MIBs Depot

DataAire-dap4-al-MIB

Last updated
2011-07-12 08:50
Organization
Data Aire
Revisions
2011-07-12 08:50
Namespace
dataaire
Source file
DataAire-dap4-al-MIB
Digest
sha256:cb5ea96c7e4be5b181daac58420534dc697b6cbdb6969bbda3ee5f2456a32df7

Description

This is the MIB module for the dap4_al device.

Contact

Data Aire 230 West Blueridge Ave Orange, CA Tel: 1-800-347-2473 E-mail: sales@dataaire.com

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-MIBsysContact, sysLocation, sysName
SNMPv2-SMIInteger32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DataAire-dap4-al-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
carel
OBJECT-IDENTITY
1.3.6.1.4.1.9839
systm
OBJECT-IDENTITY
1.3.6.1.4.1.9839.1
agentRelease
OBJECT-TYPE
Release of the Agent.
1.3.6.1.4.1.9839.1.1Integer32read-onlycurrent
agentCode
OBJECT-TYPE
Code of the Agent. 2=pCOWeb.
1.3.6.1.4.1.9839.1.2Integer32read-onlycurrent
instruments
OBJECT-IDENTITY
1.3.6.1.4.1.9839.2
pCOWebInfo
OBJECT-IDENTITY
1.3.6.1.4.1.9839.2.0
pCOStatusgroup
OBJECT-IDENTITY
1.3.6.1.4.1.9839.2.0.10
pCOId1_Status
OBJECT-TYPE
Status of pCOId1. 0=Offline, 1=Init, 2=Online
1.3.6.1.4.1.9839.2.0.10.1Integer32read-onlycurrent
pCOErrorsNumbergroup
OBJECT-IDENTITY
1.3.6.1.4.1.9839.2.0.11
pCOId1_ErrorsNumber
OBJECT-TYPE
Number of Communication Errors from pCOId1 to pCOWeb.
1.3.6.1.4.1.9839.2.0.11.1Integer32read-onlycurrent
digitalObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9839.2.1.1
dehum_on
OBJECT-TYPE
Dehumidify mode is running
1.3.6.1.4.1.9839.2.1.1.1Integer32 (0..1)read-onlycurrent
hum_on
OBJECT-TYPE
Humidifier is running
1.3.6.1.4.1.9839.2.1.1.2Integer32 (0..1)read-onlycurrent
engy_on
OBJECT-TYPE
Energy saver is running
1.3.6.1.4.1.9839.2.1.1.3Integer32 (0..1)read-onlycurrent
cool_inhibit
OBJECT-TYPE
Cooling inhibit from Zone Master
1.3.6.1.4.1.9839.2.1.1.4Integer32 (0..1)read-onlycurrent
heat_held
OBJECT-TYPE
Heat inhibited due to alarm condition
1.3.6.1.4.1.9839.2.1.1.5Integer32 (0..1)read-onlycurrent
humidifier_inhibit
OBJECT-TYPE
Humidifier stopped due to alarm
1.3.6.1.4.1.9839.2.1.1.6Integer32 (0..1)read-onlycurrent
dehum_inhibit
OBJECT-TYPE
Dehum is inhibited
1.3.6.1.4.1.9839.2.1.1.7Integer32 (0..1)read-onlycurrent
rht_during_dehum
OBJECT-TYPE
reheat during dehum
1.3.6.1.4.1.9839.2.1.1.8Integer32 (0..1)read-onlycurrent
floor_wtr_alm
OBJECT-TYPE
Water under floor alarm
1.3.6.1.4.1.9839.2.1.1.9Integer32 (0..1)read-onlycurrent
air_flow_alm
OBJECT-TYPE
No air flow alarm
1.3.6.1.4.1.9839.2.1.1.10Integer32 (0..1)read-onlycurrent
filter_alm
OBJECT-TYPE
Dirty filter from digital input
1.3.6.1.4.1.9839.2.1.1.11Integer32 (0..1)read-onlycurrent
humidifier_alm
OBJECT-TYPE
Alarm from humidifier digital input
1.3.6.1.4.1.9839.2.1.1.12Integer32 (0..1)read-onlycurrent
firestat_alm
OBJECT-TYPE
Temperature of return air above firestat alarm set point
1.3.6.1.4.1.9839.2.1.1.13Integer32 (0..1)read-onlycurrent
shortcycle_alm
OBJECT-TYPE
One or more comps has short cycled
1.3.6.1.4.1.9839.2.1.1.14Integer32 (0..1)read-onlycurrent
humidity_fail
OBJECT-TYPE
Sensor is out of range
1.3.6.1.4.1.9839.2.1.1.15Integer32 (0..1)read-onlycurrent
ret_air_fail
OBJECT-TYPE
Sensor is out of range
1.3.6.1.4.1.9839.2.1.1.16Integer32 (0..1)read-onlycurrent
maint_alm
OBJECT-TYPE
Maintenance Schedule Due alarm
1.3.6.1.4.1.9839.2.1.1.17Integer32 (0..1)read-onlycurrent
c1_hp_alm
OBJECT-TYPE
High pressure alarm
1.3.6.1.4.1.9839.2.1.1.18Integer32 (0..1)read-onlycurrent
c1_lp_alm
OBJECT-TYPE
Low pressure alarm
1.3.6.1.4.1.9839.2.1.1.19Integer32 (0..1)read-onlycurrent
c2_hp_alm
OBJECT-TYPE
High pressure alarm
1.3.6.1.4.1.9839.2.1.1.20Integer32 (0..1)read-onlycurrent
c2_lp_alm
OBJECT-TYPE
Low pressure alarm
1.3.6.1.4.1.9839.2.1.1.21Integer32 (0..1)read-onlycurrent
smoke_alm
OBJECT-TYPE
Smoke detected from digital input
1.3.6.1.4.1.9839.2.1.1.22Integer32 (0..1)read-onlycurrent
wtr_flow_alm
OBJECT-TYPE
No water flow alarm
1.3.6.1.4.1.9839.2.1.1.23Integer32 (0..1)read-onlycurrent
disch_air_fail
OBJECT-TYPE
Sensor is out of range
1.3.6.1.4.1.9839.2.1.1.24Integer32 (0..1)read-onlycurrent
ra_tmp_hi_alm
OBJECT-TYPE
Temperature of return air above alarm set point
1.3.6.1.4.1.9839.2.1.1.25Integer32 (0..1)read-onlycurrent
ra_tmp_lo_alm
OBJECT-TYPE
Temperature of return air below alarm set point
1.3.6.1.4.1.9839.2.1.1.26Integer32 (0..1)read-onlycurrent
hum_hi_alm
OBJECT-TYPE
Humidity above alarm set point
1.3.6.1.4.1.9839.2.1.1.27Integer32 (0..1)read-onlycurrent
hum_lo_alm
OBJECT-TYPE
Humidity below alarm set point
1.3.6.1.4.1.9839.2.1.1.28Integer32 (0..1)read-onlycurrent
fan_overload
OBJECT-TYPE
Fan overload
1.3.6.1.4.1.9839.2.1.1.29Integer32 (0..1)read-onlycurrent
stdby_pump_on
OBJECT-TYPE
Standby pump on: Check primary pump -Optional alarm. Pump failure input signal required
1.3.6.1.4.1.9839.2.1.1.30Integer32 (0..1)read-onlycurrent
cust_msg_sw1
OBJECT-TYPE
Custom alarm #1 -Optional alarm. External alarm input required. Factory programmed custom message required
1.3.6.1.4.1.9839.2.1.1.31Integer32 (0..1)read-onlycurrent
cust_msg_sw2
OBJECT-TYPE
Custom alarm #2 -Optional alarm. External alarm input required. Factory programmed custom message required
1.3.6.1.4.1.9839.2.1.1.32Integer32 (0..1)read-onlycurrent
cust_msg_sw3
OBJECT-TYPE
Custom alarm #3 -Optional alarm. External alarm input required. Factory programmed custom message required
1.3.6.1.4.1.9839.2.1.1.33Integer32 (0..1)read-onlycurrent
cust_msg_sw4
OBJECT-TYPE
Custom alarm #4 -Optional alarm. External alarm input required. Factory programmed custom message required
1.3.6.1.4.1.9839.2.1.1.34Integer32 (0..1)read-onlycurrent
humsw_inhibit
OBJECT-TYPE
Humidifier stopped due to custom alarm switch
1.3.6.1.4.1.9839.2.1.1.35Integer32 (0..1)read-onlycurrent
heat_inhibit
OBJECT-TYPE
Heat inhibited due to custom switch alarm condition
1.3.6.1.4.1.9839.2.1.1.36Integer32 (0..1)read-onlycurrent
rht_hum_inhibit
OBJECT-TYPE
Reheat and humidification inhibited from operation
1.3.6.1.4.1.9839.2.1.1.37Integer32 (0..1)read-onlycurrent
disch_tmp_lo_alm
OBJECT-TYPE
Temperature of discharge air below alarm set point
1.3.6.1.4.1.9839.2.1.1.38Integer32 (0..1)read-onlycurrent
override_alm
OBJECT-TYPE
Manual override: Check bypass switches - Standard alarm. Manual override switch is on
1.3.6.1.4.1.9839.2.1.1.39Integer32 (0..1)read-onlycurrent
condensation_alm
OBJECT-TYPE
High condensation from digital input
1.3.6.1.4.1.9839.2.1.1.40Integer32 (0..1)read-onlycurrent
unit_in_standby
OBJECT-TYPE
Unit in standby, all functions held off - Optional alarm. Control input signal required Factory setting required
1.3.6.1.4.1.9839.2.1.1.41Integer32 (0..1)read-onlycurrent
cw_sns_fail
OBJECT-TYPE
Sensor is out of range
1.3.6.1.4.1.9839.2.1.1.42Integer32 (0..1)read-onlycurrent
humsw_chk_cyl
OBJECT-TYPE
Humidifier stopped due to custom alarm switch
1.3.6.1.4.1.9839.2.1.1.43Integer32 (0..1)read-onlycurrent
bms_cooling_inhibit
OBJECT-TYPE
Cooling operation inhibited by BMS
1.3.6.1.4.1.9839.2.1.1.44Integer32 (0..1)read-writecurrent
bms_heat_inhibit
OBJECT-TYPE
Heat inhibited due to bms
1.3.6.1.4.1.9839.2.1.1.45Integer32 (0..1)read-writecurrent
bms_humidifier_inhibit
OBJECT-TYPE
Humidifier operation inhibited by BMS
1.3.6.1.4.1.9839.2.1.1.46Integer32 (0..1)read-writecurrent
bms_dehum_inhibit
OBJECT-TYPE
Dehumidify mode inhibited by bms
1.3.6.1.4.1.9839.2.1.1.47Integer32 (0..1)read-writecurrent
fan_inhibit_bms
OBJECT-TYPE
Inhibit fan by bms
1.3.6.1.4.1.9839.2.1.1.48Integer32 (0..1)read-writecurrent
hum_expect
OBJECT-TYPE
Reduces control humidity cycling
1.3.6.1.4.1.9839.2.1.1.49Integer32 (0..1)read-onlycurrent
usashr_f_c
OBJECT-TYPE
Temperature Mode 0=_C 1=_F
1.3.6.1.4.1.9839.2.1.1.50Integer32 (0..1)read-writecurrent
lead_comp
OBJECT-TYPE
Lead compressor select 0= C1, 1= C2
1.3.6.1.4.1.9839.2.1.1.52Integer32 (0..1)read-onlycurrent
wtrvlv_dir
OBJECT-TYPE
Water valve direct or reverse acting
1.3.6.1.4.1.9839.2.1.1.53Integer32 (0..1)read-onlycurrent
ups_on_alm
OBJECT-TYPE
Alarm: UPS power on: Check main power -Optional alarm. External alarm input required
1.3.6.1.4.1.9839.2.1.1.54Integer32 (0..1)read-onlycurrent
pwrup_alm
OBJECT-TYPE
Loss of power requires manual reset of alarm
1.3.6.1.4.1.9839.2.1.1.55Integer32 (0..1)read-onlycurrent
seetag_cust_alm1
OBJECT-TYPE
Local alarm #1: See tag inside door =Optional alarm. External alarm input required
1.3.6.1.4.1.9839.2.1.1.56Integer32 (0..1)read-onlycurrent
seetag_cust_alm2
OBJECT-TYPE
Local alarm #2: See tag inside door =Optional alarm. External alarm input required
1.3.6.1.4.1.9839.2.1.1.57Integer32 (0..1)read-onlycurrent
seetag_cust_alm3
OBJECT-TYPE
Local alarm #3: See tag inside door =Optional alarm. External alarm input required
1.3.6.1.4.1.9839.2.1.1.58Integer32 (0..1)read-onlycurrent
seetag_cust_alm4
OBJECT-TYPE
Local alarm #4: See tag inside door =Optional alarm. External alarm input required
1.3.6.1.4.1.9839.2.1.1.59Integer32 (0..1)read-onlycurrent
shortcycle_alm_en
OBJECT-TYPE
Enable short cycle alarm of the compressors
1.3.6.1.4.1.9839.2.1.1.60Integer32 (0..1)read-onlycurrent
superv_off
OBJECT-TYPE
Supervisor (BMS) On-Off. Show the state OFFbyBMS in main mask (1: Off; 0: On
1.3.6.1.4.1.9839.2.1.1.61Integer32 (0..1)read-onlycurrent
BMS_heartbeat
OBJECT-TYPE
Bms heartbeat - pCO looks for update every 10 minutes
1.3.6.1.4.1.9839.2.1.1.62Integer32 (0..1)read-onlycurrent
analogObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9839.2.1.2
ret_air_tmp
OBJECT-TYPE
Temperature of return air
1.3.6.1.4.1.9839.2.1.2.1Integer32 (-32768..32767)read-onlycurrent
minmax_24hr_retair_maximum
OBJECT-TYPE
Maximum Return air temp in last 24hrs
1.3.6.1.4.1.9839.2.1.2.2Integer32 (-32768..32767)read-onlycurrent
minmax_24hr_retair_minumum
OBJECT-TYPE
Minimum Return air temp in last 24hrs
1.3.6.1.4.1.9839.2.1.2.3Integer32 (-32768..32767)read-onlycurrent
temp_setpoint
OBJECT-TYPE
Temperature setpoint
1.3.6.1.4.1.9839.2.1.2.4Integer32 (-9999..9999)read-writecurrent
temp_deadband
OBJECT-TYPE
Amount from setpoint before a comp is staged on
1.3.6.1.4.1.9839.2.1.2.5Integer32 (0..99)read-writecurrent
humidity_ain_offs
OBJECT-TYPE
Humidity Sensor Calibration
1.3.6.1.4.1.9839.2.1.2.6Integer32 (-32768..32767)read-onlycurrent
return_ain_offs
OBJECT-TYPE
Return Temperature Sensor Calibration
1.3.6.1.4.1.9839.2.1.2.7Integer32 (-32768..32767)read-onlycurrent
cw_tmp
OBJECT-TYPE
Temperature of chilled water
1.3.6.1.4.1.9839.2.1.2.8Integer32 (-32768..32767)read-onlycurrent
disch_air_tmp
OBJECT-TYPE
Temperature of discharge air
1.3.6.1.4.1.9839.2.1.2.9Integer32 (-32768..32767)read-onlycurrent
discharge_ain_offs
OBJECT-TYPE
Discharge Temperature Sensor Calibration - Optional discharge air temperature sensor required (B9)
1.3.6.1.4.1.9839.2.1.2.10Integer32 (-32768..32767)read-onlycurrent
cw_ain_offs
OBJECT-TYPE
Chilled Water Temperature Sensor Calibration - Optional chilled water temperature sensor required (B10)
1.3.6.1.4.1.9839.2.1.2.11Integer32 (-32768..32767)read-onlycurrent
engsaver_setpoint
OBJECT-TYPE
Temperature setpoint where chilled water will is requested
1.3.6.1.4.1.9839.2.1.2.12Integer32 (-9999..9999)read-writecurrent
opt1_analog
OBJECT-TYPE
Value of the analog input
1.3.6.1.4.1.9839.2.1.2.13Integer32 (-32768..32767)read-onlycurrent
opt2_analog
OBJECT-TYPE
Value of the analog input
1.3.6.1.4.1.9839.2.1.2.14Integer32 (-32768..32767)read-onlycurrent
opt3_analog
OBJECT-TYPE
Value of the analog input
1.3.6.1.4.1.9839.2.1.2.15Integer32 (-32768..32767)read-onlycurrent
opt4_analog
OBJECT-TYPE
Value of the analog input
1.3.6.1.4.1.9839.2.1.2.16Integer32 (-32768..32767)read-onlycurrent
opt_sns_1_y1
OBJECT-TYPE
Analog Sensor 1 Minimum Value
1.3.6.1.4.1.9839.2.1.2.17Integer32 (-32768..32767)read-onlycurrent
opt_sns_1_y2
OBJECT-TYPE
Analog Sensor 1 Maximum Value
1.3.6.1.4.1.9839.2.1.2.18Integer32 (-32768..32767)read-onlycurrent
opt_sns_1_ain_offs
OBJECT-TYPE
Analog Sensor 1 Calibration
1.3.6.1.4.1.9839.2.1.2.19Integer32 (-32768..32767)read-onlycurrent
opt_sns_2_y1
OBJECT-TYPE
Analog Sensor 2 Minimum Value
1.3.6.1.4.1.9839.2.1.2.20Integer32 (-32768..32767)read-onlycurrent
opt_sns_2_y2
OBJECT-TYPE
Analog Sensor 2 Maximum Value
1.3.6.1.4.1.9839.2.1.2.21Integer32 (-32768..32767)read-onlycurrent
opt_sns_2_ain_offs
OBJECT-TYPE
Analog Sensor 2 Calibration
1.3.6.1.4.1.9839.2.1.2.22Integer32 (-32768..32767)read-onlycurrent
opt_sns_3_y1
OBJECT-TYPE
Analog Sensor 3 Minimum Value
1.3.6.1.4.1.9839.2.1.2.23Integer32 (-32768..32767)read-onlycurrent
opt_sns_3_y2
OBJECT-TYPE
Analog Sensor 3 Maximum Value
1.3.6.1.4.1.9839.2.1.2.24Integer32 (-32768..32767)read-onlycurrent
opt_sns_3_ain_offs
OBJECT-TYPE
Analog Sensor 3 Calibration
1.3.6.1.4.1.9839.2.1.2.25Integer32 (-32768..32767)read-onlycurrent
opt_sns_4_y1
OBJECT-TYPE
Analog Sensor 4 Minimum Value
1.3.6.1.4.1.9839.2.1.2.26Integer32 (-32768..32767)read-onlycurrent
opt_sns_4_y2
OBJECT-TYPE
Analog Sensor 4 Maximum Value
1.3.6.1.4.1.9839.2.1.2.27Integer32 (-32768..32767)read-onlycurrent
opt_sns_4_ain_offs
OBJECT-TYPE
Analog Sensor 4 Calibration
1.3.6.1.4.1.9839.2.1.2.28Integer32 (-32768..32767)read-onlycurrent
integerObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9839.2.1.3
disch_air_lo_sp
OBJECT-TYPE
Lower Limit alarm of discharge air temp
1.3.6.1.4.1.9839.2.1.3.1Integer32 (-32767..32767)read-writecurrent
humidity_dis
OBJECT-TYPE
Relative humidity displayed as xx%
1.3.6.1.4.1.9839.2.1.3.2Integer32 (-999..999)read-onlycurrent
stages_on
OBJECT-TYPE
Cooling Stages On, DX only
1.3.6.1.4.1.9839.2.1.3.3Integer32 (-32767..32767)read-onlycurrent
heaters_on
OBJECT-TYPE
Number of heat stages running
1.3.6.1.4.1.9839.2.1.3.4Integer32 (-32768..32767)read-onlycurrent
minmax_24hr_hum_maximum
OBJECT-TYPE
Maximum humidity in last 24hrs
1.3.6.1.4.1.9839.2.1.3.5Integer32 (-32768..32767)read-onlycurrent
minmax_24hr_hum_minumum
OBJECT-TYPE
Minimum humidity in last 24hrs
1.3.6.1.4.1.9839.2.1.3.6Integer32 (-32768..32767)read-onlycurrent
comp_duty
OBJECT-TYPE
Cooling Utilization Over Last Hour -Percentage of cooling is used in the last hour of operation; this point applies to DX unit.
1.3.6.1.4.1.9839.2.1.3.7Integer32 (0..999)read-onlycurrent
heat_duty
OBJECT-TYPE
Heating Utilization Over Last Hour -Percentage of heating is used in the last hour of operation
1.3.6.1.4.1.9839.2.1.3.8Integer32 (0..999)read-onlycurrent
hum_duty
OBJECT-TYPE
Humidifier Utilization Over Last Hour -Percentage of humidifier is used in the last hour of operation
1.3.6.1.4.1.9839.2.1.3.9Integer32 (0..999)read-onlycurrent
c1_hours_h
OBJECT-TYPE
Compressor 1 Runtime -This point applies to DX unit with one compressor -high
1.3.6.1.4.1.9839.2.1.3.10Integer32 (-32768..32767)read-onlycurrent
c1_hours_l
OBJECT-TYPE
Compressor 1 Runtime -This point applies to DX unit with one compressor -low
1.3.6.1.4.1.9839.2.1.3.11Integer32 (-32768..32767)read-onlycurrent
c2_hours_h
OBJECT-TYPE
Compressor 2 Runtime -This point applies to DX unit with dual compressor - high
1.3.6.1.4.1.9839.2.1.3.12Integer32 (-32768..32767)read-onlycurrent
c2_hours_l
OBJECT-TYPE
Compressor 2 Runtime -This point applies to DX unit with dual compressor - low
1.3.6.1.4.1.9839.2.1.3.13Integer32 (-32768..32767)read-onlycurrent
ht1_hours_h
OBJECT-TYPE
Heater 1 Runtime - high
1.3.6.1.4.1.9839.2.1.3.14Integer32 (-32768..32767)read-onlycurrent
ht1_hours_l
OBJECT-TYPE
Heater 1 Runtime - low
1.3.6.1.4.1.9839.2.1.3.15Integer32 (-32768..32767)read-onlycurrent
current_second
OBJECT-TYPE
Current second
1.3.6.1.4.1.9839.2.1.3.16Integer32 (0..59)read-onlycurrent
current_minute
OBJECT-TYPE
Current minute
1.3.6.1.4.1.9839.2.1.3.17Integer32 (0..59)read-onlycurrent
current_hour
OBJECT-TYPE
Current hour
1.3.6.1.4.1.9839.2.1.3.18Integer32 (0..23)read-onlycurrent
current_day
OBJECT-TYPE
Current day
1.3.6.1.4.1.9839.2.1.3.19Integer32 (1..31)read-onlycurrent
current_month
OBJECT-TYPE
Current month
1.3.6.1.4.1.9839.2.1.3.20Integer32 (1..12)read-onlycurrent
current_year
OBJECT-TYPE
Current year
1.3.6.1.4.1.9839.2.1.3.21Integer32 (0..99)read-onlycurrent
firestat_sp
OBJECT-TYPE
Alarm settting of return air temp to determine there is a fire
1.3.6.1.4.1.9839.2.1.3.22Integer32 (0..999)read-writecurrent
hum_hi_sp
OBJECT-TYPE
Humidity upper limit alarm
1.3.6.1.4.1.9839.2.1.3.23Integer32 (0..99)read-writecurrent
ret_air_hi_sp
OBJECT-TYPE
Upper limit alarm of return air temp
1.3.6.1.4.1.9839.2.1.3.24Integer32 (-32768..32767)read-writecurrent
hum_lo_sp
OBJECT-TYPE
Humidity lower limit alarm
1.3.6.1.4.1.9839.2.1.3.25Integer32 (0..99)read-writecurrent
ret_air_lo_sp
OBJECT-TYPE
Lower limit alarm of return air temp
1.3.6.1.4.1.9839.2.1.3.26Integer32 (-32768..32767)read-writecurrent
hum_deadband
OBJECT-TYPE
amount hum must change from setpoint before acting
1.3.6.1.4.1.9839.2.1.3.27Integer32 (0..999)read-writecurrent
hum_setpoint
OBJECT-TYPE
humidity setpoint
1.3.6.1.4.1.9839.2.1.3.28Integer32 (0..999)read-writecurrent
start_dly
OBJECT-TYPE
Time before the system starts up
1.3.6.1.4.1.9839.2.1.3.29Integer32 (1..600)read-writecurrent
alm1_del
OBJECT-TYPE
Optional Alarm 1 Delay
1.3.6.1.4.1.9839.2.1.3.30Integer32 (0..32000)read-onlycurrent
alm2_del
OBJECT-TYPE
Optional Alarm 2 Delay
1.3.6.1.4.1.9839.2.1.3.31Integer32 (0..32000)read-onlycurrent
alm3_del
OBJECT-TYPE
Optional Alarm 3 Delay
1.3.6.1.4.1.9839.2.1.3.32Integer32 (0..32000)read-onlycurrent
alarm1_txt
OBJECT-TYPE
Message on optional alarm screen, some also add function
1.3.6.1.4.1.9839.2.1.3.33Integer32 (0..16)read-onlycurrent
alarm2_txt
OBJECT-TYPE
Message on optional alarm screen, some also add function
1.3.6.1.4.1.9839.2.1.3.34Integer32 (0..16)read-onlycurrent
alarm3_txt
OBJECT-TYPE
Message on optional alarm screen, some also add function
1.3.6.1.4.1.9839.2.1.3.35Integer32 (0..16)read-onlycurrent
alarm4_txt
OBJECT-TYPE
Message on optional alarm screen, some also add function
1.3.6.1.4.1.9839.2.1.3.36Integer32 (0..16)read-onlycurrent
comp_sel
OBJECT-TYPE
Comps 0=none, 1=one, 2=one+UL, 3=two, 4=two+UL, 5=Four/two circuit
1.3.6.1.4.1.9839.2.1.3.37Integer32 (0..5)read-onlycurrent
dehum_mode
OBJECT-TYPE
0=none, 1= comp limited, 2=twocomp limited, 3= comp unlimited, 4=twocomp unlimited
1.3.6.1.4.1.9839.2.1.3.38Integer32 (0..4)read-onlycurrent
reheat_sel
OBJECT-TYPE
Number of heat stages
1.3.6.1.4.1.9839.2.1.3.39Integer32 (0..3)read-onlycurrent
hum_sel
OBJECT-TYPE
0=none, 1=comp mod, 2=comp non, 3= comf mod, 4= conf non mod
1.3.6.1.4.1.9839.2.1.3.40Integer32 (0..4)read-onlycurrent
alm_contact_msg
OBJECT-TYPE
Text displayed on all alarm screens
1.3.6.1.4.1.9839.2.1.3.41Integer32 (0..4)read-onlycurrent
powerup_sel
OBJECT-TYPE
0= start wo/alarm, 1= start w/alarm, 2= requires reset of alarm
1.3.6.1.4.1.9839.2.1.3.42Integer32 (0..2)read-onlycurrent
buzzer_select
OBJECT-TYPE
0=None, 1=short beeps, 2=long beep, 3=Constant
1.3.6.1.4.1.9839.2.1.3.43Integer32 (0..3)read-onlycurrent
cw_disp
OBJECT-TYPE
% of 10volts of analog output #1
1.3.6.1.4.1.9839.2.1.3.44Integer32 (0..999)read-onlycurrent
wtrvlv_duty
OBJECT-TYPE
Chilled Water Utilization Over Last Hour - This applies to Chilled water or Energy saver units.
1.3.6.1.4.1.9839.2.1.3.45Integer32 (0..999)read-onlycurrent
hum_hours_h
OBJECT-TYPE
Humidifier Runtime - high
1.3.6.1.4.1.9839.2.1.3.46Integer32 (-32768..32767)read-onlycurrent
hum_hours_l
OBJECT-TYPE
Humidifier Runtime - low
1.3.6.1.4.1.9839.2.1.3.47Integer32 (-32768..32767)read-onlycurrent
blower_hours_h
OBJECT-TYPE
Blower Runtime - high
1.3.6.1.4.1.9839.2.1.3.48Integer32 (-32768..32767)read-onlycurrent
blower_hours_l
OBJECT-TYPE
Blower Runtime - low
1.3.6.1.4.1.9839.2.1.3.49Integer32 (-32768..32767)read-onlycurrent
alm4_del
OBJECT-TYPE
Optional Alarm 4 Delay
1.3.6.1.4.1.9839.2.1.3.50Integer32 (0..32000)read-onlycurrent
assist_sel
OBJECT-TYPE
0= no comp assist, 1=one comp assist, 2= two comp assist, 3... 4...
1.3.6.1.4.1.9839.2.1.3.51Integer32 (0..5)read-onlycurrent
wtrvlv_sel
OBJECT-TYPE
Water valve type 0=none, 1=chill, 2=Engy, 3=Aux chill, 4=Disc Reg
1.3.6.1.4.1.9839.2.1.3.52Integer32 (0..4)read-onlycurrent
wtrvlv_volts_sel
OBJECT-TYPE
Water valve voltage 0= 0-10, 1=2-10, 2=7-10, 3=6-9, 4=4-7
1.3.6.1.4.1.9839.2.1.3.53Integer32 (0..4)read-onlycurrent
hum_volts
OBJECT-TYPE
% of 10volts of analog output #2
1.3.6.1.4.1.9839.2.1.3.54Integer32 (0..999)read-onlycurrent
dehum_hours_h
OBJECT-TYPE
Dehumidifier Runtime - High
1.3.6.1.4.1.9839.2.1.3.55Integer32 (-32768..32767)read-onlycurrent
dehum_hours_l
OBJECT-TYPE
Dehumidifier Runtime - Low
1.3.6.1.4.1.9839.2.1.3.56Integer32 (-32768..32767)read-onlycurrent
autoflush_dly
OBJECT-TYPE
Time between drain cycles 0=12hr, 1=24hr, 2=48hr, 3=96hr, 4=None
1.3.6.1.4.1.9839.2.1.3.58Integer32 (0..99)read-onlycurrent
y4_out
OBJECT-TYPE
Value sent to optional analog output#1
1.3.6.1.4.1.9839.2.1.3.59Integer32 (-32768..32767)read-onlycurrent
y5_out
OBJECT-TYPE
Value sent to optional analog output#2
1.3.6.1.4.1.9839.2.1.3.60Integer32 (-32768..32767)read-onlycurrent
air_flow
OBJECT-TYPE
Current Fan Airflow - Based on calculated Pressure Diff formula
1.3.6.1.4.1.9839.2.1.3.61Integer32 (-32768..32767)read-onlycurrent
opt_snsr1_name
OBJECT-TYPE
Name of the sensor
1.3.6.1.4.1.9839.2.1.3.62Integer32 (-32768..32767)read-onlycurrent
opt_sns_1_ain_type
OBJECT-TYPE
Analog Sensor 1 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170}
1.3.6.1.4.1.9839.2.1.3.63Integer32 (0..9)read-onlycurrent
opt_snsr2_name
OBJECT-TYPE
Name of the sensor
1.3.6.1.4.1.9839.2.1.3.64Integer32 (-32768..32767)read-onlycurrent
opt_sns_2_ain_type
OBJECT-TYPE
Analog Sensor 2 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170}
1.3.6.1.4.1.9839.2.1.3.65Integer32 (0..9)read-onlycurrent
opt_snsr3_name
OBJECT-TYPE
Name of the sensor
1.3.6.1.4.1.9839.2.1.3.66Integer32 (-32768..32767)read-onlycurrent
opt_sns_3_ain_type
OBJECT-TYPE
Analog Sensor 3 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170}
1.3.6.1.4.1.9839.2.1.3.67Integer32 (0..9)read-onlycurrent
opt_snsr4_name
OBJECT-TYPE
Name of the sensor
1.3.6.1.4.1.9839.2.1.3.68Integer32 (-32768..32767)read-onlycurrent
opt_sns_4_ain_type
OBJECT-TYPE
Analog Sensor 4 Type {0=NTC 1=PT1000 2=0-1VDC 3=0-10VDC 4=4-20mA 5=ON/OFF 6=0-5VDC 7=NTC HT 8=-50T90 9=10T170}
1.3.6.1.4.1.9839.2.1.3.69Integer32 (0..9)read-onlycurrent
cw_fan_speed_bms
OBJECT-TYPE
CW Fan speed (%) sent via BMS
1.3.6.1.4.1.9839.2.1.3.70Integer32 (0..100)read-writecurrent
dx_fan_speed_bms
OBJECT-TYPE
DX Fan speed (%) sent via BMS
1.3.6.1.4.1.9839.2.1.3.71Integer32 (0..100)read-writecurrent
fan_speed_max
OBJECT-TYPE
Maximum Fan speed (% of output) modulation.
1.3.6.1.4.1.9839.2.1.3.72Integer32 (70..100)read-writecurrent
fan_speed_min
OBJECT-TYPE
Minimum Fan speed (% of output) modulation from pressure.
1.3.6.1.4.1.9839.2.1.3.73Integer32 (40..100)read-writecurrent
fan_pr_sp
OBJECT-TYPE
Fan pressure setpoint (0.01 inches of water)
1.3.6.1.4.1.9839.2.1.3.74Integer32 (0..1001)read-writecurrent
fan_pr_band
OBJECT-TYPE
Fan pressure band (0.01 inches of water)
1.3.6.1.4.1.9839.2.1.3.75Integer32 (1..100)read-writecurrent
fan_af_max
OBJECT-TYPE
Maximum air flow limit of setpoint from BMS or valve modulation.
1.3.6.1.4.1.9839.2.1.3.76Integer32 (0..32000)read-writecurrent
fan_af_min
OBJECT-TYPE
Minimum air flow limit of setpoint from BMS or valve modulation.
1.3.6.1.4.1.9839.2.1.3.77Integer32 (0..32000)read-writecurrent
fan_kfactor
OBJECT-TYPE
Fan K Factor
1.3.6.1.4.1.9839.2.1.3.78Integer32 (100..500)read-writecurrent
num_fans
OBJECT-TYPE
Number of fans installed in this unit
1.3.6.1.4.1.9839.2.1.3.79Integer32 (1..3)read-writecurrent
ht2_hours_h
OBJECT-TYPE
Heater 2 Runtime - high
1.3.6.1.4.1.9839.2.1.3.81Integer32 (-32768..32767)read-onlycurrent
ht2_hours_l
OBJECT-TYPE
Heater 2 Runtime - low
1.3.6.1.4.1.9839.2.1.3.82Integer32 (-32768..32767)read-onlycurrent
ht3_hours_h
OBJECT-TYPE
Heater 3 Runtime - high
1.3.6.1.4.1.9839.2.1.3.83Integer32 (-32768..32767)read-onlycurrent
ht3_hours_l
OBJECT-TYPE
Heater 3 Runtime - low
1.3.6.1.4.1.9839.2.1.3.84Integer32 (-32768..32767)read-onlycurrent
engy_hours_h
OBJECT-TYPE
Energy Saver Runtime - This optional point applies to energy saver units only -high
1.3.6.1.4.1.9839.2.1.3.85Integer32 (-32768..32767)read-onlycurrent
engy_hours_l
OBJECT-TYPE
Energy Saver Runtime - This optional point applies to energy saver units only - low
1.3.6.1.4.1.9839.2.1.3.86Integer32 (-32768..32767)read-onlycurrent
cw_hours_h
OBJECT-TYPE
Chilled Water Runtime - This applies to chilled water units only - high
1.3.6.1.4.1.9839.2.1.3.87Integer32 (-32768..32767)read-onlycurrent
cw_hours_l
OBJECT-TYPE
Chilled Water Runtime - This applies to chilled water units only - low
1.3.6.1.4.1.9839.2.1.3.88Integer32 (-32768..32767)read-onlycurrent
c3_hours_h
OBJECT-TYPE
Compressor 3 Runtime - This applies when unit has four stages tandem compressors - high
1.3.6.1.4.1.9839.2.1.3.89Integer32 (-32768..32767)read-onlycurrent
c3_hours_l
OBJECT-TYPE
Compressor 3 Runtime - This applies when unit has four stages tandem compressors - low
1.3.6.1.4.1.9839.2.1.3.90Integer32 (-32768..32767)read-onlycurrent
c4_hours_l
OBJECT-TYPE
Compressor 4 Runtime - This applies when unit has four stages tandem compressors. - high
1.3.6.1.4.1.9839.2.1.3.91Integer32 (-32768..32767)read-onlycurrent
c4_hours_h
OBJECT-TYPE
Compressor 4 Runtime - This applies when unit has four stages tandem compressors. - low
1.3.6.1.4.1.9839.2.1.3.92Integer32 (-32768..32767)read-onlycurrent
cond_hours_h
OBJECT-TYPE
Condenser Runtime - high
1.3.6.1.4.1.9839.2.1.3.93Integer32 (-32768..32767)read-onlycurrent
cond_hours_l
OBJECT-TYPE
Condenser Runtime - low
1.3.6.1.4.1.9839.2.1.3.94Integer32 (-32768..32767)read-onlycurrent
dx_fan_speed
OBJECT-TYPE
Fan speed (% of output) when compressor cooling.
1.3.6.1.4.1.9839.2.1.3.95Integer32 (60..100)read-onlycurrent
cw_fan_speed
OBJECT-TYPE
Fan speed (% of output) when cold water cooling.
1.3.6.1.4.1.9839.2.1.3.96Integer32 (60..100)read-onlycurrent
fan_af_dx_sp
OBJECT-TYPE
Fan air flow setpoint for DX unit (cfm)
1.3.6.1.4.1.9839.2.1.3.97Integer32 (0..32000)read-onlycurrent
fan_af_cw_sp
OBJECT-TYPE
Fan air flow setpoint for CW unit (cfm)
1.3.6.1.4.1.9839.2.1.3.98Integer32 (0..32000)read-onlycurrent
zm_airflow_sp
OBJECT-TYPE
Zone Airflow Setpoint kcfm
1.3.6.1.4.1.9839.2.1.3.99Integer32 (-32768..32767)read-writecurrent