MIBs Depot

CTRON-AP3000-MIB

Registered at
1.3.6.1.4.1.52
Last updated
2007-10-30 18:45
Organization
Enterasys Networks, Inc
Revisions
2007-10-30 18:45
Namespace
enterasys
Source file
CTRON-AP3000-MIB
Digest
sha256:f459136523f3d8793f86dd386418717e21b86af8bd2581d44930abc6e8b54f33

Description

This mib module defines a portion of the SNMP enterprise MIBs under Enterasys Networks enterprise OID as an extension to the Enterasys AP3000 MIB. This Enterasys Networks Proprietary MIB was designed to be used for read-write access to configuration objects in AP3000.

Contact

Postal: Enterasys Networks 35 Industrial Way, P.O. Box 5005 Rochester, NH 03867-0505 Phone: +1 603 332 9400 E-mail: support@enterasys.com WWW: http://www.enterasys.com

Imports

FromSymbols
IF-MIBifIndex
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMICounter32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, enterprises, iso, mgmt
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CTRON-AP3000-MIB
IANAifType-MIB
IF-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Under this module's arcs

Where the registration tree carries on below this module.

ArcNameModule
1.3.6.1.4.1.52.1commsDeviceIRM-OIDS
1.3.6.1.4.1.52.2layerMgmtIRM-OIDS
1.3.6.1.4.1.52.3namingTreeCTRON-OIDS
1.3.6.1.4.1.52.4mibs
1.3.6.1.4.1.52.5v2conformanceCTRON-OIDS
1.3.6.1.4.1.52.6trapDefinitionsCTRON-OIDS
1.3.6.1.4.1.52.1011els100CTELS100-NG-MIB
1.3.6.1.4.1.52.2501ssrCTRON-SSR-SMI-MIB

Textual conventions

NameOIDSyntaxAccessStatus
DisplayString
type
MacAddress
type
TruthValue
type

Objects

NameOIDSyntaxAccessStatus
cabletron
OBJECT-IDENTITY
1.3.6.1.4.1.52
mibs
OBJECT-IDENTITY
1.3.6.1.4.1.52.4
comPortMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.1
comPortControl
OBJECT-TYPE
The administrative enable/disable state for COM Port Control in a System.
1.3.6.1.4.1.52.4.13.1.1INTEGER {enabled(1), disabled(2)}read-writecurrent
macFilterMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.2
macFilterTable
OBJECT-TYPE
Table of status information about each configured MAC Filtering Entry.
1.3.6.1.4.1.52.4.13.2.1not-accessibledeprecated
macFilterEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of MAC Filter.
1.3.6.1.4.1.52.4.13.2.1.1not-accessibledeprecated
macFilterIndex
OBJECT-TYPE
Filter index.
1.3.6.1.4.1.52.4.13.2.1.1.1Integer32 (1..2147483647)not-accessibledeprecated
macFilterAddress
OBJECT-TYPE
This values indicates the MAC address of the MAC Filter entry.
1.3.6.1.4.1.52.4.13.2.1.1.2MacAddressread-writedeprecated
macFilterAllowedToGo
OBJECT-TYPE
The administrative allow/deny state for that specified MAC Filter Entry.
1.3.6.1.4.1.52.4.13.2.1.1.3INTEGER {allow(1), deny(2)}read-writedeprecated
macFilterOpeStatus
OBJECT-TYPE
This object indicates the status of this entry. other(0) - this entry is currently in use but the conditions under which it will remain so differ from the following values. valid(1) - this value to indicate this entry is currently in used. invalid(2) - write this value to the corresponding entry, the whole entry will be removed. Since the order of entry shall be re-order while it has been deleted. To re-freshed the whole table is recommended for new index. create(3) - write this value to indicate that the new MAC address will be added after next writing MAC address to that new entry. The adding action will be taken on the index that grater than 1.
1.3.6.1.4.1.52.4.13.2.1.1.4INTEGER {other(0), valid(1), invalid(2), create(3)}read-createdeprecated
apMacFilterControl
OBJECT-TYPE
This value indicates the control of the MAC filter setting.
1.3.6.1.4.1.52.4.13.2.2INTEGER {enabled(1), disabled(2)}read-writedeprecated
apvMacFilterOperateTable
OBJECT-TYPE
The Table used to manage the function in MAC Filter Table.
1.3.6.1.4.1.52.4.13.2.3not-accessiblecurrent
apvMacFilterOperateEntry
OBJECT-TYPE
An entry in the table, containing information about configuration in one VAP of the AP.
1.3.6.1.4.1.52.4.13.2.3.1not-accessiblecurrent
apvMacFilterPermission
OBJECT-TYPE
This values indicates the Permission on all the active filter entry for each Vap. The negative permission will be applied on any inactive entry or any MAC that is not in the table.
1.3.6.1.4.1.52.4.13.2.3.1.1INTEGER {allowed(1), denied(2)}read-writecurrent
apvMacFilterAddressToAdd
OBJECT-TYPE
This values indicates the MAC address to be added to the local MAC filter table as an active entry for each Vap.
1.3.6.1.4.1.52.4.13.2.3.1.2OCTET STRINGread-writecurrent
apvMacFilterTable
OBJECT-TYPE
Table of status information about each configured MAC Address Filtering Entry.
1.3.6.1.4.1.52.4.13.2.4not-accessiblecurrent
apvMacFilterEntry
OBJECT-TYPE
An entry in the table, containing information about configuration in one radio of the AP. MacFilterEntry is created and managed using localMACFilterMgnt Table.
1.3.6.1.4.1.52.4.13.2.4.1not-accessiblecurrent
apvMacFilterIndex
OBJECT-TYPE
MAC Filter index in each VAP.
1.3.6.1.4.1.52.4.13.2.4.1.1Integer32 (1..2147483647)not-accessiblecurrent
apvMacFilterAddress
OBJECT-TYPE
This values indicates the MAC address of the filter entry.
1.3.6.1.4.1.52.4.13.2.4.1.2MacAddressread-onlycurrent
apvMacFilterActivity
OBJECT-TYPE
This value indicates the Activity of the MAC table entry by the filter permission. If allow(1), the filter permission will be applied to the MAC address. If denied(2), the filter permission will not be applied to the MAC address. If delete_entry(3), the filter entry will be deleted.
1.3.6.1.4.1.52.4.13.2.4.1.3INTEGER {allow(1), denied(2), deleteEntry(3)}read-writecurrent
qosMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.3
qosModeControl
OBJECT-TYPE
The administrative status and control of the QoS mode for the QoS management.
1.3.6.1.4.1.52.4.13.3.1INTEGER {qosoff(1), qossa(2), qosda(3), qosether(4), qos8021p(5)}read-writecurrent
qosMACTypeTable
OBJECT-TYPE
Table of status information about each configured MAC Type Entry for the QoS Management.
1.3.6.1.4.1.52.4.13.3.2not-accessiblecurrent
qosMACTypeEntry
OBJECT-TYPE
An entry in the table, containing information about configuration MAC Type Entry for the QoS Management.
1.3.6.1.4.1.52.4.13.3.2.1not-accessiblecurrent
qosMACTypeIndex
OBJECT-TYPE
Qos MAC Type index.
1.3.6.1.4.1.52.4.13.3.2.1.1Integer32 (1..2147483647)not-accessiblecurrent
qosMACTypeAddress
OBJECT-TYPE
This values indicates the MAC address of that specified index in the entry.
1.3.6.1.4.1.52.4.13.3.2.1.2MacAddressread-writecurrent
qosMACTypePriority
OBJECT-TYPE
This values indicates the level of priority of that specified MAC Address in entry.
1.3.6.1.4.1.52.4.13.3.2.1.3Integer32 (0..7)read-writecurrent
qosMACTypeOpeStatus
OBJECT-TYPE
This object indicates the status of this entry. other(0) - this entry is currently in use but the conditions under which it will remain so differ from the following values. valid(1) - this value to indicate this entry is currently in used. invalid(2) - write this value to the corresponding entry, the whole entry will be removed. Since the order of entry shall be re-order while it has been deleted. To re-freshed the whole table is recommended for new index. create(3) - write this value to indicate that the new MAC address will be added after next writing MAC address to that new entry. The adding action will be taken on the index that grater than 1.
1.3.6.1.4.1.52.4.13.3.2.1.4INTEGER {other(0), valid(1), invalid(2), create(3)}read-createcurrent
qosEtherTypeTable
OBJECT-TYPE
Table of status information about each configured Ether Type Entry for QoS Management.
1.3.6.1.4.1.52.4.13.3.3not-accessiblecurrent
qosEtherTypeEntry
OBJECT-TYPE
An entry in the table, containing information about configuration Ether Type for QoS Management.
1.3.6.1.4.1.52.4.13.3.3.1not-accessiblecurrent
qosEtherTypeIndex
OBJECT-TYPE
Qos Ether Type index in the table.
1.3.6.1.4.1.52.4.13.3.3.1.1Integer32not-accessiblecurrent
qosEtherTypeHexValue
OBJECT-TYPE
The Hex Value to indicate the type of Ether of that specified index in the entry.
1.3.6.1.4.1.52.4.13.3.3.1.2OCTET STRING (SIZE(4))read-writecurrent
qosEtherTypePriority
OBJECT-TYPE
This values indicates the level of priority of that specified MAC Address in entry.
1.3.6.1.4.1.52.4.13.3.3.1.3Integer32 (0..7)read-writecurrent
qosEtherTypeOpeStatus
OBJECT-TYPE
This object indicates the status of this entry. other(0) - this entry is currently in use but the conditions under which it will remain so differ from the following values. valid(1) - this value to indicate this entry is currently in used. invalid(2) - write this value to the corresponding entry, the whole entry will be removed. Since the order of entry shall be re-order while it has been deleted. To re-freshed the whole table is recommended for new index. create(3) - write this value to indicate that the new Ether Value will be added after next writing Ether Type Value to that new entry. The adding action will be taken on the index that grater than 1.
1.3.6.1.4.1.52.4.13.3.3.1.4INTEGER {other(0), valid(1), invalid(2), create(3)}read-createcurrent
qosQueueingMode
OBJECT-TYPE
The administrative control of the QoS Queuing mode for the QoS management.
1.3.6.1.4.1.52.4.13.3.4INTEGER {weighted-fair(1), strict-priority(2)}read-writecurrent
qosSVPStatus
OBJECT-TYPE
The administrative enable/disable state for SVP.
1.3.6.1.4.1.52.4.13.3.5INTEGER {enabled(1), disabled(2)}read-writecurrent
linkQualityMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.4
linkQualityTable
OBJECT-TYPE
Table of status information about the radio Interface Link Quality Entry.
1.3.6.1.4.1.52.4.13.4.1not-accessiblecurrent
linkQualityEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of the radio Interface Link Quality.
1.3.6.1.4.1.52.4.13.4.1.1not-accessiblecurrent
linkQualityRadioIndex
OBJECT-TYPE
This is the value to define the index of the radio interface.
1.3.6.1.4.1.52.4.13.4.1.1.1Integer32 (1..2147483647)not-accessiblecurrent
linkQualityStaIndex
OBJECT-TYPE
This is value to define the index of link station.
1.3.6.1.4.1.52.4.13.4.1.1.2Integer32 (1..2147483647)not-accessiblecurrent
linkQualityStaMacAddress
OBJECT-TYPE
This values indicates the MAC address of the link station.
1.3.6.1.4.1.52.4.13.4.1.1.3MacAddressread-onlycurrent
linkQualityStaRssi
OBJECT-TYPE
This values indicates the percentage RSSI of the link station.
1.3.6.1.4.1.52.4.13.4.1.1.4Integer32 (0..100)read-onlycurrent
apSnmpMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.5
trapControl
OBJECT-TYPE
The administrative enable/disable state for SNMP Trap Control in a System.
1.3.6.1.4.1.52.4.13.5.1INTEGER {enabled(1), disabled(2)}read-writecurrent
trapConfiguration
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.5.2
trapSysSystemUp
OBJECT-TYPE
The administrative enable/disable state for SNMP sysSystemUp trap.
1.3.6.1.4.1.52.4.13.5.2.1INTEGER {enabled(1), disabled(2)}read-writecurrent
trapSysSystemDown
OBJECT-TYPE
The administrative enable/disable state for SNMP sysSystemDown trap.
1.3.6.1.4.1.52.4.13.5.2.2INTEGER {enabled(1), disabled(2)}read-writecurrent
trapSysRadiusServerChanged
OBJECT-TYPE
The administrative enable/disable state for SNMP sysRadiusServerChanged trap.
1.3.6.1.4.1.52.4.13.5.2.3INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot11StationAssociation
OBJECT-TYPE
The administrative enable/disable state for SNMP dot11StationAssociation trap.
1.3.6.1.4.1.52.4.13.5.2.4INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot11StationReAssociation
OBJECT-TYPE
The administrative enable/disable state for SNMP dot11StationReAssociation trap.
1.3.6.1.4.1.52.4.13.5.2.5INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot11StationAuthentication
OBJECT-TYPE
The administrative enable/disable state for SNMP dot11StationAuthentication trap.
1.3.6.1.4.1.52.4.13.5.2.6INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot11StationRequestFail
OBJECT-TYPE
The administrative enable/disable state for SNMP dot11StationRequestFail trap.
1.3.6.1.4.1.52.4.13.5.2.7INTEGER {enabled(1), disabled(2)}read-writecurrent
trapLocalMacAddrAuthFail
OBJECT-TYPE
The administrative enable/disable state for SNMP localMacAddrAuthFail trap.
1.3.6.1.4.1.52.4.13.5.2.9INTEGER {enabled(1), disabled(2)}read-writecurrent
trapLocalMacAddrAuthSuccess
OBJECT-TYPE
The administrative enable/disable state for SNMP localMacAddrAuthSuccess trap.
1.3.6.1.4.1.52.4.13.5.2.10INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot1xAuthNotInitiated
OBJECT-TYPE
The administrative enable/disable state for SNMP dot1xAuthNotInitiated trap.
1.3.6.1.4.1.52.4.13.5.2.11INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot1xAuthSuccess
OBJECT-TYPE
The administrative enable/disable state for SNMP dot1xAuthSuccess trap.
1.3.6.1.4.1.52.4.13.5.2.12INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot1xAuthFail
OBJECT-TYPE
The administrative enable/disable state for SNMP dot1xAuthFail trap.
1.3.6.1.4.1.52.4.13.5.2.13INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot1xMacAddrAuthSuccess
OBJECT-TYPE
The administrative enable/disable state for SNMP dot1xMacAddrAuthSuccess trap.
1.3.6.1.4.1.52.4.13.5.2.14INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot1xMacAddrAuthFail
OBJECT-TYPE
The administrative enable/disable state for SNMP dot1xMacAddrAuthFail trap.
1.3.6.1.4.1.52.4.13.5.2.15INTEGER {enabled(1), disabled(2)}read-writecurrent
trapPppLogonFail
OBJECT-TYPE
The administrative enable/disable state for SNMP pppLogonFail trap.
1.3.6.1.4.1.52.4.13.5.2.16INTEGER {enabled(1), disabled(2)}read-writecurrent
trapIappStationRoamedFrom
OBJECT-TYPE
The administrative enable/disable state for SNMP iappStationRoamedFrom trap.
1.3.6.1.4.1.52.4.13.5.2.17INTEGER {enabled(1), disabled(2)}read-writecurrent
trapIappStationRoamedTo
OBJECT-TYPE
The administrative enable/disable state for SNMP iappStationRoamedFrom trap.
1.3.6.1.4.1.52.4.13.5.2.18INTEGER {enabled(1), disabled(2)}read-writecurrent
trapIappContextDataSent
OBJECT-TYPE
The administrative enable/disable state for SNMP iappContextDataSent trap.
1.3.6.1.4.1.52.4.13.5.2.19INTEGER {enabled(1), disabled(2)}read-writecurrent
trapSntpServerFail
OBJECT-TYPE
The administrative enable/disable state for SNMP sntpServerFail trap.
1.3.6.1.4.1.52.4.13.5.2.20INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot11InterfaceAFail
OBJECT-TYPE
The administrative enable/disable state for SNMP dot11InterfaceAFail trap.
1.3.6.1.4.1.52.4.13.5.2.21INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot11InterfaceGFail
OBJECT-TYPE
The administrative enable/disable state for SNMP dot11InterfaceGFail trap.
1.3.6.1.4.1.52.4.13.5.2.22INTEGER {enabled(1), disabled(2)}read-writecurrent
trapDot11WirelessSTPDetection
OBJECT-TYPE
The administrative enable/disable state for SNMP dot11WirelessSTPDetection trap.
1.3.6.1.4.1.52.4.13.5.2.23INTEGER {enabled(1), disabled(2)}read-writecurrent
apSnmpTrapDestinationTable
OBJECT-TYPE
Table of descriptive and status information about configuration of each trap receiving server.
1.3.6.1.4.1.52.4.13.5.3not-accessiblecurrent
apSnmpTrapDestinationEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of one trap receiving server.
1.3.6.1.4.1.52.4.13.5.3.1not-accessiblecurrent
apSnmpTrapDestinationIndex
OBJECT-TYPE
Index of the Trap Destination Table.
1.3.6.1.4.1.52.4.13.5.3.1.1INTEGER (1..4)not-accessiblecurrent
apSnmpTrapDestinationCommunity
OBJECT-TYPE
The SNMP Trap Community
1.3.6.1.4.1.52.4.13.5.3.1.2DisplayString (SIZE(0..32))read-writecurrent
apSnmpTrapDestinationIP
OBJECT-TYPE
The IP address of the trap receiving server.
1.3.6.1.4.1.52.4.13.5.3.1.3IpAddressread-writecurrent
apSnmpTrapDestinationState
OBJECT-TYPE
This value indicates whether the trap receiving server is enabled.
1.3.6.1.4.1.52.4.13.5.3.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
apSnmpCommunityReadOnly
OBJECT-TYPE
The SNMP Read Only Community. The value if read, will only show ******.
1.3.6.1.4.1.52.4.13.5.4DisplayString (SIZE(0..32))read-writecurrent
apSnmpCommunityReadWrite
OBJECT-TYPE
The SNMP Read Write Community. The value if read, will only show *****.
1.3.6.1.4.1.52.4.13.5.5DisplayString (SIZE(0..32))read-writecurrent
apSnmpVersionFilter
OBJECT-TYPE
To set the version-filter of SNMP.
1.3.6.1.4.1.52.4.13.5.6INTEGER {enableSNMPv1SNMPv2c(1), disableSNMPv1SNMPv2c(2)}read-writecurrent
sysEntity
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.6
swHardwareVer
OBJECT-TYPE
Hardware version of the main board.
1.3.6.1.4.1.52.4.13.6.1DisplayString (SIZE(0..20))read-onlycurrent
swBootRomVer
OBJECT-TYPE
Boot ROM code version of the main board.
1.3.6.1.4.1.52.4.13.6.2DisplayString (SIZE(0..20))read-onlycurrent
swOpCodeVer
OBJECT-TYPE
Operation code version of the main board.
1.3.6.1.4.1.52.4.13.6.3DisplayString (SIZE(0..20))read-onlycurrent
swSerialNumber
OBJECT-TYPE
Serial Number of the Access Point.
1.3.6.1.4.1.52.4.13.6.4DisplayString (SIZE(0..20))read-onlycurrent
swProductName
OBJECT-TYPE
The Product Name of the Access Point.
1.3.6.1.4.1.52.4.13.6.5DisplayString (SIZE(0..20))read-onlycurrent
swCountrySetting
OBJECT-TYPE
The current CountryCode Setting of the Access Point.
1.3.6.1.4.1.52.4.13.6.6DisplayString (SIZE(0..255))read-onlycurrent
apSecurityMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.7
apRadioSecurityTable
OBJECT-TYPE
Table of descriptive and status information about configuration of each radio in terms of security settings.
1.3.6.1.4.1.52.4.13.7.1not-accessiblecurrent
apRadioSecurityEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of one radio of the AP.
1.3.6.1.4.1.52.4.13.7.1.1not-accessiblecurrent
apRadioSecurityIndex
OBJECT-TYPE
Radio Index for security settings.
1.3.6.1.4.1.52.4.13.7.1.1.1Integer32 (1..2147483647)not-accessiblecurrent
apRadioSecurityWEPAuthType
OBJECT-TYPE
This value indicates the type of WEP authentication in use for this radio interface. opensystem(0) Set authentication open sharedkey(1) Set authentication shared wpa(2) Set WPA Mode wpapsk(3) Set WPA-PSK Mode wpa-wpa2-mixed(4) Set WPA-WPA2-Mixed Mode wpawpa2pskmixed(5) Set WPA-WPA2 PSK Mixed Mode wpa2(6) Set WPA2 Mode wpa2psk(7) Set WPA2-PSK Mode
1.3.6.1.4.1.52.4.13.7.1.1.2INTEGER {opensystem(0), sharedkey(1), wpa(2), wpapsk(3), wpawpa2mixed(4), wpawpa2pskmixed(5), wpa2(6), wpa2psk(7)}read-writecurrent
apRadioSecuritySharedKeyLen
OBJECT-TYPE
This value indicates the shared key length for this radio interface.
1.3.6.1.4.1.52.4.13.7.1.1.3INTEGER {none(0), sixtyFour(1), oneHundredTwentyEight(2), oneHundredFiftyTwo(3)}read-onlycurrent
apRadioSecurityWPAMode
OBJECT-TYPE
This value indicates the state of WPA for this radio interface.
1.3.6.1.4.1.52.4.13.7.1.1.4INTEGER {supported(0), required(1), notSupported(2)}read-writecurrent
apRadioSecurityWPAKeyType
OBJECT-TYPE
This value indicates the type of WPA Key Management in use for this radio interface.
1.3.6.1.4.1.52.4.13.7.1.1.5INTEGER {dot1x(0), presharedkey(1)}read-writecurrent
apRadioSecurityWPACipher
OBJECT-TYPE
This value indicates the type of WPA Cipher in use for this radio interface.
1.3.6.1.4.1.52.4.13.7.1.1.6INTEGER {wep(0), tkip(1), aes(2)}read-writeobsolete
apRadioSecurityWPAPSKType
OBJECT-TYPE
This value indicates the type of WPA Pre Shared Key in use for this radio interface.
1.3.6.1.4.1.52.4.13.7.1.1.7INTEGER {hex(0), alphanumeric(1)}read-writecurrent
apRadioSecurityWPAPSK
OBJECT-TYPE
This value indicates WPA Pre Shared Key in use for this radio interface.
1.3.6.1.4.1.52.4.13.7.1.1.8DisplayString (SIZE(0..80))read-writecurrent
apRadioSecurityWEPKeyType
OBJECT-TYPE
This value indicates the type of WEP Key in use for this radio interface.
1.3.6.1.4.1.52.4.13.7.1.1.9INTEGER {hexadecimal(0), alphanumeric(1)}read-writecurrent
apRadioSecurityWEPEnabled
OBJECT-TYPE
This value indicates whether WEP is enabled.
1.3.6.1.4.1.52.4.13.7.1.1.10TruthValueread-writecurrent
apRadioSecurityWPACipherSuite
OBJECT-TYPE
This value indicates the type of WPA Cipher Suite in use for this radio interface.
1.3.6.1.4.1.52.4.13.7.1.1.11INTEGER {aesccmp(0), tkip(1), wep(2)}read-writecurrent
apRadioApSecurityWPAPreAuthentication
OBJECT-TYPE
Whether Pre-Authentication is enabled.
1.3.6.1.4.1.52.4.13.7.1.1.12INTEGER {enabled(1), disabled(2)}read-writecurrent
apRadioApSecurityWPAPmksaLifetime
OBJECT-TYPE
The number (in minutes) for Pmksa-Lifetime.
1.3.6.1.4.1.52.4.13.7.1.1.13INTEGER (0..14400)read-writecurrent
apSecuritySsh
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.7.2
apSecuritySshServerEnabled
OBJECT-TYPE
This value indicates whether SSH server is enabled.
1.3.6.1.4.1.52.4.13.7.2.1TruthValueread-writecurrent
apSecuritySshServerPort
OBJECT-TYPE
This value indicates SSH server's port number.
1.3.6.1.4.1.52.4.13.7.2.2Integer32read-writecurrent
apSecuritySshTelnetServerEnabled
OBJECT-TYPE
This value indicates whether telnet server is enabled.
1.3.6.1.4.1.52.4.13.7.2.3TruthValueread-writecurrent
apRadioInterfaceMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.8
enterpriseApRadioTable
OBJECT-TYPE
Table of descriptive and status information about configuration of each radio.
1.3.6.1.4.1.52.4.13.8.2not-accessiblecurrent
enterpriseApRadioEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of one radio of the AP.
1.3.6.1.4.1.52.4.13.8.2.1not-accessiblecurrent
enterpriseApRadioIndex
OBJECT-TYPE
Radio Index for configuration.
1.3.6.1.4.1.52.4.13.8.2.1.1Integer32 (1..2147483647)not-accessiblecurrent
enterpriseApRadioAutoChannel
OBJECT-TYPE
This value indicates whether auto channel selection is enabled or not for this radio interface
1.3.6.1.4.1.52.4.13.8.2.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApRadioTransmitPower
OBJECT-TYPE
This value indicates the transmit power for this radio interface.
1.3.6.1.4.1.52.4.13.8.2.1.3INTEGER {full(1), half(2), quarter(3), eighth(4), min(5)}read-writecurrent
enterpriseApRadioTurboMode
OBJECT-TYPE
This value indicates whether turbo mode is enabled for this radio interface.
1.3.6.1.4.1.52.4.13.8.2.1.4INTEGER {enabled(1), disabled(2), invalid(3)}read-writecurrent
enterpriseApRadioDataRate
OBJECT-TYPE
This value indicates the data rate for this radio interface. Radio interface A operates at 6, 9, 12, 18, 24, 36, 48, 54. Radio interface G operates all listed data rates. The auto setting will attempt to set the best data rate for the interface
1.3.6.1.4.1.52.4.13.8.2.1.5INTEGER {oneMbps(1), twoMbps(2), fiveAndHalfMbps(5), sixMbps(6), nineMbps(9), elevenMbps(11), twelveMbps(12), eighteenMbps(18), twentyFourMbps(24), thirtySixMbps(36), fourtyEightMbps(48), fiftyFourMbps(54), auto(255)}read-writecurrent
enterpriseApRadioGMode
OBJECT-TYPE
This value indicates the radio mode for the 802.11g radio. This setting is only valid for the 802.11g interface.
1.3.6.1.4.1.52.4.13.8.2.1.6INTEGER {bOnly(1), gOnly(2), bg(3), invalid(4)}read-writecurrent
enterpriseApRadioAntennaMode
OBJECT-TYPE
This value indicates the antenna mode in use for the G-radio. The values are interpreted as follows: both(1) means use both built-in antennas, left(2) means use left side. right(3) means use right side. invalid(4) means not support. This setting is only valid for the 802.11g interface.
1.3.6.1.4.1.52.4.13.8.2.1.7INTEGER {both(1), left(2), right(3), invalid(4)}read-writecurrent
rogueApState
OBJECT-TYPE
This value is used to enable/disable Rogue Ap Detection for this radio interface.
1.3.6.1.4.1.52.4.13.8.2.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
rogueApInterval
OBJECT-TYPE
How often to scan for Rogue Aps. The interval in minutes, with default of 720(minutes).
1.3.6.1.4.1.52.4.13.8.2.1.9INTEGER (30..10080)read-writecurrent
rogueApDuration
OBJECT-TYPE
How long to scan each channel (in milliseconds). A longer duration will yield more complete results. A shorter duration will allow clients a better chance of remaining connected. Default value is 350(milliseconds).
1.3.6.1.4.1.52.4.13.8.2.1.10INTEGER (200..1000)read-writecurrent
rogueApScanNow
OBJECT-TYPE
When writing the value to enable, the AP will trigger the Rouge AP scan function. The value will always return disable(2).
1.3.6.1.4.1.52.4.13.8.2.1.11INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApRadioAntennaModeControl
OBJECT-TYPE
This value indicates which antenna is in use for the radio Interface. The values are interpreted as follows: fixed(1) specify to use built-in antennas, external(2) specify to use one external antenna.
1.3.6.1.4.1.52.4.13.8.2.1.12INTEGER {fixed(1), external(2)}read-onlycurrent
enterpriseApRadioFixedAntennaType
OBJECT-TYPE
This value indicates which antenna type is in use as the fixed antenna is selected.
1.3.6.1.4.1.52.4.13.8.2.1.13INTEGER {diversity(1), left(2), right(3)}read-writecurrent
enterpriseApRadioAntennaID
OBJECT-TYPE
This value indicates which antenna ID will be in use for the radio Interface.
1.3.6.1.4.1.52.4.13.8.2.1.14INTEGERread-writecurrent
enterpriseApRadioMulticastDataRate
OBJECT-TYPE
This value indicates the data rate for mc/bc packets from this radio interface. sixMbps(6), nineMbps(9), twelveMbps(12), eighteenMbps(18), twentyFourMbps(24), thirtySixMbps(36), fortyEightMbps(48), and fiftyFourMbps(54) are for 11a and g-only mode. The default for b-only and b+g mode is oneMbps(1), twoMbps(2), fiveAndHalfMbps(5) and elevenMbps(11).
1.3.6.1.4.1.52.4.13.8.2.1.15INTEGER {oneMbps(1), twoMbps(2), fiveAndHalfMbps(5), sixMbps(6), nineMbps(9), elevenMbps(11), twelveMbps(12), eighteenMbps(18), twentyFourMbps(24), thirtySixMbps(36), fortyEightMbps(48), fiftyFourMbps(54)}read-writecurrent
enterpriseApRadioAutoDataRate
OBJECT-TYPE
This value indicates whether automated data rate is enabled or not for this radio interface
1.3.6.1.4.1.52.4.13.8.2.1.16INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApRadioPreamble
OBJECT-TYPE
This value indicates the preamble length of 11g. The values are interpreted as follows: long(1) sets the preamble length to long. short(2) sets the preamble length to short. invalid(3) means not support. This setting is only valid for the 802.11g interface.
1.3.6.1.4.1.52.4.13.8.2.1.17INTEGER {long(1), short(2), invalid(3)}read-writecurrent
enterpriseApRadioSWRetryMode
OBJECT-TYPE
This value indicates whether SW retty mode is enabled or not for this radio interface
1.3.6.1.4.1.52.4.13.8.2.1.18INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApVapRadioTable
OBJECT-TYPE
Table of descriptive and status information about configuration of each Vap radio.
1.3.6.1.4.1.52.4.13.8.3not-accessiblecurrent
enterpriseApVapRadioEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of one Vap radio of the AP.
1.3.6.1.4.1.52.4.13.8.3.1not-accessiblecurrent
enterpriseApVapRadioIndex
OBJECT-TYPE
Radio Index for configuration.
1.3.6.1.4.1.52.4.13.8.3.1.1Integer32 (1..2147483647)not-accessiblecurrent
enterpriseApVapRadioState
OBJECT-TYPE
This value indicates the state of the radio interface.
1.3.6.1.4.1.52.4.13.8.3.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApVapRadioSecureAccess
OBJECT-TYPE
This value indicates whether secure access is enabled for this radio interface.
1.3.6.1.4.1.52.4.13.8.3.1.3INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApVapRadioMaxAssoc
OBJECT-TYPE
This value indicates the max number of clients allowed on this radio interface.
1.3.6.1.4.1.52.4.13.8.3.1.4INTEGER (0..255)read-writecurrent
enterpriseApVapRadioTransmitKey
OBJECT-TYPE
This value indicates default transmit key in use for this radio interface.
1.3.6.1.4.1.52.4.13.8.3.1.5INTEGER (1..4)read-writecurrent
enterpriseApVapRadioDescription
OBJECT-TYPE
This value indicates the description for this radio interface.
1.3.6.1.4.1.52.4.13.8.3.1.6DisplayString (SIZE(0..80))read-writecurrent
enterpriseApVapRadioDefefaultPriority
OBJECT-TYPE
This values indicates the level of default priority of that specified VAP in entry.
1.3.6.1.4.1.52.4.13.8.3.1.7Integer32 (0..7)read-writecurrent
enterpriseApRadioWdsTable
OBJECT-TYPE
Table of configuration information for Wds for each Radio interface.
1.3.6.1.4.1.52.4.13.8.4not-accessiblecurrent
enterpriseApRadioWdsEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding to enterpriseApRadioTable). The table does not contain the radio index as a member of the table.
1.3.6.1.4.1.52.4.13.8.4.1not-accessiblecurrent
wdsApRole
OBJECT-TYPE
This value indicates the role of the Ap for this radio, roleAp(1): AP operation. roleBridgeMaster(2): Root-Bridge mode. roleBridge(3): Bridge Mode.
1.3.6.1.4.1.52.4.13.8.4.1.1INTEGER {roleAp(1), roleBridgeMaster(2), roleBridge(3)}read-writecurrent
wdsApAckTimeout
OBJECT-TYPE
This value indicates the WDS Ack timeout for this radio in us, and the following values can be set to the system: 0 Set wireless Ack Timeout as system default 20 0 to 1 miles: Ack timeout is 20 us 40 1 to 3 miles: Ack timeout is 40 us 75 3 to 6 miles: Ack timeout is 75 us 115 6 to 10 miles: Ack timeout is 115 us
1.3.6.1.4.1.52.4.13.8.4.1.2INTEGERread-writecurrent
enterpriseApRadioWdsPeerTable
OBJECT-TYPE
Table of configuration information for Wds Peers for each Radio interface.
1.3.6.1.4.1.52.4.13.8.5not-accessiblecurrent
enterpriseApRadioWdsPeerEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of peer Bridging for one radio of the AP. The table is indexed by radio Index (corresponding to enterpriseApRadioTable) and the peer index (Up to 8). The table does not contain the radio index as a member of the table.
1.3.6.1.4.1.52.4.13.8.5.1not-accessiblecurrent
wdsPeerIndex
OBJECT-TYPE
Peer Index for the radio interface.
1.3.6.1.4.1.52.4.13.8.5.1.1Integer32 (1..8)not-accessiblecurrent
wdsPeerBssid
OBJECT-TYPE
The BSSID for this peer.
1.3.6.1.4.1.52.4.13.8.5.1.2DisplayString (SIZE(1..17))read-writecurrent
wdsPeerRSSI
OBJECT-TYPE
This value indicates the RSSI value of the WDS peer link.
1.3.6.1.4.1.52.4.13.8.5.1.3Integer32read-onlycurrent
enterpriseApRadioWEPKeysTable
OBJECT-TYPE
Conceptual table for WEP default keys.
1.3.6.1.4.1.52.4.13.8.6not-accessiblecurrent
enterpriseApRadioWEPKeysEntry
OBJECT-TYPE
An Entry (conceptual row) in the WEP Default Keys Table. A collection of objects containing information used to determine if a WEPkey as been defined and if so, the value of the WEPkey.
1.3.6.1.4.1.52.4.13.8.6.1not-accessiblecurrent
enterpriseApRadioWEPKeysIndex
OBJECT-TYPE
WEP Key Index for the radio interface.
1.3.6.1.4.1.52.4.13.8.6.1.1INTEGER (1..4)not-accessiblecurrent
enterpriseApRadioWEPKeyType
OBJECT-TYPE
status of the WEP Key type
1.3.6.1.4.1.52.4.13.8.6.1.2INTEGER {hexadecimalKey(1), alphanumericKey(2), otherKey(3)}read-onlycurrent
enterpriseApRadioWEPKeyLength
OBJECT-TYPE
status of the WEP Key Length.
1.3.6.1.4.1.52.4.13.8.6.1.3INTEGER {keyLength64Bit(1), keyLength128Bit(2), keyLength152Bit(3), keyLengthOther(4)}read-onlycurrent
enterpriseApRadioAvAntennaListTable
OBJECT-TYPE
Conceptual table for Available Antenna List used in the Radio.
1.3.6.1.4.1.52.4.13.8.7not-accessiblecurrent
enterpriseApRadioAvAntennaListEntry
OBJECT-TYPE
An Entry (conceptual row) in the Antenna List Table. A collection of objects containing information used to show if an Antenna as been defined and if so, the value of the antenna Id.
1.3.6.1.4.1.52.4.13.8.7.1not-accessiblecurrent
enterpriseApRadioAvAntennaIndex
OBJECT-TYPE
Available Antenna List Index for the radio interface.
1.3.6.1.4.1.52.4.13.8.7.1.1INTEGER (1..65535)not-accessiblecurrent
enterpriseApRadioAvAntennaId
OBJECT-TYPE
Available antenna Id in the entry.
1.3.6.1.4.1.52.4.13.8.7.1.2INTEGERread-onlycurrent
enterpriseApRadioAvAntennaDesc
OBJECT-TYPE
The description of the antenna ID.
1.3.6.1.4.1.52.4.13.8.7.1.3DisplayString (SIZE(0..80))read-onlycurrent
enterpriseApRadioAvChannelListTable
OBJECT-TYPE
Conceptual table for Available Channel List used in the Radio.
1.3.6.1.4.1.52.4.13.8.8not-accessiblecurrent
enterpriseApRadioAvChannelListEntry
OBJECT-TYPE
An Entry (conceptual row) in the Channel List Table. A collection of objects containing information used to show if a Channel No. as been defined and if so, the value of the Channel No.
1.3.6.1.4.1.52.4.13.8.8.1not-accessiblecurrent
enterpriseApRadioAvChannelIndex
OBJECT-TYPE
Channel List Index for the radio interface.
1.3.6.1.4.1.52.4.13.8.8.1.1INTEGER (1..65535)not-accessiblecurrent
enterpriseApRadioAvChannelNo
OBJECT-TYPE
Available channel number in the entry
1.3.6.1.4.1.52.4.13.8.8.1.2INTEGERread-onlycurrent
apEtherInterfaceMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.9
apEtherNetConfig
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.9.1
netConfigIPAddress
OBJECT-TYPE
The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
1.3.6.1.4.1.52.4.13.9.1.1IpAddressread-writecurrent
netConfigSubnetMask
OBJECT-TYPE
The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use DHCP to try to figure out what these values should be. If DHCP fails, before the device can talk on the network, this value must be configured (e.g., through a terminal attached to the device).
1.3.6.1.4.1.52.4.13.9.1.2IpAddressread-writecurrent
netConfigDefaultGateway
OBJECT-TYPE
The IP Address of the default gateway. If this value is undefined or unknown, it shall have the value 0.0.0.0.
1.3.6.1.4.1.52.4.13.9.1.3IpAddressread-writecurrent
netConfigHttpState
OBJECT-TYPE
Whether HTTP is enabled.
1.3.6.1.4.1.52.4.13.9.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
netConfigHttpPort
OBJECT-TYPE
The port number for HTTP.
1.3.6.1.4.1.52.4.13.9.1.5INTEGER (514..65535)read-writecurrent
netConfigHttpsState
OBJECT-TYPE
Whether Secure HTTP is enabled.
1.3.6.1.4.1.52.4.13.9.1.6INTEGER {enabled(1), disabled(2)}read-writecurrent
netConfigHttpsPort
OBJECT-TYPE
The port number for Secure HTTP.
1.3.6.1.4.1.52.4.13.9.1.7INTEGER (514..65535)read-writecurrent
netConfigDHCPState
OBJECT-TYPE
Whether DHCP is enabled.
1.3.6.1.4.1.52.4.13.9.1.8INTEGER {enabled(1), disabled(2)}read-writecurrent
apFilterControlMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.10
apFilterControlBridge
OBJECT-TYPE
This value indicates the local bridge filter setting.
1.3.6.1.4.1.52.4.13.10.1INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApFilterControlAPManage
OBJECT-TYPE
This value indicates the AP management filter setting.
1.3.6.1.4.1.52.4.13.10.2INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApFilterControlEthernet
OBJECT-TYPE
This value indicates the ethernet filter setting.
1.3.6.1.4.1.52.4.13.10.3INTEGER {enabled(1), disabled(2)}read-writecurrent
enterpriseApFilterProtocolTable
OBJECT-TYPE
Table of descriptive and status information about configuration of the filter protocol table.
1.3.6.1.4.1.52.4.13.10.4not-accessiblecurrent
enterpriseApFilterProtocolEntry
OBJECT-TYPE
An entry in the filter protocol table, containing information about configuration of one filter table entry.
1.3.6.1.4.1.52.4.13.10.4.1not-accessiblecurrent
enterpriseApFilterProtocolIndex
OBJECT-TYPE
Index of the Protocol Filters.
1.3.6.1.4.1.52.4.13.10.4.1.1Integer32 (1..2147483647)not-accessiblecurrent
enterpriseApFilterProtocolName
OBJECT-TYPE
This value indicates the name of the protocol filter. One of the following: Aironet_DDP, Appletalk_ARP, ARP, Banyan, Berkeley_Trailer_Negotiation, CDP, DEC_LAT, DEC_MOP, DEC_MOP_Dump_Load, DEC_XNS, EAPOL, Enet_Config_Test, Ethertalk, IP, LAN_Test, NetBEUI, Novell_IPX(new), Novell_IPX(old), RARP, Telxon_TXP, X.25_Level3
1.3.6.1.4.1.52.4.13.10.4.1.2DisplayStringread-onlycurrent
enterpriseApFilterProtocolISODesignator
OBJECT-TYPE
This value indicates the name of the protocol filter.
1.3.6.1.4.1.52.4.13.10.4.1.3DisplayStringread-onlycurrent
enterpriseApFilterProtocolState
OBJECT-TYPE
This value indicates whether the protocol filter is enabled.
1.3.6.1.4.1.52.4.13.10.4.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
apvGlobalIBSSRelayMode
OBJECT-TYPE
This value indicates the setting of the global IBSS Relay mode among the VAPs. In Per-VAP Mode enable, the traffic between the VAPs should be blocked. In Al-VAP Mode enable, the traffic between should not be blocked.
1.3.6.1.4.1.52.4.13.10.5INTEGER {perVapModeEnable(1), allVapModeEnable(2)}read-writecurrent
apvFilterControlTable
OBJECT-TYPE
Table of the control and status information about configuration of the filter Control for each Vap.
1.3.6.1.4.1.52.4.13.10.6not-accessiblecurrent
apvFilterControlEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of the filter for each Vap of the AP.
1.3.6.1.4.1.52.4.13.10.6.1not-accessiblecurrent
apvFilterControlIndex
OBJECT-TYPE
Index of the configuration.
1.3.6.1.4.1.52.4.13.10.6.1.1Integer32 (1..2147483647)not-accessiblecurrent
apvIBSSFilterControl
OBJECT-TYPE
This value indicates the local bridge filter(IBSS Relay Filter) setting.
1.3.6.1.4.1.52.4.13.10.6.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
apvAPManageFilterControl
OBJECT-TYPE
This value indicates the AP management filter setting.
1.3.6.1.4.1.52.4.13.10.6.1.3INTEGER {enabled(1), disabled(2)}read-writecurrent
apVLANMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.11
apVLANMgntNativeId
OBJECT-TYPE
This value indicates the native VLAN Id.
1.3.6.1.4.1.52.4.13.11.1INTEGERread-writecurrent
apVLANMgntState
OBJECT-TYPE
This value indicates whether VLANs are enabled or disabled.
1.3.6.1.4.1.52.4.13.11.2INTEGER {enabled(1), disabled(2)}read-onlycurrent
apVLANMgntStateNextBoot
OBJECT-TYPE
This value indicates the VLANs state for the next reset.
1.3.6.1.4.1.52.4.13.11.3INTEGER {enabled(1), disabled(2)}read-writecurrent
apNativeVlanTable
OBJECT-TYPE
Table used to manage the Vlans for each wireless interface.
1.3.6.1.4.1.52.4.13.11.6not-accessiblecurrent
apNativeVlanEntry
OBJECT-TYPE
An entry in the table, containing information about VLAN configuration of one wireless interface.
1.3.6.1.4.1.52.4.13.11.6.1not-accessiblecurrent
apNativeVlanIfIndex
OBJECT-TYPE
Interface Index of the wireless interface for which the VLAN is assigned to.
1.3.6.1.4.1.52.4.13.11.6.1.1Integer32 (1..2147483647)not-accessiblecurrent
apNativeVlanSsidNumber
OBJECT-TYPE
Associated Number for Service Set Id (SSID) of the wireless interface for which the VLAN is assigned to. Note: This is for future support of multiple SSIDs per radio interface.
1.3.6.1.4.1.52.4.13.11.6.1.2Integer32 (1..2147483647)not-accessiblecurrent
apNativeVlanVlanId
OBJECT-TYPE
This value indicates the native VLAN Id of the wireless interface associated with the if index and the SSID number(if it is not 0).
1.3.6.1.4.1.52.4.13.11.6.1.3Integer32read-writecurrent
apNativeVlanState
OBJECT-TYPE
This value indicates the Native VLANs state.
1.3.6.1.4.1.52.4.13.11.6.1.4INTEGER {enabled(1), disabled(2)}read-writecurrent
apVLANMgntEtherUntaggedVlanId
OBJECT-TYPE
This value indicates the Untagged VlanID for Ether Interface.
1.3.6.1.4.1.52.4.13.11.7Integer32read-writecurrent
apAuthenticationMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.12
apAuthenticationSetupEntry
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.12.1
ap8021xState
OBJECT-TYPE
This attribute indicates that the Enterprise the state of the 802.1X authentication algorithm.
1.3.6.1.4.1.52.4.13.12.1.1INTEGER {disabled(0), supported(1), required(2)}read-writecurrent
ap8021xBroadcastKeyRefreshRate
OBJECT-TYPE
The number (in minutes) between changing the broadcast key for 802.1X and WPA clients
1.3.6.1.4.1.52.4.13.12.1.2INTEGER (0..1440)read-writecurrent
ap8021xSessionKeyRefreshRate
OBJECT-TYPE
The number (in minutes) between changing session keys for 802.1X and WPA clients
1.3.6.1.4.1.52.4.13.12.1.3INTEGER (0..1440)read-writecurrent
ap8021xReauthenticationTimeout
OBJECT-TYPE
The number (in minutes) between forcing 802.1X clients to reauthenticate
1.3.6.1.4.1.52.4.13.12.1.4INTEGER (0..1440)read-writecurrent
apAuthenticationMode
OBJECT-TYPE
This value indicates the type of MAC authentication or RADIUS authentication in use, or not in use.
1.3.6.1.4.1.52.4.13.12.1.5INTEGER {disabled(0), local(1), radius(2)}read-writecurrent
apAuthenticationServerTable
OBJECT-TYPE
Table of descriptive and status information about configuration of each authentication server.
1.3.6.1.4.1.52.4.13.12.2not-accessiblecurrent
apAuthenticationServerEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of one authentication server of the AP.
1.3.6.1.4.1.52.4.13.12.2.1not-accessiblecurrent
apAuthenticationServerIndex
OBJECT-TYPE
Index of the Authentication Server
1.3.6.1.4.1.52.4.13.12.2.1.1Integer32 (1..2147483647)not-accessiblecurrent
apAuthenticationServer
OBJECT-TYPE
This value indicates the IP address or host name of the authentication server.
1.3.6.1.4.1.52.4.13.12.2.1.2DisplayString (SIZE(1..64))read-writecurrent
apAuthenticationPort
OBJECT-TYPE
This value indicates the UDP Port used by the authentication server.
1.3.6.1.4.1.52.4.13.12.2.1.3INTEGER (1024..65535)read-writecurrent
apAuthenticationKey
OBJECT-TYPE
This value indicates the shared key used by the authentication server.
1.3.6.1.4.1.52.4.13.12.2.1.4DisplayString (SIZE(0..64))read-writecurrent
apAuthenticationRetransmit
OBJECT-TYPE
This value indicates the retransmit timer length used by the authentication server.
1.3.6.1.4.1.52.4.13.12.2.1.5INTEGER (1..30)read-writecurrent
apAuthenticationTimeout
OBJECT-TYPE
This value indicates the Timeout value(sec) used by the authentication server.
1.3.6.1.4.1.52.4.13.12.2.1.6INTEGER (1..60)read-writecurrent
apAuthenticationAcctPort
OBJECT-TYPE
UDP Accounting Port. The valid range is from 1024-65535. A value of 0 means accounting is disabled.
1.3.6.1.4.1.52.4.13.12.2.1.7INTEGER (0..65535)read-writecurrent
apAuthenticationAcctInterimUpdate
OBJECT-TYPE
The interval between sending accounting updates.
1.3.6.1.4.1.52.4.13.12.2.1.8INTEGER (60..86400)read-writecurrent
apAuthenticationAcctState
OBJECT-TYPE
This value indicates whether the Accounting Server is enabled.
1.3.6.1.4.1.52.4.13.12.2.1.9INTEGER {enabled(1), disabled(2)}read-writecurrent
apAuthenticationSupplicantTable
OBJECT-TYPE
Table of descriptive and status information about configuration of supplicant
1.3.6.1.4.1.52.4.13.12.3not-accessiblecurrent
apAuthenticationSupplicantEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of one supplicant.
1.3.6.1.4.1.52.4.13.12.3.1not-accessiblecurrent
ap8021xSuppIndex
OBJECT-TYPE
Index of the interface for which this supplicant is running. Currently only the ethernet interface.
1.3.6.1.4.1.52.4.13.12.3.1.1Integer32 (1..2147483647)not-accessiblecurrent
ap8021xSuppState
OBJECT-TYPE
This object is used to enable or disable the 802.1X supplicant.
1.3.6.1.4.1.52.4.13.12.3.1.2INTEGER {disabled(0), enabled(1)}read-writecurrent
ap8021xSuppUser
OBJECT-TYPE
This value indicates the username for supplicant. If value is configured, will display ****. Else will display EMPTY.
1.3.6.1.4.1.52.4.13.12.3.1.3DisplayString (SIZE(1..32))read-writecurrent
ap8021xSuppPasswd
OBJECT-TYPE
This value indicates the password for supplicant. If value is configured, will display ****. Else will display EMPTY.
1.3.6.1.4.1.52.4.13.12.3.1.4DisplayString (SIZE(1..32))read-writecurrent
apvAuthenticationSetupTable
OBJECT-TYPE
Table of descriptive and status information about configuration of 8021x for each Vap.
1.3.6.1.4.1.52.4.13.12.4not-accessiblecurrent
apvAuthenticationSetupEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of 8021x for each Vap of the AP.
1.3.6.1.4.1.52.4.13.12.4.1not-accessiblecurrent
apv8021xIndex
OBJECT-TYPE
Index for configuration.
1.3.6.1.4.1.52.4.13.12.4.1.1Integer32 (1..2147483647)not-accessiblecurrent
apv8021xState
OBJECT-TYPE
This attribute indicates that the Enterprise the state of the 802.1X authentication algorithm.
1.3.6.1.4.1.52.4.13.12.4.1.2INTEGER {disabled(0), supported(1), required(2)}read-writecurrent
apv8021xBroadcastKeyRefreshRate
OBJECT-TYPE
The number (in minutes) between changing the broadcast key for 802.1X and WPA clients
1.3.6.1.4.1.52.4.13.12.4.1.3INTEGER (0..1440)read-writecurrent
apv8021xSessionKeyRefreshRate
OBJECT-TYPE
The number (in minutes) between changing history keys for 802.1X and WPA clients
1.3.6.1.4.1.52.4.13.12.4.1.4INTEGER (0..1440)read-writecurrent
apv8021xReauthenticationTimeout
OBJECT-TYPE
The number (in minutes) between forcing 802.1X clients to reauthenticate
1.3.6.1.4.1.52.4.13.12.4.1.5INTEGER (0..65535)read-writecurrent
apvMACAuthenticationMode
OBJECT-TYPE
This value indicates the mode of MAC authentication in use.
1.3.6.1.4.1.52.4.13.12.4.1.6INTEGER {disabled(0), local(1), remote(2)}read-writecurrent
apvMACAuthenticationTimeout
OBJECT-TYPE
The number (in minutes) between forcing RADIUS MAC to authenticate.
1.3.6.1.4.1.52.4.13.12.4.1.7INTEGER (0..65535)read-writecurrent
apvMACAuthenticationPasswd
OBJECT-TYPE
This value indicates the password for MAC RADIUS Authentication. If value is configured, will display ****. Else will display EMPTY.
1.3.6.1.4.1.52.4.13.12.4.1.8DisplayString (SIZE(1..31))read-writecurrent
apWStationSessionMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.13
apWStationSessionTable
OBJECT-TYPE
This table list all sessions (wireless stations) status
1.3.6.1.4.1.52.4.13.13.1not-accessiblecurrent
apWStationSessionEntry
OBJECT-TYPE
An entry in the table, containing information about status and statistics of the wireless station.
1.3.6.1.4.1.52.4.13.13.1.1not-accessiblecurrent
apWStationSessionIfIndex
OBJECT-TYPE
Interface index for the radio this session is associated with.
1.3.6.1.4.1.52.4.13.13.1.1.1Integer32 (1..2147483647)not-accessiblecurrent
apWStationSessionStationAddres
OBJECT-TYPE
The unique MAC Address of the station for this session.
1.3.6.1.4.1.52.4.13.13.1.1.2MacAddressnot-accessiblecurrent
apWStationSessionAuthenticated
OBJECT-TYPE
Whether the session is authenticated or not.
1.3.6.1.4.1.52.4.13.13.1.1.3TruthValueread-onlycurrent
apWStationSessionAssociated
OBJECT-TYPE
Whether the session is associated or not. It is rare case that not associated stations show up in the table.
1.3.6.1.4.1.52.4.13.13.1.1.4TruthValueread-onlycurrent
apWStationSessionIsForwarding
OBJECT-TYPE
Whether the AP is forwarding the client station traffic (higher level authentication)
1.3.6.1.4.1.52.4.13.13.1.1.5TruthValueread-onlycurrent
apWStationSessionKeyType
OBJECT-TYPE
The encryption key type used by the station. Note that wpa-wep is not supported
1.3.6.1.4.1.52.4.13.13.1.1.6INTEGER {none(1), staticWep(2), dynamicWep(3), wpaWep(4), wpaTkip(5), wpaAes(6)}read-onlycurrent
apWStationSessionAssociationId
OBJECT-TYPE
The internal association identify number
1.3.6.1.4.1.52.4.13.13.1.1.7Integer32read-onlycurrent
apWStationSessionLastAuthenticatedTime
OBJECT-TYPE
This is the time in hundredths of a second last time the client is authenticated. Note that a session may be authenticated multiple times. The value is related to the system startup
1.3.6.1.4.1.52.4.13.13.1.1.8TimeTicksread-onlycurrent
apWStationSessionAssociatedTime
OBJECT-TYPE
This is the time in hundredths of a second since the client associated. The value is related to the system startup
1.3.6.1.4.1.52.4.13.13.1.1.9TimeTicksread-onlycurrent
apWStationSessionLastAssociatedTime
OBJECT-TYPE
This is the time in hundredths of a second when the client associated in last session. The value is related to the system startup
1.3.6.1.4.1.52.4.13.13.1.1.10TimeTicksread-onlycurrent
apWStationSessionLastDisassociatedTime
OBJECT-TYPE
This is the time in hundredths of a second when the client disassociated in last session. The value is related to the system startup
1.3.6.1.4.1.52.4.13.13.1.1.11TimeTicksread-onlycurrent
apWStationSessionTxPacketCount
OBJECT-TYPE
This is the number of packets transmitted from the client to the AP. It includes data, control and management packets.
1.3.6.1.4.1.52.4.13.13.1.1.12Counter32read-onlycurrent
apWStationSessionRxPacketCount
OBJECT-TYPE
This is the number of unicast packets transmitted from the AP to the client. It includes data, control and management packets.
1.3.6.1.4.1.52.4.13.13.1.1.13Counter32read-onlycurrent
apWStationSessionTxByteCount
OBJECT-TYPE
This is the number of bytes transmitted from the client to the AP. It includes the bytes of data, control and management packets.
1.3.6.1.4.1.52.4.13.13.1.1.14Counter32read-onlycurrent
apWStationSessionRxByteCount
OBJECT-TYPE
This is the number of unicast bytes transmitted from the AP to the client. It includes the bytes of data, control and management packets.
1.3.6.1.4.1.52.4.13.13.1.1.15Counter32read-onlycurrent
apWStationSessionVlanID
OBJECT-TYPE
The current VLAN Id used by the station.
1.3.6.1.4.1.52.4.13.13.1.1.16INTEGERread-onlycurrent
apRogueApMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.14
rogueApDetectionTable
OBJECT-TYPE
Table of each AP that has been detected.
1.3.6.1.4.1.52.4.13.14.1not-accessiblecurrent
rogueApDetectionEntry
OBJECT-TYPE
An entry in the table, containing information about any AP detected.
1.3.6.1.4.1.52.4.13.14.1.1not-accessiblecurrent
rogueApIndex
OBJECT-TYPE
Monotonically increasing index.
1.3.6.1.4.1.52.4.13.14.1.1.1INTEGER (1..128)not-accessiblecurrent
rogueApBssid
OBJECT-TYPE
The AP BSSID
1.3.6.1.4.1.52.4.13.14.1.1.2DisplayString (SIZE(0..6))read-onlycurrent
rogueApSsid
OBJECT-TYPE
The AP SSID
1.3.6.1.4.1.52.4.13.14.1.1.3DisplayString (SIZE(0..40))read-onlycurrent
rogueApPortNumber
OBJECT-TYPE
Interface index for the radio.
1.3.6.1.4.1.52.4.13.14.1.1.4Integer32read-onlycurrent
rogueApChannelNumber
OBJECT-TYPE
Channel where Ap detected.
1.3.6.1.4.1.52.4.13.14.1.1.5Integer32read-onlycurrent
rogueApRSSIValue
OBJECT-TYPE
RSSI for AP detected.
1.3.6.1.4.1.52.4.13.14.1.1.6Integer32read-onlycurrent
apRougeApControl
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.14.2
rogueApRADIUSAuthenticate
OBJECT-TYPE
Value is used to enable/disable RADIUS Authentication.
1.3.6.1.4.1.52.4.13.14.2.1INTEGER {enabled(1), disabled(2)}read-writecurrent
rogueApClear
OBJECT-TYPE
This object is set to clear(1) to clear the Rogue AP detection table. When read, the value will have no meaning.
1.3.6.1.4.1.52.4.13.14.2.2INTEGER {clear(1)}read-writecurrent
apAdminMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.15
apAdminUsername
OBJECT-TYPE
This value indicates the username for management login.
1.3.6.1.4.1.52.4.13.15.1DisplayString (SIZE(0..16))read-writecurrent
appAdminPassword
OBJECT-TYPE
This value indicates the password for management login.
1.3.6.1.4.1.52.4.13.15.2DisplayString (SIZE(0..16))read-writecurrent
apResetMgt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.16
apRestartOpCodeFile
OBJECT-TYPE
Name of op-code file for start-up.
1.3.6.1.4.1.52.4.13.16.1DisplayString (SIZE(0..127))read-writecurrent
apRestartControl
OBJECT-TYPE
Setting this object to warmBoot(2) causes the device to restart the application software with current configuration parameters saved in non-volatile memory. Setting this object to coldBoot(3) causes the device to reinitialize configuration parameters in non-volatile memory to default values and restart the application software. When the device is running normally, this variable has a value of running(1).
1.3.6.1.4.1.52.4.13.16.2INTEGER {running(1), warmBoot(2), coldBoot(3)}read-writecurrent
apSNTPMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.17
apSNTPState
OBJECT-TYPE
This value indicates whether SNTP is enabled or not. At least one of the SNTP servers must have a valid IP address before SNTP can be enabled.
1.3.6.1.4.1.52.4.13.17.1INTEGER {enabled(1), disabled(2)}read-writecurrent
apSNTPPrimaryServer
OBJECT-TYPE
This value indicates the IP address of the primary SNTP server.
1.3.6.1.4.1.52.4.13.17.2IpAddressread-writecurrent
apSNTPSecondaryServer
OBJECT-TYPE
This value indicates the IP address of the secondary SNTP server.
1.3.6.1.4.1.52.4.13.17.3IpAddressread-writecurrent
apSNTPTimezone
OBJECT-TYPE
This value indicates which timezone to use.
1.3.6.1.4.1.52.4.13.17.4INTEGER {enewetakKwajalein(0), midwayIsland(1), hawaii(2), alaska(3), pacific(4), arizona(5), mountain(6), central(7), mexicoCity(8), saskatchewan(9), bogota(10), eastern(11), indiana(12), atlantic(13), caracas(14), santiago(15), newfoundland(16), brasilia(17), buenos(18), midAtlantic(19), azores(20), casablanca(21), greenwichMeanTimeDublin(22), greenwichMeanTimeLisbon(23), amsterdam(24), stockholm(25), bratislava(26), prague(27), paris(28), sofija(29), athens(30), bucharest(31), cairo(32), harare(33), helsinki(34), israel(35), baghdad(36), moscow(37), tehran(38), abuDhabi(39), vogograd(40), islamabad(41), almaty(42), bangkok(43), beijing(44), taipei(45), tokyo(46), brisbane(47), canberra(48), guam(49), hobart(50), magadan(51), fiji(52), wellington(53)}read-writecurrent
apSNTPDST
OBJECT-TYPE
This value indicates whether Daylight Savings Time is enabled or not.
1.3.6.1.4.1.52.4.13.17.5INTEGER {enabled(1), disabled(2)}read-writecurrent
apSNTPDSTStartMonth
OBJECT-TYPE
This value indicates the starting month for Daylight Savings Time.
1.3.6.1.4.1.52.4.13.17.6INTEGER (1..12)read-writecurrent
apSNTPDSTStartDay
OBJECT-TYPE
This value indicates the starting day for Daylight Savings Time.
1.3.6.1.4.1.52.4.13.17.7INTEGER (1..31)read-writecurrent
apSNTPDSTEndMonth
OBJECT-TYPE
This value indicates the ending month for Daylight Savings Time.
1.3.6.1.4.1.52.4.13.17.8INTEGER (1..12)read-writecurrent
apSNTPDSTEndDay
OBJECT-TYPE
This value indicates the ending day for Daylight Savings Time.
1.3.6.1.4.1.52.4.13.17.9INTEGER (1..31)read-writecurrent
apDNSMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.18
apDNSPrimaryServer
OBJECT-TYPE
This value indicates the IP address of the primary DNS server.
1.3.6.1.4.1.52.4.13.18.1IpAddressread-writecurrent
apDNSSecondaryServer
OBJECT-TYPE
This value indicates the IP address of the secondary DNS server.
1.3.6.1.4.1.52.4.13.18.2IpAddressread-writecurrent
apIappMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.19
apIappEnabled
OBJECT-TYPE
Whether IAPP is enabled.
1.3.6.1.4.1.52.4.13.19.1INTEGER {enabled(1), disabled(2)}read-writecurrent
apSyslogConfigMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.20
apLogConfigState
OBJECT-TYPE
This value indicates whether syslog is enabled.
1.3.6.1.4.1.52.4.13.20.1INTEGER {enabled(1), disabled(2)}read-writecurrent
apSyslogConsoleState
OBJECT-TYPE
This value indicates whether syslog console logging is enabled.
1.3.6.1.4.1.52.4.13.20.2INTEGER {enabled(1), disabled(2)}read-writecurrent
apSyslogLevel
OBJECT-TYPE
This value indicates the syslog logging level.
1.3.6.1.4.1.52.4.13.20.3INTEGER {emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), info(6), debug(7)}read-writecurrent
apSyslogServerTable
OBJECT-TYPE
Table of descriptive and status information about configuration of each syslog server.
1.3.6.1.4.1.52.4.13.20.4not-accessiblecurrent
apSyslogServerEntry
OBJECT-TYPE
An entry in the table, containing information about configuration of one syslog server of the AP.
1.3.6.1.4.1.52.4.13.20.4.1not-accessiblecurrent
apSyslogServerIndex
OBJECT-TYPE
Index of the Syslog Server
1.3.6.1.4.1.52.4.13.20.4.1.1Integer32 (1..4)not-accessiblecurrent
apSyslogServerState
OBJECT-TYPE
This value indicates whether the syslog server is enabled.
1.3.6.1.4.1.52.4.13.20.4.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
apSyslogServerIPAddress
OBJECT-TYPE
This value indicates the IP address of the syslog server.
1.3.6.1.4.1.52.4.13.20.4.1.3DisplayString (SIZE(1..32))read-writecurrent
apSyslogServerPort
OBJECT-TYPE
This value indicates the UDP Port used by the syslog server.
1.3.6.1.4.1.52.4.13.20.4.1.4INTEGER (1024..65535)read-writecurrent
apEventLogMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.21
apEventLogTable
OBJECT-TYPE
This table is a snapshot of the current event log.
1.3.6.1.4.1.52.4.13.21.1not-accessiblecurrent
apEventLogEntry
OBJECT-TYPE
An entry in the table, containing one message from the event log.
1.3.6.1.4.1.52.4.13.21.1.1not-accessiblecurrent
apEventLogIndex
OBJECT-TYPE
Index of the Event Log Message
1.3.6.1.4.1.52.4.13.21.1.1.1INTEGER (1..128)not-accessiblecurrent
apEventLogMessage
OBJECT-TYPE
The Event Log Message
1.3.6.1.4.1.52.4.13.21.1.1.2DisplayString (SIZE(0..256))read-onlycurrent
apEventLogClear
OBJECT-TYPE
This object is set to 1 to clear the event log. When read, the value will have no meaning.
1.3.6.1.4.1.52.4.13.21.2INTEGER {clearLog(1)}read-writecurrent
apWSLSupportMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.22
apWSLSupportControl
OBJECT-TYPE
The administrative enable/disable state for the control of the WSL function.
1.3.6.1.4.1.52.4.13.22.1INTEGER {enabled(1), disabled(2)}read-writecurrent
apWSLSupportMasterAddress
OBJECT-TYPE
This value indicates IP address of the main WSL.
1.3.6.1.4.1.52.4.13.22.2DisplayString (SIZE(1..32))read-writecurrent
apWSLSupportSecondaryAddress
OBJECT-TYPE
This value indicates IP address of the peer WSL.
1.3.6.1.4.1.52.4.13.22.3DisplayString (SIZE(1..32))read-writecurrent
apWSLSupportPort
OBJECT-TYPE
This value indicates the TCP Port used by the WSL server.
1.3.6.1.4.1.52.4.13.22.4INTEGER (1024..65535)read-writecurrent
apWSLSupportHeartbeatInterval
OBJECT-TYPE
This value indicates the WSL Heartbeat Interval.
1.3.6.1.4.1.52.4.13.22.5INTEGER (1..65535)read-writecurrent
apWSLSupportHeartbeatLastChange
OBJECT-TYPE
The sysUpTime at which the Heartbeat was last modified. The format is defined as hh:mm:ss - dd:mm:yy
1.3.6.1.4.1.52.4.13.22.6DisplayString (SIZE(1..20))read-onlycurrent
apWSLSupportOperationMode
OBJECT-TYPE
This attribute indicates that the WSL Operation Mode in 0: AP in standalone mode, or 1: AP in ETS WSL managed mode (associated mode).
1.3.6.1.4.1.52.4.13.22.7INTEGER {standalone(0), associated(1)}read-writecurrent
apWSLSupportRxThreshold
OBJECT-TYPE
This value indicates the WSL CCA rejection threshold in dBm scale.
1.3.6.1.4.1.52.4.13.22.8INTEGER (-128..127)read-writecurrent
apWSLSupportControlStatus
OBJECT-TYPE
The operative enable/disable state for the control of the WSL function.
1.3.6.1.4.1.52.4.13.22.9INTEGER {enabled(1), disabled(2)}read-onlycurrent
apWSLRFAreaPollControl
OBJECT-TYPE
The administrative enable/disable state for the control of the WSL RF Area Poll function.
1.3.6.1.4.1.52.4.13.22.10INTEGER {enabled(1), disabled(2)}read-onlycurrent
apWSLRFAreaPollControlStatus
OBJECT-TYPE
The operative enable/disable state for the control of the WSL RF Area Poll function.
1.3.6.1.4.1.52.4.13.22.11INTEGER {enabled(1), disabled(2)}read-onlycurrent
apWMMMgnt
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.23
apWMMControlTable
OBJECT-TYPE
Table for WMM configuration per radio.
1.3.6.1.4.1.52.4.13.23.1not-accessiblecurrent
apWMMControlEntry
OBJECT-TYPE
An Entry in the apWMMControlTable.
1.3.6.1.4.1.52.4.13.23.1.1not-accessiblecurrent
apWMMState
OBJECT-TYPE
This value indicates the WMM state.
1.3.6.1.4.1.52.4.13.23.1.1.1INTEGER {disabled(0), required(1), supported(2)}read-writecurrent
apWMMBssParamTable
OBJECT-TYPE
Conceptual table for EDCA default parameter values at a non-AP QSTA. This table shall contain the four entries of the EDCA parameters corresponding to four possible ACs (access category): 1) AC_BE (best effort, ACI=0) 2) AC_BK (background, ACI=1) 3) AC_VI (video, ACI=2) 4) AC_VO (voice, ACI=3)
1.3.6.1.4.1.52.4.13.23.2not-accessiblecurrent
apWMMBssParamEntry
OBJECT-TYPE
An Entry (conceptual row) in the apWMMBssParamTable. ifIndex - Each IEEE 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are indexed by ifIndex.
1.3.6.1.4.1.52.4.13.23.2.1not-accessiblecurrent
apWMMBssParamIndex
OBJECT-TYPE
The index used to identify instances of the columnar objects in the apWMMBssParam Table. The value of this variable is 1) 1 AC_BE (best effort, ACI=0) 2) 2 AC_BK (background, ACI=1) 3) 3 AC_VI (video, ACI=2) 4) 4 AC_VO (voice, ACI=3)
1.3.6.1.4.1.52.4.13.23.2.1.1INTEGER (1..4)not-accessiblecurrent
apWMMBssParamCWmin
OBJECT-TYPE
This attribute shall specify the value of the minimum size of the window in the exponent form that shall be used by a QSTA for a particular AC for generating a random number for the backoff.
1.3.6.1.4.1.52.4.13.23.2.1.2INTEGER (1..15)read-writecurrent
apWMMBssParamCWmax
OBJECT-TYPE
This attribute shall specify the value of the maximum size of the window in the exponent form that shall be used by a QSTA for a particular AC for generating a random number for the backoff.
1.3.6.1.4.1.52.4.13.23.2.1.3INTEGER (1..15)read-writecurrent
apWMMBssParamAIFSN
OBJECT-TYPE
This attribute shall specify the number of slots, after a SIFS duration, that the QSTA, for a particular AC, shall sense the medium idle either before transmitting or executing a backoff.
1.3.6.1.4.1.52.4.13.23.2.1.4INTEGER (1..15)read-writecurrent
apWMMBssParamTXOPLimit
OBJECT-TYPE
This attribute shall specify the maximum time of an TXOP in units of 32 microseconds for a given AC at a non-AP QSTA.
1.3.6.1.4.1.52.4.13.23.2.1.5INTEGER (0..65535)read-writecurrent
apWMMBssParamAdmissionControl
OBJECT-TYPE
This attribute, when TRUE, indicates that admission control is mandatory for the given AC. When False, this attribute indicates that the admission control is not mandatory for the given AC. The default value for this parameter shall be FALSE.
1.3.6.1.4.1.52.4.13.23.2.1.6TruthValueread-writecurrent
apWMMApParamTable
OBJECT-TYPE
Conceptual table for EDCA default parameter values at the QAP. This table shall contain the four entries of the EDCA parameters corresponding to four possible ACs (access category): 1) AC_BE (best effort, ACI=0) 2) AC_BK (background, ACI=1) 3) AC_VI (video, ACI=2) 4) AC_VO (voice, ACI=3)
1.3.6.1.4.1.52.4.13.23.3not-accessiblecurrent
apWMMApParamEntry
OBJECT-TYPE
An Entry (conceptual row) in the apWMMApParamTable. ifIndex - Each IEEE 802.11 interface is represented by an ifEntry. Interface tables in this MIB module are indexed by ifIndex.
1.3.6.1.4.1.52.4.13.23.3.1not-accessiblecurrent
apWMMApParamIndex
OBJECT-TYPE
The index used to identify instances of the columnar objects in the apWMMApParam Table. The value of this variable is 1) 1 AC_BE (best effort, ACI=0) 2) 2 AC_BK (background, ACI=1) 3) 3 AC_VI (video, ACI=2) 4) 4 AC_VO (voice, ACI=3)
1.3.6.1.4.1.52.4.13.23.3.1.1INTEGER (1..4)not-accessiblecurrent
apWMMApParamCWmin
OBJECT-TYPE
This attribute shall specify the value of the minimum size of the window in the exponent form that shall be used by a QAP for a particular AC for generating a random number for the backoff.
1.3.6.1.4.1.52.4.13.23.3.1.2INTEGER (1..15)read-writecurrent
apWMMApParamCWmax
OBJECT-TYPE
This attribute shall specify the value of the maximum size of the window in the exponent form that shall be used by a QAP for a particular AC for generating a random number for the backoff.
1.3.6.1.4.1.52.4.13.23.3.1.3INTEGER (1..15)read-writecurrent
apWMMApParamAIFSN
OBJECT-TYPE
This attribute shall specify the number of slots, after a SIFS duration, that the QAP, for a particular AC, shall sense the medium idle either before transmitting or executing a backoff.
1.3.6.1.4.1.52.4.13.23.3.1.4INTEGER (1..15)read-writecurrent
apWMMApParamTXOPLimit
OBJECT-TYPE
This attribute shall specify the maximum time of an TXOP in units of 32 microseconds for a given AC at a QAP.
1.3.6.1.4.1.52.4.13.23.3.1.5INTEGER (0..65535)read-writecurrent
apWMMApParamAdmissionControl
OBJECT-TYPE
This attribute, when TRUE, indicates that admission control is mandatory for the given AC. When False, this attribute indicates that the admission control is not mandatory for the given AC. The default value for this parameter shall be FALSE.
1.3.6.1.4.1.52.4.13.23.3.1.6TruthValueread-writecurrent
apNotificationTrapTree
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.100
apNotificationObjects
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.100.1
apNotificationDot11MacAddr
OBJECT-TYPE
Mac Address of the affected interface, returned with traps only.
1.3.6.1.4.1.52.4.13.100.1.1MacAddressread-onlycurrent
apNotificationDot11Station
OBJECT-TYPE
This attribute holds the MAC address of the wireless station
1.3.6.1.4.1.52.4.13.100.1.2MacAddressread-onlycurrent
apNotificationDot11RequestType
OBJECT-TYPE
This attribute defines the request type sent by the station. Value = 1: Unknown request type Value = 2: Association Request Value = 3: Re-association Request Value = 4: Authentication
1.3.6.1.4.1.52.4.13.100.1.3INTEGER {unknown(1), association(2), reAssociation(3), authentication(4)}read-onlycurrent
apNotificationDot11ReasonCode
OBJECT-TYPE
This attribute defines the reason for the failure of an operation. Value = 1: Invalid mode/state Value = 2: Station not authenticated. Value = 3: Internal error Value = 4: Out of sequence frame Value = 5: Un-supported algorithm Value = 6: Invalid frame length Value = 7: WEP is required on the AP Value = 8: WEP not allowed Value = 9: Challenge text mismatch
1.3.6.1.4.1.52.4.13.100.1.4INTEGER {invalidModeOrState(1), unAuthenticatedStation(2), internalError(3), outOfSequenceFrame(4), unsupportedAlgorithm(5), invalidFrameLngth(6), wepRequiredOnAP(7), wepNotAllowed(8), challengeTextMismatch(9)}read-onlycurrent
apNotificationDot11IpAddress
OBJECT-TYPE
This value indicates the IP address of the Access Point
1.3.6.1.4.1.52.4.13.100.1.5IpAddressread-onlycurrent
apNotificationDot11AuthenticatorMacAddr
OBJECT-TYPE
This attribute holds the MAC address of the authenticator for the AP.
1.3.6.1.4.1.52.4.13.100.1.6MacAddressread-onlycurrent
apNotificationTrapObjects
OBJECT-IDENTITY
1.3.6.1.4.1.52.4.13.100.2

Notifications

NameOIDStatus
sysSystemUp
NOTIFICATION-TYPE
The system up notification shall be sent when the AP is fully up and running.
1.3.6.1.4.1.52.4.13.100.2.1current
sysSystemDown
NOTIFICATION-TYPE
The system down notification shall be sent before the AP is about to reboot.
1.3.6.1.4.1.52.4.13.100.2.2current
sysRadiusServerChanged
NOTIFICATION-TYPE
The RADIUS server changed notification shall be sent when the RADIUS server has changed from Primary / Secondary to Secondary / Primary.
1.3.6.1.4.1.52.4.13.100.2.3current
dot11StationAssociation
NOTIFICATION-TYPE
The associate notification shall be sent when a station successfully associates with the Access Point. The value of the notification shall include the MAC address of the station that has associated.
1.3.6.1.4.1.52.4.13.100.2.4current
dot11StationReAssociation
NOTIFICATION-TYPE
The re-associate notification shall be sent when a station successfully re-associates with the Access Point. The value of the notification shall include the MAC address of the station that has associated.
1.3.6.1.4.1.52.4.13.100.2.5current
dot11StationAuthentication
NOTIFICATION-TYPE
The authentication notification shall be sent when a station successfully authenticates with the Access Point. The value of the notification shall include the MAC address of the station that has authenticated.
1.3.6.1.4.1.52.4.13.100.2.6current
dot11StationRequestFail
NOTIFICATION-TYPE
The station request fail shall be sent out when a station fails to associate / re-associate / authenticate with the Access Point. The notification shall include the MAC address of the station and the reason code for the failure.
1.3.6.1.4.1.52.4.13.100.2.7current
dot1xMacAddrAuthSuccess
NOTIFICATION-TYPE
The 802.1X MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the RADIUS server. The value of the notification shall include the MAC address of the station that has authenticated.
1.3.6.1.4.1.52.4.13.100.2.9current
dot1xMacAddrAuthFail
NOTIFICATION-TYPE
The 802.1X MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the RADIUS server. The value of the notification shall include the MAC address of the station that failed to authenticate.
1.3.6.1.4.1.52.4.13.100.2.10current
dot1xAuthNotInitiated
NOTIFICATION-TYPE
The 802.1X authentication not initiated notification shall be sent when a station did not initiate 802.1X authentication with the RADIUS server. The value of the notification shall include the MAC address of the station that did not initiate 802.1X authentication.
1.3.6.1.4.1.52.4.13.100.2.11current
dot1xAuthSuccess
NOTIFICATION-TYPE
The 802.1X authentication success notification shall be sent when a station successfully authenticates with the RADIUS server. The value of the notification shall include the MAC address of the station that has authenticated.
1.3.6.1.4.1.52.4.13.100.2.12current
dot1xAuthFail
NOTIFICATION-TYPE
The 802.1X authentication failure notification shall be sent when a station fails to authenticate with the RADIUS server. The value of the notification shall include the MAC address of the station that failed to authenticate.
1.3.6.1.4.1.52.4.13.100.2.13current
localMacAddrAuthSuccess
NOTIFICATION-TYPE
The Local MAC address authentication success notification shall be sent when a station successfully authenticates the MAC address with the database stored locally within the AP. The value of the notification shall include the MAC address of the station that has authenticated.
1.3.6.1.4.1.52.4.13.100.2.14current
localMacAddrAuthFail
NOTIFICATION-TYPE
The Local MAC address authentication failure notification shall be sent when a station fails to authenticate the MAC address with the database stored locally within the AP. The value of the notification shall include the MAC address of the station that has authenticated.
1.3.6.1.4.1.52.4.13.100.2.15current
pppLogonFail
NOTIFICATION-TYPE
The PPP Logon failure notification shall be sent out when the AP fails to login successfully to the PPP peer using the supplied username and password.
1.3.6.1.4.1.52.4.13.100.2.16current
iappStationRoamedFrom
NOTIFICATION-TYPE
The IAPP Station Roamed-From Notification shall be sent out whenever a station roams from another Access Point (AP) to this AP. The notification shall include the MAC address of the station and the IP address of the old AP.
1.3.6.1.4.1.52.4.13.100.2.17current
iappStationRoamedTo
NOTIFICATION-TYPE
The IAPP Station Roamed-To Notification shall be sent out whenever a station roams to another Access Point (AP) from this AP. The notification shall include the MAC address of the station and the IP address of the new AP.
1.3.6.1.4.1.52.4.13.100.2.18current
iappContextDataSent
NOTIFICATION-TYPE
The IAPP Context Data Sent notification shall be sent out whenever the context data for a station has been sent to the new AP with which the station has associated. The notification shall include the MAC address of the station and the IP address of the new AP.
1.3.6.1.4.1.52.4.13.100.2.19current
sntpServerFail
NOTIFICATION-TYPE
The sntpServerFail notification shall be sent when the AP fails to get time from the configured SNTP server.
1.3.6.1.4.1.52.4.13.100.2.20current
dot11InterfaceAFail
NOTIFICATION-TYPE
The InterfaceAFail notification shall be sent out when 802.11a wireless interface has failed.
1.3.6.1.4.1.52.4.13.100.2.21current
dot11InterfaceGFail
NOTIFICATION-TYPE
The InterfaceGFail notification shall be sent out when 802.11g wireless interface has failed.
1.3.6.1.4.1.52.4.13.100.2.22current
dot11WirelessSTPDetection
NOTIFICATION-TYPE
The WirelessSTPDetection notification shall be sent out when wireless STP packet has detected.
1.3.6.1.4.1.52.4.13.100.2.23current