MIBs Depot

CTRON-SSR-HARDWARE-MIB

Registered at
1.3.6.1.4.1.52.2501.1.1
1.3.6.1.4.1.52.2501.1.200
Last updated
2000-07-17 00:00
Organization
Cabletron Systems, Inc.
Revisions
2000-07-17 00:00, 2000-07-15 00:00, 2000-05-31 00:00, 2000-03-20 00:00, 1999-12-30 00:00, 1999-01-20 00:00, 1998-08-04 00:00
Namespace
enterasys
Source file
CTRON-SSR-HARDWARE-MIB
Digest
sha256:13e9bb96c480e6c3f1025ca3219574cca0ff0ae67ce445852d3ca92cd46d8a82

Description

This module defines a schema to access SSR hardware configuration.

Contact

Enterasys Networks 35 Industrial Way, P.O. Box 5005 Rochester, NH 03867-0505 (603) 332-9400 support@enterasys.com http://www.enterasys.com

Imports

FromSymbols
CTRON-SSR-SMI-MIBssrMibs
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter64, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CTRON-OIDS
CTRON-SSR-HARDWARE-MIB
CTRON-SSR-SMI-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
PowerSupplyBits
TEXTUAL-CONVENTION
The encoding of the bits are as follows : Each power supply in the system is represented by two bits. The lower bit reflecting the presence of the power supply and the higher bit representing it's state. A 1 reflects a properly working power supply a 0 one which is down. This encoding allows for a maximum of 16 power supplies. For example : The integer value 0x00000007 translates into 0 0 0 0 0 1 1 1 in bits | | | | | | | +- power supply 1 is present | | +--- power supply 1 is working normally | +----- power supply 2 is present +------- power supply 2 is down
current
SSRBackupCMState
TEXTUAL-CONVENTION
A enumeration that represents the state of the backup control module. A backup control module prom will boot the system firmware to an intermediate state and begins sending hello messages to the main cpu and assume the monitor(3) state. If the prom does not boot the backup control module, the active control module will report the status as inactive(2). inactive(2) indicates a failed state as it means the backup control module can not take over for the active control module. If the main cpu fails to respond to the backup control module's periodic status checks and the backup control module is in the standby(3) state, the backup control module will reset the active control module, then reset all line cards and then finish a normal boot sequence so that it becomes the master. At this point, the value of this object is active(5). Flows in the hardware must be reprogrammed and all control protocols will have to reestablish. An enterprise trap may also be sent. Normally, slot: CM will be the primary control module. CM/1 is the slot for the backup control module. If some other line card exists in slot CM/1 or no card exists, the state of this object is notInstalled(4).
current
SSRCmLedState
TEXTUAL-CONVENTION
A bit string that represents the status of the active Control Module. Each LED occupies a bit. The value 1 indicates LED is on, 0 is off. The integer value 0x00000015 translates into (bits): 0 0 0 0 1 1 1 1 | | | | | | | +- System OK -- SYS OK | | +--- Heartbeat -- HB | +----- Error -- ERR + ------ Diagnostic -- Diag
current
SSRInterfaceIndex
TEXTUAL-CONVENTION
A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub- layer must remain constant at least from one re- initialization of the entity's network management system to the next re-initialization.
current
SSRModuleStatus
TEXTUAL-CONVENTION
Current state of module. online indicates the normal state. Offline indicates a powered off or failed module. Modules may be powered off prior to hot swap.
current
SSRModuleType
TEXTUAL-CONVENTION
A unique value, greater than zero, for each module type supported by the SSR series of products.
current
SSRPortConnectorType
TEXTUAL-CONVENTION
A unique value, greater than zero, for each physical port type supported by the SSR series of products
current
SSRPortType
TEXTUAL-CONVENTION
A unique value, greater than zero, for each physical port type supported by the SSR series of products.
current
SSRSwitchingFabricInfo
TEXTUAL-CONVENTION
A bit string that represents the status of Switching Fabric in the shelf/chassis. Switching Fabric #1 is first 2 bits 0-1, #2 is 2-3. For example, given a 16 slot SSR 8600 which has one Switching Fabric in Switching Fabric Slot #1 (lowest full length midplane slot) the integer value 0x00000007 translates into (bits): 0 0 0 0 0 1 1 1 | | | | | | | +--- switching fabric #1 is present | | +----- switching fabric is primary | + ------ switching fabric #2 is present +--------- switching fabric is standby
current
SSRmemorySize
TEXTUAL-CONVENTION
An integer that represents the size of memory in Megabytes. -1 represents not-available or not-applicable value.
current
SSRserviceType
TEXTUAL-CONVENTION
A string that is unique to a module in production. This string is used by Cabletron Service and Manufacturing as to identify shipped inventory.
current

Objects

NameOIDSyntaxAccessStatus
sysHwGroup
OBJECT-IDENTITY
1.3.6.1.4.1.52.2501.1.1
sysHwNumSlots
OBJECT-TYPE
The number of slots present in the Shelf/Chassis.
1.3.6.1.4.1.52.2501.1.1.1INTEGER (0..64)read-onlycurrent
sysHwModuleTable
OBJECT-TYPE
A list of module entries.
1.3.6.1.4.1.52.2501.1.1.2not-accessiblecurrent
sysHwModuleEntry
OBJECT-TYPE
An entry containing management information applicable to a particular module.
1.3.6.1.4.1.52.2501.1.1.2.1not-accessiblecurrent
sysHwModuleSlotNumber
OBJECT-TYPE
The physical slot number of the module in the Shelf/Chassis.
1.3.6.1.4.1.52.2501.1.1.2.1.1INTEGER (1..65)read-onlycurrent
sysHwModuleType
OBJECT-TYPE
The physical module type.
1.3.6.1.4.1.52.2501.1.1.2.1.2SSRModuleTyperead-onlycurrent
sysHwModuleDesc
OBJECT-TYPE
The description of the module with it's version number etc. For the Control Module it should have the software version, the amount of dynamic RAM, flash RAM.
1.3.6.1.4.1.52.2501.1.1.2.1.3OCTET STRING (SIZE(0..255))read-onlycurrent
sysHwModuleNumPorts
OBJECT-TYPE
The number of physical ports on this Card/Module.
1.3.6.1.4.1.52.2501.1.1.2.1.4INTEGER (0..256)read-onlycurrent
sysHwModuleVersion
OBJECT-TYPE
The alpha-numeric version string for this Card/Module.
1.3.6.1.4.1.52.2501.1.1.2.1.5OCTET STRING (SIZE(1))read-onlycurrent
sysHwModuleMemory
OBJECT-TYPE
System Memory size available on the Module. Reports -1 if no memory exists on this module, such as power supplies.
1.3.6.1.4.1.52.2501.1.1.2.1.6SSRmemorySizeread-onlycurrent
sysHwModuleService
OBJECT-TYPE
The Cabletron service identifier string for this Card/Module.The board serial number is appended to the string too.
1.3.6.1.4.1.52.2501.1.1.2.1.8SSRserviceTyperead-onlycurrent
sysHwModuleStatus
OBJECT-TYPE
The current status of this module, online or offline.
1.3.6.1.4.1.52.2501.1.1.2.1.9SSRModuleStatusread-onlycurrent
sysHwPortTable
OBJECT-TYPE
A list of module entries.
1.3.6.1.4.1.52.2501.1.1.3not-accessiblecurrent
sysHwPortEntry
OBJECT-TYPE
An entry containing management information applicable to a particular module.
1.3.6.1.4.1.52.2501.1.1.3.1not-accessiblecurrent
sysHwPortSlotNumber
OBJECT-TYPE
The physical slot number of the module in the Chassis.
1.3.6.1.4.1.52.2501.1.1.3.1.1INTEGER (1..255)read-onlycurrent
sysHwPortNumber
OBJECT-TYPE
The port number of the physical port in the Card/Module.
1.3.6.1.4.1.52.2501.1.1.3.1.2INTEGER (1..255)read-onlycurrent
sysHwPortType
OBJECT-TYPE
The physical port type.
1.3.6.1.4.1.52.2501.1.1.3.1.3SSRPortTyperead-onlycurrent
sysHwPortConnectorType
OBJECT-TYPE
The physical port connector type.
1.3.6.1.4.1.52.2501.1.1.3.1.4SSRPortConnectorTyperead-onlycurrent
sysHwPortIfIndex
OBJECT-TYPE
The value of ifIndex used to access this port in the Interface MIB.
1.3.6.1.4.1.52.2501.1.1.3.1.5SSRInterfaceIndexread-onlycurrent
sysHwPowerSupply
OBJECT-TYPE
The number and status of power supplies powering the Shelf/Chassis.
1.3.6.1.4.1.52.2501.1.1.4PowerSupplyBitsread-onlycurrent
sysHwFan
OBJECT-TYPE
The current state of the fans located inside the Shelf/Chassis.
1.3.6.1.4.1.52.2501.1.1.5INTEGER {working(1), notWorking(2), unknown(3)}read-onlycurrent
sysHwTemperature
OBJECT-TYPE
The current temperature status of the Shelf/Chassis.
1.3.6.1.4.1.52.2501.1.1.6INTEGER {normal(1), outOfRange(2), unknown(3)}read-onlycurrent
sysHwChassisId
OBJECT-TYPE
Operator defined serial number for this particular chassis/shelf.
1.3.6.1.4.1.52.2501.1.1.7OCTET STRING (SIZE(0..255))read-onlycurrent
sysHwTotalInOctets
OBJECT-TYPE
The total number of octets into the switch.
1.3.6.1.4.1.52.2501.1.1.10Counter64read-onlydeprecated
sysHwTotalOutOctets
OBJECT-TYPE
The total number of octets out of the switch.
1.3.6.1.4.1.52.2501.1.1.11Counter64read-onlydeprecated
sysHwTotalInFrames
OBJECT-TYPE
The total number of frames into the switch.
1.3.6.1.4.1.52.2501.1.1.12Counter64read-onlydeprecated
sysHwTotalOutFrames
OBJECT-TYPE
The total number of frames out of the switch.
1.3.6.1.4.1.52.2501.1.1.13Counter64read-onlydeprecated
sysHwTotalL2SwitchedFrames
OBJECT-TYPE
The current number of frames switched at Layer 2 (transport).
1.3.6.1.4.1.52.2501.1.1.14Counter64read-onlydeprecated
sysHwTotalL3SwitchedFrames
OBJECT-TYPE
The current number of frames switched at IETF Layers 3 (transport) and 4 (application).
1.3.6.1.4.1.52.2501.1.1.15Counter64read-onlydeprecated
sysHwSwitchingFabric
OBJECT-TYPE
Status of Switching Fabric in shelf/chassis.
1.3.6.1.4.1.52.2501.1.1.19SSRSwitchingFabricInforead-onlycurrent
sysHwControlModuleLED
OBJECT-TYPE
Status of the shelf/chassis Active Control Module's four LED displays.
1.3.6.1.4.1.52.2501.1.1.20SSRCmLedStateread-onlycurrent
sysHwControlModuleBackupState
OBJECT-TYPE
Status of the the backup Control Module as interpreted from the active control module. CLI: system show hardware will present the following data: Redundant CPU slot : Not present
1.3.6.1.4.1.52.2501.1.1.21SSRBackupCMStateread-onlycurrent
sysHwLastHotSwapEvent
OBJECT-TYPE
The value of sysUpTime when the last hotswap of a physical module event occured.
1.3.6.1.4.1.52.2501.1.1.22TimeTicksread-onlycurrent
hwConformance
OBJECT-IDENTITY
1.3.6.1.4.1.52.2501.1.200.2
hwCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.52.2501.1.200.2.1
hwGroups
OBJECT-IDENTITY
1.3.6.1.4.1.52.2501.1.200.2.2

Conformance

NameOIDStatus
hwConfGroupV10
OBJECT-GROUP
A set of managed objects that make up version 1.0 of the SSR Hardware mib.
1.3.6.1.4.1.52.2501.1.200.2.2.1deprecated
hwComplianceV10
MODULE-COMPLIANCE
The compliance statement for the SSR-HARDWARE-MIB.
1.3.6.1.4.1.52.2501.1.200.2.2.1.1deprecated
hwConfGroupV11
OBJECT-GROUP
A set of managed objects that make up version 1.1 of the SSR Hardware mib.
1.3.6.1.4.1.52.2501.1.200.2.2.2deprecated
hwComplianceV11
MODULE-COMPLIANCE
The compliance statement for the SSR-HARDWARE-MIB.
1.3.6.1.4.1.52.2501.1.200.2.2.2.2deprecated
hwComplianceV12
MODULE-COMPLIANCE
The compliance statement for the SSR-HARDWARE-MIB.
1.3.6.1.4.1.52.2501.1.200.2.2.2.3deprecated
hwComplianceV30
MODULE-COMPLIANCE
The compliance statement for the SSR-HARDWARE-MIB.
1.3.6.1.4.1.52.2501.1.200.2.2.2.4current
hwConfGroupV12
OBJECT-GROUP
A set of managed objects that make up version 1.2 of the SSR Hardware mib.
1.3.6.1.4.1.52.2501.1.200.2.2.3deprecated
hwConfGroupV30
OBJECT-GROUP
A set of managed objects that make up version 3.0 of the SSR Hardware mib.
1.3.6.1.4.1.52.2501.1.200.2.2.4current