MIBs Depot

DES3200-10-L2MGMT-MIB

Registered at
1.3.6.1.4.1.171.11.113.1.1.2
Last updated
1909-12-16 00:00
Organization
D-Link, Inc.
Namespace
dlink
Source file
DES3200-10-L2MGMT-MIB
Digest
sha256:68b04269b228f92eaeddf47ab78ae977c5d122dcfb125f9bd6debe2841138f8b

Description

The Structure of Layer 2 Network Management Information for enterprise.

Contact

http://support.dlink.com

Imports

FromSymbols
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIInteger32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, RowStatus, TEXTUAL-CONVENTION, TruthValue
SWPRIMGMT-DES3200-MIBdes3200-10

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DES3200-10-L2MGMT-MIB
DLINK-ID-REC-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC
SWPRIMGMT-DES3200-MIB

Textual conventions

NameOIDSyntaxAccessStatus
MacAddress
type
PortList
type
VlanId
type

Objects

NameOIDSyntaxAccessStatus
swL2DevMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.1
swL2DevInfo
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.1.1
swL2DevInfoFrontPanelLedStatus
OBJECT-TYPE
This object is a set of system LED indicators. The first two octets are defined as the system LED. The first indicator is the power LED. The second indicator is the console LED. The other octets are defined as follow: Starting on the third octet indicates the logical port LED (following dot1dBasePort ordering). Every two bytes are presented to a port. The first byte is presented to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED: The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED: 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
1.3.6.1.4.1.171.11.113.1.1.2.1.1.5OCTET STRING (SIZE(0..127))read-onlycurrent
swL2DevCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.1.2
swL2DevCtrlSystemReboot
OBJECT-TYPE
This object indicates the agent system reboot state. The agent always returns other(1) when this object is read.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.1INTEGER {other(1), reboot(2), save-config-and-reboot(3), reboot-and-load-factory-default-config(4)}read-writecurrent
swL2DevCtrlSystemIP
OBJECT-TYPE
This object indicates system IP.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.2IpAddressread-writecurrent
swL2DevCtrlSubnetMask
OBJECT-TYPE
This object indicates system subnet mask.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.3IpAddressread-writecurrent
swL2DevCtrlDefaultGateway
OBJECT-TYPE
This object indicates system default gateway.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.4IpAddressread-writecurrent
swL2DevCtrlManagementVlanId
OBJECT-TYPE
This object controls the VLAN, including system IP. The VLAN should have been created.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.5VlanIdread-writecurrent
swL2DevCtrlIGMPSnooping
OBJECT-TYPE
This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled .
1.3.6.1.4.1.171.11.113.1.1.2.1.2.7INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2DevCtrlCleanAllStatisticCounter
OBJECT-TYPE
As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.12INTEGER {normal(1), active(2)}read-writecurrent
swL2DevCtrlSnmpEnableAuthenTraps
OBJECT-TYPE
Indicates whether the SNMP entity is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authenticationFailure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant across re-initializations of the network management system.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.13INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlRmonState
OBJECT-TYPE
This object can be enabled or disabled RMON.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.16INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2DevCtrlIpAutoConfig
OBJECT-TYPE
Indicates the status of automatically getting configuration from TFTP server on device
1.3.6.1.4.1.171.11.113.1.1.2.1.2.17INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2MACNotifyState
OBJECT-TYPE
This object can enabled or disabled MAC Notification.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.19INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2MACNotifyHistorySize
OBJECT-TYPE
This object indicates the history size of variation MAC in address table. The default value is 1 .
1.3.6.1.4.1.171.11.113.1.1.2.1.2.20INTEGER (1..500)read-writecurrent
swL2MACNotifyInterval
OBJECT-TYPE
This object indicates the time interval in second for trigger the MAC notify message.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.21INTEGER (1..2147483647)read-writecurrent
swL2DevCtrlLLDPState
OBJECT-TYPE
Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.22INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlLLDPForwardMessageState
OBJECT-TYPE
When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Units packet will be forwarded.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.23INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlAsymVlanState
OBJECT-TYPE
This object enables or disables the asymmetric VLAN feature of the device.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.24INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2IGMPSnoopingMulticastVlanState
OBJECT-TYPE
This indicates the global state of the igmp_snoop multicast_vlan.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.25INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlVLANTrunkState
OBJECT-TYPE
This indicates the global state of the VLAN trunking feature of the device.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.26INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevArpAgingTime
OBJECT-TYPE
The timeout period in minutes for aging out dynamically learned ARP information.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.27INTEGER (0..65535)read-writecurrent
swL2DevPasswordEncryptionState
OBJECT-TYPE
If the password encryption is enabled, the password will be in encrypted form.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.28INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlCFM
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.1.2.29
swL2DevCtrlCFMState
OBJECT-TYPE
This object indicates the CFM global state.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.29.1INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlCFMPortTable
OBJECT-TYPE
A table containing the CFM state of specified ports.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.29.2not-accessiblecurrent
swL2DevCtrlCFMPortEntry
OBJECT-TYPE
The entry of the CFM state on specified ports.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.29.2.1not-accessiblecurrent
swL2DevCtrlCFMPortIndex
OBJECT-TYPE
This object indicates the port number.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.29.2.1.1INTEGERnot-accessiblecurrent
swL2DevCtrlCFMPortState
OBJECT-TYPE
This object indicates the CFM state by port.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.29.2.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlWeb
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.1.2.30
swL2DevCtrlWebState
OBJECT-TYPE
This object controls Web status.
1.3.6.1.4.1.171.11.113.1.1.2.1.2.30.1INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2DevAlarm
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.1.3
swL2DevAlarmLinkChange
OBJECT-TYPE
This object determines whether or not to send a trap message when the link changes. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device does not send the trap if this object value is disabled or in another state.
1.3.6.1.4.1.171.11.113.1.1.2.1.3.3INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.2
swL2PortInfoTable
OBJECT-TYPE
A table that contains information about every port.
1.3.6.1.4.1.171.11.113.1.1.2.2.1not-accessiblecurrent
swL2PortInfoEntry
OBJECT-TYPE
A list of information for each port of the device.
1.3.6.1.4.1.171.11.113.1.1.2.2.1.1not-accessiblecurrent
swL2PortInfoPortIndex
OBJECT-TYPE
This object indicates the module's port number.(1..Max port number in the module)
1.3.6.1.4.1.171.11.113.1.1.2.2.1.1.1INTEGER (1..255)read-onlycurrent
swL2PortInfoMediumType
OBJECT-TYPE
This object indicates the port type: fiber or copper.
1.3.6.1.4.1.171.11.113.1.1.2.2.1.1.2INTEGER {copper(100), fiber(101)}read-onlycurrent
swL2PortInfoLinkStatus
OBJECT-TYPE
This object indicates the port link status.
1.3.6.1.4.1.171.11.113.1.1.2.2.1.1.4INTEGER {other(1), link-pass(2), link-fail(3)}read-onlycurrent
swL2PortInfoNwayStatus
OBJECT-TYPE
This object indicates the port speed and duplex mode.
1.3.6.1.4.1.171.11.113.1.1.2.2.1.1.5INTEGER {auto(1), half-10Mbps(2), full-10Mbps(3), half-100Mbps(4), full-100Mbps(5), full-1Gigabps(7)}read-onlycurrent
swL2PortInfoFlowCtrlOperStatus
OBJECT-TYPE
The current operational state of flow control. The none (1) state indicates that no flow control is performed. The flow control mechanism is different between full duplex mode and half duplex mode. For full duplex mode, the IEEE 802.3x (2) flow control function sends PAUSE frames and receives PAUSE frames. For half duplex mode, backpressure (3) is performed.
1.3.6.1.4.1.171.11.113.1.1.2.2.1.1.10INTEGER {none(1), ieee8023x(2), backPressure(3)}read-onlycurrent
swL2PortCtrlTable
OBJECT-TYPE
A table that contains control information about every port.
1.3.6.1.4.1.171.11.113.1.1.2.2.2not-accessiblecurrent
swL2PortCtrlEntry
OBJECT-TYPE
A list of control information for each port of the device.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1not-accessiblecurrent
swL2PortCtrlPortIndex
OBJECT-TYPE
This object indicates the module's port number.(1..Max port number in the module)
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.1INTEGER (1..255)read-onlycurrent
swL2PortCtrlPortMediumType
OBJECT-TYPE
This object indicates the port type: fiber or copper.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.2INTEGER {copper(100), fiber(101)}read-onlycurrent
swL2PortCtrlAdminState
OBJECT-TYPE
This object decides whether the port is enabled or disabled.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.3INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortCtrlNwayState
OBJECT-TYPE
Choose the port speed, duplex mode, and N-Way function mode.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.4INTEGER {nway-auto(1), nway-disabled-10Mbps-Half(2), nway-disabled-10Mbps-Full(3), nway-disabled-100Mbps-Half(4), nway-disabled-100Mbps-Full(5), nway-disabled-1Gigabps-Full(7), nway-disabled-1Gigabps-Full-Master(8), nway-disabled-1Gigabps-Full-Slave(9)}read-writecurrent
swL2PortCtrlFlowCtrlState
OBJECT-TYPE
Set the flow control function as enabled or disabled.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.5INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortCtrlDescription
OBJECT-TYPE
The object describes the ports in text.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.6DisplayString (SIZE(0..32))read-writecurrent
swL2PortCtrlAddressLearning
OBJECT-TYPE
This object decides whether the address learning is enabled or disabled.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.7INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortCtrlMACNotifyState
OBJECT-TYPE
This object sets each port's MAC notification state.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.8INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortCtrlMulticastfilter
OBJECT-TYPE
This object decides the multicast packet filtering mode on this port.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.9INTEGER {forward-unregistered-groups(2), filter-unregistered-groups(3)}read-writecurrent
swL2PortCtrlMDIXState
OBJECT-TYPE
This object configures the MDIX setting of the port. The value 'other' is for those entries in which MDIX is not applicable.
1.3.6.1.4.1.171.11.113.1.1.2.2.2.1.10INTEGER {auto(1), normal(2), cross(3), other(4)}read-writecurrent
swL2PortErrTable
OBJECT-TYPE
A table that contains information about the Err port.
1.3.6.1.4.1.171.11.113.1.1.2.2.3not-accessiblecurrent
swL2PortErrEntry
OBJECT-TYPE
A list of information for the err port of the device.
1.3.6.1.4.1.171.11.113.1.1.2.2.3.1not-accessiblecurrent
swL2PortErrPortIndex
OBJECT-TYPE
This object indicates the module's port number.(1..Max port number in the module)
1.3.6.1.4.1.171.11.113.1.1.2.2.3.1.1INTEGER (1..255)read-onlycurrent
swL2PortErrPortState
OBJECT-TYPE
This object decides whether the port state is enabled or disabled.
1.3.6.1.4.1.171.11.113.1.1.2.2.3.1.2INTEGER {disabled(1), enabled(2)}read-onlycurrent
swL2PortErrPortStatus
OBJECT-TYPE
This object decides whether the PortStatus is err-disabled.
1.3.6.1.4.1.171.11.113.1.1.2.2.3.1.3INTEGER {other(1), err-disabled(2)}read-onlycurrent
swL2PortErrPortReason
OBJECT-TYPE
This object decides whether the PortStatus STP is LBD or Storm control.
1.3.6.1.4.1.171.11.113.1.1.2.2.3.1.4INTEGER {none(0), stp-lbd(1), storm-control(2), storm-control-lbd(3), loopdetect(4)}read-onlycurrent
swL2PortErrDescription
OBJECT-TYPE
The object describes the ports in text.
1.3.6.1.4.1.171.11.113.1.1.2.2.3.1.5DisplayString (SIZE(0..32))read-onlycurrent
swL2PortCtrlJumboFrame
OBJECT-TYPE
This object configures the switch's jumbo frame settings.
1.3.6.1.4.1.171.11.113.1.1.2.2.4INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2PortCtrlJumboFrameMaxSize
OBJECT-TYPE
This object describes how many bytes the max jumbo frame is.
1.3.6.1.4.1.171.11.113.1.1.2.2.5INTEGERread-onlycurrent
swL2QOSMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.3
swL2QOSBandwidthControlTable
OBJECT-TYPE
.
1.3.6.1.4.1.171.11.113.1.1.2.3.1not-accessiblecurrent
swL2QOSBandwidthControlEntry
OBJECT-TYPE
A list of information contained in swL2QOSBandwidthControlTable.
1.3.6.1.4.1.171.11.113.1.1.2.3.1.1not-accessiblecurrent
swL2QOSBandwidthPortIndex
OBJECT-TYPE
Indicates the port.
1.3.6.1.4.1.171.11.113.1.1.2.3.1.1.1INTEGER (1..650)read-onlycurrent
swL2QOSBandwidthRxRate
OBJECT-TYPE
Indicates the RX Rate(Kbit/sec) of the specified port. A value of 1024000 means no limit.
1.3.6.1.4.1.171.11.113.1.1.2.3.1.1.2INTEGER (64..1024000)read-writecurrent
swL2QOSBandwidthTxRate
OBJECT-TYPE
Indicates the TX Rate(Kbit/sec) of the specified port. A value of 1024000 means no limit.
1.3.6.1.4.1.171.11.113.1.1.2.3.1.1.3INTEGER (64..1024000)read-writecurrent
swL2QOSBandwidthRadiusRxRate
OBJECT-TYPE
The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate.
1.3.6.1.4.1.171.11.113.1.1.2.3.1.1.4INTEGERread-onlycurrent
swL2QOSBandwidthRadiusTxRate
OBJECT-TYPE
The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate.
1.3.6.1.4.1.171.11.113.1.1.2.3.1.1.5INTEGERread-onlycurrent
swL2QOSSchedulingTable
OBJECT-TYPE
.
1.3.6.1.4.1.171.11.113.1.1.2.3.2not-accessiblecurrent
swL2QOSSchedulingEntry
OBJECT-TYPE
A list of information contained in the swL2QOSSchedulingTable.
1.3.6.1.4.1.171.11.113.1.1.2.3.2.1not-accessiblecurrent
swL2QOSSchedulingClassIndex
OBJECT-TYPE
Indicates the hardware queue number.
1.3.6.1.4.1.171.11.113.1.1.2.3.2.1.1INTEGER (0..3)read-onlycurrent
swL2QOSSchedulingMaxWeight
OBJECT-TYPE
Indicates the maximum number of packets the above specified hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets.
1.3.6.1.4.1.171.11.113.1.1.2.3.2.1.4INTEGER (1..55)read-writecurrent
swL2QOSSchedulingMechanism
OBJECT-TYPE
Indicates the mechanism of QOS scheduling.
1.3.6.1.4.1.171.11.113.1.1.2.3.2.1.5INTEGER {strict(1), roundrobin(2), weightfair(3)}read-onlycurrent
swL2QOS8021pUserPriorityTable
OBJECT-TYPE
.
1.3.6.1.4.1.171.11.113.1.1.2.3.3not-accessiblecurrent
swL2QOS8021pUserPriorityEntry
OBJECT-TYPE
A list of information contained in the swL2QOS8021pUserPriorityTable.
1.3.6.1.4.1.171.11.113.1.1.2.3.3.1not-accessiblecurrent
swL2QOS8021pUserPriorityIndex
OBJECT-TYPE
The 802.1p user priority.
1.3.6.1.4.1.171.11.113.1.1.2.3.3.1.1INTEGER (0..7)read-onlycurrent
swL2QOS8021pUserPriorityClass
OBJECT-TYPE
The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
1.3.6.1.4.1.171.11.113.1.1.2.3.3.1.2INTEGER (0..3)read-writecurrent
swL2QOS8021pDefaultPriorityTable
OBJECT-TYPE
.
1.3.6.1.4.1.171.11.113.1.1.2.3.4not-accessiblecurrent
swL2QOS8021pDefaultPriorityEntry
OBJECT-TYPE
A list of information contained in the swL2QOS8021pDefaultPriorityTable.
1.3.6.1.4.1.171.11.113.1.1.2.3.4.1not-accessiblecurrent
swL2QOS8021pDefaultPriorityIndex
OBJECT-TYPE
Indicates the port number.
1.3.6.1.4.1.171.11.113.1.1.2.3.4.1.1INTEGER (1..650)read-onlycurrent
swL2QOS8021pDefaultPriority
OBJECT-TYPE
The priority value to assign to untagged packets received by the switch ports on the switch.
1.3.6.1.4.1.171.11.113.1.1.2.3.4.1.2INTEGER (0..7)read-writecurrent
swL2QOS8021pRadiusPriority
OBJECT-TYPE
Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
1.3.6.1.4.1.171.11.113.1.1.2.3.4.1.3INTEGERread-onlycurrent
swL2QOSSchedulingMechanismCtrl
OBJECT-TYPE
This object can control QOS scheduling Mechanism.
1.3.6.1.4.1.171.11.113.1.1.2.3.5INTEGER {strict(1), weightfair(2), none(3)}read-writecurrent
swL2TrunkMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.4
swPortTrunkMaxEntries
OBJECT-TYPE
The max entries of the swPortTrunkTable
1.3.6.1.4.1.171.11.113.1.1.2.4.1Integer32read-onlycurrent
swPortTrunkMaxPortMembers
OBJECT-TYPE
The max number of ports allowed in a trunk.
1.3.6.1.4.1.171.11.113.1.1.2.4.2Integer32read-onlycurrent
swPortTrunkTable
OBJECT-TYPE
This table specifies the port membership for each logical link.
1.3.6.1.4.1.171.11.113.1.1.2.4.3not-accessiblecurrent
swPortTrunkEntry
OBJECT-TYPE
A list of information that specifies which port group forms a single logical link.
1.3.6.1.4.1.171.11.113.1.1.2.4.3.1not-accessiblecurrent
swPortTrunkIndex
OBJECT-TYPE
The index of logical port trunk.
1.3.6.1.4.1.171.11.113.1.1.2.4.3.1.1Integer32 (1..3)read-onlycurrent
swPortTrunkMasterPort
OBJECT-TYPE
The object indicates the master port number of the port trunk entry. The first port of the trunk is implicitly configured to be the master logical port. When using a Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be the same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
1.3.6.1.4.1.171.11.113.1.1.2.4.3.1.2Integer32read-createcurrent
swPortTrunkPortList
OBJECT-TYPE
Indicate member ports of a logical trunk.
1.3.6.1.4.1.171.11.113.1.1.2.4.3.1.3PortListread-createcurrent
swPortTrunkType
OBJECT-TYPE
This object indicates the type of this entry.
1.3.6.1.4.1.171.11.113.1.1.2.4.3.1.4INTEGER {static(1), lacp(2)}read-createcurrent
swPortTrunkActivePort
OBJECT-TYPE
This object indicates the active ports of this entry.
1.3.6.1.4.1.171.11.113.1.1.2.4.3.1.5PortListread-onlycurrent
swPortTrunkState
OBJECT-TYPE
This object indicates the status of this entry. when the state is CreatAndGo (4),the type of trunk is static (1); when the state is CreatAndWait (5), the type of trunk is lacp(2).
1.3.6.1.4.1.171.11.113.1.1.2.4.3.1.6RowStatusread-createcurrent
swPortTrunkFloodingPort
OBJECT-TYPE
The flooding port of every trunk.
1.3.6.1.4.1.171.11.113.1.1.2.4.3.1.7Integer32read-onlycurrent
swL2TrunkAlgorithm
OBJECT-TYPE
This object configures part of the packet to be examined by the switch when selecting the egress port for transmitting load-sharing data.
1.3.6.1.4.1.171.11.113.1.1.2.4.4INTEGER {other(1), mac-source(2), mac-destination(3), mac-source-dest(4), ip-source(5), ip-destination(6), ip-source-dest(7)}read-writecurrent
swL2TrunkLACPPortTable
OBJECT-TYPE
This table specifies which port group a set of ports (up to 8) is formed into a single logical link.
1.3.6.1.4.1.171.11.113.1.1.2.4.5not-accessiblecurrent
swL2TrunkLACPPortEntry
OBJECT-TYPE
A list of information specifies which port group a set of ports (up to 8) is formed into a single logical link.
1.3.6.1.4.1.171.11.113.1.1.2.4.5.1not-accessiblecurrent
swL2TrunkLACPPortIndex
OBJECT-TYPE
The index of the logical port LACP.
1.3.6.1.4.1.171.11.113.1.1.2.4.5.1.1INTEGER (0..65535)read-onlycurrent
swL2TrunkLACPPortState
OBJECT-TYPE
The state of the logical port LACP.
1.3.6.1.4.1.171.11.113.1.1.2.4.5.1.2INTEGER {active(1), passive(2)}read-writecurrent
swL2TrunkVLANTable
OBJECT-TYPE
This table is used to manage the VLAN trunking feature of the device.
1.3.6.1.4.1.171.11.113.1.1.2.4.6not-accessiblecurrent
swL2TrunkVLANEntry
OBJECT-TYPE
This object is used to configure the VLAN trunking settings for each port.
1.3.6.1.4.1.171.11.113.1.1.2.4.6.1not-accessiblecurrent
swL2TrunkVLANPort
OBJECT-TYPE
This object indicates the port being configured.
1.3.6.1.4.1.171.11.113.1.1.2.4.6.1.1INTEGER (0..65535)read-onlycurrent
swL2TrunkVLANState
OBJECT-TYPE
The state of the logical port LACP.
1.3.6.1.4.1.171.11.113.1.1.2.4.6.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
swPortMirrorPackage
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.6
swPortMirrorRxPortList
OBJECT-TYPE
This object indicates the Rx port list of ports to be sniffed.
1.3.6.1.4.1.171.11.113.1.1.2.6.2PortListread-writecurrent
swPortMirrorTxPortList
OBJECT-TYPE
This object indicates the Tx port list of ports to be sniffed.
1.3.6.1.4.1.171.11.113.1.1.2.6.3PortListread-writecurrent
swPortMirrorTargetPort
OBJECT-TYPE
This object indicates the switch whose port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
1.3.6.1.4.1.171.11.113.1.1.2.6.4Integer32read-writecurrent
swPortMirrorState
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.11.113.1.1.2.6.5INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swIGMPPackage
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.7
swL2IGMPMaxSupportedVlans
OBJECT-TYPE
The maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).
1.3.6.1.4.1.171.11.113.1.1.2.7.1INTEGER (0..65535)read-onlycurrent
swL2IGMPMaxIpGroupNumPerVlan
OBJECT-TYPE
The maximum number of multicast IP groups per VLAN in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
1.3.6.1.4.1.171.11.113.1.1.2.7.2INTEGER (0..65535)read-onlycurrent
swL2IGMPCtrlTable
OBJECT-TYPE
The table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If the VLAN mode is disabled, there is only one entry in the table, with index 1. If VLAN is in Port-Based or 802.1q mode, the number of entries can be up to 12, with an index range from 1 to 12.
1.3.6.1.4.1.171.11.113.1.1.2.7.3not-accessiblecurrent
swL2IGMPCtrlEntry
OBJECT-TYPE
An entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP captures the switch (swL2DevCtrlIGMPSnooping) is enabled.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1not-accessiblecurrent
swL2IGMPCtrlVid
OBJECT-TYPE
This object indicates the IGMP control entry's VLAN ID. If VLAN is disabled, the VID is always 0 and cannot be changed by management users. If VLAN is in Port-Based mode, the VID is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the VID setting can vary from 1 to 4094 by management user, and the VID in each entry must be unique in the IGMP Control Table.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.1INTEGER (0..65535)read-onlycurrent
swL2IGMPQueryInterval
OBJECT-TYPE
The frequency at which IGMP Host-Query packets are transmitted on this switch.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.2INTEGER (1..65535)read-writecurrent
swL2IGMPMaxResponseTime
OBJECT-TYPE
The maximum query response time on this switch.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.3INTEGER (1..25)read-writecurrent
swL2IGMPRobustness
OBJECT-TYPE
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.4INTEGER (1..255)read-writecurrent
swL2IGMPLastMemberQueryInterval
OBJECT-TYPE
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.5INTEGER (1..25)read-writecurrent
swL2IGMPQueryState
OBJECT-TYPE
This object decides if the IGMP query is enabled or disabled.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.9INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2IGMPCurrentState
OBJECT-TYPE
This object indicates the current IGMP query state.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.10INTEGER {other(1), querier(2), non-querier(3)}read-onlycurrent
swL2IGMPCtrlState
OBJECT-TYPE
This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable (2) - IGMP function is disabled for this entry. enable (3) - IGMP function is enabled for this entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.11INTEGER {other(1), disable(2), enable(3)}read-writecurrent
swL2IGMPFastLeave
OBJECT-TYPE
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.12INTEGER {other(1), disable(2), enable(3)}read-writecurrent
swL2IGMPDynIPMultVlanAge
OBJECT-TYPE
This object is used to enable or disable aging on the dynamic IP multicast entry in this VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.7.3.1.14INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2IGMPQueryInfoTable
OBJECT-TYPE
The table contains the number of current IGMP query packets which are captured by this device, as well as the IGMP query packets sent by the device.
1.3.6.1.4.1.171.11.113.1.1.2.7.4not-accessiblecurrent
swL2IGMPQueryInfoEntry
OBJECT-TYPE
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
1.3.6.1.4.1.171.11.113.1.1.2.7.4.1not-accessiblecurrent
swL2IGMPInfoVid
OBJECT-TYPE
This object indicates the VID of the associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
1.3.6.1.4.1.171.11.113.1.1.2.7.4.1.1INTEGER (0..65535)read-onlycurrent
swL2IGMPInfoQueryCount
OBJECT-TYPE
This object indicates the number of query packets received since the IGMP function enabled, on a per-VLAN basis.
1.3.6.1.4.1.171.11.113.1.1.2.7.4.1.2INTEGER (0..65535)read-onlycurrent
swL2IGMPInfoTxQueryCount
OBJECT-TYPE
This object indicates the send count of IGMP query messages, on a per-VLAN basis. In case of the IGMP timer expiring, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
1.3.6.1.4.1.171.11.113.1.1.2.7.4.1.3INTEGER (0..65535)read-onlycurrent
swL2IGMPRouterPortTable
OBJECT-TYPE
The information of the router port table.
1.3.6.1.4.1.171.11.113.1.1.2.7.6not-accessiblecurrent
swL2IGMPRouterPortEntry
OBJECT-TYPE
The entry of the swL2IGMPRouterPortTable.
1.3.6.1.4.1.171.11.113.1.1.2.7.6.1not-accessiblecurrent
swL2IGMPRouterPortVlanid
OBJECT-TYPE
This object indicates the VLAN ID of the router port entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.6.1.1INTEGER (1..4094)read-onlycurrent
swL2IGMPRouterPortVlanName
OBJECT-TYPE
This object indicates the VLAN name of the router port entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.6.1.2SnmpAdminString (SIZE(0..32))read-onlycurrent
swL2IGMPRouterPortStaticPortList
OBJECT-TYPE
This object indicates the static portlist of the router port entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.6.1.3PortListread-writecurrent
swL2IGMPRouterPortDynamicPortList
OBJECT-TYPE
This object indicates the dynamic portlist of the router port entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.6.1.4PortListread-onlycurrent
swL2IGMPRouterPortForbiddenPortList
OBJECT-TYPE
This object indicates the forbidden portlist of the router port entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.6.1.5PortListread-writecurrent
swL2IGMPAccessAuthTable
OBJECT-TYPE
This table is used to manage the IGMP Access Authentication configurations of the device.
1.3.6.1.4.1.171.11.113.1.1.2.7.7not-accessiblecurrent
swL2IGMPAccessAuthEntry
OBJECT-TYPE
A list of manageable entities for IGMP Access Authentication. The configuration is done per port.
1.3.6.1.4.1.171.11.113.1.1.2.7.7.1not-accessiblecurrent
swL2IGMPAccessAuthPort
OBJECT-TYPE
The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.
1.3.6.1.4.1.171.11.113.1.1.2.7.7.1.1INTEGERread-onlycurrent
swL2IGMPAccessAuthState
OBJECT-TYPE
This object denotes the status of IGMP Access Authentication of the port.
1.3.6.1.4.1.171.11.113.1.1.2.7.7.1.2INTEGER {disabled(1), enabled(2)}read-writecurrent
swL2IGMPMulticastVlanTable
OBJECT-TYPE
Information about the IGMP snooping multicast VLAN table.
1.3.6.1.4.1.171.11.113.1.1.2.7.8not-accessiblecurrent
swL2IGMPMulticastVlanEntry
OBJECT-TYPE
The entry of swL2IGMPMulticastVlanTable.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1not-accessiblecurrent
swL2IGMPMulticastVlanid
OBJECT-TYPE
This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.1INTEGER (2..4094)read-onlycurrent
swL2IGMPMulticastVlanName
OBJECT-TYPE
This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.2DisplayString (SIZE(0..32))read-createcurrent
swL2IGMPMulticastVlanSourcePort
OBJECT-TYPE
This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.3PortListread-writecurrent
swL2IGMPMulticastVlanMemberPort
OBJECT-TYPE
This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The member ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.4PortListread-writecurrent
swL2IGMPMulticastVlanTagMemberPort
OBJECT-TYPE
This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.5PortListread-writecurrent
swL2IGMPMulticastVlanState
OBJECT-TYPE
This object can be used to enable or disable the IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.6INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2IGMPMulticastVlanReplaceSourceIp
OBJECT-TYPE
The replacement source IP of this multicast VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.7IpAddressread-writecurrent
swL2IGMPMulticastVlanRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.8RowStatusread-createcurrent
swL2IGMPMulticastVlanUntagSourcePort
OBJECT-TYPE
This object indicates the port list of the untag source ports of the IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.9PortListread-createcurrent
swL2IGMPMulticastVlanRemapPriority
OBJECT-TYPE
This is the priority value (0 to 7) to be associated with the data traffic to be forwarded on the multicast VLAN. When set to -1, the packet's original priority will be used.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.10INTEGER (-1 | 0..7)read-createcurrent
swL2IGMPMulticastVlanReplacePriority
OBJECT-TYPE
This specifies that a packet's priority will be changed by the switch based on the remap priority. This flag will only take effect when remap priority is set.
1.3.6.1.4.1.171.11.113.1.1.2.7.8.1.11INTEGER {enabled(1), disabled(2)}read-createcurrent
swL2IGMPMulticastVlanGroupTable
OBJECT-TYPE
The table containing the IGMP snooping multicast VLAN group information
1.3.6.1.4.1.171.11.113.1.1.2.7.9not-accessiblecurrent
swL2IGMPMulticastVlanGroupEntry
OBJECT-TYPE
Information about the current IGMP snooping multicast VLAN group.
1.3.6.1.4.1.171.11.113.1.1.2.7.9.1not-accessiblecurrent
swL2IGMPMulticastVlanGroupVid
OBJECT-TYPE
This object indicates the VID of the IGMP snooping multicast VLAN group.
1.3.6.1.4.1.171.11.113.1.1.2.7.9.1.1INTEGER (1..4094)read-onlycurrent
swL2IGMPMulticastVlanGroupFromIp
OBJECT-TYPE
Specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.7.9.1.2IpAddressread-onlycurrent
swL2IGMPMulticastVlanGroupToIp
OBJECT-TYPE
Specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.7.9.1.3IpAddressread-onlycurrent
swL2IGMPMulticastVlanGroupStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.9.1.4RowStatusread-createcurrent
swL2IGMPDynIpMultMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.7.12
swL2IGMPDynIPMultMaxEntry
OBJECT-TYPE
This object specifies the maximum number of entries which can be learned by dynamic IP multicast.
1.3.6.1.4.1.171.11.113.1.1.2.7.12.1INTEGERread-writecurrent
swL2IGMPSnoopingClearDynIpMult
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.7.12.2
swL2IGMPSnoopingClearDynIpMultVID
OBJECT-TYPE
This object indicates the VLAN identifier where the data driven entries will be removed from.
1.3.6.1.4.1.171.11.113.1.1.2.7.12.2.1VlanIdread-writecurrent
swL2IGMPSnoopingClearDynIpMultIP
OBJECT-TYPE
This object indicates the IP address of the IGMP snooping group from which the data driven entries will be removed.
1.3.6.1.4.1.171.11.113.1.1.2.7.12.2.2IpAddressread-writecurrent
swL2IGMPSnoopingClearDynIpMultAction
OBJECT-TYPE
Setting this object will clear the data driven entries. all - Remove all learned data driven groups. VLAN - Clear all data driven entries in the VLAN specified in swIGMPSnoopingClearDynIpMultVID. group - Clear the group with the address specified in swL2IGMPSnoopingClearDynIpMultIP in the VLAN specified in swIGMPSnoopingClearDynIpMultVID.
1.3.6.1.4.1.171.11.113.1.1.2.7.12.2.3INTEGER {all(1), vlan(2), group(3), other(4)}read-writecurrent
swIGMPSnoopingHostTable
OBJECT-TYPE
The table contains the IGMP hosts that have joined the groups.
1.3.6.1.4.1.171.11.113.1.1.2.7.13not-accessiblecurrent
swIGMPSnoopingHostEntry
OBJECT-TYPE
The entry contains the IGMP host that has joined the group.
1.3.6.1.4.1.171.11.113.1.1.2.7.13.1not-accessiblecurrent
swIGMPSnoopingHostVid
OBJECT-TYPE
This object indicates the VID of the individual IGMP snooping host table entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.13.1.1VlanIdread-onlycurrent
swIGMPSnoopingHostGroup
OBJECT-TYPE
This object indicates the group address of the individual IGMP snooping host table entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.13.1.2IpAddressread-onlycurrent
swIGMPSnoopingHostPort
OBJECT-TYPE
This object indicates the port number of the individual IGMP snooping host table entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.13.1.3INTEGERread-onlycurrent
swIGMPSnoopingHostIp
OBJECT-TYPE
This object indicates the host IP address of the individual IGMP snooping host table entry.
1.3.6.1.4.1.171.11.113.1.1.2.7.13.1.4IpAddressread-onlycurrent
swL2TrafficSegMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.12
swL2TrafficSegTable
OBJECT-TYPE
This table specifies the port just can forward traffic to the specific port list.
1.3.6.1.4.1.171.11.113.1.1.2.12.1not-accessiblecurrent
swL2TrafficSegEntry
OBJECT-TYPE
A list of information specifies the port with its traffic forward list.
1.3.6.1.4.1.171.11.113.1.1.2.12.1.1not-accessiblecurrent
swL2TrafficSegPort
OBJECT-TYPE
The port number of the logical port.
1.3.6.1.4.1.171.11.113.1.1.2.12.1.1.1INTEGER (0..65535)read-onlycurrent
swL2TrafficSegForwardPorts
OBJECT-TYPE
The port list that the specific port can forward traffic.
1.3.6.1.4.1.171.11.113.1.1.2.12.1.1.2PortListread-writecurrent
swL2PortSecurityMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.15
swL2PortSecurityControlTable
OBJECT-TYPE
The port security feature controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as a static entry. When the learned address number reaches N, any incoming packet without learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
1.3.6.1.4.1.171.11.113.1.1.2.15.1not-accessiblecurrent
swL2PortSecurityControlEntry
OBJECT-TYPE
A list of information contained in the swL2PortSecurityControlTable.
1.3.6.1.4.1.171.11.113.1.1.2.15.1.1not-accessiblecurrent
swL2PortSecurityPortIndex
OBJECT-TYPE
Indicates a secured port to lock address learning.
1.3.6.1.4.1.171.11.113.1.1.2.15.1.1.1INTEGER (1..255)read-onlycurrent
swL2PortSecurityMaxLernAddr
OBJECT-TYPE
Indicates the allowable number of addresses to be learned at this port.
1.3.6.1.4.1.171.11.113.1.1.2.15.1.1.2INTEGER (0..64)read-writecurrent
swL2PortSecurityMode
OBJECT-TYPE
Indicates the mode of locking address. In deleteOnTimeout (3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that can be learned has to be increased by one. In deleteOnReset (4) mode - never age out the locked addresses unless restarting the system to prevent port movement or intrusion.
1.3.6.1.4.1.171.11.113.1.1.2.15.1.1.3INTEGER {other(1), permanent(2), deleteOnTimeout(3), deleteOnReset(4)}read-writecurrent
swL2PortSecurityAdmState
OBJECT-TYPE
Indicates an administration state of locking address.
1.3.6.1.4.1.171.11.113.1.1.2.15.1.1.4INTEGER {other(1), enable(2), disable(3)}read-writecurrent
swL2PortSecurityEntryClearCtrl
OBJECT-TYPE
Used to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'.
1.3.6.1.4.1.171.11.113.1.1.2.15.1.1.5INTEGER {other(1), start(2)}read-writecurrent
swL2PortSecurityTrapLogState
OBJECT-TYPE
When enabled (2), whenever there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out and the relevant information will be logged in the system.
1.3.6.1.4.1.171.11.113.1.1.2.15.2INTEGER {other(1), enable(2), disable(3)}read-writecurrent
swL2PortSecurityDelCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.15.3
swL2PortSecurityDelVlanName
OBJECT-TYPE
Indicates the VLAN name.
1.3.6.1.4.1.171.11.113.1.1.2.15.3.1DisplayString (SIZE(0..32))read-writecurrent
swL2PortSecurityDelPort
OBJECT-TYPE
Indicates the port. 0 means the function dose not work now.
1.3.6.1.4.1.171.11.113.1.1.2.15.3.2INTEGER (0..768)read-writecurrent
swL2PortSecurityDelMacAddress
OBJECT-TYPE
Specifies the MAC address.
1.3.6.1.4.1.171.11.113.1.1.2.15.3.3MacAddressread-writecurrent
swL2PortSecurityDelActivity
OBJECT-TYPE
1.3.6.1.4.1.171.11.113.1.1.2.15.3.4INTEGER {none(1), start(2)}read-writecurrent
swL2CosMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.17
swL2CosPriorityCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.17.3
swL2CosPriorityTable
OBJECT-TYPE
Used to show and configure per port priority-based QoS features on the switch.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.1not-accessiblecurrent
swL2CosPriorityEntry
OBJECT-TYPE
A list of information contained in the swL2CosPriorityTable.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.1.1not-accessiblecurrent
swL2CosPriorityPort
OBJECT-TYPE
The port number of CoS Priority.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.1.1.1INTEGER (1..65535)read-onlycurrent
swL2CosPriorityEtherPRI
OBJECT-TYPE
Enable Ethernet frame based priority. When set ether8021p (2), enable 802.1p QoS; When set macBase (3), enable MAC-based QoS; When set disable (1), disable Ethernet frame based priority.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.1.1.3INTEGER {disable(1), ether8021p(2), macBase(3)}read-writecurrent
swL2CosPriorityIpPRI
OBJECT-TYPE
Enable IP priority QoS. When set tos (2), enable TOS based QoS; When set dscp (3), enable DSCP based QoS; When set disable (1), disable IP priority QoS.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.1.1.4INTEGER {disable(1), tos(2), dscp(3)}read-writecurrent
swL2CosPriorityNone
OBJECT-TYPE
When read, it always returns invalid (2); when write valid (1), it disables all priority in this table.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.1.1.5INTEGER {valid(1), invalid(2)}read-writecurrent
swL2CosTosPRITable
OBJECT-TYPE
Used to show TOS value to traffic class mapping and map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.4not-accessiblecurrent
swL2CosTosPRIEntry
OBJECT-TYPE
A list of information contained in the swL2CosTosPRITable.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.4.1not-accessiblecurrent
swL2CosTosPRIIndex
OBJECT-TYPE
Indicates the CoS Priority TosPRI.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.4.1.1INTEGER (0..7)read-onlycurrent
swL2CosTosPRIClass
OBJECT-TYPE
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.4.1.2INTEGER (0..3)read-writecurrent
swL2CosDscpPRITable
OBJECT-TYPE
Used to show DSCP value to traffic class mapping and map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.5not-accessiblecurrent
swL2CosDscpPRIEntry
OBJECT-TYPE
A list of information contained in the swL2CosDscpPRITable.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.5.1not-accessiblecurrent
swL2CosDscpPRIIndex
OBJECT-TYPE
Indicates the CoS Priority DscpPRI.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.5.1.1INTEGER (0..63)read-onlycurrent
swL2CosDscpPRIClass
OBJECT-TYPE
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
1.3.6.1.4.1.171.11.113.1.1.2.17.3.5.1.2INTEGER (0..3)read-writecurrent
swL2DhcpRelayMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.18
swL2DhcpRelayState
OBJECT-TYPE
This object indicates whether the DHCP relay function is enabled or disabled.
1.3.6.1.4.1.171.11.113.1.1.2.18.1INTEGER {other(1), disabled(2), enabled(3)}read-writeobsolete
swL2DhcpRelayHopCount
OBJECT-TYPE
This object indicates the maximum number of router hops that the DHCP packets can cross.
1.3.6.1.4.1.171.11.113.1.1.2.18.2INTEGER (1..16)read-writeobsolete
swL2DhcpRelayTimeThreshold
OBJECT-TYPE
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
1.3.6.1.4.1.171.11.113.1.1.2.18.3INTEGER (0..65535)read-writeobsolete
swL2DhcpRelayOption82State
OBJECT-TYPE
This object indicates DHCP relay agent information option 82 function is enabled or disabled.
1.3.6.1.4.1.171.11.113.1.1.2.18.4INTEGER {other(1), disabled(2), enabled(3)}read-writeobsolete
swL2DhcpRelayOption82Check
OBJECT-TYPE
This object indicates the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.
1.3.6.1.4.1.171.11.113.1.1.2.18.5INTEGER {other(1), disabled(2), enabled(3)}read-writeobsolete
swL2DhcpRelayOption82Policy
OBJECT-TYPE
This object indicates the reforwarding policy of DHCP relay agent information option 82. replace (1) - Replace the exiting option 82 field in messages. drop (2) - Discard messages with existing option 82 field. keep (3) - Retain the existing option 82 field in messages.
1.3.6.1.4.1.171.11.113.1.1.2.18.6INTEGER {replace(1), drop(2), keep(3)}read-writeobsolete
swL2DhcpRelayCtrlTable
OBJECT-TYPE
This table specifies the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.11.113.1.1.2.18.7not-accessibleobsolete
swL2DhcpRelayCtrlEntry
OBJECT-TYPE
A list of information specifies the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.11.113.1.1.2.18.7.1not-accessibleobsolete
swL2DhcpRelayCtrlInterfaceName
OBJECT-TYPE
The name of the IP interface.
1.3.6.1.4.1.171.11.113.1.1.2.18.7.1.1DisplayString (SIZE(1..12))read-onlyobsolete
swL2DhcpRelayCtrlServer
OBJECT-TYPE
The DHCP server IP address.
1.3.6.1.4.1.171.11.113.1.1.2.18.7.1.2IpAddressread-onlyobsolete
swL2DhcpRelayCtrlState
OBJECT-TYPE
This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid (2) - Writing this value to the object, and then the corresponding entry will be removed from the table. valid (3) - This entry resides in the table.
1.3.6.1.4.1.171.11.113.1.1.2.18.7.1.3INTEGER {other(1), invalid(2), valid(3)}read-writeobsolete
swL2MgmtMIBTraps
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.20
swL2MgmtMIBTrapPrefix
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.20.0
swl2PortSecurityBindings
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.20.1
swL2PortSecurityViolationMac
OBJECT-TYPE
This object indicates the MAC address that violates the port security configuration.
1.3.6.1.4.1.171.11.113.1.1.2.20.1.1MacAddressaccessible-for-notifycurrent
swl2NotificationBindings
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.20.2
swL2macNotifyInfo
OBJECT-TYPE
This object indicates the last time reboot information.
1.3.6.1.4.1.171.11.113.1.1.2.20.2.1OCTET STRING (SIZE(0..1024))read-onlycurrent
swL2VlanLoopDetectVID
OBJECT-TYPE
This object indicates the VID that detected a loopback.
1.3.6.1.4.1.171.11.113.1.1.2.20.2.2INTEGERaccessible-for-notifycurrent
swL2LoopDetectMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.21
swL2LoopDetectCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.21.1
swL2LoopDetectAdminState
OBJECT-TYPE
This object indicates the loopback detection status for the system.
1.3.6.1.4.1.171.11.113.1.1.2.21.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2LoopDetectInterval
OBJECT-TYPE
This object indicates the interval value, the range is from 1 to 32767 seconds.
1.3.6.1.4.1.171.11.113.1.1.2.21.1.2INTEGER (1..32767)read-writecurrent
swL2LoopDetectRecoverTime
OBJECT-TYPE
This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
1.3.6.1.4.1.171.11.113.1.1.2.21.1.3INTEGER (0..1000000)read-writecurrent
swL2LoopDetectMode
OBJECT-TYPE
This object indicates the loopback detection mode for the system.
1.3.6.1.4.1.171.11.113.1.1.2.21.1.4INTEGER {vlan-based(1), port-based(2)}read-writecurrent
swL2LoopDetectTrapMode
OBJECT-TYPE
This object indicates the loopback detection trap mode for the system.
1.3.6.1.4.1.171.11.113.1.1.2.21.1.5INTEGER {none(1), loop-detected(2), loop-cleared(3), both(4)}read-writecurrent
swL2LoopDetectPortMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.21.2
swL2LoopDetectPortTable
OBJECT-TYPE
The table specifies the loopback detection function specified by port.
1.3.6.1.4.1.171.11.113.1.1.2.21.2.1not-accessiblecurrent
swL2LoopDetectPortEntry
OBJECT-TYPE
The table specifies the loopback detection function specified by port.
1.3.6.1.4.1.171.11.113.1.1.2.21.2.1.1not-accessiblecurrent
swL2LoopDetectPortIndex
OBJECT-TYPE
This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
1.3.6.1.4.1.171.11.113.1.1.2.21.2.1.1.1INTEGER (1..65535)read-onlycurrent
swL2LoopDetectPortState
OBJECT-TYPE
This object indicates the loopback detection function state on the port.
1.3.6.1.4.1.171.11.113.1.1.2.21.2.1.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2LoopDetectPortLoopVLAN
OBJECT-TYPE
This object indicates the VLAN list that has detected a loopback.
1.3.6.1.4.1.171.11.113.1.1.2.21.2.1.1.3DisplayStringread-onlycurrent
swL2LoopDetectPortLoopStatus
OBJECT-TYPE
This object indicates the port status.
1.3.6.1.4.1.171.11.113.1.1.2.21.2.1.1.4INTEGER {normal(1), loop(2), error(3), none(4)}read-onlycurrent
swL2MultiFilter
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.22
swL2McastFilterTable
OBJECT-TYPE
A table that contains information about the multicast filter address.
1.3.6.1.4.1.171.11.113.1.1.2.22.2not-accessiblecurrent
swL2McastFilterEntry
OBJECT-TYPE
A list of multicast filter mode information for each profile ID.
1.3.6.1.4.1.171.11.113.1.1.2.22.2.1not-accessiblecurrent
swL2McastFilterProfileIndex
OBJECT-TYPE
index for each profile
1.3.6.1.4.1.171.11.113.1.1.2.22.2.1.1INTEGER (1..24)read-onlycurrent
swL2McastFilterProfileName
OBJECT-TYPE
The multicast filter description.
1.3.6.1.4.1.171.11.113.1.1.2.22.2.1.2DisplayString (SIZE(1..32))read-writecurrent
swL2McastFilterAddOrDelState
OBJECT-TYPE
The control multicast filter address.
1.3.6.1.4.1.171.11.113.1.1.2.22.2.1.3INTEGER {none(1), add(2), delete(3)}read-writecurrent
swL2McastFilterGroupList
OBJECT-TYPE
The multicast filter address group list.
1.3.6.1.4.1.171.11.113.1.1.2.22.2.1.4DisplayStringread-writecurrent
swL2McastFilterStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.11.113.1.1.2.22.2.1.5RowStatusread-createcurrent
swL2McastFilterPortTable
OBJECT-TYPE
A table that is used to bind port to profile ID.
1.3.6.1.4.1.171.11.113.1.1.2.22.3not-accessiblecurrent
swL2McastFilterPortEntry
OBJECT-TYPE
A list of information that is used to bind port to profile ID.
1.3.6.1.4.1.171.11.113.1.1.2.22.3.1not-accessiblecurrent
swL2McastFilterPortGroupPortIndex
OBJECT-TYPE
The port index.
1.3.6.1.4.1.171.11.113.1.1.2.22.3.1.1INTEGERread-onlycurrent
swL2McastFilterPortProfileAddOrDelState
OBJECT-TYPE
The control multicast filter profile.
1.3.6.1.4.1.171.11.113.1.1.2.22.3.1.2INTEGER {none(1), add(2), delete(3)}read-writecurrent
swL2McastFilterPortProfileID
OBJECT-TYPE
This object indicates the profile ID of this entry. When read, it is always 0. When set, 0 can not be set.
1.3.6.1.4.1.171.11.113.1.1.2.22.3.1.3INTEGER (0..24)read-writecurrent
swL2McastFilterPortAccess
OBJECT-TYPE
This object indicates the access status for each port. When read, it is always none. When set, none can not be set.
1.3.6.1.4.1.171.11.113.1.1.2.22.3.1.4INTEGER {none(0), permit(1), deny(2)}read-writecurrent
swL2McastFilterPortMaxGroupTable
OBJECT-TYPE
A table that contains information about the max group number based on port.
1.3.6.1.4.1.171.11.113.1.1.2.22.4not-accessiblecurrent
swL2McastFilterPortMaxGroupEntry
OBJECT-TYPE
A list of max group number information for each port.
1.3.6.1.4.1.171.11.113.1.1.2.22.4.1not-accessiblecurrent
swL2McastFilterPortMaxGroupPortIndex
OBJECT-TYPE
The port index.
1.3.6.1.4.1.171.11.113.1.1.2.22.4.1.1INTEGERread-onlycurrent
swL2McastFilterPortMaxGroup
OBJECT-TYPE
The max group numbers. The default is 256.
1.3.6.1.4.1.171.11.113.1.1.2.22.4.1.2INTEGER (1..1024)read-writecurrent
swL2McastFilterPortInfoTable
OBJECT-TYPE
A table that contains information about all of the multicast groups for the ports.
1.3.6.1.4.1.171.11.113.1.1.2.22.5not-accessiblecurrent
swL2McastFilterPortInfoEntry
OBJECT-TYPE
A list of information about all of the multicast groups for each port.
1.3.6.1.4.1.171.11.113.1.1.2.22.5.1not-accessiblecurrent
swL2McastFilterPortInfoPortIndex
OBJECT-TYPE
The port index.
1.3.6.1.4.1.171.11.113.1.1.2.22.5.1.1INTEGERread-onlycurrent
swL2McastFilterPortInfoProfileID
OBJECT-TYPE
The multicast filter address profile ID.
1.3.6.1.4.1.171.11.113.1.1.2.22.5.1.2DisplayStringread-onlycurrent
swL2McastFilterPortInfoAccess
OBJECT-TYPE
This object indicates the access status for each port.
1.3.6.1.4.1.171.11.113.1.1.2.22.5.1.3INTEGER {permit(1), deny(2)}read-onlycurrent
swL2VlanMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.23
swL2VlanAdvertisementTable
OBJECT-TYPE
A table containing the advertisement state for each VLAN configured into the device by (local or network) management.
1.3.6.1.4.1.171.11.113.1.1.2.23.1not-accessiblecurrent
swL2VlanAdvertisementEntry
OBJECT-TYPE
The advertisement state for each VLAN configured into the device.
1.3.6.1.4.1.171.11.113.1.1.2.23.1.1not-accessiblecurrent
swL2VlanIndex
OBJECT-TYPE
The VLAN-ID or other identifier referring to this VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.23.1.1.1INTEGER (1..4094)read-onlycurrent
swL2VlanName
OBJECT-TYPE
An administratively assigned string, which may be used to identify the VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.23.1.1.2DisplayString (SIZE(0..32))read-onlycurrent
swL2VlanAdvertiseState
OBJECT-TYPE
This object indicates the advertise status of this VLAN entry.
1.3.6.1.4.1.171.11.113.1.1.2.23.1.1.3INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2VlanMultiplyMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.23.2
swL2VlanMultiplyVlanList
OBJECT-TYPE
This object specifies the VLAN ID List.
1.3.6.1.4.1.171.11.113.1.1.2.23.2.1DisplayString (SIZE(0..255))read-writecurrent
swL2VlanMultiplyAdvertisement
OBJECT-TYPE
This object specifies the advertisement state.
1.3.6.1.4.1.171.11.113.1.1.2.23.2.2INTEGER {other(1), enabled(2), disabled(3)}read-writecurrent
swL2VlanMultiplyPortList
OBJECT-TYPE
Specifies the port list.
1.3.6.1.4.1.171.11.113.1.1.2.23.2.3PortListread-writecurrent
swL2VlanMultiplyPortListAction
OBJECT-TYPE
Specifies the action for the port list which specified by swL2VlanMultiplyPortList.
1.3.6.1.4.1.171.11.113.1.1.2.23.2.4INTEGER {other(1), add-tagged(2), add-untagged(3), add-forbidden(4), delete(5)}read-writecurrent
swL2VlanMultiplyAction
OBJECT-TYPE
Specifies the action for VLANs. other: no action. create: the VLANs specified by swL2VlanMultiplyVlanList would be created at a time. configure: the VLANs specified by swL2VlanMultiplyVlanList would be configured at a time. delete: the VLANs specified by swL2VlanMultiplyVlanList would be deleted at a time.
1.3.6.1.4.1.171.11.113.1.1.2.23.2.5INTEGER {other(1), create(2), configure(3), delete(4)}read-writecurrent
swL2PVIDAutoAssignmentState
OBJECT-TYPE
This object controls the PVID auto assigment state. If 'Auto-assign PVID' is disabled, PVID only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change PVID. If 'Auto-assign PVID' is enabled, PVID will be possibly changed by PVID or VLAN configuration. When user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. In the form of VLAN list command, PVID is updated with last item of VLAN list. When user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned with 'default VLAN'.
1.3.6.1.4.1.171.11.113.1.1.2.23.3INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DhcpLocalRelayMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.113.1.1.2.24
swL2DhcpLocalRelayState
OBJECT-TYPE
This object indicates the status of the DHCP local relay function of the switch.
1.3.6.1.4.1.171.11.113.1.1.2.24.1INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2DhcpLocalRelayVLANTable
OBJECT-TYPE
This table is used to manage the DHCP local relay status for each VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.24.2not-accessiblecurrent
swL2DhcpLocalRelayVLANEntry
OBJECT-TYPE
This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
1.3.6.1.4.1.171.11.113.1.1.2.24.2.1not-accessiblecurrent
swL2DhcpLocalRelayVLANID
OBJECT-TYPE
This object shows the VIDs of the current VLANS in the switch.
1.3.6.1.4.1.171.11.113.1.1.2.24.2.1.1INTEGER (1..4094)read-onlycurrent
swL2DhcpLocalRelayVLANState
OBJECT-TYPE
This object indicates the status of the DHCP relay function of the VLAN.
1.3.6.1.4.1.171.11.113.1.1.2.24.2.1.2INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent

Notifications

NameOIDStatus
swL2PortSecurityViolationTrap
NOTIFICATION-TYPE
When the port_security trap is enabled, if there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out.
1.3.6.1.4.1.171.11.113.1.1.2.20.0.1current
swL2macNotification
NOTIFICATION-TYPE
This trap indicates the MAC address variations in the address table.
1.3.6.1.4.1.171.11.113.1.1.2.20.0.2current
swL2PortLoopOccurred
NOTIFICATION-TYPE
The trap is sent when a Port loop occurs.
1.3.6.1.4.1.171.11.113.1.1.2.20.0.3current
swL2PortLoopRestart
NOTIFICATION-TYPE
The trap is sent when a Port loop restarts after the interval time.
1.3.6.1.4.1.171.11.113.1.1.2.20.0.4current
swL2VlanLoopOccurred
NOTIFICATION-TYPE
The trap is sent when a Port with a VID loop occurs.
1.3.6.1.4.1.171.11.113.1.1.2.20.0.5current
swL2VlanLoopRestart
NOTIFICATION-TYPE
The trap is sent when a Port with a VID loop restarts after the interval time.
1.3.6.1.4.1.171.11.113.1.1.2.20.0.6current