HPN-ICF-DOT11-CFG-MIB
- Registered at
- 1.3.6.1.4.1.11.2.14.11.15.2.75.4
- Last updated
- 2010-09-25 18:00
- Revisions
- 2010-09-25 18:00, 2010-09-02 18:00, 2009-07-29 18:00, 2009-05-07 20:00, 2009-03-20 15:30, 2008-11-07 15:30, 2008-07-09 18:00, 2008-02-25 18:00, 2007-12-21 18:00, 2007-10-09 16:55, 2007-06-19 18:00, 2007-04-27 20:00, 2007-02-01 20:00, 2006-05-10 19:00
- Namespace
- hp
- Source file
HPN-ICF-DOT11-CFG-MIB- Digest
sha256:0acafc42b81f2225eb7f799271f80c40951a3c1bd7bfa736da336a5dbe61746c
Description
This MIB provides information about WLAN configuration. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC. Fit AP Applied in the enterprise environment, it will work under the control and management from AC. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP. Radio The chip set to receive and send wireless signal. Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.) Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association. MSDU MAC Service Data Unit, it is frame format defined by 802.11. TU It is 1,024 microseconds (ms), which is about 1 millisecond. AKM The authentication and key management method defined by 802.11i, and which includes 802.1x and pre-shared key.
Imports
| From | Symbols |
|---|---|
| HPN-ICF-DOT11-REF-MIB | HpnicfDot11AuthenType, HpnicfDot11ChannelScopeType, HpnicfDot11CirMode, HpnicfDot11ObjectIDType, HpnicfDot11PreambleType, HpnicfDot11RadioElementIndex, HpnicfDot11RadioScopeType, HpnicfDot11RadioType, HpnicfDot11RadioType2, HpnicfDot11SSIDEncryptModeType, HpnicfDot11SSIDStringType, HpnicfDot11SecIEStatusType, HpnicfDot11ServicePolicyIDType, HpnicfDot11TruthValueCM, HpnicfDot11TunnelSecSchemType, HpnicfDot11TxPwrLevelScopeType, HpnicfDot11WorkMode, hpnicfDot11, hpnicfDot11APElementIndex |
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddress |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso |
| SNMPv2-TC | DateAndTime, DisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
HPN-ICF-DOT11-CFG-MIB HPN-ICF-DOT11-REF-MIB HPN-ICF-OID-MIB IANAifType-MIB IF-MIB INET-ADDRESS-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| hpnicfDot11GlobeConfigGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1 | |||
| hpnicfDot11GlobalCountryCode OBJECT-TYPE Represents the country code for wireless network. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.1 | OCTET STRING (SIZE(3)) | read-write | current |
| hpnicfDot11StaKeepALiveTimerIntvl OBJECT-TYPE Represents the interval of the keep alive requests sent between AP and STA. Default value 0 : The keep alive function is disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.2 | Unsigned32 | read-write | current |
| hpnicfDot11StaIdleTimerIntvl OBJECT-TYPE Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.3 | Integer32 | read-write | current |
| hpnicfDot11BroadcastProbeReply OBJECT-TYPE Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.4 | TruthValue | read-write | current |
| hpnicfDot11APScanMode OBJECT-TYPE Represents the scanning mode for AP. The following values are supported: active - AP will actively do scan. passive - AP will passively do scan. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.5 | INTEGER {active(1), passive(2)} | read-write | current |
| hpnicfDot11ACCtrlTunnelSecSupport OBJECT-TYPE Represents what security schemes are supported for CAPWAP Control tunnel. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.6 | HpnicfDot11TunnelSecSchemType | read-write | current |
| hpnicfDot11ACDataTunnelSecSupport OBJECT-TYPE Represents what security schemes are supported for CAPWAP data tunnel. The cleartxt is the default scheme. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.7 | HpnicfDot11TunnelSecSchemType | read-write | current |
| hpnicfDot11ACAutoAPSupport OBJECT-TYPE Represents enable the auto AP functionality or not. 'true' : The auto AP functionality is enabled. 'false': The auto AP functionality is disabled | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.8 | TruthValue | read-write | current |
| hpnicfDot11AutoAPName OBJECT-TYPE Represents the name of auto AP that needs to be made persistent. When read the value from the node, NULL value be returned. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.9 | OCTET STRING (SIZE(0..127)) | read-write | current |
| hpnicfDot11PersistentName OBJECT-TYPE Represents the new name of auto AP after being made persistent. When read the value from the node, NULL value be returned. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.10 | OCTET STRING (SIZE(0..127)) | read-write | current |
| hpnicfDot11IntfTrapThreshold OBJECT-TYPE Represents threshold of interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.11 | Integer32 | read-write | current |
| hpnicfDot11MonitorInterval OBJECT-TYPE Represents the monitoring interval. Default value 0 : The monitoring functionality is changed to real-time mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.12 | Unsigned32 (0 | 5..15) | read-write | current |
| hpnicfDot11SampleInterval OBJECT-TYPE Represents the sampling interval. Default value 0 : The sampling functionality is disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.13 | Unsigned32 (0 | 10..300) | read-write | current |
| hpnicfDot11ChnlSwitChkInterval OBJECT-TYPE Represents the checking interval of channel switch. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.14 | Unsigned32 (8..180) | read-write | current |
| hpnicfDot11APUserUplimit OBJECT-TYPE Represents the upper limit of user which has access to this AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.15 | Unsigned32 (0..65535) | read-write | current |
| hpnicfDot11APL2IsolateEnable OBJECT-TYPE Represents enable the layer2 isolation or not. 'true' : The layer2 isolation functionality is enabled. 'false': The layer2 isolation functionality is disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.16 | TruthValue | read-write | current |
| hpnicfDot11APBSSIDSupportNum OBJECT-TYPE Represents the max number of BSSID supported by Current AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.17 | Integer32 | read-only | current |
| hpnicfDot11APLastUpdateStatTime OBJECT-TYPE Represents date and time update statistic information lately. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.18 | DateAndTime | read-only | current |
| hpnicfDot11APDoSProtectEnable OBJECT-TYPE Represents enable the DOS protection or not. 'true' : The DOS protection functionality is enabled. 'false': The DOS protection functionality is disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.19 | TruthValue | read-write | current |
| hpnicfDot11MaxAPPerIf OBJECT-TYPE Represents max AP number that can be connected to AC interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.20 | Unsigned32 (0..65535) | read-write | current |
| hpnicfDot11SampleTimeStamp OBJECT-TYPE Represents the start time of current sample period. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.21 | DateAndTime | read-only | current |
| hpnicfDot11UplinkTrackId OBJECT-TYPE Represents the track id of AP. Default value 0 : The uplink track function for AP is disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.22 | Unsigned32 | read-write | current |
| hpnicfDot11RtCollectSwitch OBJECT-TYPE This object is used to turn on/off real-time statistics collection between AC and AP. If the value is true, hpnicfDot11RtCollectIntvl will take effect. Otherwise, hpnicfDot11RglCollectIntvl will take effect. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.23 | TruthValue | read-write | current |
| hpnicfDot11RglCollectIntvl OBJECT-TYPE This object represents interval to regularly collect statistics from AC to AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.24 | Integer32 | read-write | current |
| hpnicfDot11RtCollectIntvl OBJECT-TYPE This object represents interval to collect real-time statistics from AC to AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.25 | Integer32 | read-write | current |
| hpnicfDot11AllAPCpuUsageThreshold OBJECT-TYPE The CPU usage threshold for all AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.26 | Integer32 (0..100) | read-write | current |
| hpnicfDot11AllAPMemUsageThreshold OBJECT-TYPE The memory usage threshold for all AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.27 | Integer32 (0..100) | read-write | current |
| hpnicfDot11AdjIntfTrapThreshold OBJECT-TYPE Represents threshold of adjacent interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.28 | Integer32 | read-write | current |
| hpnicfDot11AllAPMonitorMode OBJECT-TYPE Represents what work mode for All AP. The following values are supported: normal, - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.29 | INTEGER {normal(1), monitor(2), hybrid(3)} | read-write | current |
| hpnicfDot11GlobalApFmwUpdState OBJECT-TYPE Represents the status of version auto-update for an AP. The following values are supported: enable - AP version will be updated automatically. disable - AP version will not be updated automatically. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.30 | INTEGER {enable(1), disable(2)} | read-write | current |
| hpnicfDot11ACNasIDCM OBJECT-TYPE Represents the NAS-ID of current AC. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.1.31 | OCTET STRING | read-write | current |
| hpnicfDot11PolicyConfigGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2 | |||
| hpnicfDot11RadioPolicyTable OBJECT-TYPE The table defines the parameters for radio policy, as per radio policy of CLI. One radio policy could be assigned to the different radios (AP). | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1 | not-accessible | current | |
| hpnicfDot11RadioPolicyEntry OBJECT-TYPE Each entry contains information of each radio policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1 | not-accessible | current | |
| hpnicfDot11RadioPolicyName OBJECT-TYPE Represents the name of radio policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.1 | OCTET STRING (SIZE(0..127)) | not-accessible | current |
| hpnicfDot11BeaconInterval OBJECT-TYPE Represents the interval for Beacon management frame. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.2 | Integer32 | read-create | current |
| hpnicfDot11DtimInterval OBJECT-TYPE Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.3 | Integer32 | read-create | current |
| hpnicfDot11RtsThreshold OBJECT-TYPE Represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.4 | Integer32 | read-create | current |
| hpnicfDot11FragThreshold OBJECT-TYPE Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.5 | Integer32 | read-create | current |
| hpnicfDot11ShortRetryThreshold OBJECT-TYPE Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RTSThreshold, which shall be made before a failure condition is indicated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.6 | Integer32 | read-create | current |
| hpnicfDot11LongRetryThreshold OBJECT-TYPE Represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RTSThreshold, that shall be made before a failure condition is indicated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.7 | Integer32 | read-create | current |
| hpnicfDot11MaxRxLifetime OBJECT-TYPE Represents the elapsed time. After the time specified by hpnicfDot11MaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.8 | Unsigned32 | read-create | current |
| hpnicfDot11RdoPolicyRowStatus OBJECT-TYPE The status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.9 | RowStatus | read-create | current |
| hpnicfDot11RdoClientMaxCount OBJECT-TYPE Represent the maximum number of stations supported by this radio policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.10 | Integer32 (0..2147483647) | read-create | current |
| hpnicfDot11BeaconIntervalMs OBJECT-TYPE Represents the interval for Beacon management frame. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.1.1.11 | Integer32 | read-create | current |
| hpnicfDot11ServicePolicyTable OBJECT-TYPE The table defines the parameters for ESS, as per service policy of CLI. One service policy could be assigned to the different radios (AP). | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2 | not-accessible | current | |
| hpnicfDot11ServicePolicyEntry OBJECT-TYPE Each entry contains information of each service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1 | not-accessible | current | |
| hpnicfDot11ServicePolicyID OBJECT-TYPE Represents the ID of each service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.1 | HpnicfDot11ServicePolicyIDType | not-accessible | current |
| hpnicfDot11SSIDName OBJECT-TYPE Represents the ESS. As per CLI, the value of service policy name will be SSID. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.2 | HpnicfDot11SSIDStringType | read-create | current |
| hpnicfDot11SSIDHidden OBJECT-TYPE This attribute controls whether the SSID will be advertised in the beacon frame. If it is true, then SSID will not be advertised in the beacon frame. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.3 | TruthValue | read-create | current |
| hpnicfDot11AuthenMode OBJECT-TYPE Represents the Authentication mode defined by 802.11. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.4 | HpnicfDot11AuthenType | read-create | current |
| hpnicfDot11SSIDEncryptionMode OBJECT-TYPE Represents the encryption mode for this ESS. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.5 | HpnicfDot11SSIDEncryptModeType | read-create | current |
| hpnicfDot11WlanInfBindingType OBJECT-TYPE Represents the service policy will bind to what kind of data forwarding interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.6 | OCTET STRING | read-create | current |
| hpnicfDot11WlanInfBindingID OBJECT-TYPE Represents the interface ID of the interface that ESS will bind to. If the value is set to -1, the binding will be removed. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.7 | Integer32 | read-create | current |
| hpnicfDot11SrvPolicyRowStatus OBJECT-TYPE The status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.8 | RowStatus | read-create | current |
| hpnicfDot11ClientMaxCount OBJECT-TYPE Represent the maximum number of stations supported by this service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.9 | Integer32 (0..2147483647) | read-create | current |
| hpnicfDot11SPInCirMode OBJECT-TYPE CIR(committed information rate) mode of inbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.10 | HpnicfDot11CirMode | read-create | current |
| hpnicfDot11SPInCirValue OBJECT-TYPE Represents the CIR of inbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.11 | Integer32 | read-create | current |
| hpnicfDot11SPOutCirMode OBJECT-TYPE CIR(committed information rate) mode of outbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.12 | HpnicfDot11CirMode | read-create | current |
| hpnicfDot11SPOutCirValue OBJECT-TYPE Represents the CIR of outbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.13 | Integer32 | read-create | current |
| hpnicfDot11WlanInfPVID OBJECT-TYPE Represents the VLAN ID of SSID. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.14 | Integer32 | read-create | current |
| hpnicfDot11SPInCirStaticValue OBJECT-TYPE Represents the CIR of inbound direction for static CIR mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.15 | Integer32 | read-create | current |
| hpnicfDot11SPOutCirStaticValue OBJECT-TYPE Represents the CIR of outbound direction for static CIR mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.16 | Integer32 | read-create | current |
| hpnicfDot11SPIsolate OBJECT-TYPE If it is true, then stations connected with the service policy are isolated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.17 | TruthValue | read-create | current |
| hpnicfDot11WlanexAuthServerIP OBJECT-TYPE Represents the IP address of the Wlanex Authentication server | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.18 | IpAddress | read-create | current |
| hpnicfDot11SPBeaconMeasEnable OBJECT-TYPE If it is true, then beacon-measurement is enabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.19 | TruthValue | read-create | current |
| hpnicfDot11SPBeaconMeasType OBJECT-TYPE Represents what the work mode for BeaconMeasurement type. The following values are supported: passive, - BeaconMeasurement will use the passive type. active - BeaconMeasurement will use the active type. beaconTable - BeaconMeasurement will use the beacon table type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.20 | INTEGER {passive(1), active(2), beaconTable(3)} | read-create | current |
| hpnicfDot11SPBeaconMeasInterval OBJECT-TYPE Represents the beacon-measurement interval. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.21 | Integer32 (10..200) | read-create | current |
| hpnicfDot11AuthenModeCM OBJECT-TYPE Represents the Authentication mode defined by 802.11. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.22 | INTEGER {opensystem(0), sharedkey(1)} | read-create | current |
| hpnicfDot11SecIEStatusCM OBJECT-TYPE To enable the security Information element in the beacon and probe response frames sent by AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.23 | INTEGER {none(0), wpa(1), wpa2(2), wlanex(3)} | read-create | current |
| hpnicfDot11SecurityCiphersCM OBJECT-TYPE The WLAN system support the following cipher type for data frame encryption. none wep40 wep104 tkip aesccmp wpi-SMS4 When the value of node equals to zero, it means no configuration or undo operation. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.24 | INTEGER {none(0), wep40(1), wep104(2), tkip(3), aesccmp(4), wpisms4(5)} | read-create | current |
| hpnicfDot11SrvPolicyStatusCM OBJECT-TYPE The status of the Service Policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.25 | INTEGER {off(0), on(1)} | read-create | current |
| hpnicfDot11SSIDHiddenCM OBJECT-TYPE This attribute controls whether the SSID will be advertised in beacon frames. If it is dot11true, the SSID will not be advertised in beacon frames. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.26 | HpnicfDot11TruthValueCM | read-create | current |
| hpnicfDot11SPIsolateCM OBJECT-TYPE If it is dot11true, the clients connected with the service policy are isolated to each other. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.2.1.27 | HpnicfDot11TruthValueCM | read-create | current |
| hpnicfDot11ServicePolicyExtTable OBJECT-TYPE The table defines the parameters for ESS, as per service policy of CLI. When the value of hpnicfDot11SSIDEncryptionMode equals to cipher(2), more configuration for a ESS will be put into the table. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3 | not-accessible | current | |
| hpnicfDot11ServicePolicyExtEntry OBJECT-TYPE Each entry contains information of each service policy under cipher(2) mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1 | not-accessible | current | |
| hpnicfDot11ServicePolicyExtID OBJECT-TYPE Represents the ID of each service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.1 | HpnicfDot11ServicePolicyIDType | not-accessible | current |
| hpnicfDot11SecIEStatus OBJECT-TYPE To enable the security Information element in the beacon and probe response frames sent by AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.2 | HpnicfDot11SecIEStatusType | read-create | current |
| hpnicfDot11SecurityCiphers OBJECT-TYPE The WLAN system support the following cipher type for data frame encryption. wep40(2) tkip(4) aesccmp(16) wep104(32) wpisms4(64) wep128(128) For each service policy, it could support multiple cipher types at the same time. So the value of object could combine multiple value of cipher type above. When the value of node equals to zero, it means no configuration or undo operation. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.3 | Integer32 | read-create | current |
| hpnicfDot11CipherKeyIndex OBJECT-TYPE Represents the key index of cipher key for packet. When hpnicfDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.4 | Integer32 | read-create | current |
| hpnicfDot11CipherKey OBJECT-TYPE Represents the cipher key for packet. When hpnicfDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.5 | OCTET STRING | read-create | current |
| hpnicfDot11SrvPolicyExtRowStatus OBJECT-TYPE The status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.6 | RowStatus | read-create | current |
| hpnicfDot11CipherKeyType OBJECT-TYPE Represents the cipher key type of hpnicfDot11CipherKey. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.3.1.7 | INTEGER {char(1), hex(2)} | read-create | current |
| hpnicfDot11RadioPolicyExtTable OBJECT-TYPE The table defines the radio policy of each radio. It can't be modified if the radio policy is a default radio policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4 | not-accessible | current | |
| hpnicfDot11RadioPolicyExtEntry OBJECT-TYPE Each entry contains information of each radio policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1 | not-accessible | current | |
| hpnicfDot11RPAPSerialID OBJECT-TYPE This object represents the Serial ID of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.1 | OCTET STRING (SIZE(0..127)) | not-accessible | current |
| hpnicfDot11RPRadioID OBJECT-TYPE This object represents each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.2 | HpnicfDot11RadioScopeType | not-accessible | current |
| hpnicfDot11RPBeaconInterval OBJECT-TYPE This object represents the interval for Beacon management frame. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.3 | Integer32 | read-write | current |
| hpnicfDot11RPDtimInterval OBJECT-TYPE This object represents the number of beacon intervals that shall elapse between transmissions of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.4 | Integer32 | read-write | current |
| hpnicfDot11RPRtsThreshold OBJECT-TYPE This object represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.5 | Integer32 | read-write | current |
| hpnicfDot11RPFragThreshold OBJECT-TYPE This object represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.6 | Integer32 | read-write | current |
| hpnicfDot11RPShortRetryThreshold OBJECT-TYPE This object represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RTSThreshold, that shall be made before a failure condition is indicated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.7 | Integer32 | read-write | current |
| hpnicfDot11RPLongRetryThreshold OBJECT-TYPE This object represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RTSThreshold, and that shall be made before a failure condition is indicated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.8 | Integer32 | read-write | current |
| hpnicfDot11RPClientMaxCount OBJECT-TYPE This object represents the maximum number of stations supported by this radio policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.9 | Integer32 (0..2147483647) | read-write | current |
| hpnicfDot11RPBeaconIntervalCM OBJECT-TYPE This object represents beacon interval. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.4.1.10 | Integer32 | read-write | current |
| hpnicfDot11SrvPortSecurityTable OBJECT-TYPE This table defines the WLAN security status for ESS, BSS and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, hpnicfPortSecurityTables should be used to configure port security. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5 | not-accessible | current | |
| hpnicfDot11SrvPortSecurityEntry OBJECT-TYPE There is a row in this table for service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1 | not-accessible | current | |
| hpnicfDot11SecurityServicePolicyID OBJECT-TYPE Represents the ID of each service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.1 | HpnicfDot11ServicePolicyIDType | not-accessible | current |
| hpnicfDot11SrvPortSecurityMode OBJECT-TYPE Determines the security modes of the WLAN port. noRestrictions The default value, no any security mode is set. userLoginSecureExt Access to the port is denied until the port client is authorized (by 802.1X). psk Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext Access to the port is denied until the port client is authenticated (by ext). | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.2 | INTEGER {noRestrictions(1), userLoginSecureExt(2), psk(3), macAddressAndPsk(4), userLoginSecureExtOrPsk(5), ext(6)} | read-write | current |
| hpnicfDot11SrvSecurityKeyType OBJECT-TYPE This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone - This means the key type is not set yet. userLoginTxKeyTypeDot11Key - This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4 session encryption. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.3 | INTEGER {userLoginTxKeyTypeNone(1), userLoginTxKeyTypeDot11Key(2), userLoginTxKeyTypeRsaRC4Key(3)} | read-write | current |
| hpnicfDot11SrvSecurityPskKeyMode OBJECT-TYPE This is the password input mode. When input as pskKeyModePassPhrase, hpnicfDot11SrvSecurityPskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, hpnicfDot11SrvSecurityPskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.4 | INTEGER {pskKeyModeNone(1), pskKeyModePassPhrase(2), pskKeyModeRawKey(3)} | read-write | current |
| hpnicfDot11SrvSecurityPskKeyString OBJECT-TYPE This is the password string used for psk authentication. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.5 | DisplayString (SIZE(0..64)) | read-write | current |
| hpnicfDot11SrvPortSecurityModeCM OBJECT-TYPE Determines the security modes of the WLAN port. none - The default value, no any security mode is set. psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). radius - Access to the port is denied until the port client is authorized (by 802.1X). wlanex - Access to the port is denied until the port client is authenticated by wlan cert. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.5.1.6 | INTEGER {none(0), psk(1), radius(2), wlanex(3)} | read-write | current |
| hpnicfDot11SrvPolicyExtendTable OBJECT-TYPE The table defines the parameters of each service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6 | not-accessible | current | |
| hpnicfDot11SrvPolicyExtendEntry OBJECT-TYPE Each entry contains information of each service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6.1 | not-accessible | current | |
| hpnicfDot11SPEnable OBJECT-TYPE Represents whether the service policy is enabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.2.6.1.1 | INTEGER {enable(1), disable(2)} | read-write | current |
| hpnicfDot11APConfigGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3 | |||
| hpnicfDot11APTemplateTable OBJECT-TYPE By AP template CLI, administrator will configure the parameters of AP by convenience. Before AP boot up and connect to AC by CAPWAP tunnel, administrator will create AP template for each AP. When AP connect to AC, AC will assign configuration to AP by hpnicfDot11APSerialID information in AP template. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1 | not-accessible | current | |
| hpnicfDot11APTemplateEntry OBJECT-TYPE Each entry contains configuration information for each AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1 | not-accessible | current | |
| hpnicfDot11APTemplateName OBJECT-TYPE Represents the name of AP template. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.1 | OCTET STRING (SIZE(0..127)) | not-accessible | current |
| hpnicfDot11APSerialID OBJECT-TYPE Represents AP serial id. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.2 | OCTET STRING | read-create | current |
| hpnicfDot11TemplateAPModelAlias OBJECT-TYPE Represents the alias of AP model name. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.3 | OCTET STRING | read-create | current |
| hpnicfDot11Description OBJECT-TYPE This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.4 | OCTET STRING | read-create | current |
| hpnicfDot11APWorkMode OBJECT-TYPE Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.5 | INTEGER {normal(1), monitor(2), hybrid(3)} | read-create | current |
| hpnicfDot11APTemplateRowStatus OBJECT-TYPE The status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.6 | RowStatus | read-create | current |
| hpnicfDot11APName OBJECT-TYPE Represents the AP name. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.7 | OCTET STRING | read-create | current |
| hpnicfDot11StatisInterv OBJECT-TYPE Represents the interval of radio statistic. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.8 | Integer32 | read-create | current |
| hpnicfDot11APBroadcastProbeReply OBJECT-TYPE Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.9 | TruthValue | read-create | current |
| hpnicfDot11StaIdleTimerInterv OBJECT-TYPE Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.10 | Integer32 | read-create | current |
| hpnicfDot11StaKeepAliveTimerInterv OBJECT-TYPE Represents the interval of the keep alive requests sent between AP and STA. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.11 | Integer32 | read-create | current |
| hpnicfDot11APCir OBJECT-TYPE Represents the committed information rate between AP and AC. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.12 | Integer32 | read-create | current |
| hpnicfDot11APCbs OBJECT-TYPE Represents the committed burst size between AP and AC. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.13 | Integer32 | read-create | current |
| hpnicfDot11APPriorityLevel OBJECT-TYPE This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.14 | Integer32 (0..7) | read-create | current |
| hpnicfDot11APElementID OBJECT-TYPE This object represents the AP element ID. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.15 | Integer32 | read-only | current |
| hpnicfDot11APDevDetectEnable OBJECT-TYPE Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object hpnicfDot11APWorkMode is monitor, device detection can not be enabled with object hpnicfDot11APDevDetectEnable. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.16 | TruthValue | read-create | current |
| hpnicfDot11APGetIPMethod OBJECT-TYPE This object represents the method how AP gets IP address. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.17 | INTEGER {dhcpAlloc(1), static(2)} | read-create | current |
| hpnicfDot11StatisIntervMode OBJECT-TYPE This object represents the mode of statics interval. normal - statics interval value between 10s to 120s realtime - statics interval value between 2s to 5s | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.18 | INTEGER {normal(1), realtime(2)} | read-create | current |
| hpnicfDot11ApTrapEnabled OBJECT-TYPE Represents whether the trap status is enabled or not. 'true' : Enable the trap status; 'false' : Disable the trap status. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.19 | TruthValue | read-write | current |
| hpnicfDot11ApFmwUpdState OBJECT-TYPE Represents the status of version auto-update for an AP. The following values are supported: enable - AP version will be updated automatically. disable - AP version will not be updated automatically. inherit - The status will inherit value from apgroup-view or system-view. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.20 | INTEGER {enable(1), disable(2), inherit(3)} | read-create | current |
| hpnicfDot11StatisIntervModeCM OBJECT-TYPE This object represents the mode of statistic interval. off - statistic interval value between 10s to 120s on - statistic interval value between 2s to 5s | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.21 | INTEGER {off(0), on(1)} | read-create | current |
| hpnicfDot11ApNasIDCM OBJECT-TYPE Represents the NAS-ID of current service policy for each specific radio of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.1.1.22 | OCTET STRING | read-create | current |
| hpnicfDot11RadioToConfigTable OBJECT-TYPE Before AP connects to AC, administrator will configure radio parameter to each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2 | not-accessible | current | |
| hpnicfDot11RadioToConfigEntry OBJECT-TYPE Each entry contains configuration information for each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1 | not-accessible | current | |
| hpnicfDot11APTemplateNameCfg OBJECT-TYPE Represents the name of AP template. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.1 | OCTET STRING (SIZE(0..127)) | not-accessible | current |
| hpnicfDot11CfgRadioID OBJECT-TYPE Represents each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.2 | HpnicfDot11RadioScopeType | not-accessible | current |
| hpnicfDot11CfgRadioPolicyName OBJECT-TYPE Represents the name of radio policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.3 | OCTET STRING | read-write | current |
| hpnicfDot11CfgRadioType OBJECT-TYPE Represents the radio will work with which 802.11 radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.4 | HpnicfDot11RadioType | read-write | current |
| hpnicfDot11CfgChannel OBJECT-TYPE Represents the channel allocation of radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.5 | HpnicfDot11ChannelScopeType | read-write | current |
| hpnicfDot11CfgMaxTxPowerLevel OBJECT-TYPE Represents the maximal transmit power scope for AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.6 | HpnicfDot11TxPwrLevelScopeType | read-write | current |
| hpnicfDot11PreambleLen OBJECT-TYPE Represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLen will be valid. Otherwise, the value for it will be invalid. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.7 | HpnicfDot11PreambleType | read-write | current |
| hpnicfDot11CfgRadioStatus OBJECT-TYPE Represents the radio admin status whether is enabled or disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.8 | TruthValue | read-write | current |
| hpnicfDot11CfgRdElementID OBJECT-TYPE Represents the element ID of this radio. It comprises two parts. The highest 24 bits are AP element ID and the lowest 8 bits are radio ID. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.9 | Unsigned32 | read-only | current |
| hpnicfDot11CfgWorkMode OBJECT-TYPE Represents work mode of the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.10 | HpnicfDot11WorkMode | read-write | current |
| hpnicfDot11CfgPwrAttValue OBJECT-TYPE Represents the value of power attenuation. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.11 | Integer32 | read-write | current |
| hpnicfDot11RadioTxArithmetic OBJECT-TYPE Represents the transmission arithmetic of the radio. The following values are supported: quality - Consider the quality first during the transmission. bandwidth - Consider the bandwidth first during the transmission. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.12 | INTEGER {quality(1), bandwidth(2)} | read-write | current |
| hpnicfDot11CfgChannelLockStat OBJECT-TYPE Represents locked status of channel on the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.13 | INTEGER {unlocked(1), locked(2)} | read-write | current |
| hpnicfDot11CfgPowerLockStat OBJECT-TYPE Represents locked status of power on the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.14 | INTEGER {unlocked(1), locked(2)} | read-write | current |
| hpnicfDot11CfgLBRdGroupId OBJECT-TYPE Represents the load balance group ID allocated for the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.15 | Unsigned32 | read-write | current |
| hpnicfDot11CfgRRMSDRdGroupId OBJECT-TYPE Represents the RRM self-decisive group ID allocated for the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.16 | Unsigned32 | read-write | current |
| hpnicfDot11CfgRadioType2 OBJECT-TYPE Represents the radio will work with which 802.11 radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.17 | HpnicfDot11RadioType2 | read-write | current |
| hpnicfDot11CfgIDSEnable OBJECT-TYPE Represents whether intrusion detection is enabled for this radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.18 | TruthValue | read-write | current |
| hpnicfDot11CfgSaEnable OBJECT-TYPE Represents whether spectrum analysis is enabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.19 | TruthValue | read-write | current |
| hpnicfDot11CfgSaCltRtFFTData OBJECT-TYPE Represents whether to collect real-time FFT data for this radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.20 | TruthValue | read-write | current |
| hpnicfDot11CfgSaBand OBJECT-TYPE Represents which band of channels will be monitored when collection real-time FFT data is enabled for this radio. Detection of interference devices and air quality will also be affected. Each band responds to the following channels. dot11g (Channels 1-14) dot11aLower (channels 36-64) dot11aMiddle (channels 100-140) dot11aUpper (channels 149-165). | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.2.1.21 | INTEGER {dot11g(1), dot11aLower(2), dot11aMiddle(3), dot11aUpper(4)} | read-write | current |
| hpnicfDot11APServiceSetTable OBJECT-TYPE For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3 | not-accessible | current | |
| hpnicfDot11APServiceSetEntry OBJECT-TYPE Each entry contains service policy information for each specific radio of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1 | not-accessible | current | |
| hpnicfDot11CfgServicePolicyID OBJECT-TYPE Represents the ID of each service policy used by the AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.1 | HpnicfDot11ServicePolicyIDType | not-accessible | current |
| hpnicfDot11SrvSetRowStatus OBJECT-TYPE The status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.2 | RowStatus | read-create | current |
| hpnicfDot11ServiceSetVlanId OBJECT-TYPE Represents the Vlan ID of BSS which is generated when service policy is binded with the Radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.3.1.3 | Integer32 (0..4094) | read-create | current |
| hpnicfDot11APSysInfoSetTable OBJECT-TYPE The table of the system information for each AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4 | not-accessible | current | |
| hpnicfDot11APSysInfoSetEntry OBJECT-TYPE The system information configuration for each AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1 | not-accessible | current | |
| hpnicfDot11APSysNetID OBJECT-TYPE Represents the system Net ID for AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.1 | OCTET STRING (SIZE(0..127)) | read-write | current |
| hpnicfDot11APCpuUsageThreshold OBJECT-TYPE The CPU usage threshold for AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.2 | Integer32 (0..100) | read-write | current |
| hpnicfDot11APMemUsageThreshold OBJECT-TYPE The memory usage threshold for AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.4.1.3 | Integer32 (0..100) | read-write | current |
| hpnicfDot11APLimitTable OBJECT-TYPE For each connected APs, administrator could configure a series of limits. This table describes the limit information for AP(s). | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5 | not-accessible | current | |
| hpnicfDot11APLimitEntry OBJECT-TYPE Each entry contains the limit information for each AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1 | not-accessible | current | |
| hpnicfDot11APSsidNumLimit OBJECT-TYPE Represents the upper limit of service template binded with this AP. All radios of AP share this limit. Default value 0 : There is no upper limit of service template binded with this AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.1 | Integer32 (0..65535) | read-write | current |
| hpnicfDot11APUserCntLimit OBJECT-TYPE Represents the upper limit of user which has access to this AP. All BSSs binded with AP share this limit. Default value 0 : There is no upper limit of user which has access to this AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.2 | Integer32 (0..65535) | read-write | current |
| hpnicfDot11APUserThreshold OBJECT-TYPE Represents the threshold of user which has access to this AP. All BSSs binded with AP share this limit. If the user counter is overflow, the trap will be sent. Default value 0 : There is no threshold of user which has access to this AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.5.1.3 | Integer32 (0..65535) | read-write | current |
| hpnicfDot11APIfSetTable OBJECT-TYPE The table of the interface information for each AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6 | not-accessible | current | |
| hpnicfDot11APIfSetEntry OBJECT-TYPE The interface information configuration for each AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1 | not-accessible | current | |
| hpnicfDot11APSetIfIndex OBJECT-TYPE Represents the index for a interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1.1 | Integer32 | not-accessible | current |
| hpnicfDot11APIfAlias OBJECT-TYPE This object is an 'alias' name for the interface as specified by a network manager for AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.6.1.2 | DisplayString | read-write | current |
| hpnicfDot11APServiceVlanTable OBJECT-TYPE For all the radios on the AP, it could configure multiple service policies. The table describes the relationship between AP and service policies. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7 | not-accessible | current | |
| hpnicfDot11APServiceVlanEntry OBJECT-TYPE Each entry contains service policy information for each AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1 | not-accessible | current | |
| hpnicfDot11APServiceVlanSerialID OBJECT-TYPE This object represents AP serial id. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.1 | OCTET STRING | not-accessible | current |
| hpnicfDot11APServiceVlanSPID OBJECT-TYPE This object represents the ID of each service policy used by the AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.2 | HpnicfDot11ServicePolicyIDType | not-accessible | current |
| hpnicfDot11APServiceVlanId OBJECT-TYPE This object represents the VLAN ID of BSS which is generated when the service policy is bound to the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.3 | Integer32 (0..4094) | read-create | current |
| hpnicfDot11APServiceVlanRowStatus OBJECT-TYPE This object represents the status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.7.1.4 | RowStatus | read-create | current |
| hpnicfDot11RadioConfigTable OBJECT-TYPE Before AP connects to AC, administrator will configure radio parameter to each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8 | not-accessible | current | |
| hpnicfDot11RadioConfigEntry OBJECT-TYPE Each entry contains configuration information for each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1 | not-accessible | current | |
| hpnicfDot11RCAPSerialID OBJECT-TYPE This object represents the Serial ID of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.1 | OCTET STRING (SIZE(0..127)) | not-accessible | current |
| hpnicfDot11RCRadioID OBJECT-TYPE This object represents each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.2 | HpnicfDot11RadioScopeType | not-accessible | current |
| hpnicfDot11RCRadioType OBJECT-TYPE This object represents the radio will work with which 802.11 radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.3 | HpnicfDot11RadioType | read-write | current |
| hpnicfDot11RCChannel OBJECT-TYPE This object represents the channel allocation of radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.4 | HpnicfDot11ChannelScopeType | read-write | current |
| hpnicfDot11RCPreambleLen OBJECT-TYPE This object represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLen will be valid. Otherwise, the value for it will be invalid. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.5 | HpnicfDot11PreambleType | read-write | current |
| hpnicfDot11RCPwrAttValue OBJECT-TYPE This object represents the value of power attenuation. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.6 | Integer32 | read-write | current |
| hpnicfDot11RCApPowerLevel OBJECT-TYPE Represents the maximal transmit power scope for AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.7 | HpnicfDot11TxPwrLevelScopeType | read-write | current |
| hpnicfDot11RCDynamicChlState OBJECT-TYPE Enable/Disable dynamic channel selection. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.8 | TruthValue | read-write | current |
| hpnicfDot11RCDynamicPowerState OBJECT-TYPE Enable/Disable dynamic power selection for the band. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.9 | TruthValue | read-write | current |
| hpnicfDot11RCRadioStatus OBJECT-TYPE Represents the radio admin status whether is enabled or disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.10 | TruthValue | read-write | current |
| hpnicfDot11RCRadioRate OBJECT-TYPE Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format can be MCS X. The data transmit rates between AP and STA must fall into the configured rates. (Note: For 802.11n radios, the first value will be treated as a mandatory rate, and the second value will be treated as a supported rate. If you configure more than two rates, the configuration cannot take effect. If you configure only one rate, it is considered as the mandatory rate by default.) | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.11 | OCTET STRING (SIZE(0..255)) | read-write | current |
| hpnicfDot11RCPwrAdjustStepLength OBJECT-TYPE Power adjustment step-length in dBm. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.12 | Integer32 | read-only | current |
| hpnicfDot11RCRadioType2 OBJECT-TYPE This object represents the radio will work with which 802.11 radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.13 | HpnicfDot11RadioType2 | read-write | current |
| hpnicfDot11RCPreambleLenCM OBJECT-TYPE This object represents whether use long or short preamble for 802.11 MAC frame. When hpnicfDot11CfgRadioType is either dot11b or dot11g, then value for hpnicfDot11PreambleLenCM will be valid. Otherwise, the value for it will be invalid. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.14 | INTEGER {long(0), short(1)} | read-write | current |
| hpnicfDot11RCDynamicChlStateCM OBJECT-TYPE Enable/Disable dynamic channel selection. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.15 | INTEGER {off(0), on(1)} | read-write | current |
| hpnicfDot11RCRadioStatusCM OBJECT-TYPE Represents the radio admin status whether is enabled or disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.16 | INTEGER {up(1), down(2), testing(3)} | read-write | current |
| hpnicfDot11RCRadioRateCM OBJECT-TYPE Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format of each value can be MCS X. The data transmit rates between AP and client should be one of the configured rates. (Note: For 802.11n radios, the first value is mandatory rate, and the second value is supported rate. If more than two rate values are configured, the configuration will not take effect. If only one rate value is configured, the mandatory rate will be set to the default value.) | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.17 | OCTET STRING (SIZE(0..255)) | read-write | current |
| hpnicfDot11RCDynamicPowerStateCM OBJECT-TYPE Enable/disable dynamic power selection for the band. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.8.1.18 | HpnicfDot11TruthValueCM | read-write | current |
| hpnicfDot11RadioSSIDCfgTable OBJECT-TYPE For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9 | not-accessible | current | |
| hpnicfDot11RadioSSIDCfgEntry OBJECT-TYPE Each entry contains SSID configuration information for each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1 | not-accessible | current | |
| hpnicfDot11RadioSSIDSerialID OBJECT-TYPE This object represents the serial ID of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.1 | HpnicfDot11ObjectIDType | not-accessible | current |
| hpnicfDot11RadioSSIDRadioID OBJECT-TYPE This object represents each radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.2 | HpnicfDot11RadioScopeType | not-accessible | current |
| hpnicfDot11RadioSSIDWLANID OBJECT-TYPE This object represents the WLAN ID of the BSSID. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.3 | Integer32 | not-accessible | current |
| hpnicfDot11RadioSSIDIndex OBJECT-TYPE This object represents the ID of each service policy used by the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.4 | HpnicfDot11ServicePolicyIDType | read-create | current |
| hpnicfDot11RadioBSSID OBJECT-TYPE As MAC address format, it is used to identify BSS. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.5 | MacAddress | read-only | current |
| hpnicfDot11RadioSSIDRowStatus OBJECT-TYPE RowStatus. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.9.1.6 | RowStatus | read-create | current |
| hpnicfDot11APSerialIDTable OBJECT-TYPE The table will provide the general information about APs. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10 | not-accessible | current | |
| hpnicfDot11APSerialIDEntry OBJECT-TYPE Each entry contains the general information of an AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1 | not-accessible | current | |
| hpnicfDot11SIDAPSerialID OBJECT-TYPE Represents AP serial id. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.1 | OCTET STRING | not-accessible | current |
| hpnicfDot11SIDAPWorkMode OBJECT-TYPE Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.2 | INTEGER {normal(1), monitor(2), hybrid(3)} | read-create | current |
| hpnicfDot11SIDAPGetIPMethod OBJECT-TYPE This object represents the method how AP gets IP address. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.3 | INTEGER {dhcpAlloc(1), static(2)} | read-create | current |
| hpnicfDot11SIDAPTemplateName OBJECT-TYPE Represents the name of AP template. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.4 | OCTET STRING | read-create | current |
| hpnicfDot11SIDModelAlias OBJECT-TYPE Represents the alias of AP model name. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.5 | OCTET STRING | read-create | current |
| hpnicfDot11SIDAPDescription OBJECT-TYPE This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.6 | OCTET STRING | read-create | current |
| hpnicfDot11SIDRowStatus OBJECT-TYPE The status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.7 | RowStatus | read-create | current |
| hpnicfDot11SIDAPName OBJECT-TYPE Represents the AP name. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.8 | OCTET STRING | read-create | current |
| hpnicfDot11SIDStatisInterv OBJECT-TYPE Represents the interval of radio statistic. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.9 | Integer32 | read-create | current |
| hpnicfDot11SIDAPBroadcastProbeReply OBJECT-TYPE Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.10 | TruthValue | read-create | current |
| hpnicfDot11SIDAPStaIdleTimerInterv OBJECT-TYPE Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.11 | Integer32 | read-create | current |
| hpnicfDot11SIDStaKeepAliveTimerInterv OBJECT-TYPE Represents the interval of the keep alive requests sent between AP and STA. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.12 | Integer32 | read-create | current |
| hpnicfDot11SIDAPCir OBJECT-TYPE Represents the committed information rate between AP and AC. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.13 | Integer32 | read-create | current |
| hpnicfDot11SIDAPCbs OBJECT-TYPE Represents the committed burst size between AP and AC. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.14 | Integer32 | read-create | current |
| hpnicfDot11SIDAPPriorityLevel OBJECT-TYPE This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.15 | Integer32 (0..7) | read-create | current |
| hpnicfDot11SIDAPElementID OBJECT-TYPE This object represents the AP element ID. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.16 | Integer32 | read-only | current |
| hpnicfDot11SIDAPDevDetectEnable OBJECT-TYPE Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object hpnicfDot11APWorkMode is monitor, device detection can not be enabled with object hpnicfDot11SIDAPDevDetectEnable. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.17 | TruthValue | read-create | current |
| hpnicfDot11SIDAPStatisIntervMode OBJECT-TYPE This object represents the mode of statics interval. normal - statics interval value between 10s to 120s realtime - statics interval value between 2s to 5s | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.18 | INTEGER {normal(1), realtime(2)} | read-create | current |
| hpnicfDot11SIDAPWorkModeCM OBJECT-TYPE Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. SemiMonitor - AP will supply WLAN service and Device detection is enabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.10.1.19 | INTEGER {normal(0), monitor(1), semimonitor(2)} | read-create | current |
| hpnicfDot11APSTVlanTable OBJECT-TYPE For each service policy, it could be bind to several VLANs. The table describes the relationship between VLAN and service policies. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11 | not-accessible | current | |
| hpnicfDot11APSTVlanEntry OBJECT-TYPE Each entry contains VLAN and service policy information for each specific radio of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1 | not-accessible | current | |
| hpnicfDot11CfgSTVLANID OBJECT-TYPE Represents the VLAN that current Service Policy have bind to. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.1 | Integer32 (0..4094) | read-create | current |
| hpnicfDot11CfgSTNASPortID OBJECT-TYPE Represents the NAS Port ID of current Service Policy for each specific radio of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.2 | OCTET STRING (SIZE(0..127)) | read-only | current |
| hpnicfDot11CfgServiceSetRowStatus OBJECT-TYPE The status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.3 | RowStatus | read-create | current |
| hpnicfDot11CfgSTNASID OBJECT-TYPE Represents the NAS ID of current Service Policy for each specific radio of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.3.11.1.4 | OCTET STRING (SIZE(0..127)) | read-only | current |
| hpnicfDot11RadioIntfConfigGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4 | |||
| hpnicfDot11RadioIntfConfigTable OBJECT-TYPE The table defines the parameters for radio in AP, as per radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1 | not-accessible | current | |
| hpnicfDot11RadioIntfConfigEntry OBJECT-TYPE Each entry contains information of each radio in AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1 | not-accessible | current | |
| hpnicfDot11RadioIfIdx OBJECT-TYPE Represents the Radio IfIndex of radio in AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.1 | Integer32 | not-accessible | current |
| hpnicfDot11RadioCfgBeaconIntvl OBJECT-TYPE Represents the interval for Beacon management frame. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.2 | Integer32 | read-write | current |
| hpnicfDot11RadioCfgDtimIntvl OBJECT-TYPE Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.3 | Integer32 | read-write | current |
| hpnicfDot11RadioCfgRtsThreshold OBJECT-TYPE Represents the current minimum size,in octets,of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.4 | Integer32 | read-write | current |
| hpnicfDot11RadioCfgFragThreshold OBJECT-TYPE Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.5 | Integer32 | read-write | current |
| hpnicfDot11RadioCfgShtRetryThld OBJECT-TYPE Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hpnicfDot11RadioRTSThreshold, that shall be made before a failure condition is indicated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.6 | Integer32 | read-write | current |
| hpnicfDot11RadioCfglongRtrThld OBJECT-TYPE Represents the maximum number of transmission attempts of a frame, the length of which is longer than hpnicfDot11RadioRTSThreshold, that shall be made before a failure condition is indicated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.7 | Integer32 | read-write | current |
| hpnicfDot11RadioCfgMaxRxLifetime OBJECT-TYPE Represents the elapsed time. After the time specified by hpnicfDot11RadioCfgMaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.8 | Unsigned32 | read-write | current |
| hpnicfDot11RadioCfgType OBJECT-TYPE Represents the radio will work with which 802.11 radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.9 | HpnicfDot11RadioType | read-write | current |
| hpnicfDot11RadioCfgChannel OBJECT-TYPE Represents the channel allocation of radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.10 | HpnicfDot11ChannelScopeType | read-write | current |
| hpnicfDot11RadioCfgMaxTxPwrLvl OBJECT-TYPE Represents the maximal transmit power scope for AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.11 | HpnicfDot11TxPwrLevelScopeType | read-write | current |
| hpnicfDot11RadioCfgPreambleLen OBJECT-TYPE Represents whether use long or short preamble for 802.11 MAC frame. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.12 | HpnicfDot11PreambleType | read-write | current |
| hpnicfDot11RadioCfgWorkMode OBJECT-TYPE Represents work mode of the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.13 | HpnicfDot11WorkMode | read-write | current |
| hpnicfDot11RadioCfgOnly11gEnable OBJECT-TYPE Represents whether enable only 802.11g radio mode or not. 'true' : Only 802.11g radio mode is enabled. 'false': Only 802.11g radio mode is disabled. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.14 | TruthValue | read-write | current |
| hpnicfDot11RadioCfgType2 OBJECT-TYPE Represents the radio will work with which 802.11 radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.15 | HpnicfDot11RadioType2 | read-write | current |
| hpnicfDot11RadioCfgRssithresholdCM OBJECT-TYPE Represents the minimum value of the RSSI. The clients with RSSI below this value will be refused to associate. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.1.1.16 | Integer32 | read-write | current |
| hpnicfDot11RadioIntfBindTable OBJECT-TYPE The table defines the binding information for each radio in AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2 | not-accessible | current | |
| hpnicfDot11RadioIntfBindEntry OBJECT-TYPE Each entry contains the radio interface binding information in AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1 | not-accessible | current | |
| hpnicfDot11RadioIntfBindSvcPlcyID OBJECT-TYPE Represents the ID of each service policy. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.1 | HpnicfDot11ServicePolicyIDType | not-accessible | current |
| hpnicfDot11RadioIntfBindIfIdx OBJECT-TYPE Represents the Ifindex of interface which is binded to the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.2 | Unsigned32 | read-create | current |
| hpnicfDot11RadioIntfBindRowStatus OBJECT-TYPE The status of this table entry. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.4.2.1.3 | RowStatus | read-create | current |
| hpnicfDot11DataRateConfigGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5 | |||
| hpnicfDot11DataRateConfigTable OBJECT-TYPE Table will provide data rate configuration for a specific radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1 | not-accessible | current | |
| hpnicfDot11DataRateConfigEntry OBJECT-TYPE Each entry of the table will provide data rate configuration for a specific radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1 | not-accessible | current | |
| hpnicfDot11RadioTypeID OBJECT-TYPE Represents the radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.1 | HpnicfDot11RadioType | not-accessible | current |
| hpnicfDot11SupportedRateSet OBJECT-TYPE Represents the supported rate set of a particular radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.2 | OCTET STRING (SIZE(0..255)) | read-write | current |
| hpnicfDot11MandatoryRateSet OBJECT-TYPE Represents the mandatory rate set of a particular radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.3 | OCTET STRING (SIZE(0..255)) | read-write | current |
| hpnicfDot11DisabledRateSet OBJECT-TYPE Represents the disabled rate set of a particular radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.4 | OCTET STRING (SIZE(0..255)) | read-write | current |
| hpnicfDot11SmartRateSet OBJECT-TYPE Represents the rate set of a particular radio type. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.5.1.1.5 | OCTET STRING (SIZE(0..255)) | read-write | current |
| hpnicfDot11InterfaceConfigGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6 | |||
| hpnicfDot11WlanEssIfTable OBJECT-TYPE This table is used to configure WLAN ESS interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1 | not-accessible | current | |
| hpnicfDot11WlanEssIfEntry OBJECT-TYPE Each entry contains the WLAN ESS interface configuration. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1 | not-accessible | current | |
| hpnicfDot11WlanEssIfNumber OBJECT-TYPE This node represents the WLAN ESS interface number. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.1 | Integer32 | not-accessible | current |
| hpnicfDot11WlanEssIfIndex OBJECT-TYPE This node represents the ifIndex of WLAN-ESS interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.2 | Integer32 | read-only | current |
| hpnicfDot11WlanEssRowStatus OBJECT-TYPE This node represents the WLAN ESS interface row status. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.1.1.3 | RowStatus | read-create | current |
| hpnicfDot11WlanBssIfTable OBJECT-TYPE This table is used to configure WLAN BSS interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2 | not-accessible | current | |
| hpnicfDot11WlanBssIfEntry OBJECT-TYPE Each entry contains the WLAN BSS interface configuration. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1 | not-accessible | current | |
| hpnicfDot11WlanBssIfNumber OBJECT-TYPE This node represents the WLAN BSS interface number. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.1 | Integer32 | not-accessible | current |
| hpnicfDot11WlanBssIfIndex OBJECT-TYPE This node represents the ifIndex of WLAN-BSS interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.2 | Integer32 | read-only | current |
| hpnicfDot11WlanBssRowStatus OBJECT-TYPE This node represents the WLAN BSS interface row status. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.2.1.3 | RowStatus | read-create | current |
| hpnicfDot11WLANEthernetIfTable OBJECT-TYPE This table is used to configure WLAN Ethernet interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3 | not-accessible | current | |
| hpnicfDot11WLANEthernetIfEntry OBJECT-TYPE Each entry contains the WLAN Ethernet interface configuration. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1 | not-accessible | current | |
| hpnicfDot11WlanEthernetIfNumber OBJECT-TYPE This node represents the WLAN Ethernet interface number. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.1 | Integer32 | not-accessible | current |
| hpnicfDot11WLANEthernetIfIndex OBJECT-TYPE This node represents the ifIndex of WLAN-Ethernet interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.2 | Integer32 | read-only | current |
| hpnicfDot11WlanEthernetRowStatus OBJECT-TYPE This node represents the Wlan Ethernet interface row status. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.3.1.3 | RowStatus | read-create | current |
| hpnicfDot11PortSecurityTable OBJECT-TYPE This table defines the WLAN security status for ESS, BSS, mesh and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, hpnicfPortSecurityTables should be used to configure port security. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4 | not-accessible | current | |
| hpnicfDot11PortSecurityEntry OBJECT-TYPE There is a row in this table for each ESS, BSS and WLAN-Ethernet interface.It is indexed using the object ifIndex in RFC1213-MIB. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1 | not-accessible | current | |
| hpnicfDot11PortSecurityMode OBJECT-TYPE Determines the security modes of the WLAN port. noRestrictions - The default value,no any security mode is set. userLoginSecureExt - Access to the port is denied until the port client is authorized (by 802.1X). psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk - The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk - This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext - Access to the port is denied until the port client is authenticated (by ext). | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.1 | INTEGER {noRestrictions(1), userLoginSecureExt(2), psk(3), macAddressAndPsk(4), userLoginSecureExtOrPsk(5), ext(6)} | read-write | current |
| hpnicfDot11SecurityUserLoginTxKeyType OBJECT-TYPE This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone - This means the key type is not set yet. userLoginTxKeyTypeDot11Key - This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4 session encryption. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.2 | INTEGER {userLoginTxKeyTypeNone(1), userLoginTxKeyTypeDot11Key(2), userLoginTxKeyTypeRsaRC4Key(3)} | read-write | current |
| hpnicfDot11SecurityPskKeyMode OBJECT-TYPE This is the password input mode. When input as pskKeyModePassPhrase, hpnicfDot11SecurePskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, hpnicfDot11SecurePskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.3 | INTEGER {pskKeyModeNone(1), pskKeyModePassPhrase(2), pskKeyModeRawKey(3)} | read-write | current |
| hpnicfDot11SecurityPskKeyString OBJECT-TYPE This is the password string used for psk authentication. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.4.1.4 | DisplayString | read-write | current |
| hpnicfDot11WlanMeshIfTable OBJECT-TYPE This table is used to configure WLAN mesh interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5 | not-accessible | current | |
| hpnicfDot11WlanMeshIfEntry OBJECT-TYPE Each entry contains the WLAN mesh interface configuration. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1 | not-accessible | current | |
| hpnicfDot11WlanMeshIfNumber OBJECT-TYPE This node represents the WLAN mesh interface number. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.1 | Integer32 | not-accessible | current |
| hpnicfDot11WlanMeshIfIndex OBJECT-TYPE This node represents the index of WLAN mesh interface. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.2 | Integer32 | read-only | current |
| hpnicfDot11WlanMeshRowStatus OBJECT-TYPE This node represents the WLAN mesh interface row status. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.6.5.1.3 | RowStatus | read-create | current |
| hpnicfDot11ACBackupGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.7 | |||
| hpnicfDot11BackupACAdrssIP OBJECT-TYPE This object represents the backup AC IP address. If the backup AC IP address is not configured, the object value is 0.0.0.0. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.7.1 | InetAddress | read-write | current |
| hpnicfDot11BackupACAdrssIPv6 OBJECT-TYPE This object represents the backup AC IPv6 address. If the backup AC IPv6 address is not configured, the object value is 0::0. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.7.2 | InetAddress | read-write | current |
| hpnicfDot11RadioElementConfigGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8 | |||
| hpnicfDot11nRadioCfgTable OBJECT-TYPE This table is used to configure dot11n on the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1 | not-accessible | current | |
| hpnicfDot11nRadioCfgEntry OBJECT-TYPE This entry contains the dot11n configuration on the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1 | not-accessible | current | |
| hpnicfDot11nRadioCfgIndex OBJECT-TYPE Represents index of the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.1 | HpnicfDot11RadioElementIndex | not-accessible | current |
| hpnicfDot11nAMpduEnable OBJECT-TYPE Enable the function of A-MPDU. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.2 | TruthValue | read-write | current |
| hpnicfDot11nAMsduEnable OBJECT-TYPE Enable the function of A-MSDU. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.3 | TruthValue | read-write | current |
| hpnicfDot11nClientDot11nOnly OBJECT-TYPE If radio type is 802.11an or 802.11gn, only permit clients of 11n mode. If radio type is 802.11ac, permit clients of 11n and 11ac mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.4 | TruthValue | read-write | current |
| hpnicfDot11nChanelBand OBJECT-TYPE Specify the bandwidth mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.5 | INTEGER {mode20(1), mode40(2), mode80(3)} | read-write | current |
| hpnicfDot11nShortGiEnable OBJECT-TYPE The function of Short GI. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.6 | TruthValue | read-write | current |
| hpnicfDot11nClientDot11acOnly OBJECT-TYPE Only permit clients of 11ac mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.1.1.7 | TruthValue | read-write | current |
| hpnicfDot11RadioWDSTable OBJECT-TYPE This table is used to configure WDS on the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2 | not-accessible | current | |
| hpnicfDot11RadioWDSEntry OBJECT-TYPE Each entry contains the WDS configuration on the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1 | not-accessible | current | |
| hpnicfDot11RadioWDSIndex OBJECT-TYPE Represents the element index of radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.1 | HpnicfDot11RadioElementIndex | not-accessible | current |
| hpnicfDot11RadioWDSMode OBJECT-TYPE Represents enable the WDS mode or not. nowds: The WDS mode is disabled. wds : The WDS mode is enabled | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.2 | INTEGER {nowds(1), wds(2)} | read-write | current |
| hpnicfDot11RadioWDSNetWorkID OBJECT-TYPE Represents the mesh ID of WDS. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.3 | OCTET STRING (SIZE(0..32)) | read-write | current |
| hpnicfDot11WDSSecPskKeyMode OBJECT-TYPE Represents the PSK mode of WDS. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.4 | INTEGER {pskKeyModeNone(1), pskKeyModePassPhrase(2), pskKeyModeRawKey(3)} | read-write | current |
| hpnicfDot11WDSSecPskKeyString OBJECT-TYPE Represents the PSK value of WDS. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.2.1.5 | DisplayString | read-write | current |
| hpnicfDot11nRadioCfg2Table OBJECT-TYPE This table is used to configure dot11n on the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3 | not-accessible | current | |
| hpnicfDot11nRadioCfg2Entry OBJECT-TYPE This entry contains the dot11n configuration on the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1 | not-accessible | current | |
| hpnicfDot11nRadioCfg2APIDIndex OBJECT-TYPE Represents index of the AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.1 | HpnicfDot11ObjectIDType | not-accessible | current |
| hpnicfDot11nRadioCfg2RadioIDIndex OBJECT-TYPE Represents index of the radio. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.2 | HpnicfDot11RadioScopeType | not-accessible | current |
| hpnicfDot11nRadioCfg2AMpduEnable OBJECT-TYPE Enable the function of A-MPDU. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.3 | TruthValue | read-write | current |
| hpnicfDot11nRadioCfg2AMsduEnable OBJECT-TYPE Enable the function of A-MSDU. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.4 | TruthValue | read-write | current |
| hpnicfDot11nRadioCfg2ClientDot11nOnly OBJECT-TYPE If radio type is 802.11an or 802.11gn, only permit clients of 11n mode. If radio type is 802.11ac, permit clients of 11n and 11ac mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.5 | TruthValue | read-write | current |
| hpnicfDot11nRadioCfg2ChannelBand OBJECT-TYPE Specify the bandwidth mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.6 | INTEGER {mode20(1), mode40(2), mode80(3)} | read-write | current |
| hpnicfDot11nRadioCfg2ShortGiEnable OBJECT-TYPE Enable the function of Short GI. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.7 | TruthValue | read-write | current |
| hpnicfDot11nRadioCfg2AMpduEnableCM OBJECT-TYPE Enable the function of A-MPDU. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.8 | INTEGER {off(0), on(1)} | read-write | current |
| hpnicfDot11nRadioCfg2ChannelBandCM OBJECT-TYPE Specify the bandwidth mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.9 | INTEGER {mode40(1), mode20(2)} | read-write | current |
| hpnicfDot11nRadioCfg2ShortGiEnableCM OBJECT-TYPE Enable the function of Short GI. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.10 | INTEGER {off(0), on(1)} | read-write | current |
| hpnicfDot11nRadioCfg2ClientDot11acOnly OBJECT-TYPE Only permit clients of 11ac mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.11 | TruthValue | read-write | current |
| hpnicfDot11nRadioCfg2ClientDot11nOnlyCM OBJECT-TYPE If radio type is 802.11an or 802.11gn, permit only clients of 11n mode. If radio type is 802.11ac, permit clients of both 11n and 11ac mode. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.8.3.1.12 | HpnicfDot11TruthValueCM | read-write | current |
| hpnicfDot11CfgNotifyGroup OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9 | |||
| hpnicfDot11CfgNotifications OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0 | |||
| hpnicfDot11CfgTrapVarObjects OBJECT-IDENTITY | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1 | |||
| hpnicfDot11PreConflictTemplateNum OBJECT-TYPE Represents previous service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.1 | Integer32 (1..1024) | accessible-for-notify | current |
| hpnicfDot11CurrConflictTemplateNum OBJECT-TYPE Represents current service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.2 | Integer32 (1..1024) | accessible-for-notify | current |
| hpnicfDot11ConflictCipherIdx OBJECT-TYPE Represents wep ID that conflicted with. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.3 | Integer32 (1..4) | accessible-for-notify | current |
| hpnicfDot11ConfigureAPID OBJECT-TYPE Represents which AP is configured. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.4 | HpnicfDot11ObjectIDType | accessible-for-notify | current |
| hpnicfDot11ConfigureRadioID OBJECT-TYPE Represents which radio in AP is configured. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.5 | HpnicfDot11RadioScopeType | accessible-for-notify | current |
| hpnicfDot11ConfigureAPMacAddress OBJECT-TYPE Represents MAC Address of AP. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.1.6 | MacAddress | accessible-for-notify | current |
Notifications
| Name | OID | Status |
|---|---|---|
| hpnicfDot11CfgCipherChange NOTIFICATION-TYPE This notification is sent when cipher type of corresponding service template is changed. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.1 | current |
| hpnicfDot11CfgPSKChange NOTIFICATION-TYPE This notification is sent when pre-shared key of corresponding service template is changed. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.2 | current |
| hpnicfDot11SSIDWepIDConflictTrap NOTIFICATION-TYPE This notification will be sent when the same wep ID is configured on two service policies. | 1.3.6.1.4.1.11.2.14.11.15.2.75.4.9.0.3 | current |