ENTERASYS-CONVERGENCE-END-POINT-MIB
- Registered at
- 1.3.6.1.4.1.5624.1.2.40
- Last updated
- 2005-11-18 13:25
- Organization
- Enterasys Networks, Inc
- Revisions
- 2005-11-18 13:25, 2005-10-19 15:49, 2005-08-16 12:33, 2005-06-16 14:27, 2005-03-31 16:10, 2003-11-05 19:42
- Namespace
- enterasys
- Source file
ENTERASYS-CONVERGENCE-END-POINT-MIB- Digest
sha256:36bdaece59ef849d540aff9256b5846fa2ab8c6db734b8456e8b5010e8e970c9
Description
This MIB module defines a portion of the SNMP MIB under Enterasys Networks enterprise OID pertaining to Convergence End Point management.
Contact
Postal: Enterasys Networks 50 Minuteman Rd. Andover, MA 01810-1008 USA Phone: +1 978 684 1000 E-mail: support@enterasys.com WWW: http://www.enterasys.com
Imports
| From | Symbols |
|---|---|
| ENTERASYS-MIB-NAMES | etsysModules |
| IF-MIB | InterfaceIndex, ifIndex |
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
| P-BRIDGE-MIB | EnabledStatus |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DateAndTime, DisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
BRIDGE-MIB ENTERASYS-CONVERGENCE-END-POINT-MIB ENTERASYS-MIB-NAMES IANAifType-MIB IF-MIB INET-ADDRESS-MIB P-BRIDGE-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ConvEndPointTypes TEXTUAL-CONVENTION Supported Convergence End Point products. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| etsysConvEndPointObjects OBJECT-IDENTITY | 1.3.6.1.4.1.5624.1.2.40.1 | |||
| etsysConvEndPointConfig OBJECT-IDENTITY | 1.3.6.1.4.1.5624.1.2.40.1.1 | |||
| etsysConvEndPointGlobalConfigEnable OBJECT-TYPE When set to enabled(1) this object activates the current Convergence End Point configuration. When set to disabled(2) this MIB SHALL be configurable, but MUST NOT be applied, all entries will be removed from the etsysConvEndPointConnMacTable and the etsysConvEndPointConnPortTable, and any policies that have been changed as a result of End Point detection will revert to their default states. Maintaining the value of this object across agent reboots is REQUIRED. | 1.3.6.1.4.1.5624.1.2.40.1.1.1 | EnabledStatus | read-write | current |
| etsysConvEndPointGlobalConfigTable OBJECT-TYPE This table represents all Convergence End Point types supported by this entity, and provides a default policy profile for each Convergence End Point type. | 1.3.6.1.4.1.5624.1.2.40.1.1.2 | not-accessible | current | |
| etsysConvEndPointGlobalConfigEntry OBJECT-TYPE Defines the default policy to be applied when this type of Convergence End Point is detected or discovered. | 1.3.6.1.4.1.5624.1.2.40.1.1.2.1 | not-accessible | current | |
| etsysConvEndPointGlobalEndPointType OBJECT-TYPE The Convergence End Point type. The value of this object is limited to a single enumerated bit in the ConvEndPointTypes textual convention. | 1.3.6.1.4.1.5624.1.2.40.1.1.2.1.1 | ConvEndPointTypes | not-accessible | current |
| etsysConvEndPointGlobalDefaultPolicyIndex OBJECT-TYPE The policy that should be applied for this type of Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If no such policy index exists, then no policy will be applied when this type of Convergence End Point is detected or discovered. The value zero is not a valid etsysPolicyProfileIndex, so zero indicates that no policy should be applied. Maintaining the value of this object across system reboots is REQUIRED. | 1.3.6.1.4.1.5624.1.2.40.1.1.2.1.2 | Integer32 (0 | 1..65535) | read-write | current |
| etsysConvEndPointProtocolConfigTable OBJECT-TYPE This table provides control of Convergence End Point detection and discovery on a per interface and per Convergence End Point type basis. Maintaining the values of this table across system reboots is REQUIRED. | 1.3.6.1.4.1.5624.1.2.40.1.1.3 | not-accessible | current | |
| etsysConvEndPointProtocolConfigEntry OBJECT-TYPE The current Convergence End Point detection and discovery status for an interface. | 1.3.6.1.4.1.5624.1.2.40.1.1.3.1 | not-accessible | current | |
| etsysConvEndPointProtocolEndPointType OBJECT-TYPE The Convergence End Point type. | 1.3.6.1.4.1.5624.1.2.40.1.1.3.1.1 | ConvEndPointTypes | not-accessible | current |
| etsysConvEndPointProtocolEnable OBJECT-TYPE When set to enabled(1), Convergence End Point detection and discovery will be enabled on this interface for the Convergence End Point type specified. When set to disabled(2), the Convergence End Points that have been discovered or detected on this interface of the type specified will be removed from the etsysConvEndPointConnMacTable and the etsysConvEndPointConnPortTable. After all of the End Points have been removed from an interface the policy on that interface will revert to its default state. | 1.3.6.1.4.1.5624.1.2.40.1.1.3.1.2 | EnabledStatus | read-write | current |
| etsysConvEndPointStatus OBJECT-IDENTITY | 1.3.6.1.4.1.5624.1.2.40.1.2 | |||
| etsysConvEndPointConnMacTable OBJECT-TYPE This table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object across system reboots is NOT REQUIRED. | 1.3.6.1.4.1.5624.1.2.40.1.2.1 | not-accessible | deprecated | |
| etsysConvEndPointConnMacEntry OBJECT-TYPE Information about an individual Convergence End Point. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1 | not-accessible | deprecated | |
| etsysConvEndPointConnMacMacAddress OBJECT-TYPE The MAC address of this Convergence End Point. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.1 | MacAddress | not-accessible | deprecated |
| etsysConvEndPointConnMacPortNumber OBJECT-TYPE The interface on which this Convergence End Point was detected or discovered. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.2 | InterfaceIndex | read-only | deprecated |
| etsysConvEndPointConnMacEndPointType OBJECT-TYPE The type of Convergence End Point described by this row. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.3 | ConvEndPointTypes | read-only | deprecated |
| etsysConvEndPointConnMacPolicyIndex OBJECT-TYPE The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a zero MUST be returned. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.4 | Integer32 | read-only | deprecated |
| etsysConvEndPointConnMacDiscoveryTime OBJECT-TYPE The time and date that this Convergence End Point was detected or discovered. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.5 | DateAndTime | read-only | deprecated |
| etsysConvEndPointConnMacFirmwareVersion OBJECT-TYPE This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.6 | SnmpAdminString (SIZE(0..32)) | read-only | deprecated |
| etsysConvEndPointConnMacInetAddressType OBJECT-TYPE The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.7 | InetAddressType | read-only | deprecated |
| etsysConvEndPointConnMacInetAddress OBJECT-TYPE The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string. | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.8 | InetAddress | read-only | deprecated |
| etsysConvEndPointConnPortTable OBJECT-TYPE This table provides a mapping from the entities interfaces to discovered Convergence End Points. Maintaining the value of this object across system reboots is NOT REQUIRED. | 1.3.6.1.4.1.5624.1.2.40.1.2.2 | not-accessible | current | |
| etsysConvEndPointConnPortEntry OBJECT-TYPE Information about an individual Convergence End Point. | 1.3.6.1.4.1.5624.1.2.40.1.2.2.1 | not-accessible | current | |
| etsysConvEndPointConnPortMacAddress OBJECT-TYPE The MAC address of the discovered or detected Convergence End Point. | 1.3.6.1.4.1.5624.1.2.40.1.2.2.1.1 | MacAddress | read-only | current |
| etsysCEPConnMacTable OBJECT-TYPE This table provides information on each of the Convergence End Points that has been discovered or detected by this entity. Maintaining the value of this object across system reboots is NOT REQUIRED. | 1.3.6.1.4.1.5624.1.2.40.1.2.3 | not-accessible | current | |
| etsysCEPConnMacEntry OBJECT-TYPE Information about an individual Convergence End Point (CEP). | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1 | not-accessible | current | |
| etsysCEPConnMacEndPointType OBJECT-TYPE The type of Convergence End Point described by this row. | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.1 | ConvEndPointTypes | read-only | current |
| etsysCEPConnMacPolicyIndex OBJECT-TYPE The policy applied for this Convergence End Point. This value is an etsysPolicyProfileIndex as defined in the ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does not currently exist, or never did exist, then a zero MUST be returned. | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.2 | Integer32 (0 | 1..65535) | read-only | current |
| etsysCEPConnMacDiscoveryTime OBJECT-TYPE The time and date that this Convergence End Point was detected or discovered. | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.3 | DateAndTime | read-only | current |
| etsysCEPConnMacFirmwareVersion OBJECT-TYPE This is the firmware version of the discovered Convergence End Point. If this information is not available via the detection protocol then a zero length string MUST be returned. | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.4 | SnmpAdminString (SIZE(0..32)) | read-only | current |
| etsysCEPConnMacInetAddressType OBJECT-TYPE The address type of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return 'unknown'. | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.5 | InetAddressType | read-only | current |
| etsysCEPConnMacInetAddress OBJECT-TYPE The address of the discovered or detected Convergence End Point. If the address is unknown, then this object MUST return a zero length string. | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.6 | InetAddress | read-only | current |
| etsysConvEndPointDetection OBJECT-IDENTITY | 1.3.6.1.4.1.5624.1.2.40.1.3 | |||
| etsysConvEndPointDetectionMaxEntries OBJECT-TYPE This value represents the maximum number of entries allowed in the etsysConvEndPointDetectionTable. | 1.3.6.1.4.1.5624.1.2.40.1.3.1 | Integer32 | read-only | current |
| etsysConvEndPointDetectionTable OBJECT-TYPE A table that describes the IP address and IP port based Convergence End Point detection parameters. Packets on interfaces that are configured to detect End Points, via the etsysConvEndPointProtocolConfigTable, that are defined in this table are inspected to determine if a Convergence End Point exists on that interface. Rules applying to Convergence End Point types that are configured for detection are evaluated according to the following: 1. If etsysConvEndPointDetectionProtocol does not have any bits set, this indicates that the port based detection should not be performed, proceed to step 2. Otherwise the value in etsysConvEndPointDetectionProtocol is evaluated against the protocol field in the IP header, if it is of a, or the, type specified then the destination port must be between the values of etsysConvEndPointDetectionPortLow and etsysConvEndPointDetectionPortHigh, inclusive. 2. If the etsysConvEndPointDetectionAddr is null, this indicates that no detection address check should be performed, consider the End Point detected. Otherwise the value the of etsysConvEndPointDetectionAddr will be masked with the value of etsysConvEndPointDetectionAddrMask, via a bitwise AND operation, and this value will be compared with the destination IP address that has also been masked with the value of etsysConvEndPointDetectionAddrMask, via a bitwise AND operation, if they are equal then consider the End Point detected. If there are no rows in this table that are in the active state then the following pseudo entries describe the behavior of the IP based Convergence End Point detection. EndPointType siemens Protocol { { udp, tcp } } PortLow 4060 PortHigh 4060 AddrType unknown Addr '' AddrMaskType unknown AddrMask '' EndPointType h323 Protocol { { udp, tcp } } PortLow 1718 PortHigh 1720 AddrType ipv4 Addr '224.0.1.41' AddrMaskType ipv4 AddrMask '255.255.255.255' EndPointType sip Protocol { { udp, tcp } } PortLow 5060 PortHigh 5060 AddrType ipv4 Addr '224.0.1.75' AddrMaskType ipv4 AddrMask '255.255.255.255' If one or more entries in this table are active the active entries will define the IP based detection behavior in its entirety. Maintaining entries in this table across system reboots is REQUIRED for entries with an etsysConvEndPointDetectionRowStatus value of active(1). | 1.3.6.1.4.1.5624.1.2.40.1.3.2 | not-accessible | current | |
| etsysConvEndPointDetectionEntry OBJECT-TYPE Each entry represents a describes parameters for detecting a Convergence End Point. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1 | not-accessible | current | |
| etsysConvEndPointDetectionRuleIndex OBJECT-TYPE The index of this conceptual row. This row represents a single rule for determining if an incoming IP packet indicates the presence of a Convergence End Point device. The lower the numerical value of the index the greater the precedence of the rule. It is recommended that the lowest index be configured to most predominate protocol in the network for greater efficiency. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.1 | Integer32 (1..2147483647) | not-accessible | current |
| etsysConvEndPointDetectionEndPointType OBJECT-TYPE The Convergence End Point device type that a 'hit' on this rule will indicate the presence of. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.2 | INTEGER {h323(0), siemens(1), sip(2)} | read-create | current |
| etsysConvEndPointDetectionProtocol OBJECT-TYPE The IP protocol type that the following port range applies to. If no bits are set then the destination port will not be evaluated as part of the detection process. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.3 | Bits {udp(0), tcp(1)} | read-create | current |
| etsysConvEndPointDetectionPortLow OBJECT-TYPE The low end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the low value in a range of port numbers that will be used to indicate this type of Convergence End Point. This value must be less than or equal to etsysConvEndPointDetectionPortHigh. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.4 | Integer32 (1..65535) | read-create | current |
| etsysConvEndPointDetectionPortHigh OBJECT-TYPE The high end of the range of the IP destination port that will be used for Convergence End Point detection. This value represents the high value in a range of port numbers that will be used to indicate this type of Convergence End Point. This value must be greater than or equal to etsysConvEndPointDetectionPortLow. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.5 | Integer32 (1..65535) | read-create | current |
| etsysConvEndPointDetectionAddrType OBJECT-TYPE The destination address type that will be used for Convergence End Point detection. If the address type is 'unknown', then this value will not be evaluated as part of the detection process. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.6 | InetAddressType | read-create | current |
| etsysConvEndPointDetectionAddr OBJECT-TYPE The destination IP address that will be used for Convergence End Point detection. If this address is null, then this value will not be evaluated as part of the detection process. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.7 | InetAddress | read-create | current |
| etsysConvEndPointDetectionAddrMaskType OBJECT-TYPE The address type of the mask that will be applied to the destination IP address as part of the Convergence End Point detection process. If the address type is 'unknown', then this value will not be evaluated as part of the detection process. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.8 | InetAddressType | read-create | current |
| etsysConvEndPointDetectionAddrMask OBJECT-TYPE The destination address mask that will be used for Convergence End Point detection. If the mask is null, then this value will not be evaluated as part of the detection process. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.9 | InetAddress | read-create | current |
| etsysConvEndPointDetectionRowStatus OBJECT-TYPE The status of this row as defined by the RowStatus textual convention. Rows in this table can only transition to 'notInService', or to 'active' if the etsysConvEndPointDetectionAddrType object and the etsysConvEndPointDetectionAddrMaskType object have the same value, and either their values are not 'unknown' or there is at least one bit set in the etsysConvEndPointDetectionProtocol object. | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.10 | RowStatus | read-create | current |
| etsysCEPDetectionPortConfigTable OBJECT-TYPE A table of per port configuration for Convergence End Point detection. Maintaining the value of this object across system reboots is NOT REQUIRED. | 1.3.6.1.4.1.5624.1.2.40.1.3.3 | not-accessible | current | |
| etsysCEPDetectionPortConfigEntry OBJECT-TYPE An entry containing per port Convergence End Point data. Only interfaces that are able to detect Convergence End Points are represented in this table. | 1.3.6.1.4.1.5624.1.2.40.1.3.3.1 | not-accessible | current | |
| etsysCEPPortClearUsers OBJECT-TYPE Setting this object to a value of true(1) will cause all detected or discovered Convergence End Points to be removed from the following status tables: etsysConvEndPointConnMacTable etsysConvEndPointConnPortTable etsysCEPConnMacTable Setting this object to a value of false(2) has no effect. This object will always return a value of false(2). | 1.3.6.1.4.1.5624.1.2.40.1.3.3.1.1 | TruthValue | read-write | current |
| etsysCEPCdpPortConfigTable OBJECT-TYPE A table of per port configuration for Convergence End Point detection related to the Cisco CDP protocol. Only ports that are capable of participating in Cisco CDP protocol are represented in this table. | 1.3.6.1.4.1.5624.1.2.40.1.3.4 | not-accessible | current | |
| etsysCEPCdpPortConfigEntry OBJECT-TYPE An entry containing per port Convergence End Point data. Only interfaces that are able to detect Convergence End Points are represented in this table. | 1.3.6.1.4.1.5624.1.2.40.1.3.4.1 | not-accessible | current | |
| etsysCEPCiscoCDPVoicePortVlan OBJECT-TYPE This object controls the behavior of the remote configuration of Cisco VOIP phones via Cisco CDP. Setting this object to a value of -1 will cause the device to not attempt to remotely configure a Cisco phone using CDP. Setting this object to a value of 0 will cause the device to configure the phone to send 802.1p priority tagged frames. A value of 4095 will cause the device to configure the phone to send untagged frames. A value in the range 1..4094 will cause the device to configure the phone to send 802.1Q tagged frames using that value as the VLAN ID encoded in the tag. This object SHOULD be maintained across device reboots. | 1.3.6.1.4.1.5624.1.2.40.1.3.4.1.1 | Integer32 (-1 | 0 | 1..4094 | 4095) | read-write | current |
| etsysConvEndPointConformance OBJECT-IDENTITY | 1.3.6.1.4.1.5624.1.2.40.2 | |||
| etsysConvEndPointGroups OBJECT-IDENTITY | 1.3.6.1.4.1.5624.1.2.40.2.1 | |||
| etsysConvEndPointCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.5624.1.2.40.2.2 |
Conformance
| Name | OID | Status |
|---|---|---|
| etsysConvEndPointGlobalConfigGroup OBJECT-GROUP Objects which provide global control of the Convergence End Point features. | 1.3.6.1.4.1.5624.1.2.40.2.1.1 | current |
| etsysConvEndPointConfigGroup OBJECT-GROUP Objects which provide overrides to the global Convergence End Point controls. | 1.3.6.1.4.1.5624.1.2.40.2.1.2 | current |
| etsysConvEndPointDetectionGroup OBJECT-GROUP Objects that provide configuration information specific to IP, port, and address based Convergence End Point detection. | 1.3.6.1.4.1.5624.1.2.40.2.1.3 | deprecated |
| etsysConvEndPointStatusGroup OBJECT-GROUP Objects that provide status information for discovered and detected Convergence End Points. | 1.3.6.1.4.1.5624.1.2.40.2.1.4 | deprecated |
| etsysConvEndPointStatusGroup2 OBJECT-GROUP Objects that provide status information for discovered and detected Convergence End Points. | 1.3.6.1.4.1.5624.1.2.40.2.1.5 | current |
| etsysConvEndPointDetectionGroup2 OBJECT-GROUP Objects that provide configuration information specific to IP, port, and address based Convergence End Point detection. | 1.3.6.1.4.1.5624.1.2.40.2.1.6 | current |
| etsysConvEndPointPortConfigGroup OBJECT-GROUP Objects that provide per port control for discovered and detected Convergence End Points. | 1.3.6.1.4.1.5624.1.2.40.2.1.7 | current |
| etsysConvEndPointCiscoVoiceVLANGroup OBJECT-GROUP Objects that provide per port control for configuring Cisco VOIP phones via Cisco CDP. | 1.3.6.1.4.1.5624.1.2.40.2.1.8 | current |
| etsysConvEndPointCompliance MODULE-COMPLIANCE This compliance statement has been deprecated in favor of the etsysConvEndPointCompliance2 group. | 1.3.6.1.4.1.5624.1.2.40.2.2.1 | deprecated |
| etsysConvEndPointCompliance2 MODULE-COMPLIANCE The compliance statement for entities which implement the Enterasys Convergence End Point Management MIB. | 1.3.6.1.4.1.5624.1.2.40.2.2.2 | current |
| etsysConvEndPointPortConfigCompliance MODULE-COMPLIANCE The compliance statement for devices that support per port configuration of Convergence End Point detection and discovery. | 1.3.6.1.4.1.5624.1.2.40.2.2.3 | current |
| etsysConvEndPointCiscoVoiceVLANCompliance MODULE-COMPLIANCE The compliance statement for devices that support detection and configuration of Cisco VOIP phones via Cisco CDP. | 1.3.6.1.4.1.5624.1.2.40.2.2.4 | current |