HUAWEI-RSVPTE-MIB
- Registered at
- 1.3.6.1.4.1.2011.5.25.148
- Last updated
- 2007-04-10 10:00
- Organization
- Huawei Technologies Co.,Ltd.
- Namespace
- huawei
- Source file
HUAWEI-RSVPTE-MIB- Digest
sha256:3f7a1b958e59ce00f4e9e534f861318fb188c4df661fd955571898d61e603c6c
Description
The MIB module to describe the RSVP Protocol
Contact
R&D BeiJing, Huawei Technologies co.,Ltd. Huawei Bld.,NO.3 Xinxi Rd., Shang-Di Information Industry Base, Hai-Dian District Beijing P.R. China Zip:100085 Http://www.huawei.com E-mail:support@huawei.com
Imports
| From | Symbols |
|---|---|
| HUAWEI-MIB | hwDatacomm |
| IF-MIB | ifIndex |
| INTEGRATED-SERVICES-MIB | BitRate, BurstSize, MessageSize, QosService, SessionType |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Gauge32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DisplayString, RowStatus, TEXTUAL-CONVENTION, TimeInterval, TimeStamp, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
HUAWEI-MIB HUAWEI-RSVPTE-MIB IANAifType-MIB IF-MIB INTEGRATED-SERVICES-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| hwRsvpTeObjects OBJECT-IDENTITY | 1.3.6.1.4.1.2011.5.25.148.1 | |||
| hwRsvpTeSessionTable OBJECT-TYPE A table of all sessions seen by a given sys- tem. | 1.3.6.1.4.1.2011.5.25.148.1.1 | not-accessible | current | |
| hwRsvpTeSessionEntry OBJECT-TYPE A single session seen by a given system. | 1.3.6.1.4.1.2011.5.25.148.1.1.1 | not-accessible | current | |
| hwRsvpTeSessionNumber OBJECT-TYPE The number of this session. This is for SNMP Indexing purposes only and has no relation to any protocol value. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.1 | Gauge32 | not-accessible | current |
| hwRsvpTeSessionType OBJECT-TYPE The type of session (IP4, IP6, IP6 with flow information, etc). | 1.3.6.1.4.1.2011.5.25.148.1.1.1.2 | SessionType | read-only | current |
| hwRsvpTeSessionDestAddr OBJECT-TYPE The destination address used by all senders in this session. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.3 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeSessionDestAddrLength OBJECT-TYPE The CIDR prefix length of the session address, which is 32 for IP4 host and multicast ad- dresses, and 128 for IP6 addresses. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.4 | Integer32 | read-only | current |
| hwRsvpTeSessionSenders OBJECT-TYPE The number of distinct senders currently known to be part of this session. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.5 | Gauge32 | read-only | current |
| hwRsvpTeSessionReceivers OBJECT-TYPE The number of reservations being requested of this system for this session. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.6 | Gauge32 | read-only | current |
| hwRsvpTeSessionRequests OBJECT-TYPE The number of reservation requests this system is sending upstream for this session. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.7 | Gauge32 | read-only | current |
| hwRsvpTeSessionTunnelId OBJECT-TYPE A 16-bit identifier used in the SESSION that remains constant over the life of the tunnel. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.8 | Integer32 | read-only | current |
| hwRsvpTeSessionTunnelExtId OBJECT-TYPE An identifier used in the SESSION that remains constant over the life of the tunnel. Normally the identifier is set to all zeros. Ingress nodes that wish to narrow the scope of a SESSION to the ingress-egress pair may place their IPv4 address here as a globally unique identifier. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.9 | IpAddress | read-only | current |
| hwRsvpTeSessionLspsNumber OBJECT-TYPE The number of LSPs that belong to this session. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.10 | Gauge32 | read-only | current |
| hwRsvpTeSessionStyle OBJECT-TYPE An enumerable value to identify the treatment of reservations for different senders within the same session: WF 10001b, FF01010b, SE 10010b. | 1.3.6.1.4.1.2011.5.25.148.1.1.1.11 | INTEGER {ff(10), wf(17), se(18)} | read-only | current |
| hwRsvpTeSenderTable OBJECT-TYPE Information describing the state information displayed by senders in PATH messages. | 1.3.6.1.4.1.2011.5.25.148.1.2 | not-accessible | current | |
| hwRsvpTeSenderEntry OBJECT-TYPE Information describing the state information displayed by a single sender's PATH message. | 1.3.6.1.4.1.2011.5.25.148.1.2.1 | not-accessible | current | |
| hwRsvpTeSenderNumber OBJECT-TYPE The number of this sender. This is for SNMP Indexing purposes only and has no relation to any protocol value. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.1 | Gauge32 | not-accessible | current |
| hwRsvpTeSenderType OBJECT-TYPE The type of session (IP4, IP6, IP6 with flow information, etc). | 1.3.6.1.4.1.2011.5.25.148.1.2.1.2 | SessionType | read-only | current |
| hwRsvpTeSenderDestAddr OBJECT-TYPE The destination address used by all senders in this session. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.3 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeSenderAddr OBJECT-TYPE The source address used by this sender in this session. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.4 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeSenderDestAddrLength OBJECT-TYPE The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.5 | Integer32 | read-only | current |
| hwRsvpTeSenderAddrLength OBJECT-TYPE The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.6 | Integer32 | read-only | current |
| hwRsvpTeSenderHopAddr OBJECT-TYPE The address used by the previous RSVP hop (which may be the original sender). | 1.3.6.1.4.1.2011.5.25.148.1.2.1.7 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeSenderHopLih OBJECT-TYPE The Logical Interface Handle used by the pre- vious RSVP hop (which may be the original sender). | 1.3.6.1.4.1.2011.5.25.148.1.2.1.8 | Integer32 | read-only | current |
| hwRsvpTeSenderInterface OBJECT-TYPE The ifIndex value of the interface on which this PATH message was most recently received. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.9 | Integer32 | read-only | current |
| hwRsvpTeSenderTSpecRate OBJECT-TYPE The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeSenderTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed hwRsvpTeSen- derTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.10 | BitRate | read-only | current |
| hwRsvpTeSenderTSpecPeakRate OBJECT-TYPE The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.11 | BitRate | read-only | current |
| hwRsvpTeSenderTSpecBurst OBJECT-TYPE The size of the largest burst expected from the sender at a time. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.12 | BurstSize | read-only | current |
| hwRsvpTeSenderTSpecMinTu OBJECT-TYPE The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.13 | MessageSize | read-only | current |
| hwRsvpTeSenderTSpecMaxTu OBJECT-TYPE The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.14 | MessageSize | read-only | current |
| hwRsvpTeSenderInterval OBJECT-TYPE The interval between refresh messages as ad- vertised by the previous hop. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.15 | Integer32 | read-only | current |
| hwRsvpTeSenderRsvpHop OBJECT-TYPE If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.16 | TruthValue | read-only | current |
| hwRsvpTeSenderPolicy OBJECT-TYPE The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.17 | OCTET STRING (SIZE(0..65532)) | read-only | current |
| hwRsvpTeSenderAdspecBreak OBJECT-TYPE The global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in the path. If FALSE, no non-IS hops were detected. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.18 | TruthValue | read-only | current |
| hwRsvpTeSenderAdspecHopCount OBJECT-TYPE The hop count general characterization parame- ter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present | 1.3.6.1.4.1.2011.5.25.148.1.2.1.19 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecPathBw OBJECT-TYPE The path bandwidth estimate general character- ization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present | 1.3.6.1.4.1.2011.5.25.148.1.2.1.20 | BitRate | read-only | current |
| hwRsvpTeSenderAdspecMinLatency OBJECT-TYPE The minimum path latency general characteriza- tion parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present | 1.3.6.1.4.1.2011.5.25.148.1.2.1.21 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecMtu OBJECT-TYPE The composed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present | 1.3.6.1.4.1.2011.5.25.148.1.2.1.22 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedSvc OBJECT-TYPE If TRUE, the ADSPEC contains a Guaranteed Ser- vice fragment. If FALSE, the ADSPEC does not contain a Guaranteed Service fragment. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.23 | TruthValue | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedBreak OBJECT-TYPE If TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the guaranteed service. If FALSE, and hwRsvpTe- SenderAdspecGuaranteedSvc is TRUE, the 'break' bit is not set. If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns FALSE or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.24 | TruthValue | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedCtot OBJECT-TYPE If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.25 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedDtot OBJECT-TYPE If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.26 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedCsum OBJECT-TYPE If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'C' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.27 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedDsum OBJECT-TYPE If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the composed value for the guaranteed ser- vice 'D' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.28 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedHopCount OBJECT-TYPE If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.29 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedPathBw OBJECT-TYPE If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.30 | BitRate | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedMinLatency OBJECT-TYPE If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.31 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecGuaranteedMtu OBJECT-TYPE If hwRsvpTeSenderAdspecGuaranteedSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecGuaranteedSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.32 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecCtrlLoadSvc OBJECT-TYPE If TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load Service frag- ment. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.33 | TruthValue | read-only | current |
| hwRsvpTeSenderAdspecCtrlLoadBreak OBJECT-TYPE If TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the controlled load service. If FALSE, and hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, the 'break' bit is not set. If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns FALSE or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.34 | TruthValue | read-only | current |
| hwRsvpTeSenderAdspecCtrlLoadHopCount OBJECT-TYPE If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.35 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecCtrlLoadPathBw OBJECT-TYPE If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.36 | BitRate | read-only | current |
| hwRsvpTeSenderAdspecCtrlLoadMinLatency OBJECT-TYPE If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.37 | Integer32 | read-only | current |
| hwRsvpTeSenderAdspecCtrlLoadMtu OBJECT-TYPE If hwRsvpTeSenderAdspecCtrlLoadSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If hwRsvpTeSenderAdspecCtrlLoadSvc is FALSE, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.38 | Integer32 | read-only | current |
| hwRsvpTeSenderTtl OBJECT-TYPE The TTL value in the RSVP header that was last received. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.39 | Integer32 | read-only | current |
| hwRsvpTeLspId OBJECT-TYPE A 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.40 | Integer32 | read-only | current |
| hwRsvpTeSenderMsgIdSndFlag OBJECT-TYPE Indicates that the message sender requests the peer to send an acknowledgment for the message. (0x01: ACK desired.) | 1.3.6.1.4.1.2011.5.25.148.1.2.1.41 | Integer32 | read-only | current |
| hwRsvpTeSenderMsgIdSndEpoch OBJECT-TYPE A value that indicates when the Message_Identi- fier sequence has been reset. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.42 | Gauge32 | read-only | current |
| hwRsvpTeSenderMsgIdSndNumber OBJECT-TYPE When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the Epoch changes or when the value wraps. A return of 0 indicates the absence of the MESSAGE_ID object to be sent. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.43 | Gauge32 | read-only | current |
| hwRsvpTeSenderMsgIdRcvFlag OBJECT-TYPE The message ID flag of the message latest received. It is used to identify whether ACK is desired or not. And it can be extended. (0x01: ACK desired.) | 1.3.6.1.4.1.2011.5.25.148.1.2.1.44 | Integer32 | read-only | current |
| hwRsvpTeSenderMsgIdRcvEpoch OBJECT-TYPE The message ID epoch of the message latest received form the interface. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.45 | Gauge32 | read-only | current |
| hwRsvpTeSenderMsgIdRcvNumber OBJECT-TYPE The message ID number of the message latest received form the interface. A return of 0 indicates the absence of the MESSAGE_ID object received. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.46 | Gauge32 | read-only | current |
| hwRsvpTeSenderClassType OBJECT-TYPE Indicates the class-type. A return of zero indicates the absence of the object. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.47 | Integer32 | read-only | current |
| hwRsvpTeSenderLabelRequestCtype OBJECT-TYPE The type of label request (without label range, with ATM label range, with frame relay label range, etc). | 1.3.6.1.4.1.2011.5.25.148.1.2.1.48 | INTEGER {withoutLabelRange(1), withAtmLabelRange(2), withFrameRelayLabelRange(3)} | read-only | current |
| hwRsvpTeSenderLabelRequestL3pid OBJECT-TYPE An identifier of the layer 3 protocol using this path. Standard Ethertype values are used. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.49 | Integer32 | read-only | current |
| hwRsvpTeSenderLabelRequestAtmMinVpi OBJECT-TYPE This 12 bit field specifies the lower bound of a block of Virtual Path Identifiers that is supported on the originating switch. If the VPI is less than 12-bits it must be right justified in this field and preceding bits must be set to zero. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.50 | Integer32 | read-only | current |
| hwRsvpTeSenderLabelRequestAtmMinVci OBJECT-TYPE This 16 bit field specifies the lower bound of a block of Virtual Connection Identifiers that is supported on the originating switch. If the VCI is less than 16-bits it must be right justified in this field and preceding bits must be set to zero. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.51 | Integer32 | read-only | current |
| hwRsvpTeSenderLabelRequestAtmMaxVpi OBJECT-TYPE This 12 bit field specifies the upper bound of a block of Virtual Path Identifiers that is supported on the originating switch. If the VPI is less than 12-bits it must be right justified in this field and preceding bits must be set to zero. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.52 | Integer32 | read-only | current |
| hwRsvpTeSenderLabelRequestAtmMaxVci OBJECT-TYPE This 16 bit field specifies the upper bound of a block of Virtual Connection Identifiers that is supported on the originating switch. If the VCI is less than 16-bits it must be right justified in this field and preceding bits must be set to zero. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.53 | Integer32 | read-only | current |
| hwRsvpTeSenderLabelRequestFrMinDlci OBJECT-TYPE This 23-bit field specifies the lower bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch. The DLCI must be right justified in this field and unused bits must be set to 0. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.54 | Integer32 | read-only | current |
| hwRsvpTeSenderLabelRequestFrMaxDlci OBJECT-TYPE This 23-bit field specifies the upper bound of a block of Data Link Connection Identifiers (DLCIs) that is supported on the originating switch. The DLCI must be right justified in this field and unused bits must be set to 0. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.55 | Integer32 | read-only | current |
| hwRsvpTeSenderSessionAttrType OBJECT-TYPE The type of the session_attribute (without resource affinities or with resource affinities). | 1.3.6.1.4.1.2011.5.25.148.1.2.1.56 | INTEGER {withRa(1), withoutRa(7)} | read-only | current |
| hwRsvpTeSenderSessionAttrSetupPrio OBJECT-TYPE The priority of the session with respect to taking resources, in the range of 0 to 7. The value 0 is the highest priority. The Setup Priority is used in deciding whether this session can preempt another session. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.57 | Integer32 | read-only | current |
| hwRsvpTeSenderSessionAttrHoldPrio OBJECT-TYPE The priority of the session with respect to holding resources, in the range of 0 to 7. The value 0 is the highest priority. Holding Priority is used in deciding whether this session can be preempted by another session. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.58 | Integer32 | read-only | current |
| hwRsvpTeSenderSessionAttrFlag OBJECT-TYPE A mixed value. (0x01: Local protection desired; 0x02: Label recording desired; 0x04: SE Style desired; 0x08: bandwidth protection desired; 0x10: node protection desired; 0x20: Path re-evaluation request; 0x40: Soft preemption desired) | 1.3.6.1.4.1.2011.5.25.148.1.2.1.59 | Integer32 | read-only | current |
| hwRsvpTeSenderSessionAttrName OBJECT-TYPE Session name, a null padded string of characters. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.60 | OCTET STRING (SIZE(0..64)) | read-only | current |
| hwRsvpTeSenderSessionAttrExcludeAny OBJECT-TYPE A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link unacceptable. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.61 | Gauge32 | read-only | current |
| hwRsvpTeSenderSessionAttrIncludeAny OBJECT-TYPE A 32-bit vector representing a set of attribute filters associated with a tunnel any of which renders a link acceptable (with respect to this test). A null set (all bits set to zero) automatically passes. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.62 | Gauge32 | read-only | current |
| hwRsvpTeSenderSessionAttrIncludeAll OBJECT-TYPE A 32-bit vector representing a set of attribute filters associated with a tunnel all of which must be present for a link to be acceptable (with respect to this test). A null set (all bits set to zero) automatically passes. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.63 | Gauge32 | read-only | current |
| hwRsvpTeSenderFrrSetupPrio OBJECT-TYPE The priority of the backup path with respect to taking resources, in the range 0 to 7. The value 0 is the highest priority. Setup Priority is used in deciding whether this session can preempt another session. See [RSVP-TE] for the usage on priority. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.64 | Integer32 | read-only | current |
| hwRsvpTeSenderFrrHoldPrio OBJECT-TYPE The priority of the backup path with respect to holding resources, in the range 0 to 7. The value 0 is the highest priority. Holding Priority is used in deciding whether this session can be preempted by another session. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.65 | Integer32 | read-only | current |
| hwRsvpTeSenderFrrHopLimit OBJECT-TYPE The maximum number of extra hops the backup path is allowed to take, from current node (a PLR) to an MP, with PLR and MP excluded from the count. For example, hop-limit of 0 means that only direct links between PLR and MP can be considered. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.66 | Integer32 | read-only | current |
| hwRsvpTeSenderFrrFlag OBJECT-TYPE An enumerable value to indicate the protection schema desired (0x01, One-to-One Backup Desired; 0x02, Facility Backup Desired; 0x03, No Backup Desired). | 1.3.6.1.4.1.2011.5.25.148.1.2.1.67 | INTEGER {oneToOneDesired(1), facilityDesired(2), noBackupDesired(3)} | read-only | current |
| hwRsvpTeSenderFrrBandwidth OBJECT-TYPE Bandwidth estimate; 32-bit IEEE floating point integer, in bits per second. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.68 | BitRate | read-only | current |
| hwRsvpTeSenderFrrExcludeAny OBJECT-TYPE A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link unacceptable. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.69 | Gauge32 | read-only | current |
| hwRsvpTeSenderFrrIncludeAny OBJECT-TYPE A 32-bit vector representing a set of attribute filters associated with a backup path, any of which renders a link acceptable (with respect to this test). A null set (all bits set to zero) automatically passes. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.70 | Gauge32 | read-only | current |
| hwRsvpTeSenderFrrIncludeAll OBJECT-TYPE A 32-bit vector representing a set of attribute filters associated with a backup path, all of which must be present for a link to be acceptable (with respect to this test). A null set (all bits set to zero) automatically passes. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.71 | Gauge32 | read-only | current |
| hwRsvpTeSenderFrrInuseFlag OBJECT-TYPE An enumerable value to indicate the fast-reroute state of this sender (normal, PLR in use, MP in use, PLR in use and MP in use, under protection). | 1.3.6.1.4.1.2011.5.25.148.1.2.1.72 | INTEGER {normal(1), plrInUse(2), mpInUse(3), plrAndMpInUse(4), underProtection(5)} | read-only | current |
| hwRsvpTeSenderDiffServPsc OBJECT-TYPE This 16 bits field indicates a PHB Scheduling Class to be supported by the LSP. | 1.3.6.1.4.1.2011.5.25.148.1.2.1.73 | Integer32 | read-only | current |
| hwRsvpTeResvTable OBJECT-TYPE Information describing the state information displayed by receivers in RESV messages. | 1.3.6.1.4.1.2011.5.25.148.1.3 | not-accessible | current | |
| hwRsvpTeResvEntry OBJECT-TYPE Information describing the state information displayed by a single receiver's RESV message concerning a single sender. | 1.3.6.1.4.1.2011.5.25.148.1.3.1 | not-accessible | current | |
| hwRsvpTeResvNumber OBJECT-TYPE The number of this reservation request. This is for SNMP Indexing purposes only and has no relation to any protocol value. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.1 | Gauge32 | not-accessible | current |
| hwRsvpTeResvType OBJECT-TYPE The type of session (IP4, IP6, IP6 with flow information, etc). | 1.3.6.1.4.1.2011.5.25.148.1.3.1.2 | SessionType | read-only | current |
| hwRsvpTeResvDestAddr OBJECT-TYPE The destination address used by all senders in this session. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.3 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeResvSenderAddr OBJECT-TYPE The source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.4 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeResvDestAddrLength OBJECT-TYPE The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.5 | Integer32 | read-only | current |
| hwRsvpTeResvSenderAddrLength OBJECT-TYPE The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.6 | Integer32 | read-only | current |
| hwRsvpTeResvHopAddr OBJECT-TYPE The address used by the next RSVP hop (which may be the ultimate receiver). | 1.3.6.1.4.1.2011.5.25.148.1.3.1.7 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeResvHopLih OBJECT-TYPE The Logical Interface Handle received from the previous RSVP hop (which may be the ultimate receiver). | 1.3.6.1.4.1.2011.5.25.148.1.3.1.8 | Integer32 | read-only | current |
| hwRsvpTeResvInterface OBJECT-TYPE The ifIndex value of the interface on which this RESV message was most recently received. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.9 | Integer32 | read-only | current |
| hwRsvpTeResvService OBJECT-TYPE The QoS Service classification requested by the receiver. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.10 | QosService | read-only | current |
| hwRsvpTeResvTSpecRate OBJECT-TYPE The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeResvTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed hwRsvpTeResvTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.11 | BitRate | read-only | current |
| hwRsvpTeResvTSpecPeakRate OBJECT-TYPE The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.12 | BitRate | read-only | current |
| hwRsvpTeResvTSpecBurst OBJECT-TYPE The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.13 | BurstSize | read-only | current |
| hwRsvpTeResvTSpecMinTu OBJECT-TYPE The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.14 | MessageSize | read-only | current |
| hwRsvpTeResvTSpecMaxTu OBJECT-TYPE The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.15 | MessageSize | read-only | current |
| hwRsvpTeResvRSpecRate OBJECT-TYPE If the requested service is guaranteed, as specified by hwRsvpTeResvService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.16 | BitRate | read-only | current |
| hwRsvpTeResvRSpecSlack OBJECT-TYPE If the requested service is guaranteed, as specified by hwRsvpTeResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.17 | Integer32 | read-only | current |
| hwRsvpTeResvInterval OBJECT-TYPE The interval between refresh messages as ad- vertised by the Next Hop. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.18 | Integer32 | read-only | current |
| hwRsvpTeResvScope OBJECT-TYPE The contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. If the length is non-zero, this contains a series of IP4 or IP6 addresses. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.19 | OCTET STRING (SIZE(0..65536)) | read-only | current |
| hwRsvpTeResvShared OBJECT-TYPE If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.20 | TruthValue | read-only | current |
| hwRsvpTeResvExplicit OBJECT-TYPE If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.21 | TruthValue | read-only | current |
| hwRsvpTeResvRsvpHop OBJECT-TYPE If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.22 | TruthValue | read-only | current |
| hwRsvpTeResvPolicy OBJECT-TYPE The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.23 | OCTET STRING (SIZE(0..65536)) | read-only | current |
| hwRsvpTeResvTtl OBJECT-TYPE The TTL value in the RSVP header that was last received. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.24 | Integer32 | read-only | current |
| hwRsvpTeResvConfirm OBJECT-TYPE Receiver's address. | 1.3.6.1.4.1.2011.5.25.148.1.3.1.25 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeResvFwdTable OBJECT-TYPE Information describing the state information displayed upstream in RESV messages. | 1.3.6.1.4.1.2011.5.25.148.1.4 | not-accessible | current | |
| hwRsvpTeResvFwdEntry OBJECT-TYPE Information describing the state information displayed upstream in an RESV message concern- ing a single sender. | 1.3.6.1.4.1.2011.5.25.148.1.4.1 | not-accessible | current | |
| hwRsvpTeResvFwdNumber OBJECT-TYPE The number of this reservation request. This is for SNMP Indexing purposes only and has no relation to any protocol value. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.1 | Gauge32 | not-accessible | current |
| hwRsvpTeResvFwdType OBJECT-TYPE The type of session (IP4, IP6, IP6 with flow information, etc). | 1.3.6.1.4.1.2011.5.25.148.1.4.1.2 | SessionType | read-only | current |
| hwRsvpTeResvFwdDestAddr OBJECT-TYPE The destination address used by all senders in this session. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.3 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeResvFwdSenderAddr OBJECT-TYPE The source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.4 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeResvFwdDestAddrLength OBJECT-TYPE The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.5 | Integer32 | read-only | current |
| hwRsvpTeResvFwdSenderAddrLength OBJECT-TYPE The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.6 | Integer32 | read-only | current |
| hwRsvpTeResvFwdHopAddr OBJECT-TYPE The address of the (previous) RSVP that will receive this message. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.7 | OCTET STRING (SIZE(0..16)) | read-only | current |
| hwRsvpTeResvFwdHopLih OBJECT-TYPE The Logical Interface Handle sent to the (pre- vious) RSVP that will receive this message. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.8 | Integer32 | read-only | current |
| hwRsvpTeResvFwdInterface OBJECT-TYPE The ifIndex value of the interface on which this RESV message was most recently sent. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.9 | Integer32 | read-only | current |
| hwRsvpTeResvFwdService OBJECT-TYPE The QoS Service classification requested. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.10 | QosService | read-only | current |
| hwRsvpTeResvFwdTSpecRate OBJECT-TYPE The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as hwRsvpTeResvFwdT- SpecPeakRate (if supported by the service model);however, averaged across two or more burst intervals, the rate should not exceed hwRsvpTeResvFwdTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.11 | BitRate | read-only | current |
| hwRsvpTeResvFwdTSpecPeakRate OBJECT-TYPE The Peak Bit Rate of the sender's data stream Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.12 | BitRate | read-only | current |
| hwRsvpTeResvFwdTSpecBurst OBJECT-TYPE The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.13 | BurstSize | read-only | current |
| hwRsvpTeResvFwdTSpecMinTu OBJECT-TYPE The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.14 | MessageSize | read-only | current |
| hwRsvpTeResvFwdTSpecMaxTu OBJECT-TYPE The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.15 | MessageSize | read-only | current |
| hwRsvpTeResvFwdRSpecRate OBJECT-TYPE If the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.16 | BitRate | read-only | current |
| hwRsvpTeResvFwdRSpecSlack OBJECT-TYPE If the requested service is Guaranteed, as specified by hwRsvpTeResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.17 | Integer32 | read-only | current |
| hwRsvpTeResvFwdInterval OBJECT-TYPE The interval between refresh messages adver- tised to the Previous Hop. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.18 | Integer32 | read-only | current |
| hwRsvpTeResvFwdScope OBJECT-TYPE The contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.19 | OCTET STRING (SIZE(0..65536)) | read-only | current |
| hwRsvpTeResvFwdShared OBJECT-TYPE If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.20 | TruthValue | read-only | current |
| hwRsvpTeResvFwdExplicit OBJECT-TYPE If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.21 | TruthValue | read-only | current |
| hwRsvpTeResvFwdRsvpHop OBJECT-TYPE If TRUE, the node believes that the next IP hop is an RSVP hop. If FALSE, the node be- lieves that the next IP hop may not be an RSVP hop. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.22 | TruthValue | read-only | current |
| hwRsvpTeResvFwdPolicy OBJECT-TYPE The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.23 | OCTET STRING (SIZE(0..65536)) | read-only | current |
| hwRsvpTeResvFwdTtl OBJECT-TYPE The TTL value in the RSVP header that was last received. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.24 | Integer32 | read-only | current |
| hwRsvpTeResvFwdMsgIdFlag OBJECT-TYPE Indicates that the message sender requests the peer to send an acknowledgment for the message. (0x01: ACK desired.) | 1.3.6.1.4.1.2011.5.25.148.1.4.1.25 | Integer32 | read-only | current |
| hwRsvpTeResvFwdMsgIdEpoch OBJECT-TYPE A value that indicates when the Message_Identi- fier sequence has been reset. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.26 | Gauge32 | read-only | current |
| hwRsvpTeResvFwdMsgIdNumber OBJECT-TYPE When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the epoch changes or when the value wraps. A return of 0 indicates the absence of the MESSAGE_ID object. | 1.3.6.1.4.1.2011.5.25.148.1.4.1.27 | Gauge32 | read-only | current |
| hwRsvpTeIfTable OBJECT-TYPE The RSVP-specific attributes of the system's interfaces. | 1.3.6.1.4.1.2011.5.25.148.1.5 | not-accessible | current | |
| hwRsvpTeIfEntry OBJECT-TYPE The RSVP-specific attributes of the a given interface. | 1.3.6.1.4.1.2011.5.25.148.1.5.1 | not-accessible | current | |
| hwRsvpTeIfUdpNbrs OBJECT-TYPE The number of neighbors perceived to be using only the RSVP UDP Encapsulation. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.1 | Gauge32 | read-only | current |
| hwRsvpTeIfIpNbrs OBJECT-TYPE The number of neighbors perceived to be using only the RSVP IP Encapsulation. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.2 | Gauge32 | read-only | current |
| hwRsvpTeIfNbrs OBJECT-TYPE The number of neighbors currently perceived; this will exceed hwRsvpTeIfIpNbrs + hwRsvpTeIfUdpNbrs by the number of neighbors using both encapsu- lations. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.3 | Gauge32 | read-only | current |
| hwRsvpTeIfRefreshBlockadeMultiple OBJECT-TYPE The value of the RSVP value 'Kb', Which is the minimum number of refresh intervals that blockade state will last once entered. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.4 | Integer32 | read-only | current |
| hwRsvpTeIfRefreshMultiple OBJECT-TYPE The value of the RSVP value 'K', which is the number of refresh intervals which must elapse (minimum) before a PATH or RESV message which is not being refreshed will be aged out. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.5 | Integer32 | read-only | current |
| hwRsvpTeIfTtl OBJECT-TYPE The value of SEND_TTL used on this interface for messages this node originates. If set to zero, the node determines the TTL via other means. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.6 | Integer32 | read-only | current |
| hwRsvpTeIfRefreshInterval OBJECT-TYPE The value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given PATH or RESV message on an interface. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.7 | TimeInterval | read-only | current |
| hwRsvpTeIfRouteDelay OBJECT-TYPE The approximate period from the time a route is changed to the time a resulting message ap- pears on the interface. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.8 | TimeInterval | read-only | current |
| hwRsvpTeIfEnabled OBJECT-TYPE Its value is always TRUE, if RSVP is enabled on this Interface. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.9 | TruthValue | read-only | current |
| hwRsvpTeIfUdpRequired OBJECT-TYPE If TRUE, manual configuration forces the use of UDP encapsulation on the interface. If FALSE, UDP encapsulation is only used if hwRsvpTeI- fUdpNbrs is not zero. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.10 | TruthValue | read-only | current |
| hwRsvpTeIfStatus OBJECT-TYPE 'active' on interfaces that are configured for RSVP. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.11 | RowStatus | read-only | current |
| hwRsvpTeIfHelloEnabled OBJECT-TYPE If TRUE, RSVPTE hello is enabled on this Interface. If FALSE, RSVPTE hello is not enabled on this interface | 1.3.6.1.4.1.2011.5.25.148.1.5.1.12 | TruthValue | read-only | current |
| hwRsvpTeIfSrefreshEnabled OBJECT-TYPE If TRUE, srefresh is enabled on this interface. If FALSE, srefresh is not enabled on this interface. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.13 | TruthValue | read-only | current |
| hwRsvpTeIfSrefreshInterval OBJECT-TYPE The srefresh interval. I.e. time difference between 2 refreshes. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.14 | TimeInterval | read-only | current |
| hwRsvpTeIfRetranIncDelta OBJECT-TYPE Delta governs the speed with which the sender increases the retransmission interval. The ratio of two successive retransmission intervals is (1 + Delta). | 1.3.6.1.4.1.2011.5.25.148.1.5.1.15 | Integer32 | read-only | current |
| hwRsvpTeIfRetranInterval OBJECT-TYPE The retransmission interval. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.16 | TimeInterval | read-only | current |
| hwRsvpTeIfAuthEnabled OBJECT-TYPE If TRUE, authentication is enabled on this interface. If FALSE, authentication is not enabled on this interface. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.17 | TruthValue | read-only | current |
| hwRsvpTeIfAuthEncrypted OBJECT-TYPE This states that authentication key is encrypted or not. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.18 | TruthValue | read-only | current |
| hwRsvpTeIfAuthHandshake OBJECT-TYPE Handshaking is enabled authentications. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.19 | TruthValue | read-only | current |
| hwRsvpTeIfAuthLifeTime OBJECT-TYPE Authentication life time. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.20 | TimeInterval | read-only | current |
| hwRsvpTeIfAuthKey OBJECT-TYPE Authentication key, used for authentication processing. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.21 | OCTET STRING (SIZE(0..64)) | read-only | current |
| hwRsvpTeIfWindowSize OBJECT-TYPE Administrators can specify a message window corresponding to the worst case reordering behavior. For example, one might specify that packets reordered within a 32 message window would be accepted. If no reordering can occur, the window is set to one. The maximum value is 64. | 1.3.6.1.4.1.2011.5.25.148.1.5.1.22 | Integer32 | read-only | current |
| hwRsvpTeNbrTable OBJECT-TYPE Information describing the Neighbors of an RSVP system. | 1.3.6.1.4.1.2011.5.25.148.1.6 | not-accessible | current | |
| hwRsvpTeNbrEntry OBJECT-TYPE Information describing a single RSVP Neigh- bor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1 | not-accessible | current | |
| hwRsvpTeNbrAddress OBJECT-TYPE The IP4 or IP6 Address used by this neighbor. This object may not be changed when the value of the RowStatus object is 'active'. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.1 | OCTET STRING (SIZE(0..16)) | not-accessible | current |
| hwRsvpTeNbrProtocol OBJECT-TYPE The encapsulation being used by this neigh- bor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.2 | INTEGER {ip(1), udp(2), both(3)} | read-only | current |
| hwRsvpTeNbrStatus OBJECT-TYPE 'active' for all neighbors. This object may be used to configure neighbors. In the pres- ence of configured neighbors, the implementa- tion may (but is not required to) limit the set of valid neighbors to those configured. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.3 | RowStatus | read-only | current |
| hwRsvpTeNbrSendersNumber OBJECT-TYPE The number of senders on the neighbor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.4 | Gauge32 | read-only | current |
| hwRsvpTeNbrReceiversNumber OBJECT-TYPE The number of receivers on the neighbor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.5 | Gauge32 | read-only | current |
| hwRsvpTeNbrHelloEnabled OBJECT-TYPE If TRUE, hello is enabled on the neighbor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.6 | TruthValue | read-only | current |
| hwRsvpTeNbrHelloSrcInstance OBJECT-TYPE Source instance of the neighbor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.7 | Gauge32 | read-only | current |
| hwRsvpTeNbrHelloDstInstance OBJECT-TYPE Destination instance of the neighbor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.8 | Gauge32 | read-only | current |
| hwRsvpTeNbrHelloLostCounter OBJECT-TYPE The number of times the hello messages have been sent to the neighbor for which hello ACK has not received yet. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.9 | Gauge32 | read-only | current |
| hwRsvpTeNbrHelloType OBJECT-TYPE Hello type that is being sent to the neighbor. A return of 3[none] indicates that hello is disabled on the nbr. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.10 | INTEGER {request(1), ack(2), none(3)} | read-only | current |
| hwRsvpTeNbrGrCapability OBJECT-TYPE Gives neighbor capability to support GR or undergo GR, in case of control plane restart. A mixed value. (0x01: Self GR capability of neighbor; 0x02: GR support capability of neighbor; 0x04: Neighbor capable of receiving RecoveryPath message; 0x08: Neighbor capable of sending RecoveryPath message) | 1.3.6.1.4.1.2011.5.25.148.1.6.1.11 | Integer32 | read-only | current |
| hwRsvpTeNbrGrRestartTime OBJECT-TYPE Neighbor nodes GR restart time value. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.12 | TimeStamp | read-only | current |
| hwRsvpTeNbrGrRecoveryTime OBJECT-TYPE Neighbor nodes GR recovery time value. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.13 | TimeStamp | read-only | current |
| hwRsvpTeNbrGrStatus OBJECT-TYPE Neighbor nodes GR status. (0x01, No GR activity; 0x02, Neighbor router is supporting GR; 0x03, Neighbor router is restarting; 0x04, Restart timer is running; 0x05, Recovery timer is running; 0x06, Neighbor GR end.) | 1.3.6.1.4.1.2011.5.25.148.1.6.1.14 | INTEGER {normal(1), supporting(2), restarting(3), restartTimerRunning(4), recoveryTimerRunning(5), grEnd(6)} | read-only | current |
| hwRsvpTeNbrAuthKeyId OBJECT-TYPE Neighbor's authentication key, used for authentication processing. A return of null string indicates the absence of the item. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.15 | OCTET STRING (SIZE(0 | 6)) | read-only | current |
| hwRsvpTeNbrReductionEnabled OBJECT-TYPE If TRUE srefresh is enabled on the neighbor, else srefresh is not enabled on the neighbor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.16 | TruthValue | read-only | current |
| hwRsvpTeNbrReliabilityEnabled OBJECT-TYPE If TRUE reliability is enabled on the neighbor, else reliability is not enabled on the neighbor. | 1.3.6.1.4.1.2011.5.25.148.1.6.1.17 | TruthValue | read-only | current |
| hwRsvpTeMessageIdTable OBJECT-TYPE Information describes the MessageIds of an RSVP system. | 1.3.6.1.4.1.2011.5.25.148.1.7 | not-accessible | current | |
| hwRsvpTeMessageIdEntry OBJECT-TYPE Description. | 1.3.6.1.4.1.2011.5.25.148.1.7.1 | not-accessible | current | |
| hwRsvpTeMessageIdEpoch OBJECT-TYPE A value that indicates when the Message_Identi- fier sequence has been reset. | 1.3.6.1.4.1.2011.5.25.148.1.7.1.1 | Gauge32 | not-accessible | current |
| hwRsvpTeMessageIdNumber OBJECT-TYPE When combined with the message generator's IP address, the Message_Identifier field uniquely identifies a message. The values placed in this field change incrementally and only decrease when the epoch changes or when the value wraps. | 1.3.6.1.4.1.2011.5.25.148.1.7.1.2 | Gauge32 | not-accessible | current |
| hwRsvpTeMessageIdFlag OBJECT-TYPE A enumerable value to indicate the type of this Message_Identifier. (1: SenderIncoming; 2: SenderOutgoing; 3: Resv; 4: ResvFwd; 5: RtBuff) | 1.3.6.1.4.1.2011.5.25.148.1.7.1.3 | INTEGER {senderIncoming(1), senderOutgoing(2), resv(3), resvFwd(4), rtBuff(5)} | read-only | current |
| hwRsvpTeFilterSpecTable OBJECT-TYPE Information describes the FilterSpecs of an RSVP system. | 1.3.6.1.4.1.2011.5.25.148.1.8 | not-accessible | current | |
| hwRsvpTeFilterSpecEntry OBJECT-TYPE Description. | 1.3.6.1.4.1.2011.5.25.148.1.8.1 | not-accessible | current | |
| hwRsvpTeFilterSpecNumber OBJECT-TYPE The number of this Filter_Spec. This is for SNMP Indexing purposes only and has no relation to any protocol value. | 1.3.6.1.4.1.2011.5.25.148.1.8.1.1 | Gauge32 | not-accessible | current |
| hwRsvpTeFilterSpecLspId OBJECT-TYPE A 16-bit identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself. | 1.3.6.1.4.1.2011.5.25.148.1.8.1.2 | Integer32 | read-only | current |
| hwRsvpTeFilterSpecIngressLsrId OBJECT-TYPE IP address for a sender node. | 1.3.6.1.4.1.2011.5.25.148.1.8.1.3 | OCTET STRING | read-only | current |
| hwRsvpTeFilterSpecLabel OBJECT-TYPE The value of the label arranged by next hop. A return of 4294967295 indicates the absence of the item. | 1.3.6.1.4.1.2011.5.25.148.1.8.1.4 | Gauge32 | read-only | current |
| hwRsvpTeRroTable OBJECT-TYPE Information describes the RRO sub-objects of an RSVP system. | 1.3.6.1.4.1.2011.5.25.148.1.9 | not-accessible | current | |
| hwRsvpTeRroEntry OBJECT-TYPE Description. | 1.3.6.1.4.1.2011.5.25.148.1.9.1 | not-accessible | current | |
| hwRsvpTeRroNumber OBJECT-TYPE The number of this RRO sub-object. This is for SNMP Indexing purposes only and has no relation to any protocol value. | 1.3.6.1.4.1.2011.5.25.148.1.9.1.1 | Gauge32 | not-accessible | current |
| hwRsvpTeRroType OBJECT-TYPE An enumerable value that indicates the type of this sub-object. (0x01: IPv4 address; 0x02: IPv6 address; 0x03: Label.) | 1.3.6.1.4.1.2011.5.25.148.1.9.1.2 | INTEGER {ipv4(1), ipv6(2), label(3)} | read-only | current |
| hwRsvpTeRroIpAddr OBJECT-TYPE IP address for this sub-object if the type is 'IPv4 address' of 'IPv6 address'. A return of null string indicates the absence of the item. | 1.3.6.1.4.1.2011.5.25.148.1.9.1.3 | OCTET STRING | read-only | current |
| hwRsvpTeRroIpPrefixLen OBJECT-TYPE IP prefix length for this sub-object if the type is 'IPv4 address' of 'IPv6 address'. A return of 0 indicates the absence of the item. | 1.3.6.1.4.1.2011.5.25.148.1.9.1.4 | Integer32 | read-only | current |
| hwRsvpTeRroLabel OBJECT-TYPE The value of the label if the type is 'Label'. A return of 4294967295 indicates the absence of the item. | 1.3.6.1.4.1.2011.5.25.148.1.9.1.5 | Gauge32 | read-only | current |
| hwRsvpTeRroFlag OBJECT-TYPE If hwRsvpTeRroType is IPv4 or IPv6, it is a mixed value. (0x01: Local protection available; 0x02: Local protection in use; 0x04: bandwidth protection; 0x08: node protection; 0x10: preemption pending; 0x20: node ID.) If hwRsvpTeRroType is Label, 0x01 means global label. A return of zero indicates no bit was set. | 1.3.6.1.4.1.2011.5.25.148.1.9.1.6 | Integer32 | read-only | current |
| hwRsvpTeEroTable OBJECT-TYPE Information describes the ERO sub-objects of an RSVP system. | 1.3.6.1.4.1.2011.5.25.148.1.10 | not-accessible | current | |
| hwRsvpTeEroEntry OBJECT-TYPE Description. | 1.3.6.1.4.1.2011.5.25.148.1.10.1 | not-accessible | current | |
| hwRsvpTeEroNumber OBJECT-TYPE The number of this ERO sub-object. This is for SNMP Indexing purposes only and has no relation to any protocol value. | 1.3.6.1.4.1.2011.5.25.148.1.10.1.1 | Gauge32 | not-accessible | current |
| hwRsvpTeEroType OBJECT-TYPE An enumerable value that indicates the type of this sub-object. (0x01: IPv4 address; 0x02: IPv6 address.) | 1.3.6.1.4.1.2011.5.25.148.1.10.1.2 | INTEGER {ipv4(1), ipv6(2)} | read-only | current |
| hwRsvpTeEroIpAddr OBJECT-TYPE IP address for this sub-object. | 1.3.6.1.4.1.2011.5.25.148.1.10.1.3 | OCTET STRING | read-only | current |
| hwRsvpTeEroIpPrefixLen OBJECT-TYPE IP prefix length for this sub-object. | 1.3.6.1.4.1.2011.5.25.148.1.10.1.4 | Integer32 | read-only | current |
| hwRsvpTeConformance OBJECT-IDENTITY | 1.3.6.1.4.1.2011.5.25.148.2 | |||
| hwRsvpTeGroups OBJECT-IDENTITY | 1.3.6.1.4.1.2011.5.25.148.2.1 | |||
| hwRsvpTeCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.2011.5.25.148.2.2 |
Conformance
| Name | OID | Status |
|---|---|---|
| hwRsvpTeSessionGroup OBJECT-GROUP These objects are required for RSVP Systems. | 1.3.6.1.4.1.2011.5.25.148.2.1.1 | current |
| hwRsvpTeSenderGroup OBJECT-GROUP These objects are required for RSVP Systems. | 1.3.6.1.4.1.2011.5.25.148.2.1.2 | current |
| hwRsvpTeResvGroup OBJECT-GROUP These objects are required for RSVP Systems. | 1.3.6.1.4.1.2011.5.25.148.2.1.3 | current |
| hwRsvpTeResvFwdGroup OBJECT-GROUP These objects are optional, used for some RSVP Systems. | 1.3.6.1.4.1.2011.5.25.148.2.1.4 | current |
| hwRsvpTeIfGroup OBJECT-GROUP These objects are required for RSVP Systems. | 1.3.6.1.4.1.2011.5.25.148.2.1.5 | current |
| hwRsvpTeNbrGroup OBJECT-GROUP These objects are required for RSVP Systems. | 1.3.6.1.4.1.2011.5.25.148.2.1.6 | current |
| hwRsvpTeMessageIdGroup OBJECT-GROUP Description. | 1.3.6.1.4.1.2011.5.25.148.2.1.7 | current |
| hwRsvpTeFilterSpecGroup OBJECT-GROUP Description. | 1.3.6.1.4.1.2011.5.25.148.2.1.8 | current |
| hwRsvpTeRroGroup OBJECT-GROUP Description. | 1.3.6.1.4.1.2011.5.25.148.2.1.9 | current |
| hwRsvpTeEroGroup OBJECT-GROUP Description. | 1.3.6.1.4.1.2011.5.25.148.2.1.10 | current |
| hwRsvpTeCompliance MODULE-COMPLIANCE The compliance statement. Note that the im- plementation of this module requires implemen- tation of the Integrated Services MIB as well. | 1.3.6.1.4.1.2011.5.25.148.2.2.1 | current |