MIBs Depot

IEEE-802DOT17-RPR-MIB

Registered at
1.0.8802.17.1.1
Last updated
2004-04-21 12:00
Organization
IEEE 802.17 Working Group
Revisions
2004-04-21 12:00
Namespace
standard
Source file
IEEE-802DOT17-RPR-MIB
Digest
sha256:9f27fa4f456f034ca05abe22a7e5beaa8c9a60c783c6e2a4d31b7c84e7109fba

Description

The resilient packet ring MIB for IEEE 802.17. Copyright (C) IEEE802.17. This version of this MIB module is part of IEEE802.17; see the draft itself for full legal notices.

Contact

stds-802-17@ieee.org

Imports

FromSymbols
HC-PerfHist-TC-MIBHCPerfCurrentCount, HCPerfIntervalCount, HCPerfTotalCount
IF-MIBInterfaceIndex, InterfaceIndexOrZero
INET-ADDRESS-MIBInetAddress, InetAddressType
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter32, Counter64, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, TEXTUAL-CONVENTION, TimeStamp, TruthValue

Imported by

2 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

HC-PerfHist-TC-MIB
IANAifType-MIB
IEEE-802DOT17-RPR-MIB
IF-MIB
INET-ADDRESS-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
RprOamRinglet
TEXTUAL-CONVENTION
Indicates the ringlet on which the OAM action request/response is sent/replied. The valid values for this object are: (1) Default (2) ringlet0 (3) ringlet1 (4) Reverse ringlet. The value (4) is applicable only for OAM response action.
current
RprProtectionStatus
TEXTUAL-CONVENTION
Indicates the current protection status of the RPR MAC span. The status values are (arranged in ascending priority order) : noRequest No protection request on the span, the protection status is idle. waitToRestore The condition for an automatic protection was cleared and the span is engaged in a wait to restore period. manualSwitch A user initiated manual switch (via the rprSpanProtectionCommand) on the span. signalDegraded An automatically-detected status which causes protection on a span when a media signal degrade is detected due to excessive BER. signalFailed An automatically-detected status which causes protection on a span when a media signal failure is detected. forcedSwitch A user initiated forced switch (via the rprSpanProtectionCommand) on the span.
current
RprSpan
TEXTUAL-CONVENTION
Indicates the span interface of the RPR MAC. Each RPR span is connected to both ringlet0 and ringlet1. The east span receives from ringlet1 and transmits through ringlet0. The west span receives from ringlet0 and transmits through ringlet1.
current

Objects

NameOIDSyntaxAccessStatus
rprObjects
OBJECT-IDENTITY
1.0.8802.17.1.1.1
rprGeneral
OBJECT-IDENTITY
1.0.8802.17.1.1.1.1
rprIfTable
OBJECT-TYPE
The RPR interface table, extension to the ifTable. All read-write attributes in this table are non-volatile, i.e. will be retained across system reset.
1.0.8802.17.1.1.1.1.1not-accessiblecurrent
rprIfEntry
OBJECT-TYPE
One such entry for every interface in the ifTable which has an ifType of RPR interface.
1.0.8802.17.1.1.1.1.1.1not-accessiblecurrent
rprIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.1.1.1.1InterfaceIndexnot-accessiblecurrent
rprIfStationsOnRing
OBJECT-TYPE
The number of stations on the RPR ring. When the operStatus of the interface is down the value is 1.
1.0.8802.17.1.1.1.1.1.1.2Unsigned32 (1..255)read-onlycurrent
rprIfReversionMode
OBJECT-TYPE
The reversion mode of the MAC, False for non-revertive True for revertive. Revertive station will return to idle state after WTR interval expires. Default value for reversion mode is true.
1.0.8802.17.1.1.1.1.1.1.3TruthValueread-writecurrent
rprIfProtectionWTR
OBJECT-TYPE
Indicates the length of time in seconds, to remain in the protection state, after the cause of an automatic protection is removed. This mechanism prevents protection switch oscillations. Default value for WTR is 10 seconds.
1.0.8802.17.1.1.1.1.1.1.4Unsigned32 (0..1440)read-writecurrent
rprIfProtectionFastTimer
OBJECT-TYPE
Indicates the protection messages fast timer value in 1 ms units. The fast timer is used for protection protocols. Default value for fast timer protection messages is 10 ms.
1.0.8802.17.1.1.1.1.1.1.5Unsigned32 (1..20)read-writecurrent
rprIfProtectionSlowTimer
OBJECT-TYPE
Indicates the protection slow timer value in 50 ms units. The slow timer is used for topology and protection protocols. Default value for slow timer protection and topology messages is 20 units of 50 ms, i.e. 1sec.
1.0.8802.17.1.1.1.1.1.1.6Unsigned32 (1..200)read-writecurrent
rprIfAtdTimer
OBJECT-TYPE
Indicates the timer period for ATD message transmissions. Default value is 20 units of 50 ms, i.e. 1sec.
1.0.8802.17.1.1.1.1.1.1.7Unsigned32 (1..200)read-writecurrent
rprIfKeepaliveTimeout
OBJECT-TYPE
Indicates the timer to declare keepalive timeout, multiples of 1 millisecond. Default value for keepalive timeout is 3 ms.
1.0.8802.17.1.1.1.1.1.1.8Unsigned32 (2..50)read-writecurrent
rprIfFairnessAggressive
OBJECT-TYPE
Indicates whether the selected RPR fairness algorithm is aggressive or conservative. If true, the selected fairness mode is aggressive. If false, the selected fairness mode is conservative. The default value for fairness aggressive is true.
1.0.8802.17.1.1.1.1.1.1.9TruthValueread-writecurrent
rprIfPtqSize
OBJECT-TYPE
The size in bytes of the Primary Transit Queue per ringlet supported by this RPR MAC.
1.0.8802.17.1.1.1.1.1.1.10Unsigned32read-onlycurrent
rprIfStqSize
OBJECT-TYPE
The size in bytes of the Secondary Transit Queue per ringlet supported by this RPR MAC.
1.0.8802.17.1.1.1.1.1.1.11Unsigned32read-onlycurrent
rprIfSTQFullThreshold
OBJECT-TYPE
A level of STQ occupancy at or above which the STQ is almost full. This attribute specifies the full threshold location in MTU units below the STQ size. The range is [stqHighThreshold + mtuSize, sizeSTQ - mtuSize]. The default value for stqFullThreshold is sizeSTQ - 2*mtuSize.
1.0.8802.17.1.1.1.1.1.1.12Unsigned32read-writecurrent
rprIfIdleThreshold
OBJECT-TYPE
Indicates that a MAC is experiencing an adverse rate mismatch. When the PTQ depth exceeds this value, the incoming link is considered adversely rate mismatched. This attribute specifies the idle-threshold location from the top of the PTQ buffer, in MTU size. Default value should be 1, which means (sizePTQ - mtuSize)
1.0.8802.17.1.1.1.1.1.1.13Unsigned32read-writecurrent
rprIfSesThreshold
OBJECT-TYPE
Indicates the number of E-RPR errors to declare a second as SES-RPR The default value is the rounded integer of 0.000001 * (lineRate * advertisementRatio).
1.0.8802.17.1.1.1.1.1.1.14Unsigned32 (1..512)read-writecurrent
rprIfWrapConfig
OBJECT-TYPE
Indicates the configured protection mode, steering or wrapping, in a MAC that supports both modes. If wrap configured bit is set, the station will perform wrap protection during ring failures. If the station detects another station on the ring that has a protection configuration that conflicts with its own, the station will generate a defect to higher layers. Default value for wrap preferred is false for steering only stations, and true for stations that implement wrapping.
1.0.8802.17.1.1.1.1.1.1.15TruthValueread-writecurrent
rprIfJumboFramePreferred
OBJECT-TYPE
Indicates the preference of the manager to support jumbo frame in a MAC that supports jumbo frame. The station advertises the 'logical and' of rprIfJumboFramePreferred and jumbo capable bit in the rprIfMacCapability. Default value for jumbo frame preferred is true. i.e. station supports jumbo frame.
1.0.8802.17.1.1.1.1.1.1.16TruthValueread-writecurrent
rprIfMacOperModes
OBJECT-TYPE
The summary of the Mac operational modes. if strictOrder is set, the MAC operates in strict order mode. if dropBadFcs is set, frames with bad FCS are dropped.
1.0.8802.17.1.1.1.1.1.1.17Bits {strictOrder(0), dropBadFcs(1)}read-onlycurrent
rprIfRingOperModes
OBJECT-TYPE
The summary of the ring operational modes collected through the topology discovery protocol. If at least one station doesn't support jumbo frames, the jumboFrame bit in this attribute is set to false. Only if all stations support jumbo frames, the bit is true. If at least one station wasn't configured to wrap, the wrap bit in this attribute is set to false. Only if all stations configured to wrap, the bit is true. If the ring doesn't complete full loop, the ring is considered openRing, with at least one detected edge.
1.0.8802.17.1.1.1.1.1.1.18Bits {jumboFrames(0), wrapProtection(1), openRing(2)}read-onlycurrent
rprIfCurrentStatus
OBJECT-TYPE
Indicates the current status of the RPR interface. this attribute is used to generate alarm to the management system.
1.0.8802.17.1.1.1.1.1.1.19Bits {neighborInconsistency(0), duplicateMac(1), exceedMaxStations(2)}read-onlycurrent
rprIfLastChange
OBJECT-TYPE
The value of sysUpTime at the time when any of the following attributes changes: rprIfStationsOnRing, rprIfReversionMode, rprIfProtectionWTR, rprIfProtectionFastTimer, rprIfProtectionSlowTimer, rprIfAtdTimer, rprIfKeepaliveTimeout, rprIfFairnessAggressive, rprIfSTQFullThreshold, rprIfIdleThreshold, rprIfSesThreshold, rprIfWrapConfig, rprIfJumboFramePreferred, rprIfMacOperModes, rprIfRingOperModes, rprIfCurrentStatus contents of the rprTopoImageEntry.
1.0.8802.17.1.1.1.1.1.1.20TimeStampread-onlycurrent
rprIfChanges
OBJECT-TYPE
Indicates number of times rprIfLastChange changed. The discontinued counter value is indicated by the ifCounterDiscontinuityTime value.
1.0.8802.17.1.1.1.1.1.1.21Counter32read-onlycurrent
rprIfStatsControlTable
OBJECT-TYPE
The RPR statistics management table, controls the collection, duration, clearance, and status of the MAC statistics. The usage of this table is as follows: 1. In order to clear period of counters (or all periods) of specific counting point (or all counting points) of the RPR MAC, the user should first set the rprIfStatsControlPeriodClear item to specify the period that he would like to clear, and the rprIfStatsControlCountPointClear item to specify the counting point on which he would like to perform the statistics clearance. In case that the user specified 'clearSpecificInterval' in the rprIfStatsControlPeriodClear item, the user should also set the specific interval to clear by setting rprIfStatsControlIntervalClear. After setting these items, the user can activate the clear operation by setting rprIfStatsControlCommitClear item to 'commit'. The status of the clear operation (done of failed) is indicated by the returned value of rprIfStatsControlCommitClear item. 2. Setting rprIfStatsControlPeriodClear to 'clearAllIntervals' and rprIfStatsControlCountPointClear to 'clearWest' (for example) will clear all current and previous intervals, and day counters of the west side of the RPR MAC. 3. The IntervalValidData of cleared interval should be set to false. All read-write attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.1.2not-accessiblecurrent
rprIfStatsControlEntry
OBJECT-TYPE
One such entry for every interface in the ifTable which has an ifType of RPR interface.
1.0.8802.17.1.1.1.1.2.1not-accessiblecurrent
rprIfStatsControlIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.1.2.1.1InterfaceIndexnot-accessiblecurrent
rprIfStatsControlPeriodClear
OBJECT-TYPE
This attribute allows for some or all of the interval statistics for this RPR MAC to be cleared. It does not affect the values of the running counters or the counter values reported through the interface MIB. clearSpecificInterval clears the interval indicated by rprIfStatsControlIntervalClear. Default value for period clear is idle.
1.0.8802.17.1.1.1.1.2.1.2INTEGER {idle(1), clearAllIntervals(2), clearCurrent(3), clearIntervals(4), clearSpecificInterval(5)}read-writecurrent
rprIfStatsControlCountPointClear
OBJECT-TYPE
This attribute allows for a specific counting point of the RPR MAC or all of the RPR MAC counting points to be cleared on rprIfStatsControlPeriodClear request. Default value for Interface to clear is clearAll, i.e. clear statistics of all interfaces.
1.0.8802.17.1.1.1.1.2.1.3INTEGER {clearAll(1), clearWest(2), clearEast(3), clearClient(4)}read-writecurrent
rprIfStatsControlIntervalClear
OBJECT-TYPE
The statistics interval number to clear. The interval identified by 1 is the most recently completed 15 minute interval, and interval identified by N is the interval immediately preceding the one identified by N-1. Setting rprIfStatsControlPeriodClear to clearSpecificInterval will clear the interval that is indicated by this object.
1.0.8802.17.1.1.1.1.2.1.4Unsigned32 (1..96)read-writecurrent
rprIfStatsControlCommitClear
OBJECT-TYPE
Sends a commit with input parameters to specify the Period (rprIfStatsControlPeriodClear), count point (rprIfStatsControlCountPointClear) and specific interval (rprIfStatsControlIntervalClear) to clear. If the clear operation succeeds this attribute will have the value commitDone(2) when read. If the clear operation fails this attribute will have the value commitFailed(3) when read.
1.0.8802.17.1.1.1.1.2.1.5INTEGER {commit(1), commitDone(2), commitFailed(3)}read-writecurrent
rprIfStatsControlTimeElapsed
OBJECT-TYPE
The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement interval. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
1.0.8802.17.1.1.1.1.2.1.6Unsigned32 (0..899)read-onlycurrent
rprIfStatsControlValidIntervals
OBJECT-TYPE
The number of previous 15-minute intervals for which data was collected. An RPR interface must be capable of supporting at least n intervals. The minimum value of n is 4. The default of n is 32. The maximum value of n is 96. The value will be <n> unless the measurement was (re-)started within the last (<n>*15) minutes, in which case the value will be the number of complete 15 minute intervals for which the agent has at least some data. In certain cases (e.g., in the case where the agent is a proxy) it is possible that some intervals are unavailable. In this case, this interval is the maximum interval number for which data is available.
1.0.8802.17.1.1.1.1.2.1.7Unsigned32 (0..96)read-onlycurrent
rprSpanTable
OBJECT-TYPE
The RPR interface Span table. All read-write attributes in this table are non-volatile, i.e. will be retained across system reset.
1.0.8802.17.1.1.1.1.3not-accessiblecurrent
rprSpanEntry
OBJECT-TYPE
One such entry for every span of an RPR interface.
1.0.8802.17.1.1.1.1.3.1not-accessiblecurrent
rprSpanIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.1.3.1.1InterfaceIndexnot-accessiblecurrent
rprSpanId
OBJECT-TYPE
Indicates the span interface of the RPR MAC. Each RPR span is connected to both ringlet0 and ringlet1. The east span receives from ringlet1 and transmits through ringlet0. The west span receives from ringlet0 and transmits through ringlet1.
1.0.8802.17.1.1.1.1.3.1.2RprSpannot-accessiblecurrent
rprSpanLowerLayerIfIndex
OBJECT-TYPE
The ifIndex of interface which is below the RPR layer in this span. A value of zero indicates an interface index that has yet to be determined
1.0.8802.17.1.1.1.1.3.1.3InterfaceIndexOrZeroread-onlycurrent
rprSpanTotalRingletReservedRate
OBJECT-TYPE
The total reserved subclassA0 bandwidth on the ringlet. This variable is used by the fairness module to determine the total reclaimable bandwidth.
1.0.8802.17.1.1.1.1.3.1.4Unsigned32read-onlycurrent
rprSpanCurrentStatus
OBJECT-TYPE
Indicates the current status of the RPR span. this attribute is used to generate alarm to the management system.
1.0.8802.17.1.1.1.1.3.1.5Bits {keepAliveTimeout(0), miscabling(1), phyLinkDegrade(2), phyLinkFail(3)}read-onlycurrent
rprSpanLastChange
OBJECT-TYPE
The value of sysUpTime at the time when any of the following attributes changes: rprSpanCurrentStatus, rprSpanProtectionNeighborValid, rprSpanProtectionHoldOffTimer, rprSpanProtectionCommand, rprSpanProtectionCount.
1.0.8802.17.1.1.1.1.3.1.6TimeStampread-onlycurrent
rprSpanChanges
OBJECT-TYPE
Indicates number of times rprSpanLastChange changed. The discontinued counter value is indicated by the ifCounterDiscontinuityTime value.
1.0.8802.17.1.1.1.1.3.1.7Counter32read-onlycurrent
rprSpanProtectionTable
OBJECT-TYPE
The RPR interface Span protection management table. All read-write attributes in this table are non-volatile, i.e. will be retained across system reset.
1.0.8802.17.1.1.1.1.4not-accessiblecurrent
rprSpanProtectionEntry
OBJECT-TYPE
One such entry for every span of an RPR interface.
1.0.8802.17.1.1.1.1.4.1not-accessiblecurrent
rprSpanProtectionIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.1.4.1.1InterfaceIndexnot-accessiblecurrent
rprSpanProtectionSpan
OBJECT-TYPE
The Span for this entry.
1.0.8802.17.1.1.1.1.4.1.2RprSpannot-accessiblecurrent
rprSpanProtectionNeighborValid
OBJECT-TYPE
Indicates whether the neighbor address is active or former. true value for active, false for former
1.0.8802.17.1.1.1.1.4.1.3TruthValueread-onlycurrent
rprSpanProtectionHoldOffTimer
OBJECT-TYPE
The period that RPR gives to lower layer to perform protection, before it activates its protection mechanism. Default value of hold off timer is 0.
1.0.8802.17.1.1.1.1.4.1.4Unsigned32 (0..500)read-writecurrent
rprSpanProtectionCommand
OBJECT-TYPE
The protection mode requested by management for the local station that can affect the protection status of the RPR station, according to the set of rules describing the RPR protection. When read, this object returns the last command written unless it has been preempted, or idle if no command has been written to this interface span since initialization. There is no pending of commands, that is if a command has been preempted by a failure, when the failure clears the command is not executed. If the command cannot be executed because an equal or \ higher priority request is in effect, an error is returned. writing idle to a span that has no pending protection command, has no affect. An idle clears an active WTR state. The protection commands (arranged in ascending priority order) are: idle This command clears the protection for the specified interface span. This value should be returned by a read request when no protection command has been written to the object. manualSwitch A protection command on each end of a specified span. This command doesn't have precedence over automatic protection, and therefore it can't preempt an existing automatic protection request. forcedSwitch A command on each end of a specified span. This command has precedence over automatic protection, and therefore it can preempt an existing automatic protection request. Default value of protection command is idle.
1.0.8802.17.1.1.1.1.4.1.5INTEGER {idle(1), manualSwitch(2), forcedSwitch(3)}read-writecurrent
rprSpanProtectionCount
OBJECT-TYPE
The number of transitions from idle state to active protection state. The discontinued counter value is indicated by the ifCounterDiscontinuityTime value.
1.0.8802.17.1.1.1.1.4.1.6Counter32read-onlycurrent
rprSpanProtectionDuration
OBJECT-TYPE
The total amount of time protection was active on the span interface. The discontinued counter value is indicated by the ifCounterDiscontinuityTime value.
1.0.8802.17.1.1.1.1.4.1.7Counter32read-onlycurrent
rprSpanProtectionLastActivationTime
OBJECT-TYPE
The value of sysUpTime at the time of the last protection activation.
1.0.8802.17.1.1.1.1.4.1.8TimeStampread-onlycurrent
rprIfChangeSummaryObject
OBJECT-IDENTITY
1.0.8802.17.1.1.1.1.5
rprIfChangeSummaryNumInterfaces
OBJECT-TYPE
Number of RPR interfaces on this device.
1.0.8802.17.1.1.1.1.5.1Unsigned32read-onlycurrent
rprIfChangeSummaryIfLastChange
OBJECT-TYPE
Latest timestamp when any instance of rprIfLastChange changed.
1.0.8802.17.1.1.1.1.5.2TimeStampread-onlycurrent
rprIfChangeSummaryIfChanges
OBJECT-TYPE
Number of times any instance of rprIfChanges changed. The discontinued counter value is indicated by the ifCounterDiscontinuityTime value.
1.0.8802.17.1.1.1.1.5.3Counter32read-onlycurrent
rprIfChangeSummarySpanLastChange
OBJECT-TYPE
Latest timestamp when any instance of rprSpanLastChange changed.
1.0.8802.17.1.1.1.1.5.4TimeStampread-onlycurrent
rprIfChangeSummarySpanChanges
OBJECT-TYPE
Number of times any instance of rprSpanChanges changed. The discontinued counter value is indicated by the ifCounterDiscontinuityTime value.
1.0.8802.17.1.1.1.1.5.5Counter32read-onlycurrent
rprIfChangeSummaryFairnessLastChange
OBJECT-TYPE
Latest timestamp when any instance of rprFairnessLastChange changed.
1.0.8802.17.1.1.1.1.5.6TimeStampread-onlycurrent
rprIfChangeSummaryFairnessChanges
OBJECT-TYPE
Number of times any instance of rprFairnessChanges changed. The discontinued counter value is indicated by the ifCounterDiscontinuityTime value.
1.0.8802.17.1.1.1.1.5.7Counter32read-onlycurrent
rprProtocols
OBJECT-IDENTITY
1.0.8802.17.1.1.1.2
rprTopoImageTable
OBJECT-TYPE
A topology map that details the list of stations on the RPR ringlets. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.2.1not-accessiblecurrent
rprTopoImageEntry
OBJECT-TYPE
Each entry contains information specific to a particular station on the ring. The table has at least one entry for the station itself, this entry indicates zero hops on each ringlet.
1.0.8802.17.1.1.1.2.1.1not-accessiblecurrent
rprTopoImageIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.2.1.1.1InterfaceIndexnot-accessiblecurrent
rprTopoImageMacAddress
OBJECT-TYPE
The 48-bit MAC address of the station.
1.0.8802.17.1.1.1.2.1.1.2MacAddressnot-accessiblecurrent
rprTopoImageSecMacAddress1
OBJECT-TYPE
The 48-bit first secondary MAC address of the station. Default and unused value is FF:FF:FF:FF:FF:FF
1.0.8802.17.1.1.1.2.1.1.3MacAddressread-onlycurrent
rprTopoImageSecMacAddress2
OBJECT-TYPE
The 48-bit second secondary MAC address of the station. Default and unused value is FF:FF:FF:FF:FF:FF
1.0.8802.17.1.1.1.2.1.1.4MacAddressread-onlycurrent
rprTopoImageStationIfIndex
OBJECT-TYPE
The station ifIndex.
1.0.8802.17.1.1.1.2.1.1.5InterfaceIndexread-onlycurrent
rprTopoImageStationName
OBJECT-TYPE
The operator assigned station name.
1.0.8802.17.1.1.1.2.1.1.6SnmpAdminStringread-onlycurrent
rprTopoImageInetAddressType
OBJECT-TYPE
Denotes the address type of the station INET address It should be set to 'unknown' if station INET address is not known.
1.0.8802.17.1.1.1.2.1.1.7InetAddressTyperead-onlycurrent
rprTopoImageInetAddress
OBJECT-TYPE
This object contains the value of of the station IP (v4 or V6) address. The format of this address is specified by the value of the corresponding rprTopoImageInetAddressType object. If the address type is unknown, then this object contains the zero-length OCTET-STRING.
1.0.8802.17.1.1.1.2.1.1.8InetAddressread-onlycurrent
rprTopoImageCapability
OBJECT-TYPE
Indicates the capabilities that the MAC supports. jumboFrames - Indicates whether the MAC capable of receiving, transmitting and transiting jumbo frames. wrapProtection - Indicates whether the MAC configured to wrap protection. supportsConservativeFairness - indicates the MAC supports conservative fairness algorithm.
1.0.8802.17.1.1.1.2.1.1.9Bits {jumboFrames(0), wrapProtection(1), supportsConservativeFairness(2)}read-onlycurrent
rprTopoImageRinglet0Hops
OBJECT-TYPE
The number of hops to this station through ringlet0. The self station is indicated with zero hops. A non reachable station is indicated with -1 value.
1.0.8802.17.1.1.1.2.1.1.10Integer32read-onlycurrent
rprTopoImageRinglet0ReservedRate
OBJECT-TYPE
The amount of A0 traffic that this station adds on ringlet0, in Mb/s units.
1.0.8802.17.1.1.1.2.1.1.11Unsigned32read-onlycurrent
rprTopoImageRinglet1Hops
OBJECT-TYPE
The number of hops to this station through ringlet1. The self station is indicated with zero hops. A non reachable station is indicated with -1 value.
1.0.8802.17.1.1.1.2.1.1.12Integer32read-onlycurrent
rprTopoImageRinglet1ReservedRate
OBJECT-TYPE
The amount of A0 traffic that this station adds on ringlet1, in Mb/s units.
1.0.8802.17.1.1.1.2.1.1.13Unsigned32read-onlycurrent
rprTopoImageWestProtectionStatus
OBJECT-TYPE
The current protection status of the West span.
1.0.8802.17.1.1.1.2.1.1.14RprProtectionStatusread-onlycurrent
rprTopoImageWestWeight
OBJECT-TYPE
The weight of the station on the west span. used for weighted fairness.
1.0.8802.17.1.1.1.2.1.1.15Unsigned32 (1..255)read-onlycurrent
rprTopoImageEastProtectionStatus
OBJECT-TYPE
The current protection status of the east span.
1.0.8802.17.1.1.1.2.1.1.16RprProtectionStatusread-onlycurrent
rprTopoImageEastWeight
OBJECT-TYPE
The weight of the station on the east span. Used for weighted fairness.
1.0.8802.17.1.1.1.2.1.1.17Unsigned32 (1..255)read-onlycurrent
rprTopoImageStatus
OBJECT-TYPE
Status of the station, the reachability of station through ringlet0 and ringlet1, wrap active on the station spans, events of reception frames with bad FCS, events of reception multichoke fairness frames.
1.0.8802.17.1.1.1.2.1.1.18Bits {reachableRinglet0(0), reachableRinglet1(1), wrapActiveWest(2), wrapActiveEast(3), receivedBadFcs(4), receivedMultichokeFairness(5)}read-onlycurrent
rprFairnessTable
OBJECT-TYPE
A table of RPR Fairness per RPR span. All read-write attributes in this table are non-volatile, i.e. will be retained across system reset.
1.0.8802.17.1.1.1.2.2not-accessiblecurrent
rprFairnessEntry
OBJECT-TYPE
A fairness parameters for a particular ringlet of the an RPR interface.
1.0.8802.17.1.1.1.2.2.1not-accessiblecurrent
rprFairnessIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.2.2.1.1InterfaceIndexnot-accessiblecurrent
rprFairnessRinglet
OBJECT-TYPE
The ringlet for which this row contains information. ringlet0 is the transmission of the east span and the reception of the west span, ringlet1 is the transmission of the west span and the reception of the east span
1.0.8802.17.1.1.1.2.2.1.2INTEGER {ringlet0(1), ringlet1(2)}not-accessiblecurrent
rprFairnessRingletWeight
OBJECT-TYPE
Weight assigned to fairness to permit the scaling of fair rate values among stations on the ringlet. This allows one station to use a larger share of available capacity than another station without violating fairness principles. The allowed range is [1, 255]. The default value is 1.
1.0.8802.17.1.1.1.2.2.1.3Unsigned32 (1..255)read-writecurrent
rprFairnessReservedRate
OBJECT-TYPE
The amount of A0 traffic that this station adds that ringlet, in Mb/s units. Default value for A0 reserved rate is 0 Mb/s.
1.0.8802.17.1.1.1.2.2.1.4Unsigned32read-writecurrent
rprFairnessMaxAllowed
OBJECT-TYPE
The maximum value that the station is allowed to transmit local excess traffic to the ringlet. The default value is the physical ring rate.
1.0.8802.17.1.1.1.2.2.1.5Unsigned32read-writecurrent
rprFairnessAgeCoef
OBJECT-TYPE
The coefficient used by the aging procedure to specify the relative weights assigned to (a) the change in the value of a rate-counter during the most recent agingInterval and (b) the value of the rate-counter at the end of the previous agingInterval. The value is interpreted as 2 raised to the power specified by this attribute. The default value is 2, giving an aging coefficient of 2**2, or 4.
1.0.8802.17.1.1.1.2.2.1.6Unsigned32 (0..4)read-writecurrent
rprFairnessRampCoef
OBJECT-TYPE
The coefficient used for ramping a rate. The value is interpreted as 2 raised to the power specified by this attribute. The default value is 6, giving a low-pass coefficient of 2**6, or 64.
1.0.8802.17.1.1.1.2.2.1.7Unsigned32 (4..9)read-writecurrent
rprFairnessLpCoef
OBJECT-TYPE
The coefficient used by the low-pass filter procedure to specify the relative weights applied to (a) the increase in the rate-count value during the most recent agingInterval and (b) the previous low-pass filtered rate. The former is assigned a weight of 1 and the latter a weight of (lpCoef-1). The value is interpreted as 2 raised to the power specified by this attribute. The default value is 6, giving a low-pass coefficient of 2**6, or 64.
1.0.8802.17.1.1.1.2.2.1.8Unsigned32 (4..9)read-writecurrent
rprFairnessAdvertisementRatio
OBJECT-TYPE
The ratio between the link capacity reserved for fairness control messages and the total link capacity. Default value of fairness advertisement ratio is 5 units of 0.00025, i.e 0.00125.
1.0.8802.17.1.1.1.2.2.1.9Unsigned32 (1..40)read-writecurrent
rprFairnessMcffReportCoef
OBJECT-TYPE
Indicates the number of SCFF advertisingIntervals that elapse between the sending of successive MCFFs, This value allows the interval between sending MCFFs to be established as MCFF_reportingInterval = rprFairnessMcffReportCoef * SCFF_avertisingInterval. The default value is 10.
1.0.8802.17.1.1.1.2.2.1.10Unsigned32 (8..512)read-writecurrent
rprFairnessActiveWeightsCoef
OBJECT-TYPE
Indicates the number of agingIntervals that elapse between successive computations of activeWeights. This value allows the interval between computations of activeWeights to be established as activeWeightsInterval = activeWeightsCoef * agingInterval. The default value is 64.
1.0.8802.17.1.1.1.2.2.1.11Unsigned32 (8..512)read-writecurrent
rprFairnessSTQHighThreshold
OBJECT-TYPE
A level of STQ occupancy at or above which CSFE frames are no longer admitted. Defined only for a dual transit-queue implementation. This attribute specifies the high threshold location in percentage of the STQ size. The allowed range is [2*mtuSize, stqFullThreshold -mtuSize]. The default value is 0.25*stqFullThreshold.
1.0.8802.17.1.1.1.2.2.1.12Unsigned32 (0..1000)read-writecurrent
rprFairnessSTQMedThreshold
OBJECT-TYPE
A level of buffer occupancy in a dual-queue deployment, at or above which congestion on the outbound link is declared. This attribute specifies the medium threshold location in percentage of the STQ size. The allowed range is [stqLowThreshold + mtuSize, stqHighThreshold - mtuSize]. The default value is 0.5 * (stqHighThreshold + stqLowThreshold).
1.0.8802.17.1.1.1.2.2.1.13Unsigned32 (0..1000)read-writecurrent
rprFairnessSTQLowThreshold
OBJECT-TYPE
A level of STQ occupancy at or above which congestion on the outbound link is imminent. Defined only for dual transit-queue implementations. This attribute specifies the low threshold location in percentage of the STQ size. The range is [mtuSize, stqHighThreshold -mtuSize]. The default value is 0.5*stqHighThreshold.
1.0.8802.17.1.1.1.2.2.1.14Unsigned32 (0..1000)read-writecurrent
rprFairnessRateHighThreshold
OBJECT-TYPE
Rate at or above which congestion on the outbound link is declared. The range is [0.4 * unreservedRate, 0.99 * unreservedRate]. The default value is 0.95 * unreservedRate.
1.0.8802.17.1.1.1.2.2.1.15Unsigned32 (400..990)read-writecurrent
rprFairnessRateLowThreshold
OBJECT-TYPE
Rate at or above which congestion on the outbound link is imminent. The range is [0.5 * rateHighThreshold, 0.99 * rateHighThreshold]. The default value is 0.9 * rateHighThreshold
1.0.8802.17.1.1.1.2.2.1.16Unsigned32 (500..990)read-writecurrent
rprFairnessResetWaterMarks
OBJECT-TYPE
Write resetWaterMarks to this attribute to reset the STQ water marks to the current occupancy. Default value is idle
1.0.8802.17.1.1.1.2.2.1.17INTEGER {idle(1), resetWaterMarks(2)}read-writecurrent
rprFairnessSTQHighWaterMark
OBJECT-TYPE
The highest level of STQ occupancy since the last reset of this value, in percentage of the STQ size.
1.0.8802.17.1.1.1.2.2.1.18Unsigned32 (0..1000)read-onlycurrent
rprFairnessSTQLowWaterMark
OBJECT-TYPE
The lowest level of STQ occupancy since the last reset of this value, in percentage of the STQ size.
1.0.8802.17.1.1.1.2.2.1.19Unsigned32 (0..1000)read-onlycurrent
rprFairnessLastChange
OBJECT-TYPE
The value of sysUpTime at the time when any of the following attributes changes: rprFairnessRingletWeight, rprFairnessReservedRate, rprFairnessMaxAllowed, rprFairnessAgeCoef, rprFairnessRampCoef, rprFairnessLpCoef, rprFairnessAdvertisementRatio, rprFairnessSTQHighThreshold, rprFairnessSTQLowThreshold rprFairnessResetWaterMarks.
1.0.8802.17.1.1.1.2.2.1.20TimeStampread-onlycurrent
rprFairnessChanges
OBJECT-TYPE
Indicates number of times rprFairnessLastChange changed. The discontinued counter value is indicated by the ifCounterDiscontinuityTime value.
1.0.8802.17.1.1.1.2.2.1.21Counter32read-onlycurrent
rprOamTable
OBJECT-TYPE
A table of RPR OAM actions. The table is designed to support a one action at a time on an RPR interface. All read-write attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.2.3not-accessiblecurrent
rprOamEntry
OBJECT-TYPE
OAM Echo and Flush control for an RPR interface
1.0.8802.17.1.1.1.2.3.1not-accessiblecurrent
rprOamIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.2.3.1.1InterfaceIndexnot-accessiblecurrent
rprOamActionType
OBJECT-TYPE
The type of OAM action. The valid values for this object are: (1) echo (2) flush.
1.0.8802.17.1.1.1.2.3.1.2INTEGER {echo(1), flush(2)}read-writecurrent
rprOamDestAddress
OBJECT-TYPE
The 48-bit MAC address of the destination station of OAM session.
1.0.8802.17.1.1.1.2.3.1.3MacAddressread-writecurrent
rprOamRequestRinglet
OBJECT-TYPE
The ringlet ID on which the OAM request should be sent.
1.0.8802.17.1.1.1.2.3.1.4RprOamRingletread-writecurrent
rprOamResponseRinglet
OBJECT-TYPE
The ringlet ID on which the OAM response should be replied.
1.0.8802.17.1.1.1.2.3.1.5RprOamRingletread-writecurrent
rprOamClassOfService
OBJECT-TYPE
The class-of-service of OAM session frames
1.0.8802.17.1.1.1.2.3.1.6INTEGER {classA(1), classB(2), classC(3)}read-writecurrent
rprOamUserData
OBJECT-TYPE
The operator assigned user specific data.
1.0.8802.17.1.1.1.2.3.1.7OCTET STRING (SIZE(0..1024))read-writecurrent
rprOamProtected
OBJECT-TYPE
Indicates whether the OAM action should be protected. In a wrapping ring, If true, the WE (wrap eligible) bit of the OAM action frame is set to 1. Otherwise, the WE bit is set to 0. In steering ring, If true, in case of failure on the requested ringlet between the source and the destination stations, the OAM action frame will be steered to the alternative ringlet. Otherwise, the OAM action frame will be sent through the requested ringlet regardless of its protection state.
1.0.8802.17.1.1.1.2.3.1.8TruthValueread-writecurrent
rprOamRequestCount
OBJECT-TYPE
Indicates the number of OAM requests to send. Default value of OAM request action is 1.
1.0.8802.17.1.1.1.2.3.1.9Unsigned32 (0..65535)read-writecurrent
rprOamTimeout
OBJECT-TYPE
Indicates the timer to declare OAM action timeout, in 10usec units. Default value of OAM timeout is 500 units of 10usec (i.e. 5 ms)
1.0.8802.17.1.1.1.2.3.1.10Unsigned32 (1..10000)read-writecurrent
rprOamControl
OBJECT-TYPE
Control of an OAM action. The valid values for this object are: (1) idle (2) active (3) abort. Default value of OAM control is idle.
1.0.8802.17.1.1.1.2.3.1.11INTEGER {idle(1), active(2), abort(3)}read-writecurrent
rprOamResponseCount
OBJECT-TYPE
Indicates the number of OAM actions responses received.
1.0.8802.17.1.1.1.2.3.1.12Unsigned32 (0..65535)read-onlycurrent
rprOamAvResponseTime
OBJECT-TYPE
Average response time to receive the OAM reply.
1.0.8802.17.1.1.1.2.3.1.13Unsigned32 (0..65535)read-onlycurrent
rprOamResponseStatus
OBJECT-TYPE
Status of an OAM action. The valid values for this object are: (1) unknown (2) inProcess (3) error (4) success. The action status is success if at least 90% of the responses were received till timeout.
1.0.8802.17.1.1.1.2.3.1.14INTEGER {unknown(1), inProcess(2), error(3), success(4)}read-onlycurrent
rprSpanCounters
OBJECT-IDENTITY
1.0.8802.17.1.1.1.3
rprSpanCountersCurrentTable
OBJECT-TYPE
The RPR MAC Span interface current counters table. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.3.1not-accessiblecurrent
rprSpanCountersCurrentEntry
OBJECT-TYPE
Frames and octets statistics for the current interval for the RPR MAC Span interface. The corresponding instance of rprIfStatsControlTimeElapsed indicates the number of seconds which have elapsed so far in the current interval.
1.0.8802.17.1.1.1.3.1.1not-accessiblecurrent
rprSpanCurrentIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.3.1.1.1InterfaceIndexnot-accessiblecurrent
rprSpanCurrentSpan
OBJECT-TYPE
An indication of the span of the interface for which this row contains information.
1.0.8802.17.1.1.1.3.1.1.2RprSpannot-accessiblecurrent
rprSpanCurrentInUcastClassAFrames
OBJECT-TYPE
The number of received (PHY to MAC) classA unicast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.3HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInUcastClassAOctets
OBJECT-TYPE
The number of received (PHY to MAC) classA unicast octets, in the current interval.
1.0.8802.17.1.1.1.3.1.1.4HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInUcastClassBCirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR unicast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.5HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInUcastClassBCirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR unicast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.6HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInUcastClassBEirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR unicast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.7HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInUcastClassBEirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR unicast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.8HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInUcastClassCFrames
OBJECT-TYPE
The number of received (PHY to MAC) classC unicast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.9HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInUcastClassCOctets
OBJECT-TYPE
The number of received (PHY to MAC) classC unicast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.10HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInMcastClassAFrames
OBJECT-TYPE
The number of received (PHY to MAC) classA multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.11HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInMcastClassAOctets
OBJECT-TYPE
The number of received (PHY to MAC) classA multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.12HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInMcastClassBCirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.13HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInMcastClassBCirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.14HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInMcastClassBEirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.15HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInMcastClassBEirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.16HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInMcastClassCFrames
OBJECT-TYPE
The number of received (PHY to MAC) classC multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.17HCPerfCurrentCountread-onlycurrent
rprSpanCurrentInMcastClassCOctets
OBJECT-TYPE
The number of received (PHY to MAC) classC multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.18HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutUcastClassAFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA unicast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.19HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutUcastClassAOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA unicast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.20HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutUcastClassBCirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR unicast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.21HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutUcastClassBCirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR unicast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.22HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutUcastClassBEirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR unicast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.23HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutUcastClassBEirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR unicast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.24HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutUcastClassCFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC unicast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.25HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutUcastClassCOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC unicast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.26HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutMcastClassAFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.27HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutMcastClassAOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.28HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutMcastClassBCirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.29HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutMcastClassBCirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.30HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutMcastClassBEirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.31HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutMcastClassBEirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.32HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutMcastClassCFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.3.1.1.33HCPerfCurrentCountread-onlycurrent
rprSpanCurrentOutMcastClassCOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.3.1.1.34HCPerfCurrentCountread-onlycurrent
rprSpanCountersIntervalTable
OBJECT-TYPE
The RPR MAC Span interface interval counters table. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.3.2not-accessiblecurrent
rprSpanCountersIntervalEntry
OBJECT-TYPE
Frames and octets statistics collected for a particular interval for the RPR MAC Span interface of a particular span of a particular RPR interface. The corresponding instance of rprIfValidIntervals indicates the number of intervals for which the set of statistics is available.
1.0.8802.17.1.1.1.3.2.1not-accessiblecurrent
rprSpanIntervalIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.3.2.1.1InterfaceIndexnot-accessiblecurrent
rprSpanIntervalSpan
OBJECT-TYPE
An indication of the span of the interface for which this row contains information.
1.0.8802.17.1.1.1.3.2.1.2RprSpannot-accessiblecurrent
rprSpanIntervalNumber
OBJECT-TYPE
A number between 1 and 96, which identifies the intervals for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and interval identified by N is the interval immediately preceding the one identified by N-1.
1.0.8802.17.1.1.1.3.2.1.3Unsigned32 (1..96)not-accessiblecurrent
rprSpanIntervalValidData
OBJECT-TYPE
This variable indicates if the data for this interval is valid. It will be valid if it contains data for 900 seconds plus or minus 10 seconds.
1.0.8802.17.1.1.1.3.2.1.4TruthValueread-onlycurrent
rprSpanIntervalTimeElapsed
OBJECT-TYPE
The duration of a particular interval in seconds. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
1.0.8802.17.1.1.1.3.2.1.5Unsigned32 (0..899)read-onlycurrent
rprSpanIntervalStartTime
OBJECT-TYPE
Indicates the wall clock time that this interval started.
1.0.8802.17.1.1.1.3.2.1.6DateAndTimeread-onlycurrent
rprSpanIntervalInUcastClassAFrames
OBJECT-TYPE
The number of received (PHY to MAC) classA unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.7HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInUcastClassAOctets
OBJECT-TYPE
The number of received (PHY to MAC) classA unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.8HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInUcastClassBCirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.9HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInUcastClassBCirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.10HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInUcastClassBEirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.11HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInUcastClassBEirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.12HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInUcastClassCFrames
OBJECT-TYPE
The number of received (PHY to MAC) classC unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.13HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInUcastClassCOctets
OBJECT-TYPE
The number of received (PHY to MAC) classC unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.14HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInMcastClassAFrames
OBJECT-TYPE
The number of received (PHY to MAC) classA multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.15HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInMcastClassAOctets
OBJECT-TYPE
The number of received (PHY to MAC) classA multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.16HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInMcastClassBCirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.17HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInMcastClassBCirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.18HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInMcastClassBEirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.19HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInMcastClassBEirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.20HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInMcastClassCFrames
OBJECT-TYPE
The number of received (PHY to MAC) classC multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.21HCPerfIntervalCountread-onlycurrent
rprSpanIntervalInMcastClassCOctets
OBJECT-TYPE
The number of received (PHY to MAC) classC multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.22HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutUcastClassAFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.23HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutUcastClassAOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.24HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutUcastClassBCirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR unicast frames, in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.25HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutUcastClassBCirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.26HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutUcastClassBEirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.27HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutUcastClassBEirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.28HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutUcastClassCFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.29HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutUcastClassCOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.30HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutMcastClassAFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.31HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutMcastClassAOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.32HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutMcastClassBCirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.33HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutMcastClassBCirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.34HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutMcastClassBEirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.35HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutMcastClassBEirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.36HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutMcastClassCFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.37HCPerfIntervalCountread-onlycurrent
rprSpanIntervalOutMcastClassCOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.3.2.1.38HCPerfIntervalCountread-onlycurrent
rprSpanCountersDayTable
OBJECT-TYPE
The RPR Mac Span Day Table contains the cumulative sum of the various statistics for the 24 hour period preceding the current interval. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.3.3not-accessiblecurrent
rprSpanCountersDayEntry
OBJECT-TYPE
An entry in the RPR Span Day table.
1.0.8802.17.1.1.1.3.3.1not-accessiblecurrent
rprSpanDayIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.3.3.1.1InterfaceIndexnot-accessiblecurrent
rprSpanDaySpan
OBJECT-TYPE
An indication of the span of the interface for which this row contains information.
1.0.8802.17.1.1.1.3.3.1.2RprSpannot-accessiblecurrent
rprSpanDayInUcastClassAFrames
OBJECT-TYPE
The number of received (PHY to MAC) classA unicast frames.
1.0.8802.17.1.1.1.3.3.1.3HCPerfTotalCountread-onlycurrent
rprSpanDayInUcastClassAOctets
OBJECT-TYPE
The number of received (PHY to MAC) classA unicast octets.
1.0.8802.17.1.1.1.3.3.1.4HCPerfTotalCountread-onlycurrent
rprSpanDayInUcastClassBCirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR unicast frames.
1.0.8802.17.1.1.1.3.3.1.5HCPerfTotalCountread-onlycurrent
rprSpanDayInUcastClassBCirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR unicast octets.
1.0.8802.17.1.1.1.3.3.1.6HCPerfTotalCountread-onlycurrent
rprSpanDayInUcastClassBEirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR unicast frames.
1.0.8802.17.1.1.1.3.3.1.7HCPerfTotalCountread-onlycurrent
rprSpanDayInUcastClassBEirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR unicast octets.
1.0.8802.17.1.1.1.3.3.1.8HCPerfTotalCountread-onlycurrent
rprSpanDayInUcastClassCFrames
OBJECT-TYPE
The number of received (PHY to MAC) classC unicast frames.
1.0.8802.17.1.1.1.3.3.1.9HCPerfTotalCountread-onlycurrent
rprSpanDayInUcastClassCOctets
OBJECT-TYPE
The number of received (PHY to MAC) classC unicast octets.
1.0.8802.17.1.1.1.3.3.1.10HCPerfTotalCountread-onlycurrent
rprSpanDayInMcastClassAFrames
OBJECT-TYPE
The number of received (PHY to MAC) classA multicast and broadcast frames
1.0.8802.17.1.1.1.3.3.1.11HCPerfTotalCountread-onlycurrent
rprSpanDayInMcastClassAOctets
OBJECT-TYPE
The number of received (PHY to MAC) classA multicast and broadcast octets
1.0.8802.17.1.1.1.3.3.1.12HCPerfTotalCountread-onlycurrent
rprSpanDayInMcastClassBCirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR multicast and broadcast frames
1.0.8802.17.1.1.1.3.3.1.13HCPerfTotalCountread-onlycurrent
rprSpanDayInMcastClassBCirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR multicast and broadcast octets
1.0.8802.17.1.1.1.3.3.1.14HCPerfTotalCountread-onlycurrent
rprSpanDayInMcastClassBEirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR multicast and broadcast frames
1.0.8802.17.1.1.1.3.3.1.15HCPerfTotalCountread-onlycurrent
rprSpanDayInMcastClassBEirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR multicast and broadcast octets
1.0.8802.17.1.1.1.3.3.1.16HCPerfTotalCountread-onlycurrent
rprSpanDayInMcastClassCFrames
OBJECT-TYPE
The number of received (PHY to MAC) classC multicast and broadcast frames
1.0.8802.17.1.1.1.3.3.1.17HCPerfTotalCountread-onlycurrent
rprSpanDayInMcastClassCOctets
OBJECT-TYPE
The number of received (PHY to MAC) classC multicast and broadcast octets
1.0.8802.17.1.1.1.3.3.1.18HCPerfTotalCountread-onlycurrent
rprSpanDayOutUcastClassAFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA unicast frames.
1.0.8802.17.1.1.1.3.3.1.19HCPerfTotalCountread-onlycurrent
rprSpanDayOutUcastClassAOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA unicast octets.
1.0.8802.17.1.1.1.3.3.1.20HCPerfTotalCountread-onlycurrent
rprSpanDayOutUcastClassBCirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR unicast frames.
1.0.8802.17.1.1.1.3.3.1.21HCPerfTotalCountread-onlycurrent
rprSpanDayOutUcastClassBCirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR unicast octets.
1.0.8802.17.1.1.1.3.3.1.22HCPerfTotalCountread-onlycurrent
rprSpanDayOutUcastClassBEirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR unicast frames
1.0.8802.17.1.1.1.3.3.1.23HCPerfTotalCountread-onlycurrent
rprSpanDayOutUcastClassBEirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR unicast octets
1.0.8802.17.1.1.1.3.3.1.24HCPerfTotalCountread-onlycurrent
rprSpanDayOutUcastClassCFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC unicast frames
1.0.8802.17.1.1.1.3.3.1.25HCPerfTotalCountread-onlycurrent
rprSpanDayOutUcastClassCOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC unicast octets
1.0.8802.17.1.1.1.3.3.1.26HCPerfTotalCountread-onlycurrent
rprSpanDayOutMcastClassAFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA multicast and broadcast frames.
1.0.8802.17.1.1.1.3.3.1.27HCPerfTotalCountread-onlycurrent
rprSpanDayOutMcastClassAOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA multicast and broadcast octets.
1.0.8802.17.1.1.1.3.3.1.28HCPerfTotalCountread-onlycurrent
rprSpanDayOutMcastClassBCirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR multicast and broadcast frames.
1.0.8802.17.1.1.1.3.3.1.29HCPerfTotalCountread-onlycurrent
rprSpanDayOutMcastClassBCirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR multicast and broadcast octets.
1.0.8802.17.1.1.1.3.3.1.30HCPerfTotalCountread-onlycurrent
rprSpanDayOutMcastClassBEirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR multicast and broadcast frames.
1.0.8802.17.1.1.1.3.3.1.31HCPerfTotalCountread-onlycurrent
rprSpanDayOutMcastClassBEirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR multicast and broadcast octets.
1.0.8802.17.1.1.1.3.3.1.32HCPerfTotalCountread-onlycurrent
rprSpanDayOutMcastClassCFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC multicast and broadcast frames.
1.0.8802.17.1.1.1.3.3.1.33HCPerfTotalCountread-onlycurrent
rprSpanDayOutMcastClassCOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC multicast and broadcast octets.
1.0.8802.17.1.1.1.3.3.1.34HCPerfTotalCountread-onlycurrent
rprSpanCountersStatsTable
OBJECT-TYPE
The RPR Mac Span interface total counters table. The DiscontinuityTime for this table is indicated by ifCounterDiscontinuityTime defined in ifXTable. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.3.4not-accessiblecurrent
rprSpanCountersStatsEntry
OBJECT-TYPE
An entry in the span stats table.
1.0.8802.17.1.1.1.3.4.1not-accessiblecurrent
rprSpanStatsIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.3.4.1.1InterfaceIndexnot-accessiblecurrent
rprSpanStatsSpan
OBJECT-TYPE
An indication of the span of the interface for which this row contains information.
1.0.8802.17.1.1.1.3.4.1.2RprSpannot-accessiblecurrent
rprSpanStatsInUcastClassAFrames
OBJECT-TYPE
The number of received (PHY to MAC) classA unicast frames.
1.0.8802.17.1.1.1.3.4.1.3Counter64read-onlycurrent
rprSpanStatsInUcastClassAOctets
OBJECT-TYPE
The number of received (PHY to MAC) classA unicast octets.
1.0.8802.17.1.1.1.3.4.1.4Counter64read-onlycurrent
rprSpanStatsInUcastClassBCirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR unicast frames.
1.0.8802.17.1.1.1.3.4.1.5Counter64read-onlycurrent
rprSpanStatsInUcastClassBCirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR unicast octets.
1.0.8802.17.1.1.1.3.4.1.6Counter64read-onlycurrent
rprSpanStatsInUcastClassBEirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR unicast frames.
1.0.8802.17.1.1.1.3.4.1.7Counter64read-onlycurrent
rprSpanStatsInUcastClassBEirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR unicast octets.
1.0.8802.17.1.1.1.3.4.1.8Counter64read-onlycurrent
rprSpanStatsInUcastClassCFrames
OBJECT-TYPE
The number of received (PHY to MAC) classC unicast frames.
1.0.8802.17.1.1.1.3.4.1.9Counter64read-onlycurrent
rprSpanStatsInUcastClassCOctets
OBJECT-TYPE
The number of received (PHY to MAC) classC unicast octets.
1.0.8802.17.1.1.1.3.4.1.10Counter64read-onlycurrent
rprSpanStatsInMcastClassAFrames
OBJECT-TYPE
The number of received (PHY to MAC) classA multicast and broadcast frames
1.0.8802.17.1.1.1.3.4.1.11Counter64read-onlycurrent
rprSpanStatsInMcastClassAOctets
OBJECT-TYPE
The number of received (PHY to MAC) classA multicast and broadcast octets
1.0.8802.17.1.1.1.3.4.1.12Counter64read-onlycurrent
rprSpanStatsInMcastClassBCirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR multicast and broadcast frames
1.0.8802.17.1.1.1.3.4.1.13Counter64read-onlycurrent
rprSpanStatsInMcastClassBCirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB CIR multicast and broadcast octets
1.0.8802.17.1.1.1.3.4.1.14Counter64read-onlycurrent
rprSpanStatsInMcastClassBEirFrames
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR multicast and broadcast frames
1.0.8802.17.1.1.1.3.4.1.15Counter64read-onlycurrent
rprSpanStatsInMcastClassBEirOctets
OBJECT-TYPE
The number of received (PHY to MAC) classB EIR multicast and broadcast octets
1.0.8802.17.1.1.1.3.4.1.16Counter64read-onlycurrent
rprSpanStatsInMcastClassCFrames
OBJECT-TYPE
The number of received (PHY to MAC) classC multicast and broadcast frames
1.0.8802.17.1.1.1.3.4.1.17Counter64read-onlycurrent
rprSpanStatsInMcastClassCOctets
OBJECT-TYPE
The number of received (PHY to MAC) classC multicast and broadcast octets
1.0.8802.17.1.1.1.3.4.1.18Counter64read-onlycurrent
rprSpanStatsInCtrlFrames
OBJECT-TYPE
The number of received (PHY to MAC) control frames processed by this MAC. This does not include control frames in transit, i.e. a multicast control frame received from a ringlet will be counted as In but not Out. This does not include Fairness or idle frames.
1.0.8802.17.1.1.1.3.4.1.19Counter64read-onlycurrent
rprSpanStatsInOamEchoFrames
OBJECT-TYPE
The number of received (PHY to MAC) OAM echo frames processed by this MAC.
1.0.8802.17.1.1.1.3.4.1.20Counter64read-onlycurrent
rprSpanStatsInOamFlushFrames
OBJECT-TYPE
The number of received (PHY to MAC) OAM flush frames processed by this MAC.
1.0.8802.17.1.1.1.3.4.1.21Counter64read-onlycurrent
rprSpanStatsInOamOrgFrames
OBJECT-TYPE
The number of received (PHY to MAC) OAM Org frames processed by this MAC.
1.0.8802.17.1.1.1.3.4.1.22Counter64read-onlycurrent
rprSpanStatsInTopoAtdFrames
OBJECT-TYPE
The number of received (PHY to MAC) Topology ATD frames processed by this MAC.
1.0.8802.17.1.1.1.3.4.1.23Counter64read-onlycurrent
rprSpanStatsInTopoChkSumFrames
OBJECT-TYPE
The number of received (PHY to MAC) topology checksum frames processed by this MAC.
1.0.8802.17.1.1.1.3.4.1.24Counter64read-onlycurrent
rprSpanStatsInTopoTpFrames
OBJECT-TYPE
The number of received (PHY to MAC) topology TP frames processed by this MAC.
1.0.8802.17.1.1.1.3.4.1.25Counter64read-onlycurrent
rprSpanStatsOutUcastClassAFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA unicast frames.
1.0.8802.17.1.1.1.3.4.1.26Counter64read-onlycurrent
rprSpanStatsOutUcastClassAOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA unicast octets.
1.0.8802.17.1.1.1.3.4.1.27Counter64read-onlycurrent
rprSpanStatsOutUcastClassBCirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR unicast frames.
1.0.8802.17.1.1.1.3.4.1.28Counter64read-onlycurrent
rprSpanStatsOutUcastClassBCirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR unicast octets.
1.0.8802.17.1.1.1.3.4.1.29Counter64read-onlycurrent
rprSpanStatsOutUcastClassBEirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR unicast frames
1.0.8802.17.1.1.1.3.4.1.30Counter64read-onlycurrent
rprSpanStatsOutUcastClassBEirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR unicast octets
1.0.8802.17.1.1.1.3.4.1.31Counter64read-onlycurrent
rprSpanStatsOutUcastClassCFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC unicast frames
1.0.8802.17.1.1.1.3.4.1.32Counter64read-onlycurrent
rprSpanStatsOutUcastClassCOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC unicast octets
1.0.8802.17.1.1.1.3.4.1.33Counter64read-onlycurrent
rprSpanStatsOutMcastClassAFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA multicast and broadcast frames.
1.0.8802.17.1.1.1.3.4.1.34Counter64read-onlycurrent
rprSpanStatsOutMcastClassAOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classA multicast and broadcast octets.
1.0.8802.17.1.1.1.3.4.1.35Counter64read-onlycurrent
rprSpanStatsOutMcastClassBCirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR multicast and broadcast frames.
1.0.8802.17.1.1.1.3.4.1.36Counter64read-onlycurrent
rprSpanStatsOutMcastClassBCirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB CIR multicast and broadcast octets.
1.0.8802.17.1.1.1.3.4.1.37Counter64read-onlycurrent
rprSpanStatsOutMcastClassBEirFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR multicast and broadcast frames.
1.0.8802.17.1.1.1.3.4.1.38Counter64read-onlycurrent
rprSpanStatsOutMcastClassBEirOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classB EIR multicast and broadcast octets.
1.0.8802.17.1.1.1.3.4.1.39Counter64read-onlycurrent
rprSpanStatsOutMcastClassCFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC multicast and broadcast frames.
1.0.8802.17.1.1.1.3.4.1.40Counter64read-onlycurrent
rprSpanStatsOutMcastClassCOctets
OBJECT-TYPE
The number of transmitted (MAC to PHY) classC multicast and broadcast octets.
1.0.8802.17.1.1.1.3.4.1.41Counter64read-onlycurrent
rprSpanStatsOutCtrlFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) control frames generated by this MAC. This does not include control frames in transit, i.e. a multicast control frame received from a ringlet will be counted as In but not Out. This does not include Fairness or idle frames.
1.0.8802.17.1.1.1.3.4.1.42Counter64read-onlycurrent
rprSpanStatsOutOamEchoFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) OAM echo frames generated by this MAC.
1.0.8802.17.1.1.1.3.4.1.43Counter64read-onlycurrent
rprSpanStatsOutOamFlushFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) OAM flush frames generated by this MAC.
1.0.8802.17.1.1.1.3.4.1.44Counter64read-onlycurrent
rprSpanStatsOutOamOrgFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) OAM Org frames generated by this MAC.
1.0.8802.17.1.1.1.3.4.1.45Counter64read-onlycurrent
rprSpanStatsOutTopoAtdFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) topology ATD frames generated by this MAC.
1.0.8802.17.1.1.1.3.4.1.46Counter64read-onlycurrent
rprSpanStatsOutTopoChkSumFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) topology checksum frames generated by this MAC.
1.0.8802.17.1.1.1.3.4.1.47Counter64read-onlycurrent
rprSpanStatsOutTopoTpFrames
OBJECT-TYPE
The number of transmitted (MAC to PHY) topology TP frames generated by this MAC.
1.0.8802.17.1.1.1.3.4.1.48Counter64read-onlycurrent
rprClientCounters
OBJECT-IDENTITY
1.0.8802.17.1.1.1.4
rprClientCountersCurrentTable
OBJECT-TYPE
The local station traffic current counters table. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.4.1not-accessiblecurrent
rprClientCountersCurrentEntry
OBJECT-TYPE
Frames and octets statistics for the current interval for the local station traffic of a particular RPR client interface. The corresponding instance of rprIfTimeElapsed indicates the number of seconds which have elapsed so far in the current interval.
1.0.8802.17.1.1.1.4.1.1not-accessiblecurrent
rprClientCurrentIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.4.1.1.1InterfaceIndexnot-accessiblecurrent
rprClientCurrentInUcastClassAFrames
OBJECT-TYPE
The number of MAC to client classA unicast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.2HCPerfCurrentCountread-onlycurrent
rprClientCurrentInUcastClassAOctets
OBJECT-TYPE
The number of MAC to client classA unicast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.3HCPerfCurrentCountread-onlycurrent
rprClientCurrentInUcastClassBCirFrames
OBJECT-TYPE
The number of MAC to client classB CIR unicast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.4HCPerfCurrentCountread-onlycurrent
rprClientCurrentInUcastClassBCirOctets
OBJECT-TYPE
The number of MAC to client classB CIR unicast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.5HCPerfCurrentCountread-onlycurrent
rprClientCurrentInUcastClassBEirFrames
OBJECT-TYPE
The number of MAC to client classB EIR unicast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.6HCPerfCurrentCountread-onlycurrent
rprClientCurrentInUcastClassBEirOctets
OBJECT-TYPE
The number of MAC to client classB EIR unicast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.7HCPerfCurrentCountread-onlycurrent
rprClientCurrentInUcastClassCFrames
OBJECT-TYPE
The number of MAC to client classC unicast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.8HCPerfCurrentCountread-onlycurrent
rprClientCurrentInUcastClassCOctets
OBJECT-TYPE
The number of MAC to client classC unicast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.9HCPerfCurrentCountread-onlycurrent
rprClientCurrentInMcastClassAFrames
OBJECT-TYPE
The number of MAC to client classA multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.10HCPerfCurrentCountread-onlycurrent
rprClientCurrentInMcastClassAOctets
OBJECT-TYPE
The number of MAC to client classA multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.11HCPerfCurrentCountread-onlycurrent
rprClientCurrentInMcastClassBCirFrames
OBJECT-TYPE
The number of MAC to client classB CIR multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.12HCPerfCurrentCountread-onlycurrent
rprClientCurrentInMcastClassBCirOctets
OBJECT-TYPE
The number of MAC to client classB CIR multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.13HCPerfCurrentCountread-onlycurrent
rprClientCurrentInMcastClassBEirFrames
OBJECT-TYPE
The number of MAC to client classB EIR multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.14HCPerfCurrentCountread-onlycurrent
rprClientCurrentInMcastClassBEirOctets
OBJECT-TYPE
The number of MAC to client classB EIR multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.15HCPerfCurrentCountread-onlycurrent
rprClientCurrentInMcastClassCFrames
OBJECT-TYPE
The number of MAC to client classC multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.16HCPerfCurrentCountread-onlycurrent
rprClientCurrentInMcastClassCOctets
OBJECT-TYPE
The number of MAC to client classC multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.17HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutUcastClassAFrames
OBJECT-TYPE
The number of client to MAC classA unicast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.18HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutUcastClassAOctets
OBJECT-TYPE
The number of client to MAC classA unicast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.19HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutUcastClassBCirFrames
OBJECT-TYPE
The number of client to MAC classB CIR unicast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.20HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutUcastClassBCirOctets
OBJECT-TYPE
The number of client to MAC classB CIR unicast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.21HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutUcastClassBEirFrames
OBJECT-TYPE
The number of client to MAC classB EIR unicast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.22HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutUcastClassBEirOctets
OBJECT-TYPE
The number of client to MAC classB EIR unicast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.23HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutUcastClassCFrames
OBJECT-TYPE
The number of client to MAC classC unicast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.24HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutUcastClassCOctets
OBJECT-TYPE
The number of client to MAC classC unicast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.25HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutMcastClassAFrames
OBJECT-TYPE
The number of client to MAC classA multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.26HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutMcastClassAOctets
OBJECT-TYPE
The number of client to MAC classA multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.27HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutMcastClassBCirFrames
OBJECT-TYPE
The number of client to MAC classB CIR multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.28HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutMcastClassBCirOctets
OBJECT-TYPE
The number of client to MAC classB CIR multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.29HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutMcastClassBEirFrames
OBJECT-TYPE
The number of client to MAC classB EIR multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.30HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutMcastClassBEirOctets
OBJECT-TYPE
The number of client to MAC classB EIR multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.31HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutMcastClassCFrames
OBJECT-TYPE
The number of client to MAC classC multicast and broadcast frames in the current interval.
1.0.8802.17.1.1.1.4.1.1.32HCPerfCurrentCountread-onlycurrent
rprClientCurrentOutMcastClassCOctets
OBJECT-TYPE
The number of client to MAC classC multicast and broadcast octets in the current interval.
1.0.8802.17.1.1.1.4.1.1.33HCPerfCurrentCountread-onlycurrent
rprClientCountersIntervalTable
OBJECT-TYPE
The local station traffic interval counters table. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.4.2not-accessiblecurrent
rprClientCountersIntervalEntry
OBJECT-TYPE
Frames and octets statistics collected for a particular interval for local station traffic of a particular RPR interface. The corresponding instance of rprIfValidIntervals indicates the number of intervals for which the set of statistics is available.
1.0.8802.17.1.1.1.4.2.1not-accessiblecurrent
rprClientIntervalIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.4.2.1.1InterfaceIndexnot-accessiblecurrent
rprClientIntervalNumber
OBJECT-TYPE
A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and interval identified by N is the interval immediately preceding the one identified by N-1.
1.0.8802.17.1.1.1.4.2.1.2Unsigned32 (1..96)not-accessiblecurrent
rprClientIntervalValidData
OBJECT-TYPE
This variable indicates if the data for this interval is valid. It will be valid if it contains data for 900 seconds plus or minus 10 seconds.
1.0.8802.17.1.1.1.4.2.1.3TruthValueread-onlycurrent
rprClientIntervalTimeElapsed
OBJECT-TYPE
The duration of a particular interval in seconds. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
1.0.8802.17.1.1.1.4.2.1.4Unsigned32 (0..899)read-onlycurrent
rprClientIntervalInUcastClassAFrames
OBJECT-TYPE
The number of MAC to client classA unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.5HCPerfIntervalCountread-onlycurrent
rprClientIntervalInUcastClassAOctets
OBJECT-TYPE
The number of MAC to client classA unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.6HCPerfIntervalCountread-onlycurrent
rprClientIntervalInUcastClassBCirFrames
OBJECT-TYPE
The number of MAC to client classB CIR unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.7HCPerfIntervalCountread-onlycurrent
rprClientIntervalInUcastClassBCirOctets
OBJECT-TYPE
The number of MAC to client classB CIR unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.8HCPerfIntervalCountread-onlycurrent
rprClientIntervalInUcastClassBEirFrames
OBJECT-TYPE
The number of MAC to client classB EIR unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.9HCPerfIntervalCountread-onlycurrent
rprClientIntervalInUcastClassBEirOctets
OBJECT-TYPE
The number of MAC to client classB EIR unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.10HCPerfIntervalCountread-onlycurrent
rprClientIntervalInUcastClassCFrames
OBJECT-TYPE
The number of MAC to client classC unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.11HCPerfIntervalCountread-onlycurrent
rprClientIntervalInUcastClassCOctets
OBJECT-TYPE
The number of MAC to client classC unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.12HCPerfIntervalCountread-onlycurrent
rprClientIntervalInMcastClassAFrames
OBJECT-TYPE
The number of MAC to client classA multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.13HCPerfIntervalCountread-onlycurrent
rprClientIntervalInMcastClassAOctets
OBJECT-TYPE
The number of MAC to client classA multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.14HCPerfIntervalCountread-onlycurrent
rprClientIntervalInMcastClassBCirFrames
OBJECT-TYPE
The number of MAC to client classB CIR multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.15HCPerfIntervalCountread-onlycurrent
rprClientIntervalInMcastClassBCirOctets
OBJECT-TYPE
The number of MAC to client classB CIR multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.16HCPerfIntervalCountread-onlycurrent
rprClientIntervalInMcastClassBEirFrames
OBJECT-TYPE
The number of MAC to client classB EIR multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.17HCPerfIntervalCountread-onlycurrent
rprClientIntervalInMcastClassBEirOctets
OBJECT-TYPE
The number of MAC to client classB EIR multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.18HCPerfIntervalCountread-onlycurrent
rprClientIntervalInMcastClassCFrames
OBJECT-TYPE
The number of MAC to client classC multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.19HCPerfIntervalCountread-onlycurrent
rprClientIntervalInMcastClassCOctets
OBJECT-TYPE
The number of MAC to client classC multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.20HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutUcastClassAFrames
OBJECT-TYPE
The number of client to MAC classA unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.21HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutUcastClassAOctets
OBJECT-TYPE
The number of client to MAC classA unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.22HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutUcastClassBCirFrames
OBJECT-TYPE
The number of client to MAC classB CIR unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.23HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutUcastClassBCirOctets
OBJECT-TYPE
The number of client to MAC classB CIR unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.24HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutUcastClassBEirFrames
OBJECT-TYPE
The number of client to MAC classB EIR unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.25HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutUcastClassBEirOctets
OBJECT-TYPE
The number of client to MAC classB EIR unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.26HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutUcastClassCFrames
OBJECT-TYPE
The number of client to MAC classC unicast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.27HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutUcastClassCOctets
OBJECT-TYPE
The number of client to MAC classC unicast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.28HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutMcastClassAFrames
OBJECT-TYPE
The number of client to MAC classA multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.29HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutMcastClassAOctets
OBJECT-TYPE
The number of client to MAC classA multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.30HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutMcastClassBCirFrames
OBJECT-TYPE
The number of client to MAC classB CIR multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.31HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutMcastClassBCirOctets
OBJECT-TYPE
The number of client to MAC classB CIR multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.32HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutMcastClassBEirFrames
OBJECT-TYPE
The number of client to MAC classB EIR multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.33HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutMcastClassBEirOctets
OBJECT-TYPE
The number of client to MAC classB EIR multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.34HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutMcastClassCFrames
OBJECT-TYPE
The number of client to MAC classC multicast and broadcast frames in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.35HCPerfIntervalCountread-onlycurrent
rprClientIntervalOutMcastClassCOctets
OBJECT-TYPE
The number of client to MAC classC multicast and broadcast octets in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.4.2.1.36HCPerfIntervalCountread-onlycurrent
rprClientCountersDayTable
OBJECT-TYPE
The RPR Mac Client Day Table contains the cumulative sum of the various statistics for the 24 hour period preceding the current interval. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.4.3not-accessiblecurrent
rprClientCountersDayEntry
OBJECT-TYPE
An entry in the RPR Client Day table.
1.0.8802.17.1.1.1.4.3.1not-accessiblecurrent
rprClientDayIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.4.3.1.1InterfaceIndexnot-accessiblecurrent
rprClientDayInUcastClassAFrames
OBJECT-TYPE
The number of MAC to client classA unicast frames.
1.0.8802.17.1.1.1.4.3.1.2HCPerfTotalCountread-onlycurrent
rprClientDayInUcastClassAOctets
OBJECT-TYPE
The number of MAC to client classA unicast octets.
1.0.8802.17.1.1.1.4.3.1.3HCPerfTotalCountread-onlycurrent
rprClientDayInUcastClassBCirFrames
OBJECT-TYPE
The number of MAC to client classB CIR unicast frames.
1.0.8802.17.1.1.1.4.3.1.4HCPerfTotalCountread-onlycurrent
rprClientDayInUcastClassBCirOctets
OBJECT-TYPE
The number of MAC to client classB CIR unicast octets.
1.0.8802.17.1.1.1.4.3.1.5HCPerfTotalCountread-onlycurrent
rprClientDayInUcastClassBEirFrames
OBJECT-TYPE
The number of MAC to client classB EIR unicast frames.
1.0.8802.17.1.1.1.4.3.1.6HCPerfTotalCountread-onlycurrent
rprClientDayInUcastClassBEirOctets
OBJECT-TYPE
The number of MAC to client classB EIR unicast octets.
1.0.8802.17.1.1.1.4.3.1.7HCPerfTotalCountread-onlycurrent
rprClientDayInUcastClassCFrames
OBJECT-TYPE
The number of MAC to client classC unicast frames.
1.0.8802.17.1.1.1.4.3.1.8HCPerfTotalCountread-onlycurrent
rprClientDayInUcastClassCOctets
OBJECT-TYPE
The number of MAC to client classC unicast octets.
1.0.8802.17.1.1.1.4.3.1.9HCPerfTotalCountread-onlycurrent
rprClientDayInMcastClassAFrames
OBJECT-TYPE
The number of MAC to client classA multicast and broadcast frames
1.0.8802.17.1.1.1.4.3.1.10HCPerfTotalCountread-onlycurrent
rprClientDayInMcastClassAOctets
OBJECT-TYPE
The number of MAC to client classA multicast and broadcast octets
1.0.8802.17.1.1.1.4.3.1.11HCPerfTotalCountread-onlycurrent
rprClientDayInMcastClassBCirFrames
OBJECT-TYPE
The number of MAC to client classB CIR multicast and broadcast frames
1.0.8802.17.1.1.1.4.3.1.12HCPerfTotalCountread-onlycurrent
rprClientDayInMcastClassBCirOctets
OBJECT-TYPE
The number of MAC to client classB CIR multicast and broadcast octets
1.0.8802.17.1.1.1.4.3.1.13HCPerfTotalCountread-onlycurrent
rprClientDayInMcastClassBEirFrames
OBJECT-TYPE
The number of MAC to client classB EIR multicast and broadcast frames
1.0.8802.17.1.1.1.4.3.1.14HCPerfTotalCountread-onlycurrent
rprClientDayInMcastClassBEirOctets
OBJECT-TYPE
The number of MAC to client classB EIR multicast and broadcast octets
1.0.8802.17.1.1.1.4.3.1.15HCPerfTotalCountread-onlycurrent
rprClientDayInMcastClassCFrames
OBJECT-TYPE
The number of MAC to client classC multicast and broadcast frames
1.0.8802.17.1.1.1.4.3.1.16HCPerfTotalCountread-onlycurrent
rprClientDayInMcastClassCOctets
OBJECT-TYPE
The number of MAC to client classC multicast and broadcast octets
1.0.8802.17.1.1.1.4.3.1.17HCPerfTotalCountread-onlycurrent
rprClientDayOutUcastClassAFrames
OBJECT-TYPE
The number of client to MAC classA unicast frames.
1.0.8802.17.1.1.1.4.3.1.18HCPerfTotalCountread-onlycurrent
rprClientDayOutUcastClassAOctets
OBJECT-TYPE
The number of client to MAC classA unicast octets.
1.0.8802.17.1.1.1.4.3.1.19HCPerfTotalCountread-onlycurrent
rprClientDayOutUcastClassBCirFrames
OBJECT-TYPE
The number of client to MAC classB CIR unicast frames.
1.0.8802.17.1.1.1.4.3.1.20HCPerfTotalCountread-onlycurrent
rprClientDayOutUcastClassBCirOctets
OBJECT-TYPE
The number of client to MAC classB CIR unicast octets.
1.0.8802.17.1.1.1.4.3.1.21HCPerfTotalCountread-onlycurrent
rprClientDayOutUcastClassBEirFrames
OBJECT-TYPE
The number of client to MAC classB EIR unicast frames
1.0.8802.17.1.1.1.4.3.1.22HCPerfTotalCountread-onlycurrent
rprClientDayOutUcastClassBEirOctets
OBJECT-TYPE
The number of client to MAC classB EIR unicast octets
1.0.8802.17.1.1.1.4.3.1.23HCPerfTotalCountread-onlycurrent
rprClientDayOutUcastClassCFrames
OBJECT-TYPE
The number of client to MAC classC unicast frames
1.0.8802.17.1.1.1.4.3.1.24HCPerfTotalCountread-onlycurrent
rprClientDayOutUcastClassCOctets
OBJECT-TYPE
The number of client to MAC classC unicast octets
1.0.8802.17.1.1.1.4.3.1.25HCPerfTotalCountread-onlycurrent
rprClientDayOutMcastClassAFrames
OBJECT-TYPE
The number of client to MAC classA multicast and broadcast frames.
1.0.8802.17.1.1.1.4.3.1.26HCPerfTotalCountread-onlycurrent
rprClientDayOutMcastClassAOctets
OBJECT-TYPE
The number of client to MAC classA multicast and broadcast octets.
1.0.8802.17.1.1.1.4.3.1.27HCPerfTotalCountread-onlycurrent
rprClientDayOutMcastClassBCirFrames
OBJECT-TYPE
The number of client to MAC classB CIR multicast and broadcast frames.
1.0.8802.17.1.1.1.4.3.1.28HCPerfTotalCountread-onlycurrent
rprClientDayOutMcastClassBCirOctets
OBJECT-TYPE
The number of client to MAC classB CIR multicast and broadcast octets.
1.0.8802.17.1.1.1.4.3.1.29HCPerfTotalCountread-onlycurrent
rprClientDayOutMcastClassBEirFrames
OBJECT-TYPE
The number of client to MAC classB EIR multicast and broadcast frames.
1.0.8802.17.1.1.1.4.3.1.30HCPerfTotalCountread-onlycurrent
rprClientDayOutMcastClassBEirOctets
OBJECT-TYPE
The number of client to MAC classB EIR multicast and broadcast octets.
1.0.8802.17.1.1.1.4.3.1.31HCPerfTotalCountread-onlycurrent
rprClientDayOutMcastClassCFrames
OBJECT-TYPE
The number of client to MAC classC multicast and broadcast frames.
1.0.8802.17.1.1.1.4.3.1.32HCPerfTotalCountread-onlycurrent
rprClientDayOutMcastClassCOctets
OBJECT-TYPE
The number of client to MAC classC multicast and broadcast octets.
1.0.8802.17.1.1.1.4.3.1.33HCPerfTotalCountread-onlycurrent
rprClientCountersStatsTable
OBJECT-TYPE
The local station traffic total counters table. The DiscontinuityTime for this table is indicated by ifCounterDiscontinuityTime defined in ifXTable. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.4.4not-accessiblecurrent
rprClientCountersStatsEntry
OBJECT-TYPE
An entry in the span stats table.
1.0.8802.17.1.1.1.4.4.1not-accessiblecurrent
rprClientStatsIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.4.4.1.1InterfaceIndexnot-accessiblecurrent
rprClientStatsInUcastClassAFrames
OBJECT-TYPE
The number of MAC to client classA unicast frames.
1.0.8802.17.1.1.1.4.4.1.2Counter64read-onlycurrent
rprClientStatsInUcastClassAOctets
OBJECT-TYPE
The number of MAC to client classA unicast octets.
1.0.8802.17.1.1.1.4.4.1.3Counter64read-onlycurrent
rprClientStatsInUcastClassBCirFrames
OBJECT-TYPE
The number of MAC to client classB CIR unicast frames.
1.0.8802.17.1.1.1.4.4.1.4Counter64read-onlycurrent
rprClientStatsInUcastClassBCirOctets
OBJECT-TYPE
The number of MAC to client classB CIR unicast octets.
1.0.8802.17.1.1.1.4.4.1.5Counter64read-onlycurrent
rprClientStatsInUcastClassBEirFrames
OBJECT-TYPE
The number of MAC to client classB EIR unicast frames.
1.0.8802.17.1.1.1.4.4.1.6Counter64read-onlycurrent
rprClientStatsInUcastClassBEirOctets
OBJECT-TYPE
The number of MAC to client classB EIR unicast octets.
1.0.8802.17.1.1.1.4.4.1.7Counter64read-onlycurrent
rprClientStatsInUcastClassCFrames
OBJECT-TYPE
The number of MAC to client classC unicast frames.
1.0.8802.17.1.1.1.4.4.1.8Counter64read-onlycurrent
rprClientStatsInUcastClassCOctets
OBJECT-TYPE
The number of MAC to client classC unicast octets.
1.0.8802.17.1.1.1.4.4.1.9Counter64read-onlycurrent
rprClientStatsInMcastClassAFrames
OBJECT-TYPE
The number of MAC to client classA multicast and broadcast frames
1.0.8802.17.1.1.1.4.4.1.10Counter64read-onlycurrent
rprClientStatsInMcastClassAOctets
OBJECT-TYPE
The number of MAC to client classA multicast and broadcast octets
1.0.8802.17.1.1.1.4.4.1.11Counter64read-onlycurrent
rprClientStatsInMcastClassBCirFrames
OBJECT-TYPE
The number of MAC to client classB CIR multicast and broadcast frames
1.0.8802.17.1.1.1.4.4.1.12Counter64read-onlycurrent
rprClientStatsInMcastClassBCirOctets
OBJECT-TYPE
The number of MAC to client classB CIR multicast and broadcast octets
1.0.8802.17.1.1.1.4.4.1.13Counter64read-onlycurrent
rprClientStatsInMcastClassBEirFrames
OBJECT-TYPE
The number of MAC to client classB EIR multicast and broadcast frames
1.0.8802.17.1.1.1.4.4.1.14Counter64read-onlycurrent
rprClientStatsInMcastClassBEirOctets
OBJECT-TYPE
The number of MAC to client classB EIR multicast and broadcast octets
1.0.8802.17.1.1.1.4.4.1.15Counter64read-onlycurrent
rprClientStatsInMcastClassCFrames
OBJECT-TYPE
The number of MAC to client classC multicast and broadcast frames
1.0.8802.17.1.1.1.4.4.1.16Counter64read-onlycurrent
rprClientStatsInMcastClassCOctets
OBJECT-TYPE
The number of MAC to client classC multicast and broadcast octets
1.0.8802.17.1.1.1.4.4.1.17Counter64read-onlycurrent
rprClientStatsInBcastFrames
OBJECT-TYPE
The number of MAC to client broadcast frames. This is used only when deriving the multicast and broadcast packet counters for the interface MIB.
1.0.8802.17.1.1.1.4.4.1.18Counter64read-onlycurrent
rprClientStatsOutUcastClassAFrames
OBJECT-TYPE
The number of client to MAC classA unicast frames.
1.0.8802.17.1.1.1.4.4.1.19Counter64read-onlycurrent
rprClientStatsOutUcastClassAOctets
OBJECT-TYPE
The number of client to MAC classA unicast octets.
1.0.8802.17.1.1.1.4.4.1.20Counter64read-onlycurrent
rprClientStatsOutUcastClassBCirFrames
OBJECT-TYPE
The number of client to MAC classB CIR unicast frames.
1.0.8802.17.1.1.1.4.4.1.21Counter64read-onlycurrent
rprClientStatsOutUcastClassBCirOctets
OBJECT-TYPE
The number of client to MAC classB CIR unicast octets.
1.0.8802.17.1.1.1.4.4.1.22Counter64read-onlycurrent
rprClientStatsOutUcastClassBEirFrames
OBJECT-TYPE
The number of client to MAC classB EIR unicast frames
1.0.8802.17.1.1.1.4.4.1.23Counter64read-onlycurrent
rprClientStatsOutUcastClassBEirOctets
OBJECT-TYPE
The number of client to MAC classB EIR unicast octets
1.0.8802.17.1.1.1.4.4.1.24Counter64read-onlycurrent
rprClientStatsOutUcastClassCFrames
OBJECT-TYPE
The number of client to MAC classC unicast frames
1.0.8802.17.1.1.1.4.4.1.25Counter64read-onlycurrent
rprClientStatsOutUcastClassCOctets
OBJECT-TYPE
The number of client to MAC classC unicast octets
1.0.8802.17.1.1.1.4.4.1.26Counter64read-onlycurrent
rprClientStatsOutMcastClassAFrames
OBJECT-TYPE
The number of client to MAC classA multicast and broadcast frames.
1.0.8802.17.1.1.1.4.4.1.27Counter64read-onlycurrent
rprClientStatsOutMcastClassAOctets
OBJECT-TYPE
The number of client to MAC classA multicast and broadcast octets.
1.0.8802.17.1.1.1.4.4.1.28Counter64read-onlycurrent
rprClientStatsOutMcastClassBCirFrames
OBJECT-TYPE
The number of client to MAC classB CIR multicast and broadcast frames.
1.0.8802.17.1.1.1.4.4.1.29Counter64read-onlycurrent
rprClientStatsOutMcastClassBCirOctets
OBJECT-TYPE
The number of client to MAC classB CIR multicast and broadcast octets.
1.0.8802.17.1.1.1.4.4.1.30Counter64read-onlycurrent
rprClientStatsOutMcastClassBEirFrames
OBJECT-TYPE
The number of client to MAC classB EIR multicast and broadcast frames.
1.0.8802.17.1.1.1.4.4.1.31Counter64read-onlycurrent
rprClientStatsOutMcastClassBEirOctets
OBJECT-TYPE
The number of client to MAC classB EIR multicast and broadcast octets.
1.0.8802.17.1.1.1.4.4.1.32Counter64read-onlycurrent
rprClientStatsOutMcastClassCFrames
OBJECT-TYPE
The number of client to MAC classC multicast and broadcast frames.
1.0.8802.17.1.1.1.4.4.1.33Counter64read-onlycurrent
rprClientStatsOutMcastClassCOctets
OBJECT-TYPE
The number of client to MAC classC multicast and broadcast octets.
1.0.8802.17.1.1.1.4.4.1.34Counter64read-onlycurrent
rprClientStatsOutBcastFrames
OBJECT-TYPE
The number of client to MAC broadcast frames. This is used only when deriving the multicast and broadcast packet counters for the interface MIB.
1.0.8802.17.1.1.1.4.4.1.35Counter64read-onlycurrent
rprSpanErrorCounters
OBJECT-IDENTITY
1.0.8802.17.1.1.1.5
rprSpanErrorCountersCurrentTable
OBJECT-TYPE
The RPR Errors Current counters table. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.5.1not-accessiblecurrent
rprSpanErrorCountersCurrentEntry
OBJECT-TYPE
Errors statistics for the current interval of a particular span of a particular RPR interface. The corresponding instance of rprIfTimeElapsed indicates the number of seconds which have elapsed so far in the current interval.
1.0.8802.17.1.1.1.5.1.1not-accessiblecurrent
rprSpanErrorCurrentIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.5.1.1.1InterfaceIndexnot-accessiblecurrent
rprSpanErrorCurrentSpan
OBJECT-TYPE
An indication of the span of the interface for which this row contains information.
1.0.8802.17.1.1.1.5.1.1.2RprSpannot-accessiblecurrent
rprSpanErrorCurrentTtlExpFrames
OBJECT-TYPE
The number of received (PHY to MAC) data frames that were dropped due to zero Time To Live (TTL).
1.0.8802.17.1.1.1.5.1.1.3HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentTooLongFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that exceed the maximum permitted frame size.
1.0.8802.17.1.1.1.5.1.1.4HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentTooShortFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames shortest than the minimum permitted frame size.
1.0.8802.17.1.1.1.5.1.1.5HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentBadHecFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames with HEC error.
1.0.8802.17.1.1.1.5.1.1.6HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentBadFcsFrames
OBJECT-TYPE
The number of received (PHY to MAC) data and control frames where the fcs value did not match the expected fcs value. This includes data frames passed to the client as a result of rprIfMacOperModes being not set to dropBadFcs.
1.0.8802.17.1.1.1.5.1.1.7HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentSelfSrcUcastFrames
OBJECT-TYPE
The number of received (PHY to MAC) unicast frames that were transmitted by the station itself i.e. the source MAC is equal to the interface MAC.
1.0.8802.17.1.1.1.5.1.1.8HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentPmdAbortFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were aborted by the PMD.
1.0.8802.17.1.1.1.5.1.1.9HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentBadAddrFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames with invalid SA value.
1.0.8802.17.1.1.1.5.1.1.10HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentBadParityFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames parity value not matching the expected parity value
1.0.8802.17.1.1.1.5.1.1.11HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentContainedFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were removed due to context containment
1.0.8802.17.1.1.1.5.1.1.12HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentScffErrors
OBJECT-TYPE
The number of received (PHY to MAC) errored SCFF, with bad parity, bad FCS, or both.
1.0.8802.17.1.1.1.5.1.1.13HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentErroredSeconds
OBJECT-TYPE
The number of errored seconds.
1.0.8802.17.1.1.1.5.1.1.14HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentSeverelyErroredSeconds
OBJECT-TYPE
The number of severely errored seconds.
1.0.8802.17.1.1.1.5.1.1.15HCPerfCurrentCountread-onlycurrent
rprSpanErrorCurrentUnavailableSeconds
OBJECT-TYPE
The number of unavailable seconds.
1.0.8802.17.1.1.1.5.1.1.16HCPerfCurrentCountread-onlycurrent
rprSpanErrorCountersIntervalTable
OBJECT-TYPE
The RPR Errors Interval counters table. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.5.2not-accessiblecurrent
rprSpanErrorCountersIntervalEntry
OBJECT-TYPE
Error statistics collected for a particular interval of a particular span of a particular RPR interface. The corresponding instance of rprIfValidIntervals indicates the number of intervals for which the set of statistics is available.
1.0.8802.17.1.1.1.5.2.1not-accessiblecurrent
rprSpanErrorIntervalIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.5.2.1.1InterfaceIndexnot-accessiblecurrent
rprSpanErrorIntervalSpan
OBJECT-TYPE
An indication of the span of the interface for which this row contains information.
1.0.8802.17.1.1.1.5.2.1.2RprSpannot-accessiblecurrent
rprSpanErrorIntervalNumber
OBJECT-TYPE
A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and interval identified by N is the interval immediately preceding the one identified by N-1.
1.0.8802.17.1.1.1.5.2.1.3Unsigned32 (1..96)not-accessiblecurrent
rprSpanErrorIntervalValidData
OBJECT-TYPE
This variable indicates if the data for this interval is valid. It will be valid if it contains data for 900 seconds plus or minus 10 seconds.
1.0.8802.17.1.1.1.5.2.1.4TruthValueread-onlycurrent
rprSpanErrorIntervalTimeElapsed
OBJECT-TYPE
The duration of a particular interval in seconds. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value.
1.0.8802.17.1.1.1.5.2.1.5Unsigned32 (0..899)read-onlycurrent
rprSpanErrorIntervalTtlExpFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were dropped due to zero Time To Live (TTL) in a particular interval in the past 24 hours
1.0.8802.17.1.1.1.5.2.1.6HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalTooLongFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that exceed the maximum permitted frame size in a particular interval in the past 24 hours
1.0.8802.17.1.1.1.5.2.1.7HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalTooShortFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames shortest than the minimum permitted frame size in a particular interval in the past 24 hours.
1.0.8802.17.1.1.1.5.2.1.8HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalBadHecFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames with HEC error in a particular interval in the past 24 hours
1.0.8802.17.1.1.1.5.2.1.9HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalBadFcsFrames
OBJECT-TYPE
The number of received (PHY to MAC) data and control frames where the fcs value did not match the expected fcs value. This includes data frames passed to the client as a result of rprIfMacOperModes being not set to dropBadFcs.
1.0.8802.17.1.1.1.5.2.1.10HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalSelfSrcUcastFrames
OBJECT-TYPE
The number of received (PHY to MAC) unicast frames that were transmitted by the station itself i.e. the source MAC is equal to the interface MAC, in a particular interval in the past 24 hours
1.0.8802.17.1.1.1.5.2.1.11HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalPmdAbortFrames
OBJECT-TYPE
The number of received (PHY to MAC) unicast frames that were aborted by the PMD layer, in a particular interval in the past 24 hours
1.0.8802.17.1.1.1.5.2.1.12HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalBadAddrFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames with invalid SA value.
1.0.8802.17.1.1.1.5.2.1.13HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalBadParityFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames parity value not matching the expected parity value
1.0.8802.17.1.1.1.5.2.1.14HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalContainedFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were removed due to context containment
1.0.8802.17.1.1.1.5.2.1.15HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalScffErrors
OBJECT-TYPE
The number of received (PHY to MAC) errored SCFF, with bad parity, bad FCS, or both.
1.0.8802.17.1.1.1.5.2.1.16HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalErroredSeconds
OBJECT-TYPE
The number of errored seconds.
1.0.8802.17.1.1.1.5.2.1.17HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalSeverelyErroredSeconds
OBJECT-TYPE
The number of severely errored seconds.
1.0.8802.17.1.1.1.5.2.1.18HCPerfIntervalCountread-onlycurrent
rprSpanErrorIntervalUnavailableSeconds
OBJECT-TYPE
The number of unavailable seconds.
1.0.8802.17.1.1.1.5.2.1.19HCPerfIntervalCountread-onlycurrent
rprSpanErrorCountersDayTable
OBJECT-TYPE
The RPR Mac Error Day Table contains the cumulative sum of the various statistics for the 24 hour period preceding the current interval. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.5.3not-accessiblecurrent
rprSpanErrorCountersDayEntry
OBJECT-TYPE
An entry in the RPR Error Day table.
1.0.8802.17.1.1.1.5.3.1not-accessiblecurrent
rprSpanErrorDayIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.5.3.1.1InterfaceIndexnot-accessiblecurrent
rprSpanErrorDaySpan
OBJECT-TYPE
An indication of the span of the interface for which this row contains information.
1.0.8802.17.1.1.1.5.3.1.2RprSpannot-accessiblecurrent
rprSpanErrorDayTtlExpFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were dropped due to zero Time To Live (TTL).
1.0.8802.17.1.1.1.5.3.1.3HCPerfTotalCountread-onlycurrent
rprSpanErrorDayTooLongFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that exceed the maximum permitted frame size.
1.0.8802.17.1.1.1.5.3.1.4HCPerfTotalCountread-onlycurrent
rprSpanErrorDayTooShortFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames shortest than the minimum permitted frame size.
1.0.8802.17.1.1.1.5.3.1.5HCPerfTotalCountread-onlycurrent
rprSpanErrorDayBadHecFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames with HEC error.
1.0.8802.17.1.1.1.5.3.1.6HCPerfTotalCountread-onlycurrent
rprSpanErrorDayBadFcsFrames
OBJECT-TYPE
The number of received (PHY to MAC) data and control frames where the fcs value did not match the expected fcs value. This includes data frames passed to the client as a result of rprIfMacOperModes being not set to dropBadFcs.
1.0.8802.17.1.1.1.5.3.1.7HCPerfTotalCountread-onlycurrent
rprSpanErrorDaySelfSrcUcastFrames
OBJECT-TYPE
The number of received (PHY to MAC) unicast frames that were transmitted by the station itself i.e. the source MAC is equal to the interface MAC.
1.0.8802.17.1.1.1.5.3.1.8HCPerfTotalCountread-onlycurrent
rprSpanErrorDayPmdAbortFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were aborted by the PMD
1.0.8802.17.1.1.1.5.3.1.9HCPerfTotalCountread-onlycurrent
rprSpanErrorDayBadAddrFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames with invalid SA value.
1.0.8802.17.1.1.1.5.3.1.10HCPerfTotalCountread-onlycurrent
rprSpanErrorDayBadParityFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames parity value not matching the expected parity value
1.0.8802.17.1.1.1.5.3.1.11HCPerfTotalCountread-onlycurrent
rprSpanErrorDayContainedFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were removed due to context containment
1.0.8802.17.1.1.1.5.3.1.12HCPerfTotalCountread-onlycurrent
rprSpanErrorDayScffErrors
OBJECT-TYPE
The number of received (PHY to MAC) errored SCFF, with bad parity, bad FCS, or both.
1.0.8802.17.1.1.1.5.3.1.13HCPerfTotalCountread-onlycurrent
rprSpanErrorDayErroredSeconds
OBJECT-TYPE
The number of errored seconds.
1.0.8802.17.1.1.1.5.3.1.14HCPerfTotalCountread-onlycurrent
rprSpanErrorDaySeverelyErroredSeconds
OBJECT-TYPE
The number of severely errored seconds.
1.0.8802.17.1.1.1.5.3.1.15HCPerfTotalCountread-onlycurrent
rprSpanErrorDayUnavailableSeconds
OBJECT-TYPE
The number of unavailable seconds.
1.0.8802.17.1.1.1.5.3.1.16HCPerfTotalCountread-onlycurrent
rprSpanErrorCountersStatsTable
OBJECT-TYPE
The RPR Errors total counters table. The DiscontinuityTime for this table is indicated by ifCounterDiscontinuityTime defined in ifXTable. All attributes in this table are volatile, i.e. will be cleared on system reset.
1.0.8802.17.1.1.1.5.4not-accessiblecurrent
rprSpanErrorCountersStatsEntry
OBJECT-TYPE
An entry in the span error counter table.
1.0.8802.17.1.1.1.5.4.1not-accessiblecurrent
rprSpanErrorStatsIfIndex
OBJECT-TYPE
The ifIndex of this RPR interface.
1.0.8802.17.1.1.1.5.4.1.1InterfaceIndexnot-accessiblecurrent
rprSpanErrorStatsSpan
OBJECT-TYPE
An indication of the span of the interface for which this row contains information.
1.0.8802.17.1.1.1.5.4.1.2RprSpannot-accessiblecurrent
rprSpanErrorStatsTtlExpFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were dropped due to zero Time To Live (TTL).
1.0.8802.17.1.1.1.5.4.1.3Counter64read-onlycurrent
rprSpanErrorStatsTooLongFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that exceed the maximum permitted frame size.
1.0.8802.17.1.1.1.5.4.1.4Counter64read-onlycurrent
rprSpanErrorStatsTooShortFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames shortest than the minimum permitted frame size.
1.0.8802.17.1.1.1.5.4.1.5Counter64read-onlycurrent
rprSpanErrorStatsBadHecFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames with HEC error.
1.0.8802.17.1.1.1.5.4.1.6Counter64read-onlycurrent
rprSpanErrorStatsBadFcsFrames
OBJECT-TYPE
The number of received (PHY to MAC) data and control frames where the fcs value did not match the expected fcs value. This includes data frames passed to the client as a result of rprIfMacOperModes being not set to dropBadFcs.
1.0.8802.17.1.1.1.5.4.1.7Counter64read-onlycurrent
rprSpanErrorStatsSelfSrcUcastFrames
OBJECT-TYPE
The number of received (PHY to MAC) unicast frames that were transmitted by the station itself i.e. the source MAC is equal to the interface MAC.
1.0.8802.17.1.1.1.5.4.1.8Counter64read-onlycurrent
rprSpanErrorStatsPmdAbortFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were aborted by the PMD
1.0.8802.17.1.1.1.5.4.1.9Counter64read-onlycurrent
rprSpanErrorStatsBadAddrFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames with invalid SA value.
1.0.8802.17.1.1.1.5.4.1.10Counter64read-onlycurrent
rprSpanErrorStatsBadParityFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames parity value not matching the expected parity value
1.0.8802.17.1.1.1.5.4.1.11Counter64read-onlycurrent
rprSpanErrorStatsContainedFrames
OBJECT-TYPE
The number of received (PHY to MAC) frames that were removed due to context containment
1.0.8802.17.1.1.1.5.4.1.12Counter64read-onlycurrent
rprSpanErrorStatsScffErrors
OBJECT-TYPE
The number of received (PHY to MAC) errored SCFF, with bad parity, bad FCS, or both.
1.0.8802.17.1.1.1.5.4.1.13Counter64read-onlycurrent
rprConformance
OBJECT-IDENTITY
1.0.8802.17.1.1.2
rprGroups
OBJECT-IDENTITY
1.0.8802.17.1.1.2.1
rprCompliances
OBJECT-IDENTITY
1.0.8802.17.1.1.2.2

Conformance

NameOIDStatus
rprIfGroup
OBJECT-GROUP
Collection of objects needed for RPR MAC configuration.
1.0.8802.17.1.1.2.1.1current
rprIfGroupOpt
OBJECT-GROUP
Collection of objects for RPR MAC.
1.0.8802.17.1.1.2.1.2current
rprIfStatsControlGroup
OBJECT-GROUP
Collection of objects needed for RPR MAC statistics management.
1.0.8802.17.1.1.2.1.3current
rprSpanGroup
OBJECT-GROUP
Collection of objects needed for RPR Span configuration.
1.0.8802.17.1.1.2.1.4current
rprSpanGroupOpt
OBJECT-GROUP
Collection of objects for RPR Span.
1.0.8802.17.1.1.2.1.5current
rprSpanProtectionGroup
OBJECT-GROUP
Collection of objects needed for RPR Span Protection monitoring.
1.0.8802.17.1.1.2.1.6current
rprTopoGroup
OBJECT-GROUP
Collection of objects needed for RPR Topology discovery.
1.0.8802.17.1.1.2.1.7current
rprFairnessGroup
OBJECT-GROUP
Collection of objects needed for RPR Fairness configuration.
1.0.8802.17.1.1.2.1.8current
rprFairnessGroupOpt
OBJECT-GROUP
Collection of objects for RPR Fairness.
1.0.8802.17.1.1.2.1.9current
rprOamGroup
OBJECT-GROUP
Collection of objects needed for RPR OAM configuration.
1.0.8802.17.1.1.2.1.10current
rprIfChangeSummaryGroup
OBJECT-GROUP
Collection of objects summarizes changes on the RPR interfaces.
1.0.8802.17.1.1.2.1.11current
rprSpanCurrentGroup
OBJECT-GROUP
Collection of objects counting MAC span current statistics.
1.0.8802.17.1.1.2.1.12current
rprSpanIntervalGroup
OBJECT-GROUP
Collection of objects counting MAC span intervals statistics.
1.0.8802.17.1.1.2.1.13current
rprSpanDayGroup
OBJECT-GROUP
Collection of objects counting MAC span 24 hours statistics.
1.0.8802.17.1.1.2.1.14current
rprSpanStatsGroup
OBJECT-GROUP
Collection of objects counting MAC span total statistics.
1.0.8802.17.1.1.2.1.15current
rprClientCurrentGroup
OBJECT-GROUP
Collection of objects counting MAC client interface current statistics.
1.0.8802.17.1.1.2.1.16current
rprClientIntervalGroup
OBJECT-GROUP
Collection of objects counting MAC client interface intervals statistics.
1.0.8802.17.1.1.2.1.17current
rprClientDayGroup
OBJECT-GROUP
Collection of objects counting MAC client interface 24 hours statistics.
1.0.8802.17.1.1.2.1.18current
rprClientStatsGroup
OBJECT-GROUP
Collection of objects counting MAC client interface total statistics.
1.0.8802.17.1.1.2.1.19current
rprErrorCurrentGroup
OBJECT-GROUP
Collection of objects counting MAC span error current statistics.
1.0.8802.17.1.1.2.1.20current
rprErrorIntervalGroup
OBJECT-GROUP
Collection of objects counting MAC span error intervals statistics.
1.0.8802.17.1.1.2.1.21current
rprErrorDayGroup
OBJECT-GROUP
Collection of objects counting MAC span error 24 hours statistics.
1.0.8802.17.1.1.2.1.22current
rprErrorStatsGroup
OBJECT-GROUP
Collection of objects counting MAC span error total statistics.
1.0.8802.17.1.1.2.1.23current
rprModuleTotalStatsCompliance
MODULE-COMPLIANCE
The compliance statement for agent that support RPR operation with total statistics collections.
1.0.8802.17.1.1.2.2.1current