MIBs Depot

DES3028-L2MGMT-MIB

Registered at
1.3.6.1.4.1.171.11.63.6.2
Last updated
1908-10-14 00:00
Organization
D-Link, Inc.
Namespace
dlink
Source file
DES3028-L2MGMT-MIB
Digest
sha256:dda3c7af914aad3002b9703fd7c010bf3b2da56ff3b9d8bec1131633ae0243f1

Description

The Structure of Layer 2 Network Management Information for enterprise.

Contact

http://support.dlink.com

Imports

FromSymbols
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIInteger32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, RowStatus, TEXTUAL-CONVENTION, TruthValue
SWPRIMGMT-DES30XXP-MIBdes3028

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DES3028-L2MGMT-MIB
DLINK-ID-REC-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC
SWPRIMGMT-DES30XXP-MIB

Textual conventions

NameOIDSyntaxAccessStatus
MacAddress
type
PortList
type
VlanId
type

Objects

NameOIDSyntaxAccessStatus
swL2DevMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.1
swL2DevInfo
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.1.1
swL2DevInfoFrontPanelLedStatus
OBJECT-TYPE
This object is a set of system LED indications. When log in system DES3028/DES3052 which do not support POE, the first two octets is defined as system LED. The first LED is power LED. The second LED is console LED. When log in system DES3028p/DES3052p which support POE, the first four octets are defined as system LED. The first octet is 0x02 and the second octet is 0x01 when in normal mode. Contrarily, the first octet is 0x01 and the second octet is 0x02 when in poe mode. The third octet indicates the power LED. The fourth octet indicates the console LED. The other octets are defined as follow: start on the third or fifth octets separately correspond to system support poe or system which does not support poe indicate the logical port LED (following swL2BasePort ordering). Every two bytes are presented to a port. The first byte is presentd to the Link/Activity LED. The second byte is presented to the Speed LED. Link/Activity LED : The most significant bit is used for blink/solid: 8 = The LED blinks. The second significant bit is used for link status: 1 = link fail. 2 = link pass. Speed LED : 01 = 10Mbps. 02 = 100Mbps. 03 = 1000Mbps. The four remaining bits are currently unused and must be 0.
1.3.6.1.4.1.171.11.63.6.2.1.1.5OCTET STRING (SIZE(0..127))read-onlycurrent
swL2DevCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.1.2
swL2DevCtrlSystemReboot
OBJECT-TYPE
This object indicates the agent system reboot state. The agent always returns other(1) when this object is read.
1.3.6.1.4.1.171.11.63.6.2.1.2.1INTEGER {other(1), reboot(2), save-config-and-reboot(3), reboot-and-load-factory-default-config(4)}read-writecurrent
swL2DevCtrlSystemIP
OBJECT-TYPE
This object indicates system ip.
1.3.6.1.4.1.171.11.63.6.2.1.2.2IpAddressread-writecurrent
swL2DevCtrlSubnetMask
OBJECT-TYPE
This object indicates system subnet mask.
1.3.6.1.4.1.171.11.63.6.2.1.2.3IpAddressread-writecurrent
swL2DevCtrlDefaultGateway
OBJECT-TYPE
This object indicates system default gateway.
1.3.6.1.4.1.171.11.63.6.2.1.2.4IpAddressread-writecurrent
swL2DevCtrlManagementVlanId
OBJECT-TYPE
This object controls which Vlan includes system ip. And the Vlan should have been created.
1.3.6.1.4.1.171.11.63.6.2.1.2.5VlanIdread-writecurrent
swL2DevCtrlIGMPSnooping
OBJECT-TYPE
This object indicates layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled .
1.3.6.1.4.1.171.11.63.6.2.1.2.7INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2DevCtrlCleanAllStatisticCounter
OBJECT-TYPE
As the object is set to active, all the statistic counters will be cleared. If set to normal, do nothing.
1.3.6.1.4.1.171.11.63.6.2.1.2.12INTEGER {normal(1), active(2)}read-writecurrent
swL2DevCtrlSnmpEnableAuthenTraps
OBJECT-TYPE
Indicates whether the SNMP entity is permitted to generate authenticationFailure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authenticationFailure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant across re-initializations of the network management system.
1.3.6.1.4.1.171.11.63.6.2.1.2.13INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlRmonState
OBJECT-TYPE
This object can be enabled or disabled RMON.
1.3.6.1.4.1.171.11.63.6.2.1.2.16INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2DevCtrlIpAutoConfig
OBJECT-TYPE
Indicates the status of automatically getting configuration from TFTP server on device
1.3.6.1.4.1.171.11.63.6.2.1.2.17INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2MACNotifyState
OBJECT-TYPE
This object can enabled or disabled MAC Notification.
1.3.6.1.4.1.171.11.63.6.2.1.2.19INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2MACNotifyHistorySize
OBJECT-TYPE
This object indicates the history size of variation MAC in address table. The default value is 1 .
1.3.6.1.4.1.171.11.63.6.2.1.2.20INTEGER (1..500)read-writecurrent
swL2MACNotifyInterval
OBJECT-TYPE
This object indicates the time interval in second for trigger the MAC notify message.
1.3.6.1.4.1.171.11.63.6.2.1.2.21INTEGER (1..2147483647)read-writecurrent
swL2DevCtrlLLDPState
OBJECT-TYPE
Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For the receiving of LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
1.3.6.1.4.1.171.11.63.6.2.1.2.22INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlLLDPForwardMessageState
OBJECT-TYPE
When lldp is disabled and lldp forward_message is enabled, the received LLDP Data Units packet will be forwarded.
1.3.6.1.4.1.171.11.63.6.2.1.2.23INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlAsymVlanState
OBJECT-TYPE
This object enables or disables the asymmetric VLAN feature of the device.
1.3.6.1.4.1.171.11.63.6.2.1.2.24INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2IGMPSnoopingMulticastVlanState
OBJECT-TYPE
This indicates the global state of the igmp_snoop multicast_vlan.
1.3.6.1.4.1.171.11.63.6.2.1.2.25INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2DevCtrlVLANTrunkState
OBJECT-TYPE
This indicates the global state of the VLAN trunking feature of the device.
1.3.6.1.4.1.171.11.63.6.2.1.2.26INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2PortMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.2
swL2PortInfoTable
OBJECT-TYPE
A table that contains information about every port.
1.3.6.1.4.1.171.11.63.6.2.2.1not-accessiblecurrent
swL2PortInfoEntry
OBJECT-TYPE
A list of information for each port of the device.
1.3.6.1.4.1.171.11.63.6.2.2.1.1not-accessiblecurrent
swL2PortInfoPortIndex
OBJECT-TYPE
This object indicates the module's port number.(1..Max port number in the module)
1.3.6.1.4.1.171.11.63.6.2.2.1.1.1INTEGER (1..255)read-onlycurrent
swL2PortInfoMediumType
OBJECT-TYPE
This object indicates the port type: fiber or copper.
1.3.6.1.4.1.171.11.63.6.2.2.1.1.2INTEGER {copper(100), fiber(101)}read-onlycurrent
swL2PortInfoLinkStatus
OBJECT-TYPE
This object indicates the port link status.
1.3.6.1.4.1.171.11.63.6.2.2.1.1.4INTEGER {other(1), link-pass(2), link-fail(3)}read-onlycurrent
swL2PortInfoNwayStatus
OBJECT-TYPE
This object indicates the port speed and duplex mode.
1.3.6.1.4.1.171.11.63.6.2.2.1.1.5INTEGER {auto(1), half-10Mbps(2), full-10Mbps(3), half-100Mbps(4), full-100Mbps(5), half-1Gigabps(6), full-1Gigabps(7)}read-onlycurrent
swL2PortCtrlTable
OBJECT-TYPE
A table that contains control information about every port.
1.3.6.1.4.1.171.11.63.6.2.2.2not-accessiblecurrent
swL2PortCtrlEntry
OBJECT-TYPE
A list of control information for each port of the device.
1.3.6.1.4.1.171.11.63.6.2.2.2.1not-accessiblecurrent
swL2PortCtrlPortIndex
OBJECT-TYPE
This object indicates the module's port number.(1..Max port number in the module)
1.3.6.1.4.1.171.11.63.6.2.2.2.1.1INTEGER (1..255)read-onlycurrent
swL2PortCtrlPortMediumType
OBJECT-TYPE
This object indicates the port type: fiber or copper.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.2INTEGER {copper(100), fiber(101)}read-writecurrent
swL2PortCtrlAdminState
OBJECT-TYPE
This object decides whether the port is enabled or disabled.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.3INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortCtrlNwayState
OBJECT-TYPE
Choose the port speed, duplex mode, and N-Way function mode.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.4INTEGER {nway-auto(1), nway-disabled-10Mbps-Half(2), nway-disabled-10Mbps-Full(3), nway-disabled-100Mbps-Half(4), nway-disabled-100Mbps-Full(5), nway-disabled-1Gigabps-Full(7), nway-disabled-1Gigabps-Full-Master(8), nway-disabled-1Gigabps-Full-Slave(9)}read-writecurrent
swL2PortCtrlFlowCtrlState
OBJECT-TYPE
Set the flow control function as enabled or disabled.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.5INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortCtrlDescription
OBJECT-TYPE
The object describes the ports in text.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.6DisplayString (SIZE(0..32))read-writecurrent
swL2PortCtrlAddressLearning
OBJECT-TYPE
This object decides whether the address learning is enabled or disabled.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.7INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortCtrlMACNotifyState
OBJECT-TYPE
This object sets each port's MAC notification state.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.8INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2PortCtrlMulticastfilter
OBJECT-TYPE
This object decides the multicast packet filtering mode on this port.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.9INTEGER {forward-unregistered-groups(2), filter-unregistered-groups(3)}read-writecurrent
swL2PortCtrlMDIXState
OBJECT-TYPE
This object configures the MDIX setting of the port. The value 'other' is for those entries in which MDIX is not applicable.
1.3.6.1.4.1.171.11.63.6.2.2.2.1.10INTEGER {auto(1), normal(2), cross(3), other(4)}read-writecurrent
swL2PortErrTable
OBJECT-TYPE
A table that contains information about the Err port.
1.3.6.1.4.1.171.11.63.6.2.2.3not-accessiblecurrent
swL2PortErrEntry
OBJECT-TYPE
A list of information for the err port of the device.
1.3.6.1.4.1.171.11.63.6.2.2.3.1not-accessiblecurrent
swL2PortErrPortIndex
OBJECT-TYPE
This object indicates the module's port number.(1..Max port number in the module)
1.3.6.1.4.1.171.11.63.6.2.2.3.1.1INTEGER (1..255)read-onlycurrent
swL2PortErrPortState
OBJECT-TYPE
This object decides whether the port state is enabled or disabled.
1.3.6.1.4.1.171.11.63.6.2.2.3.1.2INTEGER {disabled(1), enabled(2)}read-onlycurrent
swL2PortErrPortStatus
OBJECT-TYPE
This object decides whether the PortStatus is err-disabled.
1.3.6.1.4.1.171.11.63.6.2.2.3.1.3INTEGER {other(1), err-disabled(2)}read-onlycurrent
swL2PortErrPortReason
OBJECT-TYPE
This object decides whether the PortStatus STP is LBD or Storm control.
1.3.6.1.4.1.171.11.63.6.2.2.3.1.4INTEGER {stp-lbd(1), storm-control(2)}read-onlycurrent
swL2PortErrDescription
OBJECT-TYPE
The object describes the ports in text.
1.3.6.1.4.1.171.11.63.6.2.2.3.1.5DisplayString (SIZE(0..32))read-onlycurrent
swL2QOSMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.3
swL2QOSBandwidthControlTable
OBJECT-TYPE
.
1.3.6.1.4.1.171.11.63.6.2.3.1not-accessiblecurrent
swL2QOSBandwidthControlEntry
OBJECT-TYPE
A list of information contained in swL2QOSBandwidthControlTable.
1.3.6.1.4.1.171.11.63.6.2.3.1.1not-accessiblecurrent
swL2QOSBandwidthPortIndex
OBJECT-TYPE
Indicates the port.
1.3.6.1.4.1.171.11.63.6.2.3.1.1.1INTEGER (1..650)read-onlycurrent
swL2QOSBandwidthRxRate
OBJECT-TYPE
Indicates the RX Rate(Mbit/sec) of the specifed port. A value of 1024000 means no limit.
1.3.6.1.4.1.171.11.63.6.2.3.1.1.2INTEGER (64..1024000)read-writecurrent
swL2QOSBandwidthTxRate
OBJECT-TYPE
Indicates the TX Rate(Mbit/sec) of the specifed port. A value of 1024000 means no limit.
1.3.6.1.4.1.171.11.63.6.2.3.1.1.3INTEGER (64..1024000)read-writecurrent
swL2QOSBandwidthRadiusRxRate
OBJECT-TYPE
The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate.
1.3.6.1.4.1.171.11.63.6.2.3.1.1.4INTEGERread-onlycurrent
swL2QOSBandwidthRadiusTxRate
OBJECT-TYPE
The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate.
1.3.6.1.4.1.171.11.63.6.2.3.1.1.5INTEGERread-onlycurrent
swL2QOSSchedulingTable
OBJECT-TYPE
.
1.3.6.1.4.1.171.11.63.6.2.3.2not-accessiblecurrent
swL2QOSSchedulingEntry
OBJECT-TYPE
A list of information contained in the swL2QOSSchedulingTable.
1.3.6.1.4.1.171.11.63.6.2.3.2.1not-accessiblecurrent
swL2QOSSchedulingClassIndex
OBJECT-TYPE
Indicates the hardware queue number.
1.3.6.1.4.1.171.11.63.6.2.3.2.1.1INTEGER (0..3)read-onlycurrent
swL2QOSSchedulingMaxWeight
OBJECT-TYPE
1.3.6.1.4.1.171.11.63.6.2.3.2.1.4INTEGER (1..55)read-writecurrent
swL2QOSSchedulingMechanism
OBJECT-TYPE
Indicates the mechanism of QOS scheduling.
1.3.6.1.4.1.171.11.63.6.2.3.2.1.5INTEGER {strict(1), roundrobin(2), weightfair(3)}read-onlycurrent
swL2QOS8021pUserPriorityTable
OBJECT-TYPE
.
1.3.6.1.4.1.171.11.63.6.2.3.3not-accessiblecurrent
swL2QOS8021pUserPriorityEntry
OBJECT-TYPE
A list of information contained in the swL2QOS8021pUserPriorityTable.
1.3.6.1.4.1.171.11.63.6.2.3.3.1not-accessiblecurrent
swL2QOS8021pUserPriorityIndex
OBJECT-TYPE
The 802.1p user priority.
1.3.6.1.4.1.171.11.63.6.2.3.3.1.1INTEGER (0..7)read-onlycurrent
swL2QOS8021pUserPriorityClass
OBJECT-TYPE
The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).
1.3.6.1.4.1.171.11.63.6.2.3.3.1.2INTEGER (0..3)read-writecurrent
swL2QOS8021pDefaultPriorityTable
OBJECT-TYPE
.
1.3.6.1.4.1.171.11.63.6.2.3.4not-accessiblecurrent
swL2QOS8021pDefaultPriorityEntry
OBJECT-TYPE
A list of information contained in the swL2QOS8021pDefaultPriorityTable.
1.3.6.1.4.1.171.11.63.6.2.3.4.1not-accessiblecurrent
swL2QOS8021pDefaultPriorityIndex
OBJECT-TYPE
Indicates the port number.
1.3.6.1.4.1.171.11.63.6.2.3.4.1.1INTEGER (1..650)read-onlycurrent
swL2QOS8021pDefaultPriority
OBJECT-TYPE
The priority value to assign to untagged packets received by the switch ports on the switch.
1.3.6.1.4.1.171.11.63.6.2.3.4.1.2INTEGER (0..7)read-writecurrent
swL2QOS8021pRadiusPriority
OBJECT-TYPE
Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.
1.3.6.1.4.1.171.11.63.6.2.3.4.1.3INTEGERread-onlycurrent
swL2QOSSchedulingMechanismCtrl
OBJECT-TYPE
This object can control QOS scheduling Mechanism.
1.3.6.1.4.1.171.11.63.6.2.3.5INTEGER {strict(1), weightfair(2), none(3)}read-writecurrent
swL2TrunkMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.4
swPortTrunkMaxEntries
OBJECT-TYPE
The max entries of the swPortTrunkTable
1.3.6.1.4.1.171.11.63.6.2.4.1Integer32read-onlycurrent
swPortTrunkMaxPortMembers
OBJECT-TYPE
The max number of ports allowed in a trunk.
1.3.6.1.4.1.171.11.63.6.2.4.2Integer32read-onlycurrent
swPortTrunkTable
OBJECT-TYPE
This table specifies the port membership for each logical link.
1.3.6.1.4.1.171.11.63.6.2.4.3not-accessiblecurrent
swPortTrunkEntry
OBJECT-TYPE
A list of information that specifies which port group forms a single logical link.
1.3.6.1.4.1.171.11.63.6.2.4.3.1not-accessiblecurrent
swPortTrunkIndex
OBJECT-TYPE
The index of logical port trunk.
1.3.6.1.4.1.171.11.63.6.2.4.3.1.1Integer32 (1..3)read-onlycurrent
swPortTrunkMasterPort
OBJECT-TYPE
The object indicates the master port number of the port trunk entry. The first port of the trunk is implicitly configured to be the master logical port. When using a Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be the same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
1.3.6.1.4.1.171.11.63.6.2.4.3.1.2Integer32read-createcurrent
swPortTrunkPortList
OBJECT-TYPE
Indicate member ports of a logical trunk.
1.3.6.1.4.1.171.11.63.6.2.4.3.1.3PortListread-createcurrent
swPortTrunkType
OBJECT-TYPE
This object indicates the type of this entry.
1.3.6.1.4.1.171.11.63.6.2.4.3.1.4INTEGER {static(1), lacp(2)}read-createcurrent
swPortTrunkActivePort
OBJECT-TYPE
This object indicates the active ports of this entry.
1.3.6.1.4.1.171.11.63.6.2.4.3.1.5PortListread-onlycurrent
swPortTrunkState
OBJECT-TYPE
This object indicates the status of this entry. when the state is CreatAndGo (4),the type of trunk is static (1); when the state is CreatAndWait (5), the type of trunk is lacp(2).
1.3.6.1.4.1.171.11.63.6.2.4.3.1.6RowStatusread-createcurrent
swPortTrunkFloodingPort
OBJECT-TYPE
The flooding port of every trunk.
1.3.6.1.4.1.171.11.63.6.2.4.3.1.7Integer32read-onlycurrent
swL2TrunkAlgorithm
OBJECT-TYPE
This object configures part of the packet to be examined by the switch when selecting the egress port for transmitting load-sharing data.
1.3.6.1.4.1.171.11.63.6.2.4.4INTEGER {other(1), mac-source(2), mac-destination(3), mac-source-dest(4)}read-writecurrent
swL2TrunkLACPPortTable
OBJECT-TYPE
This table specifies which port group a set of ports (up to 8) is formed into a single logical link.
1.3.6.1.4.1.171.11.63.6.2.4.5not-accessiblecurrent
swL2TrunkLACPPortEntry
OBJECT-TYPE
A list of information specifies which port group a set of ports (up to 8) is formed into a single logical link.
1.3.6.1.4.1.171.11.63.6.2.4.5.1not-accessiblecurrent
swL2TrunkLACPPortIndex
OBJECT-TYPE
The index of the logical port LACP.
1.3.6.1.4.1.171.11.63.6.2.4.5.1.1INTEGER (0..65535)read-onlycurrent
swL2TrunkLACPPortState
OBJECT-TYPE
The state of the logical port LACP.
1.3.6.1.4.1.171.11.63.6.2.4.5.1.2INTEGER {active(1), passive(2)}read-writecurrent
swL2TrunkVLANTable
OBJECT-TYPE
This table is used to manage the VLAN trunking feature of the device.
1.3.6.1.4.1.171.11.63.6.2.4.6not-accessiblecurrent
swL2TrunkVLANEntry
OBJECT-TYPE
This object is used to configure the VLAN trunking settings for each port.
1.3.6.1.4.1.171.11.63.6.2.4.6.1not-accessiblecurrent
swL2TrunkVLANPort
OBJECT-TYPE
This object indicates the port being configured.
1.3.6.1.4.1.171.11.63.6.2.4.6.1.1INTEGER (0..65535)read-onlycurrent
swL2TrunkVLANState
OBJECT-TYPE
The state of the logical port LACP.
1.3.6.1.4.1.171.11.63.6.2.4.6.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
swPortMirrorPackage
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.6
swPortMirrorRxPortList
OBJECT-TYPE
This object indicates the Rx port list of ports to be sniffed.
1.3.6.1.4.1.171.11.63.6.2.6.2PortListread-writecurrent
swPortMirrorTxPortList
OBJECT-TYPE
This object indicates the Tx port list of ports to be sniffed.
1.3.6.1.4.1.171.11.63.6.2.6.3PortListread-writecurrent
swPortMirrorTargetPort
OBJECT-TYPE
This object indicates the switch whose port will sniff another port. A trunk port member cannot be configured as a target Snooping port. The port number is the sequential (logical) number which is also applied to the bridge MIB, etc.
1.3.6.1.4.1.171.11.63.6.2.6.4Integer32read-writecurrent
swPortMirrorState
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.11.63.6.2.6.5INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swIGMPPackage
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.7
swL2IGMPMaxSupportedVlans
OBJECT-TYPE
The maximum number of VLANs in the layer 2 IGMP control table (swL2IGMPCtrlTable).
1.3.6.1.4.1.171.11.63.6.2.7.1INTEGER (0..65535)read-onlycurrent
swL2IGMPMaxIpGroupNumPerVlan
OBJECT-TYPE
The maximum number of multicast IP groups per VLAN in the layer 2 IGMP information table (swL2IGMPQueryInfoTable).
1.3.6.1.4.1.171.11.63.6.2.7.2INTEGER (0..65535)read-onlycurrent
swL2IGMPCtrlTable
OBJECT-TYPE
The table controls the VLAN's IGMP function. Its scale depends on the current VLAN state (swL2VlanInfoStatus). If the VLAN mode is disabled, there is only one entry in the table, with index 1. If VLAN is in Port-Based or 802.1q mode, the number of entries can be up to 12, with an index range from 1 to 12.
1.3.6.1.4.1.171.11.63.6.2.7.3not-accessiblecurrent
swL2IGMPCtrlEntry
OBJECT-TYPE
An entry in IGMP control table (swL2IGMPCtrlTable). The entry is effective only when IGMP captures the switch (swL2DevCtrlIGMPSnooping) is enabled.
1.3.6.1.4.1.171.11.63.6.2.7.3.1not-accessiblecurrent
swL2IGMPCtrlVid
OBJECT-TYPE
This object indicates the IGMP control entry's VLAN ID. If VLAN is disabled, the VID is always 0 and cannot be changed by management users. If VLAN is in Port-Based mode, the VID is arranged from 1 to 12, fixed form. If VLAN is in 802.1q mode, the VID setting can vary from 1 to 4094 by management user, and the VID in each entry must be unique in the IGMP Control Table.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.1INTEGER (0..65535)read-onlycurrent
swL2IGMPQueryInterval
OBJECT-TYPE
The frequency at which IGMP Host-Query packets are transmitted on this switch.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.2INTEGER (1..65535)read-writecurrent
swL2IGMPMaxResponseTime
OBJECT-TYPE
The maximum query response time on this switch.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.3INTEGER (1..25)read-writecurrent
swL2IGMPRobustness
OBJECT-TYPE
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.4INTEGER (1..255)read-writecurrent
swL2IGMPLastMemberQueryInterval
OBJECT-TYPE
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.5INTEGER (1..25)read-writecurrent
swL2IGMPHostTimeout
OBJECT-TYPE
The timer value for sending IGMP query packets when none was sent by the host in the LAN. The timer works on a per-VLAN basis. Our device will be activated to send the query message if the timer expires. Please reference RFC2236-1997.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.6INTEGER (1..16711450)read-writecurrent
swL2IGMPRouteTimeout
OBJECT-TYPE
The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.7INTEGER (1..16711450)read-writecurrent
swL2IGMPLeaveTimer
OBJECT-TYPE
When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.8INTEGER (1..16711450)read-writecurrent
swL2IGMPQueryState
OBJECT-TYPE
This object decides if the IGMP query is enabled or disabled.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.9INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2IGMPCurrentState
OBJECT-TYPE
This object indicates the current IGMP query state.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.10INTEGER {other(1), querier(2), non-querier(3)}read-onlycurrent
swL2IGMPCtrlState
OBJECT-TYPE
This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable (2) - IGMP function is disabled for this entry. enable (3) - IGMP function is enabled for this entry.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.11INTEGER {other(1), disable(2), enable(3)}read-writecurrent
swL2IGMPFastLeave
OBJECT-TYPE
1.3.6.1.4.1.171.11.63.6.2.7.3.1.12INTEGER {other(1), disable(2), enable(3)}read-writecurrent
swL2IGMPDynIPMultVlanState
OBJECT-TYPE
This object is used to disable or enable the dynamic IP multicast feature in this VLAN.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.13INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2IGMPDynIPMultVlanAge
OBJECT-TYPE
This object is used to enable or disable aging on the dynamic IP multicast entry in this VLAN.
1.3.6.1.4.1.171.11.63.6.2.7.3.1.14INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2IGMPQueryInfoTable
OBJECT-TYPE
The table contains the number of current IGMP query packets which are captured by this device, as well as the IGMP query packets sent by the device.
1.3.6.1.4.1.171.11.63.6.2.7.4not-accessiblecurrent
swL2IGMPQueryInfoEntry
OBJECT-TYPE
Information about current IGMP query information, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN entry are all enabled.
1.3.6.1.4.1.171.11.63.6.2.7.4.1not-accessiblecurrent
swL2IGMPInfoVid
OBJECT-TYPE
This object indicates the VID of the associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).
1.3.6.1.4.1.171.11.63.6.2.7.4.1.1INTEGER (0..65535)read-onlycurrent
swL2IGMPInfoQueryCount
OBJECT-TYPE
This object indicates the number of query packets received since the IGMP function enabled, on a per-VLAN basis.
1.3.6.1.4.1.171.11.63.6.2.7.4.1.2INTEGER (0..65535)read-onlycurrent
swL2IGMPInfoTxQueryCount
OBJECT-TYPE
This object indicates the send count of IGMP query messages, on a per-VLAN basis. In case of the IGMP timer expiring, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.
1.3.6.1.4.1.171.11.63.6.2.7.4.1.3INTEGER (0..65535)read-onlycurrent
swL2IGMPInfoTable
OBJECT-TYPE
The table containing current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled. Note that the priority of IGMP table entries is lower than Filtering Table, i.e. if there is a table hash collision between the entries of IGMP Table and Filtering Table inside the switch H/W address table, then Filtering Table entry overwrite the colliding entry of IGMP Table. Also see swL2FilterMgmt description.
1.3.6.1.4.1.171.11.63.6.2.7.5not-accessiblecurrent
swL2IGMPInfoEntry
OBJECT-TYPE
Information about current IGMP information which was captured by this device, provided that swL2DevCtrlIGMPSnooping and swL2IGMPCtrlState of associated VLAN entry are all enabled.
1.3.6.1.4.1.171.11.63.6.2.7.5.1not-accessiblecurrent
swL2IGMPVid
OBJECT-TYPE
This object indicates the VID of an individual IGMP table entry. It shows the VID of IGMP report information captured on the network.
1.3.6.1.4.1.171.11.63.6.2.7.5.1.1INTEGER (0..65535)read-onlycurrent
swL2IGMPGroupIpAddr
OBJECT-TYPE
This object is the identify group IP address which is captured from IGMP packet, on a per-VLAN basis.
1.3.6.1.4.1.171.11.63.6.2.7.5.1.2IpAddressread-onlycurrent
swL2IGMPMacAddr
OBJECT-TYPE
This object identifies the MAC address which is corresponding to swL2IGMPGroupIpAddr, on a per-VLAN basis.
1.3.6.1.4.1.171.11.63.6.2.7.5.1.3MacAddressread-onlycurrent
swL2IGMPPortMap
OBJECT-TYPE
This object indicates which ports belong to the same multicast group, on a per-VLAN basis. Each multicast group has an octet string to indicate the port map. The most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the switch is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0' (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant). The 4 octets represent one unit port according to its logic port. If the unit is less than 32 ports, the other port will just fill this value with zeros.
1.3.6.1.4.1.171.11.63.6.2.7.5.1.4PortListread-onlycurrent
swL2IGMPIpGroupReportCount
OBJECT-TYPE
This object indicates how many report packets were received by our device corresponding with this entry that has the IGMP function enabled, on a per-VLAN basis.
1.3.6.1.4.1.171.11.63.6.2.7.5.1.5INTEGER (0..65535)read-onlycurrent
swL2IGMPRouterPortTable
OBJECT-TYPE
The information of the router port table.
1.3.6.1.4.1.171.11.63.6.2.7.6not-accessiblecurrent
swL2IGMPRouterPortEntry
OBJECT-TYPE
The entry of the swL2IGMPRouterPortTable.
1.3.6.1.4.1.171.11.63.6.2.7.6.1not-accessiblecurrent
swL2IGMPRouterPortVlanid
OBJECT-TYPE
This object indicates the VLAN ID of the router port entry.
1.3.6.1.4.1.171.11.63.6.2.7.6.1.1INTEGER (1..4094)read-onlycurrent
swL2IGMPRouterPortVlanName
OBJECT-TYPE
This object indicates the VLAN name of the router port entry.
1.3.6.1.4.1.171.11.63.6.2.7.6.1.2SnmpAdminString (SIZE(0..32))read-onlycurrent
swL2IGMPRouterPortStaticPortList
OBJECT-TYPE
This object indicates the static portlist of the router port entry.
1.3.6.1.4.1.171.11.63.6.2.7.6.1.3PortListread-writecurrent
swL2IGMPRouterPortDynamicPortList
OBJECT-TYPE
This object indicates the dynamic portlist of the router port entry.
1.3.6.1.4.1.171.11.63.6.2.7.6.1.4PortListread-onlycurrent
swL2IGMPRouterPortForbiddenPortList
OBJECT-TYPE
This object indicates the forbidden portlist of the router port entry.
1.3.6.1.4.1.171.11.63.6.2.7.6.1.5PortListread-writecurrent
swL2IGMPAccessAuthTable
OBJECT-TYPE
This table is used to manage the IGMP Access Authentication configurations of the device.
1.3.6.1.4.1.171.11.63.6.2.7.7not-accessiblecurrent
swL2IGMPAccessAuthEntry
OBJECT-TYPE
A list of manageable entities for IGMP Access Authentication. The configuration is done per port.
1.3.6.1.4.1.171.11.63.6.2.7.7.1not-accessiblecurrent
swL2IGMPAccessAuthPort
OBJECT-TYPE
The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.
1.3.6.1.4.1.171.11.63.6.2.7.7.1.1INTEGERread-onlycurrent
swL2IGMPAccessAuthState
OBJECT-TYPE
This object denotes the status of IGMP Access Authentication of the port.
1.3.6.1.4.1.171.11.63.6.2.7.7.1.2INTEGER {disabled(1), enabled(2)}read-writecurrent
swL2IGMPMulticastVlanTable
OBJECT-TYPE
Information about the IGMP snooping multicast VLAN table.
1.3.6.1.4.1.171.11.63.6.2.7.8not-accessiblecurrent
swL2IGMPMulticastVlanEntry
OBJECT-TYPE
The entry of swL2IGMPMulticastVlanTable.
1.3.6.1.4.1.171.11.63.6.2.7.8.1not-accessiblecurrent
swL2IGMPMulticastVlanid
OBJECT-TYPE
This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.1INTEGER (2..4094)read-onlycurrent
swL2IGMPMulticastVlanName
OBJECT-TYPE
This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.2DisplayString (SIZE(0..32))read-createcurrent
swL2IGMPMulticastVlanSourcePort
OBJECT-TYPE
This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.3PortListread-writecurrent
swL2IGMPMulticastVlanMemberPort
OBJECT-TYPE
This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.4PortListread-writecurrent
swL2IGMPMulticastVlanTagMemberPort
OBJECT-TYPE
This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.5PortListread-writecurrent
swL2IGMPMulticastVlanState
OBJECT-TYPE
This object can be used to enable or disable the IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.6INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2IGMPMulticastVlanReplaceSourceIp
OBJECT-TYPE
The replacement source IP of this multicast VLAN.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.7IpAddressread-writecurrent
swL2IGMPMulticastVlanRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.8RowStatusread-createcurrent
swL2IGMPMulticastVlanRemoveAllMcastAddrListAction
OBJECT-TYPE
This object indicates whether to remove all the multicast address lists from the IGMP multicast VLAN or not.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.9INTEGER {other(1), start(2)}read-writecurrent
swL2IGMPMulticastVlanUntagSourcePort
OBJECT-TYPE
This object indicates the untagged member ports to add to the multicast VLAN.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.10PortListread-writecurrent
swL2IGMPMulticastVlanRemapPriority
OBJECT-TYPE
The priority value (0 to 7) to be associated with the data traffic to be forwarded on the multicast VLAN. When set to 8, the packet's original priority will be used.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.11INTEGER (0..8)read-createcurrent
swL2IGMPMulticastVlanReplacePriority
OBJECT-TYPE
Specifies that a packet's priority will be changed by the switch based on the remap priority. This flag will only take effect when remap priority is set.
1.3.6.1.4.1.171.11.63.6.2.7.8.1.12INTEGER {true(1), false(2)}read-createcurrent
swL2IGMPMulticastVlanGroupTable
OBJECT-TYPE
The table containing the IGMP snooping multicast VLAN group information
1.3.6.1.4.1.171.11.63.6.2.7.9not-accessiblecurrent
swL2IGMPMulticastVlanGroupEntry
OBJECT-TYPE
Information about the current IGMP snooping multicast VLAN group.
1.3.6.1.4.1.171.11.63.6.2.7.9.1not-accessiblecurrent
swL2IGMPMulticastVlanGroupVid
OBJECT-TYPE
This object indicates the VID of the IGMP snooping multicast VLAN group.
1.3.6.1.4.1.171.11.63.6.2.7.9.1.1INTEGER (1..4094)read-onlycurrent
swL2IGMPMulticastVlanGroupFromIp
OBJECT-TYPE
Specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.11.63.6.2.7.9.1.2IpAddressread-onlycurrent
swL2IGMPMulticastVlanGroupToIp
OBJECT-TYPE
Specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.11.63.6.2.7.9.1.3IpAddressread-onlycurrent
swL2IGMPMulticastVlanGroupStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.11.63.6.2.7.9.1.4RowStatusread-createcurrent
swL2IGMPv3Table
OBJECT-TYPE
This table contains the IGMP snooping V3 information.
1.3.6.1.4.1.171.11.63.6.2.7.10not-accessiblecurrent
swL2IGMPv3Entry
OBJECT-TYPE
Information about the current IGMP snooping V3.
1.3.6.1.4.1.171.11.63.6.2.7.10.1not-accessiblecurrent
swL2IGMPv3SourceIPAddr
OBJECT-TYPE
This object identifies the source IP addresses from the group where they were captured from. IGMP packets, on a per-VLAN basis.
1.3.6.1.4.1.171.11.63.6.2.7.10.1.1IpAddressread-onlycurrent
swL2IGMPv3Forwarding
OBJECT-TYPE
This object identifies if the packets from the source IP addresses are forwarding or not.
1.3.6.1.4.1.171.11.63.6.2.7.10.1.2INTEGER {enabled(1), disabled(2)}read-onlycurrent
swL2IGMPv3ExpireTimer
OBJECT-TYPE
This object identifies the leaving times of the source time.
1.3.6.1.4.1.171.11.63.6.2.7.10.1.3INTEGERread-onlycurrent
swIGMPSnoopingGroupTable
OBJECT-TYPE
The table contains the current IGMP snooping group information captured by the device.
1.3.6.1.4.1.171.11.63.6.2.7.11not-accessiblecurrent
swIGMPSnoopingGroupEntry
OBJECT-TYPE
Information about the current IGMP snooping group information which has been captured by the device.
1.3.6.1.4.1.171.11.63.6.2.7.11.1not-accessiblecurrent
swIGMPSnoopingGroupVid
OBJECT-TYPE
This object indicates the VID of the individual IGMP snooping group table entry.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.1INTEGER (1..4094)read-onlycurrent
swIGMPSnoopingGroupGroupAddr
OBJECT-TYPE
This object identifies the group IP address which has been captured from the IGMP packet, on a per-VLAN basis.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.2IpAddressread-onlycurrent
swIGMPSnoopingGroupSourceAddr
OBJECT-TYPE
This object identifies the source addresses.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.3IpAddressread-onlycurrent
swIGMPSnoopingGroupIncludePortMap
OBJECT-TYPE
This object indicates the port list under INCLUDE mode.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.4PortListread-onlycurrent
swIGMPSnoopingGroupExcludePortMap
OBJECT-TYPE
This object indicates the port list under EXCLUDE mode.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.5PortListread-onlycurrent
swIGMPSnoopingGroupReportCount
OBJECT-TYPE
This object indicates how many report packets were received by our device corresponding with this entry that has the IGMP function enabled, on a per-group basis.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.6INTEGERread-onlycurrent
swIGMPSnoopingGroupUpTime
OBJECT-TYPE
This object indicates how long since the group was detected.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.7TimeTicksread-onlycurrent
swIGMPSnoopingGroupExpiryTime
OBJECT-TYPE
This object indicates the time left before this group will be aged out.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.8TimeTicksread-onlycurrent
swIGMPSnoopingGroupRouterPorts
OBJECT-TYPE
This object indicates the port number of the router ports.
1.3.6.1.4.1.171.11.63.6.2.7.11.1.9PortListread-onlycurrent
swL2IGMPDynIpMultMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.7.12
swL2IGMPDynIPMultMaxEntry
OBJECT-TYPE
This object specifies the maximum number of entries which can be learned by dynamic IP multicast.
1.3.6.1.4.1.171.11.63.6.2.7.12.1INTEGERread-writecurrent
swL2IGMPSnoopingClearDynIpMult
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.7.12.2
swL2IGMPSnoopingClearDynIpMultVID
OBJECT-TYPE
This object indicates the VLAN identifier where the data driven entries will be removed from.
1.3.6.1.4.1.171.11.63.6.2.7.12.2.1VlanIdread-writecurrent
swL2IGMPSnoopingClearDynIpMultIP
OBJECT-TYPE
This object indicates the IP address of the IGMP snooping group from which the data driven entries will be removed.
1.3.6.1.4.1.171.11.63.6.2.7.12.2.2IpAddressread-writecurrent
swL2IGMPSnoopingClearDynIpMultAction
OBJECT-TYPE
Setting this object will clear the data driven entries. all - Remove all learned data driven groups. VLAN - Clear all data driven entries in the VLAN specified in swIGMPSnoopingClearDynIpMultVID. group - Clear the group with the address specified in swL2IGMPSnoopingClearDynIpMultIP in the VLAN specified in swIGMPSnoopingClearDynIpMultVID.
1.3.6.1.4.1.171.11.63.6.2.7.12.2.3INTEGER {all(1), vlan(2), group(3), other(4)}read-writecurrent
swL2TrafficSegMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.12
swL2TrafficSegTable
OBJECT-TYPE
This table specifies the port just can forward traffic to the specific port list.
1.3.6.1.4.1.171.11.63.6.2.12.1not-accessiblecurrent
swL2TrafficSegEntry
OBJECT-TYPE
A list of information specifies the port with its traffic forward list.
1.3.6.1.4.1.171.11.63.6.2.12.1.1not-accessiblecurrent
swL2TrafficSegPort
OBJECT-TYPE
The port number of the logical port.
1.3.6.1.4.1.171.11.63.6.2.12.1.1.1INTEGER (0..65535)read-onlycurrent
swL2TrafficSegForwardPorts
OBJECT-TYPE
The port list that the specific port can forward traffic.
1.3.6.1.4.1.171.11.63.6.2.12.1.1.2PortListread-writecurrent
swL2PortSecurityMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.15
swL2PortSecurityControlTable
OBJECT-TYPE
The port security feature controls the address leaning capability and the traffic forwarding decision. Each port can have this function enabled or disabled. When it is enabled and a number is given said N, which allows N addresses to be learned at this port, the first N learned addresses are locked at this port as a static entry. When the learned address number reaches N, any incoming packet without learned source addresses are discarded (e.g. dropped) and no more new addresses can be learned at this port.
1.3.6.1.4.1.171.11.63.6.2.15.1not-accessiblecurrent
swL2PortSecurityControlEntry
OBJECT-TYPE
A list of information contained in the swL2PortSecurityControlTable.
1.3.6.1.4.1.171.11.63.6.2.15.1.1not-accessiblecurrent
swL2PortSecurityPortIndex
OBJECT-TYPE
Indicates a secured port to lock address learning.
1.3.6.1.4.1.171.11.63.6.2.15.1.1.1INTEGER (1..255)read-onlycurrent
swL2PortSecurityMaxLernAddr
OBJECT-TYPE
Indicates the allowable number of addresses to be learned at this port.
1.3.6.1.4.1.171.11.63.6.2.15.1.1.2INTEGER (0..16)read-writecurrent
swL2PortSecurityMode
OBJECT-TYPE
Indicates the mode of locking address. In deleteOnTimeout (3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that can be learned has to be increased by one. In deleteOnReset (4) mode - never age out the locked addresses unless restarting the system to prevent port movement or intrusion.
1.3.6.1.4.1.171.11.63.6.2.15.1.1.3INTEGER {other(1), permanent(2), deleteOnTimeout(3), deleteOnReset(4)}read-writecurrent
swL2PortSecurityAdmState
OBJECT-TYPE
Indicates an administration state of locking address.
1.3.6.1.4.1.171.11.63.6.2.15.1.1.4INTEGER {other(1), enable(2), disable(3)}read-writecurrent
swL2PortSecurityTrapLogState
OBJECT-TYPE
When enabled (2), whenever there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out and the relevant information will be logged in the system.
1.3.6.1.4.1.171.11.63.6.2.15.2INTEGER {other(1), enable(2), disable(3)}read-writecurrent
swL2PortSecurityDelCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.15.3
swL2PortSecurityDelVlanName
OBJECT-TYPE
Indicates the VLAN name.
1.3.6.1.4.1.171.11.63.6.2.15.3.1DisplayString (SIZE(0..32))read-writecurrent
swL2PortSecurityDelPort
OBJECT-TYPE
Indicates the port. 0 means the function dose not work now.
1.3.6.1.4.1.171.11.63.6.2.15.3.2INTEGER (0..768)read-writecurrent
swL2PortSecurityDelMacAddress
OBJECT-TYPE
Specifies the MAC address.
1.3.6.1.4.1.171.11.63.6.2.15.3.3MacAddressread-writecurrent
swL2PortSecurityDelActivity
OBJECT-TYPE
1.3.6.1.4.1.171.11.63.6.2.15.3.4INTEGER {none(1), start(2)}read-writecurrent
swL2CosMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.17
swL2CosPriorityCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.17.3
swL2CosPriorityTable
OBJECT-TYPE
Used to show and configure per port priority-based QoS features on the switch.
1.3.6.1.4.1.171.11.63.6.2.17.3.1not-accessiblecurrent
swL2CosPriorityEntry
OBJECT-TYPE
A list of information contained in the swL2CosPriorityTable.
1.3.6.1.4.1.171.11.63.6.2.17.3.1.1not-accessiblecurrent
swL2CosPriorityPort
OBJECT-TYPE
The port number of CoS Priority.
1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.1INTEGER (1..65535)read-onlycurrent
swL2CosPriorityPortPRI
OBJECT-TYPE
Indicates the port_priority state for CoS.
1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.2INTEGER {other(1), disable(2), enable(3)}read-writecurrent
swL2CosPriorityEtherPRI
OBJECT-TYPE
Enable Ethernet frame based priority. When set ether8021p (2), enable 802.1p QoS; When set macBase (3), enable MAC-based QoS; When set disable (1), disable Ethernet frame based priority.
1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.3INTEGER {disable(1), ether8021p(2), macBase(3)}read-writecurrent
swL2CosPriorityIpPRI
OBJECT-TYPE
Enable IP priority QoS. When set tos (2), enable TOS based QoS; When set dscp (3), enable DSCP based QoS; When set disable (1), disable IP priority QoS.
1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.4INTEGER {disable(1), tos(2), dscp(3)}read-writecurrent
swL2CosPriorityNone
OBJECT-TYPE
When read, it always returns invalid (2); when write valid (1), it disables all priority in this table.
1.3.6.1.4.1.171.11.63.6.2.17.3.1.1.5INTEGER {valid(1), invalid(2)}read-writecurrent
swL2CosPortPRITable
OBJECT-TYPE
Used to show port-to-class mappings and map specific port to one of the hardware queues available on the switch.
1.3.6.1.4.1.171.11.63.6.2.17.3.2not-accessiblecurrent
swL2CosPortPRIEntry
OBJECT-TYPE
A list of information contained in the swL2CosPortPRITable.
1.3.6.1.4.1.171.11.63.6.2.17.3.2.1not-accessiblecurrent
swL2CosPortPRIIndex
OBJECT-TYPE
Indicates the CoS Priority PortPRI.
1.3.6.1.4.1.171.11.63.6.2.17.3.2.1.1INTEGER (1..65535)read-onlycurrent
swL2CosPortPRIClass
OBJECT-TYPE
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges. And you can set a value of 0 or 3 only, you can't set a value 1 or 2.
1.3.6.1.4.1.171.11.63.6.2.17.3.2.1.2INTEGER (0..3)read-writecurrent
swL2CosMacBasePRITable
OBJECT-TYPE
Used to show MAC priority map to traffic class and map the destination MAC address in incoming packet to one of the hardware queues available on the switch.
1.3.6.1.4.1.171.11.63.6.2.17.3.3not-accessiblecurrent
swL2CosMacBasePRIEntry
OBJECT-TYPE
A list of information contained in the swL2CosMacBasePRITable.
1.3.6.1.4.1.171.11.63.6.2.17.3.3.1not-accessiblecurrent
swL2CosMacBasePRIIndex
OBJECT-TYPE
Indicates the CoS Priority MacBasePRI.
1.3.6.1.4.1.171.11.63.6.2.17.3.3.1.1MacAddressread-onlycurrent
swL2CosMacBasePRIClass
OBJECT-TYPE
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
1.3.6.1.4.1.171.11.63.6.2.17.3.3.1.2INTEGER (0..3)read-writecurrent
swL2CosTosPRITable
OBJECT-TYPE
Used to show TOS value to traffic class mapping and map the TOS value in the IP header of incoming packet to one of the four hardware queues available on the switch.
1.3.6.1.4.1.171.11.63.6.2.17.3.4not-accessiblecurrent
swL2CosTosPRIEntry
OBJECT-TYPE
A list of information contained in the swL2CosTosPRITable.
1.3.6.1.4.1.171.11.63.6.2.17.3.4.1not-accessiblecurrent
swL2CosTosPRIIndex
OBJECT-TYPE
Indicates the CoS Priority TosPRI.
1.3.6.1.4.1.171.11.63.6.2.17.3.4.1.1INTEGER (0..7)read-onlycurrent
swL2CosTosPRIClass
OBJECT-TYPE
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
1.3.6.1.4.1.171.11.63.6.2.17.3.4.1.2INTEGER (0..3)read-writecurrent
swL2CosDscpPRITable
OBJECT-TYPE
Used to show DSCP value to traffic class mapping and map the DSCP value in the IP header of incoming packet to one of the hardware queues available on the switch.
1.3.6.1.4.1.171.11.63.6.2.17.3.5not-accessiblecurrent
swL2CosDscpPRIEntry
OBJECT-TYPE
A list of information contained in the swL2CosDscpPRITable.
1.3.6.1.4.1.171.11.63.6.2.17.3.5.1not-accessiblecurrent
swL2CosDscpPRIIndex
OBJECT-TYPE
Indicates the CoS Priority DscpPRI.
1.3.6.1.4.1.171.11.63.6.2.17.3.5.1.1INTEGER (0..63)read-onlycurrent
swL2CosDscpPRIClass
OBJECT-TYPE
The number of the switch's hardware priority queue. The switch has 4 hardware priority queues available. They are numbered between 0 (the lowest priority queue) and 3 (the highest priority queue). If you want to set one, you must have administrator privileges.
1.3.6.1.4.1.171.11.63.6.2.17.3.5.1.2INTEGER (0..3)read-writecurrent
swL2DhcpRelayMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.18
swL2DhcpRelayState
OBJECT-TYPE
This object indicates whether the DHCP relay function is enabled or disabled.
1.3.6.1.4.1.171.11.63.6.2.18.1INTEGER {other(1), disabled(2), enabled(3)}read-writeobsolete
swL2DhcpRelayHopCount
OBJECT-TYPE
This object indicates the maximum number of router hops that the DHCP packets can cross.
1.3.6.1.4.1.171.11.63.6.2.18.2INTEGER (1..16)read-writeobsolete
swL2DhcpRelayTimeThreshold
OBJECT-TYPE
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
1.3.6.1.4.1.171.11.63.6.2.18.3INTEGER (0..65535)read-writeobsolete
swL2DhcpRelayOption82State
OBJECT-TYPE
This object indicates DHCP relay agent information option 82 function is enabled or disabled.
1.3.6.1.4.1.171.11.63.6.2.18.4INTEGER {other(1), disabled(2), enabled(3)}read-writeobsolete
swL2DhcpRelayOption82Check
OBJECT-TYPE
This object indicates the checking mechanism of DHCP relay agent information option 82 is enabled or disabled.
1.3.6.1.4.1.171.11.63.6.2.18.5INTEGER {other(1), disabled(2), enabled(3)}read-writeobsolete
swL2DhcpRelayOption82Policy
OBJECT-TYPE
This object indicates the reforwarding policy of DHCP relay agent information option 82. replace (1) - Replace the exiting option 82 field in messages. drop (2) - Discard messages with existing option 82 field. keep (3) - Retain the existing option 82 field in messages.
1.3.6.1.4.1.171.11.63.6.2.18.6INTEGER {replace(1), drop(2), keep(3)}read-writeobsolete
swL2DhcpRelayCtrlTable
OBJECT-TYPE
This table specifies the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.11.63.6.2.18.7not-accessibleobsolete
swL2DhcpRelayCtrlEntry
OBJECT-TYPE
A list of information specifies the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.11.63.6.2.18.7.1not-accessibleobsolete
swL2DhcpRelayCtrlInterfaceName
OBJECT-TYPE
The name of the IP interface.
1.3.6.1.4.1.171.11.63.6.2.18.7.1.1DisplayString (SIZE(1..12))read-onlyobsolete
swL2DhcpRelayCtrlServer
OBJECT-TYPE
The DHCP server IP address.
1.3.6.1.4.1.171.11.63.6.2.18.7.1.2IpAddressread-onlycurrent
swL2DhcpRelayCtrlState
OBJECT-TYPE
This object indicates the status of this entry. other (1) - This entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid (2) - Writing this value to the object, and then the corresponding entry will be removed from the table. valid (3) - This entry resides in the table.
1.3.6.1.4.1.171.11.63.6.2.18.7.1.3INTEGER {other(1), invalid(2), valid(3)}read-writeobsolete
swL2MgmtMIBTraps
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.20
swL2MgmtMIBTrapPrefix
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.20.0
swl2PortSecurityBidings
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.20.1
swL2PortSecurityViolationMac
OBJECT-TYPE
This object indicates the MAC address that violates the port security configuration.
1.3.6.1.4.1.171.11.63.6.2.20.1.1MacAddressaccessible-for-notifycurrent
swl2NotificationBidings
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.20.2
swL2macNotifyInfo
OBJECT-TYPE
This object indicates the last time reboot information.
1.3.6.1.4.1.171.11.63.6.2.20.2.1OCTET STRING (SIZE(0..1024))read-onlycurrent
swL2LoopDetectMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.21
swL2LoopDetectCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.21.1
swL2LoopDetectAdminState
OBJECT-TYPE
This object indicates the loopback detection status for the system.
1.3.6.1.4.1.171.11.63.6.2.21.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2LoopDetectInterval
OBJECT-TYPE
This object indicates the interval value, the range is from 1 to 32767 seconds.
1.3.6.1.4.1.171.11.63.6.2.21.1.2INTEGER (1..32767)read-writecurrent
swL2LoopDetectRecoverTime
OBJECT-TYPE
This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
1.3.6.1.4.1.171.11.63.6.2.21.1.3INTEGER (0..1000000)read-writecurrent
swL2LoopDetectPortMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.21.2
swL2LoopDetectPortTable
OBJECT-TYPE
The table specifies the loopback detection function specified by port.
1.3.6.1.4.1.171.11.63.6.2.21.2.1not-accessiblecurrent
swL2LoopDetectPortEntry
OBJECT-TYPE
The table specifies the loopback detection function specified by port.
1.3.6.1.4.1.171.11.63.6.2.21.2.1.1not-accessiblecurrent
swL2LoopDetectPortIndex
OBJECT-TYPE
This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
1.3.6.1.4.1.171.11.63.6.2.21.2.1.1.1INTEGER (1..65535)read-onlycurrent
swL2LoopDetectPortState
OBJECT-TYPE
This object indicates the loopback detection function state on the port.
1.3.6.1.4.1.171.11.63.6.2.21.2.1.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
swL2LoopDetectPortLoopStatus
OBJECT-TYPE
This object indicates the port status.
1.3.6.1.4.1.171.11.63.6.2.21.2.1.1.4INTEGER {normal(1), loop(2), error(3)}read-onlycurrent
swL2MultiFilter
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.22
swL2McastFilterTable
OBJECT-TYPE
A table that contains information about the multicast filter address.
1.3.6.1.4.1.171.11.63.6.2.22.2not-accessiblecurrent
swL2McastFilterEntry
OBJECT-TYPE
A list of multicast filter mode information for each profile ID.
1.3.6.1.4.1.171.11.63.6.2.22.2.1not-accessiblecurrent
swL2McastFilterProfileIndex
OBJECT-TYPE
index for each profile
1.3.6.1.4.1.171.11.63.6.2.22.2.1.1INTEGER (1..24)read-onlycurrent
swL2McastFilterProfileName
OBJECT-TYPE
The multicast filter description.
1.3.6.1.4.1.171.11.63.6.2.22.2.1.2DisplayString (SIZE(1..32))read-writecurrent
swL2McastFilterAddOrDelState
OBJECT-TYPE
The control multicast filter address.
1.3.6.1.4.1.171.11.63.6.2.22.2.1.3INTEGER {none(1), add(2), delete(3)}read-writecurrent
swL2McastFilterGroupList
OBJECT-TYPE
The multicast filter address group list.
1.3.6.1.4.1.171.11.63.6.2.22.2.1.4DisplayStringread-writecurrent
swL2McastFilterStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.11.63.6.2.22.2.1.5RowStatusread-createcurrent
swL2McastFilterPortTable
OBJECT-TYPE
A table that is used to bind port to profile ID.
1.3.6.1.4.1.171.11.63.6.2.22.3not-accessiblecurrent
swL2McastFilterPortEntry
OBJECT-TYPE
A list of information that is used to bind port to profile ID.
1.3.6.1.4.1.171.11.63.6.2.22.3.1not-accessiblecurrent
swL2McastFilterPortGroupPortIndex
OBJECT-TYPE
The port index.
1.3.6.1.4.1.171.11.63.6.2.22.3.1.1INTEGERread-onlycurrent
swL2McastFilterPortProfileAddOrDelState
OBJECT-TYPE
The control multicast filter profile.
1.3.6.1.4.1.171.11.63.6.2.22.3.1.2INTEGER {none(1), add(2), delete(3)}read-writecurrent
swL2McastFilterPortProfileID
OBJECT-TYPE
This object indicates the profile ID of this entry. When read, it is always 0. When set, 0 can not be set.
1.3.6.1.4.1.171.11.63.6.2.22.3.1.3INTEGER (0..24)read-writecurrent
swL2McastFilterPortMaxGroupTable
OBJECT-TYPE
A table that contains information about the max group number based on port.
1.3.6.1.4.1.171.11.63.6.2.22.4not-accessiblecurrent
swL2McastFilterPortMaxGroupEntry
OBJECT-TYPE
A list of max group number information for each port.
1.3.6.1.4.1.171.11.63.6.2.22.4.1not-accessiblecurrent
swL2McastFilterPortMaxGroupPortIndex
OBJECT-TYPE
The port index.
1.3.6.1.4.1.171.11.63.6.2.22.4.1.1INTEGERread-onlycurrent
swL2McastFilterPortMaxGroup
OBJECT-TYPE
The max group numbers. The default is 256.
1.3.6.1.4.1.171.11.63.6.2.22.4.1.2INTEGER (1..256)read-writecurrent
swL2McastFilterPortInfoTable
OBJECT-TYPE
A table that contains information about all of the multicast groups for the ports.
1.3.6.1.4.1.171.11.63.6.2.22.5not-accessiblecurrent
swL2McastFilterPortInfoEntry
OBJECT-TYPE
A list of information about all of the multicast groups for each port.
1.3.6.1.4.1.171.11.63.6.2.22.5.1not-accessiblecurrent
swL2McastFilterPortInfoPortIndex
OBJECT-TYPE
The port index.
1.3.6.1.4.1.171.11.63.6.2.22.5.1.1INTEGERread-onlycurrent
swL2McastFilterPortInfoProfileName
OBJECT-TYPE
The multicast filter address profile Name.
1.3.6.1.4.1.171.11.63.6.2.22.5.1.2DisplayStringread-onlycurrent
swL2VlanMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.23
swL2VlanAdvertisementTable
OBJECT-TYPE
A table containing the advertisement state for each VLAN configured into the device by (local or network) management.
1.3.6.1.4.1.171.11.63.6.2.23.1not-accessiblecurrent
swL2VlanAdvertisementEntry
OBJECT-TYPE
The advertisement state for each VLAN configured into the device.
1.3.6.1.4.1.171.11.63.6.2.23.1.1not-accessiblecurrent
swL2VlanIndex
OBJECT-TYPE
The VLAN-ID or other identifier referring to this VLAN.
1.3.6.1.4.1.171.11.63.6.2.23.1.1.1INTEGER (1..4094)read-onlycurrent
swL2VlanName
OBJECT-TYPE
An administratively assigned string, which may be used to identify the VLAN.
1.3.6.1.4.1.171.11.63.6.2.23.1.1.2DisplayString (SIZE(0..32))read-onlycurrent
swL2VlanAdvertiseState
OBJECT-TYPE
This object indicates the advertise status of this VLAN entry.
1.3.6.1.4.1.171.11.63.6.2.23.1.1.3INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2VlanMultiplyMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.23.2
swL2VlanMultiplyVlanList
OBJECT-TYPE
This object specifies the VLAN ID List.
1.3.6.1.4.1.171.11.63.6.2.23.2.1DisplayString (SIZE(0..255))read-writecurrent
swL2VlanMultiplyAdvertisement
OBJECT-TYPE
This object specifies the advertisement state.
1.3.6.1.4.1.171.11.63.6.2.23.2.2INTEGER {other(1), enabled(2), disabled(3)}read-writecurrent
swL2VlanMultiplyPortList
OBJECT-TYPE
Specifies the port list.
1.3.6.1.4.1.171.11.63.6.2.23.2.3PortListread-writecurrent
swL2VlanMultiplyPortListAction
OBJECT-TYPE
Specifies the action for the port list which specified by swL2VlanMultiplyPortList.
1.3.6.1.4.1.171.11.63.6.2.23.2.4INTEGER {other(1), add-tagged(2), add-untagged(3), add-forbidden(4), delete(5)}read-writecurrent
swL2VlanMultiplyAction
OBJECT-TYPE
Specifies the action for VLANs. other: no action. create: the VLANs specified by swL2VlanMultiplyVlanList would be created at a time. configure: the VLANs specified by swL2VlanMultiplyVlanList would be configured at a time. delete: the VLANs specified by swL2VlanMultiplyVlanList would be deleted at a time.
1.3.6.1.4.1.171.11.63.6.2.23.2.5INTEGER {other(1), create(2), configure(3), delete(4)}read-writecurrent
swL2DhcpLocalRelayMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.11.63.6.2.24
swL2DhcpLocalRelayState
OBJECT-TYPE
This object indicates the status of the DHCP local relay function of the switch.
1.3.6.1.4.1.171.11.63.6.2.24.1INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent
swL2DhcpLocalRelayVLANTable
OBJECT-TYPE
This table is used to manage the DHCP local relay status for each VLAN.
1.3.6.1.4.1.171.11.63.6.2.24.2not-accessiblecurrent
swL2DhcpLocalRelayVLANEntry
OBJECT-TYPE
This object lists the current VLANs in the switch and their corresponding DHCP local relay status.
1.3.6.1.4.1.171.11.63.6.2.24.2.1not-accessiblecurrent
swL2DhcpLocalRelayVLANID
OBJECT-TYPE
This object shows the VIDs of the current VLANS in the switch.
1.3.6.1.4.1.171.11.63.6.2.24.2.1.1INTEGER (1..4094)read-onlycurrent
swL2DhcpLocalRelayVLANState
OBJECT-TYPE
This object indicates the status of the DHCP relay function of the VLAN.
1.3.6.1.4.1.171.11.63.6.2.24.2.1.2INTEGER {other(1), disabled(2), enabled(3)}read-writecurrent

Notifications

NameOIDStatus
swL2PortSecurityViolationTrap
NOTIFICATION-TYPE
When the port_security trap is enabled, if there's a new MAC that violates the pre-defined port security configuration, a trap will be sent out.
1.3.6.1.4.1.171.11.63.6.2.20.0.1current
swL2macNotification
NOTIFICATION-TYPE
This trap indicates the MAC address variations in the address table.
1.3.6.1.4.1.171.11.63.6.2.20.0.2current