MIBs Depot

CISCO-MGX82XX-DSX1-MIB

Registered at
1.3.6.1.4.1.351.110.4.3.1.1
1.3.6.1.4.1.351.110.4.3.1.2
1.3.6.1.4.1.351.110.4.3.1.3
1.3.6.1.4.1.351.110.4.3.1.4
1.3.6.1.4.1.351.150.58
Last updated
2003-03-31 00:00
Organization
Cisco Systems, Inc.
Revisions
2003-03-31 00:00
Namespace
cisco
Source file
CISCO-MGX82XX-DSX1-MIB
Digest
sha256:739b266a2532060595e2b6c8eb0cce09015fba13a056e24c89a924188ef88273

Description

The MIB module to configure DS1/E1 interface objects. This mib also contains the alarm configuration of DS1/E1 interfaces. This mib is supported in T1/E1 service modules.

Contact

Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wanatm@cisco.com

Imports

FromSymbols
BASIS-MIBdsx1Line
CISCOWAN-SMIciscoWan
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter32, Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, iso
SNMPv2-TCDisplayString, TEXTUAL-CONVENTION

Imported by

1 module(s) in this corpus import this one.

Load order

Every file a consumer needs in order to load this module, dependencies first.

BASIS-MIB
CISCO-MGX82XX-DSX1-MIB
CISCOWAN-SMI
SNMPv2-CONF
SNMPv2-SMI
SNMPv2-TC

Objects

NameOIDSyntaxAccessStatus
dsx1CnfGrp
OBJECT-IDENTITY
1.3.6.1.4.1.351.110.4.3.1.1
dsx1CnfGrpTable
OBJECT-TYPE
The DS1/E1 Configuration table. The table size is given by the value of lineNumofValidEntries
1.3.6.1.4.1.351.110.4.3.1.1.1not-accessiblecurrent
dsx1CnfGrpEntry
OBJECT-TYPE
An entry in the DS1 Configuration table.
1.3.6.1.4.1.351.110.4.3.1.1.1.1not-accessiblecurrent
lineNum
OBJECT-TYPE
This object is the identifier of a DS1/E1 Interface on a managed device. If there is an ifEntry that is directly associated with this and only this DS1/E1 interface, it should have the same value as ifIndex. Otherwise, number the ds1LineIndices with an unique identifier following the rules of choosing a number that is greater than ifNumber and numbering the inside interfaces (e.g., equipment side) with even numbers and outside interfaces (e.g, network side) with odd numbers. The supported ranges depend upon the type of the card(4 port/8 port etc): For 4 port card : 1 - 4 For 8 port card : 1 - 8 For 2 Port Channelized card : 56 (28*2).
1.3.6.1.4.1.351.110.4.3.1.1.1.1.1Integer32 (1..2147483647)read-onlycurrent
lineConnectorType
OBJECT-TYPE
This variable indicates the connector as well as the backcard type. 1 = T1; 2 = E1. This field is set to unused(4) for FRSM-VHS cards.
1.3.6.1.4.1.351.110.4.3.1.1.1.1.2INTEGER {db15(1), bnc(2), rj48(3), unused(4), smb(5)}read-writecurrent
lineEnable
OBJECT-TYPE
This variable disables, enables or modifies a line 1 - disable 2 - enable 3 - modify In FRSM-2CT3, if the DS3 line is enabled, then the DS1 channels for that line will all be automatically enabled. No independent enable/disable is allowed for each of the 28 DS1 lines in FRSM-2CT3.
1.3.6.1.4.1.351.110.4.3.1.1.1.1.3INTEGER {disable(1), enable(2), modify(3)}read-writecurrent
lineType
OBJECT-TYPE
This variable indicates the variety of DS1 Line implementing this circuit. The type of circuit affects the number of bits per second that the circuit can reasonably carry, as well as the interpretation of the usage and error statistics. The values, in sequence, describe: TITLE: SPECIFICATION: dsx1ESF Extended SuperFrame DS1 dsx1D4 AT&T D4 format DS1 dsx1E1 CCITT Recommendation G.704 (Table 4a) dsx1E1-CRC CCITT Recommendation G.704 (Table 4b) dsxE1-MF G.704 (Table 4a) with TS16 multiframing enabled dsx1E1-CRC-MF G.704 (Table 4b) with TS16 multiframing enabled dsx1E1clearchannel E1 clear channel, all DS0s can be used dsx1E1Q50 G.704 (table 14) In TS16 bits 5,7,8 will be set to 100 for all other cases bits 5,7,8 will have a value of 111. dsx1E1Q50CRC same as dsx1E1Q50 but with CRC. NOTE: All E1, E1-CRC, E1-MF or E1-CRC-MF are using DS0 on slot 1 for signaling and E1-MF or E1-CRC-MF use DS0 on slot 17 for synchronization. (Slot 1 and 16 is based on index 1 to 32 DS0) All DS0s can be used for any port when lineType is dsx1E1clearchannel. On a CESM card, only 'dsx1E1clearchannel' option is supported. When the lineType is dsx1E1Q50 the bits 5,7,8 of TS16 of frame zero will be forced to 100 else it will be 111. The default value for T1 is 'dsx1ESF' and for E1 is 'dsx1E1CCS'.
1.3.6.1.4.1.351.110.4.3.1.1.1.1.4INTEGER {dsx1ESF(1), dsx1D4(2), dsx1E1(3), dsx1E1CRC(4), dsx1E1MF(5), dsx1E1CRC-MF(6), dsx1E1clearchannel(7), dsx1E1Q50(8), dsx1E1Q50CRC(9)}read-writecurrent
lineCoding
OBJECT-TYPE
This variable describes the variety of Zero Code Suppression used on the link, which in turn affects a number of its characteristics. dsx1JBZS(1): refers the Jammed Bit Zero suppression in which the AT&T specification of at least one pulse every 8 bit periods is literally implemented by forcing a pulse in bit 8 of each channel. Thus, only seven bits per chan- nel, or 1.344 Mbps, is available for data. dsx1B8ZS(2): refers to the use of a specified pattern of normal bits and bipolar violations which are used to replace a sequence of eight zero bits. E1 links, with or without CRC, use dsx1HDB3 or dsx1AMI. dsx1AMI(4): refers to a mode wherein no zero code suppression is present and the line encoding does not solve the problem directly. In this application, the higher layer must provide data which meets or exceeds the pulse density requirements, such as inverting HDLC data. The default value for T1 is 'dsx1JBZS' and for E1 is 'dsx1HDB3'. This field is not applicable for FRSM-VHS cards and is set to notUsed(5).
1.3.6.1.4.1.351.110.4.3.1.1.1.1.5INTEGER {dsx1JBZS(1), dsx1B8ZS(2), dsx1HDB3(3), dsx1AMI(4), unused(5)}read-writecurrent
lineLength
OBJECT-TYPE
This is not a standard RFC 1407 DS1 variable, it is specific to BASIS implementation. It specifies the line length: 1 - 0 to 110 ft (T1 line only) 2 - 110 to 220 ft (T1 line only) 3 - 220 to 330 ft (T1 line only) 4 - 330 to 440 ft (T1 line only) 5 - 440 to 550 ft (T1 line only) 6 - 550 to 660 ft (T1 line only) 7 - greater than 660 ft (T1 line only) 8 - 75 ohms (E1 line only (BNC)) 9 - 120 ohms (E1 line only (DB-15)) The default value for T1 is 1, for E1, if the connector type is DB15 then the default is 9, if BNC, it's 8. For FRSM-2CT3, the line length of DS1 has no meaning as there are no physical DS1 lines. So, for this card, the value is set to notRequired (16).
1.3.6.1.4.1.351.110.4.3.1.1.1.1.6INTEGER {lineLength0To110Feet(1), lineLength110To220Feet(2), lineLength220To330Feet(3), lineLength330To440Feet(4), lineLength440To550Feet(5), lineLength550To660Feet(6), lineLength660FeetPlus(7), lineLength-75-Ohm(8), lineLength-120-Ohm(9), lineLength0To131Feet(10), lineLength131To262Feet(11), lineLength262To393Feet(12), lineLength393To524Feet(13), lineLength524To655Feet(14), lineLength655FeetPlus(15), notRequired(16)}read-writecurrent
lineXmtClockSource
OBJECT-TYPE
The source of Transmit Clock. loopTiming(1): indicates that the recovered receive clock is used as the transmit clock. localTiming(2): indicates that a local clock source is used.
1.3.6.1.4.1.351.110.4.3.1.1.1.1.7INTEGER {loopTiming(1), localTiming(2)}read-writecurrent
lineLoopbackCommand
OBJECT-TYPE
This variable represents the loopback confi- guration of the DS1 interface. Agents support- ing read/write access should return badValue in response to a requested loopback state that the interface does not support. The values mean: dsx1NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. dsx1RemoteLoop The received signal at this interface is looped through the device. Typically the received signal is looped back for retransmission after it has passed through the device's framing function. dsx1LocalLoop The local data is looped back dsx1PayloadLoop This will loop only the payload and not framing/sync bit.
1.3.6.1.4.1.351.110.4.3.1.1.1.1.8INTEGER {dsx1NoLoop(1), dsx1RemoteLoop(2), dsx1LocalLoop(3), dsx1PayloadLoop(4)}read-writecurrent
lineSendCode
OBJECT-TYPE
This variable indicates what type of code is being sent across the DS1 interface by the dev- ice. The values mean: dsx1SendNoCode sending looped or normal data dsx1SendLineCode sending a request for a line loopback dsx1SendPayloadCode sending a request for a payload loopback dsx1SendResetCode sending a loopback termination request
1.3.6.1.4.1.351.110.4.3.1.1.1.1.9INTEGER {dsx1SendNoCode(1), dsx1SendLineCode(2), dsx1SendPayloadCode(3), dsx1SendResetCode(4)}read-writecurrent
lineUsedTimeslotsBitMap
OBJECT-TYPE
Bit map of used DS0 for this line.
1.3.6.1.4.1.351.110.4.3.1.1.1.1.10Integer32 (0..2147483647)read-onlycurrent
lineLoopbackCodeDetection
OBJECT-TYPE
Enable detection of line Loopback Codes
1.3.6.1.4.1.351.110.4.3.1.1.1.1.11INTEGER {codeDetectDisabled(1), codeDetectEnabled(2)}read-writecurrent
lineBERTEnable
OBJECT-TYPE
This variable enables Bit Error Rate Testing(BERT).
1.3.6.1.4.1.351.110.4.3.1.1.1.1.12INTEGER {disable(1), enable(2)}read-writecurrent
lineBERTPattern
OBJECT-TYPE
This variable determines BERT pattern to transmit
1.3.6.1.4.1.351.110.4.3.1.1.1.1.13INTEGER {allZeros(1), allOnes(2), alternateONeZero(3), doubleOneZero(4), userOneWords(5), userTwoWords(6), userThreeWords(7), userFourWords(8), fifteenBit(9), twentyBit(10), twentyBitQRSS(11), twentythreeBit(12)}read-writecurrent
lineBERTResult
OBJECT-TYPE
This shows the result of the BERT.
1.3.6.1.4.1.351.110.4.3.1.1.1.1.14INTEGER {failed(1), passed(2)}read-writecurrent
bERTResultClrButton
OBJECT-TYPE
This clears the result of the BERT.
1.3.6.1.4.1.351.110.4.3.1.1.1.1.15INTEGER {noaction(1), clear(2)}read-writecurrent
lineNumofValidEntries
OBJECT-TYPE
The number of DS1 configuration entries (regardless of their current configuration) in the dsx1CnfGrpTable.
1.3.6.1.4.1.351.110.4.3.1.1.2Integer32 (0..128)read-onlycurrent
dsx1AlmCnfGrp
OBJECT-IDENTITY
1.3.6.1.4.1.351.110.4.3.1.2
dsx1AlmCnfGrpTable
OBJECT-TYPE
The DS1 interface alarm configuration table.
1.3.6.1.4.1.351.110.4.3.1.2.1not-accessiblecurrent
dsx1AlmCnfGrpEntry
OBJECT-TYPE
An entry in the DS1 Alarm Configuration table.
1.3.6.1.4.1.351.110.4.3.1.2.1.1not-accessiblecurrent
almCnfLineNum
OBJECT-TYPE
This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.1Integer32 (1..2147483647)read-onlycurrent
redSeverity
OBJECT-TYPE
This variable is used to setup the severity of RED alarm. So when RED alarm is detected by the card, an alarm with appropriate severity status will be sent.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.2INTEGER {minor(1), major(2)}read-writecurrent
rAISeverity
OBJECT-TYPE
This variable is used to setup the severity of RAI alarm. So when LOS alarm is detected the card, an alarm with appropriate severity status will be sent.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.3INTEGER {minor(1), major(2)}read-writecurrent
nEAlarmUpCount
OBJECT-TYPE
This parameter specifies the integration counter, the local alarms are LOS and LOF. Default value is 6 and update counter every 10 ms to reach the threshold set in threshold object. This is the up counter.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.4Integer32 (0..2147483647)read-writecurrent
nEAlarmDownCount
OBJECT-TYPE
This parameter specifies the integration counter, the Near-End alarms are LOS and LOF. Default value is 1 and update counter every 10 ms to reach 0. This is the down counter.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.5Integer32 (0..2147483647)read-writecurrent
nEAlarmThreshold
OBJECT-TYPE
The value set in this object determines the value to declare Near-End alarm. A count of 1500 gives 2.5 sec to declare LOS with an up count value of 6.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.6Integer32 (0..2147483647)read-writecurrent
fEAlarmUpCount
OBJECT-TYPE
This parameter specifies the integration counter, the Far-End alarms are AIS and YEL. Default value is 6 and update counter 10 ms to reach the threshold set in threshold object. This is the up counter.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.7Integer32 (0..2147483647)read-writecurrent
fEAlarmDownCount
OBJECT-TYPE
This parameter specifies the integration counter, the Far-End alarms are AIS and YEL. Default value is 1 and update counter every 10 ms to reach 0. This is the down counter.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.8Integer32 (0..2147483647)read-writecurrent
fEAlarmThreshold
OBJECT-TYPE
The value set in this object determines the value to declare Far-End alarm. A count of 1500 gives 2.5 secs to declare LOS with an up count value of 6.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.9Integer32 (0..2147483647)read-writecurrent
statisticalAlarmSeverity
OBJECT-TYPE
This variable is used to setup the severity of Statistical alarm. So when any statistical alarm is detected by the card, an alarm with appropriate severity status will be sent.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.10INTEGER {minor(1), major(2), inhibit(3)}read-writecurrent
lCV15MinThreshold
OBJECT-TYPE
Code Violation - is the occurrence of a received CRC-6 code that is not identical to the corresponding locally. calculated code. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.11Integer32 (0..2147483647)read-writecurrent
lCV24HrThreshold
OBJECT-TYPE
Code Violation - is the occurence of a received CRC-6 code that is not identical to the corresponding locally. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.12Integer32 (0..2147483647)read-writecurrent
lES15MinThreshold
OBJECT-TYPE
Errored Second - is any second with at least one code violation. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.13Integer32 (0..2147483647)read-writecurrent
lES24HrThreshold
OBJECT-TYPE
Errored Second - is any second with at least one code violation. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.14Integer32 (0..2147483647)read-writecurrent
lSES15MinThreshold
OBJECT-TYPE
Severely Errored Second - is any second with 15 or more code violations. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.15Integer32 (0..2147483647)read-writecurrent
lSES24HrThreshold
OBJECT-TYPE
Severely Errored Second - is any second with 15 or more code violations. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.16Integer32 (0..2147483647)read-writecurrent
cRC15MinThreshold
OBJECT-TYPE
The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.17Integer32 (0..2147483647)read-writecurrent
cRC24HrThreshold
OBJECT-TYPE
The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.18Integer32 (0..2147483647)read-writecurrent
cRCES15MinThreshold
OBJECT-TYPE
The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.19Integer32 (0..2147483647)read-writecurrent
cRCES24HrThreshold
OBJECT-TYPE
The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.20Integer32 (0..2147483647)read-writecurrent
cRCSES15MinThreshold
OBJECT-TYPE
The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.21Integer32 (0..2147483647)read-writecurrent
cRCSES24HrThreshold
OBJECT-TYPE
The value set in this object determines the value when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.22Integer32 (0..2147483647)read-writecurrent
sEFS15MinThreshold
OBJECT-TYPE
Severely Errored Framing Second - is a count of one-second intervals containing one or more SEF events. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.23Integer32 (0..2147483647)read-writecurrent
sEFS24HrThreshold
OBJECT-TYPE
Severely Errored Framing Second - is a count of one-second intervals containing one or more SEF events. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.24Integer32 (0..2147483647)read-writecurrent
aISS15MinThreshold
OBJECT-TYPE
Alarm Indication Signal Second - is a count of one-second intervals containing one or more incoming AIS. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.25Integer32 (0..2147483647)read-writecurrent
aISS24HrThreshold
OBJECT-TYPE
Alarm Indication Signal Second - is a count of one-second intervals containing one or more incoming AIS. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.26Integer32 (0..2147483647)read-writecurrent
uAS15MinThreshold
OBJECT-TYPE
Unavailable Second - is a count of seconds during which the DS1 Layer service is unavailable. The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.
1.3.6.1.4.1.351.110.4.3.1.2.1.1.27Integer32 (0..2147483647)read-writecurrent
uAS24HrThreshold
OBJECT-TYPE
Unavailable Second - is a count of seconds during which the DS1 Layer service is unavailable. The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval
1.3.6.1.4.1.351.110.4.3.1.2.1.1.28Integer32 (0..2147483647)read-writecurrent
dsx1AlmGrp
OBJECT-IDENTITY
1.3.6.1.4.1.351.110.4.3.1.3
dsx1AlmGrpTable
OBJECT-TYPE
The DS1 interface alarm configuration table.
1.3.6.1.4.1.351.110.4.3.1.3.1not-accessiblecurrent
dsx1AlmGrpEntry
OBJECT-TYPE
An entry in the DS1 Alarm table. Each entry represents the current, 15 minute and 24 Hour bucket intervals for different performance parameters.
1.3.6.1.4.1.351.110.4.3.1.3.1.1not-accessiblecurrent
almLineNum
OBJECT-TYPE
This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.1Integer32 (1..2147483647)read-onlycurrent
lineAlarmState
OBJECT-TYPE
This variable is a bitmap of the DSX1 Line Alarms. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 Receiving RAI 1 Transmitting RAI 2 Receiving AIS 3 Transmitting AIS 4 Receiving OOF 5 Receiving LOS 6 Near End Local Loopback in effect 7 Near End Remote Loopback in effect 8 Near End Remote Payload Loopback 9 Receiving CRC MF OOF (E1) 10 Receiving Sig MF OOF (E1) 11 Receiving MF RAI (E1) 12 Receiving MF AIS (E1) 13 BERT in effect 14 Far End Remote Loopback in effect 15 Detected Near End Remote Loopback in effect
1.3.6.1.4.1.351.110.4.3.1.3.1.1.2Integer32 (0..65535)read-onlycurrent
lineStatisticalAlarmState
OBJECT-TYPE
This variable is a bitmap of the DSX1 Line Statistical Alarms. A value of zero indicates no alarms. Itemized below are the individual alarm bits: BitPosition Alarm ----------- ----- 0 LCV 15 minute threshold exceeded 1 LCV 24 hour threshold exceeded 2 LES 15 minute threshold exceeded 3 LES 24 hour threshold exceeded 4 LSES 15 minute threshold exceeded 5 LSES 24 hour threshold exceeded 6 CRC 15 minute threshold exceeded 7 CRC 24 hour threshold exceeded 8 CRCES 15 minute threshold exceeded 9 CRCES 24 hour threshold exceeded 10 CRCSES 15 minute threshold exceeded 11 CRCSES 24 hour threshold exceeded 12 SEFS 15 minute threshold exceeded 13 SEFS 24 hour threshold exceeded 14 AISS 15 minute threshold exceeded 15 AISS 24 hour threshold exceeded 16 UAS 15 minute threshold exceeded 17 UAS 24 hour threshold exceeded.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.3Integer32 (0..2147483647)read-onlycurrent
lCVCurrent
OBJECT-TYPE
This counter counts the number of Line code violations encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.4Counter32read-onlycurrent
lCV15MinBucket
OBJECT-TYPE
The counter associated with the number of Line code violations in the last 15 minute period encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.5Counter32read-onlycurrent
lCV24HrBucket
OBJECT-TYPE
The counter associated with the number of Line code violations in the last 24 hour period encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.6Counter32read-onlycurrent
lESCurrent
OBJECT-TYPE
This counter counts the number of Line code violations Errored Seconds encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.7Counter32read-onlycurrent
lES15MinBucket
OBJECT-TYPE
This counter counts the number of Line code violations Errored Seconds in the last 15 minutes encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.8Counter32read-onlycurrent
lES24HrBucket
OBJECT-TYPE
This counter counts the number of Line code violations Errored Seconds in the last 24 hours encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.9Counter32read-onlycurrent
lSESCurrent
OBJECT-TYPE
This counter counts the number of Line code violations Severely Errored Seconds encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.10Counter32read-onlycurrent
lSES15MinBucket
OBJECT-TYPE
This counter counts the number of LCV Severely Errored Seconds in the last 15 minutes encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.11Counter32read-onlycurrent
lSES24HrBucket
OBJECT-TYPE
This counter counts the number of LCV Severely Errored Seconds in the last 24 hours encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.12Counter32read-onlycurrent
cRCCurrent
OBJECT-TYPE
This counter counts the number of P Bit code violations encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.13Counter32read-onlycurrent
cRC15MinBucket
OBJECT-TYPE
This counter counts the number of P Bit code violations in the last 15 minutes encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.14Counter32read-onlycurrent
cRC24HrBucket
OBJECT-TYPE
This counter counts the number of P Bit code violations in the last 24 hours encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.15Counter32read-onlycurrent
cRCESCurrent
OBJECT-TYPE
This counter counts the number of PCV Errored Seconds encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.16Counter32read-onlycurrent
cRCES15MinBucket
OBJECT-TYPE
This counter counts the number of PCV Errored Seconds in the last 15 minutes encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.17Counter32read-onlycurrent
cRCES24HrBucket
OBJECT-TYPE
This counter counts the number of PCV Errored Seconds in the last 24 hours encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.18Counter32read-onlycurrent
cRCSESCurrent
OBJECT-TYPE
This counter counts the number of P Bit code violations Severely Errored Seconds encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.19Counter32read-onlycurrent
cRCSES15MinBucket
OBJECT-TYPE
This counter counts the number of PCV Severely Errored Seconds in the last 15 minutes encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.20Counter32read-onlycurrent
cRCSES24HrBucket
OBJECT-TYPE
This counter counts the number of PCV Severely Errored Seconds in the last 24 hours encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.21Counter32read-onlycurrent
sEFSCurrent
OBJECT-TYPE
This counter counts the number of Severely Errored Framing Seconds encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.22Counter32read-onlycurrent
sEFS15MinBucket
OBJECT-TYPE
This counter counts the number of Severely Errored Framing Seconds in the last 15 minutes encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.23Counter32read-onlycurrent
sEFS24HrBucket
OBJECT-TYPE
This counter counts the number of Severely Errored Framing Seconds in the last 24 hours encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.24Counter32read-onlycurrent
aISSCurrent
OBJECT-TYPE
This counter counts the number of AIS Severely Errored Seconds encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.25Counter32read-onlycurrent
aISS15MinBucket
OBJECT-TYPE
This counter counts the number of AIS Severely Errored Seconds in the last 15 minutes encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.26Counter32read-onlycurrent
aISS24HrBucket
OBJECT-TYPE
This counter counts the number of AIS Severely Errored Seconds in the last 24 hours encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.27Counter32read-onlycurrent
uASCurrent
OBJECT-TYPE
This counter counts the number of Unavailable Seconds encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.28Counter32read-onlycurrent
uAS15MinBucket
OBJECT-TYPE
This counter counts the number of Unavailable Seconds in the last 15 minutes encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.29Counter32read-onlycurrent
uAS24HrBucket
OBJECT-TYPE
This counter counts the number of Unavailable Seconds in the last 24 hours encountered by the interface.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.30Counter32read-onlycurrent
percentEFS
OBJECT-TYPE
This counter counts the %LCV Error Free Seconds.
1.3.6.1.4.1.351.110.4.3.1.3.1.1.31Integer32 (0..100)read-onlycurrent
alarmClrButton
OBJECT-TYPE
This variable is used to clear all the alarms for the line. 1 = No action 2 = Clear alarm
1.3.6.1.4.1.351.110.4.3.1.3.1.1.32INTEGER {noaction(1), clear(2)}read-writecurrent
dsx1CntGrp
OBJECT-IDENTITY
1.3.6.1.4.1.351.110.4.3.1.4
dsx1CntGrpTable
OBJECT-TYPE
The DS1 Counter table. This table contains statistics since the system was up or last re-initialization.
1.3.6.1.4.1.351.110.4.3.1.4.1not-accessiblecurrent
dsx1CntGrpEntry
OBJECT-TYPE
An entry in the DS1 counter table.
1.3.6.1.4.1.351.110.4.3.1.4.1.1not-accessiblecurrent
cntLineNum
OBJECT-TYPE
This object identifies the DS1/E1 interface. The value for this object must be same as the value of lineNum from dsx1CnfGrpTable.
1.3.6.1.4.1.351.110.4.3.1.4.1.1.1Integer32 (1..2147483647)read-onlycurrent
rcvLOSCount
OBJECT-TYPE
The number of times the Loss of Signal was detected with or without integrating to LOS alarm.
1.3.6.1.4.1.351.110.4.3.1.4.1.1.2Counter32read-onlycurrent
rcvOOFCount
OBJECT-TYPE
The number of times the Out of Frame was detected with or without integrating to OOF alarm.
1.3.6.1.4.1.351.110.4.3.1.4.1.1.3Counter32read-onlycurrent
rcvRAICount
OBJECT-TYPE
The number of times Yellow Alarms was detected with or without integrating to RAI alarm.
1.3.6.1.4.1.351.110.4.3.1.4.1.1.4Counter32read-onlycurrent
rcvFECount
OBJECT-TYPE
The number of Framing Pattern Errors encountered by a DS1 interface.
1.3.6.1.4.1.351.110.4.3.1.4.1.1.5Counter32read-onlycurrent
counterClearButton
OBJECT-TYPE
This variable is used to clear all the counters.
1.3.6.1.4.1.351.110.4.3.1.4.1.1.6INTEGER {noaction(1), clear(2)}read-writecurrent
cmDsx1MIBConformance
OBJECT-IDENTITY
1.3.6.1.4.1.351.150.58.2
cmDsx1MIBGroups
OBJECT-IDENTITY
1.3.6.1.4.1.351.150.58.2.1
cmDsx1MIBCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.351.150.58.2.2

Conformance

NameOIDStatus
cmDsx1GeneralGroup
OBJECT-GROUP
The collection of objects used for DS1/E1 interfaces.
1.3.6.1.4.1.351.150.58.2.1.1current
cmDsx1ConfGroup
OBJECT-GROUP
The collection of objects used for DS1/E1 interface configuration.
1.3.6.1.4.1.351.150.58.2.1.2current
cmDsx1CountGroup
OBJECT-GROUP
The collection of objects related to DS1/E1 statistics.
1.3.6.1.4.1.351.150.58.2.1.3current
cmDsx1AlarmConfGroup
OBJECT-GROUP
The collection of objects used for DS1/E1 Alarm threshold configuration.
1.3.6.1.4.1.351.150.58.2.1.4current
cmDsx1AlarmGroup
OBJECT-GROUP
The collection of objects used for DS1/E1 Alarm configuration.
1.3.6.1.4.1.351.150.58.2.1.5current
cmDsx1Compliance
MODULE-COMPLIANCE
The compliance statement for objects related to DS1/E1 mib.
1.3.6.1.4.1.351.150.58.2.2.1current