MIBs Depot

HPN-ICF-DOT11-RRM-MIB

Registered at
1.3.6.1.4.1.11.2.14.11.15.2.75.8
Last updated
2010-09-25 18:00
Revisions
2010-09-25 18:00, 2010-02-23 18:00, 2009-08-01 20:00, 2009-05-07 20:00, 2009-04-17 20:00, 2008-07-14 14:29
Namespace
hp
Source file
HPN-ICF-DOT11-RRM-MIB
Digest
sha256:4e9d903ef31aa33af56451ccad48e7668253794a310fe7724ac661d0b81a7ba8

Description

This MIB file is to provide the object definition of WLAN radio resource management (RRM).

Imports

FromSymbols
HPN-ICF-DOT11-REF-MIBHpnicfDot11ChannelScopeType, HpnicfDot11ObjectIDType, HpnicfDot11RadioElementIndex, HpnicfDot11RadioScopeType, HpnicfDot11RadioType, HpnicfDot11SSIDStringType, hpnicfDot11, hpnicfDot11APElementIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIInteger32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

HPN-ICF-DOT11-REF-MIB
HPN-ICF-DOT11-RRM-MIB
HPN-ICF-OID-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
hpnicfDot11RRMConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1
hpnicfDot11RRMGlobalCfgPara
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1
hpnicfDot11RRM11nMadtMaxMcs
OBJECT-TYPE
Specify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No maximum MCS index is specified for 802.11n mandatory rates by default. Besides 255, the specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.1Integer32 (0..76 | 255)read-writecurrent
hpnicfDot11RRM11nSuptMaxMcs
OBJECT-TYPE
Specify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.2Integer32 (0..76)read-writecurrent
hpnicfDot11RRM11gProtect
OBJECT-TYPE
Enable/Disable dot11g protection.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.3TruthValueread-writecurrent
hpnicfDot11RRM11aPwrConstrt
OBJECT-TYPE
Configure the power constraint for all 802.11a radios. The configured power constraint is advertised in beacons if spectrum management is enabled. The range of power constraint is 0 to MAX-POWER-1 (where the MAX-POWER is defined by the regulatory domain).
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.4Integer32read-writecurrent
hpnicfDot11RRM11aSpectrumManag
OBJECT-TYPE
Enable/Disable spectrum management for 802.11a radios. When spectrum management is enabled, the WLAN sub-system advertises power capabilities of the AP and power constraints applicable to all devices in the BSS based on regulatory domain specification.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.5TruthValueread-writecurrent
hpnicfDot11RRMAutoChlAvoid11h
OBJECT-TYPE
Configure the auto-channel set as non-dot11h channels, this is, only the non-dot11h channels belonging to the country code are scanned during initial channel selection and one of them is selected.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.6TruthValueread-writecurrent
hpnicfDot11RRMScanChl
OBJECT-TYPE
Set the scan mode. auto: When this option is set, all channels of the country code being set are scanned. all: When this option is set, all the channels of the radio band are scanned.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.7INTEGER {auto(1), all(2)}read-writecurrent
hpnicfDot11RRMScanRptIntvel
OBJECT-TYPE
Set the scan report interval.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.8Integer32 (5..120)read-writecurrent
hpnicfDot11APInterfNumThreshhd
OBJECT-TYPE
Represents threshold of AP interference . If the value of AP interference exceeds this threshold, AP interference trap will be sent. If the value of this node is zero, AP interference trap will be sent immediately.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.9Integer32read-writecurrent
hpnicfDot11StaInterfNumThreshhd
OBJECT-TYPE
Represents threshold of STA interference. If the value of STA interference exceeds this threshold, STA interference trap will be sent. If the value of this node is zero, STA interference trap will be sent immediately.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.10Integer32read-writecurrent
hpnicfDot11RRM11nMultiCastMcs
OBJECT-TYPE
Specify the modulation and coding scheme (MCS) index for 802.11n multicast rates. The value 4294967295 indicates that no MCS index is specified. No MCS index is specified for 802.11n multicast rates by default. Besides 4294967295, the specified MCS index for 802.11n multicast rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. Before configure the MCS index for 802.11n multicast rates, the maximum MCS index for 802.11n mandatory rates must be configured
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.11Unsigned32 (0..76 | 4294967295)read-writecurrent
hpnicfDot11RRM11acMadtMaxNss
OBJECT-TYPE
Specify the maximum NSS index for 802.11ac mandatory rates. The value 0 indicates that no maximum NSS index is specified. No maximum NSS index is specified for 802.11ac mandatory rates by default. The specified maximum NSS index for 802.11ac supported rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.12Integer32 (0..8)read-writecurrent
hpnicfDot11RRM11acSuptMaxNss
OBJECT-TYPE
Specify the maximum NSS index for 802.11ac supported rates. The specified maximum NSS index for 802.11ac supported rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.13Integer32 (1..8)read-writecurrent
hpnicfDot11RRM11acMultiCastNss
OBJECT-TYPE
Specify the NSS index for 802.11ac multicast rates. The value 0 indicates that no NSS index is specified. No NSS index is specified for 802.11ac multicast rates by default. The specified NSS index for 802.11ac multicast rates must be no less than the specified maximum NSS index for 802.11ac mandatory rates. Before configuring the NSS index for 802.11ac multicast rates, the maximum NSS index for 802.11ac mandatory rates must be configured. Besides, it must be configured together with the node below.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.14Integer32 (0..8)read-writecurrent
hpnicfDot11RRM11acMultiCastVhtMcs
OBJECT-TYPE
Specify the MCS index for 802.11ac multicast rates. The value 255 indicates that no MCS index is specified. No MCS index is specified for 802.11ac multicast rates by default. Besides, it must be configured together with the node above.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.1.15Integer32 (0..9 | 255)read-writecurrent
hpnicfDot11RRMRadioCfgTable
OBJECT-TYPE
Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2not-accessiblecurrent
hpnicfDot11RRMRadioCfgEntry
OBJECT-TYPE
Configure WLAN RRM based radio type. When 802.11b parameter is modified, 802.11g parameter will be changed at the same time. In the same way, when 802.11g parameter is modified, 802.11b parameter will be changed at the same time.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1not-accessiblecurrent
hpnicfDot11RRMRadioType
OBJECT-TYPE
802.11 radio type.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.1HpnicfDot11RadioTypenot-accessiblecurrent
hpnicfDot11RRMCfgChlState
OBJECT-TYPE
Enable/Disable dynamic channel selection.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.2TruthValueread-writecurrent
hpnicfDot11RRMCfgChlMode
OBJECT-TYPE
Configure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.3INTEGER {selfDecisive(1), userTriggered(2)}read-writecurrent
hpnicfDot11RRMChlProntoRadioElmt
OBJECT-TYPE
Specify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of channel selection control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.4Unsigned32read-writecurrent
hpnicfDot11RRMCfgPwrState
OBJECT-TYPE
Enable/Disable dynamic power selection for the band.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.5TruthValueread-writecurrent
hpnicfDot11RRMCfgPwrMode
OBJECT-TYPE
Configure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.6INTEGER {selfDecisive(1), userTriggered(2)}read-writecurrent
hpnicfDot11RRMPwrProntoRadioElmt
OBJECT-TYPE
Specify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of transmit power control is user-triggered. When configuring, the higher 24 bits stand for the AP index, and the last 8 bits stand for the radio index. 4294967295 stand for configuring each radio on all APs.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.7Unsigned32read-writecurrent
hpnicfDot11RRMCfgIntrvl
OBJECT-TYPE
Configure the calibration interval.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.8Integer32read-writecurrent
hpnicfDot11RRMCfgIntrfThres
OBJECT-TYPE
Configure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel reaches the set threshold, RRM will perform resource adjustment to control the situation.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.9Integer32 (40..100)read-writecurrent
hpnicfDot11RRMCfgNoiseThres
OBJECT-TYPE
Configure the noise threshold.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.10Integer32 (-127..127)read-writecurrent
hpnicfDot11RRMCfgPERThres
OBJECT-TYPE
Configure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.11Integer32 (1..100)read-writecurrent
hpnicfDot11RRMCfgToleranceFctr
OBJECT-TYPE
Configure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interference and packet error rate than those specified by the user.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.12Integer32 (1..45)read-writecurrent
hpnicfDot11RRMCfgAdjacencyFctr
OBJECT-TYPE
Configure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value n is the adjacency factor.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.2.1.13Integer32 (1..16)read-writecurrent
hpnicfDot11RRMAPCfgTable
OBJECT-TYPE
This table defines the RRM parameters for AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3not-accessiblecurrent
hpnicfDot11RRMAPCfgEntry
OBJECT-TYPE
Each entry contains information of RRM parameters for AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3.1not-accessiblecurrent
hpnicfDot11RRMAPWorkMode
OBJECT-TYPE
AP work mode.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.3.1.1INTEGER {normal(1), monitor(2), hybrid(3)}read-writecurrent
hpnicfDot11RRMSDRadioGroupTable
OBJECT-TYPE
This table defines RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4not-accessiblecurrent
hpnicfDot11RRMSDRadioGroupEntry
OBJECT-TYPE
Each entry contains information of one RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1not-accessiblecurrent
hpnicfDot11RRMSDRadioGroupId
OBJECT-TYPE
Represents RRM self-decisive radio group ID.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.1Unsigned32not-accessiblecurrent
hpnicfDot11RRMSDRadioGroupDesc
OBJECT-TYPE
Represents the description of RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.2OCTET STRINGread-createcurrent
hpnicfDot11RRMSDRdGrpChlHolddownTm
OBJECT-TYPE
Represents the channel holddown time of RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.3Unsigned32read-createcurrent
hpnicfDot11RRMSDRdGrpPwrHolddownTm
OBJECT-TYPE
Represents the power holddown time of RRM self-decisive radio group.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.4Unsigned32read-createcurrent
hpnicfDot11RRMSDRdGroupRowStatus
OBJECT-TYPE
The row status of this table entry.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.4.1.5RowStatusread-createcurrent
hpnicfDot11RRMAPCfg2Table
OBJECT-TYPE
This table defines the RRM parameters for AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5not-accessiblecurrent
hpnicfDot11RRMAPCfg2Entry
OBJECT-TYPE
Each entry contains information of RRM parameters for AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1not-accessiblecurrent
hpnicfDot11RRMAPSerialID
OBJECT-TYPE
Serial ID of the AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.1HpnicfDot11ObjectIDTypenot-accessiblecurrent
hpnicfDot11RRMAPIntfThreshold
OBJECT-TYPE
Represents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.2Integer32read-writecurrent
hpnicfDot11RRMStaIntfThreshold
OBJECT-TYPE
Represents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.3Integer32read-writecurrent
hpnicfDot11RRMCoChlIntfTrapThhd
OBJECT-TYPE
Represents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.4Integer32read-writecurrent
hpnicfDot11RRMAdjChlIntfTrapThhd
OBJECT-TYPE
Represents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.1.5.1.5Integer32read-writecurrent
hpnicfDot11RRMDetectGroup
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2
hpnicfDot11RRMChlRptTable
OBJECT-TYPE
This table shows the RRM channel information of each radio on all APs.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1not-accessiblecurrent
hpnicfDot11RRMChlRptEntry
OBJECT-TYPE
Each entry contains information of RRM channel information of the radio on the AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1not-accessiblecurrent
hpnicfDot11RRMRadioIndex
OBJECT-TYPE
Represents index of the radio.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.1HpnicfDot11RadioElementIndexaccessible-for-notifycurrent
hpnicfDot11RRMChlRptChlNum
OBJECT-TYPE
Channel number.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.2Integer32accessible-for-notifycurrent
hpnicfDot11RRMChlRptChlType
OBJECT-TYPE
Channel type.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.3INTEGER {primeChannel(1), offChannel(2)}read-onlycurrent
hpnicfDot11RRMChlRptChlQlty
OBJECT-TYPE
Channel quality.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.4INTEGER {good(1), bad(2)}read-onlycurrent
hpnicfDot11RRMChlRptNbrCnt
OBJECT-TYPE
Number of neighbors found on the channel.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.5Integer32read-onlycurrent
hpnicfDot11RRMChlRptLoad
OBJECT-TYPE
Load observed on the channel in percentage.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.6Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMChlRptUtlz
OBJECT-TYPE
Utilization of the channel in percentage.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.7Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMChlRptIntrf
OBJECT-TYPE
Interference observed on the channel in percentage.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.8Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMChlRptPER
OBJECT-TYPE
Packet error rate observed on the channel in percentage.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.9Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMChlRptRetryRate
OBJECT-TYPE
Percentage of retransmission happened on the channel.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.10Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMChlRptNoise
OBJECT-TYPE
Noise observed on the channel.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.11Integer32read-onlycurrent
hpnicfDot11RRMChlRptRadarIndtcr
OBJECT-TYPE
Radar detection status.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.1.1.12INTEGER {detected(1), notDetected(2)}read-writecurrent
hpnicfDot11RRMNbrInfoTable
OBJECT-TYPE
This table shows the RRM neighbor information of each radio on all APs.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2not-accessiblecurrent
hpnicfDot11RRMNbrInfoEntry
OBJECT-TYPE
Each entry contains information of RRM neighbor information of the radio on an AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1not-accessiblecurrent
hpnicfDot11RrmNbrBSSID
OBJECT-TYPE
MAC address of the AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.1MacAddressnot-accessiblecurrent
hpnicfDot11RrmNbrChl
OBJECT-TYPE
Channel number on which the neighbor was found.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.2HpnicfDot11ChannelScopeTyperead-onlycurrent
hpnicfDot11RRMNbrIntrf
OBJECT-TYPE
Interference observed on the channel in percentage by neighbor.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.3Integer32 (0..100)read-onlycurrent
hpnicfDot11RrmNbrRSSI
OBJECT-TYPE
Signal strength of the AP in dBm.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.4Integer32read-onlycurrent
hpnicfDot11RrmNbrType
OBJECT-TYPE
Type of the AP, managed or unmanaged.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.5INTEGER {managed(1), unmanaged(2)}read-onlycurrent
hpnicfDot11RrmNbrSSID
OBJECT-TYPE
SSID of the Neighbor.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.2.1.6HpnicfDot11SSIDStringTyperead-onlycurrent
hpnicfDot11RRMHistoryTable
OBJECT-TYPE
This table shows the details of the latest three channel changes and power changes applied on all APs, including time of change, reason of the change and the channel, power, interference parameters.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3not-accessiblecurrent
hpnicfDot11RRMHistoryEntry
OBJECT-TYPE
Each entry shows the details of channel and power changes.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1not-accessiblecurrent
hpnicfDot11RRMHistoryId
OBJECT-TYPE
History number of the change.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.1Integer32not-accessiblecurrent
hpnicfDot11RRMHistoryRecIndctr
OBJECT-TYPE
History record type of the change.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.2INTEGER {before(1), after(2)}not-accessiblecurrent
hpnicfDot11RRMHistoryChl
OBJECT-TYPE
Channel on which the radio operates before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.3HpnicfDot11ChannelScopeTyperead-onlycurrent
hpnicfDot11RRMHistoryPwr
OBJECT-TYPE
Power of the radio before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.4Integer32read-onlycurrent
hpnicfDot11RRMHistoryLoad
OBJECT-TYPE
Load observed on the radio in percentage before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.5Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMHistoryUtlz
OBJECT-TYPE
Utilization of the radio in percentage before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.6Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMHistoryIntrf
OBJECT-TYPE
Interference observed on the radio in percentage before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.7Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMHistoryNoise
OBJECT-TYPE
Noise observed on the radio before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.8Integer32read-onlycurrent
hpnicfDot11RRMHistoryPER
OBJECT-TYPE
Packet error rate observed on the radio in percentage before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.9Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMHistoryRetryRate
OBJECT-TYPE
Percentage of retransmission happened on the radio before/after the change of channel or power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.10Integer32 (0..100)read-onlycurrent
hpnicfDot11RRMHistoryChgReason
OBJECT-TYPE
Reason for the change of channel or power. The various bit positions are: |0 |Others | |1 |Coverage | |2 |Radar | |3 |Retransmission | |4 |Packets discarded | |5 |Interference | 0 is returned when the history record type is after.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.11Bits {others(0), coverage(1), radar(2), retransmission(3), packetsDiscarded(4), interference(5)}read-onlycurrent
hpnicfDot11RRMHistoryChgDateTime
OBJECT-TYPE
The time when the channel or power change occurred.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.3.1.12DateAndTimeread-onlycurrent
hpnicfDot11RRMRadioNbrInfoTable
OBJECT-TYPE
This table shows the RRM neighbor information of each radio on all APs.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4not-accessiblecurrent
hpnicfDot11RRMRadioNbrInfoEntry
OBJECT-TYPE
Each entry contains information of RRM neighbor information of the radio on an AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1not-accessiblecurrent
hpnicfDot11RRMRadioNbrAPID
OBJECT-TYPE
AP serial id.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.1HpnicfDot11ObjectIDTypenot-accessiblecurrent
hpnicfDot11RRMRadioNbrRadioID
OBJECT-TYPE
Radio Id on AP.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.2HpnicfDot11RadioScopeTypenot-accessiblecurrent
hpnicfDot11RRMRadioNbrSSID
OBJECT-TYPE
All neighbour SSIDs scanned by the selected radio.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.2.4.1.3OCTET STRINGread-onlycurrent
hpnicfDot11RRMNotifyGroup
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3
hpnicfDot11RRMChlQltyNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1
hpnicfDot11RRMChlQltyNtfPrefix
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0
hpnicfDot11RRMResChgNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2
hpnicfDot11RRMResChgNtfPrefix
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2.0
hpnicfDot11RRMNotificationsVar
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3
hpnicfDot11NewPower
OBJECT-TYPE
Power of the radio after the change of power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3.1Integer32accessible-for-notifycurrent
hpnicfDot11OldPower
OBJECT-TYPE
Power of the radio before the change of power.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.3.2Integer32accessible-for-notifycurrent
hpnicfDot11MonitorDetectedGroup
OBJECT-IDENTITY
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4
hpnicfDot11MonitorDetectedDevTable
OBJECT-TYPE
This table shows the devices of AP detected
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1not-accessiblecurrent
hpnicfDot11MonitorDetectedDevEntry
OBJECT-TYPE
Each entry contains information of detected devices.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1not-accessiblecurrent
hpnicfDot11MonitorDevMAC
OBJECT-TYPE
Represents MAC address of the device detected.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.1MacAddressnot-accessiblecurrent
hpnicfDot11MonitorDevType
OBJECT-TYPE
Represents type of the device detected.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.2INTEGER {client(1), ap(2), adhoc(3), wirelessBridge(4), unknown(5)}read-onlycurrent
hpnicfDot11MonitorDevVendor
OBJECT-TYPE
Represents vendor of the detected device.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.3OCTET STRINGread-onlycurrent
hpnicfDot11MonitorDevSSID
OBJECT-TYPE
Represents the service set identifier for the ESS of the device which type is ap or adhoc.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.4OCTET STRINGread-onlycurrent
hpnicfDot11MonitorDevBSSID
OBJECT-TYPE
Represents the basic service set identifier of the detected device.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.5MacAddressread-onlycurrent
hpnicfDot11MonitorDevChannel
OBJECT-TYPE
Represents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is interference between adjacent channels.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.6HpnicfDot11ChannelScopeTyperead-onlycurrent
hpnicfDot11MonitorRadioId
OBJECT-TYPE
Represents the radio ID of the AP that detected the device.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.7HpnicfDot11RadioScopeTyperead-onlycurrent
hpnicfDot11MonitorDevMaxRSSI
OBJECT-TYPE
Represents the maximum detected RSSI of the device in a scan report cycle.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.8Integer32read-onlycurrent
hpnicfDot11MonitorDevBeaconIntvl
OBJECT-TYPE
Represents the beacon interval for the detected device(not include the device which type is client).
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.9Integer32read-onlycurrent
hpnicfDot11MonitorDevFstDctTime
OBJECT-TYPE
Represents the time at which the device was first detected.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.10DateAndTimeread-onlycurrent
hpnicfDot11MonitorDevLstDctTime
OBJECT-TYPE
Represents the time at which the device was detected last time.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.11DateAndTimeread-onlycurrent
hpnicfDot11MonitorDevClear
OBJECT-TYPE
This object is used to clear the information of the device detected in the WLAN. It will return false for get operation.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.12TruthValueread-writecurrent
hpnicfDot11MonitorDevSNR
OBJECT-TYPE
Represents the SNR of the device in a scan report cycle.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.4.1.1.13Integer32read-onlycurrent

Notifications

NameOIDStatus
hpnicfDot11RRMIntrfLimit
NOTIFICATION-TYPE
This notification will be sent when interference on the radio exceeds the limit.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.1current
hpnicfDot11RRMPERLimit
NOTIFICATION-TYPE
This notification will be sent when packet error rate on the radio exceeds the limit.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.2current
hpnicfDot11RRMNoiseLimit
NOTIFICATION-TYPE
This notification will be sent when noise on the radio exceeds the limit.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.1.0.3current
hpnicfDot11RRMPowerChange
NOTIFICATION-TYPE
This notification will be sent when power changed on the radio automatically.
1.3.6.1.4.1.11.2.14.11.15.2.75.8.3.2.0.1current