HUAWEI-XPON-MIB

TEXTUAL-CONVENTION

Reserved parameter.

TEXTUAL-CONVENTION

The value is quering index; if no index, th value is -1. For example, if the value is XponOntPortInSpecVlan(1), the value of ifIndex, hwXponDynamicMacVlanId, hwXponDynamicMacIndex, hwXponDynamicMacQueryPara0, hwXponDynamicMacQueryPara1, hwXponDynamicMacQueryPara2 is valid, and the value of hwXponDynamicMacQueryPara3 is invalid, -1. Options: 1. xponOntPortInSpecVlan(1) - The ONT port is in the specified vlan 2. xponOntInSpecPort(2) - The specified ONT port 3. xponOntInSpecOnt(3) - The specified ONT 4. xponOntInSpecWlan(4) - The WLAN of specified ONT

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight onts, with the first octet specifying ports 0 through 7, the second octet specifying ports 8 through 15 and others. Within each octet, the most significant bit represents the lowest numbered ont, and the least significant bit represents the highest numbered ont. Thus, each ont of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that ont is included in the set of onts; the ont is not included if its bit has a value of '0'.

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16 and others. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.

TEXTUAL-CONVENTION

A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The aging time of the auto-found ONT, which can be 0s (indicating that the ONT will not aging) or a value from 100s to 300s.

OBJECT-TYPE

Indicates the SN request interval, ranging from 1(s) to 10(s).

OBJECT-TYPE

This object is used to change XPON management mode. When xpon mode is changed from profile mode to distributing mode and there are xpon data or xpon board information in system, the system will automatically save data and reboot,and will cause all configuration of XPON lost. When the mode is changed from distributing mode to profile mode, the system will automatically save data and reboot. The operation can not cause the configuration of XPON lost. Options: 1. distributingmode(1) - XPON distributing mode 2. profilemode(2) - XPON profile mode

OBJECT-TYPE

The special GEM port ID is used for the multicast service, ranging from 4000 to 4095.

OBJECT-TYPE

The base GEM port is used when the board's car-mode is port-cos, ranging from 128 to 3872.

OBJECT-TYPE

The scalar is used to configure the minimum bandwidth of the T-CONTs in the system, ranging from 384 to 1024.

OBJECT-TYPE

This object is used to open or close the switch of rogue ONT automatic detection. Options: 1.on(1) - Open the switch of rogue ONT automatic detection 2.off(2) - Close the switch of rogue ONT automatic detection The default value is off(2).

OBJECT-TYPE

This object is used to select the type of bandwidth. Options: 1.gpon(1) - Indicates that the type of bandwidth is GPON 2.ethernet(2) - Indicates that the type of bandwidth is ETH The default value is gpon(1).

OBJECT-TYPE

This object is used to select the DBA assignment mode. Options: 1.maxbandwidthusage(1) - Indicates that the usage of bandwidth is maximum 2.minloopdelay(2) - Indicates that the loop delay is minimum 3.manual(3) - Indicates that the DBA assignment mode is manual,this value can not set now

OBJECT-TYPE

This object is used to set the Organizationally Unique Identifier.

OBJECT-TYPE

The interval time of ONT's password renew, ranging from 1(s) to 254(s).

OBJECT-IDENTITY

OBJECT-TYPE

The control table of the GPON OLT. The index of this table is ifIndex.

OBJECT-TYPE

The control table of the GPON OLT. The index of this entry is ifIndex.

OBJECT-TYPE

This is the fiber distance between the OLT and the nearest ONT. For GPON, the fiber distance between the OLT and the nearest ONT is 0 km to 40 km while the maximum fiber distance between the farthest and the nearest ONTs is 20 km. For XG-PON, the fiber distance between the OLT and the nearest ONT is 0 km to 60 km while the maximum fiber distance between the farthest and the nearest ONTs is 40 km.

OBJECT-TYPE

This is the fiber distance between the OLT and the farthest ONT. For GPON, the fiber distance between the OLT and the nearest ONT is 0 km to 60 km while the maximum fiber distance between the farthest and the nearest ONTs is 20 km. For XG-PON, the fiber distance between the OLT and the nearest ONT is 0 km to 100 km while the maximum fiber distance between the farthest and the nearest ONTs is 40 km.

OBJECT-TYPE

This object indicates the downstream FEC switch. Options: 1. enable(1) - Enable the downstream FEC switch 2. disable(2) - Disable the downstream FEC switch 3. invalid(-1) - Indicates that the query fails or no information is detected For GPON, the default value is disable(2). For XG-PON, the default value is enable(1).

OBJECT-TYPE

This object indicates the ONT auto find switch. Options: 1. enable(1) - Enable the ONT auto find switch 2. disable(2) - Disable the ONT auto find switch 3. invalid(-1) - Indicates that the query fails or no information is detected The default value is disable(2).

OBJECT-TYPE

This object indicates the ONT password update period. 0 means no update, range: 0 or 5~1440 minutes.

OBJECT-TYPE

This object indicates the description of GPON port.

OBJECT-TYPE

This object indicates the untapped bandwidth of the port.

OBJECT-TYPE

This object indicates the minimum bandwidth of T-CONTs in the OLT port.

OBJECT-TYPE

This object indicates the laser switch of the GPON port. Options: 1. on(1) - Open the laser switch of the GPON port 2. off(2) - Close the laser switch of the GPON port 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the GPON port status in the OLT. Options: 1. up(1) - Indicates that the GPON port is normal 2. down(2) - Indicates that the GPON port is fault

OBJECT-TYPE

This object indicates the switch of the rogue ONT manual detection. Options: 1. startup(1) - Start up the switch of the rogue ONT manual detection 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to query whether there are Illegal incursionary rogue ONTs under port. Options: 1. inexistent(0) - Indicates that there are not Illegal incursionary rogue ONTs under port 2. existent(1) - Indicates that there are Illegal incursionary rogue ONTs under port 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the optical module status on GPON port. Options: 1. online(1) - Indicates that the optical module is online 2. offline(2) - Indicates that the optical module is offline 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the available bandwidth of the port.

OBJECT-TYPE

This object indicates the name of the optical alarm profile that is bound to the port.

OBJECT-TYPE

This object indicates the number of ONTs that are added to the port.

OBJECT-TYPE

This object indicates the time when the port last went online.

OBJECT-TYPE

This object indicates the time when the port last went offline.

OBJECT-TYPE

This object indicates the reason why the port last went offline. Options: 1. los(1) - Loss of signal 2. opticModuleAbsence(2) - The optic module is absence 3. opticModuleFault(3) - The optic module is fault 4. opticPortClosed(4) - The optic port is closed 5. otherCause(-1) - Other cause

OBJECT-TYPE

The number of the combined T-CONTs.

OBJECT-TYPE

The number of T-CONTs in the card.

OBJECT-TYPE

Energy saving state of the GPON port. Options: 1. yes (1) - The GPON port is in energy saving state 2. no (2) - The GPON port is not in energy saving state

OBJECT-TYPE

This object indicates the switch of the rogue ONT manual check. Options: 1. startup(1) - Start up the switch of the rogue ONT manual checked 2. invalid(-1) - Indicates that the query fails or no information is checked

OBJECT-TYPE

This parameter is used to reset the port. Options: 1. reset(1) - Indicates that the port resets 2. invalid(-1) - Indicates that the query fails or no information is checked

OBJECT-TYPE

This table is used to query the information about the optical transceiver. The index of this table is ifIndex.

OBJECT-TYPE

This table is used to query the information about the optical transceiver. The index of this entry is ifIndex.

OBJECT-TYPE

This object indicates the type of serial transceiver. Options: 1. unknown(1) - Unknown or unspecified 2. gbic(2) - GBIC 3. solderedToMotherboard(3) - Module soldered to motherboard 4. sfp(4) - SFP or SFP Plus 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the extended identifier of type of serial transceiver. Options: 1. notSpecifiedOrNotCompliant(1) - Not specified or not compliant with a defined MOD_DEF 2. moddef1(2) - GBIC is compliant with MOD_DEF 1 3. moddef2(3) - GBIC is compliant with MOD_DEF 2 4. moddef3(4) - GBIC is compliant with MOD_DEF 3 5. byTwowireOnly(5) - GBIC/SFP function is defined by two-wire interface ID only 6. moddef5(6) - GBIC is compliant with MOD_DEF 5 7. moddef6(7) - GBIC is compliant with MOD_DEF 6 8. moddef7(8) - GBIC is compliant with MOD_DEF 7 9. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the code for connector type. Options: 1. unknown(1) - Unknown 2. sc(2) - SC 3. copperConnector1(3) - Fibre Channel Style 1 copper connector 4. copperConnector2(4) - Fibre Channel Style 2 copper connector 5. bnctnc(5) - BNC/TNC 6. coaxialHeaders(6) - Fibre Channel coaxial headers 7. fiberJack(7) - FiberJack 8. lc(8) - LC 9. mtrj(9) - MT-RJ 10. mu(10) - MU 11. sg(11) - SG 12. opticalPigtail(12) - Optical pigtail 13. hssdcII(13) - HSSDC II 14. copperPigtail(14) - Copper Pigtail 15. mpoParallelOptic(15) - MPO Parallel Optic 16. rj45(16) - RJ45 17. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the code for serial encoding algorithm. Options: 1. unspecified(1) - Unspecified 2. encodingMethod8B10B(2) - 8B10B 3. encodingMethod4B5B(3) - 4B5B 4. nrz(4) - NRZ 5. manchester(5) - Manchester 6. sonetScrambled(6) - SONET Scrambled 7. encodingMethod64B66B(7) - 64B66B 8. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the nominal bit rate, units of 100 MBits/sec.

OBJECT-TYPE

This object indicates the link length supported for 9/125 micron fiber, units of 1000 m.

OBJECT-TYPE

This object indicates the link length supported for 9/125 micron fiber, units of 100 m.

OBJECT-TYPE

This object indicates the link length supported for 50/125 micron fiber, units of 10 m.

OBJECT-TYPE

This object indicates the link length supported for 62.5/125 micron fiber, units of 10 m.

OBJECT-TYPE

This object indicates the link length supported for copper, units of meters.

OBJECT-TYPE

This object indicates the SFP vendor name (ASCII).

OBJECT-TYPE

This object indicates the SFP vendor IEEE company ID.

OBJECT-TYPE

This object indicates the part number provided by SFP vendor (ASCII).

OBJECT-TYPE

This object indicates the revision level for part number provided by vendor (ASCII).

OBJECT-TYPE

This object indicates the laser wavelength, units of nm.

OBJECT-TYPE

This object indicates the check code for Base ID Fields.

OBJECT-TYPE

Indicates which optional transceiver signals are implemented. bit Description of option 10 Cooled laser transmitter 9 Power Level 2 requirement 8 Linear Receiver Output 7-6 Reserved 5 RATE_SELECT 4 TX_DISABLE 3 TX_FAULT 2 LOS (signal inverted from standard definition) 1 LOS (signal as defined in SFP MSA) 0 Reserved

OBJECT-TYPE

This object indicates the upper bit rate margin, units of %.

OBJECT-TYPE

This object indicates the lower bit rate margin, units of %.

OBJECT-TYPE

This object indicates the serial number provided by vendor (ASCII).

OBJECT-TYPE

This object indicates manufacturing date code of the vendor (ASCII).

OBJECT-TYPE

Indicates which type of diagnostic monitoring is implemented. bit Description of Diagnostic Monitoring Type 7 Reserved 6 Digital diagnostic monitoring 5 Internally Calibrated 4 Externally Calibrated 3 Received power measurement type:(0 = OMA, 1 = Average) 2 Address change required 1-0 Reserved

OBJECT-TYPE

Indicates which optional enhanced features are implemented. bit Description of Enhanced Options 7 Alarm/warning flags 6 TX_DISABLE control and monitoring 5 TX_FAULT monitoring 4 RX_LOS monitoring 3 RATE_SELECT control and monitoring 2 Application Select control 1 Rate Select control 0 Reserved

OBJECT-TYPE

Indicates which revision of SFF-8472 the transceiver complies Options: 1. undefined(1) - Not included or undefined 2. includesRev93SFF8472(2) - Includes functionality described in Rev 9.3 3. includesRev95SFF8472(3) - Includes functionality described in Rev 9.5 4. includesRev102SFF8472(4) - Includes functionality described in Rev 10.2 5. includesRev104SFF8472(5) - Includes functionality described in Rev 10.4 6. includesRev110SFF8472(6) - Includes functionality described in Rev 11.0 7. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the check code for the Extended ID Fields.

OBJECT-TYPE

This object indicates the vendor Specific EEPROM.

OBJECT-TYPE

This object indicates the type of the optical transceiver. Options: 1. unknown(1) - Unknown 2. gpon(2) - GPON 3. epon(3) - EPON 4. epon10g(4) - 10G EPON 5. gpon10g(5) - 10G GPON 6. wdmpon(6) - WDM PON 7. hybridpon(7) - Hybrid PON 8. gponepon(8) - GPON/EPON 9. xgspon(9) - XGS-PON 10.gponandxgpon(10) - GPON+XG-PON 11.gponandxgspon(11) - GPON+XGS-PON 12.twdmpon(15) - TWDM-PON 13.invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the sub type of the optical transceiver. Options: 1. unknown(1) - Unknown 2. classbplus(101) - CLASS B+ 3. classcplus(102) - CLASS C+ 4. classb(103) - CLASS B 5. classcplusplus(104) - CLASS C++ 6. classcd(105) - CLASS D 7. px20(201) - PX20 8. px20plus(202) - PX20+ 9. px20plusplus(203) - PX20++ 10. pr30(301) - PR30 11.pr20(302) - PR20 12.prx30(303) - PRX30 13.prx20(304) - PRX20 14.prx40(305) - PRX40 15.pr40(306) - PR40 16.prx30e(307) - PRX30-E 17.prx40e(308) - PRX40-E 18.pr30plus(309) - PR30+ 19.n2a(405) - N2a 20.n2b(406) - N2b 21.n1(407) - N1 22.e1(408) - E1 23.e2a(409) - E2a 24.e2b(410) - E2b 25.d1(411) - D1 26.d2(412) - D2 27.n2(413) - N2 28.e2(414) - E2 29.classbPlusAndPx20Plus(501) - GPON CLASS B+/EPON PX20+ 30.classbAndPx20(502) - GPON CLASS B/EPON PX20 31.invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the application scenario of the optical transceiver. Options: 1. unknown(1) - Unknown 2. olt(2) - OLT 3. ont(3) - ONT 4. onu(4) - ONU 5. catvtriplex(5) - CATV TriPlex 6. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the encapsulation information about the optical transceiver. Options: 1. unknown(1) - Unknown 2. sff2x5(2) - SFF 2x5 3. sff2x10(3) - SFF 2x10 4. sfp(4) - SFP 5. xfp(5) - XFP 6. lxfp(6) - LXFP 7. bosaonboard(7) - BOSA ON BOARD 8. sfpplus(8) - SFP+ 9. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

Indicate the part number of a optical module provided by Huawei.

OBJECT-TYPE

This table is used to query the diagnostic information about the optical transceiver of the GPON port. The index of this table is ifIndex.

OBJECT-TYPE

This table is used to query the diagnostic information about the optical transceiver of the GPON port. The index of this entry is ifIndex.

OBJECT-TYPE

This object indicates the optics temperature, units of C(centigrade).

OBJECT-TYPE

This object indicates the supply voltage, units of 0.01V.

OBJECT-TYPE

This object indicates the optics current, units of mA.

OBJECT-TYPE

This object indicates the optics send power, units of 0.01dBm.

OBJECT-TYPE

This object indicates the optics received power, units of 0.01dBm.

OBJECT-TYPE

This table is used to query the optics module informationof the 10G EPON port. The index of this table is ifIndex.

OBJECT-TYPE

This table is used to query the optics module informationof the 10G EPON port. The index of this entry is ifIndex.

OBJECT-TYPE

This object indicates the type of serial transceiver. Options: 1. unknown(0) - Unknown or unspecified 2. gbic(1) - GBIC 3. solderedToMotherboard(2) - Module soldered to motherboard 4. sfp(3) - SFP 5. pin300XBI(4) - PIN300XBI 6. xenpak(5) - XENPAK 7. xfp(6) - XFP 8. xff(7) - XFF 9. xfep(8) - XFEP 10. xpak(9) - XPAK 11. x2(10) - X2 12. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the extclei code. Options: 1. nonExtCLEICode(0) - No CLEI code present in Table 02h 2. extCLEICode(1) - CLEI code present in Table 02h 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the txref clock. Options: 1. nonExtTXRefClock(0) - TX Ref Clock Input Not Required 2. extTXRefClock(1) - TX Ref Clock Input Required 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the CDR function. Options: 1. nonExtCDRFunc(0) - Non-CDR version of XFP 2. extCDRFunc(1) - Module with CDR function 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the power level. Options: 1. extPowerLevel1(0) - Power Level 1 Module (1.5 W max. power dissipation.) 2. extPowerLevel2(1) - Power Level 2 Module (2.5W Max) 3. extPowerLevel3(2) - Power Level 3 Module (3.5W max. power dissipation.) 4. extPowerLevel4(3) - Power Level 4 Module (>3.5W max. power dissipation.) 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the code for connector type. Options: 1. unknown(1) - Unknown 2. sc(2) - SC 3. copperConnector1(3) - Fibre Channel Style 1 copper connector 4. copperConnector2(4) - Fibre Channel Style 2 copper connector 5. bnctnc(5) - BNC/TNC 6. coaxialHeaders(6) - Fibre Channel coaxial headers 7. fiberJack(7) - FiberJack 8. lc(8) - LC 9. mtrj(9) - MT-RJ 10. mu(10) - MU 11. sg(11) - SG 12. opticalPigtail(12) - Optical pigtail 13. hssdcII(13) - HSSDC II 14. copperPigtail(14) - Copper Pigtail 15. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the EncodingRZ. Options: 1. nonEncodingRZ(0) - Encoding Don't Support RZ 2. encodingRZ(1) - Encoding Support RZ 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the EncodingNRZ. Options: 1. nonEncodingNRZ(0) - Encoding Don't Support NRZ 2. encodingNRZ(1) - Encoding Support NRZ 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the Encoding8B10B. Options: 1. nonEncoding8B10B(0) - Encoding Don't Support 8B10B 2. encoding8B10B(1) - Encoding Support 8B10B 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the Encoding64B. Options: 1. nonEncoding64B(0) - Encoding Don't Support 64B/66B 2. encoding64B(1) - Encoding Support 64B/66B 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

Minimum bit rate, units of 100 MBits/s.

OBJECT-TYPE

Maximum bit rate, units of 100 MBits/s.

OBJECT-TYPE

Link length supported for SMF fiber in km.

OBJECT-TYPE

Link length supported for EBW 50/125 um fiber, units of 2 m.

OBJECT-TYPE

Link length supported for 50/125 um fiber, units of 1 m.

OBJECT-TYPE

Link length supported for 62.5/125 um fiber, units of 1 m.

OBJECT-TYPE

Link length supported for copper, units of 1m.

OBJECT-TYPE

This object indicates the transmitter support. Options: 1. nonTunable(0) - Transmitter Not Support Tunable 2. tunable(1) - Transmitter Support Tunable 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the transmitter support. Options: 1. pin(0) - PIN 2. apd(1) - APD 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the wavelength control. Options: 1. nonSupport(0) - Wavelength control NonSupport 2. support(1) - Wavelength control Support 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the cooled transmitter device. Options: 1. nonSupport(0) - Cooled transmitter device NonSupport 2. support(1) - Cooled transmitter device Support 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the transmitter technology support. Options: 1. vCSEL850(0) - vCSEL850 2. vCSEL1310(1) - vCSEL1310 3. vCSEL1550(2) - vCSEL1550 4. fP1310(3) - fP1310 5. dFB1310(4) - dFB1310 6. dFB1550(5) - dFB1550 7. eML1310(6) - eML1310 8. eML1550(7) - eML1550 9. cOPPER(8) - cOPPER 10. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XFP vendor name (ASCII).

OBJECT-TYPE

This object indicates the XFI mode. Options: 1. nonSupportXFIMode(0) - Don't Support XFI Loopback Mode 2. supportXFIMode(1) - XFI Loopback Mode Supported 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XFI mode. Options: 1. nonSupportLinesideMode(0) - Don't Support Lineside Loopback Mode 2. supportLinesideMode(1) - Lineside Loopback Mode Supported 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the max bit rate by CDR. Options: 1. cDRNosupport(0) - CDR not support 2. maxBitRateSupportedByCDR11p1(1) - CDR support for 11.1 Gb/s 3. maxBitRateSupportedByCDR10p7(3) - CDR support for 10.7 Gb/s 4. maxBitRateSupportedByCDR10p5(7) - CDR support for 10.5 Gb/s 5. maxBitRateSupportedByCDR10p3(15) - CDR support for 10.3 Gb/s 6. maxBitRateSupportedByCDR9p95(31) - CDR support for 9.95 Gb/s 7. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the Vendor OUI.

OBJECT-TYPE

This object indicates the Vendor PN.

OBJECT-TYPE

This object indicates the Vendor rev.

OBJECT-TYPE

This object indicates the Wavelength.

OBJECT-TYPE

This object indicates the WaveTolerance.

OBJECT-TYPE

This object indicates the Maximum Case Temperature in Degrees C.

OBJECT-TYPE

This object indicates the Cc_base.

OBJECT-TYPE

This object indicates the Maximum Power Dissipation.

OBJECT-TYPE

This object indicates the Maximum Total Power Dissipation in Power Down Mode.

OBJECT-TYPE

This object indicates the Maximum current required by +5V Supply.

OBJECT-TYPE

This object indicates the Maximum current required by +3.3V Supply.

OBJECT-TYPE

This object indicates the Maximum current required by +1.8V Supply.

OBJECT-TYPE

This object indicates the Maximum current required by -5.2V Supply.

OBJECT-TYPE

This object indicates the Vendor SN.

OBJECT-TYPE

This object indicates the Date code.

OBJECT-TYPE

This object indicates the Received power measurement type. Options: 1. supportOMA(0) - OMA 2. supportAveragePower(1) - Average Power 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the Module Respond to FEC BER. Options: 1. nonSupportBER(0) - No BER Support 2. supportBER(1) - BER Support 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

Indicates which optional enhanced features are implemented. bit Description of Enhanced Options 7 Module Supports Optional VPS 6 Optional Soft TX_DISABLE implemented 5 Optional Soft P_down implemented 4 Supports VPS LV regulator mode 3 Supports VPS bypassed regulator Mode 2 Active FEC control functions implemented 1 Wavelength tunability implemented 0 Optional CMU Support Mode invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the optics Aux Input One. Options: 1. auxInputType1(0) - Auxiliary monitoring not implemented 2. auxInputType2(1) - APD Bias Voltage 3. auxInputType3(2) - 1G Tx Bias Current 4. auxInputType4(3) - TEC Current (mA) 5. auxInputType5(4) - Laser Temperature 6. auxInputType6(5) - Laser Wavelength 7. auxInputType7(6) - +5V Supply Voltage 8. auxInputType8(7) - 1G Tx Power 9. auxInputType9(8) - +1.8V Supply Voltage 10. auxInputType10(9) - -5.2V Supply Voltage 11. auxInputType11(10) - +5V Supply Current 12. auxInputType14(13) - +3.3V Supply Current 13. auxInputType15(14) - +1.8V Supply Current 14. auxInputType16(15) - -5.2V Supply Current 15. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the optics Aux Input two. Options: 1. auxInputType1(0) - Auxiliary monitoring not implemented 2. auxInputType2(1) - APD Bias Voltage 3. auxInputType3(2) - 1G Tx Bias Current 4. auxInputType4(3) - TEC Current (mA) 5. auxInputType5(4) - Laser Temperature 6. auxInputType6(5) - Laser Wavelength 7. auxInputType7(6) - +5V Supply Voltage 8. auxInputType8(7) - 1G Tx Power 9. auxInputType9(8) - +1.8V Supply Voltage 10. auxInputType10(9) - -5.2V Supply Voltage 11. auxInputType11(10) - +5V Supply Current 12. auxInputType14(13) - +3.3V Supply Current 13. auxInputType15(14) - +1.8V Supply Current 14. auxInputType16(15) - -5.2V Supply Current 15. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the CC_EXT .

OBJECT-TYPE

This object indicates the Wavelength for 2.5G.

OBJECT-TYPE

This object indicates the Wavelength for 1.25G.

OBJECT-TYPE

This object indicates the Vendor specific.

OBJECT-TYPE

This object indicates the module type. Options: 1. unknown(1) - Unknown 2. gpon(2) - GPON 3. epon(3) - EPON 4. epon10g(4) - 10G EPON 5. gpon10g(5) - 10G GPON 6. wdmpon(6) - WDM PON 7. hybridpon(7) - Hybrid PON 8. gponepon(8) - GPON/EPON 9. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the sub module type. Options: 1. unknown(1) - Unknown 2. classbplus(101) - CLASS B+ 3. classcplus(102) - CLASS C+ 4. classb(103) - CLASS B 5. classcplusplus(104) - CLASS C++ 6. px20(201) - PX20 7. px20plus(202) - PX20+ 8. px20plusplus(203) - PX20++ 9. pr30(301) - PR30 10.pr20(302) - PR20 11.prx30(303) - PRX30 12.prx20(304) - PRX20 13.prx40(305) - PRX40 14.pr40(306) - PR40 15.prx30e(307) - PRX30E 16.prx40e(308) - PRX40E 17.pr30plus(309) - PR3PLUS 18.n2a(405) - N2a 19.n2b(406) - N2b 20.n1(407) - N1 21.e1(408) - E1 22.e2a(409) - E2a 23.e2b(410) - E2b 24.invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the application scenario of the optical transceiver. Options: 1. unknown(1) - Unknown 2. olt(2) - OLT 3. ont(3) - ONT 4. onu(4) - ONU 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the encapsulation information about the optical transceiver. Options: 1. unknown(1) - Unknown 2. sff2x5(2) - SFF 2x5 3. sff2x10(3) - SFF 2x10 4. sfp(4) - SFP 5. xfp(5) - XFP 6. lxfp(6) - LXFP 7. bosaonboard(7) - BOSA ON BOARD 8. sfpplus(8) - SFP+ 9. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the application scenario of the optical transceiver. Options: 1. unknown(1) - Unknown 2. commercial(2) - commercial 3. industry(3) - industry 4. expandtemperature(4) - expand temperature 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the OPM precision. Options: 1. unknown(1) - Unknown 2. db3(2) - 3db 3. db1(3) - 1db 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This table implements the control of the EPON port. The index of this table is ifIndex.

OBJECT-TYPE

This table implements the control of the EPON port. The index of this entry is ifIndex.

OBJECT-TYPE

This object indicates the fiber distance between the OLT and the farthest ONT EPON: 0-40 km 10 Gb/s EPON: 0-60 km

OBJECT-TYPE

This object indicates the ONT auto find switch. Options: 1. enable(1) - Enable the ONT auto find switch 2. disable(2) - Disable the ONT auto find switch 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the description of the EPON port.

OBJECT-TYPE

This object indicates the laser switch of the EPON port. Options: 1. on(1) - Open the laser switch of the EPON port 2. off(2) - Close the laser switch of the EPON port 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the EPON port status in the OLT: Options: 1. up(1) - Indicates that the EPON port is normal 2. down(2) - Indicates that the EPON port is fault

OBJECT-TYPE

This object indicates the up-stream bandwidth of EPON port.

OBJECT-TYPE

This object indicates the down-stream bandwidth of EPON port.

OBJECT-TYPE

This object indicates the short delay switch status that is saved in the database of the OLT.

OBJECT-TYPE

This object is used to query the short delay switch status that is saved in the database of the OLT.

OBJECT-TYPE

This object is the flag indicating whether the buffer function takes effect immediately.

OBJECT-TYPE

This object indicates the status of the EPON low time switch.

OBJECT-TYPE

This object indictates the number of ONTs that are added to the port.

OBJECT-TYPE

This object indicates the configuration function of the VLAN tag mode of the PON port. Options: 1. tagbasedont(1) - Tag-based-ont 2. tagbasedvlan(2) - Tag-based-vlan 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the time when the port last goes online.

OBJECT-TYPE

This object indicates the time when the port last goes offline.

OBJECT-TYPE

This object indicates the reason why the port last goes offline. Options: 1. los(1) - Loss of signal 2. opticModuleAbsence(2) - The optic module is absence 3. opticModuleFault(3) - The optic module is fault 4. opticPortClosed(4) - The optic port is closed 5. otherCause(-1) - Other cause

OBJECT-TYPE

This object indicates the untapped bandwidth of 1G upstream ONT's port, unit Kbps.

OBJECT-TYPE

This object indicates the available bandwidth of 1G upstream ONT's port, unit Kbps.

OBJECT-TYPE

This object indicates the switch of the rogue ONT manual detection. Options: 1. startup(1) - Starts up the switch of the rogue ONT manual detection 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to query whether there are Illegal incursionary rogue ONTs under port. Options: 1. inexistent(0) - Indicates that there are not Illegal incursionary rogue ONTs under port 2. existent(1) - Indicates that there are Illegal incursionary rogue ONTs under port

OBJECT-TYPE

This object indicates the untapped bandwidth of 10G upstream ONT's port, unit Kbps.

OBJECT-TYPE

This object indicates the available bandwidth of 10G upstream ONT's port, unit Kbps.

OBJECT-TYPE

This object indicates the name of the alarm profile that is bound to the EPON port.

OBJECT-TYPE

This object indicates the name of the warning profile that is bound to the EPON port.

OBJECT-TYPE

Energy saving state of the EPON port. Options: 1. yes (1) - The EPON port is in energy saving state 2. no (2) - The EPON port is not in energy saving state

OBJECT-TYPE

This object indicates the switch of the rogue ONT manual check. Options: 1. startup(1) - Start up the switch of the rogue ONT manual checked 2. invalid(-1) - Indicates that the query fails or no information is checked

OBJECT-TYPE

This parameter is used to reset the port. Options: 1. reset(1) - Indicates that the port resets 2. invalid(-1) - Indicates that the query fails or no information is checked

OBJECT-TYPE

Show the optics module information. The index of this table is ifIndex.

OBJECT-TYPE

Show the optics module information. The index of this entry is ifIndex.

OBJECT-TYPE

This object indicates the type of serial transceiver. Options: 1. unknown(1) - Unknown or unspecified 2. gbic(2) - GBIC 3. solderedToMotherboard(3) - Module soldered to motherboard 4. sfp(4) - SFP or SFP Plus 5. invalid (-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the extended identifier of type of serial transceiver. Options: 1. notSpecifiedOrNotCompliant(1) - Not specified or not compliant with a defined MOD_DEF 2. moddef1(2) - GBIC is compliant with MOD_DEF 1 3. moddef2(3) - GBIC is compliant with MOD_DEF 2 4. moddef3(4) - GBIC is compliant with MOD_DEF 3 5. byTwowireOnly(5) - GBIC/SFP function is defined by two-wire interface ID only 6. moddef5(6) - GBIC is compliant with MOD_DEF 5 7. moddef6(7) - GBIC is compliant with MOD_DEF 6 8. moddef7(8) - GBIC is compliant with MOD_DEF 7 9. invalid (-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the code for connector type. Options: 1. unknown(1) - Unknown 2. sc(2) - SC 3. copperConnector1(3) - Fibre Channel Style 1 copper connector 4. copperConnector2(4) - Fibre Channel Style 2 copper connector 5. bnctnc(5) - BNC/TNC 6. coaxialHeaders(6) - Fibre Channel coaxial headers 7. fiberJack(7) - FiberJack 8. lc(8) - LC 9. mtrj(9) - MT-RJ 10. mu(10) - MU 11. sg(11) - SG 12. opticalPigtail(12) - Optical pigtail 13. hssdcII(13) - HSSDC II 14. copperPigtail(14) - Copper Pigtail 15. mpoParallelOptic(15) - MPO Parallel Optic 16. rj45(16) - RJ45 17. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the code for serial encoding algorithm. Options: 1. unspecified(1) - Unspecified 2. encodingMethod8B10B(2) - 8B10B 3. encodingMethod4B5B(3) - 4B5B 4. nrz(4) - NRZ 5. manchester(5) - Manchester 6. sonetScrambled(6) - SONET Scrambled 7. encodingMethod64B66B(7) - 64B66B 8. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the nominal bit rate, units of 100 MBits/sec.

OBJECT-TYPE

This object indicates the link length supported for 9/125 micron fiber, units of 1000 m.

OBJECT-TYPE

This object indicates the link length supported for 9/125 micron fiber, units of 100 m.

OBJECT-TYPE

This object indicates the link length supported for 50/125 micron fiber, units of 10 m.

OBJECT-TYPE

This object indicates the link length supported for 62.5/125 micron fiber, units of 10 m.

OBJECT-TYPE

This object indicates the link length supported for copper, units of meters.

OBJECT-TYPE

This object indicates the SFP vendor name (ASCII).

OBJECT-TYPE

This object indicates the SFP vendor IEEE company ID.

OBJECT-TYPE

This object indicates the part number provided by SFP vendor (ASCII).

OBJECT-TYPE

This object indicates the revision level for part number provided by vendor (ASCII).

OBJECT-TYPE

This object indicates the laser wavelength, units of nm.

OBJECT-TYPE

This object indicates the check code for Base ID Fields.

OBJECT-TYPE

Indicates which optional transceiver signals are implemented. bit Description of option 10 Cooled laser transmitter 9 Power Level 2 requirement 8 Linear Receiver Output 7-6 Reserved 5 RATE_SELECT 4 TX_DISABLE 3 TX_FAULT 2 LOS (signal inverted from standard definition) 1 LOS (signal as defined in SFP MSA) 0 Reserved

OBJECT-TYPE

This object indicates the upper bit rate margin, units of %.

OBJECT-TYPE

This object indicates the lower bit rate margin, units of %.

OBJECT-TYPE

This object indicates the serial number provided by vendor (ASCII).

OBJECT-TYPE

This object indicates manufacturing date code of the vendor (ASCII).

OBJECT-TYPE

Indicates which type of diagnostic monitoring is implemented. bit Description of Diagnostic Monitoring Type 7 Reserved 6 Digital diagnostic monitoring 5 Internally Calibrated 4 Externally Calibrated 3 Received power measurement type:(0 = OMA, 1 = Average) 2 Address change required 1-0 Reserved

OBJECT-TYPE

Indicates which optional enhanced features are implemented. bit Description of Enhanced Options 7 Alarm/warning flags 6 TX_DISABLE control and monitoring 5 TX_FAULT monitoring 4 RX_LOS monitoring 3 RATE_SELECT control and monitoring 2 Application Select control 1 Rate Select control 0 Reserved

OBJECT-TYPE

Indicates which revision of SFF-8472 the transceiver complies Options: 1. undefined(1) - Not included or undefined 2. includesRev93SFF8472(2) - Includes functionality described in Rev 9.3 3. includesRev95SFF8472(3) - Includes functionality described in Rev 9.5 4. includesRev102SFF8472(4) - Includes functionality described in Rev 10.2 5. includesRev104SFF8472(5) - Includes functionality described in Rev 10.4 6. includesRev110SFF8472(6) - Includes functionality described in Rev 11.0 7. invalid (-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the check code for the Extended ID Fields.

OBJECT-TYPE

This object indicates the vendor Specific EEPROM.

OBJECT-TYPE

This object indicates the type of the optical transceiver. Options: 1. unknown(1) - Unknown 2. gpon(2) - GPON 3. epon(3) - EPON 4. epon10g(4) - 10G EPON 5. gpon10g(5) - 10G GPON 6. wdmpon(6) - WDM PON 7. hybridpon(7) - Hybrid PON 8. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the sub type of the optical transceiver. Options: 1. unknown(1) - Unknown 2. classbplus(101) - CLASS B+ 3. classcplus(102) - CLASS C+ 4. classb(103) - CLASS B 5. classcplusplus(104) - CLASS C++ 6. px20(201) - PX20 7. px20plus(202) - PX20+ 8. px20plusplus(203) - PX20++ 9. pr30(301) - PR30 10.pr20(302) - PR20 11.prx30(303) - PRX30 12.prx20(304) - PRX20 13.prx40(305) - PRX40 14.pr40(306) - PR40 15.prx30e(307) - PRX30-E 16.prx40e(308) - PRX40-E 17.pr30plus(309) - PR30+ 18.n2a(405) - N2a 19.n2b(406) - N2b 20.n1(407) - N1 21.e1(408) - E1 22.e2a(409) - E2a 23.e2b(410) - E2b 24.invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the application scenario of the optical transceiver. Options: 1. unknown(1) - Unknown 2. olt(2) - OLT 3. ont(3) - ONT 4. onu(4) - ONU 5.invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the encapsulation information about the optical transceiver. Options: 1. unknown(1) - Unknown 2. sff2x5(2) - SFF 2x5 3. sff2x10(3) - SFF 2x10 4. sfp(4) - SFP 5. xfp(5) - XFP 6. lxfp(6) - LXFP 7. bosaonboard(7) - BOSA ON BOARD 8.invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This table is used to query the diagnostic information about the optical transceiver of the EPON port. The index of this table is ifIndex.

OBJECT-TYPE

This table is used to query the diagnostic information about the optical transceiver of the EPON port. The index of this entry is ifIndex.

OBJECT-TYPE

This object indicates the optics temperature, units of C(centigrade).

OBJECT-TYPE

This object indicates the supply voltage, units of 0.01V.

OBJECT-TYPE

This object indicates the optics current, units of mA.

OBJECT-TYPE

This object indicates the optics send power, units of 0.01dBm.

OBJECT-TYPE

This object indicates the optics receive power, units of 0.01dBm.

OBJECT-TYPE

It is used to add ont to loading list and query the loading state for ONT. The index of this table is a combination of ifIndex and hwXponDeviceOntIndex.

OBJECT-TYPE

It is used to add ont to loading list and query the loading state for ONT. The index of this entry is a combination of ifIndex and hwXponDeviceOntIndex.

OBJECT-TYPE

This object indicates the ONT ID, range: 0~255. The value of 255 indicates that ONT ID is invalid or ignored in process of ont loading.

OBJECT-TYPE

This object indicates the loading state of the ONT. Options: 1. ready(1) - Indicates that the loading state of the ONT is ready 2. loading(2) - Indicates that the loading state of the ONT is loading 3. success(3) - Indicates that the loading state of the ONT is success 4. fail(4) - Indicates that the loading state of the ONT is fail 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the loading progress of the ONT

OBJECT-TYPE

This object is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object is used to set the priority of an ONT loading task. A smaller value represents a higher priority.

OBJECT-TYPE

This object is used to configure the effect mode of an loaded ONT. Options: 1. nextstartup(1) - Indicates that the ONT takes effect after next startup 2. immediate(2) - Indicates that the ONT takes effect immediately 3. graceful(3) - Indicates that the ONT takes effect gracefully 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates the ONT file type. Options: 1. app(1) - Application load 2. cfg(2) - Configuration load 3. inValidFileType(255) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the server IP address.

OBJECT-TYPE

This object indicates the transfer protocol. Options: 1. tftp(1) - TFTP 2. ftp(2) - FTP 3. sftp(3) - SFTP 4. inValidProtocol(255) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the file name.

OBJECT-TYPE

This object indicates the user name.

OBJECT-TYPE

This object indicates the password.

OBJECT-TYPE

This object indicates the ONT loading flag. Options: 1. start(1) - Indicates that the loading of ONT is started 2. stop(2) - Indicates that the loading of ONT is stopped 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

F/S/P of ONT loading xml file. If the value of the ACCESS clause is 'write-only', then the value of the MAX-ACCESS clause MUST be 'read-write', and the DESCRIPTION clause SHALL note that reading this object will result in implementation-specific results.

OBJECT-TYPE

ONT ID of loading xml file. If the value of the ACCESS clause is 'write-only', then the value of the MAX-ACCESS clause MUST be 'read-write', and the DESCRIPTION clause SHALL note that reading this object will result in implementation-specific results.

OBJECT-TYPE

Active mode of ont loading. Options: 1. nextstartup(1) - Indicates that the ONT takes effect after next startup 2. immediate(2) - Indicates that the ONT takes effect immediately 3. graceful(3) - Indicates that the ONT takes effect gracefully 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the AES-128 cryptographic key for the ont xml file. This AES-128 key is 128bits(16 Bytes).

OBJECT-TYPE

This object indicates the port of server for ont loading. The TFTP port default value is 69. The FTP port default value is 21. The SFTP port default value is 22.

OBJECT-TYPE

This table is used to create, modify, delete or query an ONT. The index of this table is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

This table is used to create, modify, delete or query an ONT. The index of this entry is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

This object indicates the ONT ID, range: 0-127.

OBJECT-TYPE

This object indicates the authentication mode for the ONT. Options: 1. sn(1) - Serial Number 2. snpassword(2) - SN and password 3. alwayson(3) - Password + always-on 4. onceon(4) - Password + once-on 5. loidalwayson (5) - LOID + always-on 6. loidonceon (6) - LOID + once-on 7. loidcheckcodealwayson (7) - LOID + CHECKCODE + always-on 8. loidcheckcodeonceon (8) - LOID + CHECKCODE + once-on 9. snorpassword(9) - SN or password 10.invalid(-1) - Indicates that the query fails or no information is detected If the hwGponDeviceOntAuthMethod leaf is not specified for creation of a table instance, the default authentication mode sn(1) is used.

OBJECT-TYPE

This object indicates the configured ONT serial number.

OBJECT-TYPE

This object indicates the ONT password. GPON password size (0..10) XG-PON password size (0..36)

OBJECT-TYPE

This object indicates the registered working period of the ONT, ranging from 1 to 168 hours. The value (-1) indicates that there is no-aging time.

OBJECT-TYPE

This object indicates the ONT management mode, including OMCI and SNMP. Options: 1. omci(1) - OMCI 2. snmp(2) - SNMP 3. extendFrame(3) - extendFrame 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the name of the profile that is bound to the ONT.

OBJECT-TYPE

This object indicates the name of the service profile that is bound to the ONT.

OBJECT-TYPE

This object indicates the description of the ONT.

OBJECT-TYPE

This object is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row 3. active(1) -when this leaf is queried, the value is fixed to active(1)

OBJECT-TYPE

This object indicates whether the ONT is the ONT on the protection side. Options: 1. protectside(1) - Indicates that the ONT is the ONT on the protection side 2. work(2) - Indicates that the ONT is the ONT on the work side

OBJECT-TYPE

This object indicates the role of the ont in the protect group. Options: 1. work(1) - Indicates that the role of the ONT is work 2. protect(2) - Indicates that the role of the ONT is protection 3. unjoined(-1) - Indicates that the ONT is not added to the protect group

OBJECT-TYPE

The object indicates the LOID of the ONT.

OBJECT-TYPE

The object indicates the checkcode of the ONT.

OBJECT-TYPE

Indicate the type of the ont re-register type for once-on authentication mode, if the ont authentication mode is not once-on, the value is invalid. if the ont authentication mode is once-on, the default is snPassword. Options: 1. sn(1) -Indicate the re-register type of the ont is sn authentication type 2. snPassword(2) -Indicate the re-register type of the ont is snPassword authentication type 3. invalid(-1) -Indicate the re-register type of the ont is invalid

OBJECT-TYPE

Indicates the effect taking mode after the ONT authentication mode is changed. The default effect taking mode is immediate. Options: 1. immediate (1) -Indicates that the change will take effect immediately. 2. nextstartup (2) -Indicates that the change will take effect when the ONT goes online next time. 3. invalid (-1) -Indicates that the effect taking mode is invalid.

OBJECT-TYPE

This object indicates the NNI type of the ONT. Options: 1. rate2dot5G1dot25G (1) -Downstream rate 2.5Gbps, upstream rate 1.25Gbps. 2. rate10G2dot5G (2) -Downstream rate 10Gbps, upstream rate 2.5Gbps. 3. rate10G10G (3) -Downstream rate 10Gbps, upstream rate 10Gbps. 4. auto(4) -Indicates the actual ont nni type is automatically selected. 5. invalid (-1) -Indicates the invalid value.

OBJECT-TYPE

Indicates the destination channel's ifindex that the ont switch to. Only the ont under a dynamic channel group support to switch channel.

OBJECT-TYPE

This is the ONT extend function configuration table. The index of this table is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

This is the ONT extend function configuration table. The index of this entry is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

The name of the ONT alarm profile.

OBJECT-TYPE

The name of the ONT SNMP profile.

OBJECT-TYPE

This object indicates the name of the optical alarm profile that is bound to the ONT.

OBJECT-TYPE

This is the ONT version information table. The index of this table is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

This is the ONT version information table. The index of this entry is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

The ONT version number.

OBJECT-TYPE

This object indicates the ONT VendorID.

OBJECT-TYPE

This object indicates the ONT productID.

OBJECT-TYPE

This object indicates the ONT equipmentID.

OBJECT-TYPE

The active softerware version of the ONT.

OBJECT-TYPE

The standby software version of the ONT.

OBJECT-TYPE

The object indicates the software working mode of the GPON ONT. Options: 1. normal(1) - Normal 2. survivalmode(2) - Survival mode

OBJECT-TYPE

This object indicates the ONT customize information.

OBJECT-TYPE

This object indicates the ONT Equipment Sn.

OBJECT-TYPE

This object indicates the ONT MAC address.

OBJECT-TYPE

This is the control table of the ONT. The index of this table is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

This is the control table of the ONT. The index of this entry is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

This object is used to activate or deactivate an ONT. Options: 1. activate(1) - Activates an ONT 2. deactivate(2) - Deactivate an ONT 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to reset an ONT. Options: 1. reset(1) - Reset an ONT 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to re-register an ONT. Options: 1. reRegister(1) - Re-register an ONT 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to reset the discovery status of an ONT. If the authentication mode is once-on(4), after performing the rediscovery operation, the registered working period is re-timed. Options: 1. rediscovery(1) - Reset the discovery status of an ONT 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT running status. Options: 1. up(1) - Normal 2. down(2) - Fault 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This is the ONT configuration resume status. If it is failed(3), the ONT is down and the service is interrupted. If the config status is noresume (4), set the resume policy as resume for the system and re-register the ONT. Options: 1. initialization(1) - Indicates that the ONT configuration resume status is initialization 2. normal(2) - Indicates that the ONT configuration resume status is normal 3. failed(3) - Indicates that the ONT configuration resume status is failed 4. noresume(4) - Indicates that the ONT configuration resume status is not resumed 5. config(5) - Indicates that the ONT configuration resume status is configuration 6. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT discovery state. Options: 1. on(1) - Indicates that the ONT discovery state is on 2. off(2) - Indicates that the ONT discovery state is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT match status. Options: 1. initialization(1) - Indicates that the ONT is initialization 2. match(2) - Indicates that the ONT is matched 3. mismatch(3) - Indicates that the ONT is mismatched 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the DBA report status. Options: 1. nsr(1) - NSR 2. sr(2) - SR 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the result of the ONT ranging. Unit: m Options: 1. invalid (-1) - Indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the number of MAC addresses that are learned by the ONT.

OBJECT-TYPE

This object indicates the time when the ONT last went online.

OBJECT-TYPE

This object indicates the time when the ONT last went offline.

OBJECT-TYPE

This object indicates the reason why the ONT last went offline. The value (1) indicates that the reason is LOS(Loss of signal), The value (2) indicates that the reason is LOSi(Loss of signal for ONUi) or LOBi (Loss of burst for ONUi), The value (3) indicates that the reason is LOFI(Loss of frame of ONUi), The value (4) indicates that the reason is SFI(Signal fail of ONUi), The value (5) indicates that the reason is LOAI(Loss of acknowledge with ONUi), The value (6) indicates that the reason is LOAMI(Loss of PLOAM for ONUi), The value (7) indicates that the reason is deactive ONT fails, The value (8) indicates that the reason is deactive ONT success, The value (9) indicates that the reason is reset ONT, The value (10) indicates that the reason is re-register ONT, The value (11) indicates that the reason is pop up fail, The value (13) indicates that the reason is dying-gasp, The value (15) indicates that the reason is LOKI(Loss of key synch with ONUi), The value (18) indicates that the reason is deactived ONT due to the ring, The value (30) indicates that the reason is shut down ONT optical module, The value (31) indicates that the reason is reset ONT by ONT command, The value (32) indicates that the reason is reset ONT by ONT reset button, The value (33) indicates that the reason is reset ONT by ONT software, The value (34) indicates that the reason is deactived ONT due to broadcast attack, The value (35) indicates that the reason is operator check fail, The value (37) indicates that the reason is a rogue ONT detected by itself, The value (-1) indicates that the query fails.

OBJECT-TYPE

This object indicates the time when the ONT last went down due to Dying Gasp.

OBJECT-TYPE

This object indicates the ONT isolation status. Options: 1. normal(0) - Indicates that the ONT is normal 2. isolated(1) - Indicates that the ONT is isolated

OBJECT-TYPE

This object indicates the ONT battery status. Options: 1. notSupport(0) - Not support 2. charge(1) - Charge state 3. discharge(2) - Discharge state 4. holding(3) - Holding state 5. supportButInvalid(4) - Provisioned and present but cannot recharge 6. unknownStatus(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The number of the combined T-CONTs.

OBJECT-TYPE

This object indicates the result of the ONT last ranging. Unit: m Options: 1. invalid (-1) - Indicates that the query fails or no information is detected.

OBJECT-TYPE

The ONT's actual serial number.

OBJECT-TYPE

The ONT configuration capability table. The index of this table is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

The ONT configuration capability table. The index of this entry is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

This object indicates the ONT's management mode, including omci and snmp. Options: 1. omci(1) - OMCI 2. snmp(2) - SNMP 3. extendFrame(3) - Extend Frame 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the number of ethernet ports. A special value of 0xFE (254) indicates the number of port is adaptive. The value is -1 when the query fails or no information is detected.

OBJECT-TYPE

This object indicates the number of POTS ports. A special value of 0xFE (254) indicates the number of port is adaptive The value is -1 when the query fails or no information is detected.

OBJECT-TYPE

This object indicates the IP address configuration mode. Options: 1. dhcp(1) - DHCP 2. static(2) - Indicates that the IP address configuration mode is static 3. unconfiguration(3) - Indicates that the IP address is not configuration 4. pppoe(4) - Indicates that the IP address configuration mode is pppoe 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the TDM port type. Options: 1. t1(13) - T1 2. e1(14) - E1 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the TDM service type. Options: 1. tdmovergem(1) - Tdm over gem 2. cesop(2) - Cesop 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the number of TDM ports. The value is -1 when the query fails or no information is detected.

OBJECT-TYPE

This object indicates the number of MOCA ports. The value is -1 when the query fails or no information is detected.

OBJECT-TYPE

This object indicates the number of CATV UNI ports. A special value of 0xFE (254) indicates the number of port is adaptive The value is -1 when the query fails or no information is detected.

OBJECT-TYPE

This object indicates the number of GEM ports. The value is -1 when the query fails or no information is detected.

OBJECT-TYPE

This object indicates the mapping mode. Options: 1. vlan(1) - The mapping mode is vlan 2. pri8021p(2) - The mapping mode is 802.1p 3. vlanpri(3) - The mapping mode is vlan and 802.1p 4. port(4) - The mapping mode is port 5. vlanport(5) - The mapping mode is vlan and port 6. portpri(6) - The mapping mode is port and 802.1p 7. vlanpriport(7) - The mapping mode is vlan, port and 802.1p 8. e1t1port(8) - The mapping mode is the port of e1 and t1 9. iptos(9) - The mapping mode is iptos 10. vlaniptos(10) - The mapping mode is vlan and iptos 11. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the number of T-CONTs. The value is -1 when the query fails or no information is detected.

OBJECT-TYPE

This object indicates the type of flow control. Options: 1. pq(1) - The type of flow control is PQ 2. gemportcar(2) - The type of flow control is the gemportcar 3. flowcar(3) - The type of flow control is the flowcar 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the number of VDSL ports. A special value of 0xFE (254) indicates the number of port is adaptive. The value is -1 when the query fails or no information is detected.

OBJECT-TYPE

This table is used to query the information about the auto-found ONTs in the system. The index of this table is a combination of ifIndex and hwGponDeviceAutoFindOntInfoOntIndex.

OBJECT-TYPE

This table is used to query the information about the auto-found ONTs in the system. The index of this entry is a combination of ifIndex and hwGponDeviceAutoFindOntInfoOntIndex.

OBJECT-TYPE

The index of the auto-found ONT.

OBJECT-TYPE

This object indicates the ONT serial number.

OBJECT-TYPE

This object indicates the ONT password. GPON password size (0..10) XG-PON password size (0..36)

OBJECT-TYPE

This object indicates the ONT vendorid.

OBJECT-TYPE

This object indicates the ONT Version.

OBJECT-TYPE

This object indicates the ONT MainSoftVer.

OBJECT-TYPE

This object indicates the ONT EquipmentId.

OBJECT-TYPE

This object indicates the time for ONT's auto find.

OBJECT-TYPE

This object indicates the ONT LOID.

OBJECT-TYPE

This object indicates the ONT CHECKCODE

OBJECT-TYPE

This object indicates the ONT customize information.

OBJECT-TYPE

This object indicates the ONT actual rate type. Options: 1. rate2dot5G1dot25G(1) - Downstream rate 2.5Gbps, upstream rate 1.25Gbps 2. rate10G2dot5G(2) - Downstream rate 10Gbps, upstream rate 2.5Gbps 3. rate10G10G(3) - Downstream rate 10Gbps, upstream rate 10Gbps 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT Equipment Sn.

OBJECT-TYPE

This object indicates the ONT MAC address.

OBJECT-TYPE

This is the ONT IP configuration table. This table is used to configure and query the IP configuration mode and IP address of an ONT. The index of this table is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntIpIndex.

OBJECT-TYPE

This is the ONT IP configuration table. This table is used to configure and query the IP configuration mode and IP address of an ONT. The index of this entry is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntIpIndex.

OBJECT-TYPE

This object indicates the IP configuration mode. Options: 1. dhcp(1) - DHCP 2. static(2) - Indicates that the IP configuration mode is static 3. unconfiguration(3) - Indicates that the IP is not configuration 4. configurationFile(4) - Indicates that the IP is configuration file 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the IP address.

OBJECT-TYPE

This object indicates the Subnet mask.

OBJECT-TYPE

This object indicates the ONT MAC address.

OBJECT-TYPE

This object indicates the default network gateway.

OBJECT-TYPE

This object indicates the active DNS address.

OBJECT-TYPE

This object indicates the slave DNS address.

OBJECT-TYPE

This object indicates the management VLAN of ONT. range: 0-4095

OBJECT-TYPE

The management priority of ONT. range: 0-7, 0xfe: dscpMapping, -1: invalid value.

OBJECT-TYPE

This object indicates the IP index of the ont IP host

OBJECT-TYPE

This object indicates the default priority for dscpMapping policy. range: 0-7

OBJECT-TYPE

This object indicates the dscp profile index of the ONT ip host.

OBJECT-TYPE

This object is used for resetting the ip host in the DHCP mode. Options: 1. reset(1) - DHCP reset in the DHCP mode 2. invalid(-1) - invalid

OBJECT-TYPE

The table is used to query the state of the ONT alarms. The index of this table is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

The table is used to query the state of the ONT alarms. The index of this entry is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

This object indicates the signal degrade (SDi) alarm. 1: no alarm is generated; 2: alarm is generated.

OBJECT-TYPE

This object indicates the signal fail (SFi) alarm. 1: no alarm is generated; 2: alarm is generated.

OBJECT-TYPE

This object indicates the the ONU DOWi alarm. 1: no alarm is generated; 2: alarm is generated.

OBJECT-TYPE

This object indicates the loss of frame (LOSi) alarm. 1: no alarm is generated; 2: alarm is generated.

OBJECT-TYPE

This object indicates the remote defect indication (RDIi) alarm 1: no alarm is generated; 2: alarm is generated.

OBJECT-TYPE

The table is used to query the information of the ONT Optical module. The index of this table is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

The table is used to query the information of the ONT Optical module. The index of this entry is a combination of ifIndex and hwGponDeviceOntIndex.

OBJECT-TYPE

The temperature of the optical module, unit C(centigrade).

OBJECT-TYPE

The Bias Current of the optical module, unit mA.

OBJECT-TYPE

The transmitting power of the optical module, unit 0.01dBm.

OBJECT-TYPE

The receiving power of the optical module, unit 0.01dBm.

OBJECT-TYPE

The power feed voltage of the optical module, unit mV.

OBJECT-TYPE

The ONT optical power received on the OLT, unit dBm. The relationship between the actual value and the value get from this leaf node is as follows, Actual value = ((Node value - 10000) / 100)

OBJECT-TYPE

Indicates the CATV receiving optical power of the optical module, unit 0.01dBm.

OBJECT-TYPE

This table is used to query the register information about the ONT, including the ONT SN, register time and register result. The index of this table is a combination of ifIndex and hwGponDeviceOntRegisterSerialNum.

OBJECT-TYPE

This table is used to query the register information about the ONT, including the ONT SN, register time and register result. The index of this entry is a combination of ifIndex and hwGponDeviceOntRegisterSerialNum.

OBJECT-TYPE

This object indicates the register number.

OBJECT-TYPE

This object indicates the ONT serial number.

OBJECT-TYPE

This object indicates the register result. Options: 1. success(1) - Indicates that the register result is success 2. fail(2) - Indicates that the register result is fail 3. snConflict(3) - Indicates that the SN conflict 4. passwordConflict(4) - Indicates that the password conflict 5. loidConflict(5) - Indicates that the LOID conflict 6. passwordError(6) - Indicates that the password conflict 7. ccError(7) - Indicates that the CC error 8. rangingOnuFail(8) - Indicates that the ranging ONU fail 9. unconfirmed(9) - Indicates that the ONU is unconfirmed 10. misMatch(10) - Indicates that the ONU is mismatch 11. loidError(11) - Indicates that the LOID error 12. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the register time. -1 is the invalid value.

OBJECT-TYPE

This object indicates the ifIndex of the conflicted ONT. -1 is the invalid value.

OBJECT-TYPE

This object indicates the index of the conflicted ONT. -1 is the invalid value.

OBJECT-TYPE

This object indicates the ONT password GPON password size (0..10) XG-PON password size (0..36)

OBJECT-TYPE

This object indicates the ONT vendor ID.

OBJECT-TYPE

This object indicates the ONT version.

OBJECT-TYPE

This object indicates the ONT mainsoft version.

OBJECT-TYPE

This object indicates the ONT equipment ID.

OBJECT-TYPE

This object indicates the ONT LOID.

OBJECT-TYPE

This object indicates the ONT CHECKCODE

OBJECT-TYPE

This object indicates the ONT actual rate type. Options: 1. rate2dot5G1dot25G(1) - Downstream rate 2.5Gbps, upstream rate 1.25Gbps 2. rate10G2dot5G(2) - Downstream rate 10Gbps, upstream rate 2.5Gbps 3. rate10G10G(3) - Downstream rate 10Gbps, upstream rate 10Gbps 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This table is used to create, modify, delete or query an ONT. The index of this table is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This table is used to create, modify, delete or query an ONT. The index of this entry is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This object indicates the ONT ID, range: 0~254.

OBJECT-TYPE

This object indicates the authentication mode for the ONT. Options: 1. onceon(1) - The authentication mode is once on 2. alwayson(2) - The authentication mode is always on 3. mac(3) - The authentication mode is MAC 4. lOIDonceon(5) - The authentication mode is LOID and once on 5. lOIDalwayson(6) - The authentication mode is LOID and always on 6. lOIDCheckCodeOnceon(7) - The authentication mode is LOID, checkcode and once on 7. lOIDCheckCodeAlwayson(8) - The authentication mode is LOID, checkcode and once always on 8. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT MAC.

OBJECT-TYPE

This object indicates the ONT password.

OBJECT-TYPE

This object indicates the registered working period of the ONT, ranging from 1 to 168 hours. The value (-1) indicates that there is no-aging time.

OBJECT-TYPE

This object indicates the ONT management mode, including OAM and SNMP. Options: 1. oam(1) - OAM 2. snmp(2) - SNMP 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the name of the line profile that is bound to the ONT.

OBJECT-TYPE

This object indicates the name of the service profile that is bound to the ONT.

OBJECT-TYPE

This object indicates the description of the ONT.

OBJECT-TYPE

This object is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates whether the ONT is the ONT on the protection side. Options: 1. protectside(1) - Indicates that the ONT is the ONT on the protection side 2. work(2) - Indicates that the ONT is the ONT on the work side

OBJECT-TYPE

This object indicates the ONT LOID.

OBJECT-TYPE

This object indicates the ONT CHECKCODE.

OBJECT-TYPE

This object indicates the index of SLA profile

OBJECT-TYPE

Indicate the role of the ont in the protect group, Options: 1. work(1) - Indicates that the role of the ONT is work 2. protect(2) - Indicates that the role of the ONT is protection 3. unjoined(-1) - Indicates that the ONT is not added to the protect group

OBJECT-TYPE

Indicates the effect taking mode after the ONT authentication mode is changed. The default effect taking mode is immediate. Options: 1. immediate (1) -Indicates that the change will take effect immediately. 2. nextstartup (2) -Indicates that the change will take effect when the ONT goes online next time. 3. invalid (-1) -Indicates that the effect taking mode is invalid.

OBJECT-TYPE

This object indicates the ONT rate type. Options: 1. rate1G1G(1) - Downstream rate 1Gbps, upstream rate 1Gbps 2. rate10G1G(2) - Downstream rate 10Gbps, upstream rate 1Gbps 3. rate10G10G(3) - Downstream rate 10Gbps, upstream rate 10Gbps 4. auto(4) - Indicates that the ONT NNI type is automatically selected 5. rate10G2G(5) - Downstream rate 10Gbps, upstream rate 2Gbps 6. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This is the ONT extend function configuration table. The index of this table is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This is the ONT extend function configuration table. The index of this entry is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This object indicates the name of the ONT SNMP profile.

OBJECT-TYPE

This object indicates the XPON service profile multicast mode. Options: 1. ctc(1) - Indicates that the XPON service profile multicast mode is CTC 2. igmpsnooping(2) - Indicates that the XPON service profile multicast mode is igmp snooping 3. transparent(3) - Indicates that the XPON service profile multicast mode is transparent 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the name of the optical alarm profile that is bound to the ONT.

OBJECT-TYPE

This object indicates the name of the alarm profile that is bound to the ONT PON port.

OBJECT-TYPE

This object indicates the name of the warning profile that is bound to the ONT PON port.

OBJECT-TYPE

This is the ONT version information table. The index of this table is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This is the ONT version information table. The index of this entry is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This object indicates the ONT VendorID.

OBJECT-TYPE

This object indicates the ONT model.

OBJECT-TYPE

This object indicates the ONT identifier.

OBJECT-TYPE

This object indicates the hardware version of the ONT.

OBJECT-TYPE

This object indicates the software version of the ONT.

OBJECT-TYPE

This object indicates the verder ID of the ONT's chip.

OBJECT-TYPE

This object indicates the model of the ONT's chip.

OBJECT-TYPE

This object indicates the verion of the ONT's chip.

OBJECT-TYPE

This object indicates the design data of the ONT's chip.

OBJECT-TYPE

This object indicates the firmware version of the ONT's chip.

OBJECT-TYPE

This object indicates the firmware reversion of the ONT's chip.

OBJECT-TYPE

The object indicates the software working mode of the EPON ONT. Options: 1. normal(1) - Normal 2. survivalmode(2) - Survival mode

OBJECT-TYPE

This object indicates the ONT extended model.

OBJECT-TYPE

This object indicates the highest version of ONT OUI.

OBJECT-TYPE

This object indicates the extended firmware version of the ONT's chip.

OBJECT-TYPE

This object indicates the ONT customize information.

OBJECT-TYPE

The EPON ONT configuration capability table. The index of this table is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

The EPON ONT configuration capability table. The index of this entry is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This object indicates the ONT's management mode, including oam and snmp. Options: 1. oam(1) - OAM 2. snmp(2) - SNMP 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the number of POTS ports. A special value of 0xFE (254) indicates the number of port is adaptive.

OBJECT-TYPE

This object indicates the IP config mode. Options: 1. dhcp(1) - DHCP 2. static(2) - Indicates that the IP config mode is static 3. unconfiguration(3) - Indicates that the IP is not configuration 4. pppoe(4) - Indicates that the IP config mode is PPPoE 5. invalid (-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the TDM port type. Options: 1. t1(13) - T1 2. e1(14) - E1 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the number of TDM ports.

OBJECT-TYPE

This object indicates the number ethernet ports. A special value of 0xFE (254) indicates the number of port is adaptive.

OBJECT-TYPE

This is the control table of the ONT. The index of this table is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This is the control table of the ONT. The index of this entry is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This object is used to activate or deactivate an ONT. Options: 1. activate(1) - Activates an ONT 2. deactivate(2) - Deactivates an ONT 3. invalid (-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to reset an ONT. Options: 1. reset(1) - Reset an ONT 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to re-register an ONT. Options: 1. reRegister(1) - Re-register an ONT 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to reset the discovery status of an ONT. If the authentication mode is once-on(4), after performing the rediscovery operation, the registered working period is re-timed. Options: 1. rediscovery(1) - Reset the discovery status of an ONT 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT ping.

OBJECT-TYPE

This object indicates the ONT running status. Options: 1. up(1) - Normal 2. down(2) - Fault 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This is the ONT configuration resume status. If it is failed(3), the ONT is down and the service is interrupted. If the config status is noresume (4), set the resume policy as resume for the system and re-register the ONT. Options: 1. initialization(1) - Indicates that the ONT configuration resume status is initialization 2. normal(2) - Indicates that the ONT configuration resume status is normal 3. failed(3) - Indicates that the ONT configuration resume status is failed 4. noresume(4) - Indicates that the ONT configuration resume status is not resumed 5. config(5) - Indicates that the ONT configuration resume status is configuration 6. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT discovery state. Options: 1. on(1) - Indicates that the ONT discovery state is on 2. off(2) - Indicates that the ONT discovery state is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT match status. Options: 1. initialization(1) - Indicates that the ONT is initialization 2. match(2) - Indicates that the ONT is matched 3. mismatch(3) - Indicates that the ONT is mismatched 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the result of the ONT ranging.

OBJECT-TYPE

This object indicates the result of the ONT ranging(RTT).

OBJECT-TYPE

This object indicates the upstream bandwidth of the ONT.

OBJECT-TYPE

This object indicates the downstream bandwidth of the ONT.

OBJECT-TYPE

This object indicates the time when the ONT last goes online.

OBJECT-TYPE

This object indicates the time when the ONT last goes offline.

OBJECT-TYPE

This object indicates the reason why the ONT last went offline. The value (1) indicates that the reason is LOS(Loss of signal), The value (2) indicates that the reason is LOSI(Loss of signal for ONUi), The value (3) indicates that the reason is LOFI(Loss of frame of ONUi), The value (4) indicates that the reason is SFI(Signal fail of ONUi), The value (5) indicates that the reason is LOAI(Loss of acknowledge with ONUi), The value (6) indicates that the reason is LOAMI(Loss of PLOAM for ONUi), The value (7) indicates that the reason is deactive ONT fails, The value (8) indicates that the reason is deactive ONT success, The value (9) indicates that the reason is reset ONT, The value (10) indicates that the reason is re-register ONT, The value (11) indicates that the reason is pop up fail, The value (12) indicates that the reason is authentication fail, The value (13) indicates that the reason is dying-gasp, The value (14) reserved, The value (15) indicates that the reason is LOKI(Loss of key synch with ONUi), The value (18) indicates that the reason is deactived ONT due to the ring, The value (30) indicates that the reason is shut down ONT optical module, The value (31) indicates that the reason is reset ONT by ONT command, The value (32) indicates that the reason is reset ONT by ONT reset button, The value (33) indicates that the reason is reset ONT by ONT software, The value (34) indicates that the reason is deactived ONT due to broadcast attack, The value (37) indicates that the reason is a rogue ONT detected by itself, The value (-1) indicates that the query fails.

OBJECT-TYPE

This object indicates the time when the ONT last goes down due to Dying Gasp.

OBJECT-TYPE

This object indicates the ONT isolation status. Options: 1. normal(0) - Indicates that the ONT is normal 2. isolated(1) - Indicates that the ONT is isolated

OBJECT-TYPE

This object indicates the ONT actual rate type. Options: 1. rate1G1G(1) - Downstream rate 1Gbps, upstream rate 1Gbps 2. rate10G1G(2) - Downstream rate 10Gbps, upstream rate 1Gbps 3. rate10G10G(3) - Downstream rate 10Gbps, upstream rate 10Gbps 4. rate10G2G(5) - Downstream rate 10Gbps, upstream rate 2Gbps 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT last actual rate type. Options: 1. rate1G1G(1) - Downstream rate 1Gbps, upstream rate 1Gbps 2. rate10G1G(2) - Downstream rate 10Gbps, upstream rate 1Gbps 3. rate10G10G(3) - Downstream rate 10Gbps, upstream rate 10Gbps 4. rate10G2G(5) - Downstream rate 10Gbps, upstream rate 2Gbps 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the result of the ONT last ranging.

OBJECT-TYPE

The table is used to query ONT(s) that are found automatically. The index of this table is a combination of ifIndex and hwEponDeviceAutoFindOntInfoOntIndex.

OBJECT-TYPE

The table is used to query ONT(s) that are found automatically. The index of this entry is a combination of ifIndex and hwEponDeviceAutoFindOntInfoOntIndex.

OBJECT-TYPE

This object indicates the auto find ONT index, range: 0~254.

OBJECT-TYPE

This object indicates the MAC address of ONT.

OBJECT-TYPE

This object indicates the password of ONT.

OBJECT-TYPE

This object indicates the Vendor identifier of ONT.

OBJECT-TYPE

This object indicates the Software version of ONT.

OBJECT-TYPE

This object indicates the hardware version of ONT.

OBJECT-TYPE

This object indicates the time for ONT's auto find.

OBJECT-TYPE

This object indicates the Mode of ONT.

OBJECT-TYPE

This object indicates the ONT LOID.

OBJECT-TYPE

This object indicates the ONT CHECKCODE.

OBJECT-TYPE

This object indicates the ONT actual rate type. Options: 1. rate1G1G(1) - Downstream rate 1Gbps, upstream rate 1Gbps 2. rate10G1G(2) - Downstream rate 10Gbps, upstream rate 1Gbps 3. rate10G10G(3) - Downstream rate 10Gbps, upstream rate 10Gbps 4. rate10G2G(5) - Downstream rate 10Gbps, upstream rate 2Gbps 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT extended model.

OBJECT-TYPE

This object indicates the highest ONT OUI version

OBJECT-TYPE

This object indicates the ONT customize information.

OBJECT-TYPE

This table is used to query the ONT capability set. The index of this table is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This table is used to query the ONT capability set. The index of this entry is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This object indicates the number of POTS ports.

OBJECT-TYPE

This object indicates the number of FE ports.

OBJECT-TYPE

This object indicates the number of GE ports.

OBJECT-TYPE

This object indicates the number of TDM ports.

OBJECT-TYPE

This object indicates whether the ONT supports the FEC. The value (1) indicates that the ONT supports the FEC. The value (2) indicates that the ONT not supports the FEC. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates whether the ONT supports the standby battery.

OBJECT-TYPE

This object indicates the increment of the allocated bandwidth of the upstream queue.

OBJECT-TYPE

This object indicates the number of upstream queues.

OBJECT-TYPE

This object indicates the maximum number of queues of the upsstream port.

OBJECT-TYPE

This object indicates the number of downstream queues.

OBJECT-TYPE

This object indicates the maximum number of queues of the downstream port.

OBJECT-TYPE

This object indicates the bitmap of the FE port.

OBJECT-TYPE

This object indicates the bitmap of the GE port.

OBJECT-TYPE

This object indicates the multicast quick leave capability.

OBJECT-TYPE

This object indicates the ONT device type. Options: 1. sfu(0) - SFU 2. hgu(1) - HGU 3. sbu(2) - SBU 4. boxShapedMDU(3) - Box shaped MDU 5. smallCapacityCardTypeMDU(4) - Small capacity card type MDU 6. boxShapedCardTypeMDU(5) - Box shaped card type MDU 7. rackCardTypeMDU(6) - Rack card type MDU 8. cardTypeMDU(7) - Card type MDU 9. mtu(8) - MTU 10. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT device multiLLID. -1 indicates an invalid value. A value from 1 to 255 indicates the number of supported LLIDs. In CTC Technical Specification for EPON Equipment V2.1_200904, 0 indicates that multiple LLIDs are supported. In CTC Technical Specification for EPON Equipment V2.1_200912, 0 indicates an invalid value.

OBJECT-TYPE

This object indicates the ONT protection type. Options: 1. unsupport(0) - Do not support the ONT protection 2. typecProtection(1) - Type C protection 3. typedProtection(2) - Type D protection 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT device ponIF number.

OBJECT-TYPE

This object indicates the ONT device slot number.

OBJECT-TYPE

This object indicates the ONT device ADSL2 + port number

OBJECT-TYPE

This object indicates the ONT device VDSL2 port number.

OBJECT-TYPE

This object indicates the ONT device WLAN port number.

OBJECT-TYPE

This object indicates the ONT device USB port number.

OBJECT-TYPE

This object indicates the ONT device CATV port number.

OBJECT-TYPE

This object indicates whether the ONT supports IPv6 aware. Options: 1.unsupport(1) - Indicates that the ONT does not support IPv6 aware. 2.support(2) - Indicates that the ONT supports IPv6 aware. 3.invalid(-1) - Indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates whether the ONT supports power supply control. Options: 1. unsupport(1) - Indicates that the ONT does not support power supply control. 2. supportTx(2) - Indicates that the ONT only supports Tx power supply control. 3. supportTxAndRx(3) - Indicates that the ONT supports both Tx power and Rx power supply control. 4. invalid(-1) - Indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates whether the ONT supports service SLA. The value (1) indicates that the ONT does not support service SLA. The value (2-8) indicates the number of the ONT supports service SLA. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the number of 10GE ports.

OBJECT-TYPE

This is the ONT IP configuration table. This table is used to configure and query the IP configuration mode and IP address of an ONT. The index of this table is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This is the ONT IP configuration table. This table is used to configure and query the IP configuration mode and IP address of an ONT. The index of this entry is a combination of ifIndex and hwEponDeviceOntIndex.

OBJECT-TYPE

This object indicates the management VLAN.

OBJECT-TYPE

This object indicates the IP address.

OBJECT-TYPE

This object indicates the subnet mask of the IP address.

OBJECT-TYPE

This object indicates the default network gateway.

OBJECT-TYPE

The hwEponDeviceOntIpConfigRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates the management priority of MDU.

OBJECT-TYPE

This table is used to query the register information about the ONT, including the ONT MAC, register time and register result. The index of this table is a combination of ifIndex and hwEponDeviceSerialNum.

OBJECT-TYPE

This table is used to query the register information about the ONT, including the ONT MAC, register time and register result. The index of this entry is a combination of ifIndex and hwEponDeviceSerialNum.

OBJECT-TYPE

This object indicates the register number.

OBJECT-TYPE

This object indicates the ONT MAC.

OBJECT-TYPE

This object indicates the register result. Options: 1. success(1) - Indicates that the register result is success 2. fail(2) - Indicates that the register result is fail 3. macConflict(3) - Indicates that the MAC conflict 4. passwordConflict(4) - Indicates that the password conflict 5. loidConflict(5) - Indicates that the LOID conflict 6. passwordError(6) - Indicates that the password conflict 7. ccError(7) - Indicates that the CC error 8. rangingOnuFail(8) - Indicates that the ranging ONU fail 9. unconfirmed(9) - Indicates that the ONU is unconfirmed 10. misMatch(10) - Indicates that the ONU is mismatch 11. loidError(11) - Indicates that the LOID error 12. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the register time. -1 is the invalid value.

OBJECT-TYPE

This object indicates the ifIndex of the conflicted ONT. -1 is the invalid value.

OBJECT-TYPE

This object indicates the index of the conflicted ONT. -1 is the invalid value.

OBJECT-TYPE

This object indicates the ONT password. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed. A null is reported in other scenarios.

OBJECT-TYPE

This object indicates the ONT vendor ID. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed.

OBJECT-TYPE

This object indicates the Software version of ONT. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed. A null is reported in other scenarios.

OBJECT-TYPE

This object indicates the hardware version of ONT. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed. A null is reported in other scenarios.

OBJECT-TYPE

This object indicates the Mode of ONT. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed.

OBJECT-TYPE

This object indicates the ONT LOID. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed. A null is reported in other scenarios.

OBJECT-TYPE

This object indicates the ONT CHECKCODE. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed. A null is reported in other scenarios.

OBJECT-TYPE

This object indicates the ONT actual rate type. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed. Options: 1. rate1G1G(1) - Downstream rate 1Gbps, upstream rate 1Gbps 2. rate10G1G(2) - Downstream rate 10Gbps, upstream rate 1Gbps 3. rate10G10G(3) - Downstream rate 10Gbps, upstream rate 10Gbps 4. rate10G2G(5) - Downstream rate 10Gbps, upstream rate 2Gbps 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT extended model. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed. A null is reported in other scenarios.

OBJECT-TYPE

This object indicates the highest ONT OUI version. A valid value is reported only when hwEponDeviceRegOntResult is unconfirmed. A null is reported in other scenarios.

OBJECT-TYPE

This is the ONT ETH port table, This table is used to set or query the attribute of the ONT ETH port, including duplex, transmission rate and native VLAN and others. The index of this table is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntEthernetPortId. When the attribute of an ONT ETH port is queried on the NMS, if the port is bound with hwGponDeviceOntEthernetOnlineState, the running states of the port is queried. If the port is not bound with hwGponDeviceOntEthernetOnlineState, the configuration of the port is queried.

OBJECT-TYPE

This is the ONT ETH port table, This table is used to set or query the attribute of the ONT ETH port, including duplex, transmission rate and native VLAN and others. The index of this entry is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntEthernetPortId. When the attribute of an ONT ETH port is queried on the NMS, if the port is bound with hwGponDeviceOntEthernetOnlineState, the running states of the port is queried. If the port is not bound with hwGponDeviceOntEthernetOnlineState, the configuration of the port is queried.

OBJECT-TYPE

This object indicates the ONT ETH port ID.

OBJECT-TYPE

This object indicates the negotiation switch. The value (1) indicates that the negotiation switch is on. The value (2) indicates that the negotiation switch is off. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the duplex type of the port. Options: 1. half(1) - Forced half duplex 2. full(2) - Forced full duplex 3. autoneg(3) - Auto negotiation 4. autohalf(4) - Auto half duplex 5. autofull(5) - Auto full duplex 6. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the transmission rate of the port. Options: 1. speed10M(1) - The forced transmission rate of the port is 10M 2. speed100M(2) - The forced transmission rate of the port is 100M 3. speed1000M(3) - The forced transmission rate of the port is 1000M 4. autoneg(4) - The transmission rate of the port is auto negotiation 5. autospeed10M(5) - The auto transmission rate of the port is 10M 6. autospeed100M(6) - The auto transmission rate of the port is 100M 7. autospeed1000M(7) - The auto transmission rate of the port is 1000M 8. speed10G(8) - The forced transmission rate of the port is 10G 9. autospeed10G(9) - The auto transmission rate of the port is 10G 10. speed2500M(10) - The forced transmission rate of the port is 2500M 11. autospeed2500M(11) - The auto transmission rate of the port is 2500M 12. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the switch of the port. Options: 1. on(1) - Indicates that the switch of the port is on 2. off(2) - Indicates that the switch of the port is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to set the flow control switch of ONT port. Options: 1. on(1) - Indicates that the flow control switch of ONT port is on 2. off(2) - Indicates that the flow control switch of ONT port is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the native VLAN of the port.

OBJECT-TYPE

This object indicates the native VLAN priority of the port.

OBJECT-TYPE

This object indicates the actual ETH port type of the ONT. The value (13) indicates that the port type is t1, The value (14) indicates that the port type is e1, The value (24) indicates that the port type is fe, The value (34) indicates that the port type is ge, The value (46) indicates that the port type is moca, The value (47) indicates that the port type is eth, The value (50) indicates that the port type is iphost, The value (-1) indicates that the query fails.

OBJECT-TYPE

This object indicates the status of ONT ETH port. Options: 1. linkup(1) - Indicates that the status of ONT ETH port is link up 2. linkdown(2) - Indicates that the status of ONT ETH port is link down 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT ethernet port upstream car profile id (1~1024, 0xfffe-unconcern).

OBJECT-TYPE

This object indicates the ONT ethernet port downstream car profile id (1~1024, 0xfffe-unconcern).

OBJECT-TYPE

The object is used to enable or disable the switch of ONT port IGMP forward mode. Options: 1. disable(1) - Disable the switch of ONT port IGMP forward mode 2. enable(2) - Enable the switch of ONT port IGMP forward mode 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The object is used to enable or disable the switch of ONT port IGMP forward mode. Options: 1. loop(1) - Indicates that the ring status of ONT ETH port is loop 2. noloop(2) - Indicates that the ring status of ONT ETH port is no loop 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT ethernet port upstream car profile name.

OBJECT-TYPE

This object indicates the ONT ethernet port downstream car profile name.

OBJECT-TYPE

This object indicates the actual route switch status of ONT ETH port. Options: 1. enable(1) - Indicates that the route switch status of ONT ETH port is enable 2. disable(2) - Indicates that the route switch status of ONT ETH port is disable 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

Indicates the optical module status of the ONT ethernet port. Options: 1. electric(1) - Indicates that the mode status of ONT ETH port is electric 2. optic(2) - Indicates that the mode status of ONT ETH port is optic 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The status of the ONT ethernet port. Options: 1. normal(1) - Indicates that the optical module status of ONT ETH port is normal 2. absence(2) - Indicates that the optical module status of ONT ETH port is absence 3. mismatch(3) - Indicates that the optical module status of ONT ETH port is mismatch 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

Indicates the online duration of the ONT ethernet port. Unit: second

OBJECT-TYPE

This is the ONT CATV port table. The index of this table is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntCatvPortId.

OBJECT-TYPE

This is the ONT CATV port table. The index of this entry is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntCatvPortId.

OBJECT-TYPE

This object indicates the ONT CATV port ID.

OBJECT-TYPE

This object indicates the laser switch of ONT CATV port. Options: 1. on(1) - Indicates that the laser switch of ONT CATV port is on 2. off(2) - Indicates that the laser switch of ONT CATV port is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the link status of ONT CATV port. The value (1) indicates that the CATV port is online. The value (2) indicates that the CATV port is offline. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the frequency of ONT CATV port. Options: 1. allPass(1) - Indicates that the frequency of ONT CATV port is all-pass 2. highPass(2) - Indicates that the frequency of ONT CATV port is high-pass 3. lowPass(3) - Indicates that the frequency of ONT CATV port is low-pass 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the Tx power of ONT CATV port. Unit: 0.001dBmV Options: 1. invalid(0x7FFFFFFF) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This is the ONT MOCA port config table. The index of this table is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntMocaPortId.

OBJECT-TYPE

This is the ONT MOCA port config table. The index of this entry is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntMocaPortId.

OBJECT-TYPE

This object indicates the ONT MOCA port ID.

OBJECT-TYPE

This object indicates the native VLAN of the Moca port.

OBJECT-TYPE

This object indicates the native VLAN priority of the MOCA port. The range is from 0 to 7, and the value (-1) is invalid.

OBJECT-TYPE

This is the ONT IPHOST port config table. The index of this table is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntIpHostPortId.

OBJECT-TYPE

This is the ONT IPHOST port config table. The index of this entry is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntIpHostPortId.

OBJECT-TYPE

This object indicates the ONT IPHOST port ID.

OBJECT-TYPE

This object indicates the native VLAN of the IPHOST port.

OBJECT-TYPE

This object indicates the native VLAN priority of the IPHOST port. The range is from 0 to 7, and the value (-1) is invalid.

OBJECT-TYPE

This is the ONT ETH port config table. The index of this table is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntEthernetPortId.

OBJECT-TYPE

This is the ONT ETH port config table. The index of this entry is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntEthernetPortId.

OBJECT-TYPE

This object indicates the ONT ETH port ID.

OBJECT-TYPE

This object indicates the negotiation switch. Options: 1. auto(1) - Indicates that the negotiation switch is auto negotiation 2. neg(2) - Indicates that the negotiation switch is negotiation 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the duplex type of the port. Options: 1. half(1) - Forced half duplex 2. full(2) - Forced full duplex 3. autoneg(3) - Auto negotiation 4. autohalf(4) - Auto half duplex 5. autofull(5) - Auto full duplex 6. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the transmission rate of the port. Options: 1. speed10M(10) - The forced transmission rate of the port is 10M 2. speed100M(100) - The forced transmission rate of the port is 100M 3. speed1000M(1000) - The forced transmission rate of the port is 1000M 4. autoneg(4) - The transmission rate of the port is auto negotiation 5. autospeed10M(5) - The auto transmission rate of the port is 10M 6. autospeed100M(6) - The auto transmission rate of the port is 100M 7. autospeed1000M(7) - The auto transmission rate of the port is 1000M 8. speed10G(8) - The forced transmission rate of the port is 10G 9. autospeed10G(9) - The auto transmission rate of the port is 10G 10. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the native VLAN of the port.

OBJECT-TYPE

This object indicates the switch of the port. Options: 1. on(1) - Indicates that the switch of the port is on 2. off(2) - Indicates that the switch of the port is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to set ONT port flow control switch. Options: 1. on(1) - Indicates that the switch of ONT port flow control is on 2. off(2) - Indicates that the switch of ONT port flow control is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ring status of ONT ETH port. Options: 1. forward(1) - Indicates that the ring status of ONT ETH port is forward 2. block(2) - Indicates that the ring status of ONT ETH port is block 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the status of ONT ETH port. Options: 1. linkup(1) - Indicates that the status of ONT ETH port is link up 2. linkdown(2) - Indicates that the status of ONT ETH port is link down 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT port upstream car profile id (1~1024, 0xfffe-unconcern).

OBJECT-TYPE

This object indicates the ONT port downstream car profile id (1~1024, 0xfffe-unconcern).

OBJECT-TYPE

This object indicates the ONT port upstream car profile name.

OBJECT-TYPE

This object indicates the ONT port downstream car profile name.

OBJECT-TYPE

The ONT TDM port config table. The index of this table is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntTDMPortId.

OBJECT-TYPE

The ONT TDM port config table. The index of this entry is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntTDMPortId.

OBJECT-TYPE

This object indicates the ONT TDM port ID.

OBJECT-TYPE

This object indicates the switch of the port. Options: 1. on(1) - Indicates that the switch of the port is on 2. off(2) - Indicates that the switch of the port is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The ONT POTS port config table. The index of this table is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntPOTSPortId.

OBJECT-TYPE

The ONT POTS port config table. The index of this entry is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntPOTSPortId.

OBJECT-TYPE

This object indicates the ONT POTS port ID.

OBJECT-TYPE

This object indicates the ONT POTS port switch. Options: 1. on(1) - Indicates that the switch of the ONT POTS port is on 2. off(2) - Indicates that the switch of the ONT POTS port is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The ONT TDM port config table. The index of this table is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntTDMPortId.

OBJECT-TYPE

The ONT TDM port config table. The index of this entry is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntTDMPortId.

OBJECT-TYPE

This object indicates the ONT TDM port ID.

OBJECT-TYPE

This object indicates the ONT TDM port state. Options: 1. normal (1) - Indicates that the ONT TDM port state is normal 2. los (2) - Indicates that the ONT TDM port state is LOS 3. ais(3) - Indicates that the ONT TDM port state is AIS 4. lof(4) - Indicates that the ONT TDM port state is LOF 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

ONT TDM port enable switch. Options: 1. enable(1) - Enable the ONT TDM port switch 2. disable(2) - Disable the ONT TDM port switch 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The ont port's remote native vlan info table. The index of this table is a combination of ifIndex, hwEponDeviceOntIndex, hwEponDeviceOntPortType and hwEponDeviceOntPortId.

OBJECT-TYPE

The ont port's remote native vlan info table. The index of this entry is a combination of ifIndex, hwEponDeviceOntIndex, hwEponDeviceOntPortType and hwEponDeviceOntPortId.

OBJECT-TYPE

This object indicates the ont port's type. The value 24 indicates the FE port. The value 34 indicates the GE port. The value 47 indicates the ETH port.

OBJECT-TYPE

This object indicates the ont port ID.

OBJECT-TYPE

This object indicates the vlan mode of ont's port. Options: 1. transparent(0) - Indicates that the vlan mode of ont's port is transparent 2. tag(1) - Indicates that the vlan mode of ont's port is tag 3. translation(2) - Indicates that the vlan mode of ont's port is translation 4. aggregation(3) - Indicates that the vlan mode of ont's port is aggregation 5. trunk(4) - Indicates that the vlan mode of ont's port is trunk 6. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ont port's native vlan TPID.

OBJECT-TYPE

This object indicates the ont port's native vlan CFI.

OBJECT-TYPE

This object indicates the ont port's native vlan priority.

OBJECT-TYPE

This object indicates the ont port's native VLAN ID.

OBJECT-TYPE

This table is used to display the configuration information about VLAN switching pair of the ONT port. The index of this table is a combination of ifIndex, hwEponDeviceOntIndex, hwEponDeviceOntPortType, hwEponDeviceOntPortId and hwEponDeviceOntPortVlanIndex.

OBJECT-TYPE

This table is used to display the configuration information about VLAN switching pair of the ONT port. The index of this entry is a combination of ifIndex, hwEponDeviceOntIndex, hwEponDeviceOntPortType, hwEponDeviceOntPortId and hwEponDeviceOntPortVlanIndex.

OBJECT-TYPE

This object indicates the vlan index.

OBJECT-TYPE

This object indicates the ont port's vlan TPID.

OBJECT-TYPE

This object indicates the ont port's vlan CFI.

OBJECT-TYPE

This object indicates the ont port's vlan priority.

OBJECT-TYPE

This object indicates the ont port's VLAN ID.

OBJECT-TYPE

This object indicates the ont port's vlan TPID.

OBJECT-TYPE

This object indicates the ont port's vlan CFI.

OBJECT-TYPE

This object indicates the ont port's vlan priority.

OBJECT-TYPE

This object indicates the ont port's VLAN ID.

OBJECT-TYPE

This table is used to display the ONT multicast control list. The index of this table is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntMultiCtrItemIndex.

OBJECT-TYPE

This table is used to display the ONT multicast control list. The index of this entry is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntMultiCtrItemIndex.

OBJECT-TYPE

This object indicates the item's index.

OBJECT-TYPE

This object indicates the multicast contrl type. Options: 1. gda(0) - Based GDA MAC only 2. gdaVLAN(1) - Based GDA MAC plus muliticast VLAN ID 3. gdaSA(2) - Based GDA MAC plus SA MAC 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the user ID of multicast.

OBJECT-TYPE

This object indicates the GDA of multicast control.

OBJECT-TYPE

This object indicates the SA of multicast control.

OBJECT-TYPE

This is the ONT SNMP static route configuration table. This table is used to configure and query the SNMP route configuration of an ONT. The index of this table is a combination of ifIndex, hwXponDeviceOntIndex and hwGponOntObjectSnmpStaticRouteIndex.

OBJECT-TYPE

This is the ONT SNMP static route configuration table. This table is used to configure and query the SNMP route configuration of an ONT. The index of this entry is a combination of ifIndex, hwXponDeviceOntIndex and hwGponOntObjectSnmpStaticRouteIndex.

OBJECT-TYPE

This object indicates the ONT SNMP static route table index.

OBJECT-TYPE

This object indicates the IP address.

OBJECT-TYPE

This object indicates the subnet mask of the IP address.

OBJECT-TYPE

This object indicates the next hop IP address.

OBJECT-TYPE

The hwGponOntObjectSnmpStaticRouteRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates the output portid.

OBJECT-TYPE

This table is used to save the ont's register info, less than 10 times. The index of this table is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntRegisterInfoIndex.

OBJECT-TYPE

This table is used to save the ont's register info, less than 10 times. The index of this entry is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceOntRegisterInfoIndex.

OBJECT-TYPE

This object indicates the ONT register information index.

OBJECT-TYPE

This object indicates the authentication mode for the ONT. The value (1) indicates that the mode is SN or MAC. The value (2) indicates that the mode is the combination of SN and PASSWORD or combination of MAC and PASSWORD. The value (3) indicates that the mode is PASSWORD and the type is always on. The value (4) indicates that the mode is PASSWORD and the type is once on. The value (5) indicates that the mode is LOID and the type is always on. The value (6) indicates that the mode is LOID and the type is once on. The value (7) indicates that the mode is the combination of LOID and CHECKCODE ,and the type is always on. The value (8) indicates that the mode is the combination of LOID and CHECKCODE ,and the type is once on. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the ONT serial number.

OBJECT-TYPE

This object indicates the ONT password GPON password size (0..10) XG-PON password size (0..36)

OBJECT-TYPE

This object indicates the ONT type

OBJECT-TYPE

This object indicates the time when the ONT went online.

OBJECT-TYPE

This object indicates the time when the ONT went offline.

OBJECT-TYPE

This object indicates the reason why the ONT went offline. Options: 1. ontdeleted(0) - The cause of ONT's down is that the ont is deleted 2. linkeddown(1) - The cause of ONT's down is that the ont is disconnected 3. losi(2) - The cause of ONT's down is LOSi(Loss of signal for ONUi) or LOBi (Loss of burst for ONUi) 4. lofi(3) - The cause of ONT's down is that the ont is lofi(OLT can not receive expected optical frame from ONT) 5. sfi(4) - The cause of ONT's down is that the ont is sfi(Signal fail of ONUi) 6. loai(5) - The cause of ONT's down is that the ont is loai(Loss of acknowledge with ONUi) 7. loami(6) - The cause of ONT's down is that the ont is loami(Loss of PLOAM for ONUi) 8. disablefail(7) - The cause of ONT's down is that the ont fails to be deactivated 9. deactivated(8) - The cause of ONT's down is that the ont is deactivated 10. reset(9) - The cause of ONT's down is that the ont is reseted 11. reregister(10) - The cause of ONT's down is that the ont is registered again 12. popupfail(11) - The cause of ONT's down is that the ont popup test fails 13. authfail(12) - The cause of ONT's down is that the ont authentication fails 14. powerdown(13) - The cause of ONT's down is that the ont is powered off 15. reserved(14) - Reserved 16. loki(15) - The cause of ONT's down is that the ont is loki(Loss of key synch with ONUi) 17. ringDeactivated(18) - The cause of ONT's down is that the ont is deactivated due to the ring 18. turnOffOptic(30) - The cause of ONT's down is that the ont optical module is shut down 19. cmdReboot(31) - The cause of ONT's down is that the ont is reset by ont command 20. ontResetkeyReboot(32) - The cause of ONT's down is that the ont is reset by ont reset button 21. ontSoftwareReset(33) - The cause of ONT's down is that the ont is reset by ont software 22. broadcastAttackDeactivated(34) - The cause of ONT's down is that the ont is deactivated due to broadcast attack 23. operatorCheckFail(35) - The cause of ONT's down is that operator check fail 24. ontOltIncompatible(36) - The cause of ONT's down is that the ont is incompatible with the OLT 25. rogueOntselfDetected(37) - The cause of ONT's down is that the rogue ont detected by itself 26. autoIsolateReset(38) - The cause of ONT's down is that the ont resets to prevent rogue ont attacks 27. autoIsolateDeact(39) - The cause of ONT's down is that the ont is deactivated to prevent rogue ont attacks 28. ontNotInWhiteList(40) - The cause of ONT's down is that the ont is not in the white list 29. noerror(255) - The cause of ONT's down is that the ont is noerror 30. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT LOID.

OBJECT-TYPE

This object indicates the ONT CHECKCODE.

OBJECT-TYPE

This is the ONT SNMP static route configuration table. This table is used to configure and query the SNMP route configuration of an ONT. The index of this table is a combination of ifIndex, hwXponDeviceOntIndex and hwEponOntSnmpStaticRouteIndex.

OBJECT-TYPE

This is the ONT SNMP static route configuration table. This table is used to configure and query the SNMP route configuration of an ONT. The index of this entry is a combination of ifIndex, hwXponDeviceOntIndex and hwEponOntSnmpStaticRouteIndex.

OBJECT-TYPE

This object indicates the ONT SNMP static route table index.

OBJECT-TYPE

This object indicates the IP address.

OBJECT-TYPE

This object indicates the subnet mask of the IP address.

OBJECT-TYPE

This object indicates the next hop IP address.

OBJECT-TYPE

The hwEponOntSnmpStaticRouteRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This table is used to save the ONT's register info, less than 10 times. The index of this table is a combination of ifIndex, hwXponDeviceOntIndex and hwEponDeviceOntRegisterInfoIndex.

OBJECT-TYPE

This table is used to save the ONT's register info, less than 10 times. The index of this entry is a combination of ifIndex, hwXponDeviceOntIndex and hwEponDeviceOntRegisterInfoIndex.

OBJECT-TYPE

This object indicates the ONT register information index.

OBJECT-TYPE

This object indicates the authentication mode for the ONT. Options: 1. mac(1) - The authentication mode is MAC 2. macpassword(2) - The authentication mode is MAC and password 3. alwayson(3) - The authentication mode is always on 4. onceon(4) - The authentication mode is once on 5. lOIDonceon(5) - The authentication mode is LOID and once on 6. lOIDalwayson(6) - The authentication mode is LOID and always on 7. lOIDCheckCodeOnceon(7) - The authentication mode is LOID, checkcode and once on 8. lOIDCheckCodeAlwayson(8) - The authentication mode is LOID, checkcode and once always on 9. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the ONT MAC address.

OBJECT-TYPE

This object indicates the ONT password.

OBJECT-TYPE

This object indicates the ONT type.

OBJECT-TYPE

This object indicates the time when the ONT goes online.

OBJECT-TYPE

This object indicates the time when the ONT goes offline.

OBJECT-TYPE

This object indicates the reason why the ONT goes offline. Options: 1. ontdeleted(0) - The cause of ONT's down is that the ont is deleted 2. linkeddown(1) - The cause of ONT's down is that the ont is disconnected 3. losi(2) - The cause of ONT's down is that the ont is losi(OLT can not receive expected optical signals from ONT) 4. lofi(3) - The cause of ONT's down is that the ont is lofi(OLT can not receive expected optical frame from ONT) 5. sfi(4) - The cause of ONT's down is that the ont is sfi(Signal fail of ONUi) 6. loai(5) - The cause of ONT's down is that the ont is loai(Loss of acknowledge with ONUi) 7. loami(6) - The cause of ONT's down is that the ont is loami(Loss of PLOAM for ONUi) 8. disablefail(7) - The cause of ONT's down is that the ont fails to be deactivated 9. deactivated(8) - The cause of ONT's down is that the ont is deactivated 10. reset(9) - The cause of ONT's down is that the ont is reseted 11. reregister(10) - The cause of ONT's down is that the ont is registered again 12. popupfail(11) - The cause of ONT's down is that the ont popup test fails 13. authfail(12) - The cause of ONT's down is that the ont authentication fails 14. powerdown(13) - The cause of ONT's down is that the ont is powered off 15. reserved(14) - Reserved 16. loki(15) - The cause of ONT's down is that the ont is loki(Loss of key synch with ONUi) 17. ringDeactivated(18) - The cause of ONT's down is that the ont is deactivated due to the ring 18. broadcastAttackDeactivated(34) - The cause of ONT's down is that the ont is deactivated due to broadcast attack 19. noerror(255) - The cause of ONT's down is that the ont is noerror 20. invalid(-1) - Indicates that the query fails or no information is detected 21. rogueOntselfDetected(37) - The cause of ONT's down is that the rogue ont detected by itself 22. antirogueontautoisolatereset(38) - The cause of ONT's down is to prevent rogue ONT attacks by reset ONT 23. antirogueontautoisolatedeactive(39) - The cause of ONT's down is to prevent rogue ONT attacks by deactive ONT

OBJECT-TYPE

This object indicates the ONT LOID.

OBJECT-TYPE

This object indicates the ONT CHECKCODE

OBJECT-TYPE

This table is used to query the information about the optical transceiver of the ONT. The index of this table is a combination of ifIndex and hwXponDeviceOntIndex.

OBJECT-TYPE

This table is used to query the information about the optical transceiver of the ONT. The index of this entry is a combination of ifIndex and hwXponDeviceOntIndex.

OBJECT-TYPE

The ONT optical power received on the OLT, unit dBm. The relationship between the actual value and the value get from this leaf node is as follows, Actual value = ((Node value - 10000) / 100)

OBJECT-TYPE

This object indicates the temperature of the optical module.

OBJECT-TYPE

This object indicates the Bias Current of the optical module.

OBJECT-TYPE

This object indicates the transmitting power of the optical module.

OBJECT-TYPE

This object indicates the receiving power of the optical module.

OBJECT-TYPE

This object indicates the Power feed voltage of the optical module.

OBJECT-TYPE

This object indicates the transmitting power of the ont peer optical module.

OBJECT-TYPE

This table is the type B dual-homing configuration table. The index of this table is ifIndex.

OBJECT-TYPE

This table is the type B dual-homing configuration table. The index of this entry is ifIndex.

OBJECT-TYPE

This object indicates whether to add a port to the protection group. Options: 1.joinwork(1) - Add the port as a working port to the protection group 2.joinprotect(2) - Add the port as a protection port to the protection group 3.undojoin(3) - Delete the memer port of the protection group 4.invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates whether the protection group is in the frozen state. Options: 1. freeze(1) - Freeze the protection group 2. undofreeze(2) - Undo the frozen state of the protection group 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates whether the port is in the forced working mode. Options: 1. force(1) - The port is in the forced working mode 2. undoforce(2) - The port is not in the forced working mode 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to set or show the port protect status. Options: 1. active(1) - The port protect status is active 2. standby(2) - The port protect status is standby 3. fault(3) - The port protect status is fault 4. detect(4) - The port protect status is detective 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the duration of the protection group member in the detect state.

OBJECT-TYPE

This object indicates the description of the member port of the protection group.

OBJECT-TYPE

This table is used to query dynamic MAC address. The index of this table is a combination of ifIndex, hwXponDynamicMacVlanId, hwXponDynamicMacIndex, hwXponDynamicMacQueryType, hwXponDynamicMacQueryPara0, hwXponDynamicMacQueryPara1, hwXponDynamicMacQueryPara2 and hwXponDynamicMacQueryPara3.

OBJECT-TYPE

This table is used to query dynamic MAC address. The index of this entry is a combination of ifIndex, hwXponDynamicMacVlanId, hwXponDynamicMacIndex, hwXponDynamicMacQueryType, hwXponDynamicMacQueryPara0, hwXponDynamicMacQueryPara1, hwXponDynamicMacQueryPara2 and hwXponDynamicMacQueryPara3.

OBJECT-TYPE

This object indicates the VLAN of dynamic MAC address. The value(-1) is invalid value.

OBJECT-TYPE

This object indicates the dynamic MAC address index.

OBJECT-TYPE

This object indicates the query type. Options: 1. xponOntPortInSpecVlan(1) - The ONT port is in the specified vlan 2. xponOntInSpecPort(2) - The specified ONT port 3. xponOntInSpecOnt(3) - The specified ONT 4. xponOntInSpecWlan(4) - The WLAN of specified ONT

OBJECT-TYPE

This object indicates the ONT ID, range: 0~254.

OBJECT-TYPE

This object indicates the type of the ONT port.

OBJECT-TYPE

This object indicates the port ID of the ONT.

OBJECT-TYPE

This object indicates the Fourth reserved Parameter of HwXponDynamicMacQueryEntry.

OBJECT-TYPE

MAC address. When hwXponDynamicMacQueryType is 1 ,the MAC addresses which can include 5 MAC addresses at most, and its format is (XX.XX.XX.XX.XX.XX). When hwXponDynamicMacQueryType is 2, 3 or 4, the query result contains MAC address entries with a length of 0-1280 bytes. A maximum of 128 MAC addresses can be queried, each entry containing 10 bytes. The queried entry is in a format of port type (1 byte)+port ID (1 byte)+VLAN ID (2 bytes)+MAC address (6 bytes), where the blank field can be represented by 0, for example, 3401400000E0FC000001. Range: 0-1280

OBJECT-TYPE

This is the unbound GEM port query table in the profile mode. The index of this table is a combination of ifIndex and hwGponDeviceUnboundGemPortId.

OBJECT-TYPE

This is the unbound GEM port query table in the profile mode. The index of this entry is a combination of ifIndex and hwGponDeviceUnboundGemPortId.

OBJECT-TYPE

This object indicates the unbound GEM port ID.

OBJECT-TYPE

This object indicates the carried service type of the unbound GEM port. Options: 1. tdm(1) - TDM 2. omci(2) - OMCI 3. eth(3) - ETH 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the downstream encryption switch of the unbound GEM port. Options: 1. on(1) - Indicates that the downstream encryption switch of the unbound GEM port is on 2. off(2) - Indicates that the downstream encryption switch of the unbound GEM port is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the subtending attribute of the unbound GEM port. Options: 1. on(1) - Indicates that the subtending attribute of the unbound GEM port is on 2. off(2) - Indicates that the subtending attribute of the unbound GEM port is off 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the unbound GEM port description.

OBJECT-TYPE

The hwGponDeviceUnboundGemPortEntryStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This is ONT GEM port configuration table. This table is used to configure the mapping relation between the T-CONT and GEM port of an ONT. The index of this table is a combination of ifIndex and hwGponDeviceOntGemPortBindGemPortId.

OBJECT-TYPE

This is ONT GEM port configuration table. This table is used to configure the mapping relation between the T-CONT and GEM port of an ONT. The index of this entry is a combination of ifIndex and hwGponDeviceOntGemPortBindGemPortId.

OBJECT-TYPE

This object indicates the ONT GEM Port ID.

OBJECT-TYPE

This object indicates the ONT ID. If the value of the ACCESS clause is 'write-only', then the value of the MAX-ACCESS clause MUST be 'read-write', and the DESCRIPTION clause SHALL note that reading this object will result in implementation-specific results.

OBJECT-TYPE

This object indicates the T-CONT ID. If the value of the ACCESS clause is 'write-only', then the value of the MAX-ACCESS clause MUST be 'read-write', and the DESCRIPTION clause SHALL note that reading this object will result in implementation-specific results.

OBJECT-TYPE

This object indicates the up stream priority-queue index. If the value of the ACCESS clause is 'write-only', then the value of the MAX-ACCESS clause MUST be 'read-write', and the DESCRIPTION clause SHALL note that reading this object will result in implementation-specific results.

OBJECT-TYPE

This object indicates the traffic table id of the GEM port. If the value of the ACCESS clause is 'write-only', then the value of the MAX-ACCESS clause MUST be 'read-write', and the DESCRIPTION clause SHALL note that reading this object will result in implementation-specific results.

OBJECT-TYPE

The hwGponDeviceOntGemPortBindEntryStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates the down stream priority-queue index. 0..7: Down Stream PQ index. 254 : Apaptive, Gemport Down Stream PQ is decided by ont. -1 : Default Value.Gemport Down Stream PQ is decided by olt.

OBJECT-TYPE

This object indicates the traffic table name of the GEM port.

OBJECT-TYPE

This is TCONTS configuration table in gpon mode. This table is used to configure these TCONTS which are not binded dba-profile. The index of this table is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceLineProfTcontRefIndex.

OBJECT-TYPE

This is TCONTS configuration table in gpon mode. This table is used to configure these TCONTS which are not binded dba-profile. The index of this entry is a combination of ifIndex, hwGponDeviceOntIndex and hwGponDeviceLineProfTcontRefIndex.

OBJECT-TYPE

This object indicates the TCONT Index.

OBJECT-TYPE

This object indicates the dba-profile name.

OBJECT-TYPE

This object indicates the alloc ID.

OBJECT-TYPE

The hwGponDeviceLineProfTcontRefEntryStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This is the rogue ONT list table. The index of this table is ifIndex.

OBJECT-TYPE

This is the rogue ONT list table. The index of this entry is ifIndex.

OBJECT-TYPE

This object indicates the rogue ont list.

OBJECT-TYPE

This is the ONT LLID related configuration table. The index of this table is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntLlidIndex.

OBJECT-TYPE

This is the ONT LLID related configuration table. The index of this entry is a combination of ifIndex, hwEponDeviceOntIndex and hwEponDeviceOntLlidIndex.

OBJECT-TYPE

This object indicates the EPON line profile LLID config Llid index.

OBJECT-TYPE

This object indicates the value of Logical Link Identifier.

OBJECT-TYPE

This object indicates the name of the DBA profile.

OBJECT-TYPE

This object indicates the ONT Llid car profile id (1~1024, 0xfffe-unconcern).

OBJECT-TYPE

This object indicates the ONT Llid car profile name.

OBJECT-TYPE

This is the ONT port vlan configuration table. The index of this table is a combination of ifIndex, hwEponOntPortVlanCfgOntPhyType, hwEponDeviceOntIndex, hwEponOntPortVlanCfgOntPhyIndex and hwEponOntPortVlanCfgCVlan.

OBJECT-TYPE

This is the ONT port vlan configuration table. The index of this entry is a combination of ifIndex, hwEponOntPortVlanCfgOntPhyType, hwEponDeviceOntIndex, hwEponOntPortVlanCfgOntPhyIndex and hwEponOntPortVlanCfgCVlan.

OBJECT-TYPE

This object indicates the port type of the ONT. Options: 1. t1(13) - T1 2. e1(14) - E1 3. fe(24) - FE 4. ge(34) - GE 5. moca(46) - MOCA 6. eth(47) - ETH 7. iphost(50) - IPHOST

OBJECT-TYPE

This object indicates the port index of the ONT.

OBJECT-TYPE

This object indicates the epon ont port customer vlan. When the vlan mode is transparent, should input 65534 (0xfffe).

OBJECT-TYPE

This object indicates the epon ont port service vlan.

OBJECT-TYPE

This object indicates the xpon service profile port vlan type. Options: 1. transparent(1) - Indicates that the XPON service profile port vlan type is transparent 2. translation(2) - Indicates that the XPON service profile port vlan type is translation 3. invalid(-1) - Indicates that the XPON service profile port vlan type is invalid

OBJECT-TYPE

Row status. This object is used to differentiate the creation, modification and deletion operations for an object. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This table is used to create, delete, modify or query the EPON alarm profile. The index of this table is hwEponDeviceAlarmProfileInfoNameIndex.

OBJECT-TYPE

This table is used to create, delete, modify or query the EPON alarm profile. The index of this entry is hwEponDeviceAlarmProfileInfoNameIndex.

OBJECT-TYPE

This object indicates the name of EPON alarm profile.

OBJECT-TYPE

This object indicates the bind number of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream drop events threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream drop events restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream drop events threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream drop events restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream CRC error frames threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream CRC error frames restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream CRC error frames threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream CRC error frames restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream under size frames threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream under size frames restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream under size frames threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream under size frames restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream over size frames threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream over size frames restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream over size frames threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream over size frames restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream fragments threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream fragments restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream fragments threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream fragments restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream jabbers threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream jabbers restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream jabbers threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream jabbers restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream discards threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream discards restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream discards threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream discards restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream errors threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the down stream errors restore threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream errors threshold of EPON alarm profile.

OBJECT-TYPE

This object indicates the up stream errors restore threshold of EPON alarm profile.

OBJECT-TYPE

This object is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This table is used to create, delete, modify or query GPON ONT's distributed port vlan. The index of this table is ifIndex, hwGponDeviceOntIndex, hwGponDeviceOntPortVlanPhyType, hwGponDeviceOntPortVlanPhyIndex, hwGponDeviceOntPortVlanCVlan, hwGponDeviceOntPortVlanCPri, hwGponDeviceOntPortVlanEtherType.

OBJECT-TYPE

This table is used to create, delete, modify or query GPON ONT's distributed port vlan. The index of this entry is ifIndex, hwGponDeviceOntIndex, hwGponDeviceOntPortVlanPhyType, hwGponDeviceOntPortVlanPhyIndex, hwGponDeviceOntPortVlanCVlan, hwGponDeviceOntPortVlanCPri, hwGponDeviceOntPortVlanEtherType.

OBJECT-TYPE

This object indicates the port type of the ONT. Options: 1. t1(13) - T1 2. e1(14) - E1 3. fe(24) - FE 4. ge(34) - GE 5. vdsl(37) - VDSL 6. wifi(40) - WiFi 7. moca(46) - MOCA 8. eth(47) - ETH 9. iphost(50) - IPHOST

OBJECT-TYPE

This object indicates the port index of the ONT.

OBJECT-TYPE

This object indicates the port customer vlan distributed configured on GPON ONT. When the vlan mode is transparent, the custom vlan should be 65534 (0xfffe). When the vlan type is q-in-q and user vlan attribute is untagged, custom vlan should be 0xfffd(65533).

OBJECT-TYPE

This object indicates the port translation or qinq c-priority distributed configured on GPON ONT.

OBJECT-TYPE

This object indicates customer service encapsulation type distributed configured on GPON ONT. Options: 1. ipv4-ipoe(1) - Indicates that the customer service encapsulation type is ipv4 ipoe 2. pppoe(2) - Indicates that the customer service encapsulation type is pppoe 3. ipv6-ipoe(4) - Indicates that the customer service encapsulation type is ipv6 ipoe 4. invalid(-1) - Indicates that don't specify the customer service encapsulation type 5. 0x600-0xffff - Indicates that the customer service encapsulation type is user-defined

OBJECT-TYPE

This object indicates the port vlan type distributed configured on GPON ONT. Options: 1. transparent(1) - Indicates that the port vlan type distributed configured on GPON ONT is transparent 2. translation(2) - Indicates that the port vlan type distributed configured on GPON ONT is translation distributed configured on GPON ONT 3. qinq(3) - Indicates that the port vlan type distributed configured on GPON ONT is qinq 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the port service vlan distributed configured on GPON ONT.

OBJECT-TYPE

This object indicates the port translation or qinq s-priority distributed configured on GPON ONT.

OBJECT-TYPE

This object indicates the s-vlan priority policy distributed configured on GPON ONT. Options: 1. specify(1) - Indicates that the s-vlan priority policy is specified 2. userCos(2) - Indicates that the s-vlan priority policy is userCos 3. dscpMapping(3) - Indicates that the s-vlan priority policy is dscpMapping 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the default priority for dscpMapping policy.

OBJECT-TYPE

The hwGponDeviceOntPortVlanRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-IDENTITY

OBJECT-TYPE

This is the DBA profile table. This table is used to create a DBA profile, and is used to modify or delete a DBA profile which is not bound. The index of this table is hwXponDeviceDbaProfileInfoNameIndex.

OBJECT-TYPE

This is the DBA profile table. This table is used to create a DBA profile, and is used to modify or delete a DBA profile which is not bound. The index of this entry is hwXponDeviceDbaProfileInfoNameIndex.

OBJECT-TYPE

This object indicates the DBA profile name.

OBJECT-TYPE

This object indicates the DBA profile type. The value (1) indicates that the DBA profile type is Type 1. The value (2) indicates that the DBA profile type is Type 2. The value (3) indicates that the DBA profile type is Type 3. The value (4) indicates that the DBA profile type is Type 4. The value (5) indicates that the DBA profile type is Type 5. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the fixed bandwidth of the profile, unit Kbps. The value (0) is invalid value.

OBJECT-TYPE

This object indicates the assured bandwidth of the profile, unit Kbps. The value (0) is invalid value.

OBJECT-TYPE

This object indicates the max bandwidth of the profile, unit Kbps. The value (0) is invalid value.

OBJECT-TYPE

This object indicates the binding times of the profile.

OBJECT-TYPE

This object indicates the bandwidth compensation policy of the profile. Options: 1. enable(1) - Enable the bandwidth compensation policy of the profile 2. disable(2) - Disable the bandwidth compensation policy of the profile

OBJECT-TYPE

The hwXponDeviceDbaProfileEntryStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

Fix delay switch of the profile. Options: 1. enable(1) -Fix delay switch of the profile is enable 2. disable(2) -Fix delay switch of the profile is disable

OBJECT-TYPE

Additional bandwidth type of the profile. Options: 1. nonAssure(1) -Additional bandwidth type of the profile is non assure 2. bestEffort(2) -Additional bandwidth type of the profile is best effort 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object is used to set best effort bandwidth assignment priority. Ranging from 0 to 7, 0 is the lowest priority. The default value is 0.

OBJECT-TYPE

This object is used to set best effort bandwidth assignment weight. Ranging from 1 to 10000. The default value is 128.

OBJECT-TYPE

This object indicates the commit result of a DBA profile, the aging time of the result is 20s. Options: This node identifies the result of DBA profile commit: Value 0 indicates the commit result is successfully. Value 1~0xFFFFFFFF-2 indicates the commit result is fail and return error code. Value 0xFFFFFFFD indicates that the commit does not complete Value 0xFFFFFFFE indicates that no commit is being operated Value 0xFFFFFFFF indicates invalid

OBJECT-TYPE

This object indicates the mode of commit of a DBA profile Options: 1. asynMode (1) - Indicates that the commit mode is asynchronous 2. invalid(-1) - Invalid value The device will perform sync mode without the mib node.

OBJECT-TYPE

This table is the SNMP parameter management profile of the ONT. The index of this table is hwXponDeviceOntSnmpProfileInfoNameIndex.

OBJECT-TYPE

This table is the SNMP parameter management profile of the ONT. The index of this entry is hwXponDeviceOntSnmpProfileInfoNameIndex.

OBJECT-TYPE

This object indicates the ONT SNMP profile name.

OBJECT-TYPE

This object indicates the SNMP version number. Options: 1. v1(1) - Indicates that the SNMP version is v1 2. v2c(2) - Indicates that the SNMP version is v2c 3. v3(3) - Indicates that the SNMP version is v3 The default value is v1(1).

OBJECT-TYPE

This object indicates the name of the read community.

OBJECT-TYPE

This object indicates the name of the write community.

OBJECT-TYPE

This object indicates the target host address of sending trap msg.

OBJECT-TYPE

This object indicates the ID of the host UDP source port from which the trap is sent.

OBJECT-TYPE

This object indicates the securityname of SNMP msg

OBJECT-TYPE

The hwXponDeviceOntSnmpProfileRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

The name of the SNMPv3 user.

OBJECT-TYPE

This object indicates the user authentication mode. When the version of the SNMP profile is v1 or v2c, the invalid value will be returned. Options: 1. none(1) - No authentication mode 2. hmacMd5(2) - Hmac-md5 authentication mode 3. hmacSha(3) - Hmac-sha authentication mode 4. invalid(255) - Invalid value

OBJECT-TYPE

The authentication password.

OBJECT-TYPE

This object indicates the user encryption mode. When the version of the SNMP profile is v1 or v2c, the invalid value will be returned. Options: 1. none(1) - No encryption mode 2. des56(2) - 56-bit DES encryption mode 3. tripleDes(3) - 3DES encryption mode 4. aes128(4) - 128-bit AES encryption mode 5. aes192(20) - 192-bit AES encryption mode 6. aes256(21) - 256-bit AES encryption mode 7. invalid(255) - Invalid value

OBJECT-TYPE

The encryption password.

OBJECT-TYPE

This object indicates the trap security level. When the version of the SNMP profile is v1 or v2c, the invalid value will be returned. Options: 1. privacy(1) - Authenticate and encrypt the SNMPv3 trap packet 2. authentication(2) - Authenticate but not encrypt the SNMPv3 trap packet 3. noauthnopriv(3) - Not authenticate nor encrypt the SNMPv3 trap packet 4. invalid(255) - Invalid value

OBJECT-TYPE

The configuration table of the XPON classification. The index of this table is a combination of hwXponDeviceOntPortClassProfileIdIndex, hwXponDeviceOntPortClassPrecedenceIndex and hwXponDeviceOntPortClassConditionIndex.

OBJECT-TYPE

The configuration table of the XPON classification. The index of this entry is a combination of hwXponDeviceOntPortClassProfileIdIndex, hwXponDeviceOntPortClassPrecedenceIndex and hwXponDeviceOntPortClassConditionIndex.

OBJECT-TYPE

This object indicates the profile index.

OBJECT-TYPE

This object indicates the precedence-rule

OBJECT-TYPE

This object indicates the conditionindex-condition.

OBJECT-TYPE

This object indicates the profile binding times.

OBJECT-TYPE

This object indicates the profile name.

OBJECT-TYPE

This object indicates the mapping queue. The valid value range is 0~255. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the priority mark. The valid value range is 0~7,255. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the field selected corresponding the condition. The value (0) indicates that the field is classified by destination MAC. The value (1) indicates that the field is classified by source MAC. The value (2) indicates that the field is classified by ethernet user priority. The value (3) indicates that the field is classified by VLAN ID. The value (4) indicates that the field is classified by ETH type. The value (5) indicates that the field is classified by destination IPv4 address. The value (6) indicates that the field is classified by source IPv4 address. The value (7) indicates that the field is classified by IP protocol type. The value (8) indicates that the field is classified by IPv4 DSCP. The value (9) indicates that the field is classified by IPv6 DSCP. The value (10) indicates that the field is classified by source port of layer 4 protocol. The value (11) indicates that the field is classified by destination port of layer 4 protocol. The value (12) indicates that the field is classified by IP version. The value (13) indicates that the field is classified by IPv6 flow label. The value (14) indicates that the field is classified by destination IPv6 address. The value (15) indicates that the field is classified by source IPv6 address. The value (16) indicates that the field is classified by prefix of destination IPv6 address. The value (17) indicates that the field is classified by prefix of source IPv6 address. The value (18) indicates that the field is classified by IPv6 next header. The value (-1) indicates that the query fails or no information is detected.

OBJECT-TYPE

This object indicates the operator flag. The value (0) indicates that the operator flag is never match. The value (1) indicates that the operator flag is equal. The value (2) indicates that the operator flag is not equal. The value (3) indicates that the operator flag is less than or equal. The value (4) indicates that the operator flag is greater or equal. The value (5) indicates that the operator flag is true if field exists. The value (6) indicates that the operator flag is true if field not exist. The value (7) indicates that the operator flag is always match. The value (-1) indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the match values.

OBJECT-TYPE

The hwXponDeviceOntPortClassProfileRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This is the EPON line profile table. This table is used to create a EPON line profile. The index of this table is hwEponDeviceLineProfileInfoNameIndex.

OBJECT-TYPE

This is the EPON line profile table. This table is used to create a EPON line profile. The index of this entry is hwEponDeviceLineProfileInfoNameIndex.

OBJECT-TYPE

This object indicates the EPON line profile name index.

OBJECT-TYPE

This object indicates the number of ONT bound with EPON line profile.

OBJECT-TYPE

This object indicates the EPON line profile FEC switch. Options: 1. enable (1) - Enable the EPON line profile FEC switch 2. disable (2) - Disable the EPON line profile FEC switch 3. invalid (-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the EPON line profile configuration commit. Options: 1. commitExecute(1) - Execute the EPON line profile configuration commit 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The hwEponDeviceLineProfileRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

The index of IP host which used by TR069.

OBJECT-TYPE

This is the XPON line profile LLID config table. This table is used to configure epon LLID. The index of this table is a combination of hwEponLineProfLlidCfgLineProfNameIndex, and hwEponLineProfLlidCfgLlidIndex.

OBJECT-TYPE

This is the XPON line profile LLID config table. This table is used to configure epon LLID. The index of this entry is a combination of hwEponLineProfLlidCfgLineProfNameIndex, and hwEponLineProfLlidCfgLlidIndex.

OBJECT-TYPE

This object indicates the XPON line profile name index.

OBJECT-TYPE

This object indicates the XPON line profile LLID config Llid index.

OBJECT-TYPE

This object indicates the XPON line profile LLID config car profile index(1~1024, 0xfffe-unconcern).

OBJECT-TYPE

This object indicates the XPON line profile LLID config DBA profile name.

OBJECT-TYPE

This object indicates the XPON line profile LLID config gem encryp mode. Options: 1. aes128(1) - Indicates that the XPON line profile LLID config gem encrypt mode is aes128 2. triplechurning(2) - Indicates that the XPON line profile LLID config gem encrypt mode is triple churning 3. off(3) - Indicates that the XPON line profile LLID config gem encrypt mode is off

OBJECT-TYPE

This object indicates the XPON line profile LLID config queue-set-1 report bitmap.

OBJECT-TYPE

This object indicates the XPON line profile LLID config queue-set-1 threshold value.

OBJECT-TYPE

This object indicates the XPON line profile LLID config queue-set-2 report bitmap.

OBJECT-TYPE

This object indicates the XPON line profile LLID config queue-set-2 threshold value.

OBJECT-TYPE

This object indicates the XPON line profile LLID config queue-set-3 report bitmap.

OBJECT-TYPE

This object indicates the XPON line profile LLID config queue-set-3 threshold value.

OBJECT-TYPE

The hwEponLineProfLlidCfgRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates the XPON line profile LLID config car profile name.

OBJECT-TYPE

This is the EPON service profile table. The index of this table is hwEponDeviceSrvProfileInfoNameIndex.

OBJECT-TYPE

This is the EPON service profile table. The index of this entry is hwEponDeviceSrvProfileInfoNameIndex.

OBJECT-TYPE

This object indicates the EPON line profile name index.

OBJECT-TYPE

This object indicates the number of ONT bound with EPON service profile.

OBJECT-TYPE

This object indicates the EPON service profile configuration commit. Options: 1. commitExecute(1) - Execute the EPON service profile configuration commit 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The hwEponDeviceSrvProfileRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This is the EPON service profile ont config table. The index of this table is hwEponDeviceSrvProfOntCfgSrvProfNameIndex.

OBJECT-TYPE

This is the EPON service profile ont config table. The index of this entry is hwEponDeviceSrvProfOntCfgSrvProfNameIndex.

OBJECT-TYPE

This object indicates the EPON service profile name index.

OBJECT-TYPE

This object indicates the XPON service profile pots port number. A special value of 0xFE (254) indicates the number of port is adaptive.

OBJECT-TYPE

This object indicates the XPON service profile eth port number. A special value of 0xFE (254) indicates the number of port is adaptive.

OBJECT-TYPE

This object indicates the XPON service profile tdm port number.

OBJECT-TYPE

This object indicates the XPON service profile tdm port type. Options: 1. t1(13) - T1 2. e1(14) - E1 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile multicast mode. Options: 1. ctc(1) - Indicates that the XPON service profile multicast mode is CTC 2. igmpsnooping(2) - Indicates that the XPON service profile multicast mode is igmp snooping 3. transparent(3) - Indicates that the XPON service profile multicast mode is transparent 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile multicast quick leave switch. Options: 1. enable(1) - Enable the XPON service profile multicast quick leave switch 2. disable(2) - Disable the XPON service profile multicast quick leave switch 3. unconcern(254) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile ring check function switch. Options: 1. enable(1) - Enable the XPON service profile ring check function switch 2. disable(2) - Disable the XPON service profile ring check function switch 3. unconcern(254) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile ring check auto shutdown function switch Options: 1. enable(1) - Indicates that the XPON service profile ring check auto shutdown switch enable. 2. disable(2) - Indicates that the XPON service profile ring check auto shutdown switch disable. 3. unconcern(254) - Indicates that the XPON service profile ring check auto shutdown switch unconcern.

OBJECT-TYPE

This object indicates the max number of adaptive pots ports. Range: 1-32. 32 is default value.

OBJECT-TYPE

This object indicates the max number of adaptive eth ports. Range: 1-24. 8 is default value.

OBJECT-TYPE

This is the EPON service profile multicast vlan config table. The index of this table is a combination of hwEponDeviceSrvProfMulticastVlanCfgSrvProfNameIndex, hwEponDeviceSrvProfMulticastVlanCfgOntPhyType, hwEponDeviceSrvProfMulticastVlanCfgOntPhyIndex and hwEponDeviceSrvProfMulticastVlanCfgMulticastVlan.

OBJECT-TYPE

This is the EPON service profile multicast vlan config table. The index of this entry is a combination of hwEponDeviceSrvProfMulticastVlanCfgSrvProfNameIndex, hwEponDeviceSrvProfMulticastVlanCfgOntPhyType, hwEponDeviceSrvProfMulticastVlanCfgOntPhyIndex and hwEponDeviceSrvProfMulticastVlanCfgMulticastVlan.

OBJECT-TYPE

This object indicates the XPON service profile name index.

OBJECT-TYPE

This object indicates the port type of the ONT. Options: 1. t1(13) - T1 2. e1(14) - E1 3. fe(24) - FE 4. ge(34) - GE 5. moca(46) - MOCA 6. eth(47) - ETH 7. iphost(50) - IPHOST

OBJECT-TYPE

This object indicates the port index of the ONT

OBJECT-TYPE

This object indicates the EPON service profile multicast vlan.

OBJECT-TYPE

The hwEponDeviceSrvProfMulticastVlanCfgRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates the EPON service profile multicast translated VLAN.

OBJECT-TYPE

This is the EPON service profile port vlan config table. The index of this table is a combination of hwEponDeviceSrvProfPortVlanCfgSrvProfNameIndex, hwEponDeviceSrvProfPortVlanCfgOntPhyType, hwEponDeviceSrvProfPortVlanCfgOntPhyIndex and hwEponDeviceSrvProfPortVlanCfgPortCVlan.

OBJECT-TYPE

This is the EPON service profile port vlan config table. The index of this entry is a combination of hwEponDeviceSrvProfPortVlanCfgSrvProfNameIndex, hwEponDeviceSrvProfPortVlanCfgOntPhyType, hwEponDeviceSrvProfPortVlanCfgOntPhyIndex and hwEponDeviceSrvProfPortVlanCfgPortCVlan.

OBJECT-TYPE

This object indicates the XPON service profile name index.

OBJECT-TYPE

This object indicates the port type of the ONT. Options: 1. t1(13) - T1 2. e1(14) - E1 3. fe(24) - FE 4. ge(34) - GE 5. moca(46) - MOCA 6. eth(47) - ETH 7. iphost(50) - IPHOST

OBJECT-TYPE

This object indicates the port index of the ONT.

OBJECT-TYPE

This object indicates the XPON service profile port vlan type. Options: 1. transparent(1) - Indicates that the XPON service profile port vlan type is transparent 2. translation(2) - Indicates that the XPON service profile port vlan type is translation 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the EPON service profile port customer vlan. The value 65534 indicates that the vlan mode of ont's port is transparent.

OBJECT-TYPE

This object indicates the EPON service profile port service vlan. The value(-1) is invalid value.

OBJECT-TYPE

The hwEponDeviceSrvProfPortVlanCfgRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This is the EPON service profile ont port config table. The index of this table is a combination of hwEponDeviceSrvProfOntPortCfgSrvProfNameIndex, hwEponDeviceSrvProfOntPortCfgOntPhyType and hwEponDeviceSrvProfOntPortCfgOntPhyIndex.

OBJECT-TYPE

This is the EPON service profile ont port config table. The index of this entry is a combination of hwEponDeviceSrvProfOntPortCfgSrvProfNameIndex, hwEponDeviceSrvProfOntPortCfgOntPhyType and hwEponDeviceSrvProfOntPortCfgOntPhyIndex.

OBJECT-TYPE

This object indicates the XPON service profile name index.

OBJECT-TYPE

This object indicates the port type of the ONT. Options: 1. t1(13) - T1 2. e1(14) - E1 3. fe(24) - FE 4. ge(34) - GE 5. moca(46) - MOCA 6. eth(47) - ETH 7. iphost(50) - IPHOST

OBJECT-TYPE

This object indicates the port index of the ONT.

OBJECT-TYPE

This object indicates the XPON service profile ont port up-stream car profile id.

OBJECT-TYPE

This object indicates the XPON service profile ont port down-stream car profile id.

OBJECT-TYPE

This object indicates the XPON service profile ont port max mac-address number.

OBJECT-TYPE

This object indicates the XPON service profile port config class profile index.

OBJECT-TYPE

This object indicates the XPON service profile multicast strip switch. Options: 1. tag(1) - Indicates that the XPON service profile multicast strip switch is tag 2. untag(2) - Indicates that the XPON service profile multicast strip switch is untag 3. translation(3) - Indicates that the XPON service profile multicast strip switch is translation 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the max multicast group num on port.

OBJECT-TYPE

This object indicates the XPON service profile ont port up-stream car profile name.

OBJECT-TYPE

This object indicates the XPON service profile ont port down-stream car profile name.

OBJECT-TYPE

This is the GPON line profile table. This table is used to create a GPON line profile. The index of this table is hwGponDeviceLineProfileInfoNameIndex.

OBJECT-TYPE

This is the GPON line profile table. This table is used to create a GPON line profile. The index of this entry is hwGponDeviceLineProfileInfoNameIndex.

OBJECT-TYPE

This object indicates the GPON line profile name index.

OBJECT-TYPE

This object indicates the number of ONT bound with GPON line profile.

OBJECT-TYPE

This object indicates the GPON line profile upstream FEC. Options: 1. enable (1) - Enable the GPON line profile upstream FEC 2. disable (2) - Disable the GPON line profile upstream FEC

OBJECT-TYPE

This object indicates the GPON line profile mapping mode. Options: 1. vlan(1) - The GPON line profile mapping mode is vlan 2. pri8021p(2) - The GPON line profile mapping mode is 802.1p 3. vlanpri(3) - The GPON line profile mapping mode is vlan and 802.1p 4. port(4) - The GPON line profile mapping mode is port 5. vlanport(5) - The GPON line profile mapping mode is vlan and port 6. portpri(6) - The GPON line profile mapping mode is port and 802.1p 7. vlanpriport(7) - The GPON line profile mapping mode is vlan, port and 802.1p 8. e1t1(8) - The GPON line profile mapping mode is the port of e1 and t1 9. iptos(9) - The GPON line profile mapping mode is iptos 10. vlaniptos(10) - The GPON line profile mapping mode is vlan and iptos 11. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the GPON line profile QOS mode. Options: 1. pq(1) - The GPON line profile QOS mode is PQ 2. gemcar(2) - The GPON line profile QOS mode is the gemcar 3. flowcar(3) - The GPON line profile QOS mode is the flowcar

OBJECT-TYPE

This object indicates the GPON Line Profile Configuration Commit. Options: 1. commitExecute(1) - Execute the GPON line profile configuration commit 2. clearResult(2) - Clear the commit result 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The hwGponDeviceLineProfileRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates the GPON line profile OMCC downstream encrypt status. Options: 1. on(1) - Indicates that the GPON line profile OMCC downstream encrypt status is on 2. off(2) - Indicates that the GPON line profile OMCC downstream encrypt status is off

OBJECT-TYPE

This object indicates the GPON line profile tr069 management status. Options: 1. enable(1) - Enable the GPON line profile tr069 management status 2. disable(2) - Disable the GPON line profile tr069 management status

OBJECT-TYPE

This object indicates the commit result of a GPON line profile, the aging time of the result is 20s. Options: 1. success(1) - Indicates that the commit result is success 2. fail(2) - Indicates that the commit result is fail 3. operating(3) - Indicates that the commit does not complete 4. invalid(-1) - Indicates that no commit is being operated

OBJECT-TYPE

The index of IP host which used by TR069.

OBJECT-TYPE

This is the XPON line profile tcont config table. This table is used to configure tcont. The index of this table is a combination of hwGponDeviceLineProfTcontCfgLineProfNameIndex, and hwGponDeviceLineProfTcontCfgTcontIndex.

OBJECT-TYPE

This is the XPON line profile tcont config table. This table is used to configure tcont. The index of this entry is a combination of hwGponDeviceLineProfTcontCfgLineProfNameIndex, and hwGponDeviceLineProfTcontCfgTcontIndex.

OBJECT-TYPE

This object indicates the XPON line profile name index.

OBJECT-TYPE

This object indicates the XPON line profile tcont index.

OBJECT-TYPE

This object indicates the XPON line profile tcont config DBA profile name.

OBJECT-TYPE

The hwGponDeviceLineProfTcontCfgRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This is the XPON line profile gem config table. This table is used to configure gem. The index of this table is a combination of hwGponDeviceLineProfGemCfgLineProfNameIndex and hwGponDeviceLineProfGemCfgGemIndex.

OBJECT-TYPE

This is the XPON line profile gem config table. This table is used to configure gem. The index of this entry is a combination of hwGponDeviceLineProfGemCfgLineProfNameIndex and hwGponDeviceLineProfGemCfgGemIndex.

OBJECT-TYPE

This object indicates the XPON line profile name index.

OBJECT-TYPE

This object indicates the XPON line profile gem config gem index.

OBJECT-TYPE

This object indicates the XPON line profile gem config car profile index.

OBJECT-TYPE

This object indicates the XPON line profile gem config bind tcont index.

OBJECT-TYPE

This object indicates the XPON line profile gem config gem service type. Options: 1. eth(1) - ETH 2. tdm(2) - TDM

OBJECT-TYPE

This object indicates the XPON line profile gem config gem encrypt mode. Options: 1. on(1) - Indicates that the XPON line profile gem config gem encrypt mode is on 2. off(2) - Indicates that the XPON line profile gem config gem encrypt mode is off

OBJECT-TYPE

This object indicates the XPON line profile gem config gem cascade switch. Options: 1. on(1) - Indicates that the XPON line profile gem config gem cascade switch is on 2. off(2) - Indicates that the XPON line profile gem config gem cascade switch is off

OBJECT-TYPE

This object indicates the XPON line profile gem config up stream PQ index.

OBJECT-TYPE

The hwGponDeviceLineProfGemCfgRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates the XPON line profile gem config down stream PQ index. 0..7: Down Stream PQ index, 254 : Apaptive, Gemport Down Stream PQ is decided by ont. -1 : Default Value.Gemport Down Stream PQ is decided by olt.

OBJECT-TYPE

This object indicates the XPON line profile gem config car profile name.

OBJECT-TYPE

This is the XPON line profile flow config table. This table is used to configure gem mapping to service. The index of this table is a combination of hwGponDeviceLineProfMappingCfgLineProfNameIndex, hwGponDeviceLineProfMappingCfgGemIndex and hwGponDeviceLineProfMappingCfgMappingIndex.

OBJECT-TYPE

This is the XPON line profile flow config table. This table is used to configure gem mapping to service. The index of this entry is a combination of hwGponDeviceLineProfMappingCfgLineProfNameIndex, hwGponDeviceLineProfMappingCfgGemIndex and hwGponDeviceLineProfMappingCfgMappingIndex.

OBJECT-TYPE

This object indicates the XPON line profile name index.

OBJECT-TYPE

This object indicates the XPON line profile mapping config gem index.

OBJECT-TYPE

This object indicates the XPON line profile mapping config flow index.

OBJECT-TYPE

This object indicates the XPON line profile mapping config mapping mode. Options: 1. vlan(1) - The XPON line profile mapping mode is vlan 2. pri8021p(2) - The XPON line profile mapping mode is 802.1p 3. vlanpri(3) - The XPON line profile mapping mode is vlan and 802.1p 4. port(4) - The XPON line profile mapping mode is port 5. vlanport(5) - The XPON line profile mapping mode is vlan and port 6. portpri(6) - The XPON line profile mapping mode is port and 802.1p 7. vlanpriport(7) - The XPON line profile mapping mode is vlan, port and 802.1p 8. e1t1port(8) - The XPON line profile mapping mode is the port of e1 and t1 9. iptos(9) - The XPON line profile mapping mode is iptos 10. vlaniptos(10) - The XPON line profile mapping mode is vlan and iptos 11. invalid(-1) - Indicates that the mapping port type is tdm-vcl

OBJECT-TYPE

This object indicates the XPON line profile mapping config car profile index.

OBJECT-TYPE

This object indicates the port type of the ONT. Options: 1. t1(13) - T1 2. e1(14) - E1 3. fe(24) - FE 4. ge(34) - GE 5. vdsl(37) - VDSL 6. moca(46) - MOCA 7. eth(47) - ETH 8. iphost(50) - IPHOST 9. ippath(61) - Ippath 10. tdmvcl(253) - Tdmvcl 11. ethBundle(254) - EthBundle 12. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the port index of the ONT, or the bundle-groupid when it is the eth-bundle port type.

OBJECT-TYPE

This object indicates the VLAN ID of the service. The value -1 indicates invalid VLAN ID, and 65533 indicates untag traffic stream.

OBJECT-TYPE

This object indicates the priority of the service.

OBJECT-TYPE

The hwGponDeviceLineProfMappingCfgRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This object indicates the flow transparent switch of the ONT. Options: 1. enable(1) - Enable the flow transparent switch of the ONT 2. disable(2) - Disable the flow transparent switch of the ONT 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON line profile mapping config car profile name.

OBJECT-TYPE

This is the GPON service profile table. The index of this table is hwGponDeviceSrvProfileInfoNameIndex.

OBJECT-TYPE

This is the GPON service profile table. The index of this entry is hwGponDeviceSrvProfileInfoNameIndex.

OBJECT-TYPE

This object indicates the GPON service profile name index.

OBJECT-TYPE

This object indicates the number of ONT bound with GPON service profile.

OBJECT-TYPE

This object indicates the GPON service profile configuration commit. Options: 1. commitExecute(1) - Execute the GPON service profile configuration commit 2. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The hwGponDeviceSrvProfileRowStatus is used to create a new row or to modify or delete an existing row in this table. Options: 1. createAndGo(4) -create a new instance of a conceptual row 2. destroy(6) -delete the instances associated with an existing conceptual row

OBJECT-TYPE

This is GPON service profile ont config table. The index of this table is hwGponDeviceSrvProfOntCfgSrvProfNameIndex.

OBJECT-TYPE

This is GPON service profile ont config table. The index of this entry is hwGponDeviceSrvProfOntCfgSrvProfNameIndex.

OBJECT-TYPE

This object indicates the XPON service profile name index.

OBJECT-TYPE

This object indicates the XPON service profile pots port number. A special value of 0xFE (254) indicates the number of port is adaptive.

OBJECT-TYPE

This object indicates the XPON service profile eth port number. A special value of 0xFE (254) indicates the number of port is adaptive.

OBJECT-TYPE

This object indicates the XPON service profile tdm port number.

OBJECT-TYPE

This object indicates the XPON service profile tdm port type. Options: 1. t1(13) - T1 2. e1(14) - E1 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile tdm port service type. Options: 1. tdmovergem(1) - Tdm over gem 2. cesop(2) - Cesop

OBJECT-TYPE

This object indicates the XPON service profile MOCA port number.

OBJECT-TYPE

This object indicates the XPON service profile catv port number. A special value of 0xFE (254) indicates the number of port is adaptive.

OBJECT-TYPE

This object indicates the XPON service profile mac address switch. Options: 1. enable(1) - Enable the XPON service profile mac address switch 2. disable(2) - Disable the XPON service profile mac address switch 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile transparent switch. Options: 1. enable(1) - Enable the XPON service profile transparent switch 2. disable(2) - Disable the XPON service profile transparent switch 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile igmp transmit mode. Options: 1. tagtranslation(1) - Indicates that the XPON service profile igmp transmit mode is tag translation 2. tagtransparent(2) - Indicates that the XPON service profile igmp transmit mode is tag transparent 3. untag(3) - Indicates that the XPON service profile igmp transmit mode is untag 4. unconcern(254) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile multicast vlan. value 4096 indicates IGMP-user-VLAN is used for multicast vlan.

OBJECT-TYPE

This object indicates the XPON service profile multicast mode. Options: 1. oltcontrol(1) - Indicates that the XPON service profile multicast mode is olt controled 2. igmpsnooping(2) - Indicates that the XPON service profile multicast mode is igmp snooping 3. unconcern(254) - Indicates that the XPON service profile multicast mode is not concerned

OBJECT-TYPE

This object indicates the XPON service profile upstream igmp packets forward mode. Options: 1. transparent(1) - Indicates that the XPON service profile upstream igmp packets forward mode is transparent 2. translation(2) - Indicates that the XPON service profile upstream igmp packets forward mode is translation 3. default(3) - Indicates that the XPON service profile upstream igmp packets forward mode is default 4. unconcern(254) - Indicates that the XPON service profile upstream igmp packets forward mode is not concerned 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

XPON service profile upstream igmp packets will be translate to the translation vlan, if upstream igmp packets forward mode is translation(2).

OBJECT-TYPE

When xpon service profile upstream igmp packets were added a vlan or translated to the translation vlan, priority was set.

OBJECT-TYPE

This object indicates the XPON service profile native VLAN. Options: 1. concern(1) - Concern the XPON service profile native VLAN 2. unconcern(2) - Unconcern the XPON service profile native VLAN

OBJECT-TYPE

This object indicates the GPON service profile upstream priority-queue color policy. Options: 1. noMarking(0) - Indicates that the upstream priority-queue color policy is no marking 2. dei(2) - Indicates that the upstream priority-queue color policy is DEI 3. invalid(-1) - Indicates that the upstream priority-queue color policy is invalid

OBJECT-TYPE

This object indicates the GPON service profile downstream priority-queue color policy. Options: 1. noMarking(0) - Indicates that the downstream priority-queue color policy is no marking 2. dei(2) - Indicates that the downstream priority-queue color policy is DEI 3. invalid(-1) - Indicates that the downstream priority-queue color policy is invalid

OBJECT-TYPE

This object indicates the XPON service profile VDSL port number. A special value of 0xFE (254) indicates the number of port is adaptive.

OBJECT-TYPE

This object indicates the XPON service profile mac address switch. Options: 1. enable(1) - Enable the XPON service profile ring check switch 2. disable(2) - Disable the XPON service profile ring check switch 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile mac address switch. Options: 1. enable(1) - Enable the XPON service profile ring check auto shutdown switch 2. disable(2) - Disable the XPON service profile ring check auto shutdown switch 3. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the XPON service profile ring check detecting frequency.

OBJECT-TYPE

This object indicates the XPON service profile ring check resume frequency.

OBJECT-TYPE

This object indicates the max number of adaptive pots ports. Range: 1-32. 32 is default value.

OBJECT-TYPE

This object indicates the max number of adaptive eth ports. Range: 1-24. 8 is default value.

OBJECT-TYPE

This object indicates the max number of adaptive vdsl ports. Range: 1-8. 8 is default value.

OBJECT-TYPE

This object indicates the max number of adaptive catv ports. Range: 1-8. 8 is default value.

OBJECT-TYPE

This object indicates the XPON service profile WiFi port number. Range: 0-4. 0 is default value.

OBJECT-TYPE

The switch of the ONT Monitor Link function. Options: 1. enable(1) -Enable the the ONT Monitor Link function 2. disable(2) -Disable the the ONT Monitor Link function 3. unconcern (254) -The ONT Monitor Link function is unconcern and depends on ONT Configuration.The default value is unconcern.

OBJECT-TYPE

This object indicates the ONT MTU value. Unit:byte. The value (0) indicates that the MTU value is decided by ONT. The value (-1) indicates that the query fails or no information is detected. The default value is unconcern(0).

OBJECT-TYPE

This is the GPON service profile ont port config table. The index of this table is a combination of hwGponDeviceSrvProfOntPortCfgSrvProfNameIndex, hwGponDeviceSrvProfOntPortCfgOntPhyType and hwGponDeviceSrvProfOntPortCfgOntPhyIndex.

OBJECT-TYPE

This is the GPON service profile ont port config table. The index of this entry is a combination of hwGponDeviceSrvProfOntPortCfgSrvProfNameIndex, hwGponDeviceSrvProfOntPortCfgOntPhyType and hwGponDeviceSrvProfOntPortCfgOntPhyIndex.

OBJECT-TYPE

XPON service profile name index.

OBJECT-TYPE

This object indicates the port type of the ONT. Options: 1. t1(13) - T1 2. e1(14) - E1 3. fe(24) - FE 4. ge(34) - GE 5. vdsl(37) - VDSL 6. moca(46) - MOCA 7. eth(47) - ETH 8. iphost(50) - IPHOST

OBJECT-TYPE

This object indicates the port index of the ONT.

OBJECT-TYPE

This object indicates the XPON service profile tdm port coding mode. Options: 1. ami(1) - AMI 2. hdb3(2) - HDB3 3. b8zs(3) - B8ZS 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the QinQ mode. Options: 1. disable(1) - Disable the QinQ mode 2. enable(2) - Enable the QinQ mode 3. unconcern(254) - The QinQ mode is not concerned 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

This object indicates the priority policy. Options: 1. assigned(1) - The priority policy is assigned 2. copycos(2) - The priority policy is copy CoS 3. unconcern(254) - The priority policy is not concerned 4. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The upstream car profile index of the ONT port.

OBJECT-TYPE

The downstream car profile index of the ONT port.

OBJECT-TYPE

The dscp profile index of the ONT port.

OBJECT-TYPE

This object indicates the upstream igmp packets transmit mode profile of GPON ONT port. Options: 1. transparent(1) - Indicates that the GPON ONT port upstream igmp packets transmit mode profile is transparent 2. translation(2) - Indicates that the GPON ONT port upstream igmp packets transmit mode profile is translation 3. default(3) - Indicates that the GPON ONT port upstream igmp packets transmit mode profile is default 4. disable(254) - Indicates that the GPON ONT port upstream igmp packets transmit mode profile configured will be cancelled 5. invalid(-1) - Indicates that the query fails or no information is detected

OBJECT-TYPE

The GPON ONT port upstream igmp packets will be translate to the translation vlan, if GPON ONT port upstream igmp packets forward mode is translation(2) or default(3).

OBJECT-TYPE

When GPON ONT port upstream igmp packets were added a vlan or translated to the translation vlan, priority was set.

OBJECT-TYPE

This object indicates the maximum number of MAC addresses that can be learned on each ONT port. The number of MAC addresses learned on an ONT port should not greater than this number. range:0~255. 4294967295 is invalid value. 0 is default value, means unlimited.