Dell-Vendor-MIB
- Registered at
- 1.3.6.1.4.1.674.10895
- Last updated
- 2005-01-15 00:00
- Organization
- Dell Inc.
- Namespace
- dell
- Source file
Dell-Vendor-MIB- Digest
sha256:8f6d07f58afbd6d7a3464ff00ae32574891b868e4ada42685021ca9cbf6f86f9
Description
The private MIB module definition for the Dell PowerConnect Devices. This MIB allows PowerConnect devices to be integrated into Dell ITA management system.
Contact
support.dell.com
Imports
| From | Symbols |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DisplayString, RowStatus, TEXTUAL-CONVENTION |
Imported by
4 module(s) in this corpus import this one.
Load order
Every file a consumer needs in order to load this module, dependencies first.
Dell-Vendor-MIB SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
Under this module's arcs
Where the registration tree carries on below this module.
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| EnvMonState TEXTUAL-CONVENTION Represents the state of a device being monitored. Valid values are: normal(1): the environment is good, such as low temperature. warning(2): the environment is bad, such as temperature above normal operation range but not too high. critical(3): the environment is very bad, such as temperature much higher than normal operation limit. shutdown(4): the environment is the worst, the system should be shutdown immediately. notPresent(5): the environmental monitor is not present, such as temperature sensors do not exist. notFunctioning(6): the environmental monitor does not function properly, such as a temperature sensor generates a abnormal data like 1000 C. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| dell OBJECT-IDENTITY | 1.3.6.1.4.1.674 | |||
| dellLan OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895 | |||
| dellVendorMIBObjects OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.3000.1 | |||
| hardware OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.3000.1.2 | |||
| productIdentification OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.3000.1.2.100 | |||
| productIdentificationDisplayName OBJECT-TYPE Name of this product for display purposes. | 1.3.6.1.4.1.674.10895.3000.1.2.100.1 | DisplayString | read-only | current |
| productIdentificationDescription OBJECT-TYPE A short description of this product such as: Ethernet Router Switch. | 1.3.6.1.4.1.674.10895.3000.1.2.100.2 | DisplayString | read-only | current |
| productIdentificationVendor OBJECT-TYPE The name of the product manufacturer, such as: Dell Inc. | 1.3.6.1.4.1.674.10895.3000.1.2.100.3 | DisplayString | read-only | current |
| productIdentificationVersion OBJECT-TYPE The version of this product. | 1.3.6.1.4.1.674.10895.3000.1.2.100.4 | DisplayString | read-only | current |
| productIdentificationBuildNumber OBJECT-TYPE The software build number of the product. | 1.3.6.1.4.1.674.10895.3000.1.2.100.5 | DisplayString | read-only | current |
| productIdentificationURL OBJECT-TYPE The URL of the web-based application to manage this device, should the device provide one. The format of the value held by this object is: http://<device IP address>. | 1.3.6.1.4.1.674.10895.3000.1.2.100.6 | DisplayString | read-only | current |
| productIdentificationDeviceNetworkName OBJECT-TYPE Device Name. | 1.3.6.1.4.1.674.10895.3000.1.2.100.7 | DisplayString | read-only | current |
| productIdentificationPerUnitTable OBJECT-TYPE Identification specific to product instance and, in case of stackable products, per unit. If the product is not stackable, it will be considered a stack of one unit and therefore this table will contain one conceptual row only. | 1.3.6.1.4.1.674.10895.3000.1.2.100.8 | not-accessible | current | |
| productIdentificationPerUnitEntry OBJECT-TYPE This row applies to a unit in a stackable product. | 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1 | not-accessible | current | |
| productIdentificationPerBoxIndex OBJECT-TYPE The index of the stack unit to which this conceptual row corresponds. Note that the index will be the same index as the index of a 'chassis' physical entity in the entity MIB of the product. | 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.1 | INTEGER (1..2147483647) | read-only | current |
| productIdentificationSerialNumber OBJECT-TYPE Serial number of the product. | 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.2 | DisplayString | read-only | current |
| productIdentificationAssetTag OBJECT-TYPE Asset tag of the product. | 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.3 | DisplayString | read-only | current |
| productIdentificationServiceTag OBJECT-TYPE Service tag of the product. | 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.4 | DisplayString | read-only | current |
| productIdentificationBootromVersion OBJECT-TYPE The boot image version of the product. | 1.3.6.1.4.1.674.10895.3000.1.2.100.8.1.6 | DisplayString | read-only | current |
| productIdentificationBannerMotd OBJECT-TYPE Use to assign CLI attention banner. The banner should support 1500 characters. | 1.3.6.1.4.1.674.10895.3000.1.2.100.9 | DisplayString (SIZE(0..1500)) | read-write | current |
| productIdentificationBannerMotdAckMode OBJECT-TYPE If enable is selected, user will be required to acknowledge the banner displayed on the console. The user would have to type y or n to continue to the login prompt. If n is typed, the session is terminated and no further communication is allowed on that session. However, serial connection will not get terminated if user does not enter y. Use disable option to disable banner acknowledge. | 1.3.6.1.4.1.674.10895.3000.1.2.100.10 | INTEGER {enable(1), disable(2)} | read-write | current |
| productStatus OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.3000.1.2.110 | |||
| productStatusGlobalStatus OBJECT-TYPE Current status of the product.This is a rollup for the entire product. The status is intended to give initiative to a snmp monitor to get further data when this status is abnormal. This variable can take the following values: 3: OK If fans and power supplies are functioning and the system did not reboot because of a HW watchdog failure or a SW fatal error condition. 4: Non-critical If at least one power supply is not functional or the system rebooted at least once because of a HW watchdog failure or a SW fatal error condition. 5: Critical If at least one fan is not functional, possibly causing a dangerous warming up of the device. | 1.3.6.1.4.1.674.10895.3000.1.2.110.1 | INTEGER {ok(3), non-critical(4), critical(5)} | read-only | current |
| productStatusLastGlobalStatus OBJECT-TYPE The status before the current status which induced an initiative to issue a global status change trap. | 1.3.6.1.4.1.674.10895.3000.1.2.110.2 | INTEGER {ok(3), non-critical(4), critical(5)} | read-only | current |
| productStatusTimeStamp OBJECT-TYPE The last time that the product global status has been updated. The time will be given in TimeTicks | 1.3.6.1.4.1.674.10895.3000.1.2.110.3 | TimeTicks | read-only | current |
| productStatusGetTimeOut OBJECT-TYPE Suggested time out value in milliseconds for how long the SNMP getter should wait while attempting to poll the product SNMP service. | 1.3.6.1.4.1.674.10895.3000.1.2.110.4 | INTEGER (1..1000) | read-only | current |
| productStatusRefreshRate OBJECT-TYPE Rate in seconds at which the SNMP service cached data is being updated. | 1.3.6.1.4.1.674.10895.3000.1.2.110.5 | INTEGER (1..100) | read-only | current |
| productStatusGeneratingTrapsFlag OBJECT-TYPE Indicates if this SNMP service is generating SNMP Traps. This variable can take the following values: 1: true - The device is capable and currently configured to generate traps if necessary. 2: false - The device is not capable of generating traps. 3: disabled - The device is capable but not configured to generate traps. | 1.3.6.1.4.1.674.10895.3000.1.2.110.6 | INTEGER {true(1), false(2), disabled(3)} | read-only | current |
| productStatusEnvironment OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.3000.1.2.110.7 | |||
| envMonFanStatusTable OBJECT-TYPE The table of fan status maintained by the environmental monitor. Not Supported by Dell Modular Blade Server switches. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1 | not-accessible | current | |
| envMonFanStatusEntry OBJECT-TYPE An entry in the fan status table, representing the status of the associated fan maintained by the environmental monitor. Not Supported by Dell Modular Blade Server switches. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1 | not-accessible | current | |
| envMonFanStatusIndex OBJECT-TYPE Unique index for the fan being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning. Not Supported by Dell Modular Blade Server switches. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1.1 | INTEGER (1..2147483647) | read-only | current |
| envMonFanStatusDescr OBJECT-TYPE Textual description of the fan being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry. Not Supported by Dell Modular Blade Server switches. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1.2 | DisplayString (SIZE(0..32)) | read-only | current |
| envMonFanState OBJECT-TYPE The mandatory state of the fan being instrumented. Not Supported by Dell Modular Blade Server switches. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.1.1.3 | EnvMonState | read-only | current |
| envMonSupplyStatusTable OBJECT-TYPE The table of power supply status maintained by the environmental monitor card. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2 | not-accessible | current | |
| envMonSupplyStatusEntry OBJECT-TYPE An entry in the power supply status table, representing the status of the associated power supply maintained by the environmental monitor card. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1 | not-accessible | current | |
| envMonSupplyStatusIndex OBJECT-TYPE Unique index for the power supply being instrumented. This index is for SNMP purposes only, and has no intrinsic meaning. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.1 | INTEGER (0..2147483647) | read-only | current |
| envMonSupplyStatusDescr OBJECT-TYPE Textual description of the power supply being instrumented. This description is a short textual label, suitable as a human-sensible identification for the rest of the information in the entry. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.2 | DisplayString (SIZE(0..32)) | read-only | current |
| envMonSupplyState OBJECT-TYPE The mandatory state of the power supply being instrumented. | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.3 | EnvMonState | read-only | current |
| envMonSupplySource OBJECT-TYPE The power supply source. unknown - Power supply source unknown ac - AC power supply dc - DC power supply externalPowerSupply - External power supply internalRedundant - Internal redundant power supply | 1.3.6.1.4.1.674.10895.3000.1.2.110.7.2.1.4 | INTEGER {unknown(1), ac(2), dc(3), externalPowerSupply(4), internalRedundant(5)} | read-only | current |
| dellVendorNotifications OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.3000.2 | |||
| dellVendorTraps OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.3000.2.1 | |||
| dellVendorTrapsPrefix OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.3000.2.1.0 | |||
| dellLanStandard OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.5000 | |||
| dellLanCommon OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.5000.1 | |||
| dellLanExtension OBJECT-IDENTITY | 1.3.6.1.4.1.674.10895.5000.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| productStatusGlobalStatusChange NOTIFICATION-TYPE This trap is sent when the product global status changes. | 1.3.6.1.4.1.674.10895.3000.2.1.0.1 | current |