ECS4100-52T-MIB

TEXTUAL-CONVENTION

The total length of the key is 1024 characters, it is divided into 8 parts and stored in 8 separated mib variables as below: Key1: part 1 of the key (1-128) Key2: part 2 of the key (129-256) Key3: part 3 of the key (257-384) Key4: part 4 of the key (385-512) Key5: part 5 of the key (513-640) Key6: part 6 of the key (641-768) Key7: part 7 of the key (769-896) Key8: part 8 of the key (897-1024) Please note that if the key string is less then 1024 characters, the remaining part of the string will be filled by a zero-length string. For example, if the length of the key is 129, we will get a string of length 128 in Key1, and a string of length 1 in Key2, moreover, Key3 to Key8 will all be zero-length strings.

TEXTUAL-CONVENTION

The path cost mode of a spanning tree algorithm, short(1) indicates that we retrieve/configure the spanning tree path cost as a 16 bit value and long(2) indicates that we retrieve/configure the spanning tree path cost as a 32 bit value.

TEXTUAL-CONVENTION

A simple status value for the object to create and destroy a table entry. This is a simplified variant of RowStatus as it supports only two values. Setting it to valid(1) creates an entry. Setting it to invalid(2) destroys an entry.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The total number of switches present on this system.

OBJECT-TYPE

Table of descriptive and status information about the switch units in this system.

OBJECT-TYPE

Table providing descriptions and status information for switch units.

OBJECT-TYPE

This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.

OBJECT-TYPE

Hardware version of the main board.

OBJECT-TYPE

Microcode version of the main board.

OBJECT-TYPE

Loader version of the main board.

OBJECT-TYPE

Operation code version of the main board.

OBJECT-TYPE

The number of ports on this switch.

OBJECT-TYPE

Indicates the switch using internalPower(1), redundantPower(2) or both(3)

OBJECT-TYPE

Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.

OBJECT-TYPE

Serial number of the switch.

OBJECT-TYPE

Service tag serial-number of the switch.

OBJECT-TYPE

Model number of the switch.

OBJECT-TYPE

The EPLD version of the switch.

OBJECT-TYPE

The Linux Kernel version of the switch.

OBJECT-TYPE

Global operation state of the switch.

OBJECT-IDENTITY

OBJECT-TYPE

The product name of this switch.

OBJECT-TYPE

The product manufacturer of this switch.

OBJECT-TYPE

The product description of this switch.

OBJECT-TYPE

The runtime code version of this switch.

OBJECT-TYPE

The URL of this switch, which we can connect through a web browser.

OBJECT-TYPE

A unique identifier of which switch in the chassis is currently being looked at.

OBJECT-TYPE

The service tag of the chassis this switch resides in.

OBJECT-TYPE

Table about the status of individual powers.

OBJECT-TYPE

Table about the status of individual power.

OBJECT-TYPE

This is defined as swUnitIndex.

OBJECT-TYPE

1 means internal power, 2 means external power.

OBJECT-TYPE

notPresent(1) means not present, green(2) means up, red(3) means down.

OBJECT-TYPE

enable(1) means the Jumbo Frame has enabled, disabled(2) means the Jumbo Frame has disabled.

OBJECT-IDENTITY

OBJECT-TYPE

If this is enabled(1), the MAC address table will age out according to its timer. If this is disabled(2), the MAC address table will not age out.

OBJECT-TYPE

The number of dot1dTpFdbTable entries in the BRIDGE-MIB.

OBJECT-TYPE

The number of dot1dStaticTable entries in the BRIDGE-MIB.

OBJECT-TYPE

The sum of dot1dTpFdbTable and dot1dStaticTable entries.

OBJECT-TYPE

The action duration configure the duration of an action of mac-thrashing.

OBJECT-TYPE

Table about the status of MAC address mac-thrashing by interface id.

OBJECT-TYPE

Entry of MAC address mac-thrashing by interface ID.

OBJECT-TYPE

The interface number of mac-thrashing MAC address. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The mac-thrashing administrative enabled or disabled.

OBJECT-TYPE

Configures actions of mac-thrashing detected.

OBJECT-TYPE

The mac-thrashing detected port status.

OBJECT-TYPE

The table which collects switch temperature information.

OBJECT-TYPE

A conceptual row of the switchThermalTempTable.

OBJECT-TYPE

The unit of the switch for stackable device.

OBJECT-TYPE

The thermal index of the switch.

OBJECT-TYPE

The temperature of the device in degrees Celsius.

OBJECT-TYPE

The table for configuring the thermal action.

OBJECT-TYPE

A conceptual row of the switchThermalActionTable.

OBJECT-TYPE

The unit of the switch for stackable device.

OBJECT-TYPE

The thermal index of the switch.

OBJECT-TYPE

The action index of the switchTheramlActionTable.

OBJECT-TYPE

The rising threshold of the switch temperature.

OBJECT-TYPE

The falling threshold of the switch temperature.

OBJECT-TYPE

The action that will be taken when the temperature exceeds the rising threshold or falls below the falling threshold.

OBJECT-TYPE

Set valid(1) to create an entry, Set Invalid(2) to delete an entry.

OBJECT-TYPE

released(1) means the Reset button has been released, pressed(2) means the Reset button has been pressed.

OBJECT-IDENTITY

OBJECT-TYPE

Table of descriptive and status information describing the configuration of each switch port. This table also contains information about each trunk.

OBJECT-TYPE

An entry in the table, describing the configuration of one switch port or trunk.

OBJECT-TYPE

The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later).

OBJECT-TYPE

Indicates the port type of the configuration of the switch.

OBJECT-TYPE

Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100Mbps and full duplex mode halfDuplex1000(6) - 1000Mbps and half duplex mode fullDuplex1000(7) - 1000Mbps and full duplex mode halfDuplex10g(8) - 10g and half duplex mode fullDuplex10g(9) - 10g and full duplex mode hundredBaseTX port can be set as: halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) hundredBaseFX port can be set as: fullDuplex100(5) thousandBaseSX port can be set as: fullDuplex1000(7) thousandBaseLX port can be set as: fullDuplex1000(7) thousandBaseT port can be set as: halfDuplex10(2) fullDuplex10(3) halfDuplex100(4) fullDuplex100(5) thousandBaseGBIC port can be set as: fullDuplex1000(7) thousandBaseSfp port can be set as: fullDuplex1000(7) hundredBaseFxScSingleMode port can be set as: fullDuplex100(5) hundredBaseFxScMultiMode port can be set as: fullDuplex100(5) thousandBaseCX port can be set as: fullDuplex1000(7) tenG port can be set as: halfDuplex10g(8) fullDuplex10g(9) The actual operating speed and duplex of the port is given by portSpeedDpxStatus.

OBJECT-TYPE

(1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, the port uses IEEE 802.3x flow control mechanism. If the port type is hundredBaseFX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in fullDuplex mode, Flow control mechanism will not function. (2) Flow control mechanism is disabled. (5) Flow control mechanism is enabled with tx pause mechanism only. (6) Flow control mechansim is enabled with rx pause mechansim only. Fast ethernet ports can be set as: enabled(1), disabled(2). Gigabit ethernet ports can be set as: enabled(1), disabled(2), tx(5), rx(6). The actual flow control mechanism is used given by portFlowCtrlStatus.

OBJECT-TYPE

Port or trunk capabilities.

OBJECT-TYPE

Whether auto-negotiation is enabled.

OBJECT-TYPE

The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case the value is error(1).

OBJECT-TYPE

(2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the member ports have been inconsistently configured then this value is error(1).

OBJECT-TYPE

The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trunkIndex, defined by the corresponding trunkPorts.

OBJECT-TYPE

This determines the running mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect. For a combo port, this has its own valid values not equal to none(1), and setting this variable to none(1) is not allowed. sfpForced(4) is set if user want to force this port running in fiber mode.

OBJECT-TYPE

Configures the PHY mode when auto negotiation is disabled and speed-duplex is 1000full for giga copper port.

OBJECT-TYPE

Set this variable to enabled(1) to start to learn MAC addresses. Set this variable to disabled(2) to stop to learn MAC addresses.

OBJECT-TYPE

The current number of learned MAC addresses.

OBJECT-TYPE

The port up time (in hundredths of a second).

OBJECT-TYPE

The reason of port shutdown. The value is 0 if no shutdown action is applied to this port.

OBJECT-IDENTITY

OBJECT-TYPE

To execute cable diagnostics on a port, assign cableDiagCtlAction to the value of ifIndex defined by the ifIndex in the IF-MIB. When read, this object always returns 0.

OBJECT-TYPE

Table for cable diagnostics result.

OBJECT-TYPE

Entry for cable diagnostics result.

OBJECT-TYPE

This is defined as the ifIndex.

OBJECT-TYPE

The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value openShort(5) means the pair has open and short issues. Value crosstalk(6) means the pair is incorrectly connected at one end. Value unknown(7) means pair has an error matching none of the above. Value impedanceMismatch(8) means different quality cables connected together. Value failed(9) means test failed. Value notSupported(10) means cable diagnostics is not supported. Value noCable(11) means there is no connected cable.

OBJECT-TYPE

The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value openShort(5) means the pair has open and short issues. Value crosstalk(6) means the pair is incorrectly connected at one end. Value unknown(7) means pair has an error matching none of the above. Value impedanceMismatch(8) means different quality cables connected together. Value failed(9) means test failed. Value notSupported(10) means cable diagnostics is not supported. Value noCable(11) means there is no connected cable.

OBJECT-TYPE

The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value openShort(5) means the pair has open and short issues. Value crosstalk(6) means the pair is incorrectly connected at one end. Value unknown(7) means pair has an error matching none of the above. Value impedanceMismatch(8) means different quality cables connected together. Value failed(9) means test failed. Value notSupported(10) means cable diagnostics is not supported. Value noCable(11) means there is no connected cable.

OBJECT-TYPE

The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Value short(4) means conductors are short-circuited together on the pair. Value openShort(5) means the pair has open and short issues. Value crosstalk(6) means the pair is incorrectly connected at one end. Value unknown(7) means pair has an error matching none of the above. Value impedanceMismatch(8) means different quality cables connected together. Value failed(9) means test failed. Value notSupported(10) means cable diagnostics is not supported. Value noCable(11) means there is no connected cable.

OBJECT-TYPE

Displays the fault distance of pair A of the cable in meters.

OBJECT-TYPE

Displays the fault distance of pair B of the cable in meters.

OBJECT-TYPE

Displays the fault distance of pair C of the cable in meters.

OBJECT-TYPE

Displays the fault distance of pair D of the cable in meters.

OBJECT-TYPE

Displays the last time of cable diagnostics. For example, 'Jan 1 02:03:04 2002'.

OBJECT-TYPE

Dispalys port utilization during recent 300 seconds.

OBJECT-TYPE

Dispalys port utilization during recent 300 seconds.

OBJECT-TYPE

The port and trunk interface of the portUtilTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The input octet rate (kbits/sec) of the port.

OBJECT-TYPE

The input packet rate (pkts/sec) of the port.

OBJECT-TYPE

The input utilization of the port, in one per hundred.

OBJECT-TYPE

The output octet rate (kbits/sec) of the port.

OBJECT-TYPE

The output packet rate (pkts/sec) of the port.

OBJECT-TYPE

The output utilization of the port, in one per hundred.

OBJECT-IDENTITY

OBJECT-TYPE

A list of history control entries.

OBJECT-TYPE

A list of parameters that set up a periodic sampling of statistics.

OBJECT-TYPE

An index that uniquely identifies an entry in the portHistControl table.

OBJECT-TYPE

A textual name of the entity. It is mandatory that this only contain printable ASCII characters.

OBJECT-TYPE

This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this portHistControlEntry. This source can be any interface on this device.

OBJECT-TYPE

The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this portHistControlEntry. This interval can be set to any number of seconds between 1 and 86400 (1 day).

OBJECT-TYPE

The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this portHistControlEntry.

OBJECT-TYPE

The number of discrete sampling intervals over which data shall be saved in the part of the media-specific table associated with this portHistControlEntry.

OBJECT-TYPE

The status of this portHistControl entry.

OBJECT-TYPE

A list of Ethernet history entries.

OBJECT-TYPE

An historical sample of Ethernet statistics on a particular Ethernet interface. This sample is associated with the portHistControlEntry which set up the parameters for a regular collection of these samples.

OBJECT-TYPE

The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of portHistControlIndex.

OBJECT-TYPE

An index that uniquely identifies the particular sample this entry represents among all samples associated with the same portHistControlEntry. This index starts at 1 and increases by one as each new sample is taken.

OBJECT-TYPE

The value of sysUpTime at the start of the interval over which this sample was measured.

OBJECT-TYPE

The total number of octets received on the interface, including framing characters.

OBJECT-TYPE

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.

OBJECT-TYPE

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.

OBJECT-TYPE

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.

OBJECT-TYPE

The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.

OBJECT-TYPE

For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol.

OBJECT-TYPE

For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing the number of transmission units received via the interface which were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0.

OBJECT-TYPE

The total number of octets transmitted out of the interface, including framing characters.

OBJECT-TYPE

The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.

OBJECT-TYPE

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses.

OBJECT-TYPE

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.

OBJECT-TYPE

The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.

OBJECT-TYPE

For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors.

OBJECT-TYPE

The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.

OBJECT-TYPE

The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.

OBJECT-TYPE

A list of Ethernet history entries.

OBJECT-TYPE

An historical sample of Ethernet statistics on a particular Ethernet interface. This sample is associated with the portHistControlEntry which set up the parameters for a regular collection of these samples.

OBJECT-TYPE

The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of portHistControlIndex.

OBJECT-TYPE

An index that uniquely identifies the particular sample this entry represents among all samples associated with the same portHistControlEntry. This index starts at 1 and increases by one as each new sample is taken.

OBJECT-TYPE

The value of sysUpTime at the start of the interval over which this sample was measured.

OBJECT-TYPE

The total number of octets received on the interface, including framing characters.

OBJECT-TYPE

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.

OBJECT-TYPE

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.

OBJECT-TYPE

The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.

OBJECT-TYPE

The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.

OBJECT-TYPE

For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol.

OBJECT-TYPE

For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing the number of transmission units received via the interface which were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0.

OBJECT-TYPE

The total number of octets transmitted out of the interface, including framing characters.

OBJECT-TYPE

The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.

OBJECT-TYPE

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses.

OBJECT-TYPE

The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.

OBJECT-TYPE

The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.

OBJECT-TYPE

For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors.

OBJECT-TYPE

The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.

OBJECT-TYPE

The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.

OBJECT-TYPE

This table lists the information of the media device (SFP/XFP/Copper) installed in the physical port. Only the ifIndices of Ethernet ports those are associated with the operational cards will be included in this table.

OBJECT-TYPE

An entry in the Interface Media Information table. The ifIndices of ethernet interfaces will be used to index this table.

OBJECT-TYPE

ifindex.

OBJECT-TYPE

The connector type.

OBJECT-TYPE

The fiber type.

OBJECT-TYPE

The ethernet compliance codes.

OBJECT-TYPE

The baud rate.

OBJECT-TYPE

The OUI of the vendor.

OBJECT-TYPE

The media vendor name, full name of the corporation.

OBJECT-TYPE

The media vendor part number.

OBJECT-TYPE

The media vendor product version number.

OBJECT-TYPE

The vendor serial number of the media device.

OBJECT-TYPE

The date code of the media device.

OBJECT-TYPE

This table lists the instrumented parameters of all optical interfaces.

OBJECT-TYPE

Only the ifIndices of optical interfaces whose parameters need to be monitored will be used to index this table.

OBJECT-TYPE

ifindex.

OBJECT-TYPE

This object holds the value of the transmitter laser diode temperature for the interface. This object indicates the health of the transmitter. The format is xxx.yyyy C(elcius). If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.

OBJECT-TYPE

This object holds the value of the Vcc. It is measured in V. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.

OBJECT-TYPE

Tx Bias Current. It is measured in mA. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.

OBJECT-TYPE

This object holds the value of the transmitter optical signal power for the interface, measured in dBm. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.

OBJECT-TYPE

This object holds the value of the receiver optical signal power for the interface, measured in dBm. If the device support ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.

OBJECT-TYPE

This table lists the threshold of transceivers.

OBJECT-TYPE

Identify the index of the transceiver

OBJECT-TYPE

ifindex.

OBJECT-TYPE

This object holds the low alarm threshold of the transmitter laser diode temperature for the interface.

OBJECT-TYPE

This object holds the low warning threshold of the transmitter laser diode temperature for the interface.

OBJECT-TYPE

This object holds the high warning threshold of the transmitter laser diode temperature for the interface.

OBJECT-TYPE

This object holds the high alarm threshold of the transmitter laser diode temperature for the interface.

OBJECT-TYPE

This object holds the low alarm threshold of the Vcc.

OBJECT-TYPE

This object holds the low warning threshold of the Vcc.

OBJECT-TYPE

This object holds the high warning threshold of the Vcc.

OBJECT-TYPE

This object holds the high alarm threshold of the Vcc.

OBJECT-TYPE

low alarm threshold of Tx Bias Current.

OBJECT-TYPE

low warning threshold of Tx Bias Current.

OBJECT-TYPE

high warning threshold of Tx Bias Current.

OBJECT-TYPE

high alarm threshold of Tx Bias Current.

OBJECT-TYPE

This object holds the low alarm threshold of the transmitter optical signal power for theinterface.

OBJECT-TYPE

This object holds the low warning threshold of the transmitter optical signal power for the interface.

OBJECT-TYPE

This object holds the high warning threshold of the transmitter optical signal power for the interface.

OBJECT-TYPE

This object holds the high alarm threshold of the transmitter optical signal power for the interface.

OBJECT-TYPE

This object holds the low alarm threshold of the receiver optical signal power for the interface.

OBJECT-TYPE

This object holds the low warning threshold of the receiver optical signal power for the interface.

OBJECT-TYPE

This object holds the high warning threshold of the receiver optical signal power for the interface.

OBJECT-TYPE

This object holds the high alarm threshold of the receiver optical signal power for the interface.

OBJECT-TYPE

Indicate the transceiver threshold is retrieved from EEPROM or configured by user.

OBJECT-TYPE

Table for power saving configuration.

OBJECT-TYPE

An entry describing the configuration and status for power saving.

OBJECT-TYPE

The port interface of the powerSavingTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Power saving enabled status.

OBJECT-IDENTITY

OBJECT-TYPE

The maximum number for a trunk identifier.

OBJECT-TYPE

The number of valid trunks.

OBJECT-TYPE

Table describing the configuration and status of each trunk.

OBJECT-TYPE

An entry describing the configuration and status of a particular trunk.

OBJECT-TYPE

Identifies the trunk within the switch that is described by the table entry.

OBJECT-TYPE

The complete set of ports currently associated with this trunk.

OBJECT-TYPE

A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.

OBJECT-TYPE

Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured.

OBJECT-TYPE

This defines the load balancing mode of trunks in the system. It may be based on source and/or destination MAC address or IP address. macSrc(1) means source MAC address. macDst(2) means destination MAC address. macSrcDst(3) means source and destination MAC address. ipSrc(4) means source IP address. ipDst(5) means destination IP address. ipSrcDst(6) means source and destination IP address.

OBJECT-IDENTITY

OBJECT-TYPE

Table for LACP port configuration.

OBJECT-TYPE

Entry for LACP port configuration. While an entry may exist for a particular port, the port may not support LACP and an attempt to enable LACP may result in failure.

OBJECT-TYPE

The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Whether 802.3ad LACP is enabled.

OBJECT-IDENTITY

OBJECT-TYPE

Global spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.

OBJECT-TYPE

The table manages port settings for Spanning Tree Protocol 802.1d, 802.1w or 802.1s depending on the value specified by staProtocolType.

OBJECT-TYPE

The conceptual entry of staPortTable.

OBJECT-TYPE

When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read.

OBJECT-TYPE

The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received.

OBJECT-TYPE

The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.

OBJECT-TYPE

The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the staPortAdminPointToPoint object.

OBJECT-TYPE

Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.

OBJECT-TYPE

The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the 32-bit value range when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this mib object is not instantiated. Setting this to 0 means that the path cost is automatically determined. In this case, read staPortLongOperPathCost to get the oper value.

OBJECT-TYPE

The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the 32-bit value range when the staPathCostMethod is long(2). If the staPathCostMethod is short(1), this mib object is not instantiated.

OBJECT-TYPE

This parameter is used to configure the capability of BPDUs flooding.

OBJECT-TYPE

A value of enabled(1) indicates that BPDU port guard feature is enabled for each port. A value of disabled(2) indicates that the feature is disabled.

OBJECT-TYPE

The administrative value of the edge port parameter. A value of enable(1) indicates that this port should be assumed as an edge-port, a value of disable(2) indicates that this port should be assumed as a non-edge-port and a value of auot (3) indicates this port in RSPT or MSTP mode should be assumed as an edge-port after migration or max age expire without receiving any BPDU and sending BPDU with proposal flag on.

OBJECT-TYPE

The administrative value of the BPDU filter parameter. A value of enabled(1) indicates that this port will avoid transmitting BPDUs on edge-port and the value of disabled(2) indicates that this port will not avoid transmitting BPDUs on edge-port.

OBJECT-TYPE

Specifies the desired status of the root guard. This variable configures the root guard feature to enforce the root bridge placement in the network.

OBJECT-TYPE

A value of enabled(1) indicates that BPDU port guard auto recovery mechanism is enabled for this port. A value of disabled(2) indicates that the mechanism is disabled.

OBJECT-TYPE

The interval in seconds used by BPDU guard auto recovery mechanism.

OBJECT-TYPE

Stop topology change progate on this ifindex. Don't enable on potentially ring port.

OBJECT-TYPE

When enabled, received topology change notifications or topology changes are not propagated to other ports.

OBJECT-TYPE

The version of Spanning Tree Protocol the bridge is currently running. The value 'stp(1)' indicates the Spanning Tree Protocol is as specified in IEEE 802.1D,'rstp(2)' indicates that the Rapid Spanning Tree Protocol is as specified in IEEE 802.1w, and the value 'mstp(3)' indicates that the Multiple Spanning Tree Protocol is as specified in IEEE 802.1s. New values may be defined in the future as new or updated versions of the protocol become available.

OBJECT-TYPE

The value used by the Port Transmit state machine to limit the maximum transmission rate.

OBJECT-TYPE

Indicates the type of spanning tree path cost mode configured on the switch. This mode applies to all instances of the spanning tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the staPortLongPathCost MIB object must be used to retrieve/configure the spanning tree port path cost as a 32-bit value. The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of staPortLongPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in BRIDGE-MIB must be used.

OBJECT-IDENTITY

OBJECT-TYPE

The name of the Multiple Spanning Tree region.

OBJECT-TYPE

The Revision number of the Multiple Spanning Tree region.

OBJECT-TYPE

The max hop number counts of the Multiple Spanning Tree region.

OBJECT-TYPE

This table is used to configure the property of a specific instance in Multiple Spanning Tree or Rapid Spanning Tree. If Rapid Spanning Tree protocol is in use, the mstInstanceEditIndex is always 0.

OBJECT-TYPE

A conceptual row containing the property of the RST or MST instance.

OBJECT-TYPE

An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.

OBJECT-TYPE

The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.

OBJECT-TYPE

The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST.

OBJECT-TYPE

The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized.

OBJECT-TYPE

The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identifier parameter in all configuration bridge PDUs originated by this node.

OBJECT-TYPE

The cost of the path to the root as seen from this bridge of the RST or MST.

OBJECT-TYPE

The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST.

OBJECT-TYPE

The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.

OBJECT-TYPE

The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using in RST or MST.

OBJECT-TYPE

This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.

OBJECT-TYPE

For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the port stays in each of the listening and learning states, which precede the forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the forwarding database. This value is the current value being used by the bridge. xstInstanceCfgBridgeForwardDelay defines the value that this bridge and all others would start using if/when this bridge were to become the root.

OBJECT-TYPE

For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second.

OBJECT-TYPE

For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.

OBJECT-TYPE

For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of xstInstanceCfgBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second.

OBJECT-TYPE

For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate.

OBJECT-TYPE

For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value of this MIB object is changed, the path cost of all ports will be reassigned to the default path cost values based on the new spanning tree path cost mode and the ports' speed. When the value of this MIB object is set to long(2), the xstInstancePortPathCost MIB object must be used in order to retrieve/configure the spanning tree port path cost as a 32-bit value. The set operation on dot1dStpPortPathCost in BRIDGE-MIB will be rejected. While retrieving the value of dot1dStpPortPathCost, the maximum value of 65535 will be returned if the value of xstInstancePortPathCost for the same instance exceeds 65535. When the value of this MIB object is set to short(1), the dot1dStpPortPathCost in BRIDGE-MIB must be used.

OBJECT-TYPE

The extension table for dot1dStpPortEntry to provide additional Spanning Tree information and configuration.

OBJECT-TYPE

The conceptual row for xstInstancePortTable.

OBJECT-TYPE

Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active link in the Spanning Tree. This makes a port with higher priority less likely to be blocked if the Spanning Tree Algorithm is detecting network loops. Where more than one port is assigned the highest priority, the port with lowest numeric identifier will be enabled.

OBJECT-TYPE

The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, but does not forward packets. learning(2): Port has transmitted configuration messages for an interval set by the Forward Delay parameter without receiving contradictory information. Port address table is cleared, and the port begins learning addresses. forwarding(3): Port forwards packets, and continues learning addresses. For ports which are disabled (see xstInstancePortEnable), this object will have a value of discarding(1).

OBJECT-TYPE

The enabled/disabled status of the port.

OBJECT-TYPE

The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached.

OBJECT-TYPE

The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs.

OBJECT-TYPE

The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment.

OBJECT-TYPE

The port identifier of the port on the designated bridge for this port's segment.

OBJECT-TYPE

The number of times this port has transitioned from the learning state to the forwarding state.

OBJECT-TYPE

The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port is connecting a LAN through the bridge to the root bridge (i.e., designated port) (4) The port may provide connectivity if other bridges, bridge ports, or LANs fail or are removed. (5) The port provides backup if other bridges, bridge ports, or LANs fail or are removed. (6) For MST protocol only, indicates whether this instance is in a master role.

OBJECT-TYPE

The admin value of the MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).

OBJECT-TYPE

The oper value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher values assigned to ports with slower media. (Path cost takes precedence over port priority).

OBJECT-TYPE

The Multiple Spanning Tree region instance vlan configuration table. Please read the actual instance vlan mapped in the mstInstanceOperTable.

OBJECT-TYPE

A conceptual row containing the status of the MSTP instance.

OBJECT-TYPE

An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.

OBJECT-TYPE

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'. To create a row, write any of mstInstanceEditVlansMap, mstInstanceEditVlansMap2k, mstInstanceEditVlansMap3k or mstInstanceEditVlansMap4k, to a non-empty list. To destroy a row, write all of these four variables to an empty list.

OBJECT-TYPE

The remaining hop count for this MST instance.

OBJECT-TYPE

The Multiple Spanning Tree region instance vlan mapped table.

OBJECT-TYPE

A conceptual row containing the status of the MSTP instance.

OBJECT-TYPE

An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.

OBJECT-TYPE

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value vlanIndex in that octet. For each VLAN, if it is mapped to this MSTP instance, then the bit corresponding to that VLAN is set to '1'.

OBJECT-TYPE

A table provides the mechanism to configure the spanning tree loopback detection of each port or trunk

OBJECT-TYPE

A conceptual row of staLoopbackDetectionPortTable.

OBJECT-TYPE

The port and the trunk interfaces of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Status of the port on whether spanning tree loopback detection is enabled.

OBJECT-TYPE

The parameter indicates whether the trap has to be sent when the loopback BPDUs have been detected.

OBJECT-TYPE

Setting it to auto(1) indicates that this port can be released from discarding state automatically after loopback has occurred. Setting it to manual(2) indicates that this port can be released from discarding state manually after loopback has occurred.

OBJECT-TYPE

Set this to release(2) to release the port from discarding state. noRelease(1) will always be obtained when reading this variable.

OBJECT-TYPE

Set the interval used when loopback detection action is shutdown.

OBJECT-TYPE

Global BPDU flooding behavior configuration. When BPDU is received on spanning tree disabled port. (1) BPDU is flooded to all other spanning tree disabled ports in vlan that received BPDU. (2) BPDU is flooded to all other spanning tree disabled ports.

OBJECT-TYPE

The feature makes spanning tree operation compatible with Cisco pre-standard versions.

OBJECT-IDENTITY

OBJECT-TYPE

Name of op-code file for start-up.

OBJECT-TYPE

Name of configuration file for start-up.

OBJECT-TYPE

Setting this object to warmBoot(2) causes the device to reinitialize itself such that neither the agent configuration nor the protocol entity implementation is altered. Setting this object to coldBoot(3) causes the device to reinitialize itself such that the agent's configuration or the protocol entity implementation may be altered. When the device is running normally, this variable has a value of running(1).

OBJECT-IDENTITY

OBJECT-TYPE

Table for port mirroring, enabling a port to be mirrored to/from another port. Not all ports can be mirrored and limitations may apply as to which ports can be used as either source or destination ports.

OBJECT-TYPE

The conceptual row of mirrorTable.

OBJECT-TYPE

The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets will be mirrored.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-TYPE

A table that contains the settings of RSPAN.

OBJECT-TYPE

The conceptual row of rspanTable.

OBJECT-TYPE

The session ID that may specify an entry in the table which contains destination port(s) information.

OBJECT-TYPE

Specifies the source port list in tx mode.

OBJECT-TYPE

Specifies the source port list in rx mode.

OBJECT-TYPE

The port number of a destination port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Specifies the traffic which is sent out from source port with RSPAN VLAN ID or not.

OBJECT-TYPE

Specifies the role of current switch.

OBJECT-TYPE

Specifies the uplink port list.

OBJECT-TYPE

Specifies the ID of a RSPAN VLAN.

OBJECT-TYPE

The operational status of the entry. A status of up(1) means the setting of a session is complete and it has started performing its function. A status of down(2) means no function is performed because of incompleted session setting.

OBJECT-TYPE

Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.

OBJECT-IDENTITY

OBJECT-TYPE

Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for IGMP ports.

OBJECT-TYPE

Enables (disables) whether the switch acts as an IGMP querier.

OBJECT-TYPE

Sets the time (in seconds) the switch waits after the previous querier has stopped querying before the router port (which received query packets from previous querier) expires.

OBJECT-TYPE

IGMP version snooped

OBJECT-TYPE

Table for current router ports.

OBJECT-TYPE

Entry for current router ports.

OBJECT-TYPE

The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRouterStaticTable.

OBJECT-TYPE

The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable.

OBJECT-TYPE

The set of ports which are static router ports.

OBJECT-TYPE

Table for static router ports.

OBJECT-TYPE

Entry for static router ports.

OBJECT-TYPE

The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRouterStaticTable.

OBJECT-TYPE

The set of ports which are static router ports.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-TYPE

Table for static multicast addresses.

OBJECT-TYPE

Entry for static multicast addresses.

OBJECT-TYPE

The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable.

OBJECT-TYPE

IP address of multicast group.

OBJECT-TYPE

The set of ports which are members.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-TYPE

Table for enabling or disabling IGMP snooping per VLAN.

OBJECT-TYPE

Entry for enabling or disabling IGMP snooping.

OBJECT-TYPE

Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.

OBJECT-TYPE

Parameter to enable or disable IGMP snooping on this VLAN. When enabled, the device will examine IGMP packets and set up filters for IGMP ports.

OBJECT-TYPE

The parameter to enable or disable the Immediate-Leave feature on this VLAN.

OBJECT-TYPE

The parameter to enable or disable the general query suppresion on this VLAN.

OBJECT-TYPE

Represents the number of queries sent by the switch before it assumes there are no local members.

OBJECT-TYPE

The last member query interval is the max response time inserted into group-specific queries sent in response to leave group messages,and is also the the max response time inserted into group-and-source-specific query messages.

OBJECT-TYPE

Represents the address of queries sent by the switch.

OBJECT-TYPE

Represents the query interval of queries sent by the switch.

OBJECT-TYPE

Represents the query response interval of queries sent by the switch.

OBJECT-TYPE

Set this variable to enabled(1) to enable the feature. Set this variable to disabled(2) to disable the feature. Set this variable to default(3), the status of the feature is decided by the global configuration.

OBJECT-TYPE

the version of igmp packets is supported by this vlan.

OBJECT-TYPE

Enable/disable control of the IGMP Snooping exclusive supported version.

OBJECT-TYPE

The parameter to enable or disable the Immediate-Leave feature by host ip on this VLAN.

OBJECT-TYPE

Table for current multicast addresses.

OBJECT-TYPE

Entry for Group multicast addresses.

OBJECT-TYPE

The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMulticastStaticTable.

OBJECT-TYPE

IP address of multicast group.

OBJECT-TYPE

Source IP address of source.

OBJECT-TYPE

The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable.

OBJECT-TYPE

The set of ports which are static IGMP member ports.

OBJECT-TYPE

The number of forwarding port in this group

OBJECT-TYPE

Parameter to enable or disable IGMP filtering on the device.

OBJECT-TYPE

The table for configuring the IGMP snooping profile.

OBJECT-TYPE

The entry for configuring the IGMP snooping profile.

OBJECT-TYPE

The ID of the IGMP snooping profile.

OBJECT-TYPE

The access mode of the IGMP snooping profile.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-IDENTITY

OBJECT-TYPE

The ID of the IGMP snooping profile. The default value is zero, meaning that no ID is specified. In order to create a profile, a non-zero value must be specified.

OBJECT-TYPE

The address type is associated with this agent. Only ipv4(1) type is supported.

OBJECT-TYPE

The specified addresses in the start of the controlled IP multicast addresses.

OBJECT-TYPE

The specified addresses in the end of the controlled IP multicast addresses.

OBJECT-TYPE

Setting it to create(2) creates the range of the controlled IP multicast addresses. Setting it to destroy(3) destroys the range of the controlled IP multicast addresses. When the action is completed, this object becomes noAction(1).

OBJECT-TYPE

The table for configuring the range of the IGMP snooping profile.

OBJECT-TYPE

The entry for configuring the range of the IGMP snooping profile.

OBJECT-TYPE

This is defined as igmpSnoopProfileId.

OBJECT-TYPE

The address type is associated with this agent. Only ipv4(1) type is supported.

OBJECT-TYPE

The specified addresses in the start of the controlled IP multicast addresses.

OBJECT-TYPE

The specified addresses in the end of the controlled IP multicast addresses.

OBJECT-TYPE

The access mode of the IGMP snooping profile.

OBJECT-TYPE

Table for port configuration in IGMP filtering.

OBJECT-TYPE

Entry for port configuration in IGMP filtering.

OBJECT-TYPE

The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. If there is no corresponding entry in the igmpSnoopProfileTable, then no association exists. In particular, if this value is zero, no associated profile will be generated, as zero is not a valid profile index.

OBJECT-TYPE

Table for port configuration in IGMP throttling.

OBJECT-TYPE

Entry for port configuration in IGMP throttling.

OBJECT-TYPE

The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Describes the running status of the IGMP throttling to the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) indicates the IGMP throttling mechanism is inactive.

OBJECT-TYPE

The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and the number of current joined multicast groups is equal to the maximum number of IGMP groups that the interface can join. A value of deny(2) means to deny the IGMP report request when an interface receives an IGMP report and the number of current joined multicast groups is equal to the maximum number of IGMP groups that the interface can join.

OBJECT-TYPE

The maximum number of IGMP groups that the interface can join.

OBJECT-TYPE

The current number of IGMP groups that the interface has joined.

OBJECT-TYPE

Table of IGMP Snooping service per port.

OBJECT-TYPE

Entry of IGMP Snooping service per port.

OBJECT-TYPE

The port and the trunk (excluding trunk members) interface of the igmpSnoopPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Parameter to enable or disable dropping IGMP Query packet.

OBJECT-TYPE

Parameter to enable or disable dropping IP multicast data

OBJECT-TYPE

Current learned groups

OBJECT-TYPE

Number of join send

OBJECT-TYPE

Number of join recieved

OBJECT-TYPE

Number of join group success

OBJECT-TYPE

Number of leave send

OBJECT-TYPE

Number of leave received

OBJECT-TYPE

Number of general query send.

OBJECT-TYPE

Number of general query received.

OBJECT-TYPE

Number of specific query send.

OBJECT-TYPE

Number of specific query received.

OBJECT-TYPE

Number of invalid report received.

OBJECT-TYPE

Clear this VLAN all statistics

OBJECT-TYPE

Parameter to enable or disable IGMP Authentication

OBJECT-IDENTITY

OBJECT-TYPE

Parameter to enable or disable IGMP snooping proxy reporting on the device.

OBJECT-TYPE

Parameter to enable or disable IGMP snooping router alert option check on the device.

OBJECT-TYPE

Parameter to enable or disable IGMP snooping tcn flood on the device.

OBJECT-TYPE

Parameter to enable or disable IGMP snooping tcn query solicit on the device.

OBJECT-TYPE

Parameter to enable or disable IGMP snooping Unregistered data flood solicit on the device.

OBJECT-TYPE

Setting this value to specify how long (in seconds) the uplink ports should transmit unsolicited reports.

OBJECT-TYPE

Parameter to enable or disable IGMP snooping version exclusive on the device.

OBJECT-TYPE

Paremete to set IGMP snooping Mrouter port forward mode. When set dynamic, IGMP snooping Mrouter port won't forward multicast streams received from other mrouter port. When set forward, IGMP snooping Mrouter port will forward multicast streams received from other mrouter port.

OBJECT-TYPE

Table of IGMP Snooping query drop per vlan and per vlan configuration.

OBJECT-TYPE

Entry of IGMP Snooping service per port and per VLAN.

OBJECT-TYPE

The port and the trunk (excluding trunk members) interface of the igmpSnoopPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The VLAN bitmap which query drop applied on this port. If all zero, it means disable, For all VLAN, please use igmpSnoopPortTable to configure.

OBJECT-TYPE

Clear all IGMP groups which are learned by IGMP report and MVR.

OBJECT-TYPE

Table of IGMP Snooping service per port.

OBJECT-TYPE

Entry of IGMP Snooping service per VLAN.

OBJECT-TYPE

VLAN ID

OBJECT-TYPE

Current learned groups

OBJECT-TYPE

Number of join send.

OBJECT-TYPE

Number of join received

OBJECT-TYPE

Number of jion success

OBJECT-TYPE

Number of leave send.

OBJECT-TYPE

Number of leave received

OBJECT-TYPE

Number of general query send

OBJECT-TYPE

Number of general query received

OBJECT-TYPE

Number of specific query send

OBJECT-TYPE

Number of sepcific query received

OBJECT-TYPE

Number of invalid report received

OBJECT-TYPE

Clear this VLAN statistics

OBJECT-IDENTITY

OBJECT-TYPE

A table of netConfigEntry.

OBJECT-TYPE

A set of configuration parameters for a particular network interface on this device. If the device has no network interface, this table is empty. The index is composed of the ifIndex assigned to the corresponding interface.

OBJECT-TYPE

The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table.

OBJECT-TYPE

The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask is 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).

OBJECT-TYPE

The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what these values should be. If BOOTP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).

OBJECT-TYPE

Whether this is a primary interface.

OBJECT-TYPE

Whether this is an unnumbered interface.

OBJECT-TYPE

The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.

OBJECT-TYPE

Whether HTTP is enabled.

OBJECT-TYPE

The port number for HTTP.

OBJECT-TYPE

When set to restart(1) the DHCP server will restart. When read, this value always returns noRestart(2).

OBJECT-TYPE

Whether HTTPS is enabled.

OBJECT-TYPE

The port number for HTTPS.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Table for DHCP client information listed by interface. Depending on the nature of the product, this table may have only one entry(e.g. for the management VLAN), or may have many entries(e.g. for all ports, or for all static VLANs).

OBJECT-TYPE

Entry for DHCP client information listed by interface.

OBJECT-TYPE

This is defined by ifIndex in the IF-MIB.(static vlan if index)

OBJECT-TYPE

Whether the vendor class ID is in text mode or in Hex mode.

OBJECT-TYPE

The value that the DHCP client sets in the vendor class_id option of DHCPDISCOVER and DHCPREQUEST messages. This value may be used by DHCP servers to identify vendor classof the client.

OBJECT-IDENTITY

OBJECT-TYPE

Set this object to restart(1) to restart DCHP Relay. Always get noRestart(2) when you read this variable.

OBJECT-TYPE

The role of DHCP Relay Agent is to forward requests and replies between server and client when they are not in the same subnet. To enable DHCP Relay service user needs to specify Relay Server IP address and then restart DHCP Relay. This Table is to specify Relay Server IP address,the maximum numbers of server IP address user can specify is 5.To Restart DHCP Relay, please use the dhcpRelayRestart variable.

OBJECT-TYPE

A conceptual row of dhcpRelayServerAddrTable.

OBJECT-TYPE

The VLAN interface being used by this table entry.

OBJECT-TYPE

The Index of the Relay server IP address.

OBJECT-TYPE

The INET address type of the relay server.

OBJECT-TYPE

The INET address of the relay server.

OBJECT-IDENTITY

OBJECT-TYPE

Setting this to 1 to enable the DHCP server service. Setting this to 2 to disable the DHCP server service.

OBJECT-TYPE

A DHCP pool is a collection of user configuration such as option config-lease time or DNS-server IPs, a network address for network pool, or a host IP plus a hardware address pair for host pool. However, a DHCP pool only can either be a network pool or a host pool, or none of them (such as that pool only containing option config no network address config or a host IP config as well).

OBJECT-TYPE

A conceptual row of dhcpPoolInetTable.

OBJECT-TYPE

Pool name, simply specify a string with its length NO MORE THAN 32.

OBJECT-TYPE

Pool type: notSpecified(1), network(2), host(3).

OBJECT-TYPE

Pool address type

OBJECT-TYPE

Pool address

OBJECT-TYPE

subnet mask type

OBJECT-TYPE

subnet mask

OBJECT-TYPE

Hardware type: notSpecified(1), ethernet(2), ieee802(3) ,fddi(4).

OBJECT-TYPE

MAC address.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-TYPE

This is the Option table of the dhcpPoolTable, user can specify options configuration in this table.

OBJECT-TYPE

A conceptual row of dhcpPoolOptionTable.

OBJECT-TYPE

Pool name, simply specify a string with its length NO MORE THAN 32.

OBJECT-TYPE

Specifies the INET address type of the next server in the boot process.

OBJECT-TYPE

Specifies the INET address of the next server in the boot process, which is typically a Trivial File Transfer Protocol(TFTP) server. One INET address is required.

OBJECT-TYPE

Specifies the NetBIOS node type. Valid types are: none(1) b-node(2) - Broadcast p-node(3) - Peer-to-peer m-node(4) - Mixed h-node(5) - Hybrid.

OBJECT-TYPE

Specifies the domain name string.

OBJECT-TYPE

To specify the name of the default boot image.

OBJECT-TYPE

To configure the duration of the lease, in seconds, of an IP address that is assigned from a DHCP Server to a DHCP client. Valid values are from 1 to 31536000 (365 days), and a large number '7FFFFFFF'h, which is 'practically infinite'.

OBJECT-TYPE

Set this variable to text(2) or hex(3) to specify the mode of the client ID, which is useful for CLI to determine the display format of the client ID. The original value of object is set to 'notSpecified(1)'. But setting it to notSpecified(1) is a invalid operation.

OBJECT-TYPE

Content of Client Id. dhcpPoolOptionCidMode MUST be specified before setting this variable.

OBJECT-TYPE

To specify the DNS IP servers available to a DHCP client, you can specify up to two addresses for each DHCP pool.

OBJECT-TYPE

A conceptual row of dhcpPoolOptionDnsSerTable.

OBJECT-TYPE

Pool name, simply specify a string with its length NO MORE THAN 32.

OBJECT-TYPE

Index of the DNS server.

OBJECT-TYPE

INET address type of the DNS server.

OBJECT-TYPE

INET address of the DNS server.

OBJECT-TYPE

Specifies the default router list for a DHCP Client, you can specify up to two addresses for each DHCP pool.

OBJECT-TYPE

A conceptual row of dhcpPoolOptDefaultRouterTable.

OBJECT-TYPE

Pool name, simply specify a string with its length NO MORE THAN 32.

OBJECT-TYPE

Index of the default router.

OBJECT-TYPE

Specifies the INET address type of a router.

OBJECT-TYPE

Specifies the INET address of a router.

OBJECT-TYPE

To configure the NetBIOS WINS name servers that are available to DHCP clients. You can specify up to eight addressed for each DHCP pool.

OBJECT-TYPE

A conceptual row of dhcpPoolOptNetbiosServerTable.

OBJECT-TYPE

Pool name, simply specify a string with its length NO MORE THAN 32

OBJECT-TYPE

Index of the NetBIOS name Server.

OBJECT-TYPE

Specifies the INET address type of the NetBIOS WINS name server.

OBJECT-TYPE

Specifies the INET address of the NetBIOS WINS name server.

OBJECT-TYPE

To specify IP addresses that a DHCP Server should not assign to DHCP clients.

OBJECT-TYPE

A conceptual row of dhcpServerExcludedIpAddrTable.

OBJECT-TYPE

The excluded INET address type, or first INET address type in an excluded address range.

OBJECT-TYPE

The excluded INET address, or first INET address in an excluded address range.

OBJECT-TYPE

The last INET address type in the excluded address range.

OBJECT-TYPE

The last INET address in the excluded address range.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-TYPE

To configure the address bindings on the DHCP server.

OBJECT-TYPE

A conceptual row of dhcpServerLeaseBindingTable.

OBJECT-TYPE

The INET address type of the host as recorded on the DHCP server.

OBJECT-TYPE

The INET address of the host as recorded on the DHCP server.

OBJECT-TYPE

The MAC address of the host as recorded on the DHCP Server.

OBJECT-TYPE

The lease expiration date of the INET address of the host.

OBJECT-TYPE

Show current system real time in sec.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-TYPE

To configure the option 43 Vendor Specific Information for DHCP clients. You can specify option type for each DHCP pool.

OBJECT-TYPE

A conceptual row of dhcpPoolOptInetVendorSpecInfoTable.

OBJECT-TYPE

Pool name, simply specify a string with its length NO MORE THAN 32

OBJECT-TYPE

Index of the Vendor Specific Information.

OBJECT-TYPE

Specify the mode of the Vendor Specific Information, ascii(2) or hex(3) MUST be specified the content in dhcpPoolOptInetVendorSpecInfoBuffer, ip-address(4) MUST be specified the content in dhcpPoolOptInetVendorSpecInfoAddr.

OBJECT-TYPE

Content of option 43 Vendor Specific Information. dhcpPoolOptInetVendorSpecInfoMode MUST be specified before setting this variable.

OBJECT-TYPE

Specifies the INET address of the option 43 Vendor Specific Information. dhcpPoolOptInetVendorSpecInfoMode MUST be specified before setting this variable.

OBJECT-IDENTITY

OBJECT-TYPE

Set enabled(1) to enable DHCP Relay Option 82, set disabled(2) to disable it.

OBJECT-TYPE

Provide three policies to handle packet

OBJECT-TYPE

Provide five mode for insertion remote-id sub-option of option 82. If configured-string(5) has been set, dhcpOption82RemoteIDString will take effect.

OBJECT-TYPE

Set string to remote-id sub-option of option 82. It only take effect when dhcpOption82RemoteIDMode is set to configured-string(5)

OBJECT-TYPE

Set encode format for CID and RID in option82. Set extra-subtype-included(1) will have extra subtype and length field in CID and RID. Set no-extra-subtype-included(2) will only have TLV format for CID and RID.

OBJECT-TYPE

This table is to specify relay server IP address, the maximum number of server IP addresses user can specify is 5.

OBJECT-TYPE

A conceptual row of dhcpOption82RelayServerAddrTable.

OBJECT-TYPE

The index of the relay server IP address.

OBJECT-TYPE

The IP address of the relay server.

OBJECT-TYPE

A table contains DHCP option82 configurations for existing VLANs.

OBJECT-TYPE

An instance contains the configuration to enable or disable DHCP option82 for each existing VLAN.

OBJECT-TYPE

This object indicates the VLAN ID on which DHCP Option82 feature is configured.

OBJECT-TYPE

This object indicates whether DHCP Option82 is enabled in this VLAN.

OBJECT-TYPE

A table contains DHCP option82 configurations for port interfaces.

OBJECT-TYPE

An instance contains the configuration to enable or disable DHCP option82 at each port interface.

OBJECT-TYPE

The ifIndex value of the port.

OBJECT-TYPE

This object indicates whether the port is enabled for DHCP Option82.

OBJECT-TYPE

A per-system enable/disable configuration to decide whether to use the specified configuration file in DHCP packet. It shall use the specified configuration file in DHCP packet if this configuration is disabled and the start-up configuration file is Factory_Default_Config.cfg.

OBJECT-IDENTITY

OBJECT-TYPE

Specifies the IP address of the device that is planned to ping.

OBJECT-TYPE

Specifies the size of each data potion of ping packets in bytes.

OBJECT-TYPE

A value of true(1) will be read when this ping operation has been either responded to or changed to the time-out status. A value of false(2) will be read when there is a ping operation running and all associated objects in the pingMgt operation cannot be modified during this period.

OBJECT-TYPE

The action of the pingMgt operation. Sets these objects to pingStart(2) to begin the ping operation. Once the action is set to pingStart(2), the associated pingMgt objects cannot be modified until this ping operation is completed (pingCompleted is true). When the ping has ended or there is no ping operation performing, this object will get a value of noAction(1).

OBJECT-TYPE

Specifies the number of times to perform a ping operation at a remote host.

OBJECT-TYPE

The value of this object reflects the number of probes sent. The value of this object must be reported as 0 when no probes have been sent.

OBJECT-TYPE

Number of responses received. The value of this object must be reported as 0 when no probe responses have been received.

OBJECT-TYPE

Packet loss rate of this ping operation. This variable is calculated by pingReceivedPackets and pingSentPackets. The rate is expressed as a percentage.

OBJECT-TYPE

Contains the executive result information for the ping operation.

OBJECT-TYPE

A conceptual row in the pingHistory table.

OBJECT-TYPE

A new entry in this table is created when the result of a ping probe is determined. The old entries will be cleared when a new ping action is started.

OBJECT-TYPE

This variable represents the round trip time and is measured in milliseconds. The variable is the difference between received time and sent time for a ping probe. If the difference value is more than the time-out value or no response is received, then the variable will be 5000 milliseconds.

OBJECT-TYPE

To delete current HTTPS certificate in flash, write this variable to delete(1). Writing this variable to noDelete(2) has no effect on the device. When read, this variable always returns noDelete(2).

OBJECT-IDENTITY

OBJECT-TYPE

Table for VLAN configuration.

OBJECT-TYPE

Entry for VLAN configuration.

OBJECT-TYPE

Based on dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.

OBJECT-TYPE

Method to get the IP address.

OBJECT-TYPE

Table for port configuration in VLAN.

OBJECT-TYPE

Entry for port configuration in VLAN.

OBJECT-TYPE

The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qPvid in the Q-BRIDGE-MIB.

OBJECT-TYPE

This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) sets an access link.

OBJECT-IDENTITY

OBJECT-TYPE

A table containing the mac address which can be identified by Voice VLAN.

OBJECT-TYPE

A table containing the mac address which can be identified by Voice VLAN.

OBJECT-TYPE

MAC address can be identified by voice vlan.

OBJECT-TYPE

The mask of MAC address.

OBJECT-TYPE

The description of OUI.

OBJECT-TYPE

Current operation status of the row.

OBJECT-TYPE

Voice VLAN enabled status and VLAN ID: enabled (1..4093), disabled (-1).

OBJECT-TYPE

Voice VLAN aging time, the unit of which is minute.

OBJECT-TYPE

A list of voice VLAN port entries.

OBJECT-TYPE

An entry containing Voice VLAN port information, which is applicable to a Voice VLAN enabled interface.

OBJECT-TYPE

The index of interface on which Voice VLAN function is enabled.

OBJECT-TYPE

Voice VLAN configuration mode status.

OBJECT-TYPE

If the security is enabled, the port only allows voice traffic for the Voice VLAN.

OBJECT-TYPE

The priority of the voice vlan traffic in the port.

OBJECT-TYPE

The address of voice device is learned from OUI table.

OBJECT-TYPE

The address of voice device is learned from LLDP discovery.

OBJECT-TYPE

Remaining aging time, the unit of which is minute.

OBJECT-IDENTITY

OBJECT-TYPE

This parameter is used to globally enable/disable 802.1Q Tunneling on the device.

OBJECT-TYPE

Table for port configuration in 802.1Q Tunneling.

OBJECT-TYPE

Entry for port configuration in 802.1Q Tunneling.

OBJECT-TYPE

The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

This variable sets the 802.1Q Tunneling mode. Setting it to none(1) indicates no mode in this port. Setting it to access(2) sets as dot1q-tunnel mode port which link to customer. Setting it to uplink(3) sets as dot1q-tunnel mode port which link to service-provider. If vlanDot1qTunnelStatus is disabled, it means vlanDot1qTunnelPortMode is inactive.

OBJECT-TYPE

TPID for 802.1Q encapsulation. It's used to select a nonstandard (nondefault) 2-byte ethertype to identify 802.1Q tagged frames.

OBJECT-TYPE

Status of priority mapping. Set to enabled(1) to use 802.1p priority of inner tag as packet's priority instead of using outer tag.

OBJECT-TYPE

A table that contains protocol Vlan priority information.

OBJECT-TYPE

A list of protocol VLAN user priority sets for each port.

OBJECT-TYPE

Specifies the priority in the added tag for qualified frames.

OBJECT-TYPE

A table that contains the settings for MAC-based VLAN.

OBJECT-TYPE

A conceptual row in the macVlanTable.

OBJECT-TYPE

The MAC address that may specify an entry in the table which contains MAC-based VLAN information.

OBJECT-TYPE

Specifies the VLAN ID which the MAC address associates with.

OBJECT-TYPE

Specifies the priority whcich the MAC address associates with.

OBJECT-TYPE

Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.

OBJECT-TYPE

The MAC address mask that may specify an entry in the table which contains MAC-based VLAN information.

OBJECT-TYPE

Action for clearing macVlanTable. When this object is set to clear(2), all entries in macVlanTable will be cleared. When this object is read, the value of this object is always noClear(1).

OBJECT-TYPE

A table that contains the settings for IP subnet-based VLAN.

OBJECT-TYPE

A conceptual row in the subnetVlanTable.

OBJECT-TYPE

The IPv4 address of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanMask object is not equal to x.

OBJECT-TYPE

The netmask of a subnet. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the subnetVlanIpAddress object is not equal to subnetVlanIpAddress.

OBJECT-TYPE

Specifies the VLAN ID which the subnet associates with.

OBJECT-TYPE

Specifies the priority whcich the subnet associates with.

OBJECT-TYPE

Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.

OBJECT-TYPE

Action for clearing subnetVlanTable. When this object is set to clear(2), all entries in subnetVlanTable will be cleared. When this object is read, the value of this object is always noClear(1).

OBJECT-TYPE

The extension table of dot1qVlanStaticTable. This table enhances the original table with extra vlanStaticExtRspanStatus to create and destroy RSPAN VLAN(s).

OBJECT-TYPE

A conceptual row in the vlanStaticExtTable.

OBJECT-TYPE

Displays type of a VLAN is vlan(2) or rspanVlan(3). Set this to destroy(1) to destroy a RSPAN VLAN. Set this to rspanVlan(3) to create a RSPAN VLAN. Setting this to vlan(2) is not allowed.

OBJECT-TYPE

Table for port configuration in Layer 2 Protocol Tunneling.

OBJECT-TYPE

Entry for port configuration in Layer 2 Protocol Tunneling.

OBJECT-TYPE

The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Set enabled(1) to enable Layer 2 protocol tunneling for spanning-tree protocol. Set disabled(2) to disable Layer 2 protocol tunneling for spanning-tree protocol.

OBJECT-TYPE

Set enabled(1) to enable Layer 2 protocol tunneling for LLDP. Set disabled(2) to disable Layer 2 protocol tunneling for LLDP.

OBJECT-TYPE

Set enabled(1) to enable Layer 2 protocol tunneling for Cisco Discovery Protocol. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco Discovery Protocol.

OBJECT-TYPE

Set enabled(1) to enable Layer 2 protocol tunneling for Cisco VTP. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco VTP.

OBJECT-TYPE

Set enabled(1) to enable Layer 2 protocol tunneling for Cisco PVST+. Set disabled(2) to disable Layer 2 protocol tunneling for Cisco PVST+.

OBJECT-TYPE

Set enabled(1) to enable Layer 2 protocol tunneling for LACP. Set disabled(2) to disable Layer 2 protocol tunneling for LACP.

OBJECT-TYPE

Table for static VLAN configuration including VLAN aggregation support.

OBJECT-TYPE

Static information for a VLAN configured on the device by (local or network) management.

OBJECT-TYPE

The VLAN ID of the VLAN.

OBJECT-TYPE

The interface type of the VLAN (there is a subtype of IANAifType). l2vlan(135) refers to L2 interface and can't accept any L3 related configuration. l3ipvlan(136) refers to L3 interface and can accept L3 related configuration.

OBJECT-TYPE

Table for port configuration to specify how to insert outer tag by matching customer VLAN ID.

OBJECT-TYPE

Entry for port configuration to specify how to insert outer tag by matching customer VLAN ID.

OBJECT-TYPE

The port interface of the vlanDot1qTunnelSrvCvidPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Specifies customer VLAN ID.

OBJECT-TYPE

Specifies service VLAN ID.

OBJECT-TYPE

Set to valid(1) to create an entry. Set to invalid(2) to destroy an entry.

OBJECT-TYPE

Sets action of this entry.

OBJECT-IDENTITY

OBJECT-TYPE

Destination MAC address for PDU tunneling.

OBJECT-TYPE

Table for port configuration to specify the behavior of default service.

OBJECT-TYPE

Entry for port configuration to specify the behavior of default service.

OBJECT-TYPE

The port interface of the vlanDot1qTunnelSrvDfltPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Set to valid(1) to create an entry. Set to invalid(2) to destroy an entry.

OBJECT-TYPE

Sets action of this entry.

OBJECT-TYPE

Table for port configuration to specify the behavior of discarding untagged traffic.

OBJECT-TYPE

Entry for port configuration to specify the behavior of discarding untagged traffic.

OBJECT-TYPE

The port interface of the vlanDot1qTunnelUntagDiscardPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Set to valid(1) to create an entry. Set to invalid(2) to destroy an entry.

OBJECT-IDENTITY

OBJECT-TYPE

Table for per port weighted round robin (WRR).

OBJECT-TYPE

Entry for per port weighted round robin (WRR).

OBJECT-TYPE

The port interface of the prioWrrPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Traffic class for this entry, as defined in dot1dTrafficClass in the P-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTrafficClasses-1.

OBJECT-TYPE

Weight for this entry. Value of the object should be ignored when prioQueueMode is strictAndWrr(3), and prioWrrPortStrictStatus is enabled(1).

OBJECT-TYPE

This object is used when prioSchedModePort is strictAndWrr(4).

OBJECT-TYPE

Table for per port scheduling mode.

OBJECT-TYPE

Entry for per port scheduling mode.

OBJECT-TYPE

The port interface of the prioSchedModePortEntry.

OBJECT-TYPE

The scheduling mode status of ethernet port. wrr(1),strict(2), strict-wrr(4)

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This variable is for trap var binding, indicated the ipfilter reject mode. web(1), snmp(2), telnet(3).

OBJECT-TYPE

This variable is for trap var binding, indicating the IP address that rejected by the ipfilter.

OBJECT-TYPE

The MAC address.

OBJECT-TYPE

The name of the user who logs into the switch.

OBJECT-TYPE

The method by which the user logs in to control the switch.

OBJECT-TYPE

The address type of the address associated with this agent. Only IPv4 and IPv6 types are supported.

OBJECT-TYPE

The IP address from which the user logs into the switch.

OBJECT-TYPE

This variable is for trap var binding, indicating the IP address that was rejected by the IP filter.

OBJECT-TYPE

This variable is for trap var binding, indicating the IP address that was rejected by the IP filter.

OBJECT-TYPE

The parameter indicates which result triggers the trap.

OBJECT-TYPE

The parameter indicates new version which was upgraded to. When trapAutoUpgradeResult was failed(2), it would be null string.

OBJECT-TYPE

This variable is for trap var binding, indicating the index of an interface.

OBJECT-TYPE

This variable is for trap var binding, indicating the identifier of a VLAN.

OBJECT-TYPE

ifIndex for the port connected to DHCP rogue server.

OBJECT-TYPE

The IP address of the rogue server.

OBJECT-TYPE

ifIndex for the port issued alarm/warning trap.

OBJECT-TYPE

SFP's alarm/warning type .

OBJECT-TYPE

The MAC address of the rogue server.

OBJECT-TYPE

The parameter indicates which result triggers the trap.

OBJECT-TYPE

The name of the owner for sFlow trap.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Table for rate limit of each port.

OBJECT-TYPE

Entry for rate limit of each port.

OBJECT-TYPE

The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Whether input rate limit is enabled for this port.

OBJECT-TYPE

Whether output rate limit is enabled for this port.

OBJECT-TYPE

Value of the input rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000.

OBJECT-TYPE

Value of the output rate limit. Its unit is kilobits per second. For a 100 Mbps port, the range is 64 to 100000. For a 1000 Mbps port, the range is 64 to 1000000.

OBJECT-TYPE

Present the rate's resolution. Its unit is kilobits per second

OBJECT-IDENTITY

OBJECT-TYPE

Table for setting the interface Qos mapping classification mode.

OBJECT-TYPE

Entry for setting the interface Qos mapping classification mode.

OBJECT-TYPE

The port or trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The Qos mapping classification mode of the interface. cos mode means that the internal priority is mapped from priority field of packet's VLAN tag if a VLAN tag exists; IP precedence mode means that the internal priority is mapped from the IP precedence value of IP packets; DSCP mode means the internal priority is mapped from the dscp value of IP packets.

OBJECT-TYPE

Table for cos to queue mapping.

OBJECT-TYPE

Entry for cos to queue mapping.

OBJECT-TYPE

The port or trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The cos value on VLAN tag of inject packet.

OBJECT-TYPE

The cfi value on VLAN tag of inject packet.

OBJECT-TYPE

The queue value which is mapped from the (cos,cfi) value of QoS label.

OBJECT-TYPE

Table for dscp to queue mapping.

OBJECT-TYPE

Entry for dscp to queue mapping.

OBJECT-TYPE

The port or trunk interface of the device. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

The dscp value on VLAN tag of inject packet.

OBJECT-TYPE

The queue value which is mapped from the dscp value of QoS label.

OBJECT-IDENTITY

OBJECT-TYPE

Table for policy map.

OBJECT-TYPE

Entry for policy map.

OBJECT-TYPE

An index that uniquely identifies an entry in this table.

OBJECT-TYPE

The name of this entry.

OBJECT-TYPE

The description of this entry.

OBJECT-TYPE

The octet string containes the diffServPolicyMapElementEntry indexes. Two octets express one index and it is represented in network order. This index list indicates the diffServPolicyMapEntrys which belong to this entry.

OBJECT-TYPE

This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active');it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-IDENTITY

OBJECT-TYPE

Index for attachment control. Specifies the policy map as the target to relate with the policy map element. The policy map identified by a particular value of this index is associated with the same diffServPolicyMapEntry as identified by the same value of diffServPolicyMapIndex.

OBJECT-TYPE

Element Index for attachment control.Specifies the policy map element to relate with the policy map. The policy map element identified by a particular value of this index is associated with the same diffServPolicyMapElementEntry as identified by the same value of diffServPolicyMapElementIndex.

OBJECT-TYPE

Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular policy map element is attached to a particular policy map. When setting this object to detach(3) to begin the not attached operation, a particular policy map element is not attached to a particular policy map. When the action is finshed or no action is taken, the value of this object is noAction(1). A particular policy map is specified in the diffServPolicyMapAttachCtlIndex. A particularpolicy map element is specified in the diffServPolicyMapAttachCtlElementIndex.

OBJECT-TYPE

Table for policy map element.

OBJECT-TYPE

Entry for policy map element.

OBJECT-TYPE

An index that uniquely identifies an entry in this table.

OBJECT-TYPE

Specifies the class map binding to this entry. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex.

OBJECT-TYPE

Specifies the meter binding to this entry. The meter identified by a particular value of this index is associated with the same diffServMeterEntry as identified by the same value of diffServMeterIndex. If this value is zero, no associated meter will be associated, as zero is not a valid meter index.

OBJECT-TYPE

Specifies the action binding to this entry. The action identified by a particular value of this index is associated with the same diffServActionEntry as identified by the same value of diffServActionIndex.

OBJECT-TYPE

This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

Table for class map.

OBJECT-TYPE

Entry for class map.

OBJECT-TYPE

An index that uniquely identifies an entry in this table.

OBJECT-TYPE

The name of this entry.

OBJECT-TYPE

The description of this entry.

OBJECT-TYPE

The map match type of this entry.

OBJECT-TYPE

The octet string containes the type of class map element indexes. Two octets which are represented in network order express one type of the class map element index in network order and it maps the index of diffServClassMapElementIndexList in order. When the type is macAce(1), the maping index of diffServClassMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of diffServClassMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of diffServClassMapElementIndexList is the diffServAclEntry. When the type is ipv6Ace(4), the maping index of diffServClassMapElementIndexList is the diffServIpv6AceEntry.

OBJECT-TYPE

The octet string containes the class map element indexes. Two octets express one index and it is represented in network order. This index list indicates the particular class map elements which belong to this table. The class map element uses type to indicate diffServAclEntry, the diffServIpAceEntry or diffServMacAceEntry. The type is two octet specified in diffServClassMapElementIndexTypeList in order. When the type is macAce(1), the maping index of diffServClassMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of diffServClassMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of diffServClassMapElementIndexList is the diffServAclEntry. When type is ipv6Ace(4), the maping index of diffServClassMapElementIndexList is the diffServIpv6AceEntry.

OBJECT-TYPE

This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-IDENTITY

OBJECT-TYPE

Index for attachment control. Specifies the class map as the target to relate with class map elements. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex.

OBJECT-TYPE

Element Index for attachment control. Specifies the type of class map element to relate with the class map. When type is macAce(1), the index of diffServClassMapAttachCtlElementIndex is the index of diffServMacAceEntry. When the type is ipAce(2), the index of diffServClassMapAttachCtlElementIndex is the index of diffServIpAceEntry. When the type is acl(3), the index of diffServClassMapAttachCtlElementIndex is the index of diffServAclEntry. When type is ipv6Ace(4), the index of diffServClassMapAttachCtlElementIndex is the index of diffServIpv6AceEntry.

OBJECT-TYPE

Element Index for attachment control. Specifies the class map element related with the class map. The class map element uses type to indicate diffServAclEntry, the diffServIpAceEntry or diffServMacAceEntry. The type is specified in diffServClassMapAttachCtlElementIndexType. When the type is macAce(1), the maping index of diffServClassMapElementIndexList is the diffServMacAceEntry. When the type is ipAce(2), the maping index of diffServClassMapElementIndexList is the diffServIpAceEntry. When the type is acl(3), the maping index of diffServClassMapElementIndexList is the diffServAclEntry. When type is ipv6Ace(4), the maping index of diffServClassMapElementIndexList is the diffServIpv6AceEntry.

OBJECT-TYPE

Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular class map element is attached to a particular class map. When setting this object to detach(3) to begin the not attached operation, then a particular class map element is not attached to a particular class map. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1). The value of a particular class map is specified in the AclAttachCtlTargetIndex. The class map element is specified by diffServClassMapAttachCtlElementIndexType and diffServClassMapAttachCtlElementIndex.

OBJECT-TYPE

Table for ACL.

OBJECT-TYPE

Entry for ACL.

OBJECT-TYPE

An index that uniquely identifies an entry in the ACL table.

OBJECT-TYPE

The name of this entry.

OBJECT-TYPE

The type of this entry. When the value of ACL type is modified, then the ACEs in the diffServAclAceIndexList of this entry will be auto-removed, and this entry will be auto- unbound from the diffServPortTable and the diffServClassMapTable.

OBJECT-TYPE

The octet string containes the ACE indexes. Two octets express one index and it is represented in network order. This index list indicates the particular ACEs which belong to this table. The ACE uses type to indicate the diffServMacAceEntry, the diffServIpAceEntry, the diffServIpv6AceEntry or the diffServArpAceEntry. The type is specified in diffServAclType. When the type is mac(1), the index of diffServAclAceIndexList is the diffServMacAceEntry. When the type is ipstandard(2) or ipextended(3), the index of diffServAclAceIndexList is the diffServIpAceEntry. When the type is ipv6standard(4) or ipv6extended(5), the index of diffServAclAceIndexList is the diffServIpv6AceEntry. When the type is arp(6), the index of diffServAclAceIndexList is the diffServArpAceEntry.

OBJECT-TYPE

This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-IDENTITY

OBJECT-TYPE

Index for attachment control. Specifies the ACL as the target to relate with the IP ACE, the MAC ACE or IPv6 ACE. The ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.

OBJECT-TYPE

Type for attachment control. Specifies the type of diffServAclAttachCtlAceIndex to relate with the diffServAclAttachCtlIndex. When the type is macAce(1), the index of diffServAclAceIndexList is the diffServMacAceEntry. When the type is ipAce(2), the index of diffServAclAceIndexList is the diffServIpAceEntry. When the type is ipv6Ace(3), the index of diffServAclAceIndexList is the diffServIpv6AceEntry. When the type is arpAce(4), the index of diffServAclAceIndexList is the diffServArpAceEntry.

OBJECT-TYPE

Index for attachment control. Specifies the ACE to relate with the diffServAclAttachCtlIndex. When diffServAclAttachCtlAceType is macAce(1), the value of diffServAclAttachCtlIndex is the diffServMacAceEntry. When diffServAclAttachCtlAceType is ipAce(2), the value of diffServAclAttachCtlIndex is the diffServIpAceEntry. When diffServAclAttachCtlAceType is ipv6Ace(3), the value of diffServAclAttachCtlIndex is the diffServIpv6AceEntry. When diffServAclAttachCtlAceType is arpAce(4), the value of diffServAclAttachCtlIndex is the diffServArpAceEntry.

OBJECT-TYPE

Action for attachment control. When setting this object to attach(2) to begin the attaching operation, a particular ACE is attached to a particular ACL. When setting this object to detach(3) to begin the not attached operation, then a particular ACE is not attached to a particular ACL. When the action is finshed whether successfully or not, or no action is taken, the value of this object always is noAction(1), The value of a particular ACL is specified in the diffServAclAttachCtlAceType and diffServAclAttachCtlAceIndex.

OBJECT-TYPE

Table for IP ACE.

OBJECT-TYPE

Entry for IP ACE.

OBJECT-TYPE

An index that uniquely identifies an entry in the IP ACE table.

OBJECT-TYPE

The specified IP ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field of this entry will be set 0.

OBJECT-TYPE

Indicates the action to be taken if a packet matches this ACE.

OBJECT-TYPE

The specified source IP address. The packet's source address is AND-ed with the value of IpAceSourceIpAddrBitmask and then compared against the value of this object.

OBJECT-TYPE

The specified source IP address mask. The packet's source address is AND-ed with the value of IpAceSourceIpAddr and then compared against the value of this object.

OBJECT-TYPE

The specified destination IP address. The packet's destination address is AND-ed with the value of diffServIpAceDestIpAddrBitmask and then compared against the value of this object. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

The specified destination IP address mask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value of 0 matches every IP packet. The object=256 means 'any'. For example: 0 is IP, 1 is ICMP, 2 is IGMP, 4 is IP in IP encapsulation, 6 is TCP, 9 is IGRP, 17 is UDP, 47 is GRE, 50 is ESP, 51 is AH, 88 is IGRP, 89 is OSPF, 94 is KA9Q/NOS compatible IP over IP, 103 is PIMv2, 108 is PCP. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

Specifies the IP precedence value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 8. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

Specifies the DSCP value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 64. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means no comparison is to be made with the source TCP/UDP port number. equal(2), which is used the diffServIpAceSourcePortBitmask and the diffServIpAceMinSourcePort to match against. range(3),which is used the diffServIpAceMinSourcePort and the diffServIpAceMaxSourcePort to match against. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

If the diffServIpAceSourcePortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

If the diffServIpAceSourcePortOp is equal(2), this indicates the bitmask of the diffServIpAceMinSourcePort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. equal(2), which is used the diffServIpAceSourcePortBitmask and the diffServIpAceMinDestPort to match against. range(3),which is used the diffServIpAceMinDestPort and the diffServIpAceMaxDestPort to match against. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

If the diffServIpAceDestPortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

If the diffServIpAceDestPortOp is equal(2), this indicates the bitmask of the diffServIpAceMinDestPort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

Indicates how the control flags of TCP packets are to be compared. diffServIpAceControlCode is AND-ed with diffServIpAceControlCodeBitmask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

Indicates how the control flags of TCP packets are to be compared. It can be used to check multiple flags of the FIN, SYN, RST, PSH, ACK, URG by the sum of FIN=1, SYN=2, RST=4, PSH=8, ACK=16, URG=32. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).

OBJECT-TYPE

This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

Indicates how a packet's VID is to be compared.

OBJECT-TYPE

If the diffServIpAceVidOp is equal(2), this indicate the VLAN ID data value.

OBJECT-TYPE

If the diffServIpAceVidOp is equal(2), this indicate the VLAN ID bitmask value.

OBJECT-TYPE

Table for MAC ACE.

OBJECT-TYPE

Entry for MAC ACE.

OBJECT-TYPE

An index that uniquely identifies an entry in the MAC ACE table.

OBJECT-TYPE

Indicates the action to be taken if a packet matches this ACE.

OBJECT-TYPE

Used to check the packet format of the packets. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).

OBJECT-TYPE

Indicates the 48-bit source MAC address. The specified source MAC of the packet. The packet's source MAC address is AND-ed with the value of diffServMacAceSourceMacAddrBitmask and then compared against the value of this object.

OBJECT-TYPE

The specified source MAC address mask.

OBJECT-TYPE

Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND-ed with the value of diffServMacAceDestMacAddrBitmask and then compared against the value of this object.

OBJECT-TYPE

The specified destination MAC address mask.

OBJECT-TYPE

Indicates how a packet's VID is to be compared. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).

OBJECT-TYPE

Indicates the lower bound of the VID value range if the diffServMacAceVidOp is range(3).

OBJECT-TYPE

The bit mask of the VID. The default value is 0.

OBJECT-TYPE

Indicates how a packet's ether type is to be compared.

OBJECT-TYPE

The bit mask of Ether type. The default value is 0.

OBJECT-TYPE

Indicates the lower bound of the ether type value range if the diffServMacAceEtherTypeOp is range(3).

OBJECT-TYPE

This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

Indicates how a packet's CoS is compared. If the object type of diffServMacAceCosOp is equal(2), diffServMacAceMinCos indicates the CoS value for comparing, and diffServMacAceCosBitmask is used as the bitmask of the CoS value. If the object type of diffServMacAceCosOp is range(3), diffServMacAceMinCos should be used as the lower bound of the CoS value.

OBJECT-TYPE

Indicates the bitmask of the CoS value if the object type of diffServMacAceCosOp is equal(2). The default value is 0.

OBJECT-TYPE

If the object type of diffServMacAceCosOp is equal(2), diffServMacAceMinCos indicates the CoS value for comparing. If the object type of diffServMacAceCosOp is range(3), diffServMacAceMinCos indicates the lower bound of the CoS value.

OBJECT-TYPE

Only configurable while ethertype is specified to IPv4 diffServMacAceEtherTypeOp is equal(2) diffServMacAceMinEtherType is 0x0800 diffServMacAceEtherTypeBitmask is 0xffff Indicate the IP precedence value, 8 mean ignore.

OBJECT-TYPE

This object is used to seperate the data protocol under a tunnel protocol. Now it is only used while ethertype is configured as following diffServMacAceEtherTypeOp is equal(2) diffServMacAceMinEtherType is 0x8864 diffServMacAceEtherTypeBitmask is 0xffff

OBJECT-TYPE

Table for action.

OBJECT-TYPE

Entry for action.

OBJECT-TYPE

An index that uniquely identifies an entry in the action table.

OBJECT-TYPE

The bitmap value used to identify which action capabilities are enabled on the entry. The actionPktNewPri and actionPktNewDscp can not be enabled at the same time on the entry. The actionRedPktNewDscp and actionRedDrop can not be enabled at the same time on the entry.

OBJECT-TYPE

Specifies the new priority value for the packet when the action is satisfied. If the actionPktNewPri bit of the diffServActionList is not enabled, this object can not be set.

OBJECT-TYPE

Specifies the inner priority value for the packet when the action is satisfied. If the actionPktNewPhb bit of the diffServActionList is not enabled, this object can not be set.

OBJECT-TYPE

This object is used to create a new row, modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

Specifies the new DSCP value for the packet when the action is satisfied. If the actionPktNewDscp bit of the diffServActionList is not enabled, this object can not be set.

OBJECT-TYPE

Table for meter.

OBJECT-TYPE

Entry for meter.

OBJECT-TYPE

An entry that describes a single set of token bucket parameters.

OBJECT-TYPE

The Metering algorithm associated with the Token Bucket parameters. The zeroDotZero indicates this is unknown.

OBJECT-TYPE

The token-bucket rate, in kilobits per second (kbps).

OBJECT-TYPE

This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

Table for IPv6 ACE.

OBJECT-TYPE

Entry fo IPv6 ACE.

OBJECT-TYPE

An index that uniquely identifies an entry in the IPv6 table.

OBJECT-TYPE

The specified IP v6 ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field of this entry will be set 0.

OBJECT-TYPE

Indicates the action to be taken if a packet matches this ACE.

OBJECT-TYPE

Specifies the source IPv6 address.

OBJECT-TYPE

The length (in bits) associated with the source IPv6 address prefix of this entry.

OBJECT-TYPE

Specifies the destination IPv6 address. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).

OBJECT-TYPE

The length (in bits) associated with the destination IPv6 address prefix of this entry. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).

OBJECT-TYPE

Specifies the next header to match against. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).

OBJECT-TYPE

Specifies the DSCP value to match against. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).

OBJECT-TYPE

This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has the value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has the value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has the value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the source TCP/UDP port number. equal(2), which uses the diffServIpv6AceSourcePort and diffServIpv6AceSourcePortBitmask to match against. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).

OBJECT-TYPE

If the diffServIpv6AceSourcePortOp is equal(2), this indicates the TCP/UDP port number value.

OBJECT-TYPE

If the diffServIpv6AceSourcePortOp is equal(2), this indicates the bitmask of the diffServIpv6AceSourcePort.

OBJECT-TYPE

Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. equal(2), which uses the diffServIpv6AceDestPort and diffServIpv6AceDestPortBitmask to match against. This object may not be modified if the associated diffServIpv6AceType object is equal to standard(1).

OBJECT-TYPE

If the diffServIpv6AceDestPortOp is equal(2), this indicates the TCP/UDP port number value.

OBJECT-TYPE

If the diffServIpv6AceDestPortOp is equal(2), this indicates the bitmask of the diffServIpv6AceDestPort.

OBJECT-TYPE

The conceptual table of all of diffServArpAceEntry.

OBJECT-TYPE

The conceptual row for diffServArpAceTable.

OBJECT-TYPE

The unique index of an ACE within an ACL.

OBJECT-TYPE

Indicates the action to be taken if a packet matches this ACE. This object cannot not be configured when the status of the entry, diffServArpAceStatus, is active(1).

OBJECT-TYPE

Indicates the packet type to be taken if a packet matches this ACE. This object can not be configured when the status of the entry, diffServArpAceStatus, is active(1).

OBJECT-TYPE

The specified source ARP address. The packet's source address is AND'ed with the value of diffServArpAceSourceIpAddrBitmask and then compared against the value of this object. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1).

OBJECT-TYPE

The specified source ARP address mask. The packet's destination address is AND'ed with the value of diffServArpAceSourceIpAddr and then compared against the value of this object.

OBJECT-TYPE

The specified destination IP address. The packet's destination address is AND'ed with the value of diffServArpAceDestIpAddrBitmask and then compared against the value of this object.

OBJECT-TYPE

The specified destination IP address mask.

OBJECT-TYPE

Indicates the 48-bit destination MAC address. The specified source MAC of the packet. The packet's source MAC address is AND'ed with the value of aceArpSourceMacAddrBitmask and then compared against the value of this object. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1).

OBJECT-TYPE

The specified source MAC address mask. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1).

OBJECT-TYPE

Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND'ed with the value of aceArpDestMacAddrBitmask and then compared against the value of this object. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1).

OBJECT-TYPE

The specified destination MAC address mask. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1).

OBJECT-TYPE

Indicates whether to log messages against the packets. This object cannot be configured when the status of the entry, diffServArpAceStatus, is active(1).

OBJECT-TYPE

The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

The conceptual table of all of diffServArpEntry.

OBJECT-TYPE

The conceptual row for diffServArpTable.

OBJECT-TYPE

The name of an ACL. Within a feature, a unique name is used to identify the list to which the entry belongs in the device.

OBJECT-TYPE

Table for differentiated services hardware counter on each port.

OBJECT-TYPE

Entry for differentiated services hardware counter on each port.

OBJECT-TYPE

This object is the interface index of diffServPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Indicates a particular direction of traffic.

OBJECT-TYPE

An index that uniquely identifies an entry in the ACL table.

OBJECT-TYPE

An index that uniquely identifies an entry of an ACL. This entry might be a compressed ACE (which index is bigger than SYS_ADPT_MAX_NBRS_OF_ACE_OF_SYSTEM) with multiple user configured ACEs, and the index of compressed ACE will not show in ACE table.

OBJECT-TYPE

Specifies the hardware counter of an ACE entry.

OBJECT-TYPE

Table for policy map of each port.

OBJECT-TYPE

Entry for diffServPolicyMapPortTable.

OBJECT-TYPE

This object is the interface index of DiffServPolicyMapPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Indicates this policy map effect to which direction of traffic.

OBJECT-TYPE

Specifies the policy map index binded to the interface. The policy map identified by a particular value of this index is associated with the same DiffServPolicyMapEntry as identified by the same value of diffServPolicyMapIndex.

OBJECT-TYPE

This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

Table for specifies access group for ACL on each port.

OBJECT-TYPE

Entry for diffServAccessGroupTable.

OBJECT-TYPE

This object is the interface index of diffServAccessGroupEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB. If support global ACL, using the specific ifindex(65535).

OBJECT-TYPE

Indicates this access group effect to which direction of traffic.

OBJECT-TYPE

Specifies the access group type, only support bind one ACL per type on a port.

OBJECT-TYPE

Specifies the ACL index apply to this access group. The index uniquely identifies an entry in diffServAclTable.

OBJECT-TYPE

The name of the time range entry bound to the access group. This object should be equal to one of the timeRangeName objects in timeRangeTable.

OBJECT-TYPE

The acl counter enable status of this access group.

OBJECT-TYPE

This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active', which indicates that the conceptual row is available for use by the managed device; - 'notInService', which indicates that the conceptual row exists in the agent, but is unavailable for use by the managed device (see NOTE below); - 'notReady', which indicates that the conceptual row exists in the agent, but is missing information necessary in order to be available for use by the managed device; - 'createAndGo', which is supplied by a management station wishing to create a new instance of a conceptual row and to have its status automatically set to active, making it available for use by the managed device; - 'createAndWait', which is supplied by a management station wishing to create a new instance of a conceptual row (but not make it available for use by the managed device); and, - 'destroy', which is supplied by a management station wishing to delete all of the instances associated with an existing conceptual row. Whereas five of the six values (all except 'notReady') may be specified in a management protocol set operation, only three values will be returned in response to a management protocol retrieval operation: 'notReady', 'notInService' or 'active'. That is, when queried, an existing conceptual row has only three states: it is either available for use by the managed device (the status column has value 'active'); it is not available for use by the managed device, though the agent has sufficient information to make it so (the status column has value 'notInService'); or, it is not available for use by the managed device, and an attempt to make it so would fail because the agent has insufficient information (the state column has value 'notReady'). For a detailed description of this object, please refer to SNMPv2-TC MIB.

OBJECT-TYPE

The conceptual table of all of DiffServTcamEntry.

OBJECT-TYPE

The conceptual row for diffServTcamTable.

OBJECT-TYPE

This object identifies the switch within the system for which this entry contains information.

OBJECT-TYPE

The device id of the specified unit.

OBJECT-TYPE

The TCAM pool index of the specified unit and device.

OBJECT-TYPE

The bitmap value used to identify which functions supported on this pool.

OBJECT-TYPE

The total number of TCAM pool entry.

OBJECT-TYPE

The free number of TCAM pool entry.

OBJECT-TYPE

The used number of TCAM pool entry.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This controls whether private VLAN is enabled.

OBJECT-TYPE

Contains the settings for private VLAN Session.

OBJECT-TYPE

A conceptual row in the privateVlanSession table.

OBJECT-TYPE

The session ID that may specifiy certain entry in the table which contains private VLAN session information.

OBJECT-TYPE

This is the list of uplink ports for a session of private VLAN. They should not overlap with the privateVlanSessionPortDownlink of the same session, and they also should not overlap with the privateVlanSessionPortUplink and the privateVlanSessionPortDownlink of other session.

OBJECT-TYPE

This is the list of downlink ports for a session of private VLAN. They should not overlap with the privateVlanSessionPortUplink of the same session, and they also should not overlap with the privateVlanSessionPortUplink and the privateVlanSessionPortDownlink of other session.

OBJECT-TYPE

Set this to valid(1) to create an entry. Sets this to invalid(2) to destroy an entry.

OBJECT-TYPE

Sets this to blocking(2) to deny the traffic of uplink ports between different sessions. Set this to forwarding(1) to allow the traffic of uplink ports between different sessions.

OBJECT-IDENTITY

OBJECT-TYPE

The port security(MAC binding) Table.

OBJECT-TYPE

The entry of portSecPortTable.

OBJECT-TYPE

The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.

OBJECT-TYPE

Set enabled(1) to enable port security and set disabled(2) to disable port security.

OBJECT-TYPE

The corresponding actions that will take place when a port is under intrusion, when this variable is set to none(1), no action will be performed, when this variable is set to trap(2), a swPortSecurityTrap trap will be sent, when this variable is set to shutdown(3), the port will shutdown, when this variable is set to trapAndShutdown(4), a swPortSecurityTrap will be sent and the port will shutdown.

OBJECT-TYPE

The maximun number of MAC addresses that will be learned and locked. When we change the value of this variable, if the portSecPortStatus is enabled, we will discard all secure MAC and begin to learn again, until the number of MAC has reached this value, and only the secure MAC addresses can enter this port. If the portSecPortStatus is disabled, we will begin to learn the MAC, and auto enabled the portSecPortStatus when the MAC has reached this value.

OBJECT-TYPE

Set enabled(1) to start sticky MAC feature for preventing dynamic secure MAC addresses port move. Set disabled(2) to stop sticky MAC feature.

OBJECT-IDENTITY

OBJECT-TYPE

The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB. Specifies the interface to convert the learnt secured MAC address into manual configured. '0' represents that no interface is specified.

OBJECT-TYPE

Set action(2) to convert the learnt secured MAC address into manual configured. When action finsh or no action, the value of this object is noAction(1).

OBJECT-IDENTITY

OBJECT-TYPE

Aauthentication port number for RADIUS server. When specified radius server do not set aauthentication port number, this value is used.

OBJECT-TYPE

Accounting port number of RADIUS server. When specified radius server do not set accounting port number, this value is used.

OBJECT-TYPE

Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string. When specified radius server do not set key, this this value is used.

OBJECT-TYPE

Maximum number of retransmissions for RADIUS. When specified radius server do not set maximum number of retransmissions, this value is used.

OBJECT-TYPE

Timeout for RADIUS. When specified radius server do not set timeout, this value is used.

OBJECT-TYPE

Sets enabled(1) to enable radsec for Radius and sets disabled(2) to disable radsec for Radius.

OBJECT-TYPE

The table for RADIUS server.

OBJECT-TYPE

The conceptual row for radiusServerTable.

OBJECT-TYPE

The RADIUS server index in the table.

OBJECT-TYPE

IP address of a RADIUS server.

OBJECT-TYPE

Authentication port number of RADIUS server.

OBJECT-TYPE

Accounting port number of RADIUS server.

OBJECT-TYPE

Key for RADIUS. This variable can only be written. When this variable is read, it always returns a zero-length string.

OBJECT-TYPE

Timeout for RADIUS.

OBJECT-TYPE

Timeout for RADIUS.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-TYPE

Sets enabled(1) to enable radsec for Radius and sets disabled(2) to disable radsec for Radius.

OBJECT-IDENTITY

OBJECT-TYPE

TCP port number of TACACS+ server. When specified TACACS+ server do not set TCP port number, this this value is used.

OBJECT-TYPE

The encryption key used to encrpt the traffic between client and TACACS+ server. Do not use blank spaces in the string. This variable can only be set. When this variable is read, it always returns a zero-length string.When specified TACACS+ server do not set the encryption key , this this value is used.

OBJECT-TYPE

The table for TACACS+ server.

OBJECT-TYPE

The conceptual row for tacacsPlusServerTable.

OBJECT-TYPE

TACACS+ server index.

OBJECT-TYPE

TCP port number of a TACACS+ server.

OBJECT-TYPE

The encryption key used to encrpt the traffic between client and TACACS+ server. Do not use blank spaces in the string. This variable can only be set. When this variable is read, it always returns a zero-length string.

OBJECT-TYPE

Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.

OBJECT-TYPE

Type of IP address of a TACACS+ server. Only ipv4(1) and ipv6(2) types are supported.

OBJECT-TYPE

IP address of a TACACS+ server.

OBJECT-IDENTITY

OBJECT-TYPE

The status of Secure Shell Server. Set this value to enabled(1) to enable SSH server, set this value to disabled(2) to disable the SSH server.

OBJECT-TYPE

The major version of the SSH Server.

OBJECT-TYPE

The minor version of the SSH Server.

OBJECT-TYPE

The time interval that the router waits for the SSH client to respond. The range is 1-120.

OBJECT-TYPE

The number of attempts after which the interface is reset. The range is 1-5.

OBJECT-TYPE

The table for Secure Shell Connection.

OBJECT-TYPE

The conceptual row for sshConnInfoTable.

OBJECT-TYPE

The connection ID of the Secure Shell Connection.

OBJECT-TYPE

The SSH major version.

OBJECT-TYPE

The SSH minor version.

OBJECT-TYPE

The SSH connection State. negotiationStart(1) means the SSH is in its negotiation start state, authenticationStart(2) means the SSH is in authentication start state, sessionStart(3) means the SSH is in session start State.

OBJECT-TYPE

The user name of the connection.

OBJECT-TYPE

Set the variable to disconnect the connection, noDisconnect(1) will always be obtained when reading this variable.

OBJECT-TYPE

The encryption type of the SSH.

OBJECT-TYPE

The RSA host key segment 1.

OBJECT-TYPE

The RSA host key segment 2.

OBJECT-TYPE

The RSA host key segment 3.

OBJECT-TYPE

The RSA host key segment 4.

OBJECT-TYPE

The RSA host key segment 5.

OBJECT-TYPE

The RSA host key segment 6.

OBJECT-TYPE

The RSA host key segment 7.

OBJECT-TYPE

The RSA host key segment 8.

OBJECT-TYPE

This variable is for host key generating. For the set behavior: Set it to genRsaKey(2) to generate the RSA host key. For the get behavior: You will get genRsaKey(2) when the key gen action is in progress. Otherwise, you will get noGen(1).

OBJECT-TYPE

The result of the last KeyGen status. if no key gen action has been performed. you will get unknown(1) status.

OBJECT-TYPE

To save host key from memory to flash. For the set behavior: Set it to save(2) to perform the save operation. For the get behavior: You will get save(1) when the save action is in progress. Otherwise, you will get noSave(1).

OBJECT-TYPE

The result of the last savekey status. If no save action has been performed, you will get unknown(1) status.

OBJECT-TYPE

To delete the host key. For the set behavior: Set it to delRsaKey(2) to delete the RSA host key. For the get behavior: You will get delRsaKey(2) when the delete operation is in progress. Otherwise, you will get noDel(1).

OBJECT-TYPE

The conceptual table of all of sshUserEntry.

OBJECT-TYPE

The conceptual row for sshUserTable.

OBJECT-TYPE

User Name.

OBJECT-TYPE

The RSA user key segment 1.

OBJECT-TYPE

The RSA user key segment 2.

OBJECT-TYPE

The RSA user key segment 3.

OBJECT-TYPE

The RSA user key segment 4.

OBJECT-TYPE

The RSA user key segment 5.

OBJECT-TYPE

The RSA user key segment 6.

OBJECT-TYPE

The RSA user key segment 7.

OBJECT-TYPE

The RSA user key segment 8.

OBJECT-TYPE

To delete the user key. For the set behavior: Set it to delRsaKey(2) to delete the RSA user key. For the get behavior: You will get delRsaKey(2) when the delete operation is in progress. Otherwise, you will get noDel(1).

OBJECT-IDENTITY

OBJECT-TYPE

A list of IP address entries.

OBJECT-TYPE

This entry includes an IP address range which the system will allow to connect to this device through SNMP.

OBJECT-TYPE

The type of IP address filter. Only supports IPv4 and IPv6 address types.