MIBs Depot

CPS-MIB

Registered at
1.3.6.1.4.1.3808
Namespace
cyberpower
Source file
CPS-MIB
Digest
sha256:e302e8eeee193b89ce097997179192e8e3101455e8ab8f65c099f85e42073492

Imports

FromSymbols
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIGauge32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, enterprises, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CPS-MIB
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
cps
OBJECT-IDENTITY
1.3.6.1.4.1.3808
products
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1
hardware
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1
ups
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1
upsIdent
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.1
upsBaseIdent
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.1.1
upsBaseIdentModel
OBJECT-TYPE
The UPS model name.
1.3.6.1.4.1.3808.1.1.1.1.1.1DisplayStringread-onlymandatory
upsBaseIdentName
OBJECT-TYPE
The UPS identified name could be set by the administrator.
1.3.6.1.4.1.3808.1.1.1.1.1.2DisplayStringread-writemandatory
upsAdvanceIdent
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.1.2
upsAdvanceIdentFirmwareRevision
OBJECT-TYPE
The UPS firmware revision.
1.3.6.1.4.1.3808.1.1.1.1.2.1DisplayStringread-onlymandatory
upsAdvanceIdentDateOfManufacture
OBJECT-TYPE
The UPS manufacture date in mm/dd/yy format.
1.3.6.1.4.1.3808.1.1.1.1.2.2DisplayStringread-onlymandatory
upsAdvanceIdentSerialNumber
OBJECT-TYPE
The UPS serial number in the internal microprocessor.
1.3.6.1.4.1.3808.1.1.1.1.2.3DisplayStringread-onlymandatory
upsAdvanceIdentAgentFirmwareRevision
OBJECT-TYPE
The SNMP agent firmware revision.
1.3.6.1.4.1.3808.1.1.1.1.2.4DisplayStringread-onlymandatory
upsAdvanceIdentLCDFirmwareVersion
OBJECT-TYPE
The revision number of the UPS LCD firmware.
1.3.6.1.4.1.3808.1.1.1.1.2.5DisplayStringread-onlymandatory
upsAdvanceIdentPowerRating
OBJECT-TYPE
The Volt-Amp rating of the UPS.
1.3.6.1.4.1.3808.1.1.1.1.2.6INTEGERread-onlymandatory
upsAdvanceIdentLoadPower
OBJECT-TYPE
The power rating(Watts) of the UPS.
1.3.6.1.4.1.3808.1.1.1.1.2.7INTEGERread-onlymandatory
upsAdvanceIdentCurrentRating
OBJECT-TYPE
The output current rating of the UPS. Measured in tenths of Amps.
1.3.6.1.4.1.3808.1.1.1.1.2.8INTEGERread-onlymandatory
upsAdvanceIdentAgentSerialNumber
OBJECT-TYPE
A string identifying the serial number of the Agent.
1.3.6.1.4.1.3808.1.1.1.1.2.9DisplayStringread-onlymandatory
upsBattery
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.2
upsBaseBattery
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.2.1
upsBaseBatteryStatus
OBJECT-TYPE
The UPS battery status. A batteryLow(3) value means the battery will be exhausted soon under the current load. The amount of low battery run time can be configured by the upsAdvanceConfigLowBatteryRunTime.
1.3.6.1.4.1.3808.1.1.1.2.1.1INTEGER {unknown(1), batteryNormal(2), batteryLow(3), batteryNotPresent(4)}read-onlymandatory
upsBaseBatteryTimeOnBattery
OBJECT-TYPE
The UPS wasted battery time since the UPS has transfered to backup mode.
1.3.6.1.4.1.3808.1.1.1.2.1.2TimeTicksread-onlymandatory
upsBaseBatteryLastReplaceDate
OBJECT-TYPE
The UPS batteries last replaced date in mm/dd/yyyy format. This value is originally set when manufactured. If batteries replaced, administrator should reset this value.
1.3.6.1.4.1.3808.1.1.1.2.1.3DisplayStringread-writemandatory
upsBaseBatteryAgeRecommand
OBJECT-TYPE
Recommended battery life in month
1.3.6.1.4.1.3808.1.1.1.2.1.4INTEGERread-onlymandatory
upsAdvanceBattery
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.2.2
upsAdvanceBatteryCapacity
OBJECT-TYPE
The battery capacity expressed in percentage.
1.3.6.1.4.1.3808.1.1.1.2.2.1Gaugeread-onlymandatory
upsAdvanceBatteryVoltage
OBJECT-TYPE
The battery voltage expressed in 1/10 VDC.
1.3.6.1.4.1.3808.1.1.1.2.2.2INTEGERread-onlymandatory
upsAdvanceBatteryTemperature
OBJECT-TYPE
The UPS battery temperature expressed in Celsius.
1.3.6.1.4.1.3808.1.1.1.2.2.3Gaugeread-onlymandatory
upsAdvanceBatteryRunTimeRemaining
OBJECT-TYPE
The UPS battery remaining run time.
1.3.6.1.4.1.3808.1.1.1.2.2.4TimeTicksread-onlymandatory
upsAdvanceBatteryReplaceIndicator
OBJECT-TYPE
This value indicates if UPS batteries need to be replaced.
1.3.6.1.4.1.3808.1.1.1.2.2.5INTEGER {noBatteryNeedsReplacing(1), batteryNeedsReplacing(2)}read-onlymandatory
upsAdvanceBatteryFullChargeVoltage
OBJECT-TYPE
The battery charged voltage expressed in 1/10 VDC.
1.3.6.1.4.1.3808.1.1.1.2.2.6INTEGERread-onlymandatory
upsAdvanceBatteryCurrent
OBJECT-TYPE
The battery current expressed in percentage.
1.3.6.1.4.1.3808.1.1.1.2.2.7INTEGERread-onlymandatory
upsAdvanceBatteryVoltageRating
OBJECT-TYPE
The DC voltage rating of the battery set.
1.3.6.1.4.1.3808.1.1.1.2.2.8INTEGERread-onlymandatory
upsAdvanceBatteryLife
OBJECT-TYPE
The battery life expressed in 1/100 percentage.
1.3.6.1.4.1.3808.1.1.1.2.2.9INTEGERread-onlymandatory
upsInput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.3
upsBaseInput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.3.1
upsBaseInputPhase
OBJECT-TYPE
The AC input phase.
1.3.6.1.4.1.3808.1.1.1.3.1.1INTEGERread-onlymandatory
upsAdvanceInput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.3.2
upsAdvanceInputLineVoltage
OBJECT-TYPE
The input line voltage in 1/10 VAC.
1.3.6.1.4.1.3808.1.1.1.3.2.1Gaugeread-onlymandatory
upsAdvanceInputMaxLineVoltage
OBJECT-TYPE
The maximum input line voltage in 1/10 VAC over the previous 1 minute period.
1.3.6.1.4.1.3808.1.1.1.3.2.2Gaugeread-onlymandatory
upsAdvanceInputMinLineVoltage
OBJECT-TYPE
The minimum input line voltage in 1/10 VAC over the previous 1 minute period.
1.3.6.1.4.1.3808.1.1.1.3.2.3Gaugeread-onlymandatory
upsAdvanceInputFrequency
OBJECT-TYPE
The input line frequency in 1/10 Hz.
1.3.6.1.4.1.3808.1.1.1.3.2.4Gaugeread-onlymandatory
upsAdvanceInputLineFailCause
OBJECT-TYPE
The reason of UPS power failure. This value is set to: - noTransfer(1), if UPS is in utility mode. - highLineVoltage(2), if UPS switch to battery mode by reason of input voltage over the high transfer vloltage. - brownout(3), if UPS switch to battery mode by reason of input voltage under the low transfer vloltage. - selfTest(4), if the UPS was commanded to do a self test.
1.3.6.1.4.1.3808.1.1.1.3.2.5INTEGER {noTransfer(1), highLineVoltage(2), brownout(3), selfTest(4)}read-onlymandatory
upsAdvanceInputStatus
OBJECT-TYPE
Display the present status of the utility power supplied to the UPS.
1.3.6.1.4.1.3808.1.1.1.3.2.6INTEGER {normal(1), overVoltage(2), underVoltage(3), frequencyFailure(4), blackout(5)}read-onlymandatory
upsOutput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.4
upsBaseOutput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.4.1
upsBaseOutputStatus
OBJECT-TYPE
The UPS output status.
1.3.6.1.4.1.3808.1.1.1.4.1.1INTEGER {unknown(1), onLine(2), onBattery(3), onBoost(4), onSleep(5), off(6), rebooting(7), onECO(8), onBypass(9), onBuck(10), onOverload(11)}read-onlymandatory
upsBaseOutputPhase
OBJECT-TYPE
The output phase.
1.3.6.1.4.1.3808.1.1.1.4.1.2INTEGERread-onlymandatory
upsBaseOutputWorkingFrequency
OBJECT-TYPE
The frequency of the UPS output power.
1.3.6.1.4.1.3808.1.1.1.4.1.3DisplayStringread-onlymandatory
upsAdvanceOutput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.4.2
upsAdvanceOutputVoltage
OBJECT-TYPE
The UPS output voltage in 1/10 VAC.
1.3.6.1.4.1.3808.1.1.1.4.2.1Gaugeread-onlymandatory
upsAdvanceOutputFrequency
OBJECT-TYPE
The UPS output frequency in 1/10 Hz.
1.3.6.1.4.1.3808.1.1.1.4.2.2Gaugeread-onlymandatory
upsAdvanceOutputLoad
OBJECT-TYPE
The UPS output load expressed in percentage
1.3.6.1.4.1.3808.1.1.1.4.2.3Gaugeread-onlymandatory
upsAdvanceOutputCurrent
OBJECT-TYPE
The UPS output current in 1/10 Amps.
1.3.6.1.4.1.3808.1.1.1.4.2.4Gaugeread-onlymandatory
upsAdvanceOutputPower
OBJECT-TYPE
The total output active power of the UPS system in W.
1.3.6.1.4.1.3808.1.1.1.4.2.5Gaugeread-onlymandatory
upsConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.5
upsBaseConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.5.1
upsBaseConfigNumDevices
OBJECT-TYPE
The number of equipment plugged into the UPS.
1.3.6.1.4.1.3808.1.1.1.5.1.1INTEGERread-onlymandatory
upsBaseConfigDeviceTable
OBJECT-TYPE
A list of equipment plugged into the UPS. The numbers of entries are given by the value of upsBaseConfigNumDevices.
1.3.6.1.4.1.3808.1.1.1.5.1.2not-accessiblemandatory
upsBaseConfigDeviceEntry
OBJECT-TYPE
The equipment plugged in to the UPS.
1.3.6.1.4.1.3808.1.1.1.5.1.2.1not-accessiblemandatory
deviceIndex
OBJECT-TYPE
The index of the equipment plugged into the UPS.
1.3.6.1.4.1.3808.1.1.1.5.1.2.1.1INTEGER (1..255)read-onlymandatory
deviceName
OBJECT-TYPE
The name of the equipment plugged into the UPS.
1.3.6.1.4.1.3808.1.1.1.5.1.2.1.2DisplayStringread-writemandatory
vaRating
OBJECT-TYPE
The VA rating of the equipment plugged into the UPS.
1.3.6.1.4.1.3808.1.1.1.5.1.2.1.3INTEGERread-writemandatory
acceptThisDevice
OBJECT-TYPE
An equipment is plugged if yes, unplugged if no.
1.3.6.1.4.1.3808.1.1.1.5.1.2.1.4INTEGER {yes(1), no(2)}read-writemandatory
upsAdvanceConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.5.2
upsAdvanceConfigOutputVoltage
OBJECT-TYPE
The standard UPS output voltage in VAC. The possible values are 100, 110, 120, 127, 208, 220, 230, and 240. If a value other than a possible value is set, it will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.1INTEGERread-writemandatory
upsAdvanceConfigHighTransferVolt
OBJECT-TYPE
Adjust the high transfer vloltage in VAC. The high transfer vloltage will become the UPS default value subtracts this value. The allowed values depend on the output: 100-127 volt system allow settings of 0-15. 208-240 volt system allow settings of 0-30. If the adjustable value is over the allowed values, it will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.2INTEGERread-writemandatory
upsAdvanceConfigLowTransferVolt
OBJECT-TYPE
Adjust the low transfer vloltage in VAC. The low transfer vloltage will become the UPS default value adds this value. The allowed values depend on the output: 100-127 volt system allow settings of 0-15. 208-240 volt system allow settings of 0-30. If the adjustable value is over the allowed values, it will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.3INTEGERread-writemandatory
upsAdvanceConfigAlarm
OBJECT-TYPE
This value is set to handle audible alarms when power failure.
1.3.6.1.4.1.3808.1.1.1.5.2.4INTEGER {timed(1), enable(2), disable(3), mute(4)}read-writemandatory
upsAdvanceConfigAlarmTimer
OBJECT-TYPE
The time after power failure at which the UPS begins giving audible alarms. This timer is effective only if the value of upsAdvanceConfigAlarm is timed(1). Accepted values are between 0 to 60 seconds. If a value other than a supported value is set, the value will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.5TimeTicksread-writemandatory
upsAdvanceConfigMinReturnCapacity
OBJECT-TYPE
The minimum battery capacity that UPS will return from a low battery shutdown condition. The possible values are between 0 to 40. If a value other than a supported value is set, the value will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.6INTEGERread-writemandatory
upsAdvanceConfigSensitivity
OBJECT-TYPE
The sensitivity of the UPS to power failure detection.
1.3.6.1.4.1.3808.1.1.1.5.2.7INTEGER {auto(1), low(2), medium(3), high(4)}read-writemandatory
upsAdvanceConfigLowBatteryRunTime
OBJECT-TYPE
The desired run time, in seconds, UPS will enter in a low battery sequence. The possible values are 120, 300, 420, 600. If a value other than a supported value is set, the value will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.8TimeTicksread-writemandatory
upsAdvanceConfigReturnDelay
OBJECT-TYPE
The delay time the UPS will turn on after power recovery. The value is also used in a 'reboot' or 'wake up' sequence. The possible values are 0 to 600 seconds. If a value other than a supported value is set, the value will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.9TimeTicksread-writemandatory
upsAdvanceConfigShutoffDelay
OBJECT-TYPE
The delay time the UPS will remain on after receiving a turn off command. The possible values are between 60 to 5940 seconds. If a value other than a supported value is set, the value will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.10TimeTicksread-writemandatory
upsAdvanceConfigSleepDelay
OBJECT-TYPE
The delay time the UPS will enter sleep mode after receiving a sleep command. WThe possible values are between 60 to 5940 seconds. If a value other than a supported value is set, the value will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.11TimeTicksread-writemandatory
upsAdvanceConfigSetEEPROMDefaults
OBJECT-TYPE
Reset the UPS EEPROM parameters to default values.
1.3.6.1.4.1.3808.1.1.1.5.2.12INTEGER {noSetEEPROMDefaults(1), setEEPROMDefaults(2)}read-writemandatory
upsAdvanceConfigAutoRestore
OBJECT-TYPE
When this option is enabled, the UPS will restore output immediately when the utility power restores.When this option is disabled, the UPS will not restore output at that moment and users have to turn it on manually at a later time.
1.3.6.1.4.1.3808.1.1.1.5.2.13INTEGER {disable(1), enable(2)}read-writemandatory
upsAdvanceConfigRechargedCapacity
OBJECT-TYPE
When the utility power restores, the UPS will start to recharge until the specified battery capacity in percentage is met before restoring output power. The possible values are 0, 15, 30, 45, 60, 75, and 90. If a value other than a possible value is set, it will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.14INTEGERread-writemandatory
upsAdvanceConfigColdStart
OBJECT-TYPE
Set the ability of the UPS can start in the absence of input power.When this option is enabled the UPS can be turned on without having input power.
1.3.6.1.4.1.3808.1.1.1.5.2.15INTEGER {disable(1), enable(2)}read-writemandatory
upsAdvanceConfigDeepDischargeProtection
OBJECT-TYPE
When the UPS is on Battery Mode with 0% load and the status remains for the time configured,the RMCARD will enforce the UPS to Sleep Mode and the output will be turned off. The possible values are 0, 20, 40, and 60 minutes. If a value other than a possible value is set, it will not be accepted.
1.3.6.1.4.1.3808.1.1.1.5.2.16INTEGERread-writemandatory
upsAdvanceConfigSleepAfterAllClientShut
OBJECT-TYPE
If this option is enabled, UPS will enter sleep mode after utility power failed and remaining MSDT+2 minutes.More information about MSDT please reference to help page of UPS - > PowerPanel List.
1.3.6.1.4.1.3808.1.1.1.5.2.17INTEGER {disable(1), enable(2)}read-writemandatory
upsAdvanceConfigLowBatteryThreshold
OBJECT-TYPE
When the UPS supplies battery power and the remaining capacity is lower than this threshold, the UPS will sound an alarm. The value expressed in percentage.
1.3.6.1.4.1.3808.1.1.1.5.2.18INTEGERread-writemandatory
upsControl
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.6
upsBaseControl
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.6.1
upsBaseControlConserveBattery
OBJECT-TYPE
UPS on battery will enter sleeping when the variable is set to turnOffUpsToConserveBattery(2). When utility power recovers the UPS will turn back on. Trying to turn off a UPS that is not on battery mode will cause badValue error. It is no effective to set this value to noTurnOffUps(1).
1.3.6.1.4.1.3808.1.1.1.6.1.1INTEGER {noTurnOffUps(1), turnOffUpsToConserveBattery(2)}read-writemandatory
upsAdvanceControl
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.6.2
upsAdvanceControlUpsOff
OBJECT-TYPE
UPS will shutdown when the variable is set to turnUpsOff(2). UPS will shutdown after a delay period specified by upsAdvanceConfigShutoffDelay when the variable is Set to turnUpsOffGracefully(3). Without regard to the utility state the UPS will not provide output power in this state. It is no effective to set this value to noTurnUpsOff(1).
1.3.6.1.4.1.3808.1.1.1.6.2.1INTEGER {noTurnUpsOff(1), turnUpsOff(2), turnUpsOffGracefully(3)}read-writemandatory
upsAdvanceControlRebootUps
OBJECT-TYPE
UPS will shutdown and turn back on when the variable is set to rebootUps(2). It is no effective to set this value to noRebootUps(1).
1.3.6.1.4.1.3808.1.1.1.6.2.2INTEGER {noRebootUps(1), rebootUps(2)}read-writemandatory
upsAdvanceControlUpsSleep
OBJECT-TYPE
UPS will enter sleep mode when the variable is set to putUpsToSleep(2). UPS will enter sleep mode after a delay period specified by upsAdvanceConfigSleepDelay when the variable is Set to putUpsToSleepGracefully(3). Without regard to the utility state the UPS will not provide output power in sleep mode. Output power will recover when specified time has elapsed. It is no effective to set this value to noPutUpsToSleep(1).
1.3.6.1.4.1.3808.1.1.1.6.2.3INTEGER {noPutUpsToSleep(1), putUpsToSleep(2), putUpsToSleepGracefully(3)}read-writemandatory
upsAdvanceControlSimulatePowerFail
OBJECT-TYPE
UPS will transfer to backup mode when the variable is set to simulatePowerFailure(2). It is no effective to set this value to noFlashAndBeep(1).
1.3.6.1.4.1.3808.1.1.1.6.2.4INTEGER {noSimulatePowerFailure(1), simulatePowerFailure(2)}read-writemandatory
upsAdvanceControlFlashAndBeep
OBJECT-TYPE
UPS will beep and simultaneously turn on the panel lights when the variable is set to flashAndBeep(2). It is no effective to set this value to noSimulatePowerFailure(1).
1.3.6.1.4.1.3808.1.1.1.6.2.5INTEGER {noFlashAndBeep(1), flashAndBeep(2)}read-writemandatory
upsAdvanceControlTurnOnUPS
OBJECT-TYPE
UPS will turned on immediately when the variable is set to turnOnUPS(2). It is no effective to set this value to noTurnOnUPS(1).
1.3.6.1.4.1.3808.1.1.1.6.2.6INTEGER {noTurnOnUPS(1), turnOnUPS(2)}read-writemandatory
upsAdvanceSleepAfterDelay
OBJECT-TYPE
UPS will enter sleep mode after indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown.
1.3.6.1.4.1.3808.1.1.1.6.2.7INTEGER (-1..600)read-writemandatory
upsTest
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.7
upsBaseTest
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.7.1
upsAdvanceTest
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.7.2
upsAdvanceTestDiagnosticSchedule
OBJECT-TYPE
The schedule of the UPS automatic selftest.
1.3.6.1.4.1.3808.1.1.1.7.2.1INTEGER {unknown(1), biweekly(2), weekly(3), atTurnOn(4), never(5)}read-writemandatory
upsAdvanceTestDiagnostics
OBJECT-TYPE
UPS will do a diagnostic selftest when the variable is set to testDiagnostics(2). It is no effective to set this value to noTestDiagnostics(1).
1.3.6.1.4.1.3808.1.1.1.7.2.2INTEGER {noTestDiagnostics(1), testDiagnostics(2)}read-writemandatory
upsAdvanceTestDiagnosticsResults
OBJECT-TYPE
The last UPS selftest result.
1.3.6.1.4.1.3808.1.1.1.7.2.3INTEGER {ok(1), failed(2), invalidTest(3), testInProgress(4)}read-onlymandatory
upsAdvanceTestLastDiagnosticsDate
OBJECT-TYPE
The last UPS selftest date in mm/dd/yy format.
1.3.6.1.4.1.3808.1.1.1.7.2.4DisplayStringread-onlymandatory
upsAdvanceTestIndicators
OBJECT-TYPE
UPS will perform a panel indicator test when the variable is set to testIndicators(2). It is no effective to set this value to noTestIndicators(1).
1.3.6.1.4.1.3808.1.1.1.7.2.5INTEGER {noTestIndicators(1), testIndicators(2)}read-writemandatory
upsAdvanceTestRuntimeEstimation
OBJECT-TYPE
UPS will discharge to calibrate the UPS runtime when the variable is set to performEstimation(2). This test runs until the UPS is in a low battery condition. UPS will cancel the discharge after setting performEstimation(2) when the variable is set to cancelCurrentEstimation(3). It is no effective to set this value to noPerformEstimation(1). The result of the runtime test will be stored in upsAdvanceTestEstimationResults.
1.3.6.1.4.1.3808.1.1.1.7.2.6INTEGER {noPerformEstimation(1), performEstimation(2), cancelCurrentEstimation(3)}read-writemandatory
upsAdvanceTestEstimationResults
OBJECT-TYPE
The last runtime estimation result. This value means : - ok(1), if a successful runtime estimation. - invalidEstimation(2), if runtime estimation failure. - estimationInProgress(3), if estimation is processing now.
1.3.6.1.4.1.3808.1.1.1.7.2.7INTEGER {ok(1), invalidEstimation(2), estimationInProgress(3)}read-onlymandatory
upsAdvanceTestEstimationDate
OBJECT-TYPE
The last UPS runtime estimation date
1.3.6.1.4.1.3808.1.1.1.7.2.8DisplayStringread-onlymandatory
upsOutlet
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.8
upsBankOutletControl
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.8.1
upsBankOutletControlTable
OBJECT-TYPE
Allows for control of the outlet banks.
1.3.6.1.4.1.3808.1.1.1.8.1.1not-accessiblemandatory
upsBankOutletControlEntry
OBJECT-TYPE
The outlet to control.
1.3.6.1.4.1.3808.1.1.1.8.1.1.1not-accessiblemandatory
upsBankControlIndex
OBJECT-TYPE
The index to the outlet entry.
1.3.6.1.4.1.3808.1.1.1.8.1.1.1.1INTEGER (1..24)read-onlymandatory
upsBankControlOutletCommand
OBJECT-TYPE
Getting this variable will return the outlet bank state. If the outlet bank is on, the immediateOn (1) value will be returned. If the outlet bank is off, the immediateOff (2) value will be returned. If the outlet bank is critical (uncontrollable), the criticalBank (4) value will be returned. Setting this variable to immediateOn (1) will immediately turn the outlet on. Setting this variable to immediateOff (2) will immediately turn the outlet off.
1.3.6.1.4.1.3808.1.1.1.8.1.1.1.2INTEGER {immediateOn(1), immediateOff(2), bankNotExist(3), criticalBank(4)}read-writemandatory
upsPhase
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.9
upsPhaseInput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.9.1
upsPhaseInputTableSize
OBJECT-TYPE
Getting this OID will return the phase number.
1.3.6.1.4.1.3808.1.1.1.9.1.1INTEGERread-onlymandatory
upsPhaseInputTable
OBJECT-TYPE
Allows for getting the Phase Input in the UPS
1.3.6.1.4.1.3808.1.1.1.9.1.2not-accessiblemandatory
upsPhaseInputEntry
OBJECT-TYPE
The UPS Phase Input Access.
1.3.6.1.4.1.3808.1.1.1.9.1.2.1not-accessiblemandatory
upsPhaseInputTableIndex
OBJECT-TYPE
The index to the UPS Phase Input entry.
1.3.6.1.4.1.3808.1.1.1.9.1.2.1.1INTEGER (3)read-onlymandatory
upsPhaseInputVoltage
OBJECT-TYPE
Getting this OID will return the input voltage that each phase of the UPS can provide. It is represented in 1/10 VAC.
1.3.6.1.4.1.3808.1.1.1.9.1.2.1.2INTEGERread-onlymandatory
upsPhaseInputCurrent
OBJECT-TYPE
Getting this OID will return the input current that each phase of the UPS can provide. It is represented in 1/10 Amps.
1.3.6.1.4.1.3808.1.1.1.9.1.2.1.3INTEGERread-onlymandatory
upsPhaseInputFrequency
OBJECT-TYPE
Getting this OID will return the input frequency that each phase of the UPS can provide. It is represented in 1/10 Hz.
1.3.6.1.4.1.3808.1.1.1.9.1.2.1.4INTEGERread-onlymandatory
upsPhaseInputPowerFactor
OBJECT-TYPE
Getting this OID will return the input power factor that each phase of the UPS can provide. It is represented in 1/100.
1.3.6.1.4.1.3808.1.1.1.9.1.2.1.5INTEGERread-onlymandatory
upsPhaseOutput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.9.2
upsPhaseOutputTableSize
OBJECT-TYPE
Getting this OID will return the Phase number.
1.3.6.1.4.1.3808.1.1.1.9.2.1INTEGERread-onlymandatory
upsPhaseOutputTable
OBJECT-TYPE
Allows for getting the Phase Output in the UPS
1.3.6.1.4.1.3808.1.1.1.9.2.2not-accessiblemandatory
upsPhaseOutputEntry
OBJECT-TYPE
The UPS Phase Output Access.
1.3.6.1.4.1.3808.1.1.1.9.2.2.1not-accessiblemandatory
upsPhaseOutputTableIndex
OBJECT-TYPE
The index to the UPS Phase Output entry.
1.3.6.1.4.1.3808.1.1.1.9.2.2.1.1INTEGER (3)read-onlymandatory
upsPhaseOutputVoltage
OBJECT-TYPE
Getting this OID will return the output voltage that each phase of the UPS can provide. It is represented in 1/10 VAC.
1.3.6.1.4.1.3808.1.1.1.9.2.2.1.2INTEGERread-onlymandatory
upsPhaseOutputCurrent
OBJECT-TYPE
Getting this OID will return the output current that each phase of the UPS can provide. It is represented in 1/10 Amps.
1.3.6.1.4.1.3808.1.1.1.9.2.2.1.3INTEGERread-onlymandatory
upsPhaseOutputFrequency
OBJECT-TYPE
Getting this OID will return the output frequency that each phase of the UPS can provide. It is represented in 1/10 Hz.
1.3.6.1.4.1.3808.1.1.1.9.2.2.1.4INTEGERread-onlymandatory
upsPhaseOutputPowerFactor
OBJECT-TYPE
Getting this OID will return the output power factor that each phase of the UPS can provide. It is represented in 1/100.
1.3.6.1.4.1.3808.1.1.1.9.2.2.1.5INTEGERread-onlymandatory
upsPhaseOutputPower
OBJECT-TYPE
Getting this OID will return the output power that each phase of the UPS can provide. It is represented in Watt.
1.3.6.1.4.1.3808.1.1.1.9.2.2.1.6INTEGERread-onlymandatory
upsPhaseBypass
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.9.3
upsPhaseBypassTableSize
OBJECT-TYPE
Getting this OID will return the Phase number.
1.3.6.1.4.1.3808.1.1.1.9.3.1INTEGERread-onlymandatory
upsPhaseBypassTable
OBJECT-TYPE
Allows for getting the Phase Bypass in the UPS
1.3.6.1.4.1.3808.1.1.1.9.3.2not-accessiblemandatory
upsPhaseBypassEntry
OBJECT-TYPE
The UPS Phase Bypass Access.
1.3.6.1.4.1.3808.1.1.1.9.3.2.1not-accessiblemandatory
upsPhaseBypassTableIndex
OBJECT-TYPE
The index to the UPS Phase Bypass entry.
1.3.6.1.4.1.3808.1.1.1.9.3.2.1.1INTEGER (3)read-onlymandatory
upsPhaseBypassVoltage
OBJECT-TYPE
Getting this OID will return the bypass voltage that each phase of the UPS can provide. It is represented in 1/10 VAC.
1.3.6.1.4.1.3808.1.1.1.9.3.2.1.2INTEGERread-onlymandatory
upsPhaseBypassCurrent
OBJECT-TYPE
Getting this OID will return the bypass current that each phase of the UPS can provide. It is represented in 1/10 Amps.
1.3.6.1.4.1.3808.1.1.1.9.3.2.1.3INTEGERread-onlymandatory
upsPhaseBypassFrequency
OBJECT-TYPE
Getting this OID will return the bypass frequency that each phase of the UPS can provide. It is represented in 1/10 Hz.
1.3.6.1.4.1.3808.1.1.1.9.3.2.1.4INTEGERread-onlymandatory
upsPhaseBypassPowerFactor
OBJECT-TYPE
Getting this OID will return the bypass power factor that each phase of the UPS can provide. It is represented in 1/100.
1.3.6.1.4.1.3808.1.1.1.9.3.2.1.5INTEGERread-onlymandatory
upsSystem
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.1.10
upsStatus
OBJECT-TYPE
The UPS system status.
1.3.6.1.4.1.3808.1.1.1.10.1INTEGER {normal(1), overheat(2), hardwarefault(3)}read-onlymandatory
eswitch
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.2
eSwitchIdent
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.2.1
eSwitchIdentHardwareRev
OBJECT-TYPE
The hardware revision set at the factory.
1.3.6.1.4.1.3808.1.1.2.1.1DisplayStringread-onlymandatory
eSwitchIdentFirmwareRev
OBJECT-TYPE
The firmware revision set at the factory.
1.3.6.1.4.1.3808.1.1.2.1.2DisplayStringread-onlymandatory
eSwitchIdentDateOfManufacture
OBJECT-TYPE
The manufacture date in mm/dd/yy format.
1.3.6.1.4.1.3808.1.1.2.1.3DisplayStringread-onlymandatory
eSwitchIdentModelName
OBJECT-TYPE
The model name set at the factory. This value need to consist with safty report.
1.3.6.1.4.1.3808.1.1.2.1.4DisplayStringread-onlymandatory
eSwitchBase
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.2.2
eSwitchNumber
OBJECT-TYPE
The numbers of switch have been attached to the system.
1.3.6.1.4.1.3808.1.1.2.2.1INTEGERread-onlymandatory
eSwitchBaseTable
OBJECT-TYPE
A list of switch information. The number of entries is given by the value of eSwitchNumber.
1.3.6.1.4.1.3808.1.1.2.2.2not-accessiblemandatory
eSwitchBaseEntry
OBJECT-TYPE
An entry information of the individual switch.
1.3.6.1.4.1.3808.1.1.2.2.2.1not-accessiblemandatory
eSwitchID
OBJECT-TYPE
The power switch ID number.
1.3.6.1.4.1.3808.1.1.2.2.2.1.1INTEGER (0..16)read-onlymandatory
eSwitchOutletNum
OBJECT-TYPE
The number of outlets provided in the switch.
1.3.6.1.4.1.3808.1.1.2.2.2.1.2INTEGERread-onlymandatory
eSwitchOutletState
OBJECT-TYPE
Getting this OID will reply the status of all outlets in the switch. '0' for outlet off, '1' for outlet on. The index from left to right is outlet#8, #7, #6, #5, #4, #3, #2, #1. For Example: If the string is '01011010', it means the outlets status are the following: outlet #8 is off, outlet #7 is on, outlet #6 is off, outlet #5 is on, outlet #4 is on, outlet #3 is off, outlet #2 is on, outlet #1 is off.
1.3.6.1.4.1.3808.1.1.2.2.2.1.3DisplayStringread-onlymandatory
eSwitchBaseCtrTable
OBJECT-TYPE
A list of switch control parameters. The number of entries is given by the value of eSwitchNumber.
1.3.6.1.4.1.3808.1.1.2.2.3not-accessiblemandatory
eSwitchBaseCtrEntry
OBJECT-TYPE
An entry control information of individual switches.
1.3.6.1.4.1.3808.1.1.2.2.3.1not-accessiblemandatory
eSwitchCtrID
OBJECT-TYPE
Select the switch ID to be controlled.
1.3.6.1.4.1.3808.1.1.2.2.3.1.1INTEGER (0..16)read-writemandatory
eSwitchActOutlet
OBJECT-TYPE
The action outlets to be controlled.
1.3.6.1.4.1.3808.1.1.2.2.3.1.2INTEGERread-writemandatory
eSwitchActType
OBJECT-TYPE
The on/off type of the action outlets. 1 for duration off, 2 for duration on, 3 for immediately off, 4 for immediately on, and 5 for reboot.
1.3.6.1.4.1.3808.1.1.2.2.3.1.3INTEGERread-writemandatory
ePDU
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3
ePDUIdent
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.1
ePDUIdentName
OBJECT-TYPE
The name of the Rack PDU. The maximum string size is device dependent.
1.3.6.1.4.1.3808.1.1.3.1.1DisplayStringread-writemandatory
ePDUIdentHardwareRev
OBJECT-TYPE
The hardware revision of the Rack PDU. This value is set at the factory.
1.3.6.1.4.1.3808.1.1.3.1.2DisplayStringread-onlymandatory
ePDUIdentFirmwareRev
OBJECT-TYPE
An 8-byte ID string identifying the Rack PDU firmware revision. This value is set at the factory.
1.3.6.1.4.1.3808.1.1.3.1.3DisplayStringread-onlymandatory
ePDUIdentDateOfManufacture
OBJECT-TYPE
The date when the Rack PDU was manufactured in mm/dd/yyyy format. This value is set at the factory. The year 2000 will be represented by 00.
1.3.6.1.4.1.3808.1.1.3.1.4DisplayStringread-onlymandatory
ePDUIdentModelNumber
OBJECT-TYPE
A 10-character string identifying the model number of the Rack PDU. This value is set at the factory.
1.3.6.1.4.1.3808.1.1.3.1.5DisplayStringread-onlymandatory
ePDUIdentSerialNumber
OBJECT-TYPE
A 12-character string identifying the serial number of the Rack PDU. This value is set at the factory.
1.3.6.1.4.1.3808.1.1.3.1.6DisplayStringread-onlymandatory
ePDUIdentDeviceRating
OBJECT-TYPE
Getting this OID will return the electrical rating of the device.
1.3.6.1.4.1.3808.1.1.3.1.7INTEGERread-onlymandatory
ePDUIdentDeviceNumOutlets
OBJECT-TYPE
Getting this OID will return the number of outlets contained in the device.
1.3.6.1.4.1.3808.1.1.3.1.8INTEGERread-onlymandatory
ePDUIdentDeviceNumPhases
OBJECT-TYPE
Getting this OID will return the number of phases supported by the device.
1.3.6.1.4.1.3808.1.1.3.1.9INTEGERread-onlymandatory
ePDUIdentDeviceNumBreakers
OBJECT-TYPE
Getting this OID will return the number of circuit breakers supported by the device. This is the same as the number of banks of outlets. 0 will be returned if the unit has no phase breakers.
1.3.6.1.4.1.3808.1.1.3.1.10INTEGERread-onlymandatory
ePDUIdentDeviceBreakerRating
OBJECT-TYPE
Getting this OID will return rating of the circuit breakers on the device if it has any.
1.3.6.1.4.1.3808.1.1.3.1.11INTEGERread-onlymandatory
ePDUIdentDeviceOrientation
OBJECT-TYPE
Getting this OID will return the intended physical orientation of the device. OrientHorizonatal(1) indicates Horizontal. OrientVertical(2) indicates Vertical.
1.3.6.1.4.1.3808.1.1.3.1.12INTEGER {orientHorizontal(1), orientVertical(2)}read-onlymandatory
ePDUIdentDeviceOutletLayout
OBJECT-TYPE
Getting this OID will return outlet layout for the device. SeqPhaseToNeutral(1) indicates outlet layout as follows: 1:1-N,2:2-N,3:3-N,4:1-N,5:2-N,... SeqPhaseToPhase(2) indicates outlet layout as follows: 1:1-2,2:2-3,3:3-1,4:1-2,5:2-3,... SeqPhToNeu21PhToPh(3) indicates outlet layout as follows: 1:1-N,2:2-N...21:3-N,22:1-2,23:2-3,24:3-1,... SeqPhToPhGrouped(4) indicates outlet layout as follows: Otlts1-8::(3-1),Otlts9-16::(2-3),Otlts17-24::(1-2).
1.3.6.1.4.1.3808.1.1.3.1.13INTEGER {seqPhaseToNeutral(1), seqPhaseToPhase(2), seqPhToNeu21PhToPh(3), seqPhToPhGrouped(4)}read-onlymandatory
ePDUIdentDeviceDisplayOrientation
OBJECT-TYPE
Getting this OID will return the intended physical orientation of the Seven-Segment Display. displayNormal(1) indicates Normal. displayReverse(2)indicates Upside-Down. displayRotate90(3) indicates rotate 90 degree. displayRotate270(4) indicates rotate 270 degree. displayAuto(5) indicates auto-detect and rotate.
1.3.6.1.4.1.3808.1.1.3.1.14INTEGER {displayNormal(1), displayReverse(2), displayRotate90(3), displayRotate270(4), displayAuto(5)}read-writemandatory
ePDUIdentDeviceLinetoLineVoltage
OBJECT-TYPE
Getting/Setting this OID will return/set the Line to Line Volatage. The valid range is between 0V to 440V
1.3.6.1.4.1.3808.1.1.3.1.15INTEGERread-writemandatory
ePDUIdentIndicator
OBJECT-TYPE
PDU will perform a panel indicator test when the variable is set to testIndicators(2). It is no effective to set this value to noTestIndicators(1).
1.3.6.1.4.1.3808.1.1.3.1.16INTEGER {noTestIndicators(1), testIndicators(2)}read-writemandatory
ePDULoad
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.2
ePDULoadDevice
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.2.1
ePDULoadDevMaxPhaseLoad
OBJECT-TYPE
Getting this OID will return the maximum rated power that each phase of the Rack PDU can provide. It is represented in Amps. 0 will be returned if the unit is banked.
1.3.6.1.4.1.3808.1.1.3.2.1.1INTEGERread-onlymandatory
ePDULoadDevNumPhases
OBJECT-TYPE
The number of phases available with this Rack PDU.
1.3.6.1.4.1.3808.1.1.3.2.1.2INTEGERread-onlymandatory
ePDULoadDevMaxBankLoad
OBJECT-TYPE
Getting this OID will return the maximum rated power that a bank of the Rack PDU can provide. It is represented in Amps. 0 will be returned if the device does not have any banks.
1.3.6.1.4.1.3808.1.1.3.2.1.3INTEGERread-onlymandatory
ePDULoadDevNumBanks
OBJECT-TYPE
The number of banks of outlets available with this Rack PDU. A bank of outlets has a unique circuit breaker for a subset of the total number of outlets on the ePDU. 0 will be returned if the unit no banks.
1.3.6.1.4.1.3808.1.1.3.2.1.4INTEGERread-onlymandatory
ePDULoadDevBankTableSize
OBJECT-TYPE
The size of the Bank Table.
1.3.6.1.4.1.3808.1.1.3.2.1.5INTEGERread-onlymandatory
ePDULoadDevBankTable
OBJECT-TYPE
Allows for getting the Bank Max Load in the Rack PDU.
1.3.6.1.4.1.3808.1.1.3.2.1.6not-accessiblemandatory
ePDULoadDevBankEntry
OBJECT-TYPE
The Rack PDU Banks Access.
1.3.6.1.4.1.3808.1.1.3.2.1.6.1not-accessiblemandatory
ePDULoadDevBankIndex
OBJECT-TYPE
The index to the Rack PDU bank entry.
1.3.6.1.4.1.3808.1.1.3.2.1.6.1.1INTEGER (1..10)read-onlymandatory
ePDULoadDevBankNumber
OBJECT-TYPE
Getting this OID will return the bank number.
1.3.6.1.4.1.3808.1.1.3.2.1.6.1.2INTEGERread-onlymandatory
ePDULoadDevBankMaxLoad
OBJECT-TYPE
Getting this OID will return the maximum rated power that each bank of the Rack PDU can provide. It is represented in Amps.
1.3.6.1.4.1.3808.1.1.3.2.1.6.1.3INTEGERread-onlymandatory
ePDULoadDevMaxOutletTableSize
OBJECT-TYPE
The size of the Outlet Table.
1.3.6.1.4.1.3808.1.1.3.2.1.7INTEGERread-onlymandatory
ePDULoadDevMaxOutletTable
OBJECT-TYPE
Allows for getting the Max Outlet Load in an Outlet Monitored Rack PDU.
1.3.6.1.4.1.3808.1.1.3.2.1.8not-accessiblemandatory
ePDULoadDevMaxOutletEntry
OBJECT-TYPE
This gives access to Max Outlet Load of an Outlet Monitored Rack PDU
1.3.6.1.4.1.3808.1.1.3.2.1.8.1not-accessiblemandatory
ePDULoadDevOutletIndex
OBJECT-TYPE
The index to the Outlet Monitored Rack PDU Max Outlet Load entry.
1.3.6.1.4.1.3808.1.1.3.2.1.8.1.1INTEGER (1..24)read-onlymandatory
ePDULoadDevOutletNumber
OBJECT-TYPE
Getting this OID will return the Outlet number.
1.3.6.1.4.1.3808.1.1.3.2.1.8.1.2INTEGERread-onlymandatory
ePDULoadDevMaxOutletLoad
OBJECT-TYPE
Getting this OID will return the maximum rated power that each Outlet of an Outlet Monitored Rack PDU can provide. It is represented in Amps.
1.3.6.1.4.1.3808.1.1.3.2.1.8.1.3INTEGERread-onlymandatory
ePDULoadPhaseConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.2.2
ePDULoadPhaseConfigTable
OBJECT-TYPE
Allows for configuration of each Rack PDU phase. The number of entries is contained in the ePDULoadDevNumPhases OID.
1.3.6.1.4.1.3808.1.1.3.2.2.1not-accessiblemandatory
ePDULoadPhaseConfigEntry
OBJECT-TYPE
The Rack PDU phase to configure.
1.3.6.1.4.1.3808.1.1.3.2.2.1.1not-accessiblemandatory
ePDULoadPhaseConfigIndex
OBJECT-TYPE
The index to the Rack PDU phase entry.
1.3.6.1.4.1.3808.1.1.3.2.2.1.1.1INTEGER {phase1(1), phase2(2), phase3(3)}read-onlymandatory
ePDULoadPhaseConfigLowLoadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in Amps. A warning will be issued when the load is less than the threshold value. A threshold value of 0 Amps effectively disables this warning. Maximum value must be less than the value returned by the ePDULoadPhaseConfigNearOverloadThreshold OID.
1.3.6.1.4.1.3808.1.1.3.2.2.1.1.2INTEGERread-writemandatory
ePDULoadPhaseConfigNearOverloadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than the value returned by the ePDULoadPhaseConfigLowLoadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadPhaseConfigOverloadThreshold OID.
1.3.6.1.4.1.3808.1.1.3.2.2.1.1.3INTEGERread-writemandatory
ePDULoadPhaseConfigOverloadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than or equal to the value returned by the ePDULoadPhaseConfigNearOverloadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadDevMaxPhaseLoad OID.
1.3.6.1.4.1.3808.1.1.3.2.2.1.1.4INTEGERread-writemandatory
ePDULoadPhaseConfigAlarm
OBJECT-TYPE
Getting this OID will return the current Phase Alarm.
1.3.6.1.4.1.3808.1.1.3.2.2.1.1.5INTEGER {noLoadAlarm(1), underCurrentAlarm(2), nearOverCurrentAlarm(3), overCurrentAlarm(4)}read-onlymandatory
ePDULoadStatus
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.2.3
ePDULoadStatusTable
OBJECT-TYPE
Allows for getting of status of each Rack PDU phase/bank. The number of entries is calculated by adding the number of phases (ePDULoadDevNumPhases OID) and the number of banks of outlets (ePDULoadDevNumBanks) Number of entries = #phases + #banks. NOTE: If a device has phase and bank information, all phase information shall precede the bank information.
1.3.6.1.4.1.3808.1.1.3.2.3.1not-accessiblemandatory
ePDULoadStatusEntry
OBJECT-TYPE
The Rack PDU phase/bank to gather status from.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1not-accessiblemandatory
ePDULoadStatusIndex
OBJECT-TYPE
The index to the Rack PDU phase/bank entry. All phase information will precede any bank information
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.1INTEGER (1..10)read-onlymandatory
ePDULoadStatusLoad
OBJECT-TYPE
Getting this OID will return the phase/bank load measured in tenths of Amps.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.2Gaugeread-onlymandatory
ePDULoadStatusLoadState
OBJECT-TYPE
Getting this OID will return the phase/bank load state. loadNormal(1) indicates that the phase/bank is operating properly within the ePDULoadConfigLowLoadThreshold and ePDULoadConfigNearOverloadThreshold OID values. loadLow(2) indicates that the phase/bank load has dropped below the ePDULoadConfigLowLoadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. loadNearOverload(3) indicates that the phase/bank load is greater than or equal to the ePDULoadConfigNearOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. loadOverload(4) indicates that the phase/bank load is greater than or equal to the ePDULoadConfigOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.3INTEGER {loadNormal(1), loadLow(2), loadNearOverload(3), loadOverload(4)}read-onlymandatory
ePDULoadStatusPhaseNumber
OBJECT-TYPE
The phase number to which this record refers.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.4INTEGERread-onlymandatory
ePDULoadStatusBankNumber
OBJECT-TYPE
The bank number to which this record refers. A value of 0 will be returned if any bank is not present or if it is phase related.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.5INTEGERread-onlymandatory
ePDULoadStatusVoltage
OBJECT-TYPE
Getting this OID will return the phase/bank voltage measured in 0.1 volts.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.6INTEGERread-onlymandatory
ePDULoadStatusActivePower
OBJECT-TYPE
Getting this OID will return the phase/bank active power measured in watts.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.7INTEGERread-onlymandatory
ePDULoadStatusApparentPower
OBJECT-TYPE
Getting this OID will return the phase/bank apparent power measured in VA.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.8INTEGERread-onlymandatory
ePDULoadStatusPowerFactor
OBJECT-TYPE
Getting this OID will return power factor of the output measured in hundredths. A value of 100 representing a unity power factor (1.00).
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.9INTEGERread-onlymandatory
ePDULoadStatusEnergy
OBJECT-TYPE
Getting this OID will return the phase/bank apparent power measured in 0.1 kilowatt-hours.
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.10INTEGERread-onlymandatory
ePDULoadStatusEnergyStartTime
OBJECT-TYPE
Getting this OID will return the date and time of the last energy meter reset
1.3.6.1.4.1.3808.1.1.3.2.3.1.1.11DisplayStringread-onlymandatory
ePDULoadBankConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.2.4
ePDULoadBankConfigTable
OBJECT-TYPE
Allows for configuration of each Rack PDU bank. The number of entries is contained in the ePDULoadDevNumBanks OID.
1.3.6.1.4.1.3808.1.1.3.2.4.1not-accessiblemandatory
ePDULoadBankConfigEntry
OBJECT-TYPE
The Rack PDU bank to configure.
1.3.6.1.4.1.3808.1.1.3.2.4.1.1not-accessiblemandatory
ePDULoadBankConfigIndex
OBJECT-TYPE
The index to the Rack PDU bank entry.
1.3.6.1.4.1.3808.1.1.3.2.4.1.1.1INTEGER (1..10)read-onlymandatory
ePDULoadBankConfigLowLoadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in Amps. A warning will be issued when the load is less than the threshold value. A threshold value of 0 Amps effectively disables this warning. Maximum value must be less than the value returned by the ePDULoadBankConfigNearOverloadThreshold OID.
1.3.6.1.4.1.3808.1.1.3.2.4.1.1.2INTEGERread-writemandatory
ePDULoadBankConfigNearOverloadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than the value returned by the ePDULoadBankConfigLowLoadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadBankConfigOverloadThreshold OID.
1.3.6.1.4.1.3808.1.1.3.2.4.1.1.3INTEGERread-writemandatory
ePDULoadBankConfigOverloadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than or equal to the value returned by the ePDULoadBankConfigNearOverloadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadDevMaxBankLoad OID.
1.3.6.1.4.1.3808.1.1.3.2.4.1.1.4INTEGERread-writemandatory
ePDULoadBankConfigAlarm
OBJECT-TYPE
Getting this OID will return the current Bank Alarm.
1.3.6.1.4.1.3808.1.1.3.2.4.1.1.5INTEGER {noLoadAlarm(1), underCurrentAlarm(2), nearOverCurrentAlarm(3), overCurrentAlarm(4)}read-onlymandatory
ePDUOutlet
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.3
ePDUOutletDevice
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.3.1
ePDUOutletDevCommand
OBJECT-TYPE
Setting this OID to immediateAllOn (2) will turn all outlets on immediately. Setting this OID to immediateAllOff (3) will turn all outlets off immediately. Setting this OID to immediateAllReboot (4) will reboot all outlets immediately. Setting this OID to delayedAllOn (5) will turn all outlets on as defined by each outlet's ePDUOutletConfigPowerOnTime OID value. Setting this OID to delayedAllOff (6) will turn all outlets off as defined by each outlet's ePDUOutletConfigPowerOffTime OID value. Setting this OID to delayedAllReboot (7) will cause a delayedAllOff command to be performed. Once all outlets are off, the Switched Rack PDU will then delay the largest ePDUOutletConfigRebootDuration OID time, and then perform a delayedAllOn command. Setting this OID to cancelAllPendingCommands (8) will cause all pending commands on the Switched Rack PDU to be canceled. Getting this OID will return the noCommandAll (1) value.
1.3.6.1.4.1.3808.1.1.3.3.1.1INTEGER {noCommandAll(1), immediateAllOn(2), immediateAllOff(3), immediateAllReboot(4), delayedAllOn(5), delayedAllOff(6), delayedAllReboot(7), cancelAllPendingCommands(8)}read-writemandatory
ePDUOutletDevColdstartDelay
OBJECT-TYPE
The amount of delay, in seconds, between when power is provided to the Switched Rack PDU and when the Switched Rack PDU provides basic master power to the outlets. Allowed values are: -1 - never apply power automatically. 0 - apply power immediately. 1 to 300 - delay up to 300 seconds (5 minutes).
1.3.6.1.4.1.3808.1.1.3.3.1.2INTEGERread-writemandatory
ePDUOutletDevNumCntrlOutlets
OBJECT-TYPE
The number of controlled outlets on this Switched Rack PDU.
1.3.6.1.4.1.3808.1.1.3.3.1.3INTEGERread-onlymandatory
ePDUOutletDevNumTotalOutlets
OBJECT-TYPE
The total number of outlets on this Rack PDU.
1.3.6.1.4.1.3808.1.1.3.3.1.4INTEGERread-onlymandatory
ePDUOutletDevMonitoredOutlets
OBJECT-TYPE
The total number of monitored outlets on this Rack PDU.
1.3.6.1.4.1.3808.1.1.3.3.1.5INTEGERread-onlymandatory
ePDUOutletDevColdstartState
OBJECT-TYPE
The ePDU outlet state after coldstart. Allowed values are: 1 - all outlets on after coldstart. 2 - outlet status same as previous state.
1.3.6.1.4.1.3808.1.1.3.3.1.6INTEGER {allOn(1), previous(2)}read-writemandatory
ePDUOutletPhase
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.3.2
ePDUOutletPhaseTable
OBJECT-TYPE
Allows for management of outlets on a per phase basis.
1.3.6.1.4.1.3808.1.1.3.3.2.1not-accessiblemandatory
ePDUOutletPhaseEntry
OBJECT-TYPE
The phase to manage.
1.3.6.1.4.1.3808.1.1.3.3.2.1.1not-accessiblemandatory
ePDUOutletPhaseIndex
OBJECT-TYPE
The index to the Switched Rack PDU phase entry.
1.3.6.1.4.1.3808.1.1.3.3.2.1.1.1INTEGER {phase1(1), phase2(2), phase3(3)}read-onlymandatory
ePDUOutletPhaseOverloadRestriction
OBJECT-TYPE
This OID controls the behavior of a Switched Rack PDU phase when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding phase to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigOverloadThreshold OID is exceeded.
1.3.6.1.4.1.3808.1.1.3.3.2.1.1.2INTEGER {alwaysAllowTurnON(1), restrictOnNearOverload(2), restrictOnOverload(3)}read-writemandatory
ePDUOutletControl
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.3.3
ePDUOutletControlTable
OBJECT-TYPE
Allows for control of the individual outlets. The number of entries is contained in the ePDUOutletDevNumCntrlOutlets OID.
1.3.6.1.4.1.3808.1.1.3.3.3.1not-accessiblemandatory
ePDUOutletControlEntry
OBJECT-TYPE
The outlet to control.
1.3.6.1.4.1.3808.1.1.3.3.3.1.1not-accessiblemandatory
ePDUOutletControlIndex
OBJECT-TYPE
The index to the outlet entry.
1.3.6.1.4.1.3808.1.1.3.3.3.1.1.1INTEGER (1..24)read-onlymandatory
ePDUOutletControlOutletName
OBJECT-TYPE
The name of the outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size. This OID is provided for informational purposes only.
1.3.6.1.4.1.3808.1.1.3.3.3.1.1.2DisplayStringread-onlymandatory
ePDUOutletControlOutletPhase
OBJECT-TYPE
The phase/s associated with this outlet. For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), or phase3 (3) for outlets tied to a single phase. For outlets tied to two phases, this object will return phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
1.3.6.1.4.1.3808.1.1.3.3.3.1.1.3INTEGER {phase1(1), phase2(2), phase3(3), phase1-2(4), phase2-3(5), phase3-1(6)}read-onlymandatory
ePDUOutletControlOutletCommand
OBJECT-TYPE
Getting this variable will return the outlet state. If the outlet is on, the immediateOn (1) value will be returned. If the outlet is off, the immediateOff (2) value will be returned. Setting this variable to immediateOn (1) will immediately turn the outlet on. Setting this variable to immediateOff (2) will immediately turn the outlet off. Setting this variable to immediateReboot (3) will immediately reboot the outlet. Setting this variable to delayedOn (4) will turn the outlet on after the ePDUOutletConfigPowerOnTime OID time has elapsed. Setting this variable to delayedOff (5) will turn the outlet off after the ePDUOutletConfigPowerOffTime OID time has elapsed. Setting this variable to delayedReboot (6) will cause the Switched Rack PDU to perform a delayedOff command, wait the ePDUOutletConfigRebootDuration OID time, and then perform a delayedOn command. Setting this variable to cancelPendingCommand (7) will cause any pending command to this outlet to be canceled. Setting this variable to outletIdentify (8) will cause PDU LED to display the number of the outlet.
1.3.6.1.4.1.3808.1.1.3.3.3.1.1.4INTEGER {immediateOn(1), immediateOff(2), immediateReboot(3), delayedOn(4), delayedOff(5), delayedReboot(6), cancelPendingCommand(7), outletIdentify(8)}read-writemandatory
ePDUOutletControlOutletBank
OBJECT-TYPE
The bank associated with this outlet.
1.3.6.1.4.1.3808.1.1.3.3.3.1.1.5INTEGERread-onlymandatory
ePDUOutletConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.3.4
ePDUOutletConfigTable
OBJECT-TYPE
Allows for configuration of individual outlets. The number of entries is contained in the ePDUOutletDevNumCntrlOutlets OID.
1.3.6.1.4.1.3808.1.1.3.3.4.1not-accessiblemandatory
ePDUOutletConfigEntry
OBJECT-TYPE
The outlet to configure.
1.3.6.1.4.1.3808.1.1.3.3.4.1.1not-accessiblemandatory
ePDUOutletConfigIndex
OBJECT-TYPE
The index to the outlet entry.
1.3.6.1.4.1.3808.1.1.3.3.4.1.1.1INTEGER (1..24)read-onlymandatory
ePDUOutletConfigOutletName
OBJECT-TYPE
The name of the outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size.
1.3.6.1.4.1.3808.1.1.3.3.4.1.1.2DisplayStringread-writemandatory
ePDUOutletConfigOutletPhase
OBJECT-TYPE
The phase/s associated with this outlet. For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), or phase3 (3) for outlets tied to a single phase. For outlets tied to two phases, this object will return phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
1.3.6.1.4.1.3808.1.1.3.3.4.1.1.3INTEGER {phase1(1), phase2(2), phase3(3), phase1-2(4), phase2-3(5), phase3-1(6)}read-onlymandatory
ePDUOutletConfigPowerOnTime
OBJECT-TYPE
The amount of time (in seconds) the outlet will delay powering on at coldstart or when a command that requires a turn-on delay is issued. Allowed values are: -1 - never power on. 0 - power on immediately. 1 to 7200 - power on up to 7200 seconds after being commanded.
1.3.6.1.4.1.3808.1.1.3.3.4.1.1.4INTEGERread-writemandatory
ePDUOutletConfigPowerOffTime
OBJECT-TYPE
The amount of time (in seconds) the outlet will delay powering off when a command that requires a turn-off delay is issued. Allowed values are: -1 - never power off. 0 - power off immediately. 1 to 7200 - power off up to 7200 seconds after being commanded.
1.3.6.1.4.1.3808.1.1.3.3.4.1.1.5INTEGERread-writemandatory
ePDUOutletConfigRebootDuration
OBJECT-TYPE
During a reboot sequence, power is turned off and then back on. This OID defines the amount of time to wait, in seconds, after turning the power off, at the start of the sequence, before turning power back on, at the end of the reboot sequence. Allowed range is any value between 5 and 60 seconds (1 minute).
1.3.6.1.4.1.3808.1.1.3.3.4.1.1.6INTEGERread-writemandatory
ePDUOutletConfigOutletBank
OBJECT-TYPE
The bank associated with this outlet.
1.3.6.1.4.1.3808.1.1.3.3.4.1.1.7INTEGERread-onlymandatory
ePDUOutletConfigMonitoredTableSize
OBJECT-TYPE
The size of the Outlet Config Monitored Table
1.3.6.1.4.1.3808.1.1.3.3.4.2INTEGERread-onlymandatory
ePDUOutletConfigMonitoredTable
OBJECT-TYPE
Allows for getting/setting of outlet thresholds of an Outlet Monitored Rack PDU.
1.3.6.1.4.1.3808.1.1.3.3.4.3not-accessiblemandatory
ePDUOutletConfigMonitoredEntry
OBJECT-TYPE
This gives access to Monitored Outlet entries
1.3.6.1.4.1.3808.1.1.3.3.4.3.1not-accessiblemandatory
ePDUOutletConfigMonitoredIndex
OBJECT-TYPE
The index to the RACK PDU Phase entry.
1.3.6.1.4.1.3808.1.1.3.3.4.3.1.1INTEGER (1..24)read-onlymandatory
ePDUOutletConfigMonitoredName
OBJECT-TYPE
The name of the Monitored Outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size.
1.3.6.1.4.1.3808.1.1.3.3.4.3.1.2DisplayStringread-writemandatory
ePDUOutletConfigMonitoredNumber
OBJECT-TYPE
The outlet number of an Outlet Monitored RACK PDU.
1.3.6.1.4.1.3808.1.1.3.3.4.3.1.3INTEGERread-onlymandatory
ePDUOutletConfigMonitoredLowLoadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in watts. A warning will be issued when the load is less than the threshold value. A threshold value of 0 effectively disables this warning. Maximum value must be less than the value returned by the ePDUOutletConfigMonitoredNearOverloadThreshold OID. 0 will be returned if the unit is not Outlet Monitored Rack PDU.
1.3.6.1.4.1.3808.1.1.3.3.4.3.1.4INTEGERread-writemandatory
ePDUOutletConfigMonitoredNearOverloadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in watts. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than the value returned by the ePDUOutletConfigMonitoredLowLoadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDUOutletConfigMonitoredOverloadThreshold OID. 0 will be returned if the unit is not Outlet Monitored Rack PDU.
1.3.6.1.4.1.3808.1.1.3.3.4.3.1.5INTEGERread-writemandatory
ePDUOutletConfigMonitoredOverloadThreshold
OBJECT-TYPE
A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in watts. A warning will be issued when the load is greater than or equal to the threshold value. Minimum value must be greater than or equal to the value returned by the ePDUOutletConfigMonitoredNearOverloadThreshold OID. Maximum value must be less than or equal to the value returned by the ePDULoadDevMaxOutletLoad OID. 0 will be returned if the unit is not Outlet Monitored Rack PDU.
1.3.6.1.4.1.3808.1.1.3.3.4.3.1.6INTEGERread-writemandatory
ePDUOutletConfigMonitoredPeakLoadReset
OBJECT-TYPE
Setting this OID to reset (2) will cause the existing peak power value to be replaced by the current load power value. Getting this oid will do nothing and return noAction (1) if the PDU support this feature, return notSupport (3) if the PDU do not support this feature.
1.3.6.1.4.1.3808.1.1.3.3.4.3.1.7INTEGER {noAction(1), reset(2), notSupport(3)}read-writemandatory
ePDUOutletConfigMonitoredEnergyReset
OBJECT-TYPE
Setting this OID to reset (2) will cause the device energy meter value to be reset to zero. Getting this oid will do nothing and return noAction (1) if the PDU support this feature, return notSupport (3) if the PDU do not support this feature.
1.3.6.1.4.1.3808.1.1.3.3.4.3.1.8INTEGER {noAction(1), reset(2), notSupport(3)}read-writemandatory
ePDUOutletStatus
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.3.5
ePDUOutletStatusTable
OBJECT-TYPE
Allows for getting of status of individual outlets. The number of entries is contained in the ePDUOutletDevNumCntrlOutlets OID.
1.3.6.1.4.1.3808.1.1.3.3.5.1not-accessiblemandatory
ePDUOutletStatusEntry
OBJECT-TYPE
The outlet to gather status from.
1.3.6.1.4.1.3808.1.1.3.3.5.1.1not-accessiblemandatory
ePDUOutletStatusIndex
OBJECT-TYPE
The index to the outlet entry.
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.1INTEGER (1..24)read-onlymandatory
ePDUOutletStatusOutletName
OBJECT-TYPE
The name of the outlet. The maximum string size is device dependent. This OID is provided for informational purposes only.
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.2DisplayStringread-onlymandatory
ePDUOutletStatusOutletPhase
OBJECT-TYPE
The phase/s associated with this outlet. For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), or phase3 (3) for outlets tied to a single phase. For outlets tied to two phases, this object will return phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.3INTEGER {phase1(1), phase2(2), phase3(3), phase1-2(4), phase2-3(5), phase3-1(6)}read-onlymandatory
ePDUOutletStatusOutletState
OBJECT-TYPE
Getting this variable will return the outlet state. If the outlet is on, the outletStatusOn (1) value will be returned. If the outlet is off, the outletStatusOff (2) value will be returned.
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.4INTEGER {outletStatusOn(1), outletStatusOff(2)}read-onlymandatory
ePDUOutletStatusCommandPending
OBJECT-TYPE
Getting this variable will return the command pending state of the outlet. If a command is pending on the outlet, the outletStatusCommandPending (1) value will be returned. If there is not a command pending on the outlet, the outletStatusNoCommandPending (2) will be returned.
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.5INTEGER {outletStatusCommandPending(1), outletStatusNoCommandPending(2)}read-onlymandatory
ePDUOutletStatusOutletBank
OBJECT-TYPE
The bank associated with this outlet.
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.6INTEGERread-onlymandatory
ePDUOutletStatusLoad
OBJECT-TYPE
Getting this OID will return the measured Outlet load for an Outlet Monitored Rack PDU in tenths of Amps.
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.7Gaugeread-onlymandatory
ePDUOutletStatusActivePower
OBJECT-TYPE
Getting this OID will return the measured Outlet load for an Outlet Monitored Rack PDU in watts
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.8Gaugeread-onlymandatory
ePDUOutletStatusAlarm
OBJECT-TYPE
Getting this OID will return the current outlet alarm
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.9INTEGER {noLoadAlarm(1), underCurrentAlarm(2), nearOverCurrentAlarm(3), overCurrentAlarm(4)}read-onlymandatory
ePDUOutletStatusPeakPower
OBJECT-TYPE
The peak power consumption of the Rack PDU load in watts. This value can be reset by setting the oid ePDUOutletConfigMonitoredPeakLoadReset to reset (2)
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.10Gaugeread-onlymandatory
ePDUOutletStatusPeakPowerTime
OBJECT-TYPE
Get this oid shows the date and time that peak power consumption occurred
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.11DisplayStringread-onlymandatory
ePDUOutletStatusPeakPowerStart
OBJECT-TYPE
Get this oid shows the date and time that peak power consumption started
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.12DisplayStringread-onlymandatory
ePDUOutletStatusEnergy
OBJECT-TYPE
Energy meter measuring Rack PDU load energy consumption in tenths of kilowatt-hours. This value can be reset by setting the oid ePDUOutletConfigMonitoredEnergyReset to reset (2)
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.13Gaugeread-onlymandatory
ePDUOutletStatusEnergyStartTime
OBJECT-TYPE
Indicates the date and time of the last device energy meter reset
1.3.6.1.4.1.3808.1.1.3.3.5.1.1.14DisplayStringread-onlymandatory
ePDUOutletBank
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.3.6
ePDUOutletBankTable
OBJECT-TYPE
Allows for management of outlets on a per bank basis.
1.3.6.1.4.1.3808.1.1.3.3.6.1not-accessiblemandatory
ePDUOutletBankEntry
OBJECT-TYPE
The bank to manage.
1.3.6.1.4.1.3808.1.1.3.3.6.1.1not-accessiblemandatory
ePDUOutletBankIndex
OBJECT-TYPE
The index to the Switched Rack PDU bank entry.
1.3.6.1.4.1.3808.1.1.3.3.6.1.1.1INTEGER (1..10)read-onlymandatory
ePDUOutletBankOverloadRestriction
OBJECT-TYPE
This OID controls the behavior of a Switched Rack PDU bank when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding bank to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding bank to turn on if the ePDULoadBankConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding bank to turn on if the ePDULoadBankConfigOverloadThreshold OID is exceeded.
1.3.6.1.4.1.3808.1.1.3.3.6.1.1.2INTEGER {alwaysAllowTurnON(1), restrictOnNearOverload(2), restrictOnOverload(3)}read-writemandatory
ePDUPowerSupply
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.4
ePDUPowerSupplyDevice
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.4.1
ePDUPowerSupply1Status
OBJECT-TYPE
Getting this OID will return powerSupply1Ok(1) if power supply 1 is functioning normally. If not functioning normally, this OID will return powerSupply1Failed(2).
1.3.6.1.4.1.3808.1.1.3.4.1.1INTEGER {powerSupplyOneOk(1), powerSupplyOneFailed(2)}read-onlymandatory
ePDUPowerSupply2Status
OBJECT-TYPE
Getting this OID will return powerSupply2Ok(1) if power supply 2 is functioning normally. If not functioning normally, this OID will return powerSupply2Failed(2). Metered Rack PDUs do not have a redundant powersupply.
1.3.6.1.4.1.3808.1.1.3.4.1.2INTEGER {powerSupplyTwoOk(1), powerSupplyTwoFailed(2), powerSupplyTwoNotPresent(3)}read-onlymandatory
ePDUPowerSupplyAlarm
OBJECT-TYPE
Getting this OID will return powerSupply Alarm
1.3.6.1.4.1.3808.1.1.3.4.1.3INTEGER {allAvailablePowerSuppliesOK(1), powerSupplyOneFailed(2), powerSupplyTwoFailed(3), powerSupplyOneandTwoFailed(4)}read-onlymandatory
ePDUStatus
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.3.5
ePDUStatusBankTableSize
OBJECT-TYPE
The size of the Status Bank Table
1.3.6.1.4.1.3808.1.1.3.5.1INTEGERread-onlymandatory
ePDUStatusBankTable
OBJECT-TYPE
Allows for getting of status of each Rack PDU Bank
1.3.6.1.4.1.3808.1.1.3.5.2not-accessiblemandatory
ePDUStatusBankEntry
OBJECT-TYPE
This gives access to Bank entries
1.3.6.1.4.1.3808.1.1.3.5.2.1not-accessiblemandatory
ePDUStatusBankIndex
OBJECT-TYPE
The index to the RACK PDU Bank entry.
1.3.6.1.4.1.3808.1.1.3.5.2.1.1INTEGER (1..10)read-onlymandatory
ePDUStatusBankNumber
OBJECT-TYPE
Getting this OID will return the bank number.
1.3.6.1.4.1.3808.1.1.3.5.2.1.2INTEGERread-onlymandatory
ePDUStatusBankState
OBJECT-TYPE
Getting this OID will return the bank load state. bankLoadNormal(1) indicates that the bank is operating properly within the ePDULoadBankConfigLowLoadThreshold and ePDULoadBankConfigNearOverloadThreshold OID values. bankLoadLow(2) indicates that the bank load has dropped below the ePDULoadBankConfigLowLoadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. bankLoadNearOverload(3) indicates that the bank load is greater than or equal to the ePDULoadBankConfigNearOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. bankLoadOverload(4) indicates that the bank load is greater than or equal to the ePDULoadBankConfigOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared.
1.3.6.1.4.1.3808.1.1.3.5.2.1.3INTEGER {bankLoadNormal(1), bankLoadLow(2), bankLoadNearOverload(3), bankLoadOverload(4)}read-onlymandatory
ePDUStatusPhaseTableSize
OBJECT-TYPE
The size of the Status Phase Table
1.3.6.1.4.1.3808.1.1.3.5.3INTEGERread-onlymandatory
ePDUStatusPhaseTable
OBJECT-TYPE
Allows for getting of status of each Rack PDU Phase
1.3.6.1.4.1.3808.1.1.3.5.4not-accessiblemandatory
ePDUStatusPhaseEntry
OBJECT-TYPE
This gives access to Phase entries
1.3.6.1.4.1.3808.1.1.3.5.4.1not-accessiblemandatory
ePDUStatusPhaseIndex
OBJECT-TYPE
The index to the RACK PDU Phase entry.
1.3.6.1.4.1.3808.1.1.3.5.4.1.1INTEGER (1..10)read-onlymandatory
ePDUStatusPhaseNumber
OBJECT-TYPE
Getting this OID will return the phase number.
1.3.6.1.4.1.3808.1.1.3.5.4.1.2INTEGERread-onlymandatory
ePDUStatusPhaseState
OBJECT-TYPE
Getting this OID will return the Phase load state. phaseLoadNormal(1) indicates that the Phase is operating properly within the ePDULoadPhaseConfigLowLoadThreshold and ePDULoadPhaseConfigNearOverloadThreshold OID values. phaseLoadLow(2) indicates that the Phase load has dropped below the ePDULoadPhaseConfigLowLoadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. phaseLoadNearOverload(3) indicates that the Phase load is greater than or equal to the ePDULoadPhaseConfigNearOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. phaseLoadOverload(4) indicates that the Phase load is greater than or equal to the ePDULoadPhaseConfigOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared.
1.3.6.1.4.1.3808.1.1.3.5.4.1.3INTEGER {phaseLoadNormal(1), phaseLoadLow(2), phaseLoadNearOverload(3), phaseLoadOverload(4)}read-onlymandatory
ePDUStatusOutletTableSize
OBJECT-TYPE
The size of the Status Outlet Table
1.3.6.1.4.1.3808.1.1.3.5.5INTEGERread-onlymandatory
ePDUStatusOutletTable
OBJECT-TYPE
Allows for getting of status of each Outlet of an Outlet Monitored Rack PDU.
1.3.6.1.4.1.3808.1.1.3.5.6not-accessiblemandatory
ePDUStatusOutletEntry
OBJECT-TYPE
This gives access to Outlet entries
1.3.6.1.4.1.3808.1.1.3.5.6.1not-accessiblemandatory
ePDUStatusOutletIndex
OBJECT-TYPE
The index to the RACK PDU Outlet entry.
1.3.6.1.4.1.3808.1.1.3.5.6.1.1INTEGER (1..24)read-onlymandatory
ePDUStatusOutletNumber
OBJECT-TYPE
Getting this OID will return the Outlet number.
1.3.6.1.4.1.3808.1.1.3.5.6.1.2INTEGERread-onlymandatory
ePDUStatusOutletState
OBJECT-TYPE
Getting this OID will return the Outlet load state. outletLoadNormal(1) indicates that the Outlet is operating properly within the ePDUOutletConfigMonitoredLowLoadThreshold and ePDUOutletConfigMonitoredNearOverloadThreshold OID values. outletLoadLow(2) indicates that the Outlet load has dropped below the ePDUOutletConfigMonitoredLowLoadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. outletLoadNearOverload(3) indicates that the Outlet load is greater than or equal to the ePDUOutletConfigMonitoredNearOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared. outletLoadOverload(4) indicates that the Outlet load is greater than or equal to the ePDUOutletConfigMonitoredOverloadThreshold OID value. An SNMP trap will occur when this state is entered or cleared.
1.3.6.1.4.1.3808.1.1.3.5.6.1.3INTEGER {outletLoadNormal(1), outletLoadLow(2), outletLoadNearOverload(3), outletLoadOverload(4)}read-onlymandatory
ePDUStatusInputVoltage
OBJECT-TYPE
The input voltage in 0.1 Volt.
1.3.6.1.4.1.3808.1.1.3.5.7INTEGERread-onlymandatory
ePDUStatusInputFrequency
OBJECT-TYPE
The input frequency in 0.1 Hertz.
1.3.6.1.4.1.3808.1.1.3.5.8INTEGERread-onlymandatory
environmentSensor
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.4
envirIdent
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.4.1
envirIdentName
OBJECT-TYPE
The name of the environment sensor. The maximum string size is device dependent.
1.3.6.1.4.1.3808.1.1.4.1.1DisplayStringread-writemandatory
envirIdentLocation
OBJECT-TYPE
The location of the environment sensor. The maximum string size is device dependent.
1.3.6.1.4.1.3808.1.1.4.1.2DisplayStringread-writemandatory
envirTemp
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.4.2
envirTemperature
OBJECT-TYPE
The environment temperature expressed in 1/10 Fahrenheit
1.3.6.1.4.1.3808.1.1.4.2.1INTEGERread-onlymandatory
envirTempHighThreshold
OBJECT-TYPE
The high temperature threshold of the environment sensor. The value expressed in Fahrenheit.
1.3.6.1.4.1.3808.1.1.4.2.2INTEGERread-writemandatory
envirTempLowThreshold
OBJECT-TYPE
The low temperature threshold of the environment sensor. The value expressed in Fahrenheit.
1.3.6.1.4.1.3808.1.1.4.2.3INTEGERread-writemandatory
envirTempRateOfChange
OBJECT-TYPE
The rate of change of the temperature. The value expressed in Fahrenheit per 5 minute.
1.3.6.1.4.1.3808.1.1.4.2.4INTEGERread-writemandatory
envirTempHysteresis
OBJECT-TYPE
The number of degrees beyond the temperature thresholds at which an active temperature alarm will be cleared. This configuration setting applies to all temperature thresholds. Units are displayed in Fahrenheit.
1.3.6.1.4.1.3808.1.1.4.2.5INTEGERread-writemandatory
envirTemperatureCelsius
OBJECT-TYPE
The environment temperature expressed in 1/10 Celsius
1.3.6.1.4.1.3808.1.1.4.2.6INTEGERread-onlymandatory
envirTempCelsiusHighThreshold
OBJECT-TYPE
The high temperature threshold of the environment sensor. The value expressed in Celsius.
1.3.6.1.4.1.3808.1.1.4.2.7INTEGERread-writemandatory
envirTempCelsiusLowThreshold
OBJECT-TYPE
The low temperature threshold of the environment sensor. The value expressed in Celsius.
1.3.6.1.4.1.3808.1.1.4.2.8INTEGERread-writemandatory
envirTempCelsiusRateOfChange
OBJECT-TYPE
The rate of change of the temperature. The value expressed in Celsius per 5 minute.
1.3.6.1.4.1.3808.1.1.4.2.9INTEGERread-writemandatory
envirTempCelsiusHysteresis
OBJECT-TYPE
The number of degrees beyond the temperature thresholds at which an active temperature alarm will be cleared. This configuration setting applies to all temperature thresholds. Units are displayed in Celsius.
1.3.6.1.4.1.3808.1.1.4.2.10INTEGERread-writemandatory
envirHumid
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.4.3
envirHumidity
OBJECT-TYPE
The environment relative humidity expressed in persentage.
1.3.6.1.4.1.3808.1.1.4.3.1INTEGERread-onlymandatory
envirHumidHighThreshold
OBJECT-TYPE
The high relative humidity threshold of the environment sensor. The value expressed in persentage.
1.3.6.1.4.1.3808.1.1.4.3.2INTEGERread-writemandatory
envirHumidLowThreshold
OBJECT-TYPE
The low relative humidity threshold of the environment sensor. The value expressed in persentage.
1.3.6.1.4.1.3808.1.1.4.3.3INTEGERread-writemandatory
envirHumidRateOfChange
OBJECT-TYPE
The rate of change of the relative humidity. The value expressed in persentage per 5 minute.
1.3.6.1.4.1.3808.1.1.4.3.4INTEGERread-writemandatory
envirHumidHysteresis
OBJECT-TYPE
The number of degrees beyond the relative humidity thresholds at which an active relative humidity alarm will be cleared. This configuration setting applies to all relative humidity thresholds. Units are displayed in persentage.
1.3.6.1.4.1.3808.1.1.4.3.5INTEGERread-writemandatory
envirContact
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.4.4
envirContactTableSize
OBJECT-TYPE
The number of the contact in the environment sensor.
1.3.6.1.4.1.3808.1.1.4.4.1INTEGERread-onlymandatory
envirContactTable
OBJECT-TYPE
Allows for getting of information of each contact of the environment sensor.
1.3.6.1.4.1.3808.1.1.4.4.2not-accessiblemandatory
envirContactEntry
OBJECT-TYPE
This gives access to contact entries
1.3.6.1.4.1.3808.1.1.4.4.2.1not-accessiblemandatory
envirContactIndex
OBJECT-TYPE
The index to the contact of the environment sensor.
1.3.6.1.4.1.3808.1.1.4.4.2.1.1INTEGER (1..4)read-onlymandatory
envirContactName
OBJECT-TYPE
Getting or setting the name of the contact of the environment sensor.
1.3.6.1.4.1.3808.1.1.4.4.2.1.2DisplayStringread-writemandatory
envirContactStatus
OBJECT-TYPE
Getting this OID will return the Contact Status.
1.3.6.1.4.1.3808.1.1.4.4.2.1.3INTEGER {contactNormal(1), contactAbnormal(2)}read-onlymandatory
envirContactNormalState
OBJECT-TYPE
Set the contact normal state.
1.3.6.1.4.1.3808.1.1.4.4.2.1.4INTEGER {normalOpen(1), normalClose(2)}read-writemandatory
ats
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5
atsIdent
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.1
atsIdentName
OBJECT-TYPE
The name of the ATS. The maximum string size is device dependent.
1.3.6.1.4.1.3808.1.1.5.1.1DisplayStringread-writemandatory
atsIdentModelName
OBJECT-TYPE
A string identifying the model name of the Automatic Transfer Switch. This value is set at the factory.
1.3.6.1.4.1.3808.1.1.5.1.2DisplayStringread-onlymandatory
atsIdentHardwareRev
OBJECT-TYPE
The hardware revision of the Automatic Transfer Switch. This value is set at the factory.
1.3.6.1.4.1.3808.1.1.5.1.3DisplayStringread-onlymandatory
atsIdentFirmwareRev
OBJECT-TYPE
A string identifying the Automatic Transfer Switch firmware revision.
1.3.6.1.4.1.3808.1.1.5.1.4DisplayStringread-onlymandatory
atsIdentSerialNumber
OBJECT-TYPE
A string identifying the serial number of the Automatic Transfer Switch. This value is set at the factory.
1.3.6.1.4.1.3808.1.1.5.1.5DisplayStringread-onlymandatory
atsIdentDateOfManufacture
OBJECT-TYPE
The date when the Automatic Transfer Switch was manufactured in mm/dd/yyyy format. This value is set at the factory.
1.3.6.1.4.1.3808.1.1.5.1.6DisplayStringread-onlymandatory
atsIdentDeviceRatingVoltage
OBJECT-TYPE
A string identifing the Automatic Transfer Switch rating voltage.
1.3.6.1.4.1.3808.1.1.5.1.7DisplayStringread-onlymandatory
atsIdentDeviceRatingCurrent
OBJECT-TYPE
This gives the device rating current in Amps
1.3.6.1.4.1.3808.1.1.5.1.8INTEGERread-onlymandatory
atsIdentDeviceOutletNum
OBJECT-TYPE
This gives the outlet number of the device
1.3.6.1.4.1.3808.1.1.5.1.9INTEGERread-onlymandatory
atsIdentAgentModelName
OBJECT-TYPE
A string identifying the model name of the Agent.
1.3.6.1.4.1.3808.1.1.5.1.10DisplayStringread-onlymandatory
atsIdentAgentHardwareRevision
OBJECT-TYPE
The hardware revision of the Agent.
1.3.6.1.4.1.3808.1.1.5.1.11DisplayStringread-onlymandatory
atsIdentAgentFirmwareRevision
OBJECT-TYPE
A string identifying the Agent firmware revision.
1.3.6.1.4.1.3808.1.1.5.1.12DisplayStringread-onlymandatory
atsIdentAgentSerialNumber
OBJECT-TYPE
A string identifying the serial number of the Agent.
1.3.6.1.4.1.3808.1.1.5.1.13DisplayStringread-onlymandatory
atsStatus
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.2
atsStatusDevice
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.2.1
atsStatusCommStatus
OBJECT-TYPE
This variable returns the current communication status between the Automatic Transfer Switch and the Agent.
1.3.6.1.4.1.3808.1.1.5.2.1.1INTEGER {atsNeverDiscovered(1), atsCommEstablished(2), atsCommLost(3)}read-onlymandatory
atsStatusSelectedSource
OBJECT-TYPE
This variable returns the current source of power.
1.3.6.1.4.1.3808.1.1.5.2.1.2INTEGER {sourceA(1), sourceB(2)}read-onlymandatory
atsStatusRedundancyState
OBJECT-TYPE
This variable returns the current redundancy state of the ATS. atsRedundancyLost(1) indicates that the ATS is unable to switch over to the alternate power source if the current source fails. atsFullyRedundant(2) indicates that the ATS will switch over to the alternate power source if the current source fails.
1.3.6.1.4.1.3808.1.1.5.2.1.3INTEGER {atsRedundancyLost(1), atsFullyRedundant(2)}read-onlymandatory
atsStatusPhaseSyncStatus
OBJECT-TYPE
This variable returns the status of the phase sync.
1.3.6.1.4.1.3808.1.1.5.2.1.4INTEGER {inSync(1), outOfSync(2)}read-onlymandatory
atsStatusDevSourceRelayStatus
OBJECT-TYPE
This variable returns the status of the source relay.
1.3.6.1.4.1.3808.1.1.5.2.1.5INTEGER {sourceRelayNormal(1), sourceRelayFail(2)}read-onlymandatory
atsStatusDevInRelayStatus
OBJECT-TYPE
This variable returns the status of the input relay.
1.3.6.1.4.1.3808.1.1.5.2.1.6INTEGER {inputRelayNormal(1), inputRelayFail(2)}read-onlymandatory
atsStatusDevOutRelayStatus
OBJECT-TYPE
This variable returns the status of the Output relay.
1.3.6.1.4.1.3808.1.1.5.2.1.7INTEGER {outputRelayNormal(1), outputRelayFail(2)}read-onlymandatory
atsStatusDevLCDCommStatus
OBJECT-TYPE
This variable returns the communication status of the LCD.
1.3.6.1.4.1.3808.1.1.5.2.1.8INTEGER {lcdCommNormal(1), lcdCommFail(2)}read-onlymandatory
atsStatusDevDB9CommStatus
OBJECT-TYPE
This variable returns the communication status of the DB9.
1.3.6.1.4.1.3808.1.1.5.2.1.9INTEGER {db9CommNormal(1), db9CommFail(2)}read-onlymandatory
atsStatusPowerSupplyTable
OBJECT-TYPE
A list of power supply table entries.
1.3.6.1.4.1.3808.1.1.5.2.1.10not-accessiblemandatory
atsStatusPowerSupplyEntry
OBJECT-TYPE
An entry containing power supply information applicable to a particular input.
1.3.6.1.4.1.3808.1.1.5.2.1.10.1not-accessiblemandatory
atsStatusPowerSupplyTableIndex
OBJECT-TYPE
The input identifier.
1.3.6.1.4.1.3808.1.1.5.2.1.10.1.1INTEGER (1..10)read-onlymandatory
atsStatusPowerSupplyInputSource
OBJECT-TYPE
The input source to the power supply.
1.3.6.1.4.1.3808.1.1.5.2.1.10.1.2INTEGER {sourceA(1), sourceB(2)}read-onlymandatory
atsStatusPowerSupply12VStatus
OBJECT-TYPE
This variable returns the status of the power supply A 12V in system.
1.3.6.1.4.1.3808.1.1.5.2.1.10.1.3INTEGER {powerSupplyOK(1), powerSupplyFailure(2)}read-onlymandatory
atsStatusPowerSupply5VStatus
OBJECT-TYPE
This variable returns the status of the power supply A 5V in system.
1.3.6.1.4.1.3808.1.1.5.2.1.10.1.4INTEGER {powerSupplyOK(1), powerSupplyFailure(2)}read-onlymandatory
atsStatusPowerSupply3p3VStatus
OBJECT-TYPE
This variable returns the status of the power supply A 3.3V in system.
1.3.6.1.4.1.3808.1.1.5.2.1.10.1.5INTEGER {powerSupplyOK(1), powerSupplyFailure(2)}read-onlymandatory
atsStatusInput
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.2.2
atsStatusInputNum
OBJECT-TYPE
The number of input feeds to this device. This variable indicates the number of rows in the status input table.
1.3.6.1.4.1.3808.1.1.5.2.2.1INTEGERread-onlymandatory
atsStatusInputTable
OBJECT-TYPE
A list of input table entries. The number of entries is given by the value of atsNumInputs.
1.3.6.1.4.1.3808.1.1.5.2.2.2not-accessiblemandatory
atsStatusInputEntry
OBJECT-TYPE
An entry containing information applicable to a particular input.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1not-accessiblemandatory
atsStatusInputTableIndex
OBJECT-TYPE
The input identifier.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1.1INTEGER (1..10)read-onlymandatory
atsStatusInputName
OBJECT-TYPE
A name given to a particular input.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1.2DisplayStringread-writemandatory
atsStatusNumInputPhase
OBJECT-TYPE
The number of input phases utilized in this device. The sum of all the atsStatusNumInputPhase variable indicates the number of rows in the status input phase table.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1.3INTEGERread-onlymandatory
atsStatusInputVoltageOrientation
OBJECT-TYPE
The input voltage orientation: 1: unknown for this Source 2: singlePhase - phase 1 voltage is between Phase 1 and Neutral. 3: splitPhase - phase 1 voltage is between Phase 1 and Neutral; phase 2 voltage is between Phase 2 and Neutral; phase 3 voltage is between Phase 1 and Phase 2. 4: threePhasePhaseToNeutral - phase 1 voltage is between Phase 1 and Neutral; phase 2 voltage is between Phase 2 and Neutral; phase 3 voltage is between Phase 3 and Neutral. 5: threePhasePhaseToPhase - phase 1 voltage is between Phase 1 and Phase 2; phase 2 voltage is between Phase 2 and Phase 3; phase 3 voltage is between Phase 3 and Phase 1.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1.4INTEGER {unknown(1), singlePhase(2), splitPhase(3), threePhasePhaseToNeutral(4), threePhasePhaseToPhase(5)}read-onlymandatory
atsStatusInputVoltage
OBJECT-TYPE
The input voltage in 0.1 Volt.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1.5INTEGERread-onlymandatory
atsStatusInputFrequency
OBJECT-TYPE
The input frequency in 0.1 Hertz.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1.6INTEGERread-onlymandatory
atsStatusInputVolState
OBJECT-TYPE
The input voltage status.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1.7INTEGER {normal(1), overVoltage(2), underVoltage(3)}read-onlymandatory
atsStatusInputFreqState
OBJECT-TYPE
The input frequency status.
1.3.6.1.4.1.3808.1.1.5.2.2.2.1.8INTEGER {normal(1), overFrequency(2), underFrequency(3)}read-onlymandatory
atsStatusInputPhaseTable
OBJECT-TYPE
A list of input table entries. The number of entries is given by the sum of the atsNumInputPhases.
1.3.6.1.4.1.3808.1.1.5.2.2.3not-accessiblemandatory
atsStatusInputPhaseEntry
OBJECT-TYPE
An entry containing information applicable to a particular input phase.
1.3.6.1.4.1.3808.1.1.5.2.2.3.1not-accessiblemandatory
atsStatusInputPhaseTableIndex
OBJECT-TYPE
The input identifier.
1.3.6.1.4.1.3808.1.1.5.2.2.3.1.1INTEGER (1..10)read-onlymandatory
atsStatusInputPhaseIndex
OBJECT-TYPE
The input phase identifier.
1.3.6.1.4.1.3808.1.1.5.2.2.3.1.2INTEGER (1..10)read-onlymandatory
atsStatusInputPhaseVoltage
OBJECT-TYPE
The input voltage in VAC, or -1 if it's unsupported by this Source.
1.3.6.1.4.1.3808.1.1.5.2.2.3.1.3INTEGERread-onlymandatory
atsStatusInputPhaseCurrent
OBJECT-TYPE
The input current in amperes, or -1 if it's unsupported by this Source.
1.3.6.1.4.1.3808.1.1.5.2.2.3.1.4INTEGERread-onlymandatory
atsStatusInputPhasePower
OBJECT-TYPE
The input power in Watts, or -1 if it's unsupported by this Source.
1.3.6.1.4.1.3808.1.1.5.2.2.3.1.5INTEGERread-onlymandatory
atsConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.3
atsConfigPreferredSource
OBJECT-TYPE
This variable returns the preferred source of power when both sources are OK.
1.3.6.1.4.1.3808.1.1.5.3.1INTEGER {sourceA(1), sourceB(2), none(3)}read-writemandatory
atsConfigNominalVoltage
OBJECT-TYPE
This variable returns the nominal voltage of the input.
1.3.6.1.4.1.3808.1.1.5.3.2INTEGERread-writemandatory
atsConfigVoltageSensitivity
OBJECT-TYPE
This variable defines the sensitivity to changes in voltage: high(1) for best protection, low(3) for frequent small line voltage changes.
1.3.6.1.4.1.3808.1.1.5.3.3INTEGER {high(1), medium(2), low(3)}read-writemandatory
atsConfigTransferVoltageRange
OBJECT-TYPE
This variable defines the range of acceptable voltage from a power source. If the voltage measured from the selected input source is not within this range, the Automatic Transfer Switch will switch over (transfer) to the alternate power source.
1.3.6.1.4.1.3808.1.1.5.3.4INTEGER {wide(1), medium(2), narrow(3)}read-writemandatory
atsConfigNarrowRangeValue
OBJECT-TYPE
To configure the Narrow Range value of acceptable voltage from a power source.
1.3.6.1.4.1.3808.1.1.5.3.5INTEGERread-writemandatory
atsConfigMediumRangeValue
OBJECT-TYPE
To configure the Medium Range value of acceptable voltage from a power source.
1.3.6.1.4.1.3808.1.1.5.3.6INTEGERread-writemandatory
atsConfigWideRangeValue
OBJECT-TYPE
To configure the Wide Range value of acceptable voltage from a power source.
1.3.6.1.4.1.3808.1.1.5.3.7INTEGERread-writemandatory
atsConfigFrequencyDeviation
OBJECT-TYPE
To configure the frequency deviation.
1.3.6.1.4.1.3808.1.1.5.3.8INTEGER (1..3)read-writemandatory
atsConfigDevLCDOffTime
OBJECT-TYPE
The amount of time (in seconds) which LCD turn off automatically after it remains idle for.
1.3.6.1.4.1.3808.1.1.5.3.9INTEGERread-writemandatory
atsControl
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.4
atsCtrlResetATS
OBJECT-TYPE
Setting this variable will cause the Automatic Transfer Switch to reboot or reset relative setting to default value.
1.3.6.1.4.1.3808.1.1.5.4.1INTEGER {none(1), rboot(2), reset(3)}read-writemandatory
atsCtrlClearEventCounts
OBJECT-TYPE
Setting this variable will clear all event counts in Automatic Transfer Switch. Returns (-1) if unsupported.
1.3.6.1.4.1.3808.1.1.5.4.2INTEGER {none(1), clear(2)}read-writemandatory
atsLoad
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.5
atsLoadDevice
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.5.1
atsLoadDevPhaseTableSize
OBJECT-TYPE
The size of the Phase Table.
1.3.6.1.4.1.3808.1.1.5.5.1.1INTEGERread-onlymandatory
atsLoadDevPhaseTable
OBJECT-TYPE
Allows for getting the Phase Max Load in the ATS.
1.3.6.1.4.1.3808.1.1.5.5.1.2not-accessiblemandatory
atsLoadDevPhaseEntry
OBJECT-TYPE
The ATS Phases Access.
1.3.6.1.4.1.3808.1.1.5.5.1.2.1not-accessiblemandatory
atsLoadDevPhaseTableIndex
OBJECT-TYPE
The index to ATS phase entry.
1.3.6.1.4.1.3808.1.1.5.5.1.2.1.1INTEGER (1..10)read-onlymandatory
atsLoadDevPhase
OBJECT-TYPE
For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), phase3 (3), phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
1.3.6.1.4.1.3808.1.1.5.5.1.2.1.2INTEGER {phase1(1), phase2(2), phase3(3), phase1-2(4), phase2-3(5), phase3-1(6)}read-onlymandatory
atsLoadDevPhaseMaxLoad
OBJECT-TYPE
Getting this OID will return the maximum rated power that each phase of the ATS can provide. It is represented in Amps.
1.3.6.1.4.1.3808.1.1.5.5.1.2.1.3INTEGERread-onlymandatory
atsLoadDevBankTableSize
OBJECT-TYPE
The size of the Bank Table.
1.3.6.1.4.1.3808.1.1.5.5.1.3INTEGERread-onlymandatory
atsLoadDevBankTable
OBJECT-TYPE
Allows for getting the Bank Max Load in the ATS.
1.3.6.1.4.1.3808.1.1.5.5.1.4not-accessiblemandatory
atsLoadDevBankEntry
OBJECT-TYPE
The ATS Banks Access.
1.3.6.1.4.1.3808.1.1.5.5.1.4.1not-accessiblemandatory
atsLoadDevBankTableIndex
OBJECT-TYPE
The index to the ATS bank entry.
1.3.6.1.4.1.3808.1.1.5.5.1.4.1.1INTEGER {total(1), bank1(2), bank2(3), bank3(4)}read-onlymandatory
atsLoadDevBankMaxLoad
OBJECT-TYPE
Getting this OID will return the maximum rated power that each bank of the ATS can provide. It is represented in Amps.
1.3.6.1.4.1.3808.1.1.5.5.1.4.1.2INTEGERread-onlymandatory
atsLoadStatus
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.5.2
atsLoadStatusPhaseTableSize
OBJECT-TYPE
The size of the Phase Table.
1.3.6.1.4.1.3808.1.1.5.5.2.1INTEGERread-onlymandatory
atsLoadStatusPhaseTable
OBJECT-TYPE
Allows for getting the Phase Load status in the ATS.
1.3.6.1.4.1.3808.1.1.5.5.2.2not-accessiblemandatory
atsLoadStatusPhaseEntry
OBJECT-TYPE
The ATS Phases Access.
1.3.6.1.4.1.3808.1.1.5.5.2.2.1not-accessiblemandatory
atsLoadStatusPhaseTableIndex
OBJECT-TYPE
The index to ATS phase entry.
1.3.6.1.4.1.3808.1.1.5.5.2.2.1.1INTEGER (1..10)read-onlymandatory
atsLoadStatusPhase
OBJECT-TYPE
For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), phase3 (3), phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
1.3.6.1.4.1.3808.1.1.5.5.2.2.1.2INTEGER {phase1(1), phase2(2), phase3(3), phase1-2(4), phase2-3(5), phase3-1(6)}read-onlymandatory
atsLoadStatusPhaseLoad
OBJECT-TYPE
The output current in 0.1 amperes drawn by the load on the ATS
1.3.6.1.4.1.3808.1.1.5.5.2.2.1.3INTEGERread-onlymandatory
atsLoadStatusPhaseLoadState
OBJECT-TYPE
Getting this OID will return the phase load state.
1.3.6.1.4.1.3808.1.1.5.5.2.2.1.4INTEGER {normal(1), lowLoad(2), nearOverLoad(3), overLoad(4)}read-onlymandatory
atsLoadStatusPhasePower
OBJECT-TYPE
The output power in Watts.
1.3.6.1.4.1.3808.1.1.5.5.2.2.1.5INTEGERread-onlymandatory
atsLoadStatusBankTableSize
OBJECT-TYPE
The size of the Bank Table.
1.3.6.1.4.1.3808.1.1.5.5.2.3INTEGERread-onlymandatory
atsLoadStatusBankTable
OBJECT-TYPE
Allows for getting the Bank Load status in the ATS.
1.3.6.1.4.1.3808.1.1.5.5.2.4not-accessiblemandatory
atsLoadStatusBankEntry
OBJECT-TYPE
The ATS Bank Access.
1.3.6.1.4.1.3808.1.1.5.5.2.4.1not-accessiblemandatory
atsLoadStatusBankTableIndex
OBJECT-TYPE
The index to ATS bank entry.
1.3.6.1.4.1.3808.1.1.5.5.2.4.1.1INTEGER {total(1), bank1(2), bank2(3), bank3(4)}read-onlymandatory
atsLoadStatusBankPhase
OBJECT-TYPE
Getting this OID will return the phase number.
1.3.6.1.4.1.3808.1.1.5.5.2.4.1.2INTEGER {phase1(1), phase2(2), phase3(3), phase1-2(4), phase2-3(5), phase3-1(6)}read-onlymandatory
atsLoadStatusBankLoad
OBJECT-TYPE
The output current in 0.1 amperes drawn by the load on the ATS
1.3.6.1.4.1.3808.1.1.5.5.2.4.1.3INTEGERread-onlymandatory
atsLoadStatusBankLoadState
OBJECT-TYPE
Getting this OID will return the bank load state.
1.3.6.1.4.1.3808.1.1.5.5.2.4.1.4INTEGER {normal(1), lowLoad(2), nearOverLoad(3), overLoad(4)}read-onlymandatory
atsLoadStatusBankPower
OBJECT-TYPE
The output power in Watts.
1.3.6.1.4.1.3808.1.1.5.5.2.4.1.5INTEGERread-onlymandatory
atsLoadStatusBankEnergy
OBJECT-TYPE
Getting this OID will return the phase/bank apparent power measured in 0.1 kilowatt-hours.
1.3.6.1.4.1.3808.1.1.5.5.2.4.1.6INTEGERread-onlymandatory
atsLoadStatusBankStartTime
OBJECT-TYPE
Getting this OID will return the date and time of the last energy meter reset
1.3.6.1.4.1.3808.1.1.5.5.2.4.1.7INTEGERread-onlymandatory
atsLoadConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.5.3
atsLoadCfgPhaseTableSize
OBJECT-TYPE
The size of the Phase Table.
1.3.6.1.4.1.3808.1.1.5.5.3.1INTEGERread-onlymandatory
atsLoadCfgPhaseTable
OBJECT-TYPE
Allows for configuration of each ATS phase.
1.3.6.1.4.1.3808.1.1.5.5.3.2not-accessiblemandatory
atsLoadCfgPhaseEntry
OBJECT-TYPE
The ATS phase to configure.
1.3.6.1.4.1.3808.1.1.5.5.3.2.1not-accessiblemandatory
atsLoadCfgPhaseTableIndex
OBJECT-TYPE
The index to the ATS phase entry.
1.3.6.1.4.1.3808.1.1.5.5.3.2.1.1INTEGER (1..10)read-onlymandatory
atsLoadCfgPhase
OBJECT-TYPE
For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), phase3 (3), phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
1.3.6.1.4.1.3808.1.1.5.5.3.2.1.2INTEGER {phase1(1), phase2(2), phase3(3), phase1-2(4), phase2-3(5), phase3-1(6)}read-onlymandatory
atsLoadCfgPhaseLowLoad
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in Amps. A warning will be issued when the load is less than the threshold value. A threshold value of 0 Amps effectively disables this warning.
1.3.6.1.4.1.3808.1.1.5.5.3.2.1.3INTEGERread-writemandatory
atsLoadCfgPhaseNearOverLoad
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value.
1.3.6.1.4.1.3808.1.1.5.5.3.2.1.4INTEGERread-writemandatory
atsLoadCfgPhaseOverLoad
OBJECT-TYPE
A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value.
1.3.6.1.4.1.3808.1.1.5.5.3.2.1.5INTEGERread-writemandatory
atsLoadCfgPhaseOutletRestriction
OBJECT-TYPE
This OID controls the behavior of a ATS phase when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding phase to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigOverloadThreshold OID is exceeded.
1.3.6.1.4.1.3808.1.1.5.5.3.2.1.6INTEGER {alwaysAllowTurnON(1), restrictOnNearOverload(2), restrictOnOverload(3)}read-writemandatory
atsLoadCfgBankTableSize
OBJECT-TYPE
The size of the Bank Table.
1.3.6.1.4.1.3808.1.1.5.5.3.3INTEGERread-onlymandatory
atsLoadCfgBankTable
OBJECT-TYPE
Allows for configuration of each ATS bank.
1.3.6.1.4.1.3808.1.1.5.5.3.4not-accessiblemandatory
atsLoadCfgBankEntry
OBJECT-TYPE
The ATS phase to configure.
1.3.6.1.4.1.3808.1.1.5.5.3.4.1not-accessiblemandatory
atsLoadCfgBankTableIndex
OBJECT-TYPE
The index to the ATS bank entry.
1.3.6.1.4.1.3808.1.1.5.5.3.4.1.1INTEGER {total(1), bank1(2), bank2(3), bank3(4)}read-onlymandatory
atsLoadCfgBankLowLoad
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing a low consumption condition. It is represented in Amps. A warning will be issued when the load is less than the threshold value. A threshold value of 0 Amps effectively disables this warning.
1.3.6.1.4.1.3808.1.1.5.5.3.4.1.2INTEGERread-writemandatory
atsLoadCfgBankNearOverLoad
OBJECT-TYPE
A threshold that indicates the power consumption of the load is nearing an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value.
1.3.6.1.4.1.3808.1.1.5.5.3.4.1.3INTEGERread-writemandatory
atsLoadCfgBankOverLoad
OBJECT-TYPE
A threshold that indicates the power consumption of the load has entered an overload condition. It is represented in Amps. A warning will be issued when the load is greater than or equal to the threshold value.
1.3.6.1.4.1.3808.1.1.5.5.3.4.1.4INTEGERread-writemandatory
atsLoadCfgBankOutletRestriction
OBJECT-TYPE
This OID controls the behavior of a ATS phase when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding phase to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding phase to turn on if the ePDULoadConfigOverloadThreshold OID is exceeded.
1.3.6.1.4.1.3808.1.1.5.5.3.4.1.5INTEGER {alwaysAllowTurnON(1), restrictOnNearOverload(2), restrictOnOverload(3)}read-writemandatory
atsOutlet
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.6
atsOutletDevice
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.5.6.1
atsOutletDevTotalOutletNum
OBJECT-TYPE
The total number of outlets on the ATS.
1.3.6.1.4.1.3808.1.1.5.6.1.1INTEGERread-onlymandatory
atsOutletDevCtrlOutletNum
OBJECT-TYPE
The number of controlled outlets on the ATS.
1.3.6.1.4.1.3808.1.1.5.6.1.2INTEGERread-onlymandatory
atsOutletDevColdStartDelay
OBJECT-TYPE
The amount of delay, in seconds, between when power is provided to the ATS and when the ATS provides basic master power to the outlets. Allowed values are: -1 - never apply power automatically. 0 - apply power immediately. 1 to 300 - delay up to 300 seconds (5 minutes).
1.3.6.1.4.1.3808.1.1.5.6.1.3INTEGERread-writemandatory
atsOutletDevColdStartState
OBJECT-TYPE
The ATS outlet state after coldstart. Allowed values are: 1 - all outlets on after coldstart. 2 - outlet status same as previous state.
1.3.6.1.4.1.3808.1.1.5.6.1.4INTEGER {allOn(1), previous(2)}read-writemandatory
atsOutletDevLocalCtrl
OBJECT-TYPE
To configure enable or disable outlet local control function.
1.3.6.1.4.1.3808.1.1.5.6.1.5INTEGER {enable(1), disable(2)}read-writemandatory
atsOutletDevCommand
OBJECT-TYPE
Setting this OID to immediateAllOn (2) will turn all outlets on immediately. Setting this OID to immediateAllOff (3) will turn all outlets off immediately. Setting this OID to immediateAllReboot (4) will reboot all outlets immediately. Setting this OID to delayedAllOn (5) will turn all outlets on as defined by each outlet's atsOutletCfgPowerOnTime OID value. Setting this OID to delayedAllOff (6) will turn all outlets off as defined by each outlet's atsOutletCfgPowerOffTime OID value. Setting this OID to delayedAllReboot (7) will cause a delayedAllOff command to be performed. Once all outlets are off, the Switched Rack ATS will then delay the largest atsOutletCfgRebootDuration OID time, and then perform a delayedAllOn command. Setting this OID to cancelAllPendingCommands (8) will cause all pending commands on the Switched Rack ATS to be canceled. Getting this OID will return the noCommandAll (1) value.
1.3.6.1.4.1.3808.1.1.5.6.1.6INTEGER {noCommandAll(1), immediateAllOn(2), immediateAllOff(3), immediateAllReboot(4), delayedAllOn(5), delayedAllOff(6), delayedAllReboot(7), cancelAllPendingCommands(8)}read-writemandatory
atsOutletStatusTableSize
OBJECT-TYPE
The size of the outlet status table.
1.3.6.1.4.1.3808.1.1.5.6.2INTEGERread-onlymandatory
atsOutletStatusTable
OBJECT-TYPE
Allows for getting of status of individual outlets.
1.3.6.1.4.1.3808.1.1.5.6.3not-accessiblemandatory
atsOutletStatusEntry
OBJECT-TYPE
The outlet to gather status from.
1.3.6.1.4.1.3808.1.1.5.6.3.1not-accessiblemandatory
atsOutletStatusTableIndex
OBJECT-TYPE
The index to the outlet entry.
1.3.6.1.4.1.3808.1.1.5.6.3.1.1INTEGER (1..19)read-onlymandatory
atsOutletStatusOutletName
OBJECT-TYPE
The name of the outlet. The maximum string size is device dependent. This OID is provided for informational purposes only.
1.3.6.1.4.1.3808.1.1.5.6.3.1.2DisplayStringread-onlymandatory
atsOutletStatusOutletState
OBJECT-TYPE
Getting this variable will return the outlet state. If the outlet is on, the outletStatusOn (1) value will be returned. If the outlet is off, the outletStatusOff (2) value will be returned.
1.3.6.1.4.1.3808.1.1.5.6.3.1.3INTEGER {outletStatusOn(1), outletStatusOff(2)}read-onlymandatory
atsOutletStatusOutletCmdPending
OBJECT-TYPE
Getting this variable will return the command pending state of the outlet. If a command is pending on the outlet, the outletStatusCommandPending (1) value will be returned. If there is not a command pending on the outlet, the outletStatusNoCommandPending (2) will be returned.
1.3.6.1.4.1.3808.1.1.5.6.3.1.4INTEGER {outletStatusCommandPending(1), outletStatusNoCommandPending(2)}read-onlymandatory
atsOutletStatusOutletPhase
OBJECT-TYPE
The phase/s associated with this outlet. For single phase devices, this object will always return phase1(1). For 3-phase devices, this object will return phase1 (1), phase2 (2), or phase3 (3) for outlets tied to a single phase. For outlets tied to two phases, this object will return phase1-2 (4) for phases 1 and 2, phase2-3 (5) for phases 2 and 3, and phase3-1 (6) for phases 3 and 1.
1.3.6.1.4.1.3808.1.1.5.6.3.1.5INTEGER {phase1(1), phase2(2), phase3(3), phase1-2(4), phase2-3(5), phase3-1(6)}read-onlymandatory
atsOutletStatusOutletBank
OBJECT-TYPE
The bank associated with this outlet.
1.3.6.1.4.1.3808.1.1.5.6.3.1.6INTEGERread-onlymandatory
atsOutletCtrlTableSize
OBJECT-TYPE
The size of the outlet control table.
1.3.6.1.4.1.3808.1.1.5.6.4INTEGERread-onlymandatory
atsOutletCtrlTable
OBJECT-TYPE
Allows for control of the individual outlets.
1.3.6.1.4.1.3808.1.1.5.6.5not-accessiblemandatory
atsOutletCtrlEntry
OBJECT-TYPE
The outlet to control.
1.3.6.1.4.1.3808.1.1.5.6.5.1not-accessiblemandatory
atsOutletCtrlTableIndex
OBJECT-TYPE
The index to the outlet entry.
1.3.6.1.4.1.3808.1.1.5.6.5.1.1INTEGER (1..19)read-onlymandatory
atsOutletCtrlOutletName
OBJECT-TYPE
The name of the outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size. This OID is provided for informational purposes only.
1.3.6.1.4.1.3808.1.1.5.6.5.1.2DisplayStringread-onlymandatory
atsOutletCtrlCommand
OBJECT-TYPE
Getting this variable will return the outlet state. If the outlet is on, the immediateOn (2) value will be returned. If the outlet is off, the immediateOff (2) value will be returned. Setting this variable to immediateOn (2) will immediately turn the outlet on. Setting this variable to immediateOff (3) will immediately turn the outlet off. Setting this variable to immediateReboot (4) will immediately reboot the outlet. Setting this variable to delayedOn (5) will turn the outlet on after the ePDUOutletConfigPowerOnTime OID time has elapsed. Setting this variable to delayedOff (6) will turn the outlet off after the ePDUOutletConfigPowerOffTime OID time has elapsed. Setting this variable to delayedReboot (7) will cause the ATS to perform a delayedOff command, wait the atsOutletCfgRebootDuration OID time, and then perform a delayedOn command. Setting this variable to cancelPendingCommand (8) will cause any pending command to this outlet to be canceled.
1.3.6.1.4.1.3808.1.1.5.6.5.1.3INTEGER {none(1), immediateOn(2), immediateOff(3), immediateReboot(4), delayedOn(5), delayedOff(6), delayedReboot(7), cancelPendingCommand(8)}read-writemandatory
atsOutletCfgTableSize
OBJECT-TYPE
The size of the outlet config table.
1.3.6.1.4.1.3808.1.1.5.6.6INTEGERread-onlymandatory
atsOutletCfgTable
OBJECT-TYPE
Allows for configuration of individual outlets.
1.3.6.1.4.1.3808.1.1.5.6.7not-accessiblemandatory
atsOutletCfgEntry
OBJECT-TYPE
The outlet to configure.
1.3.6.1.4.1.3808.1.1.5.6.7.1not-accessiblemandatory
atsOutletCfgTableIndex
OBJECT-TYPE
The index to the outlet entry.
1.3.6.1.4.1.3808.1.1.5.6.7.1.1INTEGER (1..19)read-onlymandatory
atsOutletCfgOutletName
OBJECT-TYPE
The name of the outlet. The maximum string size is device dependent. An error will be returned if the set request exceeds the max size.
1.3.6.1.4.1.3808.1.1.5.6.7.1.2DisplayStringread-writemandatory
atsOutletCfgPowerOnTime
OBJECT-TYPE
The amount of time (in seconds) the outlet will delay powering on at coldstart or when a command that requires a turn-on delay is issued. Allowed values are: -1 - never power on. 0 - power on immediately. 1 to 7200 - power on up to 7200 seconds after being commanded.
1.3.6.1.4.1.3808.1.1.5.6.7.1.3INTEGERread-writemandatory
atsOutletCfgPowerOffTime
OBJECT-TYPE
The amount of time (in seconds) the outlet will delay powering off when a command that requires a turn-off delay is issued. Allowed values are: -1 - never power off. 0 - power off immediately. 1 to 7200 - power off up to 7200 seconds after being commanded.
1.3.6.1.4.1.3808.1.1.5.6.7.1.4INTEGERread-writemandatory
atsOutletCfgRebootDuration
OBJECT-TYPE
During a reboot sequence, power is turned off and then back on. This OID defines the amount of time to wait, in seconds, after turning the power off, at the start of the sequence, before turning power back on, at the end of the reboot sequence. Allowed range is any value between 5 and 60 seconds (1 minute).
1.3.6.1.4.1.3808.1.1.5.6.7.1.5INTEGERread-writemandatory
ePDU2
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6
ePDU2Role
OBJECT-TYPE
Get this oid shows the role the PDU played on Daisy Chain Group. The PDU as a Host can access whole ePDU2 content, and the PDU be standalong or a Slave can access itself instead.
1.3.6.1.4.1.3808.1.1.6.1INTEGER {standalone(1), host(2), slave(3)}read-onlymandatory
ePDU2Ident
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.2
ePDU2IdentTableSize
OBJECT-TYPE
PDU as a Host response total PDU ident number on daisy chain. PDU as a Slave can only response 1.
1.3.6.1.4.1.3808.1.1.6.2.1INTEGERread-onlymandatory
ePDU2IdentTable
OBJECT-TYPE
A table of Rack PDU identification information.
1.3.6.1.4.1.3808.1.1.6.2.2not-accessiblemandatory
ePDU2IdentEntry
OBJECT-TYPE
Identification data from Rack PDU being queried.
1.3.6.1.4.1.3808.1.1.6.2.2.1not-accessiblemandatory
ePDU2IdentIndex
OBJECT-TYPE
The index to the Rack PDU identification table entry.
1.3.6.1.4.1.3808.1.1.6.2.2.1.1INTEGER (1..4)read-onlymandatory
ePDU2IdentModuleIndex
OBJECT-TYPE
The Rack PDU identification table entry numeric ID.
1.3.6.1.4.1.3808.1.1.6.2.2.1.2INTEGERread-onlymandatory
ePDU2IdentName
OBJECT-TYPE
A user-defined string identifying the name of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.2.2.1.3DisplayStringread-onlymandatory
ePDU2IdentLocation
OBJECT-TYPE
A user-defined string identifying the location of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.2.2.1.4DisplayStringread-onlymandatory
ePDU2IdentContact
OBJECT-TYPE
A user-defined string identifying the person to contact of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.2.2.1.5DisplayStringread-onlymandatory
ePDU2IdentHardwareRev
OBJECT-TYPE
The Rack PDU hardware version.
1.3.6.1.4.1.3808.1.1.6.2.2.1.6DisplayStringread-onlymandatory
ePDU2IdentFirmwareRev
OBJECT-TYPE
The Rack PDU firmware version.
1.3.6.1.4.1.3808.1.1.6.2.2.1.7DisplayStringread-onlymandatory
ePDU2IdentDateOfManufacture
OBJECT-TYPE
The date the Rack PDU was manufactured in mm/dd/yyyy format.
1.3.6.1.4.1.3808.1.1.6.2.2.1.8DisplayStringread-onlymandatory
ePDU2IdentModelName
OBJECT-TYPE
The Rack PDU model number.
1.3.6.1.4.1.3808.1.1.6.2.2.1.9DisplayStringread-onlymandatory
ePDU2IdentSerialNumber
OBJECT-TYPE
The Rack PDU serial number.
1.3.6.1.4.1.3808.1.1.6.2.2.1.10DisplayStringread-onlymandatory
ePDU2IdentIndicator
OBJECT-TYPE
PDU will perform a panel indicator test when the variable is set to testIndicators(2). It is no effective to set this value to noTestIndicators(1).
1.3.6.1.4.1.3808.1.1.6.2.2.1.11INTEGER {noTestIndicators(1), testIndicators(2)}read-writemandatory
ePDU2Device
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.3
ePDU2DeviceTableSize
OBJECT-TYPE
A Host Rack PDU response total number of Rack PDUs on daisy chain. Rack PDU as a Slave can only response 1.
1.3.6.1.4.1.3808.1.1.6.3.1INTEGERread-onlymandatory
ePDU2DeviceConfigTable
OBJECT-TYPE
A table of Rack PDU configuration data.
1.3.6.1.4.1.3808.1.1.6.3.2not-accessiblemandatory
ePDU2DeviceConfigEntry
OBJECT-TYPE
Configuration data from Rack PDU being queried.
1.3.6.1.4.1.3808.1.1.6.3.2.1not-accessiblemandatory
ePDU2DeviceConfigIndex
OBJECT-TYPE
The index to the Rack PDU table entry.
1.3.6.1.4.1.3808.1.1.6.3.2.1.1INTEGER (1..4)read-onlymandatory
ePDU2DeviceConfigModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.3.2.1.2INTEGERread-onlymandatory
ePDU2DeviceConfigName
OBJECT-TYPE
A user-defined string identifying the name of Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.2.1.3DisplayStringread-writemandatory
ePDU2DeviceConfigLocation
OBJECT-TYPE
A user-defined string identifying the location of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.2.1.4DisplayStringread-writemandatory
ePDU2DeviceConfigContact
OBJECT-TYPE
A user-defined string identifying the person to contact of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.2.1.5DisplayStringread-writemandatory
ePDU2DeviceConfigDisplayOrientation
OBJECT-TYPE
Getting this OID will return the intended physical orientation of the Seven-Segment Display. displayNormal(1) indicates Normal. displayReverse(2)indicates Upside-Down. displayRotate90(3) indicates rotate 90 degree. displayRotate270(4) indicates rotate 270 degree. displayAuto(5) indicates auto-detect and rotate.
1.3.6.1.4.1.3808.1.1.6.3.2.1.6INTEGER {displayNormal(1), displayReverse(2), displayRotate90(3), displayRotate270(4), displayAuto(5)}read-writemandatory
ePDU2DeviceConfigColdstartDelay
OBJECT-TYPE
The amount of delay, measured in seconds, between when power is provided to the Rack PDU and when the Rack PDU provides basic master power to the outlets. Allowed values are: -1 - never apply power automatically. 0 - apply power immediately. 1 to 300 - delay up to 300 seconds (5 minutes).
1.3.6.1.4.1.3808.1.1.6.3.2.1.7INTEGERread-writemandatory
ePDU2DeviceConfigCurrentLowLoadThreshold
OBJECT-TYPE
User-defined low current draw alarm threshold, measured in Amps.
1.3.6.1.4.1.3808.1.1.6.3.2.1.8INTEGERread-writemandatory
ePDU2DeviceConfigCurrentNearOverloadThreshold
OBJECT-TYPE
User-defined near overload current threshold, measured in Amps.
1.3.6.1.4.1.3808.1.1.6.3.2.1.9INTEGERread-writemandatory
ePDU2DeviceConfigCurrentOverloadThreshold
OBJECT-TYPE
User-defined current overload threshold, measured in Amps.
1.3.6.1.4.1.3808.1.1.6.3.2.1.10INTEGERread-writemandatory
ePDU2DeviceConfigPeakLoadReset
OBJECT-TYPE
Setting this OID to resetAll (2) will cause the existing peak current value of Rack PDU and its outlets to be replaced by the current load current value. Setting this OID to resetDevice (3) to reset the Rack PDU only. Setting this OID to resetOutlets (4) to reset the PDU outlets only. Getting this OID will do nothing and return the noOperation(1) value.
1.3.6.1.4.1.3808.1.1.6.3.2.1.11INTEGER {noOperation(1), resetAll(2), resetDevice(3), resetOutlets(4)}read-writemandatory
ePDU2DeviceConfigEnergyReset
OBJECT-TYPE
Setting this OID to resetAll (2) will cause the device energy meter value to be reset to zero. Setting this OID to resetDevice (3) to reset the Rack PDU only. Setting this OID to resetOutlets (4) to reset the PDU outlets only. Getting this OID in models that support this feature will do nothing and return the noOperation(1) value.
1.3.6.1.4.1.3808.1.1.6.3.2.1.12INTEGER {noOperation(1), resetAll(2), resetDevice(3), resetOutlets(4)}read-writemandatory
ePDU2DeviceConfigPowerLowLoadThreshold
OBJECT-TYPE
User-defined low power draw alarm threshold, measured in Watts.
1.3.6.1.4.1.3808.1.1.6.3.2.1.13INTEGERread-writemandatory
ePDU2DeviceConfigPowerNearOverloadThreshold
OBJECT-TYPE
User-defined near overload power threshold, measured in Watts.
1.3.6.1.4.1.3808.1.1.6.3.2.1.14INTEGERread-writemandatory
ePDU2DeviceConfigPowerOverloadThreshold
OBJECT-TYPE
User-defined power overload threshold, measured in Watts.
1.3.6.1.4.1.3808.1.1.6.3.2.1.15INTEGERread-writemandatory
ePDU2DeviceInfoTable
OBJECT-TYPE
A table of Rack PDU information.
1.3.6.1.4.1.3808.1.1.6.3.3not-accessiblemandatory
ePDU2DeviceInfoEntry
OBJECT-TYPE
Information of the Rack PDU being queried.
1.3.6.1.4.1.3808.1.1.6.3.3.1not-accessiblemandatory
ePDU2DeviceInfoIndex
OBJECT-TYPE
The index to the Rack PDU Information table entry.
1.3.6.1.4.1.3808.1.1.6.3.3.1.1INTEGER (1..4)read-onlymandatory
ePDU2DeviceInfoModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.3.3.1.2INTEGERread-onlymandatory
ePDU2DeviceInfoName
OBJECT-TYPE
A user-defined string identifying the name of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.3.1.3DisplayStringread-onlymandatory
ePDU2DeviceInfoRating
OBJECT-TYPE
The electrical rating of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.3.1.4INTEGERread-onlymandatory
ePDU2DeviceInfoNumOutlets
OBJECT-TYPE
The number of outlets on the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.3.1.5INTEGERread-onlymandatory
ePDU2DeviceInfoSwitchedOutlets
OBJECT-TYPE
The number of switched outlets on the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.3.1.6INTEGERread-onlymandatory
ePDU2DeviceInfoMeteredOutlets
OBJECT-TYPE
The number of metered outlets on the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.3.1.7INTEGERread-onlymandatory
ePDU2DeviceInfoNumPhases
OBJECT-TYPE
The number of phases present in the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.3.1.8INTEGERread-onlymandatory
ePDU2DeviceInfoNumBreakers
OBJECT-TYPE
The number of metered banks present in the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.3.1.9INTEGERread-onlymandatory
ePDU2DeviceInfoBreakerRating
OBJECT-TYPE
The maximum current rating, measured in Amps, for the Rack PDU. Getting this OID will return rating of the circuit breakers on the device if it has any.
1.3.6.1.4.1.3808.1.1.6.3.3.1.10INTEGERread-onlymandatory
ePDU2DeviceInfoOrientation
OBJECT-TYPE
Rack PDU orientation.
1.3.6.1.4.1.3808.1.1.6.3.3.1.11INTEGER {orientHorizontal(1), orientVertical(2)}read-onlymandatory
ePDU2DeviceInfoOutletLayout
OBJECT-TYPE
Getting this OID will return outlet layout for the device. SeqPhaseToNeutral(1) indicates outlet layout as follows: 1:1-N,2:2-N,3:3-N,4:1-N,5:2-N,... SeqPhaseToPhase(2) indicates outlet layout as follows: 1:1-2,2:2-3,3:3-1,4:1-2,5:2-3,... SeqPhToNeu21PhToPh(3) indicates outlet layout as follows: 1:1-N,2:2-N...21:3-N,22:1-2,23:2-3,24:3-1,... SeqPhToPhGrouped(4) indicates outlet layout as follows: Otlts1-8::(3-1),Otlts9-16::(2-3),Otlts17-24::(1-2).
1.3.6.1.4.1.3808.1.1.6.3.3.1.12INTEGER {seqPhaseToNeutral(1), seqPhaseToPhase(2), seqPhToNeu21PhToPh(3), seqPhToPhGrouped(4)}read-onlymandatory
ePDU2DeviceStatusTable
OBJECT-TYPE
A table of Rack PDU current status.
1.3.6.1.4.1.3808.1.1.6.3.4not-accessiblemandatory
ePDU2DeviceStatusEntry
OBJECT-TYPE
Status data from the Rack PDU being queried.
1.3.6.1.4.1.3808.1.1.6.3.4.1not-accessiblemandatory
ePDU2DeviceStatusIndex
OBJECT-TYPE
The index to the Rack PDU status table entry.
1.3.6.1.4.1.3808.1.1.6.3.4.1.1INTEGER (1..4)read-onlymandatory
ePDU2DeviceStatusModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID
1.3.6.1.4.1.3808.1.1.6.3.4.1.2INTEGERread-onlymandatory
ePDU2DeviceStatusName
OBJECT-TYPE
A user-defined string identifying the name of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.4.1.3DisplayStringread-onlymandatory
ePDU2DeviceStatusLoadState
OBJECT-TYPE
Indicates the present load status of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.4.1.4INTEGER {noLoadAlarm(1), underCurrentAlarm(2), nearOverCurrentAlarm(3), overCurrentAlarm(4)}read-onlymandatory
ePDU2DeviceStatusCurrentLoad
OBJECT-TYPE
The power consumption of the Rack PDU load in tenths of Amps.
1.3.6.1.4.1.3808.1.1.6.3.4.1.5Gaugeread-onlymandatory
ePDU2DeviceStatusCurrentPeakLoad
OBJECT-TYPE
The peak power consumption of the Rack PDU load in tenths of Amps.
1.3.6.1.4.1.3808.1.1.6.3.4.1.6Gaugeread-onlymandatory
ePDU2DeviceStatusPeakLoadTimestamp
OBJECT-TYPE
Indicates the date and time that peak load occurred.
1.3.6.1.4.1.3808.1.1.6.3.4.1.7DisplayStringread-onlymandatory
ePDU2DeviceStatusPeakLoadStartTime
OBJECT-TYPE
Indicates the date and time of the last device peak load reset.
1.3.6.1.4.1.3808.1.1.6.3.4.1.8DisplayStringread-onlymandatory
ePDU2DeviceStatusEnergy
OBJECT-TYPE
A user resettable energy meter measuring Rack PDU load energy consumption in tenths of kilowatt-hours.
1.3.6.1.4.1.3808.1.1.6.3.4.1.9Gaugeread-onlymandatory
ePDU2DeviceStatusEnergyStartTime
OBJECT-TYPE
Indicates the date and time of the last device energy meter reset.
1.3.6.1.4.1.3808.1.1.6.3.4.1.10DisplayStringread-onlymandatory
ePDU2DeviceStatusCommandPending
OBJECT-TYPE
Indicates whether or not the device is processing a pending command.
1.3.6.1.4.1.3808.1.1.6.3.4.1.11INTEGER {commandPending(1), noCommandPending(2)}read-onlymandatory
ePDU2DeviceStatusPowerSupplyAlarm
OBJECT-TYPE
Indicates a power supply alarm is active when value equals alarm (2).
1.3.6.1.4.1.3808.1.1.6.3.4.1.12INTEGER {normal(1), alarm(2)}read-onlymandatory
ePDU2DeviceStatusPowerSupply1Status
OBJECT-TYPE
Indicates whether or not an alarm is active in Power Supply 1.
1.3.6.1.4.1.3808.1.1.6.3.4.1.13INTEGER {normal(1), alarm(2)}read-onlymandatory
ePDU2DeviceStatusPowerSupply2Status
OBJECT-TYPE
Indicates whether or not an alarm is active in Power Supply 2.
1.3.6.1.4.1.3808.1.1.6.3.4.1.14INTEGER {normal(1), alarm(2)}read-onlymandatory
ePDU2DeviceStatusApparentPower
OBJECT-TYPE
The apparent power consumption of the Rack PDU load in VoltAmps (VA).
1.3.6.1.4.1.3808.1.1.6.3.4.1.15Gaugeread-onlymandatory
ePDU2DeviceStatusPowerFactor
OBJECT-TYPE
The power factor of the Rack PDU load in hundredths.
1.3.6.1.4.1.3808.1.1.6.3.4.1.16Gaugeread-onlymandatory
ePDU2DeviceStatusRoleType
OBJECT-TYPE
Get this oid shows the role the PDU played on Daisy Chain Group. The PDU as a Host can access whole ePDU2 content, and the PDU be standalong or a Slave can access itself instead.
1.3.6.1.4.1.3808.1.1.6.3.4.1.17INTEGER {standalone(1), host(2), slave(3)}read-onlymandatory
ePDU2DeviceStatusPowerLoad
OBJECT-TYPE
The power consumption of the Rack PDU load in Watts.
1.3.6.1.4.1.3808.1.1.6.3.4.1.18Gaugeread-onlymandatory
ePDU2DeviceStatusPowerPeakLoad
OBJECT-TYPE
The peak power consumption of the Rack PDU load in Watts.
1.3.6.1.4.1.3808.1.1.6.3.4.1.19Gaugeread-onlymandatory
ePDU2DeviceControlTable
OBJECT-TYPE
A table of Rack PDU control data.
1.3.6.1.4.1.3808.1.1.6.3.5not-accessiblemandatory
ePDU2DeviceControlEntry
OBJECT-TYPE
Control data from Rack PDU being queried.
1.3.6.1.4.1.3808.1.1.6.3.5.1not-accessiblemandatory
ePDU2DeviceControlIndex
OBJECT-TYPE
The index to the Rack PDU control table entry.
1.3.6.1.4.1.3808.1.1.6.3.5.1.1INTEGER (1..4)read-onlymandatory
ePDU2DeviceControlModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.3.5.1.2INTEGERread-onlymandatory
ePDU2DeviceControlName
OBJECT-TYPE
A user-defined string identifying the name of the Rack PDU.
1.3.6.1.4.1.3808.1.1.6.3.5.1.3DisplayStringread-onlymandatory
ePDU2DeviceControlCommand
OBJECT-TYPE
Setting this OID to immediateAllOn (1) will turn all outlets on immediately. Setting this OID to immediateAllOff (2) will turn all outlets off immediately. Setting this OID to immediateAllReboot (3) will cause an immediateAllOff command to be performed. Once all outlets are off, the Switched Rack PDU will then delay the ePDU2OutletSwitchedConfigRebootDuration OID time, and then perform an immediateAllOn command. Setting this OID to delayedAllOn (4) will turn all outlets on as defined by each outlet's ePDU2OutletSwitchedConfigPowerOnTime OID value. Setting this OID to delayedAllOff (5) will turn all outlets off as defined by each outlet's ePDU2OutletSwitchedConfigPowerOffTime OID value. Setting this OID to delayedAllReboot (6) will cause a delayedAllOff command to be performed. Once all outlets are off, the Switched Rack PDU will then delay the largest ePDU2OutletSwitchedConfigRebootDuration OID time, and then perform a delayedAllOn command. Setting this OID to cancelAllPendingCommand (7) will cause all pending commands on the Switched Rack PDU to be cancelled. Setting this OID to noCommand (8) will have no effect. Getting this OID will return the noCommand (8) value.
1.3.6.1.4.1.3808.1.1.6.3.5.1.4INTEGER {immediateAllOn(1), immediateAllOff(2), immediateAllReboot(3), delayedAllOn(4), delayedAllOff(5), delayedAllReboot(6), cancelAllPendingCommand(7), noCommand(8)}read-writemandatory
ePDU2Phase
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.4
ePDU2PhaseTableSize
OBJECT-TYPE
A Host Rack PDU response total phase number of Rack PDUs on daisy chain. Rack PDU as a Slave can only response itself number of phase.
1.3.6.1.4.1.3808.1.1.6.4.1INTEGERread-onlymandatory
ePDU2PhaseConfigTable
OBJECT-TYPE
A table of Rack PDU phase configuration data.
1.3.6.1.4.1.3808.1.1.6.4.2not-accessiblemandatory
ePDU2PhaseConfigEntry
OBJECT-TYPE
Configuration data from currently queried Rack PDU phase.
1.3.6.1.4.1.3808.1.1.6.4.2.1not-accessiblemandatory
ePDU2PhaseConfigIndex
OBJECT-TYPE
The index to the Rack PDU phase configuration table entry.
1.3.6.1.4.1.3808.1.1.6.4.2.1.1INTEGER (1..12)read-onlymandatory
ePDU2PhaseConfigModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.4.2.1.2INTEGERread-onlymandatory
ePDU2PhaseConfigNumber
OBJECT-TYPE
The numeric phase ID.
1.3.6.1.4.1.3808.1.1.6.4.2.1.3INTEGERread-onlymandatory
ePDU2PhaseConfigOverloadRestriction
OBJECT-TYPE
This OID controls the behavior of a Switched Rack PDU phase when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding phase to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding phase to turn on if the ePDU2PhaseConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding phase to turn on if the ePDU2PhaseConfigOverloadThreshold OID is exceeded. Models that do not support this feature will respond to this OID with a value of notSupported (-1). Attempts to set this OID in these models will fail.
1.3.6.1.4.1.3808.1.1.6.4.2.1.4INTEGER {notSupported(-1), alwaysAllowTurnON(1), restrictOnNearOverload(2), restrictOnOverload(3)}read-writemandatory
ePDU2PhaseConfigLowLoadThreshold
OBJECT-TYPE
User-defined low load phase current threshold in Amps.
1.3.6.1.4.1.3808.1.1.6.4.2.1.5INTEGERread-writemandatory
ePDU2PhaseConfigNearOverloadThreshold
OBJECT-TYPE
User-defined near phase overload current warning threshold in Amps.
1.3.6.1.4.1.3808.1.1.6.4.2.1.6INTEGERread-writemandatory
ePDU2PhaseConfigOverloadThreshold
OBJECT-TYPE
User-defined phase overload current threshold in Amps
1.3.6.1.4.1.3808.1.1.6.4.2.1.7INTEGERread-writemandatory
ePDU2PhaseConfigPhasePeakLoadReset
OBJECT-TYPE
Setting this OID to reset (2) will cause the existing peak current value to be replaced by the present load current value. Getting this OID will do nothing and return the noOperation(1) value.
1.3.6.1.4.1.3808.1.1.6.4.2.1.8INTEGER {noOperation(1), reset(2)}read-writemandatory
ePDU2PhaseInfoTable
OBJECT-TYPE
A table of Rack PDU phase information.
1.3.6.1.4.1.3808.1.1.6.4.3not-accessiblemandatory
ePDU2PhaseInfoEntry
OBJECT-TYPE
Information data from currently queried Rack PDU phase.
1.3.6.1.4.1.3808.1.1.6.4.3.1not-accessiblemandatory
ePDU2PhaseInfoIndex
OBJECT-TYPE
The index to the Rack PDU phase properties table entry.
1.3.6.1.4.1.3808.1.1.6.4.3.1.1INTEGER (1..12)read-onlymandatory
ePDU2PhaseInfoModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.4.3.1.2INTEGERread-onlymandatory
ePDU2PhaseInfoNumber
OBJECT-TYPE
The numeric phase ID.
1.3.6.1.4.1.3808.1.1.6.4.3.1.3INTEGERread-onlymandatory
ePDU2PhaseStatusTable
OBJECT-TYPE
A table of Rack PDU phase status data
1.3.6.1.4.1.3808.1.1.6.4.4not-accessiblemandatory
ePDU2PhaseStatusEntry
OBJECT-TYPE
Status data from currently queried Rack PDU phase
1.3.6.1.4.1.3808.1.1.6.4.4.1not-accessiblemandatory
ePDU2PhaseStatusIndex
OBJECT-TYPE
The index to the Rack PDU phase status table entry.
1.3.6.1.4.1.3808.1.1.6.4.4.1.1INTEGER (1..13)read-onlymandatory
ePDU2PhaseStatusModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.4.4.1.2INTEGERread-onlymandatory
ePDU2PhaseStatusNumber
OBJECT-TYPE
The numeric phase ID.
1.3.6.1.4.1.3808.1.1.6.4.4.1.3INTEGERread-onlymandatory
ePDU2PhaseStatusLoadState
OBJECT-TYPE
Indicates the present load status of the Rack PDU phase being queried.
1.3.6.1.4.1.3808.1.1.6.4.4.1.4INTEGER {normal(1), lowLoad(2), nearOverload(3), overload(4)}read-onlymandatory
ePDU2PhaseStatusLoad
OBJECT-TYPE
Indicates the current draw, in tenths of Amps, of the load on the Rack PDU phase being queried.
1.3.6.1.4.1.3808.1.1.6.4.4.1.5Gaugeread-onlymandatory
ePDU2PhaseStatusVoltage
OBJECT-TYPE
Indicates the Voltage, in tenths of Volts, of the Rack PDU phase being queried
1.3.6.1.4.1.3808.1.1.6.4.4.1.6Gaugeread-onlymandatory
ePDU2PhaseStatusPower
OBJECT-TYPE
Indicates the load power, in watts, consumed on the Rack PDU phase being queried
1.3.6.1.4.1.3808.1.1.6.4.4.1.7Gaugeread-onlymandatory
ePDU2PhaseStatusApparentPower
OBJECT-TYPE
Indicates the load apparent power, in VoltAmps (VA), consumed on the Rack PDU phase being queried
1.3.6.1.4.1.3808.1.1.6.4.4.1.8Gaugeread-onlymandatory
ePDU2PhaseStatusPowerFactor
OBJECT-TYPE
Indicates the load power factor, in hundredths, of the Rack PDU phase being queried
1.3.6.1.4.1.3808.1.1.6.4.4.1.9Gaugeread-onlymandatory
ePDU2PhaseStatusPeakLoad
OBJECT-TYPE
The peak current of the Rack PDU phase load in tenths of Amps
1.3.6.1.4.1.3808.1.1.6.4.4.1.10Gaugeread-onlymandatory
ePDU2PhaseStatusPeakLoadTimestamp
OBJECT-TYPE
Indicates the date and time the phase peak current occurred.
1.3.6.1.4.1.3808.1.1.6.4.4.1.11DisplayStringread-onlymandatory
ePDU2PhaseStatusPeakLoadStartTime
OBJECT-TYPE
Indicates the date and time of the last phase peak current reset.
1.3.6.1.4.1.3808.1.1.6.4.4.1.12DisplayStringread-onlymandatory
ePDU2PhaseStatusLineToLineVoltage
OBJECT-TYPE
Indicates the Line to Line Voltage, in tenths of Volts, of the Rack PDU phase being queried
1.3.6.1.4.1.3808.1.1.6.4.4.1.13Gaugeread-onlymandatory
ePDU2Bank
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.5
ePDU2BankTableSize
OBJECT-TYPE
A Host Rack PDU response total bank number of Rack PDUs on daisy chain. Rack PDU as a Slave can only response itself number of bank.
1.3.6.1.4.1.3808.1.1.6.5.1INTEGERread-onlymandatory
ePDU2BankConfigTable
OBJECT-TYPE
A table of Rack PDU bank configuration data.
1.3.6.1.4.1.3808.1.1.6.5.2not-accessiblemandatory
ePDU2BankConfigEntry
OBJECT-TYPE
Configuration data from currently queried Rack PDU bank.
1.3.6.1.4.1.3808.1.1.6.5.2.1not-accessiblemandatory
ePDU2BankConfigIndex
OBJECT-TYPE
The index to the Rack PDU bank configuration table entry.
1.3.6.1.4.1.3808.1.1.6.5.2.1.1INTEGER (1..12)read-onlymandatory
ePDU2BankConfigModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.5.2.1.2INTEGERread-onlymandatory
ePDU2BankConfigNumber
OBJECT-TYPE
The numeric bank ID.
1.3.6.1.4.1.3808.1.1.6.5.2.1.3INTEGERread-onlymandatory
ePDU2BankConfigOverloadRestriction
OBJECT-TYPE
This OID controls the behavior of a Switched Rack PDU bank when an overload condition is possible and additional outlets are requested to be turned on. Setting this OID to alwaysAllowTurnON (1) will always allow the outlets on the corresponding bank to turn on. Setting this OID to restrictOnNearOverload (2) will not allow outlets on the corresponding bank to turn on if the ePDU2BankConfigNearOverloadThreshold OID is exceeded. Setting this OID to restrictOnOverload (3) will not allow outlets on the corresponding bank to turn on if the ePDU2BankConfigOverloadThreshold OID is exceeded.
1.3.6.1.4.1.3808.1.1.6.5.2.1.4INTEGER {alwaysAllowTurnON(1), restrictOnNearOverload(2), restrictOnOverload(3)}read-writemandatory
ePDU2BankConfigLowLoadThreshold
OBJECT-TYPE
User-defined low load bank current threshold in Amps.
1.3.6.1.4.1.3808.1.1.6.5.2.1.5INTEGERread-writemandatory
ePDU2BankConfigNearOverloadThreshold
OBJECT-TYPE
User-defined near bank overload current warning threshold in Amps.
1.3.6.1.4.1.3808.1.1.6.5.2.1.6INTEGERread-writemandatory
ePDU2BankConfigOverloadThreshold
OBJECT-TYPE
User-defined bank overload current threshold in Amps
1.3.6.1.4.1.3808.1.1.6.5.2.1.7INTEGERread-writemandatory
ePDU2BankConfigPeakLoadReset
OBJECT-TYPE
Setting this OID to reset (2) will cause the existing peak current value to be replaced by the present load current value. Getting this OID will do nothing and return the noOperation(1) value.
1.3.6.1.4.1.3808.1.1.6.5.2.1.8INTEGER {noOperation(1), reset(2)}read-writemandatory
ePDU2BankInfoTable
OBJECT-TYPE
A table of Rack PDU bank information.
1.3.6.1.4.1.3808.1.1.6.5.3not-accessiblemandatory
ePDU2BankInfoEntry
OBJECT-TYPE
Information data from currently queried Rack PDU bank.
1.3.6.1.4.1.3808.1.1.6.5.3.1not-accessiblemandatory
ePDU2BankInfoIndex
OBJECT-TYPE
The index to the Rack PDU bank properties table entry.
1.3.6.1.4.1.3808.1.1.6.5.3.1.1INTEGER (1..12)read-onlymandatory
ePDU2BankInfoModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.5.3.1.2INTEGERread-onlymandatory
ePDU2BankInfoNumber
OBJECT-TYPE
The numeric bank ID.
1.3.6.1.4.1.3808.1.1.6.5.3.1.3INTEGERread-onlymandatory
ePDU2BankStatusTable
OBJECT-TYPE
A table of Rack PDU bank status data
1.3.6.1.4.1.3808.1.1.6.5.4not-accessiblemandatory
ePDU2BankStatusEntry
OBJECT-TYPE
Status data from currently queried Rack PDU bank
1.3.6.1.4.1.3808.1.1.6.5.4.1not-accessiblemandatory
ePDU2BankStatusIndex
OBJECT-TYPE
The index to the Rack PDU bank status table entry.
1.3.6.1.4.1.3808.1.1.6.5.4.1.1INTEGER (1..12)read-onlymandatory
ePDU2BankStatusModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.5.4.1.2INTEGERread-onlymandatory
ePDU2BankStatusNumber
OBJECT-TYPE
The numeric bank ID.
1.3.6.1.4.1.3808.1.1.6.5.4.1.3INTEGERread-onlymandatory
ePDU2BankStatusLoadState
OBJECT-TYPE
Indicates the present load status of the Rack PDU bank being queried.
1.3.6.1.4.1.3808.1.1.6.5.4.1.4INTEGER {normal(1), lowLoad(2), nearOverload(3), overload(4)}read-onlymandatory
ePDU2BankStatusLoad
OBJECT-TYPE
Indicates the current draw, in tenths of Amps, of the load on the Rack PDU bank being queried.
1.3.6.1.4.1.3808.1.1.6.5.4.1.5Gaugeread-onlymandatory
ePDU2BankStatusPeakLoad
OBJECT-TYPE
The peak current of the Rack PDU bank load in tenths of Amps.
1.3.6.1.4.1.3808.1.1.6.5.4.1.6Gaugeread-onlymandatory
ePDU2BankStatusPeakLoadTimestamp
OBJECT-TYPE
Indicates the date and time the bank peak current occurred.
1.3.6.1.4.1.3808.1.1.6.5.4.1.7DisplayStringread-onlymandatory
ePDU2BankStatusPeakLoadStartTime
OBJECT-TYPE
Indicates the date and time of the last bank peak current reset.
1.3.6.1.4.1.3808.1.1.6.5.4.1.8DisplayStringread-onlymandatory
ePDU2Outlet
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.6
ePDU2OutletSwitched
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.6.1
ePDU2OutletSwitchedTableSize
OBJECT-TYPE
The number of switched outlets on connected Rack PDUs.
1.3.6.1.4.1.3808.1.1.6.6.1.1INTEGERread-onlymandatory
ePDU2OutletSwitchedConfigTable
OBJECT-TYPE
A table of Rack PDU switched outlet configuration data.
1.3.6.1.4.1.3808.1.1.6.6.1.2not-accessiblemandatory
ePDU2OutletSwitchedConfigEntry
OBJECT-TYPE
Configuration data from currently queried Rack PDU switched outlet.
1.3.6.1.4.1.3808.1.1.6.6.1.2.1not-accessiblemandatory
ePDU2OutletSwitchedConfigIndex
OBJECT-TYPE
The index to the Rack PDU switched outlet configuration table entry.
1.3.6.1.4.1.3808.1.1.6.6.1.2.1.1INTEGER (1..96)read-onlymandatory
ePDU2OutletSwitchedConfigModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.6.1.2.1.2INTEGERread-onlymandatory
ePDU2OutletSwitchedConfigNumber
OBJECT-TYPE
The numeric switched outlet ID.
1.3.6.1.4.1.3808.1.1.6.6.1.2.1.3INTEGERread-onlymandatory
ePDU2OutletSwitchedConfigName
OBJECT-TYPE
The user-defined switched outlet name string.
1.3.6.1.4.1.3808.1.1.6.6.1.2.1.4DisplayStringread-writemandatory
ePDU2OutletSwitchedConfigPowerOnTime
OBJECT-TYPE
The amount of time (in seconds) the outlet will delay powering on at coldstart or when a command that requires a turn-on delay is issued. Allowed values are: -1 - never power on. 0 - power on immediately. 1 to 7200 - power on up to 7200 seconds after being commanded.
1.3.6.1.4.1.3808.1.1.6.6.1.2.1.5INTEGERread-writemandatory
ePDU2OutletSwitchedConfigPowerOffTime
OBJECT-TYPE
The amount of time (in seconds) the outlet will delay powering off when a command that requires a turn-off delay is issued. Allowed values are: -1 - never power off. 0 - power off immediately. 1 to 7200 - power off up to 7200 seconds after being commanded.
1.3.6.1.4.1.3808.1.1.6.6.1.2.1.6INTEGERread-writemandatory
ePDU2OutletSwitchedConfigRebootDuration
OBJECT-TYPE
During a reboot sequence, power is turned off and then back on. This OID defines the amount of time to wait, in seconds, after turning the power off, at the start of the sequence, before turning power back on, at the end of the reboot sequence. Allowed range is any value between 5 and 60 seconds (1 minute).
1.3.6.1.4.1.3808.1.1.6.6.1.2.1.7INTEGERread-writemandatory
ePDU2OutletSwitchedInfoTable
OBJECT-TYPE
A table of Rack PDU switched outlet information.
1.3.6.1.4.1.3808.1.1.6.6.1.3not-accessiblemandatory
ePDU2OutletSwitchedInfoEntry
OBJECT-TYPE
Information of the currently queried Rack PDU switched outlet.
1.3.6.1.4.1.3808.1.1.6.6.1.3.1not-accessiblemandatory
ePDU2OutletSwitchedInfoIndex
OBJECT-TYPE
The index to the Rack PDU switched outlet information table entry.
1.3.6.1.4.1.3808.1.1.6.6.1.3.1.1INTEGER (1..96)read-onlymandatory
ePDU2OutletSwitchedInfoModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.6.1.3.1.2INTEGERread-onlymandatory
ePDU2OutletSwitchedInfoNumber
OBJECT-TYPE
The numeric switched outlet ID.
1.3.6.1.4.1.3808.1.1.6.6.1.3.1.3INTEGERread-onlymandatory
ePDU2OutletSwitchedInfoName
OBJECT-TYPE
The numeric switched outlet name.
1.3.6.1.4.1.3808.1.1.6.6.1.3.1.4DisplayStringread-onlymandatory
ePDU2OutletSwitchedInfoPhaseLayout
OBJECT-TYPE
This OID describes the phase connections of the referenced outlet as follows: seqPhase1ToNeutral(1) indicates that the outlet is wired from Phase 1 to Neutral. seqPhase2ToNeutral(2) indicates that the outlet is wired from Phase 2 to Neutral. seqPhase3ToNeutral(3) indicates that the outlet is wired from Phase 3 to Neutral. seqPhase1ToPhase2(4) indicates that the outlet is wired from Phase 1 to Phase 2. seqPhase2ToPhase3(5) indicates that the outlet is wired from Phase 2 to Phase 3. seqPhase3ToPhase1(6) indicates that the outlet is wired from Phase 3 to Phase 1.
1.3.6.1.4.1.3808.1.1.6.6.1.3.1.5INTEGERread-onlymandatory
ePDU2OutletSwitchedInfoBank
OBJECT-TYPE
The numeric bank ID.
1.3.6.1.4.1.3808.1.1.6.6.1.3.1.6INTEGERread-onlymandatory
ePDU2OutletSwitchedStatusTable
OBJECT-TYPE
A table of Rack PDU switched outlet status information.
1.3.6.1.4.1.3808.1.1.6.6.1.4not-accessiblemandatory
ePDU2OutletSwitchedStatusEntry
OBJECT-TYPE
Status information for currently queried Rack PDU switched outlet.
1.3.6.1.4.1.3808.1.1.6.6.1.4.1not-accessiblemandatory
ePDU2OutletSwitchedStatusIndex
OBJECT-TYPE
The index to the Rack PDU switched outlet status information table entry.
1.3.6.1.4.1.3808.1.1.6.6.1.4.1.1INTEGER (1..96)read-onlymandatory
ePDU2OutletSwitchedStatusModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.6.1.4.1.2INTEGERread-onlymandatory
ePDU2OutletSwitchedStatusNumber
OBJECT-TYPE
The numeric switched outlet ID.
1.3.6.1.4.1.3808.1.1.6.6.1.4.1.3INTEGERread-onlymandatory
ePDU2OutletSwitchedStatusName
OBJECT-TYPE
The user-defined switched outlet name string.
1.3.6.1.4.1.3808.1.1.6.6.1.4.1.4DisplayStringread-onlymandatory
ePDU2OutletSwitchedStatusState
OBJECT-TYPE
Indicates the present switch state of the Rack PDU switched outlet being queried.
1.3.6.1.4.1.3808.1.1.6.6.1.4.1.5INTEGER {outletStatusOn(1), outletStatusOff(2)}read-onlymandatory
ePDU2OutletSwitchedStatusCommandPending
OBJECT-TYPE
Getting this variable will return the command pending state of the outlet. If a command is pending on the outlet, the outletStatusCommandPending (1) value will be returned. If there is not a command pending on the outlet, the outletStatusNoCommandPending (2) will be returned.
1.3.6.1.4.1.3808.1.1.6.6.1.4.1.6INTEGER {outletStatusCommandPending(1), outletStatusNoCommandPending(2)}read-onlymandatory
ePDU2OutletSwitchedControlTable
OBJECT-TYPE
A table of Rack PDU switched outlet control data.
1.3.6.1.4.1.3808.1.1.6.6.1.5not-accessiblemandatory
ePDU2OutletSwitchedControlEntry
OBJECT-TYPE
Control data for currently queried Rack PDU switched outlet.
1.3.6.1.4.1.3808.1.1.6.6.1.5.1not-accessiblemandatory
ePDU2OutletSwitchedControlIndex
OBJECT-TYPE
The index to the Rack PDU switched outlet control data table entry.
1.3.6.1.4.1.3808.1.1.6.6.1.5.1.1INTEGER (1..96)read-onlymandatory
ePDU2OutletSwitchedControlModuleIndex
OBJECT-TYPE
The user-defined Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.6.1.5.1.2INTEGERread-onlymandatory
ePDU2OutletSwitchedControlNumber
OBJECT-TYPE
The numeric switched outlet ID.
1.3.6.1.4.1.3808.1.1.6.6.1.5.1.3INTEGERread-onlymandatory
ePDU2OutletSwitchedControlName
OBJECT-TYPE
The user-defined switched outlet name string.
1.3.6.1.4.1.3808.1.1.6.6.1.5.1.4DisplayStringread-onlymandatory
ePDU2OutletSwitchedControlCommand
OBJECT-TYPE
Getting this variable will return the outlet state. If the outlet is on, the immediateOn (1) value will be returned. If the outlet is off, the immediateOff (2) value will be returned. Setting this variable to immediateOn (1) will immediately turn the outlet on. Setting this variable to immediateOff (2) will immediately turn the outlet off. Setting this variable to immediateReboot (3) will immediately reboot the outlet. Setting this variable to delayedOn (4) will turn the outlet on after the ePDUOutletConfigPowerOnTime OID time has elapsed. Setting this variable to delayedOff (5) will turn the outlet off after the ePDUOutletConfigPowerOffTime OID time has elapsed. Setting this variable to delayedReboot (6) will cause the Switched Rack PDU to perform a delayedOff command, wait the ePDUOutletConfigRebootDuration OID time, and then perform a delayedOn command. Setting this variable to cancelPendingCommand (7) will cause any pending command to this outlet to be canceled. Setting this variable to outletIdentify (8) will cause PDU LED to display the number of the outlet.
1.3.6.1.4.1.3808.1.1.6.6.1.5.1.5INTEGER {immediateOn(1), immediateOff(2), immediateReboot(3), delayedOn(4), delayedOff(5), delayedReboot(6), cancelPendingCommand(7), outletIdentify(8)}read-writemandatory
ePDU2OutletMetered
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.6.2
ePDU2OutletMeteredTableSize
OBJECT-TYPE
The number of metered outlets on connected Rack PDUs.
1.3.6.1.4.1.3808.1.1.6.6.2.1INTEGERread-onlymandatory
ePDU2OutletMeteredConfigTable
OBJECT-TYPE
A table of Rack PDU metered outlet configuration data.
1.3.6.1.4.1.3808.1.1.6.6.2.2not-accessiblemandatory
ePDU2OutletMeteredConfigEntry
OBJECT-TYPE
Configuration data from currently queried Rack PDU metered outlet.
1.3.6.1.4.1.3808.1.1.6.6.2.2.1not-accessiblemandatory
ePDU2OutletMeteredConfigIndex
OBJECT-TYPE
The index to the Rack PDU metered outlet configuration table entry.
1.3.6.1.4.1.3808.1.1.6.6.2.2.1.1INTEGER (1..96)read-onlymandatory
ePDU2OutletMeteredConfigModuleIndex
OBJECT-TYPE
The user-defined Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.6.2.2.1.2INTEGERread-onlymandatory
ePDU2OutletMeteredConfigNumber
OBJECT-TYPE
The numeric metered outlet ID.
1.3.6.1.4.1.3808.1.1.6.6.2.2.1.3INTEGERread-onlymandatory
ePDU2OutletMeteredConfigName
OBJECT-TYPE
The user-defined metered outlet name string.
1.3.6.1.4.1.3808.1.1.6.6.2.2.1.4DisplayStringread-writemandatory
ePDU2OutletMeteredConfigLowLoadThreshold
OBJECT-TYPE
User-defined outlet low load current threshold in Watts.
1.3.6.1.4.1.3808.1.1.6.6.2.2.1.5INTEGERread-writemandatory
ePDU2OutletMeteredConfigNearOverloadThreshold
OBJECT-TYPE
User-defined outlet near overload warning threshold in Watts.
1.3.6.1.4.1.3808.1.1.6.6.2.2.1.6INTEGERread-writemandatory
ePDU2OutletMeteredConfigOverloadThreshold
OBJECT-TYPE
User-defined outlet overload current threshold in Watts.
1.3.6.1.4.1.3808.1.1.6.6.2.2.1.7INTEGERread-writemandatory
ePDU2OutletMeteredInfoTable
OBJECT-TYPE
A table of Rack PDU metered outlet information.
1.3.6.1.4.1.3808.1.1.6.6.2.3not-accessiblemandatory
ePDU2OutletMeteredInfoEntry
OBJECT-TYPE
Information of currently queried Rack PDU metered outlet.
1.3.6.1.4.1.3808.1.1.6.6.2.3.1not-accessiblemandatory
ePDU2OutletMeteredInfoIndex
OBJECT-TYPE
The index to the Rack PDU metered information table entry.
1.3.6.1.4.1.3808.1.1.6.6.2.3.1.1INTEGER (1..96)read-onlymandatory
ePDU2OutletMeteredInfoModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.6.2.3.1.2INTEGERread-onlymandatory
ePDU2OutletMeteredInfoNumber
OBJECT-TYPE
The numeric metered outlet ID.
1.3.6.1.4.1.3808.1.1.6.6.2.3.1.3INTEGERread-onlymandatory
ePDU2OutletMeteredInfoName
OBJECT-TYPE
The user-defined metered outlet name string.
1.3.6.1.4.1.3808.1.1.6.6.2.3.1.4DisplayStringread-onlymandatory
ePDU2OutletMeteredInfoLayout
OBJECT-TYPE
This OID describes the phase connections of the referenced outlet as follows: seqPhase1ToNeutral(1) indicates that the outlet is wired from Phase 1 to Neutral. seqPhase2ToNeutral(2) indicates that the outlet is wired from Phase 2 to Neutral. seqPhase3ToNeutral(3) indicates that the outlet is wired from Phase 3 to Neutral. seqPhase1ToPhase2(4) indicates that the outlet is wired from Phase 1 to Phase 2. seqPhase2ToPhase3(5) indicates that the outlet is wired from Phase 2 to Phase 3. seqPhase3ToPhase1(6) indicates that the outlet is wired from Phase 3 to Phase 1.
1.3.6.1.4.1.3808.1.1.6.6.2.3.1.5INTEGERread-onlymandatory
ePDU2OutletMeteredInfoRating
OBJECT-TYPE
Maximum power rating of Rack PDU metered outlet.
1.3.6.1.4.1.3808.1.1.6.6.2.3.1.6INTEGERread-onlymandatory
ePDU2OutletMeteredInfoBank
OBJECT-TYPE
This outlet's numeric bank ID.
1.3.6.1.4.1.3808.1.1.6.6.2.3.1.7INTEGERread-onlymandatory
ePDU2OutletMeteredStatusTable
OBJECT-TYPE
A table of Rack PDU metered outlet status data.
1.3.6.1.4.1.3808.1.1.6.6.2.4not-accessiblemandatory
ePDU2OutletMeteredStatusEntry
OBJECT-TYPE
Status data from currently queried Rack PDU metered outlet.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1not-accessiblemandatory
ePDU2OutletMeteredStatusIndex
OBJECT-TYPE
The index to the Rack PDU metered status table entry.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.1INTEGER (1..96)read-onlymandatory
ePDU2OutletMeteredStatusModuleIndex
OBJECT-TYPE
The Rack PDU numeric ID.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.2INTEGERread-onlymandatory
ePDU2OutletMeteredStatusNumber
OBJECT-TYPE
The numeric metered outlet ID.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.3INTEGERread-onlymandatory
ePDU2OutletMeteredStatusName
OBJECT-TYPE
The user-defined metered outlet name string.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.4DisplayStringread-onlymandatory
ePDU2OutletMeteredStatusAlarm
OBJECT-TYPE
Getting this OID will return the current outlet alarm.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.5INTEGER {noLoadAlarm(1), underCurrentAlarm(2), nearOverCurrentAlarm(3), overCurrentAlarm(4)}read-onlymandatory
ePDU2OutletMeteredStatusLoad
OBJECT-TYPE
Getting this OID will return the measured Outlet load for an Outlet Monitored Rack PDU in tenths of Amps.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.6Gaugeread-onlymandatory
ePDU2OutletMeteredStatusActivePower
OBJECT-TYPE
Getting this OID will return the measured Outlet load for an Outlet Monitored Rack PDU in watts.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.7Gaugeread-onlymandatory
ePDU2OutletMeteredStatusPeakPower
OBJECT-TYPE
The peak power consumption of the Rack PDU load in watts.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.8Gaugeread-onlymandatory
ePDU2OutletMeteredStatusPeakPowerTimestamp
OBJECT-TYPE
Get this oid shows the date and time that peak power consumption occurred.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.9DisplayStringread-onlymandatory
ePDU2OutletMeteredStatusPeakPowerStartTime
OBJECT-TYPE
Get this oid shows the date and time that peak power consumption started.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.10DisplayStringread-onlymandatory
ePDU2OutletMeteredStatusEnergy
OBJECT-TYPE
Energy meter measuring Rack PDU load energy consumption in tenths of kilowatt-hours.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.11Gaugeread-onlymandatory
ePDU2OutletMeteredStatusEnergyStart
OBJECT-TYPE
Indicates the date and time of the last device energy meter reset.
1.3.6.1.4.1.3808.1.1.6.6.2.4.1.12DisplayStringread-onlymandatory
ePDU2Sensor
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.7
ePDU2SensorTableSize
OBJECT-TYPE
ePDU2SensorTableSize
1.3.6.1.4.1.3808.1.1.6.7.1INTEGERread-onlymandatory
ePDU2Group
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.6.8
ePDU2GroupNumberOfDevices
OBJECT-TYPE
Getting this OID will return the number of Rack PDU devices contributing to the Daisy Chain group power and energy values. Queries to slave units in an Daisy Chain group will return 0.
1.3.6.1.4.1.3808.1.1.6.8.1INTEGERread-onlymandatory
ePDU2GroupTotalPower
OBJECT-TYPE
Getting this OID will return the total power consumption of the Rack PDU Daisy Chain group devices in watts. Queries to slave units in an Daisy Chain group will return 0.
1.3.6.1.4.1.3808.1.1.6.8.2Gaugeread-onlymandatory
ePDU2GroupTotalEnergy
OBJECT-TYPE
Getting this OID will return the total energy consumption of the Rack PDU Daisy Chain group devices in tenths of kilowatt-hours. To reset the energy meters for each of the Rack PDU devices that contribute to this value, see the ePDU2GroupEnergyReset OID. To view the start time for each of the Rack PDU device energy meters that contribute to this value, see the ePDU2DeviceStatusEnergyStartTime OID. Queries to slave units in an Daisy Chain group will return 0.
1.3.6.1.4.1.3808.1.1.6.8.3Gaugeread-onlymandatory
ePDU2GroupEnergyReset
OBJECT-TYPE
Setting this OID to reset (2) will cause the device energy meter value on each device in the Rack PDU Daisy Chain group to be reset to zero. Getting this OID in models that support this feature will do nothing and return the noOperation(1) value.
1.3.6.1.4.1.3808.1.1.6.8.4INTEGER {noOperation(1), reset(2)}read-writemandatory
ePDU2GroupPeakRecordReset
OBJECT-TYPE
Setting this OID to reset (2) will cause the device peak record value on each device in the Rack PDU Daisy Chain group to be reset to current load/power. Getting this OID in models that support this feature will do nothing and return the noOperation(1) value.
1.3.6.1.4.1.3808.1.1.6.8.5INTEGER {noOperation(1), reset(2)}read-writemandatory
battmgr
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7
bmIdent
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7.1
bmIdentModelName
OBJECT-TYPE
Battery manager model name.
1.3.6.1.4.1.3808.1.1.7.1.1DisplayStringread-onlymandatory
bmIdentHardwareRev
OBJECT-TYPE
Battery manager hardware version.
1.3.6.1.4.1.3808.1.1.7.1.2DisplayStringread-onlymandatory
bmIdentFirmwareRev
OBJECT-TYPE
Battery manager firmware version.
1.3.6.1.4.1.3808.1.1.7.1.3DisplayStringread-onlymandatory
bmIdentLCDHardwareRev
OBJECT-TYPE
Battery manager LCD hardware version.
1.3.6.1.4.1.3808.1.1.7.1.4DisplayStringread-onlymandatory
bmIdentLCDFirmwareRev
OBJECT-TYPE
Battery manager LCD firmware version.
1.3.6.1.4.1.3808.1.1.7.1.5DisplayStringread-onlymandatory
bmIdentDateOfManufacture
OBJECT-TYPE
Battery manager manufacture date.
1.3.6.1.4.1.3808.1.1.7.1.6DisplayStringread-onlymandatory
bmIdentSerialNumber
OBJECT-TYPE
Battery manager serial number.
1.3.6.1.4.1.3808.1.1.7.1.7DisplayStringread-onlymandatory
bmIdentName
OBJECT-TYPE
Battery manager system identification name.
1.3.6.1.4.1.3808.1.1.7.1.8DisplayStringread-writemandatory
bmIdentLocation
OBJECT-TYPE
Battery manager system location.
1.3.6.1.4.1.3808.1.1.7.1.9DisplayStringread-writemandatory
bmProperty
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7.2
bmPropertyStringMax
OBJECT-TYPE
Battery manager max string count supported.
1.3.6.1.4.1.3808.1.1.7.2.1INTEGERread-onlymandatory
bmPropertyMaxProbeOnString
OBJECT-TYPE
Battery manager max probes on a string supported.
1.3.6.1.4.1.3808.1.1.7.2.2INTEGERread-onlymandatory
bmPropertyInputVoltageRange
OBJECT-TYPE
Battery manager line input voltage range.
1.3.6.1.4.1.3808.1.1.7.2.3DisplayStringread-onlymandatory
bmPropertyProbesRating
OBJECT-TYPE
Battery probes model rating.
1.3.6.1.4.1.3808.1.1.7.2.4INTEGER {probeUnknown(1), probe2V(2), probe4V(3), probe6V(4), probe12V(5), probeMixed(6)}read-onlymandatory
bmConfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7.3
bmConfigBattAH
OBJECT-TYPE
Battery manager battery AH type configuration, unit in 0.1 AH.
1.3.6.1.4.1.3808.1.1.7.3.1INTEGERread-writemandatory
bmConfigStringCount
OBJECT-TYPE
Battery manager string count setting.
1.3.6.1.4.1.3808.1.1.7.3.2INTEGERread-writemandatory
bmConfigProbesCountOnString
OBJECT-TYPE
Battery manager probe count on a string setting.
1.3.6.1.4.1.3808.1.1.7.3.3INTEGERread-writemandatory
bmConfigLowVoltAlarmThreshold
OBJECT-TYPE
Battery low voltage alarm threshold setting, unit in 0.1 volt.
1.3.6.1.4.1.3808.1.1.7.3.4INTEGERread-writemandatory
bmConfigHighVoltAlarmThreshold
OBJECT-TYPE
Battery high voltage alarm threshold setting, unit in 0.1 volt.
1.3.6.1.4.1.3808.1.1.7.3.5INTEGERread-writemandatory
bmConfigVoltDiffAlarmThreshold
OBJECT-TYPE
Batteries within a string voltage difference threshold, unit in 0.1 volt.
1.3.6.1.4.1.3808.1.1.7.3.6INTEGERread-writemandatory
bmConfigLowTempAlarmThreshold
OBJECT-TYPE
Battery low temperature alarm threshold, unit in 0.1 degree C.
1.3.6.1.4.1.3808.1.1.7.3.7INTEGERread-writemandatory
bmConfigHighTempAlarmThreshold
OBJECT-TYPE
Battery high temperature alarm threshold, unit in 0.1 degree C.
1.3.6.1.4.1.3808.1.1.7.3.8INTEGERread-writemandatory
bmConfigLowResAlarmThreshold
OBJECT-TYPE
Battery low resistance alarm threshold, unit in 0.01 mOhm.
1.3.6.1.4.1.3808.1.1.7.3.9INTEGERread-writemandatory
bmConfigHighResAlarmThreshold
OBJECT-TYPE
Battery high resistance alarm threshold, unit in 0.01 mOhm.
1.3.6.1.4.1.3808.1.1.7.3.10INTEGERread-writemandatory
bmConfigLowResWarnThreshold
OBJECT-TYPE
Battery low resistance warning threshold, unit in 0.01 mOhm.
1.3.6.1.4.1.3808.1.1.7.3.11INTEGERread-writemandatory
bmConfigHighResWarnThreshold
OBJECT-TYPE
Battery high resistance warning threshold, unit in 0.01 mOhm.
1.3.6.1.4.1.3808.1.1.7.3.12INTEGERread-writemandatory
bmConfigResHealthAlarmThreshold
OBJECT-TYPE
Battery resistance health alarm threshold, unit in percentage and should larger than 100.
1.3.6.1.4.1.3808.1.1.7.3.13INTEGERread-writemandatory
bmConfigResHealthWarnThreshold
OBJECT-TYPE
Battery resistance health warn threshold, unit in percentage and should larger than 100.
1.3.6.1.4.1.3808.1.1.7.3.14INTEGERread-writemandatory
bmConfigLowVoltAlarmThreshold10mV
OBJECT-TYPE
Battery low voltage alarm threshold setting, unit in 10 mV (0.01 volt).
1.3.6.1.4.1.3808.1.1.7.3.15INTEGERread-writemandatory
bmConfigHighVoltAlarmThreshold10mV
OBJECT-TYPE
Battery high voltage alarm threshold setting, unit in 10 mV (0.01 volt).
1.3.6.1.4.1.3808.1.1.7.3.16INTEGERread-writemandatory
bmConfigMergeFeature
OBJECT-TYPE
String merge feature setting.
1.3.6.1.4.1.3808.1.1.7.3.17INTEGER {enable(1), disable(2)}read-writemandatory
bmControl
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7.4
bmControlSysytemIdenticator
OBJECT-TYPE
Battery manager will perform a panel indicator test when the variable is set to testIndicators(2). Get this oid will get noTestIndicators(1).
1.3.6.1.4.1.3808.1.1.7.4.1INTEGER {noTestIndicators(1), testIndicators(2)}read-writemandatory
bmControlProbeIndicator
OBJECT-TYPE
Battery manager will perform a probe indicator test when the variable is set to testIndicators(2). Get this oid will get noTestIndicators(1).
1.3.6.1.4.1.3808.1.1.7.4.2INTEGER {noTestIndicators(1), testIndicators(2)}read-writemandatory
bmProbes
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7.5
bmProbesNum
OBJECT-TYPE
Current connected probe number.
1.3.6.1.4.1.3808.1.1.7.5.1INTEGERread-onlymandatory
bmProbesTableSize
OBJECT-TYPE
Current configured probe number.
1.3.6.1.4.1.3808.1.1.7.5.2INTEGERread-onlymandatory
bmProbesTable
OBJECT-TYPE
Allows for getting of status of probes.
1.3.6.1.4.1.3808.1.1.7.5.3not-accessiblemandatory
bmProbesEntry
OBJECT-TYPE
The status of probes installation to gather status from.
1.3.6.1.4.1.3808.1.1.7.5.3.1not-accessiblemandatory
bmProbesIndex
OBJECT-TYPE
Probes table index
1.3.6.1.4.1.3808.1.1.7.5.3.1.1INTEGER (1..960)read-onlymandatory
bmProbesPackIndex
OBJECT-TYPE
The battery pack number the probe installed.
1.3.6.1.4.1.3808.1.1.7.5.3.1.2INTEGER (1..64)read-onlymandatory
bmProbesStringIndex
OBJECT-TYPE
The string number the probe installed.
1.3.6.1.4.1.3808.1.1.7.5.3.1.3INTEGER (1..16)read-onlymandatory
bmProbesBattIndex
OBJECT-TYPE
The battery number the probe installed.
1.3.6.1.4.1.3808.1.1.7.5.3.1.4INTEGER (1..960)read-onlymandatory
bmProbesVoltageTableSize
OBJECT-TYPE
The size of the battery voltage table
1.3.6.1.4.1.3808.1.1.7.5.4INTEGERread-onlymandatory
bmProbesVoltageTable
OBJECT-TYPE
Allows for getting of voltage of batteries.
1.3.6.1.4.1.3808.1.1.7.5.5not-accessiblemandatory
bmProbesVoltageEntry
OBJECT-TYPE
Batteries voltage status.
1.3.6.1.4.1.3808.1.1.7.5.5.1not-accessiblemandatory
bmProbesVoltageIndex
OBJECT-TYPE
The index of the voltage status entry.
1.3.6.1.4.1.3808.1.1.7.5.5.1.1INTEGER (1..960)read-onlymandatory
bmProbesVoltagePackIndex
OBJECT-TYPE
The battery pack index to the voltage record.
1.3.6.1.4.1.3808.1.1.7.5.5.1.2INTEGER (1..64)read-onlymandatory
bmProbesVoltageStringIndex
OBJECT-TYPE
The battery string index to the voltage record.
1.3.6.1.4.1.3808.1.1.7.5.5.1.3INTEGER (1..16)read-onlymandatory
bmProbesVoltageBattIndex
OBJECT-TYPE
The battery index to the voltage record within its string.
1.3.6.1.4.1.3808.1.1.7.5.5.1.4INTEGER (1..960)read-onlymandatory
bmProbesVoltageProbeIndex
OBJECT-TYPE
The probe index to the voltage record.
1.3.6.1.4.1.3808.1.1.7.5.5.1.5INTEGER (1..960)read-onlymandatory
bmProbesVoltageAlarmStatus
OBJECT-TYPE
The battery voltage alarm status.
1.3.6.1.4.1.3808.1.1.7.5.5.1.6INTEGER {voltageNormal(1), voltageWarnLow(2), voltageWarnHigh(3), voltageAlarmLow(4), voltageAlarmHigh(5)}read-onlymandatory
bmProbesVoltage
OBJECT-TYPE
Getting this oid to get battery voltage, unit in 10mV (0.01 volt).
1.3.6.1.4.1.3808.1.1.7.5.5.1.7INTEGERread-onlymandatory
bmProbesVoltageEqualPercentage
OBJECT-TYPE
Getting this oid to get battery voltage equalizing power, unit in percentage.
1.3.6.1.4.1.3808.1.1.7.5.5.1.8INTEGERread-onlymandatory
bmProbesTempTableSize
OBJECT-TYPE
The size of the Temperature table
1.3.6.1.4.1.3808.1.1.7.5.6INTEGERread-onlymandatory
bmProbesTempTable
OBJECT-TYPE
Allows for getting of temperature of probes.
1.3.6.1.4.1.3808.1.1.7.5.7not-accessiblemandatory
bmProbesTempEntry
OBJECT-TYPE
Temperature status entry.
1.3.6.1.4.1.3808.1.1.7.5.7.1not-accessiblemandatory
bmProbesTempIndex
OBJECT-TYPE
The index of the temperature entry.
1.3.6.1.4.1.3808.1.1.7.5.7.1.1INTEGER (1..960)read-onlymandatory
bmProbesTempPackIndex
OBJECT-TYPE
The battery pack index of the temperature entry.
1.3.6.1.4.1.3808.1.1.7.5.7.1.2INTEGER (1..64)read-onlymandatory
bmProbesTempStringIndex
OBJECT-TYPE
The index to the string.
1.3.6.1.4.1.3808.1.1.7.5.7.1.3INTEGER (1..16)read-onlymandatory
bmProbesTempBattIndex
OBJECT-TYPE
The index to the battery.
1.3.6.1.4.1.3808.1.1.7.5.7.1.4INTEGER (1..960)read-onlymandatory
bmProbesTempProbeIndex
OBJECT-TYPE
The index to the probe.
1.3.6.1.4.1.3808.1.1.7.5.7.1.5INTEGER (1..960)read-onlymandatory
bmProbesTempAlarmStatus
OBJECT-TYPE
The alarm status of the temperature.
1.3.6.1.4.1.3808.1.1.7.5.7.1.6INTEGER {temperatureNormal(1), temperatureWarnLow(2), temperatureWarnHigh(3), temperatureAlarmLow(4), temperatureAlarmHigh(5)}read-onlymandatory
bmProbesTemperature
OBJECT-TYPE
The temperature record, measure in 0.1 degree C.
1.3.6.1.4.1.3808.1.1.7.5.7.1.7INTEGER (-40..60)read-onlymandatory
bmProbesResTableSize
OBJECT-TYPE
The size of the Resistance table
1.3.6.1.4.1.3808.1.1.7.5.8INTEGERread-onlymandatory
bmProbesResTable
OBJECT-TYPE
Allows for getting of resistance of probes.
1.3.6.1.4.1.3808.1.1.7.5.9not-accessiblemandatory
bmProbesResEntry
OBJECT-TYPE
The resistance status entry.
1.3.6.1.4.1.3808.1.1.7.5.9.1not-accessiblemandatory
bmProbesResIndex
OBJECT-TYPE
The index of the resistance entry.
1.3.6.1.4.1.3808.1.1.7.5.9.1.1INTEGER (1..960)read-onlymandatory
bmProbesResPackIndex
OBJECT-TYPE
The battery pack index to the resistance entry.
1.3.6.1.4.1.3808.1.1.7.5.9.1.2INTEGER (1..64)read-onlymandatory
bmProbesResStringIndex
OBJECT-TYPE
The index to the string.
1.3.6.1.4.1.3808.1.1.7.5.9.1.3INTEGER (1..16)read-onlymandatory
bmProbesResBattIndex
OBJECT-TYPE
The index to the battery.
1.3.6.1.4.1.3808.1.1.7.5.9.1.4INTEGER (1..960)read-onlymandatory
bmProbesResProbeIndex
OBJECT-TYPE
The index to the probe.
1.3.6.1.4.1.3808.1.1.7.5.9.1.5INTEGER (1..960)read-onlymandatory
bmProbesResAlarmStatus
OBJECT-TYPE
The alarm status of the battery resistance.
1.3.6.1.4.1.3808.1.1.7.5.9.1.6INTEGER {resistanceNormal(1), resistanceWarnLow(2), resistanceWarnHigh(3), resistanceAlarmLow(4), resistanceAlarmHigh(5)}read-onlymandatory
bmProbesResistance
OBJECT-TYPE
The resistance of the battery, unit in 0.01 mOhm.
1.3.6.1.4.1.3808.1.1.7.5.9.1.7INTEGER (-40..60)read-onlymandatory
bmProbesResHealth
OBJECT-TYPE
The resistance health status, unit in percentage.
1.3.6.1.4.1.3808.1.1.7.5.9.1.8INTEGER (-40..60)read-onlymandatory
bmFuncRes
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7.6
bmFuncResMeasure
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7.6.1
bmFuncResMeasureInterval
OBJECT-TYPE
The time interval for battery manager to exercising resistance measurement, unit in hour(s).
1.3.6.1.4.1.3808.1.1.7.6.1.1INTEGERread-writemandatory
bmFuncResMeasureManualCmd
OBJECT-TYPE
This oid allows user to manual resistance measurement. Set this oid to measureResNow(2) to measure resistance immediately. Get bmFuncResMeasureLastCmdResult oid to check command acceptance.
1.3.6.1.4.1.3808.1.1.7.6.1.2INTEGER {noResMeasure(1), resMeasureNow(2)}read-writemandatory
bmFuncResMeasureManualResult
OBJECT-TYPE
Get this oid to confirm the last manual command result.
1.3.6.1.4.1.3808.1.1.7.6.1.3INTEGER {resNoManualResult(1), resManualProcessing(2), resManualComplete(3), resManualReject(9)}read-onlymandatory
bmFuncResMeasureLastUpdate
OBJECT-TYPE
When resistance measurement complete either by auto or manual, this oid will update to the last update time.
1.3.6.1.4.1.3808.1.1.7.6.1.4DisplayStringread-onlymandatory
bmFuncEqual
OBJECT-IDENTITY
1.3.6.1.4.1.3808.1.1.7.7
bmFuncEqualEnable
OBJECT-TYPE
Battery voltage equalization configuration.
1.3.6.1.4.1.3808.1.1.7.7.1INTEGER {enable(1), disable(2)}read-writemandatory
bmFuncEqualActiveCond
OBJECT-TYPE
Volatge equalization will active when the voltage difference larger than this value, unit in 10mV.
1.3.6.1.4.1.3808.1.1.7.7.2INTEGERread-writemandatory
bmFuncEqualStatus
OBJECT-TYPE
This oid shows the current equalization status.
1.3.6.1.4.1.3808.1.1.7.7.3INTEGER {equalActive(1), equalFailed(2), equalNotActive(3), equalNotSupport(9)}read-onlymandatory
bmFuncEqualStartTime
OBJECT-TYPE
This oid shows the last equalization start time.
1.3.6.1.4.1.3808.1.1.7.7.4DisplayStringread-onlymandatory
bmFuncEqualElapseTime
OBJECT-TYPE
This oid shows the elapsed time since last equalization started.
1.3.6.1.4.1.3808.1.1.7.7.5TimeTicksread-onlymandatory
cpsmgmt
OBJECT-IDENTITY
1.3.6.1.4.1.3808.2
mconfig
OBJECT-IDENTITY
1.3.6.1.4.1.3808.2.1
mconfigNumTrapAccepters
OBJECT-TYPE
The number of receivers to send traps to.
1.3.6.1.4.1.3808.2.1.1INTEGERread-onlymandatory
mconfigTrapAccepterTable
OBJECT-TYPE
A list of receivers to send traps to. The numbers of entries are given by the value of mconfigNumTrapAccepters.
1.3.6.1.4.1.3808.2.1.2not-accessiblemandatory
mconfigTrapAccepterEntry
OBJECT-TYPE
The receivers to send traps to.
1.3.6.1.4.1.3808.2.1.2.1not-accessiblemandatory
trapIndex
OBJECT-TYPE
The trap receiver entry index.
1.3.6.1.4.1.3808.2.1.2.1.1INTEGER (1..10)not-accessiblemandatory
accepterAddr
OBJECT-TYPE
The trap receiver IP address.
1.3.6.1.4.1.3808.2.1.2.1.2IpAddressread-writemandatory
communityString
OBJECT-TYPE
The trap receiver community name.
1.3.6.1.4.1.3808.2.1.2.1.3DisplayStringread-writemandatory
severityDegree
OBJECT-TYPE
The trap receiver severity level. Traps are marked in severity level as informational(1), warning(2), severe(3). Only send the traps of equal or greater severity than this value to the receiver.
1.3.6.1.4.1.3808.2.1.2.1.4INTEGER {information(1), warning(2), severe(3)}read-onlymandatory
accepterActive
OBJECT-TYPE
A receiver will accept traps if yes, and none if no.
1.3.6.1.4.1.3808.2.1.2.1.5INTEGER {yes(1), no(2)}read-writemandatory
mconfigDHCPEnabled
OBJECT-TYPE
The system will automatically obtain its IP from a DHCP server if yes, and none if no.
1.3.6.1.4.1.3808.2.1.3INTEGER {yes(1), no(2)}read-writemandatory
mconfigMyAddr
OBJECT-TYPE
The system IP address.
1.3.6.1.4.1.3808.2.1.4IpAddressread-onlymandatory
mconfigClock
OBJECT-IDENTITY
1.3.6.1.4.1.3808.2.1.5
mconfigClockDate
OBJECT-TYPE
The current date in the mm/dd/yyyy format. Example: 01/01/2000.
1.3.6.1.4.1.3808.2.1.5.1DisplayStringread-writemandatory
mconfigClockTime
OBJECT-TYPE
The current time in the hh:mm:ss 24H format.
1.3.6.1.4.1.3808.2.1.5.2DisplayStringread-writemandatory
mtrapinfo
OBJECT-IDENTITY
1.3.6.1.4.1.3808.2.2
mtrapinfoInteger
OBJECT-TYPE
Allow CPS traps with an integer argument for providing detail information. Not being defined in the MIB, only reply 0.
1.3.6.1.4.1.3808.2.2.1INTEGERread-onlymandatory
mtrapinfoIpAddress
OBJECT-TYPE
Allow CPS traps with an IP address argument for providing detail information. Not being defined in the MIB, only reply 0.0.0.0.
1.3.6.1.4.1.3808.2.2.2IpAddressread-onlymandatory
mtrapinfoString
OBJECT-TYPE
Allow CPS traps with an octet string argument for providing detail information. Not being defined in the MIB, only reply a NULL string.
1.3.6.1.4.1.3808.2.2.3DisplayStringread-onlymandatory
mtrapinfoGauge
OBJECT-TYPE
Allow CPS traps with an Gauge argument for providing detail information. Not being defined in the MIB, only reply 0.
1.3.6.1.4.1.3808.2.2.4Gaugeread-onlymandatory
mtrapinfoTimeTicks
OBJECT-TYPE
Allow CPS traps with an TimeTicks argument for providing detail information. Not being defined in the MIB, only reply 0.
1.3.6.1.4.1.3808.2.2.5TimeTicksread-onlymandatory
mtrapinfoBmEventId
OBJECT-TYPE
Allow CPS traps with an integer argument for providing detail information about Battery Manager specific event identifier. Not being defined in the MIB, only reply 0. Known Specific Event ID: Battery Manager 0 - not used 1 - Alarm: The battery manager system fault. 2 - Info: Device configuration changed. 3 - Alarm: Probe configuration mismatched. 4 - Info: Probe configuration matched. 5 - Alarm: Communication with battery manager has been lost. 6 - Info: Communication with battery manager has been restored. 7 - Alarm: Communication with LCD has been lost. 8 - Info: Communication with LCD has been restored. 9 - Warning: Enter battery equalization active mode. 10- Warning: Leave battery equalization active mode. 11- Alarm: Battery equalizing has failed. 12- Info: Battery equalizing succeed. Known Specific Event ID: Battery Probes 101 - Alarm: Low battery voltage. 102 - Alarm: High battery voltage. 103 - Info: Battery voltage event has cleared. 104 - Alarm: Low battery temperature. 105 - Alarm: High battery temperature. 106 - Info: Battery temperature event has cleared. 107 - Alarm: Critical low battery resistance. 108 - Alarm: Critical high battery resistance. 109 - Warning: Low battery resistance. 110 - Warning: high battery resistance. 111 - Info: Battery resistance event has cleared. 112 - Alarm: Battery resistance health has crossed alarm threshold. 113 - Warning: Battery resistance health has crossed warning threshold. 114 - Info: Battery resistance health has returned to Normal.
1.3.6.1.4.1.3808.2.2.6INTEGERread-onlymandatory
mcontrol
OBJECT-IDENTITY
1.3.6.1.4.1.3808.2.3
mcontrolRestart
OBJECT-TYPE
Setting this OID to restartCurrentSystem (2) will restart the current system. Setting this OID to restartCurrentAgent (3) will restart the current agent. Setting this OID to restartCurrentSystemAnd Agent (4) will restart the current the current system and agent.
1.3.6.1.4.1.3808.2.3.1INTEGER {none(1), restartCurrentSystem(2), restartCurrentAgent(3), restartCurrentSystemAndAgent(4)}read-writemandatory
mcontrolReset
OBJECT-TYPE
Setting this OID to resetCurrentSystem (2) will reset the current system. Setting this OID to resetCurrentAgent (3) will reset the current agent. Setting this OID to resetCurrentSystemAndAgenta (4) will reset the current system and the current agent.
1.3.6.1.4.1.3808.2.3.2INTEGER {none(1), resetCurrentSystem(2), resetCurrentAgent(3), resetCurrentSystemAndAgent(4)}read-writemandatory

Notifications

NameOIDStatus
communicationLost
NOTIFICATION-TYPE
SEVERE: Communication with the UPS has been lost.
1.3.6.1.4.1.3808.0.1
upsOverload
NOTIFICATION-TYPE
SEVERE: The UPS has sensed an overload condition.
1.3.6.1.4.1.3808.0.2
upsDiagnosticsFailed
NOTIFICATION-TYPE
SEVERE: The UPS battery test failed.
1.3.6.1.4.1.3808.0.3
upsDischarged
NOTIFICATION-TYPE
SEVERE: The UPS has started a runtime estimation process.
1.3.6.1.4.1.3808.0.4
upsOnBattery
NOTIFICATION-TYPE
WARNING: Utility power failed, transfer to backup mode.
1.3.6.1.4.1.3808.0.5
upsBoostOn
NOTIFICATION-TYPE
WARNING: The UPS has enabled boost, low utility voltage.
1.3.6.1.4.1.3808.0.6
lowBattery
NOTIFICATION-TYPE
SEVERE: The UPS battery capacity is low than threshold, soon to be exhausted.
1.3.6.1.4.1.3808.0.7
communicationEstablished
NOTIFICATION-TYPE
INFORMATIONAL: Communication to the UPS has been established.
1.3.6.1.4.1.3808.0.8
powerRestored
NOTIFICATION-TYPE
INFORMATIONAL: Utility power restored, return from backup mode.
1.3.6.1.4.1.3808.0.9
upsDiagnosticsPassed
NOTIFICATION-TYPE
INFORMATIONAL: The UPS battery test passed.
1.3.6.1.4.1.3808.0.10
returnFromLowBattery
NOTIFICATION-TYPE
INFORMATIONAL: The UPS has returned from a low battery condition.
1.3.6.1.4.1.3808.0.11
upsTurnedOff
NOTIFICATION-TYPE
WARNING: The UPS has been turned off.
1.3.6.1.4.1.3808.0.12
upsSleeping
NOTIFICATION-TYPE
WARNING: The UPS entered sleep mode. Output power will not be provided.
1.3.6.1.4.1.3808.0.13
upsWokeUp
NOTIFICATION-TYPE
INFORMATION: The UPS woke up from sleep mode. Output power is being provided.
1.3.6.1.4.1.3808.0.14
upsRebootStarted
NOTIFICATION-TYPE
WARNING: The UPS started reboot sequence.
1.3.6.1.4.1.3808.0.15
upsOverTemp
NOTIFICATION-TYPE
SEVERE: The UPS inner temperature is too high.
1.3.6.1.4.1.3808.0.16
returnFromOverTemp
NOTIFICATION-TYPE
INFORMATIONAL: The UPS over temperature condition cleared.
1.3.6.1.4.1.3808.0.17
upsBuckOn
NOTIFICATION-TYPE
WARNING: The UPS has enabled buck, high utility voltage.
1.3.6.1.4.1.3808.0.18
returnFromOverLoad
NOTIFICATION-TYPE
INFORMATIONAL: The UPS has returned from an overload condition.
1.3.6.1.4.1.3808.0.19
returnFromDischarged
NOTIFICATION-TYPE
INFORMATIONAL: The UPS runtime estimation completed.
1.3.6.1.4.1.3808.0.20
upsScheduleShutdown
NOTIFICATION-TYPE
WARNING: The UPS has started its schedule shutdown sequence.
1.3.6.1.4.1.3808.0.21
upsEnterSleep
NOTIFICATION-TYPE
WARNING: The UPS started sleep sequence.
1.3.6.1.4.1.3808.0.22
upsChargerFailure
NOTIFICATION-TYPE
WARNING: The battery charger is abnormal.
1.3.6.1.4.1.3808.0.23
returnFromChargerFailure
NOTIFICATION-TYPE
INFORMATIONAL: The charger returned from a failure condition.
1.3.6.1.4.1.3808.0.24
upsTurnoffStarted
NOTIFICATION-TYPE
WARNING: The UPS started turn off sequence.
1.3.6.1.4.1.3808.0.25
upsTurnedOn
NOTIFICATION-TYPE
WARNING: The UPS has been turned on.
1.3.6.1.4.1.3808.0.26
upsRemoteCommandFailed
NOTIFICATION-TYPE
WARNING: The UPS remote command failed.
1.3.6.1.4.1.3808.0.27
upsLostRedundant
NOTIFICATION-TYPE
WARNING: Not enough power redundancy modules.
1.3.6.1.4.1.3808.0.28
upsSignalClientShutdown
NOTIFICATION-TYPE
SEVERE: The UPS has signaled clients to shutdown.
1.3.6.1.4.1.3808.0.29
upsEmergencyPowerOff
NOTIFICATION-TYPE
Emergency Power Off (EPO)
1.3.6.1.4.1.3808.0.30
nclBankOn
NOTIFICATION-TYPE
INFORMATIONAL: Non-Critical bank has been turned on.
1.3.6.1.4.1.3808.0.31
nclBankOff
NOTIFICATION-TYPE
INFORMATIONAL: Non-Critical bank has been turned off.
1.3.6.1.4.1.3808.0.32
upsCommandCancel
NOTIFICATION-TYPE
INFORMATION: The cancel command has been executed.
1.3.6.1.4.1.3808.0.33
upsStartBatteryTest
NOTIFICATION-TYPE
INFORMATION: The UPS has started a battery test process.
1.3.6.1.4.1.3808.0.34
upsRemainRuntimeLowThanThreshold
NOTIFICATION-TYPE
WARNING: The UPS remaining runtime is lower than threshold.
1.3.6.1.4.1.3808.0.35
nclBankStartScheduleOff
NOTIFICATION-TYPE
INFORMATION: Non-Critial bank has started its schedule off sequence.
1.3.6.1.4.1.3808.0.36
upsEstimationAbort
NOTIFICATION-TYPE
WARNING: The UPS runtime estimation aborted.
1.3.6.1.4.1.3808.0.37
upsHardwareFault
NOTIFICATION-TYPE
WARNING: The UPS hardware fault.
1.3.6.1.4.1.3808.0.38
upsBatteryNotPresent
NOTIFICATION-TYPE
WARNING: Battery is not present.
1.3.6.1.4.1.3808.0.39
upsWiringFault
NOTIFICATION-TYPE
WARNING: The UPS wiring fault has been detected.
1.3.6.1.4.1.3808.0.40
upsWiringFaultCleared
NOTIFICATION-TYPE
INFORMATION: The UPS wiring fault has been cleared.
1.3.6.1.4.1.3808.0.41
upsEnterBypassMode
NOTIFICATION-TYPE
WARNING: The UPS enters bypass mode.
1.3.6.1.4.1.3808.0.42
upsReturnFromBypassMode
NOTIFICATION-TYPE
INFORMATION: The UPS leaves bypass mode.
1.3.6.1.4.1.3808.0.43
upsBypassOverload
NOTIFICATION-TYPE
WARNING: The UPS bypass overload.
1.3.6.1.4.1.3808.0.44
upsBypassOverloadCleared
NOTIFICATION-TYPE
INFORMATION: The UPS bypass overload has been cleared.
1.3.6.1.4.1.3808.0.45
upsEnterECOMode
NOTIFICATION-TYPE
WARNING: The UPS enters ECO mode.
1.3.6.1.4.1.3808.0.46
upsReturnFromECOMode
NOTIFICATION-TYPE
WARNING: The UPS leaves ECO mode.
1.3.6.1.4.1.3808.0.47
upsBatteryOverThreeYear
NOTIFICATION-TYPE
WARNING: Battery has been 3 years from last Replacement.
1.3.6.1.4.1.3808.0.48
upsBatteryExpiration
NOTIFICATION-TYPE
WARNING: The battery may not work well anymore.
1.3.6.1.4.1.3808.0.49
upsBatteryReplacement
NOTIFICATION-TYPE
WARNING: The battery has been replaced.
1.3.6.1.4.1.3808.0.50
upsModuleInvertorAlarm
NOTIFICATION-TYPE
WARNING: The UPS module invertor alarm.
1.3.6.1.4.1.3808.0.51
upsModuleRectifierAlarm
NOTIFICATION-TYPE
WARNING: The UPS module rectifier alarm.
1.3.6.1.4.1.3808.0.52
upsModuleFanAlarm
NOTIFICATION-TYPE
WARNING: The UPS module fan alarm.
1.3.6.1.4.1.3808.0.53
upsModuleManualShutdown
NOTIFICATION-TYPE
WARNING: The UPS module manual shutdown.
1.3.6.1.4.1.3808.0.54
upsModuleOverload
NOTIFICATION-TYPE
WARNING: The UPS module overload.
1.3.6.1.4.1.3808.0.55
upsFirmwareUpgradeStart
NOTIFICATION-TYPE
WARNING: UPS firmware starts to update.
1.3.6.1.4.1.3808.0.56
upsFirmwareUpgradeEnd
NOTIFICATION-TYPE
WARNING: UPS firmware update is over.
1.3.6.1.4.1.3808.0.57
upsRFC1628TrapOnBattery
NOTIFICATION-TYPE
WARNING: RFC1628: UPS is on battery.
1.3.6.1.4.1.3808.0.58
upsRFC1628TrapTestCompleted
NOTIFICATION-TYPE
WARNING: RFC1628: UPS test completed.
1.3.6.1.4.1.3808.0.59
upsRFC1628TrapAlarmEntryAdded
NOTIFICATION-TYPE
WARNING: RFC1628: Alarm entry added.
1.3.6.1.4.1.3808.0.60
failAuthViaHTTP
NOTIFICATION-TYPE
WARNING: Login authorization failure via HTTP.
1.3.6.1.4.1.3808.0.61
passwordChange
NOTIFICATION-TYPE
INFORMATION: The password has been changed.
1.3.6.1.4.1.3808.0.62
failAuthViaConsole
NOTIFICATION-TYPE
WARNING: Login authorization failure via Console.
1.3.6.1.4.1.3808.0.63
configFileUpload
NOTIFICATION-TYPE
INFORMATION: Configuration file uploaded.
1.3.6.1.4.1.3808.0.64
adminLoginInfo
NOTIFICATION-TYPE
INFORMATION: Administrator login.
1.3.6.1.4.1.3808.0.65
adminLogoutInfo
NOTIFICATION-TYPE
INFORMATION: Administrator logout.
1.3.6.1.4.1.3808.0.66
deviceLoginInfo
NOTIFICATION-TYPE
INFORMATION: Device login.
1.3.6.1.4.1.3808.0.67
deviceLogoutInfo
NOTIFICATION-TYPE
INFORMATION: Device logout.
1.3.6.1.4.1.3808.0.68
configurationChanged
NOTIFICATION-TYPE
INFORMATION: Configuration has been changed.
1.3.6.1.4.1.3808.0.69
clientRegistered
NOTIFICATION-TYPE
Information: PowerPanel client has been registered.
1.3.6.1.4.1.3808.0.70
clientRemoved
NOTIFICATION-TYPE
Information: PowerPanel client has been removed.
1.3.6.1.4.1.3808.0.71
testEvent
NOTIFICATION-TYPE
Information: Test Event.
1.3.6.1.4.1.3808.0.72
outletUserLoginInfo
NOTIFICATION-TYPE
Information: Outlet User login.
1.3.6.1.4.1.3808.0.73
outletUserLogoutInfo
NOTIFICATION-TYPE
Information: Outlet User logout.
1.3.6.1.4.1.3808.0.74
ePDUCommunicationEstablished
NOTIFICATION-TYPE
INFORMATIONAL: Communication with a Rack PDU has been established. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.100
ePDUCommunicationLost
NOTIFICATION-TYPE
SEVERE: Communication with a Rack PDU has been lost. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.101
ePDUOutletOn
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on a Switched Rack PDU has turned on. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.102
ePDUOutletOff
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on a Switched Rack PDU has turned off. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.103
ePDUDeviceConfigChange
NOTIFICATION-TYPE
INFORMATIONAL: A device configuration change has been made on a Rack PDU. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.104
ePDUOutletConfigChange
NOTIFICATION-TYPE
INFORMATIONAL: An outlet configuration change has been made on a Switched Rack PDU. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.105
ePDULowLoad
NOTIFICATION-TYPE
WARNING: A Rack PDU has violated the low load threshold. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.106
ePDULowLoadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The low load condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.107
ePDUNearOverload
NOTIFICATION-TYPE
WARNING: A Rack PDU is near an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.108
ePDUNearOverloadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The near overload condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.109
ePDUOverload
NOTIFICATION-TYPE
SEVERE: A Rack PDU is in an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.110
ePDUOverloadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The overload condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.111
ePDUDelayOutletOnCommand
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on a Switched Rack PDU has been assigned to turn on. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.112
ePDUDelayOutletOffCommand
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on a Switched Rack PDU has been assigned to turn off. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.113
ePDUDelayOutletRebootCommand
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on a Switched Rack PDU has been assigned to reboot. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.114
ePDUCancelPendingCommand
NOTIFICATION-TYPE
INFORMATIONAL: A cancel pending command has been made on a Switched Rack PDU. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number (0 indicates all outlets). The fourth argument is the outlet name (or device name if all outlets).
1.3.6.1.4.1.3808.0.115
ePDULineUndervoltage
NOTIFICATION-TYPE
SEVERE: Utility Line Undervoltage The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.116
ePDULineUndervoltageCleared
NOTIFICATION-TYPE
INFORMATIONAL: Utility Line Undervoltage Cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.117
ePDULineOvervoltage
NOTIFICATION-TYPE
SEVERE: Utility Line Overvoltage. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.118
ePDULineOvervoltageCleared
NOTIFICATION-TYPE
INFORMATIONAL: Utility Line Overvoltage Cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase number.
1.3.6.1.4.1.3808.0.119
ePDUPowerSupply1Fail
NOTIFICATION-TYPE
SEVERE: Power Supply 1 on Rack PDU is in FAIL state. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.120
ePDUPowerSupply1Ok
NOTIFICATION-TYPE
INFORMATIONAL: Power Supply 1 on Rack PDU is operating normally. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.121
ePDUPowerSupply2Fail
NOTIFICATION-TYPE
SEVERE: Power Supply 2 on Rack PDU is in FAIL state. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.122
ePDUPowerSupply2Ok
NOTIFICATION-TYPE
INFORMATIONAL: Power Supply 2 on Rack PDU is operating normally. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.123
ePDUBankLowLoad
NOTIFICATION-TYPE
WARNING: A Rack PDU bank has violated the low load threshold. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
1.3.6.1.4.1.3808.0.124
ePDUBankLowLoadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The low load condition on a Rack PDU bank has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
1.3.6.1.4.1.3808.0.125
ePDUBankNearOverload
NOTIFICATION-TYPE
WARNING: A Rack PDU bank is near an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
1.3.6.1.4.1.3808.0.126
ePDUBankNearOverloadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The near overload condition on a Rack PDU bank has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase/bank number.
1.3.6.1.4.1.3808.0.127
ePDUBankOverload
NOTIFICATION-TYPE
SEVERE: A Rack PDU bank is in an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
1.3.6.1.4.1.3808.0.128
ePDUBankOverloadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The overload condition on a Rack PDU bank has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the bank number.
1.3.6.1.4.1.3808.0.129
ePDUComponentCommunicationEstablished
NOTIFICATION-TYPE
INFORMATIONAL: Component communication lost has been cleared. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.130
ePDUComponentCommunicationLost
NOTIFICATION-TYPE
SEVERE: Component communication lost. The first argument is the serial number. The second argument is the device name.
1.3.6.1.4.1.3808.0.131
ePDUOutletLowLoad
NOTIFICATION-TYPE
WARNING: A Rack PDU has violated the outlet low load threshold. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.132
ePDUOutletLowLoadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The outlet low load condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.133
ePDUOutletNearOverload
NOTIFICATION-TYPE
WARNING: A Rack PDU is near an outlet overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.134
ePDUOutletNearOverloadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The outlet near overload condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.135
ePDUOutletOverload
NOTIFICATION-TYPE
SEVERE: A Rack PDU is in an overload condition. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.136
ePDUOutletOverloadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The outlet overload condition on a Rack PDU has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.137
envHighTemperatureViolation
NOTIFICATION-TYPE
WARNING: The environment high temperature threshold has been violated.
1.3.6.1.4.1.3808.0.200
envHighTemperatureBack
NOTIFICATION-TYPE
INFORMATION: The environment temperature returned from high value.
1.3.6.1.4.1.3808.0.201
envLowTemperatureViolation
NOTIFICATION-TYPE
WARNING: The environment low temperature threshold has been violated.
1.3.6.1.4.1.3808.0.202
envLowTempBack
NOTIFICATION-TYPE
INFORMATION: The environment temperature returned from low value.
1.3.6.1.4.1.3808.0.203
envHighHumidityViolation
NOTIFICATION-TYPE
WARNING: The environment high humidity threshold has been violated.
1.3.6.1.4.1.3808.0.204
envHighHumidityBack
NOTIFICATION-TYPE
INFORMATION: The environment humidity return from high value.
1.3.6.1.4.1.3808.0.205
envLowHumidityViolation
NOTIFICATION-TYPE
WARNING: The environment low humidity threshold has been violated.
1.3.6.1.4.1.3808.0.206
envLowHumdBack
NOTIFICATION-TYPE
INFORMATION: The environment humidity return from low value.
1.3.6.1.4.1.3808.0.207
envDryContactAbnormal
NOTIFICATION-TYPE
INFORMATION: The Contact is abnormal.
1.3.6.1.4.1.3808.0.208
envDryContactNormal
NOTIFICATION-TYPE
INFORMATION: The Contact has returned from abnormal.
1.3.6.1.4.1.3808.0.209
envConntected
NOTIFICATION-TYPE
INFORMATION: The Environment Sensor has been connected.
1.3.6.1.4.1.3808.0.210
envDisconntected
NOTIFICATION-TYPE
INFORMATION: The Environment Sensor has been disconnected.
1.3.6.1.4.1.3808.0.211
envRateOfTemperatureChangeAbnormal
NOTIFICATION-TYPE
INFORMATION: The rate of temperature change is abnormal.
1.3.6.1.4.1.3808.0.212
envRateOfHumdChangeAbnormal
NOTIFICATION-TYPE
INFORMATION: The rate of humidity change is abnormal.
1.3.6.1.4.1.3808.0.213
atsSwitchSource
NOTIFICATION-TYPE
INFORMATIONAL: ATS has switched source. The first argument is the device name. The second argument is the serial number. The third argument is the selected source.
1.3.6.1.4.1.3808.0.301
atsSourceFault
NOTIFICATION-TYPE
WARNING: Source fault occurs. The first argument is the device name. The second argument is the serial number. The third argument is the source name.
1.3.6.1.4.1.3808.0.302
atsSourceFaultCleared
NOTIFICATION-TYPE
INFORMATIONAL: Source fault has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name.
1.3.6.1.4.1.3808.0.303
atsRedundancyFail
NOTIFICATION-TYPE
WARNING: Redundancy fails. The first argument is the device name. The second argument is the serial number. The third argument is the source name.
1.3.6.1.4.1.3808.0.304
atsRedundancyRestored
NOTIFICATION-TYPE
INFORMATIONAL: Redundancy has been restored. The first argument is the device name. The second argument is the serial number. The third argument is the source name.
1.3.6.1.4.1.3808.0.305
atsInputHighVoltage
NOTIFICATION-TYPE
WARNING: The upper voltage limit has been crossed. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the phase voltage.
1.3.6.1.4.1.3808.0.306
atsInputHighVoltageCleared
NOTIFICATION-TYPE
INFORMATIONAL: The upper voltage condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the phase voltage.
1.3.6.1.4.1.3808.0.307
atsInputLowVoltage
NOTIFICATION-TYPE
WARNING: The lower voltage limit has been crossed. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the phase voltage.
1.3.6.1.4.1.3808.0.308
atsInputLowVoltageCleared
NOTIFICATION-TYPE
INFORMATIONAL: The lower voltage condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the phase voltage.
1.3.6.1.4.1.3808.0.309
atsInputHighFrequency
NOTIFICATION-TYPE
WARNING: The upper frequency limit has been crossed. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the input frequency.
1.3.6.1.4.1.3808.0.310
atsInputHighFrequencyCleared
NOTIFICATION-TYPE
INFORMATIONAL: The upper frequency condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the input frequency.
1.3.6.1.4.1.3808.0.311
atsInputLowFrequency
NOTIFICATION-TYPE
WARNING: The lower frequency limit has been crossed. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the input frequency.
1.3.6.1.4.1.3808.0.312
atsInputLowFrequencyCleared
NOTIFICATION-TYPE
INFORMATIONAL: The lower frequency condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the source name. The fourth argument is the input frequency.
1.3.6.1.4.1.3808.0.313
atsCommunicationLost
NOTIFICATION-TYPE
MAJOR: ATS communication lost. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.314
atsCommunicationEstablished
NOTIFICATION-TYPE
INFORMATIONAL: ATS communication has been established. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.315
atsLCDCommunicationLost
NOTIFICATION-TYPE
WARNING: LCD communication lost. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.316
atsLCDCommunicationLostCleared
NOTIFICATION-TYPE
INFORMATIONAL: LCD communication lost has been cleared. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.317
atsDB9CommunicationLost
NOTIFICATION-TYPE
WARNING: DB9 communication lost. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.318
atsDB9CommunicationLostCleared
NOTIFICATION-TYPE
INFORMATIONAL: DB9 communication lost has been cleared. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.319
atsPowerSupplyFault
NOTIFICATION-TYPE
CRITICAL: Power supply failure. The first argument is the device name. The second argument is the serial number. The third argument is the input source of the power supply.
1.3.6.1.4.1.3808.0.320
atsPowerSupplyFaultCleared
NOTIFICATION-TYPE
CRITICAL: Power supply failure. The first argument is the device name. The second argument is the serial number. The third argument is the input source of the power supply.
1.3.6.1.4.1.3808.0.321
atsDevHardwareFault
NOTIFICATION-TYPE
CRITICAL: Device hardware failure. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.322
atsDevHardwareFaultCleared
NOTIFICATION-TYPE
INFORMATIONAL: Device hardware failure has been cleared. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.323
atsSourceConfigChanged
NOTIFICATION-TYPE
INFORMATIONAL: A source configuration change has been made. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.324
atsDeviceConfigChanged
NOTIFICATION-TYPE
INFORMATIONAL: A device configuration change has been made. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.325
atsOutletConfigChanged
NOTIFICATION-TYPE
INFORMATIONAL: A outlet configuration change has been made. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.326
atsEventCountsCleared
NOTIFICATION-TYPE
INFORMATIONAL: Event counts has been cleared. The first argument is the device name. The second argument is the serial number.
1.3.6.1.4.1.3808.0.327
atsOverload
NOTIFICATION-TYPE
WARNING: The load has exceeded overload threshold. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
1.3.6.1.4.1.3808.0.328
atsOverloadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The overload condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
1.3.6.1.4.1.3808.0.329
atsNearOverload
NOTIFICATION-TYPE
WARNING: The load has exceeded near overload threshold. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
1.3.6.1.4.1.3808.0.330
atsNearOverloadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The near overload condition has beed cleared. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
1.3.6.1.4.1.3808.0.331
atsLowLoad
NOTIFICATION-TYPE
WARNING: The load has been lower than low load threshold. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
1.3.6.1.4.1.3808.0.332
atsLowLoadCleared
NOTIFICATION-TYPE
INFORMATIONAL: The low load condition has been cleared. The first argument is the device name. The second argument is the serial number. The third argument is the bank number. The third argument is the load.
1.3.6.1.4.1.3808.0.333
atsOutletOnCommand
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on ATS has been assigned to turn on. The first argument is the device name. The second argument is the serial number. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.334
atsOutletOffCommand
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on ATS has been assigned to turn off. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.335
atsOutletRebootCommand
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on ATS has been assigned to reboot. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.336
atsCancelPendingCommand
NOTIFICATION-TYPE
INFORMATIONAL: A cancel pending command has been made on ATS. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number (0 indicates all outlets). The fourth argument is the outlet name (or device name if all outlets).
1.3.6.1.4.1.3808.0.337
atsOutletOn
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on ATS has turned on. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.338
atsOutletOff
NOTIFICATION-TYPE
INFORMATIONAL: An outlet on ATS has turned off. The first argument is the serial number. The second argument is the device name. The third argument is the outlet index number. The fourth argument is the outlet name.
1.3.6.1.4.1.3808.0.339
pduDeviceEvent
NOTIFICATION-TYPE
INFORMATIONAL: A PDU device event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the device table index.
1.3.6.1.4.1.3808.0.400
pduDeviceAlarm
NOTIFICATION-TYPE
Alarm: A PDU device alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the device table index.
1.3.6.1.4.1.3808.0.401
pduDeviceAlarmClear
NOTIFICATION-TYPE
INFORMATIONAL: A PDU device alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the device table index.
1.3.6.1.4.1.3808.0.402
pduPhaseEvent
NOTIFICATION-TYPE
INFORMATIONAL: A PDU phase event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the phase table index. The foutrh argument is the phase number.
1.3.6.1.4.1.3808.0.403
pduPhaseAlarm
NOTIFICATION-TYPE
Alarm: A PDU phase alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the phase table index. The foutrh argument is the phase number.
1.3.6.1.4.1.3808.0.404
pduPhaseAlarmClear
NOTIFICATION-TYPE
INFORMATIONAL: A PDU phase alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the phase table index. The foutrh argument is the phase number.
1.3.6.1.4.1.3808.0.405
pduBankEvent
NOTIFICATION-TYPE
INFORMATIONAL: A PDU bank event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the bank table index. The foutrh argument is the bank number.
1.3.6.1.4.1.3808.0.406
pduBankAlarm
NOTIFICATION-TYPE
Alarm: A PDU bank alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the bank table index. The foutrh argument is the bank number.
1.3.6.1.4.1.3808.0.407
pduBankAlarmClear
NOTIFICATION-TYPE
INFORMATIONAL: A PDU bank alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the bank table index. The foutrh argument is the bank number.
1.3.6.1.4.1.3808.0.408
pduOutletSwitchedEvent
NOTIFICATION-TYPE
INFORMATIONAL: A PDU switched outlet event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
1.3.6.1.4.1.3808.0.409
pduOutletSwitchedAlarm
NOTIFICATION-TYPE
Alarm: A PDU switched outlet alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
1.3.6.1.4.1.3808.0.410
pduOutletSwitchedAlarmClear
NOTIFICATION-TYPE
INFORMATIONAL: A PDU switched outlet alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
1.3.6.1.4.1.3808.0.411
pduOutletMeteredEvent
NOTIFICATION-TYPE
INFORMATIONAL: A PDU metered outlet event has been happened. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
1.3.6.1.4.1.3808.0.412
pduOutletMeteredAlarm
NOTIFICATION-TYPE
Alarm: A PDU metered outlet alarm has been detected. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
1.3.6.1.4.1.3808.0.413
pduOutletMeteredAlarmClear
NOTIFICATION-TYPE
INFORMATIONAL: A PDU metered outlet alarm has been cleared. The first argument is the serial number. The second argument is the device name. The third argument is the outlet table index. The foutrh argument is the outlet number. The fifth argument is the outlet name.
1.3.6.1.4.1.3808.0.414
pduDaisyChainEvent
NOTIFICATION-TYPE
INFORMATIONAL: A PDU daisy-chain event has been happened. The first argument is the host serial number. The second argument is the host device name. The third argument is the event device table index. The foutrh argument is the event device serial number. The fifth argument is the event device name.
1.3.6.1.4.1.3808.0.415
pduDaisyChainAlarm
NOTIFICATION-TYPE
Alarm: A PDU daisy-chain alarm has been detected. The first argument is the host serial number. The second argument is the host device name. The third argument is the alarm device table index. The foutrh argument is the alarm device serial number. The fifth argument is the alarm device name.
1.3.6.1.4.1.3808.0.416
pduDaisyChainAlarmClear
NOTIFICATION-TYPE
INFORMATIONAL: A PDU daisy-chain alarm has been cleared. The first argument is the host serial number. The second argument is the host device name. The third argument is the alarm device table index. The foutrh argument is the alarm deice serial number. The fifth argument is the alarm device name.
1.3.6.1.4.1.3808.0.417
bmSystemAlarm
NOTIFICATION-TYPE
ALARM: System alarm occurance. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the alarm event specific identifier. The fifth argument is the trap information string.
1.3.6.1.4.1.3808.0.600
bmSystemWarning
NOTIFICATION-TYPE
WARNING: System warning occurance. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the alarm event specific identifier. The fifth argument is the trap information string.
1.3.6.1.4.1.3808.0.601
bmSystemInfo
NOTIFICATION-TYPE
INFO: System information. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the alarm event specific identifier. The fifth argument is the trap information string.
1.3.6.1.4.1.3808.0.602
bmProbesAlarm
NOTIFICATION-TYPE
ALARM: Probe alarm event. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the string index the probe located. The fifth argument is the battery index the probe located. The sixth argument is the alarm event specific identifier. The seventh argument is the trap information string.
1.3.6.1.4.1.3808.0.603
bmSProbesWarning
NOTIFICATION-TYPE
WARNING: Probe warning event. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the string index the probe located. The fifth argument is the battery index the probe located. The sixth argument is the alarm event specific identifier. The seventh argument is the trap information string.
1.3.6.1.4.1.3808.0.604
bmProbesInfo
NOTIFICATION-TYPE
INFO: Probe information. The first argument is the bm device serial number. The second argument is the bm system identification name. The third argument is the bm system location. The fourth argument is the string index the probe located. The fifth argument is the battery index the probe located. The sixth argument is the alarm event specific identifier. The seventh argument is the trap information string.
1.3.6.1.4.1.3808.0.605