CT-PRIORITY-CLASSIFY-MIB
- Registered at
- 1.3.6.1.4.1.52.4.1.2.14.5
- Namespace
- enterasys
- Source file
CT-PRIORITY-CLASSIFY-MIB- Digest
sha256:44b86d3c78bad2ffd96df33143969da8502ca12e53afca3b0dbc2907bf1f5323
Imports
| From | Symbols |
|---|---|
| CTRON-MIB-NAMES | ctPriorityExt |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
CT-PRIORITY-CLASSIFY-MIB CTRON-MIB-NAMES CTRON-OIDS SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ctPriorityExtClassifyConfig OBJECT-IDENTITY | 1.3.6.1.4.1.52.4.1.2.14.5 | |||
| pClassifyRTP OBJECT-IDENTITY | 1.3.6.1.4.1.52.4.1.2.14.5.1 | |||
| pClassifyRTPLowDelayQueuePreference OBJECT-TYPE This value represents one of eight preference levels, 0 through 7, with 0 being the worst and 7 the best. The value will be translated by the device into a three bit binary number. This value shall be used to put incoming RTP packets on an internal queue. | 1.3.6.1.4.1.52.4.1.2.14.5.1.1 | INTEGER (0..7) | read-write | mandatory |
| pClassifyRTCPParsing OBJECT-TYPE This object will enable or disable parsing of all forwarded packets looking for RTCP packets. Enabled(2) means that all fowarded packets will be parsed for RTCP. When an RTCP packet is found, the identification of the associated RTP 'connection' (next lower port number) is added to the list of low delay ports. Disabled(1) means that no packets will be parsed. | 1.3.6.1.4.1.52.4.1.2.14.5.1.2 | INTEGER {disabled(1), enabled(2)} | read-write | mandatory |
| pClassifyRTPTable OBJECT-TYPE A list describing which MIB-II interfaces will allow 802.1 P/Q tagging or modification of the precedence field in the TOS portion of an IP packet or both. It also specifies the tagging value and the TOS precedence where applicable. | 1.3.6.1.4.1.52.4.1.2.14.5.1.3 | not-accessible | mandatory | |
| pClassifyRTPEntry OBJECT-TYPE This entry for pClassifyRTPEntry. | 1.3.6.1.4.1.52.4.1.2.14.5.1.3.1 | not-accessible | mandatory | |
| pClassifyRTPInterfaceNumber OBJECT-TYPE The index of the MIB-II interface that the packet is destined for. | 1.3.6.1.4.1.52.4.1.2.14.5.1.3.1.1 | INTEGER | read-only | mandatory |
| pClassifyRTPState OBJECT-TYPE This object will enable or disable modification of the TOS precedence field and the 802.1 P/Q tagging. A value of NoModification(1) implies that modification is not allowed. OnlyQTag(2) means that only 802.1 P/Q tagging is allowed. When this object has a value OnlyQTOS(3), modification of only the TOS precedence field is permitted. QTagAndQTOS means that both TOS precedence modification and P/Q tagging is allowed. | 1.3.6.1.4.1.52.4.1.2.14.5.1.3.1.2 | INTEGER {noModification(1), onlyQTag(2), onlyQTOS(3), qTagAndQTOS(4)} | read-write | mandatory |
| pClassifyRTPTOSPrecedence OBJECT-TYPE This value represents one of eight precedence levels, 0 through 7, with 0 being the lowest and 7 the highest. The value will be translated by the device into a three bit binary number for use as the precedence field in the TOS portion of the IP Datagram. This object is valid only if pClassifyRTPState is OnlyQTOS or QTagAndQTOS. | 1.3.6.1.4.1.52.4.1.2.14.5.1.3.1.3 | INTEGER (0..7) | read-write | mandatory |
| pClassifyRTPTagPriority OBJECT-TYPE This value represents one of eight priority levels, 0 through 7, with 0 being the lowest and 7 the highest. The value will be translated by the device into a three bit binary number for use as the user_priority field of the TCI (Tag Control Information) format. This object is only valid if pClassifyRTPState is OnlyQTag or QTagAndQTOS. | 1.3.6.1.4.1.52.4.1.2.14.5.1.3.1.4 | INTEGER (0..7) | read-write | mandatory |
| pClassifyRTPTagVID OBJECT-TYPE This value represents a twelve bit VLAN identifier (VID) as specified in the IEEE 802.1Q standard. This object will provide a twelve bit VID in the TCI (Tag Control Information) portion of a tagged frame as specified in the IEEE 802.1Q. This value will be used to classify qualified packets in accordance with the IEEE 802.1Q standard. This object will also be used to reclassify certain packets exiting the port specified in pClassifyRTPInterfaceNumber whose TCI field contains a VID equal to the NULL VLAN ID. This object is valid only if pClassifyRTPState is OnlyQTag or QTagAndQTOS. | 1.3.6.1.4.1.52.4.1.2.14.5.1.3.1.5 | INTEGER (0..4095) | read-write | mandatory |
| pClassifyUDP OBJECT-IDENTITY | 1.3.6.1.4.1.52.4.1.2.14.5.2 | |||
| pClassifyUDPTable OBJECT-TYPE A list of UDP destination port numbers, UDP packets whose port numbers appear in this table will be put on a low delay queue, and the preference specified. | 1.3.6.1.4.1.52.4.1.2.14.5.2.1 | not-accessible | mandatory | |
| pClassifyUDPEntry OBJECT-TYPE A list of objects that describe the UDP port numbers that qualify as candidates for low delay queue preference classification. | 1.3.6.1.4.1.52.4.1.2.14.5.2.1.1 | not-accessible | mandatory | |
| pClassifyUDPPortNumber OBJECT-TYPE The UDP destination port number tha qualifies as a candidate for low delay classification. | 1.3.6.1.4.1.52.4.1.2.14.5.2.1.1.1 | INTEGER | read-write | mandatory |
| pClassifyUDPState OBJECT-TYPE A packet with UDP port number equal to pClassifyUDPPortNumber will be put on a low_delay queue if state is Enabled(2). | 1.3.6.1.4.1.52.4.1.2.14.5.2.1.1.2 | INTEGER {disabled(1), enabled(2), remove(3)} | read-write | mandatory |
| pClassifyUDPLowDelayQueuePreference OBJECT-TYPE Preference with which packet with UDP destination port number equal to pClassifyUDPPortNumberis put on the queue. | 1.3.6.1.4.1.52.4.1.2.14.5.2.1.1.3 | INTEGER (0..7) | read-write | mandatory |