CISCO-SDSL-LINE-MIB
- Registered at
- 1.3.6.1.4.1.9.9.155
- Last updated
- 2001-08-20 10:00
- Organization
- Cisco Systems, Inc.
- Revisions
- 2001-08-20 10:00, 2001-04-09 10:13, 2001-01-30 16:00
- Namespace
- cisco
- Source file
CISCO-SDSL-LINE-MIB- Digest
sha256:e158ad25c90441704986e69f5e14c4613e0fb17891616ea7ce54816bdaacf01e
Description
This MIB module describes all variations of the symmetric DSL line interfaces. The structure of this module resembles and maintains consistency with the ADSL-LINE-MIB, ADSL-DMT-LINE-MIB, CISCO-ADSL-DMT-LINE-MIB, and CISCO-ADSL-CAP-LINE-MIB. Observe that the tables in this module do not necessarily extend the tables defined by the these mibs. Currently, only those tables that contain configuration information extend the profile tables defined by the above modules. This allows the management client to define DSL configuration profiles that apply across all DSL modems, independent of the technology being utilized by the modem. *** DEFINITIONS *** ATTENUATION Attenuation is a decrease in the strength of a signal over the length of a cable. CODING VIOLATION A coding violation occurs when the incoming signal exhibits a CRC anomaly. DOWNSTREAM The flow of data in the direction from the ATU-C to ATU-R. ERRORED SECOND A second with one or more coding violations or one or more incoming defects (e.g., LOS or LOSQ). LINE RATE The total data rate supported by a line. Observe that the payload rate is equal the line rate for the earliest implementations of SDSL. However, the payload rate maybe less than the line rate for future implementations. LOSS OF SYNC DEFECT A Loss of Sync Defect is defined as 3 consecutive received frames which contain one or more errors in the framing bits. A Loss of Sync Defect shall be cleared when at least 2 consecutive received frames contain no errors in the framing bits. LOSS OF SYNC FAILURE A LOSW Failure is defined as at least 2 consecutive seconds of LOSW Defect. The LOSW Failure should be cleared when the LOSW defect is absent for 20 seconds or less. (i.e. clear within 20 seconds ). MARGIN (also referred to as 'SNR margin') The difference between the SNR of the received signal and the SNR required to provide a BER of 10E-7. SEVERELY ERRORED SECOND A one second interval during which or more LOSW or CV defects are declared. UNAVAILABLE SECOND A Unavailable Second is defined as a one second interval during which LOSW Failure ( at least 2 seconds of LOSW Defect ). UPSTREAM The flow of data in the direction from the ATU-R to ATU-C. *** ABBREVIATIONS, ACRONYMS, AND SYMBOLS *** ADSL - Asymmetric Digital Subscriber Line. ATM - Asynchronous Transfer Mode. BER - Bit Error Ratio. CV - Coding Violation. DSL - Digital Subscriber Line. ES - Errored Second. LOS - Loss Of Sync. LOSQ - Loss Of Signal Quality. LOSW - Loss of Sync Word Failure PSD - Power Spectral Density. SES - Severely Errored Second. SNR - Signal-to-Noise Ratio. STM - Synchronous Transfer Mode. STU-C - SDSL Transceiver Unit, Central Office end. STU-R - ADSL Transceiver Unit, Remote terminal end. UAS - UnAvailable Second.
Contact
Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 Tel: +1 800 553-NETS E-mail: cs-dslam@cisco.com
Imports
| From | Symbols |
|---|---|
| ADSL-LINE-MIB | AdslLineProfileName, adslLineAlarmConfProfileName, adslLineConfProfileName |
| CISCO-SMI | ciscoMgmt |
| IF-MIB | ifIndex |
| PerfHist-TC-MIB | PerfCurrentCount, PerfIntervalCount |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Gauge32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso |
| SNMPv2-TC | DisplayString, TEXTUAL-CONVENTION, TruthValue, VariablePointer |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
ADSL-LINE-MIB ADSL-TC-MIB CISCO-SDSL-LINE-MIB CISCO-SMI IANAifType-MIB IF-MIB PerfHist-TC-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| SdslPerfCurrDayCount TEXTUAL-CONVENTION A counter associated with interval performance measurements in a current 1-day (24 hour) measurement interval. The value of this counter starts at zero at the beginning of an interval and increases when associated events occur, until the end of the 1-day interval. At that time, the agent stores the value of the counter in the previous 1-day history interval, if available, and resets the value of the counter to zero. In the case where the agent has no valid data available for this interval, the corresponding object instance is not available. In this case, the agent will respond with the appropriate error indicating that the instance does not exist; that is, 'noSuchName' in response to a SNMPv1 get request, and 'noSuchInstance' in response to a SNMPv2 get request. | current | |||
| SdslPerfPrevDayCount TEXTUAL-CONVENTION A counter associated with interval performance measurements during the most previous 1-day (24 hour) measurement interval. The value of this counter is equal to the current day counter at the end of its most recent interval. In the case where the agent has no valid data available for this interval, the corresponding object instance is not available. In this case, the agent will respond with the appropriate error indicating that the instance does not exist; that is, 'noSuchName' in response to a SNMPv1 get request, and 'noSuchInstance' in response to a SNMPv2 get request. | current | |||
| SdslPerfTimeElapsed TEXTUAL-CONVENTION The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. | current | |||
| SdslStuxDefect TEXTUAL-CONVENTION This object specifies any possible defects currently being exhibited by the STU-x. The value of this object is a bitmap of possible defects. The following list summarizes the meaning of each bit in the bitmap 0 lossOfSignal The STU-x is not receiving signal. 1 lossOfSignalQuality The upstream SNR margin has fallen below the SNR margin required to maintain a minimum BER of 10^-7. 2 noPeerStuPresent The STU-x can not initialize due to the absence of a peer STU-x. 3 lossOfSyncFailure The STU-x has suffered from at least 2 consecutive seconds of LOSW defect. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ciscoSdslLineMIBObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.155.1 | |||
| cSdslLineTable OBJECT-TYPE This table contains the enterprise-specific common attributes describing both ends of SDSL lines supported by the system. | 1.3.6.1.4.1.9.9.155.1.1 | not-accessible | current | |
| cSdslLineEntry OBJECT-TYPE A set of enterprise-specific common attributes describing both ends of an SDSL line supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | 1.3.6.1.4.1.9.9.155.1.1.1 | not-accessible | current | |
| cSdslLineCoding OBJECT-TYPE Specifies encoding of signal used by this line. Other types may be added in the future. | 1.3.6.1.4.1.9.9.155.1.1.1.1 | INTEGER {other(1), base2b1q(2), tcPam(3), optis(4), cap(5)} | read-only | current |
| cSdslLineFraming OBJECT-TYPE This object specifies the current Transmission Convergence framing structure being used by the interface. | 1.3.6.1.4.1.9.9.155.1.1.1.2 | INTEGER {none(1), other(2), hdsl(3), gShdsl(4), hdsl2(5), ds1(6)} | read-only | current |
| cSdslLineSpecific OBJECT-TYPE This object specifies an object identifier of an instance of an object in the MIB. The implementation determines the application of this object. For example, an implementation may use this object to provide a reference to the port-class physical entity (see the ENTITY-MIB for further details) corresponding to the SDSL line. | 1.3.6.1.4.1.9.9.155.1.1.1.3 | VariablePointer | read-only | current |
| cSdslLineConfProfile OBJECT-TYPE This object specifies the row in the adslLineConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this SDSL line interface. In the case the implementation utilizes 'dynamic mode' (see the ADSL-LINE-MIB for further details), then the value of this object defaults to the name of a configuration profile designated by the implementation as the default configuration profile. In the case the implementation utilizes 'static mode', then the the value of this object is read-only. | 1.3.6.1.4.1.9.9.155.1.1.1.4 | AdslLineProfileName | read-write | current |
| cSdslLineAlarmConfProfile OBJECT-TYPE This object specifies the row in the adslLineAlarmConfProfileTable (see the ADSL-LINE-MIB for further details), which applies for this SDSL line interface. In the case the implementation utilizes 'dynamic mode' (see the ADSL-LINE-MIB for further details), then the value of this object defaults to the name of an alarm configuration profile designated by the implementation as the default alarm configuration profile. In the case the implementation utilizes 'static mode', then the the value of this object is read-only. | 1.3.6.1.4.1.9.9.155.1.1.1.5 | AdslLineProfileName | read-write | current |
| cSdslStucPhysTable OBJECT-TYPE This table contains enterprise-specific physical layer parameters for STU-C class devices supported by the system. | 1.3.6.1.4.1.9.9.155.1.2 | not-accessible | current | |
| cSdslStucPhysEntry OBJECT-TYPE A set of enterprise-specific physical-layer parameters for an STU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | 1.3.6.1.4.1.9.9.155.1.2.1 | not-accessible | current | |
| cSdslStucInvSerialNumber OBJECT-TYPE This object specifies the vendor specific string that identifies the vendor STU-C. | 1.3.6.1.4.1.9.9.155.1.2.1.1 | SnmpAdminString (SIZE(0..32)) | read-only | current |
| cSdslStucInvVendorId OBJECT-TYPE This object specifies the vendor identifier assigned according to T1.220 | 1.3.6.1.4.1.9.9.155.1.2.1.2 | SnmpAdminString (SIZE(0..16)) | read-only | current |
| cSdslStucInvVersionNumber OBJECT-TYPE This object specifies the vendor specific version number of the STU-C. | 1.3.6.1.4.1.9.9.155.1.2.1.3 | SnmpAdminString (SIZE(0..16)) | read-only | current |
| cSdslStucState OBJECT-TYPE This object specifies the state of the STU-C transceiver. | 1.3.6.1.4.1.9.9.155.1.2.1.4 | INTEGER {other(1), idle(2), training(3), steadyState(4), testing(5), downloading(6), downloadFailed(7)} | read-only | current |
| cSdslStucDefect OBJECT-TYPE This object specifies any possible defects currently being exhibited by the STU-C. This object has the intention of supplementing ifOperStatus. | 1.3.6.1.4.1.9.9.155.1.2.1.5 | SdslStuxDefect | read-only | current |
| cSdslStucCurrRate OBJECT-TYPE This object specifies the rate the STU-C transceiver was able to obtain following training. | 1.3.6.1.4.1.9.9.155.1.2.1.6 | Integer32 (0..2320000) | read-only | current |
| cSdslStucCurrSnrMgn OBJECT-TYPE This object specifies the SNR margin as seen by this STU-C with respect to its received signal. | 1.3.6.1.4.1.9.9.155.1.2.1.7 | Gauge32 | read-only | current |
| cSdslStucCurrGain OBJECT-TYPE This object specifies gain applied to this STU-C's receiver. This object is deprecated by cSdslStucCurrGainRev which has no specified range. | 1.3.6.1.4.1.9.9.155.1.2.1.8 | Integer32 (-200..200) | read-only | deprecated |
| cSdslStucCurrOutputPwr OBJECT-TYPE This object specifies the measured total output power transmitted by this STU-C. This is the measurement that was reported during the last activation sequence. | 1.3.6.1.4.1.9.9.155.1.2.1.9 | Gauge32 | read-only | current |
| cSdslStucCurrAtn OBJECT-TYPE Measured difference in the total power transmitted by the peer STU-R and the total power received by this STU-C. | 1.3.6.1.4.1.9.9.155.1.2.1.10 | Gauge32 | read-only | current |
| cSdslStucCurrGainRev OBJECT-TYPE This object specifies gain applied to this STU-C's receiver. This object deprecates cSdslStucCurrGainRev and has no specified range. | 1.3.6.1.4.1.9.9.155.1.2.1.11 | Integer32 | read-only | current |
| cSdslSturPhysTable OBJECT-TYPE This table contains enterprise-specific physical layer parameters for STU-R class devices supported by the system. -- Note to implementor: -- If the implementation does not support remote management -- of STU-R class devices, then the agent must respond with -- the appropriate error indicating that the instance does not -- exist; that is, 'noSuchName' in response to a SNMPv1 get -- request, 'noSuchInstance' in response to a SNMPv2 get -- request or a null string for string types. | 1.3.6.1.4.1.9.9.155.1.3 | not-accessible | current | |
| cSdslSturPhysEntry OBJECT-TYPE A set of enterprise-specific physical-layer parameters for an STU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | 1.3.6.1.4.1.9.9.155.1.3.1 | not-accessible | current | |
| cSdslSturInvSerialNumber OBJECT-TYPE This object specifies the vendor specific string that identifies the vendor STU-R. | 1.3.6.1.4.1.9.9.155.1.3.1.1 | SnmpAdminString (SIZE(0..32)) | read-only | current |
| cSdslSturInvVendorId OBJECT-TYPE This object specifies the vendor identifier assigned according to T1.220 | 1.3.6.1.4.1.9.9.155.1.3.1.2 | SnmpAdminString (SIZE(0..16)) | read-only | current |
| cSdslSturInvVersionNumber OBJECT-TYPE This object specifies the vendor specific version number of the STU-R. | 1.3.6.1.4.1.9.9.155.1.3.1.3 | SnmpAdminString (SIZE(0..16)) | read-only | current |
| cSdslSturState OBJECT-TYPE This object specifies the state of the STU-R transceiver. | 1.3.6.1.4.1.9.9.155.1.3.1.4 | INTEGER {other(1), training(2), steadyState(3)} | read-only | current |
| cSdslSturDefect OBJECT-TYPE This object specifies any possible defects currently being exhibited by the STU-R. This object has the intention of supplementing ifOperStatus. | 1.3.6.1.4.1.9.9.155.1.3.1.5 | SdslStuxDefect | read-only | current |
| cSdslSturCurrRate OBJECT-TYPE This object specifies the rate the STU-R transceiver was able to obtain following training. | 1.3.6.1.4.1.9.9.155.1.3.1.6 | Integer32 (0..2320000) | read-only | current |
| cSdslSturCurrSnrMgn OBJECT-TYPE This object specifies the SNR margin as seen by this STU-R with respect to its received signal. | 1.3.6.1.4.1.9.9.155.1.3.1.7 | Gauge32 | read-only | current |
| cSdslSturCurrGain OBJECT-TYPE This object specifies gain applied to this STU-R's receiver. This object is deprecated by cSdslSturCurrGainRev which has no specified range. | 1.3.6.1.4.1.9.9.155.1.3.1.8 | Integer32 (-200..200) | read-only | deprecated |
| cSdslSturCurrOutputPwr OBJECT-TYPE This object specifies the measured total output power transmitted by this STU-R. This is the measurement that was reported during the last activation sequence. | 1.3.6.1.4.1.9.9.155.1.3.1.9 | Gauge32 | read-only | current |
| cSdslSturCurrAtn OBJECT-TYPE Measured difference in the total power transmitted by the peer STU-C and the total power received by this STU-R | 1.3.6.1.4.1.9.9.155.1.3.1.10 | Gauge32 | read-only | current |
| cSdslSturCurrGainRev OBJECT-TYPE This object specifies gain applied to this STU-R's receiver. This object deprecates by cSdslSturCurrGain and has no specified range. | 1.3.6.1.4.1.9.9.155.1.3.1.11 | Integer32 | read-only | current |
| cSdslStucPerfDataTable OBJECT-TYPE This table contains physical-layer statistics for STU-C class devices supported by the system. | 1.3.6.1.4.1.9.9.155.1.6 | not-accessible | current | |
| cSdslStucPerfDataEntry OBJECT-TYPE A set of physical-layer statistics for an STU-C class device supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | 1.3.6.1.4.1.9.9.155.1.6.1 | not-accessible | current | |
| cSdslStucPerfLOSs OBJECT-TYPE This object specifies the number of LOS failures experienced by the STU-C since agent reset. | 1.3.6.1.4.1.9.9.155.1.6.1.1 | Counter32 | read-only | current |
| cSdslStucPerfLOSQs OBJECT-TYPE This object specifies the number of LOSQ failures experienced by the STU-C since agent reset. | 1.3.6.1.4.1.9.9.155.1.6.1.2 | Counter32 | read-only | current |
| cSdslStucPerfCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-C since agent reset. | 1.3.6.1.4.1.9.9.155.1.6.1.3 | Counter32 | read-only | current |
| cSdslStucPerfESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-C since agent reset. | 1.3.6.1.4.1.9.9.155.1.6.1.4 | Counter32 | read-only | current |
| cSdslStucPerfSESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-C since agent reset. | 1.3.6.1.4.1.9.9.155.1.6.1.5 | Counter32 | read-only | current |
| cSdslStucPerfUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-C since agent reset. | 1.3.6.1.4.1.9.9.155.1.6.1.6 | Counter32 | read-only | current |
| cSdslStucPerfInits OBJECT-TYPE This object specifies the number of line initializations attempted by the STU-C since agent reset. This value includes both successful and failed attempts. | 1.3.6.1.4.1.9.9.155.1.6.1.7 | Counter32 | read-only | current |
| cSdslStucUnavailRsrcs OBJECT-TYPE This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space. | 1.3.6.1.4.1.9.9.155.1.6.1.8 | Counter32 | read-only | current |
| cSdslStucPerfValidIntervals OBJECT-TYPE The number of previous near end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute near end intervals since the interface has been online. | 1.3.6.1.4.1.9.9.155.1.6.1.9 | Integer32 (0..96) | read-only | current |
| cSdslStucPerfInvalidIntervals OBJECT-TYPE The number of near-end performance data 15-minute intervals in the range from 0 to cSdslStucPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations). | 1.3.6.1.4.1.9.9.155.1.6.1.10 | Integer32 (0..96) | read-only | current |
| cSdslStucPerfCurr15MinTimeElapse OBJECT-TYPE The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. | 1.3.6.1.4.1.9.9.155.1.6.1.11 | SdslPerfTimeElapsed (0..899) | read-only | current |
| cSdslStucPerfCurr15MinLOSs OBJECT-TYPE This object specifies the number of seconds in the current 15-minute interval when the STU-C experienced LOS. | 1.3.6.1.4.1.9.9.155.1.6.1.12 | PerfCurrentCount | read-only | current |
| cSdslStucPerfCurr15MinLOSQs OBJECT-TYPE This object specifies the number of seconds in the current 15-minute interval when the STU-C experienced LOSQ. | 1.3.6.1.4.1.9.9.155.1.6.1.13 | PerfCurrentCount | read-only | current |
| cSdslStucPerfCurr15MinCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-C in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.6.1.14 | PerfCurrentCount | read-only | current |
| cSdslStucPerfCurr15MinESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-C in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.6.1.15 | PerfCurrentCount | read-only | current |
| cSdslStucPerfCurr15MinSESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-C in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.6.1.16 | PerfCurrentCount | read-only | current |
| cSdslStucPerfCurr15MinUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-C in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.6.1.17 | PerfCurrentCount | read-only | current |
| cSdslStucPerfCurr15MinInits OBJECT-TYPE This object specifies the number of line initializations attempted by the STU-C in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.6.1.18 | PerfCurrentCount | read-only | current |
| cSdslStucPerfCurr15MinUnavlRsrcs OBJECT-TYPE This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space, in the current 15 minute interval. | 1.3.6.1.4.1.9.9.155.1.6.1.19 | PerfCurrentCount | read-only | current |
| cSdslStucPerfCurr1DayTimeElapsed OBJECT-TYPE The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. | 1.3.6.1.4.1.9.9.155.1.6.1.20 | SdslPerfTimeElapsed (0..86399) | read-only | current |
| cSdslStucPerfCurr1DayLOSs OBJECT-TYPE This object specifies the number of seconds experienced by the STU-C in the current 1-day interval when there was LOS. | 1.3.6.1.4.1.9.9.155.1.6.1.21 | SdslPerfCurrDayCount | read-only | current |
| cSdslStucPerfCurr1DayLOSQs OBJECT-TYPE This object specifies the number of seconds experienced by the STU-C in the current 1-day interval when there was LOSQ. | 1.3.6.1.4.1.9.9.155.1.6.1.22 | SdslPerfCurrDayCount | read-only | current |
| cSdslStucPerfCurr1DayCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-C in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.23 | SdslPerfCurrDayCount | read-only | current |
| cSdslStucPerfCurr1DayESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-C in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.24 | SdslPerfCurrDayCount | read-only | current |
| cSdslStucPerfCurr1DaySESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-C in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.25 | SdslPerfCurrDayCount | read-only | current |
| cSdslStucPerfCurr1DayUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-C in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.26 | SdslPerfCurrDayCount | read-only | current |
| cSdslStucPerfCurr1DayInits OBJECT-TYPE This object specifies the number of line initializations attempted by the STU-C in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.27 | SdslPerfCurrDayCount | read-only | current |
| cSdslStucPerfCurr1DayUnavlRsrcs OBJECT-TYPE This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space, in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.28 | SdslPerfCurrDayCount | read-only | current |
| cSdslStucPerfPrev1DayMoniSecs OBJECT-TYPE The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason. | 1.3.6.1.4.1.9.9.155.1.6.1.29 | Integer32 (0..86400) | read-only | current |
| cSdslStucPerfPrev1DayLOSs OBJECT-TYPE This object specifies the number of seconds in the current 1-day interval when the STU-C experienced LOS. | 1.3.6.1.4.1.9.9.155.1.6.1.30 | SdslPerfPrevDayCount | read-only | current |
| cSdslStucPerfPrev1DayLOSQs OBJECT-TYPE This object specifies the number of seconds in the previous 1-day interval when the STU-C experienced LOSQ. | 1.3.6.1.4.1.9.9.155.1.6.1.31 | SdslPerfPrevDayCount | read-only | current |
| cSdslStucPerfPrev1DayCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-C in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.32 | SdslPerfPrevDayCount | read-only | current |
| cSdslStucPerfPrev1DayESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-C in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.33 | SdslPerfPrevDayCount | read-only | current |
| cSdslStucPerfPrev1DaySESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-C in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.34 | SdslPerfPrevDayCount | read-only | current |
| cSdslStucPerfPrev1DayUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-C in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.35 | SdslPerfPrevDayCount | read-only | current |
| cSdslStucPerfPrev1DayInits OBJECT-TYPE This object specifies the number of line initializations attempted by the STU-C in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.36 | SdslPerfPrevDayCount | read-only | current |
| cSdslStucPerfPrev1DayUnavlRsrcs OBJECT-TYPE This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space, in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.6.1.37 | SdslPerfPrevDayCount | read-only | current |
| cSdslSturPerfDataTable OBJECT-TYPE This table contains physical-layer statistics for STU-R class devices supported by the system. -- Note to implementor: -- If the implementation does not support remote management -- of STU-R class devices, then the agent must respond with -- the appropriate error indicating that the instance does not -- exist; that is, 'noSuchName' in response to a SNMPv1 get -- request, and 'noSuchInstance' in response to a SNMPv2 get -- request. | 1.3.6.1.4.1.9.9.155.1.7 | not-accessible | current | |
| cSdslSturPerfDataEntry OBJECT-TYPE A set of physical-layer statistics for an STU-R class device supported by the system. There exists an entry for each ifEntry with an ifType of sdsl(96). | 1.3.6.1.4.1.9.9.155.1.7.1 | not-accessible | current | |
| cSdslSturPerfLOSs OBJECT-TYPE This object specifies the number of LOS failures experienced by the STU-R since agent reset. | 1.3.6.1.4.1.9.9.155.1.7.1.1 | Counter32 | read-only | current |
| cSdslSturPerfLOSQs OBJECT-TYPE This object specifies the number of LOSQ failures experienced by the STU-R since agent reset. | 1.3.6.1.4.1.9.9.155.1.7.1.2 | Counter32 | read-only | current |
| cSdslSturPerfCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-R since agent reset. | 1.3.6.1.4.1.9.9.155.1.7.1.3 | Counter32 | read-only | current |
| cSdslSturPerfESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-R since agent reset. | 1.3.6.1.4.1.9.9.155.1.7.1.4 | Counter32 | read-only | current |
| cSdslSturPerfSESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-R since agent reset. | 1.3.6.1.4.1.9.9.155.1.7.1.5 | Counter32 | read-only | current |
| cSdslSturPerfUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-R since agent reset. | 1.3.6.1.4.1.9.9.155.1.7.1.6 | Counter32 | read-only | current |
| cSdslSturPerfValidIntervals OBJECT-TYPE The number of previous far end intervals for which valid data was collected. The value will be 96 unless the interface was brought online within the last 24 hours, in which case the value will be the number of complete 15 minute far end intervals since the interface has been online. | 1.3.6.1.4.1.9.9.155.1.7.1.7 | Integer32 (0..96) | read-only | current |
| cSdslSturPerfInvalidIntervals OBJECT-TYPE The number of far-end performance data 15-minute intervals in the range from 0 to cSdslSturPerfValidIntervals for which no data is available. This object will typically be zero except in cases where the data for some intervals are not available (e.g., in proxy situations). | 1.3.6.1.4.1.9.9.155.1.7.1.8 | Integer32 (0..96) | read-only | current |
| cSdslSturPerfCurr15MinTimeElapse OBJECT-TYPE The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. | 1.3.6.1.4.1.9.9.155.1.7.1.9 | SdslPerfTimeElapsed (0..899) | read-only | current |
| cSdslSturPerfCurr15MinLOSs OBJECT-TYPE This object specifies the number of seconds in the current 15-minute interval when the STU-R experienced LOS. | 1.3.6.1.4.1.9.9.155.1.7.1.10 | PerfCurrentCount | read-only | current |
| cSdslSturPerfCurr15MinLOSQs OBJECT-TYPE This object specifies the number of seconds in the current 15-minute interval when the STU-R experienced LOSQ. | 1.3.6.1.4.1.9.9.155.1.7.1.11 | PerfCurrentCount | read-only | current |
| cSdslSturPerfCurr15MinCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-R in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.7.1.12 | PerfCurrentCount | read-only | current |
| cSdslSturPerfCurr15MinESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-R in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.7.1.13 | PerfCurrentCount | read-only | current |
| cSdslSturPerfCurr15MinSESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-R in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.7.1.14 | PerfCurrentCount | read-only | current |
| cSdslSturPerfCurr15MinUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-R in the current 15-minute interval. | 1.3.6.1.4.1.9.9.155.1.7.1.15 | PerfCurrentCount | read-only | current |
| cSdslSturPerfCurr1DayTimeElapsed OBJECT-TYPE The number of seconds that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current interval exceeds the maximum value, the agent will return the maximum value. | 1.3.6.1.4.1.9.9.155.1.7.1.16 | SdslPerfTimeElapsed (0..86399) | read-only | current |
| cSdslSturPerfCurr1DayLOSs OBJECT-TYPE This object specifies the number of seconds experienced by the STU-R in the current 1-day interval when there was LOS. | 1.3.6.1.4.1.9.9.155.1.7.1.17 | SdslPerfCurrDayCount | read-only | current |
| cSdslSturPerfCurr1DayLOSQs OBJECT-TYPE This object specifies the number of seconds experienced by the STU-R in the current 1-day interval when there was LOSQ. | 1.3.6.1.4.1.9.9.155.1.7.1.18 | SdslPerfCurrDayCount | read-only | current |
| cSdslSturPerfCurr1DayCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-R in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.7.1.19 | SdslPerfCurrDayCount | read-only | current |
| cSdslSturPerfCurr1DayESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-R in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.7.1.20 | SdslPerfCurrDayCount | read-only | current |
| cSdslSturPerfCurr1DaySESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-R in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.7.1.21 | SdslPerfCurrDayCount | read-only | current |
| cSdslSturPerfCurr1DayUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-R in the current 1-day interval. | 1.3.6.1.4.1.9.9.155.1.7.1.22 | SdslPerfCurrDayCount | read-only | current |
| cSdslSturPerfPrev1DayMoniSecs OBJECT-TYPE The amount of time in the previous 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring data could not be collected for any reason. | 1.3.6.1.4.1.9.9.155.1.7.1.23 | Integer32 (0..86400) | read-only | current |
| cSdslSturPerfPrev1DayLOSs OBJECT-TYPE This object specifies the number of seconds in the current 1-day interval when the STU-R experienced LOS. | 1.3.6.1.4.1.9.9.155.1.7.1.24 | SdslPerfPrevDayCount | read-only | current |
| cSdslSturPerfPrev1DayLOSQs OBJECT-TYPE This object specifies the number of seconds in the previous 1-day interval when the STU-R experienced LOSQ. | 1.3.6.1.4.1.9.9.155.1.7.1.25 | SdslPerfPrevDayCount | read-only | current |
| cSdslSturPerfPrev1DayCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-R in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.7.1.26 | SdslPerfPrevDayCount | read-only | current |
| cSdslSturPerfPrev1DayESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-R in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.7.1.27 | SdslPerfPrevDayCount | read-only | current |
| cSdslSturPerfPrev1DaySESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-R in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.7.1.28 | SdslPerfPrevDayCount | read-only | current |
| cSdslSturPerfPrev1DayUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-R in the previous 1-day interval. | 1.3.6.1.4.1.9.9.155.1.7.1.29 | SdslPerfPrevDayCount | read-only | current |
| cSdslStucIntervalTable OBJECT-TYPE This table contains physical-layer statistics intervals for STU-C class devices supported by the system. The interval tables are modeled after RFC 2493, Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals, RFC 2493 | 1.3.6.1.4.1.9.9.155.1.8 | not-accessible | current | |
| cSdslStucIntervalEntry OBJECT-TYPE A 15-miute interval of physical-layer statistics for a STU-C class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of sdsl(96). | 1.3.6.1.4.1.9.9.155.1.8.1 | not-accessible | current | |
| cSdslStucIntervalNumber OBJECT-TYPE The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional. | 1.3.6.1.4.1.9.9.155.1.8.1.1 | Integer32 (1..96) | not-accessible | current |
| cSdslStucIntervalValidData OBJECT-TYPE This object specifies whether the data for this interval is valid. | 1.3.6.1.4.1.9.9.155.1.8.1.2 | TruthValue | read-only | current |
| cSdslStucIntervalLOSs OBJECT-TYPE This object specifies the number of seconds in the interval when the STU-C experienced LOS. | 1.3.6.1.4.1.9.9.155.1.8.1.3 | PerfIntervalCount | read-only | current |
| cSdslStucIntervalLOSQs OBJECT-TYPE This object specifies the number of seconds in the interval when the STU-C experienced LOSQ. | 1.3.6.1.4.1.9.9.155.1.8.1.4 | PerfIntervalCount | read-only | current |
| cSdslStucIntervalCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-C in the interval. | 1.3.6.1.4.1.9.9.155.1.8.1.5 | PerfIntervalCount | read-only | current |
| cSdslStucIntervalESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-C in the interval. | 1.3.6.1.4.1.9.9.155.1.8.1.6 | PerfIntervalCount | read-only | current |
| cSdslStucIntervalSESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-C in the interval. | 1.3.6.1.4.1.9.9.155.1.8.1.7 | PerfIntervalCount | read-only | current |
| cSdslStucIntervalUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-C in the interval. | 1.3.6.1.4.1.9.9.155.1.8.1.8 | PerfIntervalCount | read-only | current |
| cSdslStucIntervalInits OBJECT-TYPE This object specifies the number of line initializations attempted by the STU-C in the interval. | 1.3.6.1.4.1.9.9.155.1.8.1.9 | PerfIntervalCount | read-only | current |
| cSdslStucIntervalUnavlRsrcs OBJECT-TYPE This object specifies the number of packets discarded on the STU-C due to unavailable resources, such as lack of buffer space in the interval. | 1.3.6.1.4.1.9.9.155.1.8.1.10 | PerfIntervalCount | read-only | current |
| cSdslSturIntervalTable OBJECT-TYPE This table contains physical-layer statistics intervals for STU-R class devices supported by the system. The interval tables are modeled after RFC 2493, Textual Conventions for MIB Modules Using Performance History Based on 15 Minute Intervals, RFC 2493 | 1.3.6.1.4.1.9.9.155.1.9 | not-accessible | current | |
| cSdslSturIntervalEntry OBJECT-TYPE A 15-miute interval of physical-layer statistics for a STU-R class device supported by the system. There exists up to 96 entries for each ifEntry with an ifType of sdsl(96). | 1.3.6.1.4.1.9.9.155.1.9.1 | not-accessible | current | |
| cSdslSturIntervalNumber OBJECT-TYPE The interval in which the statistics were collected, where the value of 1 represents the most recent interval, and the value of 96 represents the interval collected 24 hours ago. Intervals 2..96 are optional. | 1.3.6.1.4.1.9.9.155.1.9.1.1 | Integer32 (1..96) | not-accessible | current |
| cSdslSturIntervalValidData OBJECT-TYPE This object specifies whether the data for this interval is valid. | 1.3.6.1.4.1.9.9.155.1.9.1.2 | TruthValue | read-only | current |
| cSdslSturIntervalLOSs OBJECT-TYPE This object specifies the number of seconds in the interval when the STU-R experienced LOS. | 1.3.6.1.4.1.9.9.155.1.9.1.3 | PerfIntervalCount | read-only | current |
| cSdslSturIntervalLOSQs OBJECT-TYPE This object specifies the number of seconds in the interval when the STU-R experienced LOSQ. | 1.3.6.1.4.1.9.9.155.1.9.1.4 | PerfIntervalCount | read-only | current |
| cSdslSturIntervalCVs OBJECT-TYPE This object specifies the number of coding violations experienced by the STU-R in the interval. | 1.3.6.1.4.1.9.9.155.1.9.1.5 | PerfIntervalCount | read-only | current |
| cSdslSturIntervalESs OBJECT-TYPE This object specifies the number of errored seconds experienced by the STU-R in the interval. | 1.3.6.1.4.1.9.9.155.1.9.1.6 | PerfIntervalCount | read-only | current |
| cSdslSturIntervalSESs OBJECT-TYPE This object specifies the number of severely errored seconds experienced by the STU-R in the interval. | 1.3.6.1.4.1.9.9.155.1.9.1.7 | PerfIntervalCount | read-only | current |
| cSdslSturIntervalUASs OBJECT-TYPE This object specifies the number of unavailable seconds experienced by the STU-R in the interval. | 1.3.6.1.4.1.9.9.155.1.9.1.8 | PerfIntervalCount | read-only | current |
| cSdslLineConfProfileTable OBJECT-TYPE This table extends the adslLineConfProfileTable and contains enterprise-specific SDSL line configuration information. | 1.3.6.1.4.1.9.9.155.1.14 | not-accessible | current | |
| cSdslLineConfProfileEntry OBJECT-TYPE A configuration profile containing enterprise-specific SDSL line configuration information. | 1.3.6.1.4.1.9.9.155.1.14.1 | not-accessible | current | |
| cSdslLineMaxRate OBJECT-TYPE This object specifies the desired line rate which the STU-C will attempt to train at. | 1.3.6.1.4.1.9.9.155.1.14.1.1 | Integer32 (144000 | 272000 | 400000 | 528000 | 784000 | 1040000 | 1168000 | 1552000 | 2064000 | 2320000) | read-create | current |
| cSdslLineFramingMode OBJECT-TYPE This object specifies the desired Transmission Convergence framing structure being used by the interface. | 1.3.6.1.4.1.9.9.155.1.14.1.2 | INTEGER {none(1), other(2), hdsl(3), gShdsl(4), hdsl2(5), ds1(6)} | read-create | current |
| cSdslStucTargetSnrMgn OBJECT-TYPE This object specifies the target SNR margin. This is the desired noise margin the STU-C must achieve with a BER of 10-7 or better to successfully complete training. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. | 1.3.6.1.4.1.9.9.155.1.14.1.3 | Integer32 (0..310) | read-create | current |
| cSdslStucMaxSnrMgn OBJECT-TYPE This object specifies the maximum acceptable SNR margin. If the noise margin exceeds this level, then the STU-C should attempt to reduce its power output to optimize its operation. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. | 1.3.6.1.4.1.9.9.155.1.14.1.4 | Integer32 (0..310) | read-create | current |
| cSdslStucMinSnrMgn OBJECT-TYPE This object specifies the minimum acceptable SNR margin. If the noise margin falls below this level, the STU-C will retrain. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. | 1.3.6.1.4.1.9.9.155.1.14.1.5 | Integer32 (0..310) | read-create | current |
| cSdslStucOutputPwr OBJECT-TYPE This object specifies the transmit power level used by the STU-C. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. | 1.3.6.1.4.1.9.9.155.1.14.1.6 | Integer32 (0..310) | read-create | current |
| cSdslShdslLineMaxRate OBJECT-TYPE This object specifies the desired line rate at which the G.shdsl STU-C will attempt to train. | 1.3.6.1.4.1.9.9.155.1.14.1.7 | INTEGER {r72000(72000), r136000(136000), r200000(200000), r264000(264000), r392000(392000), r520000(520000), r776000(776000), r784000(784000), r1032000(1032000), r1160000(1160000), r1544000(1544000), r1552000(1552000), r2056000(2056000), r2312000(2312000), r2376000(2376000)} | read-create | current |
| cSdslStucPsdMaskType OBJECT-TYPE This object specifies the PSD mask type for the transceiver. For all values of the cSdslShdslLineMaxRate, the symmetric PSD masktype is selectable. Asymmetric mask is only selectable for the following rates: 776000, 784000, 1552000, 2056000, 2312000. | 1.3.6.1.4.1.9.9.155.1.14.1.8 | INTEGER {symmetric(1), asymmetric(2)} | read-create | current |
| cSdslStucAnnex OBJECT-TYPE This object specifies the operating conditions for the port of G.shdsl CO equipment . Annex A is optimized for conditions typically encountered within the North American network,whereas Annex B is optimized for conditions typically encountered within the European network. | 1.3.6.1.4.1.9.9.155.1.14.1.9 | INTEGER {annexA(1), annexB(2)} | read-create | current |
| cSdslLineEquipmentType OBJECT-TYPE This object specifies the type of the STU device ,either STU-C or STU-R | 1.3.6.1.4.1.9.9.155.1.14.1.10 | INTEGER {stuR(1), stuC(2)} | read-create | current |
| cSdslLineAutoRateEnable OBJECT-TYPE This object specifies whether the device uses the rate adaptive training mode. | 1.3.6.1.4.1.9.9.155.1.14.1.11 | TruthValue | read-create | current |
| cSdslStucThresholdSnrMgn OBJECT-TYPE This object specifies the SNR margin threshold. An appropriate alarm should be generated when the difference between the actual SNR and the SNR required to maintain BER of 10E-7 is less than this value. The value for this object must be in multiples of 10. The specified value will be rounded down to the nearest valid tenth dB level if the value is not in multiples of 10. If the agent implements the CISCO-ENTITY-ALARM-MIB, the alarm generated should be through the mechanism defined by the CISCO-ENTITY-ALARM-MIB. Furthermore, the default severity of this alarm should be 'minor'. | 1.3.6.1.4.1.9.9.155.1.14.1.12 | Integer32 (0..310) | read-create | current |
| cSdslSturAnnex OBJECT-TYPE This object specifies the operating conditions for the port of G.shdsl CPE equipment. Annex A is optimized for conditions typically encountered within the North American network,whereas Annex B is optimized for conditions typically encountered within the European network. | 1.3.6.1.4.1.9.9.155.1.14.1.13 | INTEGER {annexA(1), annexB(2)} | read-create | current |
| cSdslLineAlarmConfProfileTable OBJECT-TYPE This table extends the adslLineAlarmConfProfileTable and contains enterprise-specific SDSL line configuration information pertaining to alarms. | 1.3.6.1.4.1.9.9.155.1.15 | not-accessible | current | |
| cSdslLineAlarmConfProfileEntry OBJECT-TYPE A configuration profile containing enterprise-specific SDSL line configuration information pertaining to alarms | 1.3.6.1.4.1.9.9.155.1.15.1 | not-accessible | current | |
| cSdslStucThreshMinRate OBJECT-TYPE This object specifies the line rate threshold. When the agent observes the line rate fall below this value, an appropriate alarm should be generated. The default value for this object should be the value of the cSdslLineMaxRate object. If the agent implements the CISCO-ENTITY-ALARM-MIB, the alarm generated should be through the mechanism defined by the CISCO-ENTITY-ALARM-MIB. Furthermore, the default severity of this alarm should be 'minor'. | 1.3.6.1.4.1.9.9.155.1.15.1.1 | Integer32 (0..310) | read-create | current |
| cSdslStucThreshMinSnrMgn OBJECT-TYPE This object specifies the SNR margin threshold. When the agent observes the received SNR margin fall below this value, an appropriate alarm should be generated. If the agent implements the CISCO-ENTITY-ALARM-MIB, the alarm generated should be through the mechanism defined by the CISCO-ENTITY-ALARM-MIB. Furthermore, the default severity of this alarm should be 'minor'. | 1.3.6.1.4.1.9.9.155.1.15.1.2 | Integer32 (0..310) | read-create | current |
| ciscoSdslLineMIBNotificationsPrefix OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.155.2 | |||
| ciscoSdslLineMIBNotifications OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.155.2.0 | |||
| ciscoSdslLineMIBConformance OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.155.3 | |||
| ciscoSdslLineMIBCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.155.3.1 | |||
| ciscoSdslLineMIBGroups OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.155.3.2 |
Conformance
| Name | OID | Status |
|---|---|---|
| ciscoSdslLineMIBStucCompliance MODULE-COMPLIANCE The compliance statement for entities that implement the CISCO-SDSL-LINE-MIB. Implementation of this MIB is mandatory for any platform that supports one or more SDSL line interfaces. This specification is replaced by ciscoSdslLineMIBStucComplianceRev1 | 1.3.6.1.4.1.9.9.155.3.1.1 | deprecated |
| ciscoSdslLineMIBSturCompliance MODULE-COMPLIANCE The compliance statement for entities that implement the CISCO-SDSL-LINE-MIB and manage SDSL STU-R class devices. Implementation of this MIB is mandatory for any platform that supports one or more SDSL line interfaces. This specification is replaced by ciscoSdslLineMIBSturComplianceRev1. | 1.3.6.1.4.1.9.9.155.3.1.2 | deprecated |
| ciscoSdslLineMIBStucComplianceRev1 MODULE-COMPLIANCE The compliance statement for entities that implement the CISCO-SDSL-LINE-MIB. Implementation of this MIB is mandatory for any platform that supports one or more SDSL line interfaces. | 1.3.6.1.4.1.9.9.155.3.1.3 | current |
| ciscoSdslLineMIBSturComplianceRev1 MODULE-COMPLIANCE The compliance statement for entities that implement the CISCO-SDSL-LINE-MIB and manage SDSL STU-R class devices. Implementation of this MIB is mandatory for any platform that supports one or more SDSL line interfaces. | 1.3.6.1.4.1.9.9.155.3.1.4 | current |
| cSdslStucBasicGroup OBJECT-GROUP A collection of managed objects defining the basic operation of an STU-C (i.e., no rate adaptation). This specification is replaced by cSdslStucBasicGroupRev1. | 1.3.6.1.4.1.9.9.155.3.2.1 | deprecated |
| cSdslSturBasicGroup OBJECT-GROUP A collection of managed objects defining the basic operation of an STU-R.This specification is replaced by cSdslSturBasicGroupRev1 | 1.3.6.1.4.1.9.9.155.3.2.2 | deprecated |
| cSdslSturGroup OBJECT-GROUP A collection of managed objects defining the capability to remotely manage a STU-R. This is replaced by cSdslSturGroupRev1. | 1.3.6.1.4.1.9.9.155.3.2.3 | deprecated |
| cSdslStucPMCounterGroup OBJECT-GROUP A collection of managed objects defining basic near-end performance monitoring capability. | 1.3.6.1.4.1.9.9.155.3.2.4 | current |
| cSdslStucPM15MinIntervalGroup OBJECT-GROUP A collection of managed objects defining near-end performance data collection capability using 15-minute intervals. | 1.3.6.1.4.1.9.9.155.3.2.5 | current |
| cSdslStucPM1DayIntervalGroup OBJECT-GROUP A collection of managed objects defining near-end performance data collection capability using 1-day intervals. | 1.3.6.1.4.1.9.9.155.3.2.6 | current |
| cSdslSturPMCounterGroup OBJECT-GROUP A collection of managed objects defining basic far-end performance monitoring capability. | 1.3.6.1.4.1.9.9.155.3.2.7 | current |
| cSdslSturPM15MinIntervalGroup OBJECT-GROUP A collection of managed objects defining far-end performance data collection capability using 15-minute intervals. | 1.3.6.1.4.1.9.9.155.3.2.8 | current |
| cSdslSturPM1DayIntervalGroup OBJECT-GROUP A collection of managed objects defining far-end performance data collection capability using 1-day intervals. | 1.3.6.1.4.1.9.9.155.3.2.9 | current |
| cSdslStucRateAdaptiveGroup OBJECT-GROUP A collection of managed objects defining rate adaptive operation of an STU-C. | 1.3.6.1.4.1.9.9.155.3.2.10 | current |
| cSdslStucAlarmConfProfileGroup OBJECT-GROUP A collection of traps generated by the agent to signal threshold alarms. | 1.3.6.1.4.1.9.9.155.3.2.11 | current |
| cSdslStucBasicGroupRev1 OBJECT-GROUP A collection of managed objects defining the basic operation of an STU-C. This specification is replaced by cSdslStucBasicGroupRev2. | 1.3.6.1.4.1.9.9.155.3.2.12 | deprecated |
| cSdslSturBasicGroupRev1 OBJECT-GROUP A collection of managed objects defining the basic operation of an STU-R. This specification is replaced by cSdslSturBasicGroupRev2 | 1.3.6.1.4.1.9.9.155.3.2.13 | deprecated |
| cSdslStucBasicGroupRev2 OBJECT-GROUP A collection of managed objects defining the basic operation of an STU-C. | 1.3.6.1.4.1.9.9.155.3.2.14 | current |
| cSdslSturBasicGroupRev2 OBJECT-GROUP A collection of managed objects defining the basic operation of an STU-R. | 1.3.6.1.4.1.9.9.155.3.2.15 | current |
| cSdslSturGroupRev1 OBJECT-GROUP A collection of managed objects defining the capability to remotely manage a STU-R. | 1.3.6.1.4.1.9.9.155.3.2.16 | current |