MIBs Depot

H3C-DOT11-CFG-MIB

Registered at
1.3.6.1.4.1.2011.10.2.75.4
Last updated
2010-09-25 18:00
Organization
Hangzhou H3C Technologies Co., Ltd.
Revisions
2010-09-25 18:00, 2010-09-02 18:00, 2009-07-29 18:00, 2009-05-07 20:00, 2009-03-20 15:30, 2008-11-07 15:30, 2008-07-09 18:00, 2008-02-25 18:00, 2007-12-21 18:00, 2007-10-09 16:55, 2007-06-19 18:00, 2007-04-27 20:00, 2007-02-01 20:00, 2006-05-10 19:00
Namespace
huawei
Source file
H3C-DOT11-CFG-MIB
Digest
sha256:4a854a74d95c69d6a323d4b5a707059936fe29a7bb7f4686520c9ef85133c005

Description

This MIB provides information about WLAN configuration. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC. Fit AP Applied in the enterprise environment, it will work under the control and management from AC. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP. Radio The chip set to receive and send wireless signal. Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.) Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association. MSDU MAC Service Data Unit, it is frame format defined by 802.11. TU It is 1,024 microseconds (ms), which is about 1 millisecond. AKM The authentication and key management method defined by 802.11i, and which includes 802.1x and pre-shared key.

Contact

Platform Team H3C Technologies Co., Ltd. Hai-Dian District Beijing P.R. China http://www.h3c.com Zip: 100085

Imports

FromSymbols
H3C-DOT11-REF-MIBH3cDot11AuthenType, H3cDot11ChannelScopeType, H3cDot11CirMode, H3cDot11ObjectIDType, H3cDot11PreambleType, H3cDot11RadioElementIndex, H3cDot11RadioScopeType, H3cDot11RadioType, H3cDot11RadioType2, H3cDot11SSIDEncryptModeType, H3cDot11SSIDStringType, H3cDot11SecIEStatusType, H3cDot11ServicePolicyIDType, H3cDot11TunnelSecSchemType, H3cDot11TxPwrLevelScopeType, H3cDot11WorkMode, h3cDot11, h3cDot11APElementIndex
IF-MIBifIndex
INET-ADDRESS-MIBInetAddress
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIInteger32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDateAndTime, DisplayString, IpAddress, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

H3C-DOT11-CFG-MIB
H3C-DOT11-REF-MIB
HUAWEI-3COM-OID-MIB
IANAifType-MIB
IF-MIB
INET-ADDRESS-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
h3cDot11GlobeConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.1
h3cDot11GlobalCountryCode
OBJECT-TYPE
Represents the country code for wireless network.
1.3.6.1.4.1.2011.10.2.75.4.1.1OCTET STRING (SIZE(3))read-writecurrent
h3cDot11StaKeepALiveTimerIntvl
OBJECT-TYPE
Represents the interval of the keep alive requests sent between AP and STA. Default value 0 : The keep alive function is disabled.
1.3.6.1.4.1.2011.10.2.75.4.1.2Unsigned32read-writecurrent
h3cDot11StaIdleTimerIntvl
OBJECT-TYPE
Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
1.3.6.1.4.1.2011.10.2.75.4.1.3Integer32read-writecurrent
h3cDot11BroadcastProbeReply
OBJECT-TYPE
Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
1.3.6.1.4.1.2011.10.2.75.4.1.4TruthValueread-writecurrent
h3cDot11APScanMode
OBJECT-TYPE
Represents the scanning mode for AP. The following values are supported: active(1), - AP will actively do scan. passive(2) - AP will passively do scan.
1.3.6.1.4.1.2011.10.2.75.4.1.5INTEGER {active(1), passive(2)}read-writecurrent
h3cDot11ACCtrlTunnelSecSupport
OBJECT-TYPE
Represents what security schemes are supported for CAPWAP Control tunnel.
1.3.6.1.4.1.2011.10.2.75.4.1.6H3cDot11TunnelSecSchemTyperead-writecurrent
h3cDot11ACDataTunnelSecSupport
OBJECT-TYPE
Represents what security schemes are supported for CAPWAP data tunnel. The cleartxt is the default scheme.
1.3.6.1.4.1.2011.10.2.75.4.1.7H3cDot11TunnelSecSchemTyperead-writecurrent
h3cDot11ACAutoAPSupport
OBJECT-TYPE
Represents enable the auto AP functionality or not. 'true' : The auto AP functionality is enabled. 'false': The auto AP functionality is disabled
1.3.6.1.4.1.2011.10.2.75.4.1.8TruthValueread-writecurrent
h3cDot11AutoAPName
OBJECT-TYPE
Represents the name of auto AP which need to be made persistent. When read the value from the node, NULL value be returned.
1.3.6.1.4.1.2011.10.2.75.4.1.9OCTET STRING (SIZE(0..127))read-writecurrent
h3cDot11PersistentName
OBJECT-TYPE
Represents the new name of auto AP after being made persistent. When read the value from the node, NULL value be returned.
1.3.6.1.4.1.2011.10.2.75.4.1.10OCTET STRING (SIZE(0..127))read-writecurrent
h3cDot11IntfTrapThreshold
OBJECT-TYPE
Represents threshold of interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
1.3.6.1.4.1.2011.10.2.75.4.1.11Integer32read-writecurrent
h3cDot11MonitorInterval
OBJECT-TYPE
Represents the monitoring interval. Default value 0 : The monitoring functionality is changed to real-time mode.
1.3.6.1.4.1.2011.10.2.75.4.1.12Unsigned32 (0 | 5..15)read-writecurrent
h3cDot11SampleInterval
OBJECT-TYPE
Represents the sampling interval. Default value 0 : The sampling functionality is disabled.
1.3.6.1.4.1.2011.10.2.75.4.1.13Unsigned32 (0 | 10..300)read-writecurrent
h3cDot11ChnlSwitChkInterval
OBJECT-TYPE
Represents the checking interval of channel switch.
1.3.6.1.4.1.2011.10.2.75.4.1.14Unsigned32 (8..180)read-writecurrent
h3cDot11APUserUplimit
OBJECT-TYPE
Represents the upper limit of user which has access to this AP.
1.3.6.1.4.1.2011.10.2.75.4.1.15Unsigned32 (0..65535)read-writecurrent
h3cDot11APL2IsolateEnable
OBJECT-TYPE
Represents enable the layer2 isolation or not. 'true' : The layer2 isolation functionality is enabled. 'false': The layer2 isolation functionality is disabled.
1.3.6.1.4.1.2011.10.2.75.4.1.16TruthValueread-writecurrent
h3cDot11APBSSIDSupportNum
OBJECT-TYPE
Represents the max number of BSSID supported by Current AP.
1.3.6.1.4.1.2011.10.2.75.4.1.17Integer32read-onlycurrent
h3cDot11APLastUpdateStatTime
OBJECT-TYPE
Represents date and time update statistic information lately.
1.3.6.1.4.1.2011.10.2.75.4.1.18DateAndTimeread-onlycurrent
h3cDot11APDoSProtectEnable
OBJECT-TYPE
Represents enable the DOS protection or not. 'true' : The DOS protection functionality is enabled. 'false': The DOS protection functionality is disabled.
1.3.6.1.4.1.2011.10.2.75.4.1.19TruthValueread-writecurrent
h3cDot11MaxAPPerIf
OBJECT-TYPE
Represents max AP number that can be connected to AC interface.
1.3.6.1.4.1.2011.10.2.75.4.1.20Unsigned32 (0..65535)read-writecurrent
h3cDot11SampleTimeStamp
OBJECT-TYPE
Represents the start time of current sample period.
1.3.6.1.4.1.2011.10.2.75.4.1.21DateAndTimeread-onlycurrent
h3cDot11UplinkTrackId
OBJECT-TYPE
Represents the track id of AP. Default value 0 : The uplink track function for AP is disabled.
1.3.6.1.4.1.2011.10.2.75.4.1.22Unsigned32read-writecurrent
h3cDot11RtCollectSwitch
OBJECT-TYPE
This object is used to turn on/off real-time statistics collection between AC and AP. If the value is true, h3cDot11RtCollectIntvl will take effect. Otherwise, h3cDot11RglCollectIntvl will take effect.
1.3.6.1.4.1.2011.10.2.75.4.1.23TruthValueread-writecurrent
h3cDot11RglCollectIntvl
OBJECT-TYPE
This object represents interval to regularly collect statistics from AC to AP.
1.3.6.1.4.1.2011.10.2.75.4.1.24Integer32read-writecurrent
h3cDot11RtCollectIntvl
OBJECT-TYPE
This object represents interval to collect real-time statistics from AC to AP.
1.3.6.1.4.1.2011.10.2.75.4.1.25Integer32read-writecurrent
h3cDot11AllAPCpuUsageThreshold
OBJECT-TYPE
The CPU usage threshold for all AP.
1.3.6.1.4.1.2011.10.2.75.4.1.26Integer32 (0..100)read-writecurrent
h3cDot11AllAPMemUsageThreshold
OBJECT-TYPE
The memory usage threshold for all AP.
1.3.6.1.4.1.2011.10.2.75.4.1.27Integer32 (0..100)read-writecurrent
h3cDot11AdjIntfTrapThreshold
OBJECT-TYPE
Represents threshold of adjacent interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
1.3.6.1.4.1.2011.10.2.75.4.1.28Integer32read-writecurrent
h3cDot11AllAPMonitorMode
OBJECT-TYPE
Represents what work mode for All AP. The following values are supported: normal, - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
1.3.6.1.4.1.2011.10.2.75.4.1.29INTEGER {normal(1), monitor(2), hybrid(3)}read-writecurrent
h3cDot11PolicyConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.2
h3cDot11RadioPolicyTable
OBJECT-TYPE
The table defines the parameters for radio policy, as per radio policy of CLI. One radio policy could be assigned to the different radios (AP).
1.3.6.1.4.1.2011.10.2.75.4.2.1not-accessiblecurrent
h3cDot11RadioPolicyEntry
OBJECT-TYPE
Each entry contains information of each radio policy.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1not-accessiblecurrent
h3cDot11RadioPolicyName
OBJECT-TYPE
Represents the name of radio policy.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.1OCTET STRING (SIZE(0..127))not-accessiblecurrent
h3cDot11BeaconInterval
OBJECT-TYPE
Represents the interval for Beacon management frame.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.2Integer32read-createcurrent
h3cDot11DtimInterval
OBJECT-TYPE
Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.3Integer32read-createcurrent
h3cDot11RtsThreshold
OBJECT-TYPE
Represents the current minimum size,in octets,of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.4Integer32read-createcurrent
h3cDot11FragThreshold
OBJECT-TYPE
Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.5Integer32read-createcurrent
h3cDot11ShortRetryThreshold
OBJECT-TYPE
Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to h3cDot11RTSThreshold, that shall be made before a failure condition is indicated.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.6Integer32read-createcurrent
h3cDot11LongRetryThreshold
OBJECT-TYPE
Represents the maximum number of transmission attempts of a frame, the length of which is longer than h3cDot11RTSThreshold, that shall be made before a failure condition is indicated.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.7Integer32read-createcurrent
h3cDot11MaxRxLifetime
OBJECT-TYPE
Represents the elapsed time. After the time specified by h3cDot11MaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.8Unsigned32read-createcurrent
h3cDot11RdoPolicyRowStatus
OBJECT-TYPE
The status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.9RowStatusread-createcurrent
h3cDot11RdoClientMaxCount
OBJECT-TYPE
Represent the maximum number of stations supported by this radio policy.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.10Integer32 (0..2147483647)read-createcurrent
h3cDot11BeaconIntervalMs
OBJECT-TYPE
Represents the interval for Beacon management frame.
1.3.6.1.4.1.2011.10.2.75.4.2.1.1.11Integer32read-createcurrent
h3cDot11ServicePolicyTable
OBJECT-TYPE
The table defines the parameters for ESS, as per service policy of CLI. One service policy could be assigned to the different radios (AP).
1.3.6.1.4.1.2011.10.2.75.4.2.2not-accessiblecurrent
h3cDot11ServicePolicyEntry
OBJECT-TYPE
Each entry contains information of each service policy.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1not-accessiblecurrent
h3cDot11ServicePolicyID
OBJECT-TYPE
Represents the ID of each service policy.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.1H3cDot11ServicePolicyIDTypenot-accessiblecurrent
h3cDot11SSIDName
OBJECT-TYPE
Represents the ESS. As per CLI, the value of service policy name will be SSID.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.2H3cDot11SSIDStringTyperead-createcurrent
h3cDot11SSIDHidden
OBJECT-TYPE
This attribute controls whether the SSID will be advertised in the beacon frame. If it is true, then SSID will not be advertised in the beacon frame.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.3TruthValueread-createcurrent
h3cDot11AuthenMode
OBJECT-TYPE
Represents the Authentication mode defined by 802.11.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.4H3cDot11AuthenTyperead-createcurrent
h3cDot11SSIDEncryptionMode
OBJECT-TYPE
Represents the encryption mode for this ESS.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.5H3cDot11SSIDEncryptModeTyperead-createcurrent
h3cDot11WlanInfBindingType
OBJECT-TYPE
Represents the service policy will bind to what kind of data forwarding interface.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.6OCTET STRINGread-createcurrent
h3cDot11WlanInfBindingID
OBJECT-TYPE
Represents the interface ID of the interface that ESS will bind to. If the value is set to -1, the binding will be removed.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.7Integer32read-createcurrent
h3cDot11SrvPolicyRowStatus
OBJECT-TYPE
The status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.8RowStatusread-createcurrent
h3cDot11ClientMaxCount
OBJECT-TYPE
Represent the maximum number of stations supported by this service policy.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.9Integer32 (0..2147483647)read-createcurrent
h3cDot11SPInCirMode
OBJECT-TYPE
CIR(committed information rate) mode of inbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.10H3cDot11CirModeread-createcurrent
h3cDot11SPInCirValue
OBJECT-TYPE
Represents the CIR of inbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.11Integer32read-createcurrent
h3cDot11SPOutCirMode
OBJECT-TYPE
CIR(committed information rate) mode of outbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.12H3cDot11CirModeread-createcurrent
h3cDot11SPOutCirValue
OBJECT-TYPE
Represents the CIR of outbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.13Integer32read-createcurrent
h3cDot11WlanInfPVID
OBJECT-TYPE
Represents the VLAN ID of SSID.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.14Integer32read-createcurrent
h3cDot11SPInCirStaticValue
OBJECT-TYPE
Represents the CIR of inbound direction for static CIR mode.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.15Integer32read-createcurrent
h3cDot11SPOutCirStaticValue
OBJECT-TYPE
Represents the CIR of outbound direction for static CIR mode.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.16Integer32read-createcurrent
h3cDot11SPIsolate
OBJECT-TYPE
If it is true, then stations connected with the service policy are isolated.
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.17TruthValueread-createcurrent
h3cDot11WAPIAuthServerIP
OBJECT-TYPE
Represents the IP address of the WAPI Authentication server
1.3.6.1.4.1.2011.10.2.75.4.2.2.1.18IpAddressread-createcurrent
h3cDot11ServicePolicyExtTable
OBJECT-TYPE
The table defines the parameters for ESS, as per service policy of CLI. When the value of h3cDot11SSIDEncryptionMode equals to cipher(2), more configuration for a ESS will be put into the table.
1.3.6.1.4.1.2011.10.2.75.4.2.3not-accessiblecurrent
h3cDot11ServicePolicyExtEntry
OBJECT-TYPE
Each entry contains information of each service policy under cipher(2) mode.
1.3.6.1.4.1.2011.10.2.75.4.2.3.1not-accessiblecurrent
h3cDot11ServicePolicyExtID
OBJECT-TYPE
Represents the ID of each service policy.
1.3.6.1.4.1.2011.10.2.75.4.2.3.1.1H3cDot11ServicePolicyIDTypenot-accessiblecurrent
h3cDot11SecIEStatus
OBJECT-TYPE
To enable the security Information element in the beacon and probe response frames sent by AP.
1.3.6.1.4.1.2011.10.2.75.4.2.3.1.2H3cDot11SecIEStatusTyperead-createcurrent
h3cDot11SecurityCiphers
OBJECT-TYPE
The WLAN system support the following cipher type for data frame encryption. wep40(2) tkip(4) aesccmp(16) wep104(32) wpisms4(64) wep128(128) For each service policy,it could support multiple cipher types at the same time.So the value of object could combine multiple value of cipher type above. When the value of node equals to zero, it means no configuration or undo operation.
1.3.6.1.4.1.2011.10.2.75.4.2.3.1.3INTEGERread-createcurrent
h3cDot11CipherKeyIndex
OBJECT-TYPE
Represents the key index of cipher key for packet. When h3cDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective.
1.3.6.1.4.1.2011.10.2.75.4.2.3.1.4INTEGERread-createcurrent
h3cDot11CipherKey
OBJECT-TYPE
Represents the cipher key for packet. When h3cDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective.
1.3.6.1.4.1.2011.10.2.75.4.2.3.1.5OCTET STRINGread-createcurrent
h3cDot11SrvPolicyExtRowStatus
OBJECT-TYPE
The status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.2.3.1.6RowStatusread-createcurrent
h3cDot11CipherKeyType
OBJECT-TYPE
Represents the cipher key type of h3cDot11CipherKey.
1.3.6.1.4.1.2011.10.2.75.4.2.3.1.7INTEGER {char(1), hex(2)}read-createcurrent
h3cDot11RadioPolicyExtTable
OBJECT-TYPE
The table defines the radio policy of each radio. It can't be modified if the radio policy is a default radio policy.
1.3.6.1.4.1.2011.10.2.75.4.2.4not-accessiblecurrent
h3cDot11RadioPolicyExtEntry
OBJECT-TYPE
Each entry contains information of each radio policy.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1not-accessiblecurrent
h3cDot11RPAPSerialID
OBJECT-TYPE
This object represents the Serial ID of AP.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.1OCTET STRING (SIZE(0..127))not-accessiblecurrent
h3cDot11RPRadioID
OBJECT-TYPE
This object represents each radio.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.2H3cDot11RadioScopeTypenot-accessiblecurrent
h3cDot11RPBeaconInterval
OBJECT-TYPE
This object represents the interval for Beacon management frame.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.3Integer32read-writecurrent
h3cDot11RPDtimInterval
OBJECT-TYPE
This object represents the number of beacon intervals that shall elapse between transmissions of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.4Integer32read-writecurrent
h3cDot11RPRtsThreshold
OBJECT-TYPE
This object represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.5Integer32read-writecurrent
h3cDot11RPFragThreshold
OBJECT-TYPE
This object represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.6Integer32read-writecurrent
h3cDot11RPShortRetryThreshold
OBJECT-TYPE
This object represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to h3cDot11RTSThreshold, that shall be made before a failure condition is indicated.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.7Integer32read-writecurrent
h3cDot11RPLongRetryThreshold
OBJECT-TYPE
This object represents the maximum number of transmission attempts of a frame, the length of which is longer than h3cDot11RTSThreshold, and that shall be made before a failure condition is indicated.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.8Integer32read-writecurrent
h3cDot11RPClientMaxCount
OBJECT-TYPE
This object represents the maximum number of stations supported by this radio policy.
1.3.6.1.4.1.2011.10.2.75.4.2.4.1.9Integer32 (0..2147483647)read-writecurrent
h3cDot11SrvPortSecurityTable
OBJECT-TYPE
This table defines the WLAN security status for ESS, BSS and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, h3cPortSecurityTables should be used to configure port security.
1.3.6.1.4.1.2011.10.2.75.4.2.5not-accessiblecurrent
h3cDot11SrvPortSecurityEntry
OBJECT-TYPE
There is a row in this table for service policy.
1.3.6.1.4.1.2011.10.2.75.4.2.5.1not-accessiblecurrent
h3cDot11SecurityServicePolicyID
OBJECT-TYPE
Represents the ID of each service policy.
1.3.6.1.4.1.2011.10.2.75.4.2.5.1.1H3cDot11ServicePolicyIDTypenot-accessiblecurrent
h3cDot11SrvPortSecurityMode
OBJECT-TYPE
Determines the security modes of the WLAN port. noRestrictions(1) The default value,no any security mode is set. userLoginSecureExt(2) Access to the port is denied until the port client is authorized (by 802.1X). psk(3) Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk(4) The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk(5) This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext(6) Access to the port is denied until the port client is authenticated (by ext).
1.3.6.1.4.1.2011.10.2.75.4.2.5.1.2INTEGER {noRestrictions(1), userLoginSecureExt(2), psk(3), macAddressAndPsk(4), userLoginSecureExtOrPsk(5), ext(6)}read-writecurrent
h3cDot11SrvSecurityKeyType
OBJECT-TYPE
This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone(1) This means the key type is not set yet. userLoginTxKeyTypeDot11Key(2) This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key(3) This selects the RC4 key for RSA RC4 session encryption.
1.3.6.1.4.1.2011.10.2.75.4.2.5.1.3INTEGER {userLoginTxKeyTypeNone(1), userLoginTxKeyTypeDot11Key(2), userLoginTxKeyTypeRsaRC4Key(3)}read-writecurrent
h3cDot11SrvSecurityPskKeyMode
OBJECT-TYPE
This is the password input mode. When input as pskKeyModePassPhrase, h3cDot11SrvSecurityPskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, h3cDot11SrvSecurityPskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'.
1.3.6.1.4.1.2011.10.2.75.4.2.5.1.4INTEGER {pskKeyModeNone(1), pskKeyModePassPhrase(2), pskKeyModeRawKey(3)}read-writecurrent
h3cDot11SrvSecurityPskKeyString
OBJECT-TYPE
This is the password string used for psk authentication.
1.3.6.1.4.1.2011.10.2.75.4.2.5.1.5DisplayString (SIZE(0..64))read-writecurrent
h3cDot11SrvPolicyExtendTable
OBJECT-TYPE
The table defines the parameters of each service policy.
1.3.6.1.4.1.2011.10.2.75.4.2.6not-accessiblecurrent
h3cDot11SrvPolicyExtendEntry
OBJECT-TYPE
Each entry contains information of each service policy.
1.3.6.1.4.1.2011.10.2.75.4.2.6.1not-accessiblecurrent
h3cDot11SPEnable
OBJECT-TYPE
Represents whether the service policy is enabled.
1.3.6.1.4.1.2011.10.2.75.4.2.6.1.1INTEGER {enable(1), disable(2)}read-writecurrent
h3cDot11APConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.3
h3cDot11APTemplateTable
OBJECT-TYPE
By AP template CLI, administrator will configure the parameters of AP by convenience. Before AP boot up and connect to AC by CAPWAP tunnel, administrator will create AP template for each AP. When AP connect to AC, AC will assign configuration to AP by h3cDot11APSerialID information in AP template.
1.3.6.1.4.1.2011.10.2.75.4.3.1not-accessiblecurrent
h3cDot11APTemplateEntry
OBJECT-TYPE
Each entry contains configuration information for each AP.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1not-accessiblecurrent
h3cDot11APTemplateName
OBJECT-TYPE
Represents the name of AP template.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.1OCTET STRING (SIZE(0..127))not-accessiblecurrent
h3cDot11APSerialID
OBJECT-TYPE
Represents AP serial id.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.2OCTET STRINGread-createcurrent
h3cDot11TemplateAPModelAlias
OBJECT-TYPE
Represents the alias of AP model name.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.3OCTET STRINGread-createcurrent
h3cDot11Description
OBJECT-TYPE
This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.4OCTET STRINGread-createcurrent
h3cDot11APWorkMode
OBJECT-TYPE
Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.5INTEGER {normal(1), monitor(2), hybrid(3)}read-createcurrent
h3cDot11APTemplateRowStatus
OBJECT-TYPE
The status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.6RowStatusread-createcurrent
h3cDot11APName
OBJECT-TYPE
Represents the AP name.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.7OCTET STRINGread-createcurrent
h3cDot11StatisInterv
OBJECT-TYPE
Represents the interval of radio statistic.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.8Integer32read-createcurrent
h3cDot11APBroadcastProbeReply
OBJECT-TYPE
Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.9TruthValueread-createcurrent
h3cDot11StaIdleTimerInterv
OBJECT-TYPE
Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.10Integer32read-createcurrent
h3cDot11StaKeepAliveTimerInterv
OBJECT-TYPE
Represents the interval of the keep alive requests sent between AP and STA.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.11Integer32read-createcurrent
h3cDot11APCir
OBJECT-TYPE
Represents the committed information rate between AP and AC.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.12Integer32read-createcurrent
h3cDot11APCbs
OBJECT-TYPE
Represents the committed burst size between AP and AC.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.13Integer32read-createcurrent
h3cDot11APPriorityLevel
OBJECT-TYPE
This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.14Integer32 (0..7)read-createcurrent
h3cDot11APElementID
OBJECT-TYPE
This object represents the AP element ID.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.15Integer32read-onlycurrent
h3cDot11APDevDetectEnable
OBJECT-TYPE
Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object h3cDot11APWorkMode is monitor, device detection can not be enabled with object h3cDot11APDevDetectEnable.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.16TruthValueread-createcurrent
h3cDot11APGetIPMethod
OBJECT-TYPE
This object represents the method how AP gets IP address.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.17INTEGER {dhcpAlloc(1), static(2)}read-createcurrent
h3cDot11StatisIntervMode
OBJECT-TYPE
This object represents the mode of statics interval. normal - statics interval value between 10s to 120s realtime - statics interval value between 2s to 5s
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.18INTEGER {normal(1), realtime(2)}read-createcurrent
h3cDot11ApTrapEnabled
OBJECT-TYPE
Represents whether the trap status is enabled or not. 'true' : Enable the trap status; 'false' : Disable the trap status.
1.3.6.1.4.1.2011.10.2.75.4.3.1.1.19TruthValueread-writecurrent
h3cDot11RadioToConfigTable
OBJECT-TYPE
Before AP connects to AC, administrator will configure radio parameter to each radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2not-accessiblecurrent
h3cDot11RadioToConfigEntry
OBJECT-TYPE
Each entry contains configuration information for each radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1not-accessiblecurrent
h3cDot11APTemplateNameCfg
OBJECT-TYPE
Represents the name of AP template.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.1OCTET STRING (SIZE(0..127))not-accessiblecurrent
h3cDot11CfgRadioID
OBJECT-TYPE
Represents each radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.2H3cDot11RadioScopeTypenot-accessiblecurrent
h3cDot11CfgRadioPolicyName
OBJECT-TYPE
Represents the name of radio policy.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.3OCTET STRINGread-writecurrent
h3cDot11CfgRadioType
OBJECT-TYPE
Represents the radio will work with which 802.11 radio type.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.4H3cDot11RadioTyperead-writecurrent
h3cDot11CfgChannel
OBJECT-TYPE
Represents the channel allocation of radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.5H3cDot11ChannelScopeTyperead-writecurrent
h3cDot11CfgMaxTxPowerLevel
OBJECT-TYPE
Represents the maximal transmit power scope for AP.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.6H3cDot11TxPwrLevelScopeTyperead-writecurrent
h3cDot11PreambleLen
OBJECT-TYPE
Represents whether use long or short preamble for 802.11 MAC frame. When h3cDot11CfgRadioType is either dot11b or dot11g, then value for h3cDot11PreambleLen will be valid. Othwise, the value for it will be invalid.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.7H3cDot11PreambleTyperead-writecurrent
h3cDot11CfgRadioStatus
OBJECT-TYPE
Represents the radio admin status whether is enabled or disabled.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.8TruthValueread-writecurrent
h3cDot11CfgRdElementID
OBJECT-TYPE
Represents the element ID of this radio. It comprises two parts. The highest 24 bits are AP element ID and the lowest 8 bits are radio ID.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.9Unsigned32read-onlycurrent
h3cDot11CfgWorkMode
OBJECT-TYPE
Represents work mode of the radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.10H3cDot11WorkModeread-writecurrent
h3cDot11CfgPwrAttValue
OBJECT-TYPE
Represents the value of power attenuation.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.11Integer32read-writecurrent
h3cDot11RadioTxArithmetic
OBJECT-TYPE
Represents the transmission arithmetic of the radio. The following values are supported: quality(1) - Consider the quality first during the transmission. bandwidth(2) - Consider the bandwidth first during the transmission.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.12INTEGER {quality(1), bandwidth(2)}read-writecurrent
h3cDot11CfgChannelLockStat
OBJECT-TYPE
Represents locked status of channel on the radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.13INTEGER {unlocked(1), locked(2)}read-writecurrent
h3cDot11CfgPowerLockStat
OBJECT-TYPE
Represents locked status of power on the radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.14INTEGER {unlocked(1), locked(2)}read-writecurrent
h3cDot11CfgLBRdGroupId
OBJECT-TYPE
Represents the load balance group ID allocated for the radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.15Unsigned32read-writecurrent
h3cDot11CfgRRMSDRdGroupId
OBJECT-TYPE
Represents the RRM self-decisive group ID allocated for the radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.16Unsigned32read-writecurrent
h3cDot11CfgRadioType2
OBJECT-TYPE
Represents the radio will work with which 802.11 radio type.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.17H3cDot11RadioType2read-writecurrent
h3cDot11CfgIDSEnable
OBJECT-TYPE
Represents whether intrusion detection is enabled for this radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.18TruthValueread-writecurrent
h3cDot11CfgSaEnable
OBJECT-TYPE
Represents whether spectrum analysis is enabled.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.19TruthValueread-writecurrent
h3cDot11CfgSaCltRtFFTData
OBJECT-TYPE
Represents whether to collect real-time FFT data for this radio.
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.20TruthValueread-writecurrent
h3cDot11CfgSaBand
OBJECT-TYPE
Represents which band of channels will be monitored when collection real-time FFT data is enabled for this radio. Detection of interference devices and air quality will also be affected. Each band responds to the following channels. dot11g (Channels 1-14) dot11aLower (channels 36-64) dot11aMiddle (channels 100-140) dot11aUpper (channels 149-165).
1.3.6.1.4.1.2011.10.2.75.4.3.2.1.21INTEGER {dot11g(1), dot11aLower(2), dot11aMiddle(3), dot11aUpper(4)}read-writecurrent
h3cDot11APServiceSetTable
OBJECT-TYPE
For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies.
1.3.6.1.4.1.2011.10.2.75.4.3.3not-accessiblecurrent
h3cDot11APServiceSetEntry
OBJECT-TYPE
Each entry contains service policy information for each specific radio of AP.
1.3.6.1.4.1.2011.10.2.75.4.3.3.1not-accessiblecurrent
h3cDot11CfgServicePolicyID
OBJECT-TYPE
Represents the ID of each service policy used by the AP.
1.3.6.1.4.1.2011.10.2.75.4.3.3.1.1H3cDot11ServicePolicyIDTypenot-accessiblecurrent
h3cDot11SrvSetRowStatus
OBJECT-TYPE
The status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.3.3.1.2RowStatusread-createcurrent
h3cDot11ServiceSetVlanId
OBJECT-TYPE
Represents the Vlan ID of BSS which is generated when service policy is binded with the Radio.
1.3.6.1.4.1.2011.10.2.75.4.3.3.1.3Integer32 (0..4094)read-createcurrent
h3cDot11APSysInfoSetTable
OBJECT-TYPE
The table of the system information for each AP.
1.3.6.1.4.1.2011.10.2.75.4.3.4not-accessiblecurrent
h3cDot11APSysInfoSetEntry
OBJECT-TYPE
The system information configuration for each AP.
1.3.6.1.4.1.2011.10.2.75.4.3.4.1not-accessiblecurrent
h3cDot11APSysNetID
OBJECT-TYPE
Represents the system Net ID for AP.
1.3.6.1.4.1.2011.10.2.75.4.3.4.1.1OCTET STRING (SIZE(0..127))read-writecurrent
h3cDot11APCpuUsageThreshold
OBJECT-TYPE
The CPU usage threshold for AP.
1.3.6.1.4.1.2011.10.2.75.4.3.4.1.2Integer32 (0..100)read-writecurrent
h3cDot11APMemUsageThreshold
OBJECT-TYPE
The memory usage threshold for AP.
1.3.6.1.4.1.2011.10.2.75.4.3.4.1.3Integer32 (0..100)read-writecurrent
h3cDot11APLimitTable
OBJECT-TYPE
For each connected APs, administrator could configure a series of limits. This table describes the limit information for AP(s).
1.3.6.1.4.1.2011.10.2.75.4.3.5not-accessiblecurrent
h3cDot11APLimitEntry
OBJECT-TYPE
Each entry contains the limit information for each AP.
1.3.6.1.4.1.2011.10.2.75.4.3.5.1not-accessiblecurrent
h3cDot11APSsidNumLimit
OBJECT-TYPE
Represents the upper limit of service template binded with this AP. All radios of AP share this limit. Default value 0 : There is no upper limit of service template binded with this AP.
1.3.6.1.4.1.2011.10.2.75.4.3.5.1.1Integer32 (0..65535)read-writecurrent
h3cDot11APUserCntLimit
OBJECT-TYPE
Represents the upper limit of user which has access to this AP. All BSSs binded with AP share this limit. Default value 0 : There is no upper limit of user which has access to this AP.
1.3.6.1.4.1.2011.10.2.75.4.3.5.1.2Integer32 (0..65535)read-writecurrent
h3cDot11APUserThreshold
OBJECT-TYPE
Represents the threshold of user which has access to this AP. All BSSs binded with AP share this limit. If the user counter is overflow, the trap will be sent. Default value 0 : There is no threshold of user which has access to this AP.
1.3.6.1.4.1.2011.10.2.75.4.3.5.1.3Integer32 (0..65535)read-writecurrent
h3cDot11APIfSetTable
OBJECT-TYPE
The table of the interface information for each AP.
1.3.6.1.4.1.2011.10.2.75.4.3.6not-accessiblecurrent
h3cDot11APIfSetEntry
OBJECT-TYPE
The interface information configuration for each AP.
1.3.6.1.4.1.2011.10.2.75.4.3.6.1not-accessiblecurrent
h3cDot11APSetIfIndex
OBJECT-TYPE
Represents the index for a interface.
1.3.6.1.4.1.2011.10.2.75.4.3.6.1.1Integer32not-accessiblecurrent
h3cDot11APIfAlias
OBJECT-TYPE
This object is an 'alias' name for the interface as specified by a network manager for AP.
1.3.6.1.4.1.2011.10.2.75.4.3.6.1.2DisplayStringread-writecurrent
h3cDot11APServiceVlanTable
OBJECT-TYPE
For all the radios on the AP, it could configure multiple service policies. The table describes the relationship between AP and service policies.
1.3.6.1.4.1.2011.10.2.75.4.3.7not-accessiblecurrent
h3cDot11APServiceVlanEntry
OBJECT-TYPE
Each entry contains service policy information for each AP.
1.3.6.1.4.1.2011.10.2.75.4.3.7.1not-accessiblecurrent
h3cDot11APServiceVlanSerialID
OBJECT-TYPE
This object represents AP serial id.
1.3.6.1.4.1.2011.10.2.75.4.3.7.1.1OCTET STRINGnot-accessiblecurrent
h3cDot11APServiceVlanSPID
OBJECT-TYPE
This object represents the ID of each service policy used by the AP.
1.3.6.1.4.1.2011.10.2.75.4.3.7.1.2H3cDot11ServicePolicyIDTypenot-accessiblecurrent
h3cDot11APServiceVlanId
OBJECT-TYPE
This object represents the VLAN ID of BSS which is generated when the service policy is bound to the radio.
1.3.6.1.4.1.2011.10.2.75.4.3.7.1.3Integer32 (0..4094)read-createcurrent
h3cDot11APServiceVlanRowStatus
OBJECT-TYPE
This object represents the status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.3.7.1.4RowStatusread-createcurrent
h3cDot11RadioConfigTable
OBJECT-TYPE
Before AP connects to AC, administrator will configure radio parameter to each radio.
1.3.6.1.4.1.2011.10.2.75.4.3.8not-accessiblecurrent
h3cDot11RadioConfigEntry
OBJECT-TYPE
Each entry contains configuration information for each radio.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1not-accessiblecurrent
h3cDot11RCAPSerialID
OBJECT-TYPE
This object represents the Serial ID of AP.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.1OCTET STRING (SIZE(0..127))not-accessiblecurrent
h3cDot11RCRadioID
OBJECT-TYPE
This object represents each radio.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.2H3cDot11RadioScopeTypenot-accessiblecurrent
h3cDot11RCRadioType
OBJECT-TYPE
This object represents the radio will work with which 802.11 radio type.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.3H3cDot11RadioTyperead-writecurrent
h3cDot11RCChannel
OBJECT-TYPE
This object represents the channel allocation of radio.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.4H3cDot11ChannelScopeTyperead-writecurrent
h3cDot11RCPreambleLen
OBJECT-TYPE
This object represents whether use long or short preamble for 802.11 MAC frame. When h3cDot11CfgRadioType is either dot11b or dot11g, then value for h3cDot11PreambleLen will be valid. Otherwise, the value for it will be invalid.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.5H3cDot11PreambleTyperead-writecurrent
h3cDot11RCPwrAttValue
OBJECT-TYPE
This object represents the value of power attenuation.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.6Integer32read-writecurrent
h3cDot11RCApPowerLevel
OBJECT-TYPE
Represents the maximal transmit power scope for AP.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.7H3cDot11TxPwrLevelScopeTyperead-writecurrent
h3cDot11RCDynamicChlState
OBJECT-TYPE
Enable/Disable dynamic channel selection.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.8TruthValueread-writecurrent
h3cDot11RCDynamicPowerState
OBJECT-TYPE
Enable/Disable dynamic power selection for the band.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.9TruthValueread-writecurrent
h3cDot11RCRadioStatus
OBJECT-TYPE
Represents the radio admin status whether is enabled or disabled.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.10TruthValueread-writecurrent
h3cDot11RCRadioRate
OBJECT-TYPE
Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format can be MCS X. The data transmit rates between AP and STA must fall into the configured rates. (Note: For 802.11n radios, the first value will be treated as a mandatory rate, and the second value will be treated as a supported rate. If you configure more than two rates, the configuration cannot take effect. If you configure only one rate, it is considered as the mandatory rate by default.)
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.11OCTET STRING (SIZE(0..255))read-writecurrent
h3cDot11RCPwrAdjustStepLength
OBJECT-TYPE
Power adjustment step-length in dBm.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.12Integer32read-onlycurrent
h3cDot11RCRadioType2
OBJECT-TYPE
This object represents the radio will work with which 802.11 radio type.
1.3.6.1.4.1.2011.10.2.75.4.3.8.1.13H3cDot11RadioType2read-writecurrent
h3cDot11RadioSSIDCfgTable
OBJECT-TYPE
For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies.
1.3.6.1.4.1.2011.10.2.75.4.3.9not-accessiblecurrent
h3cDot11RadioSSIDCfgEntry
OBJECT-TYPE
Each entry contains SSID configuration information for each radio.
1.3.6.1.4.1.2011.10.2.75.4.3.9.1not-accessiblecurrent
h3cDot11RadioSSIDSerialID
OBJECT-TYPE
This object represents the serial ID of AP.
1.3.6.1.4.1.2011.10.2.75.4.3.9.1.1H3cDot11ObjectIDTypenot-accessiblecurrent
h3cDot11RadioSSIDRadioID
OBJECT-TYPE
This object represents each radio.
1.3.6.1.4.1.2011.10.2.75.4.3.9.1.2H3cDot11RadioScopeTypenot-accessiblecurrent
h3cDot11RadioSSIDWLANID
OBJECT-TYPE
This object represents the WLAN ID of the BSSID.
1.3.6.1.4.1.2011.10.2.75.4.3.9.1.3Integer32not-accessiblecurrent
h3cDot11RadioSSIDIndex
OBJECT-TYPE
This object represents the ID of each service policy used by the radio.
1.3.6.1.4.1.2011.10.2.75.4.3.9.1.4H3cDot11ServicePolicyIDTyperead-createcurrent
h3cDot11RadioBSSID
OBJECT-TYPE
As MAC address format, it is used to identify BSS.
1.3.6.1.4.1.2011.10.2.75.4.3.9.1.5MacAddressread-onlycurrent
h3cDot11RadioSSIDRowStatus
OBJECT-TYPE
RowStatus.
1.3.6.1.4.1.2011.10.2.75.4.3.9.1.6RowStatusread-createcurrent
h3cDot11APSerialIDTable
OBJECT-TYPE
The table will provide the general information about APs.
1.3.6.1.4.1.2011.10.2.75.4.3.10not-accessiblecurrent
h3cDot11APSerialIDEntry
OBJECT-TYPE
Each entry contains the general information of an AP.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1not-accessiblecurrent
h3cDot11SIDAPSerialID
OBJECT-TYPE
Represents AP serial id.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.1OCTET STRINGnot-accessiblecurrent
h3cDot11SIDAPWorkMode
OBJECT-TYPE
Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.2INTEGER {normal(1), monitor(2), hybrid(3)}read-createcurrent
h3cDot11SIDAPGetIPMethod
OBJECT-TYPE
This object represents the method how AP gets IP address.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.3INTEGER {dhcpAlloc(1), static(2)}read-createcurrent
h3cDot11SIDAPTemplateName
OBJECT-TYPE
Represents the name of AP template.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.4OCTET STRINGread-createcurrent
h3cDot11SIDModelAlias
OBJECT-TYPE
Represents the alias of AP model name.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.5OCTET STRINGread-createcurrent
h3cDot11SIDAPDescription
OBJECT-TYPE
This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.6OCTET STRINGread-createcurrent
h3cDot11SIDRowStatus
OBJECT-TYPE
The status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.7RowStatusread-createcurrent
h3cDot11SIDAPName
OBJECT-TYPE
Represents the AP name.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.8OCTET STRINGread-createcurrent
h3cDot11SIDStatisInterv
OBJECT-TYPE
Represents the interval of radio statistic.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.9Integer32read-createcurrent
h3cDot11SIDAPBroadcastProbeReply
OBJECT-TYPE
Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.10TruthValueread-createcurrent
h3cDot11SIDAPStaIdleTimerInterv
OBJECT-TYPE
Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.11Integer32read-createcurrent
h3cDot11SIDStaKeepAliveTimerInterv
OBJECT-TYPE
Represents the interval of the keep alive requests sent between AP and STA.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.12Integer32read-createcurrent
h3cDot11SIDAPCir
OBJECT-TYPE
Represents the committed information rate between AP and AC.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.13Integer32read-createcurrent
h3cDot11SIDAPCbs
OBJECT-TYPE
Represents the committed burst size between AP and AC.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.14Integer32read-createcurrent
h3cDot11SIDAPPriorityLevel
OBJECT-TYPE
This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.15Integer32 (0..7)read-createcurrent
h3cDot11SIDAPElementID
OBJECT-TYPE
This object represents the AP element ID.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.16Integer32read-onlycurrent
h3cDot11SIDAPDevDetectEnable
OBJECT-TYPE
Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object h3cDot11APWorkMode is monitor, device detection can not be enabled with object h3cDot11SIDAPDevDetectEnable.
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.17TruthValueread-createcurrent
h3cDot11SIDAPStatisIntervMode
OBJECT-TYPE
This object represents the mode of statics interval. normal - statics interval value between 10s to 120s realtime - statics interval value between 2s to 5s
1.3.6.1.4.1.2011.10.2.75.4.3.10.1.18INTEGER {normal(1), realtime(2)}read-createcurrent
h3cDot11APSTVlanTable
OBJECT-TYPE
For each service policy, it could be bind to several VLANs. The table describes the relationship between VLAN and service policies.
1.3.6.1.4.1.2011.10.2.75.4.3.11not-accessiblecurrent
h3cDot11APSTVlanEntry
OBJECT-TYPE
Each entry contains VLAN and service policy information for each specific radio of AP.
1.3.6.1.4.1.2011.10.2.75.4.3.11.1not-accessiblecurrent
h3cDot11CfgSTVLANID
OBJECT-TYPE
Represents the VLAN that current Service Policy have bind to.
1.3.6.1.4.1.2011.10.2.75.4.3.11.1.1Integer32 (0..4094)read-createcurrent
h3cDot11CfgSTNASPortID
OBJECT-TYPE
Represents the NAS Port ID of current Service Policy for each specific radio of AP.
1.3.6.1.4.1.2011.10.2.75.4.3.11.1.2OCTET STRING (SIZE(0..127))read-onlycurrent
h3cDot11CfgServiceSetRowStatus
OBJECT-TYPE
The status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.3.11.1.3RowStatusread-createcurrent
h3cDot11RadioIntfConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.4
h3cDot11RadioIntfConfigTable
OBJECT-TYPE
The table defines the parameters for radio in AP, as per radio.
1.3.6.1.4.1.2011.10.2.75.4.4.1not-accessiblecurrent
h3cDot11RadioIntfConfigEntry
OBJECT-TYPE
Each entry contains information of each radio in AP.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1not-accessiblecurrent
h3cDot11RadioIfIdx
OBJECT-TYPE
Represents the Radio IfIndex of radio in AP.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.1Integer32not-accessiblecurrent
h3cDot11RadioCfgBeaconIntvl
OBJECT-TYPE
Represents the interval for Beacon management frame.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.2Integer32read-writecurrent
h3cDot11RadioCfgDtimIntvl
OBJECT-TYPE
Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.3Integer32read-writecurrent
h3cDot11RadioCfgRtsThreshold
OBJECT-TYPE
Represents the current minimum size,in octets,of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.4Integer32read-writecurrent
h3cDot11RadioCfgFragThreshold
OBJECT-TYPE
Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.5Integer32read-writecurrent
h3cDot11RadioCfgShtRetryThld
OBJECT-TYPE
Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to h3cDot11RadioRTSThreshold, that shall be made before a failure condition is indicated.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.6Integer32read-writecurrent
h3cDot11RadioCfglongRtrThld
OBJECT-TYPE
Represents the maximum number of transmission attempts of a frame, the length of which is longer than h3cDot11RadioRTSThreshold, that shall be made before a failure condition is indicated.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.7Integer32read-writecurrent
h3cDot11RadioCfgMaxRxLifetime
OBJECT-TYPE
Represents the elapsed time. After the time specified by h3cDot11RadioCfgMaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.8Unsigned32read-writecurrent
h3cDot11RadioCfgType
OBJECT-TYPE
Represents the radio will work with which 802.11 radio type.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.9H3cDot11RadioTyperead-writecurrent
h3cDot11RadioCfgChannel
OBJECT-TYPE
Represents the channel allocation of radio.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.10H3cDot11ChannelScopeTyperead-writecurrent
h3cDot11RadioCfgMaxTxPwrLvl
OBJECT-TYPE
Represents the maximal transmit power scope for AP.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.11H3cDot11TxPwrLevelScopeTyperead-writecurrent
h3cDot11RadioCfgPreambleLen
OBJECT-TYPE
Represents whether use long or short preamble for 802.11 MAC frame.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.12H3cDot11PreambleTyperead-writecurrent
h3cDot11RadioCfgWorkMode
OBJECT-TYPE
Represents work mode of the radio.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.13H3cDot11WorkModeread-writecurrent
h3cDot11RadioCfgOnly11gEnable
OBJECT-TYPE
Represents whether enable only 802.11g radio mode or not. 'true' : Only 802.11g radio mode is enabled. 'false': Only 802.11g radio mode is disabled.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.14TruthValueread-writecurrent
h3cDot11RadioCfgType2
OBJECT-TYPE
Represents the radio will work with which 802.11 radio type.
1.3.6.1.4.1.2011.10.2.75.4.4.1.1.15H3cDot11RadioType2read-writecurrent
h3cDot11RadioIntfBindTable
OBJECT-TYPE
The table defines the binding information for each radio in AP.
1.3.6.1.4.1.2011.10.2.75.4.4.2not-accessiblecurrent
h3cDot11RadioIntfBindEntry
OBJECT-TYPE
Each entry contains the radio interface binding information in AP.
1.3.6.1.4.1.2011.10.2.75.4.4.2.1not-accessiblecurrent
h3cDot11RadioIntfBindSvcPlcyID
OBJECT-TYPE
Represents the ID of each service policy.
1.3.6.1.4.1.2011.10.2.75.4.4.2.1.1H3cDot11ServicePolicyIDTypenot-accessiblecurrent
h3cDot11RadioIntfBindIfIdx
OBJECT-TYPE
Represents the Ifindex of interface which is binded to the radio.
1.3.6.1.4.1.2011.10.2.75.4.4.2.1.2Unsigned32read-createcurrent
h3cDot11RadioIntfBindRowStatus
OBJECT-TYPE
The status of this table entry.
1.3.6.1.4.1.2011.10.2.75.4.4.2.1.3RowStatusread-createcurrent
h3cDot11DataRateConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.5
h3cDot11DataRateConfigTable
OBJECT-TYPE
Table will provide data rate configuration for a specific radio type.
1.3.6.1.4.1.2011.10.2.75.4.5.1not-accessiblecurrent
h3cDot11DataRateConfigEntry
OBJECT-TYPE
Each entry of the table will provide data rate configuration for a specific radio type.
1.3.6.1.4.1.2011.10.2.75.4.5.1.1not-accessiblecurrent
h3cDot11RadioTypeID
OBJECT-TYPE
Represents the radio type.
1.3.6.1.4.1.2011.10.2.75.4.5.1.1.1H3cDot11RadioTypenot-accessiblecurrent
h3cDot11SupportedRateSet
OBJECT-TYPE
Represents the supported rate set of a particular radio type.
1.3.6.1.4.1.2011.10.2.75.4.5.1.1.2OCTET STRING (SIZE(0..255))read-writecurrent
h3cDot11MandatoryRateSet
OBJECT-TYPE
Represents the mandatory rate set of a particular radio type.
1.3.6.1.4.1.2011.10.2.75.4.5.1.1.3OCTET STRING (SIZE(0..255))read-writecurrent
h3cDot11DisabledRateSet
OBJECT-TYPE
Represents the disabled rate set of a particular radio type.
1.3.6.1.4.1.2011.10.2.75.4.5.1.1.4OCTET STRING (SIZE(0..255))read-writecurrent
h3cDot11SmartRateSet
OBJECT-TYPE
Represents the rate set of a particular radio type.
1.3.6.1.4.1.2011.10.2.75.4.5.1.1.5OCTET STRING (SIZE(0..255))read-writecurrent
h3cDot11InterfaceConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.6
h3cDot11WlanEssIfTable
OBJECT-TYPE
This table is used to configure WLAN ESS interface.
1.3.6.1.4.1.2011.10.2.75.4.6.1not-accessiblecurrent
h3cDot11WlanEssIfEntry
OBJECT-TYPE
Each entry contains the WLAN ESS interface configuration.
1.3.6.1.4.1.2011.10.2.75.4.6.1.1not-accessiblecurrent
h3cDot11WlanEssIfNumber
OBJECT-TYPE
This node represents the WLAN ESS interface number.
1.3.6.1.4.1.2011.10.2.75.4.6.1.1.1Integer32not-accessiblecurrent
h3cDot11WlanEssIfIndex
OBJECT-TYPE
This node represents the ifIndex of WLAN-ESS interface.
1.3.6.1.4.1.2011.10.2.75.4.6.1.1.2Integer32read-onlycurrent
h3cDot11WlanEssRowStatus
OBJECT-TYPE
This node represents the WLAN ESS interface row status.
1.3.6.1.4.1.2011.10.2.75.4.6.1.1.3RowStatusread-createcurrent
h3cDot11WlanBssIfTable
OBJECT-TYPE
This table is used to configure WLAN BSS interface.
1.3.6.1.4.1.2011.10.2.75.4.6.2not-accessiblecurrent
h3cDot11WlanBssIfEntry
OBJECT-TYPE
Each entry contains the WLAN BSS interface configuration.
1.3.6.1.4.1.2011.10.2.75.4.6.2.1not-accessiblecurrent
h3cDot11WlanBssIfNumber
OBJECT-TYPE
This node represents the WLAN BSS interface number.
1.3.6.1.4.1.2011.10.2.75.4.6.2.1.1Integer32not-accessiblecurrent
h3cDot11WlanBssIfIndex
OBJECT-TYPE
This node represents the ifIndex of WLAN-BSS interface.
1.3.6.1.4.1.2011.10.2.75.4.6.2.1.2Integer32read-onlycurrent
h3cDot11WlanBssRowStatus
OBJECT-TYPE
This node represents the WLAN BSS interface row status.
1.3.6.1.4.1.2011.10.2.75.4.6.2.1.3RowStatusread-createcurrent
h3cDot11WLANEthernetIfTable
OBJECT-TYPE
This table is used to configure WLAN Ethernet interface.
1.3.6.1.4.1.2011.10.2.75.4.6.3not-accessiblecurrent
h3cDot11WLANEthernetIfEntry
OBJECT-TYPE
Each entry contains the WLAN Ethernet interface configuration.
1.3.6.1.4.1.2011.10.2.75.4.6.3.1not-accessiblecurrent
h3cDot11WlanEthernetIfNumber
OBJECT-TYPE
This node represents the WLAN Ethernet interface number.
1.3.6.1.4.1.2011.10.2.75.4.6.3.1.1Integer32not-accessiblecurrent
h3cDot11WLANEthernetIfIndex
OBJECT-TYPE
This node represents the ifIndex of WLAN-Ethernet interface.
1.3.6.1.4.1.2011.10.2.75.4.6.3.1.2Integer32read-onlycurrent
h3cDot11WlanEthernetRowStatus
OBJECT-TYPE
This node represents the Wlan Ethernet interface row status.
1.3.6.1.4.1.2011.10.2.75.4.6.3.1.3RowStatusread-createcurrent
h3cDot11PortSecurityTable
OBJECT-TYPE
This table defines the WLAN security status for ESS, BSS, mesh and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, h3cPortSecurityTables should be used to configure port security.
1.3.6.1.4.1.2011.10.2.75.4.6.4not-accessiblecurrent
h3cDot11PortSecurityEntry
OBJECT-TYPE
There is a row in this table for each ESS, BSS and WLAN-Ethernet interface.It is indexed using the object ifIndex in RFC1213-MIB.
1.3.6.1.4.1.2011.10.2.75.4.6.4.1not-accessiblecurrent
h3cDot11PortSecurityMode
OBJECT-TYPE
Determines the security modes of the WLAN port. noRestrictions(1) The default value,no any security mode is set. userLoginSecureExt(2) Access to the port is denied until the port client is authorized (by 802.1X). psk(3) Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk(4) The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk(5) This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext(6) Access to the port is denied until the port client is authenticated (by ext).
1.3.6.1.4.1.2011.10.2.75.4.6.4.1.1INTEGER {noRestrictions(1), userLoginSecureExt(2), psk(3), macAddressAndPsk(4), userLoginSecureExtOrPsk(5), ext(6)}read-writecurrent
h3cDot11SecurityUserLoginTxKeyType
OBJECT-TYPE
This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone(1) This means the key type is not set yet. userLoginTxKeyTypeDot11Key(2) This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key(3) This selects the RC4 key for RSA RC4 session encryption.
1.3.6.1.4.1.2011.10.2.75.4.6.4.1.2INTEGER {userLoginTxKeyTypeNone(1), userLoginTxKeyTypeDot11Key(2), userLoginTxKeyTypeRsaRC4Key(3)}read-writecurrent
h3cDot11SecurityPskKeyMode
OBJECT-TYPE
This is the password input mode. When input as pskKeyModePassPhrase, h3cDot11SecurePskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, h3cDot11SecurePskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'.
1.3.6.1.4.1.2011.10.2.75.4.6.4.1.3INTEGER {pskKeyModeNone(1), pskKeyModePassPhrase(2), pskKeyModeRawKey(3)}read-writecurrent
h3cDot11SecurityPskKeyString
OBJECT-TYPE
This is the password string used for psk authentication.
1.3.6.1.4.1.2011.10.2.75.4.6.4.1.4DisplayStringread-writecurrent
h3cDot11WlanMeshIfTable
OBJECT-TYPE
This table is used to configure WLAN mesh interface.
1.3.6.1.4.1.2011.10.2.75.4.6.5not-accessiblecurrent
h3cDot11WlanMeshIfEntry
OBJECT-TYPE
Each entry contains the WLAN mesh interface configuration.
1.3.6.1.4.1.2011.10.2.75.4.6.5.1not-accessiblecurrent
h3cDot11WlanMeshIfNumber
OBJECT-TYPE
This node represents the WLAN mesh interface number.
1.3.6.1.4.1.2011.10.2.75.4.6.5.1.1Integer32not-accessiblecurrent
h3cDot11WlanMeshIfIndex
OBJECT-TYPE
This node represents the index of WLAN mesh interface.
1.3.6.1.4.1.2011.10.2.75.4.6.5.1.2Integer32read-onlycurrent
h3cDot11WlanMeshRowStatus
OBJECT-TYPE
This node represents the WLAN mesh interface row status.
1.3.6.1.4.1.2011.10.2.75.4.6.5.1.3RowStatusread-createcurrent
h3cDot11ACBackupGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.7
h3cDot11BackupACAdrssIP
OBJECT-TYPE
This object represents the backup AC IP address. If the backup AC IP address is not configured, the object value is 0.0.0.0.
1.3.6.1.4.1.2011.10.2.75.4.7.1InetAddressread-writecurrent
h3cDot11BackupACAdrssIPv6
OBJECT-TYPE
This object represents the backup AC IPv6 address. If the backup AC IPv6 address is not configured, the object value is 0::0.
1.3.6.1.4.1.2011.10.2.75.4.7.2InetAddressread-writecurrent
h3cDot11RadioElementConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.8
h3cDot11nRadioCfgTable
OBJECT-TYPE
This table is used to configure dot11n on the radio.
1.3.6.1.4.1.2011.10.2.75.4.8.1not-accessiblecurrent
h3cDot11nRadioCfgEntry
OBJECT-TYPE
This entry contains the dot11n configuration on the radio.
1.3.6.1.4.1.2011.10.2.75.4.8.1.1not-accessiblecurrent
h3cDot11nRadioCfgIndex
OBJECT-TYPE
Represents index of the radio.
1.3.6.1.4.1.2011.10.2.75.4.8.1.1.1H3cDot11RadioElementIndexnot-accessiblecurrent
h3cDot11nAMpduEnable
OBJECT-TYPE
Enable the function of A-MPDU.
1.3.6.1.4.1.2011.10.2.75.4.8.1.1.2TruthValueread-writecurrent
h3cDot11nAMsduEnable
OBJECT-TYPE
Enable the function of A-MSDU.
1.3.6.1.4.1.2011.10.2.75.4.8.1.1.3TruthValueread-writecurrent
h3cDot11nClientDot11nOnly
OBJECT-TYPE
Only permit clients of 11n mode.
1.3.6.1.4.1.2011.10.2.75.4.8.1.1.4TruthValueread-writecurrent
h3cDot11nChanelBand
OBJECT-TYPE
Specify the bandwidth mode.
1.3.6.1.4.1.2011.10.2.75.4.8.1.1.5INTEGER {mode20(1), mode40(2)}read-writecurrent
h3cDot11nShortGiEnable
OBJECT-TYPE
The function of Short GI.
1.3.6.1.4.1.2011.10.2.75.4.8.1.1.6TruthValueread-writecurrent
h3cDot11RadioWDSTable
OBJECT-TYPE
This table is used to configure WDS on the radio.
1.3.6.1.4.1.2011.10.2.75.4.8.2not-accessiblecurrent
h3cDot11RadioWDSEntry
OBJECT-TYPE
Each entry contains the WDS configuration on the radio.
1.3.6.1.4.1.2011.10.2.75.4.8.2.1not-accessiblecurrent
h3cDot11RadioWDSIndex
OBJECT-TYPE
Represents the element index of radio.
1.3.6.1.4.1.2011.10.2.75.4.8.2.1.1H3cDot11RadioElementIndexnot-accessiblecurrent
h3cDot11RadioWDSMode
OBJECT-TYPE
Represents enable the WDS mode or not. nowds: The WDS mode is disabled. wds : The WDS mode is enabled
1.3.6.1.4.1.2011.10.2.75.4.8.2.1.2INTEGER {nowds(1), wds(2)}read-writecurrent
h3cDot11RadioWDSNetWorkID
OBJECT-TYPE
Represents the mesh ID of WDS.
1.3.6.1.4.1.2011.10.2.75.4.8.2.1.3OCTET STRING (SIZE(0..32))read-writecurrent
h3cDot11WDSSecPskKeyMode
OBJECT-TYPE
Represents the PSK mode of WDS.
1.3.6.1.4.1.2011.10.2.75.4.8.2.1.4INTEGER {pskKeyModeNone(1), pskKeyModePassPhrase(2), pskKeyModeRawKey(3)}read-writecurrent
h3cDot11WDSSecPskKeyString
OBJECT-TYPE
Represents the PSK value of WDS.
1.3.6.1.4.1.2011.10.2.75.4.8.2.1.5DisplayStringread-writecurrent
h3cDot11nRadioCfg2Table
OBJECT-TYPE
This table is used to configure dot11n on the radio.
1.3.6.1.4.1.2011.10.2.75.4.8.3not-accessiblecurrent
h3cDot11nRadioCfg2Entry
OBJECT-TYPE
This entry contains the dot11n configuration on the radio.
1.3.6.1.4.1.2011.10.2.75.4.8.3.1not-accessiblecurrent
h3cDot11nRadioCfg2APIDIndex
OBJECT-TYPE
Represents index of the AP.
1.3.6.1.4.1.2011.10.2.75.4.8.3.1.1H3cDot11ObjectIDTypenot-accessiblecurrent
h3cDot11nRadioCfg2RadioIDIndex
OBJECT-TYPE
Represents index of the radio.
1.3.6.1.4.1.2011.10.2.75.4.8.3.1.2H3cDot11RadioScopeTypenot-accessiblecurrent
h3cDot11nRadioCfg2AMpduEnable
OBJECT-TYPE
Enable the function of A-MPDU.
1.3.6.1.4.1.2011.10.2.75.4.8.3.1.3TruthValueread-writecurrent
h3cDot11nRadioCfg2AMsduEnable
OBJECT-TYPE
Enable the function of A-MSDU.
1.3.6.1.4.1.2011.10.2.75.4.8.3.1.4TruthValueread-writecurrent
h3cDot11nRadioCfg2ClientDot11nOnly
OBJECT-TYPE
Only permit clients of 11n mode.
1.3.6.1.4.1.2011.10.2.75.4.8.3.1.5TruthValueread-writecurrent
h3cDot11nRadioCfg2ChannelBand
OBJECT-TYPE
Specify the bandwidth mode.
1.3.6.1.4.1.2011.10.2.75.4.8.3.1.6INTEGER {mode20(1), mode40(2)}read-writecurrent
h3cDot11nRadioCfg2ShortGiEnable
OBJECT-TYPE
Enable the function of Short GI.
1.3.6.1.4.1.2011.10.2.75.4.8.3.1.7TruthValueread-writecurrent
h3cDot11CfgNotifyGroup
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.9
h3cDot11CfgNotifications
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.9.0
h3cDot11CfgTrapVarObjects
OBJECT-IDENTITY
1.3.6.1.4.1.2011.10.2.75.4.9.1
h3cDot11PreConflictTemplateNum
OBJECT-TYPE
Represents previous service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration.
1.3.6.1.4.1.2011.10.2.75.4.9.1.1Integer32 (1..1024)accessible-for-notifycurrent
h3cDot11CurrConflictTemplateNum
OBJECT-TYPE
Represents current service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration.
1.3.6.1.4.1.2011.10.2.75.4.9.1.2Integer32 (1..1024)accessible-for-notifycurrent
h3cDot11ConflictCipherIdx
OBJECT-TYPE
Represents wep ID that conflicted with.
1.3.6.1.4.1.2011.10.2.75.4.9.1.3Integer32 (1..4)accessible-for-notifycurrent
h3cDot11ConfigureAPID
OBJECT-TYPE
Represents which AP is configured.
1.3.6.1.4.1.2011.10.2.75.4.9.1.4H3cDot11ObjectIDTypeaccessible-for-notifycurrent
h3cDot11ConfigureRadioID
OBJECT-TYPE
Represents which radio in AP is configured.
1.3.6.1.4.1.2011.10.2.75.4.9.1.5H3cDot11RadioScopeTypeaccessible-for-notifycurrent

Notifications

NameOIDStatus
h3cDot11CfgCipherChange
NOTIFICATION-TYPE
This notification is sent when cipher type of corresponding service template is changed.
1.3.6.1.4.1.2011.10.2.75.4.9.0.1current
h3cDot11CfgPSKChange
NOTIFICATION-TYPE
This notification is sent when pre-shared key of corresponding service template is changed.
1.3.6.1.4.1.2011.10.2.75.4.9.0.2current
h3cDot11SSIDWepIDConflictTrap
NOTIFICATION-TYPE
This notification will be sent when the same wep ID is configured on two service policies.
1.3.6.1.4.1.2011.10.2.75.4.9.0.3current