MIBs Depot

GBNDeviceSwitch-MIB

Registered at
1.3.6.1.4.1.13464.1.2.2.1
Last updated
1900-11-02 00:00
Organization
Admin Co., Ltd.
Revisions
1900-11-02 00:00
Namespace
fs
Source file
GBNDeviceSwitch-MIB
Digest
sha256:010b817eccc770c0b647a2420153310930848f2d600bd477e74fd6b51ff09b08

Description

ADMIN Common Enterprise MIB definition.

Contact

Admin Co., Ltd. E-mail: support@admin.com

Imports

FromSymbols
ADMIN-MASTER-MIBgbnDevice
Q-BRIDGE-MIBPortList, VlanIndex, dot1qStaticMulticastEntry
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIInteger32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso
SNMPv2-TCDateAndTime, DisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

ADMIN-MASTER-MIB
BRIDGE-MIB
GBNDeviceSwitch-MIB
IANAifType-MIB
IF-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB

Textual conventions

NameOIDSyntaxAccessStatus
MirrorMacType
TEXTUAL-CONVENTION
nulldestinationsource
current

Objects

NameOIDSyntaxAccessStatus
gbnDeviceSwitchMirror
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.1
mirroringPort
OBJECT-TYPE
This port which all packets send to.
1.3.6.1.4.1.13464.1.2.2.1.1.1INTEGER (0..26)read-writecurrent
mirroredEgrPort
OBJECT-TYPE
The egress ports which need to monitor.
1.3.6.1.4.1.13464.1.2.2.1.1.2PortListread-writecurrent
mirroredIgrPort
OBJECT-TYPE
The ingress ports which need to monitor.
1.3.6.1.4.1.13464.1.2.2.1.1.3PortListread-writecurrent
ingressMirrorMac
OBJECT-TYPE
The MAC address which will be compared with the ingress frame, Only the matched frame will be mirrored
1.3.6.1.4.1.13464.1.2.2.1.1.4MacAddressread-writecurrent
egressMirrorMac
OBJECT-TYPE
The MAC address which will be compared with the egress frame, Only the matched frame will be mirrored
1.3.6.1.4.1.13464.1.2.2.1.1.5MacAddressread-writecurrent
ingressMirrorMacType
OBJECT-TYPE
The destination or source MAC address which will be compared with the ingress frame
1.3.6.1.4.1.13464.1.2.2.1.1.6MirrorMacTyperead-writecurrent
egressMirrorMacType
OBJECT-TYPE
The destination or source MAC address which will be compared with the egress frame
1.3.6.1.4.1.13464.1.2.2.1.1.7MirrorMacTyperead-writecurrent
ingressMirrorDivider
OBJECT-TYPE
the mirror sampling divider
1.3.6.1.4.1.13464.1.2.2.1.1.8INTEGER (0..1023)read-writecurrent
egressMirrorDivider
OBJECT-TYPE
the mirror sampling divider
1.3.6.1.4.1.13464.1.2.2.1.1.9INTEGER (0..1023)read-writecurrent
gbnDeviceSwitchPort
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.2
portTypeTable
OBJECT-TYPE
A table of switch interfaces and associated properties.
1.3.6.1.4.1.13464.1.2.2.1.2.1not-accessiblecurrent
portTypeEntry
OBJECT-TYPE
Table entry for switch interface control and status information.
1.3.6.1.4.1.13464.1.2.2.1.2.1.1not-accessiblecurrent
portNumber
OBJECT-TYPE
the index of port.
1.3.6.1.4.1.13464.1.2.2.1.2.1.1.1INTEGERread-onlycurrent
portType
OBJECT-TYPE
:1210/100M3100M 4100M51000M61000M 71000M; 8CPU;910000M
1.3.6.1.4.1.13464.1.2.2.1.2.1.1.2INTEGER {blank(1), FE(2), single100FX(3), double100FX(4), single1000FX(5), double1000FX(6), fE1000(7), cpu(8), FX10000(9)}read-onlycurrent
gbnDeviceSwitchAggregation
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.3
aggTable
OBJECT-TYPE
A table that contains information about every Aggregator that is associated with this System.
1.3.6.1.4.1.13464.1.2.2.1.3.1not-accessibleobsolete
aggEntry
OBJECT-TYPE
A list of the Aggregator parameters. This is indexed by the ifIndex of the Aggregator.
1.3.6.1.4.1.13464.1.2.2.1.3.1.1not-accessibleobsolete
aggUnit
OBJECT-TYPE
The Interface Unit of the Aggregation.
1.3.6.1.4.1.13464.1.2.2.1.3.1.1.1INTEGERread-onlyobsolete
aggPort
OBJECT-TYPE
The MasterPort of the Aggregation.
1.3.6.1.4.1.13464.1.2.2.1.3.1.1.2INTEGERread-onlyobsolete
aggPortListPorts
OBJECT-TYPE
The complete set of ports currently associated with this Aggregator. Each bit set in this list represents an Actor Port member of this Link Aggregation.
1.3.6.1.4.1.13464.1.2.2.1.3.1.1.3PortListread-writeobsolete
aggRule
OBJECT-TYPE
The Rule to be applied to this Link Aggregator's Trunk Group Table. The rules are based on the following selections SrcMAC (1), means that the last three bits of the Source MAC Address are used to index the Trunk Group to get the destination port. DestMAC (2), means the last three bits of the Destination MAC Address are used to index into the Trunk Group to get the destination port. SrcXORDestMAC (3), means that the last three bits of the Source MAC Address are logically XORed with the last three bits of the Destination MAC Address and used to index into the Trunk Group to get the destination port. SrcIP (4), means the last three bits of the Source IP Address are used to index into the Trunk Group to get the destination port. DestIP (5), means the last three bits of the Destination IP Address are used to index into the Trunk Group to get the destination port. SrcXORDestIP (6), means the last three bits of the Source IP Address are logically XORed with the last three bits of the Destination IP Address and used to index into the Trunk Group to get the destination port. This rule defines the distribution algorithm applied to the aggregated link.
1.3.6.1.4.1.13464.1.2.2.1.3.1.1.4INTEGER {srcMAC(1), destMAC(2), srcXORDestMAC(3), srcIP(4), destIP(5), srcXORDestIP(6)}read-writeobsolete
aggRowstatus
OBJECT-TYPE
rowstatus of trunk.
1.3.6.1.4.1.13464.1.2.2.1.3.1.1.5TruthValueread-writeobsolete
gbnDeviceSwitchL3
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.4
l3Table
OBJECT-TYPE
L3
1.3.6.1.4.1.13464.1.2.2.1.4.1not-accessiblecurrent
l3Entry
OBJECT-TYPE
L3
1.3.6.1.4.1.13464.1.2.2.1.4.1.1not-accessiblecurrent
l3IpAddress
OBJECT-TYPE
IP
1.3.6.1.4.1.13464.1.2.2.1.4.1.1.1IpAddressread-onlycurrent
l3NextHopMacAddress
OBJECT-TYPE
IPMAC
1.3.6.1.4.1.13464.1.2.2.1.4.1.1.2MacAddressread-onlycurrent
l3Vlan
OBJECT-TYPE
IPVLAN
1.3.6.1.4.1.13464.1.2.2.1.4.1.1.3VlanIndexread-onlycurrent
l3Port
OBJECT-TYPE
1.3.6.1.4.1.13464.1.2.2.1.4.1.1.4INTEGERread-onlycurrent
l3CreateTime
OBJECT-TYPE
Create Time,such as 2004-07-29,13:30:15.0
1.3.6.1.4.1.13464.1.2.2.1.4.1.1.5DateAndTimeread-onlycurrent
l3UpdateTime
OBJECT-TYPE
Update Time,such as 2004-07-29,13:30:15.0
1.3.6.1.4.1.13464.1.2.2.1.4.1.1.6DateAndTimeread-onlycurrent
gbnDeviceSwitchLoopTest
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.5
loopTestPortno
OBJECT-TYPE
port bitmap:Numbers of the port to be tested. The highest bit is port 1, the second bit is port 2, and so on.
1.3.6.1.4.1.13464.1.2.2.1.5.1PortListread-writecurrent
loopTestType
OBJECT-TYPE
DURABLE: { 4 } Setting this object to 2-4 enables loop back test. Setting it to 1 disables loop back test.
1.3.6.1.4.1.13464.1.2.2.1.5.2INTEGER {noop(1), local(2), remote(3), other(4)}read-writecurrent
loopTestSuccess
OBJECT-TYPE
if the highest bit is 0:the port 1 loop fail, 1,the port 1 loop success, and so on.
1.3.6.1.4.1.13464.1.2.2.1.5.3PortListread-onlycurrent
gbnDeviceSwitchSRM
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.6
srmHardwareEnable
OBJECT-TYPE
Add network routes to hardware table or not.Default is enable.
1.3.6.1.4.1.13464.1.2.2.1.6.1INTEGER {enabled(1), disabled(2)}read-writecurrent
srmHardwareDEFCPU
OBJECT-TYPE
The DEF routes goes to CPU.
1.3.6.1.4.1.13464.1.2.2.1.6.2INTEGER {enabled(1), disabled(2)}read-writecurrent
gbnDeviceSwitchFlowAlarm
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.7
portFlowAlarmTable
OBJECT-TYPE
A Table of port flow alarm.
1.3.6.1.4.1.13464.1.2.2.1.7.1not-accessiblecurrent
portFlowAlarmEntry
OBJECT-TYPE
A list of port flow alarm.
1.3.6.1.4.1.13464.1.2.2.1.7.1.1not-accessiblecurrent
portFlowAlarmPort
OBJECT-TYPE
The port number.
1.3.6.1.4.1.13464.1.2.2.1.7.1.1.1Integer32read-onlycurrent
portFlowAlarmEnable
OBJECT-TYPE
The enable status of the port flow alarm
1.3.6.1.4.1.13464.1.2.2.1.7.1.1.2TruthValueread-writecurrent
portFlowAlarmExceedStatus
OBJECT-TYPE
The exceed status of the port flow alarm
1.3.6.1.4.1.13464.1.2.2.1.7.1.1.3TruthValueread-onlycurrent
portFlowAlarmExceedThreshold
OBJECT-TYPE
The exceed threshold of port flow alarm.
1.3.6.1.4.1.13464.1.2.2.1.7.1.1.4Integer32read-writecurrent
portFlowAlarmNormalThreshold
OBJECT-TYPE
The normal threshold of port flow alarm.
1.3.6.1.4.1.13464.1.2.2.1.7.1.1.5Integer32read-writecurrent
portFlowAlarmGlobalEnable
OBJECT-TYPE
The global enable status of port flow alarm.
1.3.6.1.4.1.13464.1.2.2.1.7.2TruthValueread-writecurrent
portFlowAlarmTrap
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.7.5
gbnDeviceSwitchQueneScheduer
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.8
qosQueueSchedulerGroup
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.8.1
qosWrrQueue1Weight
OBJECT-TYPE
Weight of 1th queue(%). for 3650, the range is 1 to 255, for 3750-24/48,the range is 1 to 15.
1.3.6.1.4.1.13464.1.2.2.1.8.1.1INTEGERread-writecurrent
qosWrrQueue2Weight
OBJECT-TYPE
Weight of 2th queue(%). for 3650, the range is 0 to 255, for 3750-24/48,the range is 1 to 15.
1.3.6.1.4.1.13464.1.2.2.1.8.1.2INTEGERread-writecurrent
qosWrrQueue3Weight
OBJECT-TYPE
Weight of 3th queue(%). for 3650, the range is 0 to 255, for 3750-24/48,the range is 1 to 15.
1.3.6.1.4.1.13464.1.2.2.1.8.1.3INTEGERread-writecurrent
qosWrrQueue4Weight
OBJECT-TYPE
Weight of 4th queue(%). for 3650, the range is 0 to 255, for 3750-24/48,the range is 1 to 15.
1.3.6.1.4.1.13464.1.2.2.1.8.1.4INTEGERread-writecurrent
qosWrrMaxDelayValue
OBJECT-TYPE
the maximum allowable latency for packet transmission on the priorest COS
1.3.6.1.4.1.13464.1.2.2.1.8.1.5INTEGER (1..255)read-writecurrent
qosQueueSchedulerMode
OBJECT-TYPE
queue scheduler mode: strict priority, weighted round robin, strict priority+weighted round robin
1.3.6.1.4.1.13464.1.2.2.1.8.1.6INTEGER {strictPriority(1), wrr(2), sp-wrr(3)}read-writecurrent
qosWrrQueue5Weight
OBJECT-TYPE
Weight of 5th queue(%). for 3650, the range is 0 to 255, for 3750-24/48,the range is 1 to 15.
1.3.6.1.4.1.13464.1.2.2.1.8.1.7INTEGERread-writecurrent
qosWrrQueue6Weight
OBJECT-TYPE
Weight of 6th queue(%). for 3650, the range is 0 to 255, for 3750-24/48,the range is 1 to 15.
1.3.6.1.4.1.13464.1.2.2.1.8.1.8INTEGERread-writecurrent
qosWrrQueue7Weight
OBJECT-TYPE
Weight of 7th queue(%). for 3650, the range is 0 to 255, for 3750-24/48,the range is 1 to 15.
1.3.6.1.4.1.13464.1.2.2.1.8.1.9INTEGERread-writecurrent
qosWrrQueue8Weight
OBJECT-TYPE
Weight of 8th queue(%). for 3650, the range is 0 to 255, for 3750-24/48,the range is 1 to 15.
1.3.6.1.4.1.13464.1.2.2.1.8.1.10INTEGERread-writecurrent
gbnDeviceSwitchLineRate
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.9
qosLineRateTable
OBJECT-TYPE
A list of line-rate QOS entries.
1.3.6.1.4.1.13464.1.2.2.1.9.1not-accessiblecurrent
qosLineRateEntry
OBJECT-TYPE
A list of line-rate QOS entries.
1.3.6.1.4.1.13464.1.2.2.1.9.1.1not-accessiblecurrent
qosLineRateInterface
OBJECT-TYPE
the line rate interface.
1.3.6.1.4.1.13464.1.2.2.1.9.1.1.1INTEGER (1..26)read-onlycurrent
qosLineRateTargetRate
OBJECT-TYPE
The target rate(Kbps) of the line-rate QOS. Must be a multiple of 64Kbps
1.3.6.1.4.1.13464.1.2.2.1.9.1.1.2INTEGER (64..1000000)read-writecurrent
qosLineRateTargetBurst
OBJECT-TYPE
The target burst(Kbps) of the line-rate QOS. Must be a multiple of 64Kbps
1.3.6.1.4.1.13464.1.2.2.1.9.1.1.3INTEGER (64..1000000)read-writecurrent
qosLineRateTargetRateIngress
OBJECT-TYPE
The ingress target rate(Kbps) of the line-rate QOS.0 means disable
1.3.6.1.4.1.13464.1.2.2.1.9.1.1.4INTEGER (0..1024000)read-writecurrent
gbnDeviceSwitchPortIsolation
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.10
portIsolationGroup
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.10.1
portIsolationDownLinkPorts
OBJECT-TYPE
port isolation down link portlist
1.3.6.1.4.1.13464.1.2.2.1.10.1.1PortListread-writecurrent
portIsolationUpLinkTable
OBJECT-TYPE
A list of uplink-ports of portisolation entries. conflict with portIsolationDownLinkPorts.
1.3.6.1.4.1.13464.1.2.2.1.10.1.2not-accessiblecurrent
portIsolationUpLinkEntry
OBJECT-TYPE
A list of uplink-ports of portisolation entries.
1.3.6.1.4.1.13464.1.2.2.1.10.1.2.1not-accessiblecurrent
portisolationInterface
OBJECT-TYPE
port index, start from 1.
1.3.6.1.4.1.13464.1.2.2.1.10.1.2.1.1INTEGERread-onlycurrent
gbnDeviceSwitchStormControl
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.11
stormControlTable
OBJECT-TYPE
A list of storm control entries.
1.3.6.1.4.1.13464.1.2.2.1.11.1not-accessiblecurrent
stormControlEntry
OBJECT-TYPE
A list of storm control entries.
1.3.6.1.4.1.13464.1.2.2.1.11.1.1not-accessiblecurrent
stormControlInterface
OBJECT-TYPE
the storm control interface.
1.3.6.1.4.1.13464.1.2.2.1.11.1.1.1INTEGERread-onlycurrent
stormControlType
OBJECT-TYPE
the pack flow type of the storm control.
1.3.6.1.4.1.13464.1.2.2.1.11.1.1.2INTEGERread-onlycurrent
stormControlTargetRate
OBJECT-TYPE
the target rate of the storm control.
1.3.6.1.4.1.13464.1.2.2.1.11.1.1.3INTEGER (1..1000)read-writecurrent
stormControlRowStatus
OBJECT-TYPE
row status of the storm control
1.3.6.1.4.1.13464.1.2.2.1.11.1.1.4RowStatusread-writecurrent
stormControlMode
OBJECT-TYPE
the mode of the storm control.
1.3.6.1.4.1.13464.1.2.2.1.11.1.1.5INTEGER {pps(0), bps(1)}read-writecurrent
gbnDeviceSwitchAntiDos
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.12
ipfragmnetnumber
OBJECT-TYPE
The ip fragment number.
1.3.6.1.4.1.13464.1.2.2.1.12.1INTEGER (0..800)read-writecurrent
ipTTL
OBJECT-TYPE
Control IP with TTL=0 packet,default is not traffic to the CPU.
1.3.6.1.4.1.13464.1.2.2.1.12.2TruthValueread-writecurrent
gbnDeviceSwitchBandWidth
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.13
bandwidthcontrolTable
OBJECT-TYPE
A table of switch interfaces and associated properties.
1.3.6.1.4.1.13464.1.2.2.1.13.1not-accessiblecurrent
bandwidthcontrolEntry
OBJECT-TYPE
Table entry for switch interface control and status information.
1.3.6.1.4.1.13464.1.2.2.1.13.1.1not-accessiblecurrent
controlPort
OBJECT-TYPE
the index of port.
1.3.6.1.4.1.13464.1.2.2.1.13.1.1.1INTEGER (1..26)not-accessiblecurrent
portEgressBandwidthcontrol
OBJECT-TYPE
Egress Speed Value of port, bandwidth control .
1.3.6.1.4.1.13464.1.2.2.1.13.1.1.2INTEGER (0..1024000)read-writecurrent
portIngressBandwidthcontrol
OBJECT-TYPE
Ingress Speed Value of port, bandwidth control .
1.3.6.1.4.1.13464.1.2.2.1.13.1.1.3INTEGER (0..1024000)read-writecurrent
gbnDeviceSwitchHigigStatistics
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.14
higigStatisticsTable
OBJECT-TYPE
A table of Higig Statistics Info.
1.3.6.1.4.1.13464.1.2.2.1.14.1not-accessiblecurrent
higigStatisticsEntry
OBJECT-TYPE
Table entry for Higig Statistics information.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1not-accessiblecurrent
unit
OBJECT-TYPE
unit number.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.1INTEGER (0..1)not-accessiblecurrent
higig
OBJECT-TYPE
higig number.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.2INTEGER (1..2)not-accessiblecurrent
snEtherStatsPkts64Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.3Counter64read-onlycurrent
snEtherStatsPkts65to127Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.4Counter64read-onlycurrent
snEtherStatsPkts128to255Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.5Counter64read-onlycurrent
snEtherStatsPkts256to511Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.6Counter64read-onlycurrent
snEtherStatsPkts512to1023Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.7Counter64read-onlycurrent
snEtherStatsPkts1024to1518Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets).
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.8Counter64read-onlycurrent
sndot1dTpPortInFrames
OBJECT-TYPE
The number of frames that have been received by this port from its segment. Note that a frame received on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.9Counter64read-onlymandatory
snifInOctets
OBJECT-TYPE
The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.10Counter64read-onlycurrent
snifInDiscards
OBJECT-TYPE
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.11Counter64read-onlycurrent
snifInUcastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.12Counter64read-onlycurrent
snifInMulticastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.13Counter64read-onlycurrent
snifInBroadcastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.14Counter64read-onlycurrent
snifInErrors
OBJECT-TYPE
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.15Counter64read-onlycurrent
snDot3StatsFCSErrors
OBJECT-TYPE
A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.16Counter64read-onlycurrent
snDot3StatsSymbolErrors
OBJECT-TYPE
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present. For an interface operating in half-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than slotTime, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' or 'carrier extend error' on the GMII. For an interface operating in full-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle a carrier event) for a period of time equal to or greater than minFrameSize, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' on the GMII. The count represented by an instance of this object is incremented at most once per carrier event, even if multiple symbol errors occur during the carrier event. This count does not increment if a collision is present. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.17Counter64read-onlycurrent
snDot3StatsCarrierSenseErrors
OBJECT-TYPE
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.18Counter64read-onlycurrent
snEtherStatsUndersizePkts
OBJECT-TYPE
The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.19Counter64read-onlycurrent
snEtherStatsOversizePkts
OBJECT-TYPE
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.20Counter64read-onlycurrent
snEtherStatsFragments
OBJECT-TYPE
The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that it is entirely normal for etherStatsFragments to increment. This is because it counts both runts (which are normal occurrences due to collisions) and noise hits.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.21Counter64read-onlycurrent
snEtherStatsJabbers
OBJECT-TYPE
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that this definition of jabber is different than the definition in IEEE-802.3 section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.22Counter64read-onlycurrent
sndot1dTpPortOutFrames
OBJECT-TYPE
The number of frames that have been transmitted by this port to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.23Counter64read-onlymandatory
snifOutOctets
OBJECT-TYPE
The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.24Counter64read-onlycurrent
snifOutDiscards
OBJECT-TYPE
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.25Counter64read-onlycurrent
snifOutUcastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.26Counter64read-onlycurrent
snifOutMulticastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.27Counter64read-onlycurrent
snifOutBroadcastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.28Counter64read-onlycurrent
snifOutErrors
OBJECT-TYPE
For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.29Counter64read-onlycurrent
snDot3StatsDeferredTransmissions
OBJECT-TYPE
A count of frames for which the first transmission attempt on a particular interface is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.30Counter64read-onlycurrent
snEtherStatsCollisions
OBJECT-TYPE
The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment would. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.31Counter64read-onlycurrent
snDot3StatsLateCollisions
OBJECT-TYPE
The number of times that a collision is detected on a particular interface later than 512 bit-times into the transmission of a packet. Five hundred and twelve bit-times corresponds to 51.2 microseconds on a 10 Mbit/s system. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics.
1.3.6.1.4.1.13464.1.2.2.1.14.1.1.32Counter64read-onlycurrent
gbnDeviceSwitchChannelStats
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.15
channelStatsTable
OBJECT-TYPE
A table of Channel group Statistics Info(32).
1.3.6.1.4.1.13464.1.2.2.1.15.1not-accessiblecurrent
channelStatsEntry
OBJECT-TYPE
Table entry for Channel Statistics information(32).
1.3.6.1.4.1.13464.1.2.2.1.15.1.1not-accessiblecurrent
channelGroupIndex
OBJECT-TYPE
The configed channel-group index list.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.1INTEGERread-onlycurrent
channelInOctetRate
OBJECT-TYPE
The ingress octet rate of this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.2Counter32read-onlycurrent
channelInFrameRate
OBJECT-TYPE
The ingress packet rate of this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.3Counter32read-onlycurrent
channelOutOctetRate
OBJECT-TYPE
The egress octet rate of this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.4Counter32read-onlycurrent
channelOutFrameRate
OBJECT-TYPE
The egress packet rate of this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.5Counter32read-onlycurrent
channelPkts64Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets) in this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.6Counter32read-onlycurrent
channelPkts65to127Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets) in this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.7Counter32read-onlycurrent
channelPkts128to255Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets). in this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.8Counter32read-onlycurrent
channelPkts256to511Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets) in this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.9Counter32read-onlycurrent
channelPkts512to1023Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets) in this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.10Counter32read-onlycurrent
channelPkts1024to1518Octets
OBJECT-TYPE
The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets) in this channel-group.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.11Counter32read-onlycurrent
channelInFrames
OBJECT-TYPE
The number of frames that have been received by this channel-group from its segment. Note that a frame received on the interface corresponding to this channel-group is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.12Counter32read-onlymandatory
channelInOctets
OBJECT-TYPE
The total number of octets received on the channel-group, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.13Counter32read-onlycurrent
channelInDiscards
OBJECT-TYPE
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.14Counter32read-onlycurrent
channelInUcastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.15Counter32read-onlycurrent
channelInMulticastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.16Counter32read-onlycurrent
channelInBroadcastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.17Counter32read-onlycurrent
channelInErrors
OBJECT-TYPE
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.18Counter32read-onlycurrent
channelFCSErrors
OBJECT-TYPE
A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.19Counter32read-onlycurrent
channelSymbolErrors
OBJECT-TYPE
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present. For an interface operating in half-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than slotTime, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' or 'carrier extend error' on the GMII. For an interface operating in full-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle a carrier event) for a period of time equal to or greater than minFrameSize, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' on the GMII. The count represented by an instance of this object is incremented at most once per carrier event, even if multiple symbol errors occur during the carrier event. This count does not increment if a collision is present. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.20Counter32read-onlycurrent
channelCarrierSenseErrors
OBJECT-TYPE
The number of times that the carrier sense condition was lost or never asserted when attempting to transmit a frame on a particular interface. The count represented by an instance of this object is incremented at most once per transmission attempt, even if the carrier sense condition fluctuates during a transmission attempt.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.21Counter32read-onlycurrent
channelUndersizePkts
OBJECT-TYPE
The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.22Counter32read-onlycurrent
channelOversizePkts
OBJECT-TYPE
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.23Counter32read-onlycurrent
channelFragments
OBJECT-TYPE
The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that it is entirely normal for etherStatsFragments to increment. This is because it counts both runts (which are normal occurrences due to collisions) and noise hits.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.24Counter32read-onlycurrent
channelJabbers
OBJECT-TYPE
The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that this definition of jabber is different than the definition in IEEE-802.3 section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.25Counter32read-onlycurrent
channelOutFrames
OBJECT-TYPE
The number of frames that have been transmitted by this channel-group to its segment. Note that a frame transmitted on the interface corresponding to this port is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.26Counter32read-onlymandatory
channelOutOctets
OBJECT-TYPE
The total number of octets transmitted out of the channel-group, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.27Counter32read-onlycurrent
channelOutDiscards
OBJECT-TYPE
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.28Counter32read-onlycurrent
channelOutUcastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.29Counter32read-onlycurrent
channelOutMulticastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.30Counter32read-onlycurrent
channelOutBroadcastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.31Counter32read-onlycurrent
channelOutErrors
OBJECT-TYPE
For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.32Counter32read-onlycurrent
channelDeferredTransmissions
OBJECT-TYPE
A count of frames for which the first transmission attempt on a particular interface is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.33Counter32read-onlycurrent
channelCollisions
OBJECT-TYPE
The best estimate of the total number of collisions on this Ethernet segment. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment would. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.34Counter32read-onlycurrent
channelLateCollisions
OBJECT-TYPE
The number of times that a collision is detected on a particular interface later than 512 bit-times into the transmission of a packet. Five hundred and twelve bit-times corresponds to 51.2 microseconds on a 10 Mbit/s system. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics.
1.3.6.1.4.1.13464.1.2.2.1.15.1.1.35Counter32read-onlycurrent
channelStatsXTable
OBJECT-TYPE
A table of Channel group Statistics Info(64).
1.3.6.1.4.1.13464.1.2.2.1.15.2not-accessiblecurrent
channelStatsXEntry
OBJECT-TYPE
Table entry for Channel Statistics information(64).
1.3.6.1.4.1.13464.1.2.2.1.15.2.1not-accessiblecurrent
channelHCInFrames
OBJECT-TYPE
The number of frames that have been received by this channel-group from its segment. Note that a frame received on the interface corresponding to this channel-group is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames. This object is a 64-bit version of channelInFrames.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.1Counter64read-onlycurrent
channelHCInOctets
OBJECT-TYPE
The total number of octets received on the channel-group, including framing characters. This object is a 64-bit version of channelInOctets. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.2Counter64read-onlycurrent
channelHCInUcastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. This object is a 64-bit version of channelInUcastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.3Counter64read-onlycurrent
channelHCInMulticastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. This object is a 64-bit version of channelInMulticastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.4Counter64read-onlycurrent
channelHCInBroadcastPkts
OBJECT-TYPE
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. This object is a 64-bit version of channelInBroadcastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.5Counter64read-onlycurrent
channelHCInDiscards
OBJECT-TYPE
Count of valid frames that have been received by this channel-group from its segment which were discarded (i.e., filtered) by the Forwarding Process.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.6Counter64read-onlycurrent
channelHCOutFrames
OBJECT-TYPE
The number of frames that have been transmitted by this channel-group to its segment. Note that a frame transmitted on the interface corresponding to this channel-group is only counted by this object if and only if it is for a protocol being processed by the local bridging function, including bridge management frames. This object is a 64-bit version of channelOutFrames.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.7Counter64read-onlycurrent
channelHCOutOctets
OBJECT-TYPE
The total number of octets transmitted out of the channel-group, including framing characters. This object is a 64-bit version of channelOutOctets. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.8Counter64read-onlycurrent
channelHCOutUcastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. This object is a 64-bit version of channelOutUcastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.9Counter64read-onlycurrent
channelHCOutMulticastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. This object is a 64-bit version of channelOutMulticastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.10Counter64read-onlycurrent
channelHCOutBroadcastPkts
OBJECT-TYPE
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. This object is a 64-bit version of channelOutBroadcastPkts. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
1.3.6.1.4.1.13464.1.2.2.1.15.2.1.11Counter64read-onlycurrent
gbnDeviceSwitchRmoteMirror
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.16
remoteMirrorVlanTable
OBJECT-TYPE
A table of switch interfaces and associated properties.
1.3.6.1.4.1.13464.1.2.2.1.16.1not-accessiblecurrent
remoteMirrorVlanEntry
OBJECT-TYPE
Table entry for switch interface control and status information.
1.3.6.1.4.1.13464.1.2.2.1.16.1.1not-accessiblecurrent
remoteMirrorVlanIndex
OBJECT-TYPE
the index of remote mirror vlan.
1.3.6.1.4.1.13464.1.2.2.1.16.1.1.1INTEGER (2..4094)read-onlycurrent
remoteMirrorVlanEnable
OBJECT-TYPE
1:enable. 2 disable
1.3.6.1.4.1.13464.1.2.2.1.16.1.1.2TruthValueread-writecurrent
remoteMirrorRspanVlanSet
OBJECT-TYPE
set rspan vlan on src-switch, 0:means no rspan vlan;don't set vlan 1 to be rspan vlan
1.3.6.1.4.1.13464.1.2.2.1.16.2INTEGER (0..4094)read-writecurrent
remoteMirrorEnable
OBJECT-TYPE
enable remote mirror on src-switch
1.3.6.1.4.1.13464.1.2.2.1.16.3TruthValueread-writecurrent
gbnDeviceSwitchPortSFPInfo
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.17
portSFPInfoTable
OBJECT-TYPE
A table of switch interfaces and associated properties.
1.3.6.1.4.1.13464.1.2.2.1.17.1not-accessiblecurrent
portSFPInfoEntry
OBJECT-TYPE
Table entry for switch interface control and status information.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1not-accessiblecurrent
portSFPNumber
OBJECT-TYPE
The index of port.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.1INTEGERread-onlycurrent
transceiverType
OBJECT-TYPE
Transceiver type
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.2INTEGER {SFPNotExist(0), GBIC(1), SFF(2), SFP(3), XBI(4), Xenpak(5), XFP(6), XFF(7), XFP-E(8), XPak(9), X2(10), DWDM-SFP(11), QSFP(12), Unknown(99)}read-onlycurrent
compliance
OBJECT-TYPE
Compliance type
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.3DisplayStringread-onlycurrent
connectorType
OBJECT-TYPE
Connector type
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.4INTEGER {SFPNotExist(0), SC(1), FibreChannelStyle1CopperConnector(2), FibreChannelStyle2CopperConnector(3), BNCTNC(4), FibreChannelCoaxialHeaders(5), FiberJack(6), LC(7), MT-RJ(8), MU(9), SG(10), OpticalPigtail(11), MPOParallelOptic(12), HSSDCII(32), CopperPigtail(33), RJ45(34), Electrical-Mode(35), Unknown(99)}read-onlycurrent
waveLength
OBJECT-TYPE
Wave length.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.5INTEGERread-onlycurrent
transferDistance
OBJECT-TYPE
Transfer distance.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.6INTEGERread-onlycurrent
digitalDiagnosticMonitor
OBJECT-TYPE
Digital Diagnostic Monitor.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.7INTEGER {SFPNotExist(0), NotSupported(1), Supported(2)}read-onlycurrent
vendorName
OBJECT-TYPE
Vendor Name.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.8DisplayStringread-onlycurrent
manuSerialNumber
OBJECT-TYPE
Manufacture Serial Number.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.9DisplayStringread-onlycurrent
manufacturingDate
OBJECT-TYPE
Manufacturing Date.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.10DisplayStringread-onlycurrent
temperature
OBJECT-TYPE
Temperature of sfp.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.11INTEGERread-onlycurrent
voltage
OBJECT-TYPE
Voltage of sfp.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.12DisplayStringread-onlycurrent
biasCurrent
OBJECT-TYPE
bias Current.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.13DisplayStringread-onlycurrent
biasHighThreshold
OBJECT-TYPE
bias Current High Threshold.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.14DisplayStringread-onlycurrent
biasLowThreshold
OBJECT-TYPE
bias Current Low Threshold.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.15DisplayStringread-onlycurrent
rxPower
OBJECT-TYPE
RX Power.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.16DisplayStringread-onlycurrent
rxPowerHighThreshold
OBJECT-TYPE
RX Power High Threshold.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.17DisplayStringread-onlycurrent
rxPowerLowThreshold
OBJECT-TYPE
RX Power Low Threshold.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.18DisplayStringread-onlycurrent
txPower
OBJECT-TYPE
TX Power.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.19DisplayStringread-onlycurrent
txPowerHighThreshold
OBJECT-TYPE
TX Power High Threshold.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.20DisplayStringread-onlycurrent
txPowerLowThreshold
OBJECT-TYPE
TX Power Low Threshold.
1.3.6.1.4.1.13464.1.2.2.1.17.1.1.21DisplayStringread-onlycurrent
gbnDeviceSwitchPortAvgRate
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.18
portRateStatisticsInterval
OBJECT-TYPE
port average rate statistics time interval, unit is minute, default is 5 minutes.
1.3.6.1.4.1.13464.1.2.2.1.18.1Integer32 (1..5)read-writecurrent
portAvgRateTable
OBJECT-TYPE
A table of port average rate statistics info(32).
1.3.6.1.4.1.13464.1.2.2.1.18.2not-accessiblecurrent
portAvgRateEntry
OBJECT-TYPE
Table entry for port average rate statistics information(32).
1.3.6.1.4.1.13464.1.2.2.1.18.2.1not-accessiblecurrent
portIndex
OBJECT-TYPE
The port index list.
1.3.6.1.4.1.13464.1.2.2.1.18.2.1.1INTEGERread-onlycurrent
portInOctetRate
OBJECT-TYPE
The ingress octet rate of this port.
1.3.6.1.4.1.13464.1.2.2.1.18.2.1.2Counter32read-onlycurrent
portInFrameRate
OBJECT-TYPE
The ingress packet rate of this port.
1.3.6.1.4.1.13464.1.2.2.1.18.2.1.3Counter32read-onlycurrent
portOutOctetRate
OBJECT-TYPE
The egress octet rate of this port.
1.3.6.1.4.1.13464.1.2.2.1.18.2.1.4Counter32read-onlycurrent
portOutFrameRate
OBJECT-TYPE
The egress packet rate of this port.
1.3.6.1.4.1.13464.1.2.2.1.18.2.1.5Counter32read-onlycurrent
gbnDeviceSwitchPortbandwidthUtilization
OBJECT-IDENTITY
1.3.6.1.4.1.13464.1.2.2.1.19
portBandwidthUtilizationEnable
OBJECT-TYPE
The port bandwidth switch.
1.3.6.1.4.1.13464.1.2.2.1.19.1TruthValue {enable(1), disable(2)}read-writecurrent
portBandwidthUtilizationTable
OBJECT-TYPE
A table of port bandwidth utilization info(32).
1.3.6.1.4.1.13464.1.2.2.1.19.2not-accessiblecurrent
portBandwidthUtilizationEntry
OBJECT-TYPE
Table entry for port bandwidth utilization information(32).
1.3.6.1.4.1.13464.1.2.2.1.19.2.2not-accessiblecurrent
portBandIndex
OBJECT-TYPE
The port index list.
1.3.6.1.4.1.13464.1.2.2.1.19.2.2.1INTEGERread-onlycurrent
portInBandwidthUtilization
OBJECT-TYPE
The ingress bandwidth utilization of this port.
1.3.6.1.4.1.13464.1.2.2.1.19.2.2.2Counter32read-onlycurrent
portOutBandwidthUtilization
OBJECT-TYPE
The egress bandwidth utilization of this port.
1.3.6.1.4.1.13464.1.2.2.1.19.2.2.3Counter32read-onlycurrent

Notifications

NameOIDStatus
portFlowAlarmExceedTrap
NOTIFICATION-TYPE
Port ingress packet rate become too big, port flow exceed alarm happen.
1.3.6.1.4.1.13464.1.2.2.1.7.5.1current
portFlowAlarmNormalTrap
NOTIFICATION-TYPE
Port ingress packet rate become normal, port flow normal alarm happen.
1.3.6.1.4.1.13464.1.2.2.1.7.5.2current