DES-1210-28ME_B2

TEXTUAL-CONVENTION

The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge). Several objects in this MIB module represent values of timers used by the Spanning Tree Protocol. In this MIB, these timers have values in units of hundreths of a second (i.e. 1/100 secs). These timers, when stored in a Spanning Tree Protocol's BPDU, are in units of 1/256 seconds. Note, however, that 802.1D-1990 specifies a settable granularity of no more than 1 second for these timers. To avoid ambiguity, a data type is defined here as a textual convention and all representation of these timers in this MIB module are defined using this data type. An algorithm is also defined for converting between the different units, to ensure a timer's value is not distorted by multiple conversions.

TEXTUAL-CONVENTION

The Actor or Partner Key value (0..65535).

TEXTUAL-CONVENTION

This TC describes the link aggregation status. The bit 'aggCapable(0)' indicates the link is capable of being aggregated. The bit 'aggEnabled(1)' indicates the link is currently in aggregation.

TEXTUAL-CONVENTION

The value of a management address associated with the LLDP agent that may be used to reach higher layer entities to assist discovery by network management. It should be noted that appropriate security credentials, such as SNMP engineId, may be required to access the LLDP agent using a management address. These necessary credentials should be known by the network management and the objects associated with the credentials are not included in the LLDP agent.

TEXTUAL-CONVENTION

Each port contained in the chassis (that is known to the LLDP agent) is uniquely identified by a port number. A port number has no mandatory relationship to an InterfaceIndex object (of the interfaces MIB, IETF RFC 2863). If the LLDP agent is a IEEE 802.1D, IEEE 802.1Q bridge, the LldpPortNumber will have the same value as the dot1dBasePort object (defined in IETF RFC 1493) associated corresponding bridge port. If the system hosting LLDP agent is not an IEEE 802.1D or an IEEE 802.1Q bridge, the LldpPortNumber will have the same value as the corresponding interface's InterfaceIndex object. Port numbers should be in the range of 1 and 4096 since a particular port is also represented by the corresponding port number bit in LldpPortList.

TEXTUAL-CONVENTION

This TC describes the Power over Ethernet (PoE) port class.

TEXTUAL-CONVENTION

This data type is used to model an administratively assigned name of the owner of a resource. Implementations must accept values composed of well-formed NVT ASCII sequences. In addition, implementations should accept values composed of well-formed UTF-8 sequences. It is suggested that this name contain one or more of the following: IP address, management station name, network manager's name, location, or phone number. In some cases the agent itself will be the owner of an entry. In these cases, this string shall be set to a string starting with 'monitor'. SNMP access control is articulated entirely in terms of the contents of MIB views; access to a particular SNMP object instance depends only upon its presence or absence in a particular MIB view and never upon its value or the value of related object instances. Thus, objects of this type afford resolution of resource contention only among cooperating managers; they realize no access control function with respect to uncooperative parties.

TEXTUAL-CONVENTION

Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. static(2) - force the port to enable channeling. disable(3) - channeling is disabled.

TEXTUAL-CONVENTION

Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.

TEXTUAL-CONVENTION

The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries currently not in use. Proper interpretation of such entries requires examination of the relevant RmonStatus object. An existing instance of this object cannot be set to createRequest(2). This object may only be set to createRequest(2) when this instance is created. When this object is created, the agent may wish to create supplemental object instances with default values to complete a conceptual row in this table. Because the creation of these default objects is entirely at the option of the agent, the manager must not assume that any will be created, but may make use of any that are created. Immediately after completing the create operation, the agent must set this object to underCreation(3). When in the underCreation(3) state, an entry is allowed to exist in a possibly incomplete, possibly inconsistent state, usually to allow it to be modified in multiple PDUs. When in this state, an entry is not fully active. Entries shall exist in the underCreation(3) state until the management station is finished configuring the entry and sets this object to valid(1) or aborts, setting this object to invalid(4). If the agent determines that an entry has been in the underCreation(3) state for an abnormally long time, it may decide that the management station has crashed. If the agent makes this decision, it may set this object to invalid(4) to reclaim the entry. A prudent agent will understand that the management station may need to wait for human input and will allow for that possibility in its determination of this abnormally long period. An entry in the valid(1) state is fully configured and consistent and fully represents the configuration or operation such a row is intended to represent. For example, it could be a statistical function that is configured and active, or a filter that is available in the list of filters processed by the packet capture process. A manager is restricted to changing the state of an entry in the following ways: To: valid createRequest underCreation invalid From: valid OK NO OK OK createRequest N/A N/A N/A N/A underCreation OK NO OK OK invalid NO NO NO OK nonExistent NO OK NO OK In the table above, it is not applicable to move the state from the createRequest state to any other state because the manager will never find the variable in that state. The nonExistent state is not a value of the enumeration, rather it means that the entryStatus variable does not exist at all. An agent may allow an entryStatus variable to change state in additional ways, so long as the semantics of the states are followed. This allowance is made to ease the implementation of the agent and is made despite the fact that managers should never exercise these additional state transitions.

TEXTUAL-CONVENTION

A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n is the value in 1/100 second units b is the value in 1/256 second units To convert the value from 1/256 second units back to 1/100 seconds, the following algorithm should be used: n = ceiling( (b * 100) / 256) where: ceiling = quotient [if remainder is 0], or quotient + 1 [if remainder is non-zero] n is the value in 1/100 second units b is the value in 1/256 second units Note: it is important that the arithmetic operations are done in the order specified (i.e., multiply first, divide second).

TEXTUAL-CONVENTION

A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) ¡V + _ = .

OBJECT-TYPE

Version number of the Hardware.

OBJECT-TYPE

Version number of the Firmware.

OBJECT-TYPE

This time interval is used to count the time and logout web interface automatically.

OBJECT-TYPE

The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.

OBJECT-TYPE

Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Interval.

OBJECT-TYPE

This object is used to set Safeguard Enable\Disable.

OBJECT-TYPE

This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'.

OBJECT-TYPE

This object is used to save Configuration.

OBJECT-TYPE

A table to control the port specific parameters of the device like speed, duplex mode, etc.

OBJECT-TYPE

An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.

OBJECT-TYPE

Interface index of the port for the configuration in this entry applies.

OBJECT-TYPE

This object indicates the port type: fiber 1G/100M or copper.

OBJECT-TYPE

Configures interface speed.

OBJECT-TYPE

The port's operating speed state.

OBJECT-TYPE

Configures interface auto/mdi/mdix mode. The default setting is Auto.

OBJECT-TYPE

Enables / disables flow control for the interface.

OBJECT-TYPE

The link parner negotiate port's operating flow control state.

OBJECT-TYPE

The port's media type.

OBJECT-TYPE

The port description table.

OBJECT-TYPE

The port description entry.

OBJECT-TYPE

This object indicates the port index.

OBJECT-TYPE

This object indicates the port type: fiber 1G/100M or copper.

OBJECT-TYPE

This object indicates the port description.

OBJECT-TYPE

The port error table.

OBJECT-TYPE

A list of information for the err port of the device.

OBJECT-TYPE

This object indicates the module's port number.(1..Max port number in the module)

OBJECT-TYPE

This object decides whether the port state is enabled or disabled.

OBJECT-TYPE

This object decides whether the PortStatus is err-disabled.

OBJECT-TYPE

This object decides whether the PortStatus is LBD.

OBJECT-TYPE

This object indicates auto config is enabled or disabled.

OBJECT-TYPE

This object is for Enabled(1) or Disabled(2) Web state in the system.

OBJECT-TYPE

Web Server Port Number.

OBJECT-TYPE

This object is for ARP aging time.

OBJECT-TYPE

This object is for MAC aging time.

OBJECT-TYPE

Enable/Disable management Telnetsetting mechanism.

OBJECT-TYPE

The value is for setting telnet's UDP Port.

OBJECT-TYPE

To set the WEB panel auto refresh timer.

OBJECT-TYPE

To set enable status for flood fdb.

OBJECT-IDENTITY

OBJECT-TYPE

Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.

OBJECT-TYPE

Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.

OBJECT-TYPE

IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.

OBJECT-TYPE

Gateway

OBJECT-TYPE

Status of DHCP Option12

OBJECT-TYPE

Host name in DHCP option 12

OBJECT-IDENTITY

OBJECT-TYPE

The TFTP server's IP address is used to upload or download firmware.

OBJECT-TYPE

Configure firmware filename to download.

OBJECT-TYPE

The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName.

OBJECT-TYPE

The tftp operation status represent firmware backup or upgrade status.

OBJECT-TYPE

The TFTP server's IP address is used to upload or download configuration file.

OBJECT-TYPE

The configuration filename is used to store or retrieve config from the tftp server.

OBJECT-TYPE

The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName.

OBJECT-TYPE

The tftp operation status represent configuration file backup or restore status.

OBJECT-IDENTITY

OBJECT-TYPE

Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing.

OBJECT-TYPE

Resets the units statistics. A (1) resets the statistics count, a (2) does nothing.

OBJECT-IDENTITY

OBJECT-TYPE

This object is for enabling or disabling SNMP Community function.

OBJECT-IDENTITY

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.

OBJECT-TYPE

A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.

OBJECT-TYPE

The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.

OBJECT-TYPE

An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol.

OBJECT-TYPE

OBJECT-TYPE

An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned.

OBJECT-TYPE

OBJECT-TYPE

The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.

OBJECT-IDENTITY

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.

OBJECT-TYPE

In order to gain the access rights allowed by this conceptual row, this securityModel must be in use.

OBJECT-TYPE

The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected.

OBJECT-TYPE

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

OBJECT-TYPE

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

OBJECT-TYPE

The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.

OBJECT-TYPE

The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.

OBJECT-IDENTITY

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

The human readable name for a family of view subtrees.

OBJECT-TYPE

The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees.

OBJECT-TYPE

The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only.

OBJECT-TYPE

Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view.

OBJECT-TYPE

The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.

OBJECT-IDENTITY

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

The unique index value of a row in this table.

OBJECT-TYPE

A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format.

OBJECT-TYPE

The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1).

OBJECT-IDENTITY

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.

OBJECT-TYPE

The locally arbitrary.

OBJECT-TYPE

The Level of Security to be used when generating SNMP messages using this entry.

OBJECT-TYPE

OBJECT-TYPE

An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate.

OBJECT-IDENTITY

OBJECT-TYPE

This object is for enabling or disabling SNMP login fail event trap in the system.

OBJECT-TYPE

This object is for enabling or disabling devie Bootup event trap in the system.

OBJECT-TYPE

This object is for enabling or disabling Fiber link up / link down event trap in the system.

OBJECT-TYPE

This object is for enabling or disabling Copper link up / link down event trap in the system.

OBJECT-TYPE

This object is for enabling or disabling RSTP topology change event trap in the system.

OBJECT-TYPE

This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system.

OBJECT-TYPE

Used to configure trap settings for BPDU attack protection events.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

This object is for enabling or disabling send gratuitous trap when IP address conflicted in the network.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.

OBJECT-TYPE

The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w and 'mstp(3)' indicates the Multiple Spanning Tree Protocol Specified in IEEE 802.1s.

OBJECT-TYPE

The Value of the writable portion of the Bridge Identifier comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

OBJECT-TYPE

The value used by the Port Transmit state machine to limit the maximum transmission rate.

OBJECT-TYPE

The value that all bridges use for MaxAge when this bridge is acting as the root. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

OBJECT-TYPE

The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.

OBJECT-TYPE

The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D specifies that the range for this parameter is related to the value of BridgeMaxAge. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.

OBJECT-TYPE

This object is for enabling or disabling forward BPDU.

OBJECT-TYPE

The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node.

OBJECT-TYPE

The Cost of the path to the CIST Root as seen from this bridge.

OBJECT-TYPE

The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.

OBJECT-TYPE

This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state.

OBJECT-TYPE

The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge.

OBJECT-TYPE

A table that contains port-specific information for the Spanning Tree Protocol.

OBJECT-TYPE

A list of information maintained by every port about the Spanning Tree Protocol state for that port.

OBJECT-TYPE

The Port number of the port for which this entry contains spanning tree information.

OBJECT-TYPE

Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts

OBJECT-TYPE

The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are set for Port Priority must be in steps of 16.

OBJECT-TYPE

The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read.

OBJECT-TYPE

The contribution of this port to the path cost of paths towards the CIST Root which include this port.

OBJECT-TYPE

Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transmit MSTP BPDUs without instance information. Any other operation on this object has no effect and it always returns FALSE(2) when read.

OBJECT-TYPE

This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.

OBJECT-TYPE

The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.

OBJECT-TYPE

A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.

OBJECT-TYPE

A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC_Operational for the attached LANs transitions frequently.

OBJECT-TYPE

The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.

OBJECT-TYPE

Current state of the Port as defined by the Common spanning tree protocol.

OBJECT-TYPE

This object is for enabling or disabling forward BPDU.

OBJECT-IDENTITY

OBJECT-TYPE

The Name for the Region's configuration. By Default Region Name will be equal to the Bridge Mac Address.

OBJECT-TYPE

Version of the MST Region.

OBJECT-TYPE

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

OBJECT-TYPE

This table contains one entry for each instance of MSTP. This table maintains context ID as one more index to support Multiple Instances.

OBJECT-TYPE

A conceptual row containing the status of the MSTP instance.

OBJECT-TYPE

An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance.

OBJECT-TYPE

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values.

OBJECT-TYPE

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to unmap from this Instance. A vlan may not be unmapped from this instance if it is not already mapped to this Instance. This object is used only for SET operation.GET Operation returns null values.

OBJECT-TYPE

A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

OBJECT-TYPE

A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.

OBJECT-IDENTITY

OBJECT-TYPE

The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

OBJECT-TYPE

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.

OBJECT-TYPE

Table containing Bridge Information specific to Spanning Tree Instance. This table maintains context ID as one more index to support Multiple Instances.

OBJECT-TYPE

Entry indicating the Bridge Information.

OBJECT-TYPE

Spanning Tree Instance to which the information belongs.

OBJECT-TYPE

The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.

OBJECT-TYPE

The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains Common Spanning Tree Port Information.

OBJECT-TYPE

A list of information maintained by every port for Common Spanning tree.

OBJECT-TYPE

The Port number of the port for which this entry contains spanning tree information.

OBJECT-TYPE

The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.

OBJECT-TYPE

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

OBJECT-TYPE

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

OBJECT-TYPE

The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.

OBJECT-TYPE

Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port

OBJECT-TYPE

Current Port Role of the port for this spanning tree instance.

OBJECT-TYPE

This table contains Spanning Tree Instance Specific Port Information.

OBJECT-TYPE

A list of information maintained by every port for each and every spanning tree instance.

OBJECT-TYPE

The Port number of the port for which this entry contains spanning tree information.

OBJECT-TYPE

The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.

OBJECT-TYPE

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

OBJECT-TYPE

The contribution of this port to the path cost of paths towards the MSTI Root which include this port.

OBJECT-TYPE

The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.

OBJECT-TYPE

Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port

OBJECT-TYPE

Current Port Role of the port for this spanning tree instance.

OBJECT-IDENTITY

OBJECT-TYPE

Enable/Disable management VLAN mechanism.

OBJECT-TYPE

The management VLAN ID, which will allow to forward packets of that VLAN to CPU.

OBJECT-TYPE

Enable/Disable IEEE 802.1Q Asymmetric VLAN

OBJECT-TYPE

A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

OBJECT-TYPE

Information for a VLAN configured into the device by (local or network) management.

OBJECT-TYPE

An administratively assigned string, which may be used to identify the VLAN.

OBJECT-TYPE

The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.

OBJECT-TYPE

The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set.

OBJECT-TYPE

The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.

OBJECT-TYPE

Enable/Disable Advertisement Status of the IEEE 802.1Q VLAN.

OBJECT-TYPE

The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Sets the Link Aggregation Module administrative status as enabled or disabled.

OBJECT-TYPE

A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel.

OBJECT-TYPE

There is one entry in this table for each created port-channel port.

OBJECT-TYPE

The index of the port-channel(Aggregator's interface index).

OBJECT-TYPE

Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.

OBJECT-TYPE

Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.

OBJECT-TYPE

The master port of the port-channel.

OBJECT-TYPE

Sets the Link Aggregation load balance algorithm.

OBJECT-IDENTITY

OBJECT-TYPE

A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port.

OBJECT-TYPE

A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device.

OBJECT-TYPE

The index of the port.

OBJECT-TYPE

The priority value assigned to this Aggregation Port. This 16-bit value is read-write.

OBJECT-TYPE

This object indicates LACP_Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets.

OBJECT-TYPE

This object indicates LACP_Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds.

OBJECT-IDENTITY

OBJECT-TYPE

Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning.

OBJECT-TYPE

The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable.

OBJECT-TYPE

A list of the Static MACs

OBJECT-TYPE

A Static MAC entry containing the mac and forwarding port.

OBJECT-TYPE

The VLAN ID of the static MAC entry.

OBJECT-TYPE

The MAC address associated of the static MAC entry.

OBJECT-TYPE

The forwarding port of the static MAC entry.

OBJECT-TYPE

The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations.

OBJECT-TYPE

This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.

OBJECT-TYPE

This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.

OBJECT-TYPE

When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.

OBJECT-TYPE

The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.

OBJECT-TYPE

This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for VLANs.

OBJECT-TYPE

The maximum query response time advertised in IGMPv2 general queries on this interface.

OBJECT-TYPE

The maximum data driven learning entry value.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains the list of ports through which a router, in a particular VLAN is reachable.

OBJECT-TYPE

Contains the VLAN ID and list of ports on which routers are present in the VLAN.

OBJECT-TYPE

VLAN ID of the ports through which router is reachable.

OBJECT-TYPE

List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.

OBJECT-TYPE

This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.

OBJECT-TYPE

Contains snooping status , version and fast leave configuration for a specific VLAN.

OBJECT-TYPE

Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.

OBJECT-TYPE

This object allows you to enable/disable IGS function on a specific VLAN.

OBJECT-TYPE

Indicates whether the switch is configured as a querier in the VLAN

OBJECT-TYPE

The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.

OBJECT-TYPE

This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.

OBJECT-TYPE

List of ports which are configured statically as router ports

OBJECT-TYPE

List of ports which can be configured statically as forbidden router ports.

OBJECT-TYPE

Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table.

OBJECT-TYPE

This object allows you to enable/disable Data Driven Learning function on a specific VLAN.

OBJECT-TYPE

This table contains MAC based multicast forwarding information.

OBJECT-TYPE

This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.

OBJECT-TYPE

VLAN ID pertaining to the Multicast forwarding entry

OBJECT-TYPE

Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.

OBJECT-TYPE

Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.

OBJECT-TYPE

List of ports onto which the multicast data packets destined for this group will be forwarded.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to manage the IGMP Authentication function of the switch.

OBJECT-TYPE

Contains management entities for IGMP Authentication function.

OBJECT-TYPE

The port index of igsAccessAuthTable which indicates the port to be configured.

OBJECT-TYPE

This object can be configured to set IGMP Authentication state to enabled/disabled on each port.

OBJECT-IDENTITY

OBJECT-TYPE

This table is used to manage the IGMP Host based Fast Leave function of the switch.

OBJECT-TYPE

Contains management entities for IGMP Host based fast leave function.

OBJECT-TYPE

VLAN ID of Host table entry.

OBJECT-TYPE

Group address of Host table entry.

OBJECT-TYPE

Port number of Host table entry.

OBJECT-TYPE

Host IP address of Group in Host table entry.

OBJECT-IDENTITY

OBJECT-TYPE

Enable/Disable GVRP mechanism.

OBJECT-TYPE

The Join Time value assigned to this Join Time field. This 16-bit value is read-write.

OBJECT-TYPE

The Leave Time value assigned to this Leave Time field. This 16-bit value is read-write.

OBJECT-TYPE

The Leave_All Time value assigned to this Leave_All Time field. This 16-bit value is read-write.

OBJECT-TYPE

A table containing static configuration information for each GVRP configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.

OBJECT-TYPE

Information for a GVRP configured into the device by (local or network) management.

OBJECT-TYPE

The index of the port.

OBJECT-TYPE

The PVID value assigned to this Aggregation Port. This 16-bit value is read-write.

OBJECT-TYPE

Enable/Disable GVRP State to this Aggregation Port.

OBJECT-TYPE

Enable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port.

OBJECT-TYPE

Chose types All Frames/Tagged to this Aggregation Port.

OBJECT-IDENTITY

OBJECT-TYPE

Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS3 spec. Queues with higher weights get bandwidth before than other queues with less weights.

OBJECT-IDENTITY

OBJECT-TYPE

A list of cosOutputSchedule.

OBJECT-TYPE

A list of cosOutputClass Weight.

OBJECT-TYPE

A index of class 0 ~ 3.

OBJECT-TYPE

cos weight

OBJECT-IDENTITY

OBJECT-TYPE

A list of 802.1p port default priority Entries.

OBJECT-TYPE

A list of 802.1p port default priority priorities.

OBJECT-TYPE

A port identifier that is in the range of 1 to ifNumber.

OBJECT-TYPE

For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled.

OBJECT-TYPE

For ingress untagged packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled.

OBJECT-IDENTITY

OBJECT-TYPE

A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..3).

OBJECT-TYPE

User Priority to Traffic Class mapping.

OBJECT-TYPE

For ingress tagged packets, D-Link Smart Switches will refer to these information and prioritize them with 4 different priority queues. If 802.1p is enabled.

OBJECT-TYPE

The User Class the received frame is mapped to.

OBJECT-IDENTITY

OBJECT-TYPE

Settings of Qos mode: DSCP QoS or TOS Qos. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) and Highest(6,7), inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic. DSCP : Differentiated services enhancements to the Internet protocol are intended to enable scalable service discrimination in the Internet without the need for per-flow state and signaling at every hop.

OBJECT-IDENTITY

OBJECT-TYPE

DiffServ Type 0 : IP ToS value = 0

OBJECT-TYPE

DiffServ Type 01 : IP ToS value = 4

OBJECT-TYPE

DiffServ Type 02 : IP ToS value = 8

OBJECT-TYPE

DiffServ Type 03 : IP ToS value = 12

OBJECT-TYPE

DiffServ Type 04 : IP ToS value = 16

OBJECT-TYPE

DiffServ Type 05 : IP ToS value = 20

OBJECT-TYPE

DiffServ Type 06 : IP ToS value = 24

OBJECT-TYPE

DiffServ Type 07 : IP ToS value = 28

OBJECT-TYPE

DiffServ Type 08 : IP ToS value = 32

OBJECT-TYPE

DiffServ Type 09 : IP ToS value = 36

OBJECT-TYPE

DiffServ Type 10 : IP ToS value = 40

OBJECT-TYPE

DiffServ Type 11 : IP ToS value = 44

OBJECT-TYPE

DiffServ Type 12 : IP ToS value = 48

OBJECT-TYPE

DiffServ Type 13 : IP ToS value = 52

OBJECT-TYPE

DiffServ Type 14 : IP ToS value = 56

OBJECT-TYPE

DiffServ Type 15 : IP ToS value = 60

OBJECT-TYPE

DiffServ Type 16 : IP ToS value = 64

OBJECT-TYPE

DiffServ Type 17 : IP ToS value = 68

OBJECT-TYPE

DiffServ Type 18 : IP ToS value = 72

OBJECT-TYPE

DiffServ Type 19 : IP ToS value = 76

OBJECT-TYPE

DiffServ Type 20 : IP ToS value = 80

OBJECT-TYPE

DiffServ Type 21 : IP ToS value = 84

OBJECT-TYPE

DiffServ Type 22 : IP ToS value = 88

OBJECT-TYPE

DiffServ Type 23 : IP ToS value = 92

OBJECT-TYPE

DiffServ Type 24 : IP ToS value = 96

OBJECT-TYPE

DiffServ Type 25 : IP ToS value = 100

OBJECT-TYPE

DiffServ Type 26 : IP ToS value = 104

OBJECT-TYPE

DiffServ Type 27 : IP ToS value = 108

OBJECT-TYPE

DiffServ Type 28 : IP ToS value = 112

OBJECT-TYPE

DiffServ Type 29 : IP ToS value = 116

OBJECT-TYPE

DiffServ Type 30 : IP ToS value = 120

OBJECT-TYPE

DiffServ Type 31 : IP ToS value = 124

OBJECT-TYPE

DiffServ Type 32 : IP ToS value = 128

OBJECT-TYPE

DiffServ Type 33 : IP ToS value = 132

OBJECT-TYPE

DiffServ Type 34 : IP ToS value = 136

OBJECT-TYPE

DiffServ Type 35 : IP ToS value = 140

OBJECT-TYPE

DiffServ Type 36 : IP ToS value = 144

OBJECT-TYPE

DiffServ Type 37 : IP ToS value = 148

OBJECT-TYPE

DiffServ Type 38 : IP ToS value = 152

OBJECT-TYPE

DiffServ Type 39 : IP ToS value = 156

OBJECT-TYPE

DiffServ Type 40 : IP ToS value = 160

OBJECT-TYPE

DiffServ Type 41 : IP ToS value = 164

OBJECT-TYPE

DiffServ Type 42 : IP ToS value = 168

OBJECT-TYPE

DiffServ Type 43 : IP ToS value = 172

OBJECT-TYPE

DiffServ Type 44 : IP ToS value = 176

OBJECT-TYPE

DiffServ Type 45 : IP ToS value = 180

OBJECT-TYPE

DiffServ Type 46 : IP ToS value = 184

OBJECT-TYPE

DiffServ Type 47 : IP ToS value = 188

OBJECT-TYPE

DiffServ Type 48 : IP ToS value = 192

OBJECT-TYPE

DiffServ Type 49 : IP ToS value = 196

OBJECT-TYPE

DiffServ Type 50 : IP ToS value = 200

OBJECT-TYPE

DiffServ Type 51 : IP ToS value = 204

OBJECT-TYPE

DiffServ Type 52 : IP ToS value = 208

OBJECT-TYPE

DiffServ Type 53 : IP ToS value = 212

OBJECT-TYPE

DiffServ Type 54 : IP ToS value = 216

OBJECT-TYPE

DiffServ Type 55 : IP ToS value = 220

OBJECT-TYPE

DiffServ Type 56 : IP ToS value = 224

OBJECT-TYPE

DiffServ Type 57 : IP ToS value = 228

OBJECT-TYPE

DiffServ Type 58 : IP ToS value = 232

OBJECT-TYPE

DiffServ Type 59 : IP ToS value = 236

OBJECT-TYPE

DiffServ Type 60 : IP ToS value = 240

OBJECT-TYPE

DiffServ Type 61 : IP ToS value = 244

OBJECT-TYPE

DiffServ Type 62 : IP ToS value = 248

OBJECT-TYPE

DiffServ Type 63 : IP ToS value = 252

OBJECT-IDENTITY

OBJECT-TYPE

TOS 0

OBJECT-TYPE

TOS 01

OBJECT-TYPE

TOS 02

OBJECT-TYPE

TOS 03

OBJECT-TYPE

TOS 04

OBJECT-TYPE

TOS 05

OBJECT-TYPE

TOS 06

OBJECT-TYPE

TOS 07

OBJECT-IDENTITY

OBJECT-TYPE

A list of port priority settings.

OBJECT-TYPE

A list of port priority settings Entries.

OBJECT-TYPE

A port identifier that is in the range of 1 to ifNumber.

OBJECT-TYPE

The port priority setting type. (ex. none = 0, 802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value is 2 + 4 = 6.

OBJECT-IDENTITY

OBJECT-TYPE

A list of priority by acl setting.

OBJECT-TYPE

A list of priority by acl setting entry.

OBJECT-TYPE

Index of priority by acl setting.

OBJECT-TYPE

Type of priority by acl setting.

OBJECT-TYPE

Dst MAC of priority by acl setting.

OBJECT-TYPE

Dst IP of priority by acl setting

OBJECT-TYPE

Dst TCP/UDP port of priority by acl setting

OBJECT-TYPE

VLAN ID of priority by acl setting

OBJECT-TYPE

Ip protocol number of priority by acl setting

OBJECT-TYPE

Be mapped class of priority by acl setting.

OBJECT-TYPE

Status of priority by acl setting.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.

OBJECT-TYPE

An entry appears in this table for each physical interface in the switch.

OBJECT-TYPE

The interface index for which the configuration in this entry applies.

OBJECT-TYPE

Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port.

OBJECT-TYPE

Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port.

OBJECT-IDENTITY

OBJECT-TYPE

The trap setting of traffic control.

OBJECT-TYPE

The traffic control table.

OBJECT-TYPE

The traffic control entry.

OBJECT-TYPE

The traffic control index.

OBJECT-TYPE

The action mode of traffic control.

OBJECT-TYPE

The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast)

OBJECT-TYPE

The threshold of traffic control.

OBJECT-TYPE

The count down value of traffic control.

OBJECT-TYPE

The time interval of traffic control.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.

OBJECT-TYPE

A table to configure trusted host in the system.

OBJECT-TYPE

Each entry in this table represents rules for particular trusted host.

OBJECT-TYPE

The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.

OBJECT-TYPE

Used to mask with IP address, it allow you set a subnet as a trusted host entry.

OBJECT-TYPE

The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.

OBJECT-IDENTITY

OBJECT-TYPE

A table to control port security features of the device.

OBJECT-TYPE

An entry appears in port security table for each interface in the system.

OBJECT-TYPE

The interface index for which the configuration in this entry applies.

OBJECT-TYPE

Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled.

OBJECT-TYPE

Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address.

OBJECT-TYPE

Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTimeout : The locked addresses will age out after the aging timer expires. Permanent : The locked addresses will not age out after the aging timer expires.

OBJECT-TYPE

A table to control port security FDB Permanent of the device.

OBJECT-TYPE

An entry appears in port security table for each interface in the system.

OBJECT-TYPE

The index of the port security MAC entry.

OBJECT-TYPE

The VLAN ID of the port security MAC entry.

OBJECT-TYPE

The MAC address associated of the port security MAC entry.

OBJECT-TYPE

The forwarding port of the port security MAC entry.

OBJECT-IDENTITY

OBJECT-TYPE

A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch.

OBJECT-TYPE

An entry appears in this table for each interface in the system.

OBJECT-TYPE

Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.

OBJECT-TYPE

Ethernet Mac Address.

OBJECT-TYPE

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

OBJECT-TYPE

This object indicates the status of this entry.

OBJECT-IDENTITY

OBJECT-TYPE

This object is for enabling or disabling secure HTTP in the system.

OBJECT-IDENTITY

OBJECT-TYPE

This object is to configure the cipher-suites list.

OBJECT-IDENTITY

OBJECT-TYPE

To enable or disable DHCP Server Screening port list.

OBJECT-TYPE

A table to control filter DHCP Server for the entire switch or for each interface in the switch.

OBJECT-TYPE

An entry appears in this table for each interface in the system.

OBJECT-TYPE

Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.

OBJECT-TYPE

Ethernet Mac Address.

OBJECT-TYPE

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

OBJECT-TYPE

This object indicates the status of this entry.

OBJECT-IDENTITY

OBJECT-TYPE

This object is for enabling or disabling ssh in the system.

OBJECT-TYPE

This object indicates the max auth fail retry attempt times.

OBJECT-TYPE

This object indicates one SSH session rekey time interval.

OBJECT-TYPE

This object indicates max SSH session number supported in system.

OBJECT-TYPE

This object indicates SSH connection timeout value.

OBJECT-TYPE

The object indicates authen method password is enabled or disabled.

OBJECT-TYPE

The object indicates authen method public-key is enabled or disabled.

OBJECT-TYPE

The object indicates authen method host-key is enabled or disabled.

OBJECT-TYPE

This object is to configure the cipher-suites list.

OBJECT-TYPE

This object is to configure the MAC-list.

OBJECT-TYPE

The object indicates Public key generating algorithm RSA is enabled or disabled.

OBJECT-TYPE

A table to configure SSH user auth in the system.

OBJECT-TYPE

An entry to configure user auth in the system.

OBJECT-TYPE

The Schedule identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 8.

OBJECT-TYPE

The ssh user name associated with the SSH suer Info. entry (e.g., `admin, user').

OBJECT-TYPE

The object indicates which auth used by the user.

OBJECT-TYPE

The ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2').

OBJECT-TYPE

SSH HostBased IP Address of the system.

OBJECT-IDENTITY

OBJECT-TYPE

A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel

OBJECT-TYPE

There is one entry in this table for each created port-channel port

OBJECT-TYPE

The ifIndex of the port-channel(Aggregator's interface index).

OBJECT-TYPE

Port list of port channel.

OBJECT-IDENTITY

OBJECT-TYPE

A table to control IP-MAC-Port Binding Setting features of the device.

OBJECT-TYPE

An entry appears in IP-MAC-Port Binding Setting table for each interface in the system.

OBJECT-TYPE

Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.

OBJECT-TYPE

Disable / enable IP-MAC-Port Binding admin state for the interface.

OBJECT-TYPE

Enable / disable IP-MAC-Port Binding also inspect IP packets state for the interface.

OBJECT-TYPE

Disable / enable IP-MAC-Port Binding DHCP snooping state for the interface.

OBJECT-TYPE

A table to control Smart IP-MAC-Port Binding features of the device.

OBJECT-TYPE

An entry appears in Smart IP-MAC-Port Binding table for each interface in the system.

OBJECT-TYPE

The MAC address associated of the smart IP-MAC-PORT Binding entry.

OBJECT-TYPE

The port number of the smart IP-MAC-PORT Binding entry.

OBJECT-TYPE

The IP address associated of the smart IP-MAC-PORT Binding entry.

OBJECT-TYPE

The VLAN ID of the smart IP-MAC-PORT Binding entry.

OBJECT-TYPE

Disable / enable IP-MAC-Port Binding for the interface.

OBJECT-TYPE

A table to control Manual IP-MAC-Port Binding white list features of the device.

OBJECT-TYPE

An entry appears in Manual IP-MAC-Port Binding white list table for each interface in the system.

OBJECT-TYPE

The IP address associated of the Manual IP-MAC-PORT Binding white list entry.

OBJECT-TYPE

The MAC address associated of the Manual IP-MAC-PORT Binding white list entry.

OBJECT-TYPE

The port number of the Manual IP-MAC-PORT Binding white list entry.

OBJECT-TYPE

The status of a row in impbWhiteListTable. By setting this object, new entries can be created in impbWhiteListTable and existing entries can be removed from impbWhiteListTable. It can be used as specified in the SNMP v2 standard.

OBJECT-TYPE

A table to control IP-MAC-Port Binding black list of the device.

OBJECT-TYPE

An entry appears in Manual IP-MAC-Port Binding black list table for each interface in the system.

OBJECT-TYPE

The MAC address associated of the IP-MAC-PORT Binding black list entry.

OBJECT-TYPE

The VLAN ID of the IP-MAC-PORT Binding black list entry.

OBJECT-TYPE

The port number of the IP-MAC-PORT Binding black list entry.

OBJECT-TYPE

The IP address associated of the IP-MAC-PORT Binding black list entry.

OBJECT-TYPE

nothing/delete IP-MAC-Port Binding for the interface.

OBJECT-TYPE

The begin for IP address associated of the IP-MAC-PORT Binding auto scan entry.

OBJECT-TYPE

The end for IP address associated of the IP-MAC-PORT Binding auto scan entry.

OBJECT-TYPE

Nothing / scan IP-MAC-Port Binding auto scan for the interface.

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates the Access Authentication is enable or disable.

OBJECT-TYPE

Timeout in second for login authentication response.

OBJECT-TYPE

The amount for login authentication, if login failure exceed, connection or access would be locked.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console

OBJECT-TYPE

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.

OBJECT-TYPE

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH.

OBJECT-TYPE

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.

OBJECT-IDENTITY

OBJECT-TYPE

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console.

OBJECT-TYPE

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.

OBJECT-TYPE

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH.

OBJECT-TYPE

Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.

OBJECT-TYPE

A table that contains informations about server group.

OBJECT-TYPE

A list of the group including servers.

OBJECT-TYPE

A value that uniquely identifies this SwAACServerGroupEntry .

OBJECT-TYPE

A human-readable text string of the method group. The name is writable only if Group is new created, which the value of aacServerGroupRowStatus is 'notReady'.

OBJECT-TYPE

The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it.

OBJECT-TYPE

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

OBJECT-TYPE

A table that contains information about severs.

OBJECT-TYPE

A list of the information of server .

OBJECT-TYPE

A value that uniquely identifies this SwAACServerGroupEntry.

OBJECT-TYPE

The IP address of Server

OBJECT-TYPE

The authentication protocol provided by the Server.

OBJECT-TYPE

The TCP/IP port .

OBJECT-TYPE

The key used while authentication process.

OBJECT-TYPE

Server response timeout .

OBJECT-TYPE

Client retry count . (-1: No retry mechanism)

OBJECT-TYPE

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

OBJECT-TYPE

A table that contains information about Login authentication method lists.

OBJECT-TYPE

A list of the Authentication methods.

OBJECT-TYPE

A value that identifies this method list.

OBJECT-TYPE

A human-readable text string of the method list.

OBJECT-TYPE

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

OBJECT-TYPE

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

OBJECT-TYPE

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

OBJECT-TYPE

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

OBJECT-TYPE

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

OBJECT-TYPE

A table that contains information about Enable authentication method lists.

OBJECT-TYPE

A list of the Authentication methods.

OBJECT-TYPE

A value that identifies this method list.

OBJECT-TYPE

A human-readable text string of the method list.

OBJECT-TYPE

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

OBJECT-TYPE

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

OBJECT-TYPE

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

OBJECT-TYPE

The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.

OBJECT-TYPE

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

OBJECT-TYPE

This object is used to set Local Enable Password.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table to ACL profile .

OBJECT-TYPE

Each entry in this table is a ACL profile. Index to the table is ACL profile ID.

OBJECT-TYPE

The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.

OBJECT-TYPE

The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, arpSP_permit(4) - for ARP Spoofing prevention entry, arpSP_deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. userDefined(9) - for User Defined entry. Note that only l2, l3 and userDefined could be set by user, other is reserved for system to show information.

OBJECT-TYPE

The number of rules in this profile.

OBJECT-TYPE

Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 ARP-SP ARP_SENDER_MAC 14 ARP-SP ARP_SENDER_IP 15 L3 TOS 16 (MSB) ------------------------------------------- The value is in Hex format.

OBJECT-TYPE

The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.

OBJECT-TYPE

The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.

OBJECT-TYPE

Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.

OBJECT-TYPE

The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.

OBJECT-TYPE

The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

OBJECT-TYPE

The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

OBJECT-TYPE

The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.

OBJECT-TYPE

The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.

OBJECT-TYPE

The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.

OBJECT-TYPE

The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.

OBJECT-TYPE

Indicate which Udf field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ UDF Offset1 0 (LSB) UDF Offset2 1 UDF Offset3 2 UDF Offset4 3 ------------------------------------------- The value is in Hex format.

OBJECT-TYPE

The value of offset Base.

OBJECT-TYPE

The value of offset Byte from base.

OBJECT-TYPE

The value of offset MAsk.

OBJECT-TYPE

The value of offset Base.

OBJECT-TYPE

The value of offset Byte from base.

OBJECT-TYPE

The value of offset MAsk.

OBJECT-TYPE

The value of offset Base.

OBJECT-TYPE

The value of offset Byte from base.

OBJECT-TYPE

The value of offset MAsk.

OBJECT-TYPE

The value of offset Base.

OBJECT-TYPE

The value of offset Byte from base.

OBJECT-TYPE

The value of offset MAsk.

OBJECT-TYPE

This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.

OBJECT-IDENTITY

OBJECT-TYPE

A table to configure L2 filter rules in the system.

OBJECT-TYPE

Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.

OBJECT-TYPE

L2 Filter rule ID.

OBJECT-TYPE

ACL Profile ID which this rule join.

OBJECT-TYPE

The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.

OBJECT-TYPE

Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.

OBJECT-TYPE

Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address

OBJECT-TYPE

Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.

OBJECT-TYPE

802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.

OBJECT-TYPE

The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.

OBJECT-TYPE

The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.

OBJECT-TYPE

Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.

OBJECT-TYPE

Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.

OBJECT-TYPE

Rate limit for matched packet.

OBJECT-TYPE

Replace DSCP for matched packet.

OBJECT-TYPE

Replace DSCP for matched packet.

OBJECT-TYPE

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

OBJECT-IDENTITY

OBJECT-TYPE

A table to configure L3 filter rules in the system.

OBJECT-TYPE

Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.

OBJECT-TYPE

L3 Filter rule ID.

OBJECT-TYPE

The Profile ID which this rule join.

OBJECT-TYPE

The type of protocol to be checked against the packet.

OBJECT-TYPE

The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.

OBJECT-TYPE

The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),

OBJECT-TYPE

The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),

OBJECT-TYPE

Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.

OBJECT-TYPE

Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.

OBJECT-TYPE

The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.

OBJECT-TYPE

The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.

OBJECT-TYPE

The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.

OBJECT-TYPE

The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.

OBJECT-TYPE

The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.

OBJECT-TYPE

The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.

OBJECT-TYPE

The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.

OBJECT-TYPE

The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.

OBJECT-TYPE

The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.

OBJECT-TYPE

The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition.

OBJECT-TYPE

The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.

OBJECT-TYPE

The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.

OBJECT-TYPE

The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.

OBJECT-TYPE

The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.

OBJECT-TYPE

The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.

OBJECT-TYPE

Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.

OBJECT-TYPE

Specifies the action to be taken on the packet if the filter rule matches.

OBJECT-TYPE

Rate limit for matched packet.

OBJECT-TYPE

ReplaceDSCP for matched packet.

OBJECT-TYPE

ReplaceDSCP for matched packet.

OBJECT-TYPE

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

OBJECT-IDENTITY

OBJECT-TYPE

A table to configure Packet Content filter rules in the system.

OBJECT-TYPE

Each entry in this table is a Packet filter rule. Index to the table is the Packet filter number and Profile ID.

OBJECT-TYPE

Packet Filter rule ID.

OBJECT-TYPE

ACL Profile ID which this rule join.

OBJECT-TYPE

The filter value of Offset 1.

OBJECT-TYPE

The filter value of Offset 2.

OBJECT-TYPE

The filter value of Offset 3.

OBJECT-TYPE

The filter value of Offset 4.

OBJECT-TYPE

Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.

OBJECT-TYPE

Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.

OBJECT-TYPE

Rate limit for matched packet.

OBJECT-TYPE

Replace DSCP for matched packet.

OBJECT-TYPE

Replace 1p for matched packet.

OBJECT-TYPE

This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object is for enabling or disabling syslog alert features in the system and the syslog will save to flash or send to remote syslog server. System Logs record and manage events, as well as report errors and informational messages.

OBJECT-TYPE

This object is for choosing the method to save syslog into flash.

OBJECT-TYPE

When savemode is time interval, it's used to set the interval minutes of system save syslog to flash.

OBJECT-IDENTITY

OBJECT-TYPE

The table of syslog remote server.

OBJECT-TYPE

The list of syslog remote server entry.

OBJECT-TYPE

The index of syslog remote server.

OBJECT-TYPE

The IP Address of syslog remote server.

OBJECT-TYPE

Specifies the log level option to be set for a specific server.

OBJECT-TYPE

The Syslog standard facilities. The facility to be used when sending Syslog messages to this server.

OBJECT-TYPE

The value is for setting UDP Port.

OBJECT-TYPE

The status for this server. If enable, system will send message to this server.

OBJECT-TYPE

Row status of this server entry.

OBJECT-IDENTITY

OBJECT-TYPE

Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator.

OBJECT-TYPE

Loopback detection function mode.

OBJECT-TYPE

Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically.

OBJECT-TYPE

This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds.

OBJECT-TYPE

A table to control Loopback detection features either for the entire switch or for each interface in the switch.

OBJECT-TYPE

An entry appears in this table for each interface in the system.

OBJECT-TYPE

The interface index of the port for which the configuration in this entry applies.

OBJECT-TYPE

Provides control to per port enable or disable the loopback detection function. Default is disabled.

OBJECT-TYPE

The loop status for this port.

OBJECT-TYPE

A table to display Loopback detection features by vlan mode .

OBJECT-TYPE

An entry appears in this table for each interface in the system.

OBJECT-TYPE

Display port lists loop status by vlan.

OBJECT-TYPE

Display port lists loop status by vlan.

OBJECT-IDENTITY

OBJECT-TYPE

Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied.

OBJECT-TYPE

Specifies the port to which the mirrored traffic in the system is to be copied.

OBJECT-TYPE

Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.

OBJECT-TYPE

Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.

OBJECT-IDENTITY

OBJECT-TYPE

A list of the Static MACs

OBJECT-TYPE

A Static MAC entry containing the mac and forwarding port.

OBJECT-TYPE

The VLAN ID of the static MAC entry.

OBJECT-TYPE

The MAC address associated of the static MAC entry.

OBJECT-TYPE

The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.

OBJECT-TYPE

The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.

OBJECT-IDENTITY

OBJECT-TYPE

This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037).

OBJECT-TYPE

SNTP First Server's IP Address

OBJECT-TYPE

SNTP Second Server's IP Address

OBJECT-TYPE

SNTP Poll Interval In Seconds (30-99999)

OBJECT-TYPE

Enable/Disable SNTP function in the system.

OBJECT-TYPE

This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes.

OBJECT-TYPE

Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)

OBJECT-TYPE

The start month of Daylight Saving Time.

OBJECT-TYPE

The start day of Daylight Saving Time.

OBJECT-TYPE

The start hour of Daylight Saving Time.

OBJECT-TYPE

The start minute of Daylight Saving Time.

OBJECT-TYPE

The end month of Daylight Saving Time.

OBJECT-TYPE

The end day of Daylight Saving Time.

OBJECT-TYPE

The end hour of Daylight Saving Time.

OBJECT-TYPE

The end minute of Daylight Saving Time.

OBJECT-TYPE

This object is for Annual(1) or Disabled(2) DST state in the system.

OBJECT-IDENTITY

OBJECT-TYPE

This object is for enabling or disabling RMON function.

OBJECT-IDENTITY

OBJECT-TYPE

A list of Ethernet statistics entries.

OBJECT-TYPE

A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1

OBJECT-TYPE

The value of this object uniquely identifies this etherStats entry.

OBJECT-TYPE

This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated etherStatsStatus object is equal to valid(1).

OBJECT-TYPE

The entity that configured this entry and is therefore using the resources assigned to it.

OBJECT-TYPE

The status of this etherStats entry.

OBJECT-IDENTITY

OBJECT-TYPE

A list of history control entries.

OBJECT-TYPE

A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyControlInterval.2

OBJECT-TYPE

An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.

OBJECT-TYPE

This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1).

OBJECT-TYPE

The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources.

OBJECT-TYPE

The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1).

OBJECT-TYPE

The entity that configured this entry and is therefore using the resources assigned to it.

OBJECT-TYPE

The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1).

OBJECT-IDENTITY

OBJECT-TYPE

A list of alarm entries.

OBJECT-TYPE

A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8

OBJECT-TYPE

An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device.

OBJECT-TYPE

The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be set short enough that the sampled variable is very unlikely to increase or decrease by more than 2^31 - 1 during a single sampling interval. This object may not be modified if the associated alarmStatus object is equal to valid(1).

OBJECT-TYPE

The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1).

OBJECT-TYPE

The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1).

OBJECT-TYPE

A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).

OBJECT-TYPE

A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).

OBJECT-TYPE

The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).

OBJECT-TYPE

The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).

OBJECT-TYPE

The entity that configured this entry and is therefore using the resources assigned to it.

OBJECT-TYPE

The status of this alarm entry.

OBJECT-IDENTITY

OBJECT-TYPE

A list of events to be generated.

OBJECT-TYPE

A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be named eventLastTimeSent.6

OBJECT-TYPE

An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur.

OBJECT-TYPE

A comment describing this event entry.

OBJECT-TYPE

The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations.

OBJECT-TYPE

If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string.

OBJECT-TYPE

The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this device

OBJECT-TYPE

The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

Enable/Disable Static 802.1x.

OBJECT-TYPE

This object indicates the authentication mode of the device.

OBJECT-TYPE

The authentication method used to authenticate users.

OBJECT-TYPE

When 802.1x disable, this item can decided eap packet be forward or drop.

OBJECT-IDENTITY

OBJECT-TYPE

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

OBJECT-TYPE

The configuration information for an Authenticator Port.

OBJECT-TYPE

A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number.

OBJECT-TYPE

The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine.

OBJECT-TYPE

The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine.

OBJECT-TYPE

The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine.

OBJECT-TYPE

The value of the maxReq constant currently in use by the Backend Authentication state machine.

OBJECT-TYPE

The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine.

OBJECT-TYPE

The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine.

OBJECT-TYPE

The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1).

OBJECT-TYPE

The current value of the controlled Port control parameter for the Port.

OBJECT-TYPE

The current value of the controlled Port control parameter for the Port.

OBJECT-TYPE

The current value of the controlled Port control parameter for the Port.

OBJECT-IDENTITY

OBJECT-TYPE

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

OBJECT-TYPE

The configuration information for an Authenticator Port.

OBJECT-TYPE

The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

OBJECT-TYPE

This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

OBJECT-TYPE

The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthUserName objects must be explicitly set.

OBJECT-IDENTITY

OBJECT-TYPE

A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.

OBJECT-TYPE

The configuration information for an Authenticator Port.

OBJECT-TYPE

A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3.

OBJECT-TYPE

The IP address of the RADIUS server referred to in this table entry.

OBJECT-TYPE

The value is for setting UDP Port.

OBJECT-TYPE

The value is for setting UDP Port.

OBJECT-TYPE

The value is for setting UDP Port.

OBJECT-TYPE

The value is for setting UDP Port.

OBJECT-TYPE

This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.

OBJECT-TYPE

The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set.

OBJECT-IDENTITY

OBJECT-TYPE

The VLAN name of guest VLAN.

OBJECT-TYPE

This object indicates the guest VLAN port members of this device.

OBJECT-TYPE

Used to delete the guest VLAN.

OBJECT-IDENTITY

OBJECT-TYPE

This object can enabled or disabled MAC Notification.

OBJECT-TYPE

This object indicates the time interval in second for trigger the MAC notify message.

OBJECT-TYPE

This object indicates the history size of variation MAC in address table. The default value is 1 .

OBJECT-TYPE

A table to control Loopback detection features either for the entire switch or for each interface in the switch.

OBJECT-TYPE

An entry appears in this table for each interface in the system.

OBJECT-TYPE

The interface index of the port for which the configuration in this entry applies.

OBJECT-TYPE

Provides control to per port enable or disable the loopback detection function. Default is disabled.

OBJECT-IDENTITY

OBJECT-TYPE

Enable/Disable IGMP Multicast Vlan function.

OBJECT-TYPE

Information about the IGMP snooping multicast VLAN table.

OBJECT-TYPE

The entry of igmpMulticastVlanTable.

OBJECT-TYPE

This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.

OBJECT-TYPE

This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.

OBJECT-TYPE

This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.

OBJECT-TYPE

This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.

OBJECT-TYPE

This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.

OBJECT-TYPE

This object can be used to enable or disable the IGMP snooping multicast VLAN.

OBJECT-TYPE

The replacement source IP of this multicast VLAN.

OBJECT-TYPE

This object indicates the status of this entry.

OBJECT-TYPE

The table containing the IGMP snooping multicast VLAN group information

OBJECT-TYPE

Information about the current IGMP snooping multicast VLAN group.

OBJECT-TYPE

This object indicates the VID of the IGMP snooping multicast VLAN group.

OBJECT-TYPE

Specifies the multicast address list for this VLAN.

OBJECT-TYPE

Specifies the multicast address list for this VLAN.

OBJECT-TYPE

This object indicates the status of this entry.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates DHCP relay function is enabled or disabled.

OBJECT-TYPE

This object indicates the maximum number of router hops that the BOOTP packets can cross.

OBJECT-TYPE

This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.

OBJECT-IDENTITY

OBJECT-TYPE

This table indicates the IP address as a destination to forward (relay) DHCP packets to.

OBJECT-TYPE

A list of information indicates the IP address as a destination to forward (relay) DHCP packets to.

OBJECT-TYPE

This object indicates the name of the IP interface.

OBJECT-TYPE

This object indicates the DHCP server IP address.

OBJECT-TYPE

This object indicates the status of this entry.

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates DHCP relay option 82 function is enabled or disabled.

OBJECT-TYPE

This object indicates DHCP relay option 82 Check function is enabled or disabled.

OBJECT-TYPE

This object indicates DHCP relay option 82 policy.

OBJECT-TYPE

This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object.

OBJECT-TYPE

This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If swDHCPRelayOption82RemoteIDType is set to user-defined, a new value can be written to this object.

OBJECT-IDENTITY

OBJECT-TYPE

This object indicates DHCP local relay function of VLAN is enabled or disabled.

OBJECT-TYPE

This table indicates the IP address as a destination to forward (local relay) DHCP packets to.

OBJECT-TYPE

A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to.

OBJECT-TYPE

This object displays the current VLAN ID of the device.

OBJECT-TYPE

This object indicates DHCP local relay function of VLAN is enabled or disabled.

OBJECT-IDENTITY

OBJECT-TYPE

The smart console utility's IP address is used to recive trap events.

OBJECT-TYPE

Enable/Disable system trap events in the switch system.

OBJECT-TYPE

Enable/Disable fiber port trap event in the system.

OBJECT-TYPE

Enable/Disable twisted port trap event in the system.

OBJECT-TYPE

Enable/Disable RSTP state change trap event in the system.

OBJECT-TYPE

Enable/Disable firmware upgrading trap event in the system.

OBJECT-TYPE

Enable/Disable trap event in the system.

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

OBJECT-TYPE

This object is for enabling or disabling send gratuitous trap when IP address conflicted in the network.

OBJECT-IDENTITY

OBJECT-TYPE

This object is used for enabling or disabling LLDP in the system.

OBJECT-TYPE

The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpMessageTxInterval * lldpMessageTxHoldMultiplier))

OBJECT-TYPE

This object is used for LLDP packet update frequency. The timer in units of seconds.

OBJECT-TYPE

This object is used for LLDP Reinitialization Delay. The timer in units of seconds.

OBJECT-TYPE

The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB. The recommended value for the lldpTxDelay is set by the following formula: 1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval).

OBJECT-TYPE

A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will be transmitted on the member ports of the lldpManAddrPortsTxEnable. The default value for lldpConfigManAddrPortsTxEnable object is empty binary string, which means no ports are specified for advertising indicated management address instance.

OBJECT-TYPE

The table that controls LLDP frame transmission on individual ports.

OBJECT-TYPE

LLDP configuration information for a particular port. This configuration parameter controls the transmission and the reception of LLDP frames on those ports whose rows are created in this table.

OBJECT-TYPE

The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The value of this object is used as a port index to the lldpPortConfigTable.

OBJECT-TYPE

The administratively desired status of the local LLDP agent. If the associated lldpPortConfigAdminStatus object has a value of 'txOnly(1)', then LLDP agent will transmit LLDP frames on this port and it will not store any information about the remote systems connected. If the associated lldpPortConfigAdminStatus object has a value of 'rxOnly(2)', then the LLDP agent will receive, but it will not transmit LLDP frames on this port. If the associated lldpPortConfigAdminStatus object has a value of 'txAndRx(3)', then the LLDP agent will transmit and receive LLDP frames on this port. If the associated lldpPortConfigAdminStatus object has a value of 'disabled(4)', then LLDP agent will not transmit or receive LLDP frames on this port. If there is remote systems information which is received on this port and stored in other tables, before the port's lldpPortConfigAdminStatus becomes disabled, then the information will naturally age out.

OBJECT-TYPE

The lldpPortConfigNotificationEnable controls, on a per port basis, whether or not notifications from the agent are enabled. The value true(1) means that notifications are enabled; the value false(2) means that they are not.

OBJECT-TYPE

The lldpPortConfigTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to a TLV type associated with a specific optional TLV. It should be noted that the organizationally-specific TLVs are excluded from the lldpTLVsTxEnable bitmap. LLDP Organization Specific Information Extension MIBs should have similar configuration object to control transmission of their organizationally defined TLVs. The bit 'portDesc(0)' indicates that LLDP agent should transmit 'Port Description TLV'. The bit 'sysName(1)' indicates that LLDP agent should transmit 'System Name TLV'. The bit 'sysDesc(2)' indicates that LLDP agent should transmit 'System Description TLV'. The bit 'sysCap(3)' indicates that LLDP agent should transmit 'System Capabilities TLV'. There is no bit reserved for the management address TLV type since transmission of management address TLVs are controlled by another object, lldpConfigManAddrTable. The default value for lldpPortConfigTLVsTxEnable object is empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table that controls selection of LLDP TLVs to be transmitted on individual ports.

OBJECT-TYPE

LLDP configuration information that controls the transmission of IEEE 802.3 organizationally defined TLVs on LLDP transmission capable ports. This configuration object augments the lldpPortConfigEntry of the LLDP-MIB, therefore it is only present along with the port configuration defined by the associated lldpPortConfigEntry entry. Each active lldpXdot3PortConfigEntry must be from non-volatile storage (along with the corresponding lldpPortConfigEntry) after a re-initialization of the management system.

OBJECT-TYPE

The lldpXdot3PortConfigTLVsTxEnable, defined as a bitmap, includes the IEEE 802.3 organizationally defined set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to an IEEE 802.3 subtype associated with a specific IEEE 802.3 optional TLV. The bit 0 is not used since there is no corresponding subtype. The bit 'macPhyConfigStatus(0)' indicates that LLDP agent should transmit 'MAC/PHY configuration/status TLV'. The bit 'powerViaMDI(1)' indicates that LLDP agent should transmit 'Power via MDI TLV'. The bit 'linkAggregation(2)' indicates that LLDP agent should transmit 'Link Aggregation TLV'. The bit 'maxFrameSize(3)' indicates that LLDP agent should transmit 'Maximum-frame-size TLV'. The default value for lldpXdot3PortConfigTLVsTxEnable object is an empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains one row per port of Ethernet port information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.

OBJECT-TYPE

Information about a particular port component.

OBJECT-TYPE

The truth value used to indicate whether the given port (associated with the local system) supports Auto-negotiation.

OBJECT-TYPE

The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the local system.

OBJECT-TYPE

This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the local system.

OBJECT-TYPE

An integer value that indicates the operational MAU type of the given port on the local system. This object contains the integer value derived from the list position of the corresponding dot3MauType as listed in IETF RFC 3636 (or subsequent revisions) and is equal to the last number in the respective dot3MauType OID. For example, if the ifMauType object is dot3MauType1000BaseTHD which corresponds to {dot3MauType 29}, the numerical value of this field will be 29. For MAU types not listed in RFC 3636 (or subsequent revisions), the value of this field shall be set to zero.

OBJECT-TYPE

This table contains one row per port of power ethernet information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.

OBJECT-TYPE

Information about a particular port component.

OBJECT-TYPE

The value that identifies the port Class of the given port associated with the local system.

OBJECT-TYPE

The truth value used to indicate whether the MDI power is supported on the given port associated with the local system.

OBJECT-TYPE

The truth value used to identify whether MDI power is enabled on the given port associated with the local system.

OBJECT-TYPE

The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair selection can be controlled on the given port associated with the local system.

OBJECT-TYPE

This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the local system.

OBJECT-TYPE

This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the local system.

OBJECT-TYPE

This table contains one row per port of link aggregation information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.

OBJECT-TYPE

Link Aggregation information about a particular port component.

OBJECT-TYPE

The bitmap value contains the link aggregation capabilities and the current aggregation status of the link.

OBJECT-TYPE

This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port component in link aggregation. If the port is not in link aggregation state and/or it does not support link aggregation, this value should be set to zero.

OBJECT-TYPE

This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.

OBJECT-TYPE

Maximum Frame Size information about a particular port component.

OBJECT-TYPE

An integer value indicating the maximum supported frame size in octets on the given port of the local system.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains Ethernet port information (as a part of the LLDP 802.3 organizational extension) of the remote system.

OBJECT-TYPE

Information about a particular physical network connection.

OBJECT-TYPE

The truth value used to indicate whether the given port (associated with remote system) supports Auto-negotiation.

OBJECT-TYPE

The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the remote system.

OBJECT-TYPE

This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the remote system.

OBJECT-TYPE

An integer value that indicates the operational MAU type of the sending device. This object contains the integer value derived from the list position of the corresponding dot3MauType as listed in in IETF RFC 3636 (or subsequent revisions) and is equal to the last number in the respective dot3MauType OID. For example, if the ifMauType object is dot3MauType1000BaseTHD which corresponds to {dot3MauType 29}, the numerical value of this field will be 29. For MAU types not listed in RFC 3636 (or subsequent revisions), the value of this field shall be set to zero.

OBJECT-TYPE

This table contains Ethernet power information (as a part of the LLDP 802.3 organizational extension) of the remote system.

OBJECT-TYPE

Information about a particular physical network connection.

OBJECT-TYPE

The value that identifies the port Class of the given port associated with the remote system.

OBJECT-TYPE

The truth value used to indicate whether the MDI power is supported on the given port associated with the remote system.

OBJECT-TYPE

The truth value used to identify whether MDI power is enabled on the given port associated with the remote system.

OBJECT-TYPE

The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair selection can be controlled on the given port associated with the remote system.

OBJECT-TYPE

This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the remote system.

OBJECT-TYPE

This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the remote system.

OBJECT-TYPE

This table contains port link aggregation information (as a part of the LLDP 802.3 organizational extension) of the remote system.

OBJECT-TYPE

Link Aggregation information about remote system's port component.

OBJECT-TYPE

The bitmap value contains the link aggregation capabilities and the current aggregation status of the link.

OBJECT-TYPE

This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port component associated with the remote system. If the remote port is not in link aggregation state and/or it does not support link aggregation, this value should be zero.

OBJECT-TYPE

This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) of the remote system.

OBJECT-TYPE

Maximum Frame Size information about a particular port component.

OBJECT-TYPE

An integer value indicating the maximum supported frame size in octets on the port component associated with the remote system.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table that controls selection of LLDP Port VLAN-ID TLVs to be transmitted on individual ports.

OBJECT-TYPE

LLDP configuration information that controls the transmission of IEEE 802.1 organizationally defined Port VLAN-ID TLV on LLDP transmission capable ports. This configuration object augments the lldpPortConfigEntry of the LLDP-MIB, therefore it is only present along with the port configuration defined by the associated lldpPortConfigEntry entry. Each active lldpConfigEntry must be restored from non-volatile storage (along with the corresponding lldpPortConfigEntry) after a re-initialization of the management system.

OBJECT-TYPE

The lldpXdot1ConfigPortVlanTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined port VLAN TLV transmission is allowed on a given LLDP transmission capable port. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

OBJECT-TYPE

The table that controls selection of LLDP VLAN name TLV instances to be transmitted on individual ports.

OBJECT-TYPE

LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System VLAN name instance will be transmitted. This configuration object augments the lldpLocVlanEntry, therefore it is only present along with the VLAN Name instance contained in the associated lldpLocVlanNameEntry entry. Each active lldpXdot1ConfigVlanNameEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocVlanNameEntry) after a re-initialization of the management system.

OBJECT-TYPE

The boolean value that indicates whether the corresponding Local System VLAN name instance will be transmitted on the port defined by the given lldpXdot1LocVlanNameEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

OBJECT-TYPE

The table that controls selection of LLDP Port and Protocol VLAN ID TLV instances to be transmitted on individual ports.

OBJECT-TYPE

LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol VLAN instance will be transmitted. This configuration object augments the lldpXdot1LocVlanEntry, therefore it is only present along with the Port and Protocol VLAN ID instance contained in the associated lldpXdot1LocVlanEntry entry. Each active lldpXdot1ConfigProtoVlanEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtoVlanEntry) after a re-initialization of the management system.

OBJECT-TYPE

The boolean value that indicates whether the corresponding Local System Port and Protocol VLAN instance will be transmitted on the port defined by the given lldpXdot1LocProtoVlanEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

OBJECT-TYPE

The table that controls selection of LLDP Protocol TLV instances to be transmitted on individual ports.

OBJECT-TYPE

LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol instance will be transmitted. This configuration object augments the lldpXdot1LocProtoEntry, therefore it is only present along with the Protocol instance contained in the associated lldpXdot1LocProtoEntry entry. Each active lldpXdot1ConfigProtocolEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtocolEntry) after a re-initialization of the management system.

OBJECT-TYPE

The boolean value that indicates whether the corresponding Local System Protocol Identity instance will be transmitted on the port defined by the given lldpXdot1LocProtocolEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains one row per port for IEEE 802.1 organizationally defined LLDP extension on the local system known to this agent.

OBJECT-TYPE

Information about IEEE 802.1 organizationally defined LLDP extension.

OBJECT-TYPE

The integer value used to identify the port's VLAN identifier associated with the local system. A value of zero shall be used if the system either does not know the PVID or does not support port-based VLAN operation.

OBJECT-TYPE

This table contains one or more rows per Port and Protocol VLAN information about the local system.

OBJECT-TYPE

Port and protocol VLAN ID Information about a particular port component. There may be multiple port and protocol VLANs, identified by a particular lldpXdot1LocProtoVlanId, configured on the given port.

OBJECT-TYPE

The integer value used to identify the port and protocol VLANs associated with the given port associated with the local system. A value of zero shall be used if the system either does not know the protocol VLAN ID (PPVID) or does not support port and protocol VLAN operation.

OBJECT-TYPE

The truth value used to indicate whether the given port (associated with the local system) supports port and protocol VLANs.

OBJECT-TYPE

The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the local system.

OBJECT-TYPE

This table contains one or more rows per IEEE 802.1Q VLAN name information on the local system known to this agent.

OBJECT-TYPE

VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1LocVlanId, configured on the given port.

OBJECT-TYPE

The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port is compatible.

OBJECT-TYPE

The string value used to identify VLAN name identified by the Vlan Id associated with the given port on the local system. This object should contain the value of the dot1QVLANStaticName object (defined in IETF RFC 2674) identified with the given lldpXdot1LocVlanId.

OBJECT-TYPE

This table contains one or more rows per protocol identity information on the local system known to this agent.

OBJECT-TYPE

Information about particular protocols that are accessible through the given port component. There may be multiple protocols, identified by particular lldpXdot1ProtocolIndex, and lldpLocPortNum.

OBJECT-TYPE

This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity.

OBJECT-TYPE

The octet string value used to identify the protocols associated with the given port of the local system.

OBJECT-IDENTITY

OBJECT-TYPE

This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpXdot1RemEntry is present for each local port, or it may choose to maintain multiple lldpXdot1RemEntries for the same local port.

OBJECT-TYPE

Information about a particular port component.

OBJECT-TYPE

The integer value used to identify the port's VLAN identifier associated with the remote system. if the remote system either does not know the PVID or does not support port-based VLAN operation, the value of lldpXdot1RemPortVlanId should be zero.

OBJECT-TYPE

This table contains one or more rows per Port and Protocol VLAN information about the remote system, received on the given port.

OBJECT-TYPE

Port and protocol VLAN name Information about a particular port component. There may be multiple protocol VLANs, identified by a particular lldpXdot1RemProtoVlanId, configured on the remote system.

OBJECT-TYPE

The integer value used to identify the port and protocol VLANs associated with the given port associated with the remote system. If port and protocol VLANs are not supported on the given port associated with the remote system, or if the port is not enabled with any port and protocol VLAN, the value of lldpXdot1RemProtoVlanId should be zero.

OBJECT-TYPE

The truth value used to indicate whether the given port (associated with the remote system) is capable of supporting port and protocol VLANs.

OBJECT-TYPE

The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the remote system.

OBJECT-TYPE

This table contains one or more rows per IEEE 802.1Q VLAN name information about the remote system, received on the given port.

OBJECT-TYPE

VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1RemVlanId, received on the given port.

OBJECT-TYPE

The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port of the remote system is compatible.

OBJECT-TYPE

The string value used to identify VLAN name identified by the VLAN Id associated with the remote system.

OBJECT-TYPE

This table contains one or more rows per protocol information about the remote system, received on the given port.

OBJECT-TYPE

Protocol information about a particular port component. There may be multiple protocols, identified by a particular lldpXdot1ProtocolIndex, received on the given port.

OBJECT-TYPE

This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity.

OBJECT-TYPE

The octet string value used to identify the protocols associated with the given port of remote system.

OBJECT-IDENTITY

OBJECT-IDENTITY

OBJECT-TYPE

A table to CPUInterfaceFilter profile .

OBJECT-TYPE

Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID.

OBJECT-TYPE

The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter. The user only allow to create user-defined CPUInterfaceFilter ID. And system-defined CPUInterfaceFilter is read only.

OBJECT-TYPE

The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule,

OBJECT-TYPE

The number of rules in this profile.

OBJECT-TYPE

Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 (MSB) ------------------------------------------- The value is in Hex format.

OBJECT-TYPE

The CPUInterfaceFilter Profile destination MAC address mask. If DST_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleDstMacAddr, to caculate a range of MAC address which is really care.

OBJECT-TYPE

The CPUInterfaceFilter Profile source MAC address mask. If SRC_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.

OBJECT-TYPE

Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.

OBJECT-TYPE

The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.

OBJECT-TYPE

The CPUInterfaceFilter Profile destination IP address mask. If DST_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

OBJECT-TYPE

The CPUInterfaceFilter Profile source IP address mask. If SRC_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'

OBJECT-TYPE

The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.

OBJECT-TYPE

The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.

OBJECT-TYPE

This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of cpuFilterProfileType, cpuFilterProfileMask and ProtocolType are not conflicted.

OBJECT-IDENTITY

OBJECT-TYPE

A table to configure L2 filter rules in the system.

OBJECT-TYPE

Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.

OBJECT-TYPE

L2 Filter rule ID.

OBJECT-TYPE

CPUInterfaceFilter Profile ID which this rule join.