MIBs Depot

DES-1210-52_BX

Registered at
1.3.6.1.4.1.171.10.75.7.2.5
1.3.6.1.4.1.171.10.75.7.3.9
1.3.6.1.4.1.171.10.75.7.3.10
1.3.6.1.4.1.171.10.75.7.11.1.3
1.3.6.1.4.1.171.10.75.7.12.5
1.3.6.1.4.1.171.10.75.7.12.6
1.3.6.1.4.1.171.10.75.7.14.9
1.3.6.1.4.1.171.10.75.7.14.10
1.3.6.1.4.1.171.10.75.7.16.2
1.3.6.1.4.1.171.10.75.7.20.17
1.3.6.1.4.1.171.10.75.7.21.3
1.3.6.1.4.1.171.10.75.7.24
1.3.6.1.4.1.171.10.75.7.31
1.3.6.1.4.1.171.10.75.7.32
1.3.6.1.4.1.171.10.75.7.35
1.3.6.1.4.1.171.10.75.7.37
1.3.6.1.4.1.171.10.75.7.47
1.3.6.1.4.1.171.10.75.7.50
Namespace
dlink
Source file
DES-1210-52_BX
Digest
sha256:7388533fa2fcb59a9275db03977730d7a5a94950778a0e4d282b3a4f7b733ba0

Imports

FromSymbols
BRIDGE-MIBdot1dBasePort, dot1dBasePortEntry, dot1dBridge
IANA-ADDRESS-FAMILY-NUMBERS-MIBAddressFamilyNumbers
IF-MIBInterfaceIndex, InterfaceIndexOrZero
INET-ADDRESS-MIBInetAddress
SNMP-FRAMEWORK-MIBSnmpAdminString, SnmpEngineID, SnmpSecurityLevel
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso
SNMPv2-TCDisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

BRIDGE-MIB
DES-1210-52_BX
IANA-ADDRESS-FAMILY-NUMBERS-MIB
IANAifType-MIB
IF-MIB
INET-ADDRESS-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
BridgeId
TEXTUAL-CONVENTION
The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge). Several objects in this MIB module represent values of timers used by the Spanning Tree Protocol. In this MIB, these timers have values in units of hundreths of a second (i.e. 1/100 secs). These timers, when stored in a Spanning Tree Protocol's BPDU, are in units of 1/256 seconds. Note, however, that 802.1D-1990 specifies a settable granularity of no more than 1 second for these timers. To avoid ambiguity, a data type is defined here as a textual convention and all representation of these timers in this MIB module are defined using this data type. An algorithm is also defined for converting between the different units, to ensure a timer's value is not distorted by multiple conversions.
current
Ipv6Address
TEXTUAL-CONVENTION
This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.
current
LacpKey
TEXTUAL-CONVENTION
The Actor or Partner Key value (0..65535).
current
LldpManAddress
TEXTUAL-CONVENTION
The value of a management address associated with the LLDP agent that may be used to reach higher layer entities to assist discovery by network management. It should be noted that appropriate security credentials, such as SNMP engineId, may be required to access the LLDP agent using a management address. These necessary credentials should be known by the network management and the objects associated with the credentials are not included in the LLDP agent.
current
PortLaMode
TEXTUAL-CONVENTION
Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. static(2) - force the port to enable channeling. disable(3) - channeling is disabled.
current
PortList
TEXTUAL-CONVENTION
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
current
RmonStatus
TEXTUAL-CONVENTION
The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries currently not in use. Proper interpretation of such entries requires examination of the relevant RmonStatus object. An existing instance of this object cannot be set to createRequest(2). This object may only be set to createRequest(2) when this instance is created. When this object is created, the agent may wish to create supplemental object instances with default values to complete a conceptual row in this table. Because the creation of these default objects is entirely at the option of the agent, the manager must not assume that any will be created, but may make use of any that are created. Immediately after completing the create operation, the agent must set this object to underCreation(3). When in the underCreation(3) state, an entry is allowed to exist in a possibly incomplete, possibly inconsistent state, usually to allow it to be modified in multiple PDUs. When in this state, an entry is not fully active. Entries shall exist in the underCreation(3) state until the management station is finished configuring the entry and sets this object to valid(1) or aborts, setting this object to invalid(4). If the agent determines that an entry has been in the underCreation(3) state for an abnormally long time, it may decide that the management station has crashed. If the agent makes this decision, it may set this object to invalid(4) to reclaim the entry. A prudent agent will understand that the management station may need to wait for human input and will allow for that possibility in its determination of this abnormally long period. An entry in the valid(1) state is fully configured and consistent and fully represents the configuration or operation such a row is intended to represent. For example, it could be a statistical function that is configured and active, or a filter that is available in the list of filters processed by the packet capture process. A manager is restricted to changing the state of an entry in the following ways: To: valid createRequest underCreation invalid From: valid OK NO OK OK createRequest N/A N/A N/A N/A underCreation OK NO OK OK invalid NO NO NO OK nonExistent NO OK NO OK In the table above, it is not applicable to move the state from the createRequest state to any other state because the manager will never find the variable in that state. The nonExistent state is not a value of the enumeration, rather it means that the entryStatus variable does not exist at all. An agent may allow an entryStatus variable to change state in additional ways, so long as the semantics of the states are followed. This allowance is made to ease the implementation of the agent and is made despite the fact that managers should never exercise these additional state transitions.
current
Timeout
TEXTUAL-CONVENTION
A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n is the value in 1/100 second units b is the value in 1/256 second units To convert the value from 1/256 second units back to 1/100 seconds, the following algorithm should be used: n = ceiling( (b * 100) / 256) where: ceiling = quotient [if remainder is 0], or quotient + 1 [if remainder is non-zero] n is the value in 1/100 second units b is the value in 1/256 second units Note: it is important that the arithmetic operations are done in the order specified (i.e., multiply first, divide second).
current
VlanIndex
TEXTUAL-CONVENTION
A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB.
current

Objects

NameOIDSyntaxAccessStatus
des_1210_52bx
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7
companySystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.1
sysSwitchName
OBJECT-TYPE
System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) ¡V + _ = .
1.3.6.1.4.1.171.10.75.7.1.1DisplayString (SIZE(1..20))read-writecurrent
sysHardwareVersion
OBJECT-TYPE
Version number of the Hardware.
1.3.6.1.4.1.171.10.75.7.1.2DisplayString (SIZE(1..15))read-onlycurrent
sysFirmwareVersion
OBJECT-TYPE
Version number of the Firmware.
1.3.6.1.4.1.171.10.75.7.1.3DisplayString (SIZE(1..15))read-onlycurrent
sysLoginTimeoutInterval
OBJECT-TYPE
This time interval is used to count the time and logout web interface automatically.
1.3.6.1.4.1.171.10.75.7.1.4Integer32 (3..30)read-writecurrent
sysLocationName
OBJECT-TYPE
The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.
1.3.6.1.4.1.171.10.75.7.1.5DisplayString (SIZE(1..20))read-writecurrent
sysGroupInterval
OBJECT-TYPE
Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Interval.
1.3.6.1.4.1.171.10.75.7.1.6Integer32 (0 | 120..1225)read-writecurrent
sysSystemPassword
OBJECT-TYPE
This object is used to set System Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.
1.3.6.1.4.1.171.10.75.7.1.7DisplayString (SIZE(1..20))read-writecurrent
sysSafeGuardEnable
OBJECT-TYPE
This object is used to set Safeguard Enable\Disable.
1.3.6.1.4.1.171.10.75.7.1.8INTEGER {enable(1), disable(2)}read-writecurrent
sysRestart
OBJECT-TYPE
This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'.
1.3.6.1.4.1.171.10.75.7.1.9TruthValueread-writecurrent
sysSave
OBJECT-TYPE
This object is used to save Configuration.
1.3.6.1.4.1.171.10.75.7.1.10TruthValueread-writecurrent
sysPortCtrlTable
OBJECT-TYPE
A table to control the port specific parameters of the device like speed, duplex mode, etc.
1.3.6.1.4.1.171.10.75.7.1.13not-accessiblecurrent
sysPortCtrlEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.
1.3.6.1.4.1.171.10.75.7.1.13.1not-accessiblecurrent
sysPortCtrlIndex
OBJECT-TYPE
Interface index of the port for the configuration in this entry applies.
1.3.6.1.4.1.171.10.75.7.1.13.1.1Integer32 (1..65535)read-onlycurrent
sysPortCtrlSpeed
OBJECT-TYPE
Configures interface speed.
1.3.6.1.4.1.171.10.75.7.1.13.1.2INTEGER {rate1000M-Full(1), rate100M-Full(2), rate100M-Half(3), rate10M-Full(4), rate10M-Half(5), auto(6), disable(7)}read-writecurrent
sysPortCtrlOperStatus
OBJECT-TYPE
The port's operating speed state.
1.3.6.1.4.1.171.10.75.7.1.13.1.3INTEGER {down(1), rate1000M-Full(2), rate100M-Full(3), rate100M-Half(4), rate10M-Full(5), rate10M-Half(6)}read-onlycurrent
sysPortCtrlMDI
OBJECT-TYPE
Configures interface auto/mdi/mdix mode. The default setting is Auto.
1.3.6.1.4.1.171.10.75.7.1.13.1.4INTEGER {auto(1), mdi(2), mdix(3)}read-writecurrent
sysPortCtrlFlowControl
OBJECT-TYPE
Enables / disables flow control for the interface.
1.3.6.1.4.1.171.10.75.7.1.13.1.5INTEGER {enable(1), disable(2)}read-writecurrent
sysPortCtrlFlowControlOper
OBJECT-TYPE
The link parner negotiate port's operating flow control state.
1.3.6.1.4.1.171.10.75.7.1.13.1.6INTEGER {enabled(1), disabled(2)}read-onlycurrent
sysPortCtrlType
OBJECT-TYPE
The port's media type.
1.3.6.1.4.1.171.10.75.7.1.13.1.7INTEGER {fastethernet(1), gigabitethernet(2), fiberwith100BaseSFPModule(3), fiberwith1000BaseSFPModule(4)}read-onlycurrent
sysDhcpAutoConfiguration
OBJECT-TYPE
This object indicates auto config is enabled or disabled.
1.3.6.1.4.1.171.10.75.7.1.14INTEGER {enable(1), disable(2)}read-writecurrent
companyIpifGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.2
ipv4sysIpAddrCfgMode
OBJECT-TYPE
Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.
1.3.6.1.4.1.171.10.75.7.2.1INTEGER {manual(1), dynamic(2)}read-writeobsolete
ipv4sysIpAddr
OBJECT-TYPE
Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.
1.3.6.1.4.1.171.10.75.7.2.2IpAddressread-writeobsolete
ipv4sysIpSubnetMask
OBJECT-TYPE
IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.
1.3.6.1.4.1.171.10.75.7.2.3IpAddressread-writeobsolete
ipv4sysGateway
OBJECT-TYPE
Gateway
1.3.6.1.4.1.171.10.75.7.2.4IpAddressread-writeobsolete
ipifSupportV4V6Info
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.2.5
sysIpAddrCfgMode
OBJECT-TYPE
Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.
1.3.6.1.4.1.171.10.75.7.2.5.1INTEGER {manual(1), dynamic(2)}read-writecurrent
sysIpAddr
OBJECT-TYPE
Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.
1.3.6.1.4.1.171.10.75.7.2.5.2IpAddressread-writecurrent
sysIpSubnetMask
OBJECT-TYPE
IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.
1.3.6.1.4.1.171.10.75.7.2.5.3IpAddressread-writecurrent
sysGateway
OBJECT-TYPE
Gateway
1.3.6.1.4.1.171.10.75.7.2.5.4IpAddressread-writecurrent
ipifName
OBJECT-TYPE
The Description for the interface.
1.3.6.1.4.1.171.10.75.7.2.5.5OCTET STRINGread-onlycurrent
ipifv6GlobalStatus
OBJECT-TYPE
The ID of VLAN that you want this interface to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.7.2.5.7INTEGER {enable(1), disable(2)}read-createcurrent
ipifv6DHCPStatus
OBJECT-TYPE
The state of DHCPv6 that you want this interface to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.7.2.5.8INTEGER {enable(1), disable(2)}read-createcurrent
ipifv6AutolinkloStatus
OBJECT-TYPE
The global state of link local that you want this interface to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.7.2.5.9INTEGER {enable(1), disable(2)}read-createcurrent
ipifv6NSRetransmitTime
OBJECT-TYPE
The NS's retransmit time that you want this interface to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.7.2.5.10INTEGER (1..3600)read-createcurrent
ipifv6DefaultGateway
OBJECT-TYPE
The ipv6 default gateway that you want this interface to be in. To delete gateway, please insert address '0000:0000:0000:0000:0000:0000:0000:0000'.
1.3.6.1.4.1.171.10.75.7.2.5.11Ipv6Addressread-createcurrent
ipifV6AddressTable
OBJECT-TYPE
A list of interface entries.
1.3.6.1.4.1.171.10.75.7.2.5.12not-accessiblecurrent
ipifV6AddressEntry
OBJECT-TYPE
An entry containing management information applicable to a particular interface.
1.3.6.1.4.1.171.10.75.7.2.5.12.1not-accessiblecurrent
ipifV6AddressMainIndex
OBJECT-TYPE
The index of this IPv6 entry.
1.3.6.1.4.1.171.10.75.7.2.5.12.1.1InterfaceIndexread-onlycurrent
ipifV6AddressIpAddr
OBJECT-TYPE
The ip address of this IPv6 entry.
1.3.6.1.4.1.171.10.75.7.2.5.12.1.2Ipv6Addressread-onlycurrent
ipifV6AddressIpPrefix
OBJECT-TYPE
The ip prefix of this IPv6 entry.
1.3.6.1.4.1.171.10.75.7.2.5.12.1.3INTEGERread-onlycurrent
ipifV6AddressIpType
OBJECT-TYPE
The ip type of this IPv6 entry.
1.3.6.1.4.1.171.10.75.7.2.5.12.1.4INTEGER {unicast(1), anycast(2), linklocal(3)}read-onlycurrent
ipifV6AddressRowStatus
OBJECT-TYPE
The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available.
1.3.6.1.4.1.171.10.75.7.2.5.12.1.5RowStatusread-createcurrent
companyTftpGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.3
tftpFwServerIpAddress
OBJECT-TYPE
The TFTP server's IP address is used to upload or download firmware.
1.3.6.1.4.1.171.10.75.7.3.1IpAddressread-writeobsolete
tftpFwImageFileName
OBJECT-TYPE
Configure firmware filename to download.
1.3.6.1.4.1.171.10.75.7.3.2DisplayString (SIZE(1..64))read-writeobsolete
tftpFwTftpOperation
OBJECT-TYPE
The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName.
1.3.6.1.4.1.171.10.75.7.3.3INTEGER {none(0), download(1), upload(2)}read-writeobsolete
tftpFwTftpOperationStatus
OBJECT-TYPE
The tftp operation status represent firmware backup or upgrade status.
1.3.6.1.4.1.171.10.75.7.3.4INTEGER {none(0), success(1), fail(2), progressing(3), transmit(4)}read-onlyobsolete
tftpCfgServerIpAddress
OBJECT-TYPE
The TFTP server's IP address is used to upload or download configuration file.
1.3.6.1.4.1.171.10.75.7.3.5IpAddressread-writeobsolete
tftpConfigFileName
OBJECT-TYPE
The configuration filename is used to store or retrieve config from the tftp server.
1.3.6.1.4.1.171.10.75.7.3.6DisplayString (SIZE(1..64))read-writeobsolete
tftpConfigTftpOperation
OBJECT-TYPE
The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName.
1.3.6.1.4.1.171.10.75.7.3.7INTEGER {none(0), download(1), upload(2), progressing(3)}read-writeobsolete
tftpConfigTftpOperationStatus
OBJECT-TYPE
The tftp operation status represent configuration file backup or restore status.
1.3.6.1.4.1.171.10.75.7.3.8INTEGER {none(0), success(1), fail(2), progressing(3)}read-onlyobsolete
tftpFwTargetGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.3.9
tftpFwTargetServerIpAddress
OBJECT-TYPE
The TFTP server's IP address is used to upload or download firmware.
1.3.6.1.4.1.171.10.75.7.3.9.1Ipv6Addressread-writecurrent
tftpFwTargetServerIpType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.7.3.9.2INTEGER {iPv4(1), iPv6(2)}read-writecurrent
tftpFwTargetInterfaceName
OBJECT-TYPE
Specifies the interface name when the tftpFwTargetServerIpAddress is linklocal address.
1.3.6.1.4.1.171.10.75.7.3.9.3OCTET STRINGread-writecurrent
tftpFwTargetImageFileName
OBJECT-TYPE
Configure firmware filename to download.
1.3.6.1.4.1.171.10.75.7.3.9.4DisplayString (SIZE(1..64))read-writecurrent
tftpFwTargetTftpOperation
OBJECT-TYPE
The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName.
1.3.6.1.4.1.171.10.75.7.3.9.5INTEGER {none(0), download(1), upload(2)}read-writecurrent
tftpFwTargetTftpOperationStatus
OBJECT-TYPE
The tftp operation status represent firmware backup or upgrade status.
1.3.6.1.4.1.171.10.75.7.3.9.6INTEGER {none(0), success(1), fail(2), progressing(3), transmit(4)}read-onlycurrent
tftpCfgTargetGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.3.10
tftpCfgTargetServerIpAddress
OBJECT-TYPE
The TFTP server's IP address is used to upload or download configuration file.
1.3.6.1.4.1.171.10.75.7.3.10.1Ipv6Addressread-writecurrent
tftpCfgTargetServerIpType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.7.3.10.2INTEGER {iPv4(1), iPv6(2)}read-writecurrent
tftpCfgTargetInterfaceName
OBJECT-TYPE
Specifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address.
1.3.6.1.4.1.171.10.75.7.3.10.3OCTET STRINGread-writecurrent
tftpCfgTargetImageFileName
OBJECT-TYPE
The configuration filename is used to store or retrieve config from the tftp server.
1.3.6.1.4.1.171.10.75.7.3.10.4DisplayString (SIZE(1..64))read-writecurrent
tftpCfgTargetTftpOperation
OBJECT-TYPE
The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName.
1.3.6.1.4.1.171.10.75.7.3.10.5INTEGER {none(0), download(1), upload(2), progressing(3)}read-writecurrent
tftpCfgTargetTftpOperationStatus
OBJECT-TYPE
The tftp operation status represent configuration file backup or restore status.
1.3.6.1.4.1.171.10.75.7.3.10.6INTEGER {none(0), success(1), fail(2), progressing(3)}read-onlycurrent
companyMiscGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.4
miscReset
OBJECT-TYPE
Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing.
1.3.6.1.4.1.171.10.75.7.4.2INTEGER {reset(1), noop(2)}read-writecurrent
miscStatisticsReset
OBJECT-TYPE
Resets the units statistics. A (1) resets the statistics count, a (2) does nothing.
1.3.6.1.4.1.171.10.75.7.4.3INTEGER {reset(1), noop(2)}read-writecurrent
companyRSTP
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.6
stpGlobal
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.6.1
rstpStatus
OBJECT-TYPE
The administrative module status requested by management for the RSTP Module. This enables or disables RSTP in the system. A value of 'enabled' (1) indicates that RSTP must be enabled in the device on all the ports. A value of 'disabled'(2) indicates that RSTP must be disabled in the device on all the ports.
1.3.6.1.4.1.171.10.75.7.6.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
stpVersion
OBJECT-TYPE
The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w. New value may be defined as future versions of the protocol become available.
1.3.6.1.4.1.171.10.75.7.6.1.2INTEGER {stpCompatible(0), rstp(2)}read-writecurrent
stpPriority
OBJECT-TYPE
The bridge priority vector, as defined in 17.6. The first (RootBridgeID) and third (DesignatedBridgeID)components are both equal to the value of the Bridge Identifier (17.18.2). The other components are zero.
1.3.6.1.4.1.171.10.75.7.6.1.3INTEGER (0..61440)read-writecurrent
stpTxHoldCount
OBJECT-TYPE
The value used by the Port Transmit state machine to limit the maximum transmission rate.
1.3.6.1.4.1.171.10.75.7.6.1.4INTEGER (1..10)read-writecurrent
stpProtocolSpecification
OBJECT-TYPE
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
1.3.6.1.4.1.171.10.75.7.6.1.5INTEGER {unknown(1), decLb100(2), ieee8021d(3)}read-onlycurrent
stpTimeSinceTopologyChange
OBJECT-TYPE
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
1.3.6.1.4.1.171.10.75.7.6.1.6TimeTicksread-onlycurrent
stpTopChanges
OBJECT-TYPE
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
1.3.6.1.4.1.171.10.75.7.6.1.7Counter32read-onlycurrent
stpDesignatedRoot
OBJECT-TYPE
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
1.3.6.1.4.1.171.10.75.7.6.1.8BridgeIdread-onlycurrent
stpRootCost
OBJECT-TYPE
The cost of the path to the root as seen from this bridge.
1.3.6.1.4.1.171.10.75.7.6.1.9INTEGERread-onlycurrent
stpRootPort
OBJECT-TYPE
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
1.3.6.1.4.1.171.10.75.7.6.1.10INTEGERread-onlycurrent
stpMaxAge
OBJECT-TYPE
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. The rootTimes variable comprises the Bridge¡¦s operational timer parameter values (Message Age, Max Age, Forward Delay, and Hello Time), derived from the values stored in portTimes (17.19.22) for the Root Port or from BridgeTimes (17.18.4).
1.3.6.1.4.1.171.10.75.7.6.1.11Timeoutread-onlycurrent
stpHelloTime
OBJECT-TYPE
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. The interval between periodic transmissions of Configuration Messages by Designated Ports (Table 17-1).
1.3.6.1.4.1.171.10.75.7.6.1.12Timeoutread-onlycurrent
stpHoldTime
OBJECT-TYPE
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
1.3.6.1.4.1.171.10.75.7.6.1.13INTEGERread-onlycurrent
stpForwardDelay
OBJECT-TYPE
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. The delay used by STP Bridges (17.4) to transition Root and Designated Ports to Forwarding (Table 17-1).
1.3.6.1.4.1.171.10.75.7.6.1.14Timeoutread-onlycurrent
stpBridgeMaxAge
OBJECT-TYPE
The Max Age component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components¡Xthe current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero.
1.3.6.1.4.1.171.10.75.7.6.1.15Timeout (600..4000)read-writecurrent
stpBridgeHelloTime
OBJECT-TYPE
The Hello Time component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components¡Xthe current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero.
1.3.6.1.4.1.171.10.75.7.6.1.16Timeout (100..1000)read-writecurrent
stpBridgeForwardDelay
OBJECT-TYPE
The Forward Delay component of designatedTimes (17.19.5). This time value, measured in units of hundredths of a second. BridgeTimes comprises four components¡Xthe current values of Bridge Forward Delay, Bridge Hello Time, and Bridge Max Age (17.13, Table 17-1), and a Message Age of zero.
1.3.6.1.4.1.171.10.75.7.6.1.17Timeout (400..3000)read-writecurrent
stpPortTable
OBJECT-TYPE
A table that contains port-specific information for the Spanning Tree Protocol.
1.3.6.1.4.1.171.10.75.7.6.2not-accessiblecurrent
stpPortEntry
OBJECT-TYPE
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
1.3.6.1.4.1.171.10.75.7.6.2.1not-accessiblecurrent
stpPort
OBJECT-TYPE
The port number of the port for which this entry contains Spanning Tree Protocol management information.
1.3.6.1.4.1.171.10.75.7.6.2.1.1INTEGER (1..65535)read-onlycurrent
stpPortPriority
OBJECT-TYPE
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of stpPort.
1.3.6.1.4.1.171.10.75.7.6.2.1.2INTEGER (0..240)read-writecurrent
stpPortState
OBJECT-TYPE
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see stpPortEnable), this object will have a value of disabled(1).
1.3.6.1.4.1.171.10.75.7.6.2.1.3INTEGER {disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)}read-onlycurrent
stpPortEnable
OBJECT-TYPE
The enabled/disabled status of the port.
1.3.6.1.4.1.171.10.75.7.6.2.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
stpAdminPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read.
1.3.6.1.4.1.171.10.75.7.6.2.1.5INTEGER (0..200000000)read-writecurrent
stpPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the spanning tree root which include this port.
1.3.6.1.4.1.171.10.75.7.6.2.1.6INTEGER (1..200000000)read-onlycurrent
stpPortDesignatedRoot
OBJECT-TYPE
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
1.3.6.1.4.1.171.10.75.7.6.2.1.7BridgeIdread-onlycurrent
stpPortDesignatedCost
OBJECT-TYPE
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
1.3.6.1.4.1.171.10.75.7.6.2.1.8INTEGERread-onlycurrent
stpPortDesignatedBridge
OBJECT-TYPE
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
1.3.6.1.4.1.171.10.75.7.6.2.1.9BridgeIdread-onlycurrent
stpPortDesignatedPort
OBJECT-TYPE
The Port Identifier of the port on the Designated Bridge for this port's segment.
1.3.6.1.4.1.171.10.75.7.6.2.1.10OCTET STRING (SIZE(2))read-onlycurrent
stpPortForwardTransitions
OBJECT-TYPE
The number of times this port has transitioned from the Learning state to the Forwarding state.
1.3.6.1.4.1.171.10.75.7.6.2.1.11Counter32read-onlycurrent
stpPortProtocolMigration
OBJECT-TYPE
When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.
1.3.6.1.4.1.171.10.75.7.6.2.1.12TruthValueread-writecurrent
stpPortOperEdgePort
OBJECT-TYPE
The operational value of the Edge Port parameter. The object is initialized to the value of stpPortAdminEdgePort and is set FALSE on reception of a BPDU.
1.3.6.1.4.1.171.10.75.7.6.2.1.13TruthValueread-onlycurrent
stpPortAdminPointToPoint
OBJECT-TYPE
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
1.3.6.1.4.1.171.10.75.7.6.2.1.14INTEGER {forceTrue(0), forceFalse(1), auto(2)}read-writecurrent
stpPortOperPointToPoint
OBJECT-TYPE
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-detection, as described in the stpPortAdminPointToPoint object.
1.3.6.1.4.1.171.10.75.7.6.2.1.15TruthValueread-onlycurrent
stpPortEdge
OBJECT-TYPE
This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.
1.3.6.1.4.1.171.10.75.7.6.2.1.16INTEGER {false(0), true(1), auto(2)}read-writecurrent
stpPortRestrictedRole
OBJECT-TYPE
A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.
1.3.6.1.4.1.171.10.75.7.6.2.1.17TruthValueread-writecurrent
stpPortRestrictedTCN
OBJECT-TYPE
A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC_Operational for the attached LANs transitions frequently.
1.3.6.1.4.1.171.10.75.7.6.2.1.18TruthValueread-writecurrent
companyDot1qVlanGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.7
dot1qVlanManagementOnOff
OBJECT-TYPE
Enable/Disable management VLAN mechanism.
1.3.6.1.4.1.171.10.75.7.7.2INTEGER {enabled(1), disabled(2)}read-writecurrent
dot1qVlanManagementid
OBJECT-TYPE
The management VLAN ID, which will allow to forward packets of that VLAN to CPU.
1.3.6.1.4.1.171.10.75.7.7.3INTEGERread-writecurrent
dot1qVlanAsyOnOff
OBJECT-TYPE
Enable/Disable IEEE 802.1Q Asymmetric VLAN
1.3.6.1.4.1.171.10.75.7.7.5INTEGER {enabled(1), disabled(2)}read-writecurrent
dot1qVlanTable
OBJECT-TYPE
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
1.3.6.1.4.1.171.10.75.7.7.6not-accessiblecurrent
dot1qVlanEntry
OBJECT-TYPE
Information for a VLAN configured into the device by (local or network) management.
1.3.6.1.4.1.171.10.75.7.7.6.1not-accessiblecurrent
dot1qVlanName
OBJECT-TYPE
An administratively assigned string, which may be used to identify the VLAN.
1.3.6.1.4.1.171.10.75.7.7.6.1.1SnmpAdminString (SIZE(0..20))read-createcurrent
dot1qVlanEgressPorts
OBJECT-TYPE
The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.
1.3.6.1.4.1.171.10.75.7.7.6.1.2PortListread-createcurrent
dot1qVlanUntaggedPorts
OBJECT-TYPE
The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.
1.3.6.1.4.1.171.10.75.7.7.6.1.4PortListread-createcurrent
dot1qVlanRowStatus
OBJECT-TYPE
The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.
1.3.6.1.4.1.171.10.75.7.7.6.1.5RowStatusread-createcurrent
dot1qVlanPortTable
OBJECT-TYPE
A table containing per port control and status information for VLAN configuration in the device.
1.3.6.1.4.1.171.10.75.7.7.7not-accessiblecurrent
dot1qVlanPortEntry
OBJECT-TYPE
Information controlling VLAN configuration for a port on the device.
1.3.6.1.4.1.171.10.75.7.7.7.1not-accessiblecurrent
dot1qVlanPvid
OBJECT-TYPE
The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port.
1.3.6.1.4.1.171.10.75.7.7.7.1.1VlanIndexread-writecurrent
dot1qVlanUngisterMCFilterTable
OBJECT-TYPE
This table contains the list of ports through which a router, in a particular VLAN is reachable.
1.3.6.1.4.1.171.10.75.7.7.8not-accessiblecurrent
dot1qVlanUngisterMCFilterEntry
OBJECT-TYPE
A list of multicast filter mode information for each VLAN ID.
1.3.6.1.4.1.171.10.75.7.7.8.1not-accessiblecurrent
dot1qVlanUngisterMCFilterVlanId
OBJECT-TYPE
Per Vlan to configure multicast filtering function.
1.3.6.1.4.1.171.10.75.7.7.8.1.1Integer32 (1..4094)read-onlycurrent
dot1qVlanUngisterMCFiltermode
OBJECT-TYPE
Filter unknown multicast frames or normal operation(i.e. forwarding)
1.3.6.1.4.1.171.10.75.7.7.8.1.2INTEGER {forward(0), filter(1)}read-writecurrent
companyLA
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.8
laSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.8.1
laStatus
OBJECT-TYPE
Sets the Link Aggregation Module administrative status as enabled or disabled.
1.3.6.1.4.1.171.10.75.7.8.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
laPortChannelTable
OBJECT-TYPE
A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel.
1.3.6.1.4.1.171.10.75.7.8.1.3not-accessiblecurrent
laPortChannelEntry
OBJECT-TYPE
There is one entry in this table for each created port-channel port.
1.3.6.1.4.1.171.10.75.7.8.1.3.1not-accessiblecurrent
laPortChannelIfIndex
OBJECT-TYPE
The index of the port-channel(Aggregator's interface index).
1.3.6.1.4.1.171.10.75.7.8.1.3.1.1InterfaceIndexread-onlycurrent
laPortChannelMemberList
OBJECT-TYPE
Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.
1.3.6.1.4.1.171.10.75.7.8.1.3.1.2PortListread-writecurrent
laPortChannelMode
OBJECT-TYPE
Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.
1.3.6.1.4.1.171.10.75.7.8.1.3.1.3PortLaModeread-writecurrent
laPortControl
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.8.2
laPortControlTable
OBJECT-TYPE
A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port.
1.3.6.1.4.1.171.10.75.7.8.2.1not-accessiblecurrent
laPortControlEntry
OBJECT-TYPE
A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device.
1.3.6.1.4.1.171.10.75.7.8.2.1.1not-accessiblecurrent
laPortControlIndex
OBJECT-TYPE
The index of the port.
1.3.6.1.4.1.171.10.75.7.8.2.1.1.1InterfaceIndexread-onlycurrent
laPortActorActivity
OBJECT-TYPE
This object indicates LACP_Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets.
1.3.6.1.4.1.171.10.75.7.8.2.1.1.3INTEGER {active(1), passive(2)}read-writecurrent
laPortActorTimeout
OBJECT-TYPE
This object indicates LACP_Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds.
1.3.6.1.4.1.171.10.75.7.8.2.1.1.4INTEGER {short(1), long(2)}read-writecurrent
companyStaticMAC
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.9
staticDisableAutoLearn
OBJECT-TYPE
Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning.
1.3.6.1.4.1.171.10.75.7.9.1INTEGER {on(1), off(2)}read-writecurrent
staticAutoLearningList
OBJECT-TYPE
The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable.
1.3.6.1.4.1.171.10.75.7.9.2PortListread-writecurrent
staticTable
OBJECT-TYPE
A list of the Static MACs
1.3.6.1.4.1.171.10.75.7.9.3not-accessiblecurrent
staticEntry
OBJECT-TYPE
A Static MAC entry containing the mac and forwarding port.
1.3.6.1.4.1.171.10.75.7.9.3.1not-accessiblecurrent
staticVlanID
OBJECT-TYPE
The VLAN ID of the static MAC entry.
1.3.6.1.4.1.171.10.75.7.9.3.1.1INTEGERread-onlycurrent
staticMac
OBJECT-TYPE
The MAC address associated of the static MAC entry.
1.3.6.1.4.1.171.10.75.7.9.3.1.2MacAddressread-onlycurrent
staticPort
OBJECT-TYPE
The forwarding port of the static MAC entry.
1.3.6.1.4.1.171.10.75.7.9.3.1.3INTEGERread-onlycurrent
staticStatus
OBJECT-TYPE
The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.
1.3.6.1.4.1.171.10.75.7.9.3.1.4RowStatusread-writecurrent
companyIgsGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.10
igsSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.10.1
igsStatus
OBJECT-TYPE
Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations.
1.3.6.1.4.1.171.10.75.7.10.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
igsRouterPortPurgeInterval
OBJECT-TYPE
This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.
1.3.6.1.4.1.171.10.75.7.10.1.2Integer32 (60..600)read-writecurrent
igsHostPortPurgeInterval
OBJECT-TYPE
This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.
1.3.6.1.4.1.171.10.75.7.10.1.3Integer32 (130..153025)read-writecurrent
igsRobustnessValue
OBJECT-TYPE
When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.
1.3.6.1.4.1.171.10.75.7.10.1.4Integer32 (2..255)read-writecurrent
igsGrpQueryInterval
OBJECT-TYPE
The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.
1.3.6.1.4.1.171.10.75.7.10.1.5Integer32 (1..25)read-writecurrent
igsQueryInterval
OBJECT-TYPE
This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs.
1.3.6.1.4.1.171.10.75.7.10.1.6Integer32 (60..600)read-writecurrent
igsQueryMaxResponseTime
OBJECT-TYPE
The maximum query response time advertised in IGMPv2 general queries on this interface.
1.3.6.1.4.1.171.10.75.7.10.1.7INTEGER (10..25)read-writecurrent
igsReportToAllPort
OBJECT-TYPE
Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards packets to report to all port. When set to 'disabled', the IGS module forwards packets to router port only.
1.3.6.1.4.1.171.10.75.7.10.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.10.3
igsVlanRouterTable
OBJECT-TYPE
This table contains the list of ports through which a router, in a particular VLAN is reachable.
1.3.6.1.4.1.171.10.75.7.10.3.3not-accessiblecurrent
igsVlanRouterEntry
OBJECT-TYPE
An igs vlan router entry contain the igs vlan router port list.
1.3.6.1.4.1.171.10.75.7.10.3.3.1not-accessiblecurrent
igsVlanRouterVlanId
OBJECT-TYPE
It is the VLAN ID of the igs vlan router entry.
1.3.6.1.4.1.171.10.75.7.10.3.3.1.1Integer32 (1..4094)read-onlycurrent
igsVlanRouterPortList
OBJECT-TYPE
List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.
1.3.6.1.4.1.171.10.75.7.10.3.3.1.2PortListread-onlycurrent
igsVlanFilterTable
OBJECT-TYPE
This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.
1.3.6.1.4.1.171.10.75.7.10.3.4not-accessiblecurrent
igsVlanFilterEntry
OBJECT-TYPE
Contains snooping status , version and fast leave configuration for a specific VLAN.
1.3.6.1.4.1.171.10.75.7.10.3.4.1not-accessiblecurrent
igsVlanFilterVlanId
OBJECT-TYPE
Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.
1.3.6.1.4.1.171.10.75.7.10.3.4.1.1Integer32 (1..4094)read-onlycurrent
igsVlanSnoopStatus
OBJECT-TYPE
This object allows you to enable/disable IGS function on a specific VLAN.
1.3.6.1.4.1.171.10.75.7.10.3.4.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanQuerier
OBJECT-TYPE
Indicates whether the switch is configured as a querier in the VLAN
1.3.6.1.4.1.171.10.75.7.10.3.4.1.3INTEGER {enabled(1), disabled(2)}read-onlycurrent
igsVlanCfgQuerier
OBJECT-TYPE
The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.
1.3.6.1.4.1.171.10.75.7.10.3.4.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanQueryInterval
OBJECT-TYPE
This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.
1.3.6.1.4.1.171.10.75.7.10.3.4.1.5Integer32 (60..600)read-onlycurrent
igsVlanRtrPortList
OBJECT-TYPE
List of ports which are configured statically as router ports
1.3.6.1.4.1.171.10.75.7.10.3.4.1.6PortListread-writecurrent
igsVlanFastLeave
OBJECT-TYPE
Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table.
1.3.6.1.4.1.171.10.75.7.10.3.4.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanMulticastGroupTable
OBJECT-TYPE
This table contains MAC based multicast forwarding information.
1.3.6.1.4.1.171.10.75.7.10.3.5not-accessiblecurrent
igsVlanMulticastGroupEntry
OBJECT-TYPE
This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.
1.3.6.1.4.1.171.10.75.7.10.3.5.1not-accessiblecurrent
igsVlanMulticastGroupVlanId
OBJECT-TYPE
VLAN ID pertaining to the Multicast forwarding entry
1.3.6.1.4.1.171.10.75.7.10.3.5.1.1Integer32 (1..4094)read-onlycurrent
igsVlanMulticastGroupIpAddress
OBJECT-TYPE
Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.
1.3.6.1.4.1.171.10.75.7.10.3.5.1.2InetAddressread-onlycurrent
igsVlanMulticastGroupMacAddress
OBJECT-TYPE
Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.
1.3.6.1.4.1.171.10.75.7.10.3.5.1.3MacAddressread-onlycurrent
igsVlanMulticastGroupPortList
OBJECT-TYPE
List of ports onto which the multicast data packets destined for this group will be forwarded.
1.3.6.1.4.1.171.10.75.7.10.3.5.1.4PortListread-onlycurrent
companyDot1xGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.11
radius
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.11.1
ipv4radiusServerAddress
OBJECT-TYPE
The IP address of the RADIUS server referred to in this table entry.
1.3.6.1.4.1.171.10.75.7.11.1.1IpAddressread-writeobsolete
ipv4radiusServerSharedSecret
OBJECT-TYPE
The secret string which is shared between Server and Client
1.3.6.1.4.1.171.10.75.7.11.1.2DisplayString (SIZE(1..32))read-writeobsolete
radiusServerTable
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.11.1.3
swRadiusServerIPType
OBJECT-TYPE
The IP address of the RADIUS server IP type referred to in this table entry.
1.3.6.1.4.1.171.10.75.7.11.1.3.1INTEGER {iPv4(1), iPv6(2)}read-writecurrent
swRadiusServerAddress
OBJECT-TYPE
The IP address of the RADIUS server referred to in this table entry.
1.3.6.1.4.1.171.10.75.7.11.1.3.2Ipv6Addressread-writecurrent
swRadiusServerInterfaceName
OBJECT-TYPE
Specifies the interface name when the swAuthRadiusServerAddress is linklocal address.
1.3.6.1.4.1.171.10.75.7.11.1.3.3OCTET STRINGread-createcurrent
swRadiusServerSharedSecret
OBJECT-TYPE
The secret string which is shared between Server and Client, the maximum length are 32 chars
1.3.6.1.4.1.171.10.75.7.11.1.3.4DisplayString (SIZE(1..32))read-writecurrent
dot1xAuth
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.11.2
dot1xAuthStatus
OBJECT-TYPE
Enable/Disable Static 802.1x.
1.3.6.1.4.1.171.10.75.7.11.2.1INTEGER {enabled(1), disabled(2)}read-writecurrent
dot1xAuthQuietPeriod
OBJECT-TYPE
The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine.
1.3.6.1.4.1.171.10.75.7.11.2.2INTEGER (0..65535)read-writecurrent
dot1xAuthTxPeriod
OBJECT-TYPE
The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine.
1.3.6.1.4.1.171.10.75.7.11.2.3INTEGER (1..65535)read-writecurrent
dot1xAuthSuppTimeout
OBJECT-TYPE
The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.7.11.2.4INTEGER (1..65535)read-writecurrent
dot1xAuthServerTimeout
OBJECT-TYPE
The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.7.11.2.5INTEGER (1..65535)read-writecurrent
dot1xAuthMaxReq
OBJECT-TYPE
The value of the maxReq constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.7.11.2.6INTEGER (1..10)read-writecurrent
dot1xAuthReAuthPeriod
OBJECT-TYPE
The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine.
1.3.6.1.4.1.171.10.75.7.11.2.7Unsigned32 (1..4294967295)read-writecurrent
dot1xAuthReAuthEnabled
OBJECT-TYPE
The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1).
1.3.6.1.4.1.171.10.75.7.11.2.8INTEGER {enabled(1), disabled(2)}read-writecurrent
dot1xAuthConfigPortTable
OBJECT-TYPE
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
1.3.6.1.4.1.171.10.75.7.11.2.9not-accessiblecurrent
dot1xAuthConfigPortEntry
OBJECT-TYPE
The configuration information for an Authenticator Port.
1.3.6.1.4.1.171.10.75.7.11.2.9.1not-accessiblecurrent
dot1xAuthConfigPortNumber
OBJECT-TYPE
A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number.
1.3.6.1.4.1.171.10.75.7.11.2.9.1.1INTEGERread-onlycurrent
dot1xAuthConfigPortControl
OBJECT-TYPE
The current value of the controlled Port control parameter for the Port.
1.3.6.1.4.1.171.10.75.7.11.2.9.1.2INTEGER {forceUnauthorized(1), auto(2), forceAuthorized(3)}read-writecurrent
dot1xAuthConfigPortStatus
OBJECT-TYPE
The current value of the controlled Port status parameter for the Port.
1.3.6.1.4.1.171.10.75.7.11.2.9.1.3INTEGER {authorized(1), unauthorized(2)}read-onlycurrent
dot1xAuthConfigPortSessionTime
OBJECT-TYPE
The duration of the session in seconds.
1.3.6.1.4.1.171.10.75.7.11.2.9.1.4TimeTicksread-onlycurrent
dot1xAuthConfigPortSessionUserName
OBJECT-TYPE
The User-Name representing the identity of the Supplicant PAE.
1.3.6.1.4.1.171.10.75.7.11.2.9.1.5SnmpAdminStringread-onlycurrent
companyQoSGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.12
qosMode
OBJECT-TYPE
Settings of Qos mode: IEEE 802.1p QoS or DSCP QoS or TOS Qos. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) and Highest(6,7), inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic. DSCP : Differentiated services enhancements to the Internet protocol are intended to enable scalable service discrimination in the Internet without the need for per-flow state and signaling at every hop.
1.3.6.1.4.1.171.10.75.7.12.1INTEGER {dot1p(1), dscp(2), tos(3)}read-writecurrent
queuingMechanism
OBJECT-TYPE
Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS4 spec. Queues with higher weights get bandwidth before than other queues with less weights.
1.3.6.1.4.1.171.10.75.7.12.2INTEGER {strictPriority(1), wrr(2)}read-writecurrent
qosQ1p
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.12.3
dot1pPortTable
OBJECT-TYPE
A list of 802.1p port default priority Entries.
1.3.6.1.4.1.171.10.75.7.12.3.1not-accessiblecurrent
dot1pPortEntry
OBJECT-TYPE
A list of 802.1p port default priority priorities.
1.3.6.1.4.1.171.10.75.7.12.3.1.1not-accessiblecurrent
dot1pPortIndex
OBJECT-TYPE
A port identifier that is in the range of 1 to ifNumber.
1.3.6.1.4.1.171.10.75.7.12.3.1.1.1INTEGERread-onlycurrent
dot1pPortPriority
OBJECT-TYPE
For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, D-Link Smart Switches will refer to their 802.1p information and prioritize them with 4 different priority queues.
1.3.6.1.4.1.171.10.75.7.12.3.1.1.2INTEGER {low(1), medium(2), high(3), highest(4)}read-writecurrent
qosDiffServ
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.12.4
qosDiffServEnable
OBJECT-TYPE
Display the DSCP(Differentiated services) function Enabled or Disabled. Notice : DiffServ Type is 2~7 bits in the TOS field. ex: If the DiffServ Type = 000011(3), the value in TOS field is 00001100(12)
1.3.6.1.4.1.171.10.75.7.12.4.1INTEGER {enable(1), disable(2)}read-onlycurrent
qosDiffServTypeGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.12.4.2
qosDiffServType00
OBJECT-TYPE
DiffServ Type 0 : IP ToS value = 0
1.3.6.1.4.1.171.10.75.7.12.4.2.1INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType01
OBJECT-TYPE
DiffServ Type 01 : IP ToS value = 4
1.3.6.1.4.1.171.10.75.7.12.4.2.2INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType02
OBJECT-TYPE
DiffServ Type 02 : IP ToS value = 8
1.3.6.1.4.1.171.10.75.7.12.4.2.3INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType03
OBJECT-TYPE
DiffServ Type 03 : IP ToS value = 12
1.3.6.1.4.1.171.10.75.7.12.4.2.4INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType04
OBJECT-TYPE
DiffServ Type 04 : IP ToS value = 16
1.3.6.1.4.1.171.10.75.7.12.4.2.5INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType05
OBJECT-TYPE
DiffServ Type 05 : IP ToS value = 20
1.3.6.1.4.1.171.10.75.7.12.4.2.6INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType06
OBJECT-TYPE
DiffServ Type 06 : IP ToS value = 24
1.3.6.1.4.1.171.10.75.7.12.4.2.7INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType07
OBJECT-TYPE
DiffServ Type 07 : IP ToS value = 28
1.3.6.1.4.1.171.10.75.7.12.4.2.8INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType08
OBJECT-TYPE
DiffServ Type 08 : IP ToS value = 32
1.3.6.1.4.1.171.10.75.7.12.4.2.9INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType09
OBJECT-TYPE
DiffServ Type 09 : IP ToS value = 36
1.3.6.1.4.1.171.10.75.7.12.4.2.10INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType10
OBJECT-TYPE
DiffServ Type 10 : IP ToS value = 40
1.3.6.1.4.1.171.10.75.7.12.4.2.11INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType11
OBJECT-TYPE
DiffServ Type 11 : IP ToS value = 44
1.3.6.1.4.1.171.10.75.7.12.4.2.12INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType12
OBJECT-TYPE
DiffServ Type 12 : IP ToS value = 48
1.3.6.1.4.1.171.10.75.7.12.4.2.13INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType13
OBJECT-TYPE
DiffServ Type 13 : IP ToS value = 52
1.3.6.1.4.1.171.10.75.7.12.4.2.14INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType14
OBJECT-TYPE
DiffServ Type 14 : IP ToS value = 56
1.3.6.1.4.1.171.10.75.7.12.4.2.15INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType15
OBJECT-TYPE
DiffServ Type 15 : IP ToS value = 60
1.3.6.1.4.1.171.10.75.7.12.4.2.16INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType16
OBJECT-TYPE
DiffServ Type 16 : IP ToS value = 64
1.3.6.1.4.1.171.10.75.7.12.4.2.17INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType17
OBJECT-TYPE
DiffServ Type 17 : IP ToS value = 68
1.3.6.1.4.1.171.10.75.7.12.4.2.18INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType18
OBJECT-TYPE
DiffServ Type 18 : IP ToS value = 72
1.3.6.1.4.1.171.10.75.7.12.4.2.19INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType19
OBJECT-TYPE
DiffServ Type 19 : IP ToS value = 76
1.3.6.1.4.1.171.10.75.7.12.4.2.20INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType20
OBJECT-TYPE
DiffServ Type 20 : IP ToS value = 80
1.3.6.1.4.1.171.10.75.7.12.4.2.21INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType21
OBJECT-TYPE
DiffServ Type 21 : IP ToS value = 84
1.3.6.1.4.1.171.10.75.7.12.4.2.22INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType22
OBJECT-TYPE
DiffServ Type 22 : IP ToS value = 88
1.3.6.1.4.1.171.10.75.7.12.4.2.23INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType23
OBJECT-TYPE
DiffServ Type 23 : IP ToS value = 92
1.3.6.1.4.1.171.10.75.7.12.4.2.24INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType24
OBJECT-TYPE
DiffServ Type 24 : IP ToS value = 96
1.3.6.1.4.1.171.10.75.7.12.4.2.25INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType25
OBJECT-TYPE
DiffServ Type 25 : IP ToS value = 100
1.3.6.1.4.1.171.10.75.7.12.4.2.26INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType26
OBJECT-TYPE
DiffServ Type 26 : IP ToS value = 104
1.3.6.1.4.1.171.10.75.7.12.4.2.27INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType27
OBJECT-TYPE
DiffServ Type 27 : IP ToS value = 108
1.3.6.1.4.1.171.10.75.7.12.4.2.28INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType28
OBJECT-TYPE
DiffServ Type 28 : IP ToS value = 112
1.3.6.1.4.1.171.10.75.7.12.4.2.29INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType29
OBJECT-TYPE
DiffServ Type 29 : IP ToS value = 116
1.3.6.1.4.1.171.10.75.7.12.4.2.30INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType30
OBJECT-TYPE
DiffServ Type 30 : IP ToS value = 120
1.3.6.1.4.1.171.10.75.7.12.4.2.31INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType31
OBJECT-TYPE
DiffServ Type 31 : IP ToS value = 124
1.3.6.1.4.1.171.10.75.7.12.4.2.32INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType32
OBJECT-TYPE
DiffServ Type 32 : IP ToS value = 128
1.3.6.1.4.1.171.10.75.7.12.4.2.33INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType33
OBJECT-TYPE
DiffServ Type 33 : IP ToS value = 132
1.3.6.1.4.1.171.10.75.7.12.4.2.34INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType34
OBJECT-TYPE
DiffServ Type 34 : IP ToS value = 136
1.3.6.1.4.1.171.10.75.7.12.4.2.35INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType35
OBJECT-TYPE
DiffServ Type 35 : IP ToS value = 140
1.3.6.1.4.1.171.10.75.7.12.4.2.36INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType36
OBJECT-TYPE
DiffServ Type 36 : IP ToS value = 144
1.3.6.1.4.1.171.10.75.7.12.4.2.37INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType37
OBJECT-TYPE
DiffServ Type 37 : IP ToS value = 148
1.3.6.1.4.1.171.10.75.7.12.4.2.38INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType38
OBJECT-TYPE
DiffServ Type 38 : IP ToS value = 152
1.3.6.1.4.1.171.10.75.7.12.4.2.39INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType39
OBJECT-TYPE
DiffServ Type 39 : IP ToS value = 156
1.3.6.1.4.1.171.10.75.7.12.4.2.40INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType40
OBJECT-TYPE
DiffServ Type 40 : IP ToS value = 160
1.3.6.1.4.1.171.10.75.7.12.4.2.41INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType41
OBJECT-TYPE
DiffServ Type 41 : IP ToS value = 164
1.3.6.1.4.1.171.10.75.7.12.4.2.42INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType42
OBJECT-TYPE
DiffServ Type 42 : IP ToS value = 168
1.3.6.1.4.1.171.10.75.7.12.4.2.43INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType43
OBJECT-TYPE
DiffServ Type 43 : IP ToS value = 172
1.3.6.1.4.1.171.10.75.7.12.4.2.44INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType44
OBJECT-TYPE
DiffServ Type 44 : IP ToS value = 176
1.3.6.1.4.1.171.10.75.7.12.4.2.45INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType45
OBJECT-TYPE
DiffServ Type 45 : IP ToS value = 180
1.3.6.1.4.1.171.10.75.7.12.4.2.46INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType46
OBJECT-TYPE
DiffServ Type 46 : IP ToS value = 184
1.3.6.1.4.1.171.10.75.7.12.4.2.47INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType47
OBJECT-TYPE
DiffServ Type 47 : IP ToS value = 188
1.3.6.1.4.1.171.10.75.7.12.4.2.48INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType48
OBJECT-TYPE
DiffServ Type 48 : IP ToS value = 192
1.3.6.1.4.1.171.10.75.7.12.4.2.49INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType49
OBJECT-TYPE
DiffServ Type 49 : IP ToS value = 196
1.3.6.1.4.1.171.10.75.7.12.4.2.50INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType50
OBJECT-TYPE
DiffServ Type 50 : IP ToS value = 200
1.3.6.1.4.1.171.10.75.7.12.4.2.51INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType51
OBJECT-TYPE
DiffServ Type 51 : IP ToS value = 204
1.3.6.1.4.1.171.10.75.7.12.4.2.52INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType52
OBJECT-TYPE
DiffServ Type 52 : IP ToS value = 208
1.3.6.1.4.1.171.10.75.7.12.4.2.53INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType53
OBJECT-TYPE
DiffServ Type 53 : IP ToS value = 212
1.3.6.1.4.1.171.10.75.7.12.4.2.54INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType54
OBJECT-TYPE
DiffServ Type 54 : IP ToS value = 216
1.3.6.1.4.1.171.10.75.7.12.4.2.55INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType55
OBJECT-TYPE
DiffServ Type 55 : IP ToS value = 220
1.3.6.1.4.1.171.10.75.7.12.4.2.56INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType56
OBJECT-TYPE
DiffServ Type 56 : IP ToS value = 224
1.3.6.1.4.1.171.10.75.7.12.4.2.57INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType57
OBJECT-TYPE
DiffServ Type 57 : IP ToS value = 228
1.3.6.1.4.1.171.10.75.7.12.4.2.58INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType58
OBJECT-TYPE
DiffServ Type 58 : IP ToS value = 232
1.3.6.1.4.1.171.10.75.7.12.4.2.59INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType59
OBJECT-TYPE
DiffServ Type 59 : IP ToS value = 236
1.3.6.1.4.1.171.10.75.7.12.4.2.60INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType60
OBJECT-TYPE
DiffServ Type 60 : IP ToS value = 240
1.3.6.1.4.1.171.10.75.7.12.4.2.61INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType61
OBJECT-TYPE
DiffServ Type 61 : IP ToS value = 244
1.3.6.1.4.1.171.10.75.7.12.4.2.62INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType62
OBJECT-TYPE
DiffServ Type 62 : IP ToS value = 248
1.3.6.1.4.1.171.10.75.7.12.4.2.63INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType63
OBJECT-TYPE
DiffServ Type 63 : IP ToS value = 252
1.3.6.1.4.1.171.10.75.7.12.4.2.64INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOS
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.12.5
qosTOSEnable
OBJECT-TYPE
Display the TOS(Type of services) function Enabled or Disabled.
1.3.6.1.4.1.171.10.75.7.12.5.1INTEGER {enable(1), disable(2)}read-onlycurrent
qosTOSGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.12.5.2
qosTOSType00
OBJECT-TYPE
TOS 0
1.3.6.1.4.1.171.10.75.7.12.5.2.1INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType01
OBJECT-TYPE
TOS 01
1.3.6.1.4.1.171.10.75.7.12.5.2.2INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType02
OBJECT-TYPE
TOS 02
1.3.6.1.4.1.171.10.75.7.12.5.2.3INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType03
OBJECT-TYPE
TOS 03
1.3.6.1.4.1.171.10.75.7.12.5.2.4INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType04
OBJECT-TYPE
TOS 04
1.3.6.1.4.1.171.10.75.7.12.5.2.5INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType05
OBJECT-TYPE
TOS 05
1.3.6.1.4.1.171.10.75.7.12.5.2.6INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType06
OBJECT-TYPE
TOS 06
1.3.6.1.4.1.171.10.75.7.12.5.2.7INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType07
OBJECT-TYPE
TOS 07
1.3.6.1.4.1.171.10.75.7.12.5.2.8INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosAclPrioritySettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.12.6
aclQosTable
OBJECT-TYPE
A list of priority by acl setting.
1.3.6.1.4.1.171.10.75.7.12.6.1not-accessiblecurrent
aclQosEntry
OBJECT-TYPE
A list of priority by acl setting entry.
1.3.6.1.4.1.171.10.75.7.12.6.1.1not-accessiblecurrent
aclQosIndex
OBJECT-TYPE
Index of priority by acl setting.
1.3.6.1.4.1.171.10.75.7.12.6.1.1.1Integer32 (1..65535)read-onlycurrent
aclQosType
OBJECT-TYPE
Type of priority by acl setting.
1.3.6.1.4.1.171.10.75.7.12.6.1.1.2INTEGER {tcp(2), udp(3), ipv6traffic_class(7)}read-writecurrent
aclQosTCPUDPPort
OBJECT-TYPE
Dst TCP/UDP port of priority by acl setting, The value '-1',which means don't care this condition
1.3.6.1.4.1.171.10.75.7.12.6.1.1.5Integer32 (1..65535)read-writecurrent
aclQosIP6TC
OBJECT-TYPE
Ipv6 Traffic Class number of priority by acl setting, The value '-1',which means don't care this condition
1.3.6.1.4.1.171.10.75.7.12.6.1.1.10Integer32 (0..255)read-writecurrent
aclQosAssignPriority
OBJECT-TYPE
Be mapped priority by acl setting.
1.3.6.1.4.1.171.10.75.7.12.6.1.1.98INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
aclQosStatus
OBJECT-TYPE
Status of priority by acl setting.
1.3.6.1.4.1.171.10.75.7.12.6.1.1.99RowStatusread-writecurrent
companyTrafficMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.13
bandwidthCtrlSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.13.1
bandwidthCtrlTable
OBJECT-TYPE
A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.7.13.1.2not-accessiblecurrent
bandwidthCtrlEntry
OBJECT-TYPE
An entry appears in this table for each physical interface in the switch.
1.3.6.1.4.1.171.10.75.7.13.1.2.1not-accessiblecurrent
bandwidthCtrlIndex
OBJECT-TYPE
The interface index for which the configuration in this entry applies.
1.3.6.1.4.1.171.10.75.7.13.1.2.1.1Integer32read-onlycurrent
bandwidthCtrlTxThreshold
OBJECT-TYPE
Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port.
1.3.6.1.4.1.171.10.75.7.13.1.2.1.2Integer32 (0 | 64..1024000)read-writecurrent
bandwidthCtrlRxThreshold
OBJECT-TYPE
Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port.
1.3.6.1.4.1.171.10.75.7.13.1.2.1.3Integer32 (0 | 64..1024000)read-writecurrent
broadcastStormCtrlSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.13.3
broadcastStormCtrlGlobalOnOff
OBJECT-TYPE
This object indicates storm control function is enabled or disabled for device. When you enable broadcast storm control function, D-Link Smart Switches will allowed you to limit the number of broadcast packets per second going through device.
1.3.6.1.4.1.171.10.75.7.13.3.1INTEGER {enabled(1), disabled(2)}read-writecurrent
broadcastStormCtrlLimitType
OBJECT-TYPE
This object indicates storm control function is control broadcast packet or multicast packet or dlf packet.
1.3.6.1.4.1.171.10.75.7.13.3.2INTEGER {broadcastonly(1), multicastAndbroadcast(2), dlfMulticastAndbroadcast(3)}read-writecurrent
broadcastStormCtrlThreshold
OBJECT-TYPE
Allows to configure the limiting value for the maximum number of Kbits/sec that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting on this interface. The value that can be set for this object is limited by the underlying hardware. The limit value must be between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port. (Notice : if the limit value is 0, it means unlimited.)
1.3.6.1.4.1.171.10.75.7.13.3.3Integer32 (0 | 64..1024000)read-writecurrent
companySecurity
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14
securityTrustedHost
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14.1
trustedHostStatus
OBJECT-TYPE
This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.
1.3.6.1.4.1.171.10.75.7.14.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
ipv4trustedHostTable
OBJECT-TYPE
A table to configure trusted host in the system.
1.3.6.1.4.1.171.10.75.7.14.1.2not-accessibleobsolete
ipv4trustedHostEntry
OBJECT-TYPE
Each entry in this table represents rules for particular trusted host.
1.3.6.1.4.1.171.10.75.7.14.1.2.1not-accessibleobsolete
ipv4trustedHostIpAddr
OBJECT-TYPE
The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.
1.3.6.1.4.1.171.10.75.7.14.1.2.1.1IpAddressread-onlyobsolete
ipv4trustedHostIpMask
OBJECT-TYPE
Used to mask with IP address, it allow you set a subnet as a trusted host entry.
1.3.6.1.4.1.171.10.75.7.14.1.2.1.2IpAddressread-onlyobsolete
ipv4trustedHostRowStatus
OBJECT-TYPE
The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.7.14.1.2.1.3RowStatusread-createobsolete
trustedHostTable
OBJECT-TYPE
A table to configure trusted host for in the system.
1.3.6.1.4.1.171.10.75.7.14.1.3not-accessiblecurrent
trustedHostEntry
OBJECT-TYPE
Each entry in this table represents rules for particular trusted host.
1.3.6.1.4.1.171.10.75.7.14.1.3.1not-accessiblecurrent
trustedHostIPType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.7.14.1.3.1.1INTEGER {iPv4(1), iPv6(2)}read-onlycurrent
trustedHostIpAddr
OBJECT-TYPE
The IP address of host you allow to access to D-Link Smart Switch. Your local host IPv4/6 Addresses must be one of the IP Addresses to avoid disconnection.
1.3.6.1.4.1.171.10.75.7.14.1.3.1.2Ipv6Addressread-onlycurrent
trustedHostIpMask
OBJECT-TYPE
Used to mask with IPv4/6 address, it allow you set a subnet as a trusted host entry.
1.3.6.1.4.1.171.10.75.7.14.1.3.1.3Ipv6Addressread-onlycurrent
trustedHostRowStatus
OBJECT-TYPE
The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. IPv4 Trust Host created example: 1.4.¡¨IPv4 address¡¨.4.¡¨mask¡¨ IPv6 Trust Host created example: 2.16.¡¨IPv6 address¡¨.1.¡¨prefix¡¨
1.3.6.1.4.1.171.10.75.7.14.1.3.1.4RowStatusread-createcurrent
securityPortSecurity
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14.2
portSecTable
OBJECT-TYPE
A table to control port security features of the device.
1.3.6.1.4.1.171.10.75.7.14.2.1not-accessiblecurrent
portSecEntry
OBJECT-TYPE
An entry appears in port security table for each interface in the system.
1.3.6.1.4.1.171.10.75.7.14.2.1.1not-accessiblecurrent
portSecIndex
OBJECT-TYPE
The interface index for which the configuration in this entry applies.
1.3.6.1.4.1.171.10.75.7.14.2.1.1.1Integer32read-onlycurrent
portSecState
OBJECT-TYPE
Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled.
1.3.6.1.4.1.171.10.75.7.14.2.1.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
portSecMLA
OBJECT-TYPE
Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address.
1.3.6.1.4.1.171.10.75.7.14.2.1.1.3Integer32 (0..64)read-writecurrent
securityARPSpoofPrevent
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14.3
aRPSpoofPreventTable
OBJECT-TYPE
A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.7.14.3.1not-accessiblecurrent
aRPSpoofPreventEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.7.14.3.1.1not-accessiblecurrent
aRPSpoofPreventIpAddr
OBJECT-TYPE
Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.
1.3.6.1.4.1.171.10.75.7.14.3.1.1.1IpAddressnot-accessiblecurrent
aRPSpoofPreventMacAddress
OBJECT-TYPE
Ethernet Mac Address.
1.3.6.1.4.1.171.10.75.7.14.3.1.1.2MacAddressread-writecurrent
aRPSpoofPreventPortList
OBJECT-TYPE
Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.
1.3.6.1.4.1.171.10.75.7.14.3.1.1.3PortListread-writecurrent
aRPSpoofPreventRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.7.14.3.1.1.4RowStatusread-createcurrent
securitySSL
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14.5
sslSecurityHttpStatus
OBJECT-TYPE
This object is for enabling or disabling secure HTTP in the system.
1.3.6.1.4.1.171.10.75.7.14.5.1INTEGER {enable(1), disable(2)}read-writecurrent
sslCiphers
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14.5.2
sslCipherSuiteList
OBJECT-TYPE
This object is to configure the cipher-suites list.
1.3.6.1.4.1.171.10.75.7.14.5.2.1Bits {rsa-null-md5(0), rsa-null-sha(1), rsa-des-sha(2), rsa-3des-sha(3), dh-rsa-des-sha(4), dh-rsa-3des-sha(5), rsa-exp1024-des-sha(6)}read-writecurrent
securityDhcpServerScreen
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14.7
dhcpServerScreenEnablePortlist
OBJECT-TYPE
To enable or disable DHCP Server Screening port list.
1.3.6.1.4.1.171.10.75.7.14.7.1PortListread-writecurrent
ipv4dhcpServerScreenServerTable
OBJECT-TYPE
A table that contains the configuration objects for the DHCP server screen server list. An entry appears in this table for each port that may authenticate access to itself.
1.3.6.1.4.1.171.10.75.7.14.7.2not-accessibleobsolete
ipv4dhcpServerScreenServerEntry
OBJECT-TYPE
The configuration information for an DHCP server screen server.
1.3.6.1.4.1.171.10.75.7.14.7.2.1not-accessibleobsolete
ipv4dhcpServerScreenServerIndex
OBJECT-TYPE
A unique value for DHCP server screen server index. Its value ranges between 1 and 5.
1.3.6.1.4.1.171.10.75.7.14.7.2.1.1INTEGER (1..5)read-onlyobsolete
ipv4dhcpServerScreenServerAddress
OBJECT-TYPE
The IP address of the DHCP server screen server referred to in this table entry.
1.3.6.1.4.1.171.10.75.7.14.7.2.1.2IpAddressread-writeobsolete
ipv4dhcpServerScreenServerStatus
OBJECT-TYPE
The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The dhcpServerScreenServerIndex objects must be explicitly set.
1.3.6.1.4.1.171.10.75.7.14.7.2.1.3RowStatusread-createobsolete
dhcpServerScreenTrustedServerTable
OBJECT-TYPE
A table that contains the configuration objects for the DHCP server screen server list. An entry appears in this table for each port that may authenticate access to itself.
1.3.6.1.4.1.171.10.75.7.14.7.3not-accessiblecurrent
dhcpServerScreenTrustedServerEntry
OBJECT-TYPE
The configuration information for an DHCP server screen server.
1.3.6.1.4.1.171.10.75.7.14.7.3.1not-accessiblecurrent
dhcpServerScreenTrustedServerIndex
OBJECT-TYPE
A unique value for DHCP server screen server index. Its value ranges between 1 and 5.
1.3.6.1.4.1.171.10.75.7.14.7.3.1.1INTEGER (1..5)read-onlycurrent
dhcpServerScreenTrustedServerAddress
OBJECT-TYPE
The IP address of the DHCP server screen server referred to in this table entry.
1.3.6.1.4.1.171.10.75.7.14.7.3.1.2Ipv6Addressread-writecurrent
dhcpServerScreenIPType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.7.14.7.3.1.3INTEGER {iPv4(1), iPv6(2)}read-writecurrent
dhcpServerScreenTrustedServerStatus
OBJECT-TYPE
The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The dhcpServerScreenServerIndex objects must be explicitly set.
1.3.6.1.4.1.171.10.75.7.14.7.3.1.4RowStatusread-createcurrent
securityTrafficSeg
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14.9
trafficSegStatus
OBJECT-TYPE
Enable/Disable Status of Traffic Segmention.
1.3.6.1.4.1.171.10.75.7.14.9.1INTEGER {enabled(1), disabled(2)}read-writecurrent
trafficSegTable
OBJECT-TYPE
A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel
1.3.6.1.4.1.171.10.75.7.14.9.2not-accessiblecurrent
trafficSegEntry
OBJECT-TYPE
There is one entry in this table for each created port-channel port
1.3.6.1.4.1.171.10.75.7.14.9.2.1not-accessiblecurrent
trafficSegIfIndex
OBJECT-TYPE
The ifIndex of the port-channel(Aggregator's interface index).
1.3.6.1.4.1.171.10.75.7.14.9.2.1.1InterfaceIndexread-onlycurrent
trafficSegMemberList
OBJECT-TYPE
Port list of port channel.
1.3.6.1.4.1.171.10.75.7.14.9.2.1.2PortListread-writecurrent
securityIpMacPortBinding
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.14.10
impbSettingTable
OBJECT-TYPE
A table to control IP-MAC-Port Binding Setting features of the device.
1.3.6.1.4.1.171.10.75.7.14.10.1not-accessiblecurrent
impbSettingEntry
OBJECT-TYPE
An entry appears in IP-MAC-Port Binding Setting table for each interface in the system.
1.3.6.1.4.1.171.10.75.7.14.10.1.1not-accessiblecurrent
impbPortIndex
OBJECT-TYPE
Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.
1.3.6.1.4.1.171.10.75.7.14.10.1.1.1INTEGERread-onlycurrent
impbPortState
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding admin state for the interface.
1.3.6.1.4.1.171.10.75.7.14.10.1.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
impbInsIpPacPortState
OBJECT-TYPE
Enable / disable IP-MAC-Port Binding also inspect IP packets state for the interface.
1.3.6.1.4.1.171.10.75.7.14.10.1.1.3INTEGER {disabled(0), enabled(1)}read-writecurrent
impbDHCPPortState
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding DHCP snooping state for the interface.
1.3.6.1.4.1.171.10.75.7.14.10.1.1.4INTEGER {disabled(0), enabled(1)}read-writecurrent
impbSmartTable
OBJECT-TYPE
A table to control Smart IP-MAC-Port Binding features of the device.
1.3.6.1.4.1.171.10.75.7.14.10.2not-accessiblecurrent
impbSmartEntry
OBJECT-TYPE
An entry appears in Smart IP-MAC-Port Binding table for each interface in the system.
1.3.6.1.4.1.171.10.75.7.14.10.2.1not-accessiblecurrent
impbSmartMacAddress
OBJECT-TYPE
The MAC address associated of the smart IP-MAC-PORT Binding entry.
1.3.6.1.4.1.171.10.75.7.14.10.2.1.1MacAddressread-onlycurrent
impbSmartPort
OBJECT-TYPE
The port number of the smart IP-MAC-PORT Binding entry.
1.3.6.1.4.1.171.10.75.7.14.10.2.1.2Integer32read-onlycurrent
impbSmartIpAddress
OBJECT-TYPE
The IP address associated of the smart IP-MAC-PORT Binding entry.
1.3.6.1.4.1.171.10.75.7.14.10.2.1.3IpAddressread-onlycurrent
impbSmartVlanId
OBJECT-TYPE
The VLAN ID of the smart IP-MAC-PORT Binding entry.
1.3.6.1.4.1.171.10.75.7.14.10.2.1.4Integer32read-onlycurrent
impbSmartBinding
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding for the interface.
1.3.6.1.4.1.171.10.75.7.14.10.2.1.5INTEGER {disabled(0), enabled(1)}read-writecurrent
impbWhiteListTable
OBJECT-TYPE
A table to control Manual IP-MAC-Port Binding white list features of the device.
1.3.6.1.4.1.171.10.75.7.14.10.3not-accessiblecurrent
impbWhiteListEntry
OBJECT-TYPE
An entry appears in Manual IP-MAC-Port Binding white list table for each interface in the system.
1.3.6.1.4.1.171.10.75.7.14.10.3.1not-accessiblecurrent
impbWhiteListIpAddress
OBJECT-TYPE
The IP address associated of the Manual IP-MAC-PORT Binding white list entry.
1.3.6.1.4.1.171.10.75.7.14.10.3.1.1IpAddressread-onlycurrent
impbWhiteListMacAddress
OBJECT-TYPE
The MAC address associated of the Manual IP-MAC-PORT Binding white list entry.
1.3.6.1.4.1.171.10.75.7.14.10.3.1.2MacAddressread-onlycurrent
impbWhiteListPort
OBJECT-TYPE
The port number of the Manual IP-MAC-PORT Binding white list entry.
1.3.6.1.4.1.171.10.75.7.14.10.3.1.3Integer32read-writecurrent
impbWhiteListRowStatus
OBJECT-TYPE
The status of a row in impbWhiteListTable. By setting this object, new entries can be created in impbWhiteListTable and existing entries can be removed from impbWhiteListTable. It can be used as specified in the SNMP v2 standard.
1.3.6.1.4.1.171.10.75.7.14.10.3.1.4RowStatusread-createcurrent
impbBlackListTable
OBJECT-TYPE
A table to control IP-MAC-Port Binding black list of the device.
1.3.6.1.4.1.171.10.75.7.14.10.4not-accessiblecurrent
impbBlackListEntry
OBJECT-TYPE
An entry appears in Manual IP-MAC-Port Binding black list table for each interface in the system.
1.3.6.1.4.1.171.10.75.7.14.10.4.1not-accessiblecurrent
impbBlackListMacAddress
OBJECT-TYPE
The MAC address associated of the IP-MAC-PORT Binding black list entry.
1.3.6.1.4.1.171.10.75.7.14.10.4.1.1MacAddressread-onlycurrent
impbBlackListVlanId
OBJECT-TYPE
The VLAN ID of the IP-MAC-PORT Binding black list entry.
1.3.6.1.4.1.171.10.75.7.14.10.4.1.2Integer32read-onlycurrent
impbBlackListPort
OBJECT-TYPE
The port number of the IP-MAC-PORT Binding black list entry.
1.3.6.1.4.1.171.10.75.7.14.10.4.1.3Integer32read-onlycurrent
impbBlackListIpAddress
OBJECT-TYPE
The IP address associated of the IP-MAC-PORT Binding black list entry.
1.3.6.1.4.1.171.10.75.7.14.10.4.1.4IpAddressread-onlycurrent
impbBlackListStatus
OBJECT-TYPE
nothing/delete IP-MAC-Port Binding for the interface.
1.3.6.1.4.1.171.10.75.7.14.10.4.1.5INTEGER {nothing(0), deleted(1)}read-writecurrent
impbAutoScanIpAddressFrom
OBJECT-TYPE
The begin for IP address associated of the IP-MAC-PORT Binding auto scan entry.
1.3.6.1.4.1.171.10.75.7.14.10.5IpAddressread-writecurrent
impbAutoScanIpAddressTo
OBJECT-TYPE
The end for IP address associated of the IP-MAC-PORT Binding auto scan entry.
1.3.6.1.4.1.171.10.75.7.14.10.6IpAddressread-writecurrent
impbAutoScanStatus
OBJECT-TYPE
Nothing / scan IP-MAC-Port Binding auto scan for the interface.
1.3.6.1.4.1.171.10.75.7.14.10.7INTEGER {nothing(0), scan(1)}read-writecurrent
companyACLGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.15
aclProfile
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.15.1
ipv4aclProfileTable
OBJECT-TYPE
A table to ACL profile .
1.3.6.1.4.1.171.10.75.7.15.1.1not-accessibleobsolete
ipv4aclProfileEntry
OBJECT-TYPE
Each entry in this table is a ACL profile. Index to the table is ACL profile ID.
1.3.6.1.4.1.171.10.75.7.15.1.1.1not-accessibleobsolete
ipv4aclProfileNo
OBJECT-TYPE
The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.1Integer32 (1..50)read-onlyobsolete
ipv4aclProfileType
OBJECT-TYPE
The ACL Profile type, possible value are l2 (1) - for MAC-based rule. l3v4 (2) - for IPv4-based rule. impb (3) - for IMPB entry. arpSP_permit(4) - for ARP Spoofing prevention entry. arpSP_deny(5) - for ARP Spoofing prevention entry. voiceVlan(6) - for Voice VLAN OUI entry. surveillanceVlan(7) - for Surveillance VLAN OUI entry. aclQoS(8) - for ACL QoS entry. dhcpServerScreen(10) - for DHCP server screening entry. Note that only l2, l3v4 and l3v6 could be set by user, other is reserved for system to show information.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.2INTEGER {l2(1), l3(2), impb(3), arpSP_permit(4), arpSP_deny(5), voiceVlan(6), surveillanceVlan(7), aclQoS(8), dhcpServerScreen(10)}read-writeobsolete
ipv4aclProfileRuleCount
OBJECT-TYPE
The number of rules in this profile.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.3Integer32 (0..65535)read-onlyobsolete
ipv4aclProfileMask
OBJECT-TYPE
Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 ARP-SP ARP_SENDER_MAC 14 ARP-SP ARP_SENDER_IP 15 (MSB) ------------------------------------------- The value is in Hex format.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.4OCTET STRINGread-writeobsolete
ipv4aclProfileDstMacAddrMask
OBJECT-TYPE
The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.5MacAddressread-writeobsolete
ipv4aclProfileSrcMacAddrMask
OBJECT-TYPE
The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.6MacAddressread-writeobsolete
ipv4aclProfileIPProtocol
OBJECT-TYPE
Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.7INTEGER {none(0), icmp(1), igmp(2), tcp(6), udp(17)}read-writeobsolete
ipv4aclProfileDstIpAddrMask
OBJECT-TYPE
The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.7.15.1.1.1.8IpAddressread-writeobsolete
ipv4aclProfileSrcIpAddrMask
OBJECT-TYPE
The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.7.15.1.1.1.9IpAddressread-writeobsolete
ipv4aclProfileDstPortMask
OBJECT-TYPE
The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.10OCTET STRINGread-writeobsolete
ipv4aclProfileSrcPortMask
OBJECT-TYPE
The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.11OCTET STRINGread-writeobsolete
ipv4aclProfileArpSenderMacAddrMask
OBJECT-TYPE
The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.12MacAddressread-onlyobsolete
ipv4aclProfileArpSenderIpAddrMask
OBJECT-TYPE
The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.13IpAddressread-onlyobsolete
ipv4aclProfileStatus
OBJECT-TYPE
This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.
1.3.6.1.4.1.171.10.75.7.15.1.1.1.14RowStatusread-createobsolete
aclProfileTable
OBJECT-TYPE
A table to ACL profile .
1.3.6.1.4.1.171.10.75.7.15.1.2not-accessiblecurrent
aclProfileEntry
OBJECT-TYPE
Each entry in this table is a ACL profile. Index to the table is ACL profile ID.
1.3.6.1.4.1.171.10.75.7.15.1.2.1not-accessiblecurrent
aclProfileNo
OBJECT-TYPE
The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.1Integer32 (1..50)read-onlycurrent
aclProfileType
OBJECT-TYPE
The ACL Profile type, possible value are l2 (1) - for MAC-based rule. l3v4 (2) - for IPv4-based rule. impb (3) - for IMPB entry. l3v6 (11) - for IPv6-based rule. zone defense (12) - for zone defense entry. arpSP_permit(4) - for ARP Spoofing prevention entry. arpSP_deny(5) - for ARP Spoofing prevention entry. voiceVlan(6) - for Voice VLAN OUI entry. surveillanceVlan(7) - for Surveillance VLAN OUI entry. aclQoS(8) - for ACL QoS entry. dhcpServerScreen(10) - for DHCP server screening entry. Note that only l2, l3v4 and l3v6 could be set by user, other is reserved for system to show information.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.2INTEGER {l2(1), l3v4(2), impb(3), arpSP_permit(4), arpSP_deny(5), voiceVlan(6), surveillanceVlan(7), aclQoS(8), dhcpServerScreen(10), l3v6(11), zone_defense(12)}read-writecurrent
aclProfileRuleCount
OBJECT-TYPE
The number of rules in this profile.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.3Integer32 (0..65535)read-onlycurrent
aclProfileMask
OBJECT-TYPE
Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 ARP-SP ARP_SENDER_MAC 14 ARP-SP ARP_SENDER_IP 15 (MSB) L3 TRAFFIC_CLASS 21 ------------------------------------------- The value is in Hex format.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.4OCTET STRINGread-writecurrent
aclProfileDstMacAddrMask
OBJECT-TYPE
The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.5MacAddressread-writecurrent
aclProfileSrcMacAddrMask
OBJECT-TYPE
The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.6MacAddressread-writecurrent
aclProfileIPProtocol
OBJECT-TYPE
Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.7INTEGER {none(0), icmp(1), igmp(2), tcp(6), udp(17), icmpv6(58)}read-writecurrent
aclProfileDstIpAddrMaskType
OBJECT-TYPE
IPv6 Address type.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.8INTEGER {iPv4(1), iPv6(2)}read-writecurrent
aclProfileDstIpAddrMask
OBJECT-TYPE
The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.7.15.1.2.1.9Ipv6Addressread-writecurrent
aclProfileSrcIpAddrMaskType
OBJECT-TYPE
IPv6 Address type.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.10INTEGER {iPv4(1), iPv6(2)}read-writecurrent
aclProfileSrcIpAddrMask
OBJECT-TYPE
The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.7.15.1.2.1.11Ipv6Addressread-writecurrent
aclProfileDstPortMask
OBJECT-TYPE
The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.12OCTET STRINGread-writecurrent
aclProfileSrcPortMask
OBJECT-TYPE
The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.13OCTET STRINGread-writecurrent
aclProfileArpSenderMacAddrMask
OBJECT-TYPE
The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.14MacAddressread-onlycurrent
aclProfileArpSenderIpAddrMask
OBJECT-TYPE
The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.15Ipv6Addressread-onlycurrent
aclProfileStatus
OBJECT-TYPE
This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.
1.3.6.1.4.1.171.10.75.7.15.1.2.1.16RowStatusread-createcurrent
aclL2Rule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.15.2
aclL2RuleTable
OBJECT-TYPE
A table to configure L2 filter rules in the system.
1.3.6.1.4.1.171.10.75.7.15.2.1not-accessiblecurrent
aclL2RuleEntry
OBJECT-TYPE
Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.
1.3.6.1.4.1.171.10.75.7.15.2.1.1not-accessiblecurrent
aclL2AccessID
OBJECT-TYPE
L2 Filter rule ID.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.1Integer32 (1..65535)read-onlycurrent
aclL2ProfileID
OBJECT-TYPE
ACL Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.2Integer32 (1..50)read-onlycurrent
aclL2RuleEtherType
OBJECT-TYPE
The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.3Integer32 (-1 | 1501..65535)read-writecurrent
aclL2RuleDstMacAddr
OBJECT-TYPE
Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.4MacAddressread-writecurrent
aclL2RuleSrcMacAddr
OBJECT-TYPE
Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address
1.3.6.1.4.1.171.10.75.7.15.2.1.1.5MacAddressread-writecurrent
aclL2RuleVlanId
OBJECT-TYPE
Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.6Integer32 (-1..4094)read-writecurrent
aclL2Rule1pPriority
OBJECT-TYPE
802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.7Integer32 (-1..7)read-writecurrent
aclL2RuleDstMacAddrMask
OBJECT-TYPE
The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.8MacAddressread-onlycurrent
aclL2RuleSrcMacAddrMask
OBJECT-TYPE
The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.9MacAddressread-onlycurrent
aclL2RuleInPortList
OBJECT-TYPE
Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.10PortListread-writecurrent
aclL2RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.11INTEGER {allow(1), drop(2)}read-writecurrent
aclL2RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.7.15.2.1.1.13RowStatusread-createcurrent
aclL3Rule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.15.3
aclL3RuleTable
OBJECT-TYPE
A table to configure L3 filter rules in the system.
1.3.6.1.4.1.171.10.75.7.15.3.1not-accessiblecurrent
aclL3RuleEntry
OBJECT-TYPE
Each entry in this table is a L3 filter rule. Index to the table is L3 filter number.
1.3.6.1.4.1.171.10.75.7.15.3.1.1not-accessiblecurrent
aclL3RuleAccessID
OBJECT-TYPE
L3 Filter rule ID.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.1Integer32 (1..65535)read-onlycurrent
aclL3RuleProfileNo
OBJECT-TYPE
The Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.2Integer32 (1..50)read-onlycurrent
aclL3RuleProtocol
OBJECT-TYPE
The type of protocol to be checked against the packet.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.3INTEGER {icmp(1), igmp(2), tcp(6), udp(17)}read-onlycurrent
aclL3RuleICMPMessageType
OBJECT-TYPE
The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),
1.3.6.1.4.1.171.10.75.7.15.3.1.1.4Integer32 (-1..255)read-writecurrent
aclL3RuleICMPMessageCode
OBJECT-TYPE
The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),
1.3.6.1.4.1.171.10.75.7.15.3.1.1.5Integer32 (-1..255)read-writecurrent
aclL3RuleDstIpAddr
OBJECT-TYPE
Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.6IpAddressread-writecurrent
aclL3RuleSrcIpAddr
OBJECT-TYPE
Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.7IpAddressread-writecurrent
aclL3RuleDstIpAddrMask
OBJECT-TYPE
The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.8IpAddressread-onlycurrent
aclL3RuleSrcIpAddrMask
OBJECT-TYPE
The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.9IpAddressread-onlycurrent
aclL3RuleTcpUdpDstPort
OBJECT-TYPE
The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.10Integer32 (-1..65535)read-writecurrent
aclL3RuleTcpUdpSrcPort
OBJECT-TYPE
The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.11Integer32 (-1..65535)read-writecurrent
aclL3RuleTcpUdpDstPortMask
OBJECT-TYPE
The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.12OCTET STRINGread-onlycurrent
aclL3RuleTcpUdpSrcPortMask
OBJECT-TYPE
The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.13OCTET STRINGread-onlycurrent
aclL3RuleTcpAckBit
OBJECT-TYPE
The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.14INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpRstBit
OBJECT-TYPE
The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.15INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpUrgBit
OBJECT-TYPE
The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.16INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpPshBit
OBJECT-TYPE
The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.17INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpSynBit
OBJECT-TYPE
The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.18INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpFinBit
OBJECT-TYPE
The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.19INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleDscp
OBJECT-TYPE
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.20Integer32 (-1..63)read-createcurrent
aclL3RuleIgmpType
OBJECT-TYPE
The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.21Integer32 (-1..255)read-writecurrent
aclL3RulePortList
OBJECT-TYPE
Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.22PortListread-writecurrent
aclL3RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.23INTEGER {allow(1), drop(2)}read-writecurrent
aclL3RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.7.15.3.1.1.25RowStatusread-createcurrent
aclv6L3RuleTable
OBJECT-TYPE
A table to configure L3 filter rules in the system.
1.3.6.1.4.1.171.10.75.7.15.3.2not-accessiblecurrent
aclv6L3RuleEntry
OBJECT-TYPE
Each entry in this table is a L3 filter rule. Index to the table is L3 filter number.
1.3.6.1.4.1.171.10.75.7.15.3.2.1not-accessiblecurrent
aclv6L3RuleAccessID
OBJECT-TYPE
L3 Filter rule ID.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.1Integer32 (1..65535)read-onlycurrent
aclv6L3RuleProfileNo
OBJECT-TYPE
The Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.2Integer32 (1..50)read-onlycurrent
aclv6L3RuleProtocol
OBJECT-TYPE
The type of protocol to be checked against the packet.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.3INTEGER {icmp(1), tcp(6), udp(17)}read-onlycurrent
aclv6L3RuleICMPMessageType
OBJECT-TYPE
The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),
1.3.6.1.4.1.171.10.75.7.15.3.2.1.4Integer32 (-1..255)read-writecurrent
aclv6L3RuleICMPMessageCode
OBJECT-TYPE
The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),
1.3.6.1.4.1.171.10.75.7.15.3.2.1.5Integer32 (-1..255)read-writecurrent
aclv6L3RuleDstIpAddr
OBJECT-TYPE
Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.6Ipv6Addressread-writecurrent
aclv6L3RuleSrcIpAddr
OBJECT-TYPE
Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.7Ipv6Addressread-writecurrent
aclv6L3RuleDstIpAddrMask
OBJECT-TYPE
The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.8Ipv6Addressread-onlycurrent
aclv6L3RuleSrcIpAddrMask
OBJECT-TYPE
The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.9Ipv6Addressread-onlycurrent
aclv6L3RuleTcpUdpDstPort
OBJECT-TYPE
The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.10Integer32 (-1..65535)read-writecurrent
aclv6L3RuleTcpUdpSrcPort
OBJECT-TYPE
The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.11Integer32 (-1..65535)read-writecurrent
aclv6L3RuleTcpUdpDstPortMask
OBJECT-TYPE
The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.12OCTET STRINGread-onlycurrent
aclv6L3RuleTcpUdpSrcPortMask
OBJECT-TYPE
The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.13OCTET STRINGread-onlycurrent
aclv6L3RuleTcpAckBit
OBJECT-TYPE
The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.14INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpRstBit
OBJECT-TYPE
The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.15INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpUrgBit
OBJECT-TYPE
The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.16INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpPshBit
OBJECT-TYPE
The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.17INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpSynBit
OBJECT-TYPE
The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.18INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpFinBit
OBJECT-TYPE
The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.19INTEGER {dont_care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTrafficClass
OBJECT-TYPE
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.20Integer32 (-1..63)read-createcurrent
aclv6L3RulePortList
OBJECT-TYPE
Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.21PortListread-writecurrent
aclv6L3RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.22INTEGER {allow(1), drop(2)}read-writecurrent
aclv6L3RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.7.15.3.2.1.24RowStatusread-createcurrent
companySyslog
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.16
ipv4syslogGeneralGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.16.1
ipv4syslogLogSrvAddr
OBJECT-TYPE
Specifies the syslog server IP to be used for remote logging. When configured, a new socket will be opened for this address. When the address is changed, the socket opened for the previous address will be closed and a new socket will be opened for this address.
1.3.6.1.4.1.171.10.75.7.16.1.1IpAddressread-writeobsolete
ipv4syslogUDPPort
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.7.16.1.2INTEGER (1..65535)read-writeobsolete
ipv4syslogTimeStamp
OBJECT-TYPE
This object is for enabling or disabling timestamp option. When enabled, the messages (log and email alert messages) will hold the time stamp information. When disabled, the time stamp information will not be carried with the messages sent to the log and mail servers.
1.3.6.1.4.1.171.10.75.7.16.1.3INTEGER {enable(1), disable(2)}read-writeobsolete
ipv4syslogSeverity
OBJECT-TYPE
Specifies the log level option to be set for a specific module.
1.3.6.1.4.1.171.10.75.7.16.1.4INTEGER {warning(4), info(6), all(7)}read-writeobsolete
ipv4syslogFacility
OBJECT-TYPE
The Syslog standard facilities. The facility to be used when sending Syslog messages to this server.
1.3.6.1.4.1.171.10.75.7.16.1.5INTEGER {local0(128), local1(136), local2(144), local3(152), local4(160), local5(168), local6(176), local7(184)}read-writeobsolete
ipv4syslogLogging
OBJECT-TYPE
This object is for enabling or disabling syslog alert features in the system. System Logs record and manage events, as well as report errors and informational messages.
1.3.6.1.4.1.171.10.75.7.16.1.6INTEGER {enable(1), disable(2)}read-writeobsolete
syslogGeneralGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.16.2
syslogState
OBJECT-TYPE
This object is for enabling or disabling syslog alert features in the system. System Logs record and manage events, as well as report errors and informational messages.
1.3.6.1.4.1.171.10.75.7.16.2.1INTEGER {enable(1), disable(2)}read-writecurrent
syslogTimeStampOption
OBJECT-TYPE
This object is for enabling or disabling timestamp option. When enabled, the messages (log and email alert messages) will hold the time stamp information. When disabled, the time stamp information will not be carried with the messages sent to the log and mail servers.
1.3.6.1.4.1.171.10.75.7.16.2.2INTEGER {enable(1), disable(2)}read-writecurrent
syslogSrvSeverity
OBJECT-TYPE
Specifies the log level option to be set for a specific module.
1.3.6.1.4.1.171.10.75.7.16.2.3INTEGER {warning(4), info(6), all(7)}read-writecurrent
syslogSrvFacility
OBJECT-TYPE
The Syslog standard facilities. The facility to be used when sending Syslog messages to this server.
1.3.6.1.4.1.171.10.75.7.16.2.4INTEGER {local0(128), local1(136), local2(144), local3(152), local4(160), local5(168), local6(176), local7(184)}read-writecurrent
syslogSrvTable
OBJECT-TYPE
A table containing entries of priority,server address type, server address, port through which it can send and tranport type.
1.3.6.1.4.1.171.10.75.7.16.2.5not-accessiblecurrent
syslogSrvEntry
OBJECT-TYPE
A table containing index as priority , server address type and server address.
1.3.6.1.4.1.171.10.75.7.16.2.5.1not-accessiblecurrent
syslogSrvIPType
OBJECT-TYPE
Specifies the Address type of server.Address type shall be ipv4 or ipv6.
1.3.6.1.4.1.171.10.75.7.16.2.5.1.1INTEGER {ipv4(1), ipv6(2)}read-onlycurrent
syslogSrvIP
OBJECT-TYPE
Specifies the ServerIP to which the syslog shall be forwarded.
1.3.6.1.4.1.171.10.75.7.16.2.5.1.2Ipv6Addressread-onlycurrent
syslogSrvPort
OBJECT-TYPE
Specifies the Port through which it can send the syslog message. By default the the port is 514
1.3.6.1.4.1.171.10.75.7.16.2.5.1.3Integer32 (0..65535)read-createcurrent
syslogInterfaceName
OBJECT-TYPE
Specifies the interface name when the syslogSrvIP is linklocal address.
1.3.6.1.4.1.171.10.75.7.16.2.5.1.4OCTET STRINGread-createcurrent
syslogSrvRowStatus
OBJECT-TYPE
The Status of the Server Entry.
1.3.6.1.4.1.171.10.75.7.16.2.5.1.5RowStatusread-createcurrent
companyLBD
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.17
sysLBDStateEnable
OBJECT-TYPE
Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator.
1.3.6.1.4.1.171.10.75.7.17.1INTEGER {enabled(1), disabled(2)}read-writecurrent
sysLBDMode
OBJECT-TYPE
Loopback detection function mode.
1.3.6.1.4.1.171.10.75.7.17.2INTEGER {port(1), vlan(2)}read-writecurrent
sysLBDInterval
OBJECT-TYPE
Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically.
1.3.6.1.4.1.171.10.75.7.17.3Integer32 (1..32767)read-writecurrent
sysLBDRecoverTime
OBJECT-TYPE
This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds.
1.3.6.1.4.1.171.10.75.7.17.4Integer32 (0 | 60..1000000)read-writecurrent
sysLBDCtrlTable
OBJECT-TYPE
A table to control Loopback detection features either for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.7.17.5not-accessiblecurrent
sysLBDCtrlEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.7.17.5.1not-accessiblecurrent
sysLBDCtrlIndex
OBJECT-TYPE
The interface index of the port for which the configuration in this entry applies.
1.3.6.1.4.1.171.10.75.7.17.5.1.1Integer32read-onlycurrent
sysLBDPortStatus
OBJECT-TYPE
Provides control to per port enable or disable the loopback detection function. Default is disabled.
1.3.6.1.4.1.171.10.75.7.17.5.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
sysLBDPortLoopStatus
OBJECT-TYPE
The loop status for this port.
1.3.6.1.4.1.171.10.75.7.17.5.1.3INTEGER {normal(1), disabled(2)}read-onlycurrent
sysLBDVlanLoopTable
OBJECT-TYPE
A table to display Loopback detection features by vlan mode .
1.3.6.1.4.1.171.10.75.7.17.6not-accessiblecurrent
sysLBDVlanLoopEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.7.17.6.1not-accessiblecurrent
sysLBDVlanLoopIndex
OBJECT-TYPE
Display port lists loop status by vlan.
1.3.6.1.4.1.171.10.75.7.17.6.1.1Integer32read-onlycurrent
sysLBDVlanLoopPorts
OBJECT-TYPE
Display port lists loop status by vlan.
1.3.6.1.4.1.171.10.75.7.17.6.1.2PortListread-onlycurrent
companyMirror
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.18
sysMirrorStatus
OBJECT-TYPE
Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied.
1.3.6.1.4.1.171.10.75.7.18.1INTEGER {enabled(1), disabled(2)}read-writecurrent
sysMirrorTargetPort
OBJECT-TYPE
Specifies the port to which the mirrored traffic in the system is to be copied.
1.3.6.1.4.1.171.10.75.7.18.2Integer32read-writecurrent
sysMirrorCtrlIngressMirroring
OBJECT-TYPE
Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.
1.3.6.1.4.1.171.10.75.7.18.3PortListread-writecurrent
sysMirrorCtrlEgressMirroring
OBJECT-TYPE
Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.
1.3.6.1.4.1.171.10.75.7.18.4PortListread-writecurrent
companyTrapSetting
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.19
sysTrapIP
OBJECT-TYPE
The smart console utility's IP address is used to recive trap events.
1.3.6.1.4.1.171.10.75.7.19.1IpAddressread-writecurrent
sysTrapSystemEvent
OBJECT-TYPE
Enable/Disable system trap events in the switch system.
1.3.6.1.4.1.171.10.75.7.19.2INTEGER {none(0), deviceBootUp(1), illegalLogin(2), both(3)}read-writecurrent
sysTrapPortEvent
OBJECT-TYPE
Enable/Disable port trap event in the system.
1.3.6.1.4.1.171.10.75.7.19.3INTEGER {enable(1), disable(2)}read-writecurrent
sysTrapStateChangeEvent
OBJECT-TYPE
Enable/Disable RSTP state change trap event in the system.
1.3.6.1.4.1.171.10.75.7.19.4INTEGER {enable(1), disable(2)}read-writecurrent
sysTrapFirmUpgradeEvent
OBJECT-TYPE
Enable/Disable firmware upgrading trap event in the system.
1.3.6.1.4.1.171.10.75.7.19.5INTEGER {enable(1), disable(2)}read-writecurrent
sysTrapStatus
OBJECT-TYPE
Enable/Disable trap event in the system.
1.3.6.1.4.1.171.10.75.7.19.11INTEGER {enable(1), disable(2)}read-writecurrent
companySNTPSetting
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.20
ipv4sysSNTPTimeSeconds
OBJECT-TYPE
This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037).
1.3.6.1.4.1.171.10.75.7.20.1Integer32read-writeobsolete
ipv4sysSNTPFirstServer
OBJECT-TYPE
SNTP First Server's IP Address
1.3.6.1.4.1.171.10.75.7.20.2IpAddressread-writeobsolete
ipv4sysSNTPSecondServer
OBJECT-TYPE
SNTP Second Server's IP Address
1.3.6.1.4.1.171.10.75.7.20.3IpAddressread-writeobsolete
ipv4sysSNTPPollInterval
OBJECT-TYPE
SNTP Poll Interval In Seconds (30-99999)
1.3.6.1.4.1.171.10.75.7.20.4Integer32read-writeobsolete
ipv4sysSNTPState
OBJECT-TYPE
Enable/Disable SNTP function in the system.
1.3.6.1.4.1.171.10.75.7.20.5INTEGER {sntp(1), local(2)}read-writeobsolete
ipv4sysSNTPDSTOffset
OBJECT-TYPE
This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes.
1.3.6.1.4.1.171.10.75.7.20.6INTEGER {offset30min(30), offset60min(60), offset90min(90), offset120min(120)}read-writeobsolete
ipv4sysSNTPGMTMinutes
OBJECT-TYPE
Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)
1.3.6.1.4.1.171.10.75.7.20.7INTEGERread-writeobsolete
ipv4sysSNTPDSTStartMon
OBJECT-TYPE
The start month of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.8INTEGERread-writeobsolete
ipv4sysSNTPDSTStartDay
OBJECT-TYPE
The start day of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.9INTEGERread-writeobsolete
ipv4sysSNTPDSTStartHour
OBJECT-TYPE
The start hour of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.10INTEGERread-writeobsolete
ipv4sysSNTPDSTStartMin
OBJECT-TYPE
The start minute of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.11INTEGERread-writeobsolete
ipv4sysSNTPDSTEndMon
OBJECT-TYPE
The end month of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.12INTEGERread-writeobsolete
ipv4sysSNTPDSTEndDay
OBJECT-TYPE
The end day of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.13INTEGERread-writeobsolete
ipv4sysSNTPDSTEndHour
OBJECT-TYPE
The end hour of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.14INTEGERread-writeobsolete
ipv4sysSNTPDSTEndMin
OBJECT-TYPE
The end minute of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.15INTEGERread-writeobsolete
ipv4sysSNTPDSTState
OBJECT-TYPE
This object is for Annual(1) or Disabled(2) DST state in the system.
1.3.6.1.4.1.171.10.75.7.20.16INTEGER {annual(1), disabled(2)}read-writeobsolete
sysSNTPServerTable
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.20.17
sysSNTPTimeSeconds
OBJECT-TYPE
This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037).
1.3.6.1.4.1.171.10.75.7.20.17.1Integer32read-writecurrent
sysSNTPFirstServer
OBJECT-TYPE
SNTP First Server's IPv6 Address
1.3.6.1.4.1.171.10.75.7.20.17.2Ipv6Addressread-writecurrent
sysSNTPFirstType
OBJECT-TYPE
SNTP First Server's IPv6 Address type.
1.3.6.1.4.1.171.10.75.7.20.17.3INTEGER {iPv4(1), iPv6(2)}read-writecurrent
sysSNTPFirstInterfaceName
OBJECT-TYPE
Specifies the interface name when the sysSNTPFirstServer is linklocal address.
1.3.6.1.4.1.171.10.75.7.20.17.4OCTET STRINGread-writecurrent
sysSNTPSecondServer
OBJECT-TYPE
SNTP Second Server's IPv6 Address
1.3.6.1.4.1.171.10.75.7.20.17.5Ipv6Addressread-writecurrent
sysSNTPSecondType
OBJECT-TYPE
SNTP First Server's IPv6 Address type.
1.3.6.1.4.1.171.10.75.7.20.17.6INTEGER {iPv4(1), iPv6(2)}read-writecurrent
sysSNTPSecondInterfaceName
OBJECT-TYPE
Specifies the interface name when the sysSNTPSecondServer is linklocal address.
1.3.6.1.4.1.171.10.75.7.20.17.7OCTET STRINGread-writecurrent
sysSNTPPollInterval
OBJECT-TYPE
SNTP Poll Interval In Seconds (30-99999)
1.3.6.1.4.1.171.10.75.7.20.17.8Integer32read-writecurrent
sysSNTPState
OBJECT-TYPE
Enable/Disable SNTP function in the system.
1.3.6.1.4.1.171.10.75.7.20.17.9INTEGER {sntp(1), local(2)}read-writecurrent
sysSNTPDSTOffset
OBJECT-TYPE
This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes.
1.3.6.1.4.1.171.10.75.7.20.17.10INTEGER {offset30min(30), offset60min(60), offset90min(90), offset120min(120)}read-writecurrent
sysSNTPGMTMinutes
OBJECT-TYPE
Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)
1.3.6.1.4.1.171.10.75.7.20.17.11INTEGERread-writecurrent
sysSNTPDSTStartMon
OBJECT-TYPE
The start month of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.17.12INTEGERread-writecurrent
sysSNTPDSTStartDay
OBJECT-TYPE
The start day of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.17.13INTEGERread-writecurrent
sysSNTPDSTStartHour
OBJECT-TYPE
The start hour of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.17.14INTEGERread-writecurrent
sysSNTPDSTStartMin
OBJECT-TYPE
The start minute of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.17.15INTEGERread-writecurrent
sysSNTPDSTEndMon
OBJECT-TYPE
The end month of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.17.16INTEGERread-writecurrent
sysSNTPDSTEndDay
OBJECT-TYPE
The end day of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.17.17INTEGERread-writecurrent
sysSNTPDSTEndHour
OBJECT-TYPE
The end hour of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.17.18INTEGERread-writecurrent
sysSNTPDSTEndMin
OBJECT-TYPE
The end minute of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.7.20.17.19INTEGERread-writecurrent
sysSNTPDSTState
OBJECT-TYPE
This object is for Annual(1) or Disabled(2) DST state in the system.
1.3.6.1.4.1.171.10.75.7.20.17.20INTEGER {annual(1), disabled(2)}read-writecurrent
companyVoiceVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.21
voicevlanSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.21.1
voiceVlanMode
OBJECT-TYPE
Voice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP service. This object is for enabling or disabling Voice Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Voice VLAN can not be enabled.
1.3.6.1.4.1.171.10.75.7.21.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
voiceVlanId
OBJECT-TYPE
The ID of VLAN that you want the voice traffic to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.7.21.1.3INTEGERread-writecurrent
voiceVlanTimeout
OBJECT-TYPE
A period of time in hour to remove a port from voice VLAN if the port is an automatic VLAN member. The Timeout range is 1~120 hours. Default aging time is 1 hour.
1.3.6.1.4.1.171.10.75.7.21.1.4INTEGERread-writecurrent
voiceVlanPriority
OBJECT-TYPE
The 802.1p priority levels of the traffic in the Voice VLAN.
1.3.6.1.4.1.171.10.75.7.21.1.5INTEGER {highest(0), high(1), medium(2), low(3)}read-writecurrent
voicevlanPortControlTable
OBJECT-TYPE
A table that contains Voice Vlan Port Control configuration information.
1.3.6.1.4.1.171.10.75.7.21.1.6not-accessiblecurrent
voicevlanPortControlEntry
OBJECT-TYPE
A list of Voice Vlan Control configuration parameters for each Port on this device.
1.3.6.1.4.1.171.10.75.7.21.1.6.1not-accessiblecurrent
voicevlanPortControlIndex
OBJECT-TYPE
The voice vlan port index.
1.3.6.1.4.1.171.10.75.7.21.1.6.1.1InterfaceIndexread-onlycurrent
voicevlanPortAutoDetection
OBJECT-TYPE
This object is for enabling or disabling Voice Vlan Auto Detection in the port. If the auto detection is enable, switch will add this port to the voice VLAN automatically if it detects the device OUI matches the Telephony OUI. If the port is a static member of voice vlan or a LA member, it can not enable voice vlan auto detection.
1.3.6.1.4.1.171.10.75.7.21.1.6.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
voicevlanPortManuTagMode
OBJECT-TYPE
User assign per port tag/untag mode.
1.3.6.1.4.1.171.10.75.7.21.1.6.1.3INTEGER {tag(1), untag(2)}read-writecurrent
voicevlanPortCurrentTagMode
OBJECT-TYPE
Per port current tag/untag mode.
1.3.6.1.4.1.171.10.75.7.21.1.6.1.4INTEGER {tag(1), untag(2), none(3)}read-onlycurrent
voicevlanPortState
OBJECT-TYPE
This object indicates Voice vlan state to this Port. manual - this port is a static member of voice vlan. dynamic - this port is a dynamic member of voice vlan. none - this port is not a member of voice vlan.
1.3.6.1.4.1.171.10.75.7.21.1.6.1.5INTEGER {manual(1), dynamic(2), none(3)}read-onlycurrent
voicevlanOUI
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.21.2
voicevlanOUITable
OBJECT-TYPE
A voice vlan OUI entry containing the description and mac.
1.3.6.1.4.1.171.10.75.7.21.2.1not-accessiblecurrent
voicevlanOUIEntry
OBJECT-TYPE
A voice vlan OUI entry containing the description and mac.
1.3.6.1.4.1.171.10.75.7.21.2.1.1not-accessiblecurrent
voicevlanOUITelephonyOUI
OBJECT-TYPE
An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the voice traffic's OUI that user created.
1.3.6.1.4.1.171.10.75.7.21.2.1.1.1MacAddressread-onlycurrent
voicevlanOUIDescription
OBJECT-TYPE
The Description for the OUI.
1.3.6.1.4.1.171.10.75.7.21.2.1.1.2OCTET STRINGread-writecurrent
voicevlanOUIMask
OBJECT-TYPE
Voice vlan OUI Mask. Always be FF:FF:FF:00:00:00.
1.3.6.1.4.1.171.10.75.7.21.2.1.1.3MacAddressread-onlycurrent
voicevlanOUIStatus
OBJECT-TYPE
This object indicates the status of this entry. To create a new entry, you must set the voicevlanOUIStatus to be CreateAndGo, then this entry will turn to be Active.
1.3.6.1.4.1.171.10.75.7.21.2.1.1.4RowStatusread-writecurrent
voicevlanDevice
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.21.3
voicevlanDeviceTable
OBJECT-TYPE
A voice vlan Device entry containing the description and mac.
1.3.6.1.4.1.171.10.75.7.21.3.1not-accessiblecurrent
voicevlanDeviceEntry
OBJECT-TYPE
A voice vlan Device entry containing the description and mac.
1.3.6.1.4.1.171.10.75.7.21.3.1.1not-accessiblecurrent
voicevlanDeviceIndexMac
OBJECT-TYPE
An Mac Address is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the voice traffic's Mac that voice device created.
1.3.6.1.4.1.171.10.75.7.21.3.1.1.1MacAddressread-onlycurrent
voicevlanDevicePort
OBJECT-TYPE
The port is learning by voice device.
1.3.6.1.4.1.171.10.75.7.21.3.1.1.2INTEGERread-onlycurrent
voicevlanDevicePriority
OBJECT-TYPE
The priority value for voice device.
1.3.6.1.4.1.171.10.75.7.21.3.1.1.3INTEGERread-onlycurrent
voicevlanDeviceTagType
OBJECT-TYPE
The tag type for voice device.
1.3.6.1.4.1.171.10.75.7.21.3.1.1.4INTEGER {tag(1), untag(2)}read-onlycurrent
voicevlanDeviceStatus
OBJECT-TYPE
This object indicates the status of this entry. You can delete this object.
1.3.6.1.4.1.171.10.75.7.21.3.1.1.5INTEGER {active(1), destroy(6)}read-writecurrent
companyLLDPSetting
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.24
dlinklldpState
OBJECT-TYPE
This object is used for enabling or disabling LLDP in the system.
1.3.6.1.4.1.171.10.75.7.24.1INTEGER {enable(1), disable(2)}read-writecurrent
dlinklldpMsgHoldMultiplier
OBJECT-TYPE
The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpMessageTxInterval * lldpMessageTxHoldMultiplier))
1.3.6.1.4.1.171.10.75.7.24.2INTEGER (2..10)read-writecurrent
dlinklldpMsgTxInterval
OBJECT-TYPE
This object is used for LLDP packet update frequency. The timer in units of seconds.
1.3.6.1.4.1.171.10.75.7.24.3INTEGER (5..32768)read-writecurrent
dlinklldpReinitDelay
OBJECT-TYPE
This object is used for LLDP Reinitialization Delay. The timer in units of seconds.
1.3.6.1.4.1.171.10.75.7.24.4INTEGER (1..10)read-writecurrent
dlinklldpTxDelay
OBJECT-TYPE
The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB. The recommended value for the lldpTxDelay is set by the following formula: 1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval).
1.3.6.1.4.1.171.10.75.7.24.5INTEGER (1..8192)read-writecurrent
dlinklldpConfigManAddrTable
OBJECT-TYPE
The table that controls selection of LLDP management address TLV instances to be transmitted on individual ports.
1.3.6.1.4.1.171.10.75.7.24.7not-accessiblecurrent
dlinklldpConfigManAddrEntry
OBJECT-TYPE
LLDP configuration information that specifies the set of ports (represented as a PortList) on which the local system management address instance will be transmitted. This configuration object augments the lldpLocManAddrEntry, therefore it is only present along with the management address instance contained in the associated lldpLocManAddrEntry entry. Each active lldpConfigManAddrEntry must be restored from non-volatile and re-created (along with the corresponding lldpLocManAddrEntry) after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.7.24.7.1not-accessiblecurrent
dlinklldpLocManAddrSubtype
OBJECT-TYPE
The type of management address identifier encoding used in the associated 'lldpLocManagmentAddr' object.
1.3.6.1.4.1.171.10.75.7.24.7.1.1AddressFamilyNumbersread-onlycurrent
dlinklldpLocManAddr
OBJECT-TYPE
The string value used to identify the management address component associated with the local system. The purpose of this address is to contact the management entity.
1.3.6.1.4.1.171.10.75.7.24.7.1.2LldpManAddressread-onlycurrent
dlinklldpConfigManAddrPortsTxEnable
OBJECT-TYPE
A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will be transmitted on the member ports of the lldpManAddrPortsTxEnable. The default value for lldpConfigManAddrPortsTxEnable object is empty binary string, which means no ports are specified for advertising indicated management address instance.
1.3.6.1.4.1.171.10.75.7.24.7.1.3PortListread-writecurrent
companySNMPV3
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.25
snmpGlobalState
OBJECT-TYPE
This object is for enabling or disabling SNMP Community function.
1.3.6.1.4.1.171.10.75.7.25.1INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3User
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.25.2
snmpV3UserTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.2.1not-accessiblecurrent
snmpV3UserEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.2.1.1not-accessiblecurrent
snmpV3UserName
OBJECT-TYPE
A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.
1.3.6.1.4.1.171.10.75.7.25.2.1.1.1SnmpAdminString (SIZE(1..32))read-onlycurrent
snmpV3UserVersion
OBJECT-TYPE
A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.
1.3.6.1.4.1.171.10.75.7.25.2.1.1.2INTEGER {v1(1), v2c(2), v3(3)}read-onlycurrent
snmpV3UserGroupName
OBJECT-TYPE
The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.
1.3.6.1.4.1.171.10.75.7.25.2.1.1.3SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3UserAuthProtocol
OBJECT-TYPE
An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol.
1.3.6.1.4.1.171.10.75.7.25.2.1.1.4INTEGER {none(1), md5(2), sha(3)}read-createcurrent
snmpV3UserAuthProtocolPassword
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.2.1.1.5SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3UserPrivProtocol
OBJECT-TYPE
An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned.
1.3.6.1.4.1.171.10.75.7.25.2.1.1.6INTEGER {none(1), des(2)}read-createcurrent
snmpV3UserPrivProtocolPassword
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.2.1.1.7SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3UserStatus
OBJECT-TYPE
The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.
1.3.6.1.4.1.171.10.75.7.25.2.1.1.8RowStatusread-createcurrent
snmpV3Group
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.25.3
snmpV3GroupTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.3.1not-accessiblecurrent
snmpV3GroupEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.3.1.1not-accessiblecurrent
snmpV3GroupName
OBJECT-TYPE
The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.
1.3.6.1.4.1.171.10.75.7.25.3.1.1.1SnmpAdminString (SIZE(1..32))read-onlycurrent
snmpV3GroupSecurityModel
OBJECT-TYPE
In order to gain the access rights allowed by this conceptual row, this securityModel must be in use.
1.3.6.1.4.1.171.10.75.7.25.3.1.1.2INTEGER {v1(1), v2c(2), v3(3)}read-onlycurrent
snmpV3GroupSecurityLevel
OBJECT-TYPE
The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected.
1.3.6.1.4.1.171.10.75.7.25.3.1.1.3SnmpSecurityLevelread-onlycurrent
snmpV3GroupReadViewName
OBJECT-TYPE
The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
1.3.6.1.4.1.171.10.75.7.25.3.1.1.4SnmpAdminString (SIZE(0..32))read-createcurrent
snmpV3GroupWriteViewName
OBJECT-TYPE
The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
1.3.6.1.4.1.171.10.75.7.25.3.1.1.5SnmpAdminString (SIZE(0..32))read-createcurrent
snmpV3GroupNotifyViewName
OBJECT-TYPE
The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
1.3.6.1.4.1.171.10.75.7.25.3.1.1.6SnmpAdminString (SIZE(0..32))read-createcurrent
snmpV3GroupStatus
OBJECT-TYPE
The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.
1.3.6.1.4.1.171.10.75.7.25.3.1.1.7RowStatusread-createcurrent
snmpV3ViewTree
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.25.4
snmpV3ViewTreeTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.4.1not-accessiblecurrent
snmpV3ViewTreeEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.4.1.1not-accessiblecurrent
snmpV3viewTreeName
OBJECT-TYPE
The human readable name for a family of view subtrees.
1.3.6.1.4.1.171.10.75.7.25.4.1.1.1SnmpAdminString (SIZE(1..32))read-onlycurrent
snmpV3viewTreeSubtree
OBJECT-TYPE
The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees.
1.3.6.1.4.1.171.10.75.7.25.4.1.1.2OBJECT IDENTIFIERread-onlycurrent
snmpV3viewTreeMask
OBJECT-TYPE
The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only.
1.3.6.1.4.1.171.10.75.7.25.4.1.1.3OCTET STRING (SIZE(0..16))read-createcurrent
snmpV3viewTreeType
OBJECT-TYPE
Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view.
1.3.6.1.4.1.171.10.75.7.25.4.1.1.4INTEGER {included(1), excluded(2)}read-createcurrent
snmpV3viewTreeStatus
OBJECT-TYPE
The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.
1.3.6.1.4.1.171.10.75.7.25.4.1.1.5RowStatusread-createcurrent
snmpV3Community
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.25.5
snmpV3CommunityTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.5.1not-accessiblecurrent
snmpV3CommunityEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.5.1.1not-accessiblecurrent
snmpV3CommunityName
OBJECT-TYPE
The unique index value of a row in this table.
1.3.6.1.4.1.171.10.75.7.25.5.1.1.1OCTET STRINGread-onlycurrent
snmpV3CommunityPolicy
OBJECT-TYPE
A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format.
1.3.6.1.4.1.171.10.75.7.25.5.1.1.2SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3CommunityStatus
OBJECT-TYPE
The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1).
1.3.6.1.4.1.171.10.75.7.25.5.1.1.3RowStatusread-createcurrent
snmpV3Host
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.25.6
ipv4snmpV3HostTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.6.1not-accessibleobsolete
ipv4snmpV3HostEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.6.1.1not-accessibleobsolete
ipv4snmpV3HostAddress
OBJECT-TYPE
This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.
1.3.6.1.4.1.171.10.75.7.25.6.1.1.1IpAddressread-onlyobsolete
ipv4snmpV3HostCommunityName
OBJECT-TYPE
The locally arbitrary.
1.3.6.1.4.1.171.10.75.7.25.6.1.1.2SnmpAdminString (SIZE(1..32))read-createobsolete
ipv4snmpV3HostVersion
OBJECT-TYPE
The Level of Security to be used when generating SNMP messages using this entry.
1.3.6.1.4.1.171.10.75.7.25.6.1.1.3INTEGER {v1(1), v2c(2), v3NoAuthNoPriv(3), v3AuthNoPriv(4), v3AuthPriv(5)}read-createobsolete
ipv4snmpV3HostStatus
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.6.1.1.4RowStatusread-createobsolete
snmpV3HostTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.6.2not-accessiblecurrent
snmpV3HostEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.6.2.1not-accessiblecurrent
snmpV3HostAddress
OBJECT-TYPE
This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.
1.3.6.1.4.1.171.10.75.7.25.6.2.1.1Ipv6Addressread-onlycurrent
snmpV3IPType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.7.25.6.2.1.2INTEGER {iPv4(1), iPv6(2)}read-onlycurrent
snmpV3HostCommunityName
OBJECT-TYPE
The locally arbitrary.
1.3.6.1.4.1.171.10.75.7.25.6.2.1.3SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3HostVersion
OBJECT-TYPE
The Level of Security to be used when generating SNMP messages using this entry.
1.3.6.1.4.1.171.10.75.7.25.6.2.1.4INTEGER {v1(1), v2c(2), v3NoAuthNoPriv(3), v3AuthNoPriv(4), v3AuthPriv(5)}read-createcurrent
snmpV3HostInterfaceName
OBJECT-TYPE
Specifies the interface name when the syslogSrvIP is linklocal address.
1.3.6.1.4.1.171.10.75.7.25.6.2.1.5OCTET STRINGread-createcurrent
snmpV3HostStatus
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.7.25.6.2.1.6RowStatusread-createcurrent
snmpV3EngineID
OBJECT-TYPE
An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate.
1.3.6.1.4.1.171.10.75.7.25.7SnmpEngineIDread-writecurrent
snmpV3Trap
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.25.8
snmpV3TrapSNMPAuthentication
OBJECT-TYPE
This object is for enabling or disabling SNMP login fail event trap in the system.
1.3.6.1.4.1.171.10.75.7.25.8.1INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapBootup
OBJECT-TYPE
This object is for enabling or disabling devie Bootup event trap in the system.
1.3.6.1.4.1.171.10.75.7.25.8.2INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapPortLinkUpDown
OBJECT-TYPE
This object is for enabling or disabling Port link up / link down event trap in the system.
1.3.6.1.4.1.171.10.75.7.25.8.3INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapRSTPStateChange
OBJECT-TYPE
This object is for enabling or disabling RSTP topology change event trap in the system.
1.3.6.1.4.1.171.10.75.7.25.8.4INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapFirmUpgrade
OBJECT-TYPE
This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system.
1.3.6.1.4.1.171.10.75.7.25.8.5INTEGER {enabled(1), disabled(2)}read-writecurrent
companyAutoSurveillanceVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.26
autoSurveillanceVlanSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.26.1
autoSurveillanceVlanMode
OBJECT-TYPE
This object is for enabling or disabling Auto Surveillance Vlan function in the system. If the Vlan mode is in Asymmetric VLAN mode, Auto Surveillance VLAN can not be enabled.
1.3.6.1.4.1.171.10.75.7.26.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
autoSurveillanceVlanId
OBJECT-TYPE
The ID of VLAN that you want the surveillance traffic to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.7.26.1.2INTEGERread-writecurrent
autoSurveillanceVlanPriority
OBJECT-TYPE
The 802.1p priority levels of the traffic in the Auto Surveillance VLAN.
1.3.6.1.4.1.171.10.75.7.26.1.3INTEGER {highest(0), high(1), medium(2), low(3)}read-writecurrent
autoSurveillanceVlanTaggedUplinkDownlinkPort
OBJECT-TYPE
Auto Surveillance vlan uplink ports can't auto learning OUI.
1.3.6.1.4.1.171.10.75.7.26.1.4PortListread-writecurrent
autoSurveillanceVlanOUI
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.26.2
autoSurveillanceVlanOUITable
OBJECT-TYPE
A Auto Surveillance vlan OUI entry containing the description and mac.
1.3.6.1.4.1.171.10.75.7.26.2.1not-accessiblecurrent
autoSurveillanceVlanOUIEntry
OBJECT-TYPE
A Auto Surveillance vlan OUI entry containing the description and mac.
1.3.6.1.4.1.171.10.75.7.26.2.1.1not-accessiblecurrent
autoSurveillanceVlanOUISurveillanceOUI
OBJECT-TYPE
An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object indicates the surveillance traffic's OUI that user created.
1.3.6.1.4.1.171.10.75.7.26.2.1.1.1MacAddressread-onlycurrent
autoSurveillanceVlanOUIDescription
OBJECT-TYPE
The Description for the OUI.
1.3.6.1.4.1.171.10.75.7.26.2.1.1.2OCTET STRINGread-writecurrent
autoSurveillanceVlanOUIMask
OBJECT-TYPE
Auto Surveillance vlan OUI Mask. The default OUI Mask is FF:FF:FF:F0:00:00. And default OUI Mask is read-only. In user define OUI's Mask is FF:FF:FF:00:00:00, in user define MAC's Mask is FF:FF:FF:FF:FF:FF.
1.3.6.1.4.1.171.10.75.7.26.2.1.1.3MacAddressread-writecurrent
autoSurveillanceVlanOUIComponentType
OBJECT-TYPE
This object indicates the Component Type of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIComponentType to be CreateAndGo, then this entry will turn to be Active.
1.3.6.1.4.1.171.10.75.7.26.2.1.1.4INTEGER {video_Management_Server(0), vMS_Client(1), video_Encoder(2), network_Storage(3), other_IP_Surveillance_Devices(4), d-Link_Surveillance_Device(5)}read-writecurrent
autoSurveillanceVlanOUIStatus
OBJECT-TYPE
This object indicates the status of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIStatus to be CreateAndGo, then this entry will turn to be Active.
1.3.6.1.4.1.171.10.75.7.26.2.1.1.5RowStatusread-writecurrent
companyTraps
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.27
traps
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.27.0
companyGreenSetting
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.31
dlinkGreenLEDShutoff
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.31.1
dlinkGreenLEDShutoffPortList
OBJECT-TYPE
Provides control to disable LED port.
1.3.6.1.4.1.171.10.75.7.31.1.1PortListread-writecurrent
dlinkGreenLEDShutoffState
OBJECT-TYPE
Enable/Disable Green disable LED function. Default is disabled.
1.3.6.1.4.1.171.10.75.7.31.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
dlinkGreenLEDShutoffTimeProfile1
OBJECT-TYPE
The time profile name associated with the Schedule entry (e.g., `abc, bbb').
1.3.6.1.4.1.171.10.75.7.31.1.3DisplayString (SIZE(1..20))read-writecurrent
dlinkGreenLEDShutoffTimeProfile2
OBJECT-TYPE
The time profile name associated with the Schedule entry (e.g., `abc, bbb').
1.3.6.1.4.1.171.10.75.7.31.1.4DisplayString (SIZE(1..20))read-writecurrent
dlinkGreenPortShutoff
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.31.2
dlinkGreenPortShutoffPortList
OBJECT-TYPE
Provides control to disable LED port.
1.3.6.1.4.1.171.10.75.7.31.2.1PortListread-writecurrent
dlinkGreenPortShutoffState
OBJECT-TYPE
Enable/Disable Green disable LED function. Default is disabled.
1.3.6.1.4.1.171.10.75.7.31.2.2INTEGER {disabled(0), enabled(1)}read-writecurrent
dlinkGreenPortShutoffTimeProfile1
OBJECT-TYPE
The time profile name associated with the Schedule entry (e.g., `abc, bbb').
1.3.6.1.4.1.171.10.75.7.31.2.3DisplayString (SIZE(1..20))read-writecurrent
dlinkGreenPortShutoffTimeProfile2
OBJECT-TYPE
The time profile name associated with the Schedule entry (e.g., `abc, bbb').
1.3.6.1.4.1.171.10.75.7.31.2.4DisplayString (SIZE(1..20))read-writecurrent
dlinkGreenSystemHibernation
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.31.4
dlinkGreenSystemHibernationState
OBJECT-TYPE
Enable/Disable Green disable LED function. Default is disabled.
1.3.6.1.4.1.171.10.75.7.31.4.1INTEGER {disabled(0), enabled(1)}read-writecurrent
dlinkGreenSystemHibernationTimeProfile1
OBJECT-TYPE
The time profile name associated with the Schedule entry (e.g., `abc, bbb').
1.3.6.1.4.1.171.10.75.7.31.4.2DisplayString (SIZE(1..20))read-writecurrent
dlinkGreenSystemHibernationTimeProfile2
OBJECT-TYPE
The time profile name associated with the Schedule entry (e.g., `abc, bbb').
1.3.6.1.4.1.171.10.75.7.31.4.3DisplayString (SIZE(1..20))read-writecurrent
companyTimeRangeMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.32
swTimeRangeSettingTable
OBJECT-TYPE
A table to configure time Range in the system.
1.3.6.1.4.1.171.10.75.7.32.1not-accessiblecurrent
swTimeRangeSettingEntry
OBJECT-TYPE
A schedule entry to configure time Range in the system.
1.3.6.1.4.1.171.10.75.7.32.1.1not-accessiblecurrent
swTimeRangeIndex
OBJECT-TYPE
The Time Range identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 52.
1.3.6.1.4.1.171.10.75.7.32.1.1.1Integer32 (1..52)read-onlycurrent
swTimeRangeName
OBJECT-TYPE
The Schedule name associated with the Schedule entry (e.g., `abc, bbb').
1.3.6.1.4.1.171.10.75.7.32.1.1.2DisplayString (SIZE(1..20))read-writecurrent
swTimeRangeDate
OBJECT-TYPE
Enable/Disable date range checking while executing time base PoE.
1.3.6.1.4.1.171.10.75.7.32.1.1.3INTEGER {enabled(1), disabled(2)}read-writecurrent
swTimeRangeStartYear
OBJECT-TYPE
Start year of the Schedule entry.
1.3.6.1.4.1.171.10.75.7.32.1.1.4INTEGER {y2009(2009), y2010(2010), y2011(2011), y2012(2012), y2013(2013), y2014(2014), y2015(2015), y2016(2016), y2017(2017), y2018(2018), y2019(2019), y2020(2020), y2021(2021), y2022(2022), y2023(2023), y2024(2024), y2025(2025), y2026(2026), y2027(2027), y2028(2028), y2029(2029), y2030(2030), y2031(2031), y2032(2032), y2033(2033), y2034(2034), y2035(2035), y2036(2036), y2037(2037)}read-writecurrent
swTimeRangeStartMonth
OBJECT-TYPE
Start month of the Schedule entry.
1.3.6.1.4.1.171.10.75.7.32.1.1.5INTEGER {january(1), february(2), march(3), april(4), may(5), june(6), july(7), august(8), september(9), october(10), november(11), december(12)}read-writecurrent
swTimeRangeStartDay
OBJECT-TYPE
Start day of the Schedule entry. The value must be from 1 to 31.
1.3.6.1.4.1.171.10.75.7.32.1.1.6Integer32 (1..31)read-writecurrent
swTimeRangeStartHour
OBJECT-TYPE
Start hour of the Schedule entry. The value must be from 0 to 23.
1.3.6.1.4.1.171.10.75.7.32.1.1.7Integer32 (0..23)read-writecurrent
swTimeRangeStartMinute
OBJECT-TYPE
Start minute of the Schedule entry. The value must be from 0 to 59.
1.3.6.1.4.1.171.10.75.7.32.1.1.8Integer32 (0..59)read-writecurrent
swTimeRangeEndYear
OBJECT-TYPE
End year of the Schedule entry.
1.3.6.1.4.1.171.10.75.7.32.1.1.9INTEGER {y2009(2009), y2010(2010), y2011(2011), y2012(2012), y2013(2013), y2014(2014), y2015(2015), y2016(2016), y2017(2017), y2018(2018), y2019(2019), y2020(2020), y2021(2021), y2022(2022), y2023(2023), y2024(2024), y2025(2025), y2026(2026), y2027(2027), y2028(2028), y2029(2029), y2030(2030), y2031(2031), y2032(2032), y2033(2033), y2034(2034), y2035(2035), y2036(2036), y2037(2037)}read-writecurrent
swTimeRangeEndMonth
OBJECT-TYPE
End month of the Schedule entry.
1.3.6.1.4.1.171.10.75.7.32.1.1.10INTEGER {january(1), february(2), march(3), april(4), may(5), june(6), july(7), august(8), september(9), october(10), november(11), december(12)}read-writecurrent
swTimeRangeEndDay
OBJECT-TYPE
End day of the Schedule entry. The value must be from 1 to 31.
1.3.6.1.4.1.171.10.75.7.32.1.1.11Integer32 (1..31)read-writecurrent
swTimeRangeEndHour
OBJECT-TYPE
End hour of the Schedule entry. The value must be from 0 to 23.
1.3.6.1.4.1.171.10.75.7.32.1.1.12Integer32 (0..23)read-writecurrent
swTimeRangeEndMinute
OBJECT-TYPE
End minute of the Schedule entry. The value must be from 0 to 59.
1.3.6.1.4.1.171.10.75.7.32.1.1.13Integer32 (0..59)read-writecurrent
swTimeRangeMonday
OBJECT-TYPE
Enable/Disble scheduling Monday.
1.3.6.1.4.1.171.10.75.7.32.1.1.14INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeTuesday
OBJECT-TYPE
Enable/Disble scheduling Tuesday.
1.3.6.1.4.1.171.10.75.7.32.1.1.15INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeWednesday
OBJECT-TYPE
Enable/Disble scheduling Wednesday.
1.3.6.1.4.1.171.10.75.7.32.1.1.16INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeThursday
OBJECT-TYPE
Enable/Disble scheduling Thursday.
1.3.6.1.4.1.171.10.75.7.32.1.1.17INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeFriday
OBJECT-TYPE
Enable/Disble scheduling Friday.
1.3.6.1.4.1.171.10.75.7.32.1.1.18INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeSaturday
OBJECT-TYPE
Enable/Disble scheduling Saturday.
1.3.6.1.4.1.171.10.75.7.32.1.1.19INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeSunday
OBJECT-TYPE
Enable/Disble scheduling Sunday.
1.3.6.1.4.1.171.10.75.7.32.1.1.20INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeRowStatus
OBJECT-TYPE
The status of an entry in the Time Range Information Table. Only a subset of the rowstatus variables (active, notinservice, createAndWait, destroy) are available.
1.3.6.1.4.1.171.10.75.7.32.1.1.21RowStatusread-createcurrent
companyStaticMcast
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.35
staticMcastTable
OBJECT-TYPE
A list of the Static MACs
1.3.6.1.4.1.171.10.75.7.35.1not-accessiblecurrent
staticMcastEntry
OBJECT-TYPE
A Static MAC entry containing the mac and forwarding port.
1.3.6.1.4.1.171.10.75.7.35.1.1not-accessiblecurrent
staticMcastVlanID
OBJECT-TYPE
The VLAN ID of the static MAC entry.
1.3.6.1.4.1.171.10.75.7.35.1.1.1INTEGERread-onlycurrent
staticMcastMac
OBJECT-TYPE
The MAC address associated of the static MAC entry.
1.3.6.1.4.1.171.10.75.7.35.1.1.2MacAddressread-onlycurrent
staticMcastEgressPorts
OBJECT-TYPE
The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.
1.3.6.1.4.1.171.10.75.7.35.1.1.3PortListread-onlycurrent
staticMcastStatus
OBJECT-TYPE
The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.7.35.1.1.4RowStatusread-writecurrent
companyCableDiagnostic
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.37
cableDiagTriggerIndex
OBJECT-TYPE
Trigger an interface index to do cable diagnostic.
1.3.6.1.4.1.171.10.75.7.37.1Integer32read-writecurrent
cableDiagPair1TestResult
OBJECT-TYPE
Cable diagnostics pair 1 test result.
1.3.6.1.4.1.171.10.75.7.37.2INTEGER {ok(0), open(1), short(2), notAvailable(5)}read-onlycurrent
cableDiagPair1FaultDistance
OBJECT-TYPE
Cable Diagnostics pair 1 fault distance.
1.3.6.1.4.1.171.10.75.7.37.3Integer32read-onlycurrent
cableDiagPair2TestResult
OBJECT-TYPE
Cable diagnostics pair 2 test result.
1.3.6.1.4.1.171.10.75.7.37.4INTEGER {ok(0), open(1), short(2), notAvailable(5)}read-onlycurrent
cableDiagPair2FaultDistance
OBJECT-TYPE
Cable diagnostics pair 2 fault distance.
1.3.6.1.4.1.171.10.75.7.37.5Integer32read-onlycurrent
cableDiagPair3TestResult
OBJECT-TYPE
Cable diagnostics pair 3 test result.
1.3.6.1.4.1.171.10.75.7.37.6INTEGER {ok(0), open(1), short(2), notAvailable(5)}read-onlycurrent
cableDiagPair3FaultDistance
OBJECT-TYPE
Cable diagnostics pair 3 fault distance.
1.3.6.1.4.1.171.10.75.7.37.7Integer32read-onlycurrent
cableDiagPair4TestResult
OBJECT-TYPE
Cable diagnostics pair 4 test result.
1.3.6.1.4.1.171.10.75.7.37.8INTEGER {ok(0), open(1), short(2), notAvailable(5)}read-onlycurrent
cableDiagPair4FaultDistance
OBJECT-TYPE
Cable diagnostics pair 4 fault distance.
1.3.6.1.4.1.171.10.75.7.37.9Integer32read-onlycurrent
cableDiagLengthinRange
OBJECT-TYPE
Cable diagnostics length when link up in speed 1G. (Display in range)
1.3.6.1.4.1.171.10.75.7.37.10INTEGER {less50(1), from50to80(2), from80to100(3), from100to140(4), notAvailable(5)}read-onlycurrent
companyRMON
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.47
rmonGlobalState
OBJECT-TYPE
This object is for enabling or disabling RMON function.
1.3.6.1.4.1.171.10.75.7.47.1INTEGER {enabled(1), disabled(2)}read-writecurrent
rmonStatistics
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.47.2
rmonStatsTable
OBJECT-TYPE
A list of Ethernet statistics entries.
1.3.6.1.4.1.171.10.75.7.47.2.1not-accessiblecurrent
rmonStatsEntry
OBJECT-TYPE
A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1
1.3.6.1.4.1.171.10.75.7.47.2.1.1not-accessiblecurrent
rmonStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this etherStats entry.
1.3.6.1.4.1.171.10.75.7.47.2.1.1.1Integer32 (1..65535)read-onlycurrent
rmonStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated etherStatsStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.2.1.1.2OBJECT IDENTIFIERread-createcurrent
rmonStatsOwner
OBJECT-TYPE
The entity that configured this entry and is therefore using the resources assigned to it.
1.3.6.1.4.1.171.10.75.7.47.2.1.1.3OCTET STRING (SIZE(1..32))read-createcurrent
rmonStatsStatus
OBJECT-TYPE
The status of this etherStats entry.
1.3.6.1.4.1.171.10.75.7.47.2.1.1.4RmonStatusread-createcurrent
rmonHistory
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.47.3
rmonHistoryTable
OBJECT-TYPE
A list of history control entries.
1.3.6.1.4.1.171.10.75.7.47.3.1not-accessiblecurrent
rmonHistoryEntry
OBJECT-TYPE
A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyControlInterval.2
1.3.6.1.4.1.171.10.75.7.47.3.1.1not-accessiblecurrent
rmonHistoryIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
1.3.6.1.4.1.171.10.75.7.47.3.1.1.1Integer32 (1..65535)read-onlycurrent
rmonHistoryDataSource
OBJECT-TYPE
This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.3.1.1.2OBJECT IDENTIFIERread-createcurrent
rmonHistoryBucketsRequested
OBJECT-TYPE
The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources.
1.3.6.1.4.1.171.10.75.7.47.3.1.1.3Integer32 (1..65535)read-createcurrent
rmonHistoryInterval
OBJECT-TYPE
The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.3.1.1.4Integer32 (1..3600)read-createcurrent
rmonHistoryOwner
OBJECT-TYPE
The entity that configured this entry and is therefore using the resources assigned to it.
1.3.6.1.4.1.171.10.75.7.47.3.1.1.5OCTET STRING (SIZE(1..32))read-createcurrent
rmonHistoryStatus
OBJECT-TYPE
The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.3.1.1.6RmonStatusread-createcurrent
rmonAlarm
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.47.4
rmonAlarmTable
OBJECT-TYPE
A list of alarm entries.
1.3.6.1.4.1.171.10.75.7.47.4.1not-accessiblecurrent
rmonAlarmEntry
OBJECT-TYPE
A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8
1.3.6.1.4.1.171.10.75.7.47.4.1.1not-accessiblecurrent
rmonAlarmIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device.
1.3.6.1.4.1.171.10.75.7.47.4.1.1.1Integer32 (1..65535)read-onlycurrent
rmonAlarmInterval
OBJECT-TYPE
The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be set short enough that the sampled variable is very unlikely to increase or decrease by more than 2^31 - 1 during a single sampling interval. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.4.1.1.2Integer32read-createcurrent
rmonAlarmVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.4.1.1.3OBJECT IDENTIFIERread-createcurrent
rmonAlarmSampleType
OBJECT-TYPE
The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.4.1.1.4INTEGER {absoluteValue(1), deltaValue(2)}read-createcurrent
rmonAlarmRisingThreshold
OBJECT-TYPE
A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.4.1.1.5Integer32read-createcurrent
rmonAlarmFallingThreshold
OBJECT-TYPE
A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.4.1.1.6Integer32read-createcurrent
rmonAlarmRisingEventIndex
OBJECT-TYPE
The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.4.1.1.7Integer32 (0..65535)read-createcurrent
rmonAlarmFallingEventIndex
OBJECT-TYPE
The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.7.47.4.1.1.8Integer32 (0..65535)read-createcurrent
rmonAlarmOwner
OBJECT-TYPE
The entity that configured this entry and is therefore using the resources assigned to it.
1.3.6.1.4.1.171.10.75.7.47.4.1.1.9OCTET STRING (SIZE(1..32))read-createcurrent
rmonAlarmStatus
OBJECT-TYPE
The status of this alarm entry.
1.3.6.1.4.1.171.10.75.7.47.4.1.1.10RmonStatusread-createcurrent
rmonEvent
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.47.5
rmonEventTable
OBJECT-TYPE
A list of events to be generated.
1.3.6.1.4.1.171.10.75.7.47.5.1not-accessiblecurrent
rmonEventEntry
OBJECT-TYPE
A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be named eventLastTimeSent.6
1.3.6.1.4.1.171.10.75.7.47.5.1.1not-accessiblecurrent
rmonEventIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur.
1.3.6.1.4.1.171.10.75.7.47.5.1.1.1Integer32 (1..65535)read-onlycurrent
rmonEventDescription
OBJECT-TYPE
A comment describing this event entry.
1.3.6.1.4.1.171.10.75.7.47.5.1.1.2DisplayString (SIZE(0..127))read-createcurrent
rmonEventType
OBJECT-TYPE
The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations.
1.3.6.1.4.1.171.10.75.7.47.5.1.1.3INTEGER {none(1), log(2), snmptrap(3), logandtrap(4)}read-createcurrent
rmonEventCommunity
OBJECT-TYPE
If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string.
1.3.6.1.4.1.171.10.75.7.47.5.1.1.4OCTET STRING (SIZE(1..32))read-createcurrent
rmonEventOwner
OBJECT-TYPE
The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this device
1.3.6.1.4.1.171.10.75.7.47.5.1.1.5OCTET STRING (SIZE(1..32))read-createcurrent
rmonEventStatus
OBJECT-TYPE
The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent.
1.3.6.1.4.1.171.10.75.7.47.5.1.1.6RmonStatusread-createcurrent
companyNeighbor
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.7.50
neighborTable
OBJECT-TYPE
A list of the Neighbor Cache Table.
1.3.6.1.4.1.171.10.75.7.50.1not-accessiblecurrent
neighborEntry
OBJECT-TYPE
A Neighbor cache entry containing the ifindex and ipv6 addr.
1.3.6.1.4.1.171.10.75.7.50.1.1not-accessiblecurrent
neighborIfindex
OBJECT-TYPE
The interface index of the Neighbor entry.
1.3.6.1.4.1.171.10.75.7.50.1.1.1INTEGERread-onlycurrent
neighborIPv6Addr
OBJECT-TYPE
Allows the entry of an IP address that will be a Neighbor entry into the Neighbor Cache Table.
1.3.6.1.4.1.171.10.75.7.50.1.1.2Ipv6Addressread-onlycurrent
neighborMACAddr
OBJECT-TYPE
The MAC address associated of the Neighbor entry.
1.3.6.1.4.1.171.10.75.7.50.1.1.3MacAddressread-onlycurrent
neighborType
OBJECT-TYPE
The type associated of the Neighbor entry.
1.3.6.1.4.1.171.10.75.7.50.1.1.4INTEGER {static(1), dynamic(2)}read-onlycurrent
neighborCacheState
OBJECT-TYPE
The type associated of the Neighbor entry.
1.3.6.1.4.1.171.10.75.7.50.1.1.5INTEGER {static(1), reachable(2), incomplete(3), stale(4), delay(5), probe(6), notinservice(7)}read-onlycurrent
neighborRowStatus
OBJECT-TYPE
The status of an entry in the Neighbor Cache Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.7.50.1.1.7RowStatusread-writecurrent

Notifications

NameOIDStatus
topologyChange
NOTIFICATION-TYPE
AST_TOPOLOGY_CHG_TRAP_VAL.
1.3.6.1.4.1.171.10.75.7.27.0.4current
firmwareUpgradeSuccess
NOTIFICATION-TYPE
SNMP_FIRMUPGRADE_SUCC.
1.3.6.1.4.1.171.10.75.7.27.0.8current
firmwareUpgradeFailure
NOTIFICATION-TYPE
SNMP_FIRMUPGRADE_FAIL.
1.3.6.1.4.1.171.10.75.7.27.0.9current
firmwareIllegalFile
NOTIFICATION-TYPE
SNMP_FIRMUPGRADE_FAIL2.
1.3.6.1.4.1.171.10.75.7.27.0.10current
firmwareTransferError
NOTIFICATION-TYPE
SNMP_FIRMUPGRADE_FAIL1.
1.3.6.1.4.1.171.10.75.7.27.0.11current
firmwareChecksumError
NOTIFICATION-TYPE
SNMP_FIRMUPGRADE_FAIL3.
1.3.6.1.4.1.171.10.75.7.27.0.12current