CISCO-IETF-MPLS-TE-P2MP-STD-MIB
- Registered at
- 1.3.6.1.4.1.9.10.142
- Last updated
- 2009-09-30 00:00
- Organization
- Cisco Systems, Inc.
- Revisions
- 2009-09-30 00:00, 2009-09-01 00:00, 2009-05-07 00:00
- Namespace
- cisco
- Source file
CISCO-IETF-MPLS-TE-P2MP-STD-MIB- Digest
sha256:21d63c02fa987ff6ee6c440303cfadd2b79c3bf2b47e807592876227f61da809
Description
This MIB module contains managed object definitions for Point-to-Multipoint (P2MP) MPLS Traffic Engineering (TE) defined in: 1. Signaling Requirements for Point-to-Multipoint Traffic-Engineered MPLS Label Switched Paths (LSPs), S. Yasukawa, RFC 4461, April 2006. 2. Extensions to Resource Reservation Protocol - Traffic Engineering (RSVP-TE) for Point-to-Multipoint TE Label Switched Paths (LSPs), Aggarwal, R., Papadimitriou, D., and Yasukawa, S., RFC 4875, May 2007.
Contact
Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-snmp@cisco.com
Imports
| From | Symbols |
|---|---|
| CISCO-SMI | ciscoExperiment |
| DIFFSERV-MIB | IndexInteger, IndexIntegerNextFree |
| IF-MIB | InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
| MPLS-LSR-STD-MIB | MplsIndexType |
| MPLS-TC-STD-MIB | MplsLabel, MplsPathIndexOrZero |
| MPLS-TE-STD-MIB | mplsTunnelEgressLSRId, mplsTunnelIndex, mplsTunnelIngressLSRId, mplsTunnelInstance |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Counter32, Counter64, MODULE-IDENTITY, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, RowStatus, StorageType, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
Imported by
Nothing in this corpus imports this module.
Load order
Every file a consumer needs in order to load this module, dependencies first.
CISCO-IETF-MPLS-TE-P2MP-STD-MIB CISCO-SMI DIFFSERV-DSCP-TC DIFFSERV-MIB IANA-ADDRESS-FAMILY-NUMBERS-MIB IANAifType-MIB IF-MIB INET-ADDRESS-MIB INTEGRATED-SERVICES-MIB MPLS-LSR-STD-MIB MPLS-TC-STD-MIB MPLS-TE-STD-MIB SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-MIB SNMPv2-SMI SNMPv2-TC
Objects
| Name | OID | Syntax | Access | Status |
|---|---|---|---|---|
| cmplsTeP2mpNotifications OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.142.0 | |||
| cmplsTeP2mpScalars OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.142.1 | |||
| cmplsTeP2mpTunnelConfigured OBJECT-TYPE The number of P2MP tunnels configured on this device. A tunnel is considered configured if the mplsTunnelRowStatus in MPLS-TE-STD-MIB is active(1). | 1.3.6.1.4.1.9.10.142.1.1 | Unsigned32 | read-only | current |
| cmplsTeP2mpTunnelActive OBJECT-TYPE The number of P2MP tunnels active on this device. A tunnel is considered active if the mplsTunnelOperStatus in MPLS-TE-STD-MIB is up(1). | 1.3.6.1.4.1.9.10.142.1.2 | Unsigned32 | read-only | current |
| cmplsTeP2mpTunnelTotalMaxHops OBJECT-TYPE The maximum number of hops that can be specified for an entire P2MP tunnel on this device. This object should be used in conjunction with mplsTunnelMaxHops in MPLS-TE-STD-MIB that is used in the context of P2MP tunnels to express the maximum number of hops to any individual destination of a P2MP tunnel that can be configured on this device. cmplsTeP2mpTunnelTotalMaxHops would normally be set larger than or equal to mplsTunnelMaxHops. | 1.3.6.1.4.1.9.10.142.1.3 | Unsigned32 | read-only | current |
| cmplsTeP2mpObjects OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.142.2 | |||
| cmplsTeP2mpTunnelTable OBJECT-TYPE The cmplsTeP2mpTunnelTable allows new P2MP MPLS tunnels to be created between an LSR and one or more remote end-points, and existing P2MP tunnels to be reconfigured or removed. This table sparse augments mplsTunnelTable in MPLS-TE-STD-MIB such that entries in that table can be flagged as point-to-multipoint, and can be configured and monitored appropriately. | 1.3.6.1.4.1.9.10.142.2.1 | not-accessible | current | |
| cmplsTeP2mpTunnelEntry OBJECT-TYPE An entry in this table represents a P2MP MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol. An entry in this table MUST correspond to an entry in the mplsTunnelTable in MPLS-TE-STD-MIB. This table shares index objects with that table and sparse augments that table. Thus, an entry in this table can only be created at the same time as or after a corresponding entry in mplsTunnelTable, and an entry in mplsTunnelTable cannot be deleted while a corresponding entry exists in this table. This table entry includes a row status object, but administrative and operational statuses should be taken from mplsTunnelAdminStatus and mplsTunnelOperStatus in the corresponding entry in mplsTunnelTable. | 1.3.6.1.4.1.9.10.142.2.1.1 | not-accessible | current | |
| cmplsTeP2mpTunnelP2mpIntegrity OBJECT-TYPE Denotes whether or not P2MP Integrity is required for this tunnel. If P2MP integrity is operational on a P2MP tunnel then the failure of the path to any of the tunnel destinations should cause the teardown of the entire P2MP tunnel. | 1.3.6.1.4.1.9.10.142.2.1.1.2 | TruthValue | read-create | current |
| cmplsTeP2mpTunnelBranchRole OBJECT-TYPE This value supplements the value in the object mplsTunnelRole in MPLS-TE-STD-MIB that indicates the role of this LSR in the tunnel represented by this entry in cmplsTeP2mpTunnelTable. mplsTunnelRole may take any of the values: head(1), transit(2), tail(3), headTail(4) If this LSR is an ingress and there is exactly one out-segment, mplsTunnelRole should contain the value head(1), and cmplsTeP2mpTunnelBranchRole should have the value notBranch(1). If this LSR is an ingress with more than one out segment, mplsTunnelRole should contain the value head(1), and cmplsTeP2mpTunnelBranchRole should have the value branch(2). If this LSR is an ingress, an egress, and there is one or more out-segments, mplsTunnelRole should contain the value headTail(4), and cmplsTeP2mpTunnelBranchRole should have the value bud(3). If this LSR is a transit with exactly one out-segment, mplsTunnelRole should contain the value transit(2), and cmplsTeP2mpTunnelBranchRole should have the value notBranch(1). If this LSR is a transit with more than one out-segment, mplsTunnelRole should contain the value transit(2), and cmplsTeP2mpTunnelBranchRole should have the value branch(2). If this LSR is a transit with one or more out-segments and is also an egress, mplsTunnelRole should contain the value transit(2), and cmplsTeP2mpTunnelBranchRole should have the value bud(3). If this LSR is an egress with no out-segment and is not the ingress, mplsTunnelRole should contain the value tail(3), and cmplsTeP2mpTunnelBranchRole should have the value notBranch(1). If this LSR is an egress and has one or more out-segments, mplsTunnelRole should contain the value transit(1), and cmplsTeP2mpTunnelBranchRole should have the value bud(3). | 1.3.6.1.4.1.9.10.142.2.1.1.3 | INTEGER {notBranch(1), branch(2), bud(3)} | read-create | current |
| cmplsTeP2mpTunnelP2mpXcIndex OBJECT-TYPE This object contains the value of mplsXCIndex, the primary index of the mplsXCTable for all cross-connect entries for this P2MP LSP. If no XC entries have been created yet, this object must return zero. The set of entries in the mplsXCTable for this P2MP LSP can be walked by reading Get-or-GetNext starting with the three indexes to mplsXCTable set as: mplsXCIndex = the value of this object mplsXCInSegmentIndex = 0x0 mplsXCOutSegmentIndex = 0x0 | 1.3.6.1.4.1.9.10.142.2.1.1.4 | MplsIndexType | read-only | current |
| cmplsTeP2mpTunnelRowStatus OBJECT-TYPE This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modified by the agent except cmplsTeP2mpTunnelRowStatus and cmplsTeP2mpTunnelStorageType. This object and mplsTunnelRowStatus in the corresponding entry in mplsTunnelTable in MPLS-TE-STD-MIB should be managed together. No objects in a row in this table can be modified when the mplsTunnelRowStatus object in the corresponding row in mplsTunnelTable has value active(1). Note that no admin or oper status objects are provided in this table. The administrative and operational status of P2MP tunnels is taken from the values of mplsTunnelAdminStatus and mplsTunnelOperStatus in the corresponding row mplsTunnelTable. | 1.3.6.1.4.1.9.10.142.2.1.1.5 | RowStatus | read-create | current |
| cmplsTeP2mpTunnelStorageType OBJECT-TYPE The storage type for this tunnel entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. | 1.3.6.1.4.1.9.10.142.2.1.1.6 | StorageType | read-create | current |
| cmplsTeP2mpTunnelSubGroupIDNext OBJECT-TYPE This object contains an unused value for cmplsTeP2mpTunnelDestSubGroupID, or a zero to indicate that none exists. Negative values are not allowed, as they do not correspond to valid values of cmplsTeP2mpTunnelDestSubGroupID. Note that this object offers an unused value for an cmplsTeP2mpTunnelDestSubGroupID value at the local LSR when it is a sub-group originator. In other cases, the value of cmplsTeP2mpTunnelDestSubGroupID SHOULD be taken from the received value signaled by the signaling protocol and corresponds to the value in cmplsTeP2mpTunnelDestSrcSubGroupID. | 1.3.6.1.4.1.9.10.142.2.2 | IndexIntegerNextFree (0..65535) | read-only | current |
| cmplsTeP2mpTunnelDestTable OBJECT-TYPE The cmplsTeP2mpTunnelDestTable allows new destinations of P2MP MPLS tunnels to be added to and removed from P2MP tunnels. | 1.3.6.1.4.1.9.10.142.2.3 | not-accessible | current | |
| cmplsTeP2mpTunnelDestEntry OBJECT-TYPE An entry in this table represents a destination of a P2MP MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol. Entries in this table share some index fields with the cmplsTeP2mpTunnelTable and the mplsTunnelTable in MPLS-TE-STD-MIB. Entries in this table have no meaning unless there is a corresponding entry in cmplsTeP2mpTunnelTable (which, itself, depends on a corresponding entry in mplsTunnelTable). Note that the same destination may be present more than once if it is in more than one sub-group as reflected by the cmplsTeP2mpTunnelDestSrcSubGroupOriginType, cmplsTeP2mpTunnelDestSrcSubGroupOrigin, cmplsTeP2mpTunnelDestSrcSubGroupID, cmplsTeP2mpTunnelDestSubGroupOriginType, cmplsTeP2mpTunnelDestSubGroupOrigin, and cmplsTeP2mpTunnelDestSubGroupID, index objects. Entries in this table may be created at any time. If created before an entry in the cmplsTeP2mpTunnelTable the entries have no meaning, but may be kept ready for the creation of the P2MP tunnel. If created after the entry in cmplsTeP2mpTunnelTable, entries in this table may reflect the addition of destinations to active P2MP tunnels. For this reason, entries in this table are equipped with row, admin, and oper status objects. | 1.3.6.1.4.1.9.10.142.2.3.1 | not-accessible | current | |
| cmplsTeP2mpTunnelDestSrcSubGroupOriginType OBJECT-TYPE This object identifies the type of address carried in cmplsTeP2mpTunnelDestSrcSubGroupOrigin. Since the object cmplsTeP2mpTunnelDestSrcSubGroupOrigin must conform to the protocol specification, this object must return either ipv4(1) or ipv6(2) at a transit or egress LSR. At an ingress LSR, there is no source sub-group and this object should return the value unknown(0). | 1.3.6.1.4.1.9.10.142.2.3.1.1 | InetAddressType | not-accessible | current |
| cmplsTeP2mpTunnelDestSrcSubGroupOrigin OBJECT-TYPE The TE Router ID (reachable and stable IP address) of the originator of the P2MP sub-group as received on a Path message by a transit or egress LSR. This object is interpreted in the context of cmplsTeP2mpTunnelDestSrcSubGroupOriginType. The value of the sub-group originator used on outgoing Path messages is found in cmplsTeP2mpTunnelDestSubGroupOrigin and is copied from this object unless this LSR is responsible for changing the sub-group ID. At an ingress LSR there is no received Path message. cmplsTeP2mpTunnelDestSrcSubGroupOriginType should return unknown(0), and this object should return a zero-length string. | 1.3.6.1.4.1.9.10.142.2.3.1.2 | InetAddress (SIZE(0 | 4 | 16)) | not-accessible | current |
| cmplsTeP2mpTunnelDestSrcSubGroupID OBJECT-TYPE The unique identifier assigned by the sub-group originator for this sub-group of this P2MP tunnel as received on a Path message by a transit or egress LSR. The value of the sub-group identifier used on outgoing Path messages is found in cmplsTeP2mpTunnelDestSubGroupID and is copied from this object unless this LSR is responsible for changing the sub-group ID. At an ingress LSR there is no received Path message, and this object should return zero. | 1.3.6.1.4.1.9.10.142.2.3.1.3 | IndexInteger (1..65535) | not-accessible | current |
| cmplsTeP2mpTunnelDestSubGroupOriginType OBJECT-TYPE This object identifies the type of address carried in cmplsTeP2mpTunnelDestSubGroupOrigin. This object must return either ipv4(1) or ipv6(2) in keeping with the protocol specification. | 1.3.6.1.4.1.9.10.142.2.3.1.4 | InetAddressType | not-accessible | current |
| cmplsTeP2mpTunnelDestSubGroupOrigin OBJECT-TYPE The TE Router ID (reachable and stable IP address) of the originator of the P2MP sub-group. In many cases, this will be the ingress LSR of the P2MP tunnel and will be the received signaled value as available in cmplsTeP2mpTunnelDestSrcSubGroupOrigin. When a signaling protocol is used, this object corresponds to the Sub-Group Originator field in the SENDER_TEMPLATE object. This object is interpreted in the context of cmplsTeP2mpTunnelDestSubGroupOriginType. | 1.3.6.1.4.1.9.10.142.2.3.1.5 | InetAddress (SIZE(4 | 16)) | not-accessible | current |
| cmplsTeP2mpTunnelDestSubGroupID OBJECT-TYPE The unique identifier assigned by the sub-group originator for this sub-group of this P2MP tunnel. An appropriate value for this object during row creation when the sub-group origin in cmplsTeP2mpTunnelDestSubGroupOrigin is the local LSR can be obtained by reading cmplsTeP2mpTunnelSubGroupIDNext. At an egress, there is no downstream sub-group ID. This object should return the value received from upstream and reported in cmplsTeP2mpTunnelDestSrcSubGroupID. | 1.3.6.1.4.1.9.10.142.2.3.1.6 | IndexInteger (1..65535) | not-accessible | current |
| cmplsTeP2mpTunnelDestDestinationType OBJECT-TYPE This object identifies the type of address carried in cmplsTeP2mpTunnelDestDestination. This object forms part of the index of this table and can, therefore, not return the value unknown(0). Similarly, since the object cmplsTeP2mpTunnelDestDestination must conform to the protocol specification, this object must return either ipv4(1) or ipv6(2). | 1.3.6.1.4.1.9.10.142.2.3.1.7 | InetAddressType | not-accessible | current |
| cmplsTeP2mpTunnelDestDestination OBJECT-TYPE A single destination of this P2MP tunnel. That is, a routable TE address of a leaf. This will often be the TE Router ID of the leaf, but can be any interface address. When a signaling protocol is used, this object corresponds to the S2L Sub-LSP destination address field in the S2L_SUB_LSP object. This object is interpreted in the context of cmplsTeP2mpTunnelDestDestinationType. | 1.3.6.1.4.1.9.10.142.2.3.1.8 | InetAddress (SIZE(4 | 16)) | not-accessible | current |
| cmplsTeP2mpTunnelDestBranchOutSegment OBJECT-TYPE This object identifies the outgoing branch from this LSR towards the destination represented by this table entry. It must be a unique identifier within the scope of this tunnel. If MPLS-LSR-STD-MIB is implemented, this object should contain an index into mplsOutSegmentTable. If MPLS-LSR-STD-MIB is not implemented, the LSR should assign a unique value to each branch of the tunnel. The value of this object is also used as an index into cmplsTeP2mpTunnelBranchPerfTable. | 1.3.6.1.4.1.9.10.142.2.3.1.9 | MplsIndexType | read-only | current |
| cmplsTeP2mpTunnelDestHopTableIndex OBJECT-TYPE Index into the mplsTunnelHopTable entry that specifies the explicit route hops for this destination of the P2MP tunnel. This object represents the configured route for the branch of the P2MP tree to this destination and is meaningful only at the head-end (ingress or root) of the P2MP tunnel. Note that many such paths may be configured within the mplsTunnelHopTable for each destination, and that the object cmplsTeP2mpTunnelDestPathInUse identifies which path has been selected for use. | 1.3.6.1.4.1.9.10.142.2.3.1.10 | MplsPathIndexOrZero | read-create | current |
| cmplsTeP2mpTunnelDestPathInUse OBJECT-TYPE This value denotes the configured path that was chosen as the explicit path to this destination of this P2MP tunnel. This value reflects the secondary index into mplsTunnelHopTable where the primary index comes from cmplsTeP2mpTunnelDestHopTableIndex. The path indicated by this object might not exactly match the one signaled and recorded in mplsTunnelCHopTable as specific details of the path might be computed locally. Similarly, the path might not match the actual path in use as recorded in mplsTunnelARHopTable due to the fact that some details of the path may have been resolved within the network. A value of zero denotes that no path is currently in use or available. | 1.3.6.1.4.1.9.10.142.2.3.1.11 | MplsPathIndexOrZero | read-create | current |
| cmplsTeP2mpTunnelDestCHopTableIndex OBJECT-TYPE Index into the mplsTunnelCHopTable that identifies the explicit path for this destination of the P2MP tunnel. This path is based on the chosen configured path identified by cmplsTeP2mpTunnelDestHopTableIndex and cmplsTeP2mpTunnelDestPathInUse, but may have been modified and automatically updated by the agent when computed hops become available or when computed hops get modified. If this destination is the destination of the 'first S2L sub-LSP' then this path will be signaled in the Explicit Route Object. If this destination is the destination of a 'subsequent S2L sub-LSP' then this path will be signaled in a Secondary Explicit Route Object. | 1.3.6.1.4.1.9.10.142.2.3.1.12 | MplsPathIndexOrZero | read-only | current |
| cmplsTeP2mpTunnelDestARHopTableIndex OBJECT-TYPE Index into the mplsTunnelARHopTable that identifies the actual hops traversed to this destination of the P2MP tunnel. This is automatically updated by the agent when the actual hops becomes available. If this destination is the destination of the 'first S2L sub-LSP' then this path will be signaled in the Recorded Route Object. If this destination is the destination of a 'subsequent S2L sub-LSP' then this path will be signaled in a Secondary Recorded Route Object. | 1.3.6.1.4.1.9.10.142.2.3.1.13 | MplsPathIndexOrZero | read-only | current |
| cmplsTeP2mpTunnelDestTotalUpTime OBJECT-TYPE This value represents the aggregate up time for all instances of this tunnel to this destination, if this information is available. If this information is not available, this object MUST return a value of 0. | 1.3.6.1.4.1.9.10.142.2.3.1.14 | TimeTicks | read-only | current |
| cmplsTeP2mpTunnelDestInstanceUpTime OBJECT-TYPE This value identifies the total time that the currently active tunnel instance to this destination has had its operational status (mplsTeP2mpTunnelDestOperStatus) set to up(1) since it was last previously not up(1). | 1.3.6.1.4.1.9.10.142.2.3.1.15 | TimeTicks | read-only | current |
| cmplsTeP2mpTunnelDestPathChanges OBJECT-TYPE This object counts the number of times the actual path for this destination of this P2MP tunnel instance has changed. This object should be read in conjunction with cmplsTeP2mpTunnelDestDiscontinuityTime. | 1.3.6.1.4.1.9.10.142.2.3.1.16 | Counter32 | read-only | current |
| cmplsTeP2mpTunnelDestLastPathChange OBJECT-TYPE Specifies the time since the last change to the actual path for this destination of this P2MP tunnel instance. | 1.3.6.1.4.1.9.10.142.2.3.1.17 | TimeTicks | read-only | current |
| cmplsTeP2mpTunnelDestCreationTime OBJECT-TYPE Specifies the value of sysUpTime when the first instance of this tunnel came into existence for this destination. That is, when the value of cmplsTeP2mpTunnelDestOperStatus was first set to up(1). | 1.3.6.1.4.1.9.10.142.2.3.1.18 | TimeStamp | read-only | current |
| cmplsTeP2mpTunnelDestStateTransitions OBJECT-TYPE This object counts the number of times the status (mplsTeP2mpTunnelDestOperStatus) of this tunnel instance to this destination has changed. This object should be read in conjunction with cmplsTeP2mpTunnelDestDiscontinuityTime. | 1.3.6.1.4.1.9.10.142.2.3.1.19 | Counter32 | read-only | current |
| cmplsTeP2mpTunnelDestDiscontinuityTime OBJECT-TYPE The value of sysUpTime on the most recent occasion at which any one or more of this row's Counter32 objects experienced a discontinuity. If no such discontinuity has occurred since the last re-initialization of the local management subsystem, then this object contains a zero value. | 1.3.6.1.4.1.9.10.142.2.3.1.20 | TimeStamp | read-only | current |
| cmplsTeP2mpTunnelDestAdminStatus OBJECT-TYPE Indicates the desired operational status of this destination of this P2MP tunnel. | 1.3.6.1.4.1.9.10.142.2.3.1.21 | INTEGER {up(1), down(2), testing(3)} | read-create | current |
| cmplsTeP2mpTunnelDestOperStatus OBJECT-TYPE Indicates the actual operational status of this destination of this P2MP tunnel. This object may be compared to mplsTunnelOperStatus that includes two other values: dormant(5) -- some component is missing notPresent(6) -- down due to the state of -- lower layer interfaces. These states do not apply to an individual destination of a P2MP MPLS-TE LSP and so are not included in this object. | 1.3.6.1.4.1.9.10.142.2.3.1.22 | INTEGER {up(1), down(2), testing(3), unknown(4), lowerLayerDown(7)} | read-only | current |
| cmplsTeP2mpTunnelDestRowStatus OBJECT-TYPE This object is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modified by SET operations except cmplsTeP2mpTunnelDestAdminStatus and cmplsTeP2mpTunnelDestStorageType. | 1.3.6.1.4.1.9.10.142.2.3.1.23 | RowStatus | read-create | current |
| cmplsTeP2mpTunnelDestStorageType OBJECT-TYPE The storage type for this table entry. Conceptual rows having the value 'permanent' need not allow write-access to any columnar objects in the row. | 1.3.6.1.4.1.9.10.142.2.3.1.24 | StorageType | read-create | current |
| cmplsTeP2mpTunnelBranchPerfTable OBJECT-TYPE This table provides per-tunnel branch MPLS performance information. This table is not valid for switching types other than packet. | 1.3.6.1.4.1.9.10.142.2.4 | not-accessible | current | |
| cmplsTeP2mpTunnelBranchPerfEntry OBJECT-TYPE An entry in this table is created by the LSR for each downstream branch (out-segment) from this LSR for this P2MP tunnel. More than one destination as represented by an entry in the cmplsTeP2mpTunnelDestTable may be reached through a single out-segment. More than one out-segment may belong to a single P2MP tunnel represented by an entry in cmplsTeP2mpTunnelTable. Each entry in the table is indexed by the four identifiers of the P2MP tunnel, and the out-segment that identifies the outgoing branch. | 1.3.6.1.4.1.9.10.142.2.4.1 | not-accessible | current | |
| cmplsTeP2mpTunnelBranchPerfBranch OBJECT-TYPE This object identifies an outgoing branch from this LSR for this tunnel. Its value is unique within the context of the tunnel. If MPLS-LSR-STD-MIB is implemented, this object should contain an index into mplsOutSegmentTable. Under all circumstances, this object should contain the same value as cmplsTeP2mpTunnelDestBranchOutSegment for destinations reached on this branch. | 1.3.6.1.4.1.9.10.142.2.4.1.1 | MplsIndexType | not-accessible | current |
| cmplsTeP2mpTunnelBranchPerfPackets OBJECT-TYPE Number of packets forwarded by the tunnel onto this branch. This object should represents the 32-bit value of the least significant part of the 64-bit value if both cmplsTeP2mpTunnelBranchPerfHCPackets is returned. This object should be read in conjunction with cmplsTeP2mpTunnelBranchDiscontinuityTime. | 1.3.6.1.4.1.9.10.142.2.4.1.2 | Counter32 | read-only | current |
| cmplsTeP2mpTunnelBranchPerfHCPackets OBJECT-TYPE High capacity counter for number of packets forwarded by the tunnel onto this branch. This object should be read in conjunction with cmplsTeP2mpTunnelBranchDiscontinuityTime. | 1.3.6.1.4.1.9.10.142.2.4.1.3 | Counter64 | read-only | current |
| cmplsTeP2mpTunnelBranchPerfErrors OBJECT-TYPE Number of packets dropped because of errors or for other reasons, that were supposed to be forwarded onto this branch for this tunnel. This object should be read in conjunction with cmplsTeP2mpTunnelBranchDiscontinuityTime. | 1.3.6.1.4.1.9.10.142.2.4.1.4 | Counter32 | read-only | current |
| cmplsTeP2mpTunnelBranchPerfBytes OBJECT-TYPE Number of bytes forwarded by the tunnel onto this branch. This object should represents the 32-bit value of the least significant part of the 64-bit value if both cmplsTeP2mpTunnelBranchPerfHCBytes is returned. This object should be read in conjunction with cmplsTeP2mpTunnelBranchDiscontinuityTime. | 1.3.6.1.4.1.9.10.142.2.4.1.5 | Counter32 | read-only | current |
| cmplsTeP2mpTunnelBranchPerfHCBytes OBJECT-TYPE High capacity counter for number of bytes forwarded by the tunnel onto this branch. This object should be read in conjunction with cmplsTeP2mpTunnelBranchDiscontinuityTime. | 1.3.6.1.4.1.9.10.142.2.4.1.6 | Counter64 | read-only | current |
| cmplsTeP2mpTunnelBranchDiscontinuityTime OBJECT-TYPE The value of sysUpTime on the most recent occasion at which any one or more of this row's Counter32 or Counter64 objects experienced a discontinuity. If no such discontinuity has occurred since the last re-initialization of the local management subsystem, then this object contains a zero value. | 1.3.6.1.4.1.9.10.142.2.4.1.7 | TimeStamp | read-only | current |
| cmplsTeP2mpTunnelBranchLocalLabel OBJECT-TYPE The local MPLS label for this branch. This object is not part of the original draft | 1.3.6.1.4.1.9.10.142.2.4.1.8 | MplsLabel | read-only | current |
| cmplsTeP2mpTunnelBranchOutIfIndex OBJECT-TYPE This is the index of outgoing TE link physical I/F for the P2MP egress tunnel branch. It is non-zero when the P2MP tunnel's outgoing branch has been signaled. This object is not part of the original draft | 1.3.6.1.4.1.9.10.142.2.4.1.9 | InterfaceIndexOrZero | read-only | current |
| cmplsTeP2mpTunnelBranchOutLabel OBJECT-TYPE The outgoing MPLS label for this branch. | 1.3.6.1.4.1.9.10.142.2.4.1.10 | MplsLabel | read-only | current |
| cmplsTeP2mpTunnelBranchSignalArea OBJECT-TYPE This is the IGP area instance name/number that the outgoing tunnel branch is signaled in. TE can allow (currently not supported for P2MP tunnels but could be in the future) the operator to restrict path computation to specific areas and this represents the actual IGP instance/area that this outgoing branch is taking. This object is not part of the original draft | 1.3.6.1.4.1.9.10.142.2.4.1.11 | OCTET STRING | read-only | current |
| cmplsTeP2mpTunnelBranchInIfIndex OBJECT-TYPE This is the index of incoming TE link physical I/F for the P2MP ingress tunnel branch. It is non-zero when the P2MP tunnel's incoming branch has been signaled and it is applicable only on mid point routers for tunnels having out-segment up and running. This object is not part of the original draft | 1.3.6.1.4.1.9.10.142.2.4.1.12 | InterfaceIndexOrZero | read-only | current |
| cmplsTeP2mpTunnelNotificationEnable OBJECT-TYPE If this object is true(1), then it enables the generation of cmplsTeP2mpTunnelDestUp and cmplsTeP2mpTunnelDestDown notifications. Otherwise these notifications are not emitted. Note that when tunnels have large numbers of destinations, setting this object to true(1) may result in the generation of large numbers of notifications. | 1.3.6.1.4.1.9.10.142.2.5 | TruthValue | read-write | current |
| cmplsTeP2mpConformance OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.142.3 | |||
| cmplsTeP2mpGroups OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.142.3.1 | |||
| cmplsTeP2mpCompliances OBJECT-IDENTITY | 1.3.6.1.4.1.9.10.142.3.2 |
Notifications
| Name | OID | Status |
|---|---|---|
| cmplsTeP2mpTunnelDestUp NOTIFICATION-TYPE This notification is generated when a cmplsTeP2mpTunnelDestOperStatus object for one of the destinations of one of the configured tunnels is about to leave the down(2) state and transition into some other state. This other state is indicated by the included value of cmplsTeP2mpTunnelDestOperStatus. This reporting of state transitions mirrors mplsTunnelUp. | 1.3.6.1.4.1.9.10.142.0.1 | current |
| cmplsTeP2mpTunnelDestDown NOTIFICATION-TYPE This notification is generated when a cmplsTeP2mpTunnelDestOperStatus object for one of the destinations of one of the configured tunnels is about to enter the down(2) state from some other state. This other state is indicated by the included value of cmplsTeP2mpTunnelDestOperStatus. This reporting of state transitions mirrors mplsTunnelDown. | 1.3.6.1.4.1.9.10.142.0.2 | current |
Conformance
| Name | OID | Status |
|---|---|---|
| cmplsTeP2mpGeneralGroup OBJECT-GROUP Collection of objects needed for MPLS P2MP. | 1.3.6.1.4.1.9.10.142.3.1.1 | current |
| cmplsTeP2mpNotifGroup NOTIFICATION-GROUP Notifications implemented in this module. | 1.3.6.1.4.1.9.10.142.3.1.2 | current |
| cmplsTeP2mpScalarGroup OBJECT-GROUP Scalar objects needed to implement P2MP MPLS tunnels. | 1.3.6.1.4.1.9.10.142.3.1.3 | current |
| cmplsTeP2mpGeneralGroupSup1 OBJECT-GROUP Addition to collection of objects needed for MPLS P2MP. | 1.3.6.1.4.1.9.10.142.3.1.4 | current |
| cmplsTeP2mpGeneralGroupSup2 OBJECT-GROUP Addition to collection of objects needed for MPLS P2MP. | 1.3.6.1.4.1.9.10.142.3.1.5 | current |
| cmplsTeP2mpModuleFullCompliance MODULE-COMPLIANCE Compliance statement for agents that provide full support for MPLS-TE-P2MP-STD-MIB. Such devices can be monitored and also be configured using this MIB module. The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-COMPLIANCE. | 1.3.6.1.4.1.9.10.142.3.2.1 | deprecated |
| cmplsTeP2mpModuleReadOnlyCompliance MODULE-COMPLIANCE Compliance statement for agents that provide read-only support for MPLS-TE-P2MP-STD-MIB. Such devices can only be monitored using this MIB module. The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE. | 1.3.6.1.4.1.9.10.142.3.2.2 | deprecated |
| cmplsTeP2mpModuleFullComplianceRev1 MODULE-COMPLIANCE Compliance statement for agents that provide full support for MPLS-TE-P2MP-STD-MIB. Such devices can be monitored and also be configured using this MIB module. The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-COMPLIANCE. | 1.3.6.1.4.1.9.10.142.3.2.3 | deprecated |
| cmplsTeP2mpModuleReadOnlyComplianceRev1 MODULE-COMPLIANCE Compliance statement for agents that provide read-only support for MPLS-TE-P2MP-STD-MIB. Such devices can only be monitored using this MIB module. The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE. | 1.3.6.1.4.1.9.10.142.3.2.4 | deprecated |
| cmplsTeP2mpModuleFullComplianceRev2 MODULE-COMPLIANCE Compliance statement for agents that provide full support for MPLS-TE-P2MP-STD-MIB. Such devices can be monitored and also be configured using this MIB module. The Module is implemented with support for read-create and read-write. In other words, both monitoring and configuration are available when using this MODULE-COMPLIANCE. | 1.3.6.1.4.1.9.10.142.3.2.5 | current |
| cmplsTeP2mpModuleReadOnlyComplianceRev2 MODULE-COMPLIANCE Compliance statement for agents that provide read-only support for MPLS-TE-P2MP-STD-MIB. Such devices can only be monitored using this MIB module. The Module is implemented with support for read-only. In other words, only monitoring is available by implementing this MODULE-COMPLIANCE. | 1.3.6.1.4.1.9.10.142.3.2.6 | current |