MIBs Depot

CISCOSB-TIMESYNCHRONIZATION-MIB

Registered at
1.3.6.1.4.1.9.6.1.101.92
Last updated
2004-08-03 00:24
Organization
Cisco Systems, Inc.
Revisions
2009-06-18 00:24, 2007-09-06 00:24, 2003-11-23 00:24
Namespace
cisco
Source file
CISCOSB-TIMESYNCHRONIZATION-MIB
Digest
sha256:356ecfdd0230dc6debecadf99893ddbbebfc5e9e14b95915b05cbb262c2ce4bf

Description

The MIB module describes the private MIB for SNTP & TIME definitions.

Contact

Postal: 170 West Tasman Drive San Jose , CA 95134-1706 USA Website: Cisco Small Business Support Community <http://www.cisco.com/go/smallbizsupport>

Imports

FromSymbols
CISCOSB-MIBswitch001
IF-MIBInterfaceIndex
INET-ADDRESS-MIBInetAddress, InetAddressType
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIInteger32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDisplayString, RowStatus, TEXTUAL-CONVENTION, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

CISCOSB-MIB
CISCOSB-TIMESYNCHRONIZATION-MIB
IANAifType-MIB
IF-MIB
INET-ADDRESS-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC

Textual conventions

NameOIDSyntaxAccessStatus
NTPSignedTimeValue
TEXTUAL-CONVENTION
The time in seconds that could represent signed quantities like time delay with respect to some source. This textual-convention is specific to CISCOSB implementation of NTP where 32-bit integers are used for such quantities. The signed integer part is in the first 16 bits and the fraction part is in the last 16 bits.
current
NTPStratum
TEXTUAL-CONVENTION
Indicates the stratum of the clock. The stratum defines the accuracy of a time server. Higher the stratum, lower the accuracy. 0, unspecified 1, primary reference (e.g., calibrated atomic clock, radio clock) 2-255, secondary reference (via NTP)
current
NTPTimeStamp
TEXTUAL-CONVENTION
NTP timestamps are represented as a 64-bit unsigned fixed-point number, in seconds relative to 00:00 on 1 January 1900. The integer part is in the first 32 bits and the fraction part is in the last 32 bits.
current
RlDaylightSavingTimeMode
TEXTUAL-CONVENTION
Daylight Saving Time - Recurring/Date/None.
current
RlSntpNtpSyncEntryType
TEXTUAL-CONVENTION
Entry in rlSntpNtpConfigSrvTable.
current
RlSntpNtpSyncType
TEXTUAL-CONVENTION
Method to be used for time synchronization in the device.
current
RlTimeSyncMethod
TEXTUAL-CONVENTION
Method to be used for time synchronization in the device.
current

Objects

NameOIDSyntaxAccessStatus
rlTimeSyncMethodMode
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.92.1
rlTimeSyncMibVersion
OBJECT-TYPE
TimeSync Mib Version.
1.3.6.1.4.1.9.6.1.101.92.1.1INTEGERread-onlycurrent
rndTimeSyncManagedTime
OBJECT-TYPE
The time will be sent in the format hhmmss
1.3.6.1.4.1.9.6.1.101.92.1.2DisplayString (SIZE(6))read-writecurrent
rndTimeSyncManagedDate
OBJECT-TYPE
The date will be sent in the format ddmmyy
1.3.6.1.4.1.9.6.1.101.92.1.3DisplayString (SIZE(6))read-writecurrent
rndTimeSyncManagedDateTime
OBJECT-TYPE
The date and time will be sent in the format ddmmyyhhmmss
1.3.6.1.4.1.9.6.1.101.92.1.4DisplayString (SIZE(12))read-writecurrent
rlTimeSyncMethod
OBJECT-TYPE
Method to be used for time synchronization in the device.
1.3.6.1.4.1.9.6.1.101.92.1.5RlTimeSyncMethodread-writecurrent
rlTimeZone
OBJECT-TYPE
Offset from Greenwich time (format [+/-]hh:mm).
1.3.6.1.4.1.9.6.1.101.92.1.6DisplayString (SIZE(1..6))read-writecurrent
rlTimeZoneCode
OBJECT-TYPE
Code definition for current TimeZone.
1.3.6.1.4.1.9.6.1.101.92.1.7DisplayString (SIZE(0..16))read-writecurrent
rlDaylightSavingTimeMode
OBJECT-TYPE
Daylight Saving Time - Recurring/Date/None.
1.3.6.1.4.1.9.6.1.101.92.1.8RlDaylightSavingTimeModeread-writecurrent
rlDaylightSavingTimeStart
OBJECT-TYPE
Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1).
1.3.6.1.4.1.9.6.1.101.92.1.9OCTET STRING (SIZE(14))read-writecurrent
rlDaylightSavingTimeEnd
OBJECT-TYPE
Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1).
1.3.6.1.4.1.9.6.1.101.92.1.10OCTET STRING (SIZE(14))read-writecurrent
rlDaylightSavingTimeOffset
OBJECT-TYPE
Daylight Saving Time - The number of minutes to add to the clock during summer time.
1.3.6.1.4.1.9.6.1.101.92.1.11Integer32read-writecurrent
rlDaylightSavingTimeCode
OBJECT-TYPE
Code definition for current Daylight Saving Time.
1.3.6.1.4.1.9.6.1.101.92.1.12DisplayString (SIZE(0..16))read-writecurrent
rlTZDSTOffset
OBJECT-TYPE
Local Time Zone and Daylight Saving Time offset in seconds.
1.3.6.1.4.1.9.6.1.101.92.1.13INTEGERread-onlycurrent
rlTimeZoneName
OBJECT-TYPE
Human readable string describing Local Time Zone and Daylight Saving Time.
1.3.6.1.4.1.9.6.1.101.92.1.14DisplayString (SIZE(0..16))read-writecurrent
rlTimeZoneTable
OBJECT-TYPE
TimeZone information.
1.3.6.1.4.1.9.6.1.101.92.1.15not-accessiblecurrent
rlTimeZoneEntry
OBJECT-TYPE
The row definition for this table.
1.3.6.1.4.1.9.6.1.101.92.1.15.1not-accessiblecurrent
rlTimeZoneIndex
OBJECT-TYPE
Entry index. A row with index 2 will be existing in case the DHCP timezone is supported, and will contain Timezone and Summertime dynamic values. Using index 2 in SET operations is allowed only for SNMP inner clients (SNMPServ users), on condition that DHCP timezone option is supported.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.1INTEGER (1..2)not-accessiblecurrent
rlTimeZoneTimeSyncMethod
OBJECT-TYPE
Method to be used for time synchronization in the device.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.2RlTimeSyncMethodread-writecurrent
rlTimeZoneTimeZoneOffset
OBJECT-TYPE
Offset from Greenwich time (format [+/-]hh:mm).
1.3.6.1.4.1.9.6.1.101.92.1.15.1.3DisplayString (SIZE(1..6))read-writecurrent
rlTimeZoneTimeZoneCode
OBJECT-TYPE
Code definition for current TimeZone.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.4DisplayString (SIZE(0..16))read-writecurrent
rlTimeZoneDaylightSavingTimeMode
OBJECT-TYPE
Daylight Saving Time - Recurring/Date/None.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.5RlDaylightSavingTimeModeread-writecurrent
rlTimeZoneDaylightSavingTimeStart
OBJECT-TYPE
Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1).
1.3.6.1.4.1.9.6.1.101.92.1.15.1.6OCTET STRING (SIZE(14))read-writecurrent
rlTimeZoneDaylightSavingTimeEnd
OBJECT-TYPE
Daylight Saving Time start date. In recurring mode (format 1): week wday month hh:mm In recurring mode (format 2): RJul n hh:mm In date mode: month day year hh:mm week: 0-6 (0=First, 6=Last) wday: 1-7 (Sunday-Saturday) month: 1-12 (January-December) day: 1-31 year: 0-99 (2000-2099) hh: 0-23 (hours) mm: 0-59 (minutes) n: 0-365 (zero-based Julian day of the year. Leap days shall be counted, and it is possible to refer to February 29). Format 2 for recurring mode is used only in the dynamic entry and should not be used in the static entry (with index 1).
1.3.6.1.4.1.9.6.1.101.92.1.15.1.7OCTET STRING (SIZE(14))read-writecurrent
rlTimeZoneDaylightSavingTimeOffset
OBJECT-TYPE
Daylight Saving Time - The number of minutes to add to the clock during summer time.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.8Integer32read-writecurrent
rlTimeZoneDaylightSavingTimeCode
OBJECT-TYPE
Code definition for current Daylight Saving Time.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.9DisplayString (SIZE(0..16))read-writecurrent
rlTimeZoneTZDSTOffset
OBJECT-TYPE
Local Time Zone and Daylight Saving Time offset in seconds.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.10INTEGERread-onlycurrent
rlTimeZoneTimeZoneName
OBJECT-TYPE
Human readable string describing Local Time Zone and Daylight Saving Time.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.11DisplayString (SIZE(0..16))read-writecurrent
rlTimeZoneDataType
OBJECT-TYPE
The type of data in this entry: static or dynamic.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.12INTEGER {static(1), dynamic(2)}read-onlycurrent
rlTimeZoneDataSourceIfIndex
OBJECT-TYPE
IfIndex of the interface through which the dynamic data of this row has been learned. The value of this field will be 0 if rlTimeZoneTimeDataType is static (since it is relevant only for dynamic entry), and this is the only value allowed for SET in this case.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.13INTEGERread-writecurrent
rlTimeZoneDataDynamicConfSource
OBJECT-TYPE
The source of dynamic data in this entry, for example: dhcpv4. Values other than 'none' are relevant only for dynamic entry.
1.3.6.1.4.1.9.6.1.101.92.1.15.1.14INTEGER {none(1), dhcpv4(2), dhcpv6(3)}read-writecurrent
rlClockStatus
OBJECT-TYPE
Current status of the clock. The value 'invalid' means time is meaninglesss, since it has not been manually configured, or achieved as a result of SNTP synchronization or set by RTC.
1.3.6.1.4.1.9.6.1.101.92.1.16INTEGER {invalid(1), manuallySet(2), synchronizedBySntp(3), setByRtc(4)}read-onlycurrent
rlDhcpTimezoneOptionEnabled
OBJECT-TYPE
Specifies whether the DHCP Timezone option (DHCPv4 option 100) is supported in the system. Setting this value to FALSE, will clear Timezone and Summertime dynamic configuration, so that: 1) rlTimeZoneTimeZoneCode and rlTimeZoneDaylightSavingTimeCode length will be 0 for rlTimeZoneEntry whose index = 2 (dynamic entry). 2) the operative values of Timezone and Summertime will be those statically configured. Thus, GET operations on the following MIB scalars will result is static values: rlTimeZone, rlTimeZoneCode, rlDaylightSavingTimeMode, rlDaylightSavingTimeStart, rlDaylightSavingTimeEnd, rlDaylightSavingTimeOffset, rlDaylightSavingTimeCode, rlTZDSTOffset.
1.3.6.1.4.1.9.6.1.101.92.1.17TruthValueread-writecurrent
rlAutomaticClockSetFromPCEnabled
OBJECT-TYPE
Specifies whether automatic set of time and date is permitted from connected host PC. The feature is meant to be used in order to initialize the clock after reboot (if SNTP is not in use), since the device does not have a realtime clock.
1.3.6.1.4.1.9.6.1.101.92.1.18TruthValueread-writecurrent
rlTimeAndDateHaveBeenSet
OBJECT-TYPE
Indicates whether the time and date have been set in the device, manually or through SNTP synchronization. If only time has been set, the value of this MIB will be FALSE. If only date has been set, the value of this MIB will be FALSE.
1.3.6.1.4.1.9.6.1.101.92.1.19TruthValueread-onlycurrent
rlSntpNtpClient
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.92.2
rlSntpNtpConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.92.2.1
rlSntpNtpMibVersion
OBJECT-TYPE
SntpNtp Mib Version.
1.3.6.1.4.1.9.6.1.101.92.2.1.1INTEGERread-onlycurrent
rlSntpNtpConfigMode
OBJECT-TYPE
Current configuration operational mode of SNTP/NTP client.
1.3.6.1.4.1.9.6.1.101.92.2.1.2INTEGER {none(1), unicast(2), anycast(3), multicast(4), unicastAnycast(5), unicastMulticast(6), anycastMulticast(7), unicastAnycastMulticast(8)}read-onlycurrent
rlSntpNtpConfigSysStratum
OBJECT-TYPE
The stratum of the local clock. If the value is set to 1, i.e., this is a primary reference, then the Primary-Clock procedure described in Section 3.4.6, in RFC-1305 is invoked.
1.3.6.1.4.1.9.6.1.101.92.2.1.3NTPStratumread-onlycurrent
rlSntpNtpConfigPollInterval
OBJECT-TYPE
Period of time (in seconds) between succesive attempts to perform an update via SNTP.
1.3.6.1.4.1.9.6.1.101.92.2.1.4INTEGERread-writecurrent
rlSntpNtpConfigPrimaryPollSrvAddr
OBJECT-TYPE
Ip Address of a trusted SNTP server for polling.
1.3.6.1.4.1.9.6.1.101.92.2.1.5IpAddressread-onlycurrent
rlSntpNtpConfigPrimaryPollSrvMrid
OBJECT-TYPE
The mrid of the primary server.
1.3.6.1.4.1.9.6.1.101.92.2.1.6INTEGERread-onlycurrent
rlSntpNtpConfigPrimaryPollSrvIfIndex
OBJECT-TYPE
The interface addressed of the primary server.
1.3.6.1.4.1.9.6.1.101.92.2.1.7INTEGERread-onlycurrent
rlSntpNtpConfigPrimaryPollSrvStratum
OBJECT-TYPE
The stratum of the primary polling server.
1.3.6.1.4.1.9.6.1.101.92.2.1.8NTPStratumread-onlycurrent
rlSntpNtpConfigSyncSrvAddr
OBJECT-TYPE
Ip Address of the synced server.
1.3.6.1.4.1.9.6.1.101.92.2.1.9IpAddressread-onlycurrent
rlSntpNtpConfigSyncSrvMrid
OBJECT-TYPE
The mrid of the synced server.
1.3.6.1.4.1.9.6.1.101.92.2.1.10INTEGERread-onlycurrent
rlSntpNtpConfigSyncSrvIfIndex
OBJECT-TYPE
The interface addressed of the synced server.
1.3.6.1.4.1.9.6.1.101.92.2.1.11INTEGERread-onlycurrent
rlSntpNtpConfigSyncSrvType
OBJECT-TYPE
Synced server type.
1.3.6.1.4.1.9.6.1.101.92.2.1.12RlSntpNtpSyncTyperead-onlycurrent
rlSntpNtpConfigSyncSrvStratum
OBJECT-TYPE
The stratum of the synced server.
1.3.6.1.4.1.9.6.1.101.92.2.1.13NTPStratumread-onlycurrent
rlSntpNtpConfigRetryTimeout
OBJECT-TYPE
SNTP/NTP requests Retry Interval.
1.3.6.1.4.1.9.6.1.101.92.2.1.14Integer32read-onlycurrent
rlSntpNtpConfigRetryCnt
OBJECT-TYPE
SNTP/NTP requests Retry Count.
1.3.6.1.4.1.9.6.1.101.92.2.1.15Integer32read-onlycurrent
rlSntpNtpConfigSrvTable
OBJECT-TYPE
A table containing information about config servers.
1.3.6.1.4.1.9.6.1.101.92.2.1.16not-accessiblecurrent
rlSntpNtpConfigSrvEntry
OBJECT-TYPE
Entry in rlSntpNtpConfigSrvTable.
1.3.6.1.4.1.9.6.1.101.92.2.1.16.1not-accessiblecurrent
rlSntpNtpConfigSrvEntryType
OBJECT-TYPE
Server type: Synchronize Server or Primary Poll Server.
1.3.6.1.4.1.9.6.1.101.92.2.1.16.1.1RlSntpNtpSyncEntryTypenot-accessiblecurrent
rlSntpNtpConfigSrvInetAddressType
OBJECT-TYPE
Server inet address type.
1.3.6.1.4.1.9.6.1.101.92.2.1.16.1.2InetAddressTyperead-onlycurrent
rlSntpNtpConfigSrvInetAddress
OBJECT-TYPE
Server inet address.
1.3.6.1.4.1.9.6.1.101.92.2.1.16.1.3InetAddressread-onlycurrent
rlSntpNtpConfigSrvMrid
OBJECT-TYPE
The mrid of the server.
1.3.6.1.4.1.9.6.1.101.92.2.1.16.1.4INTEGERread-onlycurrent
rlSntpNtpConfigSrvIfIndex
OBJECT-TYPE
The interface addressed of the server.
1.3.6.1.4.1.9.6.1.101.92.2.1.16.1.5INTEGERread-onlycurrent
rlSntpNtpConfigSrvSyncType
OBJECT-TYPE
The type of synchronization.
1.3.6.1.4.1.9.6.1.101.92.2.1.16.1.6RlSntpNtpSyncTyperead-onlycurrent
rlSntpNtpConfigSrvStratum
OBJECT-TYPE
The stratum of the synced server.
1.3.6.1.4.1.9.6.1.101.92.2.1.16.1.7NTPStratumread-onlycurrent
rlSntpConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.92.2.2
rlSntpClientMode
OBJECT-TYPE
Current operational mode of SNTP client.
1.3.6.1.4.1.9.6.1.101.92.2.2.1INTEGER {none(1), active(2), passive(3)}read-onlycurrent
rlSntpUnicastAdminState
OBJECT-TYPE
SNTP Unicast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled.
1.3.6.1.4.1.9.6.1.101.92.2.2.2INTEGER {enabled(1), disabled(2)}read-writecurrent
rlSntpBroadcastAdminState
OBJECT-TYPE
SNTP Broadcast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled.
1.3.6.1.4.1.9.6.1.101.92.2.2.3INTEGER {enabled(1), disabled(2), ipv4OnlyEnabled(3), ipv6OnlyEnabled(4)}read-writecurrent
rlSntpAnycastAdminState
OBJECT-TYPE
SNTP Anycast Administrative state - Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled.
1.3.6.1.4.1.9.6.1.101.92.2.2.4INTEGER {enabled(1), disabled(2), ipv4OnlyEnabled(3), ipv6OnlyEnabled(4)}read-writecurrent
rlSntpUnicastPollState
OBJECT-TYPE
SNTP Unicast poll state - TRUE for polled.
1.3.6.1.4.1.9.6.1.101.92.2.2.5TruthValueread-writecurrent
rlSntpBroadcastPollState
OBJECT-TYPE
SNTP Broadcast poll state - TRUE for polled.
1.3.6.1.4.1.9.6.1.101.92.2.2.6TruthValueread-writecurrent
rlSntpAnycastPollState
OBJECT-TYPE
SNTP Anycast poll state - TRUE for polled.
1.3.6.1.4.1.9.6.1.101.92.2.2.7TruthValueread-writecurrent
rlSntpAuthenticationState
OBJECT-TYPE
SNTP authentication state- Enable/Disable SNTP.
1.3.6.1.4.1.9.6.1.101.92.2.2.8INTEGER {enabled(1), disabled(2)}read-writecurrent
rlTimeValidFlag
OBJECT-TYPE
Is time valid.
1.3.6.1.4.1.9.6.1.101.92.2.2.9TruthValueread-writecurrent
rlSntpConfigBroadcastTable
OBJECT-TYPE
A table containing broadcast mode information per interface.
1.3.6.1.4.1.9.6.1.101.92.2.2.10not-accessiblecurrent
rlSntpBroadcastEntry
OBJECT-TYPE
Private paramters for interface: sntp status, broadcast mode.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1not-accessiblecurrent
rlSntpBroadcastIfIndex
OBJECT-TYPE
The interface addressed by this entry.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.1INTEGERnot-accessiblecurrent
rlSntpBroadcastIfAdminState
OBJECT-TYPE
SNTP interface Adminstrative state- Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
rlSntpBroadcastMode
OBJECT-TYPE
SNTP/NTP Broadcast Mode. none - no broadcast SNTP packets are received or sent. Receive - host only receive SNTP packets that were sent to broadcast address (were not directed to the host). This is multicast mode in the RFC. Send - host only send SNTP packets and wait for replies directed to the host. This is anycast mode in the RFC. ReceiveSend - host receive broadcast messages (destination is broadcast address in the received messages) and send SNTP packets to wait for replies directed to the host (destination address of the reply is the host address). This mode combines anycast and multicast modes in the RFC.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.3INTEGER {none(1), receive(2), send(3), receiveSend(4)}read-writecurrent
rlSntpBroadcastPolled
OBJECT-TYPE
TRUE if participating in polling cycle, else FALSE.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.4TruthValueread-writecurrent
rlSntpBroadcastAddress
OBJECT-TYPE
Ip Address of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.5IpAddressread-onlycurrent
rlSntpBroadcastStratum
OBJECT-TYPE
The stratum of this server.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.6NTPStratumread-onlycurrent
rlSntpBroadcastLastResp
OBJECT-TYPE
SNTP Broadcast Last Response Time
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.7NTPTimeStampread-onlycurrent
rlSntpBroadcastStatus
OBJECT-TYPE
The Operational State of the remote IP Address of the SNTP Broadcast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.8INTEGER {unknown(1), inProcess(2), up(3), down(4)}read-onlycurrent
rlSntpBroadcastOffset
OBJECT-TYPE
The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.9NTPTimeStampread-onlycurrent
rlSntpBroadcastDelay
OBJECT-TYPE
The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.10NTPSignedTimeValueread-onlycurrent
rlSntpBroadcastRowStatus
OBJECT-TYPE
The Status of this SNTP broadcast interface information.
1.3.6.1.4.1.9.6.1.101.92.2.2.10.1.11RowStatusread-writecurrent
rlSntpConfigAnycastTable
OBJECT-TYPE
A table containing anycast information per interface.
1.3.6.1.4.1.9.6.1.101.92.2.2.11not-accessiblecurrent
rlSntpAnycastEntry
OBJECT-TYPE
Private paramters for interface: server info.
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1not-accessiblecurrent
rlSntpAnycastIfIndex
OBJECT-TYPE
The interface addressed by this entry.
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1.1INTEGERnot-accessiblecurrent
rlSntpAnycastAddress
OBJECT-TYPE
Ip Address of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1.2IpAddressread-onlycurrent
rlSntpAnycastStratum
OBJECT-TYPE
The stratum of this server.
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1.3NTPStratumread-onlycurrent
rlSntpAnycastLastResp
OBJECT-TYPE
SNTP Anycast Last Response Time
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1.4NTPTimeStampread-onlycurrent
rlSntpAnycastStatus
OBJECT-TYPE
The Operational State of the remote IP Address of the SNTP Anycast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets.
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1.5INTEGER {unknown(1), inProcess(2), up(3), down(4)}read-onlycurrent
rlSntpAnycastOffset
OBJECT-TYPE
The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1.6NTPTimeStampread-onlycurrent
rlSntpAnycastDelay
OBJECT-TYPE
The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1.7NTPSignedTimeValueread-onlycurrent
rlSntpAnycastRowStatus
OBJECT-TYPE
The Status of this SNTP anycast interface information.
1.3.6.1.4.1.9.6.1.101.92.2.2.11.1.8RowStatusread-writecurrent
rlSntpConfigServerTable
OBJECT-TYPE
A table containing trusted SNTP servers to be queried in unicast or broadcast mode.
1.3.6.1.4.1.9.6.1.101.92.2.2.12not-accessiblecurrent
rlSntpServerEntry
OBJECT-TYPE
A trusted server.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1not-accessiblecurrent
rlSntpServerAddress
OBJECT-TYPE
Ip Address of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.1IpAddressnot-accessiblecurrent
rlSntpServerPolled
OBJECT-TYPE
TRUE if participating in polling cycle, else FALSE.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.2TruthValueread-writecurrent
rlSntpServerStratum
OBJECT-TYPE
The stratum of this server.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.3NTPStratumread-onlycurrent
rlSntpServerLastResp
OBJECT-TYPE
SNTP Server Last Response Time
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.4NTPTimeStampread-onlycurrent
rlSntpServerStatus
OBJECT-TYPE
The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.5INTEGER {unknown(1), inProcess(2), up(3), down(4)}read-onlycurrent
rlSntpServersOffset
OBJECT-TYPE
The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.6NTPTimeStampread-onlycurrent
rlSntpServersDelay
OBJECT-TYPE
The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.7NTPSignedTimeValueread-onlycurrent
rlSntpServersKeyIdentifier
OBJECT-TYPE
Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.8Unsigned32read-writecurrent
rlSntpServerRowStatus
OBJECT-TYPE
The Status of this SNTP server information.
1.3.6.1.4.1.9.6.1.101.92.2.2.12.1.9RowStatusread-writecurrent
rlSntpConfigAuthenticationTable
OBJECT-TYPE
A table authentication keys.
1.3.6.1.4.1.9.6.1.101.92.2.2.13not-accessiblecurrent
rlSntpAuthenticationEntry
OBJECT-TYPE
Keys information for authenticationof NTP packets.
1.3.6.1.4.1.9.6.1.101.92.2.2.13.1not-accessiblecurrent
rlSntpAuthenticationKeyID
OBJECT-TYPE
The key identifier. Valid rabge for key identifier is 1-4294967295.
1.3.6.1.4.1.9.6.1.101.92.2.2.13.1.1Unsigned32 (1..4294967295)read-writecurrent
rlSntpAuthenticationKeyValue
OBJECT-TYPE
Key value.
1.3.6.1.4.1.9.6.1.101.92.2.2.13.1.2DisplayString (SIZE(1..8))read-writecurrent
rlSntpAuthenticationKeyState
OBJECT-TYPE
Authentication key state - Enable/Disable key.
1.3.6.1.4.1.9.6.1.101.92.2.2.13.1.3INTEGER {enabled(1), disabled(2)}read-writecurrent
rlSntpAuthenticationRowStatus
OBJECT-TYPE
The Status of this Authentication key information.
1.3.6.1.4.1.9.6.1.101.92.2.2.13.1.4RowStatusread-writecurrent
rlSntpPort
OBJECT-TYPE
User defined SNTP port.
1.3.6.1.4.1.9.6.1.101.92.2.2.14INTEGER (1..65535)read-writecurrent
rlSntpConfigBroadcastInetTable
OBJECT-TYPE
A table containing broadcast mode information per interface.
1.3.6.1.4.1.9.6.1.101.92.2.2.15not-accessiblecurrent
rlSntpBroadcastInetEntry
OBJECT-TYPE
Private paramters for interface: sntp status, broadcast mode.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1not-accessiblecurrent
rlSntpBroadcastInetIfIndex
OBJECT-TYPE
The interface addressed by this entry.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.1INTEGERnot-accessiblecurrent
rlSntpBroadcastInetIfAdminState
OBJECT-TYPE
SNTP interface Adminstrative state- Enable/Disable SNTP. In case of reinitializing polling or time synchronization this MIB is modified. The MIB can be enabled even thought it is already enabled.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.2INTEGER {enabled(1), disabled(2)}read-writecurrent
rlSntpBroadcastInetMode
OBJECT-TYPE
SNTP/NTP Broadcast Mode. none - no broadcast SNTP packets are received or sent. Receive - host only receive SNTP packets that were sent to broadcast address (were not directed to the host). This is multicast mode in the RFC. Send - host only send SNTP packets and wait for replies directed to the host. This is anycast mode in the RFC. ReceiveSend - host receive broadcast messages (destination is broadcast address in the received messages) and send SNTP packets to wait for replies directed to the host (destination address of the reply is the host address). This mode combines anycast and multicast modes in the RFC.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.3INTEGER {none(1), receive(2), send(3), receiveSend(4)}read-writecurrent
rlSntpBroadcastInetPolled
OBJECT-TYPE
TRUE if participating in polling cycle, else FALSE.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.4TruthValueread-writecurrent
rlSntpBroadcastInetAddressType
OBJECT-TYPE
Inet Address Type of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.5InetAddressTyperead-onlycurrent
rlSntpBroadcastInetAddress
OBJECT-TYPE
Inet Address of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.6InetAddressread-onlycurrent
rlSntpBroadcastInetStratum
OBJECT-TYPE
The stratum of this server.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.7NTPStratumread-onlycurrent
rlSntpBroadcastInetLastResp
OBJECT-TYPE
SNTP Broadcast Last Response Time
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.8NTPTimeStampread-onlycurrent
rlSntpBroadcastInetStatus
OBJECT-TYPE
The Operational State of the remote IP Address of the SNTP Broadcast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.9INTEGER {unknown(1), inProcess(2), up(3), down(4)}read-onlycurrent
rlSntpBroadcastInetOffset
OBJECT-TYPE
The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.10NTPTimeStampread-onlycurrent
rlSntpBroadcastInetDelay
OBJECT-TYPE
The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.11NTPSignedTimeValueread-onlycurrent
rlSntpBroadcastInetRowStatus
OBJECT-TYPE
The Status of this SNTP broadcast interface information.
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.12RowStatusread-writecurrent
rlSntpBroadcastInetLastReq
OBJECT-TYPE
SNTP Broadcast Last Request Time
1.3.6.1.4.1.9.6.1.101.92.2.2.15.1.13NTPTimeStampread-onlycurrent
rlSntpConfigAnycastInetTable
OBJECT-TYPE
A table containing anycast information per interface.
1.3.6.1.4.1.9.6.1.101.92.2.2.16not-accessiblecurrent
rlSntpAnycastInetEntry
OBJECT-TYPE
Private paramters for interface: server info.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1not-accessiblecurrent
rlSntpAnycastInetIfIndex
OBJECT-TYPE
The interface addressed by this entry.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.1INTEGERnot-accessiblecurrent
rlSntpAnycastInetAddressType
OBJECT-TYPE
Inet Address Type of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.2InetAddressTyperead-onlycurrent
rlSntpAnycastInetAddress
OBJECT-TYPE
Inet Address of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.3InetAddressread-onlycurrent
rlSntpAnycastInetStratum
OBJECT-TYPE
The stratum of this server.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.4NTPStratumread-onlycurrent
rlSntpAnycastInetLastResp
OBJECT-TYPE
SNTP Anycast Last Response Time
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.5NTPTimeStampread-onlycurrent
rlSntpAnycastInetStatus
OBJECT-TYPE
The Operational State of the remote IP Address of the SNTP Anycast. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.6INTEGER {unknown(1), inProcess(2), up(3), down(4)}read-onlycurrent
rlSntpAnycastInetOffset
OBJECT-TYPE
The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.7NTPTimeStampread-onlycurrent
rlSntpAnycastInetDelay
OBJECT-TYPE
The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.8NTPSignedTimeValueread-onlycurrent
rlSntpAnycastInetRowStatus
OBJECT-TYPE
The Status of this SNTP anycast interface information.
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.9RowStatusread-writecurrent
rlSntpAnycastInetLastReq
OBJECT-TYPE
SNTP Anycast Last Request Time
1.3.6.1.4.1.9.6.1.101.92.2.2.16.1.10NTPTimeStampread-onlycurrent
rlSntpConfigServerInetTable
OBJECT-TYPE
A table containing trusted SNTP servers to be queried in unicast or broadcast mode.
1.3.6.1.4.1.9.6.1.101.92.2.2.17not-accessiblecurrent
rlSntpServerInetEntry
OBJECT-TYPE
A trusted server.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1not-accessiblecurrent
rlSntpServerInetAddressType
OBJECT-TYPE
Inet Address Type of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.1InetAddressTypenot-accessiblecurrent
rlSntpServerInetAddress
OBJECT-TYPE
Inet Address of a trusted SNTP server.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.2InetAddressnot-accessiblecurrent
rlSntpServerInetPolled
OBJECT-TYPE
TRUE if participating in polling cycle, else FALSE.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.3TruthValueread-writecurrent
rlSntpServerInetStratum
OBJECT-TYPE
The stratum of this server.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.4NTPStratumread-onlycurrent
rlSntpServerInetLastResp
OBJECT-TYPE
SNTP Server Last Response Time
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.5NTPTimeStampread-onlycurrent
rlSntpServerInetStatus
OBJECT-TYPE
The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.6INTEGER {unknown(1), inProcess(2), up(3), down(4)}read-onlycurrent
rlSntpServerInetOffset
OBJECT-TYPE
The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.7NTPTimeStampread-onlycurrent
rlSntpServerInetDelay
OBJECT-TYPE
The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.8NTPSignedTimeValueread-onlycurrent
rlSntpServerInetKeyIdentifier
OBJECT-TYPE
Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.9Unsigned32read-writecurrent
rlSntpServerInetRowStatus
OBJECT-TYPE
The Status of this SNTP server information.
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.10RowStatusread-writecurrent
rlSntpServerInetLastReq
OBJECT-TYPE
SNTP Server Last Request Time
1.3.6.1.4.1.9.6.1.101.92.2.2.17.1.11NTPTimeStampread-onlycurrent
rlSntpAllServerInetTable
OBJECT-TYPE
A table containing all SNTP servers (for example: statically configured, dynamically configured) to be queried in unicast or broadcast mode.
1.3.6.1.4.1.9.6.1.101.92.2.2.18not-accessiblecurrent
rlSntpAllServerInetEntry
OBJECT-TYPE
A server entry.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1not-accessiblecurrent
rlSntpAllServerSource
OBJECT-TYPE
The SNTP server source: static means manually defined, dhcpv6 means learnt from DHCP. Only static entries are stored in CDB.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.1INTEGER {static(1), dhcpv6(2), dhcpv4(3)}not-accessiblecurrent
rlSntpAllServerIfIndex
OBJECT-TYPE
The ifIndex from which the SNTP server configuration was received (for dhcpv6 configurations). For static entries the value of this field will always be 1.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.2InterfaceIndexnot-accessiblecurrent
rlSntpAllServerPreference
OBJECT-TYPE
The preference of SNTP server (for dhcpv6 configurations). For static entries the value of this field will always be 0.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.3INTEGERnot-accessiblecurrent
rlSntpAllServerInetAddressType
OBJECT-TYPE
SNTP server inet address type.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.4InetAddressTypenot-accessiblecurrent
rlSntpAllServerInetAddress
OBJECT-TYPE
SNTP server inet address.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.5InetAddressnot-accessiblecurrent
rlSntpAllServerInetPolled
OBJECT-TYPE
TRUE if participating in polling cycle, else FALSE.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.6TruthValueread-onlycurrent
rlSntpAllServerInetStratum
OBJECT-TYPE
The stratum of this server.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.7NTPStratumread-onlycurrent
rlSntpAllServerInetLastResp
OBJECT-TYPE
SNTP Server Last Response Time
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.8NTPTimeStampread-onlycurrent
rlSntpAllServerInetStatus
OBJECT-TYPE
The Operational State of the remote IP Address of the SNTP Server. unknown - requests were not sent yet. inProcess - replies were not received yet. up - server sent SNTP packets. down - server stopped sending SNTP packets.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.9INTEGER {unknown(1), inProcess(2), up(3), down(4)}read-onlycurrent
rlSntpAllServerInetOffset
OBJECT-TYPE
The estimated offset of the server's clock relative to the local clock, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.10NTPTimeStampread-onlycurrent
rlSntpAllServerInetDelay
OBJECT-TYPE
The estimated round-trip delay of the server's clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the algorithm described in RFC 2030.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.11NTPSignedTimeValueread-onlycurrent
rlSntpAllServerInetKeyIdentifier
OBJECT-TYPE
Authentication key identifier. The valid range is 1-4294967295. Value zero, means no authentication is being done.
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.12Unsigned32read-writecurrent
rlSntpAllServerInetLastReq
OBJECT-TYPE
SNTP Server Last Request Time
1.3.6.1.4.1.9.6.1.101.92.2.2.18.1.13NTPTimeStampread-onlycurrent
rlSntpRestoreDefaultServers
OBJECT-TYPE
Setting this scalar to true restores sntp default unicast servers. Meaning: all manually configured servers are deleted, and the default SNTP servers are recreated with their default values. This is an 'action' scalar.
1.3.6.1.4.1.9.6.1.101.92.2.2.19TruthValueread-writecurrent
rlSntpTimeSinceLastSync
OBJECT-TYPE
SNTP time in seconds since last sync.
1.3.6.1.4.1.9.6.1.101.92.2.2.20Unsigned32read-onlycurrent
rlNtpConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.6.1.101.92.2.3