DES-1226G-MIB
- Registered at
- 1.3.6.1.4.1.171.10.75.1
- Namespace
- dlink
- Source file
DES-1226G-MIB- Digest
sha256:f68acc2041fc7e6ece49345f9161e1ab15a74a887b6cc43dcbaa738f2b911f95
Imports
| From | Symbols |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Counter32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, enterprises, iso, mib-2 |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
DES-1226G-MIB SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| MacAddress type | ||||
| OwnerString type | ||||
| PortList TEXTUAL-CONVENTION Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. | current | |||
| RowStatus TEXTUAL-CONVENTION | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| d_link OBJECT-IDENTITY | 1.3.6.1.4.1.171 | |||
| dlink_products OBJECT-IDENTITY | 1.3.6.1.4.1.171.10 | |||
| dlink_FESmartSwitch OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75 | |||
| des_1226G OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75.1 | |||
| companyCommGroup OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75.1.1 | |||
| commSetTable OBJECT-TYPE A list of SNMP Set Community Entries | 1.3.6.1.4.1.171.10.75.1.1.1 | not-accessible | mandatory | |
| commSetEntry OBJECT-TYPE A list of SNMP Set Community properties | 1.3.6.1.4.1.171.10.75.1.1.1.1 | not-accessible | mandatory | |
| commSetIndex OBJECT-TYPE An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. | 1.3.6.1.4.1.171.10.75.1.1.1.1.1 | INTEGER (1..2) | read-only | mandatory |
| commSetName OBJECT-TYPE The name of this SNMP Set Community Entry. | 1.3.6.1.4.1.171.10.75.1.1.1.1.2 | DisplayString (SIZE(0..20)) | read-write | mandatory |
| commSetStatus OBJECT-TYPE The RowStatus for the Set Community entry. | 1.3.6.1.4.1.171.10.75.1.1.1.1.3 | RowStatus | read-write | mandatory |
| commGetTable OBJECT-TYPE A list of SNMP Get Community Entries | 1.3.6.1.4.1.171.10.75.1.1.2 | not-accessible | mandatory | |
| commGetEntry OBJECT-TYPE A list of SNMP Get Community properties | 1.3.6.1.4.1.171.10.75.1.1.2.1 | not-accessible | mandatory | |
| commGetIndex OBJECT-TYPE An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. | 1.3.6.1.4.1.171.10.75.1.1.2.1.1 | INTEGER (1..2) | read-only | mandatory |
| commGetName OBJECT-TYPE The name of this SNMP Get Community Entry. | 1.3.6.1.4.1.171.10.75.1.1.2.1.2 | DisplayString (SIZE(0..20)) | read-write | mandatory |
| commGetStatus OBJECT-TYPE The RowStatus for the Get Community entry. | 1.3.6.1.4.1.171.10.75.1.1.2.1.3 | RowStatus | read-write | mandatory |
| commTrapTable OBJECT-TYPE A list of SNMP Trap Community Entries | 1.3.6.1.4.1.171.10.75.1.1.3 | not-accessible | mandatory | |
| commTrapEntry OBJECT-TYPE A list of SNMP Trap Community properties | 1.3.6.1.4.1.171.10.75.1.1.3.1 | not-accessible | mandatory | |
| commTrapIndex OBJECT-TYPE An index that uniquely identifies an entry in the Community Table. Eight entries are currently supported. | 1.3.6.1.4.1.171.10.75.1.1.3.1.1 | INTEGER (1..2) | read-only | mandatory |
| commTrapName OBJECT-TYPE The name of this SNMP Trap Community Entry. | 1.3.6.1.4.1.171.10.75.1.1.3.1.2 | DisplayString (SIZE(0..20)) | read-write | mandatory |
| commTrapIpAddress OBJECT-TYPE The IP Address of this SNMP Trap Community Entry. | 1.3.6.1.4.1.171.10.75.1.1.3.1.3 | IpAddress | read-write | mandatory |
| commTrapSNMPBootup OBJECT-TYPE Bootup trap | 1.3.6.1.4.1.171.10.75.1.1.3.1.5 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| commTrapSNMPTPLinkUpDown OBJECT-TYPE Twisted Pair link up / link down trap | 1.3.6.1.4.1.171.10.75.1.1.3.1.6 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| commTrapSNMPFiberLinkUpDown OBJECT-TYPE Fiber link up / link down trap | 1.3.6.1.4.1.171.10.75.1.1.3.1.7 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| commTrapStatus OBJECT-TYPE The RowStatus for the Trap Community entry. | 1.3.6.1.4.1.171.10.75.1.1.3.1.13 | RowStatus | read-write | mandatory |
| companyMiscGroup OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75.1.3 | |||
| miscReset OBJECT-TYPE Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing. | 1.3.6.1.4.1.171.10.75.1.3.2 | INTEGER {reset(1), noop(2)} | read-write | mandatory |
| companyConfigGroup OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75.1.11 | |||
| configVerSwPrimary OBJECT-TYPE The software image version string | 1.3.6.1.4.1.171.10.75.1.11.1 | DisplayString (SIZE(0..31)) | read-only | mandatory |
| configVerHwChipSet OBJECT-TYPE The hardware chipset version string | 1.3.6.1.4.1.171.10.75.1.11.2 | DisplayString (SIZE(0..31)) | read-only | mandatory |
| configPortTable OBJECT-TYPE A list of interface entries used for enterprise specific configuration. The number of entries is given by the value of ifNumber. All interface entries are assumed to be Ethernet interafaces. | 1.3.6.1.4.1.171.10.75.1.11.6 | not-accessible | mandatory | |
| configPortEntry OBJECT-TYPE An enterprise specific interface entry. | 1.3.6.1.4.1.171.10.75.1.11.6.1 | not-accessible | mandatory | |
| configPort OBJECT-TYPE A unique value for each interface that correlates to ifIndex. Its value ranges between 1 and the value of ifNumber. | 1.3.6.1.4.1.171.10.75.1.11.6.1.1 | INTEGER | read-only | mandatory |
| configPortSpeed OBJECT-TYPE The port's speed desired state. | 1.3.6.1.4.1.171.10.75.1.11.6.1.2 | INTEGER {disable(1), auto(2), rate10M-Half(3), rate10M-Full(4), rate100M-Half(5), rate100M-Full(6), rate1G-Full(7)} | read-write | mandatory |
| configPortOperStatus OBJECT-TYPE The port's operating speed state. | 1.3.6.1.4.1.171.10.75.1.11.6.1.3 | INTEGER {down(1), rate10M-Half(2), rate10M-Full(3), rate100M-Half(4), rate100M-Full(5), rate1G-Half(6), rate1G-Full(7)} | read-only | mandatory |
| configPortFlowControl OBJECT-TYPE The port will avoid transmitting a new packet for the period of time specified in a received PAUSE packet when enabled. | 1.3.6.1.4.1.171.10.75.1.11.6.1.4 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| configPortFlowControlOper OBJECT-TYPE The port's operating flow control state. | 1.3.6.1.4.1.171.10.75.1.11.6.1.5 | INTEGER {enabled(1), disabled(2)} | read-only | mandatory |
| configPortPriority OBJECT-TYPE The port's current priority. | 1.3.6.1.4.1.171.10.75.1.11.6.1.6 | INTEGER {qlevel0(0), qlevel1(1), qlevel2(2), qlevel3(3), qlevel4(4), qlevel5(5), qlevel6(6), qlevel7(7)} | read-write | mandatory |
| configMirrorTable OBJECT-TYPE A list of the Mirror | 1.3.6.1.4.1.171.10.75.1.11.8 | not-accessible | mandatory | |
| configMirrorEntry OBJECT-TYPE A Mirror entry containing the Mirror id and mode | 1.3.6.1.4.1.171.10.75.1.11.8.1 | not-accessible | mandatory | |
| configMirrorId OBJECT-TYPE An index that uniquely identifies an entry in the Mirror Table. One entries are currently supported. | 1.3.6.1.4.1.171.10.75.1.11.8.1.1 | INTEGER (1) | read-only | mandatory |
| configMirrorMode OBJECT-TYPE When deciding the mirroring source port, then Mirror mode will be available. | 1.3.6.1.4.1.171.10.75.1.11.8.1.2 | INTEGER {disabled(0), rx(1), tx(2), both(3)} | read-write | mandatory |
| configMirrorMon OBJECT-TYPE When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring monitoring port. This value has a valid range of 1 to ifNumber when enabled. | 1.3.6.1.4.1.171.10.75.1.11.8.1.3 | INTEGER | read-write | mandatory |
| configMirrorSrc OBJECT-TYPE When mirroring is enabled (configMirroringMode = ingress, egress, both), this identifies the mirroring source port. This value has a valid range of 1 to ifNumber when enbaled. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. | 1.3.6.1.4.1.171.10.75.1.11.8.1.4 | PortList | read-write | mandatory |
| configMirrorStatus OBJECT-TYPE The RowStatus for the Mirror entry. | 1.3.6.1.4.1.171.10.75.1.11.8.1.5 | RowStatus | read-write | mandatory |
| configSNMPEnable OBJECT-TYPE Enable/Disable SNMP function. A (1) enables, a (2) disables. | 1.3.6.1.4.1.171.10.75.1.11.9 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| configIpAssignmentMode OBJECT-TYPE Indicates whether the device address is assigned by the user (manual), or DHCP, or Others(BootP). | 1.3.6.1.4.1.171.10.75.1.11.12 | INTEGER {manual(1), dhcp(2), other(3)} | read-write | mandatory |
| configPhysAddress OBJECT-TYPE The interface's address at the protocol layer immediately 'below' the network layer in the protocol stack. This is the physical address for the end-station. | 1.3.6.1.4.1.171.10.75.1.11.13 | MacAddress | read-only | mandatory |
| configPasswordAdmin OBJECT-TYPE The adminstrator password | 1.3.6.1.4.1.171.10.75.1.11.15 | DisplayString (SIZE(0..20)) | write-only | mandatory |
| configIpAddress OBJECT-TYPE The IP Address for the RDU box. | 1.3.6.1.4.1.171.10.75.1.11.16 | IpAddress | read-write | mandatory |
| configNetMask OBJECT-TYPE The network mask for the RDU box. | 1.3.6.1.4.1.171.10.75.1.11.17 | IpAddress | read-write | mandatory |
| configGateway OBJECT-TYPE The Gatway Address for the unit. | 1.3.6.1.4.1.171.10.75.1.11.18 | IpAddress | read-write | mandatory |
| configSave OBJECT-TYPE Physically saves the current configuration to nvram. - use with care. (1) saves the configuration (2) does nothing. | 1.3.6.1.4.1.171.10.75.1.11.19 | INTEGER {save(1), noop(2)} | read-write | mandatory |
| configRestoreDefaults OBJECT-TYPE Restores the configuration of the unit to the original settings. | 1.3.6.1.4.1.171.10.75.1.11.22 | INTEGER {restore(1), noop(2)} | read-write | mandatory |
| companyTVlanGroup OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75.1.13 | |||
| tvlanTable OBJECT-TYPE A list of the VLANs | 1.3.6.1.4.1.171.10.75.1.13.1 | not-accessible | mandatory | |
| tvlanEntry OBJECT-TYPE A VLAN entry containing the VLAN id and name. | 1.3.6.1.4.1.171.10.75.1.13.1.1 | not-accessible | mandatory | |
| tvlanId OBJECT-TYPE The VLAN identifier. A maximum of 64 VLANs is supported. The value must be from 2 to 4094. | 1.3.6.1.4.1.171.10.75.1.13.1.1.1 | INTEGER | read-only | mandatory |
| tvlanMember OBJECT-TYPE The set of the device's member ports that belong to the VLAN. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the VLAN is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. | 1.3.6.1.4.1.171.10.75.1.13.1.1.3 | PortList | read-write | mandatory |
| tvlanUntaggedPorts OBJECT-TYPE If that bit has a value of '1' the outgoing frame on the egress port is untagged. If that bit has a value of '0' the outgoing frame on the egress port is tagged. | 1.3.6.1.4.1.171.10.75.1.13.1.1.4 | PortList | read-write | mandatory |
| tvlanStatus OBJECT-TYPE The status of an entry in the VLAN Table. Only a subset of the rowstatus variables (active, createAndGo, createAndWait, destroy) are available. | 1.3.6.1.4.1.171.10.75.1.13.1.1.5 | INTEGER {active(1), notReady(3), createAndGo(4), createAndWait(5), destroy(6)} | read-write | mandatory |
| tvlanPortTable OBJECT-TYPE A list of ports and their associated VLAN. | 1.3.6.1.4.1.171.10.75.1.13.2 | not-accessible | mandatory | |
| tvlanPortEntry OBJECT-TYPE Information pertaining to an individual port regarding to which VLAN it belongs. | 1.3.6.1.4.1.171.10.75.1.13.2.1 | not-accessible | mandatory | |
| tvlanPortPortId OBJECT-TYPE A port identifier that is in the range of 1 to ifNumber. | 1.3.6.1.4.1.171.10.75.1.13.2.1.1 | INTEGER | read-only | mandatory |
| tvlanPortVlanId OBJECT-TYPE The default VLAN identifier. | 1.3.6.1.4.1.171.10.75.1.13.2.1.2 | INTEGER | read-write | mandatory |
| companyPortTrunkGroup OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75.1.14 | |||
| portTrunkTable OBJECT-TYPE A list of port trunks and their associated members. | 1.3.6.1.4.1.171.10.75.1.14.1 | not-accessible | mandatory | |
| portTrunkEntry OBJECT-TYPE A port trunk entry containing the trunk id and trunk members. | 1.3.6.1.4.1.171.10.75.1.14.1.1 | not-accessible | mandatory | |
| portTrunkId OBJECT-TYPE The port trunk identifier. The current range is from 1 to 3. | 1.3.6.1.4.1.171.10.75.1.14.1.1.1 | INTEGER | read-only | mandatory |
| portTrunkMember OBJECT-TYPE Trunk group 1 - 2 has twelve members (Port 01/13 - 12/24). Trunk group 3 has two members (Port 25-26). Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. | 1.3.6.1.4.1.171.10.75.1.14.1.1.2 | PortList | read-only | mandatory |
| portTrunkMemberValue OBJECT-TYPE A port trunk member value indicates which port is a member of the specified trunk. Valid values are in the range from 0 to ifNumber. A zero indicates that no port is contained in the specifed member. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. | 1.3.6.1.4.1.171.10.75.1.14.1.1.3 | PortList | read-write | mandatory |
| portTrunkEnable OBJECT-TYPE Enable/Disable Trunk group. A (1) enables, a (2) disables. | 1.3.6.1.4.1.171.10.75.1.14.1.1.4 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| companyQoSGroup OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75.1.15 | |||
| qos8021pTable OBJECT-TYPE A list of priorities and their Queue-Level. | 1.3.6.1.4.1.171.10.75.1.15.2 | not-accessible | mandatory | |
| qos8021pEntry OBJECT-TYPE A 802.1P Based QoS entry containing the priority and Queue-Level. | 1.3.6.1.4.1.171.10.75.1.15.2.1 | not-accessible | mandatory | |
| qos8021pPriority OBJECT-TYPE A priority identifier that is in the range of 0 to 7. | 1.3.6.1.4.1.171.10.75.1.15.2.1.1 | INTEGER | read-only | mandatory |
| qos8021pQueueLevel OBJECT-TYPE The priority's Queue-Level. | 1.3.6.1.4.1.171.10.75.1.15.2.1.2 | INTEGER {normal(1), high(2)} | read-write | mandatory |
| companyStaticGroup OBJECT-IDENTITY | 1.3.6.1.4.1.171.10.75.1.21 | |||
| staticOnOff OBJECT-TYPE Enable/Disable Static MAC. A (1) enables, a (2) disables. | 1.3.6.1.4.1.171.10.75.1.21.1 | INTEGER {enabled(1), disabled(2)} | read-write | mandatory |
| staticAutoLearning OBJECT-TYPE The set of the device's member ports that belong to the Static MAC auto learning enable/disable. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is in auto learning enable state; the port is not in auto learning state if its bit has a value of '0'. | 1.3.6.1.4.1.171.10.75.1.21.2 | PortList | read-write | mandatory |
| staticTable OBJECT-TYPE A list of the Static MACs | 1.3.6.1.4.1.171.10.75.1.21.3 | not-accessible | mandatory | |
| staticEntry OBJECT-TYPE A Static MAC entry containing the mac and forwarding port. | 1.3.6.1.4.1.171.10.75.1.21.3.1 | not-accessible | mandatory | |
| staticId OBJECT-TYPE The Static MAC identifier. A maximum of 60 Static MACs is supported. The value must be from 1 to 60 | 1.3.6.1.4.1.171.10.75.1.21.3.1.1 | INTEGER | read-only | mandatory |
| staticMac OBJECT-TYPE The Static MAC associated with the Id. | 1.3.6.1.4.1.171.10.75.1.21.3.1.2 | MacAddress | read-write | mandatory |
| staticPort OBJECT-TYPE The Static MAC forwarding port with the ID. | 1.3.6.1.4.1.171.10.75.1.21.3.1.3 | INTEGER | read-write | mandatory |
| staticVID OBJECT-TYPE The Static MAC VID with the ID. | 1.3.6.1.4.1.171.10.75.1.21.3.1.4 | INTEGER | read-write | mandatory |
| staticStatus OBJECT-TYPE The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. | 1.3.6.1.4.1.171.10.75.1.21.3.1.5 | INTEGER {active(1), createAndGo(4), destroy(6)} | read-write | mandatory |
Notifications
| Name | OID | Status |
|---|---|---|
| swFiberInsert NOTIFICATION-TYPE Fiber insert trap | 1.3.6.1.4.1.171.10.75.1.0.1 | |
| swFiberRemove NOTIFICATION-TYPE Fiber remove trap | 1.3.6.1.4.1.171.10.75.1.0.2 |