MIBs Depot

CISCO-LWAPP-SYS-MIB

Registered at
1.3.6.1.4.1.9.9.618
Last updated
2018-07-03 00:00
Organization
Cisco Systems Inc.
Revisions
2018-07-03 00:00, 2018-04-24 00:00, 2017-05-03 00:00, 2012-06-18 00:00, 2010-02-09 00:00, 2007-10-17 00:00, 2007-03-14 00:00
Namespace
cisco
Source file
CISCO-LWAPP-SYS-MIB
Digest
sha256:565bb3c3154f96e0a25ce972ce25ce07dd9f01c43b94e1754a561ce48ee8054d

Description

This MIB is intended to be implemented on all those devices operating as Central controllers, that terminate the Light Weight Access Point Protocol tunnel from Cisco Light-weight LWAPP Access Points. This MIB provides global configuration and status information for the controller. All general system related information is presented in this MIB. The relationship between CC and the LWAPP APs can be depicted as follows: +......+ +......+ +......+ + + + + + + + CC + + CC + + CC + + + + + + + +......+ +......+ +......+ .. . . .. . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + AP + + AP + + AP + + AP + + + + + + + + + +......+ +......+ +......+ +......+ . . . . . . . . . . . . . . . . . . . +......+ +......+ +......+ +......+ + + + + + + + + + MN + + MN + + MN + + MN + + + + + + + + + +......+ +......+ +......+ +......+ The LWAPP tunnel exists between the controller and the APs. The MNs communicate with the APs through the protocol defined by the 802.11 standard. LWAPP APs, upon bootup, discover and join one of the controllers and the controller pushes the configuration, that includes the WLAN parameters, to the LWAPP APs. The APs then encapsulate all the 802.11 frames from wireless clients inside LWAPP frames and forward the LWAPP frames to the controller. GLOSSARY Access Point ( AP ) An entity that contains an 802.11 medium access control ( MAC ) and physical layer ( PHY ) interface and provides access to the distribution services via the wireless medium for associated clients. LWAPP APs encapsulate all the 802.11 frames in LWAPP frames and sends them to the controller to which it is logically connected. Light Weight Access Point Protocol ( LWAPP ) This is a generic protocol that defines the communication between the Access Points and the Central Controller. Mobile Node ( MN ) A roaming 802.11 wireless device in a wireless network associated with an access point. Mobile Node and client are used interchangeably. Extensible Authentication Protocol ( EAP ) EAP is a universal authentication protocol used in wireless and PPP networks. It is defined by RFC 3748. EAP-Flexible Authentication ( EAP-FAST ) This protocol is used via secure tunneling for 802.1X EAP. PAC PAC (Protected Access Credential) is a meachanism for mutual authentication in EAP-FAST. PEAP The Protected Extensible Authentication Protocol, also known as Protected EAP or simply PEAP, is a protocol that encapsulates EAP within a potentially encrypted and authenticated Transport Layer Security (TLS) tunnel.The purpose was to correct deficiencies in EAP; EAP assumed a protected communication channel, such as that provided by physical security, so facilities for protection of the EAP conversation were not provided. EAP-SIM EAP for GSM Subscriber Identity Module (EAP-SIM) is used for authentication and session key distribution using the Subscriber Identity Module (SIM) from the Global System for Mobile Communications (GSM). RAID Redudant array of independant disks (RAID) combines multiple disk drive components into logical unit for the purposes of data redundancy and performance improvements. Lawful-Interception (LI) Lawful Interception is a feature to send client logging details to a server. REFERENCE [1] Wireless LAN Medium Access Control ( MAC ) and Physical Layer ( PHY ) Specifications. [2] Draft-obara-capwap-lwapp-00.txt, IETF Light Weight Access Point Protocol. [3] IEEE 802.1X - Authentication for Wireless and Wired Connections.

Contact

Cisco Systems, Customer Service Postal: 170 West Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS Email: cs-wnbu-snmp@cisco.com

Imports

FromSymbols
CISCO-LWAPP-DOT11-CLIENT-MIBcldcClientAccessVLAN
CISCO-SMIciscoMgmt
INET-ADDRESS-MIBInetAddress, InetAddressType, InetPortNumber
SNMP-FRAMEWORK-MIBSnmpAdminString
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMICounter32, Integer32, IpAddress, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso
SNMPv2-TCDisplayString, MacAddress, RowStatus, TEXTUAL-CONVENTION, TimeInterval, TruthValue

Imported by

Nothing in this corpus imports this module.

Load order

Every file a consumer needs in order to load this module, dependencies first.

BRIDGE-MIB
CISCO-LWAPP-AP-MIB
CISCO-LWAPP-DOT11-CLIENT-MIB
CISCO-LWAPP-DOT11-MIB
CISCO-LWAPP-MOBILITY-EXT-MIB
CISCO-LWAPP-RF-MIB
CISCO-LWAPP-SYS-MIB
CISCO-LWAPP-TC-MIB
CISCO-LWAPP-WLAN-MIB
CISCO-LWAPP-WLAN-POLICY-MIB
CISCO-QOS-PIB-MIB
CISCO-SMI
CISCO-TC
ENTITY-MIB
IANA-ENTITY-MIB
IANAifType-MIB
IF-MIB
INET-ADDRESS-MIB
P-BRIDGE-MIB
Q-BRIDGE-MIB
RFC1158-MIB
RFC1271-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMPv2-CONF
SNMPv2-MIB
SNMPv2-SMI
SNMPv2-TC
TOKEN-RING-RMON-MIB
UUID-TC-MIB

Objects

NameOIDSyntaxAccessStatus
ciscoLwappSysMIBNotifs
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.0
ciscoLwappSysMIBObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1
clsConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1
clsDot3BridgeEnabled
OBJECT-TYPE
This object specifies whether 803.2 bridging mode is enabled or disabled on the controller. A value of 'true' indicates that, the bridging mode is enabled. A value of 'false' indicates that, the bridging mode is disabled.
1.3.6.1.4.1.9.9.618.1.1.1TruthValueread-writecurrent
clsConfigDownload
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.2
clsDownloadFileType
OBJECT-TYPE
This object specifies the file types that can be downloaded to the controller. The file types for download are: unknown - Unknown file type code - Code file config - Configuration file webAuthCert - Web authentication certificates webAdminCert - Web administrative certificates signatures - Signature file customWebAuth - Custom web authentication tar file vendorDeviceCert - Vendor device certificates vendorCaCert - Vendor certificate authority certificates ipsecDeviceCert - Ipsec device certificates ipsecCaCert - Ipsec certificate authority certificates radiusavplist - Avp's to be sent in radius packets icon - icon files to be used in Hotspot 2.0 apimage - Download ap image for flexexpress naservcacert - NA server certificate authority certificates webhookcacert - Webhook CA Certificate
1.3.6.1.4.1.9.9.618.1.1.2.1INTEGER {unknown(1), code(2), config(3), webAuthCert(4), webAdminCert(5), signatures(6), customWebAuth(7), vendorDeviceCert(8), vendorCaCert(9), ipsecDeviceCert(10), ipsecCaCert(11), radiusavplist(12), icon(13), apimage(14), naservcacert(15), webhookcacert(16)}read-writecurrent
clsDownloadCertificateKey
OBJECT-TYPE
This object specifies the key used to encrypt the EAP certificate, specified by IEEE 802.1X standard, during upload from the controller and for decrypting the file after its downloaded to the controller. This object is relevant only when clsDownloadFileType is 'vendorDeviceCert'. For all other values of clsDownloadFileType object this will return an empty string.
1.3.6.1.4.1.9.9.618.1.1.2.2SnmpAdminString (SIZE(0..255))read-writecurrent
clsConfigUpload
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.3
clsUploadFileType
OBJECT-TYPE
This object specifies the file types that can be uploaded from the controller. The file types for upload are: unknown - Unknown file config - Configuration file errorLog - Error log systemTrace - System trace trapLog - Trap log crashFile - Crash file signatures - Signature file pac - PAC file radioCoreDump - AP's Radio core dump file invalidConfig - Upload the file which contains the invalid configuration commands feeded by the downloaded Config file. debugfile - Debug file. pktCapture - Packet Capture File watchdogCrash - Watchdog Crash Information File panicCrash - Panic Crash Information File. vendorDevCert - EAP ca certificate. vendorCaCert - EAP dev certificate. webAdminCert - Web Admin certificate. webAuthCert - Web Auth certificate. ipsecDeviceCert - Ipsec device certificates ipsecCaCert - Ipsec certificate authority certificates radiusavplist - Avp's to be sent in radius packets. yangBundle - Bundle of yang files.
1.3.6.1.4.1.9.9.618.1.1.3.1INTEGER {unknown(1), config(2), errorLog(3), systemTrace(4), trapLog(5), crashFile(6), signatures(7), pac(8), radioCoreDump(9), invalidConfig(10), debugfile(11), pktCapture(12), watchdogCrash(13), panicCrash(14), vendorDevCert(15), vendorCaCert(16), webAdminCert(17), webAuthCert(18), ipsecDeviceCert(19), ipsecCaCert(20), radiusavplist(21), yangBundle(22)}read-writecurrent
clsUploadPacUsername
OBJECT-TYPE
This object specifies the upload user name for protected access credential (PAC). This object needs to be set before setting clsUploadFileType to 'pac'. For all other values of clsUploadFileType this will return an empty string.
1.3.6.1.4.1.9.9.618.1.1.3.2SnmpAdminString (SIZE(0..63))read-writecurrent
clsUploadPacPassword
OBJECT-TYPE
This object specifies the upload password for protected access credential (PAC). This object needs to be set before setting clsUploadFileType to 'pac'. For all other values of clsUploadFileType this will return an empty string. When read, this object will return '****'.
1.3.6.1.4.1.9.9.618.1.1.3.3SnmpAdminString (SIZE(0..128))read-writecurrent
clsUploadPacValidity
OBJECT-TYPE
This object specifies the upload validity in days for protected access credential (PAC). This object is relevant only when clsUploadFileType is set to 'pac'. For all other values of clsUploadFileType this will return an empty string.
1.3.6.1.4.1.9.9.618.1.1.3.4Unsigned32 (0..65535)read-writecurrent
clsTransferConfigGroup
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.4
clsTransferConfigFileEncryption
OBJECT-TYPE
This object specifies encryption and decryption of configuration file while uploading and downloading. A value of disable(1) indicates that, encryption is disabled. A value of enable(2) indicates that, encryption is enabled. This is applicable only when clsDownloadFileType, clsUploadFileType is set to Config.
1.3.6.1.4.1.9.9.618.1.1.4.1INTEGER {disable(1), enable(2)}read-writecurrent
clsTransferConfigFileEncryptionKey
OBJECT-TYPE
This object specifies the key to be used when encrypting the configuration file while upload from the controller or while decrypting the file after download to the controller. This is applicable only when clsDownloadFileType, clsUploadFileType is set to Config. When read, this object will return '****'.
1.3.6.1.4.1.9.9.618.1.1.4.2SnmpAdminString (SIZE(0..16))read-writecurrent
clsConfigGeneral
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.5
clsTimeZone
OBJECT-TYPE
This object specifies timezone for the controller. Enter the timezone location index. 1. (GMT-12:00) International Date Line West 2. (GMT-11:00) Samoa 3. (GMT-10:00) Hawaii 4. (GMT -9:00) Alaska 5. (GMT -8:00) Pacific Time (US and Canada) 6. (GMT -7:00) Mountain Time (US and Canada) 7. (GMT -6:00) Central Time (US and Canada) 8. (GMT -5:00) Eastern Time (US and Canada) 9. (GMT -4:00) Altantic Time (Canada) 10. (GMT -3:00) Buenos Aires (Agentina) 11. (GMT -2:00) Mid-Atlantic 12. (GMT -1:00) Azores 13. (GMT) London, Lisbon, Dublin, Edinburgh 14. (GMT +1:00) Amsterdam, Berlin, Rome, Vienna 15. (GMT +2:00) Jerusalem 16. (GMT +3:00) Baghdad 17. (GMT +4:00) Muscat, Abu Dhabi 18. (GMT +4:30) Kabul 19. (GMT +5:00) Karachi, Islamabad, Tashkent 20. (GMT +5:30) Colombo, Kolkata, Mumbai, New Delhi 21. (GMT +5:45) Katmandu 22. (GMT +6:00) Almaty, Novosibirsk 23. (GMT +6:30) Rangoon 24. (GMT +7:00) Saigon, Hanoi, Bangkok, Jakatar 25. (GMT +8:00) HongKong, Bejing, Chongquing 26. (GMT +9:00) Tokyo, Osaka, Sapporo 27. (GMT +9:30) Darwin 28. (GMT+10:00) Sydney, Melbourne, Canberra 29. (GMT+11:00) Magadan, Solomon Is., New Caledonia 30. (GMT+12:00) Kamchatka, Marshall Is., Fiji
1.3.6.1.4.1.9.9.618.1.1.5.1Unsigned32read-writecurrent
clsTimeZoneDescription
OBJECT-TYPE
This object represents the timezone description for the controller.
1.3.6.1.4.1.9.9.618.1.1.5.2SnmpAdminStringread-onlycurrent
clsMaxClientsTrapThreshold
OBJECT-TYPE
This object specifies the threshold for number of clients on the controller to trigger a trap. The trap ciscoLwappMaxClientsReached will be triggered once the count of clients on the controller reaches this limit and the clsMaxClientsTrapEnabled is enabled.
1.3.6.1.4.1.9.9.618.1.1.5.3Unsigned32read-writecurrent
clsMaxRFIDTagsTrapThreshold
OBJECT-TYPE
This object specifies the threshold for number of RFID tags on the controller to trigger a trap. The trap ciscoLwappMaxRFIDTagsReached will be triggered once the count of RFID tags on the controller reaches this limit and the clsMaxRFIDTagsTrapEnabled is enabled.
1.3.6.1.4.1.9.9.618.1.1.5.4Unsigned32read-writecurrent
clsConfigNetworkGeneral
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.5.5
clsNetworkRouteConfigTable
OBJECT-TYPE
This table represents of the network route entries of a switch.
1.3.6.1.4.1.9.9.618.1.1.5.5.1not-accessiblecurrent
clsNetworkRouteConfigEntry
OBJECT-TYPE
Each entry in this table represents the network route of a switch.
1.3.6.1.4.1.9.9.618.1.1.5.5.1.1not-accessiblecurrent
clsNetworkRouteIPAddressType
OBJECT-TYPE
This objects represents network route IP address type.
1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.1InetAddressTypenot-accessiblecurrent
clsNetworkRouteIPAddress
OBJECT-TYPE
This objects represents the network route IP address.
1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.2InetAddressnot-accessiblecurrent
clsNetworkRoutePrefixLength
OBJECT-TYPE
This object specifies the prefix length for route Inet address.
1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.3Unsigned32 (0..128)read-createcurrent
clsNetworkRouteGatewayType
OBJECT-TYPE
This object specifies gateway IP type of network route.
1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.4InetAddressTyperead-createcurrent
clsNetworkRouteGateway
OBJECT-TYPE
This object specifies gateway IP of network route.
1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.5InetAddressread-createcurrent
clsNetworkRouteStatus
OBJECT-TYPE
This object specifies status column for this row and used to create and delete specific instances of rows in this table.
1.3.6.1.4.1.9.9.618.1.1.5.5.1.1.6RowStatusread-createcurrent
clsSensorTemperature
OBJECT-TYPE
This object represents current internal temperature of the unit in Centigrade
1.3.6.1.4.1.9.9.618.1.1.5.6SnmpAdminString (SIZE(0..32))read-onlycurrent
clsLiConfigGeneral
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.5.7
clsLiStatus
OBJECT-TYPE
This object specifies whether lawful intercept is enabled for the flexconnect access points connected to the wireless LAN Controller. A value of 'true' indicates that lawful intercept is enabled. A value of 'false' indicates that lawful intercept is disabled. This config is applicable for flexconnect access points.
1.3.6.1.4.1.9.9.618.1.1.5.7.1TruthValueread-writecurrent
clsLiReportingInterval
OBJECT-TYPE
This object specifies the interval at which AP needs to send LI statistical information to the WLC. Interval is in the range of 60 - 600 seconds. This config is applicable for flexconnect access points.
1.3.6.1.4.1.9.9.618.1.1.5.7.2TimeIntervalread-writecurrent
clsLiAddressType
OBJECT-TYPE
This object specifies the IP address type of the syslog server to which the LI statistics will be sent. This config is applicable for flexconnect access points.
1.3.6.1.4.1.9.9.618.1.1.5.7.3InetAddressTyperead-writecurrent
clsLiAddress
OBJECT-TYPE
This object specifies the IP address of the syslog server to which LI statistics needs to be sent. This config is applicable for flexconnect access points.
1.3.6.1.4.1.9.9.618.1.1.5.7.4InetAddressread-writecurrent
clsSyslogIpConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.6
cLSysLogConfigTable
OBJECT-TYPE
This table represents multiple syslog servers to which the the syslog messages will be sent to by the controller.
1.3.6.1.4.1.9.9.618.1.1.6.1not-accessiblecurrent
cLSysLogConfigEntry
OBJECT-TYPE
Each entry in this table provides information about the host to which the syslog messages will be sent to.
1.3.6.1.4.1.9.9.618.1.1.6.1.1not-accessiblecurrent
cLSysLogServerIndex
OBJECT-TYPE
This object represents the index of the host to which syslog messages will be sent.
1.3.6.1.4.1.9.9.618.1.1.6.1.1.1Unsigned32not-accessiblecurrent
cLSysLogAddressType
OBJECT-TYPE
This object represents the IP address type of the host to which syslog messages will be sent. 'DNS' is used when the hostname of the server is configured.
1.3.6.1.4.1.9.9.618.1.1.6.1.1.2InetAddressTyperead-createcurrent
cLSysLogAddress
OBJECT-TYPE
This object specifies the IP address or hostname of the host to which syslog messages will be sent.
1.3.6.1.4.1.9.9.618.1.1.6.1.1.3InetAddressread-createcurrent
cLSysLogHostRowStatus
OBJECT-TYPE
This is the status column for this row and is used to create and delete specific instances of rows in this table.
1.3.6.1.4.1.9.9.618.1.1.6.1.1.4RowStatusread-createcurrent
cLSysArpUnicastEnabled
OBJECT-TYPE
This object specifies whether ARP unicast is enabled or disabled on the controller. A value of 'true' indicates that, the ARP unicast is enabled. A value of 'false' indicates that, the ARP unicast is disabled.
1.3.6.1.4.1.9.9.618.1.1.7TruthValueread-writecurrent
clsTransferConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.8
clsTransferConfigTable
OBJECT-TYPE
This table represent the server details which will be used by the controller to upload/ download files. The conceptual rows are statically populated by the agent during system boot up.
1.3.6.1.4.1.9.9.618.1.1.8.1not-accessiblecurrent
clsTransferConfigEntry
OBJECT-TYPE
Each entry in this table provides information about the server to which the controller will upload/download files represented by clsTransferType and clsTransferMode.
1.3.6.1.4.1.9.9.618.1.1.8.1.1not-accessiblecurrent
clsTransferType
OBJECT-TYPE
This object represents the type of operation mode of the server by the controller. A value of download indicates that, mode of transfer is download A value of upload indicates that, mode of transfer is upload.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.1INTEGER {download(1), upload(2)}not-accessiblecurrent
clsTransferMode
OBJECT-TYPE
This object represents the protocol used by the server and the controller to transfer a file. A value of tftp indicates that, transfer mode is tftp. A value of ftp indicates that, transfer mode is ftp. A value of sftp indicates that, transfer mode is sftp. A value of usb indicates that, transfer mode is usb.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.2INTEGER {tftp(1), ftp(2), sftp(3), usb(4)}not-accessiblecurrent
clsTransferServerAddressType
OBJECT-TYPE
This object specifies the server IP address type to which the controller will transfer the file.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.3InetAddressTyperead-writecurrent
clsTransferServerAddress
OBJECT-TYPE
This object specifies the server IP address to which the controller will transfer the file. It is governed by clsTransferServerAddressType.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.4InetAddressread-writecurrent
clsTransferPath
OBJECT-TYPE
This object specifies the directory path for file transfer. The format depends on the host server. e.g. /tftpboot/code/ - in case of UNIX server c:\tftp\code - in case of DOS/Windows server
1.3.6.1.4.1.9.9.618.1.1.8.1.1.5SnmpAdminString (SIZE(0..64))read-writecurrent
clsTransferFilename
OBJECT-TYPE
This object specifies the file name for the file being transferred from the controller. An example would be file path set to c:\tftp\code\ and file name set to e1r1v1.opr.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.6SnmpAdminString (SIZE(0..64))read-writecurrent
clsTransferFtpUsername
OBJECT-TYPE
This object specifies the FTP username for transferring file on the server. This is valid for FTP/SFTP transfer mode parameters.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.7SnmpAdminString (SIZE(0..31))read-writecurrent
clsTransferFtpPassword
OBJECT-TYPE
This object specifies the FTP password for transferring file on the server. This is valid for SFTP/FTP transfer mode parameters. It returns '****' when queried.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.8SnmpAdminString (SIZE(0..31))read-writecurrent
clsTransferFtpPortNum
OBJECT-TYPE
This object specifies the port number to be used by the FTP protocol while connecting to the server. This is valid only for FTP transfer mode.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.9InetPortNumberread-writecurrent
clsTransferTftpMaxRetries
OBJECT-TYPE
This object specifies maximum number of retries to be allowed for a TFTP message packet before aborting the transfer operation. This is valid only for TFTP transfer mode.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.10Unsigned32 (1..254)read-writecurrent
clsTransferTftpTimeout
OBJECT-TYPE
This object specifies timeout in seconds for a TFTP message packet. This is valid only for TFTP transfer mode.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.11Unsigned32 (1..254)read-writecurrent
clsTransferStart
OBJECT-TYPE
This object specifies whether the file transfer operation is initiated in active or standby. A value of none indicates that, no operation begins. A value of initiate indicates that, transfer of file begins on active. A value of initiatePeer indicates that, file transfer operation begins on standby.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.12INTEGER {none(1), initiate(2), initiatePeer(3)}read-writecurrent
clsTransferStatus
OBJECT-TYPE
This object represents the current status of a file transfer operation. The following are valid only when clsTransferType is 'download' :- bootBreakOff(14), invalidTarFile(15). A value of unknown(1) indicates that, unknown state of transfer. A value of notInitiated(2) indicates that, no transfer operation has been initiated A value of transferStarting(3) indicates that, transfer operation has commenced. A value of errorStarting(4) indicates that, error while starting transfer operation. A value of wrongFileType(5) indicates that, wrong file type specified. A value of updatingConfig(6) indicates that, updating configuration. A value of invalidConfigFile(7) indicates that, invalid config file specified. A value of writingToFlash(8) indicates that, writing to flash A value of failureWritingToFlash(9) indicates that, writing to flash failed. A value of checkingCRC(10) indicates that, checking cyclic redundancy check. A value of failedCRC(11) indicates that, CRC check failed. A value of unknownDirection(12) indicates that, unknown direction of transfer. A value of transferSuccessful(13) indicates that, transfer operation succeeded. A value of transferFailed(14) indicates that, transfer failed. A value of bootBreakOff(15) indicates that, Boot break off. A value of invalidTarFile(16) indicates that, invalid Tar file.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.13INTEGER {unknown(1), notInitiated(2), transferStarting(3), errorStarting(4), wrongFileType(5), updatingConfig(6), invalidConfigFile(7), writingToFlash(8), failureWritingToFlash(9), checkingCRC(10), failedCRC(11), unknownDirection(12), transferSuccessful(13), transferFailed(14), bootBreakOff(15), invalidTarFile(16)}read-onlycurrent
clsTransferStatusString
OBJECT-TYPE
This object represents the current status of a file transfer operation in human readable format.
1.3.6.1.4.1.9.9.618.1.1.8.1.1.14SnmpAdminString (SIZE(0..255))read-onlycurrent
clsStreamingTransferConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.8.2
clsApTransferTable
OBJECT-TYPE
This table represents the information about the 802.11 LWAPP Access Points that have joined to the controller. LWAPP APs exchange configuration messages with the controller and get the required configuration for their 802.11 related operations, after they join the controller.
1.3.6.1.4.1.9.9.618.1.1.8.2.1not-accessiblecurrent
clsApTransferEntry
OBJECT-TYPE
Each entry in this table provides information about one 802.11 LWAPP Access Point that has joined to the controller. Entries are removed when the APs lose their association with the controller due to loss of communication.
1.3.6.1.4.1.9.9.618.1.1.8.2.1.1not-accessiblecurrent
clsApTransferSysMacAddress
OBJECT-TYPE
This object represents the radio MAC address of the AP and uniquely identifies an entry in this table.
1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.1MacAddressnot-accessiblecurrent
clsApPrimaryVers
OBJECT-TYPE
This object represents the primary image version of AP
1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.2SnmpAdminString (SIZE(0..64))read-onlycurrent
clsApBackupVers
OBJECT-TYPE
This object represents the backup image version of AP
1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.3SnmpAdminString (SIZE(0..64))read-onlycurrent
clsApPredStatus
OBJECT-TYPE
This object represents the status of predownload, Initiated/failed/predownloading/backedoff
1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.4SnmpAdminString (SIZE(0..64))read-onlycurrent
clsApPredFailReason
OBJECT-TYPE
This object represents Failure reason for image download.
1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.5SnmpAdminString (SIZE(0..64))read-onlycurrent
clsApPredRetryCount
OBJECT-TYPE
This object represents number of retries by AP to download the image
1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.6Unsigned32 (1..254)read-onlycurrent
clsApPredNextRetryTime
OBJECT-TYPE
This object represents the next retry time of image download by AP.
1.3.6.1.4.1.9.9.618.1.1.8.2.1.1.7SnmpAdminString (SIZE(0..64))read-onlycurrent
clsTransferStreamingMode
OBJECT-TYPE
This object specifies the mode of transfer used by the controller with the server. A value of tftp indicates that, streaming mode is TFTP. A value of http indicates that, streaming mode is http. A value of cco indicates that, streaming mode is cco. A value of https indicates that, streaming mode is https. A value of sftp indicates that, streaming mode is sftp.
1.3.6.1.4.1.9.9.618.1.1.8.2.2INTEGER {tftp(1), http(2), cco(3), https(4), sftp(5)}read-writecurrent
clsTransferStreamingServerAddressType
OBJECT-TYPE
This object specifies the server IP address type from which the controller will transfer the image file.
1.3.6.1.4.1.9.9.618.1.1.8.2.3InetAddressTyperead-writecurrent
clsTransferStreamingServerAddress
OBJECT-TYPE
This object specifies the server IP address to which the controller will transfer the file.
1.3.6.1.4.1.9.9.618.1.1.8.2.4InetAddressread-writecurrent
clsTransferStreamingPath
OBJECT-TYPE
This object specifies the directory path for file transfer. The controller remembers the last file path used.
1.3.6.1.4.1.9.9.618.1.1.8.2.5SnmpAdminString (SIZE(0..64))read-writecurrent
clsStreamingTransferStart
OBJECT-TYPE
This object specifies whether the file transfer operation started or not. A value of initiate(1) indicates that, the transfer operation is started. A value of none(2) indicates that, no operation is started
1.3.6.1.4.1.9.9.618.1.1.8.2.6INTEGER {initiate(1), none(2)}read-writecurrent
clsTransferHttpStreamingUsername
OBJECT-TYPE
This object specifies username of CCO server. Specific to http/cco mode
1.3.6.1.4.1.9.9.618.1.1.8.2.7SnmpAdminString (SIZE(0..64))read-writecurrent
clsTransferHttpStreamingPassword
OBJECT-TYPE
This object specifies password of CCO server. Specific to http/cco mode
1.3.6.1.4.1.9.9.618.1.1.8.2.8SnmpAdminString (SIZE(0..64))read-writecurrent
clsTransferHttpStreamingSuggestedVersion
OBJECT-TYPE
This object represents suggested image version to be downloaded from CCO.Specific to http/cco mode
1.3.6.1.4.1.9.9.618.1.1.8.2.9SnmpAdminString (SIZE(0..64))read-onlycurrent
clsTransferHttpStreamingLatestVersion
OBJECT-TYPE
This object represents latest image version to be downloaded from CCO.Specific to http/cco mode
1.3.6.1.4.1.9.9.618.1.1.8.2.10SnmpAdminString (SIZE(0..64))read-onlycurrent
clsTransferHttpStreamingCcoPoll
OBJECT-TYPE
This object represents recent CCO Polled time
1.3.6.1.4.1.9.9.618.1.1.8.2.11SnmpAdminString (SIZE(0..64))read-onlycurrent
clsTransferStreamingServerPort
OBJECT-TYPE
This object represents streaming server port for https/sftp
1.3.6.1.4.1.9.9.618.1.1.8.2.12Integer32read-writecurrent
clsTransferStreamingUsername
OBJECT-TYPE
This object specifies username of server. Specific to https/sftp mode
1.3.6.1.4.1.9.9.618.1.1.8.2.13SnmpAdminString (SIZE(0..64))read-writecurrent
clsTransferStreamingPassword
OBJECT-TYPE
This object specifies password of server. Specific to https/sftp mode
1.3.6.1.4.1.9.9.618.1.1.8.2.14SnmpAdminString (SIZE(0..64))read-writecurrent
clsTransferStreamingOptimizedJoinEnable
OBJECT-TYPE
This object specified the state of the optimized join feature.
1.3.6.1.4.1.9.9.618.1.1.8.2.15TruthValueread-writecurrent
cLSysBroadcastForwardingEnabled
OBJECT-TYPE
This object specifies whether broadcast forwarding is enabled or disabled on the controller. A value of 'true' indicates that, the broadcast forwarding is enabled. A value of 'false' indicates that, the broadcast forwarding is disabled.
1.3.6.1.4.1.9.9.618.1.1.9TruthValueread-writecurrent
cLSysLagModeEnabled
OBJECT-TYPE
This object specifies whether Link Aggregation(LAG) mode is enabled or disabled on the controller. A value of 'true' indicates that, the LAG mode is enabled. A value of 'false' indicates that, the LAG mode is disabled on the controller.
1.3.6.1.4.1.9.9.618.1.1.10TruthValueread-writecurrent
clsConfigProductBranchVersion
OBJECT-TYPE
This object represents the branch name of the specific controller branch. For Mesh branches, this string has the value M(Mesh). Zero length string is returned if there is no branch name. This string is append to the product version for display purposes. For example, if the mesh product version is 4.1.191.10, a manager application may the version string as 4.1.191.10M (Mesh)
1.3.6.1.4.1.9.9.618.1.1.11SnmpAdminString (SIZE(0..30))read-onlycurrent
clsConfigDhcpProxyEnabled
OBJECT-TYPE
This object specifies whether the DHCP proxy option is enabled or disabled. A value of 'true' indicates that, the proxy option is enabled on the controller. A value of 'false' indicates that, the proxy option is disabled on the controller.
1.3.6.1.4.1.9.9.618.1.1.12TruthValueread-writecurrent
cLSysMulticastIGMP
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.13
cLSysMulticastIGMPSnoopingEnabled
OBJECT-TYPE
This object specifies whether Multicast IGMP Snooping is enabled or disabled on the controller. A value of 'true' indicates that the Multicast IGMP Snooping is enabled. To enable this, agentNetworkMulticastMode/clsConfigMulticastEnabled must not be in disabled state. A value of 'false' indicates that the Multicast IGMP Snooping is disabled on the controller.
1.3.6.1.4.1.9.9.618.1.1.13.1TruthValueread-writecurrent
cLSysMulticastIGMPSnoopingTimeout
OBJECT-TYPE
This object specifies the IGMP timeout, in seconds. To set this value, cLSysMulticastIGMPSnoopingEnabled must be set to true. When the timeout expires, the controller sends a query on all WLANs, causing all clients that are listening to a multicast group to send a packet back to the controller.
1.3.6.1.4.1.9.9.618.1.1.13.2Unsigned32read-writecurrent
cLSysMulticastIGMPQueryInterval
OBJECT-TYPE
This object specifies the IGMP query interval, in seconds. To set this value, cLSysMulticastIGMPSnoopingEnabled must be set to true.
1.3.6.1.4.1.9.9.618.1.1.13.3Unsigned32read-writecurrent
cLSysMulticastLLBridgingStatus
OBJECT-TYPE
This object specifies whether link local is enabled or disabled on the controller. A value of 'true' indicates that the link local is enabled. A value of 'false' indicates that the link local is disabled on the controller.
1.3.6.1.4.1.9.9.618.1.1.13.4TruthValueread-writecurrent
cLSPortModeConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.14
clsPortModeConfigTable
OBJECT-TYPE
This table represents the entries for physical port related parameters.
1.3.6.1.4.1.9.9.618.1.1.14.1not-accessiblecurrent
clsPortModeConfigEntry
OBJECT-TYPE
Each entry contains the switch's physical port, phyical mode related attribues. Each entry exists for available physical interface. Entries cannot be created or deleted by the user.
1.3.6.1.4.1.9.9.618.1.1.14.1.1not-accessiblecurrent
clsPortDot1dBasePort
OBJECT-TYPE
This object represents unique unsigned integer value which identifies the base port number.
1.3.6.1.4.1.9.9.618.1.1.14.1.1.1Unsigned32 (1..65535)not-accessiblecurrent
clsPortModePhysicalMode
OBJECT-TYPE
The object specifies the speed mode of switch port. A value of autoNegotiate indicates that, port senses speed and negotiates with the port at the other end of the link for data transfer operation A value of half10 indicates that, port operates at 10mbps half duplex speed. A value of full10 indicates that, port operates at 10mbps full duplex speed. A value of half100 indicates that, port operates at 100mbps half duplex speed. A value of full100 indicates that, port operates at 100mbps full duplex speed. A value of full1000sx indicates that, port operates at 1000mbps full duplex speed over multi mode fiber. A value of half1000 indicates that, port operates at 1000mbps half duplex speed. A value of full1000 indicates that, port operates at 1000mbps full duplex speed. A value of half10000 indicates that, port operates at 10000mbps half duplex speed. A value of full10000 indicates that, port operates at 10000mbps full duplex speed.
1.3.6.1.4.1.9.9.618.1.1.14.1.1.2INTEGER {autoNegotiate(1), half10(2), full10(3), half100(4), full100(5), full1000sx(6), half1000(7), full1000(8), half10000(9), full10000(10)}read-writecurrent
clsPortModePhysicalStatus
OBJECT-TYPE
This object represents the switch port's current physical speed status. A value of unknown indicates that, the speed of the port is not known A value of autoNegotiate indicates that, port senses speed and negotiates with the port at the other end of the link for data transfer operation A value of half10 indicates that, port operates at 10mbps half duplex speed. A value of full10 indicates that, port operates at 10mbps full duplex speed. A value of half100 indicates that, port operates at 100mbps half duplex speed. A value of full100 indicates that, port operates at 100mbps full duplex speed A value of full1000sx indicates that, port operates at 1000mbps full duplex speed over multi mode fiber. A value of half1000 indicates that, port operates at 1000mbps half duplex speed. A value of full1000 indicates that, port operates at 1000mbps full duplex speed. A value of half2500 indicates that, port operates at 2500mbps half duplex speed. A value of full2500 indicates that, port operates at 2500mbps full duplex speed. A value of half5000 indicates that, port operates at 5000mbps half duplex speed. A value of full5000 indicates that, port operates at 5000mbps full duplex speed. A value of half10000 indicates that, port operates at 10000mbps half duplex speed. A value of full10000 indicates that, port operates at 10000mbps full duplex speed.
1.3.6.1.4.1.9.9.618.1.1.14.1.1.3INTEGER {unknown(1), autonegotiate(2), half10(3), full10(4), half100(5), full100(6), full1000sx(7), half1000(8), full1000(9), half10000(10), full10000(11), half2500(12), full2500(13), half5000(14), full5000(15)}read-onlycurrent
clsPortModeSfpType
OBJECT-TYPE
This object represents the SFP type of the port. When there is no SFP connected to the port, the string is represented with value as Not Present.
1.3.6.1.4.1.9.9.618.1.1.14.1.1.4SnmpAdminStringread-onlycurrent
clsPortUpDownCount
OBJECT-TYPE
This object represents the total number of up/down count of the port. Every time the value of ifOperStatus is changed, this MIB object should be incremented.
1.3.6.1.4.1.9.9.618.1.1.14.1.1.5Counter32read-onlycurrent
clsPortModeMaxSpeed
OBJECT-TYPE
The object specifies the maxspeed mode of MGIG port. A value of full1000 indicates that, port will operate at maximum autonegotiated speed of 1000mbps or less. A value of full2500 indicates that, port will operate at maximum autonegotiated speed of 2500mbps or less. A value of full5000 indicates that, port will operate at maximum autonegotiated speed of 5000mbps or less.
1.3.6.1.4.1.9.9.618.1.1.14.1.1.6INTEGER {autonegotiate(1), full1000(2), full2500(3), full5000(4)}read-writecurrent
clsCoreDump
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.15
clsCoreDumpTransferEnable
OBJECT-TYPE
This object specifies whether the core dump file transfer is enabled or disabled. A value of 'true' indicates that, the core dump file transfer is enabled. A value of 'false' indicates that , the core dump file transfer is disabled
1.3.6.1.4.1.9.9.618.1.1.15.1TruthValueread-writecurrent
clsCoreDumpTransferMode
OBJECT-TYPE
This object specifies the Core Dump Transfer Mode. A value 'unknown' cannot be set. A value of ftp indicates that, mode is ftp. FTP attributes clsCoreDumpServerIpAddress, clsCoreDumpFileName, clsCoreDumpUserName, clsCoreDumpPassword can be set. unknown when the value of clsCoreDumpTransferEnable is disabled.
1.3.6.1.4.1.9.9.618.1.1.15.2INTEGER {unknown(1), ftp(2)}read-writecurrent
clsCoreDumpServerIPAddressType
OBJECT-TYPE
This object specifies the IP address type of the server.
1.3.6.1.4.1.9.9.618.1.1.15.3InetAddressTyperead-writecurrent
clsCoreDumpServerIPAddress
OBJECT-TYPE
This object specifies the IP address of the server where the core-dump will be uploaded. The type of this address is determined by the value of clsCoreDumpServerIpAddressType object.
1.3.6.1.4.1.9.9.618.1.1.15.4InetAddressread-writecurrent
clsCoreDumpFileName
OBJECT-TYPE
This object specifies the filename of the core-dump by which it gets uploaded on the server.
1.3.6.1.4.1.9.9.618.1.1.15.5SnmpAdminStringread-writecurrent
clsCoreDumpUserName
OBJECT-TYPE
This object specifies the login name at the FTP server.
1.3.6.1.4.1.9.9.618.1.1.15.6SnmpAdminStringread-writecurrent
clsCoreDumpPassword
OBJECT-TYPE
This object specifies the login password of the FTP server.
1.3.6.1.4.1.9.9.618.1.1.15.7SnmpAdminStringread-writecurrent
clsConfigMulticastEnabled
OBJECT-TYPE
This object specifies whether global multicast is enabled or disabled. A value of 'true' indicates that the multicast option is enabled on the controller. A value of 'false' indicates that the multicast option is disabled on the controller.
1.3.6.1.4.1.9.9.618.1.1.16TruthValueread-writecurrent
cLSysMulticastMLD
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.17
cLSysMulticastMLDSnoopingEnabled
OBJECT-TYPE
This object specifies whether multicast MLD Snooping is enabled or disabled on the controller. A value of 'true' indicates that the multicast MLD Snooping is enabled. To enable this, agentNetworkMulticastMode/ clsConfigMulticastEnabled must not be in disabled state. A value of 'false' indicates that the multicast MLD Snooping is disabled on the controller.
1.3.6.1.4.1.9.9.618.1.1.17.1TruthValueread-writecurrent
cLSysMulticastMLDSnoopingTimeout
OBJECT-TYPE
This object specifies the MLD timeout, in seconds. To set this value, cLSysMulticastMLDSnoopingEnabled must be set to True. When the timeout expires, the controller sends a query on all WLANs, causing all clients that are listening to a multicast group to send a packet back to the controller.
1.3.6.1.4.1.9.9.618.1.1.17.2Unsigned32read-writecurrent
cLSysMulticastMLDQueryInterval
OBJECT-TYPE
This object specifies the MLD query interval, in seconds. To set this value, cLSysMulticastMLDSnoopingEnabled must be set to true.
1.3.6.1.4.1.9.9.618.1.1.17.3Unsigned32read-writecurrent
clsConfigStats
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.18
clsSysRealtimeStatsTimer
OBJECT-TYPE
This object specifies the realtime stats interval of the system. There are 2 stats modes: realtime and normal. Realtime interval is much less than normal mode.
1.3.6.1.4.1.9.9.618.1.1.18.1Unsigned32 (2..5)read-writecurrent
clsSysNormalStatsTimer
OBJECT-TYPE
This object specifies the normal stats interval of the system. There are 2 stats modes: realtime and normal. Realtime interval is much less than normal mode.
1.3.6.1.4.1.9.9.618.1.1.18.2Unsigned32 (10..180)read-writecurrent
clsSysStatsSamplingInterval
OBJECT-TYPE
This object specifies the sampling interval of the system, which is applied to WLC and APs connected to this WLC. WLC and APs poll specific data every sampling interval.
1.3.6.1.4.1.9.9.618.1.1.18.3Unsigned32read-writecurrent
clsSysStatsAverageInterval
OBJECT-TYPE
This object specifies the average statistics interval of the system, which is applied to WLC and APs connected to this WLC. This interval works as a time window for calculating the average value of the data polled by WLC/AP every sampling interval.
1.3.6.1.4.1.9.9.618.1.1.18.4Unsigned32read-writecurrent
clsAlarmObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.19
clsAlarmHoldTime
OBJECT-TYPE
This object specifies the time in seconds for which an alarm object should be soaked when its on/off state is changed.
1.3.6.1.4.1.9.9.618.1.1.19.1Unsigned32 (0..3600)read-writecurrent
clsAlarmTrapRetransmitInterval
OBJECT-TYPE
This object specifies the trap retransmission interval in seconds. Setting this value to 0 means no retransmission.
1.3.6.1.4.1.9.9.618.1.1.19.2Unsigned32 (0..65535)read-writecurrent
clsSysThresholdConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.20
clsSysControllerCpuUsageThreshold
OBJECT-TYPE
This object specifies the CPU usage threshold on a controller. Setting this value to 0 means no threshold.
1.3.6.1.4.1.9.9.618.1.1.20.1Unsigned32 (0..100)read-writecurrent
clsSysControllerMemoryUsageThreshold
OBJECT-TYPE
This object specifies the memory usage threshold on a controller. Setting this value to 0 means no threshold.
1.3.6.1.4.1.9.9.618.1.1.20.2Unsigned32 (0..100)read-writecurrent
clsSysApCpuUsageThreshold
OBJECT-TYPE
This object specifies the CPU usage threshold on a AP. Setting this value to 0 means no threshold.
1.3.6.1.4.1.9.9.618.1.1.20.3Unsigned32 (0..100)read-writecurrent
clsSysApMemoryUsageThreshold
OBJECT-TYPE
This object specifies the memory usage threshold on a AP. Setting this value to 0 means no threshold.
1.3.6.1.4.1.9.9.618.1.1.20.4Unsigned32 (0..100)read-writecurrent
clsNMHeartBeat
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.21
clsNMHeartBeatEnable
OBJECT-TYPE
This object specifies whether heart beat trap to network manager is enabled or disabled. A value of 'true' indicates that, network manager heart beat feature is enabled. A value of 'false' indicates that, network manager heart beat feature is disabled.
1.3.6.1.4.1.9.9.618.1.1.21.1TruthValueread-writecurrent
clsNMHeartBeatInterval
OBJECT-TYPE
This object specifies the heart beat trap interval in seconds to network manager.
1.3.6.1.4.1.9.9.618.1.1.21.2Unsigned32 (1..65535)read-writecurrent
clsSysLogEnabled
OBJECT-TYPE
This object specifies whether debug log to syslog is enabled or disabled. A value of 'true' indicates that debug log to syslog is enabled on the controller. A value of 'false' indicates that debug log to syslog is disabled on the controller.
1.3.6.1.4.1.9.9.618.1.1.22TruthValueread-writecurrent
clsSysLogLevel
OBJECT-TYPE
This object specifies the debug log level that can be send to syslog on the controller. The level for syslog are: emergencies - system is unusable alerts - action must be taken immediately critical - critical conditions errors - error conditions warnings - warning conditions notifications - normal but signification condition informational - Informational debugging - debug-level messages.
1.3.6.1.4.1.9.9.618.1.1.23INTEGER {emergencies(1), alerts(2), critical(3), errors(4), warnings(5), notifications(6), informational(7), debugging(8)}read-writecurrent
clsConfigApMaxCount
OBJECT-TYPE
This object represents the the max number of AP's supported in WLC.
1.3.6.1.4.1.9.9.618.1.1.24Unsigned32read-onlydeprecated
cLSTrapSwitchConfig
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.25
clsTrapBlacklistTable
OBJECT-TYPE
This table represents the trap blacklist. Traps in black list will be blocked while sending out.
1.3.6.1.4.1.9.9.618.1.1.25.1not-accessiblecurrent
clsTrapBlacklistEntry
OBJECT-TYPE
Each entry in this table provides the name of trap in trap blacklist.
1.3.6.1.4.1.9.9.618.1.1.25.1.1not-accessiblecurrent
clsBlacklistTrapIndex
OBJECT-TYPE
This object represents trap uniquely in blacklist.
1.3.6.1.4.1.9.9.618.1.1.25.1.1.1Unsigned32not-accessiblecurrent
clsTrapNameInBlacklist
OBJECT-TYPE
This object specifies name of trap in trap blacklist.
1.3.6.1.4.1.9.9.618.1.1.25.1.1.2SnmpAdminStringread-createcurrent
clsTrapBlacklistRowStatus
OBJECT-TYPE
This is the status column for this row and used to create and delete specific instances of rows in this table.
1.3.6.1.4.1.9.9.618.1.1.25.1.1.3RowStatusread-createcurrent
clsLinkLocalBridgingEnabled
OBJECT-TYPE
This object specifies whether link local bridging on client packets is enabled or disabled. A value of 'true' indicates that link local bridging on client packets is enabled on the controller. A value of 'false' indicates that link local bridging on client packets is disabled on the controller.
1.3.6.1.4.1.9.9.618.1.1.26TruthValueread-writecurrent
clsNetworkHttpProfCustomPort
OBJECT-TYPE
This object specifies the custom port for http profiling.
1.3.6.1.4.1.9.9.618.1.1.27Unsigned32 (1..65535)read-writecurrent
clsIconCfgTable
OBJECT-TYPE
This table represents the generic icon file configuration in the controller. It has only one argument; the icon file name which shall be used to index the rows in this table.
1.3.6.1.4.1.9.9.618.1.1.28not-accessiblecurrent
clsIconCfgEntry
OBJECT-TYPE
Each entry in this table represents the icon config entry
1.3.6.1.4.1.9.9.618.1.1.28.1not-accessiblecurrent
clsIconCfgFileName
OBJECT-TYPE
This object represents the icon filename
1.3.6.1.4.1.9.9.618.1.1.28.1.1SnmpAdminString (SIZE(1..32))not-accessiblecurrent
clsIconCfgFileType
OBJECT-TYPE
This object specifies the filetype of the icon file
1.3.6.1.4.1.9.9.618.1.1.28.1.2SnmpAdminString (SIZE(1..32))read-createcurrent
clsIconCfgLangCode
OBJECT-TYPE
This object specifies the language code associated with the icon file
1.3.6.1.4.1.9.9.618.1.1.28.1.3SnmpAdminString (SIZE(2..3))read-createcurrent
clsIconCfgWidth
OBJECT-TYPE
This object specifies the width of the icon file
1.3.6.1.4.1.9.9.618.1.1.28.1.4Unsigned32 (0..65535)read-createcurrent
clsIconCfgHeight
OBJECT-TYPE
This object specifies the height of the icon file
1.3.6.1.4.1.9.9.618.1.1.28.1.5Unsigned32 (0..65535)read-createcurrent
clsIconCfgRowStatus
OBJECT-TYPE
This object specifies status column for this row and used to create and delete specific instances of rows in this table.
1.3.6.1.4.1.9.9.618.1.1.28.1.6RowStatusread-createcurrent
clsNetworkHttpProxyPort
OBJECT-TYPE
This object specifies the custom port for http proxy
1.3.6.1.4.1.9.9.618.1.1.29Unsigned32 (1..65535)read-writecurrent
clsNetworkHttpProxyIpType
OBJECT-TYPE
This object specifies the http proxy IP address type
1.3.6.1.4.1.9.9.618.1.1.30InetAddressTyperead-writecurrent
clsNetworkHttpProxyIp
OBJECT-TYPE
This Object specifies the IP address of the http proxy
1.3.6.1.4.1.9.9.618.1.1.31InetAddressread-writecurrent
clsNetworkDnsServerIpType
OBJECT-TYPE
This object specifies the DNS server IP address type
1.3.6.1.4.1.9.9.618.1.1.32InetAddressTyperead-writecurrent
clsNetworkDnsServerIp
OBJECT-TYPE
This Object specifies the IP address of the DNS server
1.3.6.1.4.1.9.9.618.1.1.33InetAddressread-writecurrent
clsConfigCalea
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.1.34
clsConfigCaleaEnabled
OBJECT-TYPE
This object specifies whether CALEA lawful Intercept feature enabled or disabled. A value of 'true' indicates that, CALEA lawful Intercept feature enabled. A value of 'false'indicates that, CALEA lawful Intercept feature disabled.
1.3.6.1.4.1.9.9.618.1.1.34.1TruthValueread-writecurrent
clsConfigCaleaServerIp
OBJECT-TYPE
This object specifies the address of the CALEA lawful intercept server
1.3.6.1.4.1.9.9.618.1.1.34.2IpAddressread-writedeprecated
clsConfigCaleaPort
OBJECT-TYPE
This object specifies about port number of CALEA lawful intercept server
1.3.6.1.4.1.9.9.618.1.1.34.3InetPortNumberread-writecurrent
clsConfigCaleaAccountingInterval
OBJECT-TYPE
This object specifies the accounting interval of CALEA lawful intercept.
1.3.6.1.4.1.9.9.618.1.1.34.4Unsigned32 (1..1440)read-writecurrent
clsConfigCaleaVenue
OBJECT-TYPE
This object specifies the CALEA Venue description
1.3.6.1.4.1.9.9.618.1.1.34.5SnmpAdminString (SIZE(1..64))read-writecurrent
clsConfigCaleaServerIpType
OBJECT-TYPE
This Object specifies the address type of the CALEA lawful intercept server
1.3.6.1.4.1.9.9.618.1.1.34.6InetAddressTyperead-writecurrent
clsConfigCaleaServerIpAddr
OBJECT-TYPE
This Object specifies the IPv4 address of the CALEA lawful intercept server
1.3.6.1.4.1.9.9.618.1.1.34.7IpAddressread-writecurrent
clSysLogIPSecStatus
OBJECT-TYPE
This object specifies Syslog over IPSEC Status A value of 'true' indicates that, syslog over ipsec is enabled. A value of 'false' indicates that syslog over ipsec is disabled.
1.3.6.1.4.1.9.9.618.1.1.35TruthValueread-writecurrent
clSysLogIPSecProfName
OBJECT-TYPE
This object specifies IPsec profile to be used for syslog over IPSec.
1.3.6.1.4.1.9.9.618.1.1.36SnmpAdminString (SIZE(1..31))read-writecurrent
clsConfigArpUnicastEnabled
OBJECT-TYPE
This object specifies whether arp is forwarded in unicast format or the default mode of Multicast. A value of 'true' indicates that, the arp packets for passive client will be unicasted. A value of 'false' indicates that, the arp-packets will be sent based on the config of multicast mode multicast/unicast.
1.3.6.1.4.1.9.9.618.1.1.37TruthValueread-writecurrent
clsWGBForcedL2RoamEnabled
OBJECT-TYPE
This object specifies whether forced L2 Roaming is enabled or disable for WGB clients. A value of 'true' indicates that, forced L2 Roaming is enabled for WGB clients. A value of 'false' indicates that, forced L2 Roaming is disabled for WGB clients.
1.3.6.1.4.1.9.9.618.1.1.38TruthValueread-writecurrent
clsUSBMode
OBJECT-TYPE
This object specifies whether USB is enabled or disabled. A value of 'true' indicates that, USB is enabled. A value of 'false' indicates that, USB is disabled.
1.3.6.1.4.1.9.9.618.1.1.40TruthValueread-writecurrent
clsCrashSystem
OBJECT-TYPE
This object specifies whether to reset the switch with a crash or not. A value of 'true' indicates that, the switch would crash. A value of 'false'indicates that, not crashed.
1.3.6.1.4.1.9.9.618.1.1.99TruthValueread-writecurrent
clsStatus
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.2
cLSysLagModeInTransition
OBJECT-TYPE
This object represents whether the LAG mode is in transition or not. A value of 'true' indicates that, the LAG mode is in transition and the controller has to be rebooted to take effect. A value of 'false' indicates that, the LAG mode is not in transition.
1.3.6.1.4.1.9.9.618.1.2.1TruthValueread-onlycurrent
clsRAIDStatusTable
OBJECT-TYPE
This table represents the RAID and rebuild status.
1.3.6.1.4.1.9.9.618.1.2.2not-accessiblecurrent
clsRAIDStatusEntry
OBJECT-TYPE
Each entry in this table provides RAID drive status.
1.3.6.1.4.1.9.9.618.1.2.2.1not-accessiblecurrent
clsRAIDDriveNumber
OBJECT-TYPE
This object indicates drive number in the system.
1.3.6.1.4.1.9.9.618.1.2.2.1.1Unsigned32not-accessiblecurrent
clsRAIDStatus
OBJECT-TYPE
This object represents the status of the drive. A value of good indicates that, hard disk in RAID volume is good. A value of bad indicates that, hard disk in RAID volume is bad. A value of badstartrebuild indicates that, hard disk in RAID volume is bad and rebuild is triggered. A value of rebuilding indicates that, hard disk in RAID volume is rebuilding.
1.3.6.1.4.1.9.9.618.1.2.2.1.2INTEGER {good(1), bad(2), badstartrebuild(3), rebuilding(4)}read-onlycurrent
clsRAIDRebuildPercentage
OBJECT-TYPE
This object represents the rebuild percentage of drive. This object is applicable only when RAID status is rebuilding.
1.3.6.1.4.1.9.9.618.1.2.2.1.3Unsigned32read-onlycurrent
clsSysPingTestTable
OBJECT-TYPE
This table represents the test ping entries
1.3.6.1.4.1.9.9.618.1.2.3not-accessiblecurrent
clsSysPingTestEntry
OBJECT-TYPE
Each Entry (conceptual row) in the clsSysPingTest Table represents a ping test id.
1.3.6.1.4.1.9.9.618.1.2.3.1not-accessiblecurrent
clsSysPingTestId
OBJECT-TYPE
This object represents the index of pingtest ID
1.3.6.1.4.1.9.9.618.1.2.3.1.1Integer32not-accessiblecurrent
clsSysPingTestIPAddressType
OBJECT-TYPE
This object specifies the IP address type
1.3.6.1.4.1.9.9.618.1.2.3.1.2InetAddressTyperead-createcurrent
clsSysPingTestIPAddress
OBJECT-TYPE
This object specifies the IP address of the device to which ping test to perform
1.3.6.1.4.1.9.9.618.1.2.3.1.3InetAddressread-createcurrent
clsSysPingTestSendCount
OBJECT-TYPE
This object specifies the number of bytes sent
1.3.6.1.4.1.9.9.618.1.2.3.1.4Integer32 (1..100)read-createcurrent
clsSysPingTestReceivedCount
OBJECT-TYPE
This object represents the number of bytes received.
1.3.6.1.4.1.9.9.618.1.2.3.1.5Integer32read-onlycurrent
clsSysPingTestStatus
OBJECT-TYPE
This object represents status of the ping test. A value of inprogress indicates that, ping test in progress. A value of complete indicates that, ping test is complete.
1.3.6.1.4.1.9.9.618.1.2.3.1.6INTEGER {inprogress(1), complete(2)}read-onlycurrent
clsSysPingTestMaxTimeInterval
OBJECT-TYPE
This object represents maximum time interval in msec.
1.3.6.1.4.1.9.9.618.1.2.3.1.7Unsigned32read-onlycurrent
clsSysPingTestMinTimeInterval
OBJECT-TYPE
This object represents minimum time interval in msec.
1.3.6.1.4.1.9.9.618.1.2.3.1.8Unsigned32read-onlycurrent
clsSysPingTestAvgTimeInterval
OBJECT-TYPE
This object represents average time interval in msec.
1.3.6.1.4.1.9.9.618.1.2.3.1.9Unsigned32read-onlycurrent
clsSysPingTestRowStatus
OBJECT-TYPE
This is the status column for this row and used to create and delete specific instances of rows in this table.
1.3.6.1.4.1.9.9.618.1.2.3.1.10RowStatusread-createcurrent
clsImageInfo
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.3
clsEmergencyImageVersion
OBJECT-TYPE
This object represents Cisco recommends installing Cisco Unified Wireless Network Controller Boot Software , (*_ER.aes , where star denotes the version of the controller image ) on all controller platforms. If this ER.aes is not installed, the controller would not be able to show the Emergency Image Version correctly(or Field Recovery Image Version), and would be shown as 'N/A'. The ER.aes files are independent from the controller software files. Any controller software file can be run with any ER.aes file. However, installing the latest boot software file (*_ER.aes , where star denotes the controller version) ensures that the boot software modifications in all of the previous and current boot software ER.aes files are installed.
1.3.6.1.4.1.9.9.618.1.3.1SnmpAdminStringread-onlycurrent
clsCpuInfo
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.4
clsAllCpuUsage
OBJECT-TYPE
This object represents the CPU usage string.
1.3.6.1.4.1.9.9.618.1.4.1SnmpAdminStringread-onlycurrent
clsSecurityGroup
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.5
clsSecStrongPwdCaseCheck
OBJECT-TYPE
This object specifies the whether password case check is enabled or disabled. A value of 'true' indicates that, the new password must contain characters from at least three of the following classes : lowercase letters, uppercase letters, digits and special characters. A value of 'false' indicates that, no checks for password.
1.3.6.1.4.1.9.9.618.1.5.1TruthValueread-writecurrent
clsSecStrongPwdConsecutiveCheck
OBJECT-TYPE
This object specifies whether the password consecutive check is enabled or disabled. A value of 'true' indicates that, the password provided should not have a character repeated more than thrice consecutively. A value of 'false' indicates that, character repeatation check disabled
1.3.6.1.4.1.9.9.618.1.5.2TruthValueread-writecurrent
clsSecStrongPwdDefaultCheck
OBJECT-TYPE
This object specifies whether default check for the passwords is enabled or disabled. A value of 'true' indicates that, the new password must not be 'cisco', 'ocsic', 'admin', 'nimda' or any variant obtained by changing the capitalization of letters therein, or by substituting '1' '|' or '!' for i, and/or substituting '0' for 'o', and/or substituting '$' for 's'. A value of 'false' indicates that, default check disabled for the password.
1.3.6.1.4.1.9.9.618.1.5.3TruthValueread-writecurrent
clsSecStrongPwdAsUserNameCheck
OBJECT-TYPE
This object specifies whether username check for the password is enabled or disabled. A value of 'true' indicates that, the new password must not be same as the associated username or the reversed username. A value of 'false' indicates that, check for user name in the password is disabled
1.3.6.1.4.1.9.9.618.1.5.4TruthValueread-writecurrent
clsSecStrongPwdPositionCheck
OBJECT-TYPE
This object specifies whether position check for the passwords is enabled or disabled. A value of 'true' indicates that, position check for the password is enabled. A value of 'false' indicates that, position check for the password is disabled.
1.3.6.1.4.1.9.9.618.1.5.5TruthValueread-writecurrent
clsSecStrongPwdDigitCheck
OBJECT-TYPE
This object specifies whether digit check for the passwords is enabled or disabled. A value of 'true' indicates that, digit check for the passwords is enabled. A value of 'false' indicates that, digit check for the passwords is disabled.
1.3.6.1.4.1.9.9.618.1.5.6TruthValueread-writecurrent
clsSecStrongPwdMinLength
OBJECT-TYPE
This object specifies the minimum password length for the passwords configured in controller.
1.3.6.1.4.1.9.9.618.1.5.7Unsigned32read-writecurrent
clsSecStrongPwdMinUpperCase
OBJECT-TYPE
This object specifies the minimum number of upper case characters for the passwords configured in controller.
1.3.6.1.4.1.9.9.618.1.5.8Unsigned32read-writecurrent
clsSecStrongPwdMinLowerCase
OBJECT-TYPE
This object specifies the minimum number of upper case characters for the passwords configured in controller.
1.3.6.1.4.1.9.9.618.1.5.9Unsigned32read-writecurrent
clsSecStrongPwdMinDigits
OBJECT-TYPE
This object specifies the minimum number of digits for the passwords configured in controller.
1.3.6.1.4.1.9.9.618.1.5.10Unsigned32read-writecurrent
clsSecStrongPwdMinSpecialChar
OBJECT-TYPE
This object specifies the minimum special characters for the passwords configured in controller.
1.3.6.1.4.1.9.9.618.1.5.11Unsigned32read-writecurrent
clsSecWlanCCEnable
OBJECT-TYPE
This object represents whether WLAN common criteria is enabled or disabled. A value of 'true' indicates that, WLAN common criteria is enabled. A value of 'false' indicates that, WLAN common criteria is disabled.
1.3.6.1.4.1.9.9.618.1.5.12TruthValueread-onlycurrent
clsSecUcaplEnable
OBJECT-TYPE
This object represents whether UCAPL is enabled or disabled. A value of 'true' indicates that, UCAPL is enabled. A value of 'false' indicates that, UCAPL is disabled.
1.3.6.1.4.1.9.9.618.1.5.13TruthValueread-onlycurrent
clsSecMgmtUsrLockoutEnable
OBJECT-TYPE
This object specifies whether lockout for the management user is enabled or disabled. A value of 'true'indicates that, lockout for the management user is enabled. A value of 'false' indicates that, lockout for the management user is disabled.
1.3.6.1.4.1.9.9.618.1.5.14TruthValueread-writecurrent
clsSecMgmtUsrLockoutTime
OBJECT-TYPE
This object specifies the lockout time for the management user configured in controller.
1.3.6.1.4.1.9.9.618.1.5.15Unsigned32read-writecurrent
clsSecMgmtUsrLockoutAttempts
OBJECT-TYPE
This object specifies the lockout attempts for the management user configured in controller.
1.3.6.1.4.1.9.9.618.1.5.16Unsigned32read-writecurrent
clsSecSnmpv3UsrLockoutEnable
OBJECT-TYPE
This object specifies whether the lockout for the SNMP version3 user is enabled or disabled. A value of 'true' indicates that, lockout for the SNMPV3 user is enabled. A value of 'false' indicates that, lockout for the SNMPV3 user is disabled.
1.3.6.1.4.1.9.9.618.1.5.17TruthValueread-writecurrent
clsSecSnmpv3UsrLockoutTime
OBJECT-TYPE
This object specifies the lockout time for the SNMP v3 user configured in controller.
1.3.6.1.4.1.9.9.618.1.5.18Unsigned32read-writecurrent
clsSecSnmpv3UsrLockoutAttempts
OBJECT-TYPE
This object specifies the lockout attempts for the SNMP v3 user configured in controller.
1.3.6.1.4.1.9.9.618.1.5.19Unsigned32read-writecurrent
clsSecMgmtUsrLockoutLifetime
OBJECT-TYPE
This object specifies the lockout life time for the management user configured in controller.
1.3.6.1.4.1.9.9.618.1.5.20Unsigned32 (0..180)read-writecurrent
clsSecSnmpv3UsrLockoutLifetime
OBJECT-TYPE
This object specifies the lockout life time for the SNMPV3 user configured in controller.
1.3.6.1.4.1.9.9.618.1.5.21Unsigned32 (0..180)read-writecurrent
ciscoLwappSysMIBNotifObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.6
clsSecStrongPwdManagementUser
OBJECT-TYPE
This object represents the management user who enabled or disabled the strong password checks.
1.3.6.1.4.1.9.9.618.1.6.1SnmpAdminString (SIZE(1..24))read-onlycurrent
clsSecStrongPwdCheckType
OBJECT-TYPE
This object represents the type of the check that was enabled or disabled by the management user. A value of 'caseCheck' indicates that, the caseCheck was enabled or disabled by the management user. A value of 'consecutiveCheck' indicates that, the consecutiveCheck was enabled or disabled by the management user. A value of 'defaultCheck' indicates that, the defaultCheck was enabled or disabled by the management user. A value of 'usernameCheck' indicates that, the usernameCheck was enabled or disabled by the management user. A value of 'allChecks' indicates that, all checks were enabled by the management user.
1.3.6.1.4.1.9.9.618.1.6.2INTEGER {caseCheck(1), consecutiveCheck(2), defaultCheck(3), usernameCheck(4), allChecks(5)}read-onlycurrent
clsSecStrongPwdCheckOption
OBJECT-TYPE
This object represents whether the strong password check was enabled/disabled.
1.3.6.1.4.1.9.9.618.1.6.3TruthValueread-onlycurrent
clsSysAlarmSet
OBJECT-TYPE
This object represents whether this system alarm is raise or clear. A value of 'true' indicates that, this event is enabled. A value of 'false' indicates that, this even is disabled.
1.3.6.1.4.1.9.9.618.1.6.4TruthValueaccessible-for-notifycurrent
clsSysMaxThresholdReachedClear
OBJECT-TYPE
This object represents whether this event is raise or clear. A value of 'true' indicates that, this event is cleared A value of 'false' indicates that, this event is raised.
1.3.6.1.4.1.9.9.618.1.6.5TruthValueaccessible-for-notifycurrent
clsTransferCfgAnalyzeResult
OBJECT-TYPE
This object represents the config file analyze result. A value of unknown indicates that, unknown error. A value of keyMismatch indicates that, the encrypt key mismatch. A value of fileMissing indicates that, the config file missing. A value of contentMismatch indicates that, the file is not intended for this product.
1.3.6.1.4.1.9.9.618.1.6.6INTEGER {unknown(1), keyMismatch(2), fileMissing(3), contentMismatch(4)}accessible-for-notifycurrent
clsWlcSwVersionBeforeUpgrade
OBJECT-TYPE
This object represents the wlc software version info before upgrading fail.
1.3.6.1.4.1.9.9.618.1.6.7SnmpAdminStringaccessible-for-notifycurrent
clsWlcSwVersionAfterUpgrade
OBJECT-TYPE
This object represents the wlc software version info after upgrading fail.
1.3.6.1.4.1.9.9.618.1.6.8SnmpAdminStringaccessible-for-notifycurrent
clsWlcUpgradeFailReason
OBJECT-TYPE
This object represents the wlc upgrade fail reason. A value of unknownReason indicates that, reason is unknown. A value of fileTypeMismatch indicates that, mismatch in the file extension. please check whether the extension is .aes. A value of fileCheckFail indicates that, file check fail, please check whether the image is correct. A value of fileBackupToFlashFail indicates that, flash backup fail, please check whether the flash space is enough.
1.3.6.1.4.1.9.9.618.1.6.9INTEGER {unknownReason(1), fileTypeMismatch(2), fileCheckFail(3), fileBackupToFlashFail(4)}accessible-for-notifycurrent
clsPortNumber
OBJECT-TYPE
This object represents port number of MGIG port.
1.3.6.1.4.1.9.9.618.1.6.10InetPortNumberread-onlycurrent
clsPortSpeed
OBJECT-TYPE
This object represents port speed (Mbps) of MGIG Port.
1.3.6.1.4.1.9.9.618.1.6.11Unsigned32read-onlycurrent
clsPortSlot
OBJECT-TYPE
This object represents slot number where MGIG port is present.
1.3.6.1.4.1.9.9.618.1.6.12Unsigned32read-onlycurrent
ciscoLwappSysMIBNotifControlObjects
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.7
clsSecStrongPwdCheckTrapEnabled
OBJECT-TYPE
This object specifies whether the ciscoLwappStrongPwdCheck notification would be generated. A value of 'true' indicates that, the agent generates ciscoLwappStrongPwdCheck notification. A value of 'false' indicates that, the agent doesn't generates ciscoLwappStrongPwdCheck notification.
1.3.6.1.4.1.9.9.618.1.7.1TruthValueread-writecurrent
clsMaxClientsTrapEnabled
OBJECT-TYPE
This object specifies whether the ciscoLwappMaxClientsReached notification would be generated. A value of 'true' indicates that, the agent generates ciscoLwappMaxClientsReached notification. A value of 'false' indicates that, the agent doesn't generates ciscoLwappMaxClientsReached notification.
1.3.6.1.4.1.9.9.618.1.7.2TruthValueread-writecurrent
clsMaxRFIDTagsTrapEnabled
OBJECT-TYPE
This object specifies whether the ciscoLwappMaxRFIDTagsReached notification would be generated. A value of 'true' indicates that, the agent generates ciscoLwappMaxRFIDTagsReached notification. A value of 'false' indicates that, the agent doesn't generates ciscoLwappMaxRFIDTagsReached notification.
1.3.6.1.4.1.9.9.618.1.7.3TruthValueread-writecurrent
clsNacAlertTrapEnabled
OBJECT-TYPE
This object specifies whether the Nac alert association/disassociation notification would be generated. A value of 'true' indicates that, the agent generates nac alert notification. A value of 'false' indicates that, the agent doesn't generates nac alert notification.
1.3.6.1.4.1.9.9.618.1.7.4TruthValueread-writecurrent
clsMfpTrapEnabled
OBJECT-TYPE
This object specifies whether the mfp trap notification would be generated. A value of 'true' indicates that, the agent generates mfp notification. A value of 'false' indicates that, the agent doesn't generates mfp notification.
1.3.6.1.4.1.9.9.618.1.7.5TruthValueread-writecurrent
clsSysInfo
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.8
clsSysFlashSize
OBJECT-TYPE
This object represents the total flash memory size in Kbytes.
1.3.6.1.4.1.9.9.618.1.8.1Unsigned32read-onlycurrent
clsSysMemoryType
OBJECT-TYPE
This object represents the system memory type.
1.3.6.1.4.1.9.9.618.1.8.2SnmpAdminStringread-onlycurrent
clsSysMaxClients
OBJECT-TYPE
This object represents max associated clients supported per WLC
1.3.6.1.4.1.9.9.618.1.8.3Unsigned32read-onlycurrent
clsSysApConnectCount
OBJECT-TYPE
This object represents the count of AP's that are connected with WLC
1.3.6.1.4.1.9.9.618.1.8.4Unsigned32read-onlycurrent
clsSysNetId
OBJECT-TYPE
This object specifies the SysNetId which is the numeric string to identify the system information like SysName
1.3.6.1.4.1.9.9.618.1.8.5SnmpAdminString (SIZE(0..32))read-writecurrent
clsSysCurrentMemoryUsage
OBJECT-TYPE
This object represents the current percent usage of system memory. This MIB object should be updated every clsSysStatsSamplingInterval.
1.3.6.1.4.1.9.9.618.1.8.6Unsigned32read-onlycurrent
clsSysAverageMemoryUsage
OBJECT-TYPE
This object represents the average percent usage of system memory. The memory average usage should be the average of memory-Usage during the time window specified by clsSysStatsAverageInterval.
1.3.6.1.4.1.9.9.618.1.8.7Unsigned32read-onlycurrent
clsSysCurrentCpuUsage
OBJECT-TYPE
This object represents the current percent usage of all CPUs. This MIB should be updated every clsSysStatsSamplingInterval.
1.3.6.1.4.1.9.9.618.1.8.8Unsigned32read-onlycurrent
clsSysAverageCpuUsage
OBJECT-TYPE
This object represents the average percent CPU usage. The average CPU usage should be the average of CPU-Usage during the time window specified by clsSysStatsAverageInterval.
1.3.6.1.4.1.9.9.618.1.8.9Unsigned32read-onlycurrent
clsSysCpuType
OBJECT-TYPE
This object represents the cpu type.
1.3.6.1.4.1.9.9.618.1.8.10SnmpAdminStringread-onlycurrent
clsMaxRFIDTagsCount
OBJECT-TYPE
This object represents the maximum RFID tags present on the controller.
1.3.6.1.4.1.9.9.618.1.8.11Unsigned32read-onlycurrent
clsMaxClientsCount
OBJECT-TYPE
This object represents the maximum clients present on the controller.
1.3.6.1.4.1.9.9.618.1.8.12Unsigned32read-onlycurrent
clsApAssocFailedCount
OBJECT-TYPE
This object represents the count when Access Point failed to associate with the controller.
1.3.6.1.4.1.9.9.618.1.8.13Counter32read-onlycurrent
clsCurrentPortalClientCount
OBJECT-TYPE
This object represents the current portal clients present on the controller.
1.3.6.1.4.1.9.9.618.1.8.14Unsigned32read-onlycurrent
clsCurrentOnlineUsersCount
OBJECT-TYPE
This object represents the current all online clients present on the controller.
1.3.6.1.4.1.9.9.618.1.8.15Unsigned32read-onlycurrent
clsSysAbnormalOfflineCount
OBJECT-TYPE
This object represents the abnormal offline count for the wlc.
1.3.6.1.4.1.9.9.618.1.8.16Unsigned32read-onlycurrent
clsSysFlashType
OBJECT-TYPE
This object represents the system Flash type.
1.3.6.1.4.1.9.9.618.1.8.17SnmpAdminStringread-onlycurrent
clsSysOpenUsersCount
OBJECT-TYPE
This object represents the current all online open authentication clients present on the controller.
1.3.6.1.4.1.9.9.618.1.8.18Unsigned32read-onlycurrent
clsSysWepPskUsersCount
OBJECT-TYPE
This object represents the current all online wep/psk authentication clients present on the controller.
1.3.6.1.4.1.9.9.618.1.8.19Unsigned32read-onlycurrent
clsSysPeapSimUsersCount
OBJECT-TYPE
This object represents the current all online peap/sim authentication clients present on the controller.
1.3.6.1.4.1.9.9.618.1.8.20Unsigned32read-onlycurrent
clsSysPeapSimReqCount
OBJECT-TYPE
This object represents the PEAP/SIM request on the controller.
1.3.6.1.4.1.9.9.618.1.8.21Counter32read-onlycurrent
clsSysPeapSimReqSuccessCount
OBJECT-TYPE
This object represents the successful PEAP/SIM request on the controller.
1.3.6.1.4.1.9.9.618.1.8.22Counter32read-onlycurrent
clsSysPeapSimReqFailureCount
OBJECT-TYPE
This object represents the failed PEAP/SIM request on the controller.
1.3.6.1.4.1.9.9.618.1.8.23Counter32read-onlycurrent
clsSysNasId
OBJECT-TYPE
This object specifies the SysNasId. NasId is used to support Roaming, location-based service.
1.3.6.1.4.1.9.9.618.1.8.24SnmpAdminString (SIZE(1..31))read-writecurrent
clsSysCoChannelTrapRssiThreshold
OBJECT-TYPE
This object specifies the minimum value of RSSI considered for the trap of Co-Channel AP.
1.3.6.1.4.1.9.9.618.1.8.25Integer32read-writecurrent
clsSysAdjChannelTrapRssiThreshold
OBJECT-TYPE
This object specifies the minimum value of RSSI considered for the trap of Adj channel AP
1.3.6.1.4.1.9.9.618.1.8.26Integer32read-writecurrent
clsSysClientTrapRssiThreshold
OBJECT-TYPE
This object specifies the minimum value of RSSI considered for the trap of client.
1.3.6.1.4.1.9.9.618.1.8.27Integer32read-writecurrent
clsSysCmxActiveConnections
OBJECT-TYPE
This object represents the count of active connections present on the controller.
1.3.6.1.4.1.9.9.618.1.8.28Unsigned32read-onlycurrent
clsLyncInfo
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.1.9
clsLyncState
OBJECT-TYPE
This object specifies whether Lync is enabled on system. A value of 'true' indicates that, Lync state is enabled. A value of 'false' indicates that, Lync state is disabled.
1.3.6.1.4.1.9.9.618.1.9.1TruthValueread-writecurrent
clsLyncPort
OBJECT-TYPE
This object specifies about port number of Lync Service.
1.3.6.1.4.1.9.9.618.1.9.2InetPortNumberread-writecurrent
clsLyncProtocol
OBJECT-TYPE
This object specifies about protocol of Lync Service. A value of http indicates that, lync protocol is http. A value of secure http indicates that, lync protocol is secure http.
1.3.6.1.4.1.9.9.618.1.9.3INTEGER {http(1), securehttp(2)}read-writecurrent
ciscoLwappSysMIBConform
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.2
ciscoLwappSysMIBCompliances
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.2.1
ciscoLwappSysMIBGroups
OBJECT-IDENTITY
1.3.6.1.4.1.9.9.618.2.2

Notifications

NameOIDStatus
ciscoLwappSysInvalidXmlConfig
NOTIFICATION-TYPE
This notification will be sent whenever invalid configuration is detected by XML.
1.3.6.1.4.1.9.9.618.0.1current
ciscoLwappNoVlanConfigured
NOTIFICATION-TYPE
This notification will be sent whenever wired client tries to associate without interface for specified VLAN. cldcClientAccessVLAN represents the access VLAN of the client. cldcClientMacAddress represents the MAC address of the client.
1.3.6.1.4.1.9.9.618.0.2current
ciscoLwappStrongPwdCheckNotif
NOTIFICATION-TYPE
This notification will be sent whenever the management user enables/disables the strong password rules. clsSecStrongPwdManagementUser represents the management user configuring the strong password security checks. clsSecStrongPwdCheckType represents the type of check that has been enabled or disabled. clsSecStrongPwdCheckOption represents the option chosen by the user.
1.3.6.1.4.1.9.9.618.0.3current
ciscoLwappSysCpuUsageHigh
NOTIFICATION-TYPE
This notification will be sent whenever WLC detects its CPU usage is higher than the threshold configured in clsSysControllerCpuUsageThreshold, this notification is generated with clsSysAlarmSet set to true. When its CPU usage falls below the threshold lately, this notification is generated with clsSysAlarmSet set to false.
1.3.6.1.4.1.9.9.618.0.4current
ciscoLwappSysMemoryUsageHigh
NOTIFICATION-TYPE
This notification will be sent whenever WLC detects its memory usage is higher than the threshold configured in clsSysControllerMemoryUsageThreshold, this notification is generated with clsSysAlarmSet set to true. When its memory usage falls below the threshold lately, this notification is generated with clsSysAlarmSet set to false.
1.3.6.1.4.1.9.9.618.0.5current
ciscoLwappMaxRFIDTagsReached
NOTIFICATION-TYPE
This notification is generated when the number of RFID tags on the controller exceeds the limit defined by clsMaxRFIDTagsTrapThreshold.
1.3.6.1.4.1.9.9.618.0.6current
ciscoLwappMaxClientsReached
NOTIFICATION-TYPE
This notification is generated when the number of clients on the controller exceeds the limit defined by clsMaxClientsTrapThreshold.
1.3.6.1.4.1.9.9.618.0.7current
ciscoLwappNMHeartBeat
NOTIFICATION-TYPE
This notification will be sent when Network Manager Heart Beat Enable.
1.3.6.1.4.1.9.9.618.0.8current
ciscoLwappCfgFileAnalyzeFail
NOTIFICATION-TYPE
This notification will be sent when config file analyze fails.
1.3.6.1.4.1.9.9.618.0.9current
ciscoLwappWlcUpgradeFail
NOTIFICATION-TYPE
This notification is generated when the wlc upgrade fails.
1.3.6.1.4.1.9.9.618.0.10current
ciscoLwappRAIDStatus
NOTIFICATION-TYPE
This notification is generated when the wlc hard disc status changes.
1.3.6.1.4.1.9.9.618.0.11current
ciscoLwappPortLinkSpeedTrap
NOTIFICATION-TYPE
This notification is generated when link speed changes in MGIG port.
1.3.6.1.4.1.9.9.618.0.12current

Conformance

NameOIDStatus
ciscoLwappSysMIBCompliance
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module.
1.3.6.1.4.1.9.9.618.2.1.1deprecated
ciscoLwappSysMIBComplianceRev1
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module.
1.3.6.1.4.1.9.9.618.2.1.2deprecated
ciscoLwappSysMIBComplianceRev2
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. This deprecates ciscoLwappSysMIBComplianceRev1.
1.3.6.1.4.1.9.9.618.2.1.3deprecated
ciscoLwappSysMIBComplianceRev3
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. This deprecates ciscoLwappSysMIBComplianceRev1.
1.3.6.1.4.1.9.9.618.2.1.4deprecated
ciscoLwappSysMIBComplianceRev4
MODULE-COMPLIANCE
The compliance statement for the SNMP entities that implement the ciscoLwappSysMIB module. This deprecates ciscoLwappSysMIBComplianceRev1.
1.3.6.1.4.1.9.9.618.2.1.5current
ciscoLwappSysConfigGroup
OBJECT-GROUP
This collection of objects represent the system wide configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.1current
ciscoLwappSysConfigFileEncryptionGroup
OBJECT-GROUP
This object represents the System encryption configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.2current
ciscoLwappSysConfigGroupSup1
OBJECT-GROUP
This collection of objects represents the timzone and syslog configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.3current
ciscoLwappSysTransferOperationConfigGroup
OBJECT-GROUP
This object represents the System Transfer operation configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.4current
ciscoLwappSysPortConfigGroup
OBJECT-GROUP
This collection of objects represent the system wide configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.5current
ciscoLwappSysSecurityConfigGroup
OBJECT-GROUP
This collection of objects represent the system security configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.6current
ciscoLwappSysIgmpConfigGroup
OBJECT-GROUP
This collection of objects represent the IGMP multicast configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.7current
ciscoLwappSysSecNotifObjsGroup
OBJECT-GROUP
This collection of objects represent the information carried by the security related notifications sent by the agent to a network management station.
1.3.6.1.4.1.9.9.618.2.2.8current
ciscoLwappSysNotifsGroup
NOTIFICATION-GROUP
This collection of objects represent the system config related notifications sent by the agent to a network management station.
1.3.6.1.4.1.9.9.618.2.2.9current
ciscoLwappSysNotifControlGroup
OBJECT-GROUP
This collection of objects represent the flags to control the generation of notification.
1.3.6.1.4.1.9.9.618.2.2.10current
ciscoLwappSysConfigGroupVer1
OBJECT-GROUP
This collection of objects represent the system wide configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.11deprecated
ciscoLwappSysStatsConfigGroup
OBJECT-GROUP
This collection of objects represents the statistics intervals configtation on the controller.
1.3.6.1.4.1.9.9.618.2.2.12current
ciscoLwappSysInfoGroup
OBJECT-GROUP
This collection of objects represent System Information configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.13current
ciscoLwappLyncInfoGroup
OBJECT-GROUP
This collection of objects represent System Information configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.14current
ciscoLwappSysMulticastMLDGroup
OBJECT-GROUP
This collection of objects represent Multicast MLD configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.15current
ciscoLwappSysConfigGroupVer2
OBJECT-GROUP
This collection of objects represent the system wide configuration on the controller.
1.3.6.1.4.1.9.9.618.2.2.16current