CISCO-IVR-MIB
- Registered at
- 1.3.6.1.4.1.9.9.371
- Last updated
- 2005-03-03 00:00
- Organization
- Cisco Systems Inc.
- Revisions
- 2005-03-03 00:00, 2004-10-27 00:00, 2003-11-03 00:00, 2003-10-20 00:00
- Namespace
- cisco
- Source file
CISCO-IVR-MIB- Digest
sha256:2f121e819aea6a2c18c7e01ce8ab7a69986a792ff67ba59f83ff6e6ca2e0c047
Description
The MIB module for the management of Inter-VSAN routing within the framework of Cisco's Inter-VSAN Routing (IVR) Architecture. IVR allows traffic between VSANs. VSANs are logically separated Storage Area Networks (SANs) where traffic does not cross VSAN boundaries. Certain SAN applications need restricted communication between initiators and targets which are in different VSANs. This MIB enables the users to manage IVR. The VSANs logically separate a single physical fabric into multiple logical fabrics. Each of these physical fabrics are called Autonmous Fabrics. In addition to Inter-VSAN communication, IVR also enables communication between Autonomous Fabrics. Acronyms The following acronyms are used in this document: Lun: Logical Unit Number IV: Inter-VSAN IVR: Inter-VSAN Routing PWWN: Port World Wide Name AFID: Autonomous Fabric id
Contact
Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553 -NETS E-mail: cs-san@cisco.com
Imports
| From | Symbols |
|---|---|
| CISCO-SMI | ciscoMgmt |
| CISCO-ST-TC | DomainId, FcAddressId, FcNameId, VsanIndex |
| CISCO-VSAN-MIB | vsanIndex |
| CISCO-ZS-MIB | FcList, ZoneQosPriorityLevel |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Integer32, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, Unsigned32, iso |
| SNMPv2-TC | DisplayString, RowStatus, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
CISCO-IVR-MIB CISCO-NS-MIB CISCO-SMI CISCO-ST-TC CISCO-TC CISCO-VSAN-MIB CISCO-ZS-MIB IANAifType-MIB IF-MIB INET-ADDRESS-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Textual conventions
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| CIvrAutonomousFabricId TEXTUAL-CONVENTION The Autonomous Fabric identifier. This identifies a set of fibre channel devices like hosts, disks, switches which are under single administration. It is up to the administrator to assign these identifiers to the Autonomous Fabrics so that each of the physical fabrics are uniquely identified. If a fabric is not partitioned into Autonomous Fabrics, then value of 1 must be used. | current | |||
| CIvrChecksum TEXTUAL-CONVENTION The checksum computed from the object/group of objects specified in the object description. This is used by manager to check if the object or group of objects is same across devices in the fabric. Note that method use to compute this is implementation specific. | current | |||
| CIvrZoneMemberType TEXTUAL-CONVENTION Type of IV zone member. pwwnVsan - the member is identified by port WWN (World Wide Name) and VSAN. | current |
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| ciscoIvrMIBNotifications OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.0 | |||
| ciscoIvrMIBObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1 | |||
| cimIvrConfiguration OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1.1 | |||
| cimIvrGeneric OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1.1.1 | |||
| civrFcidNatMode OBJECT-TYPE Enable FCID and VSAN identifier translation cross VSAN boundaries. If the value is 'true', the VSAN identifier as well as the entire FCID of the end-devices would be modified as frames cross VSAN boundaries. | 1.3.6.1.4.1.9.9.371.1.1.1.1 | TruthValue | read-write | current |
| civrVsanTopologyAutoDisc OBJECT-TYPE Enable automatic VSAN topology discovery. If this value is 'true', automatic VSAN topology discovery is turned on. IVR processes would communicate with each other to provide a global view of the physical topology to all the IVR enabled switches. VSAN topology is configured through civrTopologyAfidConfTable and civrTopologyDefaultAfidTable when automatic VSAN topology discovery is turned on. If this value is 'false', automatic VSAN topology discovery is turned off. VSAN topology is manually configured by using civrTopologyConfigTable. | 1.3.6.1.4.1.9.9.371.1.1.1.2 | TruthValue | read-write | current |
| cimIvrZoneset OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1.1.2 | |||
| civrZoneSetNumber OBJECT-TYPE The number of entries currently present in the civrZoneSetTable. | 1.3.6.1.4.1.9.9.371.1.1.2.1 | Integer32 (0..8388608) | read-only | current |
| civrZoneSetTable OBJECT-TYPE A table containing information on each Inter-VSAN (IV) zonesets which are configured locally. It comprises the zonesets in the full IV zone database. There could be multiple IV zonesets configured. But only one zoneset is allowed to be active at a time. An IV zoneset is a collection of IV zones. | 1.3.6.1.4.1.9.9.371.1.1.2.2 | not-accessible | current | |
| civrZoneSetEntry OBJECT-TYPE An entry (conceptual row) in the civrZoneSetTable. The sequence of operations to be performed in order to create a zoneset is as follows: - create zone entries in the civrZoneTable. - create an entry in this table and set the civrZoneSetZoneList bitmap object to contain the required IV zones. - Note that it is perfectly valid to create an empty zoneset. | 1.3.6.1.4.1.9.9.371.1.1.2.2.1 | not-accessible | current | |
| civrZoneSetIndex OBJECT-TYPE The index of a zoneset. This object uniquely identifies an IV zoneset. This object could have the same value as civrZoneSetTableNextIndex. | 1.3.6.1.4.1.9.9.371.1.1.2.2.1.1 | Unsigned32 (1..2048) | not-accessible | current |
| civrZoneSetName OBJECT-TYPE The name of this zoneset. The civrZoneSetName should be unique on this device. This object cannot be modified while the corresponding value of civrZoneSetRowStatus is equal to 'active'. This object MUST be set before or concurrently with setting the corresponding instance of civrZoneSetRowStatus to 'active'. | 1.3.6.1.4.1.9.9.371.1.1.2.2.1.2 | SnmpAdminString (SIZE(1..64)) | read-create | current |
| civrZoneSetZoneList OBJECT-TYPE The set of IV zones which form this zoneset. The IV zones are identified by civrZoneIndex object in the civrZoneTable. If a particular bit has a value of '1', then the corresponding zone is a part of this zoneset. All other zones have '0' in their positions or not present in the string. Note that an IV zone can be part of multiple IV zonesets. | 1.3.6.1.4.1.9.9.371.1.1.2.2.1.3 | FcList | read-create | current |
| civrZoneSetLastChange OBJECT-TYPE The value of sysUpTime at the time of the last change to this IV zoneset entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value. | 1.3.6.1.4.1.9.9.371.1.1.2.2.1.4 | TimeStamp | read-only | current |
| civrZoneSetChecksum OBJECT-TYPE The checksum of content of this zoneset. | 1.3.6.1.4.1.9.9.371.1.1.2.2.1.5 | CIvrChecksum | read-only | current |
| civrZoneSetRowStatus OBJECT-TYPE The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of civrZoneSetName is unique. | 1.3.6.1.4.1.9.9.371.1.1.2.2.1.6 | RowStatus | read-create | current |
| civrZoneSetActivate OBJECT-TYPE Setting this object to a value is a request for a particular IV zoneset to be activated on this device. i.e., for the current configuration of that zoneset to be cloned with the clone becoming the active zoneset. Setting this object to a value (say, N) identifies the IV zoneset to be cloned as the zoneset identified by civrZoneSetIndex object having the same value N. Even though there could be multiple IV zonesets on this device, only one can be active at a time. If a IV zoneset is already active and a second IV zone set is activated, then the first IV zoneset is automatically deactivated and the second IV zoneset is activated. The IV zoneset activation is done only in 'activate VSANs' on the local device. The 'activate VSANs' is the intersection of topology VSANs on the local device (civrTopologyActiveSwitchVsan2k and civrTopologyActiveSwitchVsan4k), members VSANs (union of all the VSANs of the members in the zoneset being activated) and local VSANs (vsanTable from CISCO-VSAN-MIB). If the activation was successful then, civrZoneEnforcedZoneSetName contains the name of zoneset corresponding to the civrZoneSetIndex that was set. The value of this object when read is always 0. | 1.3.6.1.4.1.9.9.371.1.1.2.3 | Unsigned32 (0..2048) | read-write | current |
| civrZoneSetActvatDeactvatResult OBJECT-TYPE This object indicates the outcome of the most recent activation/deactivation. activateSuccess - activation success activateFailureNoMembers - activation failure because of no members in the zoneset activateFailureZoneOneorLessMem - activation failure as the zoneset being activated contained one or less member. activateFailureNoTopology - activation failure because of no IVR topology activateFailureNoPerVsanSucc - activation failed in all 'activate VSANs' activateFailureNoZoneset - activation failure because of no zoneset activateFailureNoVsans - activation failure because of no 'activate VSANs' activateFailureFabricUnstable - activation failure because fabric unstable deactivateSuccess - deactivation success deactivateFailureNoActiveZs - no active zoneseset deactivateFailureNoPerVsanSucc - deactivation failed in all 'activate VSANs' deactivateFailureFabricUnstable - deactivation failed because fabric is unstable activating - activation in progress deactivating - deactivation in progress idle - idle deactivateSuccessFcNatShutup13 - deactivation success, shutup 1.3 switch in NAT mode activateFailureFabric - none of the switches connected to the fabric is able to activate this zoneset deactivateFailureFabric - none of the switches connected to the fabric is able to deactivate this zoneset activatePartialSuccessFabric - activation succeeds on some of the switches connected to this fabric deactivatePartialSuccessFabric - deactivation succeeds on some of the switches connected to this fabric deviceCleanupInProgress - device cleanup is in progress during deactivation activatingReadyToAdv - switches connected to this fabric are ready to advertise device changes activatingAdvertising - switches connected to this fabric are advertising device change information When the value of this object is either 'activating', or 'deactivating', the values of of civrZoneSetActivate and civrZoneSetDeActivate respectively cannot be modified. | 1.3.6.1.4.1.9.9.371.1.1.2.4 | INTEGER {activateSuccess(1), activateFailureNoMembers(2), activateFailureZoneOneorLessMem(3), activateFailureNoTopology(4), activateFailureNoPerVsanSucc(5), activateFailureNoZoneset(6), activateFailureNoVsans(7), activateFailureFabricUnstable(8), deactivateSuccess(9), deactivateFailureNoActiveZs(10), deactivateFailureNoPerVsanSucc(11), deactivateFailureFabricUnstable(12), activating(13), deactivating(14), idle(15), deactivateSuccessFcNatShutup13(16), activateFailureFabric(17), deactivateFailureFabric(18), activatePartialSuccessFabric(19), deactivatePartialSuccessFabric(20), deviceCleanupInProgress(21), activatingReadyToAdv(22), activatingAdvertising(23)} | read-only | current |
| civrZoneSetDeActivate OBJECT-TYPE Setting this object to 'deactivate' is a request to deactivate the currently active IV zoneset. deactivate - deactivate IV zoneset noop - no operation No action is taken if this object is set to 'noop'. The value of this object when read is always 'noop'. | 1.3.6.1.4.1.9.9.371.1.1.2.5 | INTEGER {deactivate(1), noop(2)} | read-write | current |
| civrZonesetDbChecksum OBJECT-TYPE The checksum of the full IV zone database. | 1.3.6.1.4.1.9.9.371.1.1.2.6 | CIvrChecksum | read-only | current |
| civrActiveZonesetChecksum OBJECT-TYPE The checksum of the enforced (active) IV zoneset. | 1.3.6.1.4.1.9.9.371.1.1.2.7 | CIvrChecksum | read-only | current |
| civrZoneEnforcedZoneSetName OBJECT-TYPE The name of the enforced IV zoneset. | 1.3.6.1.4.1.9.9.371.1.1.2.8 | SnmpAdminString (SIZE(1..64)) | read-only | current |
| civrZoneEnforcedZoneSetZoneList OBJECT-TYPE The set of IV zones which form this IV zoneset. This object was copied from the civrZoneSetZoneList object in the civrZoneSetTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.2.9 | FcList | read-only | current |
| civrZoneEnforcedZoneSetActvtTime OBJECT-TYPE The sysUpTime at which enforced zoneset was most recently activated. If this entry has been activated prior to the last re-initialization of the local network management system, then this object will contain a zero value. | 1.3.6.1.4.1.9.9.371.1.1.2.10 | TimeStamp | read-only | current |
| civrZoneCopyZoneSetEnforcdToFull OBJECT-TYPE This object copies the enforced IV zoneset (active IV zoneset) into the full IV zone database Setting this object to 'copy' will trigger the copy of the enforced IV zoneset to the full IV zone database. If there is no enforced IV zoneset, the copy will result in an error. No action is taken if this object is set to 'noOp'. | 1.3.6.1.4.1.9.9.371.1.1.2.11 | INTEGER {copy(1), noOp(2)} | read-write | current |
| civrZoneClearFullZoneDb OBJECT-TYPE This object clears the full IVR zone database. Setting this object to 'clear' will clear the full IV zone database. No action is taken if this object is set to 'noOp'. | 1.3.6.1.4.1.9.9.371.1.1.2.12 | INTEGER {clear(1), noOp(2)} | read-write | current |
| civrZonesetActivateForce OBJECT-TYPE The force option for IV zoneset activation. Following things are done if this object is 'true': - If there is no regular active zoneset in a VSAN (no entry present zoneEnforcedZoneSetTable from CISCO-ZS-MIB for that VSAN), then a regular active zoneset will be created and the IV zones will be added to the active zoneset. - if the default zone behaviour (as indicated by object zoneDefaultZoneBehaviour from CISCO-ZS-MIB) is 'permit', then the IV zones will be added to the regular active zoneset. If the value of this object is 'false', the IV zones are added to the regular active zoneset only in the case of default zone behaviour is 'deny'. | 1.3.6.1.4.1.9.9.371.1.1.2.13 | TruthValue | read-write | current |
| civrZoneSetTableNextIndex OBJECT-TYPE This object specifies the next available index for object civrZoneSetIndex which can be used for creating an entry in civrZoneSetTable. | 1.3.6.1.4.1.9.9.371.1.1.2.14 | Unsigned32 | read-only | current |
| cimIvrZone OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1.1.3 | |||
| civrZoneNumber OBJECT-TYPE The number of entries currently present in the civrZoneTable. | 1.3.6.1.4.1.9.9.371.1.1.3.1 | Integer32 (0..65535) | read-only | current |
| civrZoneTable OBJECT-TYPE This table gives information on all the IV zones and lists all their members. IV zones is group of IV members (FC devices like hosts, disks) in different VSANs. | 1.3.6.1.4.1.9.9.371.1.1.3.2 | not-accessible | current | |
| civrZoneEntry OBJECT-TYPE An entry (conceptual row) in the civrZoneTable. These are the zones in the full IV zone database. The sequence of operations to be performed in order to create a IV Zone is as follows: - create an entry in this table. - create IV zone members in the civrZoneMemberTable that belong to this IV zone. | 1.3.6.1.4.1.9.9.371.1.1.3.2.1 | not-accessible | current | |
| civrZoneIndex OBJECT-TYPE The index of an IV Zone. This object could have the same value as civrZoneTableNextIndex. | 1.3.6.1.4.1.9.9.371.1.1.3.2.1.1 | Unsigned32 (1..2048) | not-accessible | current |
| civrZoneName OBJECT-TYPE The name of this zone. The zoneName should be unique this device. This object can not be modified while the corresponding value of civrZoneRowStatus is 'active'. This object MUST be set before or concurrently with setting the corresponding instance of civrZoneRowStatus to 'active'. | 1.3.6.1.4.1.9.9.371.1.1.3.2.1.2 | SnmpAdminString (SIZE(1..58)) | read-create | current |
| civrZoneMemberList OBJECT-TYPE The set of IV Zone members that form this IV zone. The IV zone members are identified by civrZoneMemberIndex object in the civrZoneMemberTable. If a particular bit has a value of '1', then the corresponding zone member is a part of this zone. All other zone members have '0' in their positions or not present in the string. This object is read-only; changes to its value are made by the agent as and when associated entries are created/deleted in the civrZoneMemberTable. The default value is the zero length string. | 1.3.6.1.4.1.9.9.371.1.1.3.2.1.3 | FcList | read-only | current |
| civrZoneLastChange OBJECT-TYPE The value of sysUpTime at the time of the last change to this IV zone entry. If the entry has not been modified since the last re-initialization of the local network management system, then this object will contain a zero value. | 1.3.6.1.4.1.9.9.371.1.1.3.2.1.5 | TimeStamp | read-only | current |
| civrZoneRowStatus OBJECT-TYPE The status of this conceptual row. This object can not be set to 'active' unless the corresponding value of zoneName is unique on this device. | 1.3.6.1.4.1.9.9.371.1.1.3.2.1.6 | RowStatus | read-create | current |
| civrZoneReadOnly OBJECT-TYPE This object indicates if only SCSI read operations are allowed on members of this IV zone which are SCSI targets. If this object is set to 'true', then only SCSI read operations are permitted. So, this IV zone becomes a read-only IV zone. If this object is set to 'false', then both SCSI read and write operations are permitted in this IV zone. | 1.3.6.1.4.1.9.9.371.1.1.3.2.1.7 | TruthValue | read-create | current |
| civrZoneQosPriority OBJECT-TYPE This object specifies if qos attribute for this IV zone is enabled. If this object is set to a value other than 'none', then qos attribute for this IV zone is enabled. If this object is set to 'none', then qos attribute for this IV zone is disabled. If this attribute is enabled for this IV zone, then only traffic with the configured priority level will be allowed between the members of this IV zone. | 1.3.6.1.4.1.9.9.371.1.1.3.2.1.8 | ZoneQosPriorityLevel | read-create | current |
| civrZoneEnforcedZoneNumber OBJECT-TYPE The number of entries currently present in the civrZoneEnforcedZoneTable. | 1.3.6.1.4.1.9.9.371.1.1.3.3 | Integer32 (0..8388608) | read-only | current |
| civrZoneEnforcedZoneTable OBJECT-TYPE This table contains all the IV zones that are present in the active IV zoneset. | 1.3.6.1.4.1.9.9.371.1.1.3.4 | not-accessible | current | |
| civrZoneEnforcedZoneEntry OBJECT-TYPE An entry (conceptual row) in this table. | 1.3.6.1.4.1.9.9.371.1.1.3.4.1 | not-accessible | current | |
| civrZoneEnforcedZoneName OBJECT-TYPE The name of this zone. | 1.3.6.1.4.1.9.9.371.1.1.3.4.1.1 | SnmpAdminString (SIZE(1..58)) | read-only | current |
| civrZoneEnforcedZoneMemberList OBJECT-TYPE The set of members that form this IV zone. This object was copied from the civrZoneMemberList object in the civrZoneTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.3.4.1.2 | FcList | read-only | current |
| civrZoneEnforcedZoneReadOnly OBJECT-TYPE This object indicates whether this is a read-only IV zone. This object was copied from the civrZoneReadOnly object in the civrZoneTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.3.4.1.3 | TruthValue | read-only | current |
| civrZoneEnforcedZoneQosPriority OBJECT-TYPE This object indicates whether this is a qos enabled IV zone. This object was copied from the civrZoneQosPriority object in the civrZoneTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.3.4.1.4 | ZoneQosPriorityLevel | read-only | current |
| civrZoneTableNextIndex OBJECT-TYPE This object specifies the next available index for object civrZoneIndex which can be used for creating an entry in civrZoneTable. | 1.3.6.1.4.1.9.9.371.1.1.3.5 | Unsigned32 | read-only | current |
| cimIvrZoneMember OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1.1.4 | |||
| civrZoneMemberNumber OBJECT-TYPE The number of entries currently present in the civrZoneMemberTable. | 1.3.6.1.4.1.9.9.371.1.1.4.1 | Integer32 (0..16777216) | read-only | current |
| civrZoneMemberTable OBJECT-TYPE This table contains all members of all the IV Zones in the civrZoneTable and information about those members. These are the members part of full IV zone database. | 1.3.6.1.4.1.9.9.371.1.1.4.2 | not-accessible | current | |
| civrZoneMemberEntry OBJECT-TYPE An entry (conceptual row) in the civrZoneMemberTable. Each entry represents the relationship between a member and (one of) its 'parent(s)', i.e., an IV zone to which the member belongs to. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1 | not-accessible | current | |
| civrZoneMemberParentIndex OBJECT-TYPE This object contains the value of the index of the IV zone to which this member belongs to. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1.1 | Unsigned32 (1..2048) | not-accessible | current |
| civrZoneMemberIndex OBJECT-TYPE The index of this IV zone member on this IV zone. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1.2 | Unsigned32 (1..2048) | not-accessible | current |
| civrZoneMemberType OBJECT-TYPE The type of IV Zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1.3 | CIvrZoneMemberType | read-create | current |
| civrZoneMemberID OBJECT-TYPE This object represents the IV zone member ID. If civrZoneMemberType is 'pwwnVsan', this object contains port WWN. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1.4 | OCTET STRING | read-create | current |
| civrZoneMemberAFId OBJECT-TYPE The Autonomous Fabric identifier of this IV zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1.5 | CIvrAutonomousFabricId | read-create | current |
| civrZoneMemberVsan OBJECT-TYPE The VSAN of this IV zone member. This object cannot be modified while the corresponding value of civrZoneMemberRowStatus object is 'active'. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1.6 | VsanIndex | read-create | current |
| civrZoneMemberRowStatus OBJECT-TYPE The status of this conceptual row. civrMemberType, civrZoneMemberID and civrZoneMemberVsan objects MUST be set before or concurrently with setting the corresponding instance of civrZoneMemberRowStatus to 'active'. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1.7 | RowStatus | read-create | current |
| civrZoneMemberLunID OBJECT-TYPE This object specifies the Lun ID if IV Lun zoning is configured. If this object is the zero-length string, then IV Lun zoning is not configured. This object cannot be modified while the corresponding value of zoneMemberRowStatus object is 'active'. | 1.3.6.1.4.1.9.9.371.1.1.4.2.1.8 | OCTET STRING (SIZE(0 | 8)) | read-create | current |
| civrZoneEnforcedZoneMemberNumber OBJECT-TYPE The number of entries currently present in the civrZoneEnforcedZoneMemberTable. | 1.3.6.1.4.1.9.9.371.1.1.4.3 | Integer32 (0..16777216) | read-only | current |
| civrZoneEnforcedZoneMemberTable OBJECT-TYPE This table contains all members that are part of a IV zone and are part of the active IV zone set. | 1.3.6.1.4.1.9.9.371.1.1.4.4 | not-accessible | current | |
| civrZoneEnforcedZoneMemberEntry OBJECT-TYPE An entry (conceptual row) in this table. | 1.3.6.1.4.1.9.9.371.1.1.4.4.1 | not-accessible | current | |
| civrZoneEnforcedZoneMemberType OBJECT-TYPE The type of IV zone member. This object was copied from the civrZoneMemberType object in the civrZoneMemberTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.4.4.1.2 | CIvrZoneMemberType | read-only | current |
| civrZoneEnforcedZoneMemberID OBJECT-TYPE This object represents this member's address. This object was copied from the civrZoneMemberID object in the civrZoneMemberTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.4.4.1.3 | OCTET STRING | read-only | current |
| civrZoneEnforcedZoneMemberAFId OBJECT-TYPE The Autonomous Fabric identifier of the member. This object was copied from the civrZoneMemberAFId object in the civrZoneMemberTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.4.4.1.4 | CIvrAutonomousFabricId | read-only | current |
| civrZoneEnforcedZoneMemberVsan OBJECT-TYPE The VSAN of the member. This object was copied from the civrZoneMemberVsan object in the civrZoneMemberTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.4.4.1.5 | VsanIndex | read-only | current |
| civrZoneEnforcedZoneMemberLunID OBJECT-TYPE This object specifies the Lun ID if IV Lun zoning is configured. This object was copied from the civrZoneMemberLunID object in the civrZoneMemberTable at the time when the currently active zoneset was activated. | 1.3.6.1.4.1.9.9.371.1.1.4.4.1.6 | OCTET STRING (SIZE(0 | 8)) | read-only | current |
| cimIvrTopology OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1.1.5 | |||
| civrTopologyConfiguredChecksum OBJECT-TYPE The checksum of the configured IVR topology. | 1.3.6.1.4.1.9.9.371.1.1.5.1 | CIvrChecksum | read-only | current |
| civrTopologyConfigTable OBJECT-TYPE This table contains the configured IVR topology. The topology is specified in terms of one or more Autonomous Fabrics made of switches and the VSANs to/from which the switches provide connectivity. The configured topology is not applied until it is made active using using object civrTopologyActivate. | 1.3.6.1.4.1.9.9.371.1.1.5.2 | not-accessible | current | |
| civrTopologyConfigEntry OBJECT-TYPE An entry (conceptual row) in this table. | 1.3.6.1.4.1.9.9.371.1.1.5.2.1 | not-accessible | current | |
| civrTopologyConfigSwitchWwn OBJECT-TYPE The configured switch WWN of this device. | 1.3.6.1.4.1.9.9.371.1.1.5.2.1.1 | FcNameId | not-accessible | current |
| civrTopologyConfigAutoFabricId OBJECT-TYPE The configured Autonomous Fabric id of this device. | 1.3.6.1.4.1.9.9.371.1.1.5.2.1.2 | CIvrAutonomousFabricId | not-accessible | current |
| civrTopologyConfigSwitchVsan2k OBJECT-TYPE The list of configured VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyConfigSwitchVsan4k are zero-length string, then the IVR topology contains only the default VSAN. | 1.3.6.1.4.1.9.9.371.1.1.5.2.1.3 | FcList | read-create | current |
| civrTopologyConfigSwitchVsan4k OBJECT-TYPE The list of configured VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2047 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and corresponding instance of civrTopologyConfigSwitchVsan2k are zero-length string, then the IVR topology contains only the default VSAN. | 1.3.6.1.4.1.9.9.371.1.1.5.2.1.4 | FcList | read-create | current |
| civrTopologyConfigRowStatus OBJECT-TYPE Status of this row. | 1.3.6.1.4.1.9.9.371.1.1.5.2.1.5 | RowStatus | read-create | current |
| civrTopologyActivate OBJECT-TYPE Setting this object to 'activate' is a request for the configured IVR topology to be activated on this device. i.e., for the current configuration of IVR topology to be cloned, with the clone becoming the active IVR topology (civrTopologyActiveTable). The value of this object when read is always 'noOp'. | 1.3.6.1.4.1.9.9.371.1.1.5.3 | INTEGER {activate(1), noOp(2)} | read-write | current |
| civrTopologyActivateTime OBJECT-TYPE The sysUpTime at which the IVR topology was most recently activated. If the IVR topology has not been activated prior to the last re-initialization of the local network management system, then this object will contain a zero value. | 1.3.6.1.4.1.9.9.371.1.1.5.4 | TimeStamp | read-only | current |
| civrTopologyCopyActiveToConfig OBJECT-TYPE This object copies the active IVR topology table to configured IVR topology table. If there is no active IVR topology, the copy will result in an error. No action is taken if this object is set to 'noOp'. | 1.3.6.1.4.1.9.9.371.1.1.5.5 | INTEGER {copy(1), noOp(2)} | read-write | current |
| civrTopologyClearConfigured OBJECT-TYPE This object clears the configured IVR topology table. No action is taken if this object is set to 'noOp'. | 1.3.6.1.4.1.9.9.371.1.1.5.6 | INTEGER {clear(1), noOp(2)} | read-write | current |
| civrTopologyActiveChecksum OBJECT-TYPE The checksum of the active IVR topology. | 1.3.6.1.4.1.9.9.371.1.1.5.7 | CIvrChecksum | read-only | current |
| civrTopologyActiveTable OBJECT-TYPE This table contains the IVR topology. The topology is specified in terms of one or more Autonomous Fabrics made of switches and the VSANs to/from which the switches provide connectivity. | 1.3.6.1.4.1.9.9.371.1.1.5.8 | not-accessible | current | |
| civrTopologyActiveEntry OBJECT-TYPE An entry (conceptual row) in this table. | 1.3.6.1.4.1.9.9.371.1.1.5.8.1 | not-accessible | current | |
| civrTopologyActiveSwitchWwn OBJECT-TYPE The switch WWN of this device. | 1.3.6.1.4.1.9.9.371.1.1.5.8.1.1 | FcNameId | not-accessible | current |
| civrTopologyActiveAutoFabricId OBJECT-TYPE The Autonomous Fabric id of this device. | 1.3.6.1.4.1.9.9.371.1.1.5.8.1.2 | CIvrAutonomousFabricId | not-accessible | current |
| civrTopologyActiveSwitchVsan2k OBJECT-TYPE The list of VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyActiveSwitchVsan4k are zero-length string, then the IVR topology contains only the default VSAN. | 1.3.6.1.4.1.9.9.371.1.1.5.8.1.3 | FcList | read-only | current |
| civrTopologyActiveSwitchVsan4k OBJECT-TYPE The list of VSANs that are part of IVR topology on this device. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2047 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the IVR topology on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and corresponding instance of civrTopologyActiveSwitchVsan2k are zero-length string, then the IVR topology contains only the default VSAN. | 1.3.6.1.4.1.9.9.371.1.1.5.8.1.4 | FcList | read-only | current |
| civrTopologyActive OBJECT-TYPE This object indicates of IVR topology is active or not. If 'true', the IVR topology is active. And if it is 'false', the IVR topology is not active. | 1.3.6.1.4.1.9.9.371.1.1.5.9 | TruthValue | read-only | current |
| civrTopologyAfidConfigChecksum OBJECT-TYPE The checksum of the Autonomous Fabric id (AFID) configurations. | 1.3.6.1.4.1.9.9.371.1.1.5.10 | CIvrChecksum | read-only | current |
| civrTopologyAfidConfTable OBJECT-TYPE This table contains the Autonomous Fabric id (AFID) configurations when automatic VSAN topology discovery is activated. An entry (conceptual row) in this table represents an AFID and its VSANs on a switch. | 1.3.6.1.4.1.9.9.371.1.1.5.11 | not-accessible | current | |
| civrTopologyAfidConfEntry OBJECT-TYPE An entry (conceptual row) in this table. | 1.3.6.1.4.1.9.9.371.1.1.5.11.1 | not-accessible | current | |
| civrTopologyAfidConfSwitchWwn OBJECT-TYPE The switch WWN of this device. | 1.3.6.1.4.1.9.9.371.1.1.5.11.1.1 | FcNameId | not-accessible | current |
| civrTopologyAfidConfId OBJECT-TYPE The configured Autonomous Fabric id of this device. | 1.3.6.1.4.1.9.9.371.1.1.5.11.1.2 | CIvrAutonomousFabricId | not-accessible | current |
| civrTopologyAfidConfSwitchVsan2k OBJECT-TYPE The list of VSANs that are part of AFID (Autonomous Fabric ID) specified by civrTopologyConfigAutoFabricId on switch specified by civrTopologyConfigSwitchWwn. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this AFID on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyAfidConfSwitchVsan4k are zero-length string, then the AFID configured on this device contains only the default VSAN. | 1.3.6.1.4.1.9.9.371.1.1.5.11.1.3 | FcList | read-create | current |
| civrTopologyAfidConfSwitchVsan4k OBJECT-TYPE The list of VSANs that are part of AFID (Autonomous Fabric ID) specified by civrTopologyConfigAutoFabricId on switch specified by civrTopologyConfigSwitchWwn. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this AFID on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and corresponding instance of civrTopologyAfidConfSwitchVsan2k are zero-length string, then the AFID configured on this device contains only the default VSAN. | 1.3.6.1.4.1.9.9.371.1.1.5.11.1.4 | FcList | read-create | current |
| civrTopologyAfidConfRowStatus OBJECT-TYPE Status of this row. | 1.3.6.1.4.1.9.9.371.1.1.5.11.1.5 | RowStatus | read-create | current |
| civrTopologyDefaultAfidChecksum OBJECT-TYPE The checksum of the configured default AFIDs. | 1.3.6.1.4.1.9.9.371.1.1.5.12 | CIvrChecksum | read-only | current |
| civrTopologyDefaultAfidTable OBJECT-TYPE This table contains the default Autonomous Fabric id (AFID) configurations when automatic VSAN topology discovery is activated. An entry (conceptual row) in this table represents the default AFID for a switch. | 1.3.6.1.4.1.9.9.371.1.1.5.13 | not-accessible | current | |
| civrTopologyDefaultAfidEntry OBJECT-TYPE An entry (conceptual row) in this table. | 1.3.6.1.4.1.9.9.371.1.1.5.13.1 | not-accessible | current | |
| civrTopologyDefaultAfidSwitchWwn OBJECT-TYPE The switch WWN of this device. | 1.3.6.1.4.1.9.9.371.1.1.5.13.1.1 | FcNameId | not-accessible | current |
| civrTopologyDefaultAfidId OBJECT-TYPE The configured Default Autonomous Fabric id of this switch. | 1.3.6.1.4.1.9.9.371.1.1.5.13.1.2 | CIvrAutonomousFabricId | read-create | current |
| civrTopologyDefaultAfidStatus OBJECT-TYPE Status of this row. | 1.3.6.1.4.1.9.9.371.1.1.5.13.1.3 | RowStatus | read-create | current |
| civrTopologyIvrSrvGrpTable OBJECT-TYPE This table contains configurations of Inter-VSAN Routing (IVR) Service Group. An Inter VSAN Routing Service Group defines a logical boundary for Inter-VSAN Routing. Inter-VSAN Routing is restricted among VSANs within their own Inter-VSAN Routing Service Group only. | 1.3.6.1.4.1.9.9.371.1.1.5.14 | not-accessible | current | |
| civrTopologyIvrSrvGrpEntry OBJECT-TYPE An entry (conceptual row) in this table. | 1.3.6.1.4.1.9.9.371.1.1.5.14.1 | not-accessible | current | |
| civrTopologyIvrSrvGrpName OBJECT-TYPE This object contains the name of the IVR Service Group corresponding to this conceptual row. | 1.3.6.1.4.1.9.9.371.1.1.5.14.1.1 | SnmpAdminString (SIZE(1..80)) | not-accessible | current |
| civrTopologyIvrSrvGrpVsan2k OBJECT-TYPE The list of VSANs that are part of this IVR Service Group specified by civrTopologyIvrSrvGrpName. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this IVR Service Group if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. | 1.3.6.1.4.1.9.9.371.1.1.5.14.1.2 | FcList | read-create | current |
| civrTopologyIvrSrvGrpVsan4k OBJECT-TYPE The list of VSANs that are part of this IVR Service Group specified by civrTopologyIvrSrvGrpName. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2054, the second octet specifying VSANs 2055 through 2062, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in this IVR Service Group if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. | 1.3.6.1.4.1.9.9.371.1.1.5.14.1.3 | FcList | read-create | current |
| civrTopologyIvrSrvGrpRowStatus OBJECT-TYPE Status of this row. | 1.3.6.1.4.1.9.9.371.1.1.5.14.1.4 | RowStatus | read-create | current |
| civrTopologyClearAfidConfig OBJECT-TYPE This object clears the AFID configuration table, civrTopologyAfidConfTable, if this object is set to 'clear'. No action is taken if this object is set to 'noOp'. | 1.3.6.1.4.1.9.9.371.1.1.5.15 | INTEGER {clear(1), noOp(2)} | read-write | current |
| cimIvrVirtualDomains OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1.1.6 | |||
| civrAddIvrVirtualDomainsVsans2k OBJECT-TYPE This object lists VSANs in which the virtual domains in a VSAN are added to the domain list (dmDatabaseTable in CISCO-DM-MIB) in that VSAN. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 0 through 7, the second octet specifying VSANs 8 through 15, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the add virtual domain VSAN list on this device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in this list. If the values of both this object and civrAddIvrVirtualDomainsVsans4k are zero-length string, then the Virtual Domains are not added to any VSANs. | 1.3.6.1.4.1.9.9.371.1.1.6.1 | FcList | read-write | current |
| civrAddIvrVirtualDomainsVsans4k OBJECT-TYPE This object lists VSANs in which the virtual domains in a VSAN are added to the domain list (dmDatabaseTable in CISCO-DM-MIB) in that VSAN. Each octet within the value of this object specifies a set of eight VSANs, with the first octet specifying VSANs 2048 through 2055, the second octet specifying VSANs 2056 through 2063, etc. Within each octet, the most significant bit represents the lowest numbered VSAN, and the least significant bit represents the highest numbered VSAN. Thus, each VSAN, is represented by a single bit within the value of this object. The corresponding VSAN is contained in the add virtual domain VSAN list on device if and only if that bit has a value of '1'. If this object has a value which is less than 256 bytes long, then the VSANs which are not represented are not considered to be in the list. If the values of both this object and civrAddIvrVirtualDomainsVsans2k are zero-length string, then the Virtual Domains are not added to any VSANs. | 1.3.6.1.4.1.9.9.371.1.1.6.2 | FcList | read-write | current |
| cimIvrStats OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.1.2 | |||
| civrZoneSetStatusTable OBJECT-TYPE A table containing status of the current active IV Zoneset on each local VSANs. | 1.3.6.1.4.1.9.9.371.1.2.1 | not-accessible | current | |
| civrZoneSetStatusEntry OBJECT-TYPE An entry (conceptual row) in the civrZoneSetStatusTable. | 1.3.6.1.4.1.9.9.371.1.2.1.1 | not-accessible | current | |
| civrZoneSetStatus OBJECT-TYPE Status of the active IV Zoneset on this VSAN. idle - idle active - active deactive - deactive defaultZoneDeny - activation failed because of default zone behaviour is deny and there is no regular active zoneset. activationFailed - activation failed (check zoneSetFailCause in CISCO-ZS-MIB for this VSAN) deactivationFailed - deactivation failed (check zoneSetFailCause in CISCO-ZS-MIB for this VSAN) activationNotInitiated - activation not initiated activationFailedFabricChgFailed - activation failed because of fabric change failed deactivationNotInitiated - deactivation not initiated deactivationFailedFabChgFailed - deactivation failed because of fabric changing activating - activation in progress activatingWaitForLowestSwwn - activation in progress; waiting for the lowest switch WWN switch to add IV zoneset to the regular active zoneset. activatingFabricChanging - activation in progress; fabric is changing deactivating - deactivation in progress deactivatingWaitForLowestSwwn - deactivation in progress; waiting for the lowest switch WWN switch to delete IV zoneset from the regular active zoneset. deactivatingFabricChanging - deactivation in progress; fabric is changing defaultZonePermit - activation failed because of default zone behaviour is permit defaultZonePermitNoForce - activation failed because of default zone behaviour is permit with no force option defaultZonePermitActZsNoForce - activation failed because of default zone behaviour is permit and with regular activate zoneset and no force option denyNoActiveZoneset - activation failed because there is no active zoneset activationFailedLowestWwnWait - activation failed waiting for switch with lowest wwn to activate this zoneset deactivationFailedLowestWwnWait - deactivation failed waiting for switch with lowest wwn to deactivate this zoneset . | 1.3.6.1.4.1.9.9.371.1.2.1.1.1 | INTEGER {idle(1), active(2), deactive(3), defaultZoneDeny(4), activationFailed(5), deactivationFailed(6), activationNotInitiated(7), activationFailedFabricChgFailed(8), deactivationNotInitiated(9), deactivationFailedFabChgFailed(10), activating(11), activatingWaitForLowestSwwn(12), activatingFabricChanging(13), deactivating(14), deactivatingWaitForLowestSwwn(15), deactivatingFabricChanging(16), defaultZonePermit(17), defaultZonePermitNoForce(18), defaultZonePermitActZsNoForce(19), denyNoActiveZoneset(20), activationFailedLowestWwnWait(21), deactivationFailedLowestWwnWait(22)} | read-only | current |
| civrEnabledDeviceTable OBJECT-TYPE This table contains the all IVR enabled devices known to the local device on each of the local VSANs. Note that the devices are learned using an internal protocol. So if a device in this table is not reachable, anymore from the local switch, then it is removed from this table. Also, if a new device is learned, it is added to this table. | 1.3.6.1.4.1.9.9.371.1.2.2 | not-accessible | current | |
| civrEnabledDeviceEntry OBJECT-TYPE An entry (conceptual row) in this table. Each entry represents a device in a particular VSAN. | 1.3.6.1.4.1.9.9.371.1.2.2.1 | not-accessible | current | |
| civrEnabledDeviceVsan OBJECT-TYPE The VSAN corresponding to this entry. | 1.3.6.1.4.1.9.9.371.1.2.2.1.1 | VsanIndex | not-accessible | current |
| civrEnabledDeviceAutoFabricId OBJECT-TYPE The Autonomous Fabric id corresponding to this entry. | 1.3.6.1.4.1.9.9.371.1.2.2.1.2 | CIvrAutonomousFabricId | not-accessible | current |
| civrEnabledDeviceDomainId OBJECT-TYPE The domain ID of this device corresponding this entry. | 1.3.6.1.4.1.9.9.371.1.2.2.1.3 | DomainId | not-accessible | current |
| civrEnabledDeviceSwitchWwn OBJECT-TYPE The switch WWN of this device. | 1.3.6.1.4.1.9.9.371.1.2.2.1.4 | FcNameId | read-only | current |
| civrEnabledDeviceCapability OBJECT-TYPE The switch WWN of this device. | 1.3.6.1.4.1.9.9.371.1.2.2.1.5 | Bits {version1(0)} | read-only | current |
| civrZoneMemberFabricId OBJECT-TYPE The fabric address of the IV zone member which is not able to participate in inter-VSAN communication because of conflicting domainIDs. | 1.3.6.1.4.1.9.9.371.1.2.3 | FcAddressId | accessible-for-notify | current |
| civDomainIdConflictVsan OBJECT-TYPE The VSAN in which the domainID conflict occurred. | 1.3.6.1.4.1.9.9.371.1.2.4 | VsanIndex | accessible-for-notify | current |
| civrZoneSetActDeactPartialSucss OBJECT-TYPE This object indicates if the IV zoneset activation/deactivation was partially success. | 1.3.6.1.4.1.9.9.371.1.2.5 | TruthValue | accessible-for-notify | current |
| civrAfidMisConfigVsan OBJECT-TYPE The VSAN in which the AFID mis-configuration occurred. | 1.3.6.1.4.1.9.9.371.1.2.6 | VsanIndex | accessible-for-notify | current |
| civrAfidMisConfigLocalAfid OBJECT-TYPE The local AFID value in which the AFID mis-configuration occurred. | 1.3.6.1.4.1.9.9.371.1.2.7 | CIvrAutonomousFabricId | accessible-for-notify | current |
| civrAfidMisConfigRemoteAfid OBJECT-TYPE The remote AFID value in which the AFID mis-configuration occurred. | 1.3.6.1.4.1.9.9.371.1.2.8 | CIvrAutonomousFabricId | accessible-for-notify | current |
| civrAfidMisConfigLocalSWwn OBJECT-TYPE The local switch WWN in which the AFID mis-configuration occurred. | 1.3.6.1.4.1.9.9.371.1.2.9 | FcNameId | accessible-for-notify | current |
| civrAfidMisConfigRemoteSWwn OBJECT-TYPE The remote switch WWN in which the AFID mis-configuration occurred. | 1.3.6.1.4.1.9.9.371.1.2.10 | FcNameId | accessible-for-notify | current |
| civrTopologyMisConfigReason OBJECT-TYPE The reason for a topology mis-configuration. | 1.3.6.1.4.1.9.9.371.1.2.11 | INTEGER {unknown(1), afidMismatch(2)} | accessible-for-notify | current |
| ciscoIvrMIBConformance OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.2 | |||
| civrZoneServerMIBCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.2.1 | |||
| civrZoneServerMIBGroups OBJECT-IDENTITY | 1.3.6.1.4.1.9.9.371.2.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| civrZoneActivationDoneNotify NOTIFICATION-TYPE This notification is generated on completion of an IV zoneset activation. civrZoneSetActDeactPartialSucss is valid only if the activation was successful. | 1.3.6.1.4.1.9.9.371.0.1 | current |
| civrZoneDeactivationDoneNotify NOTIFICATION-TYPE This notification is generated on completion of an IV zoneset deactivation. civrZoneSetActDeactPartialSucss is valid only if the deactivation was successful. | 1.3.6.1.4.1.9.9.371.0.2 | current |
| civrDomainConflictNotify NOTIFICATION-TYPE This notification is sent when domainID conflict occurs in a VSAN. The domainIDs in all the VSANs (dmDatabaseTable in CISCO-DM-MIB) which are configured to be carrying inter-VSAN trafic (civrTopologyConfigTable) must be unique. If not, there could be domainID conflicts. | 1.3.6.1.4.1.9.9.371.0.3 | current |
| civrAfidConfigNotify NOTIFICATION-TYPE This notification is sent when an IVR AFID mis-configuration occurs. | 1.3.6.1.4.1.9.9.371.0.4 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| civrZoneServerMIBCompliance MODULE-COMPLIANCE The compliance statement for entities which implement the Zone Server. | 1.3.6.1.4.1.9.9.371.2.1.1 | deprecated |
| civrZoneServerMIBComplianceRev1 MODULE-COMPLIANCE The compliance statement for entities which implement the Zone Server. | 1.3.6.1.4.1.9.9.371.2.1.2 | deprecated |
| civrZoneServerMIBComplianceRev2 MODULE-COMPLIANCE The compliance statement for entities which implement the Zone Server. | 1.3.6.1.4.1.9.9.371.2.1.3 | current |
| civrZoneConfigurationGroup OBJECT-GROUP A collection of objects for displaying and configuring IvrZone Membership. | 1.3.6.1.4.1.9.9.371.2.2.1 | current |
| civrTopologyGroup OBJECT-GROUP A collection of objects for IVR topology. | 1.3.6.1.4.1.9.9.371.2.2.2 | current |
| civrStatsGroup OBJECT-GROUP A collection of objects for IVR status/statistics. | 1.3.6.1.4.1.9.9.371.2.2.3 | current |
| civrNotificationGroup NOTIFICATION-GROUP A collection of notification(s) for monitoring IVR related events. | 1.3.6.1.4.1.9.9.371.2.2.4 | current |
| civrVirtualDomainsGroup OBJECT-GROUP A collection of objects for IVR status/statistics. | 1.3.6.1.4.1.9.9.371.2.2.5 | current |
| civrGenericGroup OBJECT-GROUP A collection of objects for IVR generic configurations. | 1.3.6.1.4.1.9.9.371.2.2.6 | current |
| civrTopologyGroupRev2 OBJECT-GROUP A collection of objects for IVR topology. | 1.3.6.1.4.1.9.9.371.2.2.7 | current |
| civrZoneConfigurationGroupRev2 OBJECT-GROUP A collection of objects to support SCSI read only, Qos and Lun zoning in IVR Zone Membership configurations. | 1.3.6.1.4.1.9.9.371.2.2.8 | current |
| civrNotificationGroupRev2 NOTIFICATION-GROUP A collection of notification(s) for monitoring IVR related events. | 1.3.6.1.4.1.9.9.371.2.2.9 | current |