IMA-MIB
- Registered at
- 1.3.6.1.4.1.353.5.7
- Last updated
- 1999-02-11 18:30
- Organization
- The ATM Forum
- Revisions
- 1999-02-11 18:30, 1997-01-09 22:45
- Namespace
- standard
- Source file
IMA-MIB- Digest
sha256:50e69f30e939d9360f10f052e53c442f29788fc6fe3d828cadd9eee9e76839f7
Description
The MIB module for managing ATM Forum Inverse Multiplexing for ATM (IMA) interfaces.
Contact
ATM Forum World Headquarters 2570 West El Camino Real Suite 304 Mountain View, CA 94040-1313 USA Phone: +1 415 949 6700 Fax: +1 415 949 6705 email: info@atmforum.com
Imports
| From | Symbols |
|---|---|
| IF-MIB | InterfaceIndex, InterfaceIndexOrZero, ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Gauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso |
| SNMPv2-TC | DateAndTime, DisplayString, RowStatus, TEXTUAL-CONVENTION |
Imported by
3 module(s) in this corpus import this one.
Load order
Every file a consumer needs in order to load this module, dependencies first.
IANAifType-MIB IF-MIB IMA-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ImaAlarmStatus TEXTUAL-CONVENTION A qualification of the IMA trap which indicates if the condition causing the trap has been detected (declared) or is no longer present (cleared). | current | |||
| ImaAlarmType TEXTUAL-CONVENTION An identification of the event that caused the generation of the IMA trap. | current | |||
| ImaFrameLength TEXTUAL-CONVENTION Length of the IMA frames. | current | |||
| ImaGroupFailureStatus TEXTUAL-CONVENTION Failure reason of an IMA group. | current | |||
| ImaGroupState TEXTUAL-CONVENTION State of the IMA group. | current | |||
| ImaGroupSymmetry TEXTUAL-CONVENTION The group symmetry mode adjusted during the group start-up. | current | |||
| ImaGroupTxClkMode TEXTUAL-CONVENTION Indicate the transmit clock mode of the IMA group. There are two possible modes: the Common Transmit Clock (CTC) and the Independent Transmit Clock (ITC). The CTC mode corresponds to the case when the transmit clock of all IMA links are derived from the same source. The ITC configuration corresponds to the case where there is at least one IMA link whose transmit clock is derived from a source different than at least another link transmit clock. | current | |||
| ImaLinkFailureStatus TEXTUAL-CONVENTION Local failure status of a link belonging to an IMA group. | current | |||
| ImaLinkState TEXTUAL-CONVENTION State of a link belonging to an IMA group. | current | |||
| ImaTestProcStatus TEXTUAL-CONVENTION States of the Test Pattern Procedure. | current | |||
| MilliSeconds TEXTUAL-CONVENTION Time in milliseconds | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| atmForum OBJECT-IDENTITY | 1.3.6.1.4.1.353 | |||
| atmForumNetworkManagement OBJECT-IDENTITY | 1.3.6.1.4.1.353.5 | |||
| atmfIma OBJECT-IDENTITY | 1.3.6.1.4.1.353.5.7 | |||
| atmfImaMibObjects OBJECT-IDENTITY | 1.3.6.1.4.1.353.5.7.1.1 | |||
| imaGroupNumber OBJECT-TYPE The number of IMA groups configured on this system. | 1.3.6.1.4.1.353.5.7.1.1.1 | INTEGER (0..2147483647) | read-only | current |
| imaGroupTable OBJECT-TYPE The IMA Group Configuration table. | 1.3.6.1.4.1.353.5.7.1.1.2 | not-accessible | current | |
| imaGroupEntry OBJECT-TYPE An entry in the IMA Group table. | 1.3.6.1.4.1.353.5.7.1.1.2.1 | not-accessible | current | |
| imaGroupIndex OBJECT-TYPE A unique value for the IMA Group. | 1.3.6.1.4.1.353.5.7.1.1.2.1.1 | INTEGER (1..2147483647) | not-accessible | current |
| imaGroupRowStatus OBJECT-TYPE The imaGroupRowStatus object allows create, change, and delete operations on imaGroupTable entries. To create a new conceptual row (or instance) of the imaGroupTable, imaGroupRowStatus must be set to 'createAndWait' or 'createAndGo'. If settable, a successful set of the following objects must be performed before the imaGroupRowStatus of a new conceptual row can be set to 'active': imaGroupMinNumTxLinks imaGroupMinNumRxLinks imaGroupTxImaId Some objects in the imaGroupTable control settings which can only be established or changed at group start-up time. These objects include: imaGroupTxImaId imaGroupSymmetry imaGroupTxFrameLength To change (modify) the imaGroupTxImaId object, the manager must first set imaGroupRowStatus to 'notInService'. However, changes to the following two objects can be optionally allowed while the imaGroupRowStatus is 'active': imaGroupSymmetry imaGroupTxFrameLength These two objects can be changed when the imaGroupRowStatus is 'active' in order to allow the far-end to recover from its Config-Aborted state without having to force the near-end Group State machine to go to the 'Not Configured' state. Changing these object values after group start-up has completed causes a restart of the IMA group. Alternatively, as noted above, the agent implementation may simply require the imaGroupRowStatus object to first be set to 'notInService' before allowing changes to either of these two objects. To remove (delete) an imaGroupTable entry from this table, set imaGroupRowStatus to 'destroy'. Setting the imaGroupRowStatus to 'active' has the effect of activating the Group Startup Procedure. The Group Startup Procedure uses provisioned links that have imaLinkRowStatus set to 'active' and imaLinkGroupIndex set to the imaGroupIndex in this conceptual row. When the imaGroupRowStatus is not in 'active' state, the Group State machine is in its 'Not Configured' state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.2 | RowStatus | read-create | current |
| imaGroupIfIndex OBJECT-TYPE This object identifies the logical interface number ('ifIndex') assigned to this IMA group, and is used to identify corresponding rows in the Interfaces MIB. Note that re-initialization of the management agent may cause a client's 'imaGroupIfIndex' to change. | 1.3.6.1.4.1.353.5.7.1.1.2.1.3 | InterfaceIndex | read-only | current |
| imaGroupNeState OBJECT-TYPE The current operational state of the near-end IMA Group State Machine. | 1.3.6.1.4.1.353.5.7.1.1.2.1.4 | ImaGroupState | read-only | current |
| imaGroupFeState OBJECT-TYPE The current operational state of the far-end IMA Group State Machine. | 1.3.6.1.4.1.353.5.7.1.1.2.1.5 | ImaGroupState | read-only | current |
| imaGroupFailureStatus OBJECT-TYPE The current failure status of the IMA group (the reason why the GTSM is in the down state). | 1.3.6.1.4.1.353.5.7.1.1.2.1.6 | ImaGroupFailureStatus | read-only | current |
| imaGroupSymmetry OBJECT-TYPE Symmetry of the IMA group. | 1.3.6.1.4.1.353.5.7.1.1.2.1.7 | ImaGroupSymmetry | read-create | current |
| imaGroupMinNumTxLinks OBJECT-TYPE Minimum number of transmit links required to be Active for the IMA group to be in the Operational state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.8 | INTEGER (1..32) | read-create | current |
| imaGroupMinNumRxLinks OBJECT-TYPE Minimum number of receive links required to be Active for the IMA group to be in the Operational state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.9 | INTEGER (1..32) | read-create | current |
| imaGroupNeTxClkMode OBJECT-TYPE Transmit clocking mode used by the near-end IMA group. | 1.3.6.1.4.1.353.5.7.1.1.2.1.10 | ImaGroupTxClkMode | read-create | current |
| imaGroupFeTxClkMode OBJECT-TYPE Transmit clocking mode used by the far-end IMA group. | 1.3.6.1.4.1.353.5.7.1.1.2.1.11 | ImaGroupTxClkMode | read-only | current |
| imaGroupTxTimingRefLink OBJECT-TYPE The ifIndex of the transmit timing reference link to be used by the near-end for IMA data cell clock recovery from the ATM layer. The distinguished value of zero may be used if no link has been configured in the IMA group, or if the transmit timing reference link has not yet been selected. | 1.3.6.1.4.1.353.5.7.1.1.2.1.12 | InterfaceIndexOrZero | read-only | current |
| imaGroupRxTimingRefLink OBJECT-TYPE The ifIndex of the receive timing reference link to be used by near-end for IMA data cell clock recovery toward the ATM layer. The distinguished value of zero may be used if no link has been configured in the IMA group, or if the receive timing reference link has not yet been detected. | 1.3.6.1.4.1.353.5.7.1.1.2.1.13 | InterfaceIndexOrZero | read-only | current |
| imaGroupLastChange OBJECT-TYPE The time-of-day the IMA group last changed operational state (i.e., value of imaGroupNeState changed). | 1.3.6.1.4.1.353.5.7.1.1.2.1.14 | DateAndTime | read-only | current |
| imaGroupTxImaId OBJECT-TYPE The IMA ID currently in use by the near-end IMA function. | 1.3.6.1.4.1.353.5.7.1.1.2.1.15 | INTEGER (0..255) | read-create | current |
| imaGroupRxImaId OBJECT-TYPE The IMA ID currently in use by the far-end IMA function. | 1.3.6.1.4.1.353.5.7.1.1.2.1.16 | INTEGER (0..255) | read-only | current |
| imaGroupTxFrameLength OBJECT-TYPE The frame length to be used by the IMA group in the transmit direction. Can only be set when the IMA group is startup. | 1.3.6.1.4.1.353.5.7.1.1.2.1.17 | ImaFrameLength | read-create | current |
| imaGroupRxFrameLength OBJECT-TYPE Value of IMA frame length as received from remote IMA function. | 1.3.6.1.4.1.353.5.7.1.1.2.1.18 | ImaFrameLength | read-only | current |
| imaGroupDiffDelayMax OBJECT-TYPE The maximum number of milliseconds of differential delay among the links that will be tolerated on this interface. | 1.3.6.1.4.1.353.5.7.1.1.2.1.19 | MilliSeconds | read-create | current |
| imaGroupLeastDelayLink OBJECT-TYPE The ifIndex of the link configured in the IMA group which has the smallest link propagation delay. The distinguished value of zero may be used if no link has been configured in the IMA group, or if the link with the smallest link propagation delay has not yet been determined. | 1.3.6.1.4.1.353.5.7.1.1.2.1.20 | InterfaceIndexOrZero | read-only | current |
| imaGroupDiffDelayMaxObs OBJECT-TYPE The latest maximum differential delay observed (in milliseconds) between the links having the least and most link propagation delay, among the receive links that are currently configured in the IMA group. | 1.3.6.1.4.1.353.5.7.1.1.2.1.21 | MilliSeconds | read-only | current |
| imaGroupAlphaValue OBJECT-TYPE This indicates the 'alpha' value used to specify the number of consecutive invalid ICP cells to be detected before moving to the IMA Hunt state from the IMA Sync state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.22 | INTEGER (1..2) | read-create | current |
| imaGroupBetaValue OBJECT-TYPE This indicates the 'beta' value used to specify the number of consecutive errored ICP cells to be detected before moving to the IMA Hunt state from the IMA Sync state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.23 | INTEGER (1..5) | read-create | current |
| imaGroupGammaValue OBJECT-TYPE This indicates the 'gamma' value used to specify the number of consecutive valid ICP cells to be detected before moving to the IMA Sync state from the IMA PreSync state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.24 | INTEGER (1..5) | read-create | current |
| imaGroupRunningSecs OBJECT-TYPE The amount of time (in seconds) since this IMA group has been in the Operational state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.25 | Gauge32 | read-only | current |
| imaGroupUnavailSecs OBJECT-TYPE Count of one second intervals where the IMA Group Traffic State Machine is Down. | 1.3.6.1.4.1.353.5.7.1.1.2.1.26 | Counter32 | read-only | current |
| imaGroupNeNumFailures OBJECT-TYPE The number of times a near-end group failure (Config-Aborted, Insufficient-Links) has been reported since power-up or reboot. | 1.3.6.1.4.1.353.5.7.1.1.2.1.27 | Counter32 | read-only | current |
| imaGroupFeNumFailures OBJECT-TYPE The number of times a far-end group failure (Config-Aborted-FE, Insufficient-Links-FE, Blocked-FE) has been reported since power-up or reboot. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.2.1.28 | Counter32 | read-only | current |
| imaGroupTxAvailCellRate OBJECT-TYPE The current cell rate (truncated value in cells per second) provided by this IMA group in the transmit direction, considering all the transmit links in the Active state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.29 | Gauge32 | read-only | current |
| imaGroupRxAvailCellRate OBJECT-TYPE The current cell rate (truncated value in cells per second) provided by this IMA group in the receive direction, considering all the receive links in the Active state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.30 | Gauge32 | read-only | current |
| imaGroupNumTxCfgLinks OBJECT-TYPE The number of links that are configured to transmit in this IMA group. This attribute overwrites the value of the imaGroupNumRxActLinks attribute when the IMA group is configured in the Symmetrical Configuration group symmetry mode. | 1.3.6.1.4.1.353.5.7.1.1.2.1.31 | Gauge32 | read-only | current |
| imaGroupNumRxCfgLinks OBJECT-TYPE The number of links that are configured to receive in this IMA group. This attribute is overwritten by the value of the imaGroupNumTxActLinks attribute when the IMA group is configured in the Symmetrical Configuration group symmetry mode. | 1.3.6.1.4.1.353.5.7.1.1.2.1.32 | Gauge32 | read-only | current |
| imaGroupNumTxActLinks OBJECT-TYPE The number of links which are configured to transmit and are currently Active in this IMA group. | 1.3.6.1.4.1.353.5.7.1.1.2.1.33 | Gauge32 | read-only | current |
| imaGroupNumRxActLinks OBJECT-TYPE The number of links which are configured to receive and are currently Active in this IMA group. | 1.3.6.1.4.1.353.5.7.1.1.2.1.34 | Gauge32 | read-only | current |
| imaGroupTestLinkIfIndex OBJECT-TYPE This object is used to designate an interface as the test link for use in the Test Pattern Procedure. The distinguished value of zero specifies that the implementation may choose the Test Link, in which case, the implementation may also choose the value of 'imaGroupTestPattern'. The value zero may also be used if no link has yet been added to the group. Note that this value is NOT the same as the Tx LID value, but instead either identifies the ifIndex value of the test link to be used by the Test Pattern Procedure (i.e., the link whose LID value is inserted in the Tx LID field of the transmitted ICP cells), or identifies that the implementation may choose the test link (if the value is zero). | 1.3.6.1.4.1.353.5.7.1.1.2.1.35 | InterfaceIndexOrZero | read-create | current |
| imaGroupTestPattern OBJECT-TYPE The value of this object is used to specify the Tx Test Pattern in an IMA group loopback operation. A value in the range 0 to 255 designates a specific pattern. The distinguished value of -1 specifies that the implementation may choose the value. In this case, the implementation may also choose the value of 'imaGroupTestLinkIfIndex'. It is recommended that the specific value 255 not be used for testing, since by (R-137) the IMA interface is required to transmit 0xFF (i.e., 255) when the incoming test command is inactive or the test link is not detected, and thus it cannot be established for certain whether 255 was received due to an actual loopback operation or due to the normal operation of an IMA that is not performing (or else cannot perform) the test pattern procedure. | 1.3.6.1.4.1.353.5.7.1.1.2.1.36 | INTEGER (-1..255) | read-create | current |
| imaGroupTestProcStatus OBJECT-TYPE This object is used to enable or disable the Test Pattern Procedure, and to note whether at least one link failed the test. The test is started by setting operating(2) status. If any link should fail the test, the IMA will set the status to linkFail(3). The linkFail(3) state will persist until either the disabled(1) state is set or until no instance of imaLinkTestProcStatus has the value linkFail(3). Only the values disabled(1) and operating(2) may be written. Writing the operating(2) value will not cause clearing of the linkFail(3) state. | 1.3.6.1.4.1.353.5.7.1.1.2.1.37 | ImaTestProcStatus | read-create | current |
| imaGroupValidIntervals OBJECT-TYPE The number of previous 15 minute intervals for which valid data was collected. The value will be 96 unless the IMA group table entry was created within the last 24 hours, in which case the value will be the number of complete 15 minute intervals since the IMA group table entry was created. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this value is the maximum interval number for which valid data is available. This attribute is only mandatory when the IMA Group Interval Statistics and/or IMA Group Total Statistics objects are implemented. | 1.3.6.1.4.1.353.5.7.1.1.2.1.38 | INTEGER (0..96) | read-only | current |
| imaGroupInvalidIntervals OBJECT-TYPE The number of intervals for which no valid data is available. This attribute is only mandatory when the IMA Group Interval Statistics and/or IMA Group Total Statistics objects are implemented. | 1.3.6.1.4.1.353.5.7.1.1.2.1.39 | INTEGER (0..96) | read-only | current |
| imaGroupTimeElapsed OBJECT-TYPE The number of seconds that have elapsed since the beginning of the current measurement period. This attribute is only mandatory when the IMA Group Current Statistics are implemented. | 1.3.6.1.4.1.353.5.7.1.1.2.1.40 | INTEGER (0..899) | read-only | current |
| imaGroupTxOamLabelValue OBJECT-TYPE IMA OAM Label value transmitted by the NE IMA unit. | 1.3.6.1.4.1.353.5.7.1.1.2.1.41 | INTEGER (1..255) | read-only | current |
| imaGroupRxOamLabelValue OBJECT-TYPE IMA OAM Label value transmitted by the FE IMA unit. The value 0 likely means that the IMA unit has not received an OAM Label from the FE IMA unit at this time. | 1.3.6.1.4.1.353.5.7.1.1.2.1.42 | INTEGER (0..255) | read-only | current |
| imaGroupMappingTable OBJECT-TYPE A table mapping the 'ifIndex' values of 'imaGroupIfIndex' to the 'imaGroupIndex' values of the corresponding IMA group. | 1.3.6.1.4.1.353.5.7.1.1.3 | not-accessible | current | |
| imaGroupMappingEntry OBJECT-TYPE Each row describes one ifIndex to imaGroupIndex mapping. | 1.3.6.1.4.1.353.5.7.1.1.3.1 | not-accessible | current | |
| imaGroupMappingIndex OBJECT-TYPE The imaGroupIndex of the IMA Group which implements the specified interface. | 1.3.6.1.4.1.353.5.7.1.1.3.1.1 | Integer32 | read-only | current |
| imaLinkTable OBJECT-TYPE The IMA group Link Status and Configuration table. | 1.3.6.1.4.1.353.5.7.1.1.4 | not-accessible | current | |
| imaLinkEntry OBJECT-TYPE An entry in the IMA Group Link table. | 1.3.6.1.4.1.353.5.7.1.1.4.1 | not-accessible | current | |
| imaLinkIfIndex OBJECT-TYPE This corresponds to the 'ifIndex' of the MIB-II interface on which this link is established. This object also corresponds to the logical number ('ifIndex') assigned to this IMA link. | 1.3.6.1.4.1.353.5.7.1.1.4.1.1 | InterfaceIndex | not-accessible | current |
| imaLinkRowStatus OBJECT-TYPE The imaLinkRowStatus object allows create, change, and delete operations on imaLinkTable entries. To create a new conceptual row (or instance) of the imaLinkTable, imaLinkRowStatus must be set to 'createAndWait' or 'createAndGo'. A successful set of the imaLinkGroupIndex object must be performed before the imaLinkRowStatus of a new conceptual row can be set to 'active'. To change (modify) the imaLinkGroupIndex in an imaLinkTable entry, the imaLinkRowStatus object must first be set to 'notInService'. Only then can this object in the conceptual row be modified. This is due to the fact that the imaLinkGroupIndex object provides the association between a physical IMA link and the IMA group to which it belongs, and setting the imaLinkGroupIndex object to a different value has the effect of changing the association between a physical IMA link and an IMA group. To place the link 'in group', the imaLinkRowStatus object is set to 'active'. While the row is not in 'active' state, both the Transmit and Receive IMA link state machines are in the 'Not In Group' state. To remove (delete) an imaLinkTable entry from this table, set this object to 'destroy'. | 1.3.6.1.4.1.353.5.7.1.1.4.1.2 | RowStatus | read-create | current |
| imaLinkGroupIndex OBJECT-TYPE The value which identifies the IMA group (imaGroupIndex) of which this link is a member. | 1.3.6.1.4.1.353.5.7.1.1.4.1.3 | Integer32 | read-create | current |
| imaLinkNeTxState OBJECT-TYPE The current state of the near-end transmit link. | 1.3.6.1.4.1.353.5.7.1.1.4.1.4 | ImaLinkState | read-only | current |
| imaLinkNeRxState OBJECT-TYPE The current state of the near-end receive link. | 1.3.6.1.4.1.353.5.7.1.1.4.1.5 | ImaLinkState | read-only | current |
| imaLinkFeTxState OBJECT-TYPE The current state of the far-end transmit link as reported via ICP cells. | 1.3.6.1.4.1.353.5.7.1.1.4.1.6 | ImaLinkState | read-only | current |
| imaLinkFeRxState OBJECT-TYPE The current state of the far-end receive link as reported via ICP cells. | 1.3.6.1.4.1.353.5.7.1.1.4.1.7 | ImaLinkState | read-only | current |
| imaLinkNeRxFailureStatus OBJECT-TYPE The current link failure status of the near-end receive link. | 1.3.6.1.4.1.353.5.7.1.1.4.1.8 | ImaLinkFailureStatus | read-only | current |
| imaLinkFeRxFailureStatus OBJECT-TYPE The current link failure status of the far-end receive link as reported via ICP cells. | 1.3.6.1.4.1.353.5.7.1.1.4.1.9 | ImaLinkFailureStatus | read-only | current |
| imaLinkTxLid OBJECT-TYPE The outgoing LID used currently on the link by the local end. This value has meaning only if the link belongs to an IMA group. | 1.3.6.1.4.1.353.5.7.1.1.4.1.10 | INTEGER (0..31) | read-only | current |
| imaLinkRxLid OBJECT-TYPE The incoming LID used currently on the link by the remote end as reported via ICP cells. This value has meaning only if the link belongs to an IMA group. | 1.3.6.1.4.1.353.5.7.1.1.4.1.11 | INTEGER (0..31) | read-only | current |
| imaLinkRelDelay OBJECT-TYPE The latest measured delay on this link relative to the link, in the same IMA group, with the least delay. | 1.3.6.1.4.1.353.5.7.1.1.4.1.12 | MilliSeconds | read-only | current |
| imaLinkImaViolations OBJECT-TYPE ICP violations: count of errored, invalid or missing ICP cells, except during SES-IMA or UAS-IMA conditions. | 1.3.6.1.4.1.353.5.7.1.1.4.1.13 | Counter32 | read-only | current |
| imaLinkOifAnomalies OBJECT-TYPE The number of OIF anomalies, except during SES-IMA or UAS-IMA conditions, at the near-end. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.4.1.14 | Counter32 | read-only | current |
| imaLinkNeSevErroredSecs OBJECT-TYPE Count of one second intervals containing >= 30% of the ICP cells counted as IV-IMAs, or one or more link defects (e.g., LOS, OOF/LOF, AIS, or LCD), LIF defects, or LODS defects, except during UAS-IMA condition. | 1.3.6.1.4.1.353.5.7.1.1.4.1.15 | Counter32 | read-only | current |
| imaLinkFeSevErroredSecs OBJECT-TYPE Count of one second intervals containing one or more RDI-IMA defects, except during UAS-IMA-FE condition. | 1.3.6.1.4.1.353.5.7.1.1.4.1.16 | Counter32 | read-only | current |
| imaLinkNeUnavailSecs OBJECT-TYPE Count of unavailable seconds at near-end: unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA. | 1.3.6.1.4.1.353.5.7.1.1.4.1.17 | Counter32 | read-only | current |
| imaLinkFeUnavailSecs OBJECT-TYPE Count of unavailable seconds at far-end: unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE. | 1.3.6.1.4.1.353.5.7.1.1.4.1.18 | Counter32 | read-only | current |
| imaLinkNeTxUnusableSecs OBJECT-TYPE Tx Unusable seconds: count of Tx Unusable seconds at the near-end Tx LSM. | 1.3.6.1.4.1.353.5.7.1.1.4.1.19 | Counter32 | read-only | current |
| imaLinkNeRxUnusableSecs OBJECT-TYPE Rx Unusable seconds: count of Rx Unusable seconds at the near-end Rx LSM. | 1.3.6.1.4.1.353.5.7.1.1.4.1.20 | Counter32 | read-only | current |
| imaLinkFeTxUnusableSecs OBJECT-TYPE Tx Unusable seconds at far-end: count of seconds with Tx Unusable indications from the far-end Tx LSM. | 1.3.6.1.4.1.353.5.7.1.1.4.1.21 | Counter32 | read-only | current |
| imaLinkFeRxUnusableSecs OBJECT-TYPE Rx Unusable seconds at far-end: count of seconds with Rx Unusable indications from the far-end Rx LSM. | 1.3.6.1.4.1.353.5.7.1.1.4.1.22 | Counter32 | read-only | current |
| imaLinkNeTxNumFailures OBJECT-TYPE The number of times a near-end transmit failure alarm condition has been entered on this link (i.e., some form of implementation specific transmit fault). | 1.3.6.1.4.1.353.5.7.1.1.4.1.23 | Counter32 | read-only | current |
| imaLinkNeRxNumFailures OBJECT-TYPE The number of times a near-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, RFI-IMA, Mis-Connected or some form of implementation specific receive fault). | 1.3.6.1.4.1.353.5.7.1.1.4.1.24 | Counter32 | read-only | current |
| imaLinkFeTxNumFailures OBJECT-TYPE The number of times a far-end transmit failure alarm condition has been entered on this link (i.e., Tx-Unusable-FE). This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.4.1.25 | Counter32 | read-only | current |
| imaLinkFeRxNumFailures OBJECT-TYPE The number of times a far-end receive failure alarm condition has been entered on this link (i.e., Rx-Unusable-FE). This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.4.1.26 | Counter32 | read-only | current |
| imaLinkTxStuffs OBJECT-TYPE Count of stuff events inserted in the transmit direction. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.4.1.27 | Counter32 | read-only | current |
| imaLinkRxStuffs OBJECT-TYPE Count of stuff events detected in the receive direction. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.4.1.28 | Counter32 | read-only | current |
| imaLinkRxTestPattern OBJECT-TYPE This object identifies the test pattern received in the ICP Cell (octet 17) on the link during the IMA Test Pattern Procedure. This value may then be compared to the transmitted test pattern. | 1.3.6.1.4.1.353.5.7.1.1.4.1.29 | INTEGER (0..255) | read-only | current |
| imaLinkTestProcStatus OBJECT-TYPE This value indicates the current state of the Test Pattern Procedure. If the value is disabled(1), the test is not running. A value of operating(2) means the test is running and no error has been found on this interface. A value of linkFail(3) means an error has been detected on this link during the test. Once an error is detected, the linkFail(3) value is latched until either this object is read or until the imaGroupTestProcStatus is moved to disabled(1). Once read, if the error no longer persists, a subsequent read will report the value operating(2). | 1.3.6.1.4.1.353.5.7.1.1.4.1.30 | ImaTestProcStatus | read-only | current |
| imaLinkValidIntervals OBJECT-TYPE The number of previous 15 minute intervals for which valid data was collected. The value will be 96 unless the IMA group table entry was created within the last 24 hours, in which case the value will be the number of complete 15 minute intervals since the IMA group table entry was created. In the case where the agent is a proxy, it is possible that some intervals are unavailable. In this case, this value is the maximum interval number for which valid data is available. This attribute is only mandatory when the IMA Link Interval Statistics and/or IMA Link Total Statistics objects are implemented. | 1.3.6.1.4.1.353.5.7.1.1.4.1.31 | INTEGER (0..96) | read-only | current |
| imaLinkInvalidIntervals OBJECT-TYPE The number of intervals for which no valid data is available. This attribute is only mandatory when the IMA Link Interval Statistics and/or IMA Link Total Statistics objects are implemented. | 1.3.6.1.4.1.353.5.7.1.1.4.1.32 | INTEGER (0..96) | read-only | current |
| imaLinkTimeElapsed OBJECT-TYPE The number of seconds that have elapsed since the beginning of the current measurement period. This attribute is only mandatory when the IMA Link Current Statistics are implemented. | 1.3.6.1.4.1.353.5.7.1.1.4.1.33 | INTEGER (0..899) | read-only | current |
| imaAlarmStatus OBJECT-TYPE Status of the IMA alarm. | 1.3.6.1.4.1.353.5.7.1.1.5 | ImaAlarmStatus | read-only | current |
| imaAlarmType OBJECT-TYPE The Type of IMA alarm declared or cleared. The value of ImaAlarmType identifies the type of alarm according to the definitions in the IMA specification. | 1.3.6.1.4.1.353.5.7.1.1.6 | ImaAlarmType | read-only | current |
| imaGroupCurrentTable OBJECT-TYPE The IMA Group Current table. | 1.3.6.1.4.1.353.5.7.1.1.7 | not-accessible | current | |
| imaGroupCurrentEntry OBJECT-TYPE An entry in the IMA Group Current table. | 1.3.6.1.4.1.353.5.7.1.1.7.1 | not-accessible | current | |
| imaGroupCurrentUnavailSecs OBJECT-TYPE Count of one second intervals where the IMA Group Traffic State Machine is Down in the current 15 minutes interval. | 1.3.6.1.4.1.353.5.7.1.1.7.1.1 | Gauge32 | read-only | current |
| imaGroupCurrentNeNumFailures OBJECT-TYPE The number of times a near-end group failure (Config-Aborted, Insufficient-Links) has been reported in the current 15 minutes interval. | 1.3.6.1.4.1.353.5.7.1.1.7.1.2 | Gauge32 | read-only | current |
| imaGroupCurrentFeNumFailures OBJECT-TYPE The number of times a far-end group failure (Config-Aborted-FE, Insufficient-Links-FE, Blocked-FE) has been reported in the current 15 minutes interval. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.7.1.3 | Gauge32 | read-only | current |
| imaGroupIntervalTable OBJECT-TYPE The IMA Group Interval table. | 1.3.6.1.4.1.353.5.7.1.1.8 | not-accessible | current | |
| imaGroupIntervalEntry OBJECT-TYPE An entry in the IMA Group Interval table. | 1.3.6.1.4.1.353.5.7.1.1.8.1 | not-accessible | current | |
| imaGroupIntervalNumber OBJECT-TYPE A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). | 1.3.6.1.4.1.353.5.7.1.1.8.1.1 | INTEGER (1..96) | not-accessible | current |
| imaGroupIntervalUnavailSecs OBJECT-TYPE Count of one second intervals where the IMA Group Traffic State Machine is Down in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.8.1.2 | Gauge32 | read-only | current |
| imaGroupIntervalNeNumFailures OBJECT-TYPE The number of times a near-end group failure (Config-Aborted, Insufficient-Links) has been reported in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.8.1.3 | Gauge32 | read-only | current |
| imaGroupIntervalFeNumFailures OBJECT-TYPE The number of times a far-end group failure (Config-Aborted-FE, Insufficient-Links-FE, Blocked-FE) has been reported in one of the previous 96, individual 15 minute, intervals. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.8.1.4 | Gauge32 | read-only | current |
| imaGroupTotalTable OBJECT-TYPE The IMA Group Total table. | 1.3.6.1.4.1.353.5.7.1.1.9 | not-accessible | current | |
| imaGroupTotalEntry OBJECT-TYPE An entry in the IMA Group Total table. | 1.3.6.1.4.1.353.5.7.1.1.9.1 | not-accessible | current | |
| imaGroupTotalUnavailSecs OBJECT-TYPE Count of one second intervals where the IMA Group Traffic State Machine is Down in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.9.1.1 | Gauge32 | read-only | current |
| imaGroupTotalNeNumFailures OBJECT-TYPE The number of times a near-end group failure (Config-Aborted, Insufficient-Links) has been reported in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.9.1.2 | Gauge32 | read-only | current |
| imaGroupTotalFeNumFailures OBJECT-TYPE The number of times a far-end group failure (Config-Aborted-FE, Insufficient-Links-FE, Blocked-FE) has been reported in the previous 24 hour interval. Invalid 15 minute intervals count as 0. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.9.1.3 | Gauge32 | read-only | current |
| imaLinkCurrentTable OBJECT-TYPE The IMA Link Current table. | 1.3.6.1.4.1.353.5.7.1.1.10 | not-accessible | current | |
| imaLinkCurrentEntry OBJECT-TYPE An entry in the IMA Link Current table. | 1.3.6.1.4.1.353.5.7.1.1.10.1 | not-accessible | current | |
| imaLinkCurrentImaViolations OBJECT-TYPE ICP violations: count of errored, invalid or missing ICP cells, except during SES-IMA or UAS-IMA conditions, in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.1 | Gauge32 | read-only | current |
| imaLinkCurrentOifAnomalies OBJECT-TYPE The number of OIF anomalies, except during SES-IMA or UAS-IMA conditions, at the near-end in the current 15 minute interval. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.10.1.2 | Gauge32 | read-only | current |
| imaLinkCurrentNeSevErroredSecs OBJECT-TYPE Count of one second intervals containing >= 30% of the ICP cells counted as IV-IMAs, or one or more link defects (e.g., LOS, OOF/LOF, AIS, or LCD), LIF defects, or LODS defects, except during UAS-IMA condition, in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.3 | Gauge32 | read-only | current |
| imaLinkCurrentFeSevErroredSecs OBJECT-TYPE Count of one second intervals containing one or more RDI-IMA defects, except during UAS-IMA-FE condition, in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.4 | Gauge32 | read-only | current |
| imaLinkCurrentNeUnavailSecs OBJECT-TYPE Count of unavailable seconds at near-end in the current 15 minute interval: unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA. | 1.3.6.1.4.1.353.5.7.1.1.10.1.5 | Gauge32 | read-only | current |
| imaLinkCurrentFeUnavailSecs OBJECT-TYPE Count of unavailable seconds at far-end in the current 15 minute interval: unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE. | 1.3.6.1.4.1.353.5.7.1.1.10.1.6 | Gauge32 | read-only | current |
| imaLinkCurrentNeTxUnusableSecs OBJECT-TYPE Tx Unusable seconds: count of Unusable seconds at the near-end Tx LSM in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.7 | Gauge32 | read-only | current |
| imaLinkCurrentNeRxUnusableSecs OBJECT-TYPE Rx Unusable seconds: count of Unusable seconds at the near-end Rx LSM in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.8 | Gauge32 | read-only | current |
| imaLinkCurrentFeTxUnusableSecs OBJECT-TYPE Tx Unusable seconds at far-end: count of seconds with Tx Unusable indications from the far-end Tx LSM in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.9 | Gauge32 | read-only | current |
| imaLinkCurrentFeRxUnusableSecs OBJECT-TYPE Rx Unusable seconds at far-end: count of seconds with Rx Unusable indications from the far-end Rx LSM in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.10 | Gauge32 | read-only | current |
| imaLinkCurrentNeTxNumFailures OBJECT-TYPE The number of times a near-end transmit failure alarm condition has been entered on this link (i.e., some form of implementation specific transmit fault) in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.11 | Gauge32 | read-only | current |
| imaLinkCurrentNeRxNumFailures OBJECT-TYPE The number of times a near-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, RFI-IMA, Mis-Connected, or some form of implementation specific receive fault) in the current 15 minute interval. | 1.3.6.1.4.1.353.5.7.1.1.10.1.12 | Gauge32 | read-only | current |
| imaLinkCurrentFeTxNumFailures OBJECT-TYPE The number of times a far-end transmit failure alarm condition has been entered on this link (i.e., Tx-Unusable-FE) in the current 15 minute interval. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.10.1.13 | Gauge32 | read-only | current |
| imaLinkCurrentFeRxNumFailures OBJECT-TYPE The number of times a far-end receive failure alarm condition has been entered on this link (i.e., Rx-Unusable-FE) in the current 15 minute interval. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.10.1.14 | Gauge32 | read-only | current |
| imaLinkCurrentTxStuffs OBJECT-TYPE Count of stuff events inserted in the transmit direction in the current 15 minute interval. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.10.1.15 | Gauge32 | read-only | current |
| imaLinkCurrentRxStuffs OBJECT-TYPE Count of stuff events detected in the receive direction in the current 15 minute interval. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.10.1.16 | Gauge32 | read-only | current |
| imaLinkIntervalTable OBJECT-TYPE The IMA Link Interval table. | 1.3.6.1.4.1.353.5.7.1.1.11 | not-accessible | current | |
| imaLinkIntervalEntry OBJECT-TYPE An entry in the IMA Link Interval table. | 1.3.6.1.4.1.353.5.7.1.1.11.1 | not-accessible | current | |
| imaLinkIntervalNumber OBJECT-TYPE A number between 1 and 96, where 1 is the most recently completed 15 minute interval and 96 is the least recently completed 15 minutes interval (assuming that all 96 intervals are valid). | 1.3.6.1.4.1.353.5.7.1.1.11.1.1 | INTEGER (1..96) | not-accessible | current |
| imaLinkIntervalImaViolations OBJECT-TYPE ICP violations: count of errored, invalid or missing ICP cells, except during SES-IMA or UAS-IMA conditions, in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.2 | Gauge32 | read-only | current |
| imaLinkIntervalOifAnomalies OBJECT-TYPE The number of OIF anomalies, except during SES-IMA or UAS-IMA conditions, at the near-end in one of the previous 96, individual 15 minute, intervals. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.11.1.3 | Gauge32 | read-only | current |
| imaLinkIntervalNeSevErroredSecs OBJECT-TYPE Count of one second intervals containing >= 30% of the ICP cells counted as IV-IMAs, or one or more link defects (e.g., LOS, OOF/LOF, AIS, or LCD), LIF defects, or LODS defects, except during UAS-IMA condition, in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.4 | Gauge32 | read-only | current |
| imaLinkIntervalFeSevErroredSecs OBJECT-TYPE Count of one second intervals containing one or more RDI-IMA defects, except during UAS-IMA-FE condition, in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.5 | Gauge32 | read-only | current |
| imaLinkIntervalNeUnavailSecs OBJECT-TYPE Count of unavailable seconds at near-end in one of the previous 96, individual 15 minute, intervals: unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA. | 1.3.6.1.4.1.353.5.7.1.1.11.1.6 | Gauge32 | read-only | current |
| imaLinkIntervalFeUnavailSecs OBJECT-TYPE Count of unavailable seconds at far-end in one of the previous 96, individual 15 minute, intervals: unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE. | 1.3.6.1.4.1.353.5.7.1.1.11.1.7 | Gauge32 | read-only | current |
| imaLinkIntervalNeTxUnusableSecs OBJECT-TYPE Tx Unusable seconds: count of Unusable seconds at the near-end Tx LSM in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.8 | Gauge32 | read-only | current |
| imaLinkIntervalNeRxUnusableSecs OBJECT-TYPE Rx Unusable seconds: count of Unusable seconds at the near-end Rx LSM in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.9 | Gauge32 | read-only | current |
| imaLinkIntervalFeTxUnusableSecs OBJECT-TYPE Tx Unusable seconds at far-end: count of seconds with Tx Unusable indications from the far-end Tx LSM in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.10 | Gauge32 | read-only | current |
| imaLinkIntervalFeRxUnusableSecs OBJECT-TYPE Rx Unusable seconds at far-end: count of seconds with Rx Unusable indications from the far-end Rx LSM in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.11 | Gauge32 | read-only | current |
| imaLinkIntervalNeTxNumFailures OBJECT-TYPE The number of times a near-end transmit failure alarm condition has been entered on this link (i.e., some form of implementation specific transmit fault) in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.12 | Gauge32 | read-only | current |
| imaLinkIntervalNeRxNumFailures OBJECT-TYPE The number of times a near-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, RFI-IMA, Mis-Connected, or some form of implementation specific receive fault) in one of the previous 96, individual 15 minute, intervals. | 1.3.6.1.4.1.353.5.7.1.1.11.1.13 | Gauge32 | read-only | current |
| imaLinkIntervalFeTxNumFailures OBJECT-TYPE The number of times a far-end transmit failure alarm condition has been entered on this link (i.e., Tx-Unusable-FE) in one of the previous 96, individual 15 minute, intervals. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.11.1.14 | Gauge32 | read-only | current |
| imaLinkIntervalFeRxNumFailures OBJECT-TYPE The number of times a far-end receive failure alarm condition has been entered on this link (i.e., Rx-Unusable-FE) in one of the previous 96, individual 15 minute, intervals. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.11.1.15 | Gauge32 | read-only | current |
| imaLinkIntervalTxStuffs OBJECT-TYPE Count of stuff events inserted in the transmit direction in one of the previous 96, individual 15 minute, intervals. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.11.1.16 | Gauge32 | read-only | current |
| imaLinkIntervalRxStuffs OBJECT-TYPE Count of stuff events detected in the receive direction in one of the previous 96, individual 15 minute, intervals. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.11.1.17 | Gauge32 | read-only | current |
| imaLinkTotalTable OBJECT-TYPE The IMA Link Total table. | 1.3.6.1.4.1.353.5.7.1.1.12 | not-accessible | current | |
| imaLinkTotalEntry OBJECT-TYPE An entry in the IMA Link Total table. | 1.3.6.1.4.1.353.5.7.1.1.12.1 | not-accessible | current | |
| imaLinkTotalImaViolations OBJECT-TYPE ICP violations: count of errored, invalid or missing ICP cells, except during SES-IMA or UAS-IMA conditions, in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.1 | Gauge32 | read-only | current |
| imaLinkTotalOifAnomalies OBJECT-TYPE The number of OIF anomalies, except during SES-IMA or UAS-IMA conditions, at the near-end in the previous 24 hour interval. Invalid 15 minute intervals count as 0. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.12.1.2 | Gauge32 | read-only | current |
| imaLinkTotalNeSevErroredSecs OBJECT-TYPE Count of one second intervals containing >= 30% of the ICP cells counted as IV-IMAs, or one or more link defects (e.g., LOS, OOF/LOF, AIS, or LCD), LIF defects, or LODS defects, except during UAS-IMA condition, in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.3 | Gauge32 | read-only | current |
| imaLinkTotalFeSevErroredSecs OBJECT-TYPE Count of one second intervals containing one or more RDI-IMA defects, except during UAS-IMA-FE condition, in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.4 | Gauge32 | read-only | current |
| imaLinkTotalNeUnavailSecs OBJECT-TYPE Count of unavailable seconds at near-end in the previous 24 hour interval: unavailability begins at the onset of 10 contiguous SES-IMA and ends at the onset of 10 contiguous seconds with no SES-IMA. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.5 | Gauge32 | read-only | current |
| imaLinkTotalFeUnavailSecs OBJECT-TYPE Count of unavailable seconds at far-end in the previous 24 hour interval: unavailability begins at the onset of 10 contiguous SES-IMA-FE and ends at the onset of 10 contiguous seconds with no SES-IMA-FE. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.6 | Gauge32 | read-only | current |
| imaLinkTotalNeTxUnusableSecs OBJECT-TYPE Tx Unusable seconds: count of Unusable seconds at the near-end Tx LSM in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.7 | Gauge32 | read-only | current |
| imaLinkTotalNeRxUnusableSecs OBJECT-TYPE Rx Unusable seconds: count of Unusable seconds at the near-end Rx LSM in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.8 | Gauge32 | read-only | current |
| imaLinkTotalFeTxUnusableSecs OBJECT-TYPE Tx Unusable seconds at far-end: count of seconds with Tx Unusable indications from the far-end Tx LSM in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.9 | Gauge32 | read-only | current |
| imaLinkTotalFeRxUnusableSecs OBJECT-TYPE Rx Unusable seconds at far-end: count of seconds with Rx Unusable indications from the far-end Rx LSM in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.10 | Gauge32 | read-only | current |
| imaLinkTotalNeTxNumFailures OBJECT-TYPE The number of times a near-end transmit failure alarm condition has been entered on this link (i.e., some form of implementation specific transmit fault) in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.11 | Gauge32 | read-only | current |
| imaLinkTotalNeRxNumFailures OBJECT-TYPE The number of times a near-end receive failure alarm condition has been entered on this link (i.e., LIF, LODS, RFI-IMA, Mis-Connected, or some form of implementation specific receive fault) in the previous 24 hour interval. Invalid 15 minute intervals count as 0. | 1.3.6.1.4.1.353.5.7.1.1.12.1.12 | Gauge32 | read-only | current |
| imaLinkTotalFeTxNumFailures OBJECT-TYPE The number of times a far-end transmit failure alarm condition has been entered on this link (i.e., Tx-Unusable-FE) in the previous 24 hour interval. Invalid 15 minute intervals count as 0. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.12.1.13 | Gauge32 | read-only | current |
| imaLinkTotalFeRxNumFailures OBJECT-TYPE The number of times a far-end receive failure alarm condition has been entered on this link (i.e., Rx-Unusable-FE) in the previous 24 hour interval. Invalid 15 minute intervals count as 0. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.12.1.14 | Gauge32 | read-only | current |
| imaLinkTotalTxStuffs OBJECT-TYPE Count of stuff events inserted in the transmit direction in the previous 24 hour interval. Invalid 15 minute intervals count as 0. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.12.1.15 | Gauge32 | read-only | current |
| imaLinkTotalRxStuffs OBJECT-TYPE Count of stuff events detected in the receive direction in the previous 24 hour interval. Invalid 15 minute intervals count as 0. This is an optional attribute. | 1.3.6.1.4.1.353.5.7.1.1.12.1.16 | Gauge32 | read-only | current |
| atmfImaMibTraps OBJECT-IDENTITY | 1.3.6.1.4.1.353.5.7.1.2 | |||
| atmfImaMibTrapPrefix OBJECT-IDENTITY | 1.3.6.1.4.1.353.5.7.1.2.0 | |||
| atmfImaMibConformance OBJECT-IDENTITY | 1.3.6.1.4.1.353.5.7.1.3 | |||
| atmfImaMibGroups OBJECT-IDENTITY | 1.3.6.1.4.1.353.5.7.1.3.1 | |||
| atmfImaMibCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.353.5.7.1.3.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| imaFailureAlarm NOTIFICATION-TYPE The imaFailureAlarm provides a method for an agent implementing IMA to notify an NMS of an alarm condition. | 1.3.6.1.4.1.353.5.7.1.2.0.1 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| imaGroupGroup OBJECT-GROUP A set of objects providing configuration and status information for an IMA group definition. | 1.3.6.1.4.1.353.5.7.1.3.1.1 | current |
| imaLinkGroup OBJECT-GROUP A set of objects providing status information for an IMA link. | 1.3.6.1.4.1.353.5.7.1.3.1.2 | current |
| imaGroupMappingTableGroup OBJECT-GROUP A table mapping the 'ifIndex' values of 'imaGroupIfIndex' to the 'imaGroupIndex' values of the corresponding IMA group. | 1.3.6.1.4.1.353.5.7.1.3.1.3 | current |
| imaTestPatternGroup OBJECT-GROUP Objects in the imaGroupTable and imaLinkTable which control and report on the Test Pattern Procedure. These objects must be implemented if the IMA Test Pattern Procedure is supported. | 1.3.6.1.4.1.353.5.7.1.3.1.4 | current |
| imaAlarmGroup OBJECT-GROUP Objects used in the imaFailureAlarm notification. | 1.3.6.1.4.1.353.5.7.1.3.1.5 | current |
| imaGroupIntervalGroup OBJECT-GROUP Objects containing interval statistics for an IMA group. | 1.3.6.1.4.1.353.5.7.1.3.1.6 | current |
| imaLinkIntervalGroup OBJECT-GROUP Objects containing interval statistics for an IMA link. | 1.3.6.1.4.1.353.5.7.1.3.1.7 | current |
| imaNotificationsGroup NOTIFICATION-GROUP Notifications that must be implemented for IMA groups and links. | 1.3.6.1.4.1.353.5.7.1.3.1.8 | current |
| atmfImaMibCompliance MODULE-COMPLIANCE The compliance statement for network elements implementing ATM Forum Inverse Multiplexing for ATM (IMA) interfaces. | 1.3.6.1.4.1.353.5.7.1.3.2.1 | current |