EdgeSwitch-SWITCHING-MIB

TEXTUAL-CONVENTION

This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.

TEXTUAL-CONVENTION

This data type is used to model IPv6 address interface identifiers. This is a binary string of up to 8 octets in network byte-order.

TEXTUAL-CONVENTION

This data type is used to model IPv6 address prefixes. This is a binary string of up to 16 octets in network byte-order.

TEXTUAL-CONVENTION

A unique value, greater than zero for each internetwork-layer interface in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each internetwork-layer interface must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization.

TEXTUAL-CONVENTION

This textual convention is an extension of the Ipv6IfIndex convention. The latter defines a greater than zero value used to identify an IPv6 interface in the managed system. This extension permits the additional value of zero. The value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced.

TEXTUAL-CONVENTION

This data type is used to model port ids. This is a binary string of 2 octets.

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight vlans, with the first octet specifying vlans 1 through 8, the second octet specifying vlans 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered vlan, and the least significant bit represents the highest numbered vlan. Thus, each vlan supported is represented by a single bit within the value of this object. If that bit has a value of '1' then the associated port is in that vlan; the port is not included if the vlans bit has a value of '0'.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The switch's Inventory system description.

OBJECT-TYPE

Type of the Machine used in the Switch

OBJECT-TYPE

The switch's Machine Model.

OBJECT-TYPE

Serial number of the switch.

OBJECT-TYPE

FRU Number of the switch

OBJECT-TYPE

The switch's Inventory Maintenance Level

OBJECT-TYPE

The switch's Inventory Part Number

OBJECT-TYPE

Name of the Manufacturer of this unit

OBJECT-TYPE

Burned-In MAC Address

OBJECT-TYPE

Operating System running on this unit

OBJECT-TYPE

Network Processing Device for this unit

OBJECT-TYPE

Lists additional functional packages available on this unit.

OBJECT-TYPE

Lists the version of software loaded on this unit.

OBJECT-TYPE

Lists the version of hardware of this unit. This is a platform dependant string.

OBJECT-IDENTITY

OBJECT-TYPE

The total number of traps sent since last reset.

OBJECT-TYPE

The number of traps sent since last viewed.

OBJECT-TYPE

Agent Trap Log

OBJECT-TYPE

Agent trap log entry

OBJECT-TYPE

Unique index of trap entry

OBJECT-TYPE

System uptime when trap was sent. This entry shows how long the system has been up when the trap occurred.

OBJECT-TYPE

Description of the trap sent.

OBJECT-TYPE

Supported MIB table

OBJECT-TYPE

Supported MIB entry

OBJECT-TYPE

Unique index of the Supported MIB entry

OBJECT-TYPE

The name of the MIB (RFC or IEEE) that is supported.

OBJECT-TYPE

Description of the MIB (RFC or IEEE) that is supported.

OBJECT-IDENTITY

OBJECT-TYPE

The total memory free for utilization in KBytes.

OBJECT-TYPE

The total memory available in KBytes.

OBJECT-TYPE

The CPU Rising utilization threshold in percentage. A zero percent threshold indicates CPU Utilization Notification feature is disabled. A notification is triggered when the total CPU utilization exceeds this threshold over the configured Rising threshold interval. If the Rising threshold is configured to be less than the Falling threshold, the Falling threshold is set equal to the Rising threshold.

OBJECT-TYPE

The CPU Rising threshold interval in seconds. The time interval is configured in multiples of 5 seconds. A zero Rising interval indicates CPU Utilization Notification feature is disabled.

OBJECT-TYPE

The CPU Falling utilization threshold in percentage. Configuration of this object value is optional. Value '0' is not allowed for configuration, if the Rising threshold is non-zero. If the Falling threshold is configured to be greater than the Rising threshold, the Rising threshold is set equal to the Falling threshold. If the Falling threshold is not configured, it takes the same value as the Rising threshold. A notification is triggered when the total CPU utilization falls below this threshold over the configured Falling threshold interval.

OBJECT-TYPE

The CPU Falling threshold interval in seconds. Configuration of this object value is optional. Value '0' is not allowed for configuration, if the Rising interval is non-zero. If the Falling interval is not configured, it takes the same value as the Rising interval. The time interval is configured in multiples of 5 seconds.

OBJECT-TYPE

The CPU Free Memory threshold in kilobytes. A zero threshold value indicates the CPU Free Memory Notification feature is disabled. Notifications are triggered when the CPU Free Memory falls below the configured threshold and when it rises to 10% above the configured threshold.

OBJECT-TYPE

A table of Task and cpu utilization.

OBJECT-TYPE

Represents entry for a Task Table.

OBJECT-TYPE

Unique index of process table

OBJECT-TYPE

Name of the process

OBJECT-TYPE

CPU utilization per task in Percentage over a period of 5, 60, 300 seconds, and the Rising threshold period also in seconds, if configured.

OBJECT-TYPE

Process ID

OBJECT-TYPE

Total CPU utilization over a period of 5, 60, 300 seconds, and the Rising threshold period also in seconds, if configured.

OBJECT-IDENTITY

OBJECT-TYPE

Table lists the number of packets dropped at each CoS queue for the CPU.

OBJECT-TYPE

Packet drop statistics for a CPU CoS queue.

OBJECT-TYPE

Unique index of a CPU CoS queue.

OBJECT-TYPE

Number of packets dropped at this CPU CoS queue because the queue was full.

OBJECT-IDENTITY

OBJECT-TYPE

Number of message buffers currently available.

OBJECT-TYPE

Table lists information about message buffer allocation for packets arriving at the CPU.

OBJECT-TYPE

Information on a specific class of message buffers.

OBJECT-TYPE

Message buffer priority.

OBJECT-TYPE

Name of this class of message buffer.

OBJECT-TYPE

Number of times the system tried to allocate a message buffer allocation of this class.

OBJECT-TYPE

Number of message buffer allocation failures for this class of message buffer.

OBJECT-TYPE

Total number of message buffers in the system.

OBJECT-TYPE

Number of message buffers currently in use.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table of the switch's login session

OBJECT-TYPE

Login Session Entry

OBJECT-TYPE

Agent Login Session Index of the switch

OBJECT-TYPE

Agent Login Session UserName of the switch

OBJECT-TYPE

Agent Login Session IP Address of the switch

OBJECT-TYPE

Agent Login Session Connection Type of the switch

OBJECT-TYPE

Agent Login Session Idle Time of the switch

OBJECT-TYPE

Agent Login Session Time of the switch

OBJECT-TYPE

Status of the user. active(1) - This connection is active. destroy(6) - Set to this value to disconnect this user.

OBJECT-TYPE

Type of address agentLoginSessionInetAddress is returning. Can be either unknown(0), ipv4(1), or ipv6 (2). Will return unknown(0) in the case of a serial login.

OBJECT-TYPE

Inet Address of the connecting the user is logging in with. Will return a zero-length string in the case of a serial login.

OBJECT-IDENTITY

OBJECT-TYPE

Telnet login timeout (minutes) Config telnet timeout will set the telnet session timeout value. A session is active as long as the session has not remained idle for the value set. Specify a value from 1 to 160. Note: Changing the timeout value for active sessions does not become effective until the session is reaccessed. Any keystroke will also activate the new timeout duration.

OBJECT-TYPE

Maximum number of Telnet Sessions Config telnet maxsessions is an integer value that specifies the maximum number of telnet sessions that can be established. If the value is 0, no Telnet session can be established.

OBJECT-TYPE

Allow new telnet sessions (enable or disable) Config telnet disable means that no new Telnet sessions are to be established. Any already established session remains active until the session is ended or an abnormal network error ends it.

OBJECT-TYPE

Get/Set the TCP port number that the telnet server listens to for incoming requests. The port number is an integer value from 1 to 65535. Before setting this object, check your system (e.g. using 'netstat') to make sure the desired port number is not currently being used by any other service. The default value for this object is 23. Note that existing telnet login sessions are not affected by a change in value of this object, although establishment of any new telnet sessions must use the new port number.

OBJECT-IDENTITY

OBJECT-TYPE

Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (uncluding the '-' and '_' characters).

OBJECT-TYPE

User Config Table

OBJECT-TYPE

User Config Entry

OBJECT-TYPE

Agent User Config Index

OBJECT-TYPE

Agent User Name. This string is limited to alpha-numeric strings (including the '-' and '_' characters).

OBJECT-TYPE

Agent User Password This object will return an empty string even if a password is set.

OBJECT-TYPE

Agent User Access Mode. This object is deprecated in favor of agentUserAccessLevel.

OBJECT-TYPE

Agent User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.

OBJECT-TYPE

SNMPv3 User Authentication. The user passsword must be set to a string greater than or equal to 8 characters for this to be set to anything but none(1). none(1) - no authentication used hmacmd5(1) - Use HMAC-MD5 authentication hmacsha(1) - Use HMAC-SHA authentication

OBJECT-TYPE

SNMPv3 User Encryption Can not be set to des(2) if agentUserAuthenticationType is set to none(1). none(1) - no encryption used des(2) - DES encryption used

OBJECT-TYPE

SNMPv3 User Encryption Password This object will return an empty string even if a password is set. agentUserEncryptionType must be set to des(2) before this object can be configured. This object will return an empty string even if a password is set.

OBJECT-TYPE

Displays whether the user account is locked due to excessive failed login attempts.

OBJECT-TYPE

Date and time when the user's password expires (past or present). Only valid when password aging is enabled.

OBJECT-TYPE

Agent User Access Level. Supported values are 0, 1 and 15.

OBJECT-IDENTITY

OBJECT-TYPE

agentSerialTimeout specifies the maximum connect time(in minutes) without console activity. A value of 0 indicates that a console can be connected indefinitely. The time range is 0 to 160.

OBJECT-TYPE

agentSerialBaudrate specifies the current baud rate at which the serial port will try to connect. The available values are 1200, 2400, 4800, 9600, 19200, 38400,57600, and 115200 baud.

OBJECT-TYPE

agentSerialCharacterSize specifies the number of bits in a character. The number of bits is always 8.

OBJECT-TYPE

agentSerialHardwareFlowControl specifies whether hardware flow-control is enabled or disabled. Hardware Flow Control is always disabled.

OBJECT-TYPE

agentSerialStopBits specifies the number of Stop bits per character. The number of Stop bits is always 1.

OBJECT-TYPE

agentSerialParityType specifies the Parity Method used on the Serial Port. The Parity Method is always None.

OBJECT-IDENTITY

OBJECT-TYPE

Minimum length for user passwords All new local user passwords must be at least this many characters in length.

OBJECT-TYPE

The number of previous passwords to store for prevention of password reuse. This ensures that each user does not reuse passwords often. A value of 0 indicates that no previous passwords will be stored.

OBJECT-TYPE

The maximum time that user passwords are valid, in days, from the time the password is set. Once a password expires, the user will be required to enter a new password following the first login after password expiration. A value of 0 indicates that passwords never expire.

OBJECT-TYPE

The number of allowable failed local authentication attempts before the user's account is locked. A value of 0 indicates that user accounts will never be locked.

OBJECT-TYPE

Configures Password Strength Check feature.

OBJECT-TYPE

The number of minimum allowable uppercase letters in a password. Minimum of 0 means no restriction on that set of characters.

OBJECT-TYPE

The number of minimum allowable lowercase letters in a password. Minimum of 0 means no restriction on that set of characters.

OBJECT-TYPE

The number of minimum allowable numeric numbers in a password. Minimum of 0 means no restriction on that set of characters.

OBJECT-TYPE

The number of minimum allowable special characters in a password. Minimum of 0 means no restriction on that set of characters.

OBJECT-TYPE

The number of maximum consecutive characters can be present in a password. Maximum of 0 means disabling the restriction.

OBJECT-TYPE

The number of maximum repeated characters can be present in a password. Maximum of 0 means disabling the restriction.

OBJECT-TYPE

The number of minimum allowable character classes in a password. Minimum of 0 means no restriction on that set of characters.

OBJECT-TYPE

Retrieves the last password set Result.

OBJECT-TYPE

Represents Password strength restricted keywords from the configurable password.

OBJECT-TYPE

Represents Password strength restricted keywords from the configurable password.

OBJECT-TYPE

Specifies the given keyword string restricted from the configurable password.

OBJECT-TYPE

Create the Exclude Keyword Index and configure (Create or Destroy) the keyword to it.

OBJECT-IDENTITY

OBJECT-TYPE

Create a new user. When set with a non-empty string, a new user with that name will be created. This object will only return an empty string. This string is limited to alpha-numeric strings (including the '-' and '_' characters).

OBJECT-TYPE

A table for dot1x Client details and associated functionality.

OBJECT-TYPE

Represents entry for port config table.

OBJECT-TYPE

IAS user config index.

OBJECT-TYPE

IAS user name. This string is limited to alpha-numeric strings (including '-' and '_' characters).

OBJECT-TYPE

IAS user password.

OBJECT-TYPE

IAS User Status. active(1) - This user account is active. destroy(6) - Set to this value to remove this user account.

OBJECT-IDENTITY

OBJECT-TYPE

Banner message string. To enter the banner message in multiple lines, separate each line by '\r\n'. The maximum printable characters is limited to 2000 characters.

OBJECT-IDENTITY

OBJECT-TYPE

Agent LAG Create. When this object is set with a non-empty string, a new LAG will be created if possible, with the entered string as its name. Get operation on this MIB object returns a null-value, as for the purpose of viewing the LAG name, the user should perform the traversal of agentLagSummaryConfigTable. For this reason the get operation on this object agentLagConfigCreate becomes insignificant.

OBJECT-TYPE

A summary table of the switch's LAG config entries

OBJECT-TYPE

Switch's LAG config entry

OBJECT-TYPE

Agent LAG IfIndex. This value corresponds with the LAG interface in the ifTable.

OBJECT-TYPE

Agent LAG Name. The associated name of the LAG used during creation. Duplicate names are not allowed.

OBJECT-TYPE

Agent LAG FlushTimer.

OBJECT-TYPE

Agent LAG LinkTrap. Configures sending Link Up/Down traps when the LAG interface goes Up or Down.

OBJECT-TYPE

Agent LAG AdminMode. Administratively enables or disables this LAG interface.

OBJECT-TYPE

Agent LAG StpMode Administratively enables or disables STP on this interface.

OBJECT-TYPE

Agent LAG AddPort. Set to a non 0 value to add a port to the LAG. Values correspond to ifIndex values in the ifTable. Note: agentPortType for the port to be added must be full duplex and the same speed as previously added port(s), if any.

OBJECT-TYPE

Agent LAG DeletePort. Set to a non 0 value to remove a port from the LAG. Values correspond to ifIndex values in the ifTable.

OBJECT-TYPE

Agent LAG Status. active(1) - This LAG is enabled. destroy(6) - Set to this value to remove the LAG.

OBJECT-TYPE

Agent LAG Type. static(1) - This LAG is staticly maintained. dynamic(2) - This LAG is dynamicly maintained.

OBJECT-TYPE

Agent LAG Static Capability enable(1) - Static capability is enabled for this LAG interface disable(2) - Static capability is disabled for this LAG interface

OBJECT-TYPE

LAG Hashing Option. Valid values correspond to 1 (=Source MAC, VLAN, EtherType, and incoming port associated with the packet) 2 (=Destination MAC, VLAN, EtherType, and incoming port associated with the packet) 3 (=Source/Destination MAC, VLAN, EtherType, and incoming port associated with the packet) 4 (=Source IP and Source TCP/UDP fields of the packet) 5 (=Destination IP and Destination TCP/UDP Port fields of the packet) 6 (=Source/Destination IP and source/destination TCP/UDP Port fields of the packet) 7 (=Enhanced hashing mode) Support for particular options may vary by device.

OBJECT-TYPE

Agent LAG Threshold. This configures the threshold(i.e minimum number of active ports) value for trunk port .

OBJECT-TYPE

Agent LAG Local Preference Mode. Enables or disables the LAG interface's Local Preference Mode.

OBJECT-TYPE

Configures the MTU value for this LAG interface. The maximum value is dependent on the platform.

OBJECT-TYPE

LAG port flap counter.

OBJECT-TYPE

A detailed table of the switch's LAG config entries

OBJECT-TYPE

Switch's LAG config entry

OBJECT-TYPE

LAG index

OBJECT-TYPE

LAG port index

OBJECT-TYPE

LAG port speed. See agentPortType for a description and list of valid values.

OBJECT-TYPE

LAG port status. active(1) - Actively participating in the LAG. inactive(2) - Not participating in the LAG.

OBJECT-TYPE

LAG port flap counter.

OBJECT-TYPE

Agent LAG Static Capability. Configures whether Static LAGs are supported on this device.

OBJECT-TYPE

LAG Hashing Option. Valid values correspond to 1 (=Source MAC, VLAN, EtherType, and incoming port associated with the packet) 2 (=Destination MAC, VLAN, EtherType, and incoming port associated with the packet) 3 (=Source/Destination MAC, VLAN, EtherType, and incoming port associated with the packet) 4 (=Source IP and Source TCP/UDP fields of the packet) 5 (=Destination IP and Destination TCP/UDP Port fields of the packet) 6 (=Source/Destination IP and source/destination TCP/UDP Port fields of the packet) 7 (=Enhanced hashing mode) Support for particular options may vary by device. In BCM 53115 device only options 1 to 3 are support and only MAC address associated with the packet is used.

OBJECT-TYPE

Clear LAG stats. Will always return 0 when read.

OBJECT-IDENTITY

OBJECT-TYPE

The switch's network ip address

OBJECT-TYPE

The switch's network subnet mask

OBJECT-TYPE

The switch's network default gateway

OBJECT-TYPE

The switch's network Burned-In MAC address

OBJECT-TYPE

The switch's network locally administered MAC address

OBJECT-TYPE

The switch's network Mac Address Type

OBJECT-TYPE

The switch's network config protocol

OBJECT-TYPE

The switch's network config protocol dhcp is renewed. Will always return 0 when read.

OBJECT-TYPE

The switch's network config protocol on next bootup This object has been obsoleted by agentHTTPWebMode.

OBJECT-TYPE

Configures the use of the Java interface through the Web. This object has been obsoleted by agentHTTPJavaMode.

OBJECT-TYPE

The VLAN ID through which the switch can be managed using the agentNetworkIPAddress

OBJECT-TYPE

The network port IPv6 administrative state

OBJECT-TYPE

The network port IPv6 Gateway Address

OBJECT-TYPE

The list of IPv6 address prefixes for the network port.

OBJECT-TYPE

An interface entry containing objects of a particular IPv6 address prefix

OBJECT-TYPE

The service port IPv6 Address Prefix

OBJECT-TYPE

The service port IPv6 Address Prefix Length

OBJECT-TYPE

The service port IPv6 Eui Flag

OBJECT-TYPE

OBJECT-TYPE

The ipv6 address autoconfig allows the device to perform IPv6 stateless address auto-configuration to discover prefixes on the link and then to add the eui-64 based addresses to the network interface.

OBJECT-TYPE

The switch's network IPv6 config protocol

OBJECT-TYPE

The DHCPv6 Client unique DUID. This value cannot be modified

OBJECT-IDENTITY

OBJECT-TYPE

The no. of DHCPv6 messages of type ADVERTISE that have been received by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages of type REPLY that have been received by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages of type ADVERTISE that have been discarded by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages of type REPLY that have been discarded by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages received malformed by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages of type SOLICIT that have been sent by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages of type REQUEST that have been sent by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages of type RENEW that have been sent by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages of type REBIND that have been sent by the DHCPv6 client on the network port.

OBJECT-TYPE

The no. of DHCPv6 messages of type RELEASE that have been sent by the DHCPv6 client on the network port.

OBJECT-TYPE

Clear the DHCPv6 Client statistics on the network port. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator.

OBJECT-IDENTITY

OBJECT-TYPE

The switch's ServicePort ip address

OBJECT-TYPE

The switch's ServicePort subnet mask

OBJECT-TYPE

The switch's ServicePort default gateway

OBJECT-TYPE

The switch's ServicePort Burned-In MAC address

OBJECT-TYPE

The switch's ServicePort config protocol

OBJECT-TYPE

The switch's ServicePort protocol dhcp is renewed. Will always return 0 when read.

OBJECT-TYPE

The service port IPv6 administrative state

OBJECT-TYPE

The service port IPv6 Gateway Address

OBJECT-TYPE

The list of IPv6 address prefixes for the service port.

OBJECT-TYPE

An interface entry containing objects of a particular IPv6 address prefix

OBJECT-TYPE

The service port IPv6 Address Prefix

OBJECT-TYPE

The service port IPv6 Address Prefix Length

OBJECT-TYPE

The service port IPv6 Eui Flag

OBJECT-TYPE

OBJECT-TYPE

The ipv6 address autoconfig allows the device to perform IPv6 stateless address auto-configuration to discover prefixes on the link and then to add the eui-64 based addresses to the serviceport interface.

OBJECT-TYPE

The service port IPv6 protocol configured on the switch.

OBJECT-TYPE

The DHCPv6 Client unique DUID. This value cannot be modified

OBJECT-IDENTITY

OBJECT-TYPE

The no. of DHCPv6 messages of type ADVERTISE that have been received by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages of type REPLY that have been received by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages of type ADVERTISE that have been discarded by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages of type REPLY that have been discarded by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages received malformed by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages of type SOLICIT that have been sent by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages of type REQUEST that have been sent by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages of type RENEW that have been sent by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages of type REBIND that have been sent by the DHCPv6 client on the service port.

OBJECT-TYPE

The no. of DHCPv6 messages of type RELEASE that have been sent by the DHCPv6 client on the service port.

OBJECT-TYPE

Clear the DHCPv6 Client statistics on the service port. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates whether DHCP Vendor Classifier Id Option (60) is enabled for DHCP Network Client. If this object is set to 'true', DHCP Vendor Classifier Id mode is enabled globally. If this object is set to 'false', DHCP Vendor Classifier Id mode is disabled globally.

OBJECT-TYPE

When this object is set with a non-empty string, the DHCP Vendor Classifier Id Option (60) string is enabled for DHCP Network Client.

OBJECT-IDENTITY

OBJECT-TYPE

Creates a new SNMP Community entry. Defaults: IPAddress 0.0.0.0 IpMask 0.0.0.0 AccessMode read-only Status config

OBJECT-TYPE

A table of the switch's SNMP Config entries

OBJECT-TYPE

Switch's SNMP Config entry

OBJECT-TYPE

The switch's Snmp Community Index

OBJECT-TYPE

The switch's Snmp Community Name This name identifies each SNMP community; the name can be up to 16 characters, and it is case-sensitive. Community names in the SNMP community must be unique. If you make multiple entries using the same community name, the first entry is kept and processed and all duplicate entries are ignored.

OBJECT-TYPE

The switch's Snmp Community IP Address Client IP Address - This attribute is an IP address (or portion thereof) from which this device will accept SNMP packets with the associated community. The requesting entity's IP address is logical-ANDed with the Client IP Mask and the result must match the Client IP Address. Note: If the Client IP Mask is set to 0.0.0.0, a Client IP Address of 0.0.0.0 matches all IP addresses.

OBJECT-TYPE

The switch's Snmp Community IP Mask Client IP Mask - This attribute is a mask to be logical-ANDed with the requesting entity's IP address before comparison with the Client IP Address. If the result matches with Client IP Address then the address is an authenticated IP address. For example, if the Client IP Address is 9.47.128.0 and the corresponding Client IP Mask is 255.255.255.0, a range of incoming IP addresses would match, that is, the incoming IP addresses could be a value in the following range: 9.47.128.0 to 9.47.128.255. To have a specific IP address be the only authenticated IP address, set the Client IP Address to the required IP address and set the Client IP Mask to 255.255.255.255.

OBJECT-TYPE

The switch's Snmp Community Access Mode Access Mode - This value can be read-only or read/write. A community with a read-only access allows for switch information to be displayed. A community with a read/write access allows for configuration changes to be made and for information to be displayed.

OBJECT-TYPE

The switch's Snmp Community Status. active(1) - This community is active, allowing SNMP managers associated with this community to manage the switch according to its access right. notInService(2) - This community is not active; no SNMP requests using this community will be accepted. In this case the SNMP manager associated with this community cannot manage the switch until the Status is changed back to active(1). config(3) - The community Status must be set to this value in order to configure it. When creating a new community entry, initial Status will be set to this value. destroy(4) - Set to this value to remove the community from the agent.

OBJECT-TYPE

Creates a new trap receiver entry. Defaults: IPAddress 0.0.0.0 status config

OBJECT-TYPE

Trap messages are sent across a network to an SNMP Network Manager. These messages alert the manager to events occurring within the switch or on the network. Up to six simultaneous trap receivers are supported.

OBJECT-TYPE

Switch's Snmp Trace Receiver Config entry

OBJECT-TYPE

The switch's Snmp Trap Receiver Index

OBJECT-TYPE

The switch's Snmp Trap Receiver Community Name. This is the SNMP community name of the remote network manager; the name can be up to 16 characters, and is case-sensitive.

OBJECT-TYPE

IP Address - Each IP address parameter is four integer numbers. The numbers range from 0 to 255.

OBJECT-TYPE

The switch's Snmp Trap Reciever Status. active(1) - This trap receiver is active, allowing SNMP Traps to be sent to this receiver. notInService(2) - This trap reciever is not active; no SNMP Traps will be sent to this reciever until it's set back to active(1). config(3) - The trap reciever Status must be set to this value in order to configure it. When creating a new trap receiver entry, the Status will initially be set to this value. Note: agentSnmpTrapReceiverIPAddress must be set to non-zero before changing to active(1) or notInService(2). destroy(4) - Set to this value to remove the trap receiver entry from the agent.

OBJECT-TYPE

The version of trap sent to this Reciever. snmpv1(1) - This will send a SNMPv1 trap. snmpv2c(2) - This will send a SNMPv2c trap.

OBJECT-TYPE

IPv6 Address for SNMP receiver.

OBJECT-TYPE

The type of the snmptrap reciever address. The agentSnmpTrapReceiverAddress object is intepreted within the context of agentSnmpTrapReceiverAddressType

OBJECT-TYPE

The snmptrap reciever address. The type of this address is determined by the value of the agentSnmpTrapReceiverAddressType object. The values for agentSnmpTrapReceiverAddressType and agentSnmpTrapReceiverAddress must be consistent.

OBJECT-IDENTITY

OBJECT-TYPE

Authentication Flag - Enable/Disable authentication Flag.

OBJECT-TYPE

Link Up/Down Flag - Enable/Disable Link Up/Link Down traps for the entire switch. When set to Enable, the Link Up/Down traps will be sent only if the Link Trap flag setting associated with the port (Port Configuration Menu) is set to Enable.

OBJECT-TYPE

Multiple Users Flag - Enable/Disable Multiple User traps. When the value is set to Enable, a Multiple User Trap is sent whenever someone logs in to the terminal interface (EIA 232 or Telnet) and there is already an existing terminal interface session.

OBJECT-TYPE

Spanning Tree Flag - This flag enables the sending of new root traps and topology change notification traps.

OBJECT-TYPE

Broadcast Storm Flag - This flag enables or disables the broadcast storm trap. You must also enable Broadcast Storm Recovery Mode (see the Switch Configuration Menu). When this value is set to Enable and Broadcast Storm Recovery mode is set to Enable, the Broadcast Storm Start/End traps are sent when the switch enters and leaves Broadcast Storm Recovery.

OBJECT-TYPE

A source-interface selection on an Interface Index (like vlan based routing interface, port based routing interface, loopback interface, tunnel interface). A non-zero value indicates ifIndex for the corresponding interface entry in the ifTable is selected. A zero value indicates the source-interface un-selection.

OBJECT-TYPE

Get/Set the UDP port number that the SNMP server listens to for incoming requests. The port number is an integer value from 1025 to 65535. Before setting this object, check your system (e.g. using 'netstat') to make sure the desired port number is not currently being used by any other service. The default value for this object is 161. Note that changing the value of this object may cause existing SNMP transactions to cease communicating with the device until the client applications are reconfigured to use the new port number.

OBJECT-IDENTITY

OBJECT-TYPE

The switch's Spanning Tree Switch Status. This functionality is now handled by agentStpAdminMode

OBJECT-IDENTITY

OBJECT-TYPE

The address aging timeout. Specifies aging time in seconds (10 - 1000000) before a dynamic MAC address is erased from the Filtering Database. The default value is 300 seconds.

OBJECT-TYPE

The switch's address aging timeout table. This functionality is now handled by agentSwitchFdbAddressAgingTimeout.

OBJECT-TYPE

Aging information about a specific Filtering Database.

OBJECT-TYPE

The FDB entry's address aging timeout (in seconds)

OBJECT-TYPE

The switch's static Mac filtering table

OBJECT-TYPE

Per-port ingress/egress filter configuration based on VLAN Id and MAC address.

OBJECT-TYPE

The Static MAC Filter Vlan Id

OBJECT-TYPE

The Static MAC Filter MAC address

OBJECT-TYPE

The Static MAC Filter source port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

The Static MAC Filter destination port mask. When setting this value, the system will ignore configuration for ports not between the first and last valid ports. Configuration of any port numbers between this range that are not valid ports return a failure message, but will still apply configuration for valid ports. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table. Configuring destination port mask for a unicast MAC filter is not supported on some platforms.

OBJECT-TYPE

The Static MAC Filter status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP/MLD Snooping Global configuration entries.

OBJECT-TYPE

Represents entry for Snooping switch Configuration.

OBJECT-TYPE

The protocol type of network protocol in use.

OBJECT-TYPE

This enables or disables Snooping on the system.

OBJECT-TYPE

IGMP/MLD Snooping Port Mask. This allows configuration of IGMP/MLD Snooping on selected ports. IGMP/MLD Snooping cannot be enabled on an interface that has routing enabled, or is a member of a LAG. If a port which has IGMP/MLD Snooping enabled becomes enabled for routing, or is enlisted as a member of a LAG, IGMP/MLD Snooping functionality will be disabled on that port. IGMP/MLD Snooping functionality will be subsequently be reenabled if routing is disabled or LAG membership is removed from an interface that had previously had IGMP/MLD Snooping enabled. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

Multicast Control Frames Processed by CPU. The number of multicast control frames that have been processed by the CPU.

OBJECT-TYPE

This enables or disables IGMP/MLD Proxy Querier Mode on the system. If it is disabled then IGMP/MLD proxy query with source zero IP address is not sent in response to IGMP/MLD leave packet.

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP/MLD Snooping Interface configuration entries.

OBJECT-TYPE

Represents entry for a IGMP/MLD Snooping Interface.

OBJECT-TYPE

The port number to be selected. Each port maps to an interface.

OBJECT-TYPE

This enables or disables IGMP/MLD Snooping on a selected interface.

OBJECT-TYPE

The amount of time in seconds that a switch will wait for a report from a particular group on the selected interface before deleting the interface from the entry. This value must be greater than agentSwitchSnoopingIntfMaxResponseTime.

OBJECT-TYPE

The amount of time in seconds a switch will wait after sending a query on the selected interface because it did not receive a report for a particular group in that interface. This value must be less than agentSwitchSnoopingIntfGroupMembershipInterval. For IGMP Snooping, this value ranges from 1 to 25 and for MLD Snooping, this value ranges from 1 to 65.

OBJECT-TYPE

The amount of time in seconds that a switch will wait for a query to be received on the selected interface before the interface is removed from the list of interfaces with multicast routers attached.

OBJECT-TYPE

This enables or disables IGMP/MLD Snooping on the selected interface.

OBJECT-TYPE

This enables or disables Multicast Routing on the selected interface.

OBJECT-TYPE

This field lists all the VlanIDs which include the selected interface.

OBJECT-TYPE

This enables or disables IGMP/MLD Proxy Querier on the selected interface. If it is disabled then IGMP/MLD proxy query with source zero IP address is not sent in response to IGMP/MLD leave packet.

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP/MLD Snooping Vlan configuration entries.

OBJECT-TYPE

Represents entry for a IGMP/MLD Snooping Vlan.

OBJECT-TYPE

This enables or disables IGMP/MLD Snooping on a selected Vlan interface.

OBJECT-TYPE

The amount of time in seconds that a switch will wait for a report from a particular group on the selected vlan before deleting the interface participating in the vlan from the entry. This value must be greater than agentSwitchSnoopingIntfMaxResponseTime.

OBJECT-TYPE

The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This value must be less than agentSwitchSnoopingIntfGroupMembershipInterval. For IGMP Snooping, this value ranges from 1 to 25 and for MLD Snooping, this value ranges from 1 to 65.

OBJECT-TYPE

This enables or disables IGMP/MLD Snooping on the selected vlan.

OBJECT-TYPE

The amount of time in seconds that a switch will wait for a query to be received on the selected interface participating in the vlan before the interface is removed from the list of interfaces with multicast routers attached. This parameter is configurable only for exisiting Vlans.

OBJECT-TYPE

This enables or disables IGMP Snooping Report Suppression feature on the selected vlan.

OBJECT-TYPE

This enables or disables IGMP/MLD Proxy Querier on the selected vlan. If it is disabled then IGMP/MLD proxy query with source zero IP address is not sent in response to IGMP/MLD leave packet.

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP/MLD Static Mrouter Configuration parameters.

OBJECT-TYPE

Represents entry for a IGMP/MLD Static Mrouter.

OBJECT-TYPE

This enables or disables IGMP/MLD Mrouter on a per-interface per-vlan basis.

OBJECT-IDENTITY

OBJECT-TYPE

The Multicast Forwarding Database table

OBJECT-TYPE

Contains Forwarding and Filtering information per Vlan Index, MAC Address, and Component User.

OBJECT-TYPE

Vlan Index for which this entry is associated with.

OBJECT-TYPE

A multicast MAC address for which the switch has forwarding and or filtering information.

OBJECT-TYPE

The component that is responsible for this entry in the Multicast Forwarding Database.

OBJECT-TYPE

This displays the type of the entry. static(1) - Entries configured by the end user dynamic(2) - Entries added as a result of a learning process or protocol

OBJECT-TYPE

Text description of this multicast table entry.

OBJECT-TYPE

BitMask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

BitMask indicating which ports this entry indicates should be filtered. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

The Multicast Forwarding Database Summary table

OBJECT-TYPE

Summarizes the forwarding ports for all components registered for all MFDB table entries with the same Vlan Index and MAC Address.

OBJECT-TYPE

Vlan Index for which this entry is associated with.

OBJECT-TYPE

A multicast MAC address for which the switch has forwarding and or filtering information.

OBJECT-TYPE

Port Mask indicating which ports this entry indicates should be forwarded. To obtain port numbers from interface numbers, use the objects agentPortDot1dBasePort and agentPortIfIndex in the agentPortConfigTable table.

OBJECT-TYPE

This displays the maximum number of entries that can possibly be in the Multicast Forwarding Database table.

OBJECT-TYPE

This displays the largest number of entries that have been present in the Multicast Forwarding Database table. This value is also known as the MFDB high-water mark.

OBJECT-TYPE

This displays the current number of entries in the Multicast Forwarding Database table.

OBJECT-IDENTITY

OBJECT-TYPE

Configures the Double Vlan Tag Ethertype for the switch. If this object is supported, ethertype cannot be configured per port. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).

OBJECT-TYPE

A table of entries specifying the ethertype (TPID) values. This will let the user specify multiple ethertypes globally.

OBJECT-TYPE

A table entry specifying the ethertype (TPID) values. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).

OBJECT-TYPE

Ethertype value to identify incoming double tagged frames

OBJECT-TYPE

Specifies if this TPID is primary TPID for the switch or not. As the system needs one TPID to be active all the time, setting the object to false doesn't modify/remove the entry. Adding another entry and setting it to true overwrites the previous primary TPID.

OBJECT-TYPE

Row status

OBJECT-TYPE

A table entries specifying the ethertype (TPID) values per port.

OBJECT-TYPE

A table entry specifying the ethertype (TPID) value for a port.

OBJECT-TYPE

Port Id on to which the Ethertype value is mapped

OBJECT-TYPE

Ethertype value to identify incoming double tagged frames

OBJECT-TYPE

Controls the Double Vlan Tag mode on this port.

OBJECT-TYPE

Configures the Customer ID for the Double Vlan Tag for this port.

OBJECT-TYPE

Row status

OBJECT-IDENTITY

OBJECT-TYPE

Config switchconfig flowcontrol allows you to enable or disable 802.3x flow control for the switch. This value applies to only full-duplex mode ports. Enabling symmetric flow control allows the switch to send and receive pause frames. Enabling asymmetric flow control allows the switch to receive pause frames but it will not transmit pause frames.

OBJECT-TYPE

The switch config broadcast allows you to enable or disable broadcast storm recovery mode. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the broadcast traffic.

OBJECT-TYPE

Configures the broadcast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate.

OBJECT-TYPE

The switch config multicast allows you to enable or disable multicast storm recovery mode. When you specify Enable for multicast Storm Recovery and the multicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the multicast traffic.

OBJECT-TYPE

Configures the multicast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate.

OBJECT-TYPE

The switch config unicast allows you to enable or disable unicast storm recovery mode. When you specify Enable for unicast Storm Recovery and the unknown unicast traffic on any Ethernet port exceeds the configured threshold, the switch blocks (discards) the unknown unicast traffic.

OBJECT-TYPE

Configures the unicast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate.

OBJECT-TYPE

Configures the units of the threshold value to percentage of port speed or absolute packets per second.

OBJECT-TYPE

Configures the units of the threshold value to percentage of port speed or absolute packets per second.

OBJECT-TYPE

Configures the units of the threshold value to percentage of port speed or absolute packets per second.

OBJECT-IDENTITY

OBJECT-TYPE

The switch's MAC To VLAN association table

OBJECT-TYPE

VLAN to be assigned to untagged or priority tagged packets based on MAC address.

OBJECT-TYPE

The Mac address

OBJECT-TYPE

The VLAN the Mac address assigned to

OBJECT-TYPE

The Mac to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry

OBJECT-IDENTITY

OBJECT-TYPE

The switch's protected port mapping table

OBJECT-TYPE

Protected ports assigned to groups.

OBJECT-TYPE

The group that this port belongs to

OBJECT-TYPE

The name of the group

OBJECT-TYPE

The set of ports that are protected in this group

OBJECT-IDENTITY

OBJECT-TYPE

The switch's Subnet To VLAN association table

OBJECT-TYPE

VLAN to be assigned to untagged or priority tagged packets based on IP address and Subnet Mask.

OBJECT-TYPE

The ip address

OBJECT-TYPE

The subnet mask

OBJECT-TYPE

The VLAN that the IP address and subnet mask assigned to

OBJECT-TYPE

The Subnet to VLAN association row status. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry

OBJECT-IDENTITY

OBJECT-TYPE

A table of the IGMP/MLD Snooping Querier Global configuration entries.

OBJECT-TYPE

Represents entry for Snooping Querier Configuration.

OBJECT-TYPE

This enables or disables Snooping Querier on the system.

OBJECT-TYPE

This specifies the multicast protocol versions that are supported by the system.

OBJECT-TYPE

This specifies the default source ip address to be used while generating general queries.

OBJECT-TYPE

This specified the timer interval after which the system generates general queries.

OBJECT-TYPE

This specified the timer interval after which the detected other querier information is no longer valid.

OBJECT-TYPE

A table of the Snooping Querier Vlan configuration entries.

OBJECT-TYPE

Represents entry for a Snooping Querier configurable Vlan.

OBJECT-TYPE

This enables or disables Snooping Querier on a selected Vlan interface.

OBJECT-TYPE

This specifies the current state of the Snooping Querier on a selected vlan interface

OBJECT-TYPE

This enables or disables the Snooping Querier Election Participation mode. When enabled snooping querier switch will participate in querier election up on discovering another querier in the specified vlan. When disabled, up on discovering another querier, snooping querier moves to non-querier state.

OBJECT-TYPE

This specifies the default source ip address to be used while generating general queries on the specified vlan.

OBJECT-TYPE

This specifies the multicast protocol version that is currently being used by the snooping switch for the specified vlan while generating query messages.

OBJECT-TYPE

The amount of time in seconds a switch will wait after sending a query on the selected vlan because it did not receive a report for a particular group in the interface participating in the vlan. This object is valid only when agentSwitchSnoopingQuerierOperVersion object is valid. (-1) - indicates that parameter is not available; ( 0) - indicates that response time is less then 1 second.

OBJECT-TYPE

This specifies the last querier's ip address for the specified vlan. It represents the detected other multicast querier in the vlan.

OBJECT-TYPE

This specifies the multicast protocol version that is currently being used by the detected other multicast querier for the specified vlan. (-1) - indicates that parameter is not available.

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates whether Sender MAC validation in the ARP packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled.

OBJECT-TYPE

This object indicates whether Target MAC validation in the ARP Response packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled.

OBJECT-TYPE

This object indicates whether IP address validation in the ARP packets is enabled. If this object is set to 'true', validation is enabled. If this object is set to 'false', validation is disabled.

OBJECT-TYPE

A table provides the mechanism to control Dynamic ARP Inspection per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added.

OBJECT-TYPE

A row instance contains the configuration for Dynamic ARP Inspection at each existing VLAN.

OBJECT-TYPE

This object indicates the VLAN number on which Dynamic ARP Inspection feature is configured.

OBJECT-TYPE

This object indicates whether Dynamic ARP Inspection is enabled in this VLAN. If this object is set to 'true', Dynamic ARP Inspection is enabled. If this object is set to 'false', Dynamic ARP Inspection is disabled.

OBJECT-TYPE

This object indicates whether the Dynamic ARP Inspection logging is enabled on this VlAN. If this object is set to 'true', Dynamic ARP Inspection logging is enabled. If this object is set to 'false', Dynamic ARP Inspection loging is disabled.

OBJECT-TYPE

This object indicates the ARP ACL name set for this VLAN.

OBJECT-TYPE

This object indicates whether the ARP ACL set for this VLAN has static flag set. If this object is set to 'true', static flag is enabled. If this object is set to 'false', static flag is disabled.

OBJECT-TYPE

Clear the DAI statistics on all vlans. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator.

OBJECT-TYPE

A table provides the mechanism to control Dynamic ARP Inspection per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added.

OBJECT-TYPE

A row instance contains the Dynamic ARP Inspection statistics per VLAN.

OBJECT-TYPE

This object indicates the VLAN number on which Dynamic ARP Inspection statistics are retrieved.

OBJECT-TYPE

Number of valid ARP packets forwarded by DAI.

OBJECT-TYPE

Number of invalid ARP packets dropped by DAI.

OBJECT-TYPE

Number of ARP packets that were dropped by DAI as there is no matching DHCP Snooping binding entry found.

OBJECT-TYPE

Number of ARP packets that were forwarded by DAI as there is a matching DHCP Snooping binding entry found.

OBJECT-TYPE

Number of ARP packets that were dropped by DAI as there is no matching ARP ACL rule found for this Vlan and the static flag is set on this vlan.

OBJECT-TYPE

Number of ARP packets that were permitted by DAI as there is a matching ARP ACL rule found for this Vlan.

OBJECT-TYPE

Number of ARP packets that were dropped by DAI as the sender mac address in ARP packet didn't match the source mac in ethernet header.

OBJECT-TYPE

Number of ARP packets that were dropped by DAI as the target mac address in ARP reply packet didn't match the destination mac in ethernet header.

OBJECT-TYPE

Number of ARP packets that were dropped by DAI as the sender IP address in ARP packet or target IP address in ARP reply packet is invalid. Invalid addresses include 0.0.0.0, 255.255.255.255, IP multicast addresses, class E addresses (240.0.0.0/4), loopback addresses (127.0.0.0/8).

OBJECT-TYPE

A table provides the mechanism to configure the trust state for Dynamic ARP Inspection purpose at each physical interface capable of this feature.

OBJECT-TYPE

A row instance contains the configuration for Dynamic ARP Inspection at each physical interface capable of this feature.

OBJECT-TYPE

This object indicates whether the interface is trusted for Dynamic ARP Inspection purpose. If this object is set to 'true', the interface is trusted. ARP packets coming to this interface will be forwarded without checking. If this object is set to 'false', the interface is not trusted. ARP packets coming to this interface will be subjected to ARP inspection.

OBJECT-TYPE

This object indicates rate limit value for Dynamic ARP Inspection purpose. If the incoming rate of ARP packets exceeds the value of this object for consecutively burst interval seconds, ARP packets will be dropped. Value of -1 indicates that there is no rate limit.

OBJECT-TYPE

This object indicates the burst interval value for rate limiting purpose on this interface.

OBJECT-IDENTITY

OBJECT-TYPE

A table of the ARP ACL entries

OBJECT-TYPE

Represents entry for an ARP ACL

OBJECT-TYPE

Name of the ARP ACL, which must consist of 1 to 31 alphanumeric characters and uniquely identify this ARP ACL. This object must be set to complete a new ARP ACL row instance.

OBJECT-TYPE

The status of this conceptual row. Entries can not be deleted until all rows in arpAclRuleTable with corresponding values of arpAclIndex have been deleted. active(1) - this ACL instance is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

OBJECT-TYPE

A table of the ARP ACL Rule entries

OBJECT-TYPE

Represents entry for a set of ARP ACL-match rules

OBJECT-TYPE

Sender IP address match value for the ARP ACL.

OBJECT-TYPE

Sender MAC address match value for the ARP ACL.

OBJECT-TYPE

The status of this conceptual row. active(1) - this ACL Rule is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates whether DHCP Snooping is enabled globally. If this object is set to 'true',admin mode is enabled globally. If this object is set to 'false',admin mode is disabled globally.

OBJECT-TYPE

This object indicates whether source Mac address in the received DHCP Message needs to be verified or not. If this object is set to 'true',verifyMac is enabled globally. If this object is set to 'false',verifyMac is disabled globally.

OBJECT-TYPE

A table provides the mechanism to control DHCP SNOOPING per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added.

OBJECT-TYPE

A row instance contains the configuration for DHCP SNOOPING at each existing VLAN.

OBJECT-TYPE

This object indicates the VLAN number on which DHCP SNOOPING Inspection feature is configured.

OBJECT-TYPE

This object indicates whether DHCP SNOOPING is enabled in this VLAN. If this object is set to 'true', DHCP SNOOPING is enabled. If this object is set to 'false', DHCP SNOOPING is disabled.

OBJECT-TYPE

A table provides the mechanism to configure the trust state for DHCP snooping purpose at each physical interface capable of this feature.

OBJECT-TYPE

A row instance contains the configuration for DHCP snooping at each physical interface capable of this feature.

OBJECT-TYPE

This object indicates whether the interface is trusted for DHCP snooping purpose.

OBJECT-TYPE

This object indicates whether the Logging needs on DHCP snooping validations or not

OBJECT-TYPE

This object indicates rate limit value for DHCP Snooping purpose. If the incoming rate of DHCP packets exceeds the value of this object for consecutively burst interval seconds, DHCP packets will be dropped. Value of -1 indicates that there is no rate limit.

OBJECT-TYPE

This object indicates the burst interval value for rate limiting purpose on this interface. Value of -1 indicates that there is no burst interval.

OBJECT-TYPE

A table provides the mechanism to configure the IPSG at each physical interface capable of this feature.

OBJECT-TYPE

A row instance contains the configuration for IPSG at each physical interface capable of this feature.

OBJECT-TYPE

This object indicates whether IP packets received on this interface are filtered based on whether IP Source Guard considers the source IP address to be a valid client address. Setting this variable to false automatically sets agentIpsgIfPortSecurity to false.

OBJECT-TYPE

This object indicates whether IP packets received on this interface are filtered based on whether IP Source Guard considers the source MAC address to be a valid client address. The port security option cannot be enabled unless agentIpsgIfVerifySource is also enabled. That is, MAC address filtering cannot be done without also doing IP address filtering. But IP address filtering can be done without MAC address filtering. Once the port security option is enabled, it can only be disabled by disabling agentIpsgIfVerifySource.

OBJECT-TYPE

Clear the DHCP snooping statistics on all ports. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator.

OBJECT-TYPE

A table provides the mechanism for statics of DHCP snooping.

OBJECT-TYPE

A row instance contains the DHCP snooping statistics per VLAN.

OBJECT-TYPE

This object indicates the number of failure verifications of client mac address with source mac address

OBJECT-TYPE

This object indicates the number of invalid DHCP release, request and decline messages

OBJECT-TYPE

This object indicates the number of invalid DHCP server mesaages

OBJECT-TYPE

A table of the IPSG static entries

OBJECT-TYPE

Represents a binding in IPSG table

OBJECT-TYPE

Interface on which this IPSG binding is going to be added.

OBJECT-TYPE

VLAN to whcig this IPSG binding is going to be added.

OBJECT-TYPE

IP address match value for the IPSG Binding.

OBJECT-TYPE

MAC address match value for the IPSG Binding.

OBJECT-TYPE

The status of this conceptual row. active(1) - this IPSG Binding is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

OBJECT-TYPE

A table of the IPSG dynamic entries

OBJECT-TYPE

Represents a binding in IPSG table

OBJECT-TYPE

Interface on which this IPSG binding is added.

OBJECT-TYPE

VLAN to which this IPSG binding is going to be added.

OBJECT-TYPE

Sender IP address match value for the IPSG Binding.

OBJECT-TYPE

MAC address match value for the IPSG Binding.

OBJECT-TYPE

A table of the DHCP SNOOPING static entries

OBJECT-TYPE

Represents a binding in DHCP SNOOPING table

OBJECT-TYPE

Interface on which this DHCP SNOOPING binding is going to be added.

OBJECT-TYPE

VLAN to which this DHCP SNOOPING binding is going to be added.

OBJECT-TYPE

MAC address match value for the DHCP SNOOPING Binding.

OBJECT-TYPE

IP address match value for the DHCP SNOOPING Binding.

OBJECT-TYPE

The status of this conceptual row. active(1) - this DHCP SNOOPING Binding is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

OBJECT-TYPE

A table of the DHCP SNOOPING Dynamic entries

OBJECT-TYPE

Represents a binding in DHCP SNOOPING table

OBJECT-TYPE

Interface on which this DHCP SNOOPING binding is going to be added.

OBJECT-TYPE

VLAN to whcig this DHCP SNOOPING binding is going to be added.

OBJECT-TYPE

MAC address match value for the DHCP SNOOPING Binding.

OBJECT-TYPE

IP address match value for the DHCP SNOOPING Binding.

OBJECT-TYPE

This specifies the period for which the DHCP SNOOPING Binding is valid.

OBJECT-TYPE

This object indicates the file name on the remote machine to save the DHCP Snooping bindings. This will be set only when we have a valid remote IP.

OBJECT-TYPE

This object indicates the IP address of the remote machine to save the DHCP Snooping bindings. This will be set only when we have a valid file name.

OBJECT-TYPE

This object indicates the perodic time interval to save the DHCP Snooping bindings.

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates whether DHCP L2 Relay is enabled globally. If this object is set to 'true',admin mode is enabled globally. If this object is set to 'false',admin mode is disabled globally.

OBJECT-TYPE

A table provides the mechanism to enable/disable and configure the trust state for DHCP L2Relay purpose at each physical interface capable of this feature.

OBJECT-TYPE

A row instance contains the configuration for DHCP L2 Relay at each physical interface capable of this feature.

OBJECT-TYPE

This object indicates whether the DHCP L2Relay is enabled or not

OBJECT-TYPE

This object indicates whether the interface is trusted for DHCP L2 Relay purpose.

OBJECT-TYPE

A table provides the mechanism to control DHCP L2 Relay per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added.

OBJECT-TYPE

A row instance contains the configuration for DHCP L2 Relay at each existing VLAN.

OBJECT-TYPE

This object indicates the VLAN number on which DHCP L2 Relay feature is configured.

OBJECT-TYPE

This object indicates whether DHCP L2 Relay is enabled in this VLAN. If this object is set to 'true', DHCP L2 Relay is enabled. If this object is set to 'false', DHCP L2 Relay is disabled.

OBJECT-TYPE

This object indicates whether DHCP CircuitId is enabled for L2 relaying in this VLAN. If this object is set to 'true', DHCP CircuitId is enabled. If this object is set to 'false', DHCP CircuitId is disabled.

OBJECT-TYPE

When this object is set with a non-empty string, DHCP RemoteId is enabled for L2 relaying in this VLAN.

OBJECT-TYPE

Clear the DHCP L2Relay statistics on all ports. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator.

OBJECT-TYPE

A table provides the mechanism for statics of DHCP L2 Relay.

OBJECT-TYPE

A row instance contains the DHCP L2Relay statistics per interface.

OBJECT-TYPE

This object indicates the number of DHCP server messages received with Option-82 field on the untrusted interface.

OBJECT-TYPE

This object indicates the number of DHCP client messages received with Option-82 field on the untrusted interface.

OBJECT-TYPE

This object indicates the number of DHCP server messages received without Option-82 field on the trusted interface.

OBJECT-TYPE

This object indicates the number of DHCP client messages received without Option-82 field on the trusted interface.

OBJECT-IDENTITY

OBJECT-TYPE

This enables or disables Voice VLAN on the system.

OBJECT-TYPE

A table of the Voice Vlan device entries.

OBJECT-TYPE

Represents entry for a Voice Device on the interface.

OBJECT-TYPE

The interface number of this interface.

OBJECT-TYPE

The Voice Device Mac address

OBJECT-IDENTITY

OBJECT-TYPE

Displays if an address conflict was detected on the switch since the last reset of the status or the last conflict detection run. Set to 'true' if detected, 'false' otherwise.

OBJECT-TYPE

Clear the last address conflict detection status in the switch. A value of reset(1) is used to reset the status. A read on this object always returns the value none (0). The value none (0) cannot be forcibly set by the administrator.

OBJECT-TYPE

The reported conflicting IP address on the switch since the last reset of the conflict detection status or the last conflict detection run.

OBJECT-TYPE

The MAC address of the host corresponding to the reported conflicting IP address on the switch since the last reset of the conflict detection status or the last conflict detection run.

OBJECT-TYPE

Time since the last address conflict was detected. It is displayed in days, hours, minutes and seconds. It is set to a valid value only when the conflict detection status is 'true'.

OBJECT-TYPE

The IP address on the switch reported to have a conflict with another host's IP address.

OBJECT-TYPE

The MAC address of the host that has an IP address conflicting with the IP address on the switch.

OBJECT-TYPE

Trigger the action to run the active address conflict detection. A value of run(1) is used to issue the action command. A read on this object always returns the value none(0). The value none (0) cannot be forcibly set by the administrator.

OBJECT-IDENTITY

OBJECT-TYPE

Displays the current active SDM Template.

OBJECT-TYPE

Configures the next active template. It will be active only after the next reboot. To revert to the default template after the next reboot, use the option default(0).

OBJECT-IDENTITY

OBJECT-TYPE

Displays Switch Database Management Template Information.

OBJECT-TYPE

Information about a SDM Template table entry.

OBJECT-TYPE

The SDM Template type this instance is associated with.

OBJECT-TYPE

The maximum number of entries in the IPv4 Address Resolution Protocol (ARP) cache for routing interfaces.

OBJECT-TYPE

The maximum number of IPv4 unicast forwarding table entries.

OBJECT-TYPE

The maximum number of IPv6 Neighbor Discovery Protocol (NDP) cache entries.

OBJECT-TYPE

The maximum number of IPv6 unicast forwarding table entries.

OBJECT-TYPE

The maximum number of Equal cost next hops that can be installed in the IPv4 and IPv6 unicast forwarding tables.

OBJECT-TYPE

The maximum number of IPv4 multicast forwarding table entries.

OBJECT-TYPE

The maximum number of IPv6 multicast forwarding table entries.

OBJECT-IDENTITY

OBJECT-TYPE

Mode changes are effective from the next reload of the Switch. The cut-through feature may not be present on all switches. Use - agentSwitchCutThroughRunningModeStatus - MIB to check if the feature is present on your switch.

OBJECT-TYPE

This gives the current running mode of the cut-through feature on switch. Note that Mode changes are effective from the next reload of the Switch. so running mode may be different than the configured mode. A value of not-supported(3) means that the feature is not present on the switch.

OBJECT-TYPE

This gives the configured mode of cut-through feature on switch. Note that Mode changes are effective from the next reload of the Switch. so running mode may be different than the configured mode. A value of not-supported(3) means that the feature is not present on the switch.

OBJECT-IDENTITY

OBJECT-IDENTITY

X PCS/PMA, unknown PMD. MAU MIB augmentation

OBJECT-IDENTITY

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

Enables vlan for Private Vlan and configures private vlan type.

OBJECT-TYPE

This field lists all the VlanIDs which are associated with the selected vlan. If the selected vlan type is not primary(1), a zero-length bitmask is returned.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

Configures the primary host vlan association with the interface. This must be configured along with agentPrivateVlanIntfAssocHostSecondary before the association will be operational. NOTE: Both agentPrivateVlanIntfAssocHostPrimary and agentPrivateVlanIntfAssocHostSecondary objects must be specified at the same time.

OBJECT-TYPE

Configures the secondary host vlan association with the interface. This must be configured along with agentPrivateVlanIntfAssocHostPrimary before the association will be operational. NOTE: Both agentPrivateVlanIntfAssocHostPrimary and agentPrivateVlanIntfAssocHostSecondary objects must be specified at the same time.

OBJECT-TYPE

Configures the primary promiscuous vlan association with the interface. This must be configured along with agentPrivateVlanIntfAssocPromiscuousSecondary before the association will be operational.

OBJECT-TYPE

Configures the secondary promiscuous vlan association with the interface. This must be configured along with agentPrivateVlanIntfAssocPromiscuousPrimary before the association will be operational.

OBJECT-TYPE

Shows the operational private vlans associated with the interface.

OBJECT-IDENTITY

OBJECT-TYPE

The switch's private group mapping table

OBJECT-TYPE

Private groups assigned to ports.

OBJECT-TYPE

The private group id that port belongs to

OBJECT-TYPE

The name of the Private group

OBJECT-TYPE

The mode of port in private group is either isloated or community

OBJECT-TYPE

Private Group VLAN can only be created through multiple variable bindings taking all the objects of of the AgentSwitchPrivateGroupEntry. Supported values: active(1) - valid entry createAndGo(4) - used to create a new entry destroy(6) - removes the entry

OBJECT-TYPE

The switch's private group portlist mapping table

OBJECT-TYPE

List of ports assigned to private groups.

OBJECT-TYPE

The private group id that port belongs to

OBJECT-TYPE

The name of the Private group

OBJECT-TYPE

The list of ports in private group

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates whether DHCPv6 SNOOPING is enabled globally. If this object is set to 'true',admin mode is enabled globally. If this object is set to 'false',admin mode is disabled globally.

OBJECT-TYPE

This object indicates whether source Mac address in the received dhcpv6 Message needs to be verified or not. If this object is set to 'true',verifyMac is enabled globally. If this object is set to 'false',verifyMac is disabled globally.

OBJECT-TYPE

A table provides the mechanism to control DHCPv6 SNOOPING per VLAN. When a VLAN is created in a device supporting this table, a corresponding entry of this table will be added.

OBJECT-TYPE

A row instance contains the configuration for dhcpv6 SNOOPING at each existing VLAN.

OBJECT-TYPE

This object indicates the VLAN number on which DHCPv6 SNOOPING Inspection feature is configured.

OBJECT-TYPE

This object indicates whether DHCPv6 SNOOPING is enabled in this VLAN. If this object is set to 'true', DHCPv6 SNOOPING is enabled. If this object is set to 'false', DHCPv6 SNOOPING is disabled.

OBJECT-TYPE

A table provides the mechanism to configure the trust state for DHCPv6 SNOOPING purpose at each physical interface capable of this feature.

OBJECT-TYPE

A row instance contains the configuration for DHCPv6 SNOOPING at each physical interface capable of this feature.

OBJECT-TYPE

This object indicates whether the interface is trusted for DHCPv6 SNOOPING purpose.

OBJECT-TYPE

This object indicates whether the Logging needs on DHCPv6 SNOOPING validations or not

OBJECT-TYPE

This object indicates rate limit value for dhcpv6 Snooping purpose. If the incoming rate of dhcpv6 packets exceeds the value of this object for consecutively burst interval seconds, dhcpv6 packets will be dropped. Value of -1 indicates that there is no rate limit.

OBJECT-TYPE

This object indicates the burst interval value for rate limiting purpose on this interface. Value of -1 indicates that there is no burst interval.

OBJECT-TYPE

A table provides the mechanism to configure the IPSG at each physical interface capable of this feature.

OBJECT-TYPE

A row instance contains the configuration for IPSG at each physical interface capable of this feature.

OBJECT-TYPE

This object indicates whether the interface is enabled for IPv6SG to forward the data based up on source Ip address

OBJECT-TYPE

This object indicates whether the interface is enabled for IPv6SG to forward the data based up on source mac address in fdb table

OBJECT-TYPE

Clear the DHCPv6 SNOOPING statistics on all ports. A value of reset(1) is used to reset the statistics. A read on this object will always return the value none(0). The value none(0) cannot be forcibly set by the administrator.

OBJECT-TYPE

A table provides the mechanism for statics of DHCPv6 SNOOPING.

OBJECT-TYPE

A row instance contains the DHCPv6 SNOOPING statistics per VLAN.

OBJECT-TYPE

This object indicates the number of failure verifications of client mac address with source mac address

OBJECT-TYPE

This object indicates the number of invalid dhcpv6 release, request and decline messages

OBJECT-TYPE

This object indicates the number of invalid dhcpv6 server mesaages

OBJECT-TYPE

A table of the IPv6SG static entries

OBJECT-TYPE

Represents a binding in IPv6SG table

OBJECT-TYPE

Interface on which this IPv6SG binding is going to be added.

OBJECT-TYPE

VLAN to which this IPv6SG binding is going to be added.

OBJECT-TYPE

IPv6 address match value for the IPv6SG binding.

OBJECT-TYPE

MAC address match value for the IPv6SG Binding.

OBJECT-TYPE

The status of this conceptual row. active(1) - this IPv6SG Binding is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

OBJECT-TYPE

A table of the IPv6SG dynamic entries

OBJECT-TYPE

Represents a binding in IPSG table

OBJECT-TYPE

Interface on which this IPv6SG binding is added.

OBJECT-TYPE

VLAN to which this IPv6SG binding is going to be added.

OBJECT-TYPE

Sender IPv6 address match value for the IPv6SG binding.

OBJECT-TYPE

MAC address match value for the IPv6SG Binding.

OBJECT-TYPE

A table of the DHCPv6 SNOOPING static entries

OBJECT-TYPE

Represents a static binding in DHCPv6 SNOOPING table

OBJECT-TYPE

Interface on which this static DHCPv6 SNOOPING binding is going to be added.

OBJECT-TYPE

VLAN to which this static DHCPv6 SNOOPING binding is going to be added.

OBJECT-TYPE

MAC address match value for the static DHCPv6 SNOOPING Binding.

OBJECT-TYPE

IP address match value for the static DHCPv6 SNOOPING Binding.

OBJECT-TYPE

The status of this conceptual row. active(1) - this static DHCPv6 SNOOPING Binding is active createAndGo(4) - set to this value to create an instance destroy(6) - set to this value to delete an instance

OBJECT-TYPE

A table of the DHCPv6 SNOOPING Dynamic entries

OBJECT-TYPE

Represents a dynamic binding in DHCPv6 SNOOPING table

OBJECT-TYPE

Interface on which this dynamic DHCPv6 SNOOPING binding is going to be added.

OBJECT-TYPE

VLAN to which this dynamic DHCPv6 SNOOPING binding is going to be added.

OBJECT-TYPE

MAC address match value for the dynamic DHCPv6 SNOOPING Binding.

OBJECT-TYPE

IP address match value for the dynamic DHCPv6 SNOOPING Binding.

OBJECT-TYPE

This specifies the period for which the dynamic DHCPv6 SNOOPING Binding is valid.

OBJECT-TYPE

This object indicates the file name on the remote machine to save the DHCPv6 Snooping bindings. This will be set only when we have a valid remote IP.

OBJECT-TYPE

This object indicates the IP address of the remote machine to save the DHCPv6 Snooping bindings. This will be set only when we have a valid file name.

OBJECT-TYPE

This object indicates the perodic time interval to save the DHCPv6 Snooping bindings.

OBJECT-TYPE

The (conceptual) table listing the IP multicast Source Specific Multicast Groups for which there are members on a particular interface and VLAN.

OBJECT-TYPE

An entry (conceptual row) in the agentSwitchSnoopSSMGroupTable.

OBJECT-TYPE

The address type of the agentSwitchSnoopSSMGroupTable entry. This value applies to both the agentSwitchSnoopSSMGroupAddress and the agentSwitchSnoopSSMGroupLastReporter entries.

OBJECT-TYPE

The IP multicast group address for which this entry contains information. The InetAddressType, e.g. IPv4 or IPv6, is identified by the agentSwitchSnoopSSMGroupAddressType variable in the agentSwitchSnoopSSMGroup table.

OBJECT-TYPE

The interface for which this entry contains information for an IP multicast group address.

OBJECT-TYPE

The VLAN for which this entry contains information for an IP multicast group address.

OBJECT-TYPE

The IP address of the source of the last membership report received for this IP Multicast group address on this interface and VLAN. The InetAddressType, e.g. IPv4 or IPv6, is identified by the agentSwitchSnoopSSMGroupAddressType variable in the agentSwitchSnoopSSMGroup table.

OBJECT-TYPE

The state in which the interface is currently set. The value indicates the relevance of the corresponding source list entries in the SrcList Table (agentSwitchSnoopSSMSrcListTable).

OBJECT-TYPE

The (conceptual) table listing the Source List entries corresponding to each VLAN, interface and SSM multicast group pair on a MGMD Snooping switch.

OBJECT-TYPE

An entry (conceptual row) in the agentSwitchSnoopSSMSrcListTable.

OBJECT-TYPE

The address type of the InetAddress variables in this table. This value applies to the agentSwitchSnoopSSMSrcListHostAddress and agentSwitchSnoopSSMSrcListAddress entries.

OBJECT-TYPE

The IP multicast group address for which this entry contains information.

OBJECT-TYPE

The interface for which this entry contains information for an IP multicast group address.

OBJECT-TYPE

The VLAN for which this entry contains information for an IP multicast group address.

OBJECT-TYPE

The host address to which this entry corresponds. The agentSwitchSnoopSSMGroupSourceFilterMode value for this Group address, interface and VLAN indicates whether this Host address is included or excluded.

OBJECT-TYPE

MGMD Snooping Source Specific Multicast Forwarding database Table.

OBJECT-TYPE

An entry is created by IGMP Snooping for each group learned in the VLAN.

OBJECT-TYPE

This object indicates the VLAN in which the group is learned.

OBJECT-TYPE

This object indicates IP multicast address type learned by MGMD Snooping.

OBJECT-TYPE

This object indicates IP multicast address learned by MGMD Snooping.

OBJECT-TYPE

This object indicates IP Source address learned by MGMD Snooping.

OBJECT-TYPE

This object indicates the set of ports on which MGMD Membership Reports are received for the group indicating interest to receive traffic sent to the group.

OBJECT-TYPE

This object indicates the set of ports on which MGMD Membership Reports are received for the group indicating interest to not to receive traffic sent to the group.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

The port or LAG number to be selected. Each port/LAG maps to an interface.

OBJECT-TYPE

Configure the VLAN membership mode of a port.

OBJECT-TYPE

Configures the Access VLAN Id for the interface.

OBJECT-TYPE

Configures the Native VLAN Id for the interface.

OBJECT-TYPE

Describes the Native VLAN tagging for the interface. 'disable' mean that packets marked with Native VLAN are transmitted untagged from Trunk port.

OBJECT-TYPE

Configures the allowed VLAN list of Trunk switch interface.

OBJECT-TYPE

Shows the allowed untagged VLAN list of general switch interface.

OBJECT-TYPE

Shows the allowed tagged VLAN list of general switch interface.

OBJECT-TYPE

Shows the Forbidden VLAN list of general switch interface.

OBJECT-TYPE

Shows the list of dynamically added VLANs for general switch interface.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Transfer upload mode configures the mode to use when uploading from the switch. The mode is either X/Y/ZMODEM, TFTP, SFTP or SCP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port. SFTP and SCP are only allowed if the SSH feature is present. Upload to USB is allowed only if the USB feature is present.

OBJECT-TYPE

Transfer upload server IP configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP, or SCP. The address is 4 integer bytes ranging from 0 to 255. This object is deprecated in favour of agentTransferUploadServerAddress and agentTransferUploadServerAddressType.

OBJECT-TYPE

Transfer upload path configures the directory path where the file is to be uploaded to. The switch remembers the last file path used.

OBJECT-TYPE

Transfer upload filename configures the file name for the file being uploaded from the switch. It can be up to 31 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 17 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\scripts\ and File Name set to script2.scr. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP and object agentTransferUploadDataType is not set to type code.

OBJECT-TYPE

Transfer upload datatype configures the type of file to upload from the switch. The types for upload are: - Configuration File - Error log - Message log - Trap log - Banner File - Code - Language Pack file - Captured CPU packets file - Startup Config file - Backup Config file - Factory Default Config file - Config Script file - Startup Log file - Operational Log file - Crash Log File - Tech Support File

OBJECT-TYPE

Transfer upload start will start an upload transfer. The agentTransferUploadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.

OBJECT-TYPE

Indicates the current status of an upload transfer.

OBJECT-TYPE

The type of the serverip address, as defined in the InetAddress MIB. The agentTransferUploadServerAddress object is intepreted within the context of agentTransferUploadServerAddressType

OBJECT-TYPE

Transfer upload serverip configures the IP address of the server where the file is to be uploaded to.It is valid only when the Transfer Mode is TFTP, SFTP or SCP. The type of this address is determined by the value of the agentTransferUploadServerAddressType object. The values for agentTransferUploadServerAddressType and agentTransferUploadServerAddress must be consistent.

OBJECT-TYPE

Transfer upload image name. Sets the image to be uploaded as the specified name. Imagename cannot be set to unknown(1) option. When no name is set this object returns unknown(1) by default. Note: Imagename, File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP.

OBJECT-TYPE

Username applicable to secure upload types, i.e., SFTP or SCP and FTP.

OBJECT-TYPE

Password applicable to secure upload types, i.e. SFTP or SCP and FTP.

OBJECT-TYPE

Transfer upload remote filename configures the file name for the file being created remotely. It can be up to 31 alphanumeric characters. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP.

OBJECT-IDENTITY

OBJECT-TYPE

Transfer download mode configures the mode to use when downloading to the switch. The mode is either X/Y/ZMODEM, TFTP, FTP, SFTP or SCP. X/Y/ZMODEM is valid only when the file transfer is initiated by the serial EIA 232 port. SFTP and SCP are only allowed if the SSH feature is present. Download from USB is only allowed if the USB feature is present.

OBJECT-TYPE

Transfer download serverip configures the IP address of the server where the file is located. It is valid only when the Transfer Mode is TFTP, SFTP or SCP. The address is 4 integer bytes ranging from 0 to 255. This object is deprecated in favour of agentTransferDownloadServerAddress and agentTransferDownloadServerAddressType.

OBJECT-TYPE

Transfer download path configures the directory path where the file is located. The switch remembers the last file path used.

OBJECT-TYPE

Transfer download filename configures the file name for the file being downloaded to the switch. It can be up to 31 alphanumeric characters. The switch remembers the last file name used. File path can be appended to the file name if the string is less than 32 characters. Otherwise, the File Path field will need to be used and the File Name will be appended to the File Path as is. An example would be File Path set to c:\tftp\scripts\ and File Name set to script1.scr. Note: File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP and the object agentTransferDownloadDataType download type is not set to code

OBJECT-TYPE

Transfer download datatype configures the type of file to download to the switch. The types for download are: code - Code File config - Configuration File sshkey-rsa1 - SSH-1 RSA Key File sshkey-rsa2 - SSH-2 RSA Key PEM File sshkey-dsa - SSH-2 DSA Key PEM File sslpem-root - SSL Trusted Root Certificate PEM File sslpem-server - SSL Server Certificate PEM File sslpem-dhweak - SSL DH Weak Encryption Parameter PEM File sslpem-dhstrong - SSL DH Strong Encryption Parameter PEM File cli-banner - CLI Banner File kernel - Kernel File lang-pack - Language Pack File. Ias-users - IAS user file startup-config - Startup Config File backup-config - Backup Config File factory-default-config - Factory Default Config File config-script - Config Script File publickey-image - Public key for image digital signature validation publickey-script - Public key for script digital signature validation Note: SSH Key files can only be downloaded if SSH Server is administratively disabled, and there are no active SSH sessions. Kernel file can be downloaded only on raptor platform and linux operating system. Language pack file is used when NLS localization feature is available.

OBJECT-TYPE

Transfer download start will start an download transfer. The agentTransferDownloadMode object must not be set to xmodem(2), ymodem(3), or zmodem(4) to initiate a transfer via SNMP.

OBJECT-TYPE

Indicates the current status of an download transfer.

OBJECT-TYPE

The type of the serverip address, as defined in the InetAddress MIB. The agentTransferDownloadServerAddress object is intepreted within the context of agentTransferDownloadServerAddressType

OBJECT-TYPE

Transfer download serverip configures the IP address of the server where the file is to be downloaded from.It is valid only when the Transfer Mode is TFTP, SFTP, or SCP. The type of this address is determined by the value of the agentTransferDownloadServerAddressType object. The values for agentTransferDownloadServerAddressType and agentTransferDownloadServerAddress must be consistent.

OBJECT-TYPE

Transfer download image name. Sets the downloaded image as the specified name. Imagename cannot be set to unknown(1) option. When no name is set this object returns unknown(1) by default. Note: Imagename, File Name, File Path, and Server IP Address are applicable only if the Transfer Mode is TFTP, SFTP or SCP.

OBJECT-TYPE

Username applicable to secure download types, i.e., SFTP or SCP and FTP.

OBJECT-TYPE

Password applicable to secure download types, i.e. SFTP or SCP and FTP.

OBJECT-TYPE

Transfer download remote filename configures the file name for the file being transferred from remote system. It can be up to 31 alphanumeric characters.

OBJECT-TYPE

Set the option to perform Digital signature validation of downloading file The following options are supported none - Based on config option do the digital signature validation verify - Verify the digital signature of downloading file noverify - Do not verify the digital signature of downloading file

OBJECT-IDENTITY

OBJECT-TYPE

The image1 software version .

OBJECT-TYPE

The image2 software version.

OBJECT-TYPE

The active image name. image1 or image2.

OBJECT-TYPE

The next active image name. user assigns either image1 or image2.

OBJECT-IDENTITY

OBJECT-TYPE

IfIndex of the mirrored port

OBJECT-TYPE

IfIndex of the probe port

OBJECT-TYPE

Port mirroring mode: enable - enable mirroring mode disable - disable mirroring mode delete - clear MirroredPort and Probe Port configuration

OBJECT-TYPE

This table includes entries for each Port Mirroring session.

OBJECT-TYPE

Provides configuration of a Port Mirroring session specifying the destination port, and the source Port Mask, providing a many-to-one mapping.

OBJECT-TYPE

The Session number of this mirroring entry. The number of sessions is fixed, and is platform dependant.

OBJECT-TYPE

The port which traffic from the mirrored ports will be sent to.

OBJECT-TYPE

The ports from which traffic will be sent to the destination port. The destination port can not be included in this list of ports.

OBJECT-TYPE

The status of this port mirroring session. enable(1) - This session is active and all traffic from the source ports will be mirrored to the destination port. disable(2) - This session is not active. delete(3) - Remove the configuration for this Session

OBJECT-TYPE

The vlan from which traffic will be sent to the destination port.

OBJECT-TYPE

The remote vlan from which traffic will be sent to the destination port.

OBJECT-TYPE

The VLAN that forwards the network traffic to the destination switch. NOTE: In order to set value for the object, need to set values for agentPortMirrorRemoteDestinationVlan and agentPortMirrorReflectorPort objects simultaneously.

OBJECT-TYPE

The port which traffic from the mirrored ports will be sent to in case of destination being remote VLAN. NOTE: In order to set value for the object, need to set values for agentPortMirrorRemoteDestinationVlan and agentPortMirrorReflectorPort objects simultaneously.

OBJECT-TYPE

The IP access-list number attached to the port mirroring session.

OBJECT-TYPE

The MAC access-list number attached to the port mirroring session.

OBJECT-TYPE

This table includes entries for each source port's direction of port mirroring.

OBJECT-TYPE

Provides configuration of a Port Mirroring direction specifying the session of the port mirroring and source port

OBJECT-TYPE

The port from which traffic will be sent to the destination port. This port should be a source port in the corresponding session

OBJECT-TYPE

The direction of the data to be mirrored on this source port. tx(1) - The data that is transmitted from the source port. rx(2) - The data that is received on the source port. txrx(3) - The data that is transmitted/received from/on the source port

OBJECT-TYPE

The VLAN configured as RSPAN VLAN.

OBJECT-TYPE

A table of the RSPAN VLAN config entries

OBJECT-TYPE

RSPAN VLAN config entry

OBJECT-TYPE

The VLAN which is configured as a remote-span VLAN.

OBJECT-TYPE

The status of this entry. active(1) - the VLAN is configured as a remote-span VLAN createAndGo(4) - add the VLAN as a remote-span VLAN destroy(6) - remove the VLAN from the list of Remote-span VLAN. RSPAN VLAN cannot be removed or changed while it is used with a Monitor session.

OBJECT-TYPE

This table provides 802.3ad link aggregation information for each physical port that is not available through the standard MIB.

OBJECT-TYPE

Information about a table entry. The agentDot3adAggPort identifies the external interface number of the port.

OBJECT-TYPE

ifIndex of this physical port

OBJECT-TYPE

Enable/disable 802.3ad LACP on this port

OBJECT-TYPE

A table of the switch's physical port config entries

OBJECT-TYPE

Switch's physical port config entry

OBJECT-TYPE

The port number of this port.

OBJECT-TYPE

The switch's Port IfIndex

OBJECT-TYPE

The switch's Port Type

OBJECT-TYPE

The switch's Port Spanning Tree Protocol Mode STP mode values are: dot1d (the default) fast, indicates you want to use the fast spanning tree mode off, indicates the STP mode is turned off for a particular port This object is only supported when the Dot1d Protocol is enabled.

OBJECT-TYPE

The switch's Port Spanning Tree Protocol State. This object is only supported when the Dot1d Protocol is enabled.

OBJECT-TYPE

The switch's Port Admin Mode

OBJECT-TYPE

The switch's Port Speed Mode. This is the configured physical mode. This object is read-only for gigabit ports

OBJECT-TYPE

The switch's Port Physical Speed Status. This is the current actual speed.

OBJECT-TYPE

If enabled, link up and link down traps will be sent for this port.

OBJECT-TYPE

clear stats for this port only

OBJECT-TYPE

This object identifies the default administrative port type, to be used in conjunction with the operational port type denoted by agentPortType. This object represents the administratively-configured type of the MAU. If auto-negotiation is not enabled or is not implemented for this MAU, the value of this object determines the operational type of the MAU. In this case, a set to this object will force the MAU into the specified operating mode. If auto-negotiation is implemented and enabled for this MAU, the operational type of the MAU is determined by auto-negotiation, and the value of this object denotes the type to which the MAU will automatically revert if/when auto-negotiation is later disabled. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType1000BaseTFD dot3MauType1000BaseXFD dot3MauType10GigBaseX agentPortType40GigBaseX

OBJECT-TYPE

This object identifies the port type. An initial set of MAU types are defined in RFC 2668. The assignment of OBJECT IDENTIFIERs to new types of MAUs is managed by the IANA. If the MAU type is unknown, either a private object identifier, if one exists, or the object identifier unknownMauType OBJECT IDENTIFIER ::= { 0 0 } is returned. Note that unknownMauType is a syntactically valid object identifier, and any conformant implementation of ASN.1 and the BER must be able to generate and recognize this value. This object represents the operational type of the MAU, as determined by either (1) the result of the auto-negotiation function or (2) if auto-negotiation is not enabled or is not implemented for this MAU, by the value of the object agentPortDefaultType, or (3) for the GigE card a value determined by the GBIC connected to the card. In case (2), a set to the object agentPortDefaultType will force the MAU into the new operating mode. The valid values for this object are: dot3MauType10BaseTHD dot3MauType10BaseTFD dot3MauType100BaseTXHD dot3MauType100BaseTXFD dot3MauType100BaseFXFD dot3MauType1000BaseSXFD dot3MauType1000BaseTFD dot3MauType1000BaseXFD dot3MauType10GigBaseX agentPortType40GigBaseX

OBJECT-TYPE

This object identifies the administration status of auto negotiation for this port.

OBJECT-TYPE

Config flowcontrol allows you to enable or disable 802.3x flow control for this port. This value applies to only full-duplex mode ports. Enabling symmetric flow control allows the port to send and receive pause frames. Enabling asymmetric flow control allows the port to receive pause frames but it will not transmit pause frames.

OBJECT-TYPE

Controls the Double Vlan Tag mode on this port.

OBJECT-TYPE

Configures the Double Vlan Tag Ethertype for this port. If this object is supported, ethertype cannot be configured globally for the switch. Commonly used are the Ethertypes for vman tags (34984, or 0x88A8) and dot1q tags (33024, or 0x8100).

OBJECT-TYPE

Configures the Customer ID for the Double Vlan Tag for this port.

OBJECT-TYPE

This object identifies the largest value that can be configured for agentPortMaxFrameSize

OBJECT-TYPE

This object identifies the currently configured maximum frame size value for this port. The maximmum value that this object can be set to is the value of agentPortMaxFrameSizeLimit. For Ethernet ports which support 802.1Q vlan tagging, the minimum value that this object can be set to is 1522

OBJECT-TYPE

If enabled, broadcast storm recovery will function on this port. When you specify Enable for Broadcast Storm Recovery and the broadcast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the broadcast traffic.

OBJECT-TYPE

Configures the broadcast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate.

OBJECT-TYPE

If enabled, multicast storm recovery will function on this port. When you specify Enable for Multicast Storm Recovery and the multicast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the multicast traffic.

OBJECT-TYPE

Configures the multicast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate.

OBJECT-TYPE

If enabled, unicast storm recovery will function on this port. When you specify Enable for Unicast Storm Recovery and the unknown unicast traffic on this Ethernet port exceeds the configured threshold, the switch blocks (discards) the unknown unicast traffic.

OBJECT-TYPE

Configures the unicast storm recovery threshold for this port as a percentage of port speed or as an absolute pps rate.

OBJECT-TYPE

Configures the units of the threshold value to percentage of port speed or absolute packets per second.

OBJECT-TYPE

Configures the units of the threshold value to percentage of port speed or absolute packets per second.

OBJECT-TYPE

Configures the units of the threshold value to percentage of port speed or absolute packets per second.

OBJECT-TYPE

Describes and Configures the Port Voice VLAN Mode. This object can only be set to disable(5).

OBJECT-TYPE

Describes and Configures the Port Voice VLAN ID if the Voice Vlan Mode is Vlan ID.

OBJECT-TYPE

Describes and Configures the Port Voice VLAN Priority if the Voice Vlan Mode is dot1p. A value of 255 indicates that the priority is not configured.

OBJECT-TYPE

Describes and Configures the Port Voice VLAN Data Priority Mode.

OBJECT-TYPE

Describes the Port Voice VLAN Operational Status.

OBJECT-TYPE

Describes and Configures the Port Voice VLAN tagging mode.

OBJECT-TYPE

Describes and Configures the Port Voice VLAN None mode.

OBJECT-TYPE

Describes and Configures the Port Voice VLAN DSCP value.

OBJECT-TYPE

Describes and Configures the Port Voice VLAN Authentication mode. Disable means authentication not required for voice devices when dot1x is enabled.

OBJECT-TYPE

This object identifies operational status of the flow control per port.

OBJECT-TYPE

OBJECT-IDENTITY

OBJECT-TYPE

Set to non-empty string to create a Protocol-Based VLAN group.

OBJECT-TYPE

A table of the switch's Protocol-based VLAN entries

OBJECT-TYPE

Switch's Protocol-based VLAN entry

OBJECT-TYPE

Group identifier of the Protocol-based VLAN entry.

OBJECT-TYPE

Group name of the Protocol-based VLAN entry.

OBJECT-TYPE

VLAN associated with the Protocol-based VLAN entry. Set to 0 to remove.

OBJECT-TYPE

The status of the IP protocol association with the Protocol-based VLAN entry.

OBJECT-TYPE

The status of the ARP protocol association with the Protocol-based VLAN entry.

OBJECT-TYPE

The status of the IPX protocol association with the Protocol-based VLAN entry.

OBJECT-TYPE

The status of the Protocol-based VLAN entry. active(1) - this entry is active createAndGo(4) - used to create a new entry destroy(6) - remove this entry

OBJECT-TYPE

A table of the switch's physical port config entries

OBJECT-TYPE

Switch's physical port config entry

OBJECT-TYPE

The interface number of this instance.

OBJECT-TYPE

The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group

OBJECT-TYPE

A table of the switch's physical port config entries

OBJECT-TYPE

Switch's physical port config entry

OBJECT-TYPE

The protocol ID of this instance. The value for IP is 2048 (0x0800), ARP is 2054 (0x0806) and IPX is 33079 (0x8137). Other protocol Ids in the range 1536 to 65535 can also be configured.

OBJECT-TYPE

The status of this entry. active(1) - the port is associated with this group createAndGo(4) - add the port to this group createAndWait(5) - add the port to this group destroy(6) - remove the port from this group

OBJECT-IDENTITY

OBJECT-TYPE

The MST configuration digest key.

OBJECT-TYPE

The MST configuration format selector. A value other than 0 (zero) indicates non-support for the IEEE 802.1s standard.

OBJECT-TYPE

The MST configuration name of at most 32 characters.

OBJECT-TYPE

The MST configuration revision. The default value is 1.

OBJECT-TYPE

The MST configuration force protocol version. The default version is dot1s.

OBJECT-TYPE

The spanning tree operational status. enable(1) - enables spanning tree operational status on the switch. disable(2) - disables spanning tree operational status on the switch. The default status is disabled.

OBJECT-TYPE

The spanning tree BPDU Guard Mode. enable(1) - enables BPDU Guard Mode on the switch. disable(2) - disables BPDU Guard Mode on the switch. The default status is disabled.

OBJECT-TYPE

The spanning tree BPDU Filter Mode, it enables BPDU Filter on all edge ports. enable(1) - enables BPDU Filter Mode on the switch. disable(2) - disables BPDU Filter Mode on the switch. The default status is disabled.

OBJECT-TYPE

STP port table.

OBJECT-TYPE

STP port entry.

OBJECT-TYPE

The administrative STP state for the port. enable(1) - enables STP on the port. disable(2) - disables STP on the port. The default port STP state is enabled for the first 4095 ports and disabled for any ports beyond.

OBJECT-TYPE

The MSTP BPDUs received on a specific port.

OBJECT-TYPE

The MSTP BPDUs sent from a specific port.

OBJECT-TYPE

The RSTP BPDUs received on a specific port.

OBJECT-TYPE

The RSTP BPDUs sent from a specific port.

OBJECT-TYPE

The STP BPDUs received on a specific port.

OBJECT-TYPE

The STP BPDUs sent from a specific port.

OBJECT-TYPE

Time since port was reset. It is displayed in days, hours, minutes, and seconds.

OBJECT-TYPE

Force the specified port to transmit RSTP or MSTP BPDU's. Supported values: false(0) - BPDUs are not to be transmitted. true(1) - BPDUs are to be transmitted A non-zero value indicates that BPDUs are to be sent on the specified port.

OBJECT-TYPE

The spanning-tree hello time for the specified port.

OBJECT-IDENTITY

OBJECT-TYPE

The MSTP root port hello time for the CIST.

OBJECT-TYPE

The MSTP root port max age for the CIST.

OBJECT-TYPE

The MSTP regional root identifier for the CIST.

OBJECT-TYPE

The MSTP regional root path cost for the CIST.

OBJECT-TYPE

The MSTP root port forward delay for the CIST.

OBJECT-TYPE

The MSTP bridge forward delay for the CIST. The default value is 15.

OBJECT-TYPE

The MSTP bridge hello time for the CIST. The default value is 2. According to IEEE 802.1Q-REV 2005 updating hello time is disallowed

OBJECT-TYPE

The MSTP bridge hold time for the CIST.

OBJECT-TYPE

The MSTP bridge max age for the CIST. The default value is 20.

OBJECT-TYPE

The MSTP bridge max hops for the CIST. The default value is 20.

OBJECT-TYPE

The MSTP bridge priority for the CIST. The default value is 32768.

OBJECT-TYPE

The MSTP bridge hold count for the CIST. This command sets the value of maximum bpdus that a bridge is allowed to send within a hello time window. The default value is 6.

OBJECT-TYPE

CIST port table.

OBJECT-TYPE

CIST port entry.

OBJECT-TYPE

The MSTP operational status of a specific port for the CIST.

OBJECT-TYPE

The MSTP operational point to point mac of a specific port for the CIST.

OBJECT-TYPE

The MSTP topology change acknowledge for a specific port in the CIST.

OBJECT-TYPE

The administrative state of a specific port in CIST. enable(1) - enables the port. disable(2) - disables the port. The default port state is disabled.

OBJECT-TYPE

The MSTP forwarding state of a specific port in CIST.

OBJECT-TYPE

The MSTP port identifier of a specific port in CIST.

OBJECT-TYPE

The MSTP port path cost in CIST. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.

OBJECT-TYPE

The MSTP port priority in CIST. The priority is in the increments of 16. The default value is 128.

OBJECT-TYPE

The MSTP designated bridge ID of a specific port in CIST.

OBJECT-TYPE

The MSTP designated cost of a specific port in CIST.

OBJECT-TYPE

The MSTP designated port ID of a specific port in CIST.

OBJECT-TYPE

The MSTP external port path cost in CIST. The default value varies depending upon the link speed.

OBJECT-TYPE

BPDU Guard Mode effect on the port. enable(1) - BPDU Guard Mode is enabled on the port. disable(2) - BPDU Guard Mode is disabled on the port.

OBJECT-TYPE

This command sets BPDU Filter mode on the port. enable(1) - BPDU Filter Mode is enabled on the port. disable(2) - BPDU Filter Mode is disabled on the port.

OBJECT-TYPE

This command sets BPDU Flood mode on the port. enable(1) - BPDU Flood Mode is enabled on the port. disable(2) - BPDU Flood Mode is disabled on the port.

OBJECT-TYPE

This command sets the auto-edge mode of the port which enables it to become an edge port if it does not see BPDUs for some duration. enable(1) - enables the auto-edge mode for the port. disable(2) - disables the auto-edge mode for the port. The default auto-edge mode is enabled.

OBJECT-TYPE

This command sets a port to discard any superior information received by the port and thus protect against root of the device from changing.The port gets put into discarding state and does not forward any packets. enable(1) - enables the root-guard mode for the port. disable(2) - disables the root-guard mode for the port. The default root-guard mode is disabled.

OBJECT-TYPE

This command restricts the port from propagating any topology change information received through that port. enable(1) - enables the tcn-guard mode for the port. disable(2) - disables the tcn-guard mode for the port. The default tcn-guard mode is disabled.

OBJECT-TYPE

This command enables loop guard on this port. This setting applies to all Spanning Tree instances of which this port is a member. enable(1) - enables the loop guard mode for the port. disable(2) - disables the loop guard mode for the port. The default loop-guard mode is disabled.

OBJECT-TYPE

MST table.

OBJECT-TYPE

MST entry.

OBJECT-TYPE

The MSTP instance ID.

OBJECT-TYPE

The MSTP bridge priority in a specific instance. The priority is in the increments of 4096. The recommended default value is 32768.

OBJECT-TYPE

The MSTP bridge identifier in a specific instance.

OBJECT-TYPE

The MSTP designated root bridge identifier in a specific instance.

OBJECT-TYPE

The MSTP root path cost in a specific instance.

OBJECT-TYPE

The MSTP root port ID in a specific instance.

OBJECT-TYPE

The MSTP time since the last topology change in a specific instance.

OBJECT-TYPE

The MSTP count of topology changes in a specific instance.

OBJECT-TYPE

The MSTP topology change parameter in a specific instance.

OBJECT-TYPE

The MSTP instance status. Supported values: active(1) - valid instance. createAndGo(4) - used to create a new instance. destroy(6) - removes an instance.

OBJECT-TYPE

MST port table.

OBJECT-TYPE

MST port entry.

OBJECT-TYPE

The MSTP forwarding state of a specific port in a specific instance.

OBJECT-TYPE

The MSTP port identifier of a specific port in a specific instance.

OBJECT-TYPE

The MSTP port path cost in a specific instance. The default value will correspond to the recommendation specified in IEEE 802.1s Table 13-2 which varies depending upon link speed.

OBJECT-TYPE

The MSTP port priority in a specific instance. The priority is in the increments of 16. The default value is 128.

OBJECT-TYPE

The MSTP designated bridge ID of a specific port in a specific instance.

OBJECT-TYPE

The MSTP designated cost of a specific port in a specific instance.

OBJECT-TYPE

The MSTP designated port ID of a specific port in a specific instance.

OBJECT-TYPE

The loop inconsistent state of a specific port in a specific instance. This value can only report as true(1) when loop guard is enabled on the port and the port has transitioned from blocking state in this MST instance.

OBJECT-TYPE

The number of times this interface has transitioned into loop inconsistent state.

OBJECT-TYPE

The number of times this interface has transitioned out of loop inconsistent state.

OBJECT-TYPE

MST VLAN table.

OBJECT-TYPE

MST VLAN entry.

OBJECT-TYPE

The association status of an MSTP instance and a VLAN. Supported values: active(1) - valid association between an MSTP instance and a VLAN. createAndGo(4) - used to create a new association between an MSTP instance and a VLAN. destroy(6) - removes the association between an MSTP instance and a VLAN.

OBJECT-IDENTITY

OBJECT-TYPE

The per VLAN spanning tree operational status. enable(1) - enables PVSTP on the switch. disable(2) - disables PVSTP on the switch. The default status is disabled.

OBJECT-TYPE

The per VLAN rapid spanning tree operational status. enable(1) - enables PVRSTP on the switch. disable(2) - disables PVRSTP on the switch. The default status is disabled.

OBJECT-TYPE

Enables or disabled uplink fast feature when switch is in PVST mode. enable(1) - enables UPLINK FAST on the switch. disable(2) - disables UPLINK FAST on the switch. The default status is disabled.

OBJECT-TYPE

Enables or disabled backbone fast feature when switch is in PVST mode. enable(1) - enables BACKBONE FAST on the switch. disable(2) - disables BACKBONE FAST on the switch. The default status is disabled.

OBJECT-TYPE

PVRSTP table containing PVRSTP per vlan entries.

OBJECT-TYPE

PVRSTP vlan entry attributes.

OBJECT-TYPE

Index to PVRSTP vlan entry in PVRSTP vlan table.

OBJECT-TYPE

The PVRSTP primary or secondary root for the VLAN instance.

OBJECT-TYPE

The PVRSTP hello time for the VLAN instance.

OBJECT-TYPE

The PVRSTP forward delay for the VLAN instance.

OBJECT-TYPE

The PVRSTP max age for the VLAN instance.

OBJECT-TYPE

PVRSTP table containing PVRSTP per port per vlan entries.

OBJECT-TYPE

PVRSTP port entry per vlan attributes.

OBJECT-TYPE

Port index to PVRSTP port entry in PVRSTP port vlan table.

OBJECT-TYPE

Vlan index to PVRSTP port entry in PVRSTP port vlan table.

OBJECT-TYPE

PVRSTP port vlan priority is in the range of 0 to 240. Port priority value should be a multiple of 16.

OBJECT-TYPE

PVRSTP port vlan cost is in the range of 0 to 200000000 ,for 0 its Auto.

OBJECT-IDENTITY

OBJECT-TYPE

Authentication List Create If set to a non empty string, creates a new Authentication List for configuration.

OBJECT-TYPE

Authentication List table.

OBJECT-TYPE

Authentication List entry.

OBJECT-TYPE

Authentication List Index Unique number used for indexing into this table.

OBJECT-TYPE

Authentication List Name Unique name used to identify the Authentication List from other tables.

OBJECT-TYPE

Authentication List Method 1 Configures the first authentication method to use when this list is specified.

OBJECT-TYPE

Authentication List Method 2 Configures the second authentication method to use when this list is specified.

OBJECT-TYPE

Authentication List Method 3 Configures the third authentication method to use when this list is specified.

OBJECT-TYPE

The status of the Authentication List. Supported values: active(1) - indicates a valid Authenticaiton List destroy(6) - removes the Authentication List.

OBJECT-TYPE

Authentication List Method 4 Configures the fourth authentication method to use when this list is specified.

OBJECT-TYPE

Authentication List Method 5 Configures the fifth authentication method to use when this list is specified.

OBJECT-TYPE

Default Authentication List This object configures which authentication list to use for users which do not have an Authentication List configured. The list must be configured before setting.

OBJECT-TYPE

User Authentication Config Table

OBJECT-TYPE

User Authentication Config Entry

OBJECT-TYPE

User Authentication List This object configures which authentication list to use for this user. The list must be configured before setting.

OBJECT-TYPE

User Port Config Table

OBJECT-TYPE

User Port Config Entry

OBJECT-TYPE

User Port Port Security This object configures which ports the user has access to. Ports are indexed based on dot1dBasePort entries in dot1dBasePortTable.

OBJECT-IDENTITY

OBJECT-TYPE

A table that contains information about the 802.1p priority mapping to traffic class priority queue for every physical port.

OBJECT-TYPE

A 802.1p priority mapped to a traffic class priority queue.

OBJECT-TYPE

The Priority value determined for the received frame. This value is equivalent to the priority indicated in the tagged frame received, or one of the evaluated priorities, determined according to the media-type. For untagged frames received from Ethernet media, this value is equal to the dot1dPortDefaultUserPriority value for the ingress port.

OBJECT-TYPE

Traffic class priority queue the received frame is mapped to.

OBJECT-IDENTITY

OBJECT-TYPE

Configures the HTTP server admin mode

OBJECT-TYPE

Configures the use of the Java interface through Web connections.

OBJECT-TYPE

Configures the maximum number of allowable HTTP sessions. The default value is 16.

OBJECT-TYPE

Configures the hard timeout for HTTP sessions in hours. The default value is 24 hours.

OBJECT-TYPE

Configures the soft (activity) timeout for HTTP sessions in minutes. The default value is 5 minutes.

OBJECT-TYPE

Get/Set the TCP port number that the HTTP server listens to for incoming requests. The port number is an integer value from 1025 to 65535. Before setting this object, check your system (e.g. using 'netstat') to make sure the desired port number is not currently being used by any other service. The default value for this object is 80. Note that existing HTTP login sessions are closed whenever this object value is changed. All new HTTP sessions must be established using the new port number.

OBJECT-IDENTITY

OBJECT-TYPE

Enable/Disable Autoinstall on device.

OBJECT-TYPE

Enable/Disable Auto Save of downloaded configuration on device.

OBJECT-TYPE

Sets number of unicast TFTP attempts for configuration file.

OBJECT-TYPE

Display current Autoinstall status on device.

OBJECT-TYPE

Enable/Disable Auto Reboot after succesfull image update on device.

OBJECT-TYPE

Enable/Disable Autoinstall operational mode on device.

OBJECT-IDENTITY

OBJECT-TYPE

ExecAccounting List Create if set to a non empty string, creates a new ExecAccounting List for configuration.

OBJECT-TYPE

ExecAccounting Method List table.

OBJECT-TYPE

ExecAccounting Method List Entry.

OBJECT-TYPE

ExecAccounting List Index Unique number used for indexing into this table.

OBJECT-TYPE

Unique name used to identify the ExecAccounting List from other tables.

OBJECT-TYPE

ExecAccounting Method Type Configures the method type to use when this ExecAccounting list is specified.

OBJECT-TYPE

ExecAccounting List Method 1 Configures the authentication method to use when this list is specified.

OBJECT-TYPE

ExecAccounting List Method 2 Configures the authentication method to use when this list is specified.

OBJECT-TYPE

The status of the ExecAccounting List. Supported values: active(1) - indicates a valid ExecAccounting List destroy(6) - removes the ExecAccounting List.

OBJECT-IDENTITY

OBJECT-TYPE

CmdsAccounting List Create if set to a non empty string, creates a new CmdsAccounting List for configuration.

OBJECT-TYPE

CmdsAccounting Method List table.

OBJECT-TYPE

CmdsAccounting Method List Entry.

OBJECT-TYPE

CmdsAccounting List Index Unique number used for indexing into this table.

OBJECT-TYPE

Unique name used to identify the CmdsAccounting List from other tables.

OBJECT-TYPE

CmdsAccounting Method Type Configures the method type to use when this CmdsAccounting list is specified.

OBJECT-TYPE

CmdsAccounting List Method 1 Configures the authentication method to use when this list is specified.

OBJECT-TYPE

The status of the CmdsAccounting List. Supported values: active(1) - indicates a valid CmdsAccounting List destroy(6) - removes the CmdsAccounting List.

OBJECT-IDENTITY

OBJECT-TYPE

Command Authorization List Create. If set to a non empty string, creates a new Command Authorization List for configuration. List name must contain Alphanumeric characters including '-', '_', ' '.

OBJECT-TYPE

Command Authorization Method List table.

OBJECT-TYPE

Command Authorization Method List Entry.

OBJECT-TYPE

Command Authorization List Index Unique number used for indexing into this table.

OBJECT-TYPE

Command Authorization List Name Unique name used to identify the Command Authorization List from other tables.

OBJECT-TYPE

The status of the CmdsAuthorization List. Supported values: active(1) - indicates a valid CmdsAuthorization List destroy(6) - removes the CmdsAuthorization List.

OBJECT-TYPE

Command Authorization List Method1 Configures the Command Authorization method to use when this list is specified.

OBJECT-TYPE

Command Authorization List Method2 Configures the Command Authorization method to use when this list is specified.

OBJECT-TYPE

Command Authorization List Method2 Configures the Command Authorization method to use when this list is specified.

OBJECT-IDENTITY

OBJECT-TYPE

Exec Authorization List Create. If set to a non empty string, creates a new Exec Authorization List for configuration. List name must contain Alphanumeric characters including '-', '_', ' '.

OBJECT-TYPE

Exec Authorization Method List table.

OBJECT-TYPE

Exec Authorization Method List Entry.

OBJECT-TYPE

Exec Authorization List Index Unique number used for indexing into this table.

OBJECT-TYPE

Exec Authorization List Name Unique name used to identify the Exec Authorization List from other tables.

OBJECT-TYPE

The status of the ExecAuthorization List. Supported values: active(1) - indicates a valid ExecAuthorization List destroy(6) - removes the ExecAuthorization List.

OBJECT-TYPE

Exec Authorization List Method1 Configures the Exec Authorization method to use when this list is specified.

OBJECT-TYPE

Exec Authorization List Method2 Configures the Exec Authorization method to use when this list is specified.

OBJECT-TYPE

Exec Authorization List Method3 Configures the Exec Authorization method to use when this list is specified.

OBJECT-TYPE

Exec Authorization List Method4 Configures the Exec Authorization method to use when this list is specified.

OBJECT-IDENTITY

OBJECT-TYPE

The Mbuf utilization rising threshold in percentage. A single notification (rising event) is generated when the total Mbuf utilization exceeds this threshold. After a rising event is generated, another such event will not be generated until the total Mbuf utilization falls below the agentSwitchMbufFallingThreshold and then exceeds the agentSwitchMbufRisingThreshold.

OBJECT-TYPE

The Mbuf utilization falling threshold in percentage. A single notification (falling event) is generated when the total Mbuf utilization falls below this threshold. After a falling event is generated, another such event will not be generated until the total Mbuf utilization exceeds the agentSwitchMbufRisingThreshold and then falls below the agentSwitchMbufFallingThreshold.

OBJECT-TYPE

Severity level while notification is generated for rising and falling threshold.

OBJECT-IDENTITY

OBJECT-TYPE

To configure the digital signature verify option for the downloading image and config files. The selected option is stored in config data. The following options are supported: noverify - no digital signature verification of image or config script file image - digital signature verification of image only config - digital signature verification of config script only all - digital signature verification of image and config script file

OBJECT-IDENTITY

OBJECT-TYPE

enable(1) will initiate an configuration save to nvram. Status is returned by the object agentSaveConfigStatus.

OBJECT-TYPE

clear config to factory defaults

OBJECT-TYPE

close all telnet sessions

OBJECT-TYPE

reset passwords

OBJECT-TYPE

clear all port statistics

OBJECT-TYPE

clear all switch statistics

OBJECT-TYPE

clear trap log

OBJECT-TYPE

clear vlan entries

OBJECT-TYPE

Resets the switch. This object is not valid for stacking platforms.

OBJECT-TYPE

Indicates the current status of an save configuration request.

OBJECT-TYPE

Erase the text-based configuration named startup-config stored in non-volatile memory.On read returns 0.

OBJECT-TYPE

Erase the text-based configuration file named factory-defaults stored in non-volatile memory.On read returns 0.

OBJECT-IDENTITY

OBJECT-TYPE

Status of the Virtual Cable Tester active(1) - cable testing is in progress. Set to this value to start the test. success(2) - A successful test was performed. Cannot be set. failure(3) - A failure was encountered during the test. Cannot be set. uninitialized(4) - No test has been performed yet. Cannot be set.

OBJECT-TYPE

Determines on which port to perform the cable test. Limited to copper based ports.

OBJECT-TYPE

Indicates the results of the Cable Test. normal(1) - The cable is working correctly. open(2) - The cable is disconnected or there is a faulty connector. short(3) - There is an electrical short in the cable. unknown(4) - No test has been performed yet, or a test is currently in progress.

OBJECT-TYPE

The estimated length of the cable in meters. This value indicates the shortest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.

OBJECT-TYPE

The estimated length of the cable in meters. This value indicates the longest length estimated. This object will return 0 if agentCableTesterStatus is not success(2) or the cable length is unknown.

OBJECT-TYPE

The estimated distance in meters from the end of the cable to the failure location. This object will return 0 if agentCableTesterStatus is not success(2).