HPNSAPCI-MIB

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The major revision level of the MIB.

OBJECT-TYPE

The minor revision level of the MIB.

OBJECT-IDENTITY

OBJECT-TYPE

A table of SNMP agents that satisfy requests for this MIB.

OBJECT-TYPE

A description of the agent/agents that access PCI information.

OBJECT-TYPE

A unique index for this agent.

OBJECT-TYPE

Name of the agent/agents satisfying SNMP requests for this MIB.

OBJECT-TYPE

Version number of the agent/agents satisfying SNMP requests for this MIB.

OBJECT-TYPE

The date on which this agent was created. field octets contents range ------------------------------------------------- 1 1 years since 1900 0..255 2 2 month 1..12 3 3 day 1..31 4 4 hour 0..23 5 5 minute 0..59 6 6 second 0..59

OBJECT-IDENTITY

OBJECT-TYPE

Identifies whether PCI BIOS is present. 0 = not present, 1 = PCI BIOS present.

OBJECT-TYPE

The PCI BIOS version number: low byte = minor version, high byte = major version.

OBJECT-TYPE

Number of PCI buses in the system

OBJECT-IDENTITY

OBJECT-TYPE

A list of PCI device/functions entries.

OBJECT-TYPE

A description of an PCI device/function.

OBJECT-TYPE

The PCI Bus number that this entry describes.

OBJECT-TYPE

The PCI device or slot number that this entry describes.

OBJECT-TYPE

The PCI function that this entry describes.

OBJECT-TYPE

Identifies the manufacturer of the device. 0xFFFF is an invalid value for a vendor ID. Vendor ID Manufacturer --------- ------------ XXXX Hewlett-Packard Co.

OBJECT-TYPE

Identifies the particular device. This identier is allocated by the vendor. Device ID Description --------- ------------ XXXX Blah! Blah!

OBJECT-TYPE

Specifies a device specific revision identifier.

OBJECT-TYPE

Idendifies the layout of bytes 10h-3Fh in configuration space and whether or not the device contains multiple functions. Bit 7: 1=multi-function device, 0=single function Bit 6-0: Defines layout, 0 is only layout defined, all other values are reserved.

OBJECT-TYPE

Identifies the generic function of the device. Base Sub- Prog Class Class If. Meaning ----- ----- ----- ------- 00h Device built before Class Code definitions were finalized. 00h 00h All currently implemented devices except VGA compatible devices. 01h 00h VGA compatible device 01h Mass Storage controller 00h 00h SCSI bus controller 01h 00h IDE controller 02h 00h Floppy disk controller 03h 00h IPI bus controller 80h 00h Other mass storage controller 02h Network controller 00h 00h Ethernet controller 01h 00h Token Ring controller 02h 00h FDDI controller 80h 00h Other network controller 03h Display controller 00h 00h VGA compatible controller 01h 00h XGA controller 80h 00h Other display controller 04h Multimedia device 00h 00h Video 01h 00h Audio 80h 00h Other multimedia device 05h Memory controller 00h 00h RAM 01h 00h Flash 80h 00h Other memory controller 06h Bridge device 00h 00h Host bridge 01h 00h ISA bridge 02h 00h EISA bridge 03h 00h MC bridge 04h 00h PCI-to-PCI bridge 05h 00h PCMCIA bridge 80h 00h Other bridge device 07h-FEh Reserved FFh Device does not fit in any defined classes.

OBJECT-TYPE

Provides course control over a device's ability to generate and respond to PCI cylces. Bit Description --- ------------ 0 IO Space 1 Memory Space 2 Bus Master 3 Special Cycles 4 Memory Write and Invlaidate Enable 5 VGA Palette snoop 6 Parity Error Response 7 Wait cycle control 8 SERR# enable 9 Fast Back-to-Back Enable 10-15 Reserved

OBJECT-TYPE

Status information for PCI bus related events. Bit Description --- ------------ 0-6 Reserved 7 Fast Back-to-Back Capable 8 Data Parity Detected 9-10 DEVSEL timing; 00=fast, 01=medium, 10=slow 11 Signal Target Abort 12 Received Target Abort 13 Received Master Abort 14 Signaled System Error 15 Detected Parity Error

OBJECT-TYPE

Specifies the system cache line size in units of 32-bit words.

OBJECT-TYPE

Specifies, in units of PCI bus clocks, the value of the Latency Timer for this PCI bus master.

OBJECT-TYPE

This optional register is used for control and status of Built-in Self Test. Devices that don't support BIST must always return a value of 0. Bit Description --- ------------ 7 0=BIST not supported, 1=BIST supported 6 Wrtie a 1 to invoke BIST. Devices resets the bit when BIST is complet. Software should fail device if BIST is not complete after 2 seconds. 5-4 Reserved 3-0 0=Device passed test, non-zero= device-specific failure code.

OBJECT-TYPE

Communicates interrupt line routing information. The value in this register tells which input of the system interrupt contoller(s) the device's interrupt pin is connected to.

OBJECT-TYPE

Tells which interrupt pin the device uses.

OBJECT-TYPE

Specifies how often the device needs to gain access to the PCI bus.

OBJECT-TYPE

Specifies how long a burst period the device needs assuming a clock rate of 33MHz.

OBJECT-TYPE

Base address mapping registers for memory and IO. Refer to the PCI specification for the format.

OBJECT-TYPE

4-byte register is defined to handle the base address and size information for an expansion ROM. Bit Description --- ------------ 31-11 Expansion ROM Base Address (upper 21 bits) 10-1 Reserved 0 0 = address decoding is disabled and no access to this space are allowed. 1 = address decoding enabled.

OBJECT-TYPE

Device specific configuration space.