MIBs Depot

DES-1210-26MEbx

Registered at
1.3.6.1.4.1.171.10.75.16
Last updated
2015-06-03 00:00
Organization
DES-1210-26-BX-10-01-017.mib
Revisions
2015-06-03 00:00, 2015-04-16 00:00, 2014-03-06 00:00
Namespace
dlink
Source file
DES-1210-26MEbx
Digest
sha256:b83c1c3aed2969622cd6d22115d86afb3b097fd8921978331d86ba3350e818c2

Description

In order to pass the web www.simpleweb.org to verify severity level 3, which must be change the SYNTAX of mib file.

Imports

FromSymbols
BRIDGE-MIBdot1dBasePort, dot1dBasePortEntry, dot1dBridge
IANA-ADDRESS-FAMILY-NUMBERS-MIBAddressFamilyNumbers
IF-MIBInterfaceIndex, InterfaceIndexOrZero
INET-ADDRESS-MIBInetAddress
Q-BRIDGE-MIBVlanId
SNMP-FRAMEWORK-MIBSnmpAdminString, SnmpEngineID, SnmpSecurityLevel
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso
SNMPv2-TCDisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

BRIDGE-MIB
DES-1210-26MEbx
IANA-ADDRESS-FAMILY-NUMBERS-MIB
IANAifType-MIB
IF-MIB
INET-ADDRESS-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB

Textual conventions

NameOIDSyntaxAccessStatus
BridgeId
TEXTUAL-CONVENTION
The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to refer to a bridge in a unique fashion (typically, the numerically smallest MAC address of all ports on the bridge). Several objects in this MIB module represent values of timers used by the Spanning Tree Protocol. In this MIB, these timers have values in units of hundreths of a second (i.e. 1/100 secs). These timers, when stored in a Spanning Tree Protocol's BPDU, are in units of 1/256 seconds. Note, however, that 802.1D-1990 specifies a settable granularity of no more than 1 second for these timers. To avoid ambiguity, a data type is defined here as a textual convention and all representation of these timers in this MIB module are defined using this data type. An algorithm is also defined for converting between the different units, to ensure a timer's value is not distorted by multiple conversions.
current
Ipv6Address
TEXTUAL-CONVENTION
This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.
current
LacpKey
TEXTUAL-CONVENTION
The Actor or Partner Key value (0..65535).
current
LldpLinkAggStatusMap
TEXTUAL-CONVENTION
This TC describes the link aggregation status. The bit 'aggCapable(0)' indicates the link is capable of being aggregated. The bit 'aggEnabled(1)' indicates the link is currently in aggregation.
current
LldpManAddress
TEXTUAL-CONVENTION
The value of a management address associated with the LLDP agent that may be used to reach higher layer entities to assist discovery by network management. It should be noted that appropriate security credentials, such as SNMP engineId, may be required to access the LLDP agent using a management address. These necessary credentials should be known by the network management and the objects associated with the credentials are not included in the LLDP agent.
current
LldpPortNumber
TEXTUAL-CONVENTION
Each port contained in the chassis (that is known to the LLDP agent) is uniquely identified by a port number. A port number has no mandatory relationship to an InterfaceIndex object (of the interfaces MIB, IETF RFC 2863). If the LLDP agent is a IEEE 802.1D, IEEE 802.1Q bridge, the LldpPortNumber will have the same value as the dot1dBasePort object (defined in IETF RFC 1493) associated corresponding bridge port. If the system hosting LLDP agent is not an IEEE 802.1D or an IEEE 802.1Q bridge, the LldpPortNumber will have the same value as the corresponding interface's InterfaceIndex object. Port numbers should be in the range of 1 and 4096 since a particular port is also represented by the corresponding port number bit in LldpPortList.
current
LldpPowerPortClass
TEXTUAL-CONVENTION
This TC describes the Power over Ethernet (PoE) port class.
current
OwnerString
TEXTUAL-CONVENTION
This data type is used to model an administratively assigned name of the owner of a resource. Implementations must accept values composed of well-formed NVT ASCII sequences. In addition, implementations should accept values composed of well-formed UTF-8 sequences. It is suggested that this name contain one or more of the following: IP address, management station name, network manager's name, location, or phone number. In some cases the agent itself will be the owner of an entry. In these cases, this string shall be set to a string starting with 'monitor'. SNMP access control is articulated entirely in terms of the contents of MIB views; access to a particular SNMP object instance depends only upon its presence or absence in a particular MIB view and never upon its value or the value of related object instances. Thus, objects of this type afford resolution of resource contention only among cooperating managers; they realize no access control function with respect to uncooperative parties.
current
PortLaMode
TEXTUAL-CONVENTION
Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. static(2) - force the port to enable channeling. disable(3) - channeling is disabled.
current
PortList
TEXTUAL-CONVENTION
Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
current
RmonStatus
TEXTUAL-CONVENTION
The status of a table entry. Setting this object to the value invalid(4) has the effect of invalidating the corresponding entry. That is, it effectively disassociates the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries currently not in use. Proper interpretation of such entries requires examination of the relevant RmonStatus object. An existing instance of this object cannot be set to createRequest(2). This object may only be set to createRequest(2) when this instance is created. When this object is created, the agent may wish to create supplemental object instances with default values to complete a conceptual row in this table. Because the creation of these default objects is entirely at the option of the agent, the manager must not assume that any will be created, but may make use of any that are created. Immediately after completing the create operation, the agent must set this object to underCreation(3). When in the underCreation(3) state, an entry is allowed to exist in a possibly incomplete, possibly inconsistent state, usually to allow it to be modified in multiple PDUs. When in this state, an entry is not fully active. Entries shall exist in the underCreation(3) state until the management station is finished configuring the entry and sets this object to valid(1) or aborts, setting this object to invalid(4). If the agent determines that an entry has been in the underCreation(3) state for an abnormally long time, it may decide that the management station has crashed. If the agent makes this decision, it may set this object to invalid(4) to reclaim the entry. A prudent agent will understand that the management station may need to wait for human input and will allow for that possibility in its determination of this abnormally long period. An entry in the valid(1) state is fully configured and consistent and fully represents the configuration or operation such a row is intended to represent. For example, it could be a statistical function that is configured and active, or a filter that is available in the list of filters processed by the packet capture process. A manager is restricted to changing the state of an entry in the following ways: To: valid createRequest underCreation invalid From: valid OK NO OK OK createRequest N/A N/A N/A N/A underCreation OK NO OK OK invalid NO NO NO OK nonExistent NO OK NO OK In the table above, it is not applicable to move the state from the createRequest state to any other state because the manager will never find the variable in that state. The nonExistent state is not a value of the enumeration, rather it means that the entryStatus variable does not exist at all. An agent may allow an entryStatus variable to change state in additional ways, so long as the semantics of the states are followed. This allowance is made to ease the implementation of the agent and is made despite the fact that managers should never exercise these additional state transitions.
current
Timeout
TEXTUAL-CONVENTION
A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: floor = quotient [ignore remainder] n is the value in 1/100 second units b is the value in 1/256 second units To convert the value from 1/256 second units back to 1/100 seconds, the following algorithm should be used: n = ceiling( (b * 100) / 256) where: ceiling = quotient [if remainder is 0], or quotient + 1 [if remainder is non-zero] n is the value in 1/100 second units b is the value in 1/256 second units Note: it is important that the arithmetic operations are done in the order specified (i.e., multiply first, divide second).
current
VlanIndex
TEXTUAL-CONVENTION
A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see VlanId textual convention). If the value is greater than 4095 then it represents a VLAN with scope local to the particular agent, i.e. one without a global VLAN-ID assigned to it. Such VLANs are outside the scope of IEEE 802.1Q but it is convenient to be able to manage them in the same way using this MIB.
current

Objects

NameOIDSyntaxAccessStatus
des_1210_26me
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16
companySystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.1
sysSwitchName
OBJECT-TYPE
System name used for identification of the device. The following characters are allowed to input. 0 ~ 9 / a ~ z / A ~ Z Special character: ( ) V + _ = .
1.3.6.1.4.1.171.10.75.16.1.1.1DisplayString (SIZE(1..20))read-writecurrent
sysHardwareVersion
OBJECT-TYPE
Version number of the Hardware.
1.3.6.1.4.1.171.10.75.16.1.1.2DisplayString (SIZE(1..15))read-onlycurrent
sysFirmwareVersion
OBJECT-TYPE
Version number of the Firmware.
1.3.6.1.4.1.171.10.75.16.1.1.3DisplayString (SIZE(1..15))read-onlycurrent
sysLoginTimeoutInterval
OBJECT-TYPE
This time interval is used to count the time and logout web interface automatically.
1.3.6.1.4.1.171.10.75.16.1.1.4Integer32 (3..30)read-writecurrent
sysLocationName
OBJECT-TYPE
The location name of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string.
1.3.6.1.4.1.171.10.75.16.1.1.5DisplayString (SIZE(1..20))read-writecurrent
sysGroupInterval
OBJECT-TYPE
Group Interval is used to send D-link Discover packet to D-link SmartConsole Utility frequency. The timer in units of seconds. Set value 0 to disable group Interval.
1.3.6.1.4.1.171.10.75.16.1.1.6Integer32 (0 | 120..1225)read-writecurrent
sysSafeGuardEnable
OBJECT-TYPE
This object is used to set Safeguard Enable\Disable.
1.3.6.1.4.1.171.10.75.16.1.1.8INTEGER {enable(1), disable(2)}read-writecurrent
sysRestart
OBJECT-TYPE
This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'.
1.3.6.1.4.1.171.10.75.16.1.1.9TruthValueread-writecurrent
sysSave
OBJECT-TYPE
This object is used to save Configuration , value 1 save config_1 , value 2 is not in process , value 3 is save config_1 and value 4 is save config_2.
1.3.6.1.4.1.171.10.75.16.1.1.10INTEGER {true(1), false(2), config-1(3), config-2(4)}read-writecurrent
sysJumboFrameEnable
OBJECT-TYPE
Gigabit Web Smart Switches support jumbo frames (frames larger than the Ethernet frame size of 1522 bytes) of up to 10,000 bytes (tagged). Default jumbo frame is disabled.
1.3.6.1.4.1.171.10.75.16.1.1.12INTEGER {enable(1), disable(2)}read-writecurrent
sysPortCtrlTable
OBJECT-TYPE
A table to control the port specific parameters of the device like speed, duplex mode, etc.
1.3.6.1.4.1.171.10.75.16.1.1.13not-accessiblecurrent
sysPortCtrlEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.
1.3.6.1.4.1.171.10.75.16.1.1.13.1not-accessiblecurrent
sysPortCtrlIndex
OBJECT-TYPE
Interface index of the port for the configuration in this entry applies.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.1Integer32 (1..65535)read-onlycurrent
sysPortCtrlMediumType
OBJECT-TYPE
This object indicates the port type: fiber 1G/100M or copper.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.2INTEGER {copper(100), fiber(101)}read-onlycurrent
sysPortCtrlSpeed
OBJECT-TYPE
Configures interface speed.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.3INTEGER {rate1000M-Full(1), rate100M-Full(2), rate100M-Half(3), rate10M-Full(4), rate10M-Half(5), auto(6), disable(7)}read-writecurrent
sysPortCtrlOperStatus
OBJECT-TYPE
The port's operating speed state.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.4INTEGER {down(1), rate1000M-Full(2), rate100M-Full(3), rate100M-Half(4), rate10M-Full(5), rate10M-Half(6), rate10G-Full(7)}read-onlycurrent
sysPortCtrlMDI
OBJECT-TYPE
Configures interface auto/mdi/mdix mode. The default setting is Auto.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.5INTEGER {auto(1), mdi(2), mdix(3)}read-writecurrent
sysPortCtrlFlowControl
OBJECT-TYPE
Enables / disables flow control for the interface.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.6INTEGER {enable(1), disable(2)}read-writecurrent
sysPortCtrlFlowControlOper
OBJECT-TYPE
The link parner negotiate port's operating flow control state.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.7INTEGER {enabled(1), disabled(2)}read-onlycurrent
sysPortCtrlType
OBJECT-TYPE
The port's media type.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.8INTEGER {fastethernet(1), gigabitethernet(2), fiberwith100Base-and-1000BaseSFPModule(3)}read-onlycurrent
sysPortCtrlCapability
OBJECT-TYPE
The port's capability advertised.
1.3.6.1.4.1.171.10.75.16.1.1.13.1.9Bits {rate10-half(0), rate10-full(1), rate100-half(2), rate100-full(3), reserve(4), rate1000-full(5)}read-writecurrent
sysPortDescriptionTable
OBJECT-TYPE
The port description table.
1.3.6.1.4.1.171.10.75.16.1.1.14not-accessiblecurrent
sysPortDescriptionEntry
OBJECT-TYPE
The port description entry.
1.3.6.1.4.1.171.10.75.16.1.1.14.1not-accessiblecurrent
sysPortDescIndex
OBJECT-TYPE
This object indicates the port index.
1.3.6.1.4.1.171.10.75.16.1.1.14.1.1INTEGER (1..255)read-onlycurrent
sysPortDescMediumType
OBJECT-TYPE
This object indicates the port type: fiber 1G/100M or copper.
1.3.6.1.4.1.171.10.75.16.1.1.14.1.2INTEGER {copper(100), fiber(101)}read-onlycurrent
sysPortDescString
OBJECT-TYPE
This object indicates the port description.
1.3.6.1.4.1.171.10.75.16.1.1.14.1.3DisplayString (SIZE(0..32))read-writecurrent
sysPortUpLinkTime
OBJECT-TYPE
This object indicates the port link up time.
1.3.6.1.4.1.171.10.75.16.1.1.14.1.4DisplayString (SIZE(0..32))read-onlycurrent
sysPortErrTable
OBJECT-TYPE
The port error table.
1.3.6.1.4.1.171.10.75.16.1.1.15not-accessiblecurrent
sysPortErrEntry
OBJECT-TYPE
A list of information for the err port of the device.
1.3.6.1.4.1.171.10.75.16.1.1.15.1not-accessiblecurrent
sysPortErrPortIndex
OBJECT-TYPE
This object indicates the module's port number.(1..Max port number in the module)
1.3.6.1.4.1.171.10.75.16.1.1.15.1.1INTEGER (1..255)read-onlycurrent
sysPortErrPortState
OBJECT-TYPE
This object decides whether the port state is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.1.15.1.2INTEGER {disabled(1), enabled(2)}read-onlycurrent
sysPortErrPortStatus
OBJECT-TYPE
This object decides whether the PortStatus is err-disabled.
1.3.6.1.4.1.171.10.75.16.1.1.15.1.3INTEGER {other(1), err-disabled(2)}read-onlycurrent
sysPortErrPortReason
OBJECT-TYPE
This object decides whether the PortStatus is LBD.
1.3.6.1.4.1.171.10.75.16.1.1.15.1.4INTEGER {lbd(1)}read-onlycurrent
sysDhcpAutoConfiguration
OBJECT-TYPE
This object indicates auto config is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.1.16INTEGER {enable(1), disable(2)}read-writecurrent
sysWebState
OBJECT-TYPE
This object is for Enabled(1) or Disabled(2) Web state in the system.
1.3.6.1.4.1.171.10.75.16.1.1.17INTEGER {enabled(1), disabled(2)}read-writecurrent
sysWebPortNumber
OBJECT-TYPE
Web Server Port Number.
1.3.6.1.4.1.171.10.75.16.1.1.18Integer32 (1..65535)read-writecurrent
sysARPAgingTime
OBJECT-TYPE
This object is for ARP aging time.
1.3.6.1.4.1.171.10.75.16.1.1.19INTEGER (0..65535)read-writecurrent
sysMACAgingTime
OBJECT-TYPE
This object is for MAC aging time.
1.3.6.1.4.1.171.10.75.16.1.1.20INTEGER (10..1000000)read-writecurrent
baudRateConfiguration
OBJECT-TYPE
To set SerialPort baud-rate configuration.
1.3.6.1.4.1.171.10.75.16.1.1.21INTEGER {baudrate9600(9600), baudrate19200(19200), baudrate38400(38400), baudrate115200(115200)}read-writecurrent
autologoutConfiguration
OBJECT-TYPE
To set SerialPort auto-logout-time configuration.
1.3.6.1.4.1.171.10.75.16.1.1.22INTEGER {logouttimenever(0), logouttime2mins(120), logouttime5mins(300), logouttime10mins(600), logouttime15mins(900)}read-writecurrent
telnetsettingManagementOnOff
OBJECT-TYPE
Enable/Disable management Telnetsetting mechanism.
1.3.6.1.4.1.171.10.75.16.1.1.23INTEGER {enabled(1), disabled(2)}read-writecurrent
telnetUDPPort
OBJECT-TYPE
The value is for setting telnet's UDP Port.
1.3.6.1.4.1.171.10.75.16.1.1.24INTEGER (1..65535)read-writecurrent
autoRefreshConfiguration
OBJECT-TYPE
To set the WEB panel auto refresh timer.
1.3.6.1.4.1.171.10.75.16.1.1.25INTEGER {refreshimenever(0), refreshtime10secs(1), refreshtime30secs(2), refreshtime1min(3), refreshtime5mins(4)}read-writecurrent
floodfdbOnOff
OBJECT-TYPE
To set enable status for flood fdb.
1.3.6.1.4.1.171.10.75.16.1.1.26INTEGER {enabled(1), disabled(2)}read-writecurrent
sysContactName
OBJECT-TYPE
To set system contact name.
1.3.6.1.4.1.171.10.75.16.1.1.27DisplayString (SIZE(1..128))read-writecurrent
sysDhcpAutoConfigTimeout
OBJECT-TYPE
To set dhcp auto config timeout.
1.3.6.1.4.1.171.10.75.16.1.1.28INTEGER (1..65535)read-writecurrent
sysCommandLogging
OBJECT-TYPE
To set enable status for CommandLogging.
1.3.6.1.4.1.171.10.75.16.1.1.29INTEGER {enable(1), disable(2)}read-writecurrent
sysSerialNumber
OBJECT-TYPE
To get the serial number.
1.3.6.1.4.1.171.10.75.16.1.1.30DisplayString (SIZE(1..13))read-onlycurrent
sysFirmwareInfomation
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.1.31
sysVersion
OBJECT-TYPE
The version of firmware information.
1.3.6.1.4.1.171.10.75.16.1.1.31.1DisplayString (SIZE(1..15))read-onlycurrent
sysSize
OBJECT-TYPE
The size of firmware information.
1.3.6.1.4.1.171.10.75.16.1.1.31.2Integer32read-onlycurrent
sysUpdateTime
OBJECT-TYPE
The Update Time of firmware information.
1.3.6.1.4.1.171.10.75.16.1.1.31.3DisplayString (SIZE(1..20))read-onlycurrent
sysFromIP
OBJECT-TYPE
The IP address of firmware information.
1.3.6.1.4.1.171.10.75.16.1.1.31.4IpAddressread-onlycurrent
sysUser
OBJECT-TYPE
The user of firmware infomation.
1.3.6.1.4.1.171.10.75.16.1.1.31.5DisplayString (SIZE(1..9))read-onlycurrent
sysType
OBJECT-TYPE
The type of firmware infomation.
1.3.6.1.4.1.171.10.75.16.1.1.31.6INTEGER {unknown(-1), console(1), telnet(2), ssh(3), web(4)}read-onlycurrent
sysBootupConfigID
OBJECT-TYPE
To get/set bootup config ID.
1.3.6.1.4.1.171.10.75.16.1.1.33INTEGER (1..2)read-writecurrent
sysDhcpAutoImage
OBJECT-TYPE
This object indicates auto image is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.1.34INTEGER {enable(1), disable(2)}read-writecurrent
sysPortMediaTypeTable
OBJECT-TYPE
A table to control the port specific parameters of the device like speed, Vendor name, etc.
1.3.6.1.4.1.171.10.75.16.1.1.36not-accessiblecurrent
sysPortMediaTypeEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.
1.3.6.1.4.1.171.10.75.16.1.1.36.1not-accessiblecurrent
sysPortMediaTypeIndex
OBJECT-TYPE
Interface index of the port for the configuration in this entry applies.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.1Integer32 (1..65535)read-onlycurrent
sysPortMediaType
OBJECT-TYPE
This object indicates the port type: fiber 1G/100M or copper.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.2INTEGER {copper(100), fiber(101)}read-onlycurrent
sysPortType
OBJECT-TYPE
Configures interface speed.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.3INTEGER {rate100M(1), rate1000M(2), rate10G(3)}read-onlycurrent
sysPortMediaTypeVendorName
OBJECT-TYPE
The port's VendorName.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.4DisplayString (SIZE(1..20))read-onlycurrent
sysPortMediaTypeOui
OBJECT-TYPE
The port's Oui.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.5DisplayString (SIZE(1..20))read-onlycurrent
sysPortMediaTypePn
OBJECT-TYPE
The port's Pn.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.6DisplayString (SIZE(1..20))read-onlycurrent
sysPortMediaTypeRev
OBJECT-TYPE
The port's Rev.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.7DisplayString (SIZE(1..20))read-onlycurrent
sysPortMediaTypeSn
OBJECT-TYPE
The port's Sn.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.8DisplayString (SIZE(1..20))read-onlycurrent
sysPortMediaTypeDateCode
OBJECT-TYPE
The port's DateCode.
1.3.6.1.4.1.171.10.75.16.1.1.36.1.9DisplayString (SIZE(1..20))read-onlycurrent
companyIpifGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.2
ipv4sysIpAddrCfgMode
OBJECT-TYPE
Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.
1.3.6.1.4.1.171.10.75.16.1.2.1INTEGER {manual(1), dynamic(2)}read-writecurrent
ipv4sysIpAddr
OBJECT-TYPE
Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.
1.3.6.1.4.1.171.10.75.16.1.2.2IpAddressread-writecurrent
ipv4sysIpSubnetMask
OBJECT-TYPE
IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.
1.3.6.1.4.1.171.10.75.16.1.2.3IpAddressread-writecurrent
ipv4sysGateway
OBJECT-TYPE
Gateway
1.3.6.1.4.1.171.10.75.16.1.2.4IpAddressread-writecurrent
ipv4dhcpOption12Status
OBJECT-TYPE
Status of DHCP Option12
1.3.6.1.4.1.171.10.75.16.1.2.5INTEGER {enable(1), disable(2)}read-writecurrent
ipv4dhcpOption12HostName
OBJECT-TYPE
Host name in DHCP option 12
1.3.6.1.4.1.171.10.75.16.1.2.6OCTET STRINGread-writecurrent
ipifSupportV4V6Info
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.2.7
sysIpAddrCfgMode
OBJECT-TYPE
Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'sysDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'sysDefaultIpAddr' configured in the system.
1.3.6.1.4.1.171.10.75.16.1.2.7.1INTEGER {manual(1), dynamic(2)}read-writecurrent
sysIpAddr
OBJECT-TYPE
Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored.
1.3.6.1.4.1.171.10.75.16.1.2.7.2IpAddressread-writecurrent
sysIpSubnetMask
OBJECT-TYPE
IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored.
1.3.6.1.4.1.171.10.75.16.1.2.7.3IpAddressread-writecurrent
sysGateway
OBJECT-TYPE
Gateway
1.3.6.1.4.1.171.10.75.16.1.2.7.4IpAddressread-writecurrent
dhcpOption12Status
OBJECT-TYPE
Status of DHCP Option12
1.3.6.1.4.1.171.10.75.16.1.2.7.5INTEGER {enable(1), disable(2)}read-writecurrent
dhcpOption12HostName
OBJECT-TYPE
Host name in DHCP option 12
1.3.6.1.4.1.171.10.75.16.1.2.7.6OCTET STRINGread-writecurrent
ipifName
OBJECT-TYPE
The Description for the interface.
1.3.6.1.4.1.171.10.75.16.1.2.7.7OCTET STRINGread-onlycurrent
ipifVLANname
OBJECT-TYPE
The vlan name for the interface.
1.3.6.1.4.1.171.10.75.16.1.2.7.8OCTET STRINGread-onlycurrent
ipifv6GlobalStatus
OBJECT-TYPE
The ID of VLAN that you want this interface to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.16.1.2.7.9INTEGER {enable(1), disable(2)}read-writecurrent
ipifv6DHCPStatus
OBJECT-TYPE
The state of DHCPv6 that you want this interface to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.16.1.2.7.10INTEGER {enable(1), disable(2)}read-writecurrent
ipifv6AutolinkloStatus
OBJECT-TYPE
The global state of link local that you want this interface to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.16.1.2.7.11INTEGER {enable(1), disable(2)}read-writecurrent
ipifv6NSRetransmitTime
OBJECT-TYPE
The NS's retransmit time that you want this interface to be in. It must be a exist vlan id (1~3600).
1.3.6.1.4.1.171.10.75.16.1.2.7.12INTEGERread-writecurrent
ipifv6DefaultGateway
OBJECT-TYPE
The ipv6 default gateway that you want this interface to be in. It must be a exist vlan id.
1.3.6.1.4.1.171.10.75.16.1.2.7.13Ipv6Addressread-writecurrent
ipifV6AddressTable
OBJECT-TYPE
A list of interface entries.
1.3.6.1.4.1.171.10.75.16.1.2.7.14not-accessiblecurrent
ipifV6AddressEntry
OBJECT-TYPE
An entry containing management information applicable to a particular interface.
1.3.6.1.4.1.171.10.75.16.1.2.7.14.1not-accessiblecurrent
ipifV6AddressMainIndex
OBJECT-TYPE
The index of this IPv6 entry.
1.3.6.1.4.1.171.10.75.16.1.2.7.14.1.1InterfaceIndexread-onlycurrent
ipifV6AddressIpAddr
OBJECT-TYPE
The ip address of this IPv6 entry.
1.3.6.1.4.1.171.10.75.16.1.2.7.14.1.2Ipv6Addressread-onlycurrent
ipifV6AddressIpPrefix
OBJECT-TYPE
The ip prefix of this IPv6 entry.
1.3.6.1.4.1.171.10.75.16.1.2.7.14.1.3INTEGER (1..128)read-onlycurrent
ipifV6AddressIpType
OBJECT-TYPE
The ip type of this IPv6 entry.
1.3.6.1.4.1.171.10.75.16.1.2.7.14.1.4INTEGER {unicast(1), anycast(2), linklocal(3)}read-onlycurrent
ipifV6AddressRowStatus
OBJECT-TYPE
The status of an entry in the Multi Interface Table. Only a subset of the rowstatus variables (active, createAndWait, destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.2.7.14.1.5RowStatusread-createcurrent
ipv4sysIprouteGateway
OBJECT-TYPE
IProute Gateway of the system.
1.3.6.1.4.1.171.10.75.16.1.2.8IpAddressread-writecurrent
ipv4sysIprouteHops
OBJECT-TYPE
IProute Hops of the system.
1.3.6.1.4.1.171.10.75.16.1.2.9INTEGERread-writecurrent
companyTftpGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.3
tftpFwServerIpAddress
OBJECT-TYPE
The TFTP server's IP address is used to upload or download firmware.
1.3.6.1.4.1.171.10.75.16.1.3.1IpAddressread-writeobsolete
tftpFwImageFileName
OBJECT-TYPE
Configure firmware filename to download.
1.3.6.1.4.1.171.10.75.16.1.3.2DisplayString (SIZE(1..64))read-writeobsolete
tftpFwTftpOperation
OBJECT-TYPE
The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName.
1.3.6.1.4.1.171.10.75.16.1.3.3INTEGER {none(0), download(1), upload(2)}read-writeobsolete
tftpFwTftpOperationStatus
OBJECT-TYPE
The tftp operation status represent firmware backup or upgrade status.
1.3.6.1.4.1.171.10.75.16.1.3.4INTEGER {none(0), success(1), fail(2), progressing(3), transmit(4)}read-onlyobsolete
tftpCfgServerIpAddress
OBJECT-TYPE
The TFTP server's IP address is used to upload or download configuration file.
1.3.6.1.4.1.171.10.75.16.1.3.5IpAddressread-writeobsolete
tftpConfigFileName
OBJECT-TYPE
The configuration filename is used to store or retrieve config from the tftp server.
1.3.6.1.4.1.171.10.75.16.1.3.6DisplayString (SIZE(1..64))read-writeobsolete
tftpConfigTftpOperation
OBJECT-TYPE
The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName.
1.3.6.1.4.1.171.10.75.16.1.3.7INTEGER {download(1), upload(2), progressing(3)}read-writeobsolete
tftpConfigTftpOperationStatus
OBJECT-TYPE
The tftp operation status represent configuration file backup or restore status.
1.3.6.1.4.1.171.10.75.16.1.3.8INTEGER {none(0), success(1), fail(2), progressing(3)}read-onlyobsolete
tftpFwTargetGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.3.9
tftpFwTargetServerIpAddress
OBJECT-TYPE
The TFTP server's IP address is used to upload or download firmware.
1.3.6.1.4.1.171.10.75.16.1.3.9.1Ipv6Addressread-writecurrent
tftpFwTargetServerIpType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.16.1.3.9.2INTEGER {iPv4(1), iPv6(2)}read-writecurrent
tftpFwTargetInterfaceName
OBJECT-TYPE
Specifies the interface name when the tftpFwTargetServerIpAddress is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.3.9.3OCTET STRINGread-writecurrent
tftpFwTargetImageFileName
OBJECT-TYPE
Configure firmware filename to download.
1.3.6.1.4.1.171.10.75.16.1.3.9.4DisplayString (SIZE(1..64))read-writecurrent
tftpFwTargetTftpOperation
OBJECT-TYPE
The tftp operates to perform downloading the firmware image to the unit. This object is used in conjunction with configBootTftpServerIp and configBootImageFileName.
1.3.6.1.4.1.171.10.75.16.1.3.9.5INTEGER {none(0), download(1), upload(2)}read-writecurrent
tftpFwTargetTftpOperationStatus
OBJECT-TYPE
The tftp operation status represent firmware backup or upgrade status.
1.3.6.1.4.1.171.10.75.16.1.3.9.6INTEGER {none(0), success(1), fail(2), progressing(3), transmit(4)}read-onlycurrent
tftpCfgTargetGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.3.10
tftpCfgTargetServerIpAddress
OBJECT-TYPE
The TFTP server's IP address is used to upload or download configuration file.
1.3.6.1.4.1.171.10.75.16.1.3.10.1Ipv6Addressread-writecurrent
tftpCfgTargetServerIpType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.16.1.3.10.2INTEGER {iPv4(1), iPv6(2)}read-writecurrent
tftpCfgTargetInterfaceName
OBJECT-TYPE
Specifies the interface name when the tftpCfgTargetServerIpAddress is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.3.10.3OCTET STRINGread-writecurrent
tftpCfgTargetImageFileName
OBJECT-TYPE
The configuration filename is used to store or retrieve config from the tftp server.
1.3.6.1.4.1.171.10.75.16.1.3.10.4DisplayString (SIZE(1..64))read-writecurrent
tftpCfgTargetTftpOperation
OBJECT-TYPE
The tftp operates to perform either downloading the configuration file to the unit or uploading the current configuration file to the tftp server. This object is used in conjunction with configTftpServerIpAddress and configTftpServerFileName.
1.3.6.1.4.1.171.10.75.16.1.3.10.5INTEGER {download(1), upload(2), progressing(3)}read-writecurrent
tftpCfgTargetTftpOperationStatus
OBJECT-TYPE
The tftp operation status represent configuration file backup or restore status.
1.3.6.1.4.1.171.10.75.16.1.3.10.6INTEGER {none(0), success(1), fail(2), progressing(3)}read-onlycurrent
tftpCfgTargetTftpConfigID
OBJECT-TYPE
The tftp config ID determine which config what you need.
1.3.6.1.4.1.171.10.75.16.1.3.10.7INTEGER {configId-1(1), configId-2(2)}read-writecurrent
tftpCfgTargetTftpIncrement
OBJECT-TYPE
The tftp increment determine download config behavior.
1.3.6.1.4.1.171.10.75.16.1.3.10.8INTEGER {false(0), true(1)}read-writecurrent
companyMiscGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.4
miscReset
OBJECT-TYPE
Physically resets the unit - use with care. A (1) resets the unit, a (2) does nothing.
1.3.6.1.4.1.171.10.75.16.1.4.2INTEGER {reset(1), noop(2)}read-writecurrent
miscStatisticsReset
OBJECT-TYPE
Resets the units statistics. A (1) resets the statistics count, a (2) does nothing.
1.3.6.1.4.1.171.10.75.16.1.4.3INTEGER {reset(1), noop(2)}read-writecurrent
companySNMPV3
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.5
snmpGlobalState
OBJECT-TYPE
This object is for enabling or disabling SNMP Community function.
1.3.6.1.4.1.171.10.75.16.1.5.1INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3User
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.5.2
snmpV3UserTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.2.1not-accessiblecurrent
snmpV3UserEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1not-accessiblecurrent
snmpV3UserName
OBJECT-TYPE
A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1.1SnmpAdminString (SIZE(1..32))read-onlycurrent
snmpV3UserVersion
OBJECT-TYPE
A human readable string representing the name of the user. This is the (User-based Security) Model dependent security ID.
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1.2INTEGER {v1(1), v2c(2), v3(3)}read-onlycurrent
snmpV3UserGroupName
OBJECT-TYPE
The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1.3SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3UserAuthProtocol
OBJECT-TYPE
An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be authenticated, and if so, the type of authentication protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of UserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoAuthProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoAuthProtocol, then an 'inconsistentValue' error must be returned. If a set operation tries to set the value to the NoAuthProtocol while the UserPrivProtocol value in the same row is not equal to NoPrivProtocol, then an 'inconsistentValue' error must be returned. That means that an SNMP command generator application must first ensure that the UserPrivProtocol is set to the NoPrivProtocol value before it can set the UserAuthProtocol value to NoAuthProtocol.
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1.4INTEGER {none(1), md5(2), sha(3)}read-createcurrent
snmpV3UserAuthProtocolPassword
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1.5SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3UserPrivProtocol
OBJECT-TYPE
An indication of whether messages sent on behalf of this user to/from the SNMP engine identified by usmUserEngineID, can be protected from disclosure, and if so, the type of privacy protocol which is used. An instance of this object is created concurrently with the creation of any other object instance for the same user (i.e., as part of the processing of the set operation which creates the first object instance in the same conceptual row). If an initial set operation (i.e. at row creation time) tries to set a value for an unknown or unsupported protocol, then a 'wrongValue' error must be returned. The value will be overwritten/set when a set operation is performed on the corresponding instance of usmUserCloneFrom. Once instantiated, the value of such an instance of this object can only be changed via a set operation to the value of the NoPrivProtocol. If a set operation tries to change the value of an existing instance of this object to any value other than NoPrivProtocol, then an 'inconsistentValue' error must be returned. Note that if any privacy protocol is used, then you must also use an authentication protocol. In other words, if usmUserPrivProtocol is set to anything else than NoPrivProtocol, then the corresponding instance of usmUserAuthProtocol cannot have a value of usmNoAuthProtocol. If it does, then an 'inconsistentValue' error must be returned.
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1.6INTEGER {none(1), des(2)}read-createcurrent
snmpV3UserPrivProtocolPassword
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1.7SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3UserStatus
OBJECT-TYPE
The status of this conceptual row. Until instances of all corresponding columns are appropriately configured, the value of the corresponding instance of the usmUserStatus column is 'notReady'. In particular, a newly created row for a user who employs authentication, cannot be made active until the corresponding usmUserCloneFrom and usmUserAuthKeyChange have been set. Further, a newly created row for a user who also employs privacy, cannot be made active until the usmUserPrivKeyChange has been set. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified, except for usmUserOwnAuthKeyChange and usmUserOwnPrivKeyChange. For these 2 objects, the value of usmUserStatus MUST be active.
1.3.6.1.4.1.171.10.75.16.1.5.2.1.1.8RowStatusread-createcurrent
snmpV3Group
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.5.3
snmpV3GroupTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.3.1not-accessiblecurrent
snmpV3GroupEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.3.1.1not-accessiblecurrent
snmpV3GroupName
OBJECT-TYPE
The name of the group to which this entry (e.g., the combination of securityModel and securityName) belongs. This groupName is used as index into the vacmAccessTable to select an access control policy. However, a value in this table does not imply that an instance with the value exists in table vacmAccesTable.
1.3.6.1.4.1.171.10.75.16.1.5.3.1.1.1SnmpAdminString (SIZE(1..32))read-onlycurrent
snmpV3GroupSecurityModel
OBJECT-TYPE
In order to gain the access rights allowed by this conceptual row, this securityModel must be in use.
1.3.6.1.4.1.171.10.75.16.1.5.3.1.1.2INTEGER {v1(1), v2c(2), v3(3)}read-onlycurrent
snmpV3GroupSecurityLevel
OBJECT-TYPE
The minimum level of security required in order to gain the access rights allowed by this conceptual row. A securityLevel of noAuthNoPriv is less than authNoPriv which in turn is less than authPriv. If multiple entries are equally indexed except for this vacmAccessSecurityLevel index, then the entry which has the highest value for vacmAccessSecurityLevel is selected.
1.3.6.1.4.1.171.10.75.16.1.5.3.1.1.3SnmpSecurityLevelread-onlycurrent
snmpV3GroupReadViewName
OBJECT-TYPE
The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes read access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
1.3.6.1.4.1.171.10.75.16.1.5.3.1.1.4SnmpAdminString (SIZE(0..32))read-createcurrent
snmpV3GroupWriteViewName
OBJECT-TYPE
The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes write access. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
1.3.6.1.4.1.171.10.75.16.1.5.3.1.1.5SnmpAdminString (SIZE(0..32))read-createcurrent
snmpV3GroupNotifyViewName
OBJECT-TYPE
The value of an instance of this object identifies the MIB view of the SNMP context to which this conceptual row authorizes access for notifications. The identified MIB view is that one for which the vacmViewTreeFamilyViewName has the same value as the instance of this object; if the value is the empty string or if there is no active MIB view having this value of vacmViewTreeFamilyViewName, then no access is granted.
1.3.6.1.4.1.171.10.75.16.1.5.3.1.1.6SnmpAdminString (SIZE(0..32))read-createcurrent
snmpV3GroupStatus
OBJECT-TYPE
The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.
1.3.6.1.4.1.171.10.75.16.1.5.3.1.1.7RowStatusread-createcurrent
snmpV3ViewTree
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.5.4
snmpV3ViewTreeTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.4.1not-accessiblecurrent
snmpV3ViewTreeEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.4.1.1not-accessiblecurrent
snmpV3viewTreeName
OBJECT-TYPE
The human readable name for a family of view subtrees.
1.3.6.1.4.1.171.10.75.16.1.5.4.1.1.1SnmpAdminString (SIZE(1..32))read-onlycurrent
snmpV3viewTreeSubtree
OBJECT-TYPE
The MIB subtree which when combined with the corresponding instance of vacmViewTreeFamilyMask defines a family of view subtrees.
1.3.6.1.4.1.171.10.75.16.1.5.4.1.1.2OBJECT IDENTIFIERread-onlycurrent
snmpV3viewTreeMask
OBJECT-TYPE
The bit mask which, in combination with the corresponding instance of vacmViewTreeFamilySubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub-identifier of vacmViewTreeFamilySubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-th sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if, for each sub-identifier of the value of vacmViewTreeFamilySubtree, either: the i-th bit of vacmViewTreeFamilyMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of vacmViewTreeFamilySubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of vacmViewTreeFamilySubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of vacmViewTreeFamilySubtree. Note that masks of length greater than zero length do not need to be supported. In this case this object is made read-only.
1.3.6.1.4.1.171.10.75.16.1.5.4.1.1.3OCTET STRING (SIZE(0..16))read-createcurrent
snmpV3viewTreeType
OBJECT-TYPE
Indicates whether the corresponding instances of vacmViewTreeFamilySubtree and vacmViewTreeFamilyMask define a family of view subtrees which is included in or excluded from the MIB view.
1.3.6.1.4.1.171.10.75.16.1.5.4.1.1.4INTEGER {included(1), excluded(2)}read-createcurrent
snmpV3viewTreeStatus
OBJECT-TYPE
The status of this conceptual row. The RowStatus TC [RFC2579] requires that this DESCRIPTION clause states under which circumstances other objects in this row can be modified: The value of this object has no effect on whether other objects in this conceptual row can be modified.
1.3.6.1.4.1.171.10.75.16.1.5.4.1.1.5RowStatusread-createcurrent
snmpV3Community
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.5.5
snmpV3CommunityTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.5.1not-accessiblecurrent
snmpV3CommunityEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.5.1.1not-accessiblecurrent
snmpV3CommunityName
OBJECT-TYPE
The unique index value of a row in this table.
1.3.6.1.4.1.171.10.75.16.1.5.5.1.1.1OCTET STRING (SIZE(1..15))read-onlycurrent
snmpV3CommunityPolicy
OBJECT-TYPE
A human readable string representing the corresponding value of snmpCommunityName in a Security Model independent format.
1.3.6.1.4.1.171.10.75.16.1.5.5.1.1.2SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3CommunityStatus
OBJECT-TYPE
The status of this conceptual row in the snmpCommunityTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The snmpCommunityName and snmpCommunitySecurityName objects must be explicitly set. There is no restriction on setting columns in this table when the value of snmpCommunityStatus is active(1).
1.3.6.1.4.1.171.10.75.16.1.5.5.1.1.3RowStatusread-createcurrent
snmpV3Host
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.5.6
ipv4snmpV3HostTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.6.1not-accessibleobsolete
ipv4snmpV3HostEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.6.1.1not-accessibleobsolete
ipv4snmpV3HostAddress
OBJECT-TYPE
This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.
1.3.6.1.4.1.171.10.75.16.1.5.6.1.1.1IpAddressread-onlyobsolete
ipv4snmpV3HostCommunityName
OBJECT-TYPE
The locally arbitrary.
1.3.6.1.4.1.171.10.75.16.1.5.6.1.1.2SnmpAdminString (SIZE(1..32))read-createobsolete
ipv4snmpV3HostVersion
OBJECT-TYPE
The Level of Security to be used when generating SNMP messages using this entry.
1.3.6.1.4.1.171.10.75.16.1.5.6.1.1.3INTEGER {v1(1), v2c(2), v3NoAuthNoPriv(3), v3AuthNoPriv(4), v3AuthPriv(5)}read-createobsolete
ipv4snmpV3HostStatus
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.6.1.1.4RowStatusread-createobsolete
snmpV3HostTable
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.6.2not-accessiblecurrent
snmpV3HostEntry
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.6.2.1not-accessiblecurrent
snmpV3HostAddress
OBJECT-TYPE
This object contains a transport address. The format of this address depends on the value of the snmpTargetAddrTDomain object. And this object is unique identifier associated with this snmpNotifyEntry.
1.3.6.1.4.1.171.10.75.16.1.5.6.2.1.1Ipv6Addressread-onlycurrent
snmpV3IPType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.16.1.5.6.2.1.2INTEGER {iPv4(1), iPv6(2)}read-onlycurrent
snmpV3HostCommunityName
OBJECT-TYPE
The locally arbitrary.
1.3.6.1.4.1.171.10.75.16.1.5.6.2.1.3SnmpAdminString (SIZE(1..32))read-createcurrent
snmpV3HostVersion
OBJECT-TYPE
The Level of Security to be used when generating SNMP messages using this entry.
1.3.6.1.4.1.171.10.75.16.1.5.6.2.1.4INTEGER {v1(1), v2c(2), v3NoAuthNoPriv(3), v3AuthNoPriv(4), v3AuthPriv(5)}read-createcurrent
snmpV3HostInterfaceName
OBJECT-TYPE
Specifies the interface name when the syslogSrvIP is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.5.6.2.1.5OCTET STRINGread-createcurrent
snmpV3HostStatus
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.6.2.1.6RowStatusread-createcurrent
snmpV3EngineID
OBJECT-TYPE
An SNMP engine's administratively-unique identifier. In a simple agent, this value is always that agent's own snmpEngineID value. The value can also take the value of the snmpEngineID of a remote SNMP engine with which this user can communicate.
1.3.6.1.4.1.171.10.75.16.1.5.7SnmpEngineIDread-writecurrent
snmpV3Trap
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.5.8
snmpV3TrapSNMPAuthentication
OBJECT-TYPE
This object is for enabling or disabling SNMP login fail event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.5.8.1INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapColdStart
OBJECT-TYPE
This object is for enabling or disabling devie Bootup event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.5.8.2INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapWarmStart
OBJECT-TYPE
This object is for enabling or disabling devie Bootup event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.5.8.3INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapLinkUpDown
OBJECT-TYPE
This object is for enabling or disabling Copper link up / link down event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.5.8.4INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapRSTPStateChange
OBJECT-TYPE
This object is for enabling or disabling RSTP topology change event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.5.8.5INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapFirmUpgrade
OBJECT-TYPE
This object is for enabling or disabling Firmware upgrade suess or fail event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.5.8.6INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapBPDUAttack
OBJECT-TYPE
Used to configure trap settings for BPDU attack protection events.
1.3.6.1.4.1.171.10.75.16.1.5.8.11INTEGER {none(1), attackDetected(2), attackCleared(3), both(4)}read-writecurrent
snmpV3TrapPortSecurity
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.8.12INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapIMPBViolation
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.8.13INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapLBD
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.8.14INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapDHCPServerScreening
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.5.8.15INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3TrapDuplicateIPDetected
OBJECT-TYPE
This object is for enabling or disabling send gratuitous trap when IP address conflicted in the network.
1.3.6.1.4.1.171.10.75.16.1.5.8.16INTEGER {enabled(1), disabled(2)}read-writecurrent
snmpV3CommunityEncryption
OBJECT-TYPE
This object is for enabling or disabling community encryption.
1.3.6.1.4.1.171.10.75.16.1.5.9INTEGER {enabled(1), disabled(2)}read-writecurrent
companySTP
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.6
stpBridgeGlobal
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.6.1
stpModuleStatus
OBJECT-TYPE
The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.
1.3.6.1.4.1.171.10.75.16.1.6.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
stpProtocolVersion
OBJECT-TYPE
The version of Spanning Tree Protocol the bridge is currently running. The value 'stpCompatible(0)' indicates the Spanning Tree Protocol specified in IEEE 802.1D and 'rstp(2)' indicates the Rapid Spanning Tree Protocol specified in IEEE 802.1w and 'mstp(3)' indicates the Multiple Spanning Tree Protocol Specified in IEEE 802.1s.
1.3.6.1.4.1.171.10.75.16.1.6.1.2INTEGER {stp(1), rstp(2), mstp(3)}read-writecurrent
stpBridgePriority
OBJECT-TYPE
The Value of the writable portion of the Bridge Identifier comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.
1.3.6.1.4.1.171.10.75.16.1.6.1.3Integer32 (0..61440)read-writecurrent
stpTxHoldCount
OBJECT-TYPE
The value used by the Port Transmit state machine to limit the maximum transmission rate.
1.3.6.1.4.1.171.10.75.16.1.6.1.4Integer32 (1..10)read-writecurrent
stpBridgeMaxAge
OBJECT-TYPE
The value that all bridges use for MaxAge when this bridge is acting as the root. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
1.3.6.1.4.1.171.10.75.16.1.6.1.5Timeout (600..4000)read-writecurrent
stpBridgeHelloTime
OBJECT-TYPE
The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.
1.3.6.1.4.1.171.10.75.16.1.6.1.6Timeout (100..1000)read-writecurrent
stpBridgeForwardDelay
OBJECT-TYPE
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D specifies that the range for this parameter is related to the value of BridgeMaxAge. The granularity of this timer is specified to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
1.3.6.1.4.1.171.10.75.16.1.6.1.7Timeout (400..3000)read-writecurrent
stpFowardBPDU
OBJECT-TYPE
This object is for enabling or disabling forward BPDU.
1.3.6.1.4.1.171.10.75.16.1.6.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
stpRootBridge
OBJECT-TYPE
The bridge identifier of the Root of the common spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the CIST Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
1.3.6.1.4.1.171.10.75.16.1.6.1.9BridgeIdread-onlycurrent
stpRootCost
OBJECT-TYPE
The Cost of the path to the CIST Root as seen from this bridge.
1.3.6.1.4.1.171.10.75.16.1.6.1.10Integer32read-onlycurrent
stpMaxAge
OBJECT-TYPE
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
1.3.6.1.4.1.171.10.75.16.1.6.1.11Timeoutread-onlycurrent
stpForwardDelay
OBJECT-TYPE
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in a particular state before moving to the next state.
1.3.6.1.4.1.171.10.75.16.1.6.1.12Timeoutread-onlycurrent
stpRootPort
OBJECT-TYPE
The Port Number of the Port which offers the lowest path cost from this bridge to the CIST Root Bridge.
1.3.6.1.4.1.171.10.75.16.1.6.1.13Integer32read-onlycurrent
stpTopologyChangeTrapStatus
OBJECT-TYPE
This object is for enabling or disabling topology change event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.6.1.14INTEGER {enabled(1), disabled(2)}read-writecurrent
stpNewRootTrapStatus
OBJECT-TYPE
This object is for enabling or disabling new root event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.6.1.15INTEGER {enabled(1), disabled(2)}read-writecurrent
stpNewRootTraps
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.6.1.16
stpPortTable
OBJECT-TYPE
A table that contains port-specific information for the Spanning Tree Protocol.
1.3.6.1.4.1.171.10.75.16.1.6.2not-accessiblecurrent
stpPortEntry
OBJECT-TYPE
A list of information maintained by every port about the Spanning Tree Protocol state for that port.
1.3.6.1.4.1.171.10.75.16.1.6.2.1not-accessiblecurrent
stpPort
OBJECT-TYPE
The Port number of the port for which this entry contains spanning tree information.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.1INTEGER (1..65535)read-onlycurrent
stpPortStatus
OBJECT-TYPE
Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts
1.3.6.1.4.1.171.10.75.16.1.6.2.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
stpPortPriority
OBJECT-TYPE
The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are set for Port Priority must be in steps of 16.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.3INTEGER (0..240)read-writecurrent
stpAdminPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object stpPortPathCost. If the default Path Cost is being used,this object returns '0' when read.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.4INTEGER (0..200000000)read-writecurrent
stpPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the CIST Root which include this port.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.5INTEGER (1..200000000)read-onlycurrent
stpPortProtocolMigration
OBJECT-TYPE
Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transmit MSTP BPDUs without instance information. Any other operation on this object has no effect and it always returns FALSE(2) when read.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.6INTEGER {false(0), true(1)}read-writecurrent
stpPortEdge
OBJECT-TYPE
This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.7INTEGER {false(0), true(1), auto(2)}read-writecurrent
stpPortAdminP2P
OBJECT-TYPE
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.8INTEGER {forceTrue(0), forceFalse(1), auto(2)}read-writecurrent
stpPortRestrictedRole
OBJECT-TYPE
A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter should be FALSE by default. If set it can cause lack of spanning tree connectivity. It is set by a network administrator to prevent bridges external to a core region of the network influencing the spanning tree active topology, possibly because those bridges are not under the full control of the administrator. This administrator configuration is also known as 'Root Guard'.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.9TruthValueread-writecurrent
stpPortRestrictedTCN
OBJECT-TYPE
A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause temporary loss of connectivity after changes in a spanning trees active topology as a result of persistent incorrectly learnt station location information. It is set by a network administrator to prevent bridges external to a core region of the network causing address flushing in that region, possibly because those bridges are not under the full control of the administrator or MAC_Operational for the attached LANs transitions frequently.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.10TruthValueread-writecurrent
stpPortHelloTime
OBJECT-TYPE
The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.11Timeout (100..1000)read-writecurrent
stpPortState
OBJECT-TYPE
Current state of the Port as defined by the Common spanning tree protocol.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.12INTEGER {disabled(1), discarding(2), learning(4), forwarding(5)}read-onlycurrent
stpPortFowardBPDU
OBJECT-TYPE
This object is for enabling or disabling forward BPDU.
1.3.6.1.4.1.171.10.75.16.1.6.2.1.13INTEGER {enabled(1), disabled(2)}read-writecurrent
mstConfigurationIdentification
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.6.3
mstiConfigurationName
OBJECT-TYPE
The Name for the Region's configuration. By Default Region Name will be equal to the Bridge Mac Address.
1.3.6.1.4.1.171.10.75.16.1.6.3.1OCTET STRING (SIZE(0..32))read-writecurrent
mstiRevisionLevel
OBJECT-TYPE
Version of the MST Region.
1.3.6.1.4.1.171.10.75.16.1.6.3.2Integer32 (0..65535)read-writecurrent
mstCistVlanMapped
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
1.3.6.1.4.1.171.10.75.16.1.6.3.3OCTET STRING (SIZE(0..128))read-onlycurrent
mstCistVlanMapped2k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
1.3.6.1.4.1.171.10.75.16.1.6.3.4OCTET STRING (SIZE(0..128))read-onlycurrent
mstCistVlanMapped3k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
1.3.6.1.4.1.171.10.75.16.1.6.3.5OCTET STRING (SIZE(0..128))read-onlycurrent
mstCistVlanMapped4k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
1.3.6.1.4.1.171.10.75.16.1.6.3.6OCTET STRING (SIZE(0..128))read-onlycurrent
mstVlanMstiMappingTable
OBJECT-TYPE
This table contains one entry for each instance of MSTP. This table maintains context ID as one more index to support Multiple Instances.
1.3.6.1.4.1.171.10.75.16.1.6.3.7not-accessiblecurrent
mstVlanMstiMappingEntry
OBJECT-TYPE
A conceptual row containing the status of the MSTP instance.
1.3.6.1.4.1.171.10.75.16.1.6.3.7.1not-accessiblecurrent
mstInstanceIndex
OBJECT-TYPE
An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance.
1.3.6.1.4.1.171.10.75.16.1.6.3.7.1.1Integer32 (1..15)read-onlycurrent
mstSetVlanList
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values.
1.3.6.1.4.1.171.10.75.16.1.6.3.7.1.2OCTET STRING (SIZE(0..512))read-writecurrent
mstResetVlanList
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to unmap from this Instance. A vlan may not be unmapped from this instance if it is not already mapped to this Instance. This object is used only for SET operation.GET Operation returns null values.
1.3.6.1.4.1.171.10.75.16.1.6.3.7.1.3OCTET STRING (SIZE(0..512))read-writecurrent
mstInstanceVlanMapped
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
1.3.6.1.4.1.171.10.75.16.1.6.3.7.1.4OCTET STRING (SIZE(0..128))read-onlycurrent
mstInstanceVlanMapped2k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
1.3.6.1.4.1.171.10.75.16.1.6.3.7.1.5OCTET STRING (SIZE(0..128))read-onlycurrent
mstInstanceVlanMapped3k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
1.3.6.1.4.1.171.10.75.16.1.6.3.7.1.6OCTET STRING (SIZE(0..128))read-onlycurrent
mstInstanceVlanMapped4k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4095.
1.3.6.1.4.1.171.10.75.16.1.6.3.7.1.7OCTET STRING (SIZE(0..128))read-onlycurrent
stpInstance
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.6.4
mstCistBridgePriority
OBJECT-TYPE
The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.
1.3.6.1.4.1.171.10.75.16.1.6.4.1Integer32 (0..61440)read-writecurrent
mstCistStatus
OBJECT-TYPE
The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.
1.3.6.1.4.1.171.10.75.16.1.6.4.2INTEGER {enabled(1), disabled(2)}read-onlycurrent
mstMstiBridgeTable
OBJECT-TYPE
Table containing Bridge Information specific to Spanning Tree Instance. This table maintains context ID as one more index to support Multiple Instances.
1.3.6.1.4.1.171.10.75.16.1.6.4.3not-accessiblecurrent
mstMstiBridgeEntry
OBJECT-TYPE
Entry indicating the Bridge Information.
1.3.6.1.4.1.171.10.75.16.1.6.4.3.1not-accessiblecurrent
mstMstiInstanceIndex
OBJECT-TYPE
Spanning Tree Instance to which the information belongs.
1.3.6.1.4.1.171.10.75.16.1.6.4.3.1.1Integer32 (1..15)read-onlycurrent
mstMstiBridgePriority
OBJECT-TYPE
The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.
1.3.6.1.4.1.171.10.75.16.1.6.4.3.1.2Integer32 (0..61440)read-writecurrent
mstMstiStatus
OBJECT-TYPE
The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabled in the device on all ports. The object can be set to enabled(1) if and only if, fsMIMstSystemControl set to start.
1.3.6.1.4.1.171.10.75.16.1.6.4.3.1.3INTEGER {enabled(1), disabled(2)}read-onlycurrent
stpInstancePortTable
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.6.5
mstCistPortTable
OBJECT-TYPE
This table contains Common Spanning Tree Port Information.
1.3.6.1.4.1.171.10.75.16.1.6.5.1not-accessiblecurrent
mstCistPortEntry
OBJECT-TYPE
A list of information maintained by every port for Common Spanning tree.
1.3.6.1.4.1.171.10.75.16.1.6.5.1.1not-accessiblecurrent
mstCistPort
OBJECT-TYPE
The Port number of the port for which this entry contains spanning tree information.
1.3.6.1.4.1.171.10.75.16.1.6.5.1.1.1Integer32 (1..65535)not-accessiblecurrent
mstCistPortDesignatedBridge
OBJECT-TYPE
The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.
1.3.6.1.4.1.171.10.75.16.1.6.5.1.1.2BridgeIdread-onlycurrent
mstCistPortAdminPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
1.3.6.1.4.1.171.10.75.16.1.6.5.1.1.3Integer32 (0..200000000)read-writecurrent
mstCistPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
1.3.6.1.4.1.171.10.75.16.1.6.5.1.1.4Integer32 (1..200000000)read-writecurrent
mstCistPortPriority
OBJECT-TYPE
The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.
1.3.6.1.4.1.171.10.75.16.1.6.5.1.1.5Integer32 (0..240)read-writecurrent
mstCistForcePortState
OBJECT-TYPE
Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port
1.3.6.1.4.1.171.10.75.16.1.6.5.1.1.6INTEGER {disabled(0), enabled(1)}read-onlycurrent
mstCistCurrentPortRole
OBJECT-TYPE
Current Port Role of the port for this spanning tree instance.
1.3.6.1.4.1.171.10.75.16.1.6.5.1.1.7INTEGER {disabled(0), alternate(1), backup(2), root(3), designated(4), master(5)}read-onlycurrent
mstMstiPortTable
OBJECT-TYPE
This table contains Spanning Tree Instance Specific Port Information.
1.3.6.1.4.1.171.10.75.16.1.6.5.2not-accessiblecurrent
mstMstiPortEntry
OBJECT-TYPE
A list of information maintained by every port for each and every spanning tree instance.
1.3.6.1.4.1.171.10.75.16.1.6.5.2.1not-accessiblecurrent
mstMstiPort
OBJECT-TYPE
The Port number of the port for which this entry contains spanning tree information.
1.3.6.1.4.1.171.10.75.16.1.6.5.2.1.1Integer32 (1..65535)not-accessiblecurrent
mstMstiPortDesignatedBridge
OBJECT-TYPE
The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.
1.3.6.1.4.1.171.10.75.16.1.6.5.2.1.2BridgeIdread-onlycurrent
mstMstiPortAdminPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
1.3.6.1.4.1.171.10.75.16.1.6.5.2.1.3Integer32 (0..200000000)read-writecurrent
mstMstiPortPathCost
OBJECT-TYPE
The contribution of this port to the path cost of paths towards the MSTI Root which include this port.
1.3.6.1.4.1.171.10.75.16.1.6.5.2.1.4Integer32 (1..200000000)read-writecurrent
mstMstiPortPriority
OBJECT-TYPE
The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priority must be in steps of 16.
1.3.6.1.4.1.171.10.75.16.1.6.5.2.1.5Integer32 (0..240)read-writecurrent
mstMstiForcePortState
OBJECT-TYPE
Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' for this port
1.3.6.1.4.1.171.10.75.16.1.6.5.2.1.6INTEGER {disabled(0), enabled(1)}read-onlycurrent
mstMstiCurrentPortRole
OBJECT-TYPE
Current Port Role of the port for this spanning tree instance.
1.3.6.1.4.1.171.10.75.16.1.6.5.2.1.7INTEGER {disabled(0), alternate(1), backup(2), root(3), designated(4), master(5)}read-onlycurrent
companyDot1qVlanGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.7
dot1qVlanManagementOnOff
OBJECT-TYPE
Enable/Disable management VLAN mechanism.
1.3.6.1.4.1.171.10.75.16.1.7.2INTEGER {enabled(1), disabled(2)}read-writecurrent
dot1qVlanManagementid
OBJECT-TYPE
The management VLAN ID, which will allow to forward packets of that VLAN to CPU.
1.3.6.1.4.1.171.10.75.16.1.7.3INTEGERread-writecurrent
dot1qVlanAsyOnOff
OBJECT-TYPE
Enable/Disable IEEE 802.1Q Asymmetric VLAN
1.3.6.1.4.1.171.10.75.16.1.7.5INTEGER {enabled(1), disabled(2)}read-writecurrent
dot1qVlanTable
OBJECT-TYPE
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
1.3.6.1.4.1.171.10.75.16.1.7.6not-accessiblecurrent
dot1qVlanEntry
OBJECT-TYPE
Information for a VLAN configured into the device by (local or network) management.
1.3.6.1.4.1.171.10.75.16.1.7.6.1not-accessiblecurrent
dot1qVlanName
OBJECT-TYPE
An administratively assigned string, which may be used to identify the VLAN.
1.3.6.1.4.1.171.10.75.16.1.7.6.1.1SnmpAdminString (SIZE(0..20))read-createcurrent
dot1qVlanEgressPorts
OBJECT-TYPE
The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros of appropriate length, indicating not fixed.
1.3.6.1.4.1.171.10.75.16.1.7.6.1.2PortListread-createcurrent
dot1qVlanForbiddenPorts
OBJECT-TYPE
The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar control for Registration Forbidden for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanEgressPorts. The default value of this object is a string of zeros of appropriate length, excluding all ports from the forbidden set.
1.3.6.1.4.1.171.10.75.16.1.7.6.1.3PortListread-writecurrent
dot1qVlanUntaggedPorts
OBJECT-TYPE
The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There is no specified default for other VLANs. If a device agent cannot support the set of ports being set then it will reject the set operation with an error. An example might be if a manager attempts to set more than one VLAN to be untagged on egress where the device does not support this IEEE 802.1Q option.
1.3.6.1.4.1.171.10.75.16.1.7.6.1.4PortListread-createcurrent
dot1qVlanAdvertisementStatus
OBJECT-TYPE
Enable/Disable Advertisement Status of the IEEE 802.1Q VLAN.
1.3.6.1.4.1.171.10.75.16.1.7.6.1.5INTEGER {enabled(1), disabled(2)}read-createcurrent
dot1qVlanRowStatus
OBJECT-TYPE
The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.
1.3.6.1.4.1.171.10.75.16.1.7.6.1.6RowStatusread-createcurrent
dot1qVlanPVIDAutoAssignOnOff
OBJECT-TYPE
Enable/Disable VLAN PVID auto assignment
1.3.6.1.4.1.171.10.75.16.1.7.9INTEGER {enabled(1), disabled(2)}read-writecurrent
companyLA
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.8
laSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.8.1
laStatus
OBJECT-TYPE
Sets the Link Aggregation Module administrative status as enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.8.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
laPortChannelTable
OBJECT-TYPE
A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel.
1.3.6.1.4.1.171.10.75.16.1.8.1.3not-accessiblecurrent
laPortChannelEntry
OBJECT-TYPE
There is one entry in this table for each created port-channel port.
1.3.6.1.4.1.171.10.75.16.1.8.1.3.1not-accessiblecurrent
laPortChannelIfIndex
OBJECT-TYPE
The index of the port-channel(Aggregator's interface index).
1.3.6.1.4.1.171.10.75.16.1.8.1.3.1.1InterfaceIndexread-onlycurrent
laPortChannelMemberList
OBJECT-TYPE
Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.
1.3.6.1.4.1.171.10.75.16.1.8.1.3.1.2PortListread-writecurrent
laPortChannelMode
OBJECT-TYPE
Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.
1.3.6.1.4.1.171.10.75.16.1.8.1.3.1.3PortLaModeread-writecurrent
laPortChannelMasterPort
OBJECT-TYPE
The master port of the port-channel.
1.3.6.1.4.1.171.10.75.16.1.8.1.3.1.4InterfaceIndexread-writecurrent
laAlgorithm
OBJECT-TYPE
Sets the Link Aggregation load balance algorithm.
1.3.6.1.4.1.171.10.75.16.1.8.1.4INTEGER {sourceMAC(1), destMAC(2), sourceAndDestMAC(3), sourceIP(4), destIP(5), sourceAndDestIP(6)}read-writecurrent
laPortControl
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.8.2
laPortControlTable
OBJECT-TYPE
A table that contains Link Aggregation Control configuration information about every Aggregation Port associated with this device. A row appears in this table for each physical port.
1.3.6.1.4.1.171.10.75.16.1.8.2.1not-accessiblecurrent
laPortControlEntry
OBJECT-TYPE
A list of Link Aggregation Control configuration parameters for each Aggregation Port on this device.
1.3.6.1.4.1.171.10.75.16.1.8.2.1.1not-accessiblecurrent
laPortControlIndex
OBJECT-TYPE
The index of the port.
1.3.6.1.4.1.171.10.75.16.1.8.2.1.1.1InterfaceIndexread-onlycurrent
laPortActorPortPriority
OBJECT-TYPE
The priority value assigned to this Aggregation Port. This 16-bit value is read-write.
1.3.6.1.4.1.171.10.75.16.1.8.2.1.1.2INTEGER (0..65535)read-writecurrent
laPortActorActivity
OBJECT-TYPE
This object indicates LACP_Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and partner are both in passive mode, they do not exchange LACP packets.
1.3.6.1.4.1.171.10.75.16.1.8.2.1.1.3INTEGER {active(1), passive(2)}read-writecurrent
laPortActorTimeout
OBJECT-TYPE
This object indicates LACP_Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds.
1.3.6.1.4.1.171.10.75.16.1.8.2.1.1.4INTEGER {short(1), long(2)}read-writecurrent
companyStaticMAC
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.9
staticDisableAutoLearn
OBJECT-TYPE
Set on to disable Auto Learning Excluding Uplink Port and set off to enable Auto Learning.
1.3.6.1.4.1.171.10.75.16.1.9.1INTEGER {on(1), off(2)}read-writecurrent
staticAutoLearningList
OBJECT-TYPE
The set of the device's member ports that belong to the Static MAC auto learning enable/disable. For example, when Disable Auto Learning is enable, the octet value set up as '# 0x0F 0xFF 0xFF 0xFF' means from port 1 to port 4 are not in auto learning state, the other ports are in auto learning state. It can be set up when Disable Auto Learning is enable.
1.3.6.1.4.1.171.10.75.16.1.9.2PortListread-writecurrent
staticTable
OBJECT-TYPE
A list of the Static MACs
1.3.6.1.4.1.171.10.75.16.1.9.3not-accessiblecurrent
staticEntry
OBJECT-TYPE
A Static MAC entry containing the mac and forwarding port.
1.3.6.1.4.1.171.10.75.16.1.9.3.1not-accessiblecurrent
staticVlanID
OBJECT-TYPE
The VLAN ID of the static MAC entry.
1.3.6.1.4.1.171.10.75.16.1.9.3.1.1INTEGER (1..4094)read-onlycurrent
staticMac
OBJECT-TYPE
The MAC address associated of the static MAC entry.
1.3.6.1.4.1.171.10.75.16.1.9.3.1.2MacAddressread-onlycurrent
staticPort
OBJECT-TYPE
The forwarding port of the static MAC entry. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.9.3.1.3INTEGER (1..26)read-onlycurrent
staticStatus
OBJECT-TYPE
The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.
1.3.6.1.4.1.171.10.75.16.1.9.3.1.4RowStatusread-writecurrent
autoFdbTable
OBJECT-TYPE
A list of the Auto Fdb
1.3.6.1.4.1.171.10.75.16.1.9.4not-accessiblecurrent
autoFdbEntry
OBJECT-TYPE
A auto fdb entry containing the ipaddress
1.3.6.1.4.1.171.10.75.16.1.9.4.1not-accessiblecurrent
autoFdbIPAddress
OBJECT-TYPE
The IpAddress of the autoFdbEntry.
1.3.6.1.4.1.171.10.75.16.1.9.4.1.1IpAddressread-onlycurrent
autoFdbVlanID
OBJECT-TYPE
The VlanID of the autoFdbEntry.
1.3.6.1.4.1.171.10.75.16.1.9.4.1.2Integer32read-onlycurrent
autoFdbMacAddress
OBJECT-TYPE
The Mac Address of the autoFdbEntry.
1.3.6.1.4.1.171.10.75.16.1.9.4.1.3MacAddressread-onlycurrent
autoFdbPort
OBJECT-TYPE
The Port of the autoFdbEntry.
1.3.6.1.4.1.171.10.75.16.1.9.4.1.4INTEGERread-onlycurrent
autoFdbTimeStamp
OBJECT-TYPE
The Time Stamp of the autoFdbEntry.
1.3.6.1.4.1.171.10.75.16.1.9.4.1.5Integer32read-onlycurrent
autoFdbStatus
OBJECT-TYPE
The status of an entry in the Auto Fdb Table. Only a subset of the rowstatus variables (createAndGo, createAndWait,destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.9.4.1.6RowStatusread-writecurrent
staticVlanBaseTable
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.9.5
staticVlanBaseAutoLearnList1k
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this Auto Learn, the bit corresponding to that VLAN is set to '1'. Write AutoLearnList1k use 256 character, and conform to the foregoing rules.
1.3.6.1.4.1.171.10.75.16.1.9.5.1OCTET STRING (SIZE(0..128))read-writecurrent
staticVlanBaseAutoLearnList2k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1025 through 2048. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this Auto Learn. Write AutoLearnList2k use 256 character, and conform to the foregoing rules.
1.3.6.1.4.1.171.10.75.16.1.9.5.2OCTET STRING (SIZE(0..128))read-writecurrent
staticVlanBaseAutoLearnList3k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2049 through 3072. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this Auto Learn the bit corresponding to that VLAN is set to '1'. Write AutoLearnList3k use 256 character, and conform to the foregoing rules.
1.3.6.1.4.1.171.10.75.16.1.9.5.3OCTET STRING (SIZE(0..128))read-writecurrent
staticVlanBaseAutoLearnList4k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3073 through 4094. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this Auto Learn the bit corresponding to that VLAN is set to '1'. Write AutoLearnList4k use 256 character, and conform to the foregoing rules.
1.3.6.1.4.1.171.10.75.16.1.9.5.4OCTET STRING (SIZE(0..128))read-writecurrent
staticVlanBaseEnableAutoLearn
OBJECT-TYPE
Set enable vlan list to auto learn, and range 1-4094.
1.3.6.1.4.1.171.10.75.16.1.9.5.5OCTET STRING (SIZE(0..512))read-writecurrent
staticVlanBaseDisableAutoLearn
OBJECT-TYPE
Set disable vlan list to auto learn, and range 1-4094.
1.3.6.1.4.1.171.10.75.16.1.9.5.6OCTET STRING (SIZE(0..512))read-writecurrent
companyIgsGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.10
igsSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.10.1
igsStatus
OBJECT-TYPE
Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module starts protocol operations. When set to 'disabled', the IGS module stops performing protocol operations.
1.3.6.1.4.1.171.10.75.16.1.10.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
igsRouterPortPurgeInterval
OBJECT-TYPE
This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.
1.3.6.1.4.1.171.10.75.16.1.10.1.2Integer32 (60..600)read-writecurrent
igsHostPortPurgeInterval
OBJECT-TYPE
This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.
1.3.6.1.4.1.171.10.75.16.1.10.1.3Integer32 (130..153025)read-writecurrent
igsDataDrivenLearningMaxLearnedEntryVlaue
OBJECT-TYPE
The maximum data driven learning entry value.
1.3.6.1.4.1.171.10.75.16.1.10.1.8INTEGER (1..1024)read-writecurrent
igsReportToAllPort
OBJECT-TYPE
Enables or disables IGMP snooping in the system. When set to 'enabled', the IGS module forwards packets to report to all port. When set to 'disabled', the IGS module forwards packets to router port only.
1.3.6.1.4.1.171.10.75.16.1.10.1.9INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.10.3
igsVlanRouterTable
OBJECT-TYPE
This table contains the list of ports through which a router, in a particular VLAN is reachable.
1.3.6.1.4.1.171.10.75.16.1.10.3.3not-accessiblecurrent
igsVlanRouterEntry
OBJECT-TYPE
Contains the VLAN ID and list of ports on which routers are present in the VLAN.
1.3.6.1.4.1.171.10.75.16.1.10.3.3.1not-accessiblecurrent
igsVlanRouterVlanId
OBJECT-TYPE
VLAN ID of the ports through which router is reachable.
1.3.6.1.4.1.171.10.75.16.1.10.3.3.1.1Integer32 (1..4094)read-onlycurrent
igsVlanRouterPortList
OBJECT-TYPE
List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.
1.3.6.1.4.1.171.10.75.16.1.10.3.3.1.2PortListread-onlycurrent
igsVlanFilterTable
OBJECT-TYPE
This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.
1.3.6.1.4.1.171.10.75.16.1.10.3.4not-accessiblecurrent
igsVlanFilterEntry
OBJECT-TYPE
Contains snooping status , version and fast leave configuration for a specific VLAN.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1not-accessiblecurrent
igsVlanFilterVlanId
OBJECT-TYPE
Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.1Integer32 (1..4094)read-onlycurrent
igsVlanSnoopStatus
OBJECT-TYPE
This object allows you to enable/disable IGS function on a specific VLAN.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanQuerier
OBJECT-TYPE
Indicates whether the switch is configured as a querier in the VLAN
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.3INTEGER {enabled(1), disabled(2)}read-onlycurrent
igsVlanCfgQuerier
OBJECT-TYPE
The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanQueryInterval
OBJECT-TYPE
This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.5Integer32 (60..600)read-writecurrent
igsVlanRtrPortList
OBJECT-TYPE
List of ports which are configured statically as router ports
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.6PortListread-writecurrent
igsVlanFbdRtrPortList
OBJECT-TYPE
List of ports which can be configured statically as forbidden router ports.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.7PortListread-writecurrent
igsVlanFastLeave
OBJECT-TYPE
Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanDataDrivenLearningStatus
OBJECT-TYPE
This object allows you to enable/disable Data Driven Learning function on a specific VLAN.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.9INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanQuerierVersionStatus
OBJECT-TYPE
This object allows you to enable/disable Querier Version function on a specific VLAN.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.10INTEGER {igmp-v2(2), igmp-v3(3)}read-writecurrent
igsVlanDataDrivenLearningAgeOutStatus
OBJECT-TYPE
This object allows you to enable/disable Data Driven Learning Age Out State on a specific VLAN.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.11INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanReportSuppression
OBJECT-TYPE
Enables or disables Report suppression in the system.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.12INTEGER {enabled(1), disabled(2)}read-writecurrent
igsVlanRobustnessValue
OBJECT-TYPE
When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'igsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.13Integer32 (2..255)read-writecurrent
igsVlanGrpQueryInterval
OBJECT-TYPE
The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'igsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.14Integer32 (1..25)read-writecurrent
igsVlanQueryMaxResponseTime
OBJECT-TYPE
The maximum query response time advertised in IGMPv2 general queries on this interface.
1.3.6.1.4.1.171.10.75.16.1.10.3.4.1.15INTEGER (10..25)read-writecurrent
igsVlanMulticastGroupTable
OBJECT-TYPE
This table contains MAC based multicast forwarding information.
1.3.6.1.4.1.171.10.75.16.1.10.3.5not-accessiblecurrent
igsVlanMulticastGroupEntry
OBJECT-TYPE
This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.
1.3.6.1.4.1.171.10.75.16.1.10.3.5.1not-accessiblecurrent
igsVlanMulticastGroupVlanId
OBJECT-TYPE
VLAN ID pertaining to the Multicast forwarding entry
1.3.6.1.4.1.171.10.75.16.1.10.3.5.1.1Integer32 (1..4094)read-onlycurrent
igsVlanMulticastGroupIpAddress
OBJECT-TYPE
Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.
1.3.6.1.4.1.171.10.75.16.1.10.3.5.1.2InetAddressread-onlycurrent
igsVlanMulticastGroupMacAddress
OBJECT-TYPE
Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.
1.3.6.1.4.1.171.10.75.16.1.10.3.5.1.3MacAddressread-onlycurrent
igsVlanMulticastGroupPortList
OBJECT-TYPE
List of ports onto which the multicast data packets destined for this group will be forwarded.
1.3.6.1.4.1.171.10.75.16.1.10.3.5.1.4PortListread-onlycurrent
igsHost
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.10.6
igsHostTable
OBJECT-TYPE
This table is used to manage the IGMP Host based Fast Leave function of the switch.
1.3.6.1.4.1.171.10.75.16.1.10.6.1not-accessiblecurrent
igsHostEntry
OBJECT-TYPE
Contains management entities for IGMP Host based fast leave function.
1.3.6.1.4.1.171.10.75.16.1.10.6.1.1not-accessiblecurrent
igsHostTableVLANID
OBJECT-TYPE
VLAN ID of Host table entry.
1.3.6.1.4.1.171.10.75.16.1.10.6.1.1.1Integer32 (1..4094)read-onlycurrent
igsHostTableGroupAddress
OBJECT-TYPE
Group address of Host table entry.
1.3.6.1.4.1.171.10.75.16.1.10.6.1.1.2InetAddressread-onlycurrent
igsHostTablePort
OBJECT-TYPE
Port number of Host table entry. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.10.6.1.1.3Integer32 (1..26)read-onlycurrent
igsHostTableHostIPAddress
OBJECT-TYPE
Host IP address of Group in Host table entry.
1.3.6.1.4.1.171.10.75.16.1.10.6.1.1.4InetAddressread-onlycurrent
companyGVRPGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.11
gvrpGVRPGlobalSettingsOnOff
OBJECT-TYPE
Enable/Disable GVRP mechanism.
1.3.6.1.4.1.171.10.75.16.1.11.1INTEGER {enabled(1), disabled(2)}read-writecurrent
gvrpSettingsJoinTime
OBJECT-TYPE
The Join Time value assigned to this Join Time field. This 16-bit value is read-write.
1.3.6.1.4.1.171.10.75.16.1.11.2INTEGER (100..100000)read-writecurrent
gvrpSettingsLeaveTime
OBJECT-TYPE
The Leave Time value assigned to this Leave Time field. This 16-bit value is read-write.
1.3.6.1.4.1.171.10.75.16.1.11.3INTEGER (100..100000)read-writecurrent
gvrpSettingsLeaveAllTime
OBJECT-TYPE
The Leave_All Time value assigned to this Leave_All Time field. This 16-bit value is read-write.
1.3.6.1.4.1.171.10.75.16.1.11.4INTEGER (100..100000)read-writecurrent
gvrpSettingsTable
OBJECT-TYPE
A table containing static configuration information for each GVRP configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
1.3.6.1.4.1.171.10.75.16.1.11.5not-accessiblecurrent
gvrpSettingsEntry
OBJECT-TYPE
Information for a GVRP configured into the device by (local or network) management.
1.3.6.1.4.1.171.10.75.16.1.11.5.1not-accessiblecurrent
gvrpSettingsPortControlIndex
OBJECT-TYPE
The index of the port.
1.3.6.1.4.1.171.10.75.16.1.11.5.1.1InterfaceIndexread-onlycurrent
gvrpSettingsPVID
OBJECT-TYPE
The PVID value assigned to this Aggregation Port. This 16-bit value is read-write.
1.3.6.1.4.1.171.10.75.16.1.11.5.1.2INTEGER (1..4094)read-writecurrent
gvrpSettingsGVRPState
OBJECT-TYPE
Enable/Disable GVRP State to this Aggregation Port.
1.3.6.1.4.1.171.10.75.16.1.11.5.1.3INTEGER {enabled(1), disabled(2)}read-writecurrent
gvrpSettingsIngressChecking
OBJECT-TYPE
Enable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port.
1.3.6.1.4.1.171.10.75.16.1.11.5.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
gvrpSettingsAcceptableFrameType
OBJECT-TYPE
Chose types All Frames/Tagged to this Aggregation Port.
1.3.6.1.4.1.171.10.75.16.1.11.5.1.5INTEGER {allFrames(1), taggedOnly(2)}read-writecurrent
companyQoSGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12
cosScheduleMechanism
OBJECT-TYPE
Queuing mechanism. strictPriority(1) : Strict Priority wrr(2) : Weighted Round Robin Strict-priority scheduling is implemented with a special strict-priority scheduler node that is stacked directly above the port. Queues stacked on top of the strict-priority scheduler node always get bandwidth before other queues. Weighted round-robin scheduling is designed to better handle queues with different processing capacities. Each queue has a weight : Low is 1, Medium is 2, High is 4 and Highest is 8 for WS3 spec. Queues with higher weights get bandwidth before than other queues with less weights.
1.3.6.1.4.1.171.10.75.16.1.12.1INTEGER {strictPriority(1), wrr(2), strict3wrr(3), strict2wrr(4)}read-writecurrent
cosOutputSchedule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.2
cosClassTable
OBJECT-TYPE
A list of cosOutputSchedule.
1.3.6.1.4.1.171.10.75.16.1.12.2.1not-accessiblecurrent
cosClassEntry
OBJECT-TYPE
A list of cosOutputClass Weight.
1.3.6.1.4.1.171.10.75.16.1.12.2.1.1not-accessiblecurrent
cosClassIndex
OBJECT-TYPE
A index of class 0 ~ 3.
1.3.6.1.4.1.171.10.75.16.1.12.2.1.1.1INTEGER (0..3)read-onlycurrent
cosWeight
OBJECT-TYPE
cos weight
1.3.6.1.4.1.171.10.75.16.1.12.2.1.1.2INTEGER (1..55)read-writecurrent
qosDefaultUserPri
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.4
qosDefaultUserPriTable
OBJECT-TYPE
A list of 802.1p port default priority Entries.
1.3.6.1.4.1.171.10.75.16.1.12.4.1not-accessiblecurrent
qosDefaultUserPriEntry
OBJECT-TYPE
A list of 802.1p port default priority priorities.
1.3.6.1.4.1.171.10.75.16.1.12.4.1.1not-accessiblecurrent
qosDefaultUserPriPortIndex
OBJECT-TYPE
A port identifier that is in the range of 1 to ifNumber.
1.3.6.1.4.1.171.10.75.16.1.12.4.1.1.1INTEGER (1..26)read-onlycurrent
qosDefaultPriority
OBJECT-TYPE
For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled.
1.3.6.1.4.1.171.10.75.16.1.12.4.1.1.2INTEGER {priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7)}read-writecurrent
qosEffectiveDefaultPriority
OBJECT-TYPE
For ingress untagged packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled.
1.3.6.1.4.1.171.10.75.16.1.12.4.1.1.3INTEGER {priority0(0), priority1(1), priority2(2), priority3(3), priority4(4), priority5(5), priority6(6), priority7(7)}read-onlycurrent
qosUserPriority
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.5
qosUserPriorityTable
OBJECT-TYPE
A table mapping evaluated User Priority to Traffic Class, for forwarding by the bridge. Traffic class is a number in the range (0..3).
1.3.6.1.4.1.171.10.75.16.1.12.5.1not-accessiblecurrent
qosUserPriEntry
OBJECT-TYPE
User Priority to Traffic Class mapping.
1.3.6.1.4.1.171.10.75.16.1.12.5.1.1not-accessiblecurrent
qosUserPriIndex
OBJECT-TYPE
For ingress tagged packets, D-Link Smart Switches will refer to these information and prioritize them with 4 different priority queues. If 802.1p is enabled.
1.3.6.1.4.1.171.10.75.16.1.12.5.1.1.1INTEGER (0..7)read-onlycurrent
qosUserPriClass
OBJECT-TYPE
The User Class the received frame is mapped to.
1.3.6.1.4.1.171.10.75.16.1.12.5.1.1.2INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServTOS
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.6
qosDSCPTOSMode
OBJECT-TYPE
Settings of Qos mode: DSCP QoS or TOS Qos. IEEE 802.1p : It specifies a priority(0~7) value to four queues in WS3 : Low(1,2), Medium(0,3), High(4,5) and Highest(6,7), inclusive that can be used by Quality of Service (QoS) disciplines to differentiate traffic. DSCP : Differentiated services enhancements to the Internet protocol are intended to enable scalable service discrimination in the Internet without the need for per-flow state and signaling at every hop.
1.3.6.1.4.1.171.10.75.16.1.12.6.1INTEGER {tos(1), dscp(2)}read-writecurrent
qosDiffServTypeGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.6.2
qosDiffServType00
OBJECT-TYPE
DiffServ Type 0 : IP ToS value = 0
1.3.6.1.4.1.171.10.75.16.1.12.6.2.1INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType01
OBJECT-TYPE
DiffServ Type 01 : IP ToS value = 4
1.3.6.1.4.1.171.10.75.16.1.12.6.2.2INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType02
OBJECT-TYPE
DiffServ Type 02 : IP ToS value = 8
1.3.6.1.4.1.171.10.75.16.1.12.6.2.3INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType03
OBJECT-TYPE
DiffServ Type 03 : IP ToS value = 12
1.3.6.1.4.1.171.10.75.16.1.12.6.2.4INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType04
OBJECT-TYPE
DiffServ Type 04 : IP ToS value = 16
1.3.6.1.4.1.171.10.75.16.1.12.6.2.5INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType05
OBJECT-TYPE
DiffServ Type 05 : IP ToS value = 20
1.3.6.1.4.1.171.10.75.16.1.12.6.2.6INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType06
OBJECT-TYPE
DiffServ Type 06 : IP ToS value = 24
1.3.6.1.4.1.171.10.75.16.1.12.6.2.7INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType07
OBJECT-TYPE
DiffServ Type 07 : IP ToS value = 28
1.3.6.1.4.1.171.10.75.16.1.12.6.2.8INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType08
OBJECT-TYPE
DiffServ Type 08 : IP ToS value = 32
1.3.6.1.4.1.171.10.75.16.1.12.6.2.9INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType09
OBJECT-TYPE
DiffServ Type 09 : IP ToS value = 36
1.3.6.1.4.1.171.10.75.16.1.12.6.2.10INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType10
OBJECT-TYPE
DiffServ Type 10 : IP ToS value = 40
1.3.6.1.4.1.171.10.75.16.1.12.6.2.11INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType11
OBJECT-TYPE
DiffServ Type 11 : IP ToS value = 44
1.3.6.1.4.1.171.10.75.16.1.12.6.2.12INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType12
OBJECT-TYPE
DiffServ Type 12 : IP ToS value = 48
1.3.6.1.4.1.171.10.75.16.1.12.6.2.13INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType13
OBJECT-TYPE
DiffServ Type 13 : IP ToS value = 52
1.3.6.1.4.1.171.10.75.16.1.12.6.2.14INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType14
OBJECT-TYPE
DiffServ Type 14 : IP ToS value = 56
1.3.6.1.4.1.171.10.75.16.1.12.6.2.15INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType15
OBJECT-TYPE
DiffServ Type 15 : IP ToS value = 60
1.3.6.1.4.1.171.10.75.16.1.12.6.2.16INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType16
OBJECT-TYPE
DiffServ Type 16 : IP ToS value = 64
1.3.6.1.4.1.171.10.75.16.1.12.6.2.17INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType17
OBJECT-TYPE
DiffServ Type 17 : IP ToS value = 68
1.3.6.1.4.1.171.10.75.16.1.12.6.2.18INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType18
OBJECT-TYPE
DiffServ Type 18 : IP ToS value = 72
1.3.6.1.4.1.171.10.75.16.1.12.6.2.19INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType19
OBJECT-TYPE
DiffServ Type 19 : IP ToS value = 76
1.3.6.1.4.1.171.10.75.16.1.12.6.2.20INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType20
OBJECT-TYPE
DiffServ Type 20 : IP ToS value = 80
1.3.6.1.4.1.171.10.75.16.1.12.6.2.21INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType21
OBJECT-TYPE
DiffServ Type 21 : IP ToS value = 84
1.3.6.1.4.1.171.10.75.16.1.12.6.2.22INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType22
OBJECT-TYPE
DiffServ Type 22 : IP ToS value = 88
1.3.6.1.4.1.171.10.75.16.1.12.6.2.23INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType23
OBJECT-TYPE
DiffServ Type 23 : IP ToS value = 92
1.3.6.1.4.1.171.10.75.16.1.12.6.2.24INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType24
OBJECT-TYPE
DiffServ Type 24 : IP ToS value = 96
1.3.6.1.4.1.171.10.75.16.1.12.6.2.25INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType25
OBJECT-TYPE
DiffServ Type 25 : IP ToS value = 100
1.3.6.1.4.1.171.10.75.16.1.12.6.2.26INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType26
OBJECT-TYPE
DiffServ Type 26 : IP ToS value = 104
1.3.6.1.4.1.171.10.75.16.1.12.6.2.27INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType27
OBJECT-TYPE
DiffServ Type 27 : IP ToS value = 108
1.3.6.1.4.1.171.10.75.16.1.12.6.2.28INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType28
OBJECT-TYPE
DiffServ Type 28 : IP ToS value = 112
1.3.6.1.4.1.171.10.75.16.1.12.6.2.29INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType29
OBJECT-TYPE
DiffServ Type 29 : IP ToS value = 116
1.3.6.1.4.1.171.10.75.16.1.12.6.2.30INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType30
OBJECT-TYPE
DiffServ Type 30 : IP ToS value = 120
1.3.6.1.4.1.171.10.75.16.1.12.6.2.31INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType31
OBJECT-TYPE
DiffServ Type 31 : IP ToS value = 124
1.3.6.1.4.1.171.10.75.16.1.12.6.2.32INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType32
OBJECT-TYPE
DiffServ Type 32 : IP ToS value = 128
1.3.6.1.4.1.171.10.75.16.1.12.6.2.33INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType33
OBJECT-TYPE
DiffServ Type 33 : IP ToS value = 132
1.3.6.1.4.1.171.10.75.16.1.12.6.2.34INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType34
OBJECT-TYPE
DiffServ Type 34 : IP ToS value = 136
1.3.6.1.4.1.171.10.75.16.1.12.6.2.35INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType35
OBJECT-TYPE
DiffServ Type 35 : IP ToS value = 140
1.3.6.1.4.1.171.10.75.16.1.12.6.2.36INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType36
OBJECT-TYPE
DiffServ Type 36 : IP ToS value = 144
1.3.6.1.4.1.171.10.75.16.1.12.6.2.37INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType37
OBJECT-TYPE
DiffServ Type 37 : IP ToS value = 148
1.3.6.1.4.1.171.10.75.16.1.12.6.2.38INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType38
OBJECT-TYPE
DiffServ Type 38 : IP ToS value = 152
1.3.6.1.4.1.171.10.75.16.1.12.6.2.39INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType39
OBJECT-TYPE
DiffServ Type 39 : IP ToS value = 156
1.3.6.1.4.1.171.10.75.16.1.12.6.2.40INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType40
OBJECT-TYPE
DiffServ Type 40 : IP ToS value = 160
1.3.6.1.4.1.171.10.75.16.1.12.6.2.41INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType41
OBJECT-TYPE
DiffServ Type 41 : IP ToS value = 164
1.3.6.1.4.1.171.10.75.16.1.12.6.2.42INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType42
OBJECT-TYPE
DiffServ Type 42 : IP ToS value = 168
1.3.6.1.4.1.171.10.75.16.1.12.6.2.43INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType43
OBJECT-TYPE
DiffServ Type 43 : IP ToS value = 172
1.3.6.1.4.1.171.10.75.16.1.12.6.2.44INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType44
OBJECT-TYPE
DiffServ Type 44 : IP ToS value = 176
1.3.6.1.4.1.171.10.75.16.1.12.6.2.45INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType45
OBJECT-TYPE
DiffServ Type 45 : IP ToS value = 180
1.3.6.1.4.1.171.10.75.16.1.12.6.2.46INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType46
OBJECT-TYPE
DiffServ Type 46 : IP ToS value = 184
1.3.6.1.4.1.171.10.75.16.1.12.6.2.47INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType47
OBJECT-TYPE
DiffServ Type 47 : IP ToS value = 188
1.3.6.1.4.1.171.10.75.16.1.12.6.2.48INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType48
OBJECT-TYPE
DiffServ Type 48 : IP ToS value = 192
1.3.6.1.4.1.171.10.75.16.1.12.6.2.49INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType49
OBJECT-TYPE
DiffServ Type 49 : IP ToS value = 196
1.3.6.1.4.1.171.10.75.16.1.12.6.2.50INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType50
OBJECT-TYPE
DiffServ Type 50 : IP ToS value = 200
1.3.6.1.4.1.171.10.75.16.1.12.6.2.51INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType51
OBJECT-TYPE
DiffServ Type 51 : IP ToS value = 204
1.3.6.1.4.1.171.10.75.16.1.12.6.2.52INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType52
OBJECT-TYPE
DiffServ Type 52 : IP ToS value = 208
1.3.6.1.4.1.171.10.75.16.1.12.6.2.53INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType53
OBJECT-TYPE
DiffServ Type 53 : IP ToS value = 212
1.3.6.1.4.1.171.10.75.16.1.12.6.2.54INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType54
OBJECT-TYPE
DiffServ Type 54 : IP ToS value = 216
1.3.6.1.4.1.171.10.75.16.1.12.6.2.55INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType55
OBJECT-TYPE
DiffServ Type 55 : IP ToS value = 220
1.3.6.1.4.1.171.10.75.16.1.12.6.2.56INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType56
OBJECT-TYPE
DiffServ Type 56 : IP ToS value = 224
1.3.6.1.4.1.171.10.75.16.1.12.6.2.57INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType57
OBJECT-TYPE
DiffServ Type 57 : IP ToS value = 228
1.3.6.1.4.1.171.10.75.16.1.12.6.2.58INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType58
OBJECT-TYPE
DiffServ Type 58 : IP ToS value = 232
1.3.6.1.4.1.171.10.75.16.1.12.6.2.59INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType59
OBJECT-TYPE
DiffServ Type 59 : IP ToS value = 236
1.3.6.1.4.1.171.10.75.16.1.12.6.2.60INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType60
OBJECT-TYPE
DiffServ Type 60 : IP ToS value = 240
1.3.6.1.4.1.171.10.75.16.1.12.6.2.61INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType61
OBJECT-TYPE
DiffServ Type 61 : IP ToS value = 244
1.3.6.1.4.1.171.10.75.16.1.12.6.2.62INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType62
OBJECT-TYPE
DiffServ Type 62 : IP ToS value = 248
1.3.6.1.4.1.171.10.75.16.1.12.6.2.63INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosDiffServType63
OBJECT-TYPE
DiffServ Type 63 : IP ToS value = 252
1.3.6.1.4.1.171.10.75.16.1.12.6.2.64INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.6.3
qosTOSType00
OBJECT-TYPE
TOS 0
1.3.6.1.4.1.171.10.75.16.1.12.6.3.1INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType01
OBJECT-TYPE
TOS 01
1.3.6.1.4.1.171.10.75.16.1.12.6.3.2INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType02
OBJECT-TYPE
TOS 02
1.3.6.1.4.1.171.10.75.16.1.12.6.3.3INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType03
OBJECT-TYPE
TOS 03
1.3.6.1.4.1.171.10.75.16.1.12.6.3.4INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType04
OBJECT-TYPE
TOS 04
1.3.6.1.4.1.171.10.75.16.1.12.6.3.5INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType05
OBJECT-TYPE
TOS 05
1.3.6.1.4.1.171.10.75.16.1.12.6.3.6INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType06
OBJECT-TYPE
TOS 06
1.3.6.1.4.1.171.10.75.16.1.12.6.3.7INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosTOSType07
OBJECT-TYPE
TOS 07
1.3.6.1.4.1.171.10.75.16.1.12.6.3.8INTEGER {low(0), medium(1), high(2), highest(3)}read-writecurrent
qosPriSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.7
qosPriSettingsTable
OBJECT-TYPE
A list of port priority settings.
1.3.6.1.4.1.171.10.75.16.1.12.7.1not-accessiblecurrent
qosPriSettingsEntry
OBJECT-TYPE
A list of port priority settings Entries.
1.3.6.1.4.1.171.10.75.16.1.12.7.1.1not-accessiblecurrent
qosPriSetPortIndex
OBJECT-TYPE
A port identifier that is in the range of 1 to ifNumber.
1.3.6.1.4.1.171.10.75.16.1.12.7.1.1.1INTEGER (1..26)read-onlycurrent
qosPriSetPortType
OBJECT-TYPE
The port priority setting type. (ex. none = 0, 802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value is 2 + 4 = 6.
1.3.6.1.4.1.171.10.75.16.1.12.7.1.1.2INTEGER {none(0), ieee8021P(2), dscp-tos(4), ieee8021P-dscp-tos(6)}read-writecurrent
qosAclPrioritySettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.8
ipv4aclQosTable
OBJECT-TYPE
A list of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.1not-accessiblecurrent
ipv4aclQosEntry
OBJECT-TYPE
A list of priority by acl setting entry.
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1not-accessiblecurrent
ipv4aclQosIndex
OBJECT-TYPE
Index of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.1Integer32 (1..65535)read-onlycurrent
ipv4aclQosType
OBJECT-TYPE
Type of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.2INTEGER {mac(0), ip(1), tcp(2), udp(3), vlanid(4), protocol(5)}read-writecurrent
ipv4aclQosMACAddr
OBJECT-TYPE
Dst MAC of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.3MacAddressread-writecurrent
ipv4aclQosIPAddr
OBJECT-TYPE
Dst IP of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.4IpAddressread-writecurrent
ipv4aclQosTCPUDPPort
OBJECT-TYPE
Dst TCP/UDP port of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.5Integer32 (1..65535)read-writecurrent
ipv4aclQosVlanID
OBJECT-TYPE
VLAN ID of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.6Integer32 (1..4094)read-writecurrent
ipv4aclQosProtocol
OBJECT-TYPE
Ip protocol number of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.7Integer32 (1..255)read-writecurrent
ipv4aclQosAssignClass
OBJECT-TYPE
Be mapped class of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.8INTEGER {class0(0), class1(1), class2(2), class3(3)}read-writecurrent
ipv4aclQosStatus
OBJECT-TYPE
Status of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.1.1.9RowStatusread-writecurrent
aclQosTable
OBJECT-TYPE
A list of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.2not-accessiblecurrent
aclQosEntry
OBJECT-TYPE
A list of priority by acl setting entry.
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1not-accessiblecurrent
aclQosIndex
OBJECT-TYPE
Index of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.1Integer32 (1..65535)read-onlycurrent
aclQosType
OBJECT-TYPE
Type of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.2INTEGER {mac(0), ip(1), tcp(2), udp(3), vlanid(4), protocol(5), ipv6(6), ipv6traffic-class(7)}read-writecurrent
aclQosMACAddr
OBJECT-TYPE
Dst MAC of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.3MacAddressread-writecurrent
aclQosIPAddr
OBJECT-TYPE
Dst IP of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.4IpAddressread-writecurrent
aclQosIPv6Addr
OBJECT-TYPE
Dst IP of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.5Ipv6Addressread-writecurrent
aclQosTCPUDPPort
OBJECT-TYPE
Dst TCP/UDP port of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.6Integer32 (1..65535)read-writecurrent
aclQosVlanID
OBJECT-TYPE
VLAN ID of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.7Integer32 (1..4094)read-writecurrent
aclQosProtocol
OBJECT-TYPE
Ip protocol number of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.8Integer32 (1..255)read-writecurrent
aclQosIP6TC
OBJECT-TYPE
Ipv6 Traffic Class number of priority by acl setting
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.10Integer32 (0..255)read-writecurrent
aclQosAssignClass
OBJECT-TYPE
Be mapped class of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.98INTEGER {class0(0), class1(1), class2(2), class3(3)}read-writecurrent
aclQosStatus
OBJECT-TYPE
Status of priority by acl setting.
1.3.6.1.4.1.171.10.75.16.1.12.8.2.1.99RowStatusread-writecurrent
cosBandwidthCtrlSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.12.9
cosBandwidthCtrlTable
OBJECT-TYPE
A list of cosBandwidthCtrlEntry default priority Entries.
1.3.6.1.4.1.171.10.75.16.1.12.9.1not-accessiblecurrent
cosBandwidthCtrlEntry
OBJECT-TYPE
A list of cosBandwidthCtrlEntry default priority priorities.
1.3.6.1.4.1.171.10.75.16.1.12.9.1.1not-accessiblecurrent
cosBandwidthCtrlPortIndex
OBJECT-TYPE
A port identifier that is in the range of 1 to ifNumber.
1.3.6.1.4.1.171.10.75.16.1.12.9.1.1.1Integer32 (1..26)read-onlycurrent
cosBandwidthCtrlClassIndex
OBJECT-TYPE
A BandwidthCtrlClassIndex identifier that is in the range of 1 to ifNumber.
1.3.6.1.4.1.171.10.75.16.1.12.9.1.1.2INTEGER (0..3)read-onlycurrent
cosBandwidthValue
OBJECT-TYPE
The BandwidthValue return value.
1.3.6.1.4.1.171.10.75.16.1.12.9.1.1.3Integer32read-writecurrent
cosBandwidthEffectiveRX
OBJECT-TYPE
A speed rate of Effective RX.
1.3.6.1.4.1.171.10.75.16.1.12.9.1.1.4Integer32read-onlycurrent
cosBandwidthEffectiveTX
OBJECT-TYPE
A speed value of Effective TX.
1.3.6.1.4.1.171.10.75.16.1.12.9.1.1.5Integer32read-onlycurrent
companyTrafficMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.13
bandwidthCtrlSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.13.1
bandwidthCtrlTable
OBJECT-TYPE
A table to control the rate limiting parameters either for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.16.1.13.1.2not-accessiblecurrent
bandwidthCtrlEntry
OBJECT-TYPE
An entry appears in this table for each physical interface in the switch.
1.3.6.1.4.1.171.10.75.16.1.13.1.2.1not-accessiblecurrent
bandwidthCtrlIndex
OBJECT-TYPE
The interface index for which the configuration in this entry applies. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.13.1.2.1.1Integer32 (1..26)read-onlycurrent
bandwidthCtrlTxThreshold
OBJECT-TYPE
Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000 (Kbits per second) in GE port.
1.3.6.1.4.1.171.10.75.16.1.13.1.2.1.2Integer32 (0 | 64..1024000)read-writecurrent
bandwidthCtrlRxThreshold
OBJECT-TYPE
Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware. The value can be set between 64~102400(Kbits per second) in FE port, 64~1024000(Kbits per second) in GE port.
1.3.6.1.4.1.171.10.75.16.1.13.1.2.1.3Integer32 (0 | 64..1024000)read-writecurrent
bandwidthEffecTxThreshold
OBJECT-TYPE
This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed.
1.3.6.1.4.1.171.10.75.16.1.13.1.2.1.4Integer32read-onlycurrent
bandwidthEffecRxThreshold
OBJECT-TYPE
Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets on this interface. The value that can be set for this object is limited by the underlying hardware.
1.3.6.1.4.1.171.10.75.16.1.13.1.2.1.5Integer32read-onlycurrent
trafficCtrlSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.13.4
trafficCtrlTrap
OBJECT-TYPE
The trap setting of traffic control.
1.3.6.1.4.1.171.10.75.16.1.13.4.1INTEGER {none(0), stormOccurred(1), stormCleared(2), both(3)}read-writecurrent
trafficCtrlTable
OBJECT-TYPE
The traffic control table.
1.3.6.1.4.1.171.10.75.16.1.13.4.2not-accessiblecurrent
trafficCtrlEntry
OBJECT-TYPE
The traffic control entry.
1.3.6.1.4.1.171.10.75.16.1.13.4.2.1not-accessiblecurrent
trafficCtrlIndex
OBJECT-TYPE
The traffic control index.
1.3.6.1.4.1.171.10.75.16.1.13.4.2.1.1Integer32 (1..65535)read-onlycurrent
trafficCtrlActionMode
OBJECT-TYPE
The action mode of traffic control.
1.3.6.1.4.1.171.10.75.16.1.13.4.2.1.2INTEGER {drop(0), shutdown(1)}read-writecurrent
trafficCtrlType
OBJECT-TYPE
The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast)
1.3.6.1.4.1.171.10.75.16.1.13.4.2.1.3INTEGER {none(0), b(1), m(2), mb(3), u(4), ub(5), um(6), umb(7)}read-writecurrent
trafficCtrlThreshold
OBJECT-TYPE
The threshold of traffic control.
1.3.6.1.4.1.171.10.75.16.1.13.4.2.1.4Integer32 (1..102400)read-writecurrent
trafficCtrlCountDown
OBJECT-TYPE
The count down value of traffic control.
1.3.6.1.4.1.171.10.75.16.1.13.4.2.1.5Integer32 (0..30)read-writecurrent
trafficCtrlTimeInterval
OBJECT-TYPE
The time interval of traffic control.
1.3.6.1.4.1.171.10.75.16.1.13.4.2.1.6Integer32 (5..30)read-writecurrent
trafficCtrlAutoRecoverTime
OBJECT-TYPE
The recover time of traffic control.
1.3.6.1.4.1.171.10.75.16.1.13.4.3Integer32 (0..65535)read-writecurrent
companySecurity
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14
securityTrustedHost
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.1
trustedHostStatus
OBJECT-TYPE
This object indicates trusted host function is enabled or disabled. When trusted host function is enabled, D-Link Smart Switches will only allow hosts which you trust to access and control the switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.
1.3.6.1.4.1.171.10.75.16.1.14.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
ipv4trustedHostTable
OBJECT-TYPE
A table to configure trusted host in the system.
1.3.6.1.4.1.171.10.75.16.1.14.1.2not-accessibleobsolete
ipv4trustedHostEntry
OBJECT-TYPE
Each entry in this table represents rules for particular trusted host.
1.3.6.1.4.1.171.10.75.16.1.14.1.2.1not-accessibleobsolete
ipv4trustedHostIpAddr
OBJECT-TYPE
The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.
1.3.6.1.4.1.171.10.75.16.1.14.1.2.1.1IpAddressread-onlyobsolete
ipv4trustedHostIpMask
OBJECT-TYPE
Used to mask with IP address, it allow you set a subnet as a trusted host entry.
1.3.6.1.4.1.171.10.75.16.1.14.1.2.1.2IpAddressread-onlyobsolete
ipv4trustedHostRowStatus
OBJECT-TYPE
The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.14.1.2.1.3RowStatusread-createobsolete
trustedHostTable
OBJECT-TYPE
A table to configure trusted host for in the system.
1.3.6.1.4.1.171.10.75.16.1.14.1.3not-accessiblecurrent
trustedHostEntry
OBJECT-TYPE
Each entry in this table represents rules for particular trusted host.
1.3.6.1.4.1.171.10.75.16.1.14.1.3.1not-accessiblecurrent
trustedHostIPType
OBJECT-TYPE
Type of IP interface.
1.3.6.1.4.1.171.10.75.16.1.14.1.3.1.1INTEGER {iPv4(1), iPv6(2)}read-onlycurrent
trustedHostIpAddr
OBJECT-TYPE
The IP address of host you allow to access to D-Link Smart Switch. Your local host IPv4/6 Addresses must be one of the IP Addresses to avoid disconnection.
1.3.6.1.4.1.171.10.75.16.1.14.1.3.1.2Ipv6Addressread-onlycurrent
trustedHostIpMask
OBJECT-TYPE
Used to mask with IPv4/6 address, it allow you set a subnet as a trusted host entry.
1.3.6.1.4.1.171.10.75.16.1.14.1.3.1.3Ipv6Addressread-onlycurrent
trustedHostRowStatus
OBJECT-TYPE
The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.14.1.3.1.4RowStatusread-createcurrent
securityPortSecurity
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.2
portSecTable
OBJECT-TYPE
A table to control port security features of the device.
1.3.6.1.4.1.171.10.75.16.1.14.2.1not-accessiblecurrent
portSecEntry
OBJECT-TYPE
An entry appears in port security table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.2.1.1not-accessiblecurrent
portSecIndex
OBJECT-TYPE
The interface index for which the configuration in this entry applies. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.14.2.1.1.1Integer32 (1..26)read-onlycurrent
portSecState
OBJECT-TYPE
Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding table can not be changed once the port security admin state is enabled.
1.3.6.1.4.1.171.10.75.16.1.14.2.1.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
portSecMLA
OBJECT-TYPE
Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 64. Note: Set value 0 means cannot learn MAC address.
1.3.6.1.4.1.171.10.75.16.1.14.2.1.1.3Integer32 (0..64)read-writecurrent
portSecLockAddrMode
OBJECT-TYPE
Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTimeout : The locked addresses will age out after the aging timer expires. Permanent : The locked addresses will not age out after the aging timer expires.
1.3.6.1.4.1.171.10.75.16.1.14.2.1.1.4INTEGER {deleteOnReset(1), deleteOnTimeout(2), permanent(3)}read-writecurrent
portSecFDBPermanentTable
OBJECT-TYPE
A table to control port security FDB Permanent of the device.
1.3.6.1.4.1.171.10.75.16.1.14.2.2not-accessiblecurrent
portSecFDBPermanentEntry
OBJECT-TYPE
An entry appears in port security table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.2.2.1not-accessiblecurrent
portSecFDBPermIndex
OBJECT-TYPE
The index of the port security MAC entry. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.14.2.2.1.1INTEGER (1..26)read-onlycurrent
portSecFDBPermVlanID
OBJECT-TYPE
The VLAN ID of the port security MAC entry.
1.3.6.1.4.1.171.10.75.16.1.14.2.2.1.2INTEGERread-onlycurrent
portSecFDBPermMac
OBJECT-TYPE
The MAC address associated of the port security MAC entry.
1.3.6.1.4.1.171.10.75.16.1.14.2.2.1.3MacAddressread-onlycurrent
portSecFDBPermPort
OBJECT-TYPE
The forwarding port of the port security MAC entry. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.14.2.2.1.4INTEGER (1..26)read-onlycurrent
securityARPSpoofPrevent
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.3
aRPSpoofPreventTable
OBJECT-TYPE
A table to control ARP Spoofing prevention for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.16.1.14.3.1not-accessiblecurrent
aRPSpoofPreventEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.3.1.1not-accessiblecurrent
aRPSpoofPreventIpAddr
OBJECT-TYPE
Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.
1.3.6.1.4.1.171.10.75.16.1.14.3.1.1.1IpAddressnot-accessiblecurrent
aRPSpoofPreventMacAddress
OBJECT-TYPE
Ethernet Mac Address.
1.3.6.1.4.1.171.10.75.16.1.14.3.1.1.2MacAddressread-writecurrent
aRPSpoofPreventPortList
OBJECT-TYPE
Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.
1.3.6.1.4.1.171.10.75.16.1.14.3.1.1.3PortListread-writecurrent
aRPSpoofPreventRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.14.3.1.1.4RowStatusread-createcurrent
securitySSL
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.5
sslSecurityHttpStatus
OBJECT-TYPE
This object is for enabling or disabling secure HTTP in the system.
1.3.6.1.4.1.171.10.75.16.1.14.5.1INTEGER {enable(1), disable(2)}read-writecurrent
sslCiphers
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.5.2
sslCipherSuiteList
OBJECT-TYPE
This object is to configure the cipher-suites list.
1.3.6.1.4.1.171.10.75.16.1.14.5.2.1Bits {rsa-null-md5(0), rsa-null-sha(1), rsa-des-sha(2), rsa-3des-sha(3), dh-rsa-des-sha(4), dh-rsa-3des-sha(5), rsa-exp1024-des-sha(6)}read-writecurrent
securityDhcpServerScreen
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.7
dhcpServerScreenEnablePortlist
OBJECT-TYPE
To enable or disable DHCP Server Screening port list.
1.3.6.1.4.1.171.10.75.16.1.14.7.1PortListread-writecurrent
dhcpServerScreenEnableVlanlist
OBJECT-TYPE
To enable or disable DHCP Server Screening vlan list.
1.3.6.1.4.1.171.10.75.16.1.14.7.2OCTET STRINGread-writecurrent
dhcpServerScreenLogSuppressDuration
OBJECT-TYPE
DSS Trap Log Suppress Duration.
1.3.6.1.4.1.171.10.75.16.1.14.7.3INTEGER {one-min(1), five-min(5), thirty-min(30)}read-writecurrent
filterDHCPServerTable
OBJECT-TYPE
A table to control filter DHCP Server for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.16.1.14.7.4not-accessiblecurrent
filterDHCPServerEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.7.4.1not-accessiblecurrent
filterDHCPServerIpAddr
OBJECT-TYPE
Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.
1.3.6.1.4.1.171.10.75.16.1.14.7.4.1.1IpAddressnot-accessiblecurrent
filterDHCPServerClientMacAddr
OBJECT-TYPE
Ethernet Mac Address.
1.3.6.1.4.1.171.10.75.16.1.14.7.4.1.2MacAddressnot-accessiblecurrent
filterDHCPServerPortList
OBJECT-TYPE
Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.
1.3.6.1.4.1.171.10.75.16.1.14.7.4.1.3PortListread-writecurrent
filterDHCPServerVlanList
OBJECT-TYPE
Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.
1.3.6.1.4.1.171.10.75.16.1.14.7.4.1.4OCTET STRINGread-writecurrent
filterDHCPServerRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.14.7.4.1.99RowStatusread-createcurrent
securitySSH
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.8
sshSecurityStatus
OBJECT-TYPE
This object is for enabling or disabling ssh in the system.
1.3.6.1.4.1.171.10.75.16.1.14.8.1INTEGER {enable(1), disable(2)}read-writecurrent
sshMaxAuthFailAttempts
OBJECT-TYPE
This object indicates the max auth fail retry attempt times.
1.3.6.1.4.1.171.10.75.16.1.14.8.2INTEGER (2..20)read-writecurrent
sshSessionKeyRekeying
OBJECT-TYPE
This object indicates one SSH session rekey time interval.
1.3.6.1.4.1.171.10.75.16.1.14.8.3INTEGER {never(0), ten-min(1), thirty-min(2), sixty-min(3)}read-writecurrent
sshMaxSession
OBJECT-TYPE
This object indicates max SSH session number supported in system.
1.3.6.1.4.1.171.10.75.16.1.14.8.4INTEGER (1..8)read-writecurrent
sshConnectionTimeout
OBJECT-TYPE
This object indicates SSH connection timeout value.
1.3.6.1.4.1.171.10.75.16.1.14.8.5INTEGER (120..600)read-writecurrent
sshAuthenMethodPassWordAdmin
OBJECT-TYPE
The object indicates authen method password is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.14.8.6INTEGER {enable(1), disable(2)}read-writecurrent
sshAuthenMethodPubKeyAdmin
OBJECT-TYPE
The object indicates authen method public-key is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.14.8.7INTEGER {enable(1), disable(2)}read-writecurrent
sshAuthenMethodHostKeyAdmin
OBJECT-TYPE
The object indicates authen method host-key is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.14.8.8INTEGER {enable(1), disable(2)}read-writecurrent
sshCipherSuiteList
OBJECT-TYPE
This object is to configure the cipher-suites list.
1.3.6.1.4.1.171.10.75.16.1.14.8.9Bits {tripleDESCBC(0)}read-onlycurrent
sshMacSuiteList
OBJECT-TYPE
This object is to configure the MAC-list.
1.3.6.1.4.1.171.10.75.16.1.14.8.10Bits {hMAC-SHA1(0), hMAC-MD5(1)}read-writecurrent
sshPublKeyRSAAdmin
OBJECT-TYPE
The object indicates Public key generating algorithm RSA is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.14.8.11INTEGER {enabled(1), disabled(2)}read-writecurrent
sshUserInfoTable
OBJECT-TYPE
A table to configure SSH user auth in the system.
1.3.6.1.4.1.171.10.75.16.1.14.8.12not-accessiblecurrent
sshUserInfoEntry
OBJECT-TYPE
An entry to configure user auth in the system.
1.3.6.1.4.1.171.10.75.16.1.14.8.12.1not-accessiblecurrent
sshUserInfoID
OBJECT-TYPE
The Schedule identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 8.
1.3.6.1.4.1.171.10.75.16.1.14.8.12.1.1Integer32 (1..8)read-onlycurrent
sshUserInfoUserName
OBJECT-TYPE
The ssh user name associated with the SSH suer Info. entry (e.g., `admin, user').
1.3.6.1.4.1.171.10.75.16.1.14.8.12.1.2DisplayString (SIZE(1..20))read-onlycurrent
sshUserInfoAuth
OBJECT-TYPE
The object indicates which auth used by the user.
1.3.6.1.4.1.171.10.75.16.1.14.8.12.1.3INTEGER {hostbased(1), password(2), publickey(4)}read-writecurrent
sshUserInfoHostName
OBJECT-TYPE
The ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2').
1.3.6.1.4.1.171.10.75.16.1.14.8.12.1.4DisplayString (SIZE(1..20))read-writecurrent
sshUserInfoHostIp
OBJECT-TYPE
SSH HostBased IP Address of the system.
1.3.6.1.4.1.171.10.75.16.1.14.8.12.1.5IpAddressread-writecurrent
securityTrafficSeg
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.9
trafficSegTable
OBJECT-TYPE
A Port-channel is created through ifMain table. After the creation of the port-channel, corresponding logical interface will be created in the ifMain table. This Port-channel table is indexed through Key values and allows to configure link selection policy and the Mac address for the port-channel. All other objects in this table displays the details of the port-channel
1.3.6.1.4.1.171.10.75.16.1.14.9.1not-accessiblecurrent
trafficSegEntry
OBJECT-TYPE
There is one entry in this table for each created port-channel port
1.3.6.1.4.1.171.10.75.16.1.14.9.1.1not-accessiblecurrent
trafficSegIfIndex
OBJECT-TYPE
The ifIndex of the port-channel(Aggregator's interface index).
1.3.6.1.4.1.171.10.75.16.1.14.9.1.1.1InterfaceIndexread-onlycurrent
trafficSegMemberList
OBJECT-TYPE
Port list of port channel.
1.3.6.1.4.1.171.10.75.16.1.14.9.1.1.2PortListread-writecurrent
securityIpMacPortBinding
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.10
impbSettingTable
OBJECT-TYPE
A table to control IP-MAC-Port Binding Setting features of the device.
1.3.6.1.4.1.171.10.75.16.1.14.10.1not-accessiblecurrent
impbSettingEntry
OBJECT-TYPE
An entry appears in IP-MAC-Port Binding Setting table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1not-accessiblecurrent
impbPortIndex
OBJECT-TYPE
Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.1INTEGER (1..26)read-onlycurrent
impbPortState
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding admin state for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
impbPortDHCPSnoopingState
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding DHCP snooping state for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.4INTEGER {disabled(0), enabled(1)}read-writecurrent
impbPortArpInspectionState
OBJECT-TYPE
Set IP-MAC-Port Binding ARP Inspection state for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.5INTEGER {disabled(0), strict(1), loose(2)}read-writecurrent
impbPortIpInspectionState
OBJECT-TYPE
Set IP-MAC-Port Binding IP Inspection state for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.6INTEGER {disabled(0), enabled(1)}read-writecurrent
impbPortAllowZeroIPState
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding Allow-Zero-IP state for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.7INTEGER {disabled(0), enabled(1)}read-writecurrent
impbPortForwardDHCPPktState
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding Forward-DHCP-Packet state for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.8INTEGER {disabled(0), enabled(1)}read-writecurrent
impbPortDHCPMaxEntryIPv4
OBJECT-TYPE
Set the maximum number of IPv4 entries that can be learned for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.9Integer32 (0..10)read-writecurrent
impbPortDHCPMaxEntryIPv6
OBJECT-TYPE
Set the maximum number of IPv6 entries that can be learned for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.10Integer32 (0..10)read-writecurrent
impbPortNDInspectionState
OBJECT-TYPE
Set IP-MAC-Port Binding ND Inspection state for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.11INTEGER {disabled(0), enabled(1)}read-writecurrent
impbPortProtocolState
OBJECT-TYPE
Set IP-MAC-Port Binding protocol state for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.12INTEGER {ipv4(0), ipv6(1), all(2)}read-writecurrent
impbPortDHCPv4SetVlanList
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.13OCTET STRING (SIZE(0..512))read-writecurrent
impbPortDHCPv4VlanList1k
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCP snooping, the bit corresponding to that VLAN is set to '1'.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.14OCTET STRING (SIZE(0..128))read-onlycurrent
impbPortDHCPv4VlanList2k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1025 through 2048. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv4 snooping, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.15OCTET STRING (SIZE(0..128))read-onlycurrent
impbPortDHCPv4VlanList3k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2049 through 3072. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv4 snooping the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.16OCTET STRING (SIZE(0..128))read-onlycurrent
impbPortDHCPv4VlanList4k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3073 through 4094. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv4 snooping, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.17OCTET STRING (SIZE(0..128))read-onlycurrent
impbPortDHCPv6SetVlanList
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. The set of vlans configured by management to map for this Instance. If the VlanId to Instance Mapping has to be known then any one of the VlanMapped object should be used.If a vlan is already mapped to this Instance, it may not be mapped again. This object is used only for SET operation. GET Operation returns null values.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.18OCTET STRING (SIZE(0..512))read-writecurrent
impbPortDHCPv6VlanList1k
OBJECT-TYPE
A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCP snooping, the bit corresponding to that VLAN is set to '1'.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.19OCTET STRING (SIZE(0..128))read-onlycurrent
impbPortDHCPv6VlanList2k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1025 through 2048. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv6 snooping, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.20OCTET STRING (SIZE(0..128))read-onlycurrent
impbPortDHCPv6VlanList3k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2049 through 3072. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv6 snooping the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.21OCTET STRING (SIZE(0..128))read-onlycurrent
impbPortDHCPv6VlanList4k
OBJECT-TYPE
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3073 through 4094. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this DHCPv6 snooping, the bit corresponding to that VLAN is set to '1'. This object is only instantiated on devices with support for VlanIndex values up to 4094.
1.3.6.1.4.1.171.10.75.16.1.14.10.1.1.22OCTET STRING (SIZE(0..128))read-onlycurrent
impbAutoScanTable
OBJECT-TYPE
A table to control auto scan features of the device.
1.3.6.1.4.1.171.10.75.16.1.14.10.2not-accessiblecurrent
impbAutoScanEntry
OBJECT-TYPE
An entry appears in auto scan table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.10.2.1not-accessiblecurrent
impbAutoScanMacAddress
OBJECT-TYPE
The MAC address associated of the auto scan entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.2.1.1MacAddressread-onlycurrent
impbAutoScanPort
OBJECT-TYPE
The port number of the auto scan entry. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.14.10.2.1.2Integer32 (1..26)read-onlycurrent
impbAutoScanIpAddress
OBJECT-TYPE
The IP address associated of the auto scan entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.2.1.3DisplayStringread-onlycurrent
impbAutoScanVlanId
OBJECT-TYPE
The VLAN ID of the auto scan entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.2.1.4Integer32read-onlycurrent
impbAutoScanBinding
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding for the entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.2.1.5INTEGER {disabled(0), enabled(1)}read-writecurrent
impbBindingListTable
OBJECT-TYPE
A table to control Manual IP-MAC-Port Binding white list features of the device.
1.3.6.1.4.1.171.10.75.16.1.14.10.3not-accessiblecurrent
impbBindingListEntry
OBJECT-TYPE
An entry appears in Manual IP-MAC-Port Binding white list table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.10.3.1not-accessiblecurrent
impbBindingListIpAddress
OBJECT-TYPE
The IP address associated of the Manual IP-MAC-PORT Binding white list entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.3.1.1DisplayStringread-onlycurrent
impbBindingListMacAddress
OBJECT-TYPE
The MAC address associated of the Manual IP-MAC-PORT Binding white list entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.3.1.2MacAddressread-onlycurrent
impbBindingListPort
OBJECT-TYPE
The port number of the Manual IP-MAC-PORT Binding white list entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.3.1.3Integer32read-writecurrent
impbBindingListRowStatus
OBJECT-TYPE
The status of a row in impbBindingListTable. By setting this object, new entries can be created in impbBindingListTable and existing entries can be removed from impbBindingListTable. It can be used as specified in the SNMP v2 standard.
1.3.6.1.4.1.171.10.75.16.1.14.10.3.1.4RowStatusread-createcurrent
impbBlockListTable
OBJECT-TYPE
A table to control IP-MAC-Port Binding black list of the device.
1.3.6.1.4.1.171.10.75.16.1.14.10.4not-accessiblecurrent
impbBlockListEntry
OBJECT-TYPE
An entry appears in Manual IP-MAC-Port Binding black list table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.10.4.1not-accessiblecurrent
impbBlockListMacAddress
OBJECT-TYPE
The MAC address associated of the IP-MAC-PORT Binding black list entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.4.1.1MacAddressread-onlycurrent
impbBlockListVlanId
OBJECT-TYPE
The VLAN ID of the IP-MAC-PORT Binding black list entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.4.1.2Integer32 (1..4094)read-onlycurrent
impbBlockListPort
OBJECT-TYPE
The port number of the IP-MAC-PORT Binding black list entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.4.1.3Integer32 (1..26)read-onlycurrent
impbBlockListIpAddress
OBJECT-TYPE
The IP address associated of the IP-MAC-PORT Binding black list entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.4.1.4DisplayStringread-onlycurrent
impbBlockListStatus
OBJECT-TYPE
nothing/delete IP-MAC-Port Binding for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.4.1.5INTEGER {nothing(0), deleted(1)}read-writecurrent
impbAutoScanIpAddressFrom
OBJECT-TYPE
The begin for IP address associated of the IP-MAC-PORT Binding auto scan entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.5Ipv6Addressread-writecurrent
impbAutoScanIpAddressTo
OBJECT-TYPE
The end for IP address associated of the IP-MAC-PORT Binding auto scan entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.6Ipv6Addressread-writecurrent
impbAutoScanStatus
OBJECT-TYPE
Nothing / scan IP-MAC-Port Binding auto scan for the interface.
1.3.6.1.4.1.171.10.75.16.1.14.10.7INTEGER {nothing(0), scan(1)}read-writecurrent
impbDhcpSnoopingTable
OBJECT-TYPE
A table to display DHCP snooping entries of the device.
1.3.6.1.4.1.171.10.75.16.1.14.10.8not-accessiblecurrent
impbDhcpSnoopingEntry
OBJECT-TYPE
An entry appears in DHCP snooping table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.14.10.8.1not-accessiblecurrent
impbDhcpSnoopingMacAddress
OBJECT-TYPE
The MAC address associated of the DHCP snooping entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.8.1.1MacAddressread-onlycurrent
impbDhcpSnoopingIpAddress
OBJECT-TYPE
The IP address associated of the DHCP snooping entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.8.1.2Ipv6Addressread-onlycurrent
impbDhcpSnoopingLeaseTime
OBJECT-TYPE
The lease time associated of the DHCP snooping entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.8.1.3Integer32read-onlycurrent
impbDhcpSnoopingPort
OBJECT-TYPE
The port number associated of the DHCP snooping entry.
1.3.6.1.4.1.171.10.75.16.1.14.10.8.1.4Integer32read-onlycurrent
impbRoamingState
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding roaming state.
1.3.6.1.4.1.171.10.75.16.1.14.10.9INTEGER {disabled(0), enabled(1)}read-writecurrent
impbVlanModeState
OBJECT-TYPE
Disable / enable IP-MAC-Port Binding vlan mode state.
1.3.6.1.4.1.171.10.75.16.1.14.10.10INTEGER {disabled(0), enabled(1)}read-writecurrent
impbVlanModeVlanList
OBJECT-TYPE
IP-MAC-Port Binding vlan mode VID list.
1.3.6.1.4.1.171.10.75.16.1.14.10.11PortListread-writecurrent
impbLogState
OBJECT-TYPE
Configure IP-MAC-Port Binding log state.
1.3.6.1.4.1.171.10.75.16.1.14.10.12INTEGER {disabled(0), ipv4(1), ipv6(2), all(3)}read-writecurrent
impbDHCPv6PrefixDelegationSnoopState
OBJECT-TYPE
Configure DHCPv6 PD snooping state.
1.3.6.1.4.1.171.10.75.16.1.14.10.13INTEGER {disabled(0), enabled(1)}read-writecurrent
impbBindingtraplog
OBJECT-TYPE
This object is for enabling or disabling topology change event trap in the system.
1.3.6.1.4.1.171.10.75.16.1.14.10.14INTEGER {enabled(1), disabled(2)}read-writecurrent
impbBindingtrap
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.10.15
impbAutoScanCurrentStatus
OBJECT-TYPE
Show Auto scan status
1.3.6.1.4.1.171.10.75.16.1.14.10.16INTEGER {stop(0), scanning(1)}read-onlycurrent
securityAAC
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.11
aacAuthenAdminState
OBJECT-TYPE
This object indicates the Access Authentication is enable or disable.
1.3.6.1.4.1.171.10.75.16.1.14.11.1INTEGER {enabled(1), disabled(2)}read-writecurrent
aacAuthParamResponseTimeout
OBJECT-TYPE
Timeout in second for login authentication response.
1.3.6.1.4.1.171.10.75.16.1.14.11.2INTEGER (0..255)read-writecurrent
aacAuthParamAttempt
OBJECT-TYPE
The amount for login authentication, if login failure exceed, connection or access would be locked.
1.3.6.1.4.1.171.10.75.16.1.14.11.3INTEGER (1..255)read-writecurrent
aacAPAuthMethodGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.11.4
aacAPLoginMethod
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.11.4.1
aacAPConsoleLoginMethod
OBJECT-TYPE
Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console
1.3.6.1.4.1.171.10.75.16.1.14.11.4.1.1INTEGER (1..8)read-writecurrent
aacAPTelnetLoginMethod
OBJECT-TYPE
Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.
1.3.6.1.4.1.171.10.75.16.1.14.11.4.1.2INTEGER (1..8)read-writecurrent
aacAPSSHLoginMethod
OBJECT-TYPE
Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH.
1.3.6.1.4.1.171.10.75.16.1.14.11.4.1.3INTEGER (1..8)read-writecurrent
aacAPHttpLoginMethod
OBJECT-TYPE
Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.
1.3.6.1.4.1.171.10.75.16.1.14.11.4.1.4INTEGER (1..8)read-writecurrent
aacAPEnableMethod
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.11.4.2
aacAPConsoleEnableMethod
OBJECT-TYPE
Specify the way which has to execute authentication while login the system and the method for authentication.Access system via local console.
1.3.6.1.4.1.171.10.75.16.1.14.11.4.2.1INTEGER (1..8)read-writecurrent
aacAPTelnetEnableMethod
OBJECT-TYPE
Specify the way which has to execute authentication while login the system and the method for authentication.Access system via telnet.
1.3.6.1.4.1.171.10.75.16.1.14.11.4.2.2INTEGER (1..8)read-writecurrent
aacAPSSHEnableMethod
OBJECT-TYPE
Specify the way which has to execute authentication while login the system and the method for authentication.Access system via SSH.
1.3.6.1.4.1.171.10.75.16.1.14.11.4.2.3INTEGER (1..8)read-writecurrent
aacAPHttpEnableMethod
OBJECT-TYPE
Specify the way which has to execute authentication while login the system and the method for authentication.Access system via HTTP.
1.3.6.1.4.1.171.10.75.16.1.14.11.4.2.4INTEGER (1..8)read-writecurrent
aacServerGroupTable
OBJECT-TYPE
A table that contains informations about server group.
1.3.6.1.4.1.171.10.75.16.1.14.11.5not-accessiblecurrent
aacServerGroupEntry
OBJECT-TYPE
A list of the group including servers.
1.3.6.1.4.1.171.10.75.16.1.14.11.5.1not-accessiblecurrent
aacServerGroupIndex
OBJECT-TYPE
A value that uniquely identifies this SwAACServerGroupEntry .
1.3.6.1.4.1.171.10.75.16.1.14.11.5.1.1INTEGER (2..9)read-onlycurrent
aacServerGroupName
OBJECT-TYPE
A human-readable text string of the method group. The name is writable only if Group is new created, which the value of aacServerGroupRowStatus is 'notReady'.
1.3.6.1.4.1.171.10.75.16.1.14.11.5.1.2OCTET STRING (SIZE(1..15))read-writecurrent
aacServersInGroup
OBJECT-TYPE
The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it.
1.3.6.1.4.1.171.10.75.16.1.14.11.5.1.3Bits {id1(0), id2(1), id3(2), id4(3), id5(4), id6(5), id7(6), id8(7), id9(8), id10(9), id11(10), id12(11), id13(12), id14(13), id15(14), id16(15)}read-writecurrent
aacServerGroupRowStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.14.11.5.1.4RowStatusread-createcurrent
iPv4aacServerInfoTable
OBJECT-TYPE
A table that contains information about severs.
1.3.6.1.4.1.171.10.75.16.1.14.11.6not-accessibleobsolete
iPv4aacServerInfoEntry
OBJECT-TYPE
A list of the information of server .
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1not-accessibleobsolete
iPv4aacServerIndex
OBJECT-TYPE
A value that uniquely identifies this SwAACServerGroupEntry.
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1.1INTEGER (1..16)read-onlyobsolete
iPv4aacServerIPAddr
OBJECT-TYPE
The IP address of Server
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1.2IpAddressread-writeobsolete
iPv4aacServerAuthProtocol
OBJECT-TYPE
The authentication protocol provided by the Server.
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1.3INTEGER {tacacsPlus(1), radius(2)}read-writeobsolete
iPv4aacServerAuthPort
OBJECT-TYPE
The TCP/IP port .
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1.4INTEGER (1..65535)read-writeobsolete
iPv4aacServerAuthKey
OBJECT-TYPE
The key used while authentication process.
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1.5OCTET STRING (SIZE(1..254))read-writeobsolete
iPv4aacServerTimeout
OBJECT-TYPE
Server response timeout .
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1.6INTEGER (1..255)read-writeobsolete
iPv4aacServerRetryCount
OBJECT-TYPE
Client retry count . (-1: No retry mechanism)
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1.7INTEGER (1..255)read-writeobsolete
iPv4aacServerRowStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.14.11.6.1.8RowStatusread-createobsolete
aacServerInfoTable
OBJECT-TYPE
A table that contains information about severs.
1.3.6.1.4.1.171.10.75.16.1.14.11.7not-accessiblecurrent
aacServerInfoEntry
OBJECT-TYPE
A list of the information of server .
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1not-accessiblecurrent
aacServerIndex
OBJECT-TYPE
A value that uniquely identifies this SwAACServerGroupEntry.
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.1INTEGER (1..16)read-onlycurrent
aacServerIPType
OBJECT-TYPE
The IP address of the AAC server IP type referred to in this table entry. (IPv4=1, IPv6=2)
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.2INTEGER (1..2)read-writecurrent
aacServerIPAddr
OBJECT-TYPE
The IP address of Server
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.3Ipv6Addressread-writecurrent
aacServerInterfaceName
OBJECT-TYPE
Specifies the interface name when the aacServerIPAddr is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.4OCTET STRINGread-createcurrent
aacServerAuthProtocol
OBJECT-TYPE
The authentication protocol provided by the Server.
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.5INTEGER {tacacsPlus(1), radius(2)}read-writecurrent
aacServerAuthPort
OBJECT-TYPE
The TCP/IP port .
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.6INTEGER (1..65535)read-writecurrent
aacServerAuthKey
OBJECT-TYPE
The key used while authentication process.
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.7OCTET STRING (SIZE(1..254))read-writecurrent
aacServerTimeout
OBJECT-TYPE
Server response timeout .
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.8INTEGER (1..255)read-writecurrent
aacServerRetryCount
OBJECT-TYPE
Client retry count . (-1: No retry mechanism)
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.9INTEGER (1..255)read-writecurrent
aacServerAccountingPort
OBJECT-TYPE
The accounting port .
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.10INTEGER (1..65535)read-writecurrent
aacServerRowStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.14.11.7.1.99RowStatusread-createcurrent
aacLoginMethodListTable
OBJECT-TYPE
A table that contains information about Login authentication method lists.
1.3.6.1.4.1.171.10.75.16.1.14.11.8not-accessiblecurrent
aacLoginMethodListEntry
OBJECT-TYPE
A list of the Authentication methods.
1.3.6.1.4.1.171.10.75.16.1.14.11.8.1not-accessiblecurrent
aacLoginMethodListIndex
OBJECT-TYPE
A value that identifies this method list.
1.3.6.1.4.1.171.10.75.16.1.14.11.8.1.1INTEGER (1..8)read-onlycurrent
aacLoginMethodListName
OBJECT-TYPE
A human-readable text string of the method list.
1.3.6.1.4.1.171.10.75.16.1.14.11.8.1.2OCTET STRING (SIZE(1..15))read-writecurrent
aacLoginMethod1
OBJECT-TYPE
The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.8.1.3INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacLoginMethod2
OBJECT-TYPE
The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.8.1.4INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacLoginMethod3
OBJECT-TYPE
The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.8.1.5INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacLoginMethod4
OBJECT-TYPE
The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.8.1.6INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacLoginMethodListRowStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.14.11.8.1.7RowStatusread-createcurrent
aacEnableMethodListTable
OBJECT-TYPE
A table that contains information about Enable authentication method lists.
1.3.6.1.4.1.171.10.75.16.1.14.11.9not-accessiblecurrent
aacEnableMethodListEntry
OBJECT-TYPE
A list of the Authentication methods.
1.3.6.1.4.1.171.10.75.16.1.14.11.9.1not-accessiblecurrent
aacEnableMethodListIndex
OBJECT-TYPE
A value that identifies this method list.
1.3.6.1.4.1.171.10.75.16.1.14.11.9.1.1INTEGER (1..8)read-onlycurrent
aacEnableMethodListName
OBJECT-TYPE
A human-readable text string of the method list.
1.3.6.1.4.1.171.10.75.16.1.14.11.9.1.2OCTET STRING (SIZE(1..15))read-writecurrent
aacEnableMethod1
OBJECT-TYPE
The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.9.1.3INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacEnableMethod2
OBJECT-TYPE
The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.9.1.4INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacEnableMethod3
OBJECT-TYPE
The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.9.1.5INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacEnableMethod4
OBJECT-TYPE
The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.9.1.6INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacEnableMethodListRowStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.14.11.9.1.7RowStatusread-createcurrent
aacLocalEnablePassword
OBJECT-TYPE
This object is used to set Local Enable Password.
1.3.6.1.4.1.171.10.75.16.1.14.11.10DisplayString (SIZE(1..15))read-writecurrent
aacAccountingMethodListTable
OBJECT-TYPE
A table that contains information about Accounting authentication method lists.
1.3.6.1.4.1.171.10.75.16.1.14.11.11not-accessiblecurrent
aacAccountingMethodListEntry
OBJECT-TYPE
A list of the Authentication methods.
1.3.6.1.4.1.171.10.75.16.1.14.11.11.1not-accessiblecurrent
aacAccountingMethodListIndex
OBJECT-TYPE
A value that identifies this method list.
1.3.6.1.4.1.171.10.75.16.1.14.11.11.1.1INTEGER (1..8)read-onlycurrent
aacAccountingMethodListName
OBJECT-TYPE
A human-readable text string of the method list.
1.3.6.1.4.1.171.10.75.16.1.14.11.11.1.2OCTET STRING (SIZE(1..15))read-writecurrent
aacAccountingMethod1
OBJECT-TYPE
The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.11.1.3INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacAccountingMethod2
OBJECT-TYPE
The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.11.1.4INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacAccountingMethod3
OBJECT-TYPE
The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.11.1.5INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacAccountingMethod4
OBJECT-TYPE
The type of Accounting method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.
1.3.6.1.4.1.171.10.75.16.1.14.11.11.1.6INTEGER {none(-1), local(0), tacacsPlus(1), radius(2)}read-writecurrent
aacAccountingMethodListRowStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.14.11.11.1.7RowStatusread-createcurrent
aacAccountingServiceIndex
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.11.12
aacAccountingServiceNetwork
OBJECT-TYPE
This object indicates aac Accounting Service Network is radius_only, default_method_list, method_list_name and disable about Accounting Service Network.
1.3.6.1.4.1.171.10.75.16.1.14.11.12.1INTEGER {disabled(-1), radius-only(0), default-method-list(1), method-list-name(2)}read-writecurrent
aacAccountingServiceShell
OBJECT-TYPE
This object indicates aac Accounting Service Shell is radius_only, default_method_list, method_list_name and disable about Accounting Service Network.
1.3.6.1.4.1.171.10.75.16.1.14.11.12.2INTEGER {disabled(-1), radius-only(0), default-method-list(1), method-list-name(2)}read-writecurrent
aacAccountingServiceSystem
OBJECT-TYPE
This object indicates aac Accounting System Shell is radius_only, default_method_list, method_list_name and disable about Accounting Service Network.
1.3.6.1.4.1.171.10.75.16.1.14.11.12.3INTEGER {disabled(-1), radius-only(0), default-method-list(1), method-list-name(2)}read-writecurrent
aacAccountingServiceCommand
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.14.11.13
aacAccountingServiceCommandAdministrator
OBJECT-TYPE
This object indicates aac Accounting Command Admin is method1, method2, method3 , method4 and disable about Accounting Service Command
1.3.6.1.4.1.171.10.75.16.1.14.11.13.1INTEGER {disabled(-1), method1(0), method2(1), method3(2), method4(3)}read-writecurrent
aacAccountingServiceCommandOperator
OBJECT-TYPE
This object indicates aac Accounting Command Operato is method1, method2, method3 , method4 and disable about Accounting Service Command
1.3.6.1.4.1.171.10.75.16.1.14.11.13.2INTEGER {disabled(-1), method1(0), method2(1), method3(2), method4(3)}read-writecurrent
aacAccountingServiceCommandPoweruser
OBJECT-TYPE
This object indicates aac Accounting Command Power user is method1, method2, method3 , method4 and disable about Accounting Service Command
1.3.6.1.4.1.171.10.75.16.1.14.11.13.3INTEGER {disabled(-1), method1(0), method2(1), method3(2), method4(3)}read-writecurrent
aacAccountingServiceCommandUser
OBJECT-TYPE
This object indicates aac Accounting Command User is method1, method2, method3 , method4 and disable about Accounting Service Command
1.3.6.1.4.1.171.10.75.16.1.14.11.13.4INTEGER {disabled(-1), method1(0), method2(1), method3(2), method4(3)}read-writecurrent
aacServerPasswordEncryption
OBJECT-TYPE
This object is used to configure server password encryption status.
1.3.6.1.4.1.171.10.75.16.1.14.11.14INTEGER {enabled(1), disabled(2)}read-writecurrent
companyACLGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.15
aclProfile
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.15.1
ipv4aclProfileTable
OBJECT-TYPE
A table to ACL profile .
1.3.6.1.4.1.171.10.75.16.1.15.1.1not-accessibleobsolete
ipv4aclProfileEntry
OBJECT-TYPE
Each entry in this table is a ACL profile. Index to the table is ACL profile ID.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1not-accessibleobsolete
ipv4aclProfileNo
OBJECT-TYPE
The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.1Integer32 (1..50)read-onlyobsolete
ipv4aclProfileType
OBJECT-TYPE
The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, arpSP_permit(4) - for ARP Spoofing prevention entry, arpSP_deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. userDefined(9) - for User Defined entry. Note that only l2, l3 and userDefined could be set by user, other is reserved for system to show information.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.2INTEGER {l2(1), l3(2), impb(3), arpSP-permit(4), arpSP-deny(5), aclQos(8), userDefined(9)}read-writeobsolete
ipv4aclProfileRuleCount
OBJECT-TYPE
The number of rules in this profile.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.3Integer32 (0..65535)read-onlyobsolete
ipv4aclProfileMask
OBJECT-TYPE
Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 ARP-SP ARP_SENDER_MAC 14 ARP-SP ARP_SENDER_IP 15 L3 TOS 16 UDF UDF1 17 UDF UDF2 18 UDF UDF3 19 UDF UDF4 20 L3v6 TRAFFIC_CLASS 21 L3v6 DST_IPV6 22 L3v6 SRC_IPV6 23 (MSB) ------------------------------------------- The value is in Hex format.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.4OCTET STRINGread-writeobsolete
ipv4aclProfileDstMacAddrMask
OBJECT-TYPE
The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.5MacAddressread-writeobsolete
ipv4aclProfileSrcMacAddrMask
OBJECT-TYPE
The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.6MacAddressread-writeobsolete
ipv4aclProfileIPProtocol
OBJECT-TYPE
Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.7INTEGER {none(0), icmp(1), igmp(2), tcp(6), udp(17), icmpv6(58), ipProtocolMask(256)}read-writeobsolete
ipv4aclProfileIPProtocolMask
OBJECT-TYPE
The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.8OCTET STRINGread-writeobsolete
ipv4aclProfileDstIpAddrMask
OBJECT-TYPE
The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.9IpAddressread-writeobsolete
ipv4aclProfileSrcIpAddrMask
OBJECT-TYPE
The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.10IpAddressread-writeobsolete
ipv4aclProfileDstPortMask
OBJECT-TYPE
The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.11OCTET STRINGread-writeobsolete
ipv4aclProfileSrcPortMask
OBJECT-TYPE
The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.12OCTET STRINGread-writeobsolete
ipv4aclProfileArpSenderMacAddrMask
OBJECT-TYPE
The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.13MacAddressread-onlyobsolete
ipv4aclProfileArpSenderIpAddrMask
OBJECT-TYPE
The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.14IpAddressread-onlyobsolete
ipv4aclProfileUdfOffsetMap
OBJECT-TYPE
Indicate which Udf field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ UDF Offset1 0 (LSB) UDF Offset2 1 UDF Offset3 2 UDF Offset4 3 ------------------------------------------- The value is in Hex format.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.15OCTET STRINGread-writeobsolete
ipv4aclUdfOffsetBase1
OBJECT-TYPE
The value of offset Base.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.16INTEGER {l2(0), l3(2), l4(3)}read-writeobsolete
ipv4aclUdfOffsetByte1
OBJECT-TYPE
The value of offset Byte from base.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.17Integer32 (0..31)read-writeobsolete
ipv4aclUdfOffsetMask1
OBJECT-TYPE
The value of offset MAsk.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.18OCTET STRINGread-writeobsolete
ipv4aclUdfOffsetBase2
OBJECT-TYPE
The value of offset Base.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.19INTEGER {l2(0), l3(2), l4(3)}read-writeobsolete
ipv4aclUdfOffsetByte2
OBJECT-TYPE
The value of offset Byte from base.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.20Integer32 (0..31)read-writeobsolete
ipv4aclUdfOffsetMask2
OBJECT-TYPE
The value of offset MAsk.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.21OCTET STRINGread-writeobsolete
ipv4aclUdfOffsetBase3
OBJECT-TYPE
The value of offset Base.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.22INTEGER {l2(0), l3(2), l4(3)}read-writeobsolete
ipv4aclUdfOffsetByte3
OBJECT-TYPE
The value of offset Byte from base.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.23Integer32 (0..31)read-writeobsolete
ipv4aclUdfOffsetMask3
OBJECT-TYPE
The value of offset MAsk.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.24OCTET STRINGread-writeobsolete
ipv4aclUdfOffsetBase4
OBJECT-TYPE
The value of offset Base.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.25INTEGER {l2(0), l3(2), l4(3)}read-writeobsolete
ipv4aclUdfOffsetByte4
OBJECT-TYPE
The value of offset Byte from base.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.26Integer32 (0..31)read-writeobsolete
ipv4aclUdfOffsetMask4
OBJECT-TYPE
The value of offset MAsk.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.27OCTET STRINGread-writeobsolete
ipv4aclProfileStatus
OBJECT-TYPE
This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.
1.3.6.1.4.1.171.10.75.16.1.15.1.1.1.28RowStatusread-createobsolete
aclProfileTable
OBJECT-TYPE
A table to ACL profile .
1.3.6.1.4.1.171.10.75.16.1.15.1.2not-accessiblecurrent
aclProfileEntry
OBJECT-TYPE
Each entry in this table is a ACL profile. Index to the table is ACL profile ID.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1not-accessiblecurrent
aclProfileNo
OBJECT-TYPE
The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.1Integer32 (1..50)read-onlycurrent
aclProfileType
OBJECT-TYPE
The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3v4 (2) - for IPv4-based rule, l3v6 (11) - for IPv6-based rule, arpSP_permit(4) - for ARP Spoofing prevention entry, arpSP_deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) - for Voice VLAN OUI entry. userDefined(9) - for User Defined entry. Note that only l2, l3 and userDefined could be set by user, other is reserved for system to show information.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.2INTEGER {l2(1), l3v4(2), impb(3), arpSP-permit(4), arpSP-deny(5), aclQos(8), userDefined(9), l3v6(11)}read-writecurrent
aclProfileRuleCount
OBJECT-TYPE
The number of rules in this profile.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.3Integer32 (0..65535)read-onlycurrent
aclProfileMask
OBJECT-TYPE
Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 ARP-SP ARP_SENDER_MAC 14 ARP-SP ARP_SENDER_IP 15 L3 TRAFFIC_CLASS 21 L3 TOS 16 UDF UDF1 17 UDF UDF2 18 UDF UDF3 19 UDF UDF4 20 L3v6 TRAFFIC_CLASS 21 L3v6 DST_IPV6 22 L3v6 SRC_IPV6 23 (MSB) ------------------------------------------- The value is in Hex format.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.4OCTET STRINGread-writecurrent
aclProfileDstMacAddrMask
OBJECT-TYPE
The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.5MacAddressread-writecurrent
aclProfileSrcMacAddrMask
OBJECT-TYPE
The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.6MacAddressread-writecurrent
aclProfileIPProtocol
OBJECT-TYPE
Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.7INTEGER {none(0), icmp(1), igmp(2), tcp(6), udp(17), icmpv6(58), ipProtocolMask(256)}read-writecurrent
aclProfileIPProtocolMask
OBJECT-TYPE
The ACL Profile IP protocol mask. If aclProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.8OCTET STRINGread-writecurrent
aclProfileDstIpAddrMaskType
OBJECT-TYPE
IPv6 Address type.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.9INTEGER {iPv4(1), iPv6(2)}read-writecurrent
aclProfileDstIpAddrMask
OBJECT-TYPE
The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.10Ipv6Addressread-writecurrent
aclProfileSrcIpAddrMaskType
OBJECT-TYPE
IPv6 Address type.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.11INTEGER {iPv4(1), iPv6(2)}read-writecurrent
aclProfileSrcIpAddrMask
OBJECT-TYPE
The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.12Ipv6Addressread-writecurrent
aclProfileDstPortMask
OBJECT-TYPE
The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.13OCTET STRINGread-writecurrent
aclProfileSrcPortMask
OBJECT-TYPE
The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.14OCTET STRINGread-writecurrent
aclProfileArpSenderMacAddrMask
OBJECT-TYPE
The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.15MacAddressread-onlycurrent
aclProfileArpSenderIpAddrMask
OBJECT-TYPE
The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.16Ipv6Addressread-onlycurrent
aclProfileUdfOffsetMap
OBJECT-TYPE
Indicate which Udf field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ UDF Offset1 0 (LSB) UDF Offset2 1 UDF Offset3 2 UDF Offset4 3 ------------------------------------------- The value is in Hex format.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.17OCTET STRINGread-writecurrent
aclUdfOffsetBase1
OBJECT-TYPE
The value of offset Base.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.18INTEGER {l2(0), l3(2), l4(3)}read-writecurrent
aclUdfOffsetByte1
OBJECT-TYPE
The value of offset Byte from base.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.19Integer32 (0..31)read-writecurrent
aclUdfOffsetMask1
OBJECT-TYPE
The value of offset MAsk.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.20OCTET STRINGread-writecurrent
aclUdfOffsetBase2
OBJECT-TYPE
The value of offset Base.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.21INTEGER {l2(0), l3(2), l4(3)}read-writecurrent
aclUdfOffsetByte2
OBJECT-TYPE
The value of offset Byte from base.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.22Integer32 (0..31)read-writecurrent
aclUdfOffsetMask2
OBJECT-TYPE
The value of offset MAsk.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.23OCTET STRINGread-writecurrent
aclUdfOffsetBase3
OBJECT-TYPE
The value of offset Base.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.24INTEGER {l2(0), l3(2), l4(3)}read-writecurrent
aclUdfOffsetByte3
OBJECT-TYPE
The value of offset Byte from base.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.25Integer32 (0..31)read-writecurrent
aclUdfOffsetMask3
OBJECT-TYPE
The value of offset MAsk.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.26OCTET STRINGread-writecurrent
aclUdfOffsetBase4
OBJECT-TYPE
The value of offset Base.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.27INTEGER {l2(0), l3(2), l4(3)}read-writecurrent
aclUdfOffsetByte4
OBJECT-TYPE
The value of offset Byte from base.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.28Integer32 (0..31)read-writecurrent
aclUdfOffsetMask4
OBJECT-TYPE
The value of offset MAsk.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.29OCTET STRINGread-writecurrent
aclProfileStatus
OBJECT-TYPE
This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of aclProfileType, aclProfileMask and ProtocolType are not conflicted.
1.3.6.1.4.1.171.10.75.16.1.15.1.2.1.30RowStatusread-createcurrent
aclL2Rule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.15.2
aclL2RuleTable
OBJECT-TYPE
A table to configure L2 filter rules in the system.
1.3.6.1.4.1.171.10.75.16.1.15.2.1not-accessiblecurrent
aclL2RuleEntry
OBJECT-TYPE
Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1not-accessiblecurrent
aclL2AccessID
OBJECT-TYPE
L2 Filter rule ID. 0 means auto assign.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.1Integer32 (0..250)read-onlycurrent
aclL2ProfileID
OBJECT-TYPE
ACL Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.2Integer32 (1..50)read-onlycurrent
aclL2RuleEtherType
OBJECT-TYPE
The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.3Integer32 (-1 | 1501..65535)read-writecurrent
aclL2RuleDstMacAddr
OBJECT-TYPE
Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.4MacAddressread-writecurrent
aclL2RuleSrcMacAddr
OBJECT-TYPE
Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.5MacAddressread-writecurrent
aclL2RuleVlanId
OBJECT-TYPE
Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.6Integer32 (-1..4094)read-writecurrent
aclL2Rule1pPriority
OBJECT-TYPE
802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.7Integer32 (-1..7)read-writecurrent
aclL2RuleDstMacAddrMask
OBJECT-TYPE
The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.8MacAddressread-onlycurrent
aclL2RuleSrcMacAddrMask
OBJECT-TYPE
The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.9MacAddressread-onlycurrent
aclL2RuleInPortList
OBJECT-TYPE
Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.10PortListread-writecurrent
aclL2RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.11INTEGER {allow(1), drop(2), mirror(3), replaceDSCP(5), replace1P(6), replaceQueue(7)}read-writecurrent
aclL2RuleRateLimit
OBJECT-TYPE
Rate limit for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.12Unsigned32read-writecurrent
aclL2RuleReplaceDSCP
OBJECT-TYPE
Replace DSCP for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.13Integer32 (-1..63)read-writecurrent
aclL2RuleReplace1P
OBJECT-TYPE
Replace DSCP for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.14Integer32 (-1..7)read-writecurrent
aclL2RuleReplaceQueue
OBJECT-TYPE
ACL L2 Rule Replace Queue.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.15Integer32read-writecurrent
aclL2RuleFilterTimeRange
OBJECT-TYPE
ACL L2 Filter Time Range
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.16OCTET STRINGread-createcurrent
aclL2RuleVlanIdMask
OBJECT-TYPE
Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.17OCTET STRINGread-writecurrent
aclL2RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.15.2.1.1.99RowStatusread-createcurrent
aclL3Rule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.15.3
aclL3RuleTable
OBJECT-TYPE
A table to configure L3 filter rules in the system.
1.3.6.1.4.1.171.10.75.16.1.15.3.1not-accessiblecurrent
aclL3RuleEntry
OBJECT-TYPE
Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1not-accessiblecurrent
aclL3RuleAccessID
OBJECT-TYPE
L3 Filter rule ID. 0 means auto assign.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.1Integer32 (0..250)read-onlycurrent
aclL3RuleProfileNo
OBJECT-TYPE
The Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.2Integer32 (1..50)read-onlycurrent
aclL3RuleProtocol
OBJECT-TYPE
The type of protocol to be checked against the packet.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.3INTEGER {icmp(1), igmp(2), tcp(6), udp(17)}read-writecurrent
aclL3RuleProtocolMask
OBJECT-TYPE
The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.4OCTET STRINGread-onlycurrent
aclL3RuleICMPMessageType
OBJECT-TYPE
The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.5Integer32 (-1..255)read-writecurrent
aclL3RuleICMPMessageCode
OBJECT-TYPE
The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.6Integer32 (-1..255)read-writecurrent
aclL3RuleDstIpAddr
OBJECT-TYPE
Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.7IpAddressread-writecurrent
aclL3RuleSrcIpAddr
OBJECT-TYPE
Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.8IpAddressread-writecurrent
aclL3RuleDstIpAddrMask
OBJECT-TYPE
The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.9IpAddressread-onlycurrent
aclL3RuleSrcIpAddrMask
OBJECT-TYPE
The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.10IpAddressread-onlycurrent
aclL3RuleTcpUdpDstPort
OBJECT-TYPE
The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.11Integer32 (-1..65535)read-writecurrent
aclL3RuleTcpUdpSrcPort
OBJECT-TYPE
The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.12Integer32 (-1..65535)read-writecurrent
aclL3RuleTcpUdpDstPortMask
OBJECT-TYPE
The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.13OCTET STRINGread-onlycurrent
aclL3RuleTcpUdpSrcPortMask
OBJECT-TYPE
The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.14OCTET STRINGread-onlycurrent
aclL3RuleTcpAckBit
OBJECT-TYPE
The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.15INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpRstBit
OBJECT-TYPE
The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.16INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpUrgBit
OBJECT-TYPE
The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.17INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpPshBit
OBJECT-TYPE
The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.18INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpSynBit
OBJECT-TYPE
The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.19INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleTcpFinBit
OBJECT-TYPE
The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.20INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclL3RuleDscp
OBJECT-TYPE
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.21Integer32 (-1..63)read-createcurrent
aclL3RuleTos
OBJECT-TYPE
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.22Integer32 (-1..7)read-createcurrent
aclL3RuleIgmpType
OBJECT-TYPE
The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.23Integer32 (-1..255)read-writecurrent
aclL3RulePortList
OBJECT-TYPE
Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.24PortListread-writecurrent
aclL3RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.25INTEGER {allow(1), drop(2), mirror(3), replaceDSCP(5), replace1P(6), replaceQueue(7)}read-writecurrent
aclL3RuleRateLimit
OBJECT-TYPE
Rate limit for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.26Unsigned32read-writecurrent
aclL3RuleReplaceDSCP
OBJECT-TYPE
ReplaceDSCP for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.27Integer32 (-1..63)read-writecurrent
aclL3RuleReplace1P
OBJECT-TYPE
ReplaceDSCP for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.28Integer32 (-1..7)read-writecurrent
aclL3RuleReplaceQueue
OBJECT-TYPE
Acl L3 Rule Replace Queue.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.29Integer32read-writecurrent
aclL3RuleFilterTimeRange
OBJECT-TYPE
ACL L3 Filter Time Range
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.30OCTET STRINGread-createcurrent
aclL3RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.15.3.1.1.99RowStatusread-createcurrent
aclv6L3RuleTable
OBJECT-TYPE
A table to configure L3 filter rules in the system.
1.3.6.1.4.1.171.10.75.16.1.15.3.2not-accessiblecurrent
aclv6L3RuleEntry
OBJECT-TYPE
Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1not-accessiblecurrent
aclv6L3RuleAccessID
OBJECT-TYPE
L3 Filter rule ID. 0 means auto assign.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.1Integer32 (0..250)read-onlycurrent
aclv6L3RuleProfileNo
OBJECT-TYPE
The Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.2Integer32 (1..50)read-onlycurrent
aclv6L3RuleProtocol
OBJECT-TYPE
The type of protocol to be checked against the packet.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.3INTEGER {tcp(6), udp(17), icmpv6(58)}read-writecurrent
aclv6L3RuleProtocolMask
OBJECT-TYPE
The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,aclL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.4OCTET STRINGread-onlycurrent
aclv6L3RuleICMPMessageType
OBJECT-TYPE
The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.5Integer32 (-1..255)read-writecurrent
aclv6L3RuleICMPMessageCode
OBJECT-TYPE
The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.6Integer32 (-1..255)read-writecurrent
aclv6L3RuleDstIpAddr
OBJECT-TYPE
Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.7Ipv6Addressread-writecurrent
aclv6L3RuleSrcIpAddr
OBJECT-TYPE
Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.8Ipv6Addressread-writecurrent
aclv6L3RuleDstIpAddrMask
OBJECT-TYPE
The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.9Ipv6Addressread-onlycurrent
aclv6L3RuleSrcIpAddrMask
OBJECT-TYPE
The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.10Ipv6Addressread-onlycurrent
aclv6L3RuleTcpUdpDstPort
OBJECT-TYPE
The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.11Integer32 (-1..65535)read-writecurrent
aclv6L3RuleTcpUdpSrcPort
OBJECT-TYPE
The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.12Integer32 (-1..65535)read-writecurrent
aclv6L3RuleTcpUdpDstPortMask
OBJECT-TYPE
The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.13OCTET STRINGread-onlycurrent
aclv6L3RuleTcpUdpSrcPortMask
OBJECT-TYPE
The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.14OCTET STRINGread-onlycurrent
aclv6L3RuleTcpAckBit
OBJECT-TYPE
The TCP ACK bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.15INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpRstBit
OBJECT-TYPE
The TCP RST bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.16INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpUrgBit
OBJECT-TYPE
The TCP Urg bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.17INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpPshBit
OBJECT-TYPE
The TCP Psh bit to be checked against the packet. The default value is 'dont_care'(-1). which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.18INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpSynBit
OBJECT-TYPE
The TCP Syn bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.19INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTcpFinBit
OBJECT-TYPE
The TCP Fin bit to be checked against the packet. The default value is 'dont_care'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.20INTEGER {dont-care(-1), establish(1), notEstablish(2)}read-createcurrent
aclv6L3RuleTrafficClass
OBJECT-TYPE
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.21Integer32 (-1..63)read-createcurrent
aclv6L3RulePortList
OBJECT-TYPE
Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.23PortListread-writecurrent
aclv6L3RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.24INTEGER {allow(1), drop(2), mirror(3), replaceDSCP(5), replace1P(6), replaceQueue(7)}read-writecurrent
aclv6L3RuleRateLimit
OBJECT-TYPE
Rate limit for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.25Unsigned32read-writecurrent
aclv6L3RuleReplaceDSCP
OBJECT-TYPE
Replace DSCP for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.26Integer32 (-1..63)read-writecurrent
aclv6L3RuleReplace1P
OBJECT-TYPE
Replace DSCP for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.27Integer32 (-1..7)read-writecurrent
aclv6L3RuleReplaceQueue
OBJECT-TYPE
Acl IPV6 L3 Rule Replace Queue.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.28Integer32read-writecurrent
aclv6L3RuleFilterTimeRange
OBJECT-TYPE
ACL IPV6 L3 Filter Time Range
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.29OCTET STRINGread-createcurrent
aclv6L3RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.15.3.2.1.99RowStatusread-createcurrent
aclPacketRule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.15.4
aclPacketRuleTable
OBJECT-TYPE
A table to configure Packet Content filter rules in the system.
1.3.6.1.4.1.171.10.75.16.1.15.4.1not-accessiblecurrent
aclPacketRuleEntry
OBJECT-TYPE
Each entry in this table is a Packet filter rule. Index to the table is the Packet filter number and Profile ID.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1not-accessiblecurrent
aclPacketAccessID
OBJECT-TYPE
Packet Filter rule ID. 0 means auto assign.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.1Integer32 (0..250)read-onlycurrent
aclPacketProfileID
OBJECT-TYPE
ACL Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.2Integer32 (1..50)read-onlycurrent
aclPacketRuleOffsetValue1
OBJECT-TYPE
The filter value of Offset 1.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.3OCTET STRINGread-writecurrent
aclPacketRuleOffsetValue2
OBJECT-TYPE
The filter value of Offset 2.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.4OCTET STRINGread-writecurrent
aclPacketRuleOffsetValue3
OBJECT-TYPE
The filter value of Offset 3.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.5OCTET STRINGread-writecurrent
aclPacketRuleOffsetValue4
OBJECT-TYPE
The filter value of Offset 4.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.6OCTET STRINGread-writecurrent
aclPacketRuleInPortList
OBJECT-TYPE
Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.7PortListread-writecurrent
aclPacketRuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.8INTEGER {allow(1), drop(2), mirror(3), replaceDSCP(5), replace1P(6), replaceQueue(7)}read-writecurrent
aclPacketRuleRateLimit
OBJECT-TYPE
Rate limit for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.9Unsigned32read-writecurrent
aclPacketRuleReplaceDSCP
OBJECT-TYPE
Replace DSCP for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.10Integer32 (-1..63)read-writecurrent
aclPacketRuleReplace1P
OBJECT-TYPE
Replace 1p for matched packet.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.11Integer32 (-1..7)read-writecurrent
aclPacketRuleReplaceQueue
OBJECT-TYPE
Acl Rule Replace Queue.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.12Integer32read-writecurrent
aclPacketRuleFilterTimeRange
OBJECT-TYPE
Acl Filter Time Range
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.13OCTET STRINGread-createcurrent
aclPacketRuleOffsetValue1Mask
OBJECT-TYPE
The filter Mask of Offset 1.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.14OCTET STRINGread-writecurrent
aclPacketRuleOffsetValue2Mask
OBJECT-TYPE
The filter Mask of Offset 2.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.15OCTET STRINGread-writecurrent
aclPacketRuleOffsetValue3Mask
OBJECT-TYPE
The filter Mask of Offset 3.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.16OCTET STRINGread-writecurrent
aclPacketRuleOffsetValue4Mask
OBJECT-TYPE
The filter Mask of Offset 4.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.17OCTET STRINGread-writecurrent
aclPacketRuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.15.4.1.1.99RowStatusread-createcurrent
aclFlowMeterRule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.15.10
aclFlowMeterTable
OBJECT-TYPE
A table to configure L2 filter rules in the system.
1.3.6.1.4.1.171.10.75.16.1.15.10.1not-accessiblecurrent
aclFlowMeterEntry
OBJECT-TYPE
Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.
1.3.6.1.4.1.171.10.75.16.1.15.10.1.1not-accessiblecurrent
aclFlowMeterProfileID
OBJECT-TYPE
ACL Profile ID which this flow meter join.
1.3.6.1.4.1.171.10.75.16.1.15.10.1.1.1Integer32 (1..50)read-onlycurrent
aclFlowMeterAccessID
OBJECT-TYPE
ACL Access ID which this flow meter join.
1.3.6.1.4.1.171.10.75.16.1.15.10.1.1.2Integer32 (1..250)read-onlycurrent
aclFlowMeterRate
OBJECT-TYPE
The rate limiter of meter.
1.3.6.1.4.1.171.10.75.16.1.15.10.1.1.3Integer32 (64..1024000)read-writecurrent
aclFlowMeterBurstSize
OBJECT-TYPE
The burst size of meter.
1.3.6.1.4.1.171.10.75.16.1.15.10.1.1.4Integer32 (0..1016)read-writecurrent
aclFlowMeterReplaceDscp
OBJECT-TYPE
Replace DSCP for matched out-band packets when aclFlowMeterAction is replace DSCP.
1.3.6.1.4.1.171.10.75.16.1.15.10.1.1.5Integer32 (0..63)read-writecurrent
aclFlowMeterAction
OBJECT-TYPE
Specifies the action to be taken on the out-band packet if the filter rule matches. If the action is 'drop', the packet will be discarded.
1.3.6.1.4.1.171.10.75.16.1.15.10.1.1.6INTEGER {drop(2), replaceDSCP(5)}read-writecurrent
aclFlowMeterStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.15.10.1.1.99RowStatusread-createcurrent
companySyslog
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.16
syslogSettingGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.16.1
syslogEnable
OBJECT-TYPE
This object is for enabling or disabling syslog alert features in the system and the syslog will save to flash or send to remote syslog server. System Logs record and manage events, as well as report errors and informational messages.
1.3.6.1.4.1.171.10.75.16.1.16.1.1INTEGER {disable(0), enable(1)}read-writecurrent
syslogSaveMode
OBJECT-TYPE
This object is for choosing the method to save syslog into flash.
1.3.6.1.4.1.171.10.75.16.1.16.1.2INTEGER {onDemand(0), timeInterval(1), logTrigger(2)}read-writecurrent
syslogSaveMinutes
OBJECT-TYPE
When savemode is time interval, it's used to set the interval minutes of system save syslog to flash.
1.3.6.1.4.1.171.10.75.16.1.16.1.3INTEGER (1..65535)read-writecurrent
ipv4syslogServerGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.16.2
ipv4syslogServTable
OBJECT-TYPE
The table of syslog remote server.
1.3.6.1.4.1.171.10.75.16.1.16.2.1not-accessiblecurrent
ipv4syslogServEntry
OBJECT-TYPE
The list of syslog remote server entry.
1.3.6.1.4.1.171.10.75.16.1.16.2.1.1not-accessiblecurrent
ipv4syslogServIndex
OBJECT-TYPE
The index of syslog remote server.
1.3.6.1.4.1.171.10.75.16.1.16.2.1.1.1INTEGER (1..4)read-onlycurrent
ipv4syslogServAddr
OBJECT-TYPE
The IP Address of syslog remote server.
1.3.6.1.4.1.171.10.75.16.1.16.2.1.1.2IpAddressread-createcurrent
ipv4syslogServSeverity
OBJECT-TYPE
Specifies the log level option to be set for a specific server.
1.3.6.1.4.1.171.10.75.16.1.16.2.1.1.3INTEGER {warning(4), information(6), all(7)}read-createcurrent
ipv4syslogServFacility
OBJECT-TYPE
The Syslog standard facilities. The facility to be used when sending Syslog messages to this server.
1.3.6.1.4.1.171.10.75.16.1.16.2.1.1.4INTEGER {local0(128), local1(136), local2(144), local3(152), local4(160), local5(168), local6(176), local7(184)}read-createcurrent
ipv4syslogServUDPport
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.16.2.1.1.5INTEGER (514 | 6000..65535)read-createcurrent
ipv4syslogServSrvStatus
OBJECT-TYPE
The status for this server. If enable, system will send message to this server.
1.3.6.1.4.1.171.10.75.16.1.16.2.1.1.6INTEGER {disabled(0), enabled(1)}read-createcurrent
ipv4syslogServSrvRowStatus
OBJECT-TYPE
Row status of this server entry.
1.3.6.1.4.1.171.10.75.16.1.16.2.1.1.7RowStatusread-writecurrent
syslogServerGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.16.3
syslogServTable
OBJECT-TYPE
The table of syslog remote server.
1.3.6.1.4.1.171.10.75.16.1.16.3.1not-accessiblecurrent
syslogServEntry
OBJECT-TYPE
The list of syslog remote server entry.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1not-accessiblecurrent
syslogServIndex
OBJECT-TYPE
The index of syslog remote server.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.1INTEGER (1..4)read-onlycurrent
syslogServAddrType
OBJECT-TYPE
Specifies the Address type of server.Address type shall be ipv4 or ipv6.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.2INTEGER {ipv4(1), ipv6(2)}read-createcurrent
syslogServAddr
OBJECT-TYPE
Specifies the ServerIP to which the syslog shall be forwarded.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.3Ipv6Addressread-createcurrent
syslogServInterfaceName
OBJECT-TYPE
Specifies the interface name when the syslogServInterfaceName is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.4OCTET STRINGread-createcurrent
syslogServSeverity
OBJECT-TYPE
Specifies the log level option to be set for a specific server.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.5INTEGER {warning(4), information(6), all(7)}read-createcurrent
syslogServFacility
OBJECT-TYPE
The Syslog standard facilities. The facility to be used when sending Syslog messages to this server.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.6INTEGER {local0(128), local1(136), local2(144), local3(152), local4(160), local5(168), local6(176), local7(184)}read-createcurrent
syslogServUDPport
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.7INTEGER (514 | 6000..65535)read-createcurrent
syslogServSrvStatus
OBJECT-TYPE
The status for this server. If enable, system will send message to this server.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.8INTEGER {disabled(0), enabled(1)}read-writecurrent
syslogServSrvRowStatus
OBJECT-TYPE
Row status of this server entry.
1.3.6.1.4.1.171.10.75.16.1.16.3.1.1.9RowStatusread-writecurrent
companyLBD
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.17
sysLBDStateEnable
OBJECT-TYPE
Enable/Disable Loopback detection function. The Loopback Detection function is used to detect the loop created by a specific port while Spanning Tree Protocol (STP) is not enabled in the network, especially when the down links are hubs or unmanaged switchs.The Switch will automatically shutdown the port and sends a log to the administrator.
1.3.6.1.4.1.171.10.75.16.1.17.1INTEGER {enabled(1), disabled(2)}read-writecurrent
sysLBDMode
OBJECT-TYPE
Loopback detection function mode.
1.3.6.1.4.1.171.10.75.16.1.17.2INTEGER {port(1), vlan(2)}read-writecurrent
sysLBDInterval
OBJECT-TYPE
Set a Loop detection Interval between 1 and 32767 seconds. The default is 2 seconds. This time interval to be used at counting time seconds to resend the CTP packet automatically.
1.3.6.1.4.1.171.10.75.16.1.17.3Integer32 (1..32767)read-writecurrent
sysLBDRecoverTime
OBJECT-TYPE
This time interval to be used at counting time seconds to recover the disabled port automatically. The Loop Detection Recover Time can be set at 0 seconds, or 60 to 1000000 seconds. Entering 0 will disable the Loop Detection Recover Time. The default is 60 seconds.
1.3.6.1.4.1.171.10.75.16.1.17.4Integer32 (0 | 60..1000000)read-writecurrent
sysLBDCtrlTable
OBJECT-TYPE
A table to control Loopback detection features either for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.16.1.17.5not-accessiblecurrent
sysLBDCtrlEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.17.5.1not-accessiblecurrent
sysLBDCtrlIndex
OBJECT-TYPE
The interface index of the port for which the configuration in this entry applies. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.17.5.1.1Integer32 (1..26)read-onlycurrent
sysLBDPortStatus
OBJECT-TYPE
Provides control to per port enable or disable the loopback detection function. Default is disabled.
1.3.6.1.4.1.171.10.75.16.1.17.5.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
sysLBDPortLoopStatus
OBJECT-TYPE
The loop status for this port.
1.3.6.1.4.1.171.10.75.16.1.17.5.1.3INTEGER {normal(1), loop(2)}read-onlycurrent
sysLBDVlanLoopTable
OBJECT-TYPE
A table to display Loopback detection features by vlan mode .
1.3.6.1.4.1.171.10.75.16.1.17.6not-accessiblecurrent
sysLBDVlanLoopEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.17.6.1not-accessiblecurrent
sysLBDVlanLoopIndex
OBJECT-TYPE
Display port lists loop status by vlan.
1.3.6.1.4.1.171.10.75.16.1.17.6.1.1Integer32 (1..4094)read-onlycurrent
sysLBDVlanLoopPorts
OBJECT-TYPE
Display port lists loop status by vlan.
1.3.6.1.4.1.171.10.75.16.1.17.6.1.2PortListread-onlycurrent
companyMirror
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.18
sysMirrorStatus
OBJECT-TYPE
Enable/Disable Port Mirroring function. Default is disabled. Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another port where the packet can be studied.
1.3.6.1.4.1.171.10.75.16.1.18.1INTEGER {enabled(1), disabled(2)}read-writecurrent
sysMirrorTargetPort
OBJECT-TYPE
Specifies the port to which the mirrored traffic in the system is to be copied.
1.3.6.1.4.1.171.10.75.16.1.18.2Integer32read-writecurrent
sysMirrorCtrlIngressMirroring
OBJECT-TYPE
Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.
1.3.6.1.4.1.171.10.75.16.1.18.3PortListread-writecurrent
sysMirrorCtrlEgressMirroring
OBJECT-TYPE
Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.
1.3.6.1.4.1.171.10.75.16.1.18.4PortListread-writecurrent
companyStaticMcast
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.19
staticMcastTable
OBJECT-TYPE
A list of the Static MACs
1.3.6.1.4.1.171.10.75.16.1.19.1not-accessiblecurrent
staticMcastEntry
OBJECT-TYPE
A Static MAC entry containing the mac and forwarding port.
1.3.6.1.4.1.171.10.75.16.1.19.1.1not-accessiblecurrent
staticMcastVlanID
OBJECT-TYPE
The VLAN ID of the static MAC entry.
1.3.6.1.4.1.171.10.75.16.1.19.1.1.1INTEGER (1..4094)read-onlycurrent
staticMcastMac
OBJECT-TYPE
The MAC address associated of the static MAC entry.
1.3.6.1.4.1.171.10.75.16.1.19.1.1.2MacAddressread-onlycurrent
staticMcastEgressPorts
OBJECT-TYPE
The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast MAC address must be forwarded, regardless of any dynamic information e.g. from GMRP. A port may not be added in this set if it is already a member of the set of ports in dot1qStaticMulticastForbiddenEgressPorts. The default value of this object is a string of ones of appropriate length.
1.3.6.1.4.1.171.10.75.16.1.19.1.1.3PortList (SIZE(1..26))read-onlycurrent
staticMcastIpAddr
OBJECT-TYPE
Static Multicast IP Address.
1.3.6.1.4.1.171.10.75.16.1.19.1.1.4IpAddressread-onlycurrent
staticMcastStatus
OBJECT-TYPE
The status of an entry in the Static Mcast Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.19.1.1.5RowStatusread-writecurrent
companySNTPSetting
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.20
ipv4sysSNTPTimeSeconds
OBJECT-TYPE
This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037).
1.3.6.1.4.1.171.10.75.16.1.20.1Integer32read-writeobsolete
ipv4sysSNTPFirstServer
OBJECT-TYPE
SNTP First Server's IP Address
1.3.6.1.4.1.171.10.75.16.1.20.2IpAddressread-writeobsolete
ipv4sysSNTPSecondServer
OBJECT-TYPE
SNTP Second Server's IP Address
1.3.6.1.4.1.171.10.75.16.1.20.3IpAddressread-writeobsolete
ipv4sysSNTPPollInterval
OBJECT-TYPE
SNTP Poll Interval In Seconds (30-99999)
1.3.6.1.4.1.171.10.75.16.1.20.4Integer32read-writeobsolete
ipv4sysSNTPState
OBJECT-TYPE
Enable/Disable SNTP function in the system.
1.3.6.1.4.1.171.10.75.16.1.20.5INTEGER {sntp(1), local(2)}read-writeobsolete
ipv4sysSNTPDSTOffset
OBJECT-TYPE
This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes.
1.3.6.1.4.1.171.10.75.16.1.20.6INTEGER {offset30min(30), offset60min(60), offset90min(90), offset120min(120)}read-writeobsolete
ipv4sysSNTPGMTMinutes
OBJECT-TYPE
Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)
1.3.6.1.4.1.171.10.75.16.1.20.7INTEGERread-writeobsolete
ipv4sysSNTPDSTStartMon
OBJECT-TYPE
The start month of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.8INTEGERread-writeobsolete
ipv4sysSNTPDSTStartDay
OBJECT-TYPE
The start day of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.9INTEGERread-writeobsolete
ipv4sysSNTPDSTStartHour
OBJECT-TYPE
The start hour of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.10INTEGERread-writeobsolete
ipv4sysSNTPDSTStartMin
OBJECT-TYPE
The start minute of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.11INTEGERread-writeobsolete
ipv4sysSNTPDSTEndMon
OBJECT-TYPE
The end month of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.12INTEGERread-writeobsolete
ipv4sysSNTPDSTEndDay
OBJECT-TYPE
The end day of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.13INTEGERread-writeobsolete
ipv4sysSNTPDSTEndHour
OBJECT-TYPE
The end hour of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.14INTEGERread-writeobsolete
ipv4sysSNTPDSTEndMin
OBJECT-TYPE
The end minute of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.15INTEGERread-writeobsolete
ipv4sysSNTPDSTState
OBJECT-TYPE
This object is for Annual(1) or Disabled(2) DST state in the system.
1.3.6.1.4.1.171.10.75.16.1.20.16INTEGER {annual(1), disabled(2)}read-writeobsolete
sysSNTPServerTable
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.20.17
sysSNTPTimeSeconds
OBJECT-TYPE
This object is for setting the system time in seconds from Epoch (00:00:00 UTC, January 1, 2009). Notice : input value must larger than 1230768000 (00:00:00 UTC, January 1, 2009) and smaller than 2145916799 (23:59:59 UTC, December 31, 2037).
1.3.6.1.4.1.171.10.75.16.1.20.17.1Integer32read-writecurrent
sysSNTPFirstServer
OBJECT-TYPE
SNTP First Server's IPv6 Address
1.3.6.1.4.1.171.10.75.16.1.20.17.2Ipv6Addressread-writecurrent
sysSNTPFirstType
OBJECT-TYPE
SNTP First Server's IPv6 Address type.
1.3.6.1.4.1.171.10.75.16.1.20.17.3INTEGER {iPv4(1), iPv6(2)}read-writecurrent
sysSNTPFirstInterfaceName
OBJECT-TYPE
Specifies the interface name when the sysSNTPFirstServer is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.20.17.4OCTET STRINGread-writecurrent
sysSNTPSecondServer
OBJECT-TYPE
SNTP Second Server's IPv6 Address
1.3.6.1.4.1.171.10.75.16.1.20.17.5Ipv6Addressread-writecurrent
sysSNTPSecondType
OBJECT-TYPE
SNTP First Server's IPv6 Address type.
1.3.6.1.4.1.171.10.75.16.1.20.17.6INTEGER {iPv4(1), iPv6(2)}read-writecurrent
sysSNTPSecondInterfaceName
OBJECT-TYPE
Specifies the interface name when the sysSNTPSecondServer is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.20.17.7OCTET STRINGread-writecurrent
sysSNTPPollInterval
OBJECT-TYPE
SNTP Poll Interval In Seconds (30-99999)
1.3.6.1.4.1.171.10.75.16.1.20.17.8Integer32read-writecurrent
sysSNTPState
OBJECT-TYPE
Enable/Disable SNTP function in the system.
1.3.6.1.4.1.171.10.75.16.1.20.17.9INTEGER {sntp(1), local(2)}read-writecurrent
sysSNTPDSTOffset
OBJECT-TYPE
This object is for Daylight Saving Time Offset In (30/60/90/120) Minutes.
1.3.6.1.4.1.171.10.75.16.1.20.17.10INTEGER {offset30min(30), offset60min(60), offset90min(90), offset120min(120)}read-writecurrent
sysSNTPGMTMinutes
OBJECT-TYPE
Specifies the Time Zone Offset from GMT in +/- Minutes. (+780 ~ -720)
1.3.6.1.4.1.171.10.75.16.1.20.17.11INTEGERread-writecurrent
sysSNTPDSTStartMon
OBJECT-TYPE
The start month of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.17.12INTEGERread-writecurrent
sysSNTPDSTStartDay
OBJECT-TYPE
The start day of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.17.13INTEGERread-writecurrent
sysSNTPDSTStartHour
OBJECT-TYPE
The start hour of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.17.14INTEGERread-writecurrent
sysSNTPDSTStartMin
OBJECT-TYPE
The start minute of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.17.15INTEGERread-writecurrent
sysSNTPDSTEndMon
OBJECT-TYPE
The end month of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.17.16INTEGERread-writecurrent
sysSNTPDSTEndDay
OBJECT-TYPE
The end day of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.17.17INTEGERread-writecurrent
sysSNTPDSTEndHour
OBJECT-TYPE
The end hour of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.17.18INTEGERread-writecurrent
sysSNTPDSTEndMin
OBJECT-TYPE
The end minute of Daylight Saving Time.
1.3.6.1.4.1.171.10.75.16.1.20.17.19INTEGERread-writecurrent
sysSNTPDSTState
OBJECT-TYPE
This object is for Enabled(1) or Disabled(2) DST state in the system.
1.3.6.1.4.1.171.10.75.16.1.20.17.20INTEGER {enabled(1), disabled(2)}read-writecurrent
sysSNTPDSTMethod
OBJECT-TYPE
This object is for Annual(1) or Repeating(2) DST method in the system.
1.3.6.1.4.1.171.10.75.16.1.20.17.30INTEGER {annual(1), repeating(2)}read-writecurrent
sysSNTPDSTRepeatStartMon
OBJECT-TYPE
The start month of Daylight Saving Time in Repeating mode.
1.3.6.1.4.1.171.10.75.16.1.20.17.31INTEGERread-writecurrent
sysSNTPDSTRepeatStartWeek
OBJECT-TYPE
The start week of Daylight Saving Time in Repeating mode.
1.3.6.1.4.1.171.10.75.16.1.20.17.32INTEGER {last(0), first(1), second(2), third(3), fourth(4), fifth(5)}read-writecurrent
sysSNTPDSTRepeatStartWeekDay
OBJECT-TYPE
The start weekday of Daylight Saving Time in Repeating mode.
1.3.6.1.4.1.171.10.75.16.1.20.17.33INTEGER {sun(0), mon(1), tue(2), wed(3), thu(4), fri(5), sat(6)}read-writecurrent
sysSNTPDSTRepeatStartHour
OBJECT-TYPE
The start hour of Daylight Saving Time in Repeating mode..
1.3.6.1.4.1.171.10.75.16.1.20.17.34INTEGERread-writecurrent
sysSNTPDSTRepeatStartMin
OBJECT-TYPE
The start minute of Daylight Saving Time in Repeating mode.
1.3.6.1.4.1.171.10.75.16.1.20.17.35INTEGERread-writecurrent
sysSNTPDSTRepeatEndMon
OBJECT-TYPE
The end month of Daylight Saving Time in Repeating mode.
1.3.6.1.4.1.171.10.75.16.1.20.17.36INTEGERread-writecurrent
sysSNTPDSTRepeatEndWeek
OBJECT-TYPE
The end week of Daylight Saving Time in Repeating mode.
1.3.6.1.4.1.171.10.75.16.1.20.17.37INTEGER {last(0), first(1), second(2), third(3), fourth(4), fifth(5)}read-writecurrent
sysSNTPDSTRepeatEndWeekDay
OBJECT-TYPE
The end weekday of Daylight Saving Time in Repeating mode.
1.3.6.1.4.1.171.10.75.16.1.20.17.38INTEGER {sun(0), mon(1), tue(2), wed(3), thu(4), fri(5), sat(6)}read-writecurrent
sysSNTPDSTRepeatEndHour
OBJECT-TYPE
The end hour of Daylight Saving Time in Repeating mode..
1.3.6.1.4.1.171.10.75.16.1.20.17.39INTEGERread-writecurrent
sysSNTPDSTRepeatEndMin
OBJECT-TYPE
The end minute of Daylight Saving Time in Repeating mode.
1.3.6.1.4.1.171.10.75.16.1.20.17.40INTEGERread-writecurrent
companyRMON
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.22
rmonGlobalState
OBJECT-TYPE
This object is for enabling or disabling RMON function.
1.3.6.1.4.1.171.10.75.16.1.22.1INTEGER {enabled(1), disabled(2)}read-writecurrent
rmonStatistics
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.22.2
rmonStatsTable
OBJECT-TYPE
A list of Ethernet statistics entries.
1.3.6.1.4.1.171.10.75.16.1.22.2.1not-accessiblecurrent
rmonStatsEntry
OBJECT-TYPE
A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named etherStatsPkts.1
1.3.6.1.4.1.171.10.75.16.1.22.2.1.1not-accessiblecurrent
rmonStatsIndex
OBJECT-TYPE
The value of this object uniquely identifies this etherStats entry.
1.3.6.1.4.1.171.10.75.16.1.22.2.1.1.1Integer32 (1..65535)read-onlycurrent
rmonStatsDataSource
OBJECT-TYPE
This object identifies the source of the data that this etherStats entry is configured to analyze. This source can be any ethernet interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated etherStatsStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.2.1.1.2OBJECT IDENTIFIERread-createcurrent
rmonStatsOwner
OBJECT-TYPE
The entity that configured this entry and is therefore using the resources assigned to it.
1.3.6.1.4.1.171.10.75.16.1.22.2.1.1.3OwnerStringread-createcurrent
rmonStatsStatus
OBJECT-TYPE
The status of this etherStats entry.
1.3.6.1.4.1.171.10.75.16.1.22.2.1.1.4RmonStatusread-createcurrent
rmonHistory
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.22.3
rmonHistoryTable
OBJECT-TYPE
A list of history control entries.
1.3.6.1.4.1.171.10.75.16.1.22.3.1not-accessiblecurrent
rmonHistoryEntry
OBJECT-TYPE
A list of parameters that set up a periodic sampling of statistics. As an example, an instance of the historyControlInterval object might be named historyControlInterval.2
1.3.6.1.4.1.171.10.75.16.1.22.3.1.1not-accessiblecurrent
rmonHistoryIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the historyControl table. Each such entry defines a set of samples at a particular interval for an interface on the device.
1.3.6.1.4.1.171.10.75.16.1.22.3.1.1.1Integer32 (1..65535)read-onlycurrent
rmonHistoryDataSource
OBJECT-TYPE
This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this historyControlEntry. This source can be any interface on this device. In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 2233 [17], for the desired interface. For example, if an entry were to receive data from interface #1, this object would be set to ifIndex.1. The statistics in this group reflect all packets on the local network segment attached to the identified interface. An agent may or may not be able to tell if fundamental changes to the media of the interface have occurred and necessitate an invalidation of this entry. For example, a hot-pluggable ethernet card could be pulled out and replaced by a token-ring card. In such a case, if the agent has such knowledge of the change, it is recommended that it invalidate this entry. This object may not be modified if the associated historyControlStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.3.1.1.2OBJECT IDENTIFIERread-createcurrent
rmonHistoryBucketsRequested
OBJECT-TYPE
The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this historyControlEntry. When this object is created or modified, the probe should set historyControlBucketsGranted as closely to this object as is possible for the particular probe implementation and available resources.
1.3.6.1.4.1.171.10.75.16.1.22.3.1.1.3Integer32 (1..65535)read-createcurrent
rmonHistoryInterval
OBJECT-TYPE
The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this historyControlEntry. This interval can be set to any number of seconds between 1 and 3600 (1 hour). Because the counters in a bucket may overflow at their maximum value with no indication, a prudent manager will take into account the possibility of overflow in any of the associated counters. It is important to consider the minimum time in which any counter could overflow on a particular media type and set the historyControlInterval object to a value less than this interval. This is typically most important for the 'octets' counter in any media-specific table. For example, on an Ethernet network, the etherHistoryOctets counter could overflow in about one hour at the Ethernet's maximum utilization. This object may not be modified if the associated historyControlStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.3.1.1.4Integer32 (1..3600)read-createcurrent
rmonHistoryOwner
OBJECT-TYPE
The entity that configured this entry and is therefore using the resources assigned to it.
1.3.6.1.4.1.171.10.75.16.1.22.3.1.1.5OwnerStringread-createcurrent
rmonHistoryStatus
OBJECT-TYPE
The status of this historyControl entry. Each instance of the media-specific table associated with this historyControlEntry will be deleted by the agent if this historyControlEntry is not equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.3.1.1.6RmonStatusread-createcurrent
rmonAlarm
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.22.4
rmonAlarmTable
OBJECT-TYPE
A list of alarm entries.
1.3.6.1.4.1.171.10.75.16.1.22.4.1not-accessiblecurrent
rmonAlarmEntry
OBJECT-TYPE
A list of parameters that set up a periodic checking for alarm conditions. For example, an instance of the alarmValue object might be named alarmValue.8
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1not-accessiblecurrent
rmonAlarmIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the alarm table. Each such entry defines a diagnostic sample at a particular interval for an object on the device.
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.1Integer32 (1..65535)read-onlycurrent
rmonAlarmInterval
OBJECT-TYPE
The interval in seconds over which the data is sampled and compared with the rising and falling thresholds. When setting this variable, care should be taken in the case of deltaValue sampling - the interval should be set short enough that the sampled variable is very unlikely to increase or decrease by more than 2^31 - 1 during a single sampling interval. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.2Integer32read-createcurrent
rmonAlarmVariable
OBJECT-TYPE
The object identifier of the particular variable to be sampled. Only variables that resolve to an ASN.1 primitive type of INTEGER (INTEGER, Integer32, Counter32, Counter64, Gauge, or TimeTicks) may be sampled. Because SNMP access control is articulated entirely in terms of the contents of MIB views, no access control mechanism exists that can restrict the value of this object to identify only those objects that exist in a particular MIB view. Because there is thus no acceptable means of restricting the read access that could be obtained through the alarm mechanism, the probe must only grant write access to this object in those views that have read access to all objects on the probe. During a set operation, if the supplied variable name is not available in the selected MIB view, a badValue error must be returned. If at any time the variable name of an established alarmEntry is no longer available in the selected MIB view, the probe must change the status of this alarmEntry to invalid(4). This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.3OBJECT IDENTIFIERread-createcurrent
rmonAlarmSampleType
OBJECT-TYPE
The method of sampling the selected variable and calculating the value to be compared against the thresholds. If the value of this object is absoluteValue(1), the value of the selected variable will be compared directly with the thresholds at the end of the sampling interval. If the value of this object is deltaValue(2), the value of the selected variable at the last sample will be subtracted from the current value, and the difference compared with the thresholds. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.4INTEGER {absoluteValue(1), deltaValue(2)}read-createcurrent
rmonAlarmRisingThreshold
OBJECT-TYPE
A threshold for the sampled statistic. When the current sampled value is greater than or equal to this threshold, and the value at the last sampling interval was less than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is greater than or equal to this threshold and the associated alarmStartupAlarm is equal to risingAlarm(1) or risingOrFallingAlarm(3). After a rising event is generated, another such event will not be generated until the sampled value falls below this threshold and reaches the alarmFallingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.5Integer32read-createcurrent
rmonAlarmFallingThreshold
OBJECT-TYPE
A threshold for the sampled statistic. When the current sampled value is less than or equal to this threshold, and the value at the last sampling interval was greater than this threshold, a single event will be generated. A single event will also be generated if the first sample after this entry becomes valid is less than or equal to this threshold and the associated alarmStartupAlarm is equal to fallingAlarm(2) or risingOrFallingAlarm(3). After a falling event is generated, another such event will not be generated until the sampled value rises above this threshold and reaches the alarmRisingThreshold. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.6Integer32read-createcurrent
rmonAlarmRisingEventIndex
OBJECT-TYPE
The index of the eventEntry that is used when a rising threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.7Integer32 (0..65535)read-createcurrent
rmonAlarmFallingEventIndex
OBJECT-TYPE
The index of the eventEntry that is used when a falling threshold is crossed. The eventEntry identified by a particular value of this index is the same as identified by the same value of the eventIndex object. If there is no corresponding entry in the eventTable, then no association exists. In particular, if this value is zero, no associated event will be generated, as zero is not a valid event index. This object may not be modified if the associated alarmStatus object is equal to valid(1).
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.8Integer32 (0..65535)read-createcurrent
rmonAlarmOwner
OBJECT-TYPE
The entity that configured this entry and is therefore using the resources assigned to it.
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.9OwnerStringread-createcurrent
rmonAlarmStatus
OBJECT-TYPE
The status of this alarm entry.
1.3.6.1.4.1.171.10.75.16.1.22.4.1.1.10RmonStatusread-createcurrent
rmonEvent
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.22.5
rmonEventTable
OBJECT-TYPE
A list of events to be generated.
1.3.6.1.4.1.171.10.75.16.1.22.5.1not-accessiblecurrent
rmonEventEntry
OBJECT-TYPE
A set of parameters that describe an event to be generated when certain conditions are met. As an example, an instance of the eventLastTimeSent object might be named eventLastTimeSent.6
1.3.6.1.4.1.171.10.75.16.1.22.5.1.1not-accessiblecurrent
rmonEventIndex
OBJECT-TYPE
An index that uniquely identifies an entry in the event table. Each such entry defines one event that is to be generated when the appropriate conditions occur.
1.3.6.1.4.1.171.10.75.16.1.22.5.1.1.1Integer32 (1..65535)read-onlycurrent
rmonEventDescription
OBJECT-TYPE
A comment describing this event entry.
1.3.6.1.4.1.171.10.75.16.1.22.5.1.1.2DisplayString (SIZE(0..127))read-createcurrent
rmonEventType
OBJECT-TYPE
The type of notification that the probe will make about this event. In the case of log, an entry is made in the log table for each event. In the case of snmp-trap, an SNMP trap is sent to one or more management stations.
1.3.6.1.4.1.171.10.75.16.1.22.5.1.1.3INTEGER {none(1), log(2), snmptrap(3), logandtrap(4)}read-createcurrent
rmonEventCommunity
OBJECT-TYPE
If an SNMP trap is to be sent, it will be sent to the SNMP community specified by this octet string.
1.3.6.1.4.1.171.10.75.16.1.22.5.1.1.4OCTET STRING (SIZE(0..127))read-createcurrent
rmonEventOwner
OBJECT-TYPE
The entity that configured this entry and is therefore using the resources assigned to it. If this object contains a string starting with 'monitor' and has associated entries in the log table, all connected management stations should retrieve those log entries, as they may have significance to all management stations connected to this device
1.3.6.1.4.1.171.10.75.16.1.22.5.1.1.5OwnerStringread-createcurrent
rmonEventStatus
OBJECT-TYPE
The status of this event entry. If this object is not equal to valid(1), all associated log entries shall be deleted by the agent.
1.3.6.1.4.1.171.10.75.16.1.22.5.1.1.6RmonStatusread-createcurrent
companyAuthGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.23
swAuthenCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.23.1
swAuthStatus
OBJECT-TYPE
Enable/Disable Static 802.1x.
1.3.6.1.4.1.171.10.75.16.1.23.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
swAuthMode
OBJECT-TYPE
This object indicates the authentication mode of the device.
1.3.6.1.4.1.171.10.75.16.1.23.1.2INTEGER {portBase(1), macBase(2)}read-writecurrent
authProtocol
OBJECT-TYPE
The authentication method used to authenticate users.
1.3.6.1.4.1.171.10.75.16.1.23.1.3INTEGER {authProtocolRadiusEap(1), authProtocolLocal(2)}read-writecurrent
swAuthCtrlPktFwdMode
OBJECT-TYPE
When 802.1x disable, this item can decided eap packet be forward or drop.
1.3.6.1.4.1.171.10.75.16.1.23.1.4INTEGER {authForwardEap(1), authDropEap(2)}read-writecurrent
swAuthPortAccessCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.23.2
swAuthPortAccessControlTable
OBJECT-TYPE
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
1.3.6.1.4.1.171.10.75.16.1.23.2.1not-accessiblecurrent
swAuthPortAccessControlEntry
OBJECT-TYPE
The configuration information for an Authenticator Port.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1not-accessiblecurrent
swAuthAuthConfigPortNumber
OBJECT-TYPE
A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.1INTEGER (1..26)read-onlycurrent
swAuthAuthQuietPeriod
OBJECT-TYPE
The value, in seconds, of the quietPeriod constant currently in use by the Authenticator PAE state machine.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.2INTEGER (0..65535)read-writecurrent
swAuthAuthSuppTimeout
OBJECT-TYPE
The value, in seconds, of the suppTimeout constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.3INTEGER (1..65535)read-writecurrent
swAuthAuthServerTimeout
OBJECT-TYPE
The value, in seconds, of the serverTimeout constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.4INTEGER (1..65535)read-writecurrent
swAuthAuthMaxReq
OBJECT-TYPE
The value of the maxReq constant currently in use by the Backend Authentication state machine.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.5INTEGER (1..10)read-writecurrent
swAuthAuthTxPeriod
OBJECT-TYPE
The value, in seconds, of the txPeriod constant currently in use by the Authenticator PAE state machine.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.6INTEGER (1..65535)read-writecurrent
swAuthAuthReAuthPeriod
OBJECT-TYPE
The value, in seconds, of the reAuthPeriod constant currently in use by the Reauthentication Timer state machine.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.7INTEGER (1..65535)read-writecurrent
swAuthAuthReAuthentication
OBJECT-TYPE
The enable/disable control used by the Reauthentication Timer state machine (8.5.5.1).
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
swAuthAuthConfigPortControl
OBJECT-TYPE
The current value of the controlled Port control parameter for the Port.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.9INTEGER {forceUnauthorized(1), auto(2), forceAuthorized(3)}read-writecurrent
swAuthAuthCapability
OBJECT-TYPE
The current value of the controlled Port control parameter for the Port.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.10INTEGER {authenticator(1), none(2)}read-writecurrent
swAuthAuthDirection
OBJECT-TYPE
The current value of the controlled Port control parameter for the Port.
1.3.6.1.4.1.171.10.75.16.1.23.2.1.1.11INTEGER {both(0), in(1)}read-writecurrent
swAuthUser
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.23.3
swAuthUserTable
OBJECT-TYPE
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
1.3.6.1.4.1.171.10.75.16.1.23.3.1not-accessiblecurrent
swAuthUserEntry
OBJECT-TYPE
The configuration information for an Authenticator Port.
1.3.6.1.4.1.171.10.75.16.1.23.3.1.1not-accessiblecurrent
swAuthUserName
OBJECT-TYPE
The unique index value of a row in this table. This object is used to set 802.1X Local user name, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.
1.3.6.1.4.1.171.10.75.16.1.23.3.1.1.1SnmpAdminString (SIZE(1..15))read-onlycurrent
swAuthUserPassword
OBJECT-TYPE
This object is used to set 802.1X Local user Password, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.
1.3.6.1.4.1.171.10.75.16.1.23.3.1.1.2DisplayString (SIZE(1..15))read-writecurrent
swAuthUserStatus
OBJECT-TYPE
The status of this conceptual row in the swAuthUserTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthUserName objects must be explicitly set.
1.3.6.1.4.1.171.10.75.16.1.23.3.1.1.3RowStatusread-createcurrent
swAuthRadiusServer
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.23.4
iPv4swAuthRadiusServerTable
OBJECT-TYPE
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
1.3.6.1.4.1.171.10.75.16.1.23.4.1not-accessibleobsolete
iPv4swAuthRadiusServerEntry
OBJECT-TYPE
The configuration information for an Authenticator Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1not-accessibleobsolete
iPv4swAuthRadiusServerIndex
OBJECT-TYPE
A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1.1INTEGER (1..3)read-onlyobsolete
iPv4swAuthRadiusServerAddress
OBJECT-TYPE
The IP address of the RADIUS server referred to in this table entry.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1.2IpAddressread-writeobsolete
iPv4swAuthRadiusServerAuthenticationPort
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1.3INTEGER (1..65535)read-writeobsolete
iPv4swAuthRadiusServerAccountingPort
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1.4INTEGER (1..65535)read-writeobsolete
iPv4swAuthRadiusServerTimeout
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1.5INTEGER (1..255)read-writeobsolete
iPv4swAuthRadiusServerRetransmit
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1.6INTEGER (1..255)read-writeobsolete
iPv4swAuthRadiusServerKey
OBJECT-TYPE
This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1.7DisplayString (SIZE(1..15))read-writeobsolete
iPv4swAuthRadiusServerStatus
OBJECT-TYPE
The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set.
1.3.6.1.4.1.171.10.75.16.1.23.4.1.1.8RowStatusread-createobsolete
swAuthRadiusServerTable
OBJECT-TYPE
A table that contains the configuration objects for the Authenticator PAE associated with each port. An entry appears in this table for each port that may authenticate access to itself.
1.3.6.1.4.1.171.10.75.16.1.23.4.2not-accessiblecurrent
swAuthRadiusServerEntry
OBJECT-TYPE
The configuration information for an Authenticator Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1not-accessiblecurrent
swAuthRadiusServerIndex
OBJECT-TYPE
A unique value for Authentication RADIUS Server index. Its value ranges between 1 and 3.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.1INTEGER (1..3)read-onlycurrent
swAuthRadiusIPType
OBJECT-TYPE
The IP address of the RADIUS server IP type referred to in this table entry.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.2INTEGER (1..2)read-writecurrent
swAuthRadiusServerAddress
OBJECT-TYPE
The IP address of the RADIUS server referred to in this table entry.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.3Ipv6Addressread-writecurrent
swAuthRadiusServerInterfaceName
OBJECT-TYPE
Specifies the interface name when the swAuthRadiusServerAddress is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.4OCTET STRINGread-createcurrent
swAuthRadiusServerAuthenticationPort
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.5INTEGER (1..65535)read-writecurrent
swAuthRadiusServerAccountingPort
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.6INTEGER (1..65535)read-writecurrent
swAuthRadiusServerTimeout
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.7INTEGER (1..255)read-writecurrent
swAuthRadiusServerRetransmit
OBJECT-TYPE
The value is for setting UDP Port.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.8INTEGER (1..255)read-writecurrent
swAuthRadiusServerKey
OBJECT-TYPE
This object is used to set 802.1X Radius Server Key, The following characters are allowed to input: semicolon, question mark, space, and double quotation mark.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.9DisplayString (SIZE(1..15))read-writecurrent
swAuthRadiusServerStatus
OBJECT-TYPE
The status of this conceptual row in the swAuthRadiusServerTable. An entry in this table is not qualified for activation until instances of all corresponding columns have been initialized, either through default values, or through Set operations. The swAuthRadiusServerIndex objects must be explicitly set.
1.3.6.1.4.1.171.10.75.16.1.23.4.2.1.10RowStatusread-createcurrent
companyGuestVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.24
guestVlanName
OBJECT-TYPE
The VLAN name of guest VLAN.
1.3.6.1.4.1.171.10.75.16.1.24.1DisplayString (SIZE(1..32))read-writecurrent
guestVlanPort
OBJECT-TYPE
This object indicates the guest VLAN port members of this device.
1.3.6.1.4.1.171.10.75.16.1.24.2PortListread-writecurrent
guestVlanDelState
OBJECT-TYPE
Used to delete the guest VLAN.
1.3.6.1.4.1.171.10.75.16.1.24.3INTEGER {none(1), start(2)}read-writecurrent
companyMacNotify
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.25
macNotifyState
OBJECT-TYPE
This object can enabled or disabled MAC Notification.
1.3.6.1.4.1.171.10.75.16.1.25.1INTEGER {enabled(1), disabled(2)}read-writecurrent
macNotifyInterval
OBJECT-TYPE
This object indicates the time interval in second for trigger the MAC notify message.
1.3.6.1.4.1.171.10.75.16.1.25.2INTEGER (1..2147483647)read-writecurrent
macNotifyHistorySize
OBJECT-TYPE
This object indicates the history size of variation MAC in address table. The default value is 1 .
1.3.6.1.4.1.171.10.75.16.1.25.3INTEGER (1..500)read-writecurrent
macNotifyCtrlTable
OBJECT-TYPE
A table to control Loopback detection features either for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.16.1.25.4not-accessiblecurrent
macNotifyCtrlEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.25.4.1not-accessiblecurrent
macNotifyCtrlIndex
OBJECT-TYPE
The interface index of the port for which the configuration in this entry applies. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.25.4.1.1Integer32 (1..26)read-onlycurrent
macNotifyPortStatus
OBJECT-TYPE
Provides control to per port enable or disable the loopback detection function. Default is disabled.
1.3.6.1.4.1.171.10.75.16.1.25.4.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
macNotifyInfo
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.25.5
macNotifyInfoDiscription
OBJECT-TYPE
This object indicates the information for the device MAC address changes. And the detailed information include: Operation Code + MAC address + Box ID + Port Number + Zero... Operation Code: 1, 2 and 3 1 means learned a new MAC address 2 means deleted an old MAC address. 3 means station movement. Box ID: The switch box ID, for standalone device, it always 1. Port Number: The port number learned or deleted for the box. Zero: Used to separate each message (Operate Code + MAC address + Box ID + Port Number).
1.3.6.1.4.1.171.10.75.16.1.25.5.1OCTET STRING (SIZE(1..1024))accessible-for-notifycurrent
companyISMVLAN
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.27
igmpMulticastVlanStatus
OBJECT-TYPE
Enable/Disable IGMP Multicast Vlan function.
1.3.6.1.4.1.171.10.75.16.1.27.1INTEGER {enabled(1), disabled(2)}read-writecurrent
igmpMulticastVlanTable
OBJECT-TYPE
Information about the IGMP snooping multicast VLAN table.
1.3.6.1.4.1.171.10.75.16.1.27.2not-accessiblecurrent
igmpMulticastVlanEntry
OBJECT-TYPE
The entry of igmpMulticastVlanTable.
1.3.6.1.4.1.171.10.75.16.1.27.2.1not-accessiblecurrent
igmpMulticastVlanid
OBJECT-TYPE
This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.1INTEGER (2..4094)read-onlycurrent
igmpMulticastVlanName
OBJECT-TYPE
This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.2DisplayString (SIZE(0..32))read-createcurrent
igmpMulticastVlanSourcePort
OBJECT-TYPE
This object indicates the port list of the source ports of the IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.3PortListread-writecurrent
igmpMulticastVlanMemberPort
OBJECT-TYPE
This object indicates the port list of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from the member ports will be forwarded to the source ports.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.4PortListread-writecurrent
igmpMulticastVlanTagMemberPort
OBJECT-TYPE
This object indicates the port list of the tag member ports of the IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.5PortListread-writecurrent
igmpMulticastVlanUntaggedSourcePort
OBJECT-TYPE
This object indicates the port list of the untag source ports of the IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.6PortListread-writecurrent
igmpMulticastVlanState
OBJECT-TYPE
This object can be used to enable or disable the IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.7INTEGER {enabled(1), disabled(2)}read-writecurrent
igmpMulticastVlanReplaceSourceIp
OBJECT-TYPE
The replacement source IP of this multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.8IpAddressread-writecurrent
igmpMulticastVlanRemapPriority
OBJECT-TYPE
The remap priority of this multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.9INTEGER (-1..7)read-writecurrent
igmpMulticastVlanReplacePriority
OBJECT-TYPE
The replacement priority of this multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.10INTEGER {enabled(1), disabled(2)}read-writecurrent
igmpMulticastVlanRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.27.2.1.11RowStatusread-createcurrent
igmpMulticastVlanGroupTable
OBJECT-TYPE
The table containing the IGMP snooping multicast VLAN group information
1.3.6.1.4.1.171.10.75.16.1.27.3not-accessiblecurrent
igmpMulticastVlanGroupEntry
OBJECT-TYPE
Information about the current IGMP snooping multicast VLAN group.
1.3.6.1.4.1.171.10.75.16.1.27.3.1not-accessiblecurrent
igmpMulticastVlanGroupVid
OBJECT-TYPE
This object indicates the VID of the IGMP snooping multicast VLAN group.
1.3.6.1.4.1.171.10.75.16.1.27.3.1.1INTEGER (1..4094)read-onlycurrent
igmpMulticastVlanGroupFromIp
OBJECT-TYPE
Specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.3.1.2IpAddressread-onlycurrent
igmpMulticastVlanGroupToIp
OBJECT-TYPE
Specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.3.1.3IpAddressread-onlycurrent
igmpMulticastVlanGroupStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.27.3.1.4RowStatusread-createcurrent
multicastVlanTable
OBJECT-TYPE
Information about the IGMP/MLD snooping multicast VLAN table.
1.3.6.1.4.1.171.10.75.16.1.27.4not-accessiblecurrent
multicastVlanEntry
OBJECT-TYPE
The entry of multicastVlanTable.
1.3.6.1.4.1.171.10.75.16.1.27.4.1not-accessiblecurrent
multicastVlanid
OBJECT-TYPE
This object indicates the VLAN ID of the IGMP/MLD snooping multicast VLAN entry.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.1INTEGER (2..4094)read-onlycurrent
multicastVlanName
OBJECT-TYPE
This object indicates the VLAN name of the IGMP/MLD snooping multicast VLAN entry.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.2DisplayString (SIZE(0..32))read-createcurrent
multicastVlanSourcePort
OBJECT-TYPE
This object indicates the port list of the source ports of the IGMP/MLD snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from themember ports will be forwarded to the source ports.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.3PortListread-writecurrent
multicastVlanMemberPort
OBJECT-TYPE
This object indicates the port list of the member ports of the IGMP/MLD snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry and the IGMP control messages received from themember ports will be forwarded to the source ports.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.4PortListread-writecurrent
multicastVlanTagMemberPort
OBJECT-TYPE
This object indicates the port list of the tag member ports of the IGMP/MLD snooping multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.5PortListread-writecurrent
multicastVlanUntaggedSourcePort
OBJECT-TYPE
This object indicates the port list of the untag source ports of the IGMP/MLD snooping multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.6PortListread-writecurrent
multicastVlanState
OBJECT-TYPE
This object can be used to enable or disable the IGMP/MLD snooping multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.7INTEGER {enabled(1), disabled(2)}read-writecurrent
multicastVlanIgmpReplaceSourceIp
OBJECT-TYPE
The replacement source IP of this IGMP snooping multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.8IpAddressread-writecurrent
multicastVlanMldReplaceSourceIp
OBJECT-TYPE
The replacement source IP of this MLD snooping multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.9Ipv6Addressread-writecurrent
multicastVlanRemapPriority
OBJECT-TYPE
The remap priority of this multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.10INTEGER (-1..7)read-writecurrent
multicastVlanReplacePriority
OBJECT-TYPE
The replacement priority of this multicast VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.11INTEGER {enabled(1), disabled(2)}read-writecurrent
multicastVlanRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.27.4.1.12RowStatusread-createcurrent
multicastVlanGroupTable
OBJECT-TYPE
The table containing the IGMP/MLD snooping multicast VLAN group information
1.3.6.1.4.1.171.10.75.16.1.27.5not-accessiblecurrent
multicastVlanGroupEntry
OBJECT-TYPE
The entry of multicastVlanGroupTable.
1.3.6.1.4.1.171.10.75.16.1.27.5.1not-accessiblecurrent
multicastVlanGroupVid
OBJECT-TYPE
This object indicates the VID of the IGMP/MLD snooping multicast VLAN group.
1.3.6.1.4.1.171.10.75.16.1.27.5.1.1INTEGER (1..4094)read-onlycurrent
multicastVlanGroupIpType
OBJECT-TYPE
Type of specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.5.1.2INTEGER {iPv4(1), iPv6(2)}read-onlycurrent
multicastVlanGroupFromIp
OBJECT-TYPE
Specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.5.1.3Ipv6Addressread-onlycurrent
multicastVlanGroupToIp
OBJECT-TYPE
Specifies the multicast address list for this VLAN.
1.3.6.1.4.1.171.10.75.16.1.27.5.1.4Ipv6Addressread-onlycurrent
multicastVlanGroupStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.27.5.1.5RowStatusread-createcurrent
companyDHCPRelay
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.28
dhcpBOOTPRelayControl
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.28.1
dhcpBOOTPRelayState
OBJECT-TYPE
This object indicates DHCP relay function is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.28.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
dhcpBOOTPRelayHopCount
OBJECT-TYPE
This object indicates the maximum number of router hops that the BOOTP packets can cross.
1.3.6.1.4.1.171.10.75.16.1.28.1.2INTEGER (1..16)read-writecurrent
dhcpBOOTPRelayTimeThreshold
OBJECT-TYPE
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet.
1.3.6.1.4.1.171.10.75.16.1.28.1.3INTEGER (0..65535)read-writecurrent
dhcpBOOTPRelayEnablePortlist
OBJECT-TYPE
This object indicates DHCP relay function is enabled or disabled by portlist.
1.3.6.1.4.1.171.10.75.16.1.28.1.4PortListread-writecurrent
dhcpRelayVlanTable
OBJECT-TYPE
This table indicates the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.28.1.5not-accessiblecurrent
dhcpRelayVlanTableEntry
OBJECT-TYPE
A list of information indicates the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.28.1.5.1not-accessiblecurrent
dhcpRelayVlanSettingsVLANID
OBJECT-TYPE
This object displays the current VLAN ID of the device.
1.3.6.1.4.1.171.10.75.16.1.28.1.5.1.1INTEGER (1..4094)read-onlycurrent
dhcpRelayVlanSettingsState
OBJECT-TYPE
This object indicates DHCP relay function of VLAN is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.28.1.5.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
dhcpBOOTPRelayManagement
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.28.2
dhcpBOOTPRelayInterfaceSettingsTable
OBJECT-TYPE
This table indicates the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.28.2.1not-accessiblecurrent
dhcpBOOTPRelayInterfaceSettingsEntry
OBJECT-TYPE
A list of information indicates the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.28.2.1.1not-accessiblecurrent
dhcpBOOTPRelayInterface
OBJECT-TYPE
This object indicates the name of the IP interface.
1.3.6.1.4.1.171.10.75.16.1.28.2.1.1.1DisplayString (SIZE(0..12))read-onlycurrent
dhcpBOOTPRelayServerIP
OBJECT-TYPE
This object indicates the DHCP server IP address.
1.3.6.1.4.1.171.10.75.16.1.28.2.1.1.2IpAddressread-onlycurrent
dhcpBOOTPRelayInterfaceSettingsRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.28.2.1.1.3RowStatusread-createcurrent
dhcpBOOTPRelayManagementOption82
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.28.2.2
dhcpBOOTPRelayOption82State
OBJECT-TYPE
This object indicates DHCP relay option 82 function is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.28.2.2.1INTEGER {enabled(1), disabled(2)}read-writecurrent
dhcpBOOTPRelayOption82CheckState
OBJECT-TYPE
This object indicates DHCP relay option 82 Check function is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.28.2.2.2INTEGER {enabled(1), disabled(2)}read-writecurrent
dhcpBOOTPRelayOption82Policy
OBJECT-TYPE
This object indicates DHCP relay option 82 policy.
1.3.6.1.4.1.171.10.75.16.1.28.2.2.3INTEGER {replace(1), drop(2), keep(3)}read-writecurrent
dhcpBOOTPRelayOption82RemoteIDType
OBJECT-TYPE
This object indicates the type of remote ID. If the type is default, the remote ID will be the MAC address of the device, otherwise, the remote ID can be defined by writing to the swDHCPRelayOption82RemoteID object.
1.3.6.1.4.1.171.10.75.16.1.28.2.2.4INTEGER {default(1), userdefined(2), userdefinedhex(3)}read-writecurrent
dhcpBOOTPRelayOption82RemoteID
OBJECT-TYPE
This object displays the current remote ID of the device. If swDHCPRelayOption82RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If swDHCPRelayOption82RemoteIDType is set to user-defined or user-defined-hex, a new value can be written to this object.
1.3.6.1.4.1.171.10.75.16.1.28.2.2.5DisplayStringread-writecurrent
dhcpBOOTPRelayOption82CircuitIDType
OBJECT-TYPE
This object indicates the type of remote ID. If the type is default, the circuit ID will be blank, otherwise, the circuit ID can be defined by writing to the dhcpBOOTPRelayOption82CircuitID object.
1.3.6.1.4.1.171.10.75.16.1.28.2.2.7INTEGER {default(1), userdefined(2), userdefinedhex(3)}read-writecurrent
dhcpBOOTPRelayOption82CircuitID
OBJECT-TYPE
This object displays the current remote ID of the device. If dhcpBOOTPRelayOption82CircuitIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If dhcpBOOTPRelayOption82CircuitIDType is set to user-defined or user-defined-hex, a new value can be written to this object.
1.3.6.1.4.1.171.10.75.16.1.28.2.2.8DisplayStringread-writecurrent
companyDHCPLocalRelay
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.29
dhcpLocalRelayGlobalState
OBJECT-TYPE
This object indicates DHCP local relay function of VLAN is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.29.1INTEGER {enabled(1), disabled(2)}read-writecurrent
dhcpLocalRelayTable
OBJECT-TYPE
This table indicates the IP address as a destination to forward (local relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.29.2not-accessiblecurrent
dhcpLocalRelayTableEntry
OBJECT-TYPE
A list of information indicates the IP address as a destination to forward (local relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.29.2.1not-accessiblecurrent
dhcpLocalRelaySettingsVLANID
OBJECT-TYPE
This object displays the current VLAN ID of the device.
1.3.6.1.4.1.171.10.75.16.1.29.2.1.1INTEGER (1..4094)read-onlycurrent
dhcpLocalRelaySettingsState
OBJECT-TYPE
This object indicates DHCP local relay function of VLAN is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.29.2.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
dhcpLocalRelayEnablePortlist
OBJECT-TYPE
This object indicates DHCP local relay function is enabled or disabled by portlist.
1.3.6.1.4.1.171.10.75.16.1.29.3PortListread-writecurrent
companyTrapSetting
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.30
sysTrapIP
OBJECT-TYPE
The smart console utility's IP address is used to recive trap events.
1.3.6.1.4.1.171.10.75.16.1.30.1IpAddressread-writecurrent
sysTrapSystemEvent
OBJECT-TYPE
Enable/Disable system trap events in the switch system.
1.3.6.1.4.1.171.10.75.16.1.30.2INTEGER {none(0), deviceBootUp(1), illegalLogin(2), both(3)}read-writecurrent
sysTrapFiberPortEvent
OBJECT-TYPE
Enable/Disable fiber port trap event in the system.
1.3.6.1.4.1.171.10.75.16.1.30.3INTEGER {enable(1), disable(2)}read-writecurrent
sysTrapTwistedPortEvent
OBJECT-TYPE
Enable/Disable twisted port trap event in the system.
1.3.6.1.4.1.171.10.75.16.1.30.4INTEGER {enable(1), disable(2)}read-writecurrent
sysTrapStateChangeEvent
OBJECT-TYPE
Enable/Disable RSTP state change trap event in the system.
1.3.6.1.4.1.171.10.75.16.1.30.5INTEGER {enable(1), disable(2)}read-writecurrent
sysTrapFirmUpgradeEvent
OBJECT-TYPE
Enable/Disable firmware upgrading trap event in the system.
1.3.6.1.4.1.171.10.75.16.1.30.6INTEGER {enable(1), disable(2)}read-writecurrent
sysTrapStatus
OBJECT-TYPE
Enable/Disable trap event in the system.
1.3.6.1.4.1.171.10.75.16.1.30.10INTEGER {enable(1), disable(2)}read-writecurrent
sysTrapPortSecurity
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.30.13INTEGER {enabled(1), disabled(2)}read-writecurrent
sysTrapIMPBViolation
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.30.14INTEGER {enabled(1), disabled(2)}read-writecurrent
sysTrapLBD
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.30.15INTEGER {enabled(1), disabled(2)}read-writecurrent
sysTrapDHCPServerScreening
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.30.16INTEGER {enabled(1), disabled(2)}read-writecurrent
sysTrapDuplicateIPDetected
OBJECT-TYPE
This object is for enabling or disabling send gratuitous trap when IP address conflicted in the network.
1.3.6.1.4.1.171.10.75.16.1.30.17INTEGER {enabled(1), disabled(2)}read-writecurrent
companyLLDPSetting
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32
dlinklldpState
OBJECT-TYPE
This object is used for enabling or disabling LLDP in the system.
1.3.6.1.4.1.171.10.75.16.1.32.1INTEGER {enable(1), disable(2)}read-writecurrent
dlinklldpMsgHoldMultiplier
OBJECT-TYPE
The time-to-live value expressed as a multiple of the lldpMessageTxInterval object.The actual time-to-live value used in LLDP frames, transmitted on behalf of this LLDP agent, can be expressed by the following formula: TTL = min(65535, (lldpMessageTxInterval * lldpMessageTxHoldMultiplier))
1.3.6.1.4.1.171.10.75.16.1.32.2INTEGER (2..10)read-writecurrent
dlinklldpMsgTxInterval
OBJECT-TYPE
This object is used for LLDP packet update frequency. The timer in units of seconds.
1.3.6.1.4.1.171.10.75.16.1.32.3INTEGER (5..32768)read-writecurrent
dlinklldpReinitDelay
OBJECT-TYPE
This object is used for LLDP Reinitialization Delay. The timer in units of seconds.
1.3.6.1.4.1.171.10.75.16.1.32.4INTEGER (1..10)read-writecurrent
dlinklldpTxDelay
OBJECT-TYPE
The lldpTxDelay indicates the delay (in units of seconds) between successive LLDP frame transmissions initiated by value/status changes in the LLDP local systems MIB. The recommended value for the lldpTxDelay is set by the following formula: 1 <= lldpTxDelay <= (0.25 * lldpMessageTxInterval).
1.3.6.1.4.1.171.10.75.16.1.32.5INTEGER (1..8192)read-writecurrent
dlinklldpConfigManAddrPortsTxEnable
OBJECT-TYPE
A set of ports that are identified by a PortList, in which each port is represented as a bit. The corresponding local system management address instance will be transmitted on the member ports of the lldpManAddrPortsTxEnable. The default value for lldpConfigManAddrPortsTxEnable object is empty binary string, which means no ports are specified for advertising indicated management address instance.
1.3.6.1.4.1.171.10.75.16.1.32.6PortListread-writecurrent
lldpPortConfigTable
OBJECT-TYPE
The table that controls LLDP frame transmission on individual ports.
1.3.6.1.4.1.171.10.75.16.1.32.11not-accessiblecurrent
lldpPortConfigEntry
OBJECT-TYPE
LLDP configuration information for a particular port. This configuration parameter controls the transmission and the reception of LLDP frames on those ports whose rows are created in this table.
1.3.6.1.4.1.171.10.75.16.1.32.11.1not-accessiblecurrent
lldpPortConfigPortNum
OBJECT-TYPE
The index value used to identify the port component (contained in the local chassis with the LLDP agent) associated with this entry. The value of this object is used as a port index to the lldpPortConfigTable.
1.3.6.1.4.1.171.10.75.16.1.32.11.1.1LldpPortNumbernot-accessiblecurrent
lldpPortConfigAdminStatus
OBJECT-TYPE
The administratively desired status of the local LLDP agent. If the associated lldpPortConfigAdminStatus object has a value of 'txOnly(1)', then LLDP agent will transmit LLDP frames on this port and it will not store any information about the remote systems connected. If the associated lldpPortConfigAdminStatus object has a value of 'rxOnly(2)', then the LLDP agent will receive, but it will not transmit LLDP frames on this port. If the associated lldpPortConfigAdminStatus object has a value of 'txAndRx(3)', then the LLDP agent will transmit and receive LLDP frames on this port. If the associated lldpPortConfigAdminStatus object has a value of 'disabled(4)', then LLDP agent will not transmit or receive LLDP frames on this port. If there is remote systems information which is received on this port and stored in other tables, before the port's lldpPortConfigAdminStatus becomes disabled, then the information will naturally age out.
1.3.6.1.4.1.171.10.75.16.1.32.11.1.2INTEGER {txOnly(1), rxOnly(2), txAndRx(3), disabled(4)}read-writecurrent
lldpPortConfigNotificationEnable
OBJECT-TYPE
The lldpPortConfigNotificationEnable controls, on a per port basis, whether or not notifications from the agent are enabled. The value true(1) means that notifications are enabled; the value false(2) means that they are not.
1.3.6.1.4.1.171.10.75.16.1.32.11.1.3TruthValueread-writecurrent
lldpPortConfigTLVsTxEnable
OBJECT-TYPE
The lldpPortConfigTLVsTxEnable, defined as a bitmap, includes the basic set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to a TLV type associated with a specific optional TLV. It should be noted that the organizationally-specific TLVs are excluded from the lldpTLVsTxEnable bitmap. LLDP Organization Specific Information Extension MIBs should have similar configuration object to control transmission of their organizationally defined TLVs. The bit 'portDesc(0)' indicates that LLDP agent should transmit 'Port Description TLV'. The bit 'sysName(1)' indicates that LLDP agent should transmit 'System Name TLV'. The bit 'sysDesc(2)' indicates that LLDP agent should transmit 'System Description TLV'. The bit 'sysCap(3)' indicates that LLDP agent should transmit 'System Capabilities TLV'. There is no bit reserved for the management address TLV type since transmission of management address TLVs are controlled by another object, lldpConfigManAddrTable. The default value for lldpPortConfigTLVsTxEnable object is empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.11.1.4Bits {portDesc(0), sysName(1), sysDesc(2), sysCap(3)}read-writecurrent
lldpXdot3Objects
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32.12
lldpXdot3Config
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32.12.1
lldpXdot3PortConfigTable
OBJECT-TYPE
A table that controls selection of LLDP TLVs to be transmitted on individual ports.
1.3.6.1.4.1.171.10.75.16.1.32.12.1.1not-accessiblecurrent
lldpXdot3PortConfigEntry
OBJECT-TYPE
LLDP configuration information that controls the transmission of IEEE 802.3 organizationally defined TLVs on LLDP transmission capable ports. This configuration object augments the lldpPortConfigEntry of the LLDP-MIB, therefore it is only present along with the port configuration defined by the associated lldpPortConfigEntry entry. Each active lldpXdot3PortConfigEntry must be from non-volatile storage (along with the corresponding lldpPortConfigEntry) after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.12.1.1.1not-accessiblecurrent
lldpXdot3PortConfigTLVsTxEnable
OBJECT-TYPE
The lldpXdot3PortConfigTLVsTxEnable, defined as a bitmap, includes the IEEE 802.3 organizationally defined set of LLDP TLVs whose transmission is allowed on the local LLDP agent by the network management. Each bit in the bitmap corresponds to an IEEE 802.3 subtype associated with a specific IEEE 802.3 optional TLV. The bit 0 is not used since there is no corresponding subtype. The bit 'macPhyConfigStatus(0)' indicates that LLDP agent should transmit 'MAC/PHY configuration/status TLV'. The bit 'powerViaMDI(1)' indicates that LLDP agent should transmit 'Power via MDI TLV'. The bit 'linkAggregation(2)' indicates that LLDP agent should transmit 'Link Aggregation TLV'. The bit 'maxFrameSize(3)' indicates that LLDP agent should transmit 'Maximum-frame-size TLV'. The default value for lldpXdot3PortConfigTLVsTxEnable object is an empty set, which means no enumerated values are set. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.12.1.1.1.1Bits {macPhyConfigStatus(0), powerViaMDI(1), linkAggregation(2), maxFrameSize(3)}read-writecurrent
lldpXdot3LocalData
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32.12.2
lldpXdot3LocPortTable
OBJECT-TYPE
This table contains one row per port of Ethernet port information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.1not-accessiblecurrent
lldpXdot3LocPortEntry
OBJECT-TYPE
Information about a particular port component.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.1.1not-accessiblecurrent
lldpXdot3LocPortAutoNegSupported
OBJECT-TYPE
The truth value used to indicate whether the given port (associated with the local system) supports Auto-negotiation.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.1.1.1TruthValueread-onlycurrent
lldpXdot3LocPortAutoNegEnabled
OBJECT-TYPE
The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.1.1.2TruthValueread-onlycurrent
lldpXdot3LocPortAutoNegAdvertisedCap
OBJECT-TYPE
This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.1.1.3OCTET STRING (SIZE(2))read-onlycurrent
lldpXdot3LocPortOperMauType
OBJECT-TYPE
An integer value that indicates the operational MAU type of the given port on the local system. This object contains the integer value derived from the list position of the corresponding dot3MauType as listed in IETF RFC 3636 (or subsequent revisions) and is equal to the last number in the respective dot3MauType OID. For example, if the ifMauType object is dot3MauType1000BaseTHD which corresponds to {dot3MauType 29}, the numerical value of this field will be 29. For MAU types not listed in RFC 3636 (or subsequent revisions), the value of this field shall be set to zero.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.1.1.4Integer32 (0..2147483647)read-onlycurrent
lldpXdot3LocPowerTable
OBJECT-TYPE
This table contains one row per port of power ethernet information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.2not-accessiblecurrent
lldpXdot3LocPowerEntry
OBJECT-TYPE
Information about a particular port component.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.2.1not-accessiblecurrent
lldpXdot3LocPowerPortClass
OBJECT-TYPE
The value that identifies the port Class of the given port associated with the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.2.1.1LldpPowerPortClassread-onlycurrent
lldpXdot3LocPowerMDISupported
OBJECT-TYPE
The truth value used to indicate whether the MDI power is supported on the given port associated with the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.2.1.2TruthValueread-onlycurrent
lldpXdot3LocPowerMDIEnabled
OBJECT-TYPE
The truth value used to identify whether MDI power is enabled on the given port associated with the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.2.1.3TruthValueread-onlycurrent
lldpXdot3LocPowerPairControlable
OBJECT-TYPE
The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair selection can be controlled on the given port associated with the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.2.1.4TruthValueread-onlycurrent
lldpXdot3LocPowerPairs
OBJECT-TYPE
This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.2.1.5Integer32 (1 | 2)read-onlycurrent
lldpXdot3LocPowerClass
OBJECT-TYPE
This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.2.1.6Integer32 (1 | 2 | 3 | 4 | 5)read-onlycurrent
lldpXdot3LocLinkAggTable
OBJECT-TYPE
This table contains one row per port of link aggregation information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.3not-accessiblecurrent
lldpXdot3LocLinkAggEntry
OBJECT-TYPE
Link Aggregation information about a particular port component.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.3.1not-accessiblecurrent
lldpXdot3LocLinkAggStatus
OBJECT-TYPE
The bitmap value contains the link aggregation capabilities and the current aggregation status of the link.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.3.1.1LldpLinkAggStatusMapread-onlycurrent
lldpXdot3LocLinkAggPortId
OBJECT-TYPE
This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port component in link aggregation. If the port is not in link aggregation state and/or it does not support link aggregation, this value should be set to zero.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.3.1.2Integer32 (0 | 1..2147483647)read-onlycurrent
lldpXdot3LocMaxFrameSizeTable
OBJECT-TYPE
This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) on the local system known to this agent.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.4not-accessiblecurrent
lldpXdot3LocMaxFrameSizeEntry
OBJECT-TYPE
Maximum Frame Size information about a particular port component.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.4.1not-accessiblecurrent
lldpXdot3LocMaxFrameSize
OBJECT-TYPE
An integer value indicating the maximum supported frame size in octets on the given port of the local system.
1.3.6.1.4.1.171.10.75.16.1.32.12.2.4.1.1Integer32 (0..65535)read-onlycurrent
lldpXdot3RemoteData
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32.12.3
lldpXdot3RemPortTable
OBJECT-TYPE
This table contains Ethernet port information (as a part of the LLDP 802.3 organizational extension) of the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.1not-accessiblecurrent
lldpXdot3RemPortEntry
OBJECT-TYPE
Information about a particular physical network connection.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.1.1not-accessiblecurrent
lldpXdot3RemPortAutoNegSupported
OBJECT-TYPE
The truth value used to indicate whether the given port (associated with remote system) supports Auto-negotiation.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.1.1.1TruthValueread-onlycurrent
lldpXdot3RemPortAutoNegEnabled
OBJECT-TYPE
The truth value used to indicate whether port Auto-negotiation is enabled on the given port associated with the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.1.1.2TruthValueread-onlycurrent
lldpXdot3RemPortAutoNegAdvertisedCap
OBJECT-TYPE
This object contains the value (bitmap) of the ifMauAutoNegCapAdvertisedBits object (defined in IETF RFC 3636) which is associated with the given port on the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.1.1.3OCTET STRING (SIZE(2))read-onlycurrent
lldpXdot3RemPortOperMauType
OBJECT-TYPE
An integer value that indicates the operational MAU type of the sending device. This object contains the integer value derived from the list position of the corresponding dot3MauType as listed in in IETF RFC 3636 (or subsequent revisions) and is equal to the last number in the respective dot3MauType OID. For example, if the ifMauType object is dot3MauType1000BaseTHD which corresponds to {dot3MauType 29}, the numerical value of this field will be 29. For MAU types not listed in RFC 3636 (or subsequent revisions), the value of this field shall be set to zero.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.1.1.4Integer32 (0..2147483647)read-onlycurrent
lldpXdot3RemPowerTable
OBJECT-TYPE
This table contains Ethernet power information (as a part of the LLDP 802.3 organizational extension) of the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.2not-accessiblecurrent
lldpXdot3RemPowerEntry
OBJECT-TYPE
Information about a particular physical network connection.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.2.1not-accessiblecurrent
lldpXdot3RemPowerPortClass
OBJECT-TYPE
The value that identifies the port Class of the given port associated with the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.2.1.1LldpPowerPortClassread-onlycurrent
lldpXdot3RemPowerMDISupported
OBJECT-TYPE
The truth value used to indicate whether the MDI power is supported on the given port associated with the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.2.1.2TruthValueread-onlycurrent
lldpXdot3RemPowerMDIEnabled
OBJECT-TYPE
The truth value used to identify whether MDI power is enabled on the given port associated with the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.2.1.3TruthValueread-onlycurrent
lldpXdot3RemPowerPairControlable
OBJECT-TYPE
The truth value is derived from the value of pethPsePortPowerPairsControlAbility object (defined in IETF RFC 3621) and is used to indicate whether the pair selection can be controlled on the given port associated with the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.2.1.4TruthValueread-onlycurrent
lldpXdot3RemPowerPairs
OBJECT-TYPE
This object contains the value of the pethPsePortPowerPairs object (defined in IETF RFC 3621) which is associated with the given port on the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.2.1.5Integer32 (1 | 2)read-onlycurrent
lldpXdot3RemPowerClass
OBJECT-TYPE
This object contains the value of the pethPsePortPowerClassifications object (defined in IETF RFC 3621) which is associated with the given port on the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.2.1.6Integer32 (1 | 2 | 3 | 4 | 5)read-onlycurrent
lldpXdot3RemLinkAggTable
OBJECT-TYPE
This table contains port link aggregation information (as a part of the LLDP 802.3 organizational extension) of the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.3not-accessiblecurrent
lldpXdot3RemLinkAggEntry
OBJECT-TYPE
Link Aggregation information about remote system's port component.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.3.1not-accessiblecurrent
lldpXdot3RemLinkAggStatus
OBJECT-TYPE
The bitmap value contains the link aggregation capabilities and the current aggregation status of the link.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.3.1.1LldpLinkAggStatusMapread-onlycurrent
lldpXdot3RemLinkAggPortId
OBJECT-TYPE
This object contains the IEEE 802.3 aggregated port identifier, aAggPortID (IEEE 802.3-2002, 30.7.2.1.1), derived from the ifNumber of the ifIndex for the port component associated with the remote system. If the remote port is not in link aggregation state and/or it does not support link aggregation, this value should be zero.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.3.1.2Integer32 (0 | 1..2147483647)read-onlycurrent
lldpXdot3RemMaxFrameSizeTable
OBJECT-TYPE
This table contains one row per port of maximum frame size information (as a part of the LLDP 802.3 organizational extension) of the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.4not-accessiblecurrent
lldpXdot3RemMaxFrameSizeEntry
OBJECT-TYPE
Maximum Frame Size information about a particular port component.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.4.1not-accessiblecurrent
lldpXdot3RemMaxFrameSize
OBJECT-TYPE
An integer value indicating the maximum supported frame size in octets on the port component associated with the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.12.3.4.1.1Integer32 (0..65535)read-onlycurrent
lldpXdot1Objects
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32.13
lldpXdot1Config
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32.13.1
lldpXdot1ConfigPortVlanTable
OBJECT-TYPE
A table that controls selection of LLDP Port VLAN-ID TLVs to be transmitted on individual ports.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.1not-accessiblecurrent
lldpXdot1ConfigPortVlanEntry
OBJECT-TYPE
LLDP configuration information that controls the transmission of IEEE 802.1 organizationally defined Port VLAN-ID TLV on LLDP transmission capable ports. This configuration object augments the lldpPortConfigEntry of the LLDP-MIB, therefore it is only present along with the port configuration defined by the associated lldpPortConfigEntry entry. Each active lldpConfigEntry must be restored from non-volatile storage (along with the corresponding lldpPortConfigEntry) after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.1.1not-accessiblecurrent
lldpXdot1ConfigPortVlanTxEnable
OBJECT-TYPE
The lldpXdot1ConfigPortVlanTxEnable, which is defined as a truth value and configured by the network management, determines whether the IEEE 802.1 organizationally defined port VLAN TLV transmission is allowed on a given LLDP transmission capable port. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.1.1.1TruthValueread-writecurrent
lldpXdot1ConfigVlanNameTable
OBJECT-TYPE
The table that controls selection of LLDP VLAN name TLV instances to be transmitted on individual ports.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.2not-accessiblecurrent
lldpXdot1ConfigVlanNameEntry
OBJECT-TYPE
LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System VLAN name instance will be transmitted. This configuration object augments the lldpLocVlanEntry, therefore it is only present along with the VLAN Name instance contained in the associated lldpLocVlanNameEntry entry. Each active lldpXdot1ConfigVlanNameEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocVlanNameEntry) after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.2.1not-accessiblecurrent
lldpXdot1ConfigVlanNameTxEnable
OBJECT-TYPE
The boolean value that indicates whether the corresponding Local System VLAN name instance will be transmitted on the port defined by the given lldpXdot1LocVlanNameEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.2.1.1TruthValueread-writecurrent
lldpXdot1ConfigProtoVlanTable
OBJECT-TYPE
The table that controls selection of LLDP Port and Protocol VLAN ID TLV instances to be transmitted on individual ports.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.3not-accessiblecurrent
lldpXdot1ConfigProtoVlanEntry
OBJECT-TYPE
LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol VLAN instance will be transmitted. This configuration object augments the lldpXdot1LocVlanEntry, therefore it is only present along with the Port and Protocol VLAN ID instance contained in the associated lldpXdot1LocVlanEntry entry. Each active lldpXdot1ConfigProtoVlanEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtoVlanEntry) after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.3.1not-accessiblecurrent
lldpXdot1ConfigProtoVlanTxEnable
OBJECT-TYPE
The boolean value that indicates whether the corresponding Local System Port and Protocol VLAN instance will be transmitted on the port defined by the given lldpXdot1LocProtoVlanEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.3.1.1TruthValueread-writecurrent
lldpXdot1ConfigProtocolTable
OBJECT-TYPE
The table that controls selection of LLDP Protocol TLV instances to be transmitted on individual ports.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.4not-accessiblecurrent
lldpXdot1ConfigProtocolEntry
OBJECT-TYPE
LLDP configuration information that specifies the set of ports (represented as a PortList) on which the Local System Protocol instance will be transmitted. This configuration object augments the lldpXdot1LocProtoEntry, therefore it is only present along with the Protocol instance contained in the associated lldpXdot1LocProtoEntry entry. Each active lldpXdot1ConfigProtocolEntry must be restored from non-volatile storage (along with the corresponding lldpXdot1LocProtocolEntry) after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.4.1not-accessiblecurrent
lldpXdot1ConfigProtocolTxEnable
OBJECT-TYPE
The boolean value that indicates whether the corresponding Local System Protocol Identity instance will be transmitted on the port defined by the given lldpXdot1LocProtocolEntry. The value of this object must be restored from non-volatile storage after a re-initialization of the management system.
1.3.6.1.4.1.171.10.75.16.1.32.13.1.4.1.1TruthValueread-writecurrent
lldpXdot1LocalData
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32.13.2
lldpXdot1LocTable
OBJECT-TYPE
This table contains one row per port for IEEE 802.1 organizationally defined LLDP extension on the local system known to this agent.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.1not-accessiblecurrent
lldpXdot1LocEntry
OBJECT-TYPE
Information about IEEE 802.1 organizationally defined LLDP extension.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.1.1not-accessiblecurrent
lldpXdot1LocPortVlanId
OBJECT-TYPE
The integer value used to identify the port's VLAN identifier associated with the local system. A value of zero shall be used if the system either does not know the PVID or does not support port-based VLAN operation.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.1.1.1Integer32 (0 | 1..4094)read-onlycurrent
lldpXdot1LocProtoVlanTable
OBJECT-TYPE
This table contains one or more rows per Port and Protocol VLAN information about the local system.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.2not-accessiblecurrent
lldpXdot1LocProtoVlanEntry
OBJECT-TYPE
Port and protocol VLAN ID Information about a particular port component. There may be multiple port and protocol VLANs, identified by a particular lldpXdot1LocProtoVlanId, configured on the given port.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.2.1not-accessiblecurrent
lldpXdot1LocProtoVlanId
OBJECT-TYPE
The integer value used to identify the port and protocol VLANs associated with the given port associated with the local system. A value of zero shall be used if the system either does not know the protocol VLAN ID (PPVID) or does not support port and protocol VLAN operation.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.2.1.1Integer32 (0 | 1..4094)not-accessiblecurrent
lldpXdot1LocProtoVlanSupported
OBJECT-TYPE
The truth value used to indicate whether the given port (associated with the local system) supports port and protocol VLANs.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.2.1.2TruthValueread-onlycurrent
lldpXdot1LocProtoVlanEnabled
OBJECT-TYPE
The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the local system.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.2.1.3TruthValueread-onlycurrent
lldpXdot1LocVlanNameTable
OBJECT-TYPE
This table contains one or more rows per IEEE 802.1Q VLAN name information on the local system known to this agent.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.3not-accessiblecurrent
lldpXdot1LocVlanNameEntry
OBJECT-TYPE
VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1LocVlanId, configured on the given port.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.3.1not-accessiblecurrent
lldpXdot1LocVlanId
OBJECT-TYPE
The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port is compatible.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.3.1.1VlanIdnot-accessiblecurrent
lldpXdot1LocVlanName
OBJECT-TYPE
The string value used to identify VLAN name identified by the Vlan Id associated with the given port on the local system. This object should contain the value of the dot1QVLANStaticName object (defined in IETF RFC 2674) identified with the given lldpXdot1LocVlanId.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.3.1.2SnmpAdminString (SIZE(1..32))read-onlycurrent
lldpXdot1LocProtocolTable
OBJECT-TYPE
This table contains one or more rows per protocol identity information on the local system known to this agent.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.4not-accessiblecurrent
lldpXdot1LocProtocolEntry
OBJECT-TYPE
Information about particular protocols that are accessible through the given port component. There may be multiple protocols, identified by particular lldpXdot1ProtocolIndex, and lldpLocPortNum.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.4.1not-accessiblecurrent
lldpXdot1LocProtocolIndex
OBJECT-TYPE
This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.4.1.1Integer32 (1..2147483647)not-accessiblecurrent
lldpXdot1LocProtocolId
OBJECT-TYPE
The octet string value used to identify the protocols associated with the given port of the local system.
1.3.6.1.4.1.171.10.75.16.1.32.13.2.4.1.2OCTET STRING (SIZE(1..255))read-onlycurrent
lldpXdot1RemoteData
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.32.13.3
lldpXdot1RemTable
OBJECT-TYPE
This table contains one or more rows per physical network connection known to this agent. The agent may wish to ensure that only one lldpXdot1RemEntry is present for each local port, or it may choose to maintain multiple lldpXdot1RemEntries for the same local port.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.1not-accessiblecurrent
lldpXdot1RemEntry
OBJECT-TYPE
Information about a particular port component.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.1.1not-accessiblecurrent
lldpXdot1RemPortVlanId
OBJECT-TYPE
The integer value used to identify the port's VLAN identifier associated with the remote system. if the remote system either does not know the PVID or does not support port-based VLAN operation, the value of lldpXdot1RemPortVlanId should be zero.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.1.1.1Integer32 (0 | 1..4094)read-onlycurrent
lldpXdot1RemProtoVlanTable
OBJECT-TYPE
This table contains one or more rows per Port and Protocol VLAN information about the remote system, received on the given port.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.2not-accessiblecurrent
lldpXdot1RemProtoVlanEntry
OBJECT-TYPE
Port and protocol VLAN name Information about a particular port component. There may be multiple protocol VLANs, identified by a particular lldpXdot1RemProtoVlanId, configured on the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.2.1not-accessiblecurrent
lldpXdot1RemProtoVlanId
OBJECT-TYPE
The integer value used to identify the port and protocol VLANs associated with the given port associated with the remote system. If port and protocol VLANs are not supported on the given port associated with the remote system, or if the port is not enabled with any port and protocol VLAN, the value of lldpXdot1RemProtoVlanId should be zero.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.2.1.1Integer32 (0 | 1..4094)not-accessiblecurrent
lldpXdot1RemProtoVlanSupported
OBJECT-TYPE
The truth value used to indicate whether the given port (associated with the remote system) is capable of supporting port and protocol VLANs.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.2.1.2TruthValueread-onlycurrent
lldpXdot1RemProtoVlanEnabled
OBJECT-TYPE
The truth value used to indicate whether the port and protocol VLANs are enabled on the given port associated with the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.2.1.3TruthValueread-onlycurrent
lldpXdot1RemVlanNameTable
OBJECT-TYPE
This table contains one or more rows per IEEE 802.1Q VLAN name information about the remote system, received on the given port.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.3not-accessiblecurrent
lldpXdot1RemVlanNameEntry
OBJECT-TYPE
VLAN name Information about a particular port component. There may be multiple VLANs, identified by a particular lldpXdot1RemVlanId, received on the given port.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.3.1not-accessiblecurrent
lldpXdot1RemVlanId
OBJECT-TYPE
The integer value used to identify the IEEE 802.1Q VLAN IDs with which the given port of the remote system is compatible.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.3.1.1VlanIdnot-accessiblecurrent
lldpXdot1RemVlanName
OBJECT-TYPE
The string value used to identify VLAN name identified by the VLAN Id associated with the remote system.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.3.1.2SnmpAdminString (SIZE(1..32))read-onlycurrent
lldpXdot1RemProtocolTable
OBJECT-TYPE
This table contains one or more rows per protocol information about the remote system, received on the given port.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.4not-accessiblecurrent
lldpXdot1RemProtocolEntry
OBJECT-TYPE
Protocol information about a particular port component. There may be multiple protocols, identified by a particular lldpXdot1ProtocolIndex, received on the given port.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.4.1not-accessiblecurrent
lldpXdot1RemProtocolIndex
OBJECT-TYPE
This object represents an arbitrary local integer value used by this agent to identify a particular protocol identity.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.4.1.1Integer32 (1..2147483647)not-accessiblecurrent
lldpXdot1RemProtocolId
OBJECT-TYPE
The octet string value used to identify the protocols associated with the given port of remote system.
1.3.6.1.4.1.171.10.75.16.1.32.13.3.4.1.2OCTET STRING (SIZE(1..255))read-onlycurrent
companyCPUInterfaceFilterGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.33
cpuFilterProfile
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.33.1
ipv4cpuFilterProfileTable
OBJECT-TYPE
A table to CPUInterfaceFilter profile .
1.3.6.1.4.1.171.10.75.16.1.33.1.1not-accessiblecurrent
ipv4cpuFilterProfileEntry
OBJECT-TYPE
Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1not-accessiblecurrent
ipv4cpuFilterProfileNo
OBJECT-TYPE
The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter. The user only allow to create user-defined CPUInterfaceFilter ID. And system-defined CPUInterfaceFilter is read only.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.1Integer32 (1..3)read-onlycurrent
ipv4cpuFilterProfileType
OBJECT-TYPE
The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, l3v6 (11) - for IPv6-based rule
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.2INTEGER {l2(1), l3(2), l3v6(11)}read-writecurrent
ipv4cpuFilterProfileRuleCount
OBJECT-TYPE
The number of rules in this profile.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.3Integer32 (0..65535)read-onlycurrent
ipv4cpuFilterProfileMask
OBJECT-TYPE
Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 (MSB) ------------------------------------------- The value is in Hex format.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.4OCTET STRINGread-writecurrent
ipv4cpuFilterProfileDstMacAddrMask
OBJECT-TYPE
The CPUInterfaceFilter Profile destination MAC address mask. If DST_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleDstMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.5MacAddressread-writecurrent
ipv4cpuFilterProfileSrcMacAddrMask
OBJECT-TYPE
The CPUInterfaceFilter Profile source MAC address mask. If SRC_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.6MacAddressread-writecurrent
ipv4cpuFilterProfileIPProtocol
OBJECT-TYPE
Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.7INTEGER {none(0), icmp(1), igmp(2), tcp(6), udp(17), ipMask(255)}read-writecurrent
ipv4cpuFilterProfileIPProtocolMask
OBJECT-TYPE
The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.8OCTET STRINGread-writecurrent
ipv4cpuFilterProfileDstIpAddrMask
OBJECT-TYPE
The CPUInterfaceFilter Profile destination IP address mask. If DST_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.9IpAddressread-writecurrent
ipv4cpuFilterProfileSrcIpAddrMask
OBJECT-TYPE
The CPUInterfaceFilter Profile source IP address mask. If SRC_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.10IpAddressread-writecurrent
ipv4cpuFilterProfileDstPortMask
OBJECT-TYPE
The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.11OCTET STRINGread-writecurrent
ipv4cpuFilterProfileSrcPortMask
OBJECT-TYPE
The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.12OCTET STRINGread-writecurrent
ipv4cpuFilterProfileStatus
OBJECT-TYPE
This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of cpuFilterProfileType, cpuFilterProfileMask and ProtocolType are not conflicted.
1.3.6.1.4.1.171.10.75.16.1.33.1.1.1.15RowStatusread-createcurrent
cpuFilterProfileTable
OBJECT-TYPE
A table to CPUInterfaceFilter profile .
1.3.6.1.4.1.171.10.75.16.1.33.1.2not-accessiblecurrent
cpuFilterProfileEntry
OBJECT-TYPE
Each entry in this table is a CPUInterfaceFilter profile. Index to the table is CPUInterfaceFilter profile ID.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1not-accessiblecurrent
cpuFilterProfileNo
OBJECT-TYPE
The CPUInterfaceFilter Profile ID. The ID 1 to 50 is user-defined CPUInterfaceFilter, and the ID more than 50 is reserved for system-defined CPUInterfaceFilter. The user only allow to create user-defined CPUInterfaceFilter ID. And system-defined CPUInterfaceFilter is read only.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.1Integer32 (1..3)read-onlycurrent
cpuFilterProfileType
OBJECT-TYPE
The CPUInterfaceFilter Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, l3v6 (11) - for IPv6-based rule
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.2INTEGER {l2(1), l3(2), l3v6(11)}read-writecurrent
cpuFilterProfileRuleCount
OBJECT-TYPE
The number of rules in this profile.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.3Integer32 (0..65535)read-onlycurrent
cpuFilterProfileMask
OBJECT-TYPE
Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC 0 (LSB) L2 SRC_MAC 1 L2 VID 2 L2 8021P_PRIORITY 3 L2 ETHER_TYPE 4 L3 DSCP 5 L3 ICMP_TYPE 6 L3 ICMP_CODE 7 L3 IGMP_TYPE 8 L3 DST_IP 9 L3 SRC_IP 10 L3 DST_PORT 11 L3 SRC_PORT 12 L3 TCPFLAG 13 (MSB) L3 TRAFFIC_CLASS 21 ------------------------------------------- The value is in Hex format.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.4OCTET STRINGread-writecurrent
cpuFilterProfileDstMacAddrMask
OBJECT-TYPE
The CPUInterfaceFilter Profile destination MAC address mask. If DST_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleDstMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.5MacAddressread-writecurrent
cpuFilterProfileSrcMacAddrMask
OBJECT-TYPE
The CPUInterfaceFilter Profile source MAC address mask. If SRC_MAC is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.6MacAddressread-writecurrent
cpuFilterProfileIPProtocol
OBJECT-TYPE
Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.7INTEGER {none(0), icmp(1), igmp(2), tcp(6), udp(17), ipMask(255)}read-writecurrent
cpuFilterProfileIPProtocolMask
OBJECT-TYPE
The CPUInterfaceFilter Profile IP protocol mask. If cpuFilterProfileIPProtocol set to ipMask, this field will be refered. It will work with its member rule field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.8OCTET STRINGread-writecurrent
cpuFilterProfileDstIpAddrMaskType
OBJECT-TYPE
IPv6 Address type.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.9INTEGER {iPv4(1), iPv6(2)}read-writecurrent
cpuFilterProfileDstIpAddrMask
OBJECT-TYPE
The CPUInterfaceFilter Profile destination IP address mask. If DST_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.10Ipv6Addressread-writecurrent
cpuFilterProfileSrcIpAddrMaskType
OBJECT-TYPE
IPv6 Address type.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.11INTEGER {iPv4(1), iPv6(2)}read-writecurrent
cpuFilterProfileSrcIpAddrMask
OBJECT-TYPE
The CPUInterfaceFilter Profile source IP address mask. If SRC_IP is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX format, for example: '255.255.255.0' is presented to 'FFFFFF00'
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.12Ipv6Addressread-writecurrent
cpuFilterProfileDstPortMask
OBJECT-TYPE
The CPUInterfaceFilter Profile UDP/TCP destination port mask. If DST_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.13OCTET STRINGread-writecurrent
cpuFilterProfileSrcPortMask
OBJECT-TYPE
The CPUInterfaceFilter Profile UDP/TCP source port mask. If SRC_PORT is turn on in cpuFilterProfileMask, it will work with its member rule field,cpuFilterL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.14OCTET STRINGread-writecurrent
cpuFilterProfileStatus
OBJECT-TYPE
This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of cpuFilterProfileType, cpuFilterProfileMask and ProtocolType are not conflicted.
1.3.6.1.4.1.171.10.75.16.1.33.1.2.1.15RowStatusread-createcurrent
cpuFilterL2Rule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.33.2
cpuFilterL2RuleTable
OBJECT-TYPE
A table to configure L2 filter rules in the system.
1.3.6.1.4.1.171.10.75.16.1.33.2.1not-accessiblecurrent
cpuFilterL2RuleEntry
OBJECT-TYPE
Each entry in this table is a L2 filter rule. Index to the table is the L2 filter number and Profile ID.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1not-accessiblecurrent
cpuFilterL2ProfileID
OBJECT-TYPE
L2 Filter rule ID.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.1Integer32 (1..3)read-onlycurrent
cpuFilterL2AccessID
OBJECT-TYPE
CPUInterfaceFilter Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.2Integer32 (1..5)read-onlycurrent
cpuFilterL2RuleEtherType
OBJECT-TYPE
The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.3Integer32 (-1 | 1501..65535)read-writecurrent
cpuFilterL2RuleDstMacAddr
OBJECT-TYPE
Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.4MacAddressread-writecurrent
cpuFilterL2RuleSrcMacAddr
OBJECT-TYPE
Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.5MacAddressread-writecurrent
cpuFilterL2RuleVlanId
OBJECT-TYPE
Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.6Integer32 (-1..4094)read-writecurrent
cpuFilterL2Rule1pPriority
OBJECT-TYPE
802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.7Integer32 (-1..7)read-writecurrent
cpuFilterL2RuleDstMacAddrMask
OBJECT-TYPE
The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.8MacAddressread-onlycurrent
cpuFilterL2RuleSrcMacAddrMask
OBJECT-TYPE
The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.9MacAddressread-onlycurrent
cpuFilterL2RuleInPortList
OBJECT-TYPE
Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.10PortListread-writecurrent
cpuFilterL2RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.11INTEGER {allow(1), drop(2)}read-writecurrent
cpuFilterL2RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.33.2.1.1.14RowStatusread-createcurrent
cpuFilterL3Rule
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.33.3
cpuFilterL3RuleTable
OBJECT-TYPE
A table to configure L3 filter rules in the system.
1.3.6.1.4.1.171.10.75.16.1.33.3.1not-accessiblecurrent
cpuFilterL3RuleEntry
OBJECT-TYPE
Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1not-accessiblecurrent
cpuFilterL3RuleProfileNo
OBJECT-TYPE
L3 Filter rule ID.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.1Integer32 (1..5)read-onlycurrent
cpuFilterL3RuleAccessID
OBJECT-TYPE
The Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.2Integer32 (1..3)read-onlycurrent
cpuFilterL3RuleProtocol
OBJECT-TYPE
The type of protocol to be checked against the packet.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.3INTEGER {icmp(1), igmp(2), tcp(6), udp(17)}read-writecurrent
cpuFilterL3RuleProtocolMask
OBJECT-TYPE
The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.4OCTET STRINGread-onlycurrent
cpuFilterL3RuleICMPMessageType
OBJECT-TYPE
The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.5Integer32 (-1..255)read-writecurrent
cpuFilterL3RuleICMPMessageCode
OBJECT-TYPE
The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.6Integer32 (-1..255)read-writecurrent
cpuFilterL3RuleDstIpAddr
OBJECT-TYPE
Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.7IpAddressread-writecurrent
cpuFilterL3RuleSrcIpAddr
OBJECT-TYPE
Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.8IpAddressread-writecurrent
cpuFilterL3RuleDstIpAddrMask
OBJECT-TYPE
The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.9IpAddressread-onlycurrent
cpuFilterL3RuleSrcIpAddrMask
OBJECT-TYPE
The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.10IpAddressread-onlycurrent
cpuFilterL3RuleTcpUdpDstPort
OBJECT-TYPE
The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.11Integer32 (-1..65535)read-writecurrent
cpuFilterL3RuleTcpUdpSrcPort
OBJECT-TYPE
The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.12Integer32 (-1..65535)read-writecurrent
cpuFilterL3RuleTcpUdpDstPortMask
OBJECT-TYPE
The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.13OCTET STRINGread-onlycurrent
cpuFilterL3RuleTcpUdpSrcPortMask
OBJECT-TYPE
The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.14OCTET STRINGread-onlycurrent
cpuFilterL3RuleTcpAckBit
OBJECT-TYPE
The TCP ACK bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.15INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterL3RuleTcpRstBit
OBJECT-TYPE
The TCP RST bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.16INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterL3RuleTcpUrgBit
OBJECT-TYPE
The TCP Urg bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.17INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterL3RuleTcpPshBit
OBJECT-TYPE
The TCP Psh bit to be checked against the packet. The default value is 'dontcare'(-1). which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.18INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterL3RuleTcpSynBit
OBJECT-TYPE
The TCP Syn bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.19INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterL3RuleTcpFinBit
OBJECT-TYPE
The TCP Fin bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.20INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterL3RuleDscp
OBJECT-TYPE
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.21Integer32 (-1..63)read-createcurrent
cpuFilterL3RuleIgmpType
OBJECT-TYPE
The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.22Integer32 (-1..255)read-writecurrent
cpuFilterL3RulePortList
OBJECT-TYPE
Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.23PortListread-writecurrent
cpuFilterL3RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.24INTEGER {allow(1), drop(2)}read-writecurrent
cpuFilterL3RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.33.3.1.1.27RowStatusread-createcurrent
cpuFilterv6L3RuleTable
OBJECT-TYPE
A table to configure L3 filter rules in the system.
1.3.6.1.4.1.171.10.75.16.1.33.3.2not-accessiblecurrent
cpuFilterv6L3RuleEntry
OBJECT-TYPE
Each entry in this table is a L3 filter rule. Index to the table is L3 filter number and Profile ID.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1not-accessiblecurrent
cpuFilterv6L3RuleProfileNo
OBJECT-TYPE
L3 Filter rule ID.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.1Integer32 (1..5)read-onlycurrent
cpuFilterv6L3RuleAccessID
OBJECT-TYPE
The Profile ID which this rule join.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.2Integer32 (1..3)read-onlycurrent
cpuFilterv6L3RuleProtocol
OBJECT-TYPE
The type of protocol to be checked against the packet.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.3INTEGER {icmp(1), tcp(6), udp(17)}read-writecurrent
cpuFilterv6L3RuleProtocolMask
OBJECT-TYPE
The IP protocol mask. This field is read-only and copy from it's Profile setting. It will work with the other field,cpuFilterL3RuleProtocol, to caculate a range of IP protocol which is really care. The value is in HEX format.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.4OCTET STRINGread-onlycurrent
cpuFilterv6L3RuleICMPMessageType
OBJECT-TYPE
The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1',which means the rule don't care this condition. Some ICMP message types are: echoReply(0), destinationUnreachable(3), sourceQuench(4), redirect(5), echoRequest(8), timeExceeded(11), parameterProblem(12), timestampRequest(13), timestampReply(14), informationRequest(15), informationReply(16), addressMaskRequest(17), addressMaskReply (18),
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.5Integer32 (-1..255)read-writecurrent
cpuFilterv6L3RuleICMPMessageCode
OBJECT-TYPE
The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in cpuFilterL3RuleAction. The default value is '-1', which means the rule don't care this condition. Some ICMP message codes are : networkUnreachable(0), hostUnreachable(1), protocolUnreachable(2), portUnreachable(3), fragmentNeed(4), sourceRouteFail(5), destNetworkUnknown(6), destHostUnknown(7), srcHostIsolated(8), destNetworkAdminProhibited(9), destHostAdminProhibited(10), networkUnreachableTOS(11), hostUnreachableTOS(12),
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.6Integer32 (-1..255)read-writecurrent
cpuFilterv6L3RuleDstIpAddr
OBJECT-TYPE
Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.7Ipv6Addressread-writecurrent
cpuFilterv6L3RuleSrcIpAddr
OBJECT-TYPE
Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.8Ipv6Addressread-writecurrent
cpuFilterv6L3RuleDstIpAddrMask
OBJECT-TYPE
The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.9Ipv6Addressread-onlycurrent
cpuFilterv6L3RuleSrcIpAddrMask
OBJECT-TYPE
The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.10Ipv6Addressread-onlycurrent
cpuFilterv6L3RuleTcpUdpDstPort
OBJECT-TYPE
The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.11Integer32 (-1..65535)read-writecurrent
cpuFilterv6L3RuleTcpUdpSrcPort
OBJECT-TYPE
The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.12Integer32 (-1..65535)read-writecurrent
cpuFilterv6L3RuleTcpUdpDstPortMask
OBJECT-TYPE
The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.13OCTET STRINGread-onlycurrent
cpuFilterv6L3RuleTcpUdpSrcPortMask
OBJECT-TYPE
The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.14OCTET STRINGread-onlycurrent
cpuFilterv6L3RuleTcpAckBit
OBJECT-TYPE
The TCP ACK bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.15INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterv6L3RuleTcpRstBit
OBJECT-TYPE
The TCP RST bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.16INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterv6L3RuleTcpUrgBit
OBJECT-TYPE
The TCP Urg bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.17INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterv6L3RuleTcpPshBit
OBJECT-TYPE
The TCP Psh bit to be checked against the packet. The default value is 'dontcare'(-1). which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.18INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterv6L3RuleTcpSynBit
OBJECT-TYPE
The TCP Syn bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.19INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterv6L3RuleTcpFinBit
OBJECT-TYPE
The TCP Fin bit to be checked against the packet. The default value is 'dontcare'(-1), which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.20INTEGER {dontcare(-1), establish(1), notEstablish(2)}read-createcurrent
cpuFilterv6L3RuleTrafficClass
OBJECT-TYPE
The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.21Integer32 (-1..63)read-createcurrent
cpuFilterv6L3RulePortList
OBJECT-TYPE
Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.22PortListread-writecurrent
cpuFilterv6L3RuleAction
OBJECT-TYPE
Specifies the action to be taken on the packet if the filter rule matches.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.23INTEGER {allow(1), drop(2)}read-writecurrent
cpuFilterv6L3RuleStatus
OBJECT-TYPE
This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'.
1.3.6.1.4.1.171.10.75.16.1.33.3.2.1.24RowStatusread-createcurrent
companyStaticARP
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.34
staticARPTable
OBJECT-TYPE
A list of the Static MACs
1.3.6.1.4.1.171.10.75.16.1.34.2not-accessiblecurrent
staticARPEntry
OBJECT-TYPE
A Static MAC entry containing the mac and forwarding port.
1.3.6.1.4.1.171.10.75.16.1.34.2.1not-accessiblecurrent
staticARPIP
OBJECT-TYPE
The VLAN ID of the static ARP IP.
1.3.6.1.4.1.171.10.75.16.1.34.2.1.2IpAddressread-onlycurrent
staticARPMac
OBJECT-TYPE
The MAC address associated of the static ARP entry.
1.3.6.1.4.1.171.10.75.16.1.34.2.1.3MacAddressread-onlycurrent
staticARPRowStatus
OBJECT-TYPE
The status of an entry in the Static ARP Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static ARP.
1.3.6.1.4.1.171.10.75.16.1.34.2.1.5RowStatusread-writecurrent
companyCableDiagnostic
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.35
cableDiagTable
OBJECT-TYPE
A table that contains the cable situation for each port.
1.3.6.1.4.1.171.10.75.16.1.35.1not-accessiblecurrent
cableDiagEntry
OBJECT-TYPE
A list of cable situations for each port on the device.
1.3.6.1.4.1.171.10.75.16.1.35.1.1not-accessiblecurrent
cableDiagPortIndex
OBJECT-TYPE
The interface index for which the configuration in this entry applies. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.1Integer32 (1..26)read-onlycurrent
cableDiagPortType
OBJECT-TYPE
Indicates the supported port data rate classification.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.2INTEGER {fastEthernet(0), gigaEthernet(1), other(2)}read-onlycurrent
cableDiagLinkStatus
OBJECT-TYPE
This object indicates the link status.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.3INTEGER {linkdown(0), linkup(1), other(2)}read-onlycurrent
cableDiagPair1Status
OBJECT-TYPE
Cable diagnostics pair 1 test result.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.4INTEGER {ok(0), open(1), short(2), open-short(3), crosstalk(4), unknown(5), count(6), no-cable(7), other(8)}read-onlycurrent
cableDiagPair2Status
OBJECT-TYPE
Cable diagnostics pair 2 test result.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.5INTEGER {ok(0), open(1), short(2), open-short(3), crosstalk(4), unknown(5), count(6), no-cable(7), other(8)}read-onlycurrent
cableDiagPair3Status
OBJECT-TYPE
Cable diagnostics pair 3 test result.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.6INTEGER {ok(0), open(1), short(2), open-short(3), crosstalk(4), unknown(5), count(6), no-cable(7), other(8)}read-onlycurrent
cableDiagPair4Status
OBJECT-TYPE
Cable diagnostics pair 4 test result.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.7INTEGER {ok(0), open(1), short(2), open-short(3), crosstalk(4), unknown(5), count(6), no-cable(7), other(8)}read-onlycurrent
cableDiagPair1Length
OBJECT-TYPE
Cable Diagnostics pair 1 fault distance.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.8Integer32read-onlycurrent
cableDiagPair2Length
OBJECT-TYPE
Cable diagnostics pair 2 fault distance.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.9Integer32read-onlycurrent
cableDiagPair3Length
OBJECT-TYPE
Cable diagnostics pair 3 fault distance.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.10Integer32read-onlycurrent
cableDiagPair4Length
OBJECT-TYPE
Cable diagnostics pair 4 fault distance.
1.3.6.1.4.1.171.10.75.16.1.35.1.1.11Integer32read-onlycurrent
cableDiagAction
OBJECT-TYPE
Function to run the cable diagnostic on selected port. Can not detect fiber ports
1.3.6.1.4.1.171.10.75.16.1.35.1.1.12INTEGER {action(1), processing(2), other(3)}read-writecurrent
cableDiagStatus
OBJECT-TYPE
Indicates the status of cable diagnostics on the port. not-run - cable diagnostics has never been run for this port processing - cable diagnostics is currently running on the port last-test-ok - the last cable diagnostics done on the port was successful last-test-failed - the last cable diagnostics done on the port failed
1.3.6.1.4.1.171.10.75.16.1.35.1.1.13INTEGER {notrun(1), processing(2), lasttestok(3), lasttestfailed(4)}read-onlycurrent
companyVLANTrunk
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.36
vlanTrunkSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.36.1
vlanTrunkGlobalStatus
OBJECT-TYPE
This indicates the global state of the VLAN trunking feature of the device.
1.3.6.1.4.1.171.10.75.16.1.36.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
vlanTrunkTable
OBJECT-TYPE
This table is used to manage the VLAN trunking feature of the device.
1.3.6.1.4.1.171.10.75.16.1.36.1.2not-accessiblecurrent
vlanTrunkEntry
OBJECT-TYPE
There is one entry in this table for each created port-channel port.
1.3.6.1.4.1.171.10.75.16.1.36.1.2.1not-accessiblecurrent
vlanTrunkIfIndex
OBJECT-TYPE
The index of the port.
1.3.6.1.4.1.171.10.75.16.1.36.1.2.1.1InterfaceIndexread-onlycurrent
vlanTrunkState
OBJECT-TYPE
Sets the VLAN trunk status as enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.36.1.2.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
companyQinQ
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.37
qinqSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.37.1
qinqGlobalStatus
OBJECT-TYPE
This object is used to enable/disable the Q-in-Q status.
1.3.6.1.4.1.171.10.75.16.1.37.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
qinqTable
OBJECT-TYPE
A table that contains Q-in-Q VLAN mode information about each port.
1.3.6.1.4.1.171.10.75.16.1.37.1.2not-accessiblecurrent
qinqEntry
OBJECT-TYPE
A list of Q-in-Q VLAN mode information for each port.
1.3.6.1.4.1.171.10.75.16.1.37.1.2.1not-accessiblecurrent
qinqIfIndex
OBJECT-TYPE
The index of the port.
1.3.6.1.4.1.171.10.75.16.1.37.1.2.1.1InterfaceIndexread-onlycurrent
qinqRoleState
OBJECT-TYPE
Sets the QinQ Role as NNI or UNI.
1.3.6.1.4.1.171.10.75.16.1.37.1.2.1.2INTEGER {nni(1), uni(2)}read-writecurrent
qinqOuterTPID
OBJECT-TYPE
Sets the QinQ Outer TPID value.
1.3.6.1.4.1.171.10.75.16.1.37.1.2.1.3Unsigned32read-writecurrent
qinqTrustCVIDState
OBJECT-TYPE
Sets the QinQ Trust CVID state as enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.37.1.2.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
qinqVLANTranslationState
OBJECT-TYPE
Sets the QinQ VLANTranslation state as enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.37.1.2.1.5INTEGER {enabled(1), disabled(2)}read-writecurrent
qinqVLANTranslation
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.37.2
qinqVlanTranslationCVIDTable
OBJECT-TYPE
A table that contains VLAN translation information applied in enabling port's swQinQPortVlanTranslation, swQinQPortTrustCVID and QinQ.
1.3.6.1.4.1.171.10.75.16.1.37.2.1not-accessiblecurrent
qinqVlanTranslationCVIDEntry
OBJECT-TYPE
A list of VLAN translation information applied in enabling a port's swQinQPortVlanTranslation, swQinQPortTrustCVID and QinQ.
1.3.6.1.4.1.171.10.75.16.1.37.2.1.1not-accessiblecurrent
qinqVlanTranslationCVID
OBJECT-TYPE
The customer VLAN identifier in a C-TAG.
1.3.6.1.4.1.171.10.75.16.1.37.2.1.1.1Unsigned32read-onlycurrent
qinqVlanTranslationSVID
OBJECT-TYPE
A VLAN identifier conveyed in an S-TAG.
1.3.6.1.4.1.171.10.75.16.1.37.2.1.1.2Unsigned32read-createcurrent
qinqVlanTranslationSVIDOperation
OBJECT-TYPE
The 'add' action indicates to add a tag for the assigned SP-VLAN before the C-VLAN tag. If there is S-TAG in the packet, this rule will not take effect. The 'replace' action indicates to replace the C-VLAN in the tag by the SP-VLAN. If there is no C-TAG in the packet, this rule will not take effect.
1.3.6.1.4.1.171.10.75.16.1.37.2.1.1.3INTEGER {add(1), replace(2)}read-createcurrent
qinqVlanTranslationCVIDRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.37.2.1.1.4RowStatusread-createcurrent
companyTimeRangeMgmt
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.38
swTimeRangeSettingTable
OBJECT-TYPE
A table to configure time Range in the system.
1.3.6.1.4.1.171.10.75.16.1.38.1not-accessiblecurrent
swTimeRangeSettingEntry
OBJECT-TYPE
A schedule entry to configure time Range in the system.
1.3.6.1.4.1.171.10.75.16.1.38.1.1not-accessiblecurrent
swTimeRangeIndex
OBJECT-TYPE
The Time Range identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 52.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.1Integer32 (1..52)read-onlycurrent
swTimeRangeName
OBJECT-TYPE
The Schedule name associated with the Schedule entry (e.g., `abc, bbb').
1.3.6.1.4.1.171.10.75.16.1.38.1.1.2DisplayString (SIZE(1..20))read-writecurrent
swTimeRangeDate
OBJECT-TYPE
Enable/Disable date range checking while executing time base PoE.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.3INTEGER {enabled(1), disabled(2)}read-writecurrent
swTimeRangeStartYear
OBJECT-TYPE
Start year of the Schedule entry.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.4INTEGER {y2009(2009), y2010(2010), y2011(2011), y2012(2012), y2013(2013), y2014(2014), y2015(2015), y2016(2016), y2017(2017), y2018(2018), y2019(2019), y2020(2020), y2021(2021), y2022(2022), y2023(2023), y2024(2024), y2025(2025), y2026(2026), y2027(2027), y2028(2028), y2029(2029), y2030(2030), y2031(2031), y2032(2032), y2033(2033), y2034(2034), y2035(2035), y2036(2036), y2037(2037)}read-writecurrent
swTimeRangeStartMonth
OBJECT-TYPE
Start month of the Schedule entry.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.5INTEGER {january(1), february(2), march(3), april(4), may(5), june(6), july(7), august(8), september(9), october(10), november(11), december(12)}read-writecurrent
swTimeRangeStartDay
OBJECT-TYPE
Start day of the Schedule entry. The value must be from 1 to 31.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.6Integer32 (1..31)read-writecurrent
swTimeRangeStartHour
OBJECT-TYPE
Start hour of the Schedule entry. The value must be from 0 to 23.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.7Integer32 (0..23)read-writecurrent
swTimeRangeStartMinute
OBJECT-TYPE
Start minute of the Schedule entry. The value must be from 0 to 59.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.8Integer32 (0..59)read-writecurrent
swTimeRangeEndYear
OBJECT-TYPE
End year of the Schedule entry.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.9INTEGER {y2009(2009), y2010(2010), y2011(2011), y2012(2012), y2013(2013), y2014(2014), y2015(2015), y2016(2016), y2017(2017), y2018(2018), y2019(2019), y2020(2020), y2021(2021), y2022(2022), y2023(2023), y2024(2024), y2025(2025), y2026(2026), y2027(2027), y2028(2028), y2029(2029), y2030(2030), y2031(2031), y2032(2032), y2033(2033), y2034(2034), y2035(2035), y2036(2036), y2037(2037)}read-writecurrent
swTimeRangeEndMonth
OBJECT-TYPE
End month of the Schedule entry.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.10INTEGER {january(1), february(2), march(3), april(4), may(5), june(6), july(7), august(8), september(9), october(10), november(11), december(12)}read-writecurrent
swTimeRangeEndDay
OBJECT-TYPE
End day of the Schedule entry. The value must be from 1 to 31.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.11Integer32 (1..31)read-writecurrent
swTimeRangeEndHour
OBJECT-TYPE
End hour of the Schedule entry. The value must be from 0 to 23.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.12Integer32 (0..23)read-writecurrent
swTimeRangeEndMinute
OBJECT-TYPE
End minute of the Schedule entry. The value must be from 0 to 59.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.13Integer32 (0..59)read-writecurrent
swTimeRangeMonday
OBJECT-TYPE
Enable/Disble scheduling Monday.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.14INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeTuesday
OBJECT-TYPE
Enable/Disble scheduling Tuesday.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.15INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeWednesday
OBJECT-TYPE
Enable/Disble scheduling Wednesday.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.16INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeThursday
OBJECT-TYPE
Enable/Disble scheduling Thursday.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.17INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeFriday
OBJECT-TYPE
Enable/Disble scheduling Friday.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.18INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeSaturday
OBJECT-TYPE
Enable/Disble scheduling Saturday.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.19INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeSunday
OBJECT-TYPE
Enable/Disble scheduling Sunday.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.20INTEGER {enable(1), disable(2)}read-writecurrent
swTimeRangeRowStatus
OBJECT-TYPE
The status of an entry in the Time Range Information Table. Only a subset of the rowstatus variables (active, notinservice, createAndWait, destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.38.1.1.21RowStatusread-createcurrent
companySMTP
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.40
ipv4smtpState
OBJECT-TYPE
Enable or Disable SMTP function.
1.3.6.1.4.1.171.10.75.16.1.40.1INTEGER {disabled(0), enabled(1)}read-writeobsolete
ipv4smtpServerAddr
OBJECT-TYPE
SMTP Server's IP Address
1.3.6.1.4.1.171.10.75.16.1.40.2IpAddressread-writeobsolete
ipv4smtpServerPort
OBJECT-TYPE
SMTP Server's port
1.3.6.1.4.1.171.10.75.16.1.40.3INTEGERread-writeobsolete
ipv4smtpSelfMailAddr
OBJECT-TYPE
The sender's (DUT) mail address .
1.3.6.1.4.1.171.10.75.16.1.40.4OCTET STRINGread-writeobsolete
ipv4smtpRecvMailAddrTable
OBJECT-TYPE
Receivers' mail address table.
1.3.6.1.4.1.171.10.75.16.1.40.5not-accessiblecurrent
ipv4smtpRecvMailAddrEntry
OBJECT-TYPE
Receivers' mail address entry.
1.3.6.1.4.1.171.10.75.16.1.40.5.1not-accessiblecurrent
ipv4smtpRecvMailAddrIndex
OBJECT-TYPE
Receivers' mail address index (1~8).
1.3.6.1.4.1.171.10.75.16.1.40.5.1.1INTEGER (1..8)read-onlycurrent
ipv4smtpRecvMailAddr
OBJECT-TYPE
Receivers' mail address.
1.3.6.1.4.1.171.10.75.16.1.40.5.1.2OCTET STRINGread-writecurrent
ipv4smtpRecvMailAddrStatus
OBJECT-TYPE
Rowstatus of the receiver's mail address.
1.3.6.1.4.1.171.10.75.16.1.40.5.1.3RowStatusread-writecurrent
sysSMTPServerGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.40.6
smtpState
OBJECT-TYPE
Enable or Disable SMTP function.
1.3.6.1.4.1.171.10.75.16.1.40.6.1INTEGER {disabled(0), enabled(1)}read-writecurrent
smtpServerAddr
OBJECT-TYPE
SMTP Server's IP Address
1.3.6.1.4.1.171.10.75.16.1.40.6.2Ipv6Addressread-writecurrent
smtpServerAddrType
OBJECT-TYPE
SMTP Server's Address type.
1.3.6.1.4.1.171.10.75.16.1.40.6.3INTEGER {iPv4(1), iPv6(2)}read-writecurrent
smtpServerAddrInterfaceName
OBJECT-TYPE
Specifies the interface name when the smtpServerAddrInterfaceName is linklocal address.
1.3.6.1.4.1.171.10.75.16.1.40.6.4OCTET STRINGread-writecurrent
smtpServerPort
OBJECT-TYPE
SMTP Server's port
1.3.6.1.4.1.171.10.75.16.1.40.6.5INTEGERread-writecurrent
smtpSelfMailAddr
OBJECT-TYPE
The sender's (DUT) mail address .
1.3.6.1.4.1.171.10.75.16.1.40.6.6OCTET STRINGread-writecurrent
smtpRecvMailAddrTable
OBJECT-TYPE
Receivers' mail address table.
1.3.6.1.4.1.171.10.75.16.1.40.6.7not-accessiblecurrent
smtpRecvMailAddrEntry
OBJECT-TYPE
Receivers' mail address entry.
1.3.6.1.4.1.171.10.75.16.1.40.6.7.1not-accessiblecurrent
smtpRecvMailAddrIndex
OBJECT-TYPE
Receivers' mail address index (1~8).
1.3.6.1.4.1.171.10.75.16.1.40.6.7.1.1INTEGER (1..8)read-onlycurrent
smtpRecvMailAddr
OBJECT-TYPE
Receivers' mail address.
1.3.6.1.4.1.171.10.75.16.1.40.6.7.1.2OCTET STRINGread-writecurrent
smtpRecvMailAddrStatus
OBJECT-TYPE
Rowstatus of the receiver's mail address.
1.3.6.1.4.1.171.10.75.16.1.40.6.7.1.3RowStatusread-writecurrent
companyLimitIp
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.45
limitIpMulticastProfileTable
OBJECT-TYPE
A list of the limit ip multicast Profile Table.
1.3.6.1.4.1.171.10.75.16.1.45.1not-accessiblecurrent
limitIpMulticastProfileEntry
OBJECT-TYPE
A limit ip multicast entry maintain by the start IP Address, end ip address, profile id.
1.3.6.1.4.1.171.10.75.16.1.45.1.1not-accessiblecurrent
limitIpMulticastIPType
OBJECT-TYPE
Indicate the IP type of profile.
1.3.6.1.4.1.171.10.75.16.1.45.1.1.1INTEGER {ipv4(1), ipv6(2)}read-onlycurrent
limitIpMulticastProfileID
OBJECT-TYPE
The ProfileID of the limit ip multicast profile entry.
1.3.6.1.4.1.171.10.75.16.1.45.1.1.2INTEGER (1..24)read-onlycurrent
limitIpMulticastProfileName
OBJECT-TYPE
The ProfileName of the limit ip multicast profile entry.
1.3.6.1.4.1.171.10.75.16.1.45.1.1.3DisplayString (SIZE(1..20))read-writecurrent
limitIpMulticastProfileStatus
OBJECT-TYPE
The status of an entry in the limit ip multicast profile Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.45.1.1.4RowStatusread-writecurrent
limitIpMulticastEntryTable
OBJECT-TYPE
A list of the limit ip multicast entry Table.
1.3.6.1.4.1.171.10.75.16.1.45.2not-accessiblecurrent
limitIpMulticastEntry
OBJECT-TYPE
A limit ip multicast entry maintain by the start IP Address, end ip address, profile id.
1.3.6.1.4.1.171.10.75.16.1.45.2.1not-accessiblecurrent
limitIpMulticastEntryIPType
OBJECT-TYPE
Indicate the IP type of entry.
1.3.6.1.4.1.171.10.75.16.1.45.2.1.1INTEGER {ipv4(1), ipv6(2)}read-onlycurrent
limitIpMulticastEntryProfileID
OBJECT-TYPE
The ProfileID of the limit ip multicast entry.
1.3.6.1.4.1.171.10.75.16.1.45.2.1.2INTEGER (1..24)read-onlycurrent
limitIpMulticaststartIpAddr
OBJECT-TYPE
The limit ip multicast IP address is used to set start ip
1.3.6.1.4.1.171.10.75.16.1.45.2.1.3DisplayString (SIZE(1..16))read-onlycurrent
limitIpMulticastendIpAddr
OBJECT-TYPE
The limit ip multicast IP address is used to set end ip
1.3.6.1.4.1.171.10.75.16.1.45.2.1.4DisplayString (SIZE(1..16))read-onlycurrent
limitIpMulticastStatus
OBJECT-TYPE
The status of an entry in the limit ip multicast entry Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.45.2.1.5RowStatusread-writecurrent
limitIpMulticastPortTable
OBJECT-TYPE
A list of the limit ip multicast Port entry Table.
1.3.6.1.4.1.171.10.75.16.1.45.3not-accessiblecurrent
limitIpMulticastPortEntry
OBJECT-TYPE
A limit ip multicast entry maintain by the Port Index.
1.3.6.1.4.1.171.10.75.16.1.45.3.1not-accessiblecurrent
limitIpMulticastPortIPType
OBJECT-TYPE
Indicate the IP type of entry.
1.3.6.1.4.1.171.10.75.16.1.45.3.1.1INTEGER {ipv4(1), ipv6(2)}read-onlycurrent
limitIpMulticastPortID
OBJECT-TYPE
The Port Index of the limit ip multicast port entry. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.45.3.1.2INTEGER (1..26)read-onlycurrent
limitIpMulticastPortState
OBJECT-TYPE
The limit ip multicast port state
1.3.6.1.4.1.171.10.75.16.1.45.3.1.3INTEGER {permit(1), deny(2)}read-writecurrent
limitIpMulticastPortProfileID
OBJECT-TYPE
The limit ip multicast port mapping profileID list.
1.3.6.1.4.1.171.10.75.16.1.45.3.1.4PortListread-writecurrent
limitIpMulticastPortMaxGrp
OBJECT-TYPE
The limit ip multicast per-port max group.
1.3.6.1.4.1.171.10.75.16.1.45.3.1.5INTEGER (1..256)read-writecurrent
companyGratuitousARP
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.48
sysGratuitousARPGlobalSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.48.1
sysGratuitousARPIPIfStatusUp
OBJECT-TYPE
This object indicates Send On IP Interface Status Up is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.48.1.1INTEGER {enable(1), disable(2)}read-writecurrent
sysGratuitousARPDuplicateIPDetected
OBJECT-TYPE
This object indicates Send On Duplicate IP Detected is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.48.1.2INTEGER {enable(1), disable(2)}read-writecurrent
sysGratuitousARPLearning
OBJECT-TYPE
This object indicates Gratuitous ARP Learning is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.48.1.3INTEGER {enable(1), disable(2)}read-writecurrent
sysGratuitousARPSettings
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.48.2
sysGratuitousARPTable
OBJECT-TYPE
Set/Add Gratuitous ARP interface name and interval time.
1.3.6.1.4.1.171.10.75.16.1.48.2.1not-accessiblecurrent
sysGratuitousARPEntry
OBJECT-TYPE
The entry of gratuitous ARP!
1.3.6.1.4.1.171.10.75.16.1.48.2.1.1not-accessiblecurrent
sysGratuitousARPIFName
OBJECT-TYPE
Interface name.
1.3.6.1.4.1.171.10.75.16.1.48.2.1.1.1OCTET STRING (SIZE(1..24))read-onlycurrent
sysGratuitousARPInterval
OBJECT-TYPE
Gratuitous ARP interval time for each interface.
1.3.6.1.4.1.171.10.75.16.1.48.2.1.1.2Integer32 (0..65535)read-writecurrent
companyMulticastFilter
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.49
mcastFilterPortTable
OBJECT-TYPE
A table to control multicast filtering modes.
1.3.6.1.4.1.171.10.75.16.1.49.1not-accessiblecurrent
mcastFilterPortEntry
OBJECT-TYPE
An entry appears in this table for each interface in the mcastFiltertem. Index to the table is the interface index of the port.
1.3.6.1.4.1.171.10.75.16.1.49.1.1not-accessiblecurrent
mcastFilterPortIndex
OBJECT-TYPE
Interface index of the port for which the configuration in this entry applies. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.49.1.1.1Integer32 (1..26)not-accessiblecurrent
mcastFilterPortType
OBJECT-TYPE
Configures the multicast filtering modes as below : forward -Forwards all unregistered groups. filter -Filters all unregistered groups.
1.3.6.1.4.1.171.10.75.16.1.49.1.1.2INTEGER {forward(1), filter(2)}read-writecurrent
companyNeighbor
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.50
neighborTable
OBJECT-TYPE
A list of the Neighbor Cache Table.
1.3.6.1.4.1.171.10.75.16.1.50.1not-accessiblecurrent
neighborEntry
OBJECT-TYPE
A Neighbor cache entry containing the ifindex and ipv6 addr.
1.3.6.1.4.1.171.10.75.16.1.50.1.1not-accessiblecurrent
neighborIfindex
OBJECT-TYPE
The interface index of the Neighbor entry. Must be conform to the existing interface name.
1.3.6.1.4.1.171.10.75.16.1.50.1.1.1INTEGER (1..255)read-onlycurrent
neighborIPv6Addr
OBJECT-TYPE
Allows the entry of an IP address that will be a Neighbor entry into the Neighbor Cache Table.
1.3.6.1.4.1.171.10.75.16.1.50.1.1.2Ipv6Addressread-onlycurrent
neighborMACAddr
OBJECT-TYPE
The MAC address associated of the Neighbor entry.
1.3.6.1.4.1.171.10.75.16.1.50.1.1.3MacAddressread-onlycurrent
neighborType
OBJECT-TYPE
The type associated of the Neighbor entry.
1.3.6.1.4.1.171.10.75.16.1.50.1.1.4INTEGER {static(1), dynamic(2)}read-onlycurrent
neighborCacheState
OBJECT-TYPE
The type associated of the Neighbor entry.
1.3.6.1.4.1.171.10.75.16.1.50.1.1.5INTEGER {static(1), reachable(2), incomplete(3), stale(4), delay(5), probe(6), notinservice(7)}read-onlycurrent
neighborActiveStatus
OBJECT-TYPE
The active status of the Neighbor entry.
1.3.6.1.4.1.171.10.75.16.1.50.1.1.6INTEGER {active(1), inactive(2)}read-onlycurrent
neighborRowStatus
OBJECT-TYPE
The status of an entry in the Neighbor Cache Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.
1.3.6.1.4.1.171.10.75.16.1.50.1.1.7RowStatusread-writecurrent
companyEoam
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.51
eoamSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.51.1
eoamTable
OBJECT-TYPE
A table that contains EOAM mode information about each port.
1.3.6.1.4.1.171.10.75.16.1.51.1.2not-accessiblecurrent
eoamEntry
OBJECT-TYPE
A list of EOAM mode information for each port.
1.3.6.1.4.1.171.10.75.16.1.51.1.2.1not-accessiblecurrent
eoamIfIndex
OBJECT-TYPE
The index of the port.
1.3.6.1.4.1.171.10.75.16.1.51.1.2.1.1InterfaceIndexread-onlycurrent
eoamState
OBJECT-TYPE
Sets the EOAM state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.51.1.2.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
eoamMode
OBJECT-TYPE
Sets the EOAM mode as active or passive.
1.3.6.1.4.1.171.10.75.16.1.51.1.2.1.3INTEGER {passive(1), active(2)}read-writecurrent
eoamReceivedRemoteLoopback
OBJECT-TYPE
Sets the EOAM received or ignore remote loopback packets.
1.3.6.1.4.1.171.10.75.16.1.51.1.2.1.4INTEGER {ignore(1), process(2)}read-writecurrent
eoamRemoteLoopback
OBJECT-TYPE
Sets the EOAM remote loopback start or stop.
1.3.6.1.4.1.171.10.75.16.1.51.1.2.1.5INTEGER {noLoopBack(1), startLoopBack(2), remoteLoopBack(3), stopLoopBack(4), localLoopBack(5), unknownLoopBack(6)}read-writecurrent
eoamDyingGaspEnable
OBJECT-TYPE
Sets the EOAM dying gasp state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.51.1.2.1.6INTEGER {enabled(1), disabled(2)}read-writecurrent
eoamCriticalEventEnable
OBJECT-TYPE
Sets the EOAM critical event state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.51.1.2.1.7INTEGER {enabled(1), disabled(2)}read-writecurrent
eoamLinkMonitor
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.51.2
eoamLinkMonitorTable
OBJECT-TYPE
A table that contains EOAM link monitor information about each port.
1.3.6.1.4.1.171.10.75.16.1.51.2.1not-accessiblecurrent
eoamLinkMonitorEntry
OBJECT-TYPE
A list of EOAM link monitor information for each port.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1not-accessiblecurrent
eoamLinkMonitorIfIndex
OBJECT-TYPE
The index of the port.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.1InterfaceIndexread-onlycurrent
errorSymbolNotifyState
OBJECT-TYPE
Sets the EOAM error symbol notify state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
errorSymbolThreshold
OBJECT-TYPE
Sets the EOAM error symbol threshold.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.3Unsigned32read-writecurrent
errorSymbolWindow
OBJECT-TYPE
Sets the EOAM error symbol window.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.4Unsigned32read-writecurrent
errorFrameNotifyState
OBJECT-TYPE
Sets the EOAM error frame notify state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.5INTEGER {enabled(1), disabled(2)}read-writecurrent
errorFrameThreshold
OBJECT-TYPE
Sets the EOAM error frame threshold.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.6Unsigned32read-writecurrent
errorFrameWindow
OBJECT-TYPE
Sets the EOAM error symbol window.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.7Unsigned32read-writecurrent
errorFrameSecondsNotifyState
OBJECT-TYPE
Sets the EOAM error symbol notify state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
errorFrameSecondsThreshold
OBJECT-TYPE
Sets the EOAM error symbol threshold.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.9Unsigned32read-writecurrent
errorFrameSecondsWindow
OBJECT-TYPE
Sets the EOAM error symbol window.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.10Unsigned32read-writecurrent
errorFramePeriodNotifyState
OBJECT-TYPE
Sets the EOAM error symbol notify state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.11INTEGER {enabled(1), disabled(2)}read-writecurrent
errorFramePeriodThreshold
OBJECT-TYPE
Sets the EOAM error symbol threshold.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.12Unsigned32read-writecurrent
errorFramePeriodWindow
OBJECT-TYPE
Sets the EOAM error symbol window.
1.3.6.1.4.1.171.10.75.16.1.51.2.1.1.13Unsigned32read-writecurrent
companyDuld
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.52
duldSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.52.1
duldTable
OBJECT-TYPE
A table that contains DULD mode information about each port.
1.3.6.1.4.1.171.10.75.16.1.52.1.1not-accessiblecurrent
duldEntry
OBJECT-TYPE
A list of DULD mode information for each port.
1.3.6.1.4.1.171.10.75.16.1.52.1.1.1not-accessiblecurrent
duldIfIndex
OBJECT-TYPE
The index of the port.
1.3.6.1.4.1.171.10.75.16.1.52.1.1.1.1InterfaceIndexread-onlycurrent
duldState
OBJECT-TYPE
Sets the DULD admin state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.52.1.1.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
duldOperState
OBJECT-TYPE
Gets the DULD Oper state enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.52.1.1.1.3INTEGER {enabled(1), disabled(2)}read-onlycurrent
duldMode
OBJECT-TYPE
Sets the DULD mode as shutdown or normal.
1.3.6.1.4.1.171.10.75.16.1.52.1.1.1.4INTEGER {shutdown(1), normal(2)}read-writecurrent
duldLinkStatus
OBJECT-TYPE
Gets the DULD link status.
1.3.6.1.4.1.171.10.75.16.1.52.1.1.1.5INTEGER {unknow(1), bidirectional(2), txFault(3), rxFault(4), linkDown(5)}read-onlycurrent
duldDiscoveryTime
OBJECT-TYPE
Sets the DULD discovery time.
1.3.6.1.4.1.171.10.75.16.1.52.1.1.1.6Unsigned32 (5..65535)read-writecurrent
duldRecoverTime
OBJECT-TYPE
Duld auto recover time.
1.3.6.1.4.1.171.10.75.16.1.52.1.2Unsigned32 (0 | 60..1000000)read-writecurrent
companyMacBasedVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.70
macBasedVlanTable
OBJECT-TYPE
A table that contains information on Vlan-MAC address mapping.
1.3.6.1.4.1.171.10.75.16.1.70.1not-accessiblecurrent
macBasedVlanEntry
OBJECT-TYPE
Entry that contains Vlan-MAC address mapping.
1.3.6.1.4.1.171.10.75.16.1.70.1.1not-accessiblecurrent
vlanMacMapIndex
OBJECT-TYPE
Index of cmMacBasedVlanEntry. This object indicates the mac vlan entry for which the configurations in cmMacBasedVlanEntry is to be done.
1.3.6.1.4.1.171.10.75.16.1.70.1.1.1Integer32 (1..128)read-onlycurrent
vlanMacMapAddr
OBJECT-TYPE
The Mac address for which the Vlan mapping is present in the entry.
1.3.6.1.4.1.171.10.75.16.1.70.1.1.2MacAddressread-writecurrent
vlanMacMapAddrMask
OBJECT-TYPE
The Mac address for which the Vlan mapping is present in the entry.
1.3.6.1.4.1.171.10.75.16.1.70.1.1.3MacAddressread-writecurrent
vlanMacMapVid
OBJECT-TYPE
The Vlan to which the mac address of this entry is mapped to.
1.3.6.1.4.1.171.10.75.16.1.70.1.1.4VlanIndexread-writecurrent
vlanMacStatus
OBJECT-TYPE
The status given to the mac-vlan entry.
1.3.6.1.4.1.171.10.75.16.1.70.1.1.5DisplayStringread-onlycurrent
vlanMacType
OBJECT-TYPE
The type given to the mac-vlan entry.
1.3.6.1.4.1.171.10.75.16.1.70.1.1.6DisplayStringread-onlycurrent
vlanMacMapRowStatus
OBJECT-TYPE
The row status of the entry.
1.3.6.1.4.1.171.10.75.16.1.70.1.1.99RowStatusread-writecurrent
macBasedVlanMethod
OBJECT-TYPE
A method of Vlan-MAC address mapping.
1.3.6.1.4.1.171.10.75.16.1.70.2INTEGER {single(1), range(2)}read-writecurrent
companyBPDUAttack
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.77
sysBPDUAttackStateEnable
OBJECT-TYPE
Use this to enable BPDU attack protection. The BPDU Attack Protection function and Spanning Tree Protocol for ports are mutually exclusive. When the STP function is enabled on a particular port, BPDU Attack Protection cannot be enabled.
1.3.6.1.4.1.171.10.75.16.1.77.1INTEGER {enabled(1), disabled(2)}read-writecurrent
sysBPDUAttackRecoverTime
OBJECT-TYPE
When a port enters under attack state, it can be disabled or blocked based on the configuration. The state can be recovered manually or by the auto recovery mechanism. This command is used to configure the auto-recovery timer. To manually recover the port, the user needs to disable and re-enable the port.
1.3.6.1.4.1.171.10.75.16.1.77.2Integer32 (0 | 60..1000000)read-writecurrent
sysBPDUAttackCtrlTable
OBJECT-TYPE
A table to control BPDU Attack features either for the entire switch or for each interface in the switch.
1.3.6.1.4.1.171.10.75.16.1.77.3not-accessiblecurrent
sysBPDUAttackCtrlEntry
OBJECT-TYPE
An entry appears in this table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.77.3.1not-accessiblecurrent
sysBPDUAttackCtrlIndex
OBJECT-TYPE
The interface index of the port for which the configuration in this entry applies. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.77.3.1.1Integer32 (1..26)read-onlycurrent
sysBPDUAttackPortState
OBJECT-TYPE
Used to configure the BPDU Attack Protection state of a port. The default state is disable.
1.3.6.1.4.1.171.10.75.16.1.77.3.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
sysBPDUAttackPortMode
OBJECT-TYPE
Used to configure the BPDU Attack Protection mode of a port.
1.3.6.1.4.1.171.10.75.16.1.77.3.1.3INTEGER {drop(1), block(2), shutdown(3)}read-writecurrent
sysBPDUAttackPortStatus
OBJECT-TYPE
Use this to view per port BPDU attack protection status.
1.3.6.1.4.1.171.10.75.16.1.77.3.1.4INTEGER {normal(1), underAttack(2)}read-onlycurrent
sysBPDUAttackLog
OBJECT-TYPE
Used to configure log settings for BPDU attack protection events.
1.3.6.1.4.1.171.10.75.16.1.77.4INTEGER {none(1), attackDetected(2), attackCleared(3), both(4)}read-writecurrent
companyDHCPv6Relay
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.86
dhcpv6RelayControl
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.86.1
dhcpv6RelayState
OBJECT-TYPE
This object indicates DHCPv6 relay function is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.86.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
dhcpv6RelayHopCount
OBJECT-TYPE
This object indicates the maximum number of router hops that the DHCPv6 packets can cross.
1.3.6.1.4.1.171.10.75.16.1.86.1.2INTEGER (1..16)read-writecurrent
dhcpv6RelayManagement
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.86.2
dhcpv6RelayInterfaceSettingsTable
OBJECT-TYPE
This table indicates the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.86.2.1not-accessiblecurrent
dhcpv6RelayInterfaceSettingsEntry
OBJECT-TYPE
A list of information indicates the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.86.2.1.1not-accessiblecurrent
dhcpv6RelayInterface
OBJECT-TYPE
This object indicates the maximum number of router hops that the DHCPv6 packets can cross.
1.3.6.1.4.1.171.10.75.16.1.86.2.1.1.1DisplayString (SIZE(0..12))read-onlycurrent
dhcpv6RelayServerIP
OBJECT-TYPE
This object indicates the DHCP server IP address.
1.3.6.1.4.1.171.10.75.16.1.86.2.1.1.2Ipv6Addressread-onlycurrent
dhcpv6RelayInterfaceSettingsRowStatus
OBJECT-TYPE
This object indicates the status of this entry.
1.3.6.1.4.1.171.10.75.16.1.86.2.1.1.99RowStatusread-createcurrent
dhcpv6RelayOption37
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.86.3
dhcpv6RelayOption37State
OBJECT-TYPE
This object indicates DHCPv6 relay option 37 function is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.86.3.1INTEGER {disabled(0), enabled(1)}read-writecurrent
dhcpv6RelayOption37CheckState
OBJECT-TYPE
This object indicates DHCPv6 relay option 37 Check function is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.86.3.2INTEGER {disabled(0), enabled(1)}read-writecurrent
dhcpv6RelayOption37RemoteIDType
OBJECT-TYPE
This object indicates the type of remote ID.
1.3.6.1.4.1.171.10.75.16.1.86.3.3INTEGER {default(0), cid-with-user-define(1), user-define(2)}read-writecurrent
dhcpv6RelayOption37RemoteID
OBJECT-TYPE
This object displays the current remote ID of the device. If RemoteIDType is set to default, the value will be the MAC address of the device, and this object cannot be modified. If RemoteIDType is set to user-defined, a new value can be written to this object.
1.3.6.1.4.1.171.10.75.16.1.86.3.4DisplayStringread-writecurrent
dhcpv6RelayOption38
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.86.4
dhcpv6RelayOpt38Table
OBJECT-TYPE
A table to control port security features of the device.
1.3.6.1.4.1.171.10.75.16.1.86.4.1not-accessiblecurrent
dhcpv6RelayOpt38Entry
OBJECT-TYPE
An entry appears in port security table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.86.4.1.1not-accessiblecurrent
dhcpv6RelayOpt38PortIndex
OBJECT-TYPE
The interface index for which the configuration in this entry applies. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.86.4.1.1.1Integer32 (1..26)read-onlycurrent
dhcpv6RelayOpt38PortState
OBJECT-TYPE
Enable / disable option 38 port state.
1.3.6.1.4.1.171.10.75.16.1.86.4.1.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
dhcpv6RelayOpt38PortType
OBJECT-TYPE
Configure option 38 port Type.
1.3.6.1.4.1.171.10.75.16.1.86.4.1.1.3INTEGER {default(0), user-defined(1)}read-writecurrent
dhcpv6RelayOpt38PortID
OBJECT-TYPE
Configure option 38 port ID. Only works when type is user-defined
1.3.6.1.4.1.171.10.75.16.1.86.4.1.1.4DisplayStringread-writecurrent
dhcpv6RelayOption18
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.86.5
dhcpv6RelayOption18State
OBJECT-TYPE
This object indicates DHCPv6 relay option 18 function is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.86.5.1INTEGER {disabled(0), enabled(1)}read-writecurrent
dhcpv6RelayOption18CheckState
OBJECT-TYPE
This object indicates DHCPv6 relay option 18 Check function is enabled or disabled.
1.3.6.1.4.1.171.10.75.16.1.86.5.2INTEGER {disabled(0), enabled(1)}read-writecurrent
dhcpv6RelayOption18InterfaceIDType
OBJECT-TYPE
This object indicates the type of Interface ID.
1.3.6.1.4.1.171.10.75.16.1.86.5.3INTEGER {default(0), cid(1), vendor1(2)}read-writecurrent
companyMldsGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.88
mldsSystem
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.88.1
mldsStatus
OBJECT-TYPE
Enables or disables MLD snooping in the system. When set to 'enabled', the MLDS module starts protocol operations. When set to 'disabled', the MLDS module stops performing protocol operations.
1.3.6.1.4.1.171.10.75.16.1.88.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
mldsRouterPortPurgeInterval
OBJECT-TYPE
This is the interval (in seconds) after which a learnt router port entry will be purged. For each router port learnt, this timer runs for 'RouterPortPurgeInterval' seconds.When the timer expires, the learnt router port entry is purged. However if control messages are received from the router before the timer expiry, then the timer is restarted.
1.3.6.1.4.1.171.10.75.16.1.88.1.2Integer32 (60..600)read-writecurrent
mldsHostPortPurgeInterval
OBJECT-TYPE
This is the interval (in seconds) after which a learnt port entry will be purged. For each port on which report has been received this timer runs for 'PortPurgeInterval' seconds. This timer will be restarted whenever a report message is received from a host on the specific port. If the timer expires, then , the learnt port entry will be purged from the multicast group.
1.3.6.1.4.1.171.10.75.16.1.88.1.3Integer32 (130..153025)read-writecurrent
mldsDataDrivenLearningMaxLearnedEntryVlaue
OBJECT-TYPE
The maximum data driven learning entry value.
1.3.6.1.4.1.171.10.75.16.1.88.1.8INTEGER (1..1024)read-writecurrent
mldsVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.88.3
mldsVlanRouterTable
OBJECT-TYPE
This table contains the list of ports through which a router, in a particular VLAN is reachable.
1.3.6.1.4.1.171.10.75.16.1.88.3.3not-accessiblecurrent
mldsVlanRouterEntry
OBJECT-TYPE
Contains the VLAN ID and list of ports on which routers are present in the VLAN.
1.3.6.1.4.1.171.10.75.16.1.88.3.3.1not-accessiblecurrent
mldsVlanRouterVlanId
OBJECT-TYPE
VLAN ID of the ports through which router is reachable.
1.3.6.1.4.1.171.10.75.16.1.88.3.3.1.1Integer32 (1..4094)read-onlycurrent
mldsVlanRouterPortList
OBJECT-TYPE
List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.
1.3.6.1.4.1.171.10.75.16.1.88.3.3.1.2PortListread-onlycurrent
mldsVlanFilterTable
OBJECT-TYPE
This table contains configuration of snooping on specific Vlans. This Table is valid only when VLAN is enabled in the system.
1.3.6.1.4.1.171.10.75.16.1.88.3.4not-accessiblecurrent
mldsVlanFilterEntry
OBJECT-TYPE
Contains snooping status , version and fast leave configuration for a specific VLAN.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1not-accessiblecurrent
mldsVlanFilterVlanId
OBJECT-TYPE
Index of MldsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in MldsVlanFilterEntry is to be done.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.1Integer32 (1..4094)read-onlycurrent
mldsVlanSnoopStatus
OBJECT-TYPE
This object allows you to enable/disable MLDS function on a specific VLAN.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
mldsVlanQuerier
OBJECT-TYPE
Indicates whether the switch is configured as a querier in the VLAN
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.3INTEGER {enabled(1), disabled(2)}read-onlycurrent
mldsVlanCfgQuerier
OBJECT-TYPE
The snooping switch can be configured as a querier via this object to send out MLD general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
mldsVlanQueryInterval
OBJECT-TYPE
This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in the network.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.5Integer32 (60..600)read-writecurrent
mldsVlanRtrPortList
OBJECT-TYPE
List of ports which are configured statically as router ports
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.6PortListread-writecurrent
mldsVlanFbdRtrPortList
OBJECT-TYPE
List of ports which can be configured statically as forbidden router ports.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.7PortListread-writecurrent
mldsVlanFastLeave
OBJECT-TYPE
Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removing the port from the forwarding table. If set to 'enabled', the switch does not send a group specific query and immediately removes the port from the forwarding table.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
mldsVlanDataDrivenLearningStatus
OBJECT-TYPE
This object allows you to enable/disable Data Driven Learning function on a specific VLAN.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.9INTEGER {enabled(1), disabled(2)}read-writecurrent
mldsVlanReportSuppression
OBJECT-TYPE
Enables or disables Report suppression in the system.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.10INTEGER {enabled(1), disabled(2)}read-writecurrent
mldsVlanRobustnessValue
OBJECT-TYPE
When the switch receives leave message on a port, it sends group specific query to check if there are any other interested receivers for the group. This attribute defines the maximum number of queries sent by the switch before deleting the port from the group membership information in the forwarding database. If the maximum retry count exceeds 'mldsRobustnessValue', then the port will be deleted from the multicast group membership information in the forwarding database and received leave message will be forwarded onto the router ports if there are no interested receivers for the group.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.11Integer32 (2..255)read-writecurrent
mldsVlanGrpQueryInterval
OBJECT-TYPE
The value of this attribute defines the time period with which the switch will send group specific queries on a port to check if there is any intersted receivers. The switch will send 'mldsRobustnessValue' queries before removing the port from the group membership information in the forwarding database.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.12Integer32 (1..25)read-writecurrent
mldsVlanQueryMaxResponseTime
OBJECT-TYPE
The maximum query response time advertised in MLDv1 general queries on this interface.
1.3.6.1.4.1.171.10.75.16.1.88.3.4.1.13INTEGER (10..25)read-writecurrent
mldsVlanMulticastGroupTable
OBJECT-TYPE
This table contains MAC based multicast forwarding information.
1.3.6.1.4.1.171.10.75.16.1.88.3.5not-accessiblecurrent
mldsVlanMulticastGroupEntry
OBJECT-TYPE
This table contains VLAN ID, multicast group MAC address and the list of ports onto which the multicast data packets for group should be forwarded.
1.3.6.1.4.1.171.10.75.16.1.88.3.5.1not-accessiblecurrent
mldsVlanMulticastGroupVlanId
OBJECT-TYPE
VLAN ID pertaining to the Multicast forwarding entry
1.3.6.1.4.1.171.10.75.16.1.88.3.5.1.1Integer32 (1..4094)read-onlycurrent
mldsVlanMulticastGroupIpAddress
OBJECT-TYPE
Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.
1.3.6.1.4.1.171.10.75.16.1.88.3.5.1.2InetAddressread-onlycurrent
mldsVlanMulticastGroupMacAddress
OBJECT-TYPE
Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.
1.3.6.1.4.1.171.10.75.16.1.88.3.5.1.3MacAddressread-onlycurrent
mldsVlanMulticastGroupPortList
OBJECT-TYPE
List of ports onto which the multicast data packets destined for this group will be forwarded.
1.3.6.1.4.1.171.10.75.16.1.88.3.5.1.4PortListread-onlycurrent
mldsHost
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.88.4
mldsHostTable
OBJECT-TYPE
This table is used to manage the IGMP Host based Fast Leave function of the switch.
1.3.6.1.4.1.171.10.75.16.1.88.4.1not-accessiblecurrent
mldsHostEntry
OBJECT-TYPE
Contains management entities for IGMP Host based fast leave function.
1.3.6.1.4.1.171.10.75.16.1.88.4.1.1not-accessiblecurrent
mldsHostTableVLANID
OBJECT-TYPE
VLAN ID of IPv6 Host table entry.
1.3.6.1.4.1.171.10.75.16.1.88.4.1.1.1Integer32 (1..4094)read-onlycurrent
mldsHostTableGroupAddress
OBJECT-TYPE
Group address of IPv6 Host table entry.
1.3.6.1.4.1.171.10.75.16.1.88.4.1.1.2Ipv6Addressread-onlycurrent
mldsHostTablePort
OBJECT-TYPE
Port number of IPv6 Host table entry. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.88.4.1.1.3Integer32 (1..26)read-onlycurrent
mldsHostTableHostIPAddress
OBJECT-TYPE
Host IP address of Group in IPv6 Host table entry.
1.3.6.1.4.1.171.10.75.16.1.88.4.1.1.4Ipv6Addressread-onlycurrent
companyPPPoE
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.98
pppoeGlobalState
OBJECT-TYPE
PPPoE global state
1.3.6.1.4.1.171.10.75.16.1.98.1INTEGER {disabled(0), enabled(1)}read-writecurrent
pppoePortTable
OBJECT-TYPE
A table to control PPPoE features of the device.
1.3.6.1.4.1.171.10.75.16.1.98.2not-accessiblecurrent
pppoePortEntry
OBJECT-TYPE
An entry appears in PPPoE table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.98.2.1not-accessiblecurrent
pppoePortIndex
OBJECT-TYPE
Interface index of the port for the configuration in this entry applies.
1.3.6.1.4.1.171.10.75.16.1.98.2.1.1Integer32 (1..6)read-onlycurrent
pppoePortState
OBJECT-TYPE
PPPoE per port state
1.3.6.1.4.1.171.10.75.16.1.98.2.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
pppoePortCircuitIDType
OBJECT-TYPE
PPPoE per port circuit ID type
1.3.6.1.4.1.171.10.75.16.1.98.2.1.3INTEGER {ip(0), mac(1), udf(2), vendor2(3), vendor3(4)}read-writecurrent
pppoePortUDFString
OBJECT-TYPE
PPPoE per port UDF string
1.3.6.1.4.1.171.10.75.16.1.98.2.1.4DisplayString (SIZE(1..32))read-writecurrent
pppoePortCircuitIDVendor3String
OBJECT-TYPE
PPPoE per port circuit ID vendor3 string
1.3.6.1.4.1.171.10.75.16.1.98.2.1.5DisplayString (SIZE(1..32))read-writecurrent
pppoePortRemoteIDType
OBJECT-TYPE
PPPoE per port remote ID type
1.3.6.1.4.1.171.10.75.16.1.98.2.1.6INTEGER {default(0), vendor2(1), vendor3(2)}read-writecurrent
pppoePortRemoteIDVendor3String
OBJECT-TYPE
PPPoE per port remote ID vendor3 string
1.3.6.1.4.1.171.10.75.16.1.98.2.1.7DisplayString (SIZE(1..32))read-writecurrent
companyDoSCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.99
doSCtrlTable
OBJECT-TYPE
A table that holds the DoS prevention settings of the device.
1.3.6.1.4.1.171.10.75.16.1.99.1not-accessiblecurrent
doSCtrlEntry
OBJECT-TYPE
A list of DoS prevention settings of the device.
1.3.6.1.4.1.171.10.75.16.1.99.1.1not-accessiblecurrent
doSCtrlType
OBJECT-TYPE
This object indicates the DoS prevention type.
1.3.6.1.4.1.171.10.75.16.1.99.1.1.1INTEGER {land-attack(1), blat-attack(2), smurf-attack(3), tcp-null-scan(4), tcp-xmascan(5), tcp-synfin(6), tcp-syn-srcport-less-1024(7)}read-onlycurrent
doSCtrlState
OBJECT-TYPE
This object indicates the status of the DoS prevention type.
1.3.6.1.4.1.171.10.75.16.1.99.1.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
doSCtrlActionType
OBJECT-TYPE
This object indicates the action for the DoS prevention type. If this object is set to 'mirror' and DoSCtrlState is set to 'enable', the configuration will not take effect until a valid mirror port is specified. If mirror port is not valid the behavior will be the same as 'drop'
1.3.6.1.4.1.171.10.75.16.1.99.1.1.3INTEGER {drop(0), mirror(1)}read-writecurrent
doSCtrlMirrorPort
OBJECT-TYPE
This object indicates the port to which the attack packet will be forwarded. A value of 0 means that the DoS prevention action type is either not set to 'mirror'. or the 'mirror' DoS action is not active. When DoSCtrlActionType is set to 'mirror' with DoSCtrlState set to 'enable', setting this value to a valid port number will activate the 'mirror' DoS action.
1.3.6.1.4.1.171.10.75.16.1.99.1.1.4INTEGER (0..65535)read-writecurrent
doSCtrlMirrorReplace1P
OBJECT-TYPE
This object indicates the packet to which the attack packet will be replaced 1p to mirror port. The Range of 1p is 0 ~ 7. If value set to -1, it means no chenged.
1.3.6.1.4.1.171.10.75.16.1.99.1.1.5INTEGER (-1..7)read-writecurrent
doSCtrlMirrorRxRate
OBJECT-TYPE
This object indicates the packet to which the attack packet will be rate limited to mirror port. The Range of rx limit is 0 or 64~1024000. If rate set to 0, it means no limit.
1.3.6.1.4.1.171.10.75.16.1.99.1.1.6INTEGER (0..1024000)read-writecurrent
doSCtrlFrameCount
OBJECT-TYPE
This object indicates the frame counts of the DoS prevention type.
1.3.6.1.4.1.171.10.75.16.1.99.1.1.7INTEGERread-onlycurrent
doSCtrlClearFrameCount
OBJECT-TYPE
This object will clear frame count when set to clear.
1.3.6.1.4.1.171.10.75.16.1.99.1.1.8INTEGER {normal(0), clear(1)}read-writecurrent
dosCtrlTrapLogState
OBJECT-TYPE
Enable/Disable Dos Trap Log function. Default is disabled.
1.3.6.1.4.1.171.10.75.16.1.99.2INTEGER {disabled(0), enabled(1)}read-writecurrent
companyAgentBasicInfo
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.100
agentCPUutilization
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.100.1
agentCPUutilizationIn5sec
OBJECT-TYPE
The time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.10.75.16.1.100.1.1Integer32read-onlycurrent
agentCPUutilizationIn1min
OBJECT-TYPE
The time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.10.75.16.1.100.1.2Integer32read-onlycurrent
agentCPUutilizationIn5min
OBJECT-TYPE
The time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.10.75.16.1.100.1.3Integer32read-onlycurrent
agentMEMutilization
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.100.2
agentMEMutilizationIn5sec
OBJECT-TYPE
The time scale is set at 5 second intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.10.75.16.1.100.2.1Integer32read-onlycurrent
agentMEMutilizationIn1min
OBJECT-TYPE
The time scale is set at 1 minute intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.10.75.16.1.100.2.2Integer32read-onlycurrent
agentMEMutilizationIn5min
OBJECT-TYPE
The time scale is set at 5 minute intervals. The value will be between 0% (idle) and 100% (very busy).
1.3.6.1.4.1.171.10.75.16.1.100.2.3Integer32read-onlycurrent
companyProtocolVlan
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.101
protocolGroupNameTable
OBJECT-TYPE
A table to control protocol group name features of the device.
1.3.6.1.4.1.171.10.75.16.1.101.1not-accessiblecurrent
protocolGroupNameEntry
OBJECT-TYPE
An entry appears in protocol group name table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.101.1.1not-accessiblecurrent
protocolGroupGID
OBJECT-TYPE
The group ID of protocol group name table.
1.3.6.1.4.1.171.10.75.16.1.101.1.1.1Integer32 (1..16)read-onlycurrent
protocolGroupName
OBJECT-TYPE
The group name of protocol group name table.
1.3.6.1.4.1.171.10.75.16.1.101.1.1.2DisplayString (SIZE(1..32))read-writecurrent
protocolGroupTable
OBJECT-TYPE
A table to control protocol group features of the device.
1.3.6.1.4.1.171.10.75.16.1.101.2not-accessiblecurrent
protocolGroupEntry
OBJECT-TYPE
An entry appears in protocol group table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.101.2.1not-accessiblecurrent
protocolGroupId
OBJECT-TYPE
The group ID of protocol group table.
1.3.6.1.4.1.171.10.75.16.1.101.2.1.1Integer32 (1..16)read-onlycurrent
protocolGroupFrameType
OBJECT-TYPE
The frame type of protocol group table.
1.3.6.1.4.1.171.10.75.16.1.101.2.1.2INTEGER {ethernet(1), ieee8023-snap(2)}read-onlycurrent
protocolGroupProtocolValue
OBJECT-TYPE
The protocol value of protocol group table.
1.3.6.1.4.1.171.10.75.16.1.101.2.1.3Integer32 (0..65535)read-onlycurrent
protocolGroupRowStatus
OBJECT-TYPE
The row status of protocol group table.
1.3.6.1.4.1.171.10.75.16.1.101.2.1.99RowStatusread-createcurrent
protocolVlanTable
OBJECT-TYPE
A table to control protocol vlan features of the device.
1.3.6.1.4.1.171.10.75.16.1.101.3not-accessiblecurrent
protocolVlanEntry
OBJECT-TYPE
An entry appears in protocol vlan table for each interface in the system.
1.3.6.1.4.1.171.10.75.16.1.101.3.1not-accessiblecurrent
protocolVlanPort
OBJECT-TYPE
The interface number of protocol vlan table.
1.3.6.1.4.1.171.10.75.16.1.101.3.1.1Integer32 (1..28)read-onlycurrent
protocolVlanVID
OBJECT-TYPE
The vlan ID of protocol vlan table.
1.3.6.1.4.1.171.10.75.16.1.101.3.1.2Integer32 (1..4094)read-onlycurrent
protocolVlanGroupID
OBJECT-TYPE
The group ID of protocol vlan table.
1.3.6.1.4.1.171.10.75.16.1.101.3.1.3Integer32 (1..16)read-onlycurrent
protocolVlanRowStatus
OBJECT-TYPE
The row status of protocol vlan table.
1.3.6.1.4.1.171.10.75.16.1.101.3.1.99RowStatusread-createcurrent
companyL2PT
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.102
l2PTState
OBJECT-TYPE
This object indicates the global state of Layer 2 protocol tunneling.
1.3.6.1.4.1.171.10.75.16.1.102.1INTEGER {enabled(1), disabled(2)}read-writecurrent
l2PTPortTable
OBJECT-TYPE
A table that cont ains the cable situation for each port.
1.3.6.1.4.1.171.10.75.16.1.102.2not-accessiblecurrent
l2PTEntry
OBJECT-TYPE
A list of cable situations for each port on the device.
1.3.6.1.4.1.171.10.75.16.1.102.2.1not-accessiblecurrent
l2PTPortIndex
OBJECT-TYPE
This object indicates the port number. For all machines give maximum port number.
1.3.6.1.4.1.171.10.75.16.1.102.2.1.1INTEGER (1..26)not-accessiblecurrent
l2PTPortType
OBJECT-TYPE
This object indicates the Layer 2 protocol tunneling port type. The 'none' value indicates that the port is normal. Layer 2 protocol tunneling is disabled on this port. The 'uni' value indicates that the port is connected to the customer site. A Layer 2 PDU received on a UNI port can be tunneled to a remote customer site across the provider network. The 'nni' value indicates that the port is connected to the provider network. A Tunneled Layer 2 PDU received on an NNI port will be restored to its original format.
1.3.6.1.4.1.171.10.75.16.1.102.2.1.2INTEGER {none(1), uni(2), nni(3)}read-writecurrent
l2PTProtocol
OBJECT-TYPE
This object indicates the tunneled protocols on this port. This object can only be applied on a UNI port. If the 'stp' BIT is set, the STP BPDU will be tunneled. If the 'gvrp' BIT is set, the GVRP PDU will be tunneled. If the 'mac-01-00-0C-CC-CC-CC' BIT is set, the PDU with the destination MAC address 01-00-0C-CC-CC-CC will be tunneled . If the 'mac-01-00-0C-CC-CC-CD' BIT is set, then the PDU with the destination MAC address 01-00-0C-CC-CC-CD will be tunneled.
1.3.6.1.4.1.171.10.75.16.1.102.2.1.3Bits {stp(0), gvrp(1), macCC(2), macCD(3)}read-writecurrent
l2PTThresholdTable
OBJECT-TYPE
This table contains the protocol tunneling threshold of a UNI port.
1.3.6.1.4.1.171.10.75.16.1.102.3not-accessiblecurrent
l2PTThresholdEntry
OBJECT-TYPE
A list with the Layer2 Protocol tunneling threshold.
1.3.6.1.4.1.171.10.75.16.1.102.3.1not-accessiblecurrent
l2PTProtocolIndex
OBJECT-TYPE
This object indicates the tunneled protocol of the port.
1.3.6.1.4.1.171.10.75.16.1.102.3.1.1INTEGER {stp(1), gvrp(2), macCC(3), macCD(4)}not-accessiblecurrent
l2PTDropThreshold
OBJECT-TYPE
This object indicates the drop threshold for a given protocol on a UNI port. If the arrival rate of a tunneled protocol has reached its threshold, the received PDUs of this protocol will be dropped. The value 0 indicates there is no threshold for the protocol.
1.3.6.1.4.1.171.10.75.16.1.102.3.1.2INTEGER (0..65535)read-writecurrent
companySfpVendorInfo
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.104
sfpVendorInfoTable
OBJECT-TYPE
This table indicates the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.104.1not-accessiblecurrent
sfpVendorInfoEntry
OBJECT-TYPE
A list of information indicates the IP address as a destination to forward (relay) DHCP packets to.
1.3.6.1.4.1.171.10.75.16.1.104.1.1not-accessiblecurrent
sfpPortIndex
OBJECT-TYPE
The available of index for fiber ports.
1.3.6.1.4.1.171.10.75.16.1.104.1.1.1Integer32 (1..26)read-onlycurrent
sfpConnectorType
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.2DisplayStringread-onlycurrent
sfpTranceiverCode
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.3DisplayStringread-onlycurrent
sfpBaudRate
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.4DisplayStringread-onlycurrent
sfpVendorName
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.5DisplayStringread-onlycurrent
sfpVendorOui
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.6DisplayStringread-onlycurrent
sfpVendorPn
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.7DisplayStringread-onlycurrent
sfpVendorRev
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.8DisplayStringread-onlycurrent
sfpWavelength
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.9DisplayStringread-onlycurrent
sfpVendorSn
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.10DisplayStringread-onlycurrent
sfpDateCode
OBJECT-TYPE
1.3.6.1.4.1.171.10.75.16.1.104.1.1.11DisplayStringread-onlycurrent
companyDDM
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.105
ddmCtrl
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.105.1
ddmPowerUnit
OBJECT-TYPE
This object indicates the TX/RX power global unit.
1.3.6.1.4.1.171.10.75.16.1.105.1.1INTEGER {mw(0), dbm(1)}read-writecurrent
ddmActionMgmtTable
OBJECT-TYPE
This table contains the configuration of the action taken when any parameter exceeds its threshold.
1.3.6.1.4.1.171.10.75.16.1.105.1.2not-accessibleobsolete
ddmActionMgmtEntry
OBJECT-TYPE
This is an entry of the swDdmConfigActionTable.
1.3.6.1.4.1.171.10.75.16.1.105.1.2.1not-accessibleobsolete
ddmActionPort
OBJECT-TYPE
This object indicates the port. The available of index for fiber ports.
1.3.6.1.4.1.171.10.75.16.1.105.1.2.1.1INTEGER (1..26)read-onlycurrent
ddmActionState
OBJECT-TYPE
This object indicates the action type.
1.3.6.1.4.1.171.10.75.16.1.105.1.2.1.2INTEGER {disable(0), enable(1)}read-writeobsolete
ddmActionShutdown
OBJECT-TYPE
This object indicates the action type.
1.3.6.1.4.1.171.10.75.16.1.105.1.2.1.3INTEGER {none(0), alarm(1), warning(2)}read-writeobsolete
ddmThresholdMgmtTable
OBJECT-TYPE
This table contains DDM temperature configuration information.
1.3.6.1.4.1.171.10.75.16.1.105.1.3not-accessiblecurrent
ddmThresholdMgmtEntry
OBJECT-TYPE
This is an entry of the swDdmConfigThresholdTable.
1.3.6.1.4.1.171.10.75.16.1.105.1.3.1not-accessiblecurrent
ddmThresholdPort
OBJECT-TYPE
This object indicates the port. The available of index for fiber ports.
1.3.6.1.4.1.171.10.75.16.1.105.1.3.1.1INTEGER (1..26)read-onlycurrent
ddmThresholdType
OBJECT-TYPE
This object indicates the threshold type.
1.3.6.1.4.1.171.10.75.16.1.105.1.3.1.2INTEGER {temperature(0), voltage(1), bias(2), txPower(3), rxPower(4)}read-onlycurrent
ddmHighAlarm
OBJECT-TYPE
This object indicates the high alarm threshold value to be configured. As the value is a floating point data type, the DisplayString type is used to define this parameter.
1.3.6.1.4.1.171.10.75.16.1.105.1.3.1.3DisplayStringread-writecurrent
ddmLowAlarm
OBJECT-TYPE
This object indicates the low alarm threshold value to be configured. As the value is a floating data type, the DisplayString type is used to define this parameter.
1.3.6.1.4.1.171.10.75.16.1.105.1.3.1.4DisplayStringread-writecurrent
ddmHighWarning
OBJECT-TYPE
This object indicates the high warning threshold value to be configured. As the value is a floating data type, the DisplayString type is used to define this parameter.
1.3.6.1.4.1.171.10.75.16.1.105.1.3.1.5DisplayStringread-writecurrent
ddmLowWarning
OBJECT-TYPE
This object indicates the low warning threshold value to be configured. As the value is a floating data type, the DisplayString type is used to define this parameter.
1.3.6.1.4.1.171.10.75.16.1.105.1.3.1.6DisplayStringread-writecurrent
ddmInfo
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.105.2
ddmStatus
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.105.2.1
ddmStatusTable
OBJECT-TYPE
This table contains the DDM status information.
1.3.6.1.4.1.171.10.75.16.1.105.2.1.1not-accessiblecurrent
ddmStatusEntry
OBJECT-TYPE
This is an entry of the ddmStatusTable.
1.3.6.1.4.1.171.10.75.16.1.105.2.1.1.1not-accessiblecurrent
ddmStatusPort
OBJECT-TYPE
This object indicates the port. The available of index for fiber ports.
1.3.6.1.4.1.171.10.75.16.1.105.2.1.1.1.1INTEGER (1..26)read-onlycurrent
ddmTemperature
OBJECT-TYPE
This object indicates the real time value of the temperature. As the value is a floating point data type, the DisplayString type is used to define this parameter.
1.3.6.1.4.1.171.10.75.16.1.105.2.1.1.1.2DisplayStringread-onlycurrent
ddmVoltage
OBJECT-TYPE
This object indicates the real time value of the supply voltage. As the value value is a floating point data type, the DisplayString type is used to define this parameter.
1.3.6.1.4.1.171.10.75.16.1.105.2.1.1.1.3DisplayStringread-onlycurrent
ddmBiasCurrent
OBJECT-TYPE
This object indicates the real time value of the tx bias.
1.3.6.1.4.1.171.10.75.16.1.105.2.1.1.1.4DisplayStringread-onlycurrent
ddmTxPower
OBJECT-TYPE
This object indicates the real time value of the tx power. As the value is a floating point data type, the DisplayString type is used to define this parameter.
1.3.6.1.4.1.171.10.75.16.1.105.2.1.1.1.5DisplayStringread-onlycurrent
ddmRxPower
OBJECT-TYPE
This object indicates the real time value of the rx power. As the value is a floating data type, the DisplayString type is used to define this parameter.
1.3.6.1.4.1.171.10.75.16.1.105.2.1.1.1.6DisplayStringread-onlycurrent
companyFTPGroup
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.107
ftpFwTable
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.107.1
ftpFwServerIpAddress
OBJECT-TYPE
The FTP server's IPv4 address or IPv6 address is used to upload or download firmware.
1.3.6.1.4.1.171.10.75.16.1.107.1.1DisplayString (SIZE(1..64))read-writeobsolete
ftpFwImageFileName
OBJECT-TYPE
Firmware file name used to upload or download firmware.
1.3.6.1.4.1.171.10.75.16.1.107.1.2DisplayString (SIZE(1..64))read-writeobsolete
ftpFwUsername
OBJECT-TYPE
FTP username to login FTP.
1.3.6.1.4.1.171.10.75.16.1.107.1.3DisplayString (SIZE(1..20))read-writeobsolete
ftpFwPassword
OBJECT-TYPE
FTP password to login FTP.
1.3.6.1.4.1.171.10.75.16.1.107.1.4DisplayString (SIZE(1..20))read-writeobsolete
ftpFwPath
OBJECT-TYPE
FTP path can find file folder.
1.3.6.1.4.1.171.10.75.16.1.107.1.5DisplayString (SIZE(1..64))read-writeobsolete
ftpFwPort
OBJECT-TYPE
FTP port to login FTP.
1.3.6.1.4.1.171.10.75.16.1.107.1.6Integer32 (1..65535)read-writeobsolete
ftpFwFTPOperation
OBJECT-TYPE
The FTP operates to perform downloading the firmware image to the unit. This object is used in conjunction with FTP settings
1.3.6.1.4.1.171.10.75.16.1.107.1.8INTEGER {none(0), download(1), upload(2)}read-writeobsolete
ftpFwFTPOperationStatus
OBJECT-TYPE
The FTP operation status represent firmware backup or upgrade status.
1.3.6.1.4.1.171.10.75.16.1.107.1.9INTEGER {none(0), success(1), fail(2), progressing(3), transmit(4)}read-onlyobsolete
ftpConfigTable
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.107.2
ftpConfigServerIpAddress
OBJECT-TYPE
The FTP server's IPv4 address or IPv6 address is used to upload or download firmware.
1.3.6.1.4.1.171.10.75.16.1.107.2.1DisplayString (SIZE(1..64))read-writeobsolete
ftpConfigFileName
OBJECT-TYPE
Config file name used to upload or download Config.
1.3.6.1.4.1.171.10.75.16.1.107.2.2DisplayString (SIZE(1..64))read-writeobsolete
ftpConfigUsername
OBJECT-TYPE
FTP username to login FTP.
1.3.6.1.4.1.171.10.75.16.1.107.2.3DisplayString (SIZE(1..20))read-writeobsolete
ftpConfigPassword
OBJECT-TYPE
FTP password to login FTP.
1.3.6.1.4.1.171.10.75.16.1.107.2.4DisplayString (SIZE(1..20))read-writeobsolete
ftpConfigPath
OBJECT-TYPE
FTP path can find file folder.
1.3.6.1.4.1.171.10.75.16.1.107.2.5DisplayString (SIZE(1..64))read-writeobsolete
ftpConfigPort
OBJECT-TYPE
FTP port to login FTP.
1.3.6.1.4.1.171.10.75.16.1.107.2.6Integer32 (1..65535)read-writeobsolete
ftpConfigConfigID
OBJECT-TYPE
Config image id can select imageid1 or imageid2 to flash
1.3.6.1.4.1.171.10.75.16.1.107.2.7INTEGER {configID1(1), configID2(2)}read-writecurrent
ftpConfigFTPOperation
OBJECT-TYPE
The FTP operates to perform downloading the config image to the unit. This object is used in conjunction with FTP settings
1.3.6.1.4.1.171.10.75.16.1.107.2.8INTEGER {none(0), download(1), upload(2)}read-writeobsolete
ftpConfigFTPOperationStatus
OBJECT-TYPE
The FTP operation status represent config backup or upgrade status.
1.3.6.1.4.1.171.10.75.16.1.107.2.9INTEGER {none(0), success(1), fail(2), progressing(3), transmit(4)}read-onlyobsolete
companyTraps
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.120
traps
OBJECT-IDENTITY
1.3.6.1.4.1.171.10.75.16.1.120.0

Notifications

NameOIDStatus
brgAddress
NOTIFICATION-TYPE
The MAC address used by this bridge when it must be referred to in a unique fashion.
1.3.6.1.4.1.171.10.75.16.1.6.1.16.1current
oldDesignatedRoot
NOTIFICATION-TYPE
The bridge identifier of the old root of the spanning tree instance as determined by the Spanning Tree Protocol as executed by this node.
1.3.6.1.4.1.171.10.75.16.1.6.1.16.2current
mstiBridgeRegionalRoot
NOTIFICATION-TYPE
MSTI Regional Root Identifier value for the Instance.
1.3.6.1.4.1.171.10.75.16.1.6.1.16.3current
impbBindingtrapsign
NOTIFICATION-TYPE
The object is for IMPB trap sign in the system.
1.3.6.1.4.1.171.10.75.16.1.14.10.15.1current
snmpTrapSNMPAuthentication
NOTIFICATION-TYPE
SnmpV3TrapSNMPAuthentication.
1.3.6.1.4.1.171.10.75.16.1.120.0.1current
snmpTrapColdStart
NOTIFICATION-TYPE
SnmpV3TrapColdStart.
1.3.6.1.4.1.171.10.75.16.1.120.0.2current
snmpTrapWarmStart
NOTIFICATION-TYPE
SnmpV3TrapWarmStart.
1.3.6.1.4.1.171.10.75.16.1.120.0.3current
snmpTrapCopperLinkUpDown
NOTIFICATION-TYPE
SnmpV3TrapCopperLinkUpDown.
1.3.6.1.4.1.171.10.75.16.1.120.0.4current
snmpTrapRSTPStateChange
NOTIFICATION-TYPE
SnmpV3TrapRSTPStateChange.
1.3.6.1.4.1.171.10.75.16.1.120.0.5current
snmpTrapFirmUpgrade
NOTIFICATION-TYPE
SnmpV3TrapFirmUpgrade.
1.3.6.1.4.1.171.10.75.16.1.120.0.6current
snmpTrapBPDUAttack
NOTIFICATION-TYPE
SnmpV3TrapBPDUAttack.
1.3.6.1.4.1.171.10.75.16.1.120.0.11current
snmpTrapPortSecurity
NOTIFICATION-TYPE
SnmpV3TrapPortSecurity.
1.3.6.1.4.1.171.10.75.16.1.120.0.12current
snmpTrapIMPBv2
NOTIFICATION-TYPE
SnmpV3TrapIMPBv2.
1.3.6.1.4.1.171.10.75.16.1.120.0.13current
snmpTrapLBD
NOTIFICATION-TYPE
SnmpV3TrapLBD.
1.3.6.1.4.1.171.10.75.16.1.120.0.14current
snmpTrapDHCPScreen
NOTIFICATION-TYPE
SnmpV3TrapDHCPScreen.
1.3.6.1.4.1.171.10.75.16.1.120.0.15current
snmpTrapGratuitousArp
NOTIFICATION-TYPE
SnmpV3TrapGratuitousArp.
1.3.6.1.4.1.171.10.75.16.1.120.0.16current
macNotificatiotn
NOTIFICATION-TYPE
This trap indicates the MAC address variations in the address table .
1.3.6.1.4.1.171.10.75.16.1.120.0.17current
duplicateIP
NOTIFICATION-TYPE
duplicateIP .
1.3.6.1.4.1.171.10.75.16.1.120.0.21current
trafficControl
NOTIFICATION-TYPE
trafficControl.
1.3.6.1.4.1.171.10.75.16.1.120.0.22current
topologyChange
NOTIFICATION-TYPE
topologyChange.
1.3.6.1.4.1.171.10.75.16.1.120.0.23current
newRootBrgaddress
NOTIFICATION-TYPE
newRootBrgaddress.
1.3.6.1.4.1.171.10.75.16.1.120.0.24current
newRootOlddesignatedroot
NOTIFICATION-TYPE
newRootOlddesignatedroot.
1.3.6.1.4.1.171.10.75.16.1.120.0.25current
newRootMSTibridgeregionalroot
NOTIFICATION-TYPE
topologyChange.
1.3.6.1.4.1.171.10.75.16.1.120.0.26current