MIBs Depot

DES-1228P-MIB

Registered at
1.3.6.1.4.1.171.10.75.3
Namespace
dlink
Source file
DES-1228P-MIB
Digest
sha256:74109ab190bed28b844946d2636e4b46eed872b698554a3f44f97fdc5d3cdc30

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso, mib-2
SNMPv2-TCDisplayString, PhysAddress, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DES-1228P-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
MacAddress
type
OwnerString
type
PortList
TEXTUAL-CONVENTION
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
current
RowStatus
TEXTUAL-CONVENTION
current

Objects

NameOIDSyntaxAccessStatus
des_1228pa1
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3
companyCommGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.1
commSetTable
OBJECT-TYPE
A list of SNMP Set Community Entries.
1.3.6.1.4.1.171.10.75.3.1.1not-accessiblemandatory
commSetEntry
OBJECT-TYPE
A list of SNMP Set Community properties.
1.3.6.1.4.1.171.10.75.3.1.1.1not-accessiblemandatory
commSetIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
1.3.6.1.4.1.171.10.75.3.1.1.1.1INTEGER (1..2)read-onlymandatory
commSetName
OBJECT-TYPE
The name of this SNMP Set Community Entry.
1.3.6.1.4.1.171.10.75.3.1.1.1.2DisplayString (SIZE(0..20))read-writemandatory
commSetStatus
OBJECT-TYPE
The RowStatus for the Set Community entry.
1.3.6.1.4.1.171.10.75.3.1.1.1.3RowStatusread-writemandatory
commGetTable
OBJECT-TYPE
A list of SNMP Get Community Entries.
1.3.6.1.4.1.171.10.75.3.1.2not-accessiblemandatory
commGetEntry
OBJECT-TYPE
A list of SNMP Get Community properties.
1.3.6.1.4.1.171.10.75.3.1.2.1not-accessiblemandatory
commGetIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
1.3.6.1.4.1.171.10.75.3.1.2.1.1INTEGER (1..2)read-onlymandatory
commGetName
OBJECT-TYPE
The name of this SNMP Get Community Entry.
1.3.6.1.4.1.171.10.75.3.1.2.1.2DisplayString (SIZE(0..20))read-writemandatory
commGetStatus
OBJECT-TYPE
The RowStatus for the Get Community entry.
1.3.6.1.4.1.171.10.75.3.1.2.1.3RowStatusread-writemandatory
commTrapTable
OBJECT-TYPE
A list of SNMP Trap Community Entries.
1.3.6.1.4.1.171.10.75.3.1.3not-accessiblemandatory
commTrapEntry
OBJECT-TYPE
A list of SNMP Trap Community properties.
1.3.6.1.4.1.171.10.75.3.1.3.1not-accessiblemandatory
commTrapIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported.
1.3.6.1.4.1.171.10.75.3.1.3.1.1INTEGER (1..2)read-onlymandatory
commTrapName
OBJECT-TYPE
The name of this SNMP Trap Community Entry.
1.3.6.1.4.1.171.10.75.3.1.3.1.2DisplayString (SIZE(0..20))read-writemandatory
commTrapIpAddress
OBJECT-TYPE
The IP Address of this SNMP Trap Community Entry.
1.3.6.1.4.1.171.10.75.3.1.3.1.3IpAddressread-writemandatory
commTrapSNMPBootup
OBJECT-TYPE
Bootup trap
1.3.6.1.4.1.171.10.75.3.1.3.1.5INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapSNMPTPLinkUpDown
OBJECT-TYPE
Twisted Pair link up / link down trap.
1.3.6.1.4.1.171.10.75.3.1.3.1.6INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapSNMPFiberLinkUpDown
OBJECT-TYPE
Fiber link up / link down trap.
1.3.6.1.4.1.171.10.75.3.1.3.1.7INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapTrapAbnormalTPRXError
OBJECT-TYPE
Twisted Pair abnormal receive error trap.
1.3.6.1.4.1.171.10.75.3.1.3.1.9INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapTrapAbnormalTPTXError
OBJECT-TYPE
Twisted Pair abnormal transmit error trap.
1.3.6.1.4.1.171.10.75.3.1.3.1.10INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapTrapAbnormalFiberRXError
OBJECT-TYPE
Fiber abnormal receive error trap.
1.3.6.1.4.1.171.10.75.3.1.3.1.11INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapTrapAbnormalFiberTXError
OBJECT-TYPE
Fiber abnormal transmit error trap.
1.3.6.1.4.1.171.10.75.3.1.3.1.12INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapTrapPOEPowerFail
OBJECT-TYPE
PoE POWER Fail
1.3.6.1.4.1.171.10.75.3.1.3.1.13INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapTrapPOEPortOvercurrent
OBJECT-TYPE
PoE port Overcurrent
1.3.6.1.4.1.171.10.75.3.1.3.1.14INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapTrapPOEPortShort
OBJECT-TYPE
PoE port Shortcircuit
1.3.6.1.4.1.171.10.75.3.1.3.1.15INTEGER {enabled(1), disabled(2)}read-writemandatory
commTrapStatus
OBJECT-TYPE
The RowStatus for the Trap Community entry.
1.3.6.1.4.1.171.10.75.3.1.3.1.16RowStatusread-writemandatory
companyMiscGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.3
miscReset
OBJECT-TYPE
Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing.
1.3.6.1.4.1.171.10.75.3.3.2INTEGER {reset(1), noop(2)}read-writemandatory
miscStatisticsReset
OBJECT-TYPE
Resets the units statistics. A (1) resets the unit, a (2) does nothing.
1.3.6.1.4.1.171.10.75.3.3.3INTEGER {reset(1), noop(2)}read-writemandatory
companySpanGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.4
spanOnOff
OBJECT-TYPE
Enable/Disable Spanning Tree. A (1) enables, a (2) disables.
1.3.6.1.4.1.171.10.75.3.4.1INTEGER {enabled(1), disabled(2)}read-writemandatory
companyConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.11
configVerSwPrimary
OBJECT-TYPE
The software image version string.
1.3.6.1.4.1.171.10.75.3.11.1DisplayString (SIZE(0..31))read-onlymandatory
configVerHwChipSet
OBJECT-TYPE
The hardware chipset version string.
1.3.6.1.4.1.171.10.75.3.11.2DisplayString (SIZE(0..31))read-onlymandatory
configBootTftpOperation
OBJECT-TYPE
The tftp operation to perform downloading the boot image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName.
1.3.6.1.4.1.171.10.75.3.11.3INTEGER {download(1), upload(2)}read-writemandatory
configBootTftpServerIp
OBJECT-TYPE
The TFTP server's IP address used for downloading the boot image.
1.3.6.1.4.1.171.10.75.3.11.4IpAddressread-writemandatory
configBootImageFileName
OBJECT-TYPE
The filename of the boot image to download.
1.3.6.1.4.1.171.10.75.3.11.5DisplayString (SIZE(0..63))read-writemandatory
configPortTable
OBJECT-TYPE
A list of interface entries used for enterprise specific configuration. The number of entries is given by the value of ifNumber. All interface entries are assumed to be Ethernet interafaces.
1.3.6.1.4.1.171.10.75.3.11.6not-accessiblemandatory
configPortEntry
OBJECT-TYPE
An enterprise specific interface entry.
1.3.6.1.4.1.171.10.75.3.11.6.1not-accessiblemandatory
configPort
OBJECT-TYPE
A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber.
1.3.6.1.4.1.171.10.75.3.11.6.1.1INTEGERread-onlymandatory
configPortSpeed
OBJECT-TYPE
The port's speed desired state.
1.3.6.1.4.1.171.10.75.3.11.6.1.2INTEGER {disable(1), auto(2), rate10M-Half(3), rate10M-Full(4), rate100M-Half(5), rate100M-Full(6), rate1000M-Full(7)}read-writemandatory
configPortOperStatus
OBJECT-TYPE
The port's operating speed state.
1.3.6.1.4.1.171.10.75.3.11.6.1.3INTEGER {down(1), rate10M-Half(2), rate10M-Full(3), rate100M-Half(4), rate100M-Full(5), rate1000M-Full(6)}read-onlymandatory
configVLANMode
OBJECT-TYPE
Determines the VLAN mode.
1.3.6.1.4.1.171.10.75.3.11.7INTEGER {modeTagBased(1)}read-writemandatory
configMirrorTable
OBJECT-TYPE
A list of the Mirror
1.3.6.1.4.1.171.10.75.3.11.8not-accessiblemandatory
configMirrorEntry
OBJECT-TYPE
A Mirror entry containing the Mirror id and mode.
1.3.6.1.4.1.171.10.75.3.11.8.1not-accessiblemandatory
configMirrorId
OBJECT-TYPE
An index that uniquely identifies an entry in the Mirror Table. One entries are currently supported.
1.3.6.1.4.1.171.10.75.3.11.8.1.1INTEGER (1)read-onlymandatory
configMirrorMon
OBJECT-TYPE
When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring monitoring port. This value has a valid range of 1 to ifNumber when enabled.
1.3.6.1.4.1.171.10.75.3.11.8.1.2INTEGERread-writemandatory
configMirrorTXSrc
OBJECT-TYPE
When mirroring is enabled , this identifies the TX mirroring source port.This value has a valid range of 1 to ifNumber when enbaled.Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc.Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
1.3.6.1.4.1.171.10.75.3.11.8.1.3PortListread-writemandatory
configMirrorRXSrc
OBJECT-TYPE
When mirroring is enabled , this identifies the RX mirroring source port.This value has a valid range of 1 to ifNumber when enbaled.Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc.Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
1.3.6.1.4.1.171.10.75.3.11.8.1.4PortListread-writemandatory
configMirrorStatus
OBJECT-TYPE
The RowStatus for the Mirror entry.
1.3.6.1.4.1.171.10.75.3.11.8.1.5RowStatusread-writemandatory
configSNMPEnable
OBJECT-TYPE
Enable/Disable SNMP function. A (1) enables, a (2) disables.
1.3.6.1.4.1.171.10.75.3.11.9INTEGER {enabled(1), disabled(2)}read-writemandatory
configIpAssignmentMode
OBJECT-TYPE
Indicates whether the device address is assigned by the user (manual), or DHCP, or Others(BootP).
1.3.6.1.4.1.171.10.75.3.11.12INTEGER {manual(1), dhcp(2), other(3)}read-writemandatory
configPhysAddress
OBJECT-TYPE
The interface's address at the protocol layer immediately 'below' the network layer in the protocol stack. This is the physical address for the end-station.
1.3.6.1.4.1.171.10.75.3.11.13MacAddressread-onlymandatory
configPasswordAdmin
OBJECT-TYPE
The adminstrator password
1.3.6.1.4.1.171.10.75.3.11.15DisplayString (SIZE(0..20))write-onlymandatory
configIpAddress
OBJECT-TYPE
The IP Address for the RDU box.
1.3.6.1.4.1.171.10.75.3.11.16IpAddressread-writemandatory
configNetMask
OBJECT-TYPE
The network mask for the RDU box.
1.3.6.1.4.1.171.10.75.3.11.17IpAddressread-writemandatory
configGateway
OBJECT-TYPE
The Gatway Address for the unit.
1.3.6.1.4.1.171.10.75.3.11.18IpAddressread-writemandatory
configSave
OBJECT-TYPE
Physically saves the current configuration to nvram. - use with care. (1) saves the configuration (2) does nothing.
1.3.6.1.4.1.171.10.75.3.11.19INTEGER {save(1), noop(2)}read-writemandatory
configRestoreDefaults
OBJECT-TYPE
Restores the configuration of the unit to the original settings.
1.3.6.1.4.1.171.10.75.3.11.22INTEGER {restore(1), noop(2)}read-writemandatory
configTftpServerIpAddress
OBJECT-TYPE
The TFTP server's IP address used to upload or download configuration file.
1.3.6.1.4.1.171.10.75.3.11.32IpAddressread-writemandatory
configTftpServerFileName
OBJECT-TYPE
The filename used to store or retrieve the configuration file from the tftp server.
1.3.6.1.4.1.171.10.75.3.11.33DisplayString (SIZE(0..64))read-writemandatory
configTftpOperation
OBJECT-TYPE
The tftp operation to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName.
1.3.6.1.4.1.171.10.75.3.11.34INTEGER {download(1), upload(2)}read-writemandatory
configSafeguardEnable
OBJECT-TYPE
Enable/Disable Safeguard Engine. D-Link Safeguard Engine is a robust and innovative technology developed by D-Link, which will automatically throttle the impact of packet flooding into the switch's CPU. It will keep D-Link Switches better protected from being too frequently interrupted by malicious viruses or worm attacks.
1.3.6.1.4.1.171.10.75.3.11.44INTEGER {enabled(1), disabled(2)}read-writemandatory
companyTVlanGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.13
tvlanTable
OBJECT-TYPE
A list of the VLANs
1.3.6.1.4.1.171.10.75.3.13.1not-accessiblemandatory
tvlanEntry
OBJECT-TYPE
A VLAN entry containing the VLAN id and name.
1.3.6.1.4.1.171.10.75.3.13.1.1not-accessiblemandatory
tvlanId
OBJECT-TYPE
The VLAN identifier. A maximum of 256 VLANs is supported. The value must be from 1 to 4094.
1.3.6.1.4.1.171.10.75.3.13.1.1.1INTEGERread-onlymandatory
tvlanName
OBJECT-TYPE
The VLAN name.Length must between 1 and 20.
1.3.6.1.4.1.171.10.75.3.13.1.1.2DisplayStringread-writemandatory
tvlanMember
OBJECT-TYPE
The set of the device's member ports that belong to the VLAN. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the VLAN is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
1.3.6.1.4.1.171.10.75.3.13.1.1.3PortListread-writemandatory
tvlanUntaggedPorts
OBJECT-TYPE
If that bit has a value of '1' the outgoing frame on the egress port is untagged. If that bit has a value of '0' the outgoing frame on the egress port is tagged.
1.3.6.1.4.1.171.10.75.3.13.1.1.4PortListread-writemandatory
tvlanStatus
OBJECT-TYPE
The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.3.13.1.1.5INTEGER {active(1), notready(3), createAndwait(5), destroy(6)}read-writemandatory
tvlanManagementOnOff
OBJECT-TYPE
Enable/Disable management VLAN mechanism.
1.3.6.1.4.1.171.10.75.3.13.2INTEGER {enabled(1), disabled(2)}read-writemandatory
tvlanManagementid
OBJECT-TYPE
The management VLAN ID which allow to forward to CPU.
1.3.6.1.4.1.171.10.75.3.13.3INTEGERread-writemandatory
tvlanPortTable
OBJECT-TYPE
A list of ports and their associated VLAN.
1.3.6.1.4.1.171.10.75.3.13.4not-accessiblemandatory
tvlanPortEntry
OBJECT-TYPE
Information pertaining to an individual port regarding to which VLAN it belongs.
1.3.6.1.4.1.171.10.75.3.13.4.1not-accessiblemandatory
tvlanPortPortId
OBJECT-TYPE
A port identifier that is in the range of 1 to ifNumber.
1.3.6.1.4.1.171.10.75.3.13.4.1.1INTEGERread-onlymandatory
tvlanPortVlanId
OBJECT-TYPE
The default VLAN identifier, PVID. The value must be from 1 to 4094.
1.3.6.1.4.1.171.10.75.3.13.4.1.2INTEGERread-writemandatory
tvlanAsyOnOff
OBJECT-TYPE
Enable/Disable IEEE 802.1Q Asymmetric VLAN
1.3.6.1.4.1.171.10.75.3.13.5INTEGER {enabled(1), disabled(2)}read-writemandatory
companyPortTrunkGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.14
portTrunkTable
OBJECT-TYPE
A list of port trunks and their associated members.
1.3.6.1.4.1.171.10.75.3.14.1not-accessiblemandatory
portTrunkEntry
OBJECT-TYPE
A port trunk entry containing the trunk id and trunk members.
1.3.6.1.4.1.171.10.75.3.14.1.1not-accessiblemandatory
portTrunkId
OBJECT-TYPE
The port trunk identifier. The current range is from 1 to 6.
1.3.6.1.4.1.171.10.75.3.14.1.1.1INTEGERread-onlymandatory
portTrunkName
OBJECT-TYPE
The Trunk name.Length must between 1 and 20.
1.3.6.1.4.1.171.10.75.3.14.1.1.2DisplayStringread-writemandatory
portTrunkMember
OBJECT-TYPE
A port trunk member value indicates which port is a member of the specified trunk. Valid values are in the range from 0 to ifNumber. A zero indicates that no port is contained in the specifed member. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
1.3.6.1.4.1.171.10.75.3.14.1.1.3PortListread-writemandatory
companyPoEGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.15
poePortTable
OBJECT-TYPE
A list of SNMP Set POE Port Entries.
1.3.6.1.4.1.171.10.75.3.15.1not-accessiblemandatory
poePortEntry
OBJECT-TYPE
A list of SNMP Set POE Port properties.
1.3.6.1.4.1.171.10.75.3.15.1.1not-accessiblemandatory
poeportgroup
OBJECT-TYPE
POE Port Group Index.
1.3.6.1.4.1.171.10.75.3.15.1.1.1INTEGERread-onlymandatory
poeportid
OBJECT-TYPE
POE Port ID Index.
1.3.6.1.4.1.171.10.75.3.15.1.1.2INTEGERread-onlymandatory
poeportpowerlimit
OBJECT-TYPE
The value of POE Port Power Limit.
1.3.6.1.4.1.171.10.75.3.15.1.1.3INTEGER {auto(0), class1(1), class2(2), class3(3)}read-writemandatory
companyStaticGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.21
staticOnOff
OBJECT-TYPE
Enable/Disable Static MAC. Currently it doesn't support 'disabled' function.
1.3.6.1.4.1.171.10.75.3.21.1INTEGER {enabled(1), disabled(2)}read-writemandatory
staticAutoLearning
OBJECT-TYPE
The set of the device's member ports that belong to the Static MAC auto learning enable/disable. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is in auto learning enable state; the port is not in auto learning state if its bit has a value of '0'.
1.3.6.1.4.1.171.10.75.3.21.2PortListread-writemandatory
staticTable
OBJECT-TYPE
A list of the Static MACs
1.3.6.1.4.1.171.10.75.3.21.3not-accessiblemandatory
staticEntry
OBJECT-TYPE
A Static MAC entry containing the mac and forwarding port.
1.3.6.1.4.1.171.10.75.3.21.3.1not-accessiblemandatory
staticId
OBJECT-TYPE
The Static MAC identifier. A maximum of 60 Static MACs is supported. The value must be from 1 to 60
1.3.6.1.4.1.171.10.75.3.21.3.1.1INTEGERread-onlymandatory
staticMac
OBJECT-TYPE
The Static MAC associated with the Id.
1.3.6.1.4.1.171.10.75.3.21.3.1.2MacAddressread-writemandatory
staticPort
OBJECT-TYPE
The Static MAC forwarding port with the ID.
1.3.6.1.4.1.171.10.75.3.21.3.1.3INTEGERread-writemandatory
staticVlanID
OBJECT-TYPE
The Static MAC VLAN ID with the ID.
1.3.6.1.4.1.171.10.75.3.21.3.1.4INTEGERread-writemandatory
staticStatus
OBJECT-TYPE
The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.3.21.3.1.5INTEGER {active(1), notready(3), createAndwait(5), destroy(6)}read-writemandatory
companyIgsGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.22
igsSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.22.1
igsStatus
OBJECT-TYPE
Enables or disables IGMP snooping in the system.
1.3.6.1.4.1.171.10.75.3.22.1.2INTEGER {enabled(1), disabled(2)}read-writemandatory
igsv3Processing
OBJECT-TYPE
To enable processing of IGMPv3 messages and to operate in IGMPv3 mode, this object must be set to enabled, when set as disabled the operation will be in IGMPv2 mode.
1.3.6.1.4.1.171.10.75.3.22.1.3INTEGER {enabled(1), disabled(2)}read-onlymandatory
igsRouterPortPurgeInterval
OBJECT-TYPE
This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, a 'RouterPortPurgeTimer' runs for 'RouterPortPurgeInterval'. This timer will be restarted whenever a router control message is received over that port. If no router control mssages are received for 'RouterPortPurgeInterval' time, the learnt router port entry will be purged.
1.3.6.1.4.1.171.10.75.3.22.1.4INTEGER (60..600)read-writemandatory
igsHostPortPurgeInterval
OBJECT-TYPE
This is the interval (in seconds) after which a learnt host port entry will be purged. For each host port learnt, a 'PortPurgeTimer' runs for 'HostPortPurgeInterval'. This timer will be restarted whenever a report message from host is received over that port. If no report mssages are received for 'HostPortPurgeInterval' time, the learnt host entry will be purged from the multicast group.
1.3.6.1.4.1.171.10.75.3.22.1.5INTEGER (130..153025)read-onlymandatory
igsReportForwardInterval
OBJECT-TYPE
This is the interval (in seconds) within which the next report messages for the same multicast group will not be forwarded out. The purpose of this timer is to avoid multiple report messages for the same group being forwarded out. So that unnecessary multicast packets in the network can be avoided. The 'ReportForwardTimer' is per multicast group. This timer is started as soon as a report message for that group is forwarded out. Within this 'ReportForwardInterval' if another report for the same group arrives, that report will not be forwarded. The first report message which is received for this group after the 'ReportForwardInterval' only will be forwarded out. When set as '0' , this timer will not be started and all the report messages will be forwarded as and when they are received.
1.3.6.1.4.1.171.10.75.3.22.1.6INTEGER (0..25)read-onlymandatory
igsLeaveProcessInterval
OBJECT-TYPE
This is the interval (in seconds) after which a Leave message is forwarded on either router port(if present) or on all ports of a bridge (if no router port present). when a leave message from a host for a group is received by the bridge, The bridge will form a group-specific query and sends it on the port on which the leave message is received. A timer is started by a bridge with a time interval equal to IgsLeaveProcessInterval. If a report message is received before above timer expires, Leave message is dropped.Otherwise Leave message is either forwarded on all ports of the bridge or only on router port depending upon the case.
1.3.6.1.4.1.171.10.75.3.22.1.7INTEGER (0..25)read-writemandatory
igsMcastEntryAgeingInterval
OBJECT-TYPE
This is the interval (in seconds) after which the target will be checked for Multicast data hit for the entry This timer will be started for every (S, G) in the control plane.
1.3.6.1.4.1.171.10.75.3.22.1.8INTEGER (60..600)read-onlymandatory
igsSharedSegmentAggregationInterval
OBJECT-TYPE
This is the interval (in seconds) for which reports of IGMPv3 messages on a shared segment will be aggregated for a group. This timer will be started only when multiple hosts are identified on a port for the Multicast group. The timer will be stopped when all but one host is left on the port for the Multicast group. This timer will be re-started on its expiry and Multicast forwarding table will be updated.
1.3.6.1.4.1.171.10.75.3.22.1.9INTEGER (0..60)read-onlymandatory
igsGblReportFwdOnAllPorts
OBJECT-TYPE
IGMP snooping module will forward reports only on router ports by default, to enable forwarding on all other ports the object must be set to allports.
1.3.6.1.4.1.171.10.75.3.22.1.10INTEGER {allports(1), rtrports(2)}read-onlymandatory
igsNextMcastFwdMode
OBJECT-TYPE
This field describes the multicast forwarding mode that will be used upon restart of the ISS Switch.
1.3.6.1.4.1.171.10.75.3.22.1.13INTEGER {ipbased(1), macbased(2)}read-onlymandatory
igsQueryInterval
OBJECT-TYPE
The frequency at which IGMP Host-Query packets are transmitted on this interface.
1.3.6.1.4.1.171.10.75.3.22.1.14INTEGER (60..600)read-writemandatory
igsQueryMaxResponseTime
OBJECT-TYPE
The maximum query response time advertised in IGMPv2 queries on this interface.
1.3.6.1.4.1.171.10.75.3.22.1.15INTEGER (10..25)read-writemandatory
igsRobustnessValue
OBJECT-TYPE
The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.
1.3.6.1.4.1.171.10.75.3.22.1.16INTEGER (2..255)read-writemandatory
igsLastMembQueryInterval
OBJECT-TYPE
The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages. This value may be tuned to modify the leave latency of the network. A reduced value results in reduced time to detect the loss of the last member of a group. The value of this object is irrelevant if igmpInterfaceVersion is 1.
1.3.6.1.4.1.171.10.75.3.22.1.17INTEGER (1..25)read-writemandatory
igsQuerierStateOnOff
OBJECT-TYPE
To enable transmitting IGMP Query packets or to disable.
1.3.6.1.4.1.171.10.75.3.22.1.18INTEGER {enabled(1), disabled(2)}read-writemandatory
igsVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.22.3
igsVlanMcastFwdTable
OBJECT-TYPE
This table contains VLAN based multicast forwarding information learnt when VLAN is ENABLED in the system.
1.3.6.1.4.1.171.10.75.3.22.3.1not-accessiblemandatory
igsVlanMcastFwdEntry
OBJECT-TYPE
This table contains VlanId, multicast group address and the list of ports who have members for the multicast group.
1.3.6.1.4.1.171.10.75.3.22.3.1.1not-accessiblemandatory
igsVlanMcastFwdVlanIdMac
OBJECT-TYPE
Vlan Id pertaining to the Multicast forwarding entry.
1.3.6.1.4.1.171.10.75.3.22.3.1.1.1INTEGER (1..4094)not-accessiblemandatory
igsVlanMcastFwdGroupAddress
OBJECT-TYPE
MAC multicast group address.
1.3.6.1.4.1.171.10.75.3.22.3.1.1.2MacAddressnot-accessiblemandatory
igsVlanMcastFwdPortListMac
OBJECT-TYPE
List of ports who have members for the MAC multicast group and the Vlan Id.
1.3.6.1.4.1.171.10.75.3.22.3.1.1.3PortListread-onlymandatory
igsVlanRouterPortListTable
OBJECT-TYPE
This table contains list of bridge ports through which a router, in a particular VLAN, is reachable.
1.3.6.1.4.1.171.10.75.3.22.3.3not-accessiblemandatory
igsVlanRouterPortListEntry
OBJECT-TYPE
Contains VlanId of router , list of reachable router ports.
1.3.6.1.4.1.171.10.75.3.22.3.3.1not-accessiblemandatory
igsVlanRouterPortListVlanId
OBJECT-TYPE
Vlan Id of the ports through which router is reachable.
1.3.6.1.4.1.171.10.75.3.22.3.3.1.1INTEGER (1..4094)not-accessiblemandatory
igsVlanRouterPortList
OBJECT-TYPE
Contains list of bridge ports through which a router, in a particular VLAN, is reachable. These router ports are learnt through control messages received from routers, and can also be configured statically.
1.3.6.1.4.1.171.10.75.3.22.3.3.1.2PortListread-onlymandatory
igsVlanFilterTable
OBJECT-TYPE
This table contains configuration to disable IGMP snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.
1.3.6.1.4.1.171.10.75.3.22.3.4not-accessiblemandatory
igsVlanFilterEntry
OBJECT-TYPE
Contains Vlan Id , Vlan Filter Status.
1.3.6.1.4.1.171.10.75.3.22.3.4.1not-accessiblemandatory
igsVlanId
OBJECT-TYPE
Vlan Id for which IGMP snooping feature is to be disabled.
1.3.6.1.4.1.171.10.75.3.22.3.4.1.1INTEGER (1..4094)not-accessiblemandatory
igsVlanFilterStatus
OBJECT-TYPE
When status is set as enabled, IGMP snooping feature is disabled for that Vlan Id. When status is set as disabled, the entry stands invalid. In that case IGMP snooping feature remains enabled for that Vlan.
1.3.6.1.4.1.171.10.75.3.22.3.4.1.2INTEGER {enabled(1), disabled(2)}read-writemandatory
companyDot1xGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.23
radius
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.23.1
radiusServerAddress
OBJECT-TYPE
The IP address of the RADIUS server.
1.3.6.1.4.1.171.10.75.3.23.1.1IpAddressread-writemandatory
radiusServerPort
OBJECT-TYPE
The Port of the RADIUS server.
1.3.6.1.4.1.171.10.75.3.23.1.2INTEGER (1..65535)read-writemandatory
radiusServerSharedSecret
OBJECT-TYPE
The secret string which is shared between Server and Client.
1.3.6.1.4.1.171.10.75.3.23.1.3DisplayStringread-writemandatory
dot1xAuth
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.23.2
dot1xAuthSystemControl
OBJECT-TYPE
Enable/Disable Static 802.1x. A (1) enables, a (2) disables.
1.3.6.1.4.1.171.10.75.3.23.2.1INTEGER {enabled(1), disabled(2)}read-writemandatory
dot1xAuthQuietPeriod
OBJECT-TYPE
The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine.
1.3.6.1.4.1.171.10.75.3.23.2.2INTEGER (0..65535)read-writemandatory
dot1xAuthTxPeriod
OBJECT-TYPE
The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine.
1.3.6.1.4.1.171.10.75.3.23.2.3INTEGER (1..65535)read-writemandatory
dot1xAuthSuppTimeout
OBJECT-TYPE
The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.3.23.2.4INTEGER (1..65535)read-writemandatory
dot1xAuthServerTimeout
OBJECT-TYPE
The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.3.23.2.5INTEGER (1..65535)read-writemandatory
dot1xAuthMaxReq
OBJECT-TYPE
The value of the maxReq constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.3.23.2.6INTEGER (1..10)read-writemandatory
dot1xAuthReAuthPeriod
OBJECT-TYPE
The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine.
1.3.6.1.4.1.171.10.75.3.23.2.7Unsigned32 (1..4294967295)read-writemandatory
dot1xAuthReAuthEnabled
OBJECT-TYPE
The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1).
1.3.6.1.4.1.171.10.75.3.23.2.8INTEGER {enabled(1), disabled(2)}read-writemandatory
dot1xAuthConfigPortTable
OBJECT-TYPE
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
1.3.6.1.4.1.171.10.75.3.23.2.9not-accessiblemandatory
dot1xAuthConfigPortEntry
OBJECT-TYPE
The configuration information for an Authenticator Port.
1.3.6.1.4.1.171.10.75.3.23.2.9.1not-accessiblemandatory
dot1xAuthConfigPortNumber
OBJECT-TYPE
A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber.
1.3.6.1.4.1.171.10.75.3.23.2.9.1.1INTEGERread-onlymandatory
dot1xAuthConfigPortControl
OBJECT-TYPE
The current value of the controlled Port control parameter for the Port.
1.3.6.1.4.1.171.10.75.3.23.2.9.1.2INTEGER {enabled(1), disabled(2)}read-writemandatory
dot1xAuthConfigPortStatus
OBJECT-TYPE
The current value of the controlled Port status parameter for the Port.
1.3.6.1.4.1.171.10.75.3.23.2.9.1.3INTEGER {authnull(0), authorized(1), unauthorized(2)}read-onlymandatory
dot1xAuthConfigPortSessionTime
OBJECT-TYPE
The duration of the session in seconds.
1.3.6.1.4.1.171.10.75.3.23.2.9.1.4TimeTicksread-onlymandatory
dot1xAuthConfigPortSessionUserName
OBJECT-TYPE
The User-Name representing the identity of the Supplicant PAE.
1.3.6.1.4.1.171.10.75.3.23.2.9.1.5DisplayStringread-onlymandatory
companyLLDPExtnGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.24
lldpSysMACDigest
OBJECT-TYPE
The system MAC Digest
1.3.6.1.4.1.171.10.75.3.24.1DisplayString (SIZE(32))read-onlymandatory
lldpAntiRoguePortControl
OBJECT-TYPE
When LLDP anti-rogue port control is enabled , this identifies the port control status of each port. This value has a valid range of 1 to ifNumber when enbaled. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
1.3.6.1.4.1.171.10.75.3.24.2PortListread-writemandatory
lldpRemOrgDefInfoTable
OBJECT-TYPE
This table contains one or more rows per physical network connection which advertises the organizationally defined information. Note that this table contains one or more rows of organizationally defined information that is not recognized by the local agent. If the local system is capable of recognizing any organizationally defined information, appropriate extension MIBs from the organization should be used for information retrieval.
1.3.6.1.4.1.171.10.75.3.24.3not-accessiblemandatory
lldpRemOrgDefInfoEntry
OBJECT-TYPE
Information about the unrecognized organizationally defined information advertised by the remote system. The lldpAntiRoguePortIndex is index to this table. Entries may be created and deleted in this table by the agent.
1.3.6.1.4.1.171.10.75.3.24.3.1not-accessiblemandatory
lldpAntiRoguePortIndex
OBJECT-TYPE
A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber.
1.3.6.1.4.1.171.10.75.3.24.3.1.1INTEGERread-onlymandatory
lldpAntiRoguePortStatus
OBJECT-TYPE
The value represents each port's authentication status. 0: Authentication disabled. 1: Authentication enabled but not passed. 2: Authentication successful.
1.3.6.1.4.1.171.10.75.3.24.3.1.2INTEGER {authentication_disabled(0), authentication_enabled(1), authentication_successful(2)}read-onlymandatory
lldpRemOrgDefInfoOUI
OBJECT-TYPE
The Organizationally Unique Identifier (OUI), as defined in IEEE std 802-2001, is a 24 bit (three octets) globally unique assigned number referenced by various standards, of the information received from the remote system.
1.3.6.1.4.1.171.10.75.3.24.3.1.3OCTET STRING (SIZE(3))read-onlymandatory
lldpAntiRogueKey
OBJECT-TYPE
The Anti Rogue Key
1.3.6.1.4.1.171.10.75.3.24.4OCTET STRING (SIZE(20))read-writemandatory
lldpSysConfigChecksum
OBJECT-TYPE
The system EEPROM config checksum. Use this value to check system config has been changed or not.
1.3.6.1.4.1.171.10.75.3.24.5INTEGERread-onlymandatory
lldpGalobalEnable
OBJECT-TYPE
Enable or disable the LLDP protocol. (1) enables the system and (2) disables it.
1.3.6.1.4.1.171.10.75.3.24.6INTEGER {enable(1), disable(2)}read-writemandatory
companyQoSGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.26
qosMode
OBJECT-TYPE
Settings of Qos mode: IEEE 802.1p QoS or DSCP QoS.
1.3.6.1.4.1.171.10.75.3.26.1INTEGER {dot1p(1), dscp(2)}read-writemandatory
queuingMechanism
OBJECT-TYPE
Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin
1.3.6.1.4.1.171.10.75.3.26.2INTEGER {strictPriority(1), wrr(2)}read-writemandatory
dot1pPortTable
OBJECT-TYPE
A list of 802.1p port default priority Entries.
1.3.6.1.4.1.171.10.75.3.26.3not-accessiblemandatory
dot1pPortEntry
OBJECT-TYPE
A list of 802.1p port default priority priorities.
1.3.6.1.4.1.171.10.75.3.26.3.1not-accessiblemandatory
dot1pPortIndex
OBJECT-TYPE
A port identifier that is in the range of 1 to ifNumber.
1.3.6.1.4.1.171.10.75.3.26.3.1.1INTEGERread-onlymandatory
dot1pPortPriority
OBJECT-TYPE
For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, D-Link Smart Switches will refer to their 802.1p information and prioritize them with 4 different priority queues.
1.3.6.1.4.1.171.10.75.3.26.3.1.2INTEGER {low(1), middle(2), high(3), highest(4)}read-writemandatory
dscpTable
OBJECT-TYPE
A list of DSCP Entries.
1.3.6.1.4.1.171.10.75.3.26.4not-accessiblemandatory
dscpEntry
OBJECT-TYPE
A list of DSCP properties.
1.3.6.1.4.1.171.10.75.3.26.4.1not-accessiblemandatory
dscpIndex
OBJECT-TYPE
DSCP value. For ingress IP packets, the DiffServ field of IP packets provide DSCP-based traffic prioritization information to switches. D-Link Smart Switches will refer to the value of DiffServ filed information and prioritize them with 4 different priority queues.
1.3.6.1.4.1.171.10.75.3.26.4.1.1INTEGER (0..63)read-onlymandatory
dscpPriority
OBJECT-TYPE
The queuing priority mapping to DSCP value.
1.3.6.1.4.1.171.10.75.3.26.4.1.2INTEGER {low(1), middle(2), high(3), highest(4)}read-writemandatory
companyTrafficMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.27
broadcastStormCtrlSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.27.3
broadcastStormCtrlGlobalOnOff
OBJECT-TYPE
This object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will allowed you to limit the number of broadcast packets per second going through device.
1.3.6.1.4.1.171.10.75.3.27.3.1INTEGER {enabled(1), disabled(2)}read-writemandatory
broadcastStormGlobalThreshold
OBJECT-TYPE
The threshold value in unit of thousand bytes per second for broadcast traffic of the specific port.
1.3.6.1.4.1.171.10.75.3.27.3.2INTEGER {disabled(1), kBps-8(2), kBps-16(3), kBps-32(4), kBps-64(5), kBps-128(6), kBps-256(7), kBps-512(8), kBps-1024(9), kBps-2048(10), kBps-4096(11)}read-writemandatory
companySecurity
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.28
trustedHostSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.3.28.1
trustedHostOnOff
OBJECT-TYPE
This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.
1.3.6.1.4.1.171.10.75.3.28.1.1INTEGER {enabled(1), disabled(2)}read-writemandatory
trustedHostTable
OBJECT-TYPE
A list of Trusted Host Entries.
1.3.6.1.4.1.171.10.75.3.28.1.2not-accessiblemandatory
trustedHostEntry
OBJECT-TYPE
A list of Trusted Host properties.
1.3.6.1.4.1.171.10.75.3.28.1.2.1not-accessiblemandatory
trustedHostID
OBJECT-TYPE
An index that uniquely identifies an entry in the Trusted Host Table. Three entries are currently supported.
1.3.6.1.4.1.171.10.75.3.28.1.2.1.1INTEGERread-onlymandatory
trustedHostIpAddress
OBJECT-TYPE
The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.
1.3.6.1.4.1.171.10.75.3.28.1.2.1.2IpAddressread-writemandatory
trustedHostIpMask
OBJECT-TYPE
Used to mask with IP address, it allow you set a subnet as a trusted host entry.
1.3.6.1.4.1.171.10.75.3.28.1.2.1.3IpAddressread-writemandatory
trustedHostStatus
OBJECT-TYPE
The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.3.28.1.2.1.4INTEGER {active(1), notready(3), createAndwait(5), destroy(6)}read-writemandatory

Notifications

NameOIDStatus
swFiberInsert
NOTIFICATION-TYPE
Fiber insert trap.
1.3.6.1.4.1.171.10.75.3.0.1
swFiberRemove
NOTIFICATION-TYPE
Fiber remove trap.
1.3.6.1.4.1.171.10.75.3.0.2
swFiberAbnormalRXError
NOTIFICATION-TYPE
Fiber abnormal rx error trap.
1.3.6.1.4.1.171.10.75.3.0.3
swFiberAbnormalTXError
NOTIFICATION-TYPE
Fiber abnormal tx error trap.
1.3.6.1.4.1.171.10.75.3.0.4
swTPAbnormalRXError
NOTIFICATION-TYPE
Twisted Pair abnormal rx error trap.
1.3.6.1.4.1.171.10.75.3.0.5
swTPAbnormalTXError
NOTIFICATION-TYPE
Twisted Pair abnormal tx error trap.
1.3.6.1.4.1.171.10.75.3.0.6