoWayThreshold(6) Enables/disables maximum Frame Delay Range two-way threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgFrameDelayRangeTwoWayThreshold(7) Enables/disables average Frame Delay Range two-way threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsFrameDelayRangeTwoWayAvg value is greater than or equal to the threshold value. bJnxSoamDmMeasuredFrameDelayForwardThreshold(8) Enables/disables measured forward frame delay threshold notification. The notification is sent immediately when the jnxSoamDmMeasuredStatsFrameDelayForward value is greater than or equal to threshold value. bJnxSoamDmMaxFrameDelayForwardThreshold(9) Enables/disables maximum forward frame delay threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsFrameDelayForwardMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgFrameDelayForwardThreshold(10) Enables/disables average forward frame delay threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsFrameDelayForwardAvg value is greater than or equal to the threshold value. bJnxSoamDmMeasuredIfdvForwardThreshold(11) Enables/disables measured frame IFDV forward threshold notification. The notification is sent immediately when the jnxSoamDmMeasuredStatsIfdvForward value is greater than or equal to threshold value. bJnxSoamDmMaxIfdvForwardThreshold(12) Enables/disables maximum frame IFDV forward threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsIfdvForwardMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgIfdvForwardThreshold(13) Enables/disables average frame IFDV forward threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsIfdvForwardAvg value is greater than or equal to the threshold value. bJnxSoamDmMaxFrameDelayRangeForwardThreshold(14) Enables/disables maximum Frame Delay Range forward threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsFrameDelayRangeForwardMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgFrameDelayRangeForwardThreshold(15) Enables/disables average Frame Delay Range forward threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsFrameDelayRangeForwardAvg value is greater than or equal to the threshold value. bJnxSoamDmMeasuredFrameDelayBackwardThreshold(16) Enables/disables measured backward frame delay threshold notification. The notification is sent immediately when the jnxSoamDmMeasuredStatsFrameDelayBackward value is greater than or equal to threshold value. bJnxSoamDmMaxFrameDelayBackwardThreshold(17) Enables/disables maximum backward frame delay threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsFrameDelayBackwardMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgFrameDelayBackwardThreshold(18) Enables/disables average backward frame delay threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsFrameDelayBackwardAvg value is greater than or equal to the threshold value. bJnxSoamDmMeasuredIfdvBackwardThreshold(19) Enables/disables measured frame IFDV backward threshold notification. The notification is sent immediately when the jnxSoamDmMeasuredStatsIfdvBackward value is greater than or equal to threshold value. bJnxSoamDmMaxIfdvBackwardThreshold(20) Enables/disables maximum frame IFDV backward threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsIfdvBackwardMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgIfdvBackwardThreshold(21) Enables/disables average frame IFDV backward threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsIfdvBackwardAvg value is greater than or equal to the threshold value. bJnxSoamDmMaxFrameDelayRangeBackwardThreshold(22) Enables/disables maximum Frame Delay Range backward threshold notification. The notification is sent immediately when the jnxSoamDmCurrentStatsFrameDelayRangeBackwardMax value is greater than or equal to threshold value in a Measurement Interval. bJnxSoamDmAvgFrameDelayRangeBackwardThreshold(23) Enables/disables average Frame Delay Range backward threshold notification. The notification is sent when at the end of a Measurement Interval if the jnxSoamDmCurrentStatsFrameDelayRangeBackwardAvg value is greater than or equal to the threshold value.

OBJECT-TYPE

This object is used to set the average two-way delay threshold value that will be used to determine if a threshold notification is generated.

OBJECT-TYPE

This object is used to set the average two-way IFDV threshold value that will be used to determine if a threshold notification is generated.

OBJECT-TYPE

The status of the row. The writable columns in a row cannot be changed if the row is active. All columns are to have a valid value before a row can be activated.

OBJECT-TYPE

This table includes configuration objects for the Delay Measurement bins to collect stats. Each row in the table is automatically created when the Delay Measurement session is defined for the selected MEP. The number of rows created is based upon three items: the DM type, the number of bins defined for each type, and whether bins are enabled for each type. The first four indices are the same as used to create the DM session: Maintenance Domain, MaNet, MEP identification, and jnxSoamDmCfgIndex. The fifth index is the type of bin, and the sixth index is the bin number. For a dmDmm session all nine types of bins can be created. For a dm1DmmTx session no bins are created. For a dm1DmmRx session only types forwardFrameDelay, forwardIfdv, and forwardFrameDelayRange can be created. The number of bins created for a bin type is based upon: the jnxSoamDmCfgNumMeasBinsPerFrameDelayInterval object, the jnxSoamDmCfgNumMeasBinsPerInterFrameDelayVariationInterval object, the jnxSoamDmCfgNumMeasBinsPerFrameDelayRangeInterval object, and the jnxSoamDmCfgMeasurementEnable object. For instance, if a dmDmm session with Bins per Frame Delay Interval set to 5, Bins per Frame Delay Variation Interval set to 3, and Frame Delay Range set to 2 (default), all of the appropriate bits set in jnxSoamDmMeasurementCfgEnable, the following number of rows would be created: For bin types TwoWayFrameDelay(1), forwardFrameDelay(2), and backwardFrameDelay(3) = 5 bins * 3 types = 15 rows For bin types TwoWayIfdv(4), forwardIfdv(5), backwardIfdv(6) = 3 bins * 3 types = 9 rows. For bins types twoWayFrameDelayRange(7), forwardFrameDelayRange(8), backwardFrameDelayRange(9) = 2 bins * 3 types = 6 rows. This gives a total of 30 rows created for the DMM session example. Each value in the bin defaults to 5000us greater than the previous bin, with the first bin default value set to 0. For the delay example above (5 bins), the following default values would be written to the bins: bin 1: 0 (range is 0us <= measurement < 5,000us) bin 2: 5000 (range is 5,000us <= measurement < 10,000us) bin 3: 10000 (range is 10,000us <= measurement < 15,000us) bin 4: 15000 (range is 15,000us <= measurement < 20,000us) bin 5: 20000 (range is 20,000us <= measurement < infinity) For the delay variation example above (3 bins), the following default values would be written to the bins: bin 1: 0 (range is 0us <= measurement < 5,000us) bin 2: 5000 (range is 5,000us <= measurement < 10,000us) bin 3: 10000 (range is 10,000us <= measurement < infinity) For the frame delay range example above (2 bins), the following default values would be written to the bins: bin 1: 0 (range is 0us <= measurement < 5,000us) bin 2: 5000 (range is 5,000us <= measurement < infinity) The writable objects in this table need to be persistent upon reboot or restart of a device. Rows are only created if the corresponding measurement type has been enabled via the jnxSoamDmCfgMeasurementEnable object.

OBJECT-TYPE

The conceptual row of jnxSoamDmCfgMeasBinTable.

OBJECT-TYPE

This object specifies whether the bin number is for Frame Delay or Inter-Frame Delay Variation.

OBJECT-TYPE

This object specifies the bin number for the configured boundary. The first bin has bin number 1.

OBJECT-TYPE

This object specifies the lower boundary for a measurement bin. The upper boundary is defined by the next bin value or infinite for the last bin defined. The measurement boundary for each measurement bin is to be larger than the measurement boundary of the preceding measurement bin. By default, the next bin is set to 5000us larger than the lower bin boundary. The values in a bin boundary object represents the time range used to segregate delay data into the appropriate statistical data bin. For five bins with default values, each bin has the following time range: bin 1 = 0, range is 0us <= measurement < 5,000us bin 2 = 5000, range is 5,000us <= measurement < 10,000us bin 3 = 10000, range is 10,000us <= measurement < 15,000us bin 4 = 15000, range is 15,000us <= measurement < 20,000us < infinity The first bin boundary (jnxSoamDmCfgBinNumber set to 1) always contains the value of 0. Attempting to write a non-zero value to this bin will result in an error.

OBJECT-TYPE

This table contains the result bins for the current Measurement Interval in a SOAM Delay Measurement session. Each row in the table represents the current bin statistics for a Delay Measurement session for the defined MEP. This table uses six indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific DM session on the selected MEP. The fifth index indicates bin type and the sixth indicates the specific bin number. A row in this table is created automatically by the SNMP Agent when the Delay Measurement session is configured and the bin counter value is set to 0. The objects in this table are ignored if jnxSoamDmCfgType is 1DmTx. This table applies only if the corresponding bit is set in jnxSoamDmCfgMeasurementEnable. The objects in this table do not need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamDmCurrentStatsBinsTable

OBJECT-TYPE

This object contains the count of the number of completed measurements initiated in this Measurement Interval whose value falls within the range specified for this bin (that is, greater than or equal to the measurement boundary for the bin, and (unless the bin is the last bin) less than the measurement boundary for the following bin.

OBJECT-TYPE

This table contains the result bins for the history Measurement Intervals in a SOAM Delay Measurement session. Rows of this table are created automatically by the SNMP Agent when the Delay Measurement session is running and a Measurement Interval is completed. Each row in the table represents the Measurement Interval history statistics for a specific bin in a Delay Measurement session for the defined MEP. This table uses seven indices. The first three indices are the indices of the Maintenance Domain, MaNet, and MEP tables. The fourth index is the specific DM session on the selected MEP. The fifth index is the Measurement Interval. The sixth index is the specific bin type. The seventh index is the specific bin number. Rows in this table pertaining to a given Measurement Interval are row in the jnxSoamDmHistoryStatsTable is deleted. The objects in this table are ignored if jnxSoamDmCfgType is 1DmTx. This table applies only if the corresponding bit is set in jnxSoamDmCfgMeasurementEnable. The objects in this table need to be persistent upon reboot or restart of a device.

OBJECT-TYPE

The conceptual row of jnxSoamDmHistoryStatsBinsTable

OBJECT-TYPE

This object contains the count of the number of completed measurements initiated in this Measurement Interval whose value falls within the range specified for this bin (that is, greater than or equal to the measurement boundary for the bin, and (unless the bin is the last bin) less than the measurement boundary for the following bin.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object contains the time and date at the time that the notification event is detected, not the time of the notification generation. This object is used only for notifications. The mechanism to set and keep current the date and time is not specified.

OBJECT-TYPE

The Object Identifier of the object that caused the generation of the notification from the jnxSoamLmThresholdEntry or jnxSoamDmThresholdEntry. This object is only used for the notification.

OBJECT-TYPE

The configured threshold value of the object that caused the generation of the notification. This object is only used for the notification.

OBJECT-TYPE

The measured value of the object at the time of the generation of the Notification, from the jnxSoamLmMeasuredStatsTable, jnxSoamLmCurrentStatsTable, jnxSoamDmMeasuredStatsTable or jnxSoamDmCurrentStatsTable. This object is only used for the notification.

OBJECT-TYPE

The suspect flag for the current Measurement Interval in which the notification was generated from the jnxSoamLmCurrentStatsTable, or jnxSoamDmCurrentStatsTable. This object is only used for the notification.

OBJECT-TYPE

The Notification Crossing Type of the object that caused the generation of the notification from the jnxSoamLmThresholdEntry or jnxSoamDmThresholdEntry. aboveAlarm(1) indicates that the crossing type alarm was an above threshold setAlarm(2) indicates that the crossing type alarm was a set threshold clearAlarm(3) indicates that the crossing type alarm was a clear threshold This object is only used for the notification.

OBJECT-TYPE

The MAC address of the Destination MEP associated the notification found in either the jnxSoamDmCfgTable or jnxSoamLmCfgTable. This object is only used for the notification.

OBJECT-TYPE

The CoS priority of the associated notification found in either the jnxSoamDmCfgTable or jnxSoamLmCfgTable. This object is only used for the notification.

OBJECT-TYPE

The measured value of total number of flaps occured during the flap trap timer itnerval.

OBJECT-TYPE

The measured value of total number of accumulated flaps occured during the flap trap timer itnerval.

OBJECT-TYPE

The measured value of the object at the time of the generation of the last Notification during the flap trap timer interval. This object is only used for the notification.

OBJECT-TYPE

The Current Notification Crossing Type of the object that caused the generation of the notification at the end of timer interval from the jnxSoamLmThresholdEntry or jnxSoamDmThresholdEntry. aboveAlarm(1) indicates that the crossing type alarm was an above threshold setAlarm(2) indicates that the crossing type alarm was a set threshold clearAlarm(3) indicates that the crossing type alarm was a clear threshold This object is only used for the notification.

OBJECT-TYPE

This object contains the time and date at the time that the last notification event is detected, at the end of flap timer interval and not the time of the first notification generation. This object is used only for notifications. The mechanism to set and keep current the date and time is not specified.

OBJECT-IDENTITY