MIBs Depot

DASAN-SHDSL-MIB

Registered at
1.3.6.1.4.1.6296.9.6
Last updated
2004-07-15 00:00
Organization
Dasan Co., Ltd.
Namespace
dasan
Source file
DASAN-SHDSL-MIB
Digest
sha256:167a776e0baadcf42375d3795f55ef0d23bed979cf9433dedfeb7beb3848f6e8

Description

The MIB module to describe G.SHDSL product. The MIB module that provides objects that are proprietary and extension to SHDSL- LINE-MIB. The MIB include extension to following Tables. The MIB also include a set of scalar(s) clubbed under the group 'dsShdslCapabilityGroup'.

Contact

Dasan Co., Ltd.

Imports

FromSymbols
DASAN-SMIdasanMgmt
IF-MIBifIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso, mib-2
SNMPv2-TCDisplayString, RowStatus, TEXTUAL-CONVENTION, TimeStamp, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

DASAN-SHDSL-MIB
DASAN-SMI
IANAifType-MIB
IF-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
dasanShdslLineMIB
OBJECT-IDENTITY
1.3.6.1.4.1.6296.9.6.1
dasanShdslMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.6296.9.6.1.1
dsShdslCapabilityGroup
OBJECT-IDENTITY
1.3.6.1.4.1.6296.9.6.1.1.1
dsShdslCapabilityLineTxCap
OBJECT-TYPE
This bitmap specifies the transmission modes that the STU-C is capable of supporting. Right now, support for Annex A (q9921PotsNonOverlapped(2) and q9921PotsOverlapped(3)) is present. This value depends on the DSL PHY firmware present on Columbia MxU.
1.3.6.1.4.1.6296.9.6.1.1.1.1Bits {region1(0), region2(1)}read-onlycurrent
dsShdslLineStatusTable
OBJECT-TYPE
This MO is proprietary extension of RFC 3276 MIB and contains the proprietary line status.
1.3.6.1.4.1.6296.9.6.1.1.2not-accessiblecurrent
dsShdslLineStatusEntry
OBJECT-TYPE
An entry (conceptual row) in the dsShdslLineStatusTable. The Table is indexed by ifIndex.
1.3.6.1.4.1.6296.9.6.1.1.2.1not-accessiblecurrent
dsShdslOpState
OBJECT-TYPE
This object identifies the high level operational state for the STU.
1.3.6.1.4.1.6296.9.6.1.1.2.1.1INTEGER {idle(0), data(1), bootupLoad(8), bootupLoadDone(9), handshake(16), pmms(20), training(24), framerGearShift(26), framerManualReset(27), silence(29), analogLb(128), rmtFramerLb(130), digitalLb(131), spectrumTest(133), selt(138), pSDTest(139), lclFramerLb(142), interfaceLb(143), bertTest(144), analogLbBertTest(145), digLbBertTest(146)}read-onlycurrent
dsShdslStartProgress
OBJECT-TYPE
This object identifies the current detailed operational state of the STU.
1.3.6.1.4.1.6296.9.6.1.1.2.1.2INTEGER {noActivity(0), preActivation(1), activation(4), checkBitrate(7), pmmsChkComnRate(8), transmitCr(55), transmitSc(56), transmitSr(57), coLineAgc(64), cpLineAgc(65), fdEcTrain(66), equalizerTrain(67), tipRingAligned(68), transmitTc(69), receiveTr(70), transmitFc1(71), transmitFc2(72), receiveTc(73), transmitTr(74), receiveFc(75), spectTestOk(113), albTestOk(114), dlbTestOk(115), crcFail(116), framerSyncFail(117), snrMarginFail(118), loadCppa(128), loadCptrain(129), loadCptom(130), loadCpdm(131), loadCopa(144), loadCotrain(145), loadCotom(146), loadCodm(147)}read-onlycurrent
dsShdslFwRelease
OBJECT-TYPE
Transceiver firmware release number.
1.3.6.1.4.1.6296.9.6.1.1.2.1.3OCTET STRING (SIZE(0..255))read-onlycurrent
dsShdslLineSwap
OBJECT-TYPE
This object indicates if the physical lines are swapped, i.e., logical channel A is connected to physical channel B. This applies to 4-wire operation only.
1.3.6.1.4.1.6296.9.6.1.1.2.1.4INTEGER {unswapped(0), swapped(1)}read-onlycurrent
dsShdslRmtCountryCode
OBJECT-TYPE
This object provides the country code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop. GlobespanVirata sets this to USA.
1.3.6.1.4.1.6296.9.6.1.1.2.1.5OCTET STRING (SIZE(0..255))read-onlycurrent
dsShdslRmtEncoderA
OBJECT-TYPE
This object identifies the 21-bit value corresponding to encoder coefficient A, as defined in ITU-T G.991.2, for the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.6INTEGERread-onlycurrent
dsShdslRmtEncoderB
OBJECT-TYPE
This object identifies the 21-bit value corresponding to encoder coefficient B, as defined in ITU-T G.991.2, for the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.7INTEGERread-onlycurrent
dsShdslRmtProviderCode
OBJECT-TYPE
This object identifies the provider code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.8OCTET STRING (SIZE(0..255))read-onlycurrent
dsShdslLocDetect
OBJECT-TYPE
This object is used to determine if carrier has been lost.
1.3.6.1.4.1.6296.9.6.1.1.2.1.9INTEGERread-onlycurrent
dsShdslTxPower
OBJECT-TYPE
This object identifies the local STU transmit power in tenths of a dBm.
1.3.6.1.4.1.6296.9.6.1.1.2.1.10INTEGERread-onlycurrent
dsShdslFramerSync
OBJECT-TYPE
This object returns information regarding the framer synchronization status.
1.3.6.1.4.1.6296.9.6.1.1.2.1.11INTEGER {outOfSync(0), inSync(1)}read-onlycurrent
dsShdslRmtTomData
OBJECT-TYPE
This object provides vendor-provided data, as defined in ITU-T G.991.2, for the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.12INTEGERread-onlycurrent
dsShdslDriftAlarm
OBJECT-TYPE
This object identifies if the receive clock is in or out of range.
1.3.6.1.4.1.6296.9.6.1.1.2.1.13INTEGERread-onlycurrent
dsShdslReceiverGain
OBJECT-TYPE
This object provides the total receiver gain in dB.
1.3.6.1.4.1.6296.9.6.1.1.2.1.14INTEGERread-onlycurrent
dsShdslBertError
OBJECT-TYPE
This object provides the count of bit errors since the last time the object was read, as well as the type of synchronization.
1.3.6.1.4.1.6296.9.6.1.1.2.1.15INTEGER {outOfSync(0), framedSync(64), unframedSync(128)}read-onlycurrent
dsShdslFramerOHAndDefects
OBJECT-TYPE
This object returns overhead data. The four least significant bits contain the overhead data in the following format: bit 0 is losd, bit 1 is sega, bit 2 is ps, and bit 3 is segd.
1.3.6.1.4.1.6296.9.6.1.1.2.1.16OCTET STRING (SIZE(0..10))read-onlycurrent
dsShdslRmtFwVersion
OBJECT-TYPE
This object provides the transceiver firmware release number of the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.17INTEGERread-onlycurrent
dsShdslUtopiaCellDelineation
OBJECT-TYPE
This object indicates whether cell delineation has been found.
1.3.6.1.4.1.6296.9.6.1.1.2.1.18INTEGER {inSync(1), preSync(160), hunt(240)}read-onlycurrent
dsShdslUtopiaRxCellCnt
OBJECT-TYPE
This object indicates the number of UTOPIA cells received since the last time the object has been called. The maximum value is 0xFFFF.
1.3.6.1.4.1.6296.9.6.1.1.2.1.19INTEGERread-onlycurrent
dsShdslUtopiaCellDropCnt
OBJECT-TYPE
This object indicates the number of UTOPIA cells dropped since the last time the object has been called. The maximum value is 0xFF.
1.3.6.1.4.1.6296.9.6.1.1.2.1.20INTEGERread-onlycurrent
dsShdslUtopiaRxHecErrorCnt
OBJECT-TYPE
This object indicates the number of UTOPIA cells with HEC errors since the last time the object has been called. The maximum value is 0xFF.
1.3.6.1.4.1.6296.9.6.1.1.2.1.21INTEGERread-onlycurrent
dsShdslUtopiaTxCellCnt
OBJECT-TYPE
This object indicates the number of UTOPIA cells transmitted since the last time the object has been called. The maximum value is 0xFFFF.
1.3.6.1.4.1.6296.9.6.1.1.2.1.22INTEGERread-onlycurrent
dsShdslRmtNsfCusId
OBJECT-TYPE
This object returns the customer identification that was sent by the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.23INTEGERread-onlycurrent
dsShdslRmtNsfCusData
OBJECT-TYPE
This object returns non-standard format customer data that was sent by the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.24OCTET STRING (SIZE(0..4))read-onlycurrent
dsShdslLocalHandshake
OBJECT-TYPE
This object provides a way to see what capabilities are supported by the local STU. A total of 26 handshake parameters are supported.
1.3.6.1.4.1.6296.9.6.1.1.2.1.25OCTET STRING (SIZE(0..52))read-onlycurrent
dsShdslRemoteHandshake
OBJECT-TYPE
This object provides a way to see what capabilities are supported by the STU at the other end of the loop. A total of 26 handshake parameters are supported.
1.3.6.1.4.1.6296.9.6.1.1.2.1.26OCTET STRING (SIZE(0..52))read-onlycurrent
dsShdslActualHandshake
OBJECT-TYPE
This object provides the results of capabilities exchanged during handshake. A total of 26 handshake parameters are supported.
1.3.6.1.4.1.6296.9.6.1.1.2.1.27OCTET STRING (SIZE(0..52))read-onlycurrent
dsShdslRmtTxPower
OBJECT-TYPE
This object provides the transmit power of the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.28INTEGERread-onlycurrent
dsShdslRmtPowerBackoff
OBJECT-TYPE
This object indicates whether power backoff is enabled or disabled at the STU at the other end of the loop.
1.3.6.1.4.1.6296.9.6.1.1.2.1.29INTEGER {enable(0), disable(32768)}read-onlycurrent
dsShdslAutoRetrainCount
OBJECT-TYPE
This object indicates the number of automatic retrains. This counter is only reset when a startup is initiated.
1.3.6.1.4.1.6296.9.6.1.1.2.1.30INTEGERread-onlycurrent
dsShdslEocState
OBJECT-TYPE
This object provides status information about the eoc stage.
1.3.6.1.4.1.6296.9.6.1.1.2.1.31INTEGER {online(0), discovery(1), inventory(2), configuration(3), cmdInProgress(4)}read-onlycurrent
dsShdslFramerOneSecondCnt
OBJECT-TYPE
This object provides CRC, SEGA, and LOSW defect one second error counts, and should be called every second.
1.3.6.1.4.1.6296.9.6.1.1.2.1.32OCTET STRING (SIZE(0..6))read-onlycurrent
dsShdslNtrFault
OBJECT-TYPE
This object identifies the Network Timing Recovery Fault.
1.3.6.1.4.1.6296.9.6.1.1.2.1.33INTEGER {present(0), absent(1)}read-onlycurrent
dsShdslCpeMasterCore
OBJECT-TYPE
1.3.6.1.4.1.6296.9.6.1.1.2.1.34INTEGER {core0(0), core1(16), core2(32), core3(48), core4(64), core5(80), core6(96), core7(112), noMasterCore(128)}read-onlycurrent
dsShdslParametricTestResult
OBJECT-TYPE
Indicates the Result of the Parametric Test conducted on the Xcvr.
1.3.6.1.4.1.6296.9.6.1.1.2.1.35INTEGER {pass(0), fail(1)}read-onlycurrent
dsShdslParametricTestArray
OBJECT-TYPE
Conexant parameter that indicates the Parametric Test Array.
1.3.6.1.4.1.6296.9.6.1.1.2.1.36OCTET STRING (SIZE(0..1024))read-onlycurrent
dsShdslLineParamsTable
OBJECT-TYPE
This MO is proprietary extension of RFC 3276 MIB and contains the proprietary line parameters.
1.3.6.1.4.1.6296.9.6.1.1.3not-accessiblecurrent
dsShdslLineParamsEntry
OBJECT-TYPE
An entry (conceptual row) in the dsShdslLineParamsTable. The Table is indexed by ifIndex.
1.3.6.1.4.1.6296.9.6.1.1.3.1not-accessiblecurrent
dsShdslAction
OBJECT-TYPE
This object specifies actions that are used to control transceiver operation.
1.3.6.1.4.1.6296.9.6.1.1.3.1.1INTEGER {startUp(0), abortReq(2), gearShiftReq(6), downloadReq(8), bertStartTxReq(17), bertStartRxReq(18), bertStopReq(20), spectrumDownReq(25), spectrumUpReq(26), spectrumTxRxReq(32), hybridLossTestReq(33), residualEchoReq(34), totalEchoReq(35), nextPsdReq(36), autoRetrainOnReq(37), autoRetrainOffReq(38), propEocOnReq(45), propEocOffReq(46), rmtAtmCellStatusReq(47), rmtFullStatusReq(48)}read-writecurrent
dsShdslMode
OBJECT-TYPE
This object specifies the operational mode of the transceiver.
1.3.6.1.4.1.6296.9.6.1.1.3.1.2INTEGER {co(0), cpe(1)}read-writecurrent
dsShdslPowerScale
OBJECT-TYPE
This object is used to compensate for minor differences in transmit power between designs.
1.3.6.1.4.1.6296.9.6.1.1.3.1.3INTEGER {defaultScale(26112)}read-writecurrent
dsShdslFramerType
OBJECT-TYPE
This object defines which type of data interface type is used. Note that the non-default values only apply to Conexant chips that support serial interfaces.
1.3.6.1.4.1.6296.9.6.1.1.3.1.4INTEGER {unframed(0), t1Slotted(1), e1Slotted(2), utopiaL2(3), nx64(6), serialATM(7), vC12(8), iMA(9)}read-onlycurrent
dsShdslAFEType
OBJECT-TYPE
This objects defines which AFE is being used.
1.3.6.1.4.1.6296.9.6.1.1.3.1.5INTEGER {saturn(3), saturnLg(4)}read-onlycurrent
dsShdslEncodeCoeffA
OBJECT-TYPE
This object determines the value of encoder coefficient A, as defined in ITU-T G.991.2.
1.3.6.1.4.1.6296.9.6.1.1.3.1.6INTEGER {default(366)}read-writecurrent
dsShdslEncodeCoeffB
OBJECT-TYPE
This object determines the value of encoder coefficient B, as defined in ITU-T G.991.2
1.3.6.1.4.1.6296.9.6.1.1.3.1.7INTEGER {default(817)}read-writecurrent
dsShdslTxEOCBufferLen
OBJECT-TYPE
This object determines the number of bytes of EOC data that is buffered by the DSP in the transmit direction.
1.3.6.1.4.1.6296.9.6.1.1.3.1.8INTEGER {dsShdslLineParamsTable5(5), dsShdslLineParamsTable10(10), dsShdslLineParamsTable15(15), dsShdslLineParamsTable20(20), dsShdslLineParamsTable25(25), dsShdslLineParamsTable30(30), dsShdslLineParamsTable35(35), dsShdslLineParamsTable40(40), dsShdslLineParamsTable45(45), dsShdslLineParamsTable50(50), dsShdslLineParamsTable55(55), dsShdslLineParamsTable60(60)}read-writecurrent
dsShdslRxEOCBufferLen
OBJECT-TYPE
This object determines the number of bytes of EOC data that is buffered by the DSP in the receive direction.
1.3.6.1.4.1.6296.9.6.1.1.3.1.9INTEGER {dsShdslLineParamsTable5(5), dsShdslLineParamsTable10(10), dsShdslLineParamsTable15(15), dsShdslLineParamsTable20(20), dsShdslLineParamsTable25(25), dsShdslLineParamsTable30(30), dsShdslLineParamsTable35(35), dsShdslLineParamsTable40(40), dsShdslLineParamsTable45(45), dsShdslLineParamsTable50(50), dsShdslLineParamsTable55(55), dsShdslLineParamsTable60(60)}read-writecurrent
dsShdslNTR
OBJECT-TYPE
This object defines how network-timing recovery is performed.
1.3.6.1.4.1.6296.9.6.1.1.3.1.10INTEGER {disable(1), refClkIp8k(2), refClkOp4096k(4)}read-writecurrent
dsShdslRxUpstreamFrameSync
OBJECT-TYPE
Customer-defined value. This object defines the upstream frame sync word.
1.3.6.1.4.1.6296.9.6.1.1.3.1.11INTEGERread-writecurrent
dsShdslRxDownstreamFrameSync
OBJECT-TYPE
This object defines the downstream frame sync word.
1.3.6.1.4.1.6296.9.6.1.1.3.1.12INTEGERread-writecurrent
dsShdslRxUpstreamStuffBits
OBJECT-TYPE
Customer-defined value. This object defines the upstream.
1.3.6.1.4.1.6296.9.6.1.1.3.1.13INTEGERread-writecurrent
dsShdslRxDownstreamStuffBits
OBJECT-TYPE
This object defines the downstream stuff bits.
1.3.6.1.4.1.6296.9.6.1.1.3.1.14INTEGERread-writecurrent
dsShdslInitiate
OBJECT-TYPE
This object defines which STU initiates a startup. The default is STU-R initiates and STU-C waits.
1.3.6.1.4.1.6296.9.6.1.1.3.1.15INTEGER {default(0), co(1), cpe(2)}read-writecurrent
dsShdslFramerRxClockMode
OBJECT-TYPE
This object determines the source of the receive clock.
1.3.6.1.4.1.6296.9.6.1.1.3.1.16INTEGER {slave(2), internal(3)}read-writecurrent
dsShdslFramerRxPllMode
OBJECT-TYPE
This object enables or disables the internal PLL.
1.3.6.1.4.1.6296.9.6.1.1.3.1.17INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslSerialAtmCiuBufferSize
OBJECT-TYPE
This object enables the user to set the size of the framer buffer for serial ATM operation.
1.3.6.1.4.1.6296.9.6.1.1.3.1.18INTEGER {dsShdslLineParamsTable24(24), dsShdslLineParamsTable53(53)}read-writecurrent
dsShdslUtopiaL2TxAddress
OBJECT-TYPE
This object selects the appropriate UTOPIA Level 2 address for the transmit interface.
1.3.6.1.4.1.6296.9.6.1.1.3.1.19INTEGERread-onlycurrent
dsShdslUtopiaL2RxAddress
OBJECT-TYPE
This object selects the appropriate UTOPIA Level 2 address for the receive interface.
1.3.6.1.4.1.6296.9.6.1.1.3.1.20INTEGERread-onlycurrent
dsShdslTxFramerPulseDelay
OBJECT-TYPE
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the transmit frame pulse.
1.3.6.1.4.1.6296.9.6.1.1.3.1.21INTEGER {dsShdslLineParamsTable0(0), dsShdslLineParamsTable1(1), dsShdslLineParamsTable2(2), dsShdslLineParamsTable3(3), dsShdslLineParamsTable4(4), dsShdslLineParamsTable5(5), dsShdslLineParamsTable6(6), dsShdslLineParamsTable7(7)}read-writecurrent
dsShdslRxFramerPulseDelay
OBJECT-TYPE
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the receive frame pulse.
1.3.6.1.4.1.6296.9.6.1.1.3.1.22INTEGER {dsShdslLineParamsTable0(0), dsShdslLineParamsTable1(1), dsShdslLineParamsTable2(2), dsShdslLineParamsTable3(3), dsShdslLineParamsTable4(4), dsShdslLineParamsTable5(5), dsShdslLineParamsTable6(6), dsShdslLineParamsTable7(7)}read-writecurrent
dsShdslMultiFrameMode
OBJECT-TYPE
This object specifies the multi frame operational mode of the transceiver.
1.3.6.1.4.1.6296.9.6.1.1.3.1.23INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslEnable4or6MbpsBitrate
OBJECT-TYPE
This object specifies the operational state of the 4_6Mbps bit rate.
1.3.6.1.4.1.6296.9.6.1.1.3.1.24INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslTomDataWord1
OBJECT-TYPE
This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.
1.3.6.1.4.1.6296.9.6.1.1.3.1.25INTEGERread-writecurrent
dsShdslTomDataWord2
OBJECT-TYPE
This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.
1.3.6.1.4.1.6296.9.6.1.1.3.1.26INTEGERread-writecurrent
dsShdslTomDataWord3
OBJECT-TYPE
This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.
1.3.6.1.4.1.6296.9.6.1.1.3.1.27INTEGERread-writecurrent
dsShdslTomDataWord4
OBJECT-TYPE
This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.
1.3.6.1.4.1.6296.9.6.1.1.3.1.28INTEGERread-writecurrent
dsShdslSetReqSilenceMode
OBJECT-TYPE
This object enables a silent mode for the STU at the opposite end of the loop for approximately one minute. During the silent period, the STU that requested the silent mode could perform whatever operations it wants and the STU at the opposite end will remain in handshake.
1.3.6.1.4.1.6296.9.6.1.1.3.1.29INTEGER {disable(0), enable(4)}read-writecurrent
dsShdslSetIndividualRates1
OBJECT-TYPE
This item enables the user to individually enable or disable base rates for N=1 through N=16. The default is all rates enabled.
1.3.6.1.4.1.6296.9.6.1.1.3.1.30INTEGERread-writecurrent
dsShdslSetIndividualRates2
OBJECT-TYPE
This item enables the user to individually enable or disable base rates for N=17 through N=32. The default is all rates enabled.
1.3.6.1.4.1.6296.9.6.1.1.3.1.31INTEGERread-writecurrent
dsShdslSetIndividualRates3
OBJECT-TYPE
This item enables the user to individually enable or disable base rates for N=33 through N=36. The default is all rates enabled.
1.3.6.1.4.1.6296.9.6.1.1.3.1.32INTEGERread-writecurrent
dsShdslSatmCellDelineation
OBJECT-TYPE
This object enables the user to enable or disable cell delineation for serial ATM operation. This parameter should be set before a startup.
1.3.6.1.4.1.6296.9.6.1.1.3.1.33INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslFramerCellDropOnError
OBJECT-TYPE
This object determines whether cells are dropped, i.e., not passed to the host, or not dropped, i.e., passed to the host. This object must be set prior to startup.
1.3.6.1.4.1.6296.9.6.1.1.3.1.34INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslGearShiftType
OBJECT-TYPE
This object specifies the Gear Shift Type.
1.3.6.1.4.1.6296.9.6.1.1.3.1.35INTEGER {dsShdslLineParamsTable0(0), dsShdslLineParamsTable1(1)}read-writecurrent
dsShdslHsNsf
OBJECT-TYPE
This object enables or disables nonstandard Information fields for MP, MS, CL, and CLR messages, as defined in ITU-T G.994.1.bis.
1.3.6.1.4.1.6296.9.6.1.1.3.1.36INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslHsMaxBitsPerBaud
OBJECT-TYPE
This object specifies the maximum bit per baud.
1.3.6.1.4.1.6296.9.6.1.1.3.1.37INTEGER {dsShdslLineParamsTable1bits(1), dsShdslLineParamsTable2bits(2), default(3)}read-writecurrent
dsShdslHsCusId
OBJECT-TYPE
This object identifies the customer identification during handshaking, as described in ITU-T G.994.1.bis.
1.3.6.1.4.1.6296.9.6.1.1.3.1.38INTEGERread-writecurrent
dsShdslHsCusData0
OBJECT-TYPE
This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.
1.3.6.1.4.1.6296.9.6.1.1.3.1.39INTEGERread-writecurrent
dsShdslHsCusData1
OBJECT-TYPE
This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.
1.3.6.1.4.1.6296.9.6.1.1.3.1.40INTEGERread-writecurrent
dsShdslHsAnnexBType
OBJECT-TYPE
This object allows the customer to choose between support for Annex B, Annex B with Access Network Frequency Plan (ANFP), or both.
1.3.6.1.4.1.6296.9.6.1.1.3.1.41INTEGER {default(1), anfp(2), annexbOrAnfp(3)}read-writecurrent
dsShdslAutoRetrain
OBJECT-TYPE
Enables or disables auto-retrain.
1.3.6.1.4.1.6296.9.6.1.1.3.1.42INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslArCrcCheck
OBJECT-TYPE
Enables or disables auto-retrain based on CRC errors.
1.3.6.1.4.1.6296.9.6.1.1.3.1.43INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslArFramerSyncCheck
OBJECT-TYPE
Enables or disables auto-retrain based on framer synchronization.
1.3.6.1.4.1.6296.9.6.1.1.3.1.44INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslArSnrMarginCheck
OBJECT-TYPE
Enables or disables auto-retrain based on whether the S/N margin falls below a preset threshold.
1.3.6.1.4.1.6296.9.6.1.1.3.1.45INTEGER {disable(0), enable(1)}read-writecurrent
dsShdslArCrcThreshold
OBJECT-TYPE
Sets the threshold for the number of frames with CRC errors for autoretrain.
1.3.6.1.4.1.6296.9.6.1.1.3.1.46INTEGER (0..1024)read-writecurrent
dsShdslArSnrMarginThreshold
OBJECT-TYPE
Set the margin threshold for autoretrain.
1.3.6.1.4.1.6296.9.6.1.1.3.1.47INTEGER {dsShdslLineParamsTable1(1), dsShdslLineParamsTable2(2), dsShdslLineParamsTable3(3), dsShdslLineParamsTable4(4), dsShdslLineParamsTable5(5), dsShdslLineParamsTable6(6)}read-writecurrent
dsShdslArRetrainTime
OBJECT-TYPE
Sets the time over which the autoretrain parameters must be outside their normal ranges, so that an auto-retrain occurs.
1.3.6.1.4.1.6296.9.6.1.1.3.1.48INTEGER {dsShdslLineParamsTable1(1), dsShdslLineParamsTable2(2), dsShdslLineParamsTable3(3), dsShdslLineParamsTable4(4), dsShdslLineParamsTable5(5), dsShdslLineParamsTable6(6), dsShdslLineParamsTable7(7), dsShdslLineParamsTable8(8), dsShdslLineParamsTable9(9), dsShdslLineParamsTable10(10)}read-writecurrent
dsShdslOpStateTrapEnable
OBJECT-TYPE
Enables/disables trap indicating a change in op state.
1.3.6.1.4.1.6296.9.6.1.1.3.1.49INTEGER {enable(1), disable(2)}read-writecurrent
dsShdslTxFrmrDataClkEdge
OBJECT-TYPE
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, transmit data can be sampled upon either rising or falling edge of the transmit clock.
1.3.6.1.4.1.6296.9.6.1.1.3.1.50INTEGER {negative(0), positive(1)}read-writecurrent
dsShdslRxFrmrDataClkEdge
OBJECT-TYPE
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, receive data can be valid upon either rising or falling edge of the receive clock.
1.3.6.1.4.1.6296.9.6.1.1.3.1.51INTEGER {negative(0), positive(1)}read-writecurrent
dsShdslTxFrmrPulseClkEdge
OBJECT-TYPE
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.
1.3.6.1.4.1.6296.9.6.1.1.3.1.52INTEGER {negative(0), positive(1)}read-writecurrent
dsShdslRxFrmrPulseClkEdge
OBJECT-TYPE
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.
1.3.6.1.4.1.6296.9.6.1.1.3.1.53INTEGER {negative(0), positive(1)}read-writecurrent
dsShdslTxFrmrPulseLvl
OBJECT-TYPE
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).
1.3.6.1.4.1.6296.9.6.1.1.3.1.54INTEGER {low(0), high(1)}read-writecurrent
dsShdslRxFrmrPulseLvl
OBJECT-TYPE
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).
1.3.6.1.4.1.6296.9.6.1.1.3.1.55INTEGER {low(0), high(1)}read-writecurrent
dsShdslUtopiaDataBusWidth
OBJECT-TYPE
This parameter is used to specify width of UTOPIA data bus.
1.3.6.1.4.1.6296.9.6.1.1.3.1.56INTEGER {tx8Rx8(0), tx16Rx16(1), tx16Rx8(2), tx8Rx16(3)}read-onlycurrent
dsShdslFrmrOH
OBJECT-TYPE
This object specifies framer OverHead Channel.
1.3.6.1.4.1.6296.9.6.1.1.3.1.57INTEGER (0..65535)read-writecurrent
dsShdslLoopAttenCrossingTrapEnable
OBJECT-TYPE
This Parameter enables or disables the Trap for Loop Attenuation Threshold crossing.
1.3.6.1.4.1.6296.9.6.1.1.3.1.58INTEGER {enable(1), disable(2)}read-writecurrent
dsShdslSNRMarginCrossingTrapEnable
OBJECT-TYPE
This Parameter enables or disables the Trap for SNR Margin Threshold crossing.
1.3.6.1.4.1.6296.9.6.1.1.3.1.59INTEGER {enable(1), disable(2)}read-writecurrent
dsShdslFramerOHAndDefectsTrapEnable
OBJECT-TYPE
This Parameter enables or disables the Trap for Framer Overhead and Defects.
1.3.6.1.4.1.6296.9.6.1.1.3.1.60INTEGER {enable(1), disable(2)}read-writecurrent
dsShdslParametricTestInputFile
OBJECT-TYPE
Indicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified.
1.3.6.1.4.1.6296.9.6.1.1.3.1.61DisplayString (SIZE(0..56))read-writecurrent
dsShdslParamHybridLossTestStart
OBJECT-TYPE
Indicates Start bin for range of bins to be measured. The default value mentioned is an indicative value only, for exact value refer to document number DO-400523-AN and DO-401163-AN.
1.3.6.1.4.1.6296.9.6.1.1.3.1.62INTEGER (0..255)read-writecurrent
dsShdslParamHybridLossTestEnd
OBJECT-TYPE
Indicates End bin for range of bins to be measured. The default value mentioned is an indicative value only.
1.3.6.1.4.1.6296.9.6.1.1.3.1.63INTEGER (0..255)read-writecurrent
dsShdslSpanStatusExtnTable
OBJECT-TYPE
This table is a proprietary extension of hdsl2ShdslSpanStatusTable
1.3.6.1.4.1.6296.9.6.1.1.4not-accessiblecurrent
dsShdslSpanStatusExtnEntry
OBJECT-TYPE
An entry (conceptual row) in the dsShdslSpanStatusExtnTable. The Table is indexed by ifIndex.
1.3.6.1.4.1.6296.9.6.1.1.4.1not-accessiblecurrent
dsShdslStatusPMMSMaxLineRate
OBJECT-TYPE
This object provides the maximum PMMS rate the line is capable of achieving
1.3.6.1.4.1.6296.9.6.1.1.4.1.1Unsigned32 (0..4112000)read-onlycurrent
dsShdslStatus4WireHsMode
OBJECT-TYPE
Contains the current 4 Wire Handshake Mode Configured
1.3.6.1.4.1.6296.9.6.1.1.4.1.2INTEGER {standard(0), enhanced(1)}read-onlycurrent